ASR 1000 Series

Cisco ASR 1000 Series Aggregation
Services Routers Hardware Installation

and Initial Configuration Guide
November 2008
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Text Part Number: OL-13208-03
More user manuals on ManualsBase.com

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT
TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS
MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY
PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT
SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE
OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required
to correct the interference at their own expense.
The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not
installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to
comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable
protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.
Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital
devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television
communications at your own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its
peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:
• Turn the television or radio antenna until the interference stops.
• Move the equipment to one side or the other of the television or radio.
• Move the equipment farther away from the television or radio.
• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits
controlled by different circuit breakers or fuses.)
Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.
The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public
domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH
ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF
DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,
WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
CCDE, CCENT, Cisco Eos, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, the Cisco logo, DCE, and Welcome to the Human Network
are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks; and Access Registrar, Aironet, AsyncOS, Bringing the Meeting To
You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems,
Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, EtherFast, EtherSwitch, Event Center, Fast Step, Follow Me Browsing,
FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, iQuick Study, IronPort, the IronPort logo, LightStream, Linksys, MediaTone, MeetingPlace,
MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX, PowerPanels, ProConnect, ScriptShare, SenderBase, SMARTnet,
Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc.
and/or its affiliates in the United States and certain other countries.
All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship
between Cisco and any other company. (0809R)
Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation and Initial Configuration Guide
© 2008 Cisco Systems, Inc. All rights reserved.

C O N T E N T S
Preface xi
Document Revision History xi
Document Objectives xii
Audience xii
Document Organization xii
Safety Warnings and Cautions xiii

Warning Definition xiii
Related Documentation xviii
Obtaining Documentation and Submitting a Service Request xix
CHAPTER 1 Cisco ASR 1000 Series Routers Hardware Overview 1-1
Cisco ASR 1000 Series Routers 1-2
Cisco ASR 1000 Series Routers Features 1-2
Cisco ASR 1000 Series Routers Configurations 1-3
Field-Replaceable Units 1-4
Functional Overview 1-4

Chassis Slot and Logical Interface Numbering 1-5
Cisco ASR 1006 Router Slot Numbering 1-5
MAC Address Information 1-8
Online Insertion and Removal 1-9
Environmental Monitoring and Reporting Functions 1-10
Environmental Monitoring 1-10
Fan Failures 1-11
Reporting Functions 1-11
Cisco Product Identification Standard 1-15
Unique Device Identifier 1-16
Serial Number Label Location 1-17
CHAPTER 2 Cisco ASR 1000 Series Routers Components 2-1
Cisco ASR 1000 Series Route Processor 2-1

Cisco ASR 1000 Series Route Processor Features 2-2
OL-13208-03 iii

Contents
How the Cisco ASR1000-RP1 Alarm LEDs Work 2-5

Cisco Embedded ASR1000-RP1 for Cisco ASR 1002 Router 2-6
Cisco ASR 1000 Series Embedded Services Processors 2-9
Cisco ASR 1000 Series SPA Interface Processor 2-13
Shared Port Adapters 2-14
Cisco ASR 1000 Series Router Power Supplies 2-16

Power Supply Requirements for All Cisco ASR 1000 Series Routers 2-16
DC Power System Input Requirements for Cisco ASR 1000 Series Routers 2-17
AC and DC Power Supply Types 2-17
AC and DC System Power Ratings 2-17
Power Supplies for Cisco ASR 1006 Router 2-18
AC Power Supply LEDs and Connector for Cisco ASR 1006 2-18
DC Power Supply LEDs and Connectors for Cisco ASR 1006 2-21
Cisco ASR 1004 AC Power Supply 2-23
Cisco ASR Router 1004 DC Power Supply 2-26
Cisco ASR 1002 Router AC Power Supply 2-29
Cisco ASR 1002 Router DC Power Supply 2-31
CHAPTER 3 Preparing Your Site for Installation 3-1
Safety Recommendations 3-2
Safety Warnings 3-2
Compliance Requirements 3-2
Cautions and Regulatory Compliance Statements for NEBS 3-3
Standard Warning Statements 3-4

General Safety Warnings 3-4
Site Planning 3-7
General Precautions 3-7
Site Selection Guidelines 3-8
Site Environmental Requirements 3-8
Physical Characteristics 3-8
Floor Loading Considerations 3-10
Site Power Guidelines 3-10
Electrical Circuit Requirements 3-10
Site Cabling Guidelines 3-12
Asynchronous Terminal Connections 3-13
Interference Considerations 3-13
iv OL-13208-03

Contents
Rack-Mounting and Location Guidelines 3-14

Precautions for Rack-Mounting 3-14
Rack Selection Guidelines 3-15
Equipment Rack Guidelines 3-15
Site Planning Checklist 3-17
Preventing Electrostatic Discharge Damage 3-17
Electrical Safety 3-18
Receiving a Cisco ASR 1000 Series Router 3-19
Chassis-Lifting Guidelines 3-20
Tools and Equipment 3-21

Unpacking and Verifying Shipping Contents 3-21
Checking the Shipping Container Contents 3-21
Cisco ASR 1000 Series Router Installation Checklist 3-23
CHAPTER 4 Cisco ASR 1006 Router Overview and Installation 4-1
Cisco ASR 1006 Router Description 4-1

Front View 4-2
Rear View 4-2
Installation Methods 4-4
General Rack Installation Guidelines 4-4
Guidelines for an Equipment Shelf or Tabletop Installation 4-5
Equipment Shelf or Tabletop Installation 4-6
Rack-Mounting a Cisco ASR 1006 Router 4-8

Verifying Rack Dimensions 4-8
Attaching the Chassis Rack-Mount Brackets 4-9
Chassis Front Rack-Mount Brackets 4-9
Chassis Rear Rack-Mount Brackets 4-10
Installing the Cisco ASR 1006 Router in a Rack 4-12
Two-Post Rack Installation 4-13
Four-Post Rack Installation 4-14
Attaching the Cable-Management Bracket 4-16
Attaching a Chassis Ground Connection 4-17

Recommended Tools and Supplies 4-19
Connecting Shared Port Adapter Cables 4-20
Connecting Console and Auxiliary Port Cables 4-20

Connecting the Ethernet Management Port Cable 4-21
Connecting Power to Cisco ASR 1006 Router 4-21
OL-13208-03 v

Contents
Connecting AC-Input Power to Cisco ASR 1006 Router 4-22

Connecting DC-Input Power to Cisco ASR 1006 Router 4-23
Connecting a Terminal to the Cisco ASR 1000 Series RP1 Console Port 4-27
Connecting System Cables 4-29
Auxiliary Connection 4-30

Front View 5-2
Rear View 5-3

Recommended Tools and Supplies 5-17

Connecting the Ethernet Management Port Cable 5-21

Connecting a Terminal to the Cisco ASR Series 1000 RP1 Console Port 5-29
Connecting Network Management and Signal System Cables 5-30
vi OL-13208-03

Contents
Front View 6-2

Rear View 6-3
Cisco ASR 1002 Router Components 6-4
Cisco Embedded ASR1000-RP1 for Cisco ASR 1002 Router Description 6-4
Cisco Embedded ASR1000-SIP10 and SPAs for the Cisco ASR 1002 Router Description 6-4
Cisco ASR1000-ESP5 or ASR1000-ESP10 Description 6-5
Power Supplies in the Cisco ASR 1002 Router 6-6
AC Power Supply for Cisco ASR 1002 Router 6-6
DC Power Supply for Cisco ASR 1002 Router 6-7



Management Ethernet Port Cable Connection 6-27
Connecting a Terminal to the Cisco ASR1000-RP1 Console Port 6-35
Connecting Cables 6-36
CHAPTER 7 Cisco ASR 1000 Series Routers Power Up and Initial Configuration 7-1
Checking Conditions Prior to System Startup 7-1
Verifying Power Supply Operation 7-2
Powering Up the Cisco ASR 1000 Series Routers 7-3
OL-13208-03 vii

Contents
Verifying the Front Panel LEDs 7-7

Verifying the Hardware Configuration 7-7
Checking Hardware and Software Compatibility 7-7
Configuring the Cisco ASR 1000 Series Routers at Startup 7-7

Using the Console Interface 7-8
Configuring Global Parameters 7-8
Checking the Running Configuration Settings 7-9
Saving the Running Configuration to NVRAM 7-10
Power Off the Cisco ASR 1000 Series Router 7-10
CHAPTER 8 Replacing Cisco ASR 1000 Series Routers Field-Replaceable Units 8-1
Removing and Replacing the Cisco ASR 1000 Series RP1 8-1
Removing the Cisco ASR1000-RP1 8-2
Replacing the Cisco ASR1000-RP1 8-2
Removing and Replacing the Cisco ASR 1000 Series RP1 Internal Hard Drive 8-3
Cisco ASR 1000 Series RP1 Spare Hard Drive Accessory Kit 8-3
Removing the Cisco ASR 1000 Series RP1 and Internal Hard Drive from the Cisco ASR 1000 Series
Router 8-4
Replacing the Cisco ASR 1000 Series RP1 Internal Hard Drive 8-8
Removing and Replacing the Cisco ASR 1000 Series RP1 DIMM Memory Module 8-9
Removing and Replacing an eUSB Device 8-13
Removing and Replacing the 1GB USB Flash Token Memory Stick 8-15
Removing and Replacing the Cisco ASR 1000 Series Embedded Service Processors 8-17
Removing a Cisco ASR1000-ESP 8-17
Replacing the Cisco ASR1000-ESP 8-18
Removing and Replacing a SPA Interface Processor 8-19
Electrostatic Discharge Prevention 8-19
Removing a SPA Interface Processor 8-21
Replacing a SPA Interface Processor 8-21
Removing a Shared Port Adapter From a SIP 8-21
Replacing a Shared Port Adapter In a SIP 8-22
Removing and Replacing a Cisco ASR 1006 Router Power Supply 8-22
Removing the AC Power Supply from Cisco ASR 1006 Router 8-23
Replacing the AC Power Supply in Cisco ASR 1006 Router 8-24
Removing and Replacing a DC Power Supply in Cisco ASR 1006 Router 8-25
Removing the DC Power Supply from Cisco ASR 1006 Router 8-26
Replacing the DC Power Supply in Cisco ASR 1006 Router 8-29
viii OL-13208-03

Contents
Removing and Replacing a DC Power Supply in Cisco ASR 1004 Router 8-33
Removing the DC Power Supply From Cisco ASR 1004 Router 8-35
Removing and Installing a DC Power Supply in Cisco ASR 1002 Router 8-43
Removing the DC Power Supply from Cisco ASR 1002 Router 8-45
Repacking the Box 8-48
APPENDIX A Cisco ASR 1000 Series Routers Specifications A-1
Cisco ASR 1006 Router Specifications A-1

Cisco ASR 1006 Router Memory and Storage Options A-2
Cisco ASR 1006 Router Ethernet RJ-45 Port Pinouts A-2
Cisco ASR 1006 Router MGMT Ethernet Port Pinouts A-2
Cisco ASR 1006 Router BITS Port Signals and Pinouts A-3
Cisco ASR 1006 Router Console Port Signals and Pinouts A-3
Cisco ASR 1006 Router Auxiliary Port Signals and Pinouts A-4
Cisco ASR 1006 Router DB-25 Pinout Assignments for Alarm Relays A-4

Cisco ASR 1004 Router MGMT Ethernet Port Signals and Pinouts A-6
Cisco ASR 1004 Router DB-25 Pinout Assignments for Alarm Relays A-8
Cisco ASR 1002 Router MGMT Ethernet Port Signals and Pinouts A-10
OL-13208-03 ix

Contents
APPENDIX B Troubleshooting Initial Startup Problems B-13
Troubleshooting Overview B-13
Online Troubleshooting Resources B-14
General Troubleshooting Tips B-14

Troubleshooting Using a Subsystem Approach B-15
Normal Router Startup Sequence B-15
Troubleshooting the Power Subsystem B-16
Troubleshooting the Cooling Subsystem B-17
Troubleshooting the Shared Port Adapter B-18
Troubleshooting the Upgrade B-19
Replacing or Recovering a Lost Password B-19

Overview of the Password Recovery Procedure B-19
Details of the Password Recovery Procedure B-20
GLOSSARY
INDEX
x OL-13208-03

Preface
This preface discusses the objectives, audience, and organization of the Cisco ASR 1000 Series
Aggregation Services Routers Hardware Installation and Initial Configuration Guide. The following
sections are in this preface:
• Document Revision History, page xi
• Document Objectives, page xii
• Audience, page xii
• Document Organization, page xii
• Safety Warnings and Cautions, page xiii
• Related Documentation, page xviii
• Obtaining Documentation and Submitting a Service Request, page xix
Document Revision History

The Document Revision History table below records technical changes to this document.
Document
Version Date Change Summary
OL-13208-03 November 2008 Improved the two-minute window allotted time to
replace a power supply. You now have up to a maximum
of five minutes to replace the power supply.
OL-13208-02 October 2008 Added Cisco ASR1000-ESP20 and Cisco
ASR1000-ESP10-N support. Updated eUSB device
graphics and replacement information.
OL-13208-01 May 2008 This is the first version of this document for the Cisco
ASR 1000 Series Routers (Cisco ASR1006 Router, Cisco
ASR1004 Router, Cisco ASR1002 Router).
OL-13208-03 xi

Preface
Document Objectives
Document Objectives
This publication describes the installation of the Cisco ASR 1000 Series Aggregation Services Routers,
replacement or upgrading of field-replaceable units (FRUs), and troubleshooting of the Cisco ASR 1000
Series Routers hardware. The purpose of this guide is to enable the safe and efficient installation of the
Cisco ASR 1000 Series Aggregation Services Routers.
Audience
This publication is primarily designed for the person responsible for installing, maintaining, and
troubleshooting the Cisco ASR 1000 Series Aggregation Services Routers. The users of this guide
should:
• Be familiar with electronic circuitry and wiring practices.
• Have experience as electronic or electromechanical technicians.
• Have experience in installing high-end networking equipment. Certain procedures described in this
guide require a certified electrician.
Document Organization
The major sections of this installation and configuration guide are:
Chapter and Appendix Number and Title Description

Preface The preface provides objectives, audience and
organization of this manual.
Chapter 1 Cisco ASR 1000 Series Routers Hardware Overview This chapter provides an overview of the Cisco ASR
1000 Series Aggregation Services Routers.
Chapter 2 Cisco ASR 1000 Series Router Components This chapter describes the components for each Cisco
ASR 1000 Series Aggregation Services Router.
Chapter 3 Preparing Your Site for Installation This chapter provides site preparation guidelines for
installing the ASR 1000 Series Routers.
Chapter 4 Cisco ASR 1006 Router This chapter describes the Cisco ASR 1006 router and
how to install it.
how to install it.
how to install it.
Chapter 7 Cisco ASR 1000 Series Router Power Up and Initial This chapter provides basic system startup and initial
Configuration configuration information.
xii OL-13208-03

Preface
Safety Warnings and Cautions
Chapter and Appendix Number and Title Description

Chapter 8 Replacing the Cisco ASR 1000 Series Routers This chapter provides instructions for removing and
Field-Replaceable Units replacing shared port adapters, ASR 1000 RP1 internal
hard drive, AC and DC power supplies, the Cisco
ASR1000-ESP forwarding processors, the Cisco DIMM
memory card, the Cisco memory stick, and the Cisco
ASR 1000 Series Route Processor 1.
Appendix A Cisco ASR 1000 Series Routers Specifications This appendix provides system specifications and
pinouts.
Appendix B Troubleshooting Initial Startup Problems This appendix provides basic system startup
troubleshooting information.
Listing of Cisco ASR 1000 Series Routers terms with
Glossary definitions.
Index Listing of terms for the Cisco ASR 1000 Series Routers

Most safety warnings for the Cisco ASR 1000 Series Routers are placed in relevant sections throughout
the document. For translated safety warnings, see the Regulatory Compliance and Safety Information for
the Cisco 1000 Series Aggregation Services Routers. Below is Statement 1071, the Warning Definition
statement, complete with translated warnings.
Warning Definition
Warning IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents. Use the statement number provided at the end of
each warning to locate its translation in the translated safety warnings that accompanied this
device. Statement 1071
SAVE THESE INSTRUCTIONS
Waarschuwing BELANGRIJKE VEILIGHEIDSINSTRUCTIES
Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan
veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij
elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard
praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de
waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt
raadplegen.
BEWAAR DEZE INSTRUCTIES
OL-13208-03 xiii

Preface
Varoitus TÄRKEITÄ TURVALLISUUSOHJEITA
Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin
käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu
onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen
mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien
lausuntonumeroiden avulla.
SÄILYTÄ NÄMÄ OHJEET
Attention IMPORTANTES INFORMATIONS DE SÉCURITÉ
Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant
entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez
conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures
couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des
avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil,
référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.
CONSERVEZ CES INFORMATIONS
Warnung WICHTIGE SICHERHEITSHINWEISE
Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen
kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und
den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder
Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten
Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.
BEWAHREN SIE DIESE HINWEISE GUT AUF.
Avvertenza IMPORTANTI ISTRUZIONI SULLA SICUREZZA
Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle
persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli
relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.
Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le
traduzioni delle avvertenze riportate in questo documento.
CONSERVARE QUESTE ISTRUZIONI
Advarsel VIKTIGE SIKKERHETSINSTRUKSJONER
Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du
begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med
elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten
av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne
enheten.
TA VARE PÅ DISSE INSTRUKSJONENE
xiv OL-13208-03

Preface
Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de
lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos
perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de
prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para
localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.
GUARDE ESTAS INSTRUÇÕES
¡Advertencia! INSTRUCCIONES IMPORTANTES DE SEGURIDAD
Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular
cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los
procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el
número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña
a este dispositivo.
GUARDE ESTAS INSTRUCCIONES
Varning! VIKTIGA SÄKERHETSANVISNINGAR
Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.
Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och
känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av
varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna
anordning.
SPARA DESSA ANVISNINGAR
OL-13208-03 xv

Preface
Aviso INSTRUÇÕES IMPORTANTES DE SEGURANÇA
Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões
corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os
circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o
número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de
segurança traduzidos que acompanham o dispositivo.
GUARDE ESTAS INSTRUÇÕES
Advarsel VIGTIGE SIKKERHEDSANVISNINGER
Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for
legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de
involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til
undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de
oversatte advarsler, der fulgte med denne enhed.
GEM DISSE ANVISNINGER
xvi OL-13208-03

Preface
OL-13208-03 xvii

Preface
Related Documentation
Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Related Documentation
Your Cisco ASR1000 Series Routers and the Cisco IOS software running on it contain extensive features
and functionality, which are documented in the following resources:
• All documentation related to the Cisco ASR 1000 Series Routers is listed in the online Cisco ASR
1000 Series Aggregation Services Routers Documentation Roadmap. Information in this master
index includes troubleshooting tools and documentation, regulatory compliance and safety
information, and installation and replacement information. Also see the Cisco ASR 1000 Series Port
Adapter Documentation Roadmap for specific shared port adapters supported on the Cisco
ASR1000 Series routers and the Cisco ASR 1000 Series Routers Troubleshooting Roadmap.
Some of the Cisco ASR1000 Series Routers documentation that is listed on the Cisco ASR 1000
Series Aggregation Services Routers Documentation Roadmap includes:
– The Cisco ASR 1006, ASR 1004, and ASR 1002 Routers Quick Start Guide contain installation
and configuration information. It contains quick reference information about chassis or parts
installation.
– The Cisco ASR 1000 Series Aggregation Services Routers Troubleshooting document contains
information to help you troubleshoot problems with the Cisco ASR1000 Series Routers.
xviii OL-13208-03

Preface
Obtaining Documentation and Submitting a Service Request
– The Regulatory Compliance and Safety Information for Cisco ASR 1000 Series Aggregation
Services Routers document provides international agency compliance, safety, and statutory
information for wide-area network (WAN) interfaces for the Cisco ASR 1000 Series Routers.
– Cisco ASR 1000 Series shared port adapter documentation.
• Cisco IOS software documentation contains Cisco IOS software configuration information and
support. See the modular configuration and modular command reference publications in the set that
corresponds to the software release installed on your Cisco hardware.
• To check the minimum software requirements of Cisco IOS software with the hardware installed on
your router, Cisco maintains the Software Advisor tool on Cisco.com. This tool does not verify
whether modules within a system are compatible, but it does provide the minimum IOS requirements
for individual hardware modules or components.
Note Access to this tool is limited to users with Cisco.com login accounts.
• Cisco Documentation DVD (See the “Obtaining Documentation and Submitting a Service Request”
section on page xix.)

For information on obtaining documentation, submitting a service request, and gathering additional
information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and
revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed
and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free
service and Cisco currently supports RSS version 2.0.
OL-13208-03 xix

Preface
xx OL-13208-03

C H A P T E R 1
Cisco ASR 1000 Series Routers Hardware
Overview
The Cisco ASR 1000 Series Aggregation Services Routers are the next generation midrange router
products. The system is based on Cisco QuantumFlow Processor technology using a family of
Cisco-developed processors.
The Cisco ASR 1000 Series Routers target both enterprise and service provider applications but with
higher performance and improved availability. The specific applications covered by
Cisco ASR 1000 Series Routers are:
• Enterprise applications—Intended as the mid-size aggregation and gateway router typically residing
in a regional or large branch office:
– WAN aggregation at Cisco Enterprise core
– Internet gateway
– Branch or regional office aggregation
– Remote access aggregation
• Service provider applications—Intended as the low-end service provider edge and broadband
aggregation device with similar throughput:
– High-end customer premises equipment (CPE) for business-quality Internet access
– Provider edge (PE) and high-end customer edge (CE) for Layer 2 VPN or Layer 3 VPN services
– Broadband aggregation—PPPoE/PPPoA aggregation and Service Selection Gateway (SSG)
– Low-end Ethernet aggregation
This chapter provides an overview of the Cisco ASR 1000 Series Routers and includes the following
information:
• Cisco ASR 1000 Series Routers, page 1-2
• Cisco ASR 1000 Series Routers Configurations, page 1-32
• Field-Replaceable Units, page 1-4
• Functional Overview, page 1-4
• Cisco Product Identification Standard, page 1-15
Cisco ASR 1000 Series Aggregaion Services Routers Hardware Installation and Initial Configuration Guide
OL-13208-03 1-1

Chapter 1 Cisco ASR 1000 Series Routers Hardware Overview
Cisco ASR 1000 Series Routers
Cisco ASR 1000 Series Routers

The Cisco ASR 1000 Series Aggregation Services Router is Cisco next-generation, modular, highly
services-integrated routing platform designed with the flexibility to support a wide range of packet
forwarding, system bandwidths, performance, and scaling. The overall system architecture is common
across the chassis.
The Cisco ASR 1000 Series consists of three different versions:
• Cisco ASR 1006 Router Description, page 4-1
All three models use the powerful Cisco QuantumFlow Processor which provides performance and
resiliency for network processors.
The Cisco ASR 1000 Series Routers deliver multiple services embedded in the Cisco QuantumFlow
Processor. The services supported on the Cisco Packet QuantumFlow Processor include security services
(for example, encryption and firewall), quality of service (QoS), Network Based Application
Recognition (NBAR), broadband aggregation, and session border controller, among others.
Cisco ASR 1000 Series Routers Features

The Cisco ASR 1000 Series Aggregation Services Routers use different field replaceable units. The
processors are the Cisco ASR 1000 Series Route Processor 1 (RP1), Cisco ASR 1000 Series Embedded
Services Processor (Cisco ASR1000-ESP5, Cisco ASR1000-ESP10, and Cisco ASR1000-ESP20), and
the Cisco ASR 1000 SPA Interface Processor (SIP). The Cisco ASR 1000 ESP is based on Cisco
QuantumFlow Processor technology.
The Cisco ASR 1000 Series Routers contains the following features:
• Online insertion and removal (OIR) capability
• Route processor and embedded services processor redundancy in the Cisco ASR 1000 Series
Routers
• Control processor for ASR 1000 Series SPA Interface Processor
• Control processor for embedded services processors (Cisco ASR1000-ESP5, Cisco
ASR1000-ESP10, or Cisco ASR1000-ESP20)
• 10Gbps and 20Gbps interconnect between Cisco QuantumFlow Processor with redundant Cisco
ASR 1000 Series ESP to mirror data for stateful features
• Power supply redundancy
• Environmental monitoring and reporting functions
• Family of routers using common hardware and software architecture
• Centralized forwarding design (all network traffic passes through one engine)
• Front-to-back airflow—Allows you to mount the router from either front or back into 19-inch
equipment rack
• Supports half-height shared port adapters (HHSPAs) and full-height shared port adapters (FHSPAs)
• Single midplane design (all connectors on one interface midplane)
1-2 OL-13208-03

Cisco ASR 1000 Series Routers Configurations
• One 10/100/1000-Mbps Ethernet Management port—To be used only as a management port; not to
be used as an Ethernet interface port
• Both 25-MHz and 50-MHz shared port adapter operation
• High availability software architecture
The Cisco QuantumFlow Processor processing provides:
• Architecture to address Cisco ASR 1000 Series Router performance, cost, power, and feature
velocity
• Next Generation forwarding and queuing subsystems for Cisco routers to provide data path
acceleration.
The Cisco ASR 1000 Series Router processor system performs the following system management
functions:
• Sending and receiving routing protocol updates
• Managing tables, caches, and buffers
• Monitoring interface and environmental status
• Providing Simple Network Management Protocol (SNMP) management through the console and
Telnet interface
• Accounting for and switching of data traffic
• Booting and reloading images
Cisco ASR 1000 Series Routers Configurations

The Cisco ASR 1000 Series Routers consist of a number of packaging configurations. The chassis
configurations are modular with separate field-replaceable units (FRUs) for the Cisco ASR 1000 Series
Route Processor 1 (RP1), the Cisco ASR 1000 Series Embedded Services Processor (ESP5, ESP10, and
ESP20), and the shared port adapters.
With the exception of the Cisco ASR 1002 Router, all FRUs (Cisco ASR 1000 Series Route Processor 1,
Cisco ASR 1000 Series Embedded Services Processor, and SPAs) are designed to work in the different
chassis models. (The Cisco ASR1000-ESP20 is not supported in the Cisco ASR 1002 Router.) The
power supplies and fan modules are chassis specific. The SPAs are supported in all chassis
configurations although there are SPA restrictions in the Cisco ASR 1002 Router.
Table 1-1 lists the Cisco ASR 1000 Series Routers orderable configurations.
Table 1-1 Cisco ASR 1000 Series Routers Configurations
Number of
I/O Card Maximum SPAs Redundant RP1 Redundant ESP Redundant Power
Chassis Slots Supported Option Option Supply Option
Cisco ASR 3 12 HH Yes Yes 1+1
1006
Cisco ASR 2 8 HH No No 1+1
1004
Cisco ASR 0 3 HH (1 built-in No No 1+1
1002 4x1GE)
OL-13208-03 1-3

Field-Replaceable Units
The Cisco ASR 1000 Series routers are easy to service; many of their major components are
field-replaceable units (FRUs). The following is a list of the Cisco ASR 1000 Series Routers FRUs:
• Cisco ASR 1000 Series Route Processor 1 (RP1)
• Cisco ASR 1000 Series Embedded Services Processors (Cisco ASR1000-ESP5, Cisco
ASR1000-ESP10, Cisco ASR1000-ESP20)
• Shared port adapters
• Cisco ASR 1000 Series SIP (shared port adapter interface processor)
• Cisco ASR 1000 Series RP1 internal hard drive
• Cisco ASR 1000 Series RP1 DIMM memory module (Note that the Cisco embedded ASR1000-RP1
on the Cisco ASR 1002 Router DIMM memory module is not field-replaceable.)
• USB Flash Token Memory Stick
• AC and DC power supplies
• Bracket kit—Custom cable-management brackets mount to each rack-mount bracket to provide
cable-management to both sides of the chassis (parallel with card orientation). These brackets are
screw-mounted to the rack brackets to allow easy installation and removal. There is a rack-mount
bracket for each chassis:
– Cisco ASR 1006 cable-management brackets contain 5 independent cable-management
U-features to provide cable dressing of each card module slot. For SIPs, these brackets work in
tandem with SPA product feature cable-management to allow installation and removal of
adjacent cards without the need to remove cables.
– Cisco ASR 1004 cable-management brackets contain three independent cable-management
U-features to provide cable dressing of each card module slot. For SIPs, these brackets work in
tandem with SPA product feature cable-management to allow installation and removal of
adjacent cards without the need to remove cables.
– Cisco ASR 1002 cable-management brackets contains one independent cable-management
U-features to provide cable dressing of each card module slot. These brackets work in tandem
with SPA product feature cable-management to allow installation and removal of adjacent cards
without the need to remove cables
Functional Overview
This section contains the following topics:
• Chassis Slot and Logical Interface Numbering, page 1-5
• MAC Address Information, page 1-8
• Online Insertion and Removal, page 1-9
• Environmental Monitoring and Reporting Functions, page 1-10
1-4 OL-13208-03

Functional Overview
Chassis Slot and Logical Interface Numbering

The Cisco ASR 1000 Series Routers have a slot numbering system located on both sides of the card
module location. The chassis slots are physically numbered from zero starting at the bottom of the
chassis. This section describes the slot numbering for the Cisco ASR 1000 Series Routers:
• Cisco ASR 1006 Router Slot Numbering, page 1-5
Cisco ASR 1000 Series SPA Interface Processor (SIP) subslots begin their numbering with “0” and have
a horizontal orientation. The SIP subslot numbering is indicated by a small numeric label beside the
subslot on the faceplate. Some commands allow you to display information about the SPA itself, such as
show idprom module and show hw-module subslot. These commands require you to specify both the
physical location of the SIP and SPA in the format, Slot/Subslot, where:
• Slot—Specifies the chassis slot number in the Cisco ASR 1000 Series Routers where the SIP is
installed.
• Subslot—Specifies a subslot of the SIP where the SPA is installed.
Cisco ASR 1006 Router Slot Numbering

The Cisco ASR 1006 Router is designed with each slot numbered as shown in Figure 1-1.
OL-13208-03 1-5

Functional Overview
Figure 1-1 Cisco ASR 1006 Router — Slot Numbering
A /L C/A
0
7
A /L C/A
2
A /L C/A
6
A/L C/A
1
A/L C/A
5
A /L C/A
0
0
4 PWR
STAT
ACTV
STBY
F1 ASR1000-ESP10
3 PWR
STAT
ACTV
STBY
F0 ASR1000-ESP10
CRIT
PWR ACTV MAJ
2
O
AC
STAT STBY MIN
R1 ASR1000-RP1
CRIT
PWR ACTV MAJ
1 STAT STBY MIN
AC
O
280033
R0 ASR1000-RP1
1 Slot RP0 with ASR 1000 Series RP1 5 ASR 1000 Series SIP slot 0
3 Slot FP0 with ASR 1000 Series ESP 7 ASR 1000 Series SIP slot 2
4 Slot FP1 with ASR 1000 Series ESP
The Cisco ASR 1006 Router contains three Cisco ASR 1000 Series SPA Interface (SIP) supports four
subslots for the installation of SPAs.
1-6 OL-13208-03

Functional Overview
Figure 1-2 shows the Cisco ASR 1006 Router SPA subslot location.
Figure 1-2 Cisco ASR 1006 Router — ASR1000-SIP10 Subslots
Front of SIP, horizontal chassis slots
SPA 0 SPA 1
231508
SPA 2 SPA 3

The Cisco ASR 1004 Router contains two Cisco ASR 1000 Series SPA Interface Processors (SIPs) and
supports four subslots for the installation of SPAs.
Figure 1-3 shows the Cisco ASR 1004 Router with modules and filler plates installed.
Figure 1-3 Cisco ASR 1004 Router —Front and Side View
6 7
5 8
US
A
C/
AT
ST
A
A/L
C/
A
A/L
C/
SPA-4XOC3-POS
A/L
C/
3
A/L
US
A
C/
AT
1
ST
A
A/L
C/
0
A
US
A/L
A
C/
C/
SPA-4XOC3-POS
AT
A
ST
A/L
A
C/
A/L
C/
3
A/L
A
A/L
C/
SPA-4XOC3-POS
2
A
A/L
C/
1
3
A/L
US
A
2
US
A
C/
C/
AT
AT
ST
A
1
ST
A
A/L
A/L
C/
C/
A
0
A/L
A/L
C/
C/
4
SPA-4XOC3-POS SPA-4XOC3-POS
A
A
A/L
A/L
C/
C/
3
3
A/L
A/L
US
A
2
C/
AT
1
ST
A
1
A/L
C/
0
A
0
US
A/L
A
C/
C/
SPA-4XOC3-POS
AT
A
ST
A/L
A
C/
A/L
C/
3
A/L
A
A/L
C/
SPA-4XOC3-POS
2
A
A/L
C/
1
3
A/L
0
2
US
A
C/
AT
1
ST
A
A/L
C/
0
A/L
C/
SPA-4XOC3-POS
3
A
A/L
C/
3
A/L
2
1
0
2 HD CARRIER
BITS
LINK
MGMT ETHERNE
T
CON
AUX
USB
CRIT
ACTV MAJ
DF 280312
O
AC
PWR DISK
1
1
STBY MIN 0
STAT
P1
ASR1000-R
1 Slot RP0 with ASR 1000 Series RP1 5 SPA subslot 2

2 Slot FP0 with ASR 1000 Series ESP10 6 SPA subslot 0
3 ASR 1000 Series SIP slot 0 7 SPA subslot 1

The Cisco ASR 1002 Router contains one Cisco embedded ASR1002 -RP1 which is addressed as R0 and
one Cisco ASR1000-ESP5 or ASR1000-ESP10 forwarding processor in slot F0. The Cisco ASR 1002
Router consists of an embedded ASR1000-RP1 and embedded ASR1000-SIP10 board supporting three
half-height SPAs or 1half-height and one full-height SPA and one Cisco ASR1000-ESP5 forwarding
processor.
OL-13208-03 1-7

Functional Overview
The SPA bays are bay 1, bay 2, and bay 3. The built-in 4xGE SPA ports are located in the SPA 0 location
and will be addressed as GE 0/0/x. The Cisco ASR 1002 Router provides a built-in 4-Gigabit Ethernet
interface and this SPA is physically located on the Cisco embedded ASR1000-RP1 board. The Cisco
ASR 1000 Series ESP card is located in slot 1 and labeled as FP0.
Figure 1-4 Cisco ASR 1002 Router Slot Numbering
1 3
PWR ACTV
STAT STBY
ASR1000-ESP10
ASR 1002 STAT QE0 QE1 QE2 QE3 BOOT CARRIER LINK PWR STAT
C/A
C/A
C/A
C/A
pwr min
US
AT
A/L
A/L
A/L
A/L
ST
stat maj
SPA-4XOC3-POS
crit
280369
C/A
C/A
C/A
C/A
C/A
C/A
C/A
C/A
US
US
AT
AT
A/L
A/L
A/L
A/L
A/L
A/L
A/L
A/L
ST
ST
0
3
2 4
1 Embedded route processor RP0 in subslot 0 3 Cisco SPA subslot 1

2 Cisco SPA subslot 2 4 Cisco SPA subslot 3
MAC Address Information

The Media Access Control (MAC) or hardware address is a standardized data link layer address that is
required for certain network interface types. These addresses are specific and unique to each port and
are not used by other devices in the network. The Cisco ASR 1000 Series Routers assign and control the
MAC addresses of its shared port adapters.
You can identify shared port adapter slots by using software commands. To display information about:
• All shared port adapter slots, use the show interfaces command.
• A specific shared port adapter slot, use the show interfaces command with the shared port adapter
type and slot number in the format show interfaces port-adapter-type slot-number/port-number.
Note If you abbreviate the command (sh int) and do not specify shared port adapter type and slot number (or
arguments), the system interprets the command as show interfaces and displays the status of all shared
port adapters and ports.
The MAC addresses are assigned to the slots in sequence. For example, in the Cisco ASR 1006 Router,
the first address is assigned to slot 0 and the last address is assigned to slot 6. The actual MAC address
assignment is 16 MAC addresses per SPA slot for half-height SPAs and 64 per SPA slot for full-height
SPAs. Also, the Cisco ASR 1000 Series RP1 RP Management Ethernet port is assigned one MAC
address from the end of the pool and for a Cisco ASR 1006 Router with two Cisco ASR 1000 RP1s, each
ASR10000 RP1 is assigned one MAC address.
Using this address scheme, you can remove shared port adapters and insert them into other routers
without causing the MAC addresses to move around the network or be assigned to multiple devices.
1-8 OL-13208-03

Functional Overview
If the MAC addresses were stored on each shared port adapter, online insertion and removal would not
function because you could never replace one shared port adapter with an identical one; the MAC
addresses would always be different. Also, each time a shared port adapter was replaced, other devices
on the network would have to update their data structures with the new address. If the other devices did
not update quickly enough, the same MAC address could appear in more than one device at the same
time.
Note Storing the MAC addresses for every slot in one central location means the addresses stay with the
memory device on which they are stored.
Online Insertion and Removal

In the modular chassis configurations, most Cisco ASR 1000 Series Router field-replaceable units
(FRUs) support online insertion and removal (OIR). However, the removal of critical non-redundant
FRUs will result in service interruption.
Note As you disengage the shared port adapter from the router, online insertion and removal (OIR)
administratively shuts down all active interfaces in the shared port adapter.
Online insertion and removal (OIR) allows you to install and replace shared port adapters while the
router is operating; you do not need to notify the software or shut down the system power, although you
should not run traffic through the shared port adapter you are removing while it is being removed. Online
insertion and removal is a method that is seamless to end users on the network, maintains all routing
information, and preserves sessions.
All SPA OIR events are independent of one another. An OIR event of a single SPA does not affect the
other SPAs in that ASR1000-SIP10 or any other system function.
Note The Cisco ASR 1002 Router differs from the Cisco ASR 1006 and Cisco ASR 1004 routers. The Cisco
ASR 1002 Router supports the Cisco embedded ASR1000-RP1 which is a combined route processor and
carrier card which are not field-replaceable units. The Cisco ASR1000-ESP5 or ASR1000-ESP10 are
field-replaceable units.
The following is a functional description of OIR for background information only; for specific
procedures for installing and replacing a shared port adapter in Cisco ASR 1000 Series Routers, refer to
the online configuration note for each shared port adapter.
When you remove or insert a shared port adapter in a Cisco ASR 1000 Series Router, the Control
Processor notifies the Cisco ASR1000-RP1, which in turn notifies the forwarding engine control
processor (FECP), and then performs as follows:
• Rapidly scans the midplane for configuration changes.
• Initializes all newly inserted shared port adapters, noting any removed interfaces and placing them
in the administratively shutdown state.
• Brings all previously configured interfaces on the shared port adapter back to the state they were in
when they were removed. Any newly inserted interfaces are put in the administratively shutdown
state, as if they were present (but not configured) at boot time. If a similar shared port adapter type
is reinserted into a slot, its ports are configured and brought online up to the port count of the
original SPA.
OL-13208-03 1-9

Functional Overview
Environmental Monitoring and Reporting Functions

Environmental monitoring and reporting functions allow you to maintain normal system operation by
identifying and resolving adverse conditions prior to loss of operation.
Caution To prevent overheating the chassis, ensure that your system is drawing cool inlet air. Over temperature
conditions can occur if the system is drawing in the exhaust air of other equipment. Ensure adequate
clearance around the sides of the chassis so that cooling air can flow through the chassis interior
unimpeded and exhaust air exits the chassis and is not drawn into the inlet vent of another device.
Environmental Monitoring
The environmental monitoring functions use sensors to monitor the temperature of the cooling air as it
moves through the chassis.
The local power supplies provide the ability to monitor:
• Input and output voltage
• Output current
• Outlet temperature
The router is expected to meet the following environmental operating conditions:
• Operating Temperature Nominal: 5° to 40°C
• Operating Temperature Short Term: 5° to 55°C
• Operating Humidity Nominal: 5% to 85% non-condensing
• Operating Humidity Short Term: 5% to 90% non-condensing
• Operating Altitude: 198 to 13,200 feet (60 to 4000 meters)
• DC Input Range: –40.5 to –72 VDC
• AC Input Range: 85 to 264 VAC
If the air temperature exceeds a defined threshold, the system controller displays warning messages on
the console terminal, and if the temperature exceeds the shutdown threshold, the system controller shuts
down the system.
In addition, the power supplies monitor internal power supply temperatures and voltages. A power
supply is either within tolerance (normal) or out of tolerance (critical). If an internal power supply
temperature or voltage reaches a critical level, the power supply shuts down without any interaction with
the system processor.
The environmental monitoring functions use the following levels of status conditions to monitor the
system:
• Normal—All monitored parameters are within normal tolerances.
• Warning—The system has exceeded a specified threshold. The system continues to operate, but
operator action is recommended to bring the system back to a normal state.
• Critical—An out-of-tolerance temperature or voltage condition exists. The system continues to
operate; however, the system is approaching shutdown. Immediate operator action is required.
1-10 OL-13208-03

Functional Overview
• Shutdown—The processor has detected a temperature condition that could result in physical damage
to system components and has disabled DC power to all internal components. This condition
requires immediate operator action. All DC power remains disabled until you toggle the power
switch. Before any shutdown, the system logs the status of monitored parameters in NVRAM so you
can retrieve it later to help determine the cause of the problem.
• Power supply shutdown—The power supply detected an internal out-of-tolerance overvoltage,
overcurrent, or temperature condition and shut itself down. All DC power remains disabled until you
toggle the power switch.
Fan Failures
When the system power is on, all fans should be operational. The system continues to operate if a fan
fails. When a fan fails, the system displays the following message:
router: 00:03:46:%ENVM-3-BLOWER:Fan 2 may have failed
If the air temperature exceeds a defined threshold, the system controller displays warning messages on
the console terminal, and if the temperature exceeds the shutdown threshold, the system controller shuts
down the system.
If the system does shut down because the temperature exceeded the shutdown threshold, the system
displays the following message on the console screen and in the environment display when the system
restarts:
Queued messages:
%ENVM-1-SHUTDOWN: Environmental Monitor initiated shutdown
Reporting Functions
The chassis manager on the forwarding engine control processor manages the local resources of the
forwarding processor. It manages the ESI (Enhanced Serdes Interconnect) which are the datapath links
on the midplane connecting the Cisco ASR 1000 Series RP1s, SIPs, and standby ESP modules to the
active Cisco ASR 1000 Series Embedded Services Processor. It communicates with the chassis manager
on the Cisco ASR 1000 Series Route Processor 1 to report the status and health, including detected
hardware failures, ESI status, software process status, and the state of thermal sensors.
The Cisco ASR 1000 Series Routers display warning messages on the console if chassis
interface-monitored parameters exceed a desired threshold. You can also retrieve and display
environmental status reports with the show environment all, show version, show inventory, show
platform, and show diag commands. Parameters are measured and reporting functions are updated
every 60 seconds. A brief description of each of these commands follows.
Note The example outputs displayed in this section are from a Cisco ASR 1004 Router. Similar output
displays for all Cisco ASR 1000 series routers.
OL-13208-03 1-11

Functional Overview
Example 1-1 Show Environment All Command
Router#show environment
% Incomplete command.
Router#show environment all

Sensor List: Environmental Monitoring
Sensor Location State Reading
V1: VMA F0 Normal 1791 mV
V1: VMB F0 Normal 1196 mV
V1: VMC F0 Normal 1191 mV
V1: VMD F0 Normal 1093 mV
V1: VME F0 Normal 996 mV
V1: 12v F0 Normal 11894 mV
V1: VDD F0 Normal 3261 mV
V1: GP1 F0 Normal 900 mV
V2: VMA F0 Normal 3286 mV
V2: VMB F0 Normal 2495 mV
V2: VMC F0 10% high 1796 mV
V2: VMD F0 Normal 1093 mV
V2: VME F0 Normal 996 mV
V2: VMF F0 Normal 996 mV
V2: 12v F0 Normal 11850 mV
V2: VDD F0 Normal 3261 mV
V2: GP1 F0 10% high 898 mV
Temp: Inlet F0 Normal 29 Celsius
Temp: Asic1 F0 Normal 47 Celsius
Temp: Exhaust1 F0 Normal 36 Celsius
Temp: Exhaust2 F0 Normal 36 Celsius
Temp: Asic2 F0 Normal 43 Celsius
V1: VMA 0 Normal 1093 mV
V1: VMB 0 Normal 1196 mV
V1: VMC 0 Normal 1494 mV
V1: VMD 0 Normal 1791 mV
V1: VME 0 Normal 2490 mV
V1: VMF 0 Normal 3291 mV
V1: 12v 0 Normal 11894 mV
V1: VDD 0 Normal 3266 mV
V1: GP1 0 Normal 747 mV
V2: VMA 0 20% low 0 mV
V2: VMB 0 Normal 1201 mV
V2: VMC 0 20% low 0 mV
V2: VMD 0 20% low 0 mV
V2: VME 0 20% low 0 mV
V2: VMF 0 20% low 0 mV
V2: 12v 0 Normal 11909 mV
V2: VDD 0 Normal 3271 mV
Temp: Left 0 Normal 25 Celsius
Temp: Center 0 Normal 26 Celsius
Temp: Asic1 0 Normal 36 Celsius
Temp: Right 0 Normal 23 Celsius
PEM Iout P0 Normal 17 A
PEM Vout P0 Normal 12 V AC
PEM Vin P0 Normal 115 V AC
Temp: PEM P0 Normal 27 Celsius
Temp: FC P0 Fan Speed 65% 26 Celsius
Temp: FM P1 Normal 24 Celsius
Temp: FC P1 Fan Speed 65% 26 Celsius
V1: VMA R0 Normal 1098 mV
V1: VMB R0 Normal 3295 mV
V1: VMC R0 Normal 2495 mV
1-12 OL-13208-03

Functional Overview
V1: VMD R0 Normal 1791 mV

V1: VME R0 Normal 1499 mV
V1: VMF R0 Normal 1201 mV
V1: 12v R0 Normal 11938 mV
V1: VDD R0 Normal 3261 mV
V1: GP1 R0 Normal 903 mV
V1: GP2 R0 Normal 1242 mV
Temp: CPU R0 Normal 33 Celsius
Temp: Outlet R0 Normal 32 Celsius
Temp: Inlet R0 Normal 26 Celsius
Temp: Asic1 R0 Normal 32 Celsius
Example 1-2 Show Version Command
The show version command displays the system hardware configuration, software version, and names
and sources of configuration files and boot images.
Following is sample output of the show version command:
Router# show version
Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version
12.2(33)XNA, RELEASE SOFTWARE
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Thu 01-May-08 00:29 by mcpre
Cisco IOS-XE software, Copyright (c) 1986-2008 by Cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are

licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to

[email protected].
cisco ASR1004 (RP1) processor with 757182K/6147K bytes of memory.

2 Packet over SONET interfaces
32768K bytes of non-volatile configuration memory.
2097152K bytes of physical memory.
439807K bytes of eUSB flash at bootflash:.
39004543K bytes of SATA hard disk at harddisk:.
Configuration register is 0x0
Example 1-3 Show Inventory Command
The show inventory command displays an extended report that includes the product inventory listing of
all Cisco products installed in the networking device.
Following is sample output of the show inventory command:
Router#show inventory
NAME: "Chassis", DESCR: "Cisco ASR1004 Chassis"
OL-13208-03 1-13

Functional Overview
PID: ASR1004 , VID: V00, SN:
NAME: "module 0", DESCR: "Cisco ASR1000 SPA Interface Processor 10"
PID: MCP-CC , VID: V00, SN: JAB1104064G
NAME: "SPA subslot 0/1", DESCR: "2-port OC3/STM1 POS Shared Port Adapter"
PID: SPA-2XOC3-POS , VID: V01, SN: JAB1006095Z
NAME: "subslot 0/1 transceiver 0", DESCR: "OC3 SR-1/STM1 MM"

PID: N/A , VID: , SN: 2008692
NAME: "SPA subslot 0/2", DESCR: "4-port T3/E3 Serial Shared Port Adapter"
PID: SPA-4XT3/E3 , VID: V01, SN: JAB09210247
NAME: "module R0", DESCR: "Cisco ASR1000 Route Processor 1"

PID: ASR1000-RP1 , VID: V00, SN: JAB110200CQ
NAME: "module F0", DESCR: "Cisco ASR1000 Embedded Services Processor, 10Gbps"
PID: ASR1000-ESP10 , VID: V00, SN: JAB111101A1
NAME: "Power Supply Module 0", DESCR: "Cisco ASR1004 AC Power Supply"
PID: ASR1004-PWR-AC , VID: V00, SN: ART1103K00C
NAME: "Fan Module 1", DESCR: "Cisco ASR1004 Fan Module"

PID: ASR1004-FAN , VID: V00, SN: ART1052L01U
Example 1-4 Show Platform Command
The show platform command displays the output of the current wait policy for each type of connection,
as well as any information on the currently configured banners.
Following is sample output of the show platform command:
Router#show platform
Chassis type: ASR1004
Slot Type State Insert time (ago)

--------- ------------------- --------------------- -----------------
0 MCP-CC ok 16:20:27
0/1 SPA-2XOC3-POS ok 16:18:49
0/2 SPA-4XT3/E3 ok 16:18:56
R0 ASR1000-RP1 ok, active 16:20:27
F0 ASR1000-ESP10 ok, active 16:20:27
P0 ASR1004-PWR-AC ok 16:19:27
P1 ASR1004-FAN ok 16:19:27
Slot CPLD Version Firmware Version

--------- ------------------- ---------------------------------------
0 07091401 12.2(33r)XN1
R0 0706210B 12.2(33r)XN1
F0 07051650 12.2(33r)XN1
Example 1-5 Show Diag Command
The show diag slot R0 eeprom detail command displays the configuration hardware information
including DRAM and Static RAM (SRAM) on line cards. To display more details than the normal show
diag command output, use show diag [slot-number] [details].
Following is sample output of the show diag slot R0 eeprom detail command:
1-14 OL-13208-03

Cisco Product Identification Standard
Router#show diag slot R0 eeprom detail

Slot R0 EEPROM data:
EEPROM version : 4
Compatible Type : 0xFF
Controller Type : 1460
Hardware Revision : 4.7
PCB Part Number : 73-10253-04
Board Revision : 03
Deviation Number : 0-0
Fab Version : 04
PCB Serial Number : JAB110200CQ
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Top Assy. Part Number : 68-2625-04
Product Identifier (PID) : ASR1000-RP1
CLEI Code : UNASSIGNED
Version Identifier (VID) : V00
Manufacturing Test Data : 00 00 00 00 00 00 00 00
Field Diagnostics Data : 00 00 00 00 00 00 00 00
Asset ID : AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA

This section describes the Cisco products and services product identification standard. This feature
provides you with the ability to effectively integrate and manage Cisco products in your network and
business operations.
OL-13208-03 1-15

Unique Device Identifier

The Unique Device Identifier (UDI) is the Cisco product identification standard for hardware products.
A product identification standard removes barriers to enterprise automation and can help you reduce
operating expenses.
The UDI provides a consistent electronic, physical, and associated business-to-business information
product identification standard.
The UDI is a combination of five data elements. Table 1-2 lists the UDI elements.
Table 1-2 Cisco UDI Elements
Electronic Physical
UDI Data Element Visibility Visibility Description
PID Yes Yes Product ID, also known as product name, model
name, product number
VID Yes Yes Version ID
SN Yes Yes Serial number, the unique instance of the PID (see
Figure 1-5, Figure 1-7, and Figure 1-6 in the next
section for location of the serial number label)
Entity Name Yes No Type, such as chassis, slot, or power supply
Product Description Yes No Additional product information
The combination of serial number and product ID (PID) is unique and consistent across all Cisco
products. The PID that is coded on hardware is called a base product identifier.
Additional orderable PIDs may be associated to a base PID. For instance, an orderable PID may describe
a packaging configuration for a product or a bundled group of products sold, tested, and shipped
together. Specific unique device identifier (UDI) benefits include the following:
• Identifies:
– Individual Cisco products in your networks
– PIDs and SNs for service and replaceable products
– VIDs for product version visibility
• Facilitates discovery of products subject to recall or upgrade
• Enhances inventory automation of Cisco products
The Cisco product identification standard provides the following features:
• Version visibility—Cisco continuously improves products through feature additions. Product
changes are indicated by incrementing the version ID (VID), which provides version visibility to
help you understand and manage product changes. The VID management ensures consistency of
changes from product to product.
• Operating expense reduction— The Cisco UDI provides accurate and detailed network inventory
information; identifying each Cisco product in a network element through a standard interface.
Cisco operating systems can view and use this data, allowing you to automate your electronic
inventory.
1-16 OL-13208-03

• Consistency across product layers—The UDI is designed into hardware products and cannot
overwritten in error. Operating and management systems discover the UDI through standard
interfaces and display the UDI in standard outputs. Standard interfaces include the IETF standard
ENTITY-MIB.
Note Go to the following URL for complete information on the product identification standard:
http://www.cisco.com/go/udi/
Serial Number Label Location

This section contains graphics of each chassis showing the location of the serial number label.
OL-13208-03 1-17

Figure 1-5 shows the serial number location for the Cisco ASR 1006 Router.
Figure 1-5 Cisco ASR 1006 Router Serial Number Label Location
280157, 781-00578-01
SN: XXXNNNNXXXX
1-18 OL-13208-03

Figure 1-6 shows the serial number label location for the Cisco ASR 1004 Router.
202416, 781-00564-01
SN: XXXNNNNXXXX
OL-13208-03 1-19

Figure 1-7 shows the serial number label location for the Cisco ASR 1002 Router.
280158, 781-00579-01
SN: XXXNNNNXXXX
1-20 OL-13208-03

C H A P T E R 2
Cisco ASR 1000 Series Routers Components
The Cisco ASR 1000 Series Routers contain the following components:
• Cisco ASR 1000 Series Route Processor, page 2-1
• Cisco ASR 1000 Series Embedded Services Processors, page 2-9
• Cisco ASR 1000 Series SPA Interface Processor, page 2-13
• Cisco ASR 1000 Series Router Power Supplies, page 2-16
Note Throughout this document, the term slot refers to a Cisco ASR 1000 Series Router chassis slot. The
Cisco ASR 1000 Series Route Processor 1, Cisco ASR 1000 Series Embedded Services Processor, and
Cisco ASR 1000 Series SPA Interface Processor (SIP), and power supplies plug into these slots. Shared
port adapters plug into SIP bays.
Cisco ASR 1000 Series Route Processor

The Cisco ASR 1000 Series Route processor is the central network clocking card and runs the network
operating system, BINOS kernel plus IOSD (IOS daemon). The Cisco ASR1000-RP1 is responsible for:
• Selection of the active Cisco ASR 1000 Series Route Processor and the Cisco ASR 1000 Series
Embedded Services Processor and notification of the Cisco ASR 1000 Series SPA Interface
Processor of these events.
• All the control processors communicating and performing packet processing on packets punted to it
by the Cisco ASR 1000 Series Embedded Services Processors (ESP).
The Cisco ASR 1000-RP1 has LED status indicators, an RJ-45 plug for DTI and BITS timing reference,
and two USB ports which can be used with smart cards for secure key distribution.
Specific system tasks performed by the Cisco ASR 1000 Series Route Processor include the following:
• Runs the router control plane, including network control packets, and connection setup
• User interfaces: 10/100/1000 Management Ethernet, CON/AUX, USB
• Active and standby Cisco ASR 1000 Series RP1 and Cisco ASR 1000 Series Embedded Services
Processor master and standby synchronization (Tasks include switchover from failing master to
standby.)
• Code storage, management, and upgrade.
OL-13208-03 2-1

Chapter 2 Cisco ASR 1000 Series Routers Components
• Downloading operational code for SIPs and Cisco ASR 1000 Series Embedded Services Processor
over Ethernet out of band channel (EOBC), which is used for communication between the control
processors on the Cisco ASR 1000 Series Routers
• Command line interface (CLI), alarm, network management, logging, and statistics aggregation
• Chassis management
• Ethernet out-of-band management
• Punt path processing for packets not supported by the embedded services processors
Cisco ASR 1000 Series Route Processor Features

The Cisco ASR1000-RP1 route processors receive and transmit all network packets through the active
embedded services processors. The Cisco ASR1000-RP1:
• Provides a configuration repository along with a hard disk drive (optionally a solid-state drive) for
logging system statistics, records, events, errors, and dumps (for both the Cisco ASR 1006 Router
and Cisco ASR 1004 Router).
• Provides the management interfaces of the platform including Dual Asynchronous
Receiver/Transmitter (DUART) that is used for the CON and AUX serial ports. The MGMT Ethernet
(ENET) management ports, CLI, status indicators, BITS interface, reset switch, Audible Cutoff
(ACO) button, and USB ports for secure keys.
• Provides chassis management (environmental)
• Is a field-replaceable units (FRU) with online insertion and removal (OIR)., except for the built-in
RP1 on the Cisco ASR1002 router
• Provides non-volatile storage for the system used as the image and configuration repository along
with the logger for system statistics, records, events, errors, and dumps.
• Is responsible for the chassis management including activation and initialization of the other cards,
selection or switchover of active versus standby cards, image management and distribution, logging
facilities, distribution of user configuration information, and alarm control.
• Provides control signals and Ethernet out of band channel (EOBC) for the two Cisco ASR 1000
Series Embedded Services Processors and one other Cisco ASR 1000 Series Route Processor 1.
• Includes control signals for monitoring the health of power entry modules, shutting down the power
and driving alarm relays located on the power entry modules.
• The Cisco ASR 1000 Series RP1 module can be configured with either a 40 GB or a 32 GB disk.
The Cisco ASR 1000 Series route processor module consists of a front panel label for indicator and
control functions and a separate label for the I/O connectors. The Cisco ASR1000-RP1 model number
labeling is located next to the left card module handle. The modules also contain card handles to assist
in insertion or removal of the module.
2-2 OL-13208-03

Figure 2-1 shows the Cisco ASR 1000 Series Route Processor faceplate.
Figure 2-1 Cisco ASR Series 1000 Route Processor Faceplate LEDs and Connectors
1
CRIT HD
PWR ACTV MAJ O USB 2
AC
STAT STBY MIN BF
ASR1000-RP1 0 1 DISK
3
280078
5 4
1 Internal hard drive LED 4 USB 0, USB 1 connector

2 External USB Flash LED 5 ASR1000 RP1 LEDs
3 Internal USB bootflash LED
Figure 2-2 shows the Cisco ASR1000-RP1 with faceplate connectors.
Figure 2-2 Cisco ASR Series 1000 Route Processor Connectors
1 2 3 4 5 6
CARRIER LINK
BITS MGMT ETHERNET CON AUX
280079
1 CARRIER LED 4 MGMT Ethernet connector

2 BITS connector 5 CON connector
3 LINK LED 6 AUX connector
OL-13208-03 2-3

Table 2-1 lists the Cisco ASR 1000 Series Route Processor LEDs and behaviors.
Table 2-1 Cisco ASR 1000 Series Route Processor LEDs
LED Label LED Color —State Behavior Description

PWR Power Solid green All power requirements are within
specification
Off Off, the router is in standby mode.
STAT System status Solid green Cisco IOS software has successfully
booted.
Yellow BootROM has successfully loaded.
Red System failure or during boot process.
ACTV Active Green Lit when the Cisco ASR 1000 Series RP1
is active.
STBY Standby Yellow Lit when the Cisco ASR1000 Series RP1 is
the standby processor.
CRIT Critical Solid Red Critical alarm indicator or during boot
process. An example: the ambient air tem-
perature is above 60ºC and will begin
shutdown in 5 minutes.
MAJ Major Solid Red Major alarm indicator. For example:
Ambient air temperature is beyond short
term operating range of 55ºC. System will
shut down above 60ºC.
MIN Minor Amber Minor alarm indicator. Ambient air tem-
perature is beyond normal operating range
of 40ºC. For example: if the RP software
determines that an unknown card has been
installed or if the card has failed, the card
can power it off or set a minor alarm.
DISK HD Internal hard drive Flashing Green Activity indicator.
LED Off No activity.
DISK USB External USB Flash Flashing Green Activity indicator.
LED Off No activity.
DISK BF Internal USB Flashing Green Activity indicator.
bootflash LED Off No activity.
CARRIER LED Off Out of service or not configured.
Solid Green In frame and working properly.
Amber Fault or loop condition exists.
LINK 10/100/1000 RJ-45 Solid Green Link with no activity.
Interface LED Flashing Green Link with Activity.
Off No link.
2-4 OL-13208-03

How the Cisco ASR1000-RP1 Alarm LEDs Work

The Cisco ASR1000-RP1 faceplate displays the CRIT, MAJ, and MIN alarm indicator LEDs. A female
DB-25 connector on the power supply faceplate enables you to attach an external alarm monitoring
facility to the router. See Cisco ASR 1006 Router DB-25 Pinout Assignments for Alarm Relays, page
A-4.
The alarm signals sent to this DB-25 connector are identical in function to those sent to the system LEDs
on the Cisco ASR1000-RP1. Each alarm consists of three contact pins that are switched when an alarm
becomes active which causes a corresponding contact closure between the DB-25 connector pins.
Thus, a critical, major, or minor alarm condition detected in the router can trigger a simultaneous fault
indication in some of the following ways:
• System alarm LEDs—The three system alarm LEDs on the Cisco ASR1000-RP1 faceplate
constitute the standard method of alarm notification in the router. These LEDs indicate router status
at all times, but you must directly observe these LEDs to become aware of a router alarm condition.
• External alarm monitoring facility—By equipping your router with a telco-style external alarm
monitoring facility, you can provide a more physical indication of router status. A visual alarm,
however, can be reset only by resolving the problem that caused the alarm condition.
For example, the same alarm signal that illuminates one of the three system alarm LEDs on the Cisco
ASR1000-RP1 faceplate for a critical, major, or minor alarm condition is also sent to the DB-25
connector by means of an associated alarm relay in the Cisco ASR1000-RP1.
An external alarm monitoring facility uses this signal to activate a visible alarm (such as a flashing
light) or an audible alarm that immediately alerts site personnel to the existence of a router alarm
condition.
An external audible alarm can be reset by clearing the condition that caused the alarm or by pressing the
Audible Cutoff (ACO) button on the Cisco ASR1000-RP1. An audible alarm can be sounded to
immediately alert you of an alarm condition in the router. An audible alarm generated by the system
continues to sound until you either clear the alarm condition itself or press the ACO button to silence the
alarm. Pressing this button does not resolve the alarm condition.
Table 2-2 lists the Cisco ASR 1000 Series Route Processors connectors and description.
Table 2-2 Cisco ASR 1000 Series Route Processor Connectors
Label Type Description

ACO Audible Cutoff button When you press this button, an interrupt is
generated informing software that the audible alarm
relays will be disabled. This interrupt generates to
both processors.
0 USB0 interface Side-by-side USB connector used with memory
sticks or smart cards for secure key distribution
1 USB1 interface Side-by-side USB connector used with memory
sticks or smart cards for secure key distribution
BITS RJ-45 connector Indicates BITS timing reference.
MGMT One RJ-45 jack for The route processor has an ENET port with a RJ-45
ETHERNET copper Ethernet connector to attach a management device or
Management Port network for network management.
OL-13208-03 2-5

Table 2-2 Cisco ASR 1000 Series Route Processor Connectors (continued)

CON One RJ-45 for CON/AUX Console port used to connect to a terminal.
AUX One RJ-45 for CON/AUX Auxiliary port used for remote management
purposes.
The Cisco ASR 1000 Series Route Processor meets the following requirements:
• Supports up to 4GB(bytes) of memory with single-bit error correction and multi-bit error detection
except for the built-in RP1 on the Cisco ASR1002 router
• Supports On-board Failure Logging (OBFL) with 2MB of memory
• Supports the Cisco ASR 1000 Series Router system architecture and midplane
• Enhanced Serdes Interconnect (ESI) at 11.5Gbps.
• Gigibit Ethernet switches for EOBC communication and boot-up of the Cisco ASR 1000 Series SPA
Interface (SIP) and Cisco ASR 1000 Series Embedded Services Processor.
• Runs Cisco IOS network control plane (routing protocol, connections setup)
• Cisco IOS punt packet forwarding
• Active/Standby Cisco ASR 1000 Series Route Processor 1 and Cisco ASR 1000 Series Embedded
Services Processor selection
• Code storage and download operational code to Cisco ASR 1000 Series Embedded Services
Processor and Cisco ASR 1000 Series SPA Interface (SIP)
• Bulk storage: by default, it comes with a 40GB hard disk drive (HDD). A 32GB solid state disk drive
(SSD optional) can also be configured.
• 2 MB upgradeable BootROM, 1GB embedded USB memory (eUSB), except for the built-in RP1 on
the Cisco ASR1002 router.
• Comes with 2GB of DRAM as default and can be upgradeable to 4 GB DRAM.
• Front panel support: Console, 10/100 Management port, two USB ports, CON port, and AUX port.
The two serial ports can run up to 115.2kbps with hardware flow control. One port is used as the
CONSOLE port for secure configuration and status display. The default BAUD rate for the CONSOLE
port should be set at 9600 BAUD. The console port is an asynchronous serial port; any devices connected
to this port must be capable of asynchronous transmission.
The auxiliary port connects a modem or other DCE device (such as a CSU/DSU or other router) to allow
remote service and dial backup access to the system. Both the console and auxiliary ports are
asynchronous serial ports; any devices connected to these ports must be capable of asynchronous
transmission.The AUX port is a diagnostics access port.
Cisco Embedded ASR1000-RP1 for Cisco ASR 1002 Router

The route processor for the Cisco ASR 1002 Router is integrated in the chassis and supports all the
typical customer management interfaces such as the Ethernet network management port and console and
auxiliary serial ports of the route processor for the Cisco ASR 1006 and ASR 1004 routers. It also has
LED status indicators, an RJ-45 plug for a BITS timing reference and one USB ports which can be used
with smart cards for secure key distribution or for image or configuration file updates. Figure 2-3 shows
the Cisco ASR1000-RP1 LEDs for the Cisco ASR1002 router.
2-6 OL-13208-03

Figure 2-3 Embedded Cisco ASR1000-RP1 LEDs
ASR 1002
pwr min
stat maj
crit
250603
The embedded route processors for the Cisco ASR 1002 Router provides connection for one SPA bay
and the circuitry for the a built-in 4xGE SPA.
The Cisco route processor for ASR 1002 Router meets the requirements of route processors for the
Cisco ASR 1006 and the Cisco ASR 1004 routers; except for the following deviations:
• No SATA hard drive supported. Bulk file storage is on a large fixed eUSB device (up to 8GB (bytes)
supported).
• No support for redundant route processors.
• Hardware memory and storage options (such as DRAM) are not field upgradeable.
• Network clock changes. No second BITS clock input supported.
• The LED order is from top to bottom on the route processor is MIN, MAJ, CRIT.
Table 2-3 lists the Cisco embedded ASR1000-RP1 LEDs and behaviors.
Table 2-3 Cisco Embedded ASR1000-RP1 LEDs in the Cisco ASR 1002 Router

PWR Power Solid green All power requirements are within
specification
STAT System status Solid green Cisco IOS has successfully booted.
Yellow ROMMON is running or when the Process
Manager declares that a critical ASR 1000
Series RP1 process is not running
Red System failure or powering up.
MIN Minor Amber Minor alarm indicator.
MAJ Major Red Major alarm indicator.
CRIT Critical Red Critical alarm indicator.
BOOT eUSB0 FLASH Flashing Green Activity indicator.
(BootDisk Off No activity.
CARRIER Off Out of service or not configured.
Green In frame and working properly.
Amber Fault or loop condition.
OL-13208-03 2-7

Table 2-3 Cisco Embedded ASR1000-RP1 LEDs (continued) in the Cisco ASR 1002 Router

LINK 10/100 /1000 RJ-45 Green Link with no activity.
Interface LED Flashing Green Link with activity.
Off No link.
4 LEDs Built-in SPA SFP Off Port is not enabled.
port status Amber Port enabled but there is a problem with the
Ethernet link.
Green Port enabled, valid Ethernet link
PWR Carrier card power Green All carrier card requirements are within
specification.
STAT Carrier card status Green Only when the SPA drivers have started and
are running and all critical processes are
running
Yellow When ROMMON is running and during the
download and boot of the operating system
Red A fault is detected or the card is powering
up.
Table 2-4 lists the Cisco embedded ASR1000-RP1in the Cisco ASR 1002 Router connectors and
description.
Table 2-4 Cisco Embedded ASR1000-RP1 Connectors

BITS Standard E1/T1 RJ-45 Indicates BITS timing references.
connector
MGMT One RJ-45 jack for The route processor has an ENET port with a RJ-45
copper Ethernet connector to attach a management device or network
Management Ethernet for network management.
Port
CON One RJ-45 for CON Console port used to connect to a terminal.
AUX One RJ-45 for AUX Auxiliary port used for remote management
purposes.
2-8 OL-13208-03

Cisco ASR 1000 Series Embedded Services Processors
Figure 2-4 shows a fully-loaded Cisco ASR 1002 Router.
Figure 2-4 Cisco ASR 1002 Router Route Front View
1
2
TUS
C/A
STA
C/A
A/L
C/A
A/L
3-POS
SPA-4XOC
C/A
A/L
PWR STAT
3
A/L
CON
TUS
AUX
C/A
MGMT
STA
1
C/A
LINK
A/L
MTS
C/A
A/L
CARRIER 3-POS
BOOT SPA-4XOC
C/A
QE3
A/L
QE2
3
QE1
A/L
QE0
2
STAT
1
ASR 1002
0
TUS
C/A
min
STA
stat
C/A
A/L
maj
C/A
A/L
pwr SPA-4XOC
3-POS
C/A
crit
A/L
3
A/L
2
4
1
0
280283
3
1 FO slot 3 The eUSB panel door on the side of the Cisco

ASR 1002 Router must not be opened. If there
is a problem with eUSB flash card, the chassis
should be returned.
2 R0 slot 4 Grounding stud

The Cisco ASR 1000 Series Embedded Services Processor (ESP) is based on the Cisco QuantumFlow
Processor for next-generation forwarding and queuing.
The Cisco ASR 1000 Series ESPs:
• Provide the centralized embedded forwarding services responsible for the bulk of the data plane
processing tasks. All network traffic through the Cisco ASR1000 Series system flows through the
Cisco ASR 1000 Series Embedded Services Processors.
• Are responsible for the data-plane processing tasks and all network traffic flows through them.
• Support Forwarding Engine Control Processor which provide hardware abstraction layer between
the QFP-based forwarding engine and other system components, allowing datapath and management
functions to be independent.
• Support Cisco QuantumFlow Processor (QFP) forwarding engines.
• Support QFP provisioned with two TCAM4 devices for ACL lookup and other software features.
• Perform all baseline packet routing operations, including MAC classification, Layer 2 and Layer 3
forwarding, quality-of-service (QoS) classification, policing and shaping, security access control
lists (ACLs), VPNs, load balancing, and NetFlow.
• Are responsible for features such as firewalls, intrusion prevention, Network Based Application
Recognition (NBAR), Network Address Translation (NAT), and flexible pattern matching.
• Incorporates a security encryption coprocessor to assist encryption processing common to all ESPs.
The security processor operates in coprocessor mode and only processes packets sent to it by the
Cisco QFP.
• Provide hardware abstraction layer between the packet processing-based forwarding engine and
other system components.
OL-13208-03 2-9

The Cisco ASR 1000 Series routers support the following Cisco ASR 1000 Series Embedded Services
Processors:
• Cisco ASR1000-ESP5
Note The Cisco ASR1000-ESP5 does not support redundant configurations.
• Cisco ASR1000-ESP10-N—The Cisco ASR1000 Embedded Services Processor 10G Non Crypto
Capable board provides an ASR1000 solution for customers who are under export restrictions and
not qualified to implement products that support strong encryption services. The Cisco ASR1000
Embedded Services Processor 10G Non Crypto Capable feature support is the same as the Cisco
ASR100-ESP10 except that SSH, SSL and IPSec VPN services are not supported. For detailed
information about this feature, refer to the Cisco ASR 1000 Series Aggregation Services Routers
Software Configuration Guide and the Cisco ASR 1000 Embedded Services Processor 10G Non
Crypto Capable Feature Guide.
Note Upgrading from a Cisco ESP to another Cisco ESP can be performed on redundant ESP systems only
(Cisco ASR1006 and Cisco ASR1004 routers). The Cisco ASR1002 router supports only one Cisco
ASR1000-ESP5 or ASR1000-ESP10. The Cisco ASR1006 and Cisco ASR1004 routers do not support
the Cisco ASR1000-ESP5. Therefore, when performing upgrades, the Cisco ASR1000-ESP10,
Cisco ASR1000-ESP20, and any future ESPs can be upgraded.
Note Do not have different embedded services processors operating in the same chassis. The only time this
condition occurs is when you are performing an upgrade.
IThe Cisco ASR 1000 Series Embedded Services Processors consist of three main elements:
• Cisco QuantumFlow Processor for packet processing and queueing and scheduling
• Data plane interconnect
• Forwarding Engine Control Processor (FECP) (located on the Cisco ASR Series Embedded Services
Processor)
All initial Cisco ASR 1000 Series Embedded Services Processors are based on a common
highly-programmable network Cisco QuantumFlow Processor (packet processing).
2-10 OL-13208-03

Table 2-5 Differences in Cisco ASR1000 Embedded Services Processors
Feature Cisco ASR1000-ESP5 Cisco ASR1000-ESP10 Cisco ASR1000-ESP20

Memory 256MB Cisco QuantumFlow 512MB Cisco QuantumFlow 1GB Cisco QuantumFlow Processor,
Processor, 10Mb TCAM, Processor, 10Mb TCAM, and 40Mb TCAM, 256MB packet buffer,
64MB packet buffer, and 128MB packet buffer, and 2GB 4GB FECP DRAM
1GB FECP DRAM FECP DRAM
Performance 4 Mpps for the combination 8 Mpps forwarding for the 16 Mpps forwarding for the
of the following combination of the following combination of the following
commonly-used features: commonly-used features: IPv4 commonly-used features: IPv4
IPv4 forwarding, IP forwarding, IP Multicast, ACL, forwarding, IP Multicast, ACL, QoS,
Multicast, ACL, QoS, QoS, Reverse Path Forwarding Reverse Path Forwarding (RPF), load
Reverse Path Forwarding (RPF), load balancing, and balancing, and Sampled NetFlow
(RPF), load balancing, and Sampled NetFlow
Sampled NetFlow
Bandwidth 5Gbps of bandwidth 10Gbps of bandwidth 20Gbps of bandwidth
Security Traffic 1Gbps 3 Gbps 8Gbps
Performance
Product Located in slot 1 and is Located in: Located in:
Compatibility labeled F0 in the Cisco ASR
• Cisco ASR 1006 Router • Cisco ASR 1006 Router physical
1002 Router only
physical slots 3 and 4 and are slots 3 and 4 and are labeled F0
labeled F0 and F1. and F1.
• Cisco ASR 1004 Router • Cisco ASR 1004 Router physical
physical slot 1 and is labeled slot 1 and is labeled F0.
F0.
• Cisco ASR 1002 Router
Note The Cisco ASR 1002 Router
physical slot 1 (top slot) and
does not support the
is labeled F0.
Cisco ASR1000-ESP20.
The Cisco ASR 1000 Series Embedded Services Processor (ESP) consists of a front panel label for
indicator and control functions. The Cisco ASR 1000 Series Embedded Services Processor model
number labeling is located next to the left card module handle. The module also contains card handles
to assist in insertion or removal of the module.
Figure 2-5 shows the Cisco ASR 1000 Series Embedded Services Processor LEDS on the front panel.
Note The Cisco ASR 1000 Series embedded services processors have the same faceplate and status
information except for the name label, such as Cisco ASR1000-ESP20, Cisco ASR1000-ESP10, Cisco
ASR1000-ESP10-N, or Cisco ASR1000-ESP5.
OL-13208-03 2-11

Figure 2-5 Cisco ASR1000-ESP10 Faceplate LEDs
1 2
PWR ACTV
STAT STBY
ASR1000-ESP10
280080
3 4
1 PWR—Power LED 3 STAT—Status LED

2 ACTV—Active LED 4 STBY—Standby LED
Table 2-6 lists the Cisco ASR1000-ESP5, ASR1000-ESP10, and ASR1000-ESP20 LEDs and behaviors.
Table 2-6 Cisco ASR1000 ESP LEDs for the Cisco ASR 1000 Series Routers
LED Label LED Color Behavior Description

PWR Power Solid green All power requirements are within specification
Off The ESP is not powered on.
STAT System status Solid green Cisco IOS has successfully booted.
Yellow ROMMON is running or when the Process Manager declares
that a critical ASR 1000 Series RP1 process is not running
Red System failure or powering up.
ACTV Active Green The ACTV LED indicates (in a redundant system) which ESP
board is actively forwarding packets
The active ESP board will have a green ACTV LED and the
STBY LED will be off. The standby ESP board will have a
yellow STBY LED and the ACTV LED will be off.
Note that in a ASR1002 or ASR1004 chassis, any ESP board
will always be active since these chassis does not support
redundancy. The ASR1000-ESP5 does not support redundancy,
therefore it will always be active.
STBY Standby Yellow The STBY LED indicates (in a redundant system) which ESP
board is in a standby mode waiting to take over packet
forwarding in case the active ESP board experiences a failure.
Will always be off if active Cisco ASR1000-ESP is on.
2-12 OL-13208-03

Cisco ASR 1000 Series SPA Interface Processor
Cisco ASR 1000 Series SPA Interface Processor

This section describes the SPA interface processor for the Cisco ASR 1006 and Cisco ASR 1004 routers
and the Cisco embedded ASR1000-SIP10 for the Cisco ASR 1002 Router.
The Cisco ASR 1000 Series SPA Interface Processor for the Cisco ASR 1006 and Cisco ASR 1004
routers:
• Is a carrier card that inserts into a router slot like a line card.
• Contains one or more subslots which house one or more shared port adapters.
• Supports online insertion and removal (OIR) with SPAs inserted in the subslots. SPAs also support
OIR and can be inserted or removed independently from the SIP.
This section describes the Cisco ASR 1000 Series SPA Interface (SIP) components and subslot
identification.
Figure 2-6 shows the Cisco ASR 1000 Series SPA Interface (SIP) module.
Figure 2-6 Cisco ASR 1000 Series SPA Interface Processor Faceplate
1 2
ASR1000-SIP10
0
1
ASR1000-SIP10G
231510
PWR STATUS
2
3
3 4 5 6
1 SPA subslot 0 4 STATUS Led

2 SPA subslot 1 5 PWR Led
3 SPA subslot 2 6 SPA subslot 3
Figure 2-7 shows the LEDs on the Cisco ASR1000-SIP 10.
Figure 2-7 Cisco ASR1000-SIP10 SPA Interface Processor
ASR1000-SIP10
280081
PWR STATUS
2 1
1 STATUS LED 2 PWR LED
OL-13208-03 2-13

Shared Port Adapters
Table 2-7 describes the Cisco ASR 1000 Series SIP10 LEDs on the front panel.
Table 2-7 Cisco ASR1000-SIP10 LEDs
LED Label LED Color—State Behavior Description

PWR Power Solid green Cisco ASR 1000 Series SIP is powered on
Off Cisco ASR 1000 Series SIP is powered off
STATUS System status Solid green The Cisco ASR 1000 Series SPA Interface
Processor has encountered an error
Yellow Lit when the Cisco ASR 1000 Series SIP is
loading
Red The SPA drivers have started and are
running and all critical processes are
running (as determined by the Cisco ASR
1000 Series SPA Interface (SIP) Process
Manager).
The Cisco ASR1002-SIP10 supports a built-in 4xGE SPA and three half-height SPAs (one half-height
and one full height SPA). The Cisco ASR1002-SIP10 also functions as the base board for the Cisco
embedded ASR1000-RP1. The Cisco 1002 Router has one slot for FP0 with three subslots for SPAs,
subslots 1 - 3.

A shared port adapter is a modular type of port adapter that inserts into a subslot of a compatible SIP to
provide network connectivity and increased interface port density. The Cisco ASR 1000 Series SPA
Interface Processor (SIP) provides an aggregation function for SPAs.
In the Cisco ASR 1006 Router, the Cisco ASR1000 Series SIP supports:
• 4 half-height (HH) (¼ rate or full rate or combination)
• 2 full-height (FH) (¼ rate or full rate or combination) SPAs with up to 32 ports per SPA
• 2 half-height and 1 full-height combination that does not exceed 64 ports
Figure 2-8 shows the slot numbering for the shared port adapters on the Cisco ASR 1000 Series SPA
Interface for the Cisco ASR 1006 Router and Cisco ASR 1004 Router.
Figure 2-8 Cisco ASR1000 Series SPA Interface Subslot Numbering
Front of SIP, horizontal chassis slots
SPA 0 SPA 1
231508
SPA 2 SPA 3
In the Cisco ASR 1004 Router, the Cisco ASR1000 Series SIP supports:
• Four half height (¼ rate or full rate or combination)
2-14 OL-13208-03

• Two full height (¼ rate or full rate or combination) SPAs with up to 32 ports per SPA
The slot numbering for the SPAs in the Cisco ASR 1004 Router is the same as in the Cisco ASR 1006
Router.
In the Cisco ASR 1002 Router, the Cisco ASR1002-SIP10 supports:
• Three removable half height SPAs on Bay 1, 2, and 3
• The fourth SPA which is a built-in 4xGE SPA on Bay 0 located on the Cisco ASR 1000 Series RP1
Note The shared port adapters on the Cisco ASR1002-SIP10 support online insertion and removal.
However, the Cisco ASR1002-SIP10 in the Cisco ASR 1002 Router is built into the chassis and
is not a field-replaceable unit and does not support online insertion and removal.
Figure 2-9 shows the slot numbering for the shared port adapters on the Cisco ASR 1000 Series SPA
Interface for the Cisco ASR 1002 Router.
Figure 2-9 Cisco ASR1002-SIP10 Interface Subslot Numbering
1 3
PWR ACTV
STAT STBY
ASR1000-ESP10
C/A
C/A
C/A
C/A
pwr min
US
AT
A/L
A/L
A/L
A/L
ST
stat maj
SPA-4XOC3-POS
crit
280369
C/A
C/A
C/A
C/A
C/A
C/A
C/A
C/A
US
US
AT
AT
A/L
A/L
A/L
A/L
A/L
A/L
A/L
A/L
ST
ST
0
3
2 4
1 Cisco embedded ASR1000-RP1 subslot 0 3 SPA subslot 1

The Cisco embedded ASR1000-SIP10 (in the Cisco ASR 1002 Router) supports one built-in 4xGE SPA
and three half height SPAs in any one of the following configurations:
• Built-in 4xGE SPA in bay 0 and three half height SPAs in bay 1, 2, 3.
• Built-in 4xGE SPA in bay 0, one half height SPA in bay 2, and one full height SPA in bay 1.
The Cisco ASR 1000 Series SPA interface processor houses SPA bay 2 and SPA bay 3. SPA bay 0 and
SPA bay 1 are physically located on Cisco embedded ASR1000-RP1. A portion of the Cisco embedded
ASR1000-RP1 is reserved to provide connectivity between SPA bay 1 and the Cisco embedded
ASR1000-SIP10.
Note The embedded Cisco ASR1000-RP1 subslot 1 must communicate to subslot 3 of the embedded SIP when
running a full height SPA in subslot 1.
For information about specifying SIP subslot location for a SPA and specifying slot location for a SIP,
see theCisco Aggregation Services Router 1000 Series SIP and SPA Installation Guide.
OL-13208-03 2-15

Cisco ASR 1000 Series Router Power Supplies

All Cisco ASR 1000 Series Router configurations support AC and DC power supply options. The
modular chassis configurations support the installation of two power supplies for redundancy. When an
external power supply fails or is removed, the other power supply provides power requirements for the
chassis.
You are required to always have two power supplies installed in the chassis to insure sufficient cooling
for the box. The system fans are inside the power supply unit and must spin for cooling. No Cisco
ASR 1000 Series Router will operate for more than five minutes without two power supplies installed.
Since all the system fans can be powered by one power supply, it is not required for the second power
supply unit to be powered on, but it must be installed. Cisco IOS software specifically looks for two
power supplies in the chassis and will automatically initiate a shutdown if only one power supply is
detected.
• Power Supply Requirements for All Cisco ASR 1000 Series Routers, page 2-16
• Power Supplies for Cisco ASR 1006 Router, page 2-18
Power Supply Requirements for All Cisco ASR 1000 Series Routers
This section contains power supply specifications for the Cisco ASR 1006, ASR 1004, and ASR 1002
routers. The following topics are covered:
• DC power supply input ratings and circuit breaker specifications
– Maximum and minimum Amps for the branch circuit breakers
– Maximum and minimum size of the AWG wire required for each circuit breaker.
• AC and DC power supply types
• AC and DC power supply ratings
2-16 OL-13208-03

DC Power System Input Requirements for Cisco ASR 1000 Series Routers
The DC power supply for the Cisco ASR 1006, ASR 1004, and ASR 1002 routers operate at
specifications. shows the common input ranges and circuit breaker requirements.
Table 2-8 Cisco ASR 1000 Series Router DC Power Supply System Input Requirements
Cisco ASR 1000

Series Router DC
Power Supply System Input Rating (Amps) Circuit Breaker Amps AWG # Wire
Minimum Maximum Minimum Maximum
Cisco ASR 1006 40 Always 50 Always AWG #6 wire
Cisco ASR 1004 24 30 40 10 8
Cisco ASR 1002 16 20 30 12 10
For example, the Cisco ASR 1002 Router DC power supply, with 16 Amp input rating must use an AWG #12 gauge wire for a 20Amp circuit breaker and
an AWG #10 gauge wire for a 30Amp circuit breaker.
Note All Cisco ASR 1000 Series Router AC power supplies require a 20 AMP circuit breaker.
AC and DC Power Supply Types

The AC and DC power supplies for the Cisco ASR 1000 Series Routers support different types of power
supply switches. Table 2-9 defines which power supplies the Cisco ASR 1000 Series routers support (a
Standby or an On/Off switch).
Table 2-9 Cisco ASR 1000 Series Routers AC and DC Power Supply Switches
Switch Type
Supported
Symbol Cisco ASR 1000 Series Router Power Supply
On/Off circuit I/O ASR 1006 DC
ASR 1004 DC
ASR 1002 AC
Standby switch A broken ASR 1006 AC
circle with
ASR 1004 AC
a vertical
line ASR 1002 DC
through the
top of it
AC and DC System Power Ratings

Table 2-10 lists AC and DC power supply system rating requirements for all Cisco ASR 1000 Series
Routers.
OL-13208-03 2-17

Table 2-10 AC and DC Power Supply System Rating Specifications for the Cisco ASR 1000 Series Routers
Description Specification
Power supply declared ratings AC = 100-240 VAC
DC = –48/ –60 VDC
Nominal line frequency rating 50/60 Hz
Power Supplies for Cisco ASR 1006 Router

The Cisco ASR 1006 Router can support up to 1200W output (AC and DC input). The 1200W power
supply module consists of either an AC or DC input and 1200 watt output closed frame power supply
with two DC voltage outputs: 12V and 3.3V.
Each power supply module contains three internal fan modules and provides the forced air cooling for
the chassis. These power supply modules contain a monitor circuit to determine the status of fan speed
and operation along with LED status indicating fan errors.
The system temperature operation is 0 to 40C normal and –5C to +55C.
• AC System—AC power input is an IEC 320-type power inlet, 20A service connector. The AC input
side contains a front panel with provisions for mounting screw, built in handle to extract the power
supply, three status LEDs, and fans for power supply and system cooling.
• DC System—Two-position terminal block-style connector, with labeled connections for - (–48/60 V
input) and + (–48/60 V Return). The DC input side contains a front panel with provisions for
mounting screw, built in handle to extract the power supply, three status LEDs, and fans for power
supply and system cooling.
See Appendix A, “Cisco ASR 1000 Series Routers Specifications.” for detailed power supply
specifications.
Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that
the protective device is rated not greater than: AC power supplies for the Cisco Aggregation Services
Routers: 120 VAC, 20A U.S. maximum. DC power supplies for the Cisco ASR 1006 Router: 50A U.S.
maximum; Cisco ASR 1004 Router: 40A U.S. maximum: Cisco ASR 1002 Router: 30A U.S. maximum.
Statement 1005
AC Power Supply LEDs and Connector for Cisco ASR 1006

This section provides information about the AC power supplies on the rear of the Cisco ASR 1006
Router. The power supply module contains three fans mounted in the power supply module. A total of
six fans are used to cool the ASR 1006 system and power supply. The airflow direction is front to back.
Power supply modules with internal fan modules install into the rear of the chassis. These modules
contain integral handles to ease installation and removal (no insertion or extraction levers are provided).
A single blind mate connector located on the inlet side of these modules mates with a connector mounted
on back side of the midplane.
Guide pins located at the rear of these modules help center locate the modules and reduce stress to the
midplane and module mounted connectors. Four captive screws (tool operated latches) are provided on
the modules face plate (chassis rear) to secure these modules into the chassis.
2-18 OL-13208-03

Figure 2-10 shows the AC power supplies at the rear of the Cisco ASR 1006 Router.The Cisco ASR 1006
Router supports up to two power supplies. The power supply LEDs and connectors on the rear of the
chassis are described in Table 2-11.
Figure 2-10 Cisco ASR 1006 Router AC Power Supply
6 7 8
OUTPUT INPUT INPUT

FAIL OK OK
ALARMS
60V
1A MAX
100-240V~ 16-7A
50-60HZ
5 This unit might have more than
one power supply connection.
All connections must be removed
to de-energize the unit.
280029
4
3 2 1
1 AC power supply fan 5 AC power supply handle

2 DB-25 alarm connector 6 AC power inlet
3 Tie-wrap tab 7 AC power supply Standby switch
4 AC power supply captive screw 8 AC power supply LEDs
Figure 2-11 shows the AC power supplies LEDs and DB-25 Alarm connector.
OL-13208-03 2-19

Figure 2-11 Cisco ASR 1006 Router AC Power Supply LEDs and DB-25 Alarm Connector
280028
OUTPUT
INPUT FA
N
FAIL
OK OK
ALARMS
60V
1A MAX.
4 2
1 AC power supply LEDs 3 DB-25 alarm connector

2 AC power supply fan 4 AC power supply fan
Table 2-11 describes the AC power supply LEDs on the Cisco ASR 1006 Router.
Table 2-11 Cisco ASR 1006 Router AC Power Supply LEDs
LED Label LED Color Description

INPUT OK Power supply activity Green LED illuminates green to signal that the AC power supply
input voltage is greater than 85V.
None If LED is not illuminated, then the AC input voltage is
less than 70V or the power supply is turned off. For an AC
input voltage between 70V and 85V, the INPUT OK LED
can be either on, off, or flashing
2-20 OL-13208-03


FAN OK Bi-color LED indicates Green LED illuminates green when all fans are operational.
fan status Red The LED illuminates red when a fan failure is detected.
OUTPUT FAIL Power supply activity Red LED is red and turned off to signal that the DC output
voltages are within the normal operating range; output
voltage between the minimum and maximum limits will
not create an output fail alarm, and output voltages below
the minimum or above the maximum will create an output
fail alarm.
When you turn the power supply on, the red LED is
illuminated for two to three seconds for testing LED
operation before going off.
DC Power Supply LEDs and Connectors for Cisco ASR 1006

This section provides information about the DC power supplies on the rear of the Cisco ASR 1006
Router. The maximum branch circuit for the DC power supply module is 60A and the minimum is 50A.
The DC power supply operates within specification from –48 VDC to –60 VDC continuously. The Cisco
ASR 1006 Router has two of the same type power supplies in power supply slot 0 and power supply
slot 1. The power supply slot numbers are on the left side of the chassis and the power supplies are
located on the floor of the chassis.
The DC input connector is a terminal block style that supports a AWG #6 wire. The terminal block is
compliant to all safety agencies and electrical requirements of the supply. Use the tie wraps to dress the
input cable wires. There are three tie wrap tabs on the power supply.
The terminal block accepts two double-hole lugs, one for –48V input and another for –48V RTN. A
plastic cover fits over the terminal block to prevent accidental contact. See Figure 5-19.
Note The studs on the terminal block are similar to the safety ground device on the side of the Cisco ASR 1006
Router. For information on the safety ground lug on the side of the chassis.
The unit requires a power switch circuit breaker to serve as the main disconnect for the DC input to the
power supply. The circuit breaker meets international safety requirements and supports 80 VDC and has
a current rating of 50 A. The power supply unit is secured into the system chassis with four captive
screws mounted on the faceplate.
Figure 2-12 shows the DC power supplies at the rear of the Cisco ASR 1006 Router. The Cisco ASR
1006 Router supports up to two power supplies. The power supply LEDs and connectors on the rear of
the chassis are described in the Table 2-12.
OL-13208-03 2-21

Figure 2-12 Cisco ASR 1006 Router DC Power Supply
9 10
OUTPUT INPUT INPUT

FAIL OK OK
OFF
55
ALARMS
60V
-48/-60V 40A
1A MAX
280023
7 This unit might have more than one power supply connection. All connections must be removed to de-energize the unit.
6 5 4 3 2 1
1 Fans 6 DC Power supply earth ground lugs

2 DB-25 alarm connector 7 DC Power supply captive screws
3 Tie-wrap tabs 8 DC Power supply handle
4 DC power supply terminal and plastic cover 9 DC power supply On (|) /Off (O) switch
5 Earth grounding symbol 10 DC power supply LEDs
Table 2-12 describes the LEDs on the Cisco ASR 1006 Router DC power supply.
Table 2-12 Cisco ASR 1006 Router DC Power Supply LEDs

INPUT OK A bi-color LED Green LED illuminates green to signal that the DC power supply input
indicates voltage is greater than–43.5VDC at turn-on and remains green down
presence of to –39VDC.
input voltage Amber The LED illuminates amber when the input voltage (falls below
–39VDC) and indicates that there is still a voltage present (voltage on
the terminal block). The LED remains amber and is active to around
20V +/-5V. The LED is not illuminated if the input is below –15V.
FAN OK A bi-color LED Green The LED illuminates s green when all fans are operational.
indicates power Red The LED illuminates red when a fan failure is detected.
supply fan status
OUTPUT FAIL Power supply Red When the LED is off, it signals that the DC output voltage are within
activity the normal operating range. Output voltage between the minimum and
maximum limits will not create an output fail alarm, and output
voltages below the minimum or above the maximum will create an
Output Fail alarm.
When you turn the power supply on, the red LED illuminates for two
to three seconds to test LED operation before going off.
2-22 OL-13208-03

AC/DC Power System Output for Cisco ASR 1006
The power supply output tolerance is defined in Table 2-13 under all combinations of line variation.
Total system consumption per power supply should not exceed 1200 W.
Table 2-13 Cisco ASR 1006 Router Power System Output Voltage and Current
Output Voltage +12 VDC +3.3 V

Minimum 11.80 VDC 3.20 VDC
Nominal 12.00 VDC 3.30 VDC
Maximum 12.20 VDC 3.40 VDC
Output Current
Minimum 2.80 A 0.10 A
Maximum 101.7 A 3.125 A

The Cisco ASR 1004 Router can support up to 735 W output (AC and DC input). The 735W power
supply module consists of either an AC or DC input with two DC voltage outputs: 12V and 3.3V.
Each power supply module contains three internal fan modules and provides the forced air cooling for
the chassis. These power supply modules contain a monitor circuit to determine the status of fan speed
and operation along with LED status indicating fan errors.
The system temperature operation is 0 to 40C and –5C to +55C.
• AC System—AC power input is an IEC 320-type power inlet, 15A service connector. The AC input
side contains a front panel with provisions for mounting screw, built in handle to remove the power
• DC System—Three-position terminal block-style connector, with labeled connections for -
(–48/60 V input) and + (–48/60 V Return) and GND (earth ground symbol). The DC input side
contains a front panel with provisions for mounting screw, built in handle to extract the power
See Appendix A, “Cisco ASR 1000 Series Routers Specifications.” for detailed power supply
specifications.
Statement 1005
Cisco ASR 1004 AC Power Supply

Router. The power supply module contains three fans mounted in the power supply module. A total of
six fans are used to cool the ASR 1004 system and power supply. The airflow direction is front to back.
OL-13208-03 2-23

Power supply modules with internal fan modules install into the rear of the chassis. These modules
contain handles to ease installation and removal. The AC power supply has a front panel mounted switch
that powers on and off the power supply. This switch will not disconnect the AC line, but will act only
as a standby switch to the power supply. The front panel includes a mechanical guard to prevent the
standby switch from being tripped due to accidental contact.
midplane and module mounted connectors. Four captive screws (tool operated latches) are provided on
Cisco ASR 1004 AC Power Supply LEDs and Connector

Figure 2-13 shows the AC power supplies at the rear of the Cisco ASR 1004 Router.The Cisco ASR 1004
Router supports up to two power supplies. The power supply LEDs and connectors on the rear of the
chassis are described in Table 2-14.
1 2
OUTPUT INPUT FAN

FAIL OK OK
100V-240V~ 12A-5A
ALARMS
50-60Hz
60V
1A MAX
OUTPUT INPUT FAN

FAIL OK OK
100V-240V~ 12A-5A
ALARMS
50-60Hz
60V
1A MAX
280184
6 5 4 3
1 AC power supply Standby switch (standby 4 AC power supply fan

symbol is a broken circle with a vertical line
through the top of it)
2 AC power supply LEDs 5 AC power inlet
3 DB-25 alarm connector 6 AC power supply handle
2-24 OL-13208-03

Figure 2-14 shows the AC power supplies LEDs and DB connector.
Figure 2-14 Cisco ASR 1004 Router AC Power Supply LEDs and DB -25 Alarm Connector
280028
OUTPUT
INPUT FA
N
FAIL
OK OK
ALARMS
60V
1A MAX.
4 2
1 AC power supply LEDs 3 DB-25 alarm connector

2 Power supply fan 4 AC power supply fan
Table 2-14 Cisco ASR 1004 Router AC Power Supply LEDs and Connector

INPUT OK Power supply activity Green LED illuminates green to signal that the AC power supply
None If LED is not illuminated, then the AC input voltage is
less than 70V or the power supply is turned off. For an AC
OL-13208-03 2-25


fail alarm.
When you turn the power supply on, the red LED is
illuminated for two to three seconds for testing LED
operation before going off.
Cisco ASR Router 1004 DC Power Supply

Router. For the maximum branch circuit for the DC power supply module, see Table 2-8.
The DC power supply operates within specification from –48 VDC to –60 VDC continuously. The Cisco
ASR 1004 Router has two of the same type power supplies in power supply slot 0 and power supply
slot 1. The power supply slot numbers are on the left side of the chassis and the power supplies are
located on the floor of the chassis.
The DC power supply input connector is a terminal block style that will allow crimp type lugs accepting
up to AWG #8 wire. The terminal block is compliant to all safety agencies and electrical requirements
of the supply. The terminal block accepts two-hole lugs (#10 stud) for all connections with center to
center spacing of 0.625 inches. A plastic cover goes over the terminal block to prevent accidental
contact. The connection order shall be negative (–), positive (+), and GND terminals.
The unit requires a power switch circuit breaker to serve as the main disconnect for the DC input to the
power supply (Table 2-8 see for current rating requirements.) The power supply unit is secured into the
system chassis with four captive screws mounted on the faceplate.
Cisco ASR 1004 Router DC Power Supply LEDs and Connector
Figure 2-15 shows the DC power supplies at the rear of the Cisco ASR 1004 Router. The Cisco
ASR 1004 Router supports up to two power supplies. The power supply LEDs and connectors on the rear
of the chassis are described in the Table 2-15.
2-26 OL-13208-03

1 2
OUTPUT INPUT FAN

FAIL OK OK
60V
1A MAX
OUTPUT INPUT FAN

FAIL OK OK
60V
1A MAX
280185
7 6 5 4 3
1 DC power supply terminal and plastic cover 5 Earth grounding symbol

2 DC power supply LEDs 6 DC power supply On (|) /Off (O) switch
3 DB-25 alarm connector 7 DC power supply handle
Power supply ground lugs (+ and –)
4 DC power supply fan

OL-13208-03 2-27


supply fan status
Output Fail alarm.
DC Power System Input for Cisco ASR 1004
The DC power supply operates within specification from –40.5VDC to –72VDC continuously once the
the power supply DC input turn on threshold of –43.5V has been reached. Table 2-21 shows the common
input ranges for reference only.
Table 2-16 Cisco ASR 1004 Router DC Power System Input
Voltage Range (VDC) Minimum Nominal Maximum

Domestic –40.5 –48 –56
International –55 –60 –72
AC/DC Power System Output for Cisco ASR 1004
The power supply output tolerance is defined in Table 2-17 under all combinations of line variation.
Total system consumption per power supply should not exceed 735 W.
Table 2-17 Cisco ASR 1004 Router Power System Output Voltage and Current

Minimum 11.80 VDC 3.20 VDC
Nominal 12.00 VDC 3.30 VDC
Maximum 12.20 VDC 3.40 VDC
Output Current
Minimum 2.80 A 0.10 A
Maximum 61.44A 3.125 A

The Cisco ASR 1002 Router supports an AC or DC power supply:
• Cisco ASR 1002 Router AC Power Supply, page 2-29—The AC power supply operates between
85VAC and 264VAC. AC power input is an IEC 320-type power inlet, 15A service connector. The
AC input side contains a front panel with provisions for mounting screw, two built-in handles to
extract the power supply, three status LEDs, and fans for power supply and system cooling.
2-28 OL-13208-03

• Cisco ASR 1002 Router DC Power Supply, page 2-31—The DC power supply operates between
–40.5VDC and –72VDC. Three-position euro-style terminal block, with labeled connections for –
(–48/60 V input) and + (–48/60 V Return) and the GND symbol for grounding. The DC input side
contains a front panel with provisions for mounting screw, built in handles to remove the power
Cisco ASR 1002 Router Power Supply Fans

Cisco ASR 1002 Router system level cooling is provided by two 12 VDC type fans in each power supply
module. The fans in each module provide system cooling back-up in the event of a single fan failure. In
addition, the fans in each of the power supplies can be powered from a single supply when only one unit
is operational. The airflow direction is front to back.
Statement 1005
Cisco ASR 1002 Router AC Power Supply

Router.
The Cisco ASR 1002 Router system level cooling is provided by two 12 VDC type fans in each of the
two power supply modules. The fans in each module are intended to provide system cooling back-up in
the event of a single fan failure. In addition, the fans in each of the power supplies can be powered from
a single supply when only one unit is operational. The airflow direction is front to back. The power
supplies plug directly into the Cisco ASR1000-RP1 and distributes power back to the midplane.
midplane and module mounted connectors. Two captive screws (tool operated latches) are provided on
Cisco ASR 1002 AC Power Supply LEDs and Connector
Figure 2-16 shows the AC power supplies at the rear of the Cisco ASR 1002 Router. The Cisco
of the chassis are described in Table 2-11.
OL-13208-03 2-29

1 2 3 4 5 6
OUTPUT INPUT FAN OUTPUT INPUT FAN

FAIL OK OK FAIL OK OK

This unit might have more than
to de-energize the unit. to de-energize the unit.
280288
1
8 7
1 Chassis ESD socket 5 AC power supply fan

2 AC power supply slot number 0 6 AC power supply captive installation screw
3 AC power supply On (I) /Off (O) switch 7 AC power supply slot number 1
Table 2-18 Cisco ASR 1002 Router Power Supply LEDs

INPUT OK Power supply activity Green LED illuminates green to signal that the power supply
None If LED is not illuminated, then the input voltage is less
than 70V or the power supply is turned off. For an AC
fail alarm.
2-30 OL-13208-03

AC Power System Output Voltage Alarm Range for Cisco ASR 1002
The AC power supply output voltage alarm occurs when the output voltage is below the low end of the
minimum or above the high end of the maximum limits shown inTable 2-19.
Table 2-19 Cisco ASR 1002 Router AC Power Supply Output Voltage Alarm Range
Minimum Maximum
12 V 10.0 to 11.2V 12.8 to 13.8 V
3.3 V 2.6 to 3.0V None
Cisco ASR 1002 Router DC Power Supply

Router. The recommended branch circuit breaker for the Cisco ASR 1002 Router DC power supply is
30Amp. Use an AWG #10 maximum wire gauge on the 30Amp circuit. The maximum branch circuit for
the DC power supply module must not exceed 30Amp.
The Cisco ASR 1002 Router has two of the same type power supplies in power supply slot 0 and power
supply slot 1. The power supply slot numbers are on the left side of the chassis and the power supplies
are located on the floor of the chassis. The power supply switch is a Standby switch and is not considered
a disconnect.
The DC input connector is a euro-style terminal block. The largest size gauge of wire that the front panel
euro-terminal block can accept is AWG #10 wire. The terminal block is compliant to all safety agencies
and electrical requirements of the power supply. Use the tie wraps to dress the input cable wires; there
are two tie wrap tabs on the DC power supply.
The DC power supply unit is secured into the system chassis with two captive screws mounted on the
faceplate.
Cisco ASR 1002 Router DC Power Supply LEDs and Connector
Figure 2-17 shows the DC power supplies at the rear of the Cisco ASR 1002 Router. The Cisco
of the chassis are described in the Table 2-20.
OL-13208-03 2-31

1 2 3 4 5 6


280289
1
-48V/-60V 16A -48V/-60V 16A
7
10 9 8
1 Chassis ESD socket 6 DC power supply captive installation screw

2 DC power supply slot 0 label 7 DC power supply slot 1 label
3 DC power supply switch Standby/On (I) 8 Earth ground lead
(standby symbol is a broken circle with a
vertical line through the top of it)
4 DC power supply LEDs 9 Positive lead
5 Fan 10 Negative lead

supply fan status
Output Fail alarm.
2-32 OL-13208-03

DC Power System Input for Cisco ASR 1002
The DC power supply operates within specification from –40.5VDC to –72VDC continuously once the
the power supply DC input turn on threshold of –43.5V has been reached. Table 2-21 shows the common
input ranges for reference only. The DC power input connector is a euro-style terminal block that accepts
three wires, one positive, one negative, and one grounding wire.
Table 2-21 Cisco ASR 1002 Router DC Power System Input
Voltage Range (VDC) Minimum Nominal Maximum

Domestic –40.5 –48 –56
International –55 –60 –72
DC Power System Output for Cisco ASR 1002
The DC power supply output tolerance is defined in Table 2-22 under all combinations of DC input line
variation. Total system power consumption should not exceed 470 watts or output rating of each power
supply.
Note Two power supplies are used for redundant operation. System total power consumption shall never
exceed rating of one power supply to maintain redundancy.
Table 2-22 Cisco ASR 1002 Router DC Power System Output Voltage and Current

Minimum –11.80 VDC –3.20 VDC
Nominal –12.00 VDC –3.30 VDC
Maximum –12.20 VDC –3.40 VDC
Output Current
Minimum –2.0 A –0.10 A
Maximum –39 A –3.125 A
OL-13208-03 2-33

2-34 OL-13208-03

C H A P T E R 3
Preparing Your Site for Installation
Before you install the Cisco ASR1000 Series Aggregation Services Routers, consider:
• The power and cabling requirements that must be in place at your installation site
• The equipment required to install the router
• The environmental conditions your installation site must meet to maintain normal operation
This chapter contains important safety information you should know before working with the Cisco
ASR 1000 Series Aggregation Services Routers and guides you through the process of preparing your
site for router installation.
Note Do not unpack the system until you are ready to install it. Keep the chassis in the shipping container to
prevent accidental damage until you determined an installation site. Use the appropriate unpacking
documentation included with the system.
This chapter contains the following sections:

• Safety Recommendations, page 3-2
• Safety Warnings, page 3-2
• Site Planning, page 3-7
• Preventing Electrostatic Discharge Damage, page 3-17
• Electrical Safety, page 3-18
• Receiving a Cisco ASR 1000 Series Router, page 3-19
• Chassis-Lifting Guidelines, page 3-20
• Tools and Equipment, page 3-21
• Checking the Shipping Container Contents, page 3-21
• Cisco ASR 1000 Series Router Installation Checklist, page 3-23
OL-13208-03 3-1

Chapter 3 Preparing Your Site for Installation
Safety Recommendations
Safety Recommendations
The following guidelines will help to ensure your own safety and protect your Cisco equipment. This list
does not cover all potentially hazardous situations, so be alert.
• Cisco safety policy is that all of its routers must conform to the requirements of IEC 60950, with
appropriate national deviations, as a minimum. In addition, Cisco routers must also meet the
requirements of any other normative documents (for example, standards, technical specifications,
laws or regulations).
• Review the safety warnings listed in the Regulatory Compliance and Safety Information for the
Cisco ASR 1000 Series Aggregation Services Routers that accompanied your Cisco ASR 1000 Series
Router, before installing, configuring, or maintaining the router.
• Never attempt to lift an object that might be too heavy for you to lift by yourself.
• Always turn all power supplies off and unplug all power cables before opening the chassis.
• Always unplug the power cable before installing or removing a chassis.
• Keep the chassis area clear and dust free during and after installation.
• Keep tools and chassis components away from walk areas.
• Do not wear loose clothing, jewelry (including rings and chains), or other items that could get caught
in the chassis. Fasten your tie or scarf and sleeves.
• The Cisco ASR 1000 Series Routers operate safely when it is used in accordance with its marked
electrical ratings and product usage instructions.
Safety Warnings
Read the installation instructions in this document before you connect the system to its power source.
Failure to read and follow these guidelines could lead to an unsuccessful installation and possibly
damage to the system and components.
You should observe the following safety guidelines when working with any equipment that connects to
electrical power or telephone wiring. These guidelines help you avoid injuring yourself or damaging the
devices.
Compliance Requirements
This section includes Safety Compliance and Network Equipment Building Systems (NEBS) standards.
The Cisco ASR1000 Series routers are in compliance with national and international standards as
described in Table 1.
3-2 OL-13208-03

Cautions and Regulatory Compliance Statements for NEBS
Table 1 NEBS Compliance Requirements
Safety Compliance and NEBS Requirements

Specification Description
Safety
Caution To comply with Class A emissions requirements, shielded-twisted pair T1/E1 cables
must be used with the 8-port channelized T1/E1 SPA interface in any Cisco ASR1000
Series chassis.
Telcordia NEBS
GR-1089-Core Statement
Caution To comply with the Telcordia GR-1089 NEBS standard for electromagnetic
compatibility and safety, for Ethernet RJ-45 ports, use only shielded Ethernet cables
that are grounded on both ends. In a NEBS installation, all Ethernet ports are limited
to intrabuilding wiring.
GR-1089
GR-63
Cautions and Regulatory Compliance Statements for NEBS

Table 2 lists cautions, regulatory compliance statements, and requirements for the Network
Equipment-Building System (NEBS) certification from the Telcordia Electromagnetic Compatibility
and Electrical Safety – Generic Criteria for Network Telecommunications Equipment (A Module of
LSSGR, FR-64; TSGR, FR-440; and NEBSFR, FR-2063) Telcordia Technologies Generic
Requirements, GR-1089-CORE, Issue 4, June 2006.
Table 2 NEBS Compliance Statements
Attach an ESD-preventive wrist strap to your wrist and to a bare metal surface.
Caution To comply with the Telcordia GR-1089 NEBS standard for

electromagnetic compatibility and safety, for Ethernet RJ-45 ports, use
only shielded Ethernet cables that are grounded on both ends. In a NEBS
installation, all Ethernet ports are limited to intrabuilding wiring.
Caution The intrabuilding ports of the equipment or subassembly is only suitable

for connection to intrabuilding or unexposed wiring or cabling. The
intrabuilding ports of the equipment or subassembly MUST NOT be
metallically connected to interfaces that connect to the OSP or its wiring.
These interfaces are designed for use only as intrabuilding interfaces
(Type 2 or Type 4 ports as described in GR-1089-CORE, Issue 4), and
require isolation from the exposed OSP cabling. The addition of primary
protectors is not sufficient protection in order to connect these interfaces
metallically to OSP wiring.
OL-13208-03 3-3

Standard Warning Statements
Table 2 NEBS Compliance Statements (continued)
Products that have an AC power connection are intended for deployments where an
external surge protective device (SPD) is used at the AC power service equipment as
defined by the National Electric Code (NEC).
This product is designed for a common bonding network (CBN) installation.
This product can be installed in a network telecommunication facility or location
where the NEC applies.
An electrical conducting path shall exist between the product chassis and the metal
surface of the enclosure or rack in which it is mounted or to a grounding conductor.
Electrical continuity shall be provided by using thread-forming type mounting
screws that remove any paint or nonconductive coatings and establish a
metal-to-metal contact. Any paint or other nonconductive coatings shall be removed
on the surfaces between the mounting hardware and the enclosure or rack. The
surfaces shall be cleaned and an antioxidant applied before installation.
The grounding architecture of this product is DC-isolated (DC-I).
DC-powered products have a nominal operating DC voltage of 48 VDC. Minimal
steady state DC operating voltage is 40 VDC. Reference American National
Standards Institute (ANSI) T1.315, Table 1.
Note The English warnings in this document are followed by a statement number. To see the translations of a
warning into other languages, look up its statement number in the Regulatory, Compliance, and Safety
Information for the Cisco Aggregation Services Router 1000 Series document.

This section describes the warning definition and then lists core safety warnings grouped by topic.
Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
each warning to locate its translation in the translated safety warnings that accompanied this device.
Note: SAVE THESE INSTRUCTIONS

Statement 1071
General Safety Warnings
Warning Read the installation instructions before you connect the system to its power source. Statement 1004
Warning Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
3-4 OL-13208-03

Warning No user-serviceable parts inside Do not open. Statement 1040
Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074
Warning To comply with the Class A emissions requirements shielded twisted pair T1/E1 cables must be used
for SPA-8-Port Channelized T1/E1 SPA (SPA-8XCHT1/E1) on the Cisco ASR1006, ASR1004, and ASR1002.
EN55022/CISPR22 Statement
Warning To comply with Class A emissions requirements- shielded management Ethernet, CON, and AUX
cables on the Cisco ASR1002 must be used.
Warning Power cable and AC adapter - When installing the product, please use the provided or designated
connection cables/power cables/AC adaptors. Using any other cables or adapters could cause a
malfunction or a fire. Electrical Appliance and Material Safety Law prohibits the use of certified
cables (that have the ‘UL’ shown on the code) for any other electrical devices than products
designated by Cisco. The use of cables that are certified by Electrical Appliance and Material Safety
Law (that have ‘PSE’ shown on the code) is not limited to Cisco-designated products. Statement 371
Warning Only trained and qualified personnel should be allowed to install or replace this equipment
Statement 1030
the protective device is rated not greater than: AC power supplies for the Cisco ASR 1004 Router, Cisco
ASR 1006 Router, and Cisco ASR 1002 Router: 120 VAC, 20A U.S. maximum. DC power supplies for the
Cisco ASR 1004 Router: 40A U.S. maximum. DC power supplies for the Cisco ASR 1006 Router: 50A U.S.
maximum. DC power supplies for the ASR 1002 Router: 30A U.S. maximum. Statement 1005
Warning This product requires short-circuit (overcurrent) protection to be provided as part of the building
installation. Install only in accordance with national and local wiring regulations. Statement 1045
Warning This unit may have more than one power supply connection. All connections must be removed to
de-energize the unit. Statement 1028
Warning The plug-socket combination must be accessible at all times, because it serves as the main
disconnecting device. Statement 1019
OL-13208-03 3-5

Warning Hazardous voltage or energy may be present on the DC power terminals. Always replace cover when
terminals are not in service. Be sure uninsulated conductors are not accessible when cover is in
place. Statement 1075
Warning Use copper conductors only. Statement 1025
Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection
authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024
Warning Hazardous voltage or energy is present on the backplane when the system is operating. Use caution
when servicing. Statement 1034
Warning Class 1 laser product. Statement 1008
Warning Class 1 LED product. Statement 1027
Warning Laser radiation is present when the system is open. Statement 1009
Warning Do not stare into the laser beam. Statement 1010
Warning Class I(CDRH) and Class 1M (IEC) laser products. Statement 1055
Warning Invisible laser radiation may be emitted from the end of the unterminated fiber cable or connector. Do
not view directly with optical instruments. Viewing the laser output with certain optical instruments
(for example, eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye
hazard. Statement 1056
Warning There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with
the same or equivalent type recommended by the manufacturer. Dispose of used batteries according
to the manufacturer’s instructions. Statement 1015
Warning Do not touch or bridge the metal contacts on the battery. Unintentional discharge of the batteries can
cause serious burns. Statement 341
3-6 OL-13208-03

Site Planning
Warning To prevent personal injury or damage to the chassis, never attempt to lift or tilt the chassis using the
handles on modules (such as power supplies, fans, or cards); these types of handles are not designed
to support the weight of the unit. Statement 1032
Warning To prevent the system from overheating, do not operate it in an area that exceeds the maximum
recommended ambient temperature of: 40 degrees C. Statement 1047
Warning This equipment must be externally grounded using a customer-supplied ground wire before power is
applied. Contact the appropriate electrical inspection authority or an electrician if you are uncertain
that suitable grounding is available. Statement 366
Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to
hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI)
that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not
operate the system unless all cards, faceplates, front covers, and rear covers are in place.
Site Planning
This section contains site planning information, and will help you plan for the installation of the
Cisco ASR 1000 Series routers. It contains the following sections:
• General Precautions, page 3-7
• Site Selection Guidelines, page 3-8
• Floor Loading Considerations, page 3-10
• Site Power Guidelines, page 3-10
• Site Cabling Guidelines, page 3-12
• Rack-Mounting and Location Guidelines, page 3-14
• Site Planning Checklist, page 3-17
General Precautions
Observe the following general precautions when using and working with your Cisco ASR1000 Series
system.
• Keep your system components away from radiators and heat sources and do not block cooling vents.
• Do not spill food or liquids on your system components and never operate the product in a wet
environment.
• Do not push any objects into the openings of your system components. Doing so can cause fire or
electric shock by shorting out interior components.
OL-13208-03 3-7

Site Planning
• Position system cables and power supply cables carefully. Route system cables and the power supply
cable and plug so that they cannot be stepped on or tripped over. Be sure that nothing else rests on
your system component cables or power cable.
• Do not modify power cables or plugs. Consult a licensed electrician or your power company for site
modifications. Always follow your local and national wiring rules.
• If you turn off your system, wait at least 30 seconds before turning it on again to avoid system
component damage.
Site Selection Guidelines

The Cisco ASR 1000 Series Routers require specific environmental operating conditions. Temperature,
humidity, altitude, and vibration can affect the performance and reliability of the router. The following
sections provide specific information to help you plan for the proper operating environment.
The Cisco ASR1000 Series Routers are designed to meet the industry EMC, safety, and environmental
standards described in the Regulatory, Safety, and Compliance Information for Cisco ASR 1000 Series
Aggregation Services Routers document.
Site Environmental Requirements

Environmental monitoring in the Cisco ASR1000 Series router protects the system and components from
damage caused by excessive voltage and temperature conditions. To ensure normal operation and avoid
unnecessary maintenance, plan and prepare your site configuration before installation. After installation,
make sure the site maintains the environmental characteristics as shown in Table 3-3.
Table 3-3 Cisco ASR 1000 Series Router Environmental Tolerances
Environmental Characteristic Minimum Maximum

Steady State Operating 0 degree C 50 degree C
(50 degrees C at 10,000
feet)
Storage –20 degrees C +70 degrees C
Humidity operating (noncondensing) 10% 90%
Humidity nonoperating (noncondensing) 5% 95%
Altitude operating: over allowable temperature –500 feet 10,000 feet
range (0 to 50 degrees C)
Altitude, nonoperating: over allowable temperature –1000 feet 50,000 feet
range
Thermal shock non-operating with change over time –25 degrees C +70 degrees C
of 3 minute
Thermal Shock - Operating at 2.5 degree C per 0 degrees C +50 degrees C
minute
Physical Characteristics
Be familiar with the physical characteristics of the Cisco ASR 1000 Series Router to assist you in placing
the system in the proper location.
3-8 OL-13208-03

Site Planning
Table 3-4 shows the weight and dimensions of the Cisco ASR 1000 Series Routers.
Table 3-4 Physical Characteristics of Cisco ASR 1000 Series Router
Characteristic Cisco ASR 1006 Router Cisco ASR 1004 Router Cisco ASR 1002 Router
Height 10.47 in. (26.543 cm) - 6.95 in. (17.653 cm) - 3.47 in. (8.813 cm) - 2RU
6RU rack-mount per EIA 4RU rack-mount per EIA rack-mount per EIA RS-310
RS-310 standard RS-310 standard
Width 17.25 in. (43.815 cm) - 19 17.25 (43.815 cm) - 19 17.25 in. (43.815 cm) -
inch rack-mount inch rack- mount or 19-inch rack-mount or
optional 23 Telco rack optional 23 Telco rack
mount mount
Depth 22.50 in. (57.15 cm) 22.50 in.(57.15 cm) 22.50 in. (57.15 cm)
(including card handles, (including card handles, (including card handles,
cable-management cable-management cable-management brackets,
brackets, power supply brackets, and power and power supply handles)
handles). supply handles) for mounting in a
600mm-enclosed cabinet
Weight of fully 75 lbs (34.019 kg) 50 lbs (22.679 kg) 40 lbs (18.143 kg)
configured
chassis
The following list describes additional Cisco ASR 1000 Series chassis characteristics:
• Cisco ASR 1006 Router:
– Chassis height meets EIA-310 rack spacing 6RU (10.47/266mm), universal rack mount
– Chassis width meets EIA-310 19inch (17.25/438.15mm) wide with rack brackets
– Cable-management brackets at each Cisco ASR 1000 Series SPA Interface (SIP) locations can
hold 16 ports of STP/UTP RJ 45 cables
– Cable-management brackets allow for 1.5 inch bend radii for cables
– Adjustable rack mount brackets allow for a front to rear rail variance distance of 15.50/394mm
to 19.00/482.6mm
– Chassis height meets EIA-310 rack spacing 4RU (6.95 in/176.53mm), universal rack mount
– Cable-management brackets at each Cisco ASR 1000 Series SPA Interface (SIP) locations can
hold 16 ports of STP/UTP RJ 45 cables
to 19.00/482.6mm
– Chassis height meets EIA-310 rack spacing 2RU (3.47 in/ 88.138mm), universal rack mount
– Cable-management brackets at the Cisco ASR 1002 Router location can hold 16 ports of
STP/UTP RJ 45 cables
OL-13208-03 3-9

Site Planning
to 19.00/482.6mm
Floor Loading Considerations

Ensure that the floor under the rack supporting the Cisco 1000 Series Routers is capable of supporting
the combined weight of the rack and all other installed equipment.
To assess the weight of the fully configured Cisco 1000 Series Router respectively, refer to Table 3-4.
For additional information about floor loading requirements, consult the document GR-63-CORE,
Network Equipment Building System (NEBS) Requirements: Physical Protection.
Site Power Guidelines

The Cisco 1000 Series Router has specific power and electrical wiring requirements. Adhering to these
requirements ensures reliable operation of the system. Follow these precautions and recommendations
when planning your site the Cisco ASR 1000 Series Router:
• The redundant power option provides a second, identical power supply to ensure that power to the
chassis continues uninterrupted if one power supply fails or input power on one line fails.
• In systems configured with the redundant power option, connect each of the two power supplies to
a separate input power source. If you fail to do this, your system might be susceptible to total power
failure due to a fault in the external wiring or a tripped circuit breaker.
• To prevent a loss of input power, be sure the total maximum load on each circuit supplying the power
supplies is within the current ratings of the wiring and breakers.
• Check the power at your site before installation and periodically after installation to ensure that you
are receiving clean power. Install a power conditioner if necessary.
• Provide proper grounding to avoid personal injury and damage to the equipment due to lightning
striking power lines or due to power surges. The chassis ground must be attached to a central office
or other interior ground system.
Caution This product requires short-circuit (overcurrent) protection, to be provided as part of the building
installation. Install only in accordance with national and local wiring regulations.
Note The Cisco 1000 Series Router installation must comply with all applicable codes and is approved for use
with copper conductors only. The ground bond fastening hardware should be of compatible material and
preclude loosening, deterioration, and electrochemical corrosion of hardware and joined material.
Attachment of the chassis ground to a central office or other interior ground system must be made with
an AWG #6 gauge wire, copper ground conductor at a minimum.
Electrical Circuit Requirements

Each Cisco 1000 Series Router requires a dedicated electrical circuit. If you equip it with dual power
feeds, provide a separate circuit for each power supply to avoid compromising the power redundancy
feature.
3-10 OL-13208-03

Site Planning
The Cisco ASR 1000 Series Routers can be powered by a DC or AC source. Ensure that the equipment
grounding is present and observe power strip ratings. Make sure that the total ampere rating of all
products plugged into the power strip does not exceed 80% of the rating.
Table 3-5 contains specifications for DC powered systems for all Cisco ASR 1000 Series Routers.
Cisco ASR 1000

Series Router DC
Cisco ASR 1004 24 30 40 10 8
Cisco ASR 1002 16 20 30 12 10
The AC and DC power supplies for the Cisco ASR 1000 Series Routers support different types of power
supply switches. Table 3-6 defines which power supplies the Cisco ASR 1000 Series routers support (a
Standby or an On/Off switch).
Table 3-6 Cisco ASR 1000 Series Routers AC and DC Power Supply Switches
Switch Type
Supported
Symbol Cisco ASR 1000 Series Router Power Supply
On/Off circuit I/O ASR 1006 DC
ASR 1004 DC
ASR 1002 AC
Standby Switch A broken ASR 1006 AC
circle with
ASR 1004 AC
a vertical
line ASR 1002 DC
through the
top of it
Table 3-7 lists AC and DC power supply system rating requirements for all Cisco ASR 1000 Series
Routers.
OL-13208-03 3-11

Site Planning
Table 3-7 AC and DC Power Supply System Rating Specifications for the Cisco ASR 1000 Series Routers
Power supply declared ratings AC = 100-240 VAC
DC = –48/ –60 VDC
Line frequency rating 50/60 Hz
Site Cabling Guidelines

This section contains guidelines for wiring and cabling at your site. When preparing your site for
network connections to the Cisco 1000 Series Router, consider the type of cable required for each
component, and the cable limitations. Consider the distance limitations for signaling, EMI, and
connector compatibility. Possible cable types are fiber, thick or thin coaxial, foil twisted-pair, or
unshielded twisted-pair cabling.
Also consider any additional interface equipment you need, such as transceivers, hubs, switches,
modems, channel service units (CSUs), or data service units (DSUs).
Note The E1 interface on the Cisco 8-Port Channelized T1/E1 SPA interface uses RJ-48c receptacles for E1
(120-Ohm) cables with RJ-45 connectors. You can use all ports simultaneously. Each E1 connection
supports interfaces that meet the G.703 standards. The RJ-45 connection does not require an external
transceiver. The E1 ports are E1 interfaces that use 120-ohm shielded twisted-pair (STP) cables.
Warning Shielded T1/E1 cables must be used to comply with FCC/EN55022/CISPR22 Class A emissions
requirements on the 8-port channelized T1/E1 SPA interface.
Before you install the Cisco 1000 Series Router, have all additional external equipment and cables on
hand. For ordering information, contact a customer service representative.
The extent of your network and the distances between network interface connections depend in part on
the following factors:
• Signal type
• Signal speed
• Transmission medium
The distance and rate limits referenced in the following sections are the IEEE-recommended maximum
speeds and distances for signaling purposes. Use this information as a guideline in planning your
network connections prior to installing the Cisco 1000 Series Router.
If wires exceed recommended distances, or if wires pass between buildings, give special consideration
to the effect of a lightning strike in your vicinity. The electromagnetic pulse caused by lightning or other
high-energy phenomena can easily couple enough energy into unshielded conductors to destroy
electronic devices. If you have had problems of this sort in the past, you may want to consult experts in
electrical surge suppression and shielding.
3-12 OL-13208-03

Site Planning
Asynchronous Terminal Connections

The route processor provides a console port to connect a terminal or computer for local console access.
The RP1 also provides an auxiliary port to connect to a modem for remote dial-in console access.
Both ports have RJ-45 connectors, support RS-232 asynchronous data, and have distance
recommendations specified in the IEEE RS-232 standard.
Interference Considerations
When wires are run for any significant distance, there is a risk that stray signals will be induced on the
wires as interference. If interference signals are strong, they can cause data errors or damage to the
equipment.
The following sections describe sources of interference and how to minimize its effects on the
Cisco 1000 Series Router system.
Electromagnetic Interference
All equipment powered by AC current can propagate electrical energy that can cause electromagnetic
interference (EMI) and possibly affect the operation of other equipment. The typical sources of EMI are
equipment power cords and power service cables from electric utility companies.
Strong EMI can destroy the signal drivers and receivers in the Cisco 1000 Series Router and even create
an electrical hazard by causing power surges through power lines into installed equipment. These
problems are rare, but could be catastrophic.
To resolve these problems, you need specialized knowledge and equipment, which could consume
substantial time and money. However, you should ensure that you have a properly grounded and shielded
electrical environment, paying special attention to the need for electrical surge suppression.
Table 3-8 lists electrode magnetic compliance standards for the Cisco ASR 1000 Series Aggregation
Services Routers.
Table 3-8 EMC Standards
EMC Standards FCC 47 CFR Part 15 Class A

VCCI Class A
AS/NSZ Class A
ICES-003 Class A
EN55022/CISPR 22 Information Technology Equipment
(Emissions)
EN55024/CISPR 24 Information Technology Equipment
(Immunity)
EN300 386 Telecommunications Network Equipment
(EMC)
EN50082-1/EN61000-6-1 Generic Immunity Standard
CE marking UL60950-1
CSA C22.2 No. 60950-1-03
EN 60950-1
OL-13208-03 3-13

Site Planning
Table 3-8 EMC Standards
IEC 60950-1
AS/NZS 60950.1
Radio Frequency Interference
When electromagnetic fields act over a long distance, radio frequency interference (RFI) can be
propagated. Building wiring can often act as an antenna, receiving the RFI signals and creating more
EMI on the wiring.
If you use twisted-pair cable in your plant wiring with a good distribution of grounding conductors, the
plant wiring is unlikely to emit radio interference. If you exceed the recommended distances, use a
high-quality twisted-pair cable with one ground conductor for each data signal.
Lightning and AC Power Fault Interference
If signal wires exceed recommended cabling distances, or if signal wires pass between buildings, you
should consider the effect that a lightning strike in your vicinity might have on the Cisco 1000 Series
Router.
The electromagnetic pulse (EMP) generated by lightning or other high-energy phenomena can couple
enough energy into unshielded conductors to damage or destroy electronic equipment. If you have
previously experienced such problems, you should consult with RFI/EMI experts to ensure that you have
adequate electrical surge suppression and shielding of signal cables in your Cisco 1000 Series Router
operating environment.
Rack-Mounting and Location Guidelines

The Cisco 1000 Series Router is designed for standalone, two-post 19 inch rack-mount, four-post 19 inch
rack-mount and closed cabinet systems with front and rear doors. You can mount the Cisco 1000 Series
Router on an equipment shelf or tabletop.
The sections that follow describe criteria for selecting a rack to mount the Cisco 1000 Series Router,
guidelines for placing the rack for reliable operation, and safety precautions to take to prevent bodily
injury when mounting a Cisco ASR1000 Series system in a rack.
Precautions for Rack-Mounting

The following rack-mount guidelines are provided to ensure your safety:
• Do not move large racks by yourself. Due to the height and weight of a rack, a minimum of two
people are required to accomplish this task.
• Ensure that the rack is level and stable before extending a component from the rack.
• Ensure that proper airflow is provided to components in the rack.
• Do not step or stand on any component or system when servicing other systems or components in a
rack.
• When mounting the Cisco 1000 Series Router in a partially filled rack, load the rack from the bottom
to the top with the heaviest component at the bottom of the rack.
• If the rack is provided with stabilizing devices, then install the stabilizers before mounting or
servicing the unit in the rack.
3-14 OL-13208-03

Site Planning
Rack Selection Guidelines

The Cisco 1000 Series Router can be mounted in most two-post or four-post, 19-inch equipment racks
that comply with the Electronics Industries Association (EIA) standard for equipment racks (EIA-310-D
19-inch). The rack must have at least two posts with mounting flanges to mount the chassis.
Caution When mounting a chassis in any type of rack equipment, make certain the inlet air to the chassis does
not exceed 55C.
The distance between the center lines of the mounting holes on the two mounting posts must be 18.31
inches ± 0.06 inch (46.50 cm ± 0.15 cm). The rack-mounting hardware included with the chassis is
suitable for most 19-inch equipment racks.
We recommend that you mount the Cisco 1000 Series Router in an equipment rack which includes the
necessary rack-mounting hardware which is suitable for most 19-inch equipment racks.
Consider installing the Cisco 1000 Series Router in a rack with the following features:
• NEBS compliant, 19-inch (48.3 cm) wide rack.
• EIA or ETSI hole patterns in the mounting rails. Required mounting hardware is shipped with the
Cisco 1000 Series Router. If the rack that you plan to install the system in has metric-threaded rails,
you must provide your own metric mounting hardware.
• Perforated top and open bottom for ventilation to prevent overheating.
• Leveling feet for stability.
Note The Cisco 1000 Series Router should not be installed in an enclosed rack because the chassis requires
an unobstructed flow of cooling air to maintain acceptable operating temperatures for its internal
components. Installing the router in any type of enclosed rack—even with the front and back doors
removed—could disrupt the air flow, trap heat next to the chassis, and cause an overtemperature
condition inside the router. If you use an enclosed rack, make certain that there are air vents on all sides
of the rack and there is proper ventilation.
Equipment Rack Guidelines

The placement of the rack can affect personnel safety, system maintenance, and the system ability to
operate within the environmental characteristics described in Table 3-3 on page 3-8. Choose a proper
location for the Cisco 1000 Series Router by following the guidelines below.
Locating for Safety
If the Cisco 1000 Series Router is the heaviest or the only piece of equipment in the rack, consider
installing it at or near the bottom to ensure that the rack center of gravity is as low as possible.
For additional information about the proper placement of electronic equipment, consult the document
GR-63-CORE, Network Equipment Building System (NEBS) Requirements: Physical Protection.
Locating for Easy Maintenance
Keep at least 3 feet of clear space in front and behind the rack. This space ensures that you can remove
the Cisco 1000 Series Router components and perform routine maintenance and upgrades easily.
OL-13208-03 3-15

Site Planning
Avoid installing the Cisco 1000 Series Router in a congested rack and consider how the routing of cables
from other pieces of equipment in the same rack could affect access to the routers cards.
The front and top of the chassis must remain unobstructed to ensure adequate airflow and prevent
overheating inside the chassis.
Allow the following clearances for normal system maintenance:
• At the top of the chassis—At least 3 inches (7.6 cm)
• In the front of the chassis—3 to 4 ft (91.44 cm to 121.92 cm)
To avoid problems during installation and ongoing operation, follow these general precautions when you
plan the equipment locations and connections:
• Use the show environment all command regularly to check the internal system status. The
environmental monitor continually checks the interior chassis environment; it provides warnings for
high temperature and creates reports on any occurrences. If warning messages are displayed, take
immediate action to identify the cause and correct the problem.
• Keep the Cisco 1000 Series Router off of the floor and out of areas that collect dust.
• Follow ESD prevention procedures to avoid damage to equipment. Damage from static discharge
can cause immediate or intermittent equipment failure.
Locating for Proper Airflow
Ensure the location of the Cisco 1000 Series Router has enough airflow to keep the system operating
within the environmental characteristics and the air temperature is sufficient to compensate for the heat
dissipated by the system.
Avoid locating the Cisco 1000 Series Router in a location in which the chassis air intake vents could
draw in the exhaust air from adjacent equipment. Consider how the air flows through the Cisco 1000
Series Router. The Cisco 1000 Series Router airflow direction is front to back with ambient air drawn in
from the venting located on the chassis front sides.
3-16 OL-13208-03

Preventing Electrostatic Discharge Damage
Site Planning Checklist

Table 3-9 is provided to help you perform and account for all the site planning tasks presented in this
appendix.
Table 3-9 Site Planning Checklist
Site Planning Requirements

The site meets the environmental requirements.
The site air conditioning system can compensate for the heat dissipation of the Cisco ASR
1000 Series.
The floor space that the Cisco ASR 1000 Series Routers occupy can support the weight of
the system).
Electrical service to the site complies with the requirements.
The electrical circuit servicing the Cisco ASR 1000 Series complies with the requirements).
Consideration has been given to the console port wiring, and limitations of the cabling
involved, according to TIA/EIA-232F.
The Cisco 1000 Series Router Ethernet cabling distances are within limitations.
The equipment rack in which you plan to install the Cisco ASR 1000 Series chassis complies
with requirements.
Careful consideration has be given to safety, ease of maintenance, and proper airflow in
selecting the location of the rack.
Preventing Electrostatic Discharge Damage

Electrostatic discharge (ESD) damage, occurs when electronic cards or components are improperly
handled and can result in complete or intermittent failures. The performance routing engine (PRE), and
all line cards consist of a printed circuit card that is fixed in a metal carrier. Electromagnetic interference
(EMI) shielding and connectors are integral components of the carrier. Although the metal carrier helps
to protect the cards from ESD, use an antistatic strap each time you handle the modules. Handle the
carriers by the edges only; never touch the cards or connector pins.
Caution Always tighten the captive installation screws on all system components when you are installing them.
These screws prevent accidental removal of the module, provide proper grounding for the system, and
help to ensure that the bus connectors are properly seated in the backplane.
Static electricity can harm delicate components inside your system. To prevent static damage, discharge
static electricity from your body before you touch any of your system components, such as an
microprocessor. As you continue to work on your system, periodically touch an unpainted metal surface
on the computer chassis.
Following are guidelines for preventing ESD damage:
• Always use an ESD-preventive wrist or ankle strap and ensure that it makes good skin contact.
Before removing a card from the chassis, connect the equipment end of the strap to the ESD plug at
the bottom of the chassis below the power entry modules (Figure 3-1).
OL-13208-03 3-17

Electrical Safety
• Handle line cards by the faceplates and carrier edges only; avoid touching the card components or
any connector pins.
• When removing a card, place the removed module component-side-up on an antistatic surface or in
a static-shielding bag. If the module will be returned to the factory, immediately place it in a
static-shielding bag.
• Avoid contact between the modules and clothing. The wrist strap protects the card from ESD
voltages on the body only; ESD voltages on clothing can still cause damage.
• When transporting a sensitive component, first place it an antistatic container or packaging.
• Handle all sensitive components in a static-safe area. If possible, use antistatic floor pads and
workbench pads.
Caution For safety, periodically check the resistance value of the antistatic strap. The measurement should be
between 1 and 10 ohms.
Figure 3-1 ESD Chassis Grounding Stud
280034
2 1
1 Chassis earth ground studs and lead wire 3 Earth ground connector on the chassis
2 Grounding screws 4 Earth ground symbol
Electrical Safety
All system components are hot-swappable. They are designed to be removed and replaced while the
system is operating without presenting an electrical hazard or damage to the system.
Follow these basic guidelines when you are working with any electrical equipment:
• Before beginning any procedures requiring access to the chassis interior, locate the emergency
power-off switch for the room in which you are working.
3-18 OL-13208-03

Receiving a Cisco ASR 1000 Series Router
• Disconnect all power and external cables before installing or removing a chassis.
• Do not work alone when potentially hazardous conditions exist.
• Never assume that power has been disconnected from a circuit; always check.
• Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.
Never install equipment that appears damaged.
• Carefully examine your work area for possible hazards such as moist floors, ungrounded power
extension cables, and missing safety grounds.
In addition, use the guidelines that follow when working with any equipment that is disconnected from
a power source but is still connected to telephone wiring or other network cabling.
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is specifically designed for wet
locations.
• Never touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.
Statement 1001
Receiving a Cisco ASR 1000 Series Router

Each Cisco ASR1000 Series chassis is shipped in a container that is strapped to a pallet as illustrated in
Figure 3-2.
OL-13208-03 3-19

Chassis-Lifting Guidelines
Figure 3-2 Cisco ASR 1000 Series Router Packaged for Shipping
132823
3
1 Outside carton 3 Packing straps

2 Pallet
Note We recommend that you have at least two people available to help with the installation and ensure safe
lifting.
Chassis-Lifting Guidelines
The fully configured system weighs approximately 75 pounds. The chassis is not intended to be moved
frequently. Before you install the system, ensure that your site is properly prepared so you can avoid
having to move the chassis later to accommodate power sources and network connections.
Two or more people are required to lift the chassis. Each time you lift the chassis or any heavy object,
follow these guidelines:
• Never attempt to lift the chassis by yourself. Because of the size and weight of the chassis, use at
least two people to safely lift and move it without causing injury or damaging the equipment.
• Ensure that your footing is solid, and balance the weight of the chassis between your feet.
• Lift the chassis slowly; never move suddenly or twist your body as you lift.
• Keep your back straight and lift with your legs, not your back. If you must bend down to lift the
chassis, bend at the knees, not at the waist, to reduce the strain on your back muscles.
• Do not remove installed components from the chassis.
• Always disconnect all external cables before lifting or moving the chassis.
3-20 OL-13208-03

Tools and Equipment
Step 1 Each person should stand on either side of the chassis and place one hand under the air intake at the
bottom front of the chassis.
Step 2 With the other hand, grasp the top rear of the chassis under the air exhaust and carefully lift the chassis.
Tools and Equipment

The tools and equipment listed below are recommended as the minimum necessary to install the
Cisco ASR 1000 Series Router. You may need additional tools and equipment to install associated
equipment and cables. You may also require test equipment to check electronic and optical signal levels,
power levels, and communications links.
• Phillips hand screwdriver
• A 3.5mm flat-blade screwdriver
• Tape measure (optional)
• Level (optional)
• Power drill
Unpacking and Verifying Shipping Contents

When you receive your chassis, perform the following steps and use the shipping contents checklist from
the next section:
Step 1 Inspect the box for any shipping damage. (if there is damage contact your service representative).
Step 2 Unpack the Cisco ASR 1000 Series Router.
Step 3 Perform a visual inspection of the chassis.
Step 4 After you have unpacked the system verify that you have received all of the required components. Using
the packing list as a guide, take the following steps to check the contents of the Cisco ASR 1000 Series
Router shipping container:
Step 5 Check the contents of the boxes containing accessory items. Verify that you have received all equipment
listed in your order.
Step 6 Check that all Cisco ASR 1000 Series RP1s, Cisco ASR1000-ESP10s, Cisco ASR1000-ESP5, Cisco
ASR 1000 Series SPA Interface (SIP), and power supplies you ordered are installed in the chassis.
Ensure that the configuration matches the packing list.
Checking the Shipping Container Contents

Use the components list to check the contents of the Cisco ASR 1000 Series Router shipping container.
Do not discard the shipping container. You need the container if you move or ship the Cisco ASR 1000
Series Router in the future.
OL-13208-03 3-21

Checking the Shipping Container Contents
Table 3-10 Cisco ASR 1000 Series Router Shipping Container Contents List
Component Description Received

Chassis Cisco ASR 1000 Series Router configured with dual AC or dual DC
power supplies and a shared port adapter blank panel if a shared port
adapter has not been ordered.
Accessories Kit Front and rear chassis rack-mount brackets that you will attach to the
chassis with the respective screws
Three sets of screws, one set for:
• Front rack-mount brackets (use the black screws)
• Rear rack-mount brackets (use the package with the 5 screws)
• Cable-management brackets (use the 4 screw package)
Two cable-management brackets with ‘U’ feature design devices
attached; a different size for each chassis.
ESD, Wrist Strap (disposable) 1 disposable wrist strap
Documentation Regulatory Compliance and Safety Information for Cisco Aggregation
Services 1000 Series Chassis document
Optional Equipment Power cord if an AC power supply was shipped. There are none for the
DC power supply units.
Note Most Cisco documentation is online or on the Cisco Documentation DVD. Documentation that ships
with your Cisco ASR1000 Series router includes the Regulatory Compliance and Safety Information for
the Cisco Aggregation Services Router 1000 Series document, and the Cisco Aggregation Services
Router 1000 Series Documentation Roadmap that contains documentation titles and the URLs to them
online. See also the “Related Documentation” section on page xviii.
3-22 OL-13208-03

Cisco ASR 1000 Series Router Installation Checklist

To assist you with your installation and to provide a historical record of what was done by whom,
photocopy the Cisco ASR 1000 Series Router Installation Checklist. Use this to indicate when each
procedure or verification is completed. When the checklist is completed, place it in your site log along
with the other records for your new router.
Table 3-11 Cisco ASR 1000 Series Router Installation Checklist
Verified
Task By Date
Date chassis received
Chassis and all accessories unpacked
Types and numbers of interfaces verified
Safety recommendations and guidelines reviewed
Installation Checklist copied
Site log established and background information entered
Site power voltages verified
Site environmental specifications verified
Required passwords, IP addresses, device names, and so on, available
Required tools available
Network connection equipment available
Cable-management bracket installed (optional but recommended)
AC power cable(s) connected to AC source(s) and router
DC power cable(s) connected to DC source(s) and router
Network interface cables and devices connected
System power turned on
System boot complete (STATUS LED is on)
Shared port adapters are operational
Correct hardware configuration displayed after system banner appears
OL-13208-03 3-23

3-24 OL-13208-03

C H A P T E R 4
Cisco ASR 1006 Router Overview and Installation
This chapter describes the Cisco ASR 1006 Router and provides the procedures for installing the
Cisco ASR 1006 Router on an equipment shelf or tabletop or in equipment racks. It also describes how
to connect interface and power cables.
• General Rack Installation Guidelines, page 4-4
• Guidelines for an Equipment Shelf or Tabletop Installation, page 4-5
• Equipment Shelf or Tabletop Installation, page 4-6
• Rack-Mounting a Cisco ASR 1006 Router, page 4-8
• Attaching the Cable-Management Bracket, page 4-16
• Attaching a Chassis Ground Connection, page 4-17
• Connecting Power to Cisco ASR 1006 Router, page 4-21
• Connecting a Terminal to the Cisco ASR 1000 Series RP1 Console Port, page 4-27
• Connecting System Cables, page 4-29
Cisco ASR 1006 Router Description

The Cisco ASR 1006 Router supports full-width card modules. It is designed with a single midplane with
connectors on one interface midplane. The Cisco ASR 1006 Router supports:
• Three Cisco ASR 1000 Series SPA Interface Processor (SIP)
• Twelve SPA slots
• Two Cisco ASR 1000 Series Embedded Services Processor (Cisco ASR1000-ESP10 or Cisco
ASR1000-ESP20)
• Two Cisco ASR 1000 Series Route Processor 1 (RP1)
• Dual (redundant) AC and DC power supplies
• Front View, page 4-2
• Rear View, page 4-2
OL-13208-03 4-1

Chapter 4 Cisco ASR 1006 Router Overview and Installation
Front View
Figure 4-1 Cisco ASR 1006 Router —Front View
Cisco ASR 1006

ASR1000-SIP10
C/A
C/A
C/A
C/A
C/A
C/A
C/A
C/A
US
US
AT
AT
A/L
A/L
A/L
A/L
A/L
A/L
A/L
A/L
ST
ST
3
C/A
C/A
C/A
C/A
C/A
C/A
C/A
C/A
2 2
US
US
AT
AT
A/L
A/L
A/L
A/L
A/L
A/L
A/L
A/L
ST
ST
3
PWR STATUS
ASR1000-SIP10
C/A
C/A
C/A
C/A
C/A
C/A
C/A
C/A
US
US
AT
AT
A/L
A/L
A/L
A/L
A/L
A/L
A/L
A/L
ST
ST
6 0
3
C/A
C/A
C/A
C/A
C/A
C/A
C/A
C/A
1 1
US
US
AT
AT
A/L
A/L
A/L
A/L
A/L
A/L
A/L
A/L
ST
ST
0
3
PWR STATUS
ASR1000-SIP10
C/A
C/A
C/A
C/A
C/A
C/A
C/A
C/A
US
US
AT
AT
A/L
A/L
A/L
A/L
A/L
A/L
A/L
A/L
ST
ST
5
0
3
C/A
C/A
C/A
C/A
C/A
C/A
C/A
C/A
0 0
US
US
AT
AT
A/L
A/L
A/L
A/L
A/L
A/L
A/L
A/L
ST
ST
0
3
PWR STATUS
4 F1
PWR
STAT
ACTV
STBY
F1
ASR1000-ESP10
3 F0
PWR
STAT
ACTV
STBY
F0
ASR1000-ESP10
CRIT HD
2 PWR ACTV MAJ USB

O
AC
STAT STBY MIN BF CARRIER LINK

R1 ASR1000-RP1 0 1 DISK BITS MGMT ETHERNET CON AUX
R1
CRIT HD
280032
1 PWR ACTV MAJ USB
O
AC
STAT STBY MIN BF CARRIER LINK

R0 ASR1000-RP1 0 1 DISK BITS MGMT ETHERNET CON AUX R0
3 Slot FP0 with ASR 1000 Series ESP 7 ASR 1000 Series SIP slot 2
4 Slot FP1 with ASR 1000 Series ESP
Rear View
Figure 4-2 shows the rear of the Cisco ASR 1006 Router with an AC power supplies installed.
4-2 OL-13208-03

Figure 4-2 Cisco ASR 1006 Router Rear View With AC Power Supply
6 7 8
OUTPUT INPUT INPUT

FAIL OK OK
ALARMS
60V
1A MAX
100-240V~ 16-7A
50-60HZ
280029
4
3 2 1

2 AC power supply DB-25 alarm connector—A 6 AC power inlet
female DB-25 D-sub connector which enables
you to attach an external alarm monitoring
facility to the router, thus supporting a
telco-style of handling alarm conditions in the
router.
3 Cable tie wrap tabs 7 AC power supply Standby switch (standby
through the top of it). A Standby switch is not
considered a disconnect.
4 AC power supply captive screws 8 AC power supply LEDs
Internal fans draw cooling air into the chassis and across internal components to maintain an acceptable
operating temperature. (See Figure 4-2.) The fans are located at the rear of the chassis. A two-hole
grounding lug is located on the side of the chassis. Two power supplies, either two AC power supplies
or two DC power supplies, are accessed from the rear of the router.
Note You have already unpacked your chassis and read all the site requirements for your new equipment.
Proceed with the installation.
Note Do not combine AC and DC power supplies in the same chassis.
Statement 1071
OL-13208-03 4-3

Installation Methods
Warning Before you install, operate, or service the system, read the Regulatory Compliance and Safety
Information for Cisco ASR 1000 Series Aggregation Services Routers publication. This document
provides important safety information you should know before working with the system. Statement 200
Although rack-mounting is the preferred method of installation for the Cisco ASR 1006 Router, you can
mount the chassis:
• On an equipment shelf or tabletop
• In a19-inch wide (standard), 4-post equipment rack or two-post, using the rack-mount brackets in
the accessory kit
Note The Cisco ASR 1006 Router usually ships fully loaded. However, you can remove components from the
chassis to make the chassis lighter for your rack installation.
General Rack Installation Guidelines

When planning your rack installation, consider the following guidelines:
• The Cisco ASR 1006 Router requires a minimum of 7 rack units (22.3 inches or 56.6 cm) of vertical
rack space. Measure the proposed rack location before mounting the chassis in the rack.
• Before using a particular rack, check for obstructions (such as a power strip) that could impair
rack-mount installation. If a power strip does impair a rack-mount installation, remove the power
strip before installing the chassis, and then replace it after the chassis is installed.
• Allow sufficient clearance around the rack for maintenance. If the rack is mobile, you can push it
back near a wall or cabinet for normal operation and pull it out for maintenance (installing or moving
cards, connecting cables, or replacing or upgrading components). Otherwise, allow 19 inches (48.3
cm) of clearance to remove field-replaceable units.
• Maintain a minimum clearance of 3 inches (7.62 cm) on the front, top, and sides of the chassis for
the cooling air inlet and exhaust ports, respectively. Avoid placing the chassis in an overly congested
rack or directly next to another equipment rack; otherwise, the heated exhaust air from other
equipment can enter the inlet air vents and cause an overtemperature condition inside the router.
Caution To prevent chassis overheating, never install a Cisco ASR 1006 Router in an enclosed room that is not
properly ventilated or air conditioned.
• Always install heavier equipment in the lower half of a rack to maintain a low center of gravity to
prevent the rack from falling over.
4-4 OL-13208-03

Guidelines for an Equipment Shelf or Tabletop Installation
• Install and use the cable-management brackets included with the Cisco ASR 1006 Router to keep
cables organized and out of the way of the cards and processors. Ensure that cables from other
equipment already installed in the rack do not impair access to the cards or require you to disconnect
cables unnecessarily to perform equipment maintenance or upgrades.
• Install rack stabilizers (if available) before you mount the chassis.
• Provide an adequate chassis ground (earth) connection for your router chassis.
In addition to the preceding guidelines, review the precautions for avoiding excessive temperature
conditions in the “Electrical Safety” section on page 3-18.
Table 4-1 provides the Cisco ASR 1006 Router dimensions and weight information.
Table 4-1 Cisco ASR 1006 Router Dimensions and Weight
Cisco ASR 1006 Dimensions

Depth 22.50 in. (57.15 cm)
(including card handles, cable-management brackets, power
supply handles).
Height 10.45 in. (26.543 cm) - 6RU rack-mount per EIA RS-310
standard
Width 17.25 in. (43.815 cm) - 19 inch rack-mount
Weight 75 lb (34.019 kg) - fully configured

The chassis should already be in the area where you will install it. If you have not determined where to
install your chassis, see Cisco ASR 1000 Series Routers Components, page 2-1 for information about
site considerations.
If you are not rack-mounting your Cisco ASR1000 series chassis, place it on a sturdy equipment shelf
or tabletop.
When installing the Cisco ASR 1006 Router on an equipment shelf or tabletop, ensure that the surface
is clean and that you have considered the following:
• The Cisco ASR 1006 Router requires at least 3 inches (7.62 cm) of clearance at the inlet and exhaust
vents (the front and top/rear sides of the chassis).
• The Cisco ASR 1006 Router should be installed off the floor. Dust that accumulates on the floor is
drawn into the interior of the router by the cooling fans. Excessive dust inside the router can cause
overtemperature conditions and component failures.
• There must be approximately 19 inches (48.3 cm) of clearance at the front and rear of the chassis to
install and replace FRUs, or to access network cables and equipment.
• The Cisco ASR 1006 Router needs adequate ventilation. Do not install it in an enclosed cabinet
where ventilation is inadequate.
• Have the cable-management bracket available if you plan to install it on the front of the chassis.
• An adequate chassis ground (earth) connection exists for your router chassis (see the “Attaching a
Chassis Ground Connection” section on page 4-17).
• Always follow proper lifting practices as outlined in the “Chassis-Lifting Guidelines” section on
page 3-20, when handling the chassis.
OL-13208-03 4-5

Equipment Shelf or Tabletop Installation

To mount your Cisco ASR 1006 Router on an equipment shelf or tabletop, follow these steps.
Step 1 Remove any debris and dust from the tabletop or platform, as well as the surrounding area.
Step 2 Lift the chassis into position on the equipment shelf or tabletop.
Warning At least two people are required to lift the chassis onto a tabletop or platform. To prevent injury, keep
your back straight and lift with your legs, not your back. Statement 164
Figure 4-3 Lifting the Chassis
FANS
FAN
OK MULTI-
FAILURE
FAN
FAILURE
When hot CAUTION

removal swapping
this fan
be done and replaceme tray,
system in under two nt must
shutdown minutes
will occur. or
1
2
3
4
0A
CISCO PROC 0B
ESSOR
10000 CISCO ONLY 5
10000 CISCO
6
FAIL
10000 CISCO
7
FAIL
10000 CISCO
8
FAIL
10000 CISCO
FAIL
10000
CISCO
10000 CISCO
10000 CISCO
FAIL
10000 CISCO
FAIL
CO
10000
FAIL
NS
OLE CO
FAIL
NS
CAR
OLE
ALA
AUX
CAR
RIER
LOO
RM
ALA
RIER
LOO
P
AUX
RM
0
P
0 ACT
IVIT
CAR
ETH Y ACT
ALA
CAR
IVIT
RIER
ER
LOO
SLO
ALA
LIN
RM
NE ETH
SLO
Y
RIER
CAR
LOO
K T
P
RM
1 ER
T
ALA
0
T
SLO
RIER
LIN
0
NE
LOO
SLO
1
1 0
RM
K T
T
P
T
0
0
1
2 1
2 1
POWER 1
FAULT
MISWIR 3
E 2
3 2
LINK
CAR
TX
ALA
RX
2
RIER
LOO
RM
4 3
4 3
3
5
CAR
4
5 4
RIER
TX
4
RX
5
5
5
GIGABIT ETHERNET
PERFORMANCE ROUTING ENGINE

CH OC-12-DSO SM-IR
AC
O
AC
CR O
6XCT3–DS0
ITIC
CR
6XCT3–DS0
MA AL
ITIC
JO
R MA AL
MIN
JO
OR
OC–12/STM–4 POS SM–IR
POWER MIN
R
OR
6XCT3–DS0
FAULT
6XCT3–DS0
MISWIR
6XCT3–DS0
STA
TU
FAI S STA
L TU
FAI S
L
PROC
ESSOR
ONLY
30007
Note The chassis in Figure 4-3 does not represent the Cisco ASR 1000 Series Router. This is only an example
of how to lift a Cisco chassis.
Step 1 Attach the front rack-mount brackets. Locate the threaded holes in the front sides of the chassis (first
holes beyond the vent holes) and use the package of black screws that shipped with the chassis.
Step 2 Align the front rack-mount bracket to one side of the chassis.
Step 3 Insert and tighten the screws on one side.
Step 4 Repeat Step 2 through Step 3 on the other side of the chassis. Use at least 4 screws to secure the
rack-mount brackets to the chassis.
Note The cable-management brackets are installed on the chassis after you install the chassis rack-mount
brackets.
4-6 OL-13208-03

Step 5 Obtain the two cable-management brackets and screws shipped with your chassis. Figure 4-4 shows
attached cable-management brackets on the front of the Cisco ASR 1006 Router. when the chassis is
placed on a table top or equipment shelf.
Note Make certain that the cable-management ‘U’ feature device has the open end pointing upwards
when you attach it to the chassis
Figure 4-4 Attaching the Cable-Management Brackets to the Cisco ASR 1006 Router
US
C/
AT
A
ST
A/L
C/
A
A/L
C/
-POS
SPA-4XOC3
A/L
C/
3
A/L
US
C/
AT
1
ST
A/L
C/
0
A/L
A
US
C/
-POS
C/
SPA-4XOC3
AT
A/L
A
ST
C/
A/L
C/
3
A/L
A
A/L
C/
-POS
2
SPA-4XOC3
A/L
C/
1
3
A/L
0
2
US
C/
AT
US
C/
1
ST
AT
A/L
C/
ST
A/L
C/
0
A/L
C/
-POS
SPA-4XOC3
A/L
C/
-POS
A
SPA-4XOC3
A/L
C/
A/L
C/
3
A/L
A/L
US
C/
1
AT
1
ST
A/L
C/
0
A/L
A
US
C/
-POS
C/
SPA-4XOC3
AT
A/L
A
ST
C/
A/L
C/
3
A/L
A
A/L
C/
-POS
2
SPA-4XOC3
A
A/L
C/
1
3
A/L
A
2
US
A
US
C/
C/
3
AT
AT
A
1
ST
A
ST
A/L
A/L
C/
C/
A
0
A/L
A/L
C/
C/
-POS -POS
SPA-4XOC3 SPA-4XOC3
A
A
A/L
A/L
C/
C/
3
3
A/L
A/L
A
2
US
C/
AT
1
A
1
ST
A/L
C/
0
A
0
A/L
A
US
C/
-POS
C/
SPA-4XOC3
AT
A/L
A
ST
C/
A/L
C/
3
A/L
A
A/L
C/
-POS
2
SPA-4XOC3
A
A/L
C/
1
3
A/L
0
2
US
C/
AT
1
ST
A/L
C/
0
A/L
C/
-POS
SPA-4XOC3
A
A/L
C/
3
A/L
2
1
0
280036
2
1 Cable-management screws 3 Chassis front rack-mount bracket

2 Cable-management bracket
Step 6 Screw the cable-management bracket to each side of the rack-mount brackets already attached to the
chassis. Use two screws for each cable-management bracket. Use the package of four screws.
Step 7 Check that all screws are securely tightened.
Step 8 Go to the “Attaching a Chassis Ground Connection” section on page 4-17 to continue the installation.
OL-13208-03 4-7

Rack-Mounting a Cisco ASR 1006 Router

The Cisco ASR 1006 Router can be installed with both front or rear rack-mount brackets. The chassis
rack-mounting flanges are secured directly to the chassis before you lift it into the rack. For installing
Cisco ASR 1006 Router rack-mount brackets, go to:
• “Chassis Front Rack-Mount Brackets” section on page 4-9
• “Chassis Rear Rack-Mount Brackets” section on page 4-10
Verifying Rack Dimensions

Before you install the chassis, measure the space between the vertical mounting flanges (rails) on your
equipment rack to verify that the rack conforms to the measurements shown in Figure 4-5.
Step 1 Mark and measure the distance between two holes on the left and right mounting rails.
The distance should measure 18.31 inches ± 0.06 inches (46.5 cm ± 0.15 cm).
Note Measure for pairs of holes near the bottom, middle and top of the equipment rack to ensure that
the rack posts are parallel.
Step 2 Measure the space between the inner edges of the left front and right front mounting flanges on the
equipment rack.
The space must be at least 17.7 inches (45 cm) to accommodate the chassis which is
17.25 inches (43.8 cm) wide and fits between the mounting posts on the rack.
Figure 4-5 Verifying Equipment Rack Dimensions
Mounting flanges
Minimum usable
aperture 17.7 inches
(45.0 cm)
28014
Hole centerline
to hole centerline
18.31 inches ± 0.06 inches
(46.5 cm ± 0.15 cm)
4-8 OL-13208-03

Attaching the Chassis Rack-Mount Brackets

This section explains how to attach the front and rear rack-mount brackets to the chassis. Before
installing the chassis in the rack, you must install the rack-mount brackets on each side of the chassis.
The parts and tools required for installing the rack-mount brackets and cable-management brackets are
listed in the “Tools and Equipment” section on page 3-21.
brackets and mount the chassis in the rack.
Chassis Front Rack-Mount Brackets

Determine where in the rack you want the chassis to be mounted. If you are mounting more than one
chassis in the rack, then start from the bottom up or the center of the rack. Figure 4-6 shows the brackets
attached to the chassis. Depending on the bracket holes you use, the chassis may protrude in the rack.
To install the front rack-mount brackets on a Cisco ASR 1006 Router, complete the following steps:
Step 1 Locate the threaded holes on the side of the chassis. Make certain that you hold the front rack-mount
bracket with the ear and holes facing outward and towards the front of the chassis (see Figure 4-6).
Figure 4-6 Attaching the Front Rack-Mount Brackets to the Cisco ASR 1006 Router
C/A
A/L C/A
A/L C/A
0
A/L C/A
2 1
A/L ASR1000-S
IP10
2
US
C/A
STAT
3 SPA-4XOC3-PO
A/L C/A
A/L C/A
S C/A
Cisco ASR
0
1
A/L C/A
A/L C/A
A/L C/A
1006
A/L 0
2 A/L C/A
US
1
STAT
3 SPA-4XOC3-PO A/L
2
US
S C/A
STAT
C/A 3 SPA-4XOC3-PO
A/L C/A A/L C/A S
PWR STATU
C/A
S A/L C/A
A/L 0
0 A/L C/A
A/L C/A
1 1
A/L ASR1000-S
IP10
1
2
A/L
US
2
US
STAT
C/A
STAT
3 3 SPA-4XOC3-PO
A/L C/A
A/L C/A
SPA-4XOC3-PO
S C/A
S
2
0 A/L C/A
A/L C/A
1 A/L C/A
A/L 0
2 A/L C/A
US
1
STAT
3 SPA-4XOC3-PO A/L
2
US
S C/A
STAT
C/A 3 SPA-4XOC3-PO
A/L C/A A/L C/A S
PWR STATU
C/A S A/L C/A
A/L 0
0 A/L C/A
A/L C/A
0 1
A/L ASR1000-S
IP10
1
2
A/L
US
2
US
STAT
C/A
STAT
3 3 SPA-4XOC3-PO
A/L C/A
A/L C/A
SPA-4XOC3-PO
S C/A
S
1
0 A/L C/A
A/L C/A
1 A/L C/A
A/L 0
2 A/L C/A
US
1
STAT
3 SPA-4XOC3-PO A/L
2
US
S C/A
STAT
3 SPA-4XOC3-PO
PWR A/L C/A S
ACTV PWR STATU
F1 STAT
STBY
S
0
A/L C/A
A/L C/A
1
ASR1000-ESP A/L
10 2
US
STAT
3 SPA-4XOC3-PO
S
0
PWR
ACTV
F0 STAT
STBY
ASR1000-ESP
10
PWR
CRIT F1
ACTV MAJ
STAT HD
R1 ASR1000-R
STBY MIN AC
O
USB
P1
BF
0 1 DISK
CRIT
PWR CARRIER
ACTV MAJ
R0 STAT
STBY MIN AC
O HD
BITS
LINK F0
ASR1000-R USB MGMT ETHERN
P1 ET
CON
BF AUX
0 1 DISK
CARRIER
LINK
BITS
MGMT ETHERN
R1
280035
ET
CON
AUX
R0
4 3 2 1
1 Front rack-mount bracket screws 3 Front rack-mount bracket ear and holes
2 Front rack-mount bracket 4 Chassis side vent location
OL-13208-03 4-9

Step 2 Position the front rack-mount bracket top hole with the chassis first top hole behind the side vent holes
(see Figure 4-6).
Step 3 Insert and tighten the black screws on one side.
Step 4 Repeat Step 1 through Step 3 on the other side of the chassis. Use black screws to secure the rack-mount
brackets to the chassis.
Step 5 Install the chassis in the rack. To install the Cisco ASR 1006 Router in a rack, go to Installing the Cisco
ASR 1006 Router in a Rack, page 4-12.
This completes the steps for attaching the front rack-mount brackets to the Cisco ASR 1006 Router.
Chassis Rear Rack-Mount Brackets

If you are rack mounting the chassis using the rear rack-mount brackets, then this type of installation
provides for the chassis being recessed in the rack.
Step 1 Locate the threaded holes on the rear side of the chassis. Make certain that you hold the rear t rack-mount
bracket with the ear and holes facing outward and towards the rear of the chassis (see Figure 4-7).
Figure 4-7 shows where to attach the rear rack-mount brackets to the Cisco ASR 1006 Router.
4-10 OL-13208-03

Figure 4-7 Attaching the Rear Rack-Mount Brackets to the Cisco ASR 1006 Router
1 2
1
3
280038
0
1 Rear rack-mount bracket ear and holes 3 Rear rack-mount bracket components that
slide into rear bracket attached to the chassis
2 Rear rack-mount bracket 4 Rear rack-mount bracket screws
Step 2 Position the rear rack-mount bracket top hole with the chassis second top hole from the back (See
Figure 4-7).
Step 4 After the bracket is secured to the side of the chassis, slide the two remaining components into the side
rack-mount bracket.
Step 5 Repeat Step 1 through Step 3 on the other side of the chassis. Use all the screws to secure the rear
This completes the steps for attaching the rear rack-mount brackets to the Cisco ASR 1006 Router.
Caution Before you mount the ASR 1006 Router in a rack, make certain you read which rack-mount bracket ear
holes to use when positioning the chassis in the rack. As a result of using the designated ear holes on the
rack-mount bracket, the cable-management bracket installation will be made easier. For
cable-management installation instructions, go to Attaching the Cable-Management Bracket, page 4-16.
OL-13208-03 4-11

Installing the Cisco ASR 1006 Router in a Rack

After installing the rack-mount brackets on the chassis, you mount the chassis by securing the
rack-mount brackets to two posts or mounting strips in the rack using the screws provided. Because the
rack-mount brackets support the weight of the entire chassis, be sure to use all screws to fasten the two
rack-mount brackets to the rack posts.
Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special
precautions to ensure that the system remains stable. The following guidelines are provided to ensure
your safety:
-This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
-When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the
heaviest component at the bottom of the rack.
-If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing
the unit in the rack. Statement 1006
We recommend that you allow at least 1 or 2 inches (2.54 or 5.08 cm) of vertical clearance between the
router and any equipment directly above and below it.
To install the chassis in the rack, complete the following steps:
Step 1 On the chassis, ensure that all screw fasteners on the installed components are securely tightened.
Step 2 Make sure that your path to the rack is unobstructed. If the rack is on wheels, ensure that the brakes are
engaged or that the rack is otherwise stabilized. See the next sections on the types of racks you can use
to install the chassis.
Step 3 (Optional) Install a shelf in the rack to support the Cisco ASR 1006 Router. If you use a shelf, this will
help support the chassis while you secure it to the rack.
Step 4 With two people, lift the chassis into position between the rack posts.
Step 5 Align the mounting bracket holes with the rack post holes and attach the chassis to the rack.
Note If you are using a shelf then raise the chassis to the level of the shelf. Let the bottom of the
chassis rest on the brackets, but continue to support the chassis.
Step 6 Position the chassis until the rack-mounting flanges are flush against the mounting rails on the rack.
Step 7 Hold the chassis in position against the mounting rails and follow these steps:
a. Insert the bottom screw into the third hole up from the bottom of the rack mount ear and use a
hand-held screwdriver to tighten the screw to the rack rail.
Tip In the next step, insert the top screw diagonally from the bottom screw that you just attached.This helps
with keeping the chassis in place.
b. Insert the top screw into the third hole down from the top of the rack mount ear and tighten the screw
to the rack rail.
c. Insert a screw in the middle of the rack-mount bracket on both sides of the chassis.
d. Repeat these steps for the other side of the chassis.
4-12 OL-13208-03

Note As a result of using the specified rack-mount bracket ear holes, the cable-management bracket
can be easily attached to the rack-mount bracket when the chassis is in the rack.
Step 8 Tighten all screws on each side to secure the chassis to the equipment rack.
You can install your Cisco AR1006 chassis in a two-post rack or a four-post rack. See the “Two-Post
Rack Installation” section on page 4-13 and the four-post rack installation, go to the “Four-Post Rack
Installation” section on page 4-14.
Two-Post Rack Installation

The Cisco ASR 1006 Router can be installed in a two-post rack, either 19 inch or 23 inch.
Figure 4-8 Installing the Cisco ASR 1006 Router in a Two-Post Equipment Rack
A
C/
L A
A/ C/
L A
A/ C/
0 L A
2 1
A/ C/
A/
L ASR1000-SIP10
2
TUS
A
C/
STA
L A 3 SPA-4XOC3-POS
A/ C/
L A
C/
A
Cisco ASR
0
1
A/ C/
A/
L
C/
A
A/
L
C/
A/
A
L
C/
A
100 6
L 0
A/ L A
2
TUS
A/ C/
1
STA
3 L
SPA-4XOC3-POS A/
2
TUS
A A
C/
STA
C/ 3
L A L A SPA-4XOC3-POS
C/ A/ C/
A/
PWR STATUS L A
L A A/ C/
A/ C/
0 0 L A
L A A/ C/
11 1
A/ C/
A/
L ASR1000-SIP10
1
2
A/
L
TUS
2
TUS
A
STA
C/
STA
3 3 SPA-4XOC3-POS
A/
L
C/
A/
A
L
C/
A
SPA-4XOC3-POS
C/
A 2
L A
0 L A
A/ C/
A/ C/ L A
1 L
A/ C/
A/ 0 L A
2
TUS
A/ C/
1
STA
3 L
SPA-4XOC3-POS A/
2
TUS
A A
C/
STA
C/ 3
C/ A/ C/
A/
PWR STATUS L A
L A A/ C/
A/ C/
0 0 L A
L A A/ C/
00 1
A/ C/
A/
L ASR1000-SIP10
1
2
A/
L
TUS
2
TUS
A
STA
C/
STA
3 3 SPA-4XOC3-POS
A/
L
C/
A/
A
L
C/
A
SPA-4XOC3-POS
C/
A 1
L A
0 L A
A/ C/
A/ C/ L A
1 L
A/ C/
A/ 0 L A
2
TUS
A/ C/
1
STA
3 L
SPA-4XOC3-POS A/
2
TUS
A
C/
STA
3 SPA-4XOC3-POS
PWR A/
L
C/
A
ACTV PWR STATUS A
L
F1 STAT
STBY 0
A/ C/
A/
L
C/
A
1
ASR1000-ESP10 A/
L
2
TUS
STA
3 SPA-4XOC3-POS
0
PWR
ACTV
F0 STAT
STBY
ASR1000-ESP10
280085
PWR
CRIT F1
ACTV MAJ
STAT HD
R1
R1 STBY MIN
ASR1000-RP1
AC
O
USB
BF
0 1 DISK
CRIT
PWR CARRIER
ACTV MAJ
R0 STAT O HD LINK F0
R0 STBY MIN
ASR1000-RP1
AC
USB
BITS
MGMT ETHERNET
CON
BF AUX
0 1 DISK
CARRIER
LINK
BITS
MGMT ETHERNET
R1
CON
AUX
R0
2 1
1 Cisco ASR1006 Router front rack-mount 2 Two-post equipment rack rail

bracket
Note Inner clearance (the width between the inner sides of the two posts or rails) must be at least 19 inches
(48.26cm). The height of the chassis is 10.45 inches (26.543 cm). Airflow through the chassis is from
front to back.
OL-13208-03 4-13

Caution If you are using a two-post rack secure the rack to the floor surface to prevent tipping and avoid bodily
injury and component damage.
Step 1 Position the chassis so the front is closest to you and lift it carefully into the rack. To prevent injury,
avoid any sudden twists or moves.
Step 2 Slide the chassis into the rack, pushing it back until the brackets meet the mounting strips or posts on
both sides of the rack.
Step 3 Keeping the brackets flush against the posts or mounting strips, align the holes in the brackets with the
holes on the rack or mounting strip.
Step 4 For each bracket, insert and tighten two screws to the rack on both sides.
Note Use the third hole up from the bottom of the rack-mount bracket and the third hole down from
the top of the rack-mount bracket. See Figure 4-10 for position and location of the ear holes on
the rack-mount bracket.
This completes the procedure for installing the chassis in a two-post rack. Proceed to the “Attaching a
Chassis Ground Connection” section on page 4-17 to continue the installation.
Four-Post Rack Installation

The Cisco ASR 1006 Router can be flush-mounted in a 19-inch equipment rack using the rack-mounting
kit provided with your system. The Cisco ASR 1006 Router can be mounted into the rack using two
recommended methods:
• Installing the chassis in an existing rack with equipment.
• Installing an empty chassis in a rack with no equipment installed.
4-14 OL-13208-03

Figure 4-9 Installing the Cisco ASR 1006 Router in a Four-Post Equipment Rack
A
C/
L A
A/ C/
L A
A/ C/
0 L A
2 1
A/ C/
A/
L ASR1000-SIP10
2
TUS
A
C/
STA
L A 3 SPA-4XOC3-POS
A/ C/
L A
C/
A
Cisco ASR
0
1
A/ C/
A/
L
C/
A
A/
L
C/
A/
A
L
C/
A
1006
L 0
A/ L A
2
TUS
A/ C/
1
STA
3 L
SPA-4XOC3-POS A/
2
TUS
A A
C/
STA
C/ 3
C/ A/ C/
A/
PWR STATUS L A
L A C/
2
A/ C/ A/
0 0 L A
L A A/ C/
11 1
A/ C/
A/
L ASR1000-SIP10
1
2
A/
L
TUS
2
TUS
STA
C/
STA
3 3 SPA-4XOC3-POS
A/
L
C/
A/
A
L
C/
A
SPA-4XOC3-POS
C/
A 2
L A
0 L A
A/ C/
A/ C/ L A
1 L
A/ C/
A/ 0 L A
2
TUS
A/ C/
1
STA
3 L
SPA-4XOC3-POS A/
2
TUS
A A
C/
STA
C/ 3
C/ A/ C/
A/
PWR STATUS L A
L A A/ C/
A/ C/
0 0 L A
L A A/ C/
00 1
A/ C/
A/
L ASR1000-SIP10
1
2
A/
L
TUS
2
TUS
STA
C/
STA
3 3 SPA-4XOC3-POS
A/
L
C/
A/
A
L
C/
A
SPA-4XOC3-POS
C/
A 1
L A
0 L A
A/ C/
A/ C/ L A
1 L
A/ C/
A/ 0 L A
2
TUS
A/ C/
1
STA
3 L
SPA-4XOC3-POS A/
2
TUS
A
C/
STA
3 SPA-4XOC3-POS
PWR A/
L
C/
A
ACTV PWR STATUS A
L
F1 STAT
STBY 0
A/ C/
A/
L
C/
A
1
ASR1000-ESP10 A/
L
2 TUS
STA
3 SPA-4XOC3-POS
0
PWR
ACTV
F0 STAT
STBY
ASR1000-ESP10
PWR
CRIT F1
ACTV MAJ
STAT HD
R1
R1 STBY MIN
ASR1000-RP1
AC
O
USB
BF
0 1 DISK
CRIT
PWR CARRIER
ACTV MAJ
R0 STAT O HD LINK F0
R0 STBY MIN
ASR1000-RP1
AC
USB
BITS
MGMT ETHERNET
CON
BF AUX
0 1 DISK
CARRIER
LINK
BITS
MGMT ETHERNET
R1
CON
AUX
R0
280084
4 3
1 Four-post equipment rack rear rail 3 Cisco ASR1006 front rack-mount brackets
2 Cisco ASR1006 rear rack-mount brackets 4 Four-post equipment rack front rail
When handling the chassis, always follow proper lifting practices, see Chassis-Lifting Guidelines, page
3-20.
front to back.
Note Make sure the rack is stabilized.
Step 1 (Optional) Install a shelf in the rack to support the Cisco ASR 1006 Router. If you are using a shelf then
raise the chassis to the level of the shelf. Let the bottom of the chassis rest on the brackets, but continue
to support the chassis.Using two people, lift the chassis into the rack using the side handles and grasping
underneath the power supply bays.
OL-13208-03 4-15

Attaching the Cable-Management Bracket
Note Use the third hole up from the bottom of the rack-mount bracket and the third hole down from the top
of the rack-mount bracket. See Figure 4-10 for position and location of the ear holes on the rack-mount
bracket.
Step 3 Hold the chassis in position against the mounting rails while the second person finger-tightens a screw
to the rack rails on each side of the chassis.
Step 4 Finger-tighten 4 more screws to the rack rails on each side of the chassis.
Step 6 Use a level to verify that the tops of the two brackets are level, or use a measuring tape to verify that both
brackets are the same distance from the top of the rack rails.
This completes the procedure for installing the chassis in the rack. Proceed to the “Attaching the
Cable-Management Bracket” section on page 4-16 to continue the installation.

The cable-management brackets mount to each rack-mount bracket on the chassis to provide
cable-management to both sides of the chassis (parallel with card orientation). These brackets are screw
mounted to the rack-mount brackets to allow easy installation and removal of cables.
The cable-management brackets for the Cisco ASR 1006 Router contain 5 independent
cable-management “U” type features with four screws and provides cable dressing of each card module
slots. For Cisco ASR 1000 SIPs, these brackets work in tandem with shared port adapter product feature
cable-management device to allow installation and removal of adjacent cards without the need to remove
cables.
Note Make certain that the cable-management bracket “U” type feature is facing upwards when you attach it
to the chassis.
Follow these steps to attach the cable-management brackets to both sides of the Cisco ASR 1006 Router
in the rack:
Step 1 Align the cable-management bracket to the rack-mount bracket on one side of the Cisco ASR 1006
Router. The cable-management bracket aligns to the top hole of the chassis rack-mount bracket.
Step 2 Using a Phillips screwdriver, insert the screw through cable-management bracket and into the chassis
rack-mount and tighten the screw.
Note Use the package of screws that came with your chassis containing four screws.
Step 3 Using the bottom rack-mount ear hole, insert the screw through cable-management bracket and into the
chassis rack-mount (see Figure 4-10).
4-16 OL-13208-03

Attaching a Chassis Ground Connection
Figure 4-10 shows the cable-management brackets attached to the chassis in a rack.
Figure 4-10 Installing the Cable-Management Bracket
US
C/
AT
A
ST
A/L
C/
A
A/L
C/
-POS
SPA-4XOC3
A/L
C/
3
A/L
US
C/
AT
1
ST
A/L
C/
0
A/L
A
US
C/
-POS
C/
SPA-4XOC3
AT
A/L
A
ST
C/
A/L
C/
3
A/L
A
A/L
C/
-POS
2
SPA-4XOC3
A/L
C/
1
3
A/L
0
2
US
C/
AT
US
C/
1
ST
AT
A/L
C/
ST
A/L
C/
0
A/L
C/
-POS
SPA-4XOC3
A/L
C/
-POS
A
SPA-4XOC3
A/L
C/
A/L
C/
3
A/L
A/L
US
C/
1
AT
1
ST
A/L
C/
0
A/L
A
US
C/
-POS
C/
SPA-4XOC3
AT
A/L
A
ST
C/
A/L
C/
3
A/L
A
A/L
C/
-POS
2
SPA-4XOC3
A/L
C/
1
3
A/L
A
2
US
A
US
C/
C/
3
AT
AT
A
1
ST
A
ST
A/L
A/L
C/
C/
A
0
A/L
A/L
C/
C/
-POS -POS
SPA-4XOC3 SPA-4XOC3
A
A
A/L
A/L
C/
C/
3
3
A/L
A/L
A
2
US
C/
AT
1
A
1
ST
A/L
C/
0
A
0
A/L
A
US
C/
-POS
C/
SPA-4XOC3
AT
A/L
A
ST
C/
A/L
C/
3
A/L
A
A/L
C/
-POS
2
SPA-4XOC3
A/L
C/
1
3
A/L
0
2
US
C/
AT
1
ST
A/L
C/
0
A/L
C/
-POS
SPA-4XOC3
A
A/L
C/
3
A/L
2
1
0
280036
2
1 Cable-management bracket screw location 3 Chassis front rack-mount bracket and ear
holes
This completes the procedure for installing the cable-management brackets on the chassis.

Connecting the Cisco ASR 1006 Router chassis to earth ground is required for all DC powered
installations and any AC powered installation where compliance with Telcordia grounding requirements
is necessary.
OL-13208-03 4-17

Caution The dual-lug chassis stud must be installed, the SIP and SPA must be fully inserted and screwed in and
earthed to prevent a potential hazard in a telecom line.
Have the recommended tools and supplies available before you begin this procedure.
Figure 4-11 shows the cable-management brackets attached to the chassis in a rack.
Figure 4-11 Installing the Cisco ASR 1006 Router Ground Connection
280034
2 1
1 Chassis earth ground studs and lead wire 3 Earth ground connector on the chassis
2 Grounding screws 4 Earth ground symbol
Before you connect power or turn on power to your chassis, you must provide an adequate chassis ground
(earth) connection for the chassis. A chassis ground connector is provided on each Cisco ASR 1006
Router. There is a stud on the side of the chassis and on the DC power supply (primary grounding stud).
Caution The grounding wire is always the first to be installed or connected and the last to be removed or
disconnected.
4-18 OL-13208-03

Recommended Tools and Supplies

The following tools, equipment, and supplies necessary to connect the system ground to the chassis:
• Phillips screwdriver
• Dual-lug chassis ground component
• Grounding wire
Use the following procedure to attach the grounding lug to the chassis ground connector on your chassis:
Step 1 Use the wire stripper to strip one end of the AWG #6 wire approximately 0.75 inches (19.05 mm).
Step 2 Insert the AWG #6 wire into the wire receptacle on the grounding lug.
Step 3 Use the crimping tool to carefully crimp the wire receptacle around the wire; this step is required to
ensure a proper mechanical connection.
Step 4 Attach the grounding lug with the wire so that the grounding wire does not overlap the power supply.
Figure 4-12 Attaching a Grounding Lug to the Chassis Ground Connector
1 2
280186
4
1 Chassis ground lead wire 3 Ground screws

2 Grounding stud 4 Chassis ground connector holes
Step 5 Locate the chassis ground connector on the side of your chassis.
Step 6 Insert the two screws through the holes in the grounding lug.
Step 7 Use the Number 2 Phillips screwdriver to carefully tighten the screws until the grounding lug is held
firmly to the chassis. Do not overtighten the screws.
Step 8 Connect the opposite end of the grounding wire to the appropriate grounding point at your site to ensure
an adequate chassis ground.
This completes the procedure for attaching a chassis ground connection. Go to the following cabling
sections for information on attaching cables.
OL-13208-03 4-19

Connecting Shared Port Adapter Cables

The instructions for connecting the cables for the shared port adapter installed in the Cisco ASR 1006
Router are contained in the respective configuration documents for each port adapter. For example, if
you are connecting the optical fiber cables for the PA-POS-OC3 port adapter, refer to the configuration
note PA-POS-OC3 Packet OC-3 Port Adapter Installation and Configuration Guide at
http://www.cisco.com/univercd/cc/td/doc/product/core
Shared port adapter documents are also available on the Cisco Documentation DVD.
Connecting Console and Auxiliary Port Cables

The Cisco ASR 1006 Router has a DCE-mode console port for connecting a console terminal and a
DTE-mode auxiliary port for connecting a modem or other DCE device (such as another router) to your
chassis. Figure 4-13 shows the CON and AUX ports on the Cisco ASR 1000 Series RP1 route processor
card.
Figure 4-13 Cisco ASR 1000 Series RP1—CON and AUX Ports
1 2
A
0
A/L
A
US
C/
-POS
C/
SPA-4XOC3
AT
A/L
A
ST
C/
A/L
C/
3
A/L
A
A/L
C/
-POS
2
SPA-4XOC3
A
A/L
C/
1
3
A/L
0
2
US
C/
AT
1
ST
A/L
C/
0
A/L
C/
-POS
SPA-4XOC3
A
A/L
C/
3
A/L
2
1
0
280181
AUX
LINK CON
NET
HD CARRIER MGMT ETHER
BITS
USB
CRIT
DF
ACTV MAJ
O
AC
PWR DISK
1
STBY MIN 0
STAT
ASR1000-RP1
1 CON connector 2 AUX connector
Note Both the console and the auxiliary ports are asynchronous serial ports; any devices connected to these
ports must be capable of asynchronous transmission. (Asynchronous is the most common type of serial
device; for example, most modems are asynchronous devices.)
The Cisco ASR 1006 Router uses RJ-45 ports for both the auxiliary port and the console port.
For console and auxiliary port pinouts for the RJ-45 connector, see Appendix A, “Cisco ASR 1006
Router Specifications.” Both ports are configured as asynchronous serial ports.
Step 1 Before connecting a terminal to the console port, configure the terminal to match the chassis console
port as follows: 9600 baud, 8 data bits, no parity, 1 stop bits (9600 8N1).
Step 2 After you establish normal router operation, you can disconnect the terminal.
4-20 OL-13208-03

Connecting Power to Cisco ASR 1006 Router
Connecting the Ethernet Management Port Cable

When using the Fast Ethernet Management port in the default mode (speed-auto and duplex-auto) the
port operates in auto-MDI/MDI-X mode. The port automatically provides the correct signal connectivity
through the Auto-MDI/MDI-X feature. The port automatically senses a crossover or straight-through
cable and adapts to it.
However, when the Fast Ethernet Management port is configured to a fixed speed (10 or 100 Mbps)
through command-line interface (CLI) commands, the port is forced to MDI mode.
When in a fixed-speed configuration and MDI mode:
• Use a crossover cable to connect to an MDI port
• Use a straight-through cable to connect to an MDI-X port

Warning The covers are an integral part of the safety design of the product. Do not operate the unit without the
covers installed. Statement 1077
Warning When you install the unit, the ground connection must always be made first and disconnected last.
Statement 1046
Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit.
Statement 1003
Statement 1030
This section provides the procedures for connecting AC-input and DC-input power to your Cisco ASR
1006 Router.
OL-13208-03 4-21

The DC power supply for the Cisco ASR 1006, ASR 1004, and ASR 1002 routers operate at individual
specifications. Table 4-2 shows the common input ranges and circuit breaker requirements.
Cisco ASR 1000

Series Router DC
Cisco ASR 1004 24 30 40 10 8
Cisco ASR 1002 16 20 30 12 10
Note Detailed instructions for removing and replacing the Cisco ASR1000 Series AC and DC power supplies
are in Removing and Replacing a Cisco ASR 1006 Router Power Supply, page 8-22 .
Connecting AC-Input Power to Cisco ASR 1006 Router

Follow these steps to connect an AC-input power supply to the Cisco 1006 chassis:
Step 1 At the rear of the chassis, check that the power switch on the power supply is in the Standby position.
Step 2 Plug the power cable into the inlet.
Note For additional AC power cable strain relief, secure the cable to the power supply handle by
inserting a nylon cable tie through the hole in the handle and around the cable.
4-22 OL-13208-03

Figure 4-14 Cisco ASR 1006 Router AC Power Supply Power Inlet and Standby Switch
6 7 8
OUTPUT INPUT INPUT

FAIL OK OK
ALARMS
60V
1A MAX
100-240V~ 16-7A
50-60HZ
280029
4
3 2 1

2 DB-25 alarm connector 6 AC power inlet
3 Tie-wrap tab 7 AC power supply Standby switch
4 AC power supply captive screw 8 AC power supply LEDs
Step 3 Plug the AC power supply cable into the AC power source.
This completes the procedure for connecting AC-input power.
Connecting DC-Input Power to Cisco ASR 1006 Router

This section describes how to connect the DC power supply into the Cisco ASR 1006 Router.
Before you begin, read these important notices:
• The color coding of the DC-input power supply leads depends on the color coding of the DC power
source at your site. Typically, green or green/yellow is used for ground (GND), black is used for
-48V on negative (–) terminal and red is used for RTN on the positive (+) terminal. Make certain the
lead color coding you choose for the DC-input power supply matches lead color coding used at the
DC power source.
• For DC input power cables, select the appropriate wire gauge based on the National Electrical
Code (NEC) and local codes for 40-amp service at nominal DC input voltage (–48/–60 VDC).
Three pairs of cable leads, source DC (–) and source DC return (+), are required for each power
distribution unit (PDU). These cables are available from any commercial cable vendor. All input
power cables for the chassis should have the same wire gauge and cable lengths should match within
10 percent of deviation.
Each DC input power cable is terminated at the PDU by a cable lug. The cable lugs must be
dual-hole, and have a straight tongue. They must be able to fit over 1/4-inch terminal studs at
0.625-inch (15.88-mm) centers.
OL-13208-03 4-23

Note DC input power cables must be connected to the PDU terminal studs in the proper positive
(+) and negative (–) polarity. In some cases, the DC cable leads are labeled, which is a
relatively safe indication of the polarity. However, you must verify the polarity by measuring
the voltage between the DC cable leads. When making the measurement, the positive (+)
lead and the negative (–) lead must always match the (+) and (–) labels on the power
distribution unit.
• An earth ground cable is required for each DC PDU. We recommend that you use at least 6-AWG
multistrand copper wire. This wire is not available from Cisco Systems; it is available from any
commercial cable vendor.
The ground wire cable lug should be dual-hole (as shown in Figure 4-15) and able to fit over M6
terminal studs at 0.625 inch (15.88mm) centers. Recommended lug terminal wire size Panduit part
number:
– LCD8-14A-L for 8AWG wire size
Figure 4-15 DC Input Power Cable Lug
All measurements in inches

2.24
End View
0.48 Ø 0.267
2 holes
Crimp area
25527
0.25 0.63 0.37
0.08
Note To avoid hazardous conditions, all components in the area where DC input power is
accessible must be properly insulated. Therefore, before installing the DC cable lugs, be sure
to insulate the lugs according to the manufacturer’s instructions.
Statement 1046
4-24 OL-13208-03

To connect the DC power supply, follow these steps:
Step 1 Make certain that the chassis grounding is connected before you begin installing the DC power supply.
Step 2 Locate the stud on the DC power supply for the GND connection which must be connected first and
follow these steps:
a. Using the grounding lug, replace the washers and Kepnut screw in the following order.
– Flat washer
– Grounding cable lug
– Kepnut screw
b. Tighten the Kepnut screws on the power supply studs.
9 10
OUTPUT INPUT INPUT

FAIL OK OK
OFF
55
ALARMS
60V
-48/-60V 40A
1A MAX
280023
6 5 4 3 2 1
1 Fans 6 DC Power supply earth ground lugs

2 DB-25 alarm connector 7 DC Power supply captive screws
3 Tie-wrap tabs 8 DC Power supply handle
4 DC power supply terminal and plastic cover 9 DC power supply On (|) /Off (O) switch
5 Earth grounding symbol 10 DC power supply LEDs
Step 3 Attach the other end of the cable to the site’s ground connection.
Step 4 Remove the plastic cover from the terminal block.
Caution Before you continue to install the terminal block ground wires, stop and perform Step 5. To prevent any
contact with metal lead on the ground wire and the plastic cover.
Step 5 You must wrap the positive and negative lead cables with sleeving. Take each lead wire and cover the
area from the lug to the wire with heavy shrink sleeving (see Figure 4-17).
OL-13208-03 4-25

Figure 4-17 DC Power Supply Terminal Block Ground Cable Lugs
1 2
OFF
-48/-60V 40A
This unit might have more than one power supply connection. All connections must be removed to de-energ
4
3
280024
1 Negative lug and wire with sleeving wrapped 3 Location of sleeving wrapped around the wire
around the wire and end of lug and end of the grounding stud
2 Positive lug and wire with sleeving wrapped 4 Earth ground lug and wire
around the wire and end of lug
Step 6 For easier cable-management, insert the negative lead cable first. Replace the ground lug with cable in
the following order:
a. Flat Washer
b. Ground lug with negative wire
c. Kepnut screw
Step 7 Tighten the Kepnut screw to recommended torque of 18 in-lbs minimum to 22 in-lbs maximum for the
positive stud and wire.
Note Secure the wires coming in from the terminal block so that they cannot be disturbed by casual contact.
Step 8 Use tie wraps to secure the wires, so that the wires are not pulled from the terminal block by casual
contact. Ti-wrap studs are located below the power supply terminal block (see Figure 4-18).
Step 9 Replace the terminal block plastic cover and tighten the screw. The plastic cover is slotted and keyed to
fit correctly over the terminal block.
4-26 OL-13208-03

Connecting a Terminal to the Cisco ASR 1000 Series RP1 Console Port
Figure 4-18 Cisco ASR 1006 Router DC Power Supply Terminal Block Plastic Cover
1 2
OFF
55
-48/-60V
40A
This unit
might have m
ore than on
e power su
pply conn
280027
ection. Al
l connectio
ns must be
remov
4
3
1 Negative lead 3 Plastic cover slotted area

2 Positive lead 4 Terminal block plastic cover
Step 10 Remove the tape from the circuit-breaker switch handle and move the circuit-breaker handle to the
on position.
Step 11 Switch the circuit breaker switch to the On (|) position.
This completes the procedure for connecting the DC power supply in the Cisco ASR 1006 Router.
Connecting a Terminal to the Cisco ASR 1000 Series RP1

Console Port
The Cisco ASR 1006 router processor has an asynchronous serial (EIA/TIA-232) RJ-45 console port
labeled CON on its front panel. You can connect this port to most types of video terminals through use
of the console cable kit that is included with your Cisco ASR 1006 Router. The console cable kit
contains:
• One RJ-45 to RJ-45 crossover cable
• One RJ-45 to DB-25 (female) adapter
OL-13208-03 4-27

Connecting a Terminal to the Cisco ASR 1000 Series RP1 Console Port
A crossover cable reverses pin connections from one end to the other. In other words, it connects pin 1
(at one end) to pin 8 (at the other end), pin 2 to pin 7, pin 3 to pin 6, and so on. You can identify a
crossover cable by comparing the two modular ends of the cable. Hold the cable ends in your hand,
side-by-side, with the tabs at the back. Ensure that the wire connected to the outside (left) pin of the left
plug (pin 1) is the same color as the wire connected to the outside (right) pin of the right plug (pin 8).
Use the following procedure to connect a video terminal to the console port on a route processor.
Note Each Cisco ASR 1000 Series Route Processor 1 must have a console port connection (typically to a
terminal server) if you are running a redundant configuration in the chassis.
Figure 4-19 Console Port and Auxiliary Port Connection on the ASR 1000 Series RP1
1 2
280094
AUX
LINK CON
NET
CARRIER MGMT ETHER
BITS
AUX
LINK CON
NET
CARRIER MGMT ETHER
BITS
Step 1 Connect one end of the RJ-45 cables to the serial RJ-45 port (CON) on the Cisco ASR 1000 Series Route
Processor 1 (Figure 4-19).
Step 2 Run the cable up and through the cable-management bracket and connect the other end of the RJ-45
cable to the RJ-45 adapter (Figure 4-20).
4-28 OL-13208-03

Connecting System Cables
Figure 4-20 Cable-Management Bracket with Cabling in the Cisco ASR 1006 Router
US
C/
AT
A
ST
A/L
C/
A
A/L
C/
POS
SPA-4XOC3-
A/L
C/
3
A/L
US
C/
AT
1
ST
A/L
C/
0
A/L
A
US
C/
POS
C/
SPA-4XOC3-
AT
A/L
A
ST
C/
A/L
C/
3
A/L
A
A/L
C/
POS
2
SPA-4XOC3-
A/L
C/
1
3
A/L
0
2
US
C/
AT
US
C/
1
ST
AT
A/L
C/
ST
A/L
C/
0
A/L
C/
POS
SPA-4XOC3-
A/L
C/
POS
A
SPA-4XOC3-
A/L
C/
A/L
C/
3
A/L
A/L
US
C/
1
AT
1
ST
A/L
C/
0
A/L
A
US
C/
POS
C/
SPA-4XOC3-
AT
A/L
A
ST
C/
A/L
C/
3
A/L
A
A/L
C/
POS
2
SPA-4XOC3-
A/L
C/
1
3
A/L
US
2
US
C/
C/
AT
AT
A
1
ST
A
ST
A/L
A/L
C/
C/
A
0
A/L
A/L
C/
C/
POS POS
SPA-4XOC3- SPA-4XOC3-
A
A
A/L
A/L
C/
C/
3
3
A/L
A/L
US
2
C/
AT
1
A
1
ST
A/L
C/
0
A
0
A/L
A
US
C/
POS
C/
SPA-4XOC3-
AT
A/L
A
ST
C/
A/L
C/
3
A/L
A
A/L
C/
POS
2
SPA-4XOC3-
A/L
C/
1
3
A/L
0
2
US
C/
AT
1
ST
A/L
C/
0
A/L
C/
POS
SPA-4XOC3-
A/L
C/
3
A/L
2
1
0
280086
4 3 2 1
1 AUXiliary connection 3 BITS port

2 MGMT Ethernet port 4 Cable-management U feature device
Step 3 Connect the adapter to your video terminal to complete the cable connection.
Step 4 Power on your video terminal.
Step 5 Configure your video terminal to match the following default console port settings: 9600 baud, 8 data
bits, No parity generation or checking, 1 stop bit, and No flow control.
Step 6 Go to the “Connecting System Cables” section on page 4-29 to continue the installation.
Connecting System Cables

Keep the following guidelines in mind when connecting external cables to the Cisco ASR 1006 Router:
• To reduce the chance of interference, avoid crossing high-power lines with any interface cables.
• Verify all cabling limitations (particularly distance) before powering on the system.
OL-13208-03 4-29

Auxiliary Connection
This asynchronous EIA/TIA-232 serial port (AUX) is used to connect a modem to the Cisco ASR 1000
Series Route Processor 1 for remote administrative access. Use the following procedure to connect the
Cisco ASR 1006 Router to a modem.
Step 1 Connect one end of the modem cable to the RJ-45 port on the primary Cisco ASR 1000 Series Route
Processor 1, labeled AUX.
Figure 4-21 Cisco ASR 1000 Series RP1 Port Connectors and LEDs
1 2 3 4 5 6
CARRIER LINK
BITS MGMT ETHERNET CON AUX
280079
1 AUX port 4 LINK LED
2 CON port 5 BITS port
3 MGMT Ethernet port 6 CARRIER LED
Step 2 Run the cable up and through the cable-management bracket U feature device as shown in Figure 4-20
and connect the other end of the cable to your modem.
If you have completed all cable connections, go to, Chapter 7, “Cisco ASR 1000 Series Routers Power
Up and Initial Configuration.”
4-30 OL-13208-03

C H A P T E R 5
This chapter describes the Cisco ASR 1004 Router and the procedures for installing the Cisco ASR 1004
Router on an equipment shelf or tabletop or in equipment racks. It also describes how to connect
interface and power cables.
• Connecting a Terminal to the Cisco ASR Series 1000 RP1 Console Port, page 5-29
• Connecting Network Management and Signal System Cables, page 5-30
Statement 1071

The Cisco ASR 1004 Router system consists of the following system level components:
• Two Cisco ASR 1000 Series SPA Interface Processor (SIP)
• One Cisco ASR 1000 Series Embedded Services Processor (Cisco ASR 1000-ESP10 or Cisco
ASR 1000-ESP20)
OL-13208-03 5-1

• One Cisco ASR 1000 Series Route Processor 1 (RP1)

• Dual (redundant) AC and DC power supplies
Front View
Figure 5-1 Cisco ASR 1004 Router —Front and Side View
6 7
5 8
US
A
C/
AT
ST
A
A/L
C/
A
A/L
C/
SPA-4XOC3-POS
A/L
C/
3
A/L
US
A
C/
AT
1
ST
A
A/L
C/
0
A
US
A/L
A
C/
C/
SPA-4XOC3-POS
AT
A
ST
A/L
A
C/
A/L
C/
3
A/L
A
A/L
C/
SPA-4XOC3-POS
2
A
A/L
C/
1
3
A/L
US
A
2
US
A
C/
C/
AT
AT
ST
A
1
ST
A
A/L
A/L
C/
C/
A
0
A/L
A/L
C/
C/
4
A
A
A/L
A/L
C/
C/
3
3
A/L
A/L
US
A
2
C/
AT
1
ST
A
1
A/L
C/
0
A
0
US
A/L
A
C/
C/
SPA-4XOC3-POS
AT
A
ST
A/L
A
C/
A/L
C/
3
A/L
A
A/L
C/
SPA-4XOC3-POS
2
A
A/L
C/
1
3
A/L
0
2
US
A
C/
AT
1
ST
A
A/L
C/
0
A/L
C/
SPA-4XOC3-POS
3
A
A/L
C/
3
A/L
2
1
0
2 HD CARRIER
BITS
LINK
MGMT ETHERNE
T
CON
AUX
USB
CRIT
280312
DF
ACTV MAJ
O
AC
PWR DISK
1
1
STBY MIN 0
STAT
P1
ASR1000-R
1 Slot RP0 with ASR 1000 Series RP1 5 SPA subslot 2

2 Slot FP0 with a Cisco ASR1000-ESP10 or 6 SPA subslot 0
Cisco ASR1000-ESP20
5-2 OL-13208-03

Rear View
Figure 5-2 shows the rear of the Cisco ASR 1004 Router with two AC power supplies installed.
Figure 5-2 Cisco ASR 1004 Router Rear View With AC Power Supply
1 2
OUTPUT INPUT FAN

FAIL OK OK
100V-240V~ 12A-5A
ALARMS
50-60Hz
60V
1A MAX
OUTPUT INPUT FAN

FAIL OK OK
100V-240V~ 12A-5A
ALARMS
50-60Hz
60V
1A MAX
280184
6 5 4 3
1 AC power supply Standby switch 4 AC power supply fan

3 AC power supply DB-25 alarm connector 6 AC power supply handle
OL-13208-03 5-3

Figure 5-3 shows the rear of the Cisco ASR 1004 Router with two DC power supplies installed.
Figure 5-3 Cisco ASR 1004 Router Rear View With DC Power Supplies
1 2
OUTPUT INPUT FAN

FAIL OK OK
60V
1A MAX
OUTPUT INPUT FAN

FAIL OK OK
60V
1A MAX
280185
7 6 5 4 3
1 DC power supply terminal block 5 Earth grounding symbol

2 DC power supply LEDs 6 DC power supply On/Off switch
3 DC power supply DB-25 alarm connector 7 DC power supply handle
operating temperature. (See Figure 5-2.) The fans are located at the rear of the chassis. A two-hole
grounding lug is located on the side of the chassis. Two power supplies, either two AC power supplies
or two DC power supplies, are accessed from the rear of the router.
Note Do not combine AC and DC power supplies in the same chassis.
Statement 1071
5-4 OL-13208-03

mount the chassis:
• On an equipment shelf or tabletop
• In a19-inch wide (standard), 4-post equipment rack or two-post, using the rack-mount brackets in
the accessory kit
chassis to make the chassis lighter for your rack installation.

• The Cisco ASR 1004 Router requires a minimum of 4 rack units (7 inches or 17.8 cm) of vertical
rack space. Measure the proposed rack location before mounting the chassis in the rack.
• Maintain a minimum clearance of 3 inches (7.62 cm) on the front, top, and sides of the chassis for
the cooling air inlet and exhaust ports, respectively. Avoid placing the chassis in an overly congested
rack or directly next to another equipment rack; otherwise, the heated exhaust air from other
equipment can enter the inlet air vents and cause an overtemperature condition inside the router.
OL-13208-03 5-5

conditions in the “Site Environmental Requirements” section on page 3-8.

Depth 22.50 in. (57.15 cm)
supply handles).
Height 6.95 in. (17.653cm) (4 rack-mount per EIA RS-310)
Width 17.25 in. (43.815 cm) (19 inch rack- mount or optional 23
Telco rack mount)
Weight 50 pounds (fully configured)
22.6796 kg

or tabletop.
5-6 OL-13208-03

• Always follow proper lifting practices as outlined in the “Electrical Safety” section on page 3-18,
when handling the chassis.

FANS
FAN
OK MULTI-
FAILURE
FAN
FAILURE
When hot CAUTION

removal swapping
this fan
shutdown minutes
will occur. or
1
2
3
4
0A
CISCO PROC 0B
ESSOR
10000 CISCO ONLY 5
10000 CISCO
6
FAIL
10000 CISCO
7
FAIL
10000 CISCO
8
FAIL
10000 CISCO
FAIL
10000
CISCO
10000 CISCO
10000 CISCO
FAIL
10000 CISCO
FAIL
CO
10000
FAIL
NS
OLE CO
FAIL
NS
CAR
OLE
ALA
AUX
CAR
RIER
LOO
RM
ALA
RIER
LOO
P
AUX
RM
0
P
0 ACT
IVIT
CAR
ETH Y ACT
ALA
CAR
IVIT
RIER
ER
LOO
SLO
ALA
LIN
RM
NE ETH
SLO
Y
RIER
CAR
LOO
K T
P
RM
1 ER
T
ALA
0
T
SLO
RIER
LIN
0
NE
LOO
SLO
1
1 0
RM
K T
T
P
T
0
0
1
2 1
2 1
POWER 1
FAULT
MISWIR 3
E 2
3 2
LINK
CAR
TX
ALA
RX
2
RIER
LOO
RM
4 3
4 3
3
5
CAR
4
5 4
RIER
TX
4
RX
5
5
5
GIGABIT ETHERNET

CH OC-12-DSO SM-IR
AC
O
AC
CR O
6XCT3–DS0
ITIC
CR
6XCT3–DS0
MA AL
ITIC
JO
R MA AL
MIN
JO
OR
POWER MIN
R
OR
6XCT3–DS0
FAULT
6XCT3–DS0
MISWIR
6XCT3–DS0
STA
TU
FAI S STA
L TU
FAI S
L
PROC
ESSOR
ONLY
30007
Note The chassis in Figure 5-4 does not represent the Cisco ASR 1004 Router. This is only an example of how
to lift a Cisco chassis.
OL-13208-03 5-7

Step 4 Repeat Step 2 through Step 3 on the other side of the chassis. Use all the screws to secure the rack-mount
attached cable-management brackets on the front of the Cisco ASR 1004 Router.
when you attach it to the chassis after the chassis is installed in a rack.
US
C/
AT
A
ST
A/L
C/
A
A/L
C/
-POS
SPA-4XOC3
A/L
C/
3
A/L
US
C/
AT
1
ST
A/L
C/
0
A/L
A
US
C/
-POS
C/
AT SPA-4XOC3
A/L
A
ST
C/
A/L
C/
3
A/L
A
A/L
C/
-POS
2
SPA-4XOC3
A
A/L
C/
1
3
A/L
A
2
US
A
US
C/
C/
AT
AT
A
1
ST
A
ST
A/L
A/L
C/
C/
A
0
A/L
A/L
C/
C/
-POS -POS
SPA-4XOC3 SPA-4XOC3
A
A
A/L
A/L
C/
C/
3
3
A/L
A/L
A
2
US
C/
AT
1
A
1
ST
A/L
C/
0
A
0
A/L
A
US
C/
-POS
C/
SPA-4XOC3
AT
A/L
A
ST
C/
A/L
C/
3
A/L
A
A/L
C/
-POS
2
SPA-4XOC3
A
A/L
C/
1
3
A/L
0
2
US
C/
AT
1
ST
A/L
C/
0
A/L
C/
-POS
SPA-4XOC3
A
A/L
C/
3
A/L
280176
1
0
2
AUX
LINK CON
NET
BITS
USB
CRIT
DF
ACTV MAJ
O
AC
PWR DISK
1
STBY MIN 0
STAT
ASR1000-RP1
1 Cable-management bracket screws 3 Chassis front rack-mount bracket ear

You have completed a tabletop or equipment shelf chassis installation. Go to the “Attaching a Chassis
Ground Connection” section on page 5-16 to continue the installation
5-8 OL-13208-03


The Cisco ASR 1004 Router can be installed with both front or rear rack-mount brackets.
Note The chassis rack-mounting flanges are secured directly to the chassis before you lift it into the rack.

equipment rack.
Mounting flanges
Minimum usable
(45.0 cm)
28014
Hole centerline
to hole centerline
(46.5 cm ± 0.15 cm)
OL-13208-03 5-9



Figure 5-7 shows where to attach the front rack-mount brackets to the Cisco ASR 1004 Router.
2 4
280174
1 Front rack-mount bracket 3 Chassis side vent holes

2 Front rack-mount bracket screws 4 Front rack-mount bracket and ear holes
Step 2 Position the front rack-mount bracket top hole with the chassis first top hole behind the side vent holes.
5-10 OL-13208-03

Step 5 Install the chassis in a rack. To install the Cisco ASR 1004 Router in a rack, go to Installing the Cisco

Step 1 Locate the threaded holes on the rear side of the chassis. Make certain that you hold the rear t rack-mount
bracket with the ear and holes facing outward and towards the rear of the chassis (see Figure 5-8).
1 2
3
0
280175
1 Rear rack-mount bracket ear and holes 3 Rear rack-mount bracket components that
slide into rear bracket that is attached to the
chassis
2 Rear rack-mount bracket (first bracket to 4 Rear rack-mount bracket screws
attach to chassis)
Step 2 Position the rear rack-mount bracket top hole with the chassis second top hole from the back (See
Figure 5-8).
Step 3 Insert and tighten the five screws on one side.
OL-13208-03 5-11

Step 4 After the bracket is secured to the side of the chassis, slide the two remaining components into the side
rack-mount bracket.
Step 5 Repeat Step 1 through Step 3 on the other side of the chassis. Use five screws to secure the rear
Caution Before you mount the ASR 1004 Router in a rack, make certain you read which rack-mount bracket ear
holes to use when positioning the chassis in the rack. As a result of using the designated ear holes on the
rack-mount bracket, the cable-management bracket installation will be made easier. For
cable-management installation instructions, go to Attaching a Chassis Ground Connection, page 5-16.

your safety:
5-12 OL-13208-03

Step 7 Hold the chassis in position against the mounting rails and follow these steps:
a. The Cisco ASR 1004 rack-mount ears contain 8 ear holes. Insert the bottom screw into the third hole
up from the bottom of the rack mount ear and use a hand-held screwdriver to tighten the screw to
the rack rail.
Note In the next step, insert the top screw diagonally from the bottom screw that you just
attached.This helps with keeping the chassis in place.
b. Insert the top screw into the third hole down from the top of the rack mount ear and tighten the screw
to the rack rail.
c. Insert a screw in the middle of the rack-mount bracket on both sides of the chassis.
d. Repeat these steps for the other side of the chassis.
Note As a result of using the specified rack-mount bracket ear holes, the cable-management bracket
can be easily attached to the rack-mount bracket when the chassis is in the rack.
You can install your Cisco ASR1004 chassis in a two-post rack or a four-post rack. See the “Two-Post
Rack Installation” section on page 5-13 and the four-post rack installation, go to the “Four-Post Rack
Installation” section on page 5-14.

front to back.
Figure 5-9 shows where to attach the chassis rack-mount brackets to the equipment rack.
OL-13208-03 5-13

US
C/A
AT
C/A
ST
A/L
C/A
A/L
SPA-4XOC3-POS
C/A
A/L
3
A/L
US
C/A
AT
1
C/A
ST
A/L
0
C/A
US
A/L
C/A
SPA-4XOC3-POS
AT
C/A
A/L
C/A
ST
A/L
3
A/L
C/A
A/L
SPA-4XOC3-POS
2
C/A
A/L
1
3
A/L
US
C/A
2
US
C/A
AT
AT
C/A
ST
1
C/A
ST
A/L
A/L
C/A
0
C/A
A/L
A/L
C/A
C/A
A/L
A/L
3
3
A/L
A/L
US
C/A
2
AT
1
C/A
ST
1
A/L
0
C/A
0
US
A/L
C/A
SPA-4XOC3-POS
AT
C/A
A/L
C/A
ST
A/L
3
A/L
C/A
A/L
SPA-4XOC3-POS
2
C/A
A/L
1
3
A/L
0
2
US
C/A
AT
1
C/A
ST
A/L
0
C/A
A/L
SPA-4XOC3-POS
C/A
A/L
3
A/L
2
1
0
AUX
LINK CON
T
HD CARRIER MGMT ETHERNE
BITS
USB
CRIT
DF
ACTV MAJ
O
AC
PWR DISK
1
STBY MIN 0
STAT
1
ASR1000-RP
280178
1
2
1 Rack-mount bracket ear and holes 2 Rack equipment rail

3-20.
5-14 OL-13208-03

front to back.
to support the chassis.Using two people, lift the chassis into the rack using the side handles and grasping
Note Use the third hole up from the bottom of the rack-mount bracket and the third hole down from the top
of the rack-mount bracket.
to the rack rails on each side of the chassis. Figure 5-10 shows the rear rack-mount brackets and the front
rack-mount brackets on the Cisco ASR 1004 Router.
Step 4 Finger-tighten 4 more screws to the rack rails on each side of the chassis.
OL-13208-03 5-15

Figure 5-10 Cisco ASR 1004 Router in a Four Post Rack - Front and Rear Rack-Mounting
US
C/A
AT
C/A
ST
A/L
C/A
A/L
SPA-4XOC3-POS
C/A
A/L
3
A/L
US
C/A
AT
1
C/A
ST
A/L
0
C/A
US
A/L
C/A
SPA-4XOC3-POS
AT
C/A
A/L
C/A
ST
A/L
3
A/L
C/A
A/L
SPA-4XOC3-POS
2
C/A
A/L
1
3
A/L
US
C/A
2
US
C/A
AT
AT
C/A
ST
1
C/A
ST
A/L
A/L
2
C/A
0
C/A
A/L
A/L
C/A
C/A
A/L
A/L
3
3
A/L
A/L
US
C/A
2
AT
1
C/A
ST
1
A/L
0
C/A
0
US
A/L
C/A
SPA-4XOC3-POS
AT
C/A
A/L
C/A
ST
A/L
3
A/L
C/A
A/L
SPA-4XOC3-POS
2
C/A
A/L
1
3
A/L
0
2
US
C/A
AT
1
C/A
ST
A/L
0
C/A
A/L
SPA-4XOC3-POS
C/A
A/L
3
A/L
2
1
0
AUX
LINK CON
T
BITS
USB
CRIT
DF
ACTV MAJ
O
AC
PWR DISK
1
STBY MIN 0
STAT
1
ASR1000-RP
280177
3
4
1 Equipment rack rear rail 3 Front rack-mount bracket ear and holes
2 Chassis rear rack-mount bracket and ear holes 4 Equipment rack front rail
This completes the procedure for installing the chassis in the rack. Proceed to the “Attaching a Chassis
Ground Connection” section on page 5-16 to continue the installation.

Connecting the Cisco ASR 1004 Router chassis to earth ground is required for all DC powered
installations and any AC powered installation where compliance with Telcordia grounding requirements
is necessary.
Caution The dual-lug chassis ground stud must be installed, the SIP and SPA must be fully inserted and screwed
in and earthed to prevent a potential hazard in a telecom line.
5-16 OL-13208-03

(earth) connection for the chassis. A chassis ground connector is provided on each Cisco ASR 1004
Router. (See Figure 5-11 on page 5-17.) There is a grounding stud on the side of the chassis and on the
DC power supply (primary grounding stud).
disconnected.
Recommended Tools and Supplies

• Dual-lug chassis ground component
• Grounding wire
Figure 5-11 shows the location of the dual ground lug on the rear of the of Cisco ASR 1004 Router.
Figure 5-11 Chassis Ground Lug Location on the Cisco ASR 1004 Router
US
C/A
AT
C/A
ST
A/L
C/A
A/L
SPA-4XOC3-POS
C/A
A/L
3
A/L
US
C/A
AT
1
C/A
ST
A/L
0
C/A
US
A/L
C/A
SPA-4XOC3-POS
AT
C/A
A/L
C/A
ST
A/L
3
A/L
C/A
A/L
SPA-4XOC3-POS
2
C/A
A/L
1
3
A/L
US
C/A
2
US
C/A
AT
AT
C/A
ST
1
C/A
ST
A/L
A/L
C/A
0
C/A
A/L
A/L
C/A
C/A
A/L
A/L
3
3
A/L
A/L
US
C/A
2
AT
1
C/A
ST
1
A/L
0
C/A
0
US
A/L
C/A
SPA-4XOC3-POS
AT
C/A
A/L
C/A
ST
A/L
3
A/L
C/A
A/L
SPA-4XOC3-POS
2
C/A
A/L
1
3
A/L
0
2
US
C/A
AT
1
C/A
ST
A/L
0
C/A
A/L
SPA-4XOC3-POS
280179
C/A
A/L
3
A/L
2
1
0
AUX
LINK CON
T
BITS
USB
CRIT
DF
ACTV MAJ
O
AC
PWR DISK
1
STBY MIN 0
1
STAT
1
ASR1000-RP
1 Chassis ground connector on the Cisco ASR 1004 Router
Use the following procedure to attach the grounding lug to the chassis ground connector on your chassis:
Step 2 Insert the AWG #6 wire into the wire receptacle on the grounding lug.
Step 3 Use the crimping tool to carefully crimp the wire receptacle around the wire; this step is required to
ensure a proper mechanical connection.
OL-13208-03 5-17

Step 4 Attach the grounding lug with the wire on the left to avoid having the grounding wire overlapping the
power supply. Figure 5-12 shows how to attach the grounding screws.
280180
1 Chassis ground connector 2 Ground symbol
Step 6 Insert the two screws through the holes in the grounding lug as shown in Figure 5-12.
This completes the procedure for attaching a chassis ground connection. To continue on, go to Attaching
the Cable-Management Bracket, page 5-19.
5-18 OL-13208-03


The cable-management brackets for the Cisco ASR 1004 Router contain three independent
slots. For Cisco ASR 1000 SIPs, these brackets work in tandem with shared port adapter product feature
cable-management device to allow installation and removal of adjacent cards without the need to remove
cables.
to the chassis.
in the equipment rack:
Figure 5-13 shows where to attach the cable-management brackets to the Cisco ASR 1004 Router in a
rack.
OL-13208-03 5-19

Figure 5-13 Chassis Rack-Mount Bracket Ear Holes for the Cable-Management Bracket
US
C/
AT
A
ST
A/L
C/
A
A/L
C/
-POS
SPA-4XOC3
A/L
C/
3
A/L
US
C/
AT
1
ST
A/L
C/
0
A/L
A
US
C/
-POS
C/
SPA-4XOC3
AT
A/L
A
ST
C/
A/L
C/
3
A/L
A
A/L
C/
-POS
2
SPA-4XOC3
A/L
C/
1
3
A/L
A
2
US
A
US
C/
C/
AT
AT
A
1
ST
A
ST
A/L
A/L
C/
C/
A
0
A/L
A/L
C/
C/
-POS -POS
SPA-4XOC3 SPA-4XOC3
A
A
A/L
A/L
C/
C/
3
3
3
A/L
A/L
A
2
US
C/
AT
1
A
1
ST
A/L
C/
0
A
0
A/L
A
US
C/
-POS
C/
SPA-4XOC3
AT
A/L
A
ST
C/
A/L
C/
3
A/L
A
A/L
C/
-POS
2
SPA-4XOC3
A/L
C/
1
3
A/L
0
2
US
C/
AT
1
ST
A/L
C/
0
A/L
C/
-POS
SPA-4XOC3
A/L
C/
3
A/L
280176
1
0
2
AUX
LINK CON
NET
BITS
USB
CRIT
DF
ACTV MAJ AC
O DISK
PWR 1
STBY MIN 0
STAT
ASR1000-RP1
1 Cable-management bracket top and bottom 3 Chassis rack-mount bracket

screw
2 Cable-management bracket and U feature
device
This completes the procedure for installing the cable-management brackets on the chassis in a rack.

5-20 OL-13208-03


The Cisco ASR 1004 Router has a DCE-mode console port for connecting a console terminal and a
DTE-mode auxiliary port for connecting a modem or other DCE device (such as another router) to your
chassis. Figure 5-14 shows the CON and AUX ports on the Cisco ASR 1000 Series RP1 route processor
card.
.
Figure 5-14 Cisco ASR 1000 Series RP1—CON and AUX Ports
1 2
A
0
A/L
A
US
C/
-POS
C/
SPA-4XOC3
AT
A/L
A
ST
C/
A/L
C/
3
A/L
A
A/L
C/
-POS
2
SPA-4XOC3
A/L
C/
1
3
A/L
0
2
US
C/
AT
1
ST
A/L
C/
0
A/L
C/
-POS
SPA-4XOC3
A/L
C/
3
A/L
2
1
0
280181
AUX
LINK CON
NET
BITS
USB
CRIT
DF
ACTV MAJ
O
AC
PWR DISK
1
STBY MIN 0
STAT
ASR1000-RP1
1 Console port - CON 2 Auxiliary port - AUX
Note Both the console and the auxiliary ports are asynchronous serial ports; any devices connected to these
device; for example, most modems are asynchronous devices.)
The Cisco ASR 1004 Router uses RJ-45 ports for both the auxiliary port and the console port.
For console and auxiliary port pinouts for the RJ-45 connector, see Cisco ASR 1004 Router
Specifications, page A-5. Both ports are configured as asynchronous serial ports.
Connecting the Ethernet Management Port Cable

When using the Fast Ethernet Management port in the default mode (speed-auto and duplex-auto) the
port operates in auto-MDI/MDI-X mode. The port automatically provides the correct signal connectivity
through the Auto-MDI/MDI-X feature. The port automatically senses a crossover or straight-through
cable and adapts to it.
However, when the Fast Ethernet Management port is configured to a fixed speed (10/100/1000 Mbps)
through command-line interface (CLI) commands, the port is forced to MDI mode.
When in a fixed-speed configuration and MDI mode:
OL-13208-03 5-21

• Use a crossover cable to connect to an MDI port

• Use a straight-through cable to connect to an MDI-X port
Figure 5-15 Cisco ASR 1000 Series RP1 MGMT Ethernet Port Connector
US
C/
AT
A
ST
A/L
C/
A
A/L
S
C/
SPA-4XOC3-PO
A/L
C/
3
A/L
US
C/
AT
1
ST
A/L
C/
0
A/L
A
US
S
C/
C/
SPA-4XOC3-PO
AT
A/L
A
ST
C/
A/L
C/
3
A/L
A
A/L
S
C/
2
SPA-4XOC3-PO
A/L
C/
1
3
A/L
US
2
US
C/
C/
AT
AT
A
1
ST
A
ST
A/L
A/L
C/
C/
2
A
0
A/L
A/L
S
C/
S
C/
SPA-4XOC3-PO SPA-4XOC3-PO
A
A
A/L
A/L
C/
C/
3
3
A/L
A/L
US
2
C/
AT
1
A
1
ST
A/L
C/
0
A
0
A/L
A
US
S
C/
C/
SPA-4XOC3-PO
AT
A/L
A
ST
C/
A/L
C/
3
A/L
A
A/L
S
C/
2
SPA-4XOC3-PO
A/L
C/
1
3
A/L
0
2
US
C/
AT
1
ST
A/L
C/
0
A/L
S
C/
SPA-4XOC3-PO
A/L
C/
3
A/L
2
1
0
AUX
LINK CON
ET
HD CARRIER MGMT ETHERN
BITS
USB
CRIT
DF
ACTV MAJ
O
AC
PWR DISK
1
STBY MIN 0
STAT
P1
ASR1000-R
280183
1
1 MGMT Ethernet port 2 Cable-management bracket and U feature

device

Statement 1046
Statement 1003
Statement 1030
5-22 OL-13208-03

This section provides the procedures for connecting AC-input and DC-input power to your
Cisco ASR 1004 Router.
Cisco ASR 1000

Series Router DC
Cisco ASR 1004 24 30 40 10 8
Cisco ASR 1002 16 20 30 12 10
Note Detailed instructions for removing and replacing the Cisco ASR1000 Series AC and DC power supplies
are in Chapter 8, “Replacing Cisco ASR 1000 Series Routers Field-Replaceable Units.”.

Follow these steps to connect an AC-input power supply to the Cisco 1004 chassis:
Step 1 Insert an AC power supply in power supply slot 0 or power supply slot 1 until it is fully seated.
Step 2 Tighten the captive screws.
Step 3 Insert the AC power cable into the power inlet.
Step 4 Plug the power supply cable into the power source.
Note For additional AC power cable strain relief, secure the cable to the power supply handle by
inserting a nylon cable tie through the hole in the handle and around the cable.
OL-13208-03 5-23

1 2
OUTPUT INPUT FAN

FAIL OK OK
100V-240V~ 12A-5A
ALARMS
50-60Hz
60V
1A MAX
OUTPUT INPUT FAN

FAIL OK OK
100V-240V~ 12A-5A
ALARMS
50-60Hz
60V
1A MAX
280184
6 5 4 3

Step 5 Turn the power supply switch to On (|) position.
This completes the procedure for connecting AC-input power.

This section describes how to connect the DC power supply in the Cisco ASR 1004 Router.
5-24 OL-13208-03

1 2
OUTPUT INPUT FAN

FAIL OK OK
60V
1A MAX
OUTPUT INPUT FAN

FAIL OK OK
60V
1A MAX
280185
7 6 5 4 3
1 DC power supply terminal block and plastic 5 DC power supply earth ground symbol
cover
2 DC power supply LEDs 6 DC power supply On (I)/ Off (O)
Before you begin, read these important notices:

• The color coding of the DC-input power supply leads depends on the color coding of the DC power
source at your site. Typically, green or green/yellow is used for ground (GND), black is used for
-48V on negative (–) terminal and red is used for RTN on the positive (+) terminal. Make certain the
lead color coding you choose for the DC-input power supply matches lead color coding used at the
DC power source.
• For DC input power cables, select the appropriate wire gauge based on the National Electrical
Code (NEC) and local codes for 60-amp service at nominal DC input voltage (–48/–60 VDC).
Three pairs of cable leads, source DC (–) and source DC return (+), are required for each power
distribution unit (PDU). These cables are available from any commercial cable vendor. All input
power cables for the chassis should have the same wire gauge and cable lengths should match within
10 percent of deviation.
Each DC input power cable is terminated at the PDU by a cable lug. The cable lugs must be
dual-hole, and have a 45-degree angle tongue. They must be able to fit over #10 power terminal stud.
Note DC input power cables must be connected to the PDU terminal studs in the proper positive
(+) and negative (–) polarity. In some cases, the DC cable leads are labeled, which is a
relatively safe indication of the polarity. However, you must verify the polarity by measuring
the voltage between the DC cable leads. When making the measurement, the positive (+)
lead and the negative (–) lead must always match the (+) and (–) labels on the PDU.
OL-13208-03 5-25

• An earth ground cable is required for each DC PDU. We recommend that you use at least 6-AWG
multistrand copper wire. This wire is not available from Cisco Systems; it is available from any
commercial cable vendor.
The ground wire cable lug should be dual-hole (as shown in Figure 5-18) and able to fit over M6
terminal studs at 0.625-inch (15.88-mm) centers. Recommended lug terminal wire size Panduit part
number:
Figure 5-18 DC Input Power Cable Lug

2.24
End View
0.48 Ø 0.267
2 holes
Crimp area
25527
0.25 0.63 0.37
0.08
Note To avoid hazardous conditions, all components in the area where DC input power is
accessible must be properly insulated. Therefore, before installing the DC cable lugs, be sure
to insulate the lugs according to the manufacturer’s instructions.
Statement 1046
Statement 1046To connect the Cisco ASR 1004 Router DC power supply, follow these steps:
Step 1 Make certain that the chassis grounding is connected before you begin installing the DC power supply.
Step 2 Locate the terminal block and remove the plastic cover.
a. Unscrew and remove the two screws.
b. Slide the plastic cover off of the terminal block.
5-26 OL-13208-03

Step 3 On the DC power supply terminal block, locate the GND connection which must be connected first and
follow these steps:
a. Using the two-hole grounding lug, replace the washers and Kepnut screw in the following order.
– Flat washer
– Kepnut screw
b. Tighten the Kepnut screws (use the screwdriver to tighten the screw in the terminal block to a torque
of 8 in-lbs / 2 per.) on the power supply studs.
Figure 5-19 Cisco ASR 1004 Router DC Power Supply Grounding Wire and Stud

2.24
End View
0.48 Ø 0.267
2 holes
Crimp area
25527
0.25 0.63 0.37
0.08
Step 4 Attach the other end of the cable to the site ground connection.
Caution Before you continue to install the terminal block wires, stop and perform Step 5. To prevent any contact
with metal lead on the wire and the plastic cover.
Step 5 You must wrap the positive and negative cables with sleeving. Take each wire and cover the area from
the lug to the wire with heavy shrink sleeving.
OL-13208-03 5-27

Figure 5-20 Cisco ASR 1004 Router DC Power Supply Cable Connection
280187
5 4 3
1 Power supply stud and wire 4 Flat washer

2 Ground lug nut 5 Kepnut screw
3 Earth ground symbol
Step 6 For easier cable-management, insert the negative cable first. Replace the ground lug with cable in the
following order:
a. Flat Washer
b. Ground lug with negative wire
c. Kepnut screw
Step 7 Tighten the Kepnut screw (use the screwdriver to tighten the screw in the terminal block to a torque of
8 in-lbs / 4 per.) and repeat the same steps for the positive stud and wire.
contact. Ti-wrap studs are located below the supply terminal block.
Step 9 Replace the terminal block plastic cover, which slides over the terminal block; then tighten the screws
(tighten the screw to a torque of 5 in-lbs / 1 per.).
Step 10 Remove the tape from the circuit-breaker switch handle and move the circuit-breaker handle to the
on position, if you taped the circuit breaker.
5-28 OL-13208-03

Connecting a Terminal to the Cisco ASR Series 1000 RP1 Console Port
Step 11 Switch the On/Off circuit breaker switch to the On (|) position.
Connecting a Terminal to the Cisco ASR Series 1000 RP1

Console Port
The Cisco ASR 1004 router processor has an asynchronous serial (EIA/TIA-232) RJ-45 console port
labeled CON on its front panel. You can connect this port to most types of video terminals through use
of the console cable kit that is included with your Cisco ASR 1004 Router. The console cable kit
contains:
Figure 5-21 Cisco ASR 1004 Router ASR 1000 Series RP1 Console Port
1 2
A
0
A/L
A
US
C/
-POS
C/
SPA-4XOC3
AT
A/L
A
ST
C/
A/L
C/
3
A/L
A
A/L
C/
-POS
2
SPA-4XOC3
A
A/L
C/
1
3
A/L
0
2
US
C/
AT
1
ST
A/L
C/
0
A/L
C/
-POS
SPA-4XOC3
A
A/L
C/
3
A/L
2
1
0
280181
AUX
LINK CON
NET
BITS
USB
CRIT
DF
ACTV MAJ
O
AC
PWR DISK
1
STBY MIN 0
STAT
ASR1000-RP1
1 CON port connection 2 AUX port connection
Step 1 Connect one end of the RJ-45 cables to the serial RJ-45 port (CON) on the Cisco ASR 1000 Series Route
Processor 1 (Figure 5-21).
OL-13208-03 5-29

Connecting Network Management and Signal System Cables
Figure 5-22 Cisco ASR 1004 Router Cable-Management Bracket
US
C/
AT
A
ST
A/L
C/
A
A/L
S
C/
SPA-4XOC3-PO
A/L
C/
3
A/L
US
C/
AT
1
ST
A/L
C/
0
A/L
A
US
S
C/
C/
SPA-4XOC3-PO
AT
A/L
A
ST
C/
A/L
C/
3
A/L
A
A/L
S
C/
2
SPA-4XOC3-PO
A/L
C/
1
3
A/L
US
2
US
C/
C/
AT
AT
A
1
ST
A
ST
A/L
A/L
C/
C/
2
A
0
A/L
A/L
S
C/
S
C/
SPA-4XOC3-PO SPA-4XOC3-PO
A
A
A/L
A/L
C/
C/
3
3
A/L
A/L
US
2
C/
AT
1
A
1
ST
A/L
C/
0
A
0
A/L
A
US
S
C/
C/
SPA-4XOC3-PO
AT
A/L
A
ST
C/
A/L
C/
3
A/L
A
A/L
S
C/
2
SPA-4XOC3-PO
A/L
C/
1
3
A/L
0
2
US
C/
AT
1
ST
A/L
C/
0
A/L
S
C/
SPA-4XOC3-PO
A/L
C/
3
A/L
2
1
0 AUX
LINK CON
ET
HD CARRIER MGMT ETHERN
BITS
USB
CRIT
DF
ACTV MAJ
O
AC
PWR DISK
1
STBY MIN 0
STAT
P1
ASR1000-R
280183
1
1 BITS port connection 2 Cable-management bracket U feature device
Step 5 Configure your video terminal to match the following default console port settings:
• 9600 baud
• 8 data bits
• No parity generation or checking
• 1 stop bit
• No flow control
Step 6 Go to the “Connecting Network Management and Signal System Cables” section on page 5-30 to
continue the installation.
Connecting Network Management and Signal System Cables

The Cisco ASR 1004 Router has connections to both the internal Ethernet management network and the
external data network.
• The internal Ethernet management network connections are made through an Ethernet port on the
front panel of the Cisco ASR 1000 Series Route Processor 1.
• The external data network connections are made through front panel ports on several types of SPAs.
5-30 OL-13208-03

Processor 1, labeled AUX.
Figure 5-23 Cisco ASR 1000 Series RP1 Auxiliary Connector
1 2
A
0
A/L
A
US
C/
-POS
C/
SPA-4XOC3
AT
A/L
A
ST
C/
A/L
C/
3
A/L
A
A/L
C/
-POS
2
SPA-4XOC3
A/L
C/
1
3
A/L
0
2
US
C/
AT
1
ST
A/L
C/
0
A/L
C/
-POS
SPA-4XOC3
A/L
C/
3
A/L
2
1
0
280181
AUX
LINK CON
NET
BITS
USB
CRIT
DF
ACTV MAJ
O
AC
PWR DISK
1
STBY MIN 0
STAT
ASR1000-RP1
Step 2 Run the cable up and through the cable-management bracket and connect the other end of the cable to
your modem.
OL-13208-03 5-31

5-32 OL-13208-03

C H A P T E R 6
This chapter describes the Cisco ASR 1002 Router and provides procedures for installing the
Cisco ASR 1002 Router on an equipment shelf or tabletop or in an equipment rack.
• Two-Post Rack Installation, page 6-18

The Cisco ASR 1002 Router is part of the Cisco aggregation services family of routers. The Cisco
ASR 1002 Router offers a compact form factor router that satisfies customer demands such as low power
consumption and decreased usage of rack space.
The Cisco ASR 1002 Router supports three half-height SPAs and an optional built-in 4xGE SPA. The
Cisco ASR 1002 Router supports all the general-purpose routing and security features of the Cisco ASR
1000 Series Routers. It uses the same internal control and data-plane architecture as the other Cisco
ASR 1000 Series Routers.
The Cisco ASR 1002 Router supports:
• Cisco ASR1000-ESP5 or Cisco ASR1000-ESP10 as a field-replaceable unit (FRU)
• The Cisco Embedded Route Processor which supports 2MB upgradeable BootROM and 8GB eUSB
bulk storage.
• 1 + 1 redundant AC or DC power supplies.
• Stratum-3 network clocking per GR-1244-CORE, with T1/E1 BITS interface or SPAs as timing
sources.
OL-13208-03 6-1

• A built- in 4x1GE Interface providing four SFP based GE connections, designated as SPA bay 0.
Note The built-in Gigabit Ethernet ports on the Cisco ASR1002 Router support the same small
form-factor pluggable (SFP) optical transceivers as the 5x1 GE SPA. For specific shared port
adapter SFP compatibility listings, go to Chapter 1 in:
http://cisco.com/en/US/docs/interfaces_modules/shared_port_adapters/install_upgrade/ASR10
00/ASRspahw.pdf
(This does not include the Ethernet management port on the Cisco ASR1000-RP1.)
The Cisco ASR 1002 Router supports upgradeable Cisco ASR1000-ESP5 or ASR1000-ESP10 assembly
and the power supply modules as field-replaceable units. The Cisco embedded ASR1000-SIP10 and
Cisco embedded ASR1000-RP1 assemblies are fixed into the chassis and are not upgradeable; but the
shared port adapters in the SIP are field upgradable.
• Cisco ASR 1002 Router Components, page 6-4
Front View
Figure 6-1 shows the Cisco ASR 1002 Router with modules installed.
Figure 6-1 Cisco ASR 1002 Router —Front View
1 3
PWR ACTV
STAT STBY
ASR1000-ESP10
C/A
C/A
C/A
C/A
pwr min
US
AT
A/L
A/L
A/L
A/L
ST
stat maj
SPA-4XOC3-POS
crit
0
280369
C/A
C/A
C/A
C/A
C/A
C/A
C/A
C/A
US
US
AT
AT
A/L
A/L
A/L
A/L
A/L
A/L
A/L
A/L
ST
ST
0
2 4
1 Embedded ASR1000-RP1 in the subslot and 3 SPA subslot 1

represents the built in 4xGE SPA.
Note The SPAs in subslots 1-3 are field upgradeable. The SIP that the SPAs reside in is not field-upgradeable
and the Cisco ASR1000-RP1 is embedded in the chassis and not field upgradeable.
6-2 OL-13208-03

Rear View
Figure 6-2 shows the Cisco ASR 1002 Router AC power supply.
1 2 3 4 5 6


280288
1
8 7

Figure 6-3 shows the Cisco ASR 1002 Router with a DC power supply.
1 2 3 4 5 6


280289
1
-48V/-60V 16A -48V/-60V 16A
7
10 9 8

5 Power supply fan 10 Negative lead
OL-13208-03 6-3

operating temperature. The fans are located at the rear of the chassis. A two-hole grounding lug is located
on the side of the chassis. Two power supplies, either two AC power supplies or two DC power supplies
are accessed from the rear of the router.
Caution Use only AC power supplies or DC power supplies in the Cisco ASR 1002 Router. Do not mix power
supply types.
Cisco ASR 1002 Router Components

The Cisco ASR 1002 Router system is derived from the architecture of the other Cisco ASR 1000 Series
routers. The three main subassemblies of any Cisco ASR 1000 Series Routers are all supported in the
Cisco ASR 1002 Router, which is the:
• Cisco embedded ASR1000-RP1 and Cisco embedded ASR1000-SIP10 (not field upgradable)
• Cisco ASR1000-ESP5 and Cisco ASR1000-ESP10 embedded services processors are
field-replaceable units (FRU)
• AC or DC power supplies which are field-replaceable units
Cisco Embedded ASR1000-RP1 for Cisco ASR 1002 Router Description

The Cisco ASR 1000 Series route processor (embedded for the Cisco ASR 1002 Router) is the central
control processor and runs the network operating system.
The Cisco embedded ASR1000-RP1 supports management interfaces such as the Ethernet network
management port and console and auxiliary serial ports. It has LED status indicators, an RJ-45 plug for
a BITS timing reference and one USB port which can be used with smart cards for secure key distribution
or for image or configuration file updates.
The Cisco embedded ASR1000-RP1 deviates from the other ASR Series Route Processor 1 for the Cisco
ASR 1006 router and the Cisco ASR 1004 Router in the following ways:
• Bulk file storage is on a large eUSB device (to 8GB (bytes) supported) with no SATA hard-drive
supported.
• Redundant Cisco Router Processor 1 is not supported.
• Network clock changes. No second BITS clock input supported.
• A built-in 4xGE SPA is included. This shared port adapter provides 4 SFP-based GE connections.
Cisco Embedded ASR1000-SIP10 and SPAs for the Cisco ASR 1002 Router Description
The Cisco embedded ASR1000-SIP10 in the Cisco ASR 1002 Router is built into the Cisco ASR 1002
Router. The Cisco embedded ASR1000-SIP10 provides the physical and electrical termination for up to
three half-height SPAs or one full-height and one half-height SPA. Double-wide SPAs are not supported.
The fourth SPA slot is connected to the built-in 4xGE SPA that resides on the Cisco embedded
ASR1000-RP1.
The Cisco embedded ASR1000-SIP10 interface, like the Cisco ASR 1006 Router and Cisco ASR 1004
Router, supports all Cisco embedded ASR1000-SIP10 functions and services. However, the Cisco
embedded ASR1000-SIP10 differs in the following areas:
• Functions as the base board for Cisco embedded ASR1000-RP1
6-4 OL-13208-03

• Only supports three removable half-height SPAs on Bay 1, 2, and 3. The fourth SPA is a built-in
4xGE SPA on Bay 0, which is located on the Cisco embedded ASR1000-RP1.
• Is not a field-replaceable unit (FRU) and does not support online insertion and removal (OIR).
Note The shared port adapters (SPAs) on the Cisco embedded ASR1000-SIP10 in the Cisco
ASR 1002 Router do support online insertion and removal.
The Cisco ASR1002 Router embedded ASR1000-RP1 also provides the circuitry for the built-in 4xGE
SPA. Some configurations of the Cisco ASR1002 Router will not populate the built-in 4xGE SPA and
will have only three SPA bays available for interface cards.
Cisco ASR1000-ESP5 or ASR1000-ESP10 Description

The Cisco ASR 1002 Router supports the Cisco ASR1000-ESP5 or Cisco ASR1000-ESP10 embedded
services processors. The Cisco ASR 1002 does not support the Cisco ASR1000-ESP20.
Figure 6-4 shows the Cisco ASR1000-ESP10 faceplate.
Figure 6-4 Cisco ASR1000-ESP10 LEDs
1 2
PWR ACTV
STAT STBY
ASR1000-ESP10 280080
3 4
OL-13208-03 6-5

Table 6-1 lists the Cisco ASR1000-ESP5 or Cisco ASR1000-ESP10 LEDs and behaviors.
Table 6-1 Cisco ASR 1000-ESP5 or Cisco ASR1000-ESP10 LED Activity
No LED Label LED Color In the Power Up State -Behavior Description

1 PWR Power Solid green All power supplies are within operational limits.
2 ACTV Active Green The embedded services processor is green when
active.
3 STAT STATUS Green Code has successfully downloaded and is
operational.
Yellow BOOT ROM has successfully loaded.
Red Not booted.
4 STBY Standby None Will always be off.
Note The Cisco ASR 1000-ESP5 can only be used in the Cisco ASR 1002 Router.
Power Supplies in the Cisco ASR 1002 Router

The Cisco ASR 1002 Router power supply module consists of either an AC or DC input in a closed frame
power supply with two DC voltage outputs: +12V and 3.3V. The AC power supply operates between
85VAC to 264VAC and DC operates between –40.5 to –72VDC. The DC and AC power supply shall
current share on the 12V output and is used in a dual (redundant) hot pluggable system.
The power supplies are installed into the rear of the chassis and are hot pluggable. The Cisco ASR 1002
Router supports up to 588W input power from an infrastructure standpoint (cooling capacity, midplane
and power distribution) but initial power supply development limit is up to 470W output (AC and DC
Input).
AC Power Supply for Cisco ASR 1002 Router

The AC power supply input inlet is an IEC connector with AC switch and the current rating on the
connector and switch is 10 Amps. The AC power supply is secured into the chassis with two captive
screws mounted on the faceplate.
6-6 OL-13208-03

Table 6-2 Cisco ASR 1002 Router AC Power Supply LEDs

INPUT OK Power supply activity Green LED is green and signals that the AC power supply input
voltage is greater than 85V.
None If LED is not lighted, the AC input voltage is less than
70V or the power supply is turned off. For an AC input
voltage between 70V and 85V the INPUT OK LED can be
either on, off, or flashing
FAN OK Power supply fan activity Green The LED is illuminated green when all fans are
operational.
A bi-color LED indicates
fan status. Red The LED is illuminated red when a fan failure is detected.
OUTPUT FAIL Power supply activity Red LED is red. It is off to signal that the DC output voltages
are within the normal operating range. Output voltage
between the minimum and maximum limits will not
create an output fail alarm and output voltages below the
minimum or above the maximum will create an output fail
alarm.
Figure 6-5 shows the AC Power Supply for the Cisco ASR1002 Router.
Figure 6-5 AC Power Supply for the Cisco ASR 1002 Router
1 2 3 4 5 6


280288
1
8 7

4 AC power supply LEDs 8 AC power supply inlet
DC Power Supply for Cisco ASR 1002 Router

The DC power supply input connector is a euro-style terminal block and is compliant to all safety
agencies and electrical requirements of the supply. The DC power supply operates within specification
from –40.5VDC to –72VDC continuously once the power supply DC input turn on threshold of –43.5V
has been reached.
OL-13208-03 6-7

The DC power input connector euro-style terminal block will accept three wires: one positive polarity,
one negative polarity, and one earth ground wire. There is provisions on the front panel to wire tie and
strain relief the DC input wiring. The connection order shall be negative (–), positive (+), GND. The DC
power supply is secured into the system chassis with two captive screws mounted on the faceplate.
Figure 6-6 shows the DC Power Supply for the Cisco ASR1002 Router.
Figure 6-6 DC Power Supply for the Cisco ASR 1002 Router
1 2 3 4 5 6


280289
1
-48V/-60V 16A -48V/-60V 16A
7
10 9 8

6-8 OL-13208-03

The Cisco ASR 1002 Router DC power supply LEDs are defined inTable 6-3.

INPUT OK A bi-color LED indicates Green LED illuminates green to signal that the DC power supply
presence of input voltage input voltage is greater than 43.5VDC at turn-on and
remains green down to 39VDC.
Amber The LED illuminates amber if the power supply turns off
due to low input voltage (falls below 39VDC) and
indicates that there is still a hazard present (voltage on the
terminal block). The LED remains amber and is active to
around 20V +/-5V. The LED is not illuminated if the input
is below 15V.
FAN OK A bi-color LED indicates Green The LED illuminates s green when all fans are
power supply fan status operational.
Red The LED illuminates red when a fan failure is detected.
OUTPUT FAIL Power supply activity Red When the LED is off, it signals that the DC output voltage
are within the normal operating range. Output voltage
between the minimum and maximum limits will not
create an output fail alarm, and output voltages below the
minimum or above the maximum will create an Output
Fail alarm.
Led illuminates red to indicate that the DC output is out
of the specified range.
When you turn the power supply on, the red LED
illuminates for two to three seconds to test LED operation
before going off.
The output voltage alarm is declared when the output voltage is below the low end of the minimum or
above the high end of the maximum limits. When the output voltage is above the high end of the
minimum or below the low end of the maximum limits, the Red state will not be activated.
Table 6-4 shows the DC power supply output voltage alarm range.
Table 6-4 DC Power Supply Output Voltage Alarm Threshold Ranges
Output Minimum Maximum

12V 10.0-11.2V 12.8-13.8V
3.3V 2.6 - 3.0V None
Cisco ASR 1002 Router is designed for standalone, two rail 19-inch rack-mount (front rail only), four
rail 19-inch rack-mount (front and rear rail).
mount the chassis on an equipment shelf or tabletop.
OL-13208-03 6-9

chassis to make the chassis lighter for your rack installation, such as the power supplies.
Statement 1071

• The Cisco ASR 1002 Router requires a minimum of 3.5 inches or 8.9 cm rack units of vertical rack
space. Measure the proposed rack location before mounting the chassis in the rack.
• Maintain a minimum clearance of 3 inches on the front and back sides of the chassis for the cooling
air inlet and exhaust ports, respectively. Avoid placing the chassis in an overly congested rack or
directly next to another equipment rack; otherwise, the heated exhaust air from other equipment can
enter the inlet air vents and cause an overtemperature condition inside the router.
6-10 OL-13208-03

conditions in the “Site Environmental Requirements” section on page 3-8.

Depth 22.50 in. (57.15 cm)
supply handles).
Height 3.47 in. (8.813 cm) - 2RU rack-mount per EIA RS-310
Width 17.25 in. (43.815 cm) - 19 inch rack-mount
Weight 40 lb (18.143 k) - fully configured

or tabletop.
• Always follow proper lifting practices as outlined in the “Electrical Safety” section on page 3-18,
when handling the chassis.
OL-13208-03 6-11


FANS
FAN
OK MULTI-
FAILURE
FAN
FAILURE
When hot CAUTION

removal swapping
this fan
shutdown minutes
will occur. or
1
2
3
4
0A
CISCO PROC 0B
ESSOR
10000 CISCO ONLY 5
10000 CISCO
6
FAIL
10000 CISCO
7
FAIL
10000 CISCO
8
FAIL
10000 CISCO
FAIL
10000
CISCO
10000 CISCO
10000 CISCO
FAIL
10000 CISCO
FAIL
CO
10000
FAIL
NS
OLE CO
FAIL
NS
CAR
OLE
ALA
AUX
CAR
RIER
LOO
RM
ALA
RIER
LOO
P
AUX
RM
0
P
0 ACT
IVIT
CAR
ETH Y ACT
ALA
CAR
IVIT
RIER
ER
LOO
SLO
ALA
LIN
RM
NE ETH
SLO
Y
RIER
CAR
LOO
K T
P
RM
1 ER
T
ALA
0
T
SLO
RIER
LIN
0
NE
LOO
SLO
1
1 0
RM
K T
T
P
T
0
0
1
2 1
2 1
POWER 1
FAULT
MISWIR 3
E 2
3 2
LINK
CAR
TX
ALA
RX
2
RIER
LOO
RM
4 3
4 3
3
5
CAR
4
5 4
RIER
TX
4
RX
5
5
5
GIGABIT ETHERNET

CH OC-12-DSO SM-IR
AC
O
AC
CR O
6XCT3–DS0
ITIC
CR
6XCT3–DS0
MA AL
ITIC
JO
R MA AL
MIN
JO
OR
POWER MIN
R
OR
6XCT3–DS0
FAULT
6XCT3–DS0
MISWIR
6XCT3–DS0
STA
TU
FAI S STA
L TU
FAI S
L
PROC
ESSOR
ONLY
30007
Note The chassis in Figure 6-7 does not represent the Cisco ASR 1002 Router.
Step 4 Repeat Step 2 through Step 3 on the other side of the chassis. Use all screws to secure the rack-mount
Note The chassis rack-mount brackets must be installed first so that you can attach the
cable-management brackets to the chassis rack-mount brackets after the chassis is installed in
the rack.
attached cable-management brackets on the front of the Cisco ASR 1002 Router.
6-12 OL-13208-03

when you attach it to the chassis
US
A
C/
AT
ST
A
A/L
C/
A
A/L
S
C/
SPA-4XOC3-PO
A/L
C/
PWR STAT
3
A/L
CON
2
AUX
US
A
C/
AT
MGMT
ST
A
LINK
A/L
C/
MTS
A
CARRIER
A/L
S
C/
BOOT SPA-4XOC3-PO
A
3
QE3
A/L
C/
QE2
3
QE1
A/L
QE0
2
STAT
1
ASR 1002
0
US
A
C/
min
AT
stat
ST
A
A/L
C/
maj
A/L
S
C/
pwr SPA-4XOC3-PO
A
crit
A/L
C/
3
A/L
2
1
0
280280
1
1 Cable-management bracket top and bottom 3 Chassis front rack-mount bracket

screw
Step 8 Go to the “Attaching a Chassis Ground Connection” section on page 6-23 to continue the installation.

The Cisco ASR 1002 Router can be installed in an existing rack with equipment or in an empty rack with
no equipment: The chassis can be mounted in either rack types:
• Two-post rack, either 19 inch or 23 inch. Inner clearance (the width between the inner sides of the
two posts or rails) must be at least 19 inches (48.26 cm). The height of the chassis is 3.47 inches
(8.8 cm). Airflow through the chassis is from front to back.
Note If you are using a two-post rack secure the rack to the floor surface to prevent tipping and
avoid bodily.
OL-13208-03 6-13

• Four post, 19-inch equipment rack. Inner clearance (the width between the inner sides of the two
posts or rails) must be at least 19 inches (48.26 cm). The height of the chassis is 3.47 inches (8.8
cm). Airflow through the chassis is from front to back.
Note When handling the chassis, always follow proper lifting practices, see Chassis-Lifting Guidelines, page
3-20.
The Cisco ASR 1002 Router can be installed with both front or rear rack-mount brackets.

equipment rack.
Mounting flanges
Minimum usable
(45.0 cm)
28014
Hole centerline
to hole centerline
(46.5 cm ± 0.15 cm)
6-14 OL-13208-03


Note The cable-management brackets are attached to the chassis after you install the chassis rack-mount
brackets on the chassis and mount the chassis in the rack.

Figure 6-10 shows where to attach the front rack-mount brackets to the Cisco ASR 1002 Router.
US
A
C/
AT
ST
A
A/L
C/
A
A/L
S
C/
SPA-4XOC3-PO
A
A/L
C/
PWR STAT
3
A/L
CON
US
AUX
2
A
C/
AT
MGMT
1
ST
A
LINK
A/L
C/
3
MTS
0
CARRIER
A
A/L
S
C/
BOOT SPA-4XOC3-PO
A
QE3
A/L
C/
QE2
3
QE1
A/L
QE0
2
STAT
1
ASR 1002
0
US
A
C/
min
AT
stat
ST
A
A/L
C/
maj
A
A/L
S
C/
pwr SPA-4XOC3-PO
A
crit
A/L
C/
3
A/L
2
1
0
280278
2 1
1 Front rack-mount bracket ear and holes 3 Front rack-mount bracket screws
2 Front rack-mount bracket
Step 2 Position the front rack-mount bracket top hole with the chassis first top hole behind the side vent holes.
OL-13208-03 6-15

Step 5 Install the chassis in a rack. To install the Cisco ASR 1002 Router in a rack, go to the Installing the Cisco

To install the rear rack-mount brackets on a Cisco ASR 1002 Router, complete the following steps:
Step 1 Locate the threaded holes on the rear side of the chassis. Make certain that you hold the rear rack-mount
bracket with the ear and holes facing outward and towards the rear of the chassis.
280279
2 1
1 Rear rack-mount bracket ear and holes 3 Rear rack-mount bracket screws
2 Rear rack-mount bracket
Step 2 Position the rear rack-mount bracket top hole with the chassis top hole from the back.
Step 4 Repeat Step 1 through Step 3 on the other side of the chassis. Use the remaining screws to secure the
rear rack-mount brackets to the chassis.
Caution To make installation easier, before you mount the ASR 1002 Router in a rack, make certain you read
which rack-mount bracket ear holes to use when positioning the chassis in the rack. As a result of using
the designated ear holes on the rack-mount bracket, the cable-management bracket installation will be
made easier.
6-16 OL-13208-03


your safety:
Tip To allow space to attach the cable-management brackets to the chassis in the rack easily, make
certain that you use the rack-mount bracket ear holes specified in the next steps.
Step 7 Hold the chassis in position against the mounting rails in the equipment rack and follow these steps:
a. Insert the bottom screw into the second hole up from the bottom of the rack mount ear and use a
hand-held screwdriver to tighten the screw to the rack rail.
Tip To make installation easier, insert one screw at the bottom of the chassis and the next screw at
the top of the chassis diagonally from the first screw.
OL-13208-03 6-17

b. Insert the top screw into the second hole from the top of the rack mount ear diagonally from the
bottom screw and tighten the screw to the rack rail.
c. Insert the four screws to secure the chassis to the rack equipment.
Tip As a result of using the specified rack-mount bracket ear holes, the cable-management bracket can be
easily attached to the rack-mount bracket when the chassis is in the rack.

(48.26 cm). The height of the chassis is 3.47 inches (8.8 cm). Airflow through the chassis is from front
to back.
6-18 OL-13208-03

US
C/A
AT
ST
C/A
A/L
C/A
A/L
SPA-4XOC3-POS
C/A
A/L
3
A/L
US
C/A
AT
1
ST
C/A
A/L
0
C/A
A/L
SPA-4XOC3-POS
C/A
A/L
3
A/L
2
1
ASR 1002
0
US
C/A
min
AT
stat
ST
C/A
A/L
maj
C/A
A/L
pwr SPA-4XOC3-POS
C/A
crit
A/L
3
A/L
2
1
0
280282
2
1
1 Rack equipment rail 2 Rack-mount bracket ear and holes

3-20.
(48.26 cm). The height of the chassis is 3.47 inches (8.8 cm). Airflow through the chassis is from front
to back.
OL-13208-03 6-19

to support the chassis. Using two people, lift the chassis into the rack using the side handles and grasping
Note Use the second hole up from the bottom of the rack-mount bracket and the second hole down from the
top of the rack-mount bracket. This will make it easier to attache the cable-management bracket to the
chassis in the equipment rack.
to the rack rails on each side of the chassis.
Step 4 Finger-tighten screws to the rack rails on each side of the chassis.
Figure 6-13 Cisco ASR 1002 Router in a Four Post Rack - Front and Rear Rack-Mounting
US
C/A
AT
2
C/A
ST
A/L
C/A
A/L
SPA-4XOC3-POS
C/A
A/L
3
A/L
US
C/A
AT
1
C/A
ST
A/L
0
C/A
A/L
SPA-4XOC3-POS
C/A
A/L
3
A/L
2
1
ASR 1002
0
US
C/A
min
AT
stat
C/A
ST
A/L
maj
C/A
A/L
pwr SPA-4XOC3-POS
C/A
crit
A/L
3
A/L
2
1
0
280281
3
4
1 Rear rack equipment rail 3 Front rack-mount bracket ear and holes
2 Rear rack-mount bracket ear and holes 4 Front rack equipment rail
6-20 OL-13208-03

This completes the procedure for installing the chassis in the rack. Proceed to the “Attaching the
Cable-Management Bracket” section on page 6-21 to continue the installation.

The cable-management brackets for the Cisco ASR 1002 Router contain one independent
slot.
to the chassis.
in the rack:
Note Use the package of screws that came with your chassis containing four screws.
Figure 6-14 shows where to attach the front rack-mount brackets to the Cisco ASR 1002 Router in a rack.
OL-13208-03 6-21

Figure 6-14 Chassis Rack-Mount Bracket Ear Holes for the Cable-Management Bracket
US
A
C/
AT
ST
A
A/L
C/
A
A/L
S
C/
SPA-4XOC3-PO
A/L
C/
PWR STAT
3
A/L
CON
2
AUX
US
A
C/
AT
MGMT
ST
A
LINK
A/L
C/
MTS
A
CARRIER
A/L
S
C/
BOOT SPA-4XOC3-PO
A
3
QE3
A/L
C/
QE2
3
QE1
A/L
QE0
2
STAT
1
ASR 1002
0
US
A
C/
min
AT
stat
ST
A
A/L
C/
maj
A/L
S
C/
pwr SPA-4XOC3-PO
A
crit
A/L
C/
3
A/L
2
1
0
280280
1
1 Secure the cable-management top screw and 3 Front rack-mount bracket

bottom to this ear hole
This completes the procedure for installing the cable-management brackets on the chassis.
6-22 OL-13208-03


Connecting the Cisco ASR 1002 chassis to earth ground is required for all DC powered installations and
any AC powered installation where compliance with Telcordia grounding requirements is necessary.
Caution The dual-lug chassis ground stud must be installed, all cards or filler plates must be fully inserted and
screwed in and earthed to prevent a potential hazard in a telecom line.
(earth) connection for the chassis. The chassis ground lug (two) and the respective screws (four) are
provided in the accessory kit that ships with your Cisco ASR 1002 Router.
disconnected.
• Dual-lug chassis ground component (two) and respective screws (four) (shipped with the accessory
kit)
• Grounding wire
Figure 6-15 shows the location of the dual ground lug on the side of the of Cisco ASR 1002 Router.
OL-13208-03 6-23

Figure 6-15 Cisco ASR 1002 Router Chassis Ground Lug Location and Side Panel Door
1
2
TUS
C/A
STA
C/A
A/L
C/A
A/L
3-POS
SPA-4XOC
C/A
A/L
PWR STAT
3
A/L
CON
TUS
AUX
C/A
MGMT
STA
1
C/A
LINK
A/L
MTS
C/A
A/L
CARRIER 3-POS
BOOT SPA-4XOC
C/A
QE3
A/L
QE2
3
QE1
A/L
QE0
2
STAT
1
ASR 1002
0
TUS
C/A
min
STA
stat
C/A
A/L
maj
C/A
A/L
pwr SPA-4XOC
3-POS
C/A
crit
A/L
3
A/L
2
4
1
0
280283
3
1 F0 with ASR1000-ESP5 or ESP10. 3 The eUSB panel door on the side of the Cisco
ASR 1002 Router must not be opened. If there
is a problem with eUSB flash card, the chassis
should be returned.
2 R0 slot with embedded ASR1000-RP1 and 4 Cisco ASR 1002 Router ground stud location.
embedded ASR1000-SIP10.
To attach the grounding lug to the chassis ground connector on your chassis, follow these steps:
Step 2 Insert the AWG #6 wire into the wire receptacle on the grounding lug. Use the manufacturers’s
recommended crimping tool to carefully crimp the wire receptacle around the wire; this step is required
to ensure a proper mechanical connection.
4 2
50536
1 Chassis ground connector holes 3 Ground lug screws

2 Grounding lug 4 Ground wire
Step 3 Attach the grounding lug with the wire on the left to avoid having the grounding wire overlapping the
power supply.
6-24 OL-13208-03

280284
1 Chassis ground connector 2 Earth ground symbol
Step 5 Insert the two screws through the holes in the grounding lug.
This completes the procedure for attaching a chassis ground connection. Go to the following cabling
sections for information on attaching cables.

OL-13208-03 6-25


This section describes how to attach a cable to the Cisco embedded ASR1000-RP1 console or auxiliary
ports on the Cisco ASR 1002 Router. The Cisco ASR 1002 Router uses RJ-45 ports for both the auxiliary
port and console port to attach a modem or console terminal.
Caution Both the console and the auxiliary ports are asynchronous serial ports; any devices connected to these
device; for example, most modems are asynchronous devices.) To meet Class A emissions requirements,
shielded cables must be used for the console and auxiliary port connectors.
Before you can use the console interface on the router using a terminal or PC, you must perform the
following steps:
Step 2 Connect to the port using the RJ-45 to DB-9 cable.
Note For information about how to change the default settings to meet the requirements of your terminal or
host, refer to the Cisco IOS Terminal Services Configuration Guide.
Figure 6-18 Cisco ASR 1002 Router Embedded ASR1000-RP1 Console and Auxiliary Port
Connectors
1 2
C/A
PWR STAT
A/L
CON
AUX
MGMT
1
LINK
MTS
CARRIER 0
BOOT
C/A
QE3
280285
QE2
QE1
QE0 A/L
STAT
1
ASR 1002
0
US
C/A
min
AT
stat
ST
C/A
A/L
maj
C/A
pwr
A/L
3-POS
SPA-4XOC
C/A
crit
A/L
3
A/L
2
1
0
1 CON—console port 2 AUX —auxiliary port
6-26 OL-13208-03

Management Ethernet Port Cable Connection
Caution To comply with Class A emissions requirements, a shielded Ethernet cable must be used for the
connection.
To use the Management Ethernet interface on the router, perform the following steps:
Step 1 Insert an Ethernet RJ-45 cable into the MGMT ETHERNET port (see Figure 6-19).
Figure 6-19 Cisco ASR 1002 Router Embedded ASR1000-RP1 Management Port Connector
C/A
PWR STAT
A/L
CON
AUX
MGMT
1
LINK
MTS
0
CARRIER
BOOT
C/A
QE3
280286
QE2
QE1
A/L
QE0
STAT
1
ASR 1002
0
US
C/A
min
AT
stat
ST
C/A
A/L
maj
C/A
pwr
A/L
3-POS
SPA-4XOC
C/A
crit
A/L
3
A/L
2
1
0
1 MGMT - management port and cable
Step 2 Insert the other end of the RJ-45 cable to your management device or network.

Statement 1046
Statement 1003
OL-13208-03 6-27

Statement 1030
This section provides the procedures for connecting AC-input and DC-input power to your
Cisco ASR 1002 Router.
Cisco ASR 1000

Series Router DC
Cisco ASR 1004 24 30 40 10 8
Cisco ASR 1002 16 20 30 12 10
Note Detailed instructions for removing and replacing the Cisco ASR1002 Router AC and DC power supplies
are in Removing and Replacing a Cisco ASR 1002 Router Power Supply, page 8-40.
Read the safety warnings before you begin.
Warning Never install an AC power module and a DC power module in the same chassis. Statement 1050
Warning When installing or replacing the unit, the ground connection must always be made first and
disconnected last. Statement 1046
6-28 OL-13208-03

Warning This unit has two power supply connections. All connections must be removed to de-energize the unit.
Statement 1028
the protective device is rated not greater than: AC power supplies 20 A and DC power supplies 30 A.
Statement 1005

To connect AC power to the Cisco ASR 1002 Router, follow these steps:
Step 1 At the rear of the router, check that the power switch is in the Off (O) position.
Note Turn the power switch to the On (I) position after both sides of the power cord are connected.
Figure 6-20 Cisco ASR 1002 Router AC Power Supply Labels
1 2 3 4 5 6


280288
1
8 7

Step 2 Insert the AC power cable into the power supply AC inlet.
Step 3 To ensure that the AC power cord does not interfere with other cables or wires, dress the AC power cable
in one of the following ways.
a. Leave a small service loop in the AC power cord from the inlet and then secure the power cord
through the AC power supply handle as shown in Figure 6-21. Or go to step b.
OL-13208-03 6-29

Figure 6-21 Positioning Cisco ASR 1002 Router AC Power Supply and Cord in Slot 1
OUTPUT
INPUT
FAN
FAIL
OK OK
This unit
might
one power have more than
sup
All connec ply connection.
tion
to de-ene s must be remove
rgize the d
unit.
280383
1
1 AC power cord
b. Take the power cord and run it below the handles of the right and left power supplies. Make sure the
power cord is hanging loose so that it will not be disconnected from the AC power inlet as shown in
Figure 6-22.
Figure 6-22 Cisco ASR 1002 Router AC Power Supply in Slot 0 and Slot 1 With Power Cord
OUTPUT
INPUT
FAN
FAIL
OK OK
This unit
might have
one powe more
r supply conne than
All conne ction.
ctions
to de-energize must be removed
the unit.
OUTPUT
INPUT
FAN
FAIL
OK OK
This unit
might have
one powe more
r supply conne than
All conne ction.
ctions
the unit.
280377
6-30 OL-13208-03

Caution Do not run the AC power cord through the power supply handles as shown in Figure 6-23.
Figure 6-23 Incorrect Cabling on Cisco ASR 1002 Router AC Power Supply
OUTPUT
INPUT
FAN
FAIL
OK OK
This unit
might have
one powe more
r supply conne than
All conne ction.
ctions
the unit.
OUTPUT
INPUT
FAN
FAIL
OK OK
This unit
might have
one powe more
r supply conne than
All conne ction.
ctions
the unit.
280378
Note Using a tie wrap for the AC power cable is optional and not necessary. However, if you do attach
the AC power cable to a power supply tab and then you remove the AC power cable for some
reason, check for any damage to the cable after you cut the tie wrap off. If the power cord is
damaged, replace it immediately.
This completes the procedure for connecting an AC power supply in the Cisco ASR 1002 Router.

The DC power supply input connector is a euro-style terminal block. A means to provide strain relief to
the input wires is provided on the power supply. The connection order is negative (–), positive (+), and
GND; but this is the order from left to right that the terminals appear on the power supply, not the order
in which the leads should connected during installation. The order the leads should be attached is GND,
positive (+), and negative (-).
The recommended branch circuit breaker for the Cisco ASR 1002 Router DC power supply is 30Amp.
Use a AWG #10 wire gauge on the 30Amp circuit.
OL-13208-03 6-31

Figure 6-24 shows the DC power supply for the Cisco ASR 1002 Router.
Figure 6-24 DC Power Supply for the Cisco ASR 1002 Router
1 2 3 4 5 6


280289
1
-48V/-60V 16A -48V/-60V 16A
7
10 9 8


indicates voltage is greater than 43.5VDC at turn-on and remains green down
presence of to 39VDC.
input voltage Amber The LED illuminates amber if the power supply turns off due to low
input voltage (falls below 39VDC) and indicates that there is still a
hazard present (voltage on the terminal block). The LED remains
amber and is active to around 20V +/-5V. The LED is not illuminated
if the input is below 15V.
6-32 OL-13208-03


supply fan status
Output Fail alarm.
Led illuminates red to indicate that the DC output is out of the
specified range.
This section describes how to connect the DC power supply in a Cisco ASR 1002 Router.
Note The color coding of the DC-input power supply leads depends on the color coding of the DC power
source at your site. Typically, green or green/yellow is used for ground. Make certain the lead color
coding you choose for the DC-input power supply matches lead color coding used at the DC power
source.
Statement 1046
Step 1 At the rear of the router, check that the power supply Standby switch is in the Standby (see Figure 6-25)
position.
Step 2 Ensure that the negative and positive leads are disconnected from the site power source.
OL-13208-03 6-33

Figure 6-25 Cisco ASR 1002 Router DC Power Supply Terminal Block Cable Connections
OUTPUT
INPUT
FAN
FAIL
OK OK
This unit
might
sup
tion
rgize the d
unit.
2
3
-48V/-60V
16A
280290
1
1 Earth ground lead with service loop and 3 Negative lead

tie-wrap
2 Positive lead 4 DC power supply Standby switch
Step 3 Using a wire stripper, strip approximately 0.55 inch (14 mm) from the negative, positive, and ground
lead.
Step 4 Insert the stripped end of the ground lead all the way into the ground lead receptacle on the DC-input
power supply, and tighten the receptacle screw using a 3.5mm flat-blade screwdriver to a torque of 0.5
to 0.6Nm.
Step 5 Insert the stripped end of the positive lead all the way into the positive lead receptacle and tighten the
receptacle screw using the same 3.5mm flat-blade screwdriver. Repeat this step for the negative lead.
Note Make sure the entire stripped end of each lead is inserted all the way into its receptacle. If any
exposed wire at the stripped end of a lead is visible after inserting the lead into its receptacle,
remove the lead from the receptacle, use the wire stripper to cut the stripped end of the lead, and
repeat Step 3 through Step 5.
Step 6 After tightening the receptacle screw for the ground, positive, and negative DC-input leads, use a cable
tie to secure the three leads to the power supply faceplate, as shown in Figure 6-25. When securing the
ground, positive, and negative DC-input leads to the power supply faceplate, leave a small service loop
in the ground lead to ensure that the ground lead is the last lead to disconnect from the power supply if
a great deal of strain is placed on all three leads as shown in Figure 6-25.
Caution Make certain that the earth ground lead wire has a service loop before you tie wrap the lead wires to
prevent the ground from being disconnected.
6-34 OL-13208-03

Connecting a Terminal to the Cisco ASR1000-RP1 Console Port
Step 7 Connect the ground, positive, and negative leads to the power source.
Step 8 Turn the branch source breaker on.
Step 9 Place the DC Standby switch in the On (I) position. The power supply LEDs light when power is
supplied to the router.
You have completed the procedure for connecting a DC power supply in the Cisco ASR 1002 Router.
Connecting a Terminal to the Cisco ASR1000-RP1 Console Port

The Cisco ASR 1002 embedded router processor has an asynchronous serial (EIA/TIA-232) RJ-45
console port labeled CON on its front panel. You can connect this port to most types of video terminals
through use of the console cable kit that is included with your Cisco ASR 1002 Router. The console
cable kit contains:
Step 1 Connect one end of the RJ-45 cables to the serial RJ-45 port (CON) on the Cisco embedded
ASR1000-RP1 (Figure 6-26).
Figure 6-26 Cisco ASR 1002 Router Console Port Connection on Cisco Embedded ASR1000-RP1
1 2
C/A
PWR STAT
A/L
CON
AUX
MGMT
1
LINK
MTS
0
CARRIER
BOOT
C/A
QE3
280285
QE2
QE1
A/L
QE0
STAT
1
ASR 1002
0
US
C/A
min
AT
stat
ST
C/A
A/L
maj
C/A
pwr
A/L
3-POS
SPA-4XOC
C/A
crit
A/L
3
A/L
2
1
0
OL-13208-03 6-35

Connecting Cables
Step 5 Configure your video terminal to match the following default console port settings:
• 9600 baud
• 8 data bits
• No parity generation or checking
• 1 stop bit
• No flow control
Step 6 Go to the “Connecting Cables” section on page 6-36 to continue the installation.
Connecting Cables
Processor 1, labeled AUX. For the AUX port connection, see Figure 6-18.
Step 2 Run the cable up and through the cable-management bracket and connect the other end of the cable to
your modem.
6-36 OL-13208-03

C H A P T E R 7
Cisco ASR 1000 Series Routers Power Up and
Initial Configuration
This chapter guides you through a basic router configuration, which is sufficient for you to access your
network. Complex configuration procedures are beyond the scope of this publication and can be found
in the modular configuration and modular command reference publications in the Cisco IOS software
configuration documentation set that corresponds to the software release installed on your Cisco
hardware.
To configure a Cisco ASR 1000 Series Router from a console, you need to connect a terminal to the
router console port.
This chapter contains the following topics:
• Checking Conditions Prior to System Startup, page 7-1
• Verifying Power Supply Operation, page 7-2
• Configuring the Cisco ASR 1000 Series Routers at Startup, page 7-7
• Power Off the Cisco ASR 1000 Series Router, page 7-10
Checking Conditions Prior to System Startup

Ensure that the following conditions are met before starting up the router:
• The shared port adapter is inserted in its slot.
• The network interface cable is connected.
• The optional Fast Ethernet Management port cable is installed.
• The chassis is securely mounted and grounded.
• The power and interface cables are connected.
• Your PC with terminal emulation program (hyperTerminal or equivalent) is connected to the console
port and powered up.
• Your PC terminal emulation program is configured for 9600 baud, 8 data bits, 1 stop bit, no parity,
and flow control is set to none.
Cisco ASR 1000 Series Aggregation Services Routers Installation and Initial Configuration Guide
OL-13208-03 7-1

Chapter 7 Cisco ASR 1000 Series Routers Power Up and Initial Configuration
Verifying Power Supply Operation
• You have selected passwords for access control.

• Captive installation screws are tight on all removable components.
• The console terminal is turned on.
• You have determined the IP addresses for the Ethernet and serial interfaces.
• Empty card slots or card bays are filled with card blanks. This ensures proper air flow through the
chassis and electromagnetic compatibility (EMC).
You are now ready to start your router.
Verifying Power Supply Operation

Follow this procedure to verify power supply is operating correctly.
Step 1 Check that the power supply LEDs are:

• INPUT OK is green
• FAN OK is green
• OUTPUT FAILED is not illuminated
Step 2 To ensure that the power supply state is OK, type the show platform command. This output sample is
from a Cisco ASR1006 router. The other Cisco ASR1000 routers display similar type of output.
MCP_SCAL_R1#sho plat
Chassis type: ASR1006
The following output displays:
Slot Type State Insert Time

1 ASR1000-SIP10 ok 00:03:19
1/1 SPA-8X1GE-V2 ok 00:02:23
2 ASR1000-SIP10 ok 00:03:19
2/0 SPA-1X10GE-L-V2 ok 00:02:22
2/1 SPA-8X1GE-V2 ok 00:02:17
R0 ASR1000-RP1 ok,active 00:03:19
F0 ASR1000-ESP20 ok,active 00:03:19
P0 ASR1006-PWR-AC ok 00:02:50
P1 ASR1006-PWR-AC ps, fail 00:02:50
Slot CPLD Version Firmware

Version
1 07091401 12.2(33r)XN2
2 07091401 12.2(33r)XN2
R0 08060301 12.2(0:0)
F0 08041102 12.2(33r)XN2
MCP_SCAL_R1#
If the LEDs indicate a power problem or the power supply state is ps,fail, then contact a customer service
representatives for assistance or additional instructions.
7-2 OL-13208-03

Powering Up the Cisco ASR 1000 Series Routers

Make certain that all card slots and compartments are closed off. Install blank faceplates on any empty
slots. Always have power supply slots filled. If you leave a power supply slot uncovered, then you risk
exposure to hazardous voltages on the power pins on the midplane.
After installing your Cisco ASR 1000 Series Routers and connecting cables, start the router.
Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to
hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI)
that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not
operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement
1029
Note There is no cover on the Cisco ASR 1002 router DC power supply terminal block; therefore,
Statement 1029 does not apply to the Cisco ASR 1002 router.
You are now ready to power on the system for the first time. Follow these steps.
Step 1 Before you power on, make sure that:

a. The AC cord is plugged into the AC power inlet.
b. All cables are connected.
c. Your computer is powered up and connected.
Note To view the boot sequence, you must have a console connection to the Cisco ASR 1000 Series
Routers before it powers up.
Step 2 Move the power switch to the ON position. Listen for the fans; you should immediately hear them
operating.
Step 3 Depending on your installation, some LEDs on the rear of the chassis and on installed modules also come
on.
Caution Do not press any keys on the keyboard until the messages stop and the SYS PWR LED is solid green.
Any keys pressed during this time are interpreted as the first command typed when the messages stop,
which might cause the router to power off and start over. It takes a few minutes for the messages to stop.
Note This is only an example of what can display. The system boots differently depending upon the
configuration that ships with your system.
Step 4 Observe the initialization process. When the system boot is complete (a few seconds), the Cisco
ASR 1000 RP1 begins to initialize.
Example 7-1 Loading the Default System Boot Image
rommon 1 >
OL-13208-03 7-3

rommon 1 > boot

Located rp_super.ppc.nader.5g.evfc.bin
Image size 211681484 inode num 12, bks cnt 51681 blk size 8*512
#######################################################################################
#######################################################################################
#######################################################################################
################################
#######################################################################################
################################
#############################################
Boot image size = 211681484 (0xc9e00cc) bytes
Using midplane macaddr

Package header rev 0 structure detected
Calculating SHA-1 hash...done
validate_package: SHA-1 hash:
calculated 479a7d62:6c128ba8:3616b8da:93cb3224:5c1aeb34
expected 479a7d62:6c128ba8:3616b8da:93cb3224:5c1aeb34
Image validated
PPC/IOS XE loader version: 0.0.3

loaded at: 00800000 0D1E2004
zimage at: 00807673 009B8C69
initrd at: 009B9000 01006219
isord at: 01007000 0D1DF800
avail ram: 00400000 00800000
Kernel load:
Uncompressing image... dst: 00000000 lim: 00400000 start: 00807673 size: 001B15F6...done.
Now booting the IOS XE kernel
Restricted Rights Legend
Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.

San Jose, California 95134-1706
7-4 OL-13208-03


Cisco IOS-XE software, Copyright (c) 1986-2008 by Cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are

licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to

[email protected].
cisco ASR1002 (RP1) processor with 541737K/6147K bytes of memory.

4 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
1869396K bytes of physical memory.
7798783K bytes of eUSB flash at bootflash:.
--- System Configuration Dialog ---
Would you like to enter the initial configuration dialog? [yes/no]: no
Press RETURN to get started!
*Feb 19 17:34:27.361: % Error opening nvram:/ifIndex-table No such file or directory

*Feb 19 17:34:28.235: %ASR1000_MGMTVRF-6-CREATE_SUCCESS_INFO: Management vrf Mgmt-intf
created with ID 4085, ipv4 table-id 0xFF5, ipv6 table-id 0x1E000001
*Feb 19 17:34:29.720: %PARSER-4-BADCFG: Unexpected end of configuration file.
*Feb 19 17:34:29.809: %NETCLK-5-NETCLK_MODE_CHANGE: Network clock source not available.

The network clock has changed to freerun
*Feb 19 17:34:10.138: %CPPHA-7-SYSREADY: F0: cpp_ha: CPP client process FMAN-FP (5 of

5) ready.
*Feb 19 17:34:29.824: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
OL-13208-03 7-5

*Feb 19 17:34:10.269: %IOSXE-6-PLATFORM: F0: cpp_cp: cpp_mlp_svr_client_bind:

cpp_mlp_svr_ifm_init() successful
*Feb 19 17:34:10.362: %CPPHA-7-START: F0: cpp_ha: CPP 0 preparing image
/usr/cpp/bin/cpp-mcplo-ucode
*Feb 19 17:34:10.473: %CPPHA-7-START: F0: cpp_ha: CPP 0 startup init image
*Feb 19 17:34:14.688: %CPPHA-7-START: F0: cpp_ha: CPP 0 running init image
*Feb 19 17:34:14.919: %CPPHA-7-READY: F0: cpp_ha: CPP 0 loading and initialization
complete
*Feb 19 17:34:14.919: %CPPHA-6-SYSINIT: F0: cpp_ha: CPP HA system configuration start.
*Feb 19 17:34:15.179: %IOSXE-6-PLATFORM: F0: cpp_cp: Process
CPP_PFILTER_EA_EVENT__API_CALL__REGISTER
*Feb 19 17:34:15.286: %CPPHA-6-SYSINIT: F0: cpp_ha: CPP HA system enabled.
*Feb 19 17:34:15.287: %CPPHA-6-SYSINIT: F0: cpp_ha: CPP HA system initializaton
complete.
*Feb 19 17:34:30.823: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0,
changed state to down
*Feb 19 17:35:12.865: %LINK-5-CHANGED: Interface GigabitEthernet0/0/0, changed state to
administratively down
*Feb 19 17:35:13.865: %LINEPROTO-5-UPDOWN: Line protocol on Interface
GigabitEthernet0/0/0, changed state to down
*Feb 19 17:35:19.167: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 0/0, interfaces
disabled
*Feb 19 17:35:19.171: %ASR1000_OIR-6-INSCARD: Card (fp) inserted in slot F0
*Feb 19 17:35:19.171: %ASR1000_OIR-6-ONLINECARD: Card (fp) online in slot F0
*Feb 19 17:35:19.187: %ASR1000_OIR-6-INSCARD: Card (cc) inserted in slot 0
*Feb 19 17:35:19.187: %ASR1000_OIR-6-ONLINECARD: Card (cc) online in slot 0
*Feb 19 17:35:19.189: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 0/0
*Feb 19 17:35:19.452: %SYS-5-RESTART: System restarted --
Cisco IOS-XE software, Copyright (c) 1986-2008 by Cisco Systems, Inc.*Feb 19
17:35:19.455: %SYS-6-BOOTTIME: Time taken to reboot after reload = 78809 seconds
*Feb 19 17:35:19.551: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
7-6 OL-13208-03

Configuring the Cisco ASR 1000 Series Routers at Startup
*Feb 19 17:35:21.669: %DYNCMD-7-CMDSET_LOADED: The Dynamic Command set has been loaded
from the Shell Manager
Router>
Step 5 During the boot process, observe the system LEDs. The LEDs on the shared port adapter go on and off
in irregular sequence. They may go on, go out, and go on again for a short time. On the router, the green
STATUS LED comes on and stays on.
Verifying the Front Panel LEDs

The front-panel indicator LEDs provide power, activity, and status information useful during bootup. For
more detailed information about the LEDs, refer to Chapter 2, “Cisco ASR 1000 Series Routers
Components.”
Verifying the Hardware Configuration

To display and verify the hardware features, enter the following commands:
• show version—Displays the system hardware version; the installed software version; the names and
sources of configuration files; the boot images; and the amount of installed DRAM, NVRAM, and
flash memory.
• show diag slot—Displays the IDPROM information for the assemblies in the chassis.
Checking Hardware and Software Compatibility

To check the minimum software requirements of the Cisco IOS software with the hardware installed on
your Cisco ASR 1000 Series Routers, Cisco maintains the Software Advisor tool on Cisco.com. This
tool does not verify whether Cisco ASR 1000 Series SIPs or SPAs within a system are compatible; but
the tool provides the minimum Cisco IOS requirements for individual hardware modules and
components.
Note To access this tool, you must have a Cisco.com login account.
To access the Software Advisor, click Login at Cisco.com, type Software Advisor in the search box,
and click Go. Click the link for the Software Advisor Tool.
Choose a product family or enter a specific product number to search for the minimum supported
software needed for your hardware.

This section explains how to create a basic running configuration for your Cisco ASR 1000 Series
Routers.
OL-13208-03 7-7

Note You need to acquire the correct network addresses from your system administrator or consult your
network plan to determine correct addresses before you can complete the router configuration.
Before continuing the configuration process, check the current state of the router by entering the show
version command. The show version command displays the release of Cisco IOS software that is
available on the router.
For information on modifying the configuration after you create it, see the Cisco IOS configuration and
command reference guides.
To configure a Cisco ASR 1000 Series Routers from the console, you must connect a terminal or
terminal server to the console port on the Cisco ASR 1000 Series RP1. To configure the Cisco ASR 1000
Series Routers over your management Ethernet, you must have the router’s IP address available.
Using the Console Interface

To access the command line interface using the console, follow these steps:
Step 1 Your system is booting and if you answer No, at the prompt:
Would you like to enter the initial configuration dialog? [yes/no]: no
Step 2 Then Press Return to enter user EXEC mode. The following prompt appears:
Router>
Step 3 From user EXEC mode, enter the enable command as shown in the following example:
Router> enable
Step 4 At the password prompt, enter your system password. If an enable password has not been set on your
system, this step may be skipped. The following example shows entry of the password called enablepass:
Password: enablepass
Step 5 When your enable password is accepted, the privileged EXEC mode prompt appears: Router#
Step 6 You now have access to the CLI in privileged EXEC mode and you can enter the necessary commands
to complete your desired tasks. To exit the console session, enter the quit command as shown in the
following example:
Router# quit
Configuring Global Parameters

When you first start the setup program, you must configure the global parameters. These parameters are
used for controlling system-wide settings. Complete the following steps to enter the global parameters:
Step 1 Connect a console terminal to the console port, and then boot the router.
7-8 OL-13208-03

Note This is only an example of the output display; prompts may vary.
When you see this information, you have successfully booted your router:
Restricted Rights Legend
Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.

San Jose, California 95134-1706
.
.
.
Would you like to enter the initial configuration dialog? [yes/no]: yes
Step 2 The first sections of the configuration script appear only at an initial system startup. On subsequent uses
of the setup facility, the script begins with a System Configuration Dialog as shown below: When asked
if you would like to enter the initial configuration dialog, enter yes.
Would you like to enter the initial configuration dialog? [yes/no] yes
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Basic management setup configures only enough connectivity for management of the
system, extended setup will ask you to configure each interface on the system.
Note Basic management setup configures enough connectivity for managing the system; extended setup will
ask you to configure each interface on the system. For detailed information about setting global
parameters, refer to the Cisco ASR 1000_Series Aggregation Services Routers Software Configuration
Guide.
Checking the Running Configuration Settings

To check the value of the settings you have entered, enter the show running-config command at the
Router# prompt:
Router# show running-config
OL-13208-03 7-9

Power Off the Cisco ASR 1000 Series Router
To review changes you make to the configuration, use the EXEC mode show startup-config command
to see the changes and copy run-start stored in NVRAM.
Saving the Running Configuration to NVRAM

To store the configuration or changes to your startup configuration in NVRAM, enter the copy
running-config startup-config command at the Router# prompt:
Router# copy running-config startup-config
Using this command saves the configuration settings that you created in the router using configuration
mode and the setup facility. If you fail to do this, your configuration will be lost the next time you reload
the router.
Power Off the Cisco ASR 1000 Series Router

This section explains how to shut down the Cisco ASR 1000 Series router. It is recommended that before
turning off all power to the chassis, you issue the reload command. This insures that the operating
system cleans up all the file systems. Once the reload operation is complete, then the Cisco ASR 1000
Series router can be powered off safely.
To remove power from the Cisco ASR 1000 Series Router, follow this procedure:
Step 1 Slip on the ESD-preventative wrist strap that was included in the accessory kit.
Step 2 Before you shutdown a power supply, issue the IOS reload command to halt the system and then wait
for ROM Monitor to execute before proceeding to the next step. The following screen shot shows an
example of the reload command:
Router#reload
Proceed with reload? [confirm]
*Jun 18 19:38:21.870: %SYS-5-RELOAD: Reload requested by console. Reload Reason:

Reload command.
Step 3 Remove any power cables from the Cisco ASR 1000 Series Router.
a. For power supplies with a circuit breaker switch, position the switch to the Off (O) position.
b. For power supplies with a Standby switch, place the Standby switch in the Standby position.
Note After powering off the router, wait a minimum of 30 seconds before powering it on again.
7-10 OL-13208-03

C H A P T E R 8
Replacing Cisco ASR 1000 Series Routers
This chapter provides information on removing and replacing field-replaceable units (FRUs). The
following information is in this chapter:
• Removing and Replacing the Cisco ASR 1000 Series RP1, page 8-1
• Removing and Replacing the Cisco ASR 1000 Series RP1 Internal Hard Drive, page 8-3
• Removing and Replacing the Cisco ASR 1000 Series RP1 DIMM Memory Module, page 8-9
• Removing and Replacing an eUSB Device, page 8-13
• Removing and Replacing the 1GB USB Flash Token Memory Stick, page 8-15
• Removing and Replacing the Cisco ASR 1000 Series Embedded Service Processors, page 8-17
• Removing and Replacing a SPA Interface Processor, page 8-19
• Removing and Replacing a Cisco ASR 1006 Router Power Supply, page 8-22
• Repacking the Box, page 8-48
Removing and Replacing the Cisco ASR 1000 Series RP1

The following sections describe the procedures for removing and replacing a Cisco ASR 1000
Series RP1 route processor in your Cisco ASR 1006 Router and Cisco ASR 1004 Router (The Cisco
ASR1000-RP1 in the Cisco ASR 1002 Router is not a field-replaceable unit because it is embedded into
the chassis).
Statement 1030
Warning During this procedure, wear grounding wrist straps to avoid ESD damage to any card. Do not directly
touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94
OL-13208-03 8-1

Chapter 8 Replacing Cisco ASR 1000 Series Routers Field-Replaceable Units
Removing and Replacing the Cisco ASR 1000 Series RP1
Note If you have two Cisco ASR 1000 Series RP1s in the Cisco ASR 1000 Series Router and you want to
remove one, do not power down the router. Remove the route processor and insert a new one, because
high availability provides for the other Route Processor to take on the processing tasks for the router.
Removing the Cisco ASR1000-RP1

To remove the Cisco ASR 1000 Series RP1 from the Cisco ASR 1000 Series Router, follow this
procedure:
Step 1 Slip on an ESD-preventive wrist strap and attach it to a chassis surface.

Step 2 If connected, remove any I/O cables from the Cisco ASR 1000 Series RP1.
Step 3 Using a number 2 Phillips or a 3/16-inch flat-blade screwdriver, loosen the two captive screws on the
faceplate of the Cisco ASR1000-RP1.
Step 4 Using the handles on both sides of the module, with two hands gently slide the module out of the chassis
slot.
Caution Handle the Cisco ASR 1000 Series RP1 by the carrier edges only; never touch the printed circuit board
components or connector pins.
Step 5 Place the Cisco ASR 1000 Series RP1 module on an antistatic surface with its printed circuit board
components facing upward or in a static shielding bag.
Note If you are returning the Cisco ASR1000 RP1 to the factory, immediately place it in a static shielding bag.
This completes the procedure for removing an installed Cisco ASR 1000 Series RP1 module from the
Cisco ASR 1006 Router and Cisco ASR 1004 Router.
Replacing the Cisco ASR1000-RP1

To replace the Cisco ASR 1000 Series RP1 in the Cisco ASR 1000 Series Router, follow this procedure:
Step 1 Attach an ESD-preventive wrist strap between you and an unfinished chassis surface.
Step 2 Remove the new Cisco ASR1000-RP1 from its static shielding bag.
Step 3 Using both hands, grasp the Cisco ASR1000-RP1 by its metal carrier edges and orient the it so that its
printed circuit board components are upward.
Caution Handle the Cisco ASR1000-RP1 by the carrier edges and handle only; never touch the printed circuit
board components or connector pins.
8-2 OL-13208-03

Removing and Replacing the Cisco ASR 1000 Series RP1 Internal Hard Drive
Step 4 Align the left and right edges of the Cisco ASR1000-RP1 printed circuit board between the Cisco
ASR1000-RP1 slot guides.
Step 5 Gently slide the Cisco ASR1000-RP1 all the way into its chassis slot until you feel the connectors seat
with the router midplane.
Step 6 Seat the Cisco ASR1000-RP1 in the router midplane by tightening its captive installation screws with a
number 2 Phillips or a 3/16-inch flat-blade screwdriver.
This completes the procedure for replacing the Cisco ASR1000-RP1 in a Cisco ASR1000 Series Router.
Removing and Replacing the Cisco ASR 1000 Series RP1 Internal
Hard Drive
The Cisco ASR 1000 Series RP1 contains an internal hard drive disk that provides nonvolatile storage
in the form of an internal flash disk. The Cisco ASR 1000 Series RP1 module can be configured with
either a 40 GB or a 32 GB disk. Both components are field-replaceable on the Cisco ASR 1006 Router
and the Cisco ASR 1004 Router (there is no hard disk in the Cisco ASR 1002 Router). On the front panel
of the Cisco ASR 1000 Series RP1, the DISK HD LED indicates activity on the hard drive.
This section explains how to remove a hard drive assembly from the Cisco ASR 1000 Series RP1 module
and replace it with a new internal hard drive.
Cisco ASR 1000 Series RP1 Spare Hard Drive Accessory Kit
The Cisco ASR 1000 Series RP1 spare hard drive ships with an accessory kit.Verify that the following
items have been shipped in the accessory kit before you remove and replace a damaged Cisco ASR 1000
Series RP1 module internal hard drive:
• Hard drive assembly
• Two cables and tie wrap
• One EMI wrist strap
• Document: Removing and Replacing the Cisco ASR 1000 Series RP1 FRU
Follow these procedures to remove and then replace the Cisco ASR 1000 Series RP1 internal hard drive
in a Cisco ASR 1000 Series Router.
Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly
touch the backplane with your hand or any metal tool, or you could shock yourself. Statement 94
OL-13208-03 8-3

Before you begin, read the following important notices:

• The reason you would be removing an internal hard drive is that it is failing or failed; so any data
recovery may be lost.
If the drive is functioning, you can back it up to a drive plugged into a USB port using the archive
tar command. At the router# prompt, type:
archive tar / create tarfile_dir_name file(s)_to_be_tarred

Example:
archive tar usb0: test_files harddisk: * This would theoretically copy the whole
harddisk to the device on usb0: under a tar file named test_files
• The new internal hard drive will be automatically partitioned and formatted when the system boots
up, if it is not correct, which means the drive was not previously formatted or was formatted in a
different manner than the Cisco ASR1000 requirements.
Removing the Cisco ASR 1000 Series RP1 and Internal Hard Drive from the Cisco
ASR 1000 Series Router
To remove the Cisco ASR 1000 Series Route Processor board from the Cisco ASR 1000 Series Router,
follow this procedure:
Step 1 Slip on the ESD-preventative wrist strap that was included in the accessory kit. Loosen the screw
fasteners on the Cisco ASR 1000 Series RP1 module.
Step 2 Perform an OIR shutdown on the Cisco ASR1000-RP1. At the router# prompt, type:
hw-module slot R (0 or 1) stop.
8-4 OL-13208-03

Figure 8-1 Cisco ASR 1000 Series Route Processor1 Internal Hard Drive Unit
1
1
2
280150
Step 3 Using the handles on both sides of the module, with two hands gently slide the Cisco ASR 1000 Series
RP1 out of the chassis.
Step 4 Place the module on a flat surface free of dust and dirt.
Step 5 Remove the internal hard drive cover:
a. Unscrew the fasteners.
b. Slide the cover off.
c. Lift the cover up from the board.
OL-13208-03 8-5

Figure 8-2 displays the Cisco ASR 1000 Series RP1 module with the hard drive cover removed.
Figure 8-2 Cisco ASR 1000 Series RP1 Module Hard Drive Cover and Screw Fastener
280151
Step 6 Using a # 2 Phillips screwdriver or a flat head screwdriver, loosen the screw fasteners and remove the
cover as shown in Figure 8-2.
Step 7 On the hard drive, unscrew the captive screw fastener.
Note Inspect the existing cables and replace them only if they are damaged. If you do not need to
replace them, leave the connection to the Cisco ASR 1000 Series Route Processor 1 in place and
only remove the connection to the internal hard drive.
Step 8 Carefully disconnect the cables at the rear of the hard drive. These cables are tie-wrapped in to prevent
them from disconnecting from the Cisco ASR 1000 Series RP1 itself. If the cables are not damaged,
leave the cables connected to the Cisco ASR 1000 Series Route Processor 1 with the tie wrap in place.
Remove the old hard drive.
8-6 OL-13208-03

Figure 8-3 shows the cables still connected because they do not have to be replaced.
Figure 8-3 Cisco ASR 1000 Series RP1 Module With Internal Hard Drive Removed
280152
Step 9 If the cables are damaged:
a. Remove the tie wrap around the cables.
b. Disconnect the cables from both the Cisco ASR 1000 Series Route Processor 1 connector and the
internal hard drive connector as shown in Figure 8-4.
Figure 8-4 shows the hard drive and cables removed in order to be replaced.
Figure 8-4 Cisco ASR 1000 Series RP1 Internal Hard Drive and Module Base 280153
OL-13208-03 8-7

This completes the procedure for disconnecting the Cisco ASR 1000 Series RP1 internal hard drive.
Replacing the Cisco ASR 1000 Series RP1 Internal Hard Drive
To replace the Cisco ASR 1000 Series RP1 internal hard drive and insert the Cisco ASR 1000 Series
Route Processor 1 into the Cisco ASR 1000 Series Router, follow these steps:
Step 1 On the Cisco ASR 1000 Series RP1, carefully align the new hard drive unit with its screw fastener to the
base screw on the bottom of the module.
Step 2 Reconnect the two cables to the rear of the hard drive. These are keyed for easy connection.
Figure 8-5 Cisco ASR 1000 Series RP1 Internal Hard Drive and Module Base
2
280154
1 Hard drive module fastener 2 Carrier mating fastener
8-8 OL-13208-03

Removing and Replacing the Cisco ASR 1000 Series RP1 DIMM Memory Module
Step 3 Align hard drive module to carrier base tabs, align the module fastener to base screw mate by hand, and
then tighten with screw driver.
Step 4 Replace the cover by aligning the tabs in the slot and tightening the screw fasteners.
Step 5 With two hands, grab the handles on the Cisco ASR 1000 Series RP1 module and slide it back into its
slot in the Cisco ASR 1000 Series Router and tighten the captive screw.
You have completed the replacement procedure for the Cisco ASR 1000 Series Route Processor 1
internal hard drive.
Removing and Replacing the Cisco ASR 1000 Series RP1 DIMM
Memory Module
The Cisco ASR 1000 Series RP1 memory interface supports two DDR-II SDRAM MiniDIMMs with
ECC protection.'
Note Unlike the Cisco ASR 1006 and ASR 1004, the DIMM memory interface is not field-replaceable on the
Cisco ASR 1002 router.
'This section provides instructions for upgrading or replacing the Cisco ASR 1000 Series RP1
MiniDIMM memory modules.
Note The Cisco ASR 1000 Series RP1 memory spares are sold as pairs. For example, the 2GB memory spare
(M-ASR1K-RP1-2GB=) is sold as a pair of 1GB modules and the 4GB memory spare
(M-ASR1K-RP1-4GB=) is sold as a pair of 2GB modules. Memory repairs or upgrades must utilize the
complete memory pairs as shipped from Cisco. For example, if 1 of the 2 memory modules were to fail
on the Cisco ASR 1000 RP1, then both memory modules must be removed and replaced with a spare
memory pair (as shipped from Cisco) and the failing memory should be returned as a pair to Cisco.
To prevent the system from operating incorrectly, do not mix modules from different vendors. The
modules might not be compatible with each other.
Warning During these procedures, wear grounding wrist straps to avoid ESD damage to the card. Do not
directly touch the backplane with your hand or any metal tool, or you could shock yourself.
Statement 94
Things you should know before you begin:

• Use an ESD-preventative wrist strap
• Back up any data that you want to save before replacing an eUSB device
• The card is keyed and slotted for easier connection
• Never wiggle the DIMM
• Handle the connector according to the instructions (see Figure 8-9).
OL-13208-03 8-9

To replace or upgrade the Cisco ASR 1000 Series DIMM memory spare, follow these steps:
Step 1 Attach an ESD-preventative wrist strap between you and an unpainted router surface.
Step 2 Locate the DIMM on the system board.
Note The DIMMs shown in Figures 8-6 and 8-7 are representative and might not look exactly like the
DIMMs used on the RP; but the procedure is the same.
Step 3 Press both spring latches outward to release the DIMM.
Figure 8-6 Cisco ASR 1000 Series RP1 DIMM Module Spring Latches
1 1
121392
1 Pull spring clips outward. 2 Pull DIMM out.
Step 4 Pull the latches away from the DIMM on both edges. This lifts the DIMM slightly. Gently lift the DIMM
free from the DIMM connector, taking care not to touch the pins that insert into the socket.
Step 5 Place the DIMM in an anti-static bag to protect the DIMM from ESD damage.
Caution Forcing the DIMM into the socket can damage the DIMM. Use the notches on the DIMM to align the
DIMM in the DIMM socket before inserting it (see Figure 8-7).
8-10 OL-13208-03

Figure 8-7 Cisco ASR 1000 Series RP1 DIMM Module Notch Location
103362
Polarization notch
Step 6 To install the DIMM memory card, locate the notches and align the DIMM with the socket before
inserting it.
Figure 8-8 Cisco ASR 1000 Series RP1 DIMM Module Alignment
280358
Note Hold the DIMM with two hands at its edge and insert the card.
Step 7 Make certain that both latches on the DIMM connector are open.
OL-13208-03 8-11

Step 8 Gently insert the new DIMM, taking care not to damage the pins on the edge of the DIMM.
Step 9 Carefully and firmly press the DIMM into the connector until the spring latches lock the DIMM in place
See Figure 8-6.
Caution Strong insertion force introduces excessive mechanical stress on the DIMM. To prevent any stress on the
soldering joints, there should be no up, down, or wiggling motion to be done on the DIMM during the
insertion as shown in Figure 8-9.
Figure 8-9 Handling Cisco ASR 1000 Series RP1 DIMM Module
280360
Step 10 Slide the DIMM one side at a time. Use light insertion force and insert smoothly; but make certain the
DIMM is inserted straight.
Note Make sure you perform steps 3 thru 11 for both DIMMs on the RP 1 before you replace the RP1 in the
system. Replace the Cisco ASR1000-RP1.All DIMMS must be replaced; not just one on the RP1
This completes the procedure for replacing a DIMM memory module on the Cisco ASR 1000 Series
RP1.
8-12 OL-13208-03

Removing and Replacing an eUSB Device

The Cisco ASR 1000 Series RP1 comes with an embedded eUSB (Embedded USB memory) flash device
that functions as the route processor NVRAM and BootDisk. The Cisco ASR 1000 Series Route
Processor 1 supports a 1GB eUSB flash field-replaceable unit on the Cisco ASR 1006 and
Cisco ASR 1004 router.
Note The 8 GB eUSB on the built-in route processor is not a field-replaceable unit (FRU) on the Cisco
ASR 1002 Router.
Before you physically replace the eUSB device, follow this procedure on the Cisco ASR1000-RP1.
Step 1 Make a backup of startup-config and prepare the router:

Step 2 To remove the Cisco ASR1000-RP and eUSB device from the chassis, follow these steps:
a. Attach an ESD-preventative wrist strap between you and an unpainted router surface.
b. If connected, remove any I/O cables from the Cisco ASR 1000 Series RP1.
c. Using a number 2 Phillips or a 3/16-inch flat-blade screwdriver, loosen the two captive screws on
the faceplate of the Cisco ASR1000-RP1.
d. Using the handles on both sides of the module, with two hands gently slide the module out of the
chassis slot.
Caution Handle the Cisco ASR 1000 Series RP1 by the carrier edges only; never touch the printed circuit board
e. Place the Cisco ASR 1000 Series RP1 module on an antistatic surface with its printed circuit board
components facing upward.
f. Locate the eUSB device on the ASR100-RP1 board. Figure 8-10 shows the location orientation of
the eUSB device on the Cisco ASR1000-RP1 board.
OL-13208-03 8-13

Figure 8-10 Cisco ASR1000-RP1 eUSB Location
272371
1 Cisco ASR1000-RP1 eUSB device location
g. Remove the small Phillips screw holding the eUSB board in-place.
Figure 8-11 Cisco ASR1000-RP1 eUSB Device
1
232372
1 Cisco ASR1000-RP1 eUSB device Phillips screw
h. Gently pull the eUSB device up from its connector and remove it.
i. Place the eUSB device in an anti-static bag.
8-14 OL-13208-03

Removing and Replacing the 1GB USB Flash Token Memory Stick
j. Align the replacement eUSB device over the connector and standoff. The device fits over the
threaded post that sticks up off the board and accepts a screw to hold the eUSB firmly to the Cisco
ASR 1000 RP1 board.
k. Gently insert the new eUSB device by pressing it into the connector keeping aligned with the
standoff and secure the eUSB device with the small Phillips screw as displayed in Figure 8-12.
Figure 8-12 Cisco ASR1000-RP1 eUSB Device Removal and Replacement
232373
3 2
1 Phillips screw 3 Standoff

2 eUSB connector
Step 3 Replace the Cisco ADR1000-RP into chassis.

Step 4 Restore files to bootflash and startup-config
This completes the removal and replacement of the eUSB flash device on a Cisco ASR1000-RP1.
Removing and Replacing the 1GB USB Flash Token Memory

Stick
The Cisco ASR 1000 Series Route Processor 1 contains ports for a 1GB flash token memory stick to
store configurations or Cisco IOS XE consolidated packages.
Note Only Cisco USB Flash memory modules are supported by Cisco routers.
OL-13208-03 8-15

Removing and Replacing the 1GB USB Flash Token Memory Stick
Figure 8-13 shows the USB port 0 or 1 connector (callout 4) on the Cisco ASR 1000 Series Route
Processor 1 for the 1GB flash token memory stick.
Figure 8-13 Cisco ASR 1000 Series Route Processor 1 Token Memory Stick Port
1
CRIT HD
PWR ACTV MAJ O USB 2
AC
STAT STBY MIN BF
ASR1000-RP1 0 1 DISK
3
280078
5 4
1 Internal hard drive LED 4 USB0 and USB1 connectors

2 External USB Flash LED 5 Cisco ASR1000-RP1 LEDs
3 Internal USB bootflash LED
Caution Do not remove a USB Flash memory module when issuing some file access command or a read/write
operation to the Flash memory module when it is processing. The router might reload or the USB Flash
memory module can be damaged. You can check to see if the USB activity LED on the Cisco ASR1006
or ASR1004 router RP1 front panel is flashing, prior to the removal of the USB device (does not apply
to the Cisco ASR1002 Router).
To remove and then replace a USB 1GB flash token memory stick, follow these steps:
Step 1 Pull the memory stick from the USB port.
Note The Cisco ASR 1002 Router has only one USB port.
Step 2 To replace a Cisco USB Flash memory stick, simply insert the module into the USB port 0 or 1 port as
shown in Figure 8-14. The Flash memory module can be inserted in only one way, and can be inserted
or removed regardless of whether the router is powered up or not.
Note Figure 8-12 is only a sample of how the memory stick is inserted into the port and does not
display the Cisco ASR 1000 RP1 face-plate.
8-16 OL-13208-03

Removing and Replacing the Cisco ASR 1000 Series Embedded Service Processors
Figure 8-14 Cisco ASR 1000 Series Route Processor 1 Flash Token Memory Stick
CRIT
PWR
ACTV MA
J
STAT O HD
STBY MIN AC
ASR1000-R USB
P 1
BF
0 1 DISK
280382
Note You can insert or remove the memory stick whether the router is powered on or not.
This completes the USB Flash memory installation procedure.
Removing and Replacing the Cisco ASR 1000 Series Embedded

Service Processors
The following sections describe the procedures for replacing a Cisco ASR 1000 Series Embedded
Service Processors (Cisco ASR1000-ESP5, Cisco ASR1000-ESP10, or Cisco ASR1000-ESP20) in your
system. The module also contains card handles to assist in insertion and removal of the module and
retention of the module into the chassis. The Cisco ASR 1000 Series Embedded Services Processors
have no front panel I/O connectors.
Note The Cisco ASR 1000 Series Embedded Services Processor is a field-replaceable unit in the Cisco ASR
1002 Router and the Cisco ASR 1002 Router supports only the Cisco ASR1000-ESP5 and Cisco
ASR1000-ESP10, not the Cisco ASR1000-ESP20.
Note Before beginning the procedure, verify that your system meets the minimum requirements as described
in Chapter 2, “Cisco ASR 1000 Series Routers Components.”
Removing a Cisco ASR1000-ESP

To remove the Cisco ASR1000-ESP5, Cisco ASR1000-ESP10, or Cisco ASR1000-ESP20 from the
Cisco ASR 1000 Series Routers, follow this procedure:
Step 1 Slip on the ESD-preventative wrist strap that was included in the accessory kit. Loosen the captive
screws on the Cisco ASR 1000 Series Embedded Services Processor.
OL-13208-03 8-17

Removing and Replacing the Cisco ASR 1000 Series Embedded Service Processors
Embedded Services Processor (ESP5, ESP10, ESP20) out of the chassis slot.
Note Handle the Cisco ASR1000-ESP5, Cisco ASR1000-ESP10, or Cisco ASR1000-ESP20 by the
carrier edges only; never touch the printed circuit board components or connector pins.
Step 3 Place the Cisco ASR1000-ESP5, Cisco ASR1000-ESP10, or Cisco ASR1000-ESP20 on an antistatic
surface with its printed circuit board components facing upward or in a static shielding bag.
You have completed the removal procedure for the Cisco ASR 1000 Series Embedded Services
Processor. from a Cisco ASR1000-ESP.
Replacing the Cisco ASR1000-ESP

To replace the Cisco ASR 1000 Series Embedded Services Processor in the Cisco ASR 1000 Series
Router, follow this procedure:
Step 1 Attach an ESD-preventive wrist strap between you and an unfinished chassis surface.
Step 2 Remove the new Cisco ASR1000-ESP from its static shielding bag.
Step 3 Using both hands, grasp the Cisco ASR1000-ESP by its metal carrier edges and orient the it so that its
printed circuit board components are upward.
Caution Handle the Cisco ASR1000-ESP by the carrier edges and handle only; never touch the printed circuit
board components or connector pins.
Step 4 Align the left and right edges of the Cisco ASR1000-ESP printed circuit board between the Cisco
ASR1000-ESP slot guides.
Step 5 Gently slide the Cisco ASR1000-ESP all the way into its chassis slot until you feel the connectors seat
with the router midplane.
Step 6 Seat the Cisco ASR1000-ESP in the router midplane by tightening its captive installation screws with a
number 2 Phillips or a 3/16-inch flat-blade screwdriver.
This completes the procedure for replacing the Cisco ASR1000-ESP in a Cisco ASR1000 Series Router.
8-18 OL-13208-03

Removing and Replacing a SPA Interface Processor

The Cisco ASR 1006 Router supports three SPA Interface Processors (SIPs) and the ASR 1004 Router
supports two SIPs and shared port adapters (SPAs). Online insertion and removal (OIR) is supported on
the SIPs and SPAs.
Note For detailed information about SIP and SPA software commands such as activating and deactivating
SIPs, prepare for online insertion and removal of SPAs, and activate and deactivate configuration
examples, see the Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Hardware
Installation Guide.
Note The embedded shared port adapter interface processor (SIP) on the Cisco ASR 1002 Router does not
support online insertion and removal. However, the SPAs on the Cisco embedded ASR1000-SIP10 do
support online insertion and removal.
Caution When removing or replacing SPAs, make certain that all the screw fasteners on each card and each SIP
are screwed in tightly to prevent accidental removal of another card. Each SIP has two screw fasteners
per slot and each SPA has two screw fasteners.
We suggest you have the following tools and parts readily available for installation of the SIPs and SPAs:
• Number 2 Phillips or a 3/16-inch flat-blade screwdriver
• Shared port adapter interface processor (SIP)
• Shared port adapters (SPAs)
• Cables
• Your own ESD-prevention equipment or the disposable grounding wrist strap included with all
upgrade kits, field-replaceable units (FRUs), and spares
• Antistatic mat or surface, or static shielding bag
If you need additional equipment, contact a service representative for ordering information.
Electrostatic Discharge Prevention

Electrostatic discharge (ESD) damages equipment and impairs electrical circuitry. ESD occurs when
printed circuit boards are improperly handled and results in complete or intermittent failures.
Each SPA circuit board is mounted to a metal carrier and is sensitive to electrostatic discharge (ESD)
damage. The SIP and SPAs consist of a printed circuit board that is fixed in a metal carrier.
Electromagnetic interference (EMI) shielding, connectors, and a handle are integral components of the
carrier.
When a subslot is not in use, a SPA blank filler plate must fill the empty subslot to allow the router to
conform to electromagnetic interference (EMI) emissions requirements and to allow proper airflow
across the installed modules. If you plan to install a SPA in a subslot that is not in use, you must first
remove the SPA blank filler plate.
OL-13208-03 8-19

Caution Always handle the SIP by the carrier edges and its handle; never touch the SIP components or connector
pins.
Figure 8-15 Handling the Cisco ASR 1000 Series SPA Interface Processor
Printed circuit board
70006
Metal carrier
GND
1 Printed circuit board 2 Metal carrier
Although the metal carrier helps to protect the SIP and SPA from ESD, wear a preventive antistatic strap
whenever handling the SIP and SPA. Ensure that the strap makes good skin contact and connect the
strap’s clip to an unpainted chassis surface to safely channel unwanted ESD voltages to ground.
If no wrist strap is available, ground yourself by touching the metal part of the chassis.
Following are guidelines for preventing ESD damage:
• Always use an ESD wrist strap or ankle strap when installing or replacing the Cisco ASR 1000
Series SPA Interface (SIP) and shared port adapter. Ensure that the ESD strap makes contact with
your skin.
• Handle the Cisco ASR 1000 Series SPA Interface (SIP) or shared port adapter by its metal carrier
edges and handles; avoid touching the printed circuit board or any connector pins.
• When removing an Cisco ASR 1000 Series SPA Interface (SIP) or shared port adapter, place it on
an antistatic surface with the printed circuit board components facing upward, or in a static shielding
bag. If you are returning a shared port adapter or Cisco ASR 1000 Series SPA Interface (SIP) to the
factory, immediately place it in a static shielding bag.
8-20 OL-13208-03

Removing a SPA Interface Processor

To remove a SPA Interface Processor (SIP), follow these steps.
Step 1 Slip on the ESD-preventative wrist strap that was included in the accessory kit. Loosen the captive
screws on the Cisco ASR 1000 Series SPA Interface Processor.
SPA Interface Processor out of the chassis slot.
Note Handle the Cisco ASR1000-SIP10 by the card edges only; never touch the printed circuit board
Step 3 Place the Cisco ASR1000-SIP10 on an antistatic surface with its printed circuit board components facing
upward or in a static shielding bag.
For detailed information about installing and removing SIPs and SPAs, see the Cisco ASR 1000 Series
Aggregation Services Routers SIP and SPA Hardware Installation Guide.
You have completed the removal procedure for the Cisco ASR1000-SIP10.
Replacing a SPA Interface Processor

To replace a SPA Interface Processor (SIP), follow these steps.
Step 1 Before inserting a SIP, make sure that the chassis is grounded.
Step 2 To insert the SIP, carefully align the edges of the SIP between the upper and lower edges of the router
slot.
Step 3 Carefully slide the SIP into the router slot until the SIP makes contact with the backplane.
Step 4 Tighten the locking thumbscrews on both sides of the SIP.
Step 5 Connect all cables to each SPA.
Removing a Shared Port Adapter From a SIP

To remove a shared port adapter (SPA), follow these steps.
Step 1 Attach an ESD wrist strap between you and an unpainted chassis surface.
Step 2 Shut down the interface so that there is no traffic running through the shared port adapter when it is
removed.
Caution Removing a shared port adapter while traffic is flowing through the ports can cause system disruption.
OL-13208-03 8-21

Removing and Replacing a Cisco ASR 1006 Router Power Supply
Refer to the following example to shut down the interface FastEthernet0/1/0 on the 8-Port Fast Ethernet
Shared Port Adapter (SPA-8X1FE-TX-V2).
a. At the router# prompt, type:
configure terminal and press Enter. The global configuration mode prompt Router (config)#
appears.
b. At the router (config)# prompt, type:
interface FastEthernet0/1/0 and press Enter. The interface configuration mode prompt
Router(config-if)# appears.
c. At the router (config-if)# prompt, type:
shutdown and press Enter. This disables the interface FastEthernet0/1/0.
d. At the router(config-if)# prompt, type:
end and press Enter. The privileged EXEC mode prompt Router# appears.
Step 3 Disconnect all cables from the shared port adapter.
Step 4 Unscrew the captive installation screws on either side of the SPA.
Step 5 Grasp the handles and pull the SPA from the SIP.
You have completed the removal procedure for the Cisco ASR1000 Series SPA.
Replacing a Shared Port Adapter In a SIP

To replace a shared port adapter in a SIP module, follow these steps:
Step 1 To insert the SPA in the SIP, locate the guide rails inside the SIP that hold the SPA in place. They are at
the top left and top right of the SPA slot and are recessed about an inch.
Step 2 Carefully slide the SPA all the way in the SIP until the SPA is firmly seated in the SPA interface
connector. When fully seated, the SPA might be slightly behind the SIP faceplate.
Step 3 After the SPA is properly seated, fasten the SPA in place with the captive installation screws on either
side of the SPA.
Removing and Replacing a Cisco ASR 1006 Router Power

Supply
This section provides information about removing and replacing the following power supplies in a Cisco
ASR 1006 Router:
• AC power supply
• DC power Supply
8-22 OL-13208-03

Removing the AC Power Supply from Cisco ASR 1006 Router

Because of the power supply redundancy, there is no need to power off the Cisco ASR 1006 Router
before removing one of the AC power supplies.
supply slot 1.
To remove a Cisco ASR 1006 Router AC power supply that is not operating normally (and then replace
the AC power supply within five minutes), follow this procedure:
Step 2 Before you turn off a power supply, make certain the chassis is grounded.
Step 3 Turn the power supply Standby switch to the Standby position.
Figure 8-16 AC Power Inlet and Standby Switch
1
2
100-240V
~ 16-7A
50-60HZ
This unit
migh
one powe t have more than
r su
All connec pply connection.
tions
to de-energ must be removed
ize the un
it.
280083
1 Power inlet 2 Power supply AC Standby switch
Step 4 Unplug the power cable from the AC inlet on the back of the power supply and the power source.
Step 5 Unscrew the power supply captive screws.
Note Two power supplies must be installed in the chassis at all times to ensure sufficient cooling. The
system fans are inside the power supply units and must spin for cooling. Because all the system
fans can be powered by one power supply, the second power supply unit does not have to be
powered on, but it must be installed.
Caution If you remove a power supply, the system can run for a maximum of five minutes before the system shuts
down. The fans and power elements are independent within the power supply. Therefore, it is not
required that the replacement power supply be energized within five minutes. The only requirement is
that the power supply be installed in the chassis, which energizes the fans and maintains proper system
cooling.
OL-13208-03 8-23

Step 6 Grasping the power supply handles, pull the power supply from the chassis.
Step 7 Replace the AC power supply within 5 minutes.
This completes the procedure for removing the AC power supply from the Cisco ASR1006 chassis.
Replacing the AC Power Supply in Cisco ASR 1006 Router

This section provides information about installing an AC power supply in the Cisco ASR 1006 Router.
6 7 8
OUTPUT INPUT INPUT

FAIL OK OK
ALARMS
60V
1A MAX
100-240V~ 16-7A
50-60HZ
280029
4
3 2 1

2 AC power supply DB-25 alarm connector 6 AC power inlet
3 Cable tie wrap tabs 7 AC power supply Standby switch (standby
through the top of it). A Standby switch is not
considered a disconnect.
4 AC power supply captive screws 8 AC power supply LEDs
Step 3 Insert the AC power cable.
Step 5 Turn the power supply Standby switch to the On (I) position.
8-24 OL-13208-03

This completes the procedure for installing the AC power supply in the Cisco ASR 1006 Router.
Removing and Replacing a DC Power Supply in Cisco ASR 1006 Router

This section provides information about removing and installing a DC power supply in the Cisco
ASR 1006 Router.
Statement 1046
Statement 1003
Statement 1030
Figure 8-18 shows the DC power supply and components for the Cisco ASR 1006 Router.
9 10
OUTPUT INPUT INPUT

FAIL OK OK
OFF
55
ALARMS
60V
-48/-60V 40A
1A MAX
280023
6 5 4 3 2 1
1 Fan 6 DC power supply ground studs

2 DB-25 terminal alarm connector 7 DC power supply captive screw
3 Tie-wrap tab 8 DC power supply handle
4 DC power supply terminal block and plastic 9 On/Off (|/O) circuit breaker switch
cover
5 Earth ground symbol 10 Power supply LEDs:
Statement 1003
OL-13208-03 8-25

Statement 1030
Removing the DC Power Supply from Cisco ASR 1006 Router

Before you can remove a DC power supply from the Cisco ASR 1006 Router, you must remove power
from the power supply. Follow these steps to remove power and the DC power supply from the chassis.
Caution Make certain that the chassis ground is connected before you begin removing and installing the power
supply. For the chassis ground stud location.
Step 1 Before servicing the power supply, switch the circuit breaker Off in your equipment area. As an
additional precaution, tape the circuit breaker switch in the Off position.
Step 3 Switch the power supply circuit breaker switch to Off (O).
Step 4 Locate the terminal block on the rear of the chassis on the power supply.
Figure 8-19 shows the DC power supply terminal block.
8-26 OL-13208-03

Figure 8-19 Cisco ASR 1006 Router DC Power Supply Terminal Block and Plastic Cover
1 2
OFF
55
-48/-60V
40A
This unit
might have m
ore than on
e power su
pply conn
280027
ection. Al
l connectio
ns must be
remov
4
3
1 Negative terminal 3 Plastic cover slotted area

2 Positive terminal 4 Terminal block plastic cover
Step 5 Remove the slotted plastic cover from the terminal block (Figure 8-19).
a. Loosen and remove the single screw on the plastic cover. The plastic cover has slots that help to slide
it out diagonally from the terminal block.
b. Using a nut driver (7/16 size), unsrew the positive kepnut, positive cable, and the flat washer, in that
order.
The terminal block houses two double-hole barrel lugs.
c. Follow Step 4b and remove the negative cable.
Figure 8-20 shows the DC power supply terminal block with cables connected.
OL-13208-03 8-27

Figure 8-20 Cisco ASR 1006 Router DC Power Supply Terminal Block Cable Connections
1 2
OFF
-48/-60V 40A
4
3
280024
1 Negative lead 3 Protective sleeving around the stud and cable
2 Positive lead 4 Earth ground stud and cable
Step 6 Locate the power supply ground stud (Figure 8-20). Remove the earth ground (GND) cable from the DC
power supply.
Step 7 Loosen and remove the Kepnut screw, washer, and ground lug in that order.
Warning When installing the unit, the ground connection must always be made first and disconnected last.
Step 8 Loosen the four captive screws on the DC power supply.
cooling.
8-28 OL-13208-03

Step 10 Replace the DC power supply within five minutes.
This completes the procedure of removing a DC power supply from the Cisco ASR 1006 Router.
Replacing the DC Power Supply in Cisco ASR 1006 Router
source at your site. Typically, green or green/yellow is used for ground (GND), black is used for -48V
on negative (–) terminal and red is used for RTN on the positive (+) terminal. Make certain the lead color
source.
Statement 1046
To install the DC power supply, follow these steps:
Step 1 Grasp the DC power supply by the two handles and carefully slide it into the chassis. Make sure you
align the rear connector to the backplane until it is fully seated.
Step 2 Tighten the captive screws on the power supply.
Step 3 Make certain that the chassis ground is connected before you begin installing the DC power supply.
Step 4 Locate the ground stud on the DC power supply for the GND connection which must be installed first
and follow these steps:
a. Using the grounding lug, replace the washers and Kepnut screw in the following order.
– Flat washer
– Kepnut screw
b. Tighten the Kepnut screws (use the screwdriver to tighten the ground screw to a torque of
20+/–2 in-lbs / 2 per.) on the power supply ground studs.
Step 5 Attach the other end of the ground cable to the site ground associated to the DC power supply system
that you are working on.
Step 6 Remove the plastic cover from the terminal block if it is still on.
Caution Before you continue to install the terminal block ground wires, stop and perform Step 7. This is to
prevent any contact between the metal power lugs and plastic cover.
Step 7 You must wrap the positive and negative power cables with sleeving. Take each wire and cover the area
from the lug to the wire with heavy shrink sleeving (see Figure 8-21.)
OL-13208-03 8-29

Figure 8-21 Cisco ASR 1006 Router DC Power Supply Terminal Block Ground Lugs
1 2
OFF
-48/-60V 40A
4
3
280024
1 Negative lug and wire with sleeving wrapped 3 Protective sleeving area
2 Positive lug and wire with sleeving wrapped 4 Earth ground stud and cable
Step 8 For easier cable-management, insert the positive cable first. Replace the ground lug with cable in the
following order:
a. Flat Washer
b. Ground lug with positive wire
c. Kepnut screw
Step 9 Tighten the Kepnut screw (use the screwdriver to tighten the ground screw in the terminal block to a
torque of 20+/–2 in-lbs / 2 per.) and repeat the same steps for the negative wires.
contact. Ti-wrap studs are located below the power supply terminal block.
Note The ground wire must contain a loop when securing it to the tie-wrap tab to prevent it from being
pulled out.
Step 11 Replace the terminal block plastic cover, which is slotted and keyed to fit correctly over the terminal
block; then tighten the black screw (use the screwdriver to tighten the screw to a torque of 5 in-lbs / 1
per.).
8-30 OL-13208-03

Figure 8-22 Cisco ASR 1006 Router DC Power Supply Terminal Block Plastic Cover and Switch
OFF
55
-48/-60V
40A
280026
2
1 DC power supply On/Off switch 2 Terminal block plastic cover black screw
Step 12 Remove the tape from the circuit-breaker On/Off switch.

Step 13 Switch the circuit breaker On/Off switch to the On (|) position.
Note The requirement for maximum torque applied to the power or ground Kepnuts must be 8 in-lb when the
power or ground lug is not present.
This completes the procedure for installing the DC power supply into the Cisco ASR 1006 Router.
Removing and Replacing a Cisco ASR 1004 Router Power

Supply
ASR 1004 Router:
• AC power supply
• DC power Supply

Because of the power supply redundancy, there is no need to power off the Cisco ASR 1004 Router
before removing one of the AC power supplies.
OL-13208-03 8-31

The Cisco ASR 1004 Router has two of the same type power supplies in power supply Slot 0 and power
supply Slot 1.
Figure 8-23 Cisco ASR 1004 Router AC Power Supply Slot 0 and Slot 1
1 2
OUTPUT INPUT FAN

FAIL OK OK
100V-240V~ 12A-5A
ALARMS
50-60Hz
60V
1A MAX
OUTPUT INPUT FAN

FAIL OK OK
100V-240V~ 12A-5A
ALARMS
50-60Hz
60V
1A MAX
280184
6 5 4 3

Following these steps to remove an AC power supply from the Cisco ASR 1004 Router.
Step 2 Before you turn off a power supply, make certain the chassis is grounded.
Step 3 Turn the power supply Standby switch to the Standby position.
Step 4 Unplug the power cable from the AC inlet on the back of the power supply and the power source.
Step 5 Unscrew the four power supply captive screws and grasp the handles on both sides of the power supply.
cooling.
8-32 OL-13208-03

Step 7 Replace the AC power supply within five minutes.

Step 3 Insert the AC power cable.
Step 5 Turn the power supply Standby switch to On (|) position.
This completes the procedure for installing the AC power supply in a Cisco ASR 1004 Router.
Removing and Replacing a DC Power Supply in Cisco ASR 1004

Router
ASR 1004 Router.
Statement 1046
Statement 1003
Statement 1030
OL-13208-03 8-33

1 2
OUTPUT INPUT FAN

FAIL OK OK
60V
1A MAX
OUTPUT INPUT FAN

FAIL OK OK
60V
1A MAX
280185
7 6 5 4 3
1 DC power supply terminal block and plastic 5 DC power supply earth ground symbol
cover
2 DC power supply LEDs 6 DC power supply On (I)/ Off (O)
Statement 1003
Statement 1030
8-34 OL-13208-03

Removing the DC Power Supply From Cisco ASR 1004 Router

Before you can remove a DC power supply from the Cisco ASR 1004 Router, you must remove power
from the power supply. Follow these steps to remove power and the DC power supply from the chassis.
Step 1 Make certain that the chassis ground is connected before you begin removing the DC power supply.
Step 2 Switch the power supply circuit breaker switch to Off (O).
Step 3 Locate the terminal block on the rear of the chassis on the power supply. Figure 8-24 shows the DC
power supply terminal block.
Step 4 Remove the slotted plastic cover from the terminal block.
Figure 8-25 Cisco ASR 1004 Router DC Power Supply Terminal Block
1 2 3 4
280188
1 Negative terminal 3 Earth ground stud

2 Positive terminal 4 Terminal block plastic cover screws
a. Loosen and remove the two #10 screws from the plastic cover. The plastic cover has slots that help
to slide it out towards the right.
b. Using a nut driver (7/16 size), unscrew the positive kepnut, positive cable, and the flat washer, in
that order. The terminal block houses two double-hole barrel lugs.
c. Follow Step 4b and remove the negative cable.
OL-13208-03 8-35

Figure 8-26 shows the DC power supply terminal block with lead wires connected.
Figure 8-26 Cisco ASR 1004 Router DC Power Supply Terminal Block Lead Wire Connection
280187
5 4 3
1 Ground stud and wire 4 Flat washer

Step 5 Locate the power supply ground stud (Figure 8-20). Remove the earth ground (GND) cable from the DC
power supply.
Step 6 Loosen and remove the Kepnut screw, washer, and ground lug in that order.
Warning When installing the unit, the ground connection must always be made first and disconnected last.
Step 7 Loosen the captive screws on the DC power supply.
8-36 OL-13208-03

cooling.
source at your site. Typically, green or green/yellow is used for ground (GND), black is used for negative
(–) terminal and red is used for the positive (+) terminal. Make certain the lead color coding you choose
for the DC-input power supply matches lead color coding used at the DC power source.
Statement 1046
To install the DC power supply, follow these steps:
Step 1 Make certain that the chassis ground is connected before you begin installing the DC power supply.
Step 2 Grasp the DC power supply by the two handles and carefully slide it into the chassis. Make sure you
align the rear connector to the backplane until it is fully seated.
Step 3 Tighten the captive screws on the power supply.
Step 4 Locate the power supply terminal block and remove the plastic cover from the terminal block:
a. Unscrew and remove the two #10 screws.
b. Slide the cover off the terminal block towards the right.
OL-13208-03 8-37

1 2 3 4
280188
4
1 DC power supply negative terminal 3 DC power supply earth ground terminal

2 DC power supply positive terminal 4 Terminal block plastic cover screws
Caution Before you continue to install the terminal block ground wires, stop and perform Step 5 to prevent any
contact with metal lead on the ground wire and the plastic cover.
Step 5 You must wrap the positive and negative cables with sleeving. Take each ground wire and cover the area
from the lug to the wire with heavy shrink sleeving (see Figure 8-20).
Step 6 Attach the GND wire first and follow this order:
a. Flat Washer
b. Ground lug with grounding wire
c. Kepnut screw
Step 7 Tighten the KEP-style hex nut screws (use the screwdriver to tighten the ground screw in the terminal
block to a torque of 18-22 in-lbs) on the power supply studs
Step 8 Insert the positive ground cable. Replace the ground lug with cable in the following order:
a. Flat Washer
b. Ground lug with positive wire
c. Kepnut screw
Step 9 Tighten the KEP-style hex nut screws (use the screwdriver to tighten the positive ground screw in the
terminal block to a torque of 18-22 in-lbs) on the power supply ground studs and repeat the same steps
for the negative ground stud and wire.
8-38 OL-13208-03

Figure 8-28 Cisco ASR 1004 Router DC Power Supply Terminal Block Ground Cables
280187
5 4 3
1 Ground stud and wire 4 Flat washer

contact. Tie-wrap studs are located below the power supply terminal block.
Note The ground wire must contain a loop when securing it to the tie-wrap tab to prevent it from being
pulled out.
Step 11 Replace the terminal block plastic cover and tighten the screws. The plastic cover slides in easily over
the terminal block.
Step 12 If you taped the circuit breaker, then remove the tape from the circuit-breaker switch handle and move
the circuit-breaker handle to the on position.
Step 13 Switch the power supply circuit breaker switch to the On (|) position.
OL-13208-03 8-39


ASR 1002 Router:
• AC power supply
• DC power Supply
Note You must have both power supplies installed in the Cisco ASR 1002 Router.
supply slot 1.
1 2 3 4 5 6


280288
1
8 7
1 AC power supply ESD socket 5 AC power supply fan


To remove the AC power supply from the Cisco ASR 1002 Router, follow these steps:
Step 2 Turn the switch to the Off (O) position, remove wiring, and unplug the AC cord.
Step 3 Unscrew all of the power supply captive screws.
8-40 OL-13208-03

cooling.
Step 5 Replace the AC power supply within five minutes.

To connect AC power to the Cisco ASR 1002 Router, follow these steps:
Step 1 At the rear of the router, check that the power switch is in the Off (O) position.
Note Turn the power switch to the On (I) position after both power sides of the power cord are
connected.
Step 2 Insert the AC power cable into the AC power inlet and then turn On (I).
Step 3 To ensure that the AC power cord does not interfere with other cables or wires, dress the AC power cable
in one of the following ways.
a. Leave a small service loop in the AC power cord from the inlet and then secure the power cord
through the AC power supply handle as shown in Figure 8-30. Or go to step 3b.
OL-13208-03 8-41

Figure 8-30 Cisco ASR 1002 Router AC Power Supply and Cord in Slot 1
OUTPUT
INPUT
FAN
FAIL
OK OK
This unit
might
sup
tion
rgize the d
unit.
280383
1
1 AC power cord
b. Take the power cord and run it below the handles of the power supply in slot 1and the power supply
in slot 0 (left). Make sure the power cord is hanging loosely so that it cannot be disconnected from
the AC power inlet.
Figure 8-31 Cisco ASR 1002 Router AC Power Cord Through AC Power Supply 0 and 1
OUTPUT
INPUT
FAN
FAIL
OK OK
This unit
might have
one powe more
r supply conne than
All conne ction.
ctions
the unit.
OUTPUT
INPUT
FAN
FAIL
OK OK
This unit
might have
one powe more
r supply conne than
All conne ction.
ctions
the unit.
280377
Caution Do not run the AC power cord through the either power supply handles as shown in Figure 8-32.
8-42 OL-13208-03

Figure 8-32 Cisco ASR 1002 Router Improper AC Power Cord Cabling
OUTPUT
INPUT
FAN
FAIL
OK OK
This unit
might have
one powe more
r supply conne than
All conne ction.
ctions
the unit.
OUTPUT
INPUT
FAN
FAIL
OK OK
This unit
might have
one powe more
r supply conne than
All conne ction.
ctions
the unit.
280378
Note Using a tie wrap for the AC power cable is optional and not necessary. However, if you do attach
the AC power cable to a power supply tab and then you remove the AC power cable for some
reason, check for any damage to the cable after you cut the tie wrap off. If the power cord is
damaged, replace it immediately.
cooling.
This completes the procedure for installing the AC power supply in the Cisco ASR 1002 Router.
Removing and Installing a DC Power Supply in Cisco ASR 1002 Router

ASR 1002 Router.
Statement 1046
OL-13208-03 8-43

Statement 1003
Statement 1030
1 2 3 4 5 6


280289
1
-48V/-60V 16A -48V/-60V 16A
7
10 9 8
1 DC power supply ESD socket 6 DC power supply captive installation screw

3 DC power supply switch Standby/On (I) 8 Earth ground (GND)
Statement 1003
Statement 1030
8-44 OL-13208-03

Removing the DC Power Supply from Cisco ASR 1002 Router

Before you can remove a DC power supply from the Cisco ASR 1002 Router, you must remove input
power going to the power supply.
Caution Make certain that the chassis ground is connected before you begin removing and installing the power
supply.
To remove the DC power supply from the Cisco ASR 1002 Router, follow this procedure:
Step 2 Place the power supply Standby switch in the Standby (see Figure 8-34) position.
-48V/-60V
16A
280291
1 Negative terminal 3 Earth ground terminal

2 Positive terminal 4 DC power supply Standby switch
Step 3 Turn off the branch circuit breaker before touching terminal screws. Then start loosening terminal block
screws to remove wires.
Step 4 Remove the leads from the terminal block in this order.
a. Negative lead
b. Positive lead
c. Earth ground lead
OL-13208-03 8-45

Step 5 Unscrew all of the power supply captive screws.
cooling.

The DC power supply input connector is a euro-style terminal block. Features are provide for strain
relieving the input wires from the terminal block on the front panel. The ground wire must contain a loop
when secured to prevent any strain on the wires. The connection order is negative (–), positive (+), and
GND. The recommended branch circuit breaker for the Cisco ASR 1002 Router DC power supply is
30Amp. Use an AWG #10 gauge wire on the 30Amp circuit.
This section describes how to connect the DC power supply in a Cisco ASR 1002 Router.
source at your site. Typically, green or green/yellow is used for ground. Make certain the lead color
source.
Statement 1046
Step 1 At the rear of the router, check that the power Standby switch is in the Standby position.
Step 2 Ensure that the positive and negative leads are disconnected from the site power source and the source
circuit breaker is turned off.
Step 3 Using a wire stripper, strip approximately 0.55 inch (14 mm) from the negative, positive, and ground
lead.
8-46 OL-13208-03

Step 4 Insert the stripped end of the ground lead all the way into the ground lead receptacle on the DC-input
power supply, and tighten the receptacle screw using a 3.5mm flat-blade screwdriver to a torque of 0.5
to 0.6Nm.
Figure 8-35 Cisco ASR 1002 Router DC Power Supply Terminal Block Lead Wire Connection
OUTPUT
INPUT
FAN
FAIL
OK OK
This unit
might
sup
tion
rgize the d
unit.
2
3
-48V/-60V
16A
280290
1
1 Earth ground lead wire with service loop 3 Positive lead wire
2 Negative lead wire 4 DC power supply Standby switch
Step 5 Insert the stripped end of the positive lead all the way into the positive lead receptacle and tighten the
receptacle screw using the same 3.5mm flat-blade screwdriver. Repeat this step for the negative lead.
Note Make sure the entire stripped end of each lead is inserted all the way into its receptacle. If any
exposed wire at the stripped end of a lead is visible after inserting the lead into its receptacle,
remove the lead from the receptacle, use the wire stripper to cut the stripped end of the lead, and
repeat Step 3 through Step 5.
Step 6 After tightening the receptacle screw for the ground, and leaving the extra service loop in the ground
lead, use a cable tie to secure the three leads to the power supply faceplate tie-wrap tab.
Caution When securing the ground, positive, and negative DC-input leads to the power supply faceplate, leave
extra service loop in the ground lead to ensure that the ground lead is the last lead to disconnect from
the power supply if a great deal of strain is placed on all three leads as shown in Figure 8-35.
Step 7 Turn the branch source breaker on.
OL-13208-03 8-47

Repacking the Box
Step 8 Place the power supply standby switch to the On (I) position. The power supply LEDs light when power
is supplied to the router.
Repacking the Box

If your system is damaged, you must repack it for return shipment.
To return or move the Cisco ASR 1000 series Router to a different location, follow these instructions for
repacking the system, using the original packaging material:
Step 1 Place the bottom packing material section inside the bottom of the shipping container.
Step 2 Use at least two people to place the Cisco ASR 1000 Series Router inside the container. Be sure that the
chassis is positioned correctly before you lower it inside the container.
Step 3 Place the top packing material over the top of the Cisco ASR 1000 Series Router.
Step 4 Place both accessory boxes inside the cutouts in the top section of the packing material.
Step 5 Fold the outside carton down over the top of the accessory boxes and seal with packing tape.
Step 6 Wrap two packaging straps tightly around the top and bottom of the package to hold the outside carton
and the bottom pallet.
Caution Do not use tape to hold the outside carton to the bottom pallet. Packaging straps must be used.
This completes the procedure for repacking the shipping container.
8-48 OL-13208-03

A P P E N D I X A
Cisco ASR 1000 Series Routers Specifications
This appendix provides router specifications and cable assemblies and pinouts for the cables shipped
with the Cisco ASR 1000 Series Aggregation Services Routers.
This appendix includes the following topics for each Cisco ASR 1000 Series Routers:
• Cisco ASR 1006 Router Specifications, page A-1
Cisco ASR 1006 Router Specifications

This section lists the specifications for the Cisco ASR 1006 Router.
Table A-1 lists the Cisco ASR 1006 Router physical specifications.
Table A-1 Cisco ASR 1006 Router Specifications
Midplane Connects the Cisco ASR 1000 Series RP1, ASR 1000 Series ESP, Cisco ASR 1000 Series
SPA Interface (SIP), SPAs, and power supplies together in the system
Dimensions (H x W x D) Height = 10.5 in. (25.4 cm)
Width = 17.25 in.(43.815 cm)
Depth = 22.50 in. (57.15 cm)
Weight 109.1 pounds (fully loaded chassis)
49.5 kg
Nominal operating temperature • 41° to 104° F
• 5° to 40° C
Nominal operating humidity 10% to 85%
Storage temperature • –38° to 150° F
• –40° to 70° C
Power consumption • Maximum DC: 1700W
• Maximum AC: 1600W
• Maximum (Out): 1275W
OL-13208-03 A-1

Appendix A Cisco ASR 1000 Series Routers Specifications
Cisco ASR 1006 Router Memory and Storage Options

Table A-2 lists the hardware memory and storage options supported on the Cisco ASR 1006 Router.
Table A-2 Memory and Storage Options for Cisco ASR 1006 Router
Memory Type Default Maximum System Support

RP1 2 GB DRAM 4 GBDRAM
eUSB 1 GB (Partitioned: 2x32MB for Hard disk drive 40 GB for code storage or solid-state
NVRAM and the remaining for drive 32Gb support
mass storage
Cisco ASR 1006 Router Ethernet RJ-45 Port Pinouts

The Cisco ASR 1006 Router has an RJ-45 port for the 10/100/1000 Ethernet connection. The RJ-45 port
supports IEEE 802.3ab (Gigabit Ethernet) and IEEE 802.3u (Fast Ethernet) interfaces compliant with
10BASET, 100BASETX, and 1000BASET specifications.
The RJ-45 port supports standard straight-through and crossover Category 5 UTP cables with RJ-45
connectors. Cisco does not supply Category 5 UTP cables; these cables are available commercially.
Figure A-1 shows an RJ-45 port and connector.
Figure A-1 RJ-45 Port and Connector for Cisco ASR 1006 Router
12345678
57574
1 RJ-45 connector
Cisco ASR 1006 Router MGMT Ethernet Port Pinouts

Table A-3 lists the RJ-45 port pinout for the front panel Management Ethernet port.
Table A-3 RJ-45 Management Ethernet Port Pinouts
Pin Signal Direction Description

1 TX Data+ Out Transmit Data
2 TX Data– Out Transmit Data
3 RX Data+ In Receive Data
4, 5 NC
A-2 OL-13208-03

Table A-3 RJ-45 Management Ethernet Port Pinouts (continued)

6 RX Data– In Receive Data
7,8 NC
Cisco ASR 1006 Router BITS Port Signals and Pinouts

Table A-4 lists the pinouts of the front panel Building Integrated Timing Supply (BITS) RJ45 port.
Table A-4 BITS RJ-45 Receptacle Pinouts for Cisco ASR 1006 Router

1 RX Ring Input Receive Ring
2 RX Input Receive (T1/E1)
3, 4 N/C
5 TX Ring Unused
6 TX Unused
7,8 N/C
Cisco ASR 1006 Router Console Port Signals and Pinouts

Table A-5 lists the pinouts of the dual RJ-45 ports for the front panel console and auxiliary ports.
Table A-5 Console Port Pinouts for Cisco ASR 1006 Router

1 RTS Out Request to Send (tied to pin 8, CTS)
2 DTR Out Data Terminal Ready (always On)
3 TXD Out Transmit Data
4 GND — Ring Indicator
5 GND —
6 RXD In Receive Data
7 DSR In Data Terminal Ready
8 CTS In Clear to Send (tied to pin 1, RTS)
OL-13208-03 A-3

Cisco ASR 1006 Router Auxiliary Port Signals and Pinouts

Table A-6 lists the pinouts of the dual RJ-45 ports for the auxiliary port signals.
Table A-6 Auxiliary Port Pinouts for Cisco ASR 1006 Router

1 RTS Out Request to Send
2 DTR Out Data Terminal Ready (always On)
3 TXD Out Transmit Data
4 RI — Ring Indicator
5 GND —
6 RXD In Receive Data
7 DSR/DCD In Data Set Ready/Data Carrier Detect
8 CTS In Clear to Send
Cisco ASR 1006 Router DB-25 Pinout Assignments for Alarm Relays
The alarm ports for the Cisco ASR 1006 Router (and Cisco ASR 1004 Router) power supplies reside on
the DB-25 connector on the face of the power supply. The alarm ports are relay contact closures that the
IOS environmental software controls. The environmental monitoring functions of the system can include
voltage and temperature monitoring for the router installed components and failure sensing for power
supply fan tray.
Any alarms that light the front panel LEDs on the Cisco ASR1000-RP1 causes a contact closure between
the corresponding pins within the DB-25 alarm port of both power supplies. In the DB-25 connector,
each alarm consists of a three-pin set containing a common pin, a normally open pin, and a normally
closed pin. The connections that describe alarm activity are Alarm off (Common is connected to
normally closed and normally open is disconnected) and Alarm on (Common is connected to normally
open and normally closed is disconnected).
Table A-7 lists the common, normally open, and normally closed relay contacts accessible to an external
alarm monitoring facility by means of the DB-25 connector.
Table A-7 Cisco ASR 1006 Router DB-25 Alarm Connector Pinout Assignments
Common Normally Normally

Signal Description (CM) Open (NO) Closed (NC) SPARE
CRTAA Critical Audible Alarm 2 1 14
MAJAA Major Audible Alarm 16 3 15
MINAA Minor Audible Alarm 5 4 17
CRTVA Critical Visual Alarm 19 6 18
MAJVA Major Visual Alarm 8 7 20
MINVA Minor Visual Alarm 9
SPARE SPARE—unused pin 10, 11, 12, 13
reserved for future use
A-4 OL-13208-03


Midplane Connects the Cisco ASR 1000 Series RP1, ASR 1000 Series ESP, Cisco ASR 1000 Series
SPA Interface (SIP), SPAs, and power supplies together in the system
Dimensions (H x W x D) Height = 7 in. (17.8 cm) (4RU rack-mount per EIA RS-310)
Width = 17.25 in. (43.815 cm) (19 inch rack-mount or optional 23 Telco rack- mount)
Depth = 22.50 in. (57.15 cm) (including card handles, cable-management brackets and
power supply handles)
22.6796 kg
• 5° to 40° C
• –40° to 70° C


RP1 2 GB DRAM 4 GBDRAM
eUSB 1 GB (Partitioned: 2x32MB for For mass storage: hard disk drive 40 GB or solid-state
NVRAM and the remaining for drive 32Gb support
mass storage

The Cisco ASR 1004 Router has RJ-45 port for the 10/100/1000 Ethernet connection. The RJ-45 port
OL-13208-03 A-5

connectors. Cisco does not supply Category 5 UTP cables; these cables are available commercially. See
Figure A-1 to see an RJ-45 port and connector.
Cisco ASR 1004 Router MGMT Ethernet Port Signals and Pinouts
Table A-10 RJ-45 Management Ethernet Port Pinouts for the Cisco ASR 1004 Router

1 TX Data+ Output Transmit Data
2 TX Data– Output Transmit Data
3 RX Data+ Input Receive Data
4, 5 NC
6 RX Data– Input Receive Data
7,8 NC


1 RTS Output Request to Send (tied directly to CTS)
2 DTR Output Data Terminal Ready (always On)
3 TXD Output Transmit Data
5 GND —
6 RXD Input Receive Data
7 DSR Input Unused
8 CTS Input Clear to Send (tied to RTS)
A-6 OL-13208-03



1 RTS Output Request to Send
5 GND —
7 DSR/DCD Input Data Set Ready/Data Carrier Detect
8 CTS Input Clear to Send

Table A-13 BITS RJ-45 Receptacle Pinouts for Cisco ASR 1004 Router

2 RX TIP Input Receive TIP (T1/E1)
3, 4 N/C
5 TX Ring Unused
6 TX TIP Unused
7,8 N/C
OL-13208-03 A-7

Cisco ASR 1004 Router DB-25 Pinout Assignments for Alarm Relays
Table A-14 lists the common, normally open, and normally closed relay contacts accessible to an
external alarm monitoring facility by means of the DB-25 connector.
For more information about the DB-25 alarm connector, seeCisco ASR 1006 Router DB-25 Pinout
Assignments for Alarm Relays, page A-4.
Table A-14 Cisco ASR 1004 Router DB-25 Alarm Connector Pinout Assignments
Common Normally Normally

Signal Description (CM) Open (NO) Closed (NC) SPARE
CRTAA Critical Audible Alarm 2 1 14
MAJAA Major Audible Alarm 16 3 15
MINAA Minor Audible Alarm 5 4 17
CRTVA Critical Visual Alarm 19 6 18
MAJVA Major Visual Alarm 8 7 20
MINVA Minor Visual Alarm 22 9 21
SPARE SPARE—unused pin 10, 11, 12, 13,
reserved for future use 23, 24, 25

Midplane Connects the Cisco embedded ASR1000-RP1, ASR 1000 ESP5 or ESP10, SPAs, and
power supplies together in the system
Dimensions (H x W x D) Height: 3.5 in. (8.9 cm)
Width: 17.25 in. (19-inch rack-mount or optional 23 Telco adaptor brackets)
Depth: 22.50 in. (including card handles, cable-management brackets, and power supply
handles) for mounting in a 600mm-enclosed cabinet
18.143 k
• 5° to 40° C
A-8 OL-13208-03

Table A-15 Cisco ASR 1002 Router Specifications (continued)
• –40° to 70° C


RP 1– DRAM 4 GB 4 GB – Not Field Upgradeable
FECP – DRAM 1GB for ASR1000-ESP-5 2 GB – Not Field Upgradeable
2GB for ASR1000-ESP10
eUSB – Internal Flash + NVRAM 8 GB on the built-in RP1 on the 8 GB – Not Field Upgradeable
Cisco ASR 1002 Router
(partitioned: 1 GB for
bootflash; 7 GB for mass
storage)

The Cisco ASR 1002 Router has RJ-45 port for the 10/100/1000 Ethernet connections. The RJ-45 port
connectors. Cisco does not supply Category 5 UTP cables; these cables are available commercially.
OL-13208-03 A-9

Cisco ASR 1002 Router MGMT Ethernet Port Signals and Pinouts
Table A-17 Management Ethernet 10/100/1000 RJ-45 Port Pinouts for Cisco ASR 1002 Router

1 TX Data+ Output Transmit Data
2 TX Data– Output Transmit Data
3 RX Data+ Input Receive Data
4, 5 NC
6 RX Data– Input Receive Data
7,8 NC


1 RTS Output Request to Send (tied to CTS)
5 GND —
7 DSR Input unused
8 CTS Input Clear to Send (tied to RTS)
A-10 OL-13208-03



1 RTS Output Request to Send
5 GND —
7 DSR/DCD Input Data Set Ready/Data Carrier Detect
8 CTS Input Clear to Send

Table A-20 BITS RJ-45 Interface Pinouts for Cisco ASR 1002 Router

2 RX TIP Input Receive TIP (T1/E1)
3, 4 N/C
5 TX Ring Unused
6 TX TIP Unused
7,8 N/C
OL-13208-03 A-11

A-12 OL-13208-03

A P P E N D I X B
Troubleshooting Initial Startup Problems
Your Cisco ASR 1000 Series Router went through extensive testing before leaving the factory. However,
if you encounter problems starting the router, use the information in this chapter to help isolate the cause
of the problems. This chapter contains the following sections:
• Troubleshooting Overview, page B-13
• Online Troubleshooting Resources, page B-14
• General Troubleshooting Tips, page B-14
• Troubleshooting Using a Subsystem Approach, page B-15
The procedures in this chapter assume that you are troubleshooting the initial system startup and that
your router is in the original factory configuration.
If you have removed or replaced components or changed any default settings, the recommendations in
this chapter might not apply. Make sure to review the safety warnings listed in the Regulatory
Compliance and Safety Information for the Cisco ASR 1000 Series Aggregation Services Routers
publication that accompanied your Cisco ASR 1000 Series Router before using the troubleshooting
procedures in this chapter.
Troubleshooting Overview
This section describes the methods used in troubleshooting the router. The troubleshooting methods are
organized according to the major subsystems in the router.
If you are unable to solve a problem on your own, you can contact a Cisco customer service
representative for assistance. When you call, have the following information ready:
• Date you received the router and the chassis serial number (label located on the chassis, see Serial
Number Label Location, page 1-17).
• Installed SPAs.
– Use the show platform command to determine which SPAs are installed if possible.
• Cisco software release number.
– Use the show version command to determine this information if possible.
• Brief description of the symptoms and steps you have taken to isolate and solve the issue.
• Maintenance agreement or warranty information.
OL-13208-03 B-13

Appendix B Troubleshooting Initial Startup Problems
Online Troubleshooting Resources
Online Troubleshooting Resources

In addition to following the subsystems approach to troubleshooting, a variety of online troubleshooting
resources are available.
• The Cisco ASR 1000 Series Aggregation Services Routers Troubleshooting Guide contains
information to help you troubleshoot problems with the Cisco ASR 1000 Series Router.
• Cisco.com registered users can access various troubleshooting tools such as Software Advisor,
Cisco IOS Error Message Decoder Tool, and Output Interpreter Tool from the Troubleshooting
Tools menu after logging in at http://www.cisco.com/kobayashi/support/tac/tools_trouble.shtml.
Other tools and utilities are available to registered users after logging in at
http://www.cisco.com/en/US/support/tsd_most_requested_tools.html
General Troubleshooting Tips

Read the following general troubleshooting tips you might encounter at startup.
Note You must always have two power supplies installed in the Cisco ASR 1000 Series routers to insure
sufficient cooling for the box. The system fans are inside the power supply and must spin for cooling.
Since all the system fans can be powered by one power supply, it is not required for the second power
supply to be powered on, but it must be installed.
Table B-1 General Startup Troubleshooting Tips
Symptom Corrective Action

System fails to power on Check that:
• All power cords are properly connected to the Cisco ASR 1000
Series Router and at the power connection end.
• The power switch is in the | ON position.
System fails to boot up If your system has power, check the STATUS LED on the ASR 1000
properly Series RP1and make certain all connections are secure.
Power problems If the two power supplies are both showing GREEN on their Output
LEDs, then a failure of one power supply will not result in a system
failure.
Only one operating power supply is required for a Cisco ASR 1000
series Router system to operate. Having only one supply powered is
a supported configuration. If both supplies have an OUTPUT FAIL
LED red, then the system will fail.
B-14 OL-13208-03

Troubleshooting Using a Subsystem Approach

To solve a system problem, try to isolate the problem to a specific subsystem. Compare current router
behavior with expected router behavior. Because a startup issue is usually attributable to one component,
it is most efficient to examine each subsystem, rather than trying to troubleshoot each router component.
For troubleshooting purposes in this chapter, the router consists of the following subsystems:
• Power subsystem—Includes the following components:
– AC-input or DC-input power supplies, also called power entry modules (PEMs). The Cisco ASR
1000 Series Router is shipped with fully-redundant PEMs installed in the chassis.
• Processor subsystem—The Cisco ASR1000 RP, ESPs, and SIPs all have onboard processors. The
RP downloads software to each board in the system over the Ethernet Out of Band Channel (EOBC).
There is a status LED on each board (RP1, ESP, SIP) that indicates the progress of loading software.
The LED is red if ROMMON does not boot. If the board has booted ROMMON successfully, the
LED is yellow. If operation software (IOS) has downloaded successfully, the LED is green.
• Cooling subsystem—Consists of three fans in each of the Cisco ASR 1006 Router and Cisco ASR
1004 Router power supplies and two fans in each of the Cisco ASR 1002 Router power supplies.
The fans draw in air from each of the chassis and PEMs in a front to back direction.
Normal Router Startup Sequence

You can generally determine when and where the power supply failed during the startup sequence by
checking the status LEDs on the power supply modules.
In a normal router startup sequence, the following sequence of events and conditions occur:
1. The fan in each PEM receives power and begins drawing air through the power supply. The power
supply PWR OK indicator is on and reflects power supply status.
2. As the power on and boot process progresses for the Cisco ASR 1000 Series RP1, ASR1000 ESPs,
and each installed SIP, the status of each card is indicated by LEDs.
OL-13208-03 B-15

Troubleshooting the Power Subsystem

Check the following to help isolate a problem with the power system:
Table B-2 Troubleshooting the Power System
Symptom Possible Cause Possible Solution

System begins power System has failed to boot. There is a power fault in the chassis.
on
Note that the The system status LEDs are
located on the Cisco ASR 1000 RP1 front
panel. The LEDs stay amber during the
entire IOS boot process and then turn
green when IOS has completely booted.
System does not AC power cable not fully seated at Turn the router power switch to the
power on. system or at the wall outlet (power standby position (|) and reseat the AC
source). power cable at the system or at the wall
outlet (power source).
DC power cable not turned on at the Turn the router power switch to the
panel board of the circuit breaker. standby position (|) and locate the circuit
breaker on the panel board that services
the DC circuit; switch the circuit breaker
to the on position.
AC internal power cables are not Turn the router power switch to the
fully seated from the power supply standby position (|) and remove and
reinsert the power supply cable.
System does not DC internal power cables are not Check that all ground cables are properly
power on. fully seated on the terminal block. seated in the terminal block on the DC
power supply.
Power source is faulty. Turn the power source switch off, connect
the power cable to another power source,
if available, and turn the router power
switch back on.
Faulty power cable. Turn the router power switch to the
standby position (|), (for DC power, also
turn the circuit breaker to the Off position
and tape it to that position), remove the
cable and replace it.
Faulty power supply. If the system still fails to come up when
the power supply is connected to a
different power source with a new power
cable, the power supply is probably
faulty. Contact a service representative.
B-16 OL-13208-03

Table B-2 Troubleshooting the Power System (continued)

System powers off, Power supply failure. If the system is operating with only one
no STATUS LED, power supply, it powers off after five
and no operating minutes. If this occurs, you must remove
fans. all power cables from the power supply
for at least 30 seconds before the power
supply can be powered back up.**
Contact a service representative.
** Two power supplies must be installed in the chassis at all times to ensure sufficient cooling. The system fans are inside the
power supply units and must spin for cooling. Because all the system fans can be powered by one power supply, the second
power supply unit does not have to be powered on, but it must be installed.
Caution If you remove a power supply, the system can run for a maximum of five minutes before the
system shuts down. The fans and power elements are independent within the power supply.
Therefore, it is not required that the replacement power supply be energized within five
minutes. The only requirement is that the power supply be installed in the chassis, which
energizes the fans and maintains proper system cooling.
Troubleshooting the Cooling Subsystem

Check the following to help isolate a problem with the cooling subsystem:
Table B-3 Troubleshooting the Cooling Subsystem

System shuts down, some fans may or may • One or more fans are not Contact a service
not continue to rotate, and this error operating. representative.
message is displayed: • The fans are operating too
Queued messages: slowly.
%ENVM-1-SHUTDOWN: Environmental
Monitor initiated shutdown • The power supply is not
operating.
This error message indicates that the system
To determine if the fans are
has detected an overtemperature condition
operating, listen for them. In noisy
or out-of-tolerance power condition inside
environments, place your hand on the
the chassis.
rear of the chassis to feel if air is
being forced out the vents.
Multiple fan failure Fan speed dropped below its fan fail • Identify and
speed log the failed
Red indicates failed fan status
fan PEM
Amber indicates the Cisco ASR 1000 Series location.
Route Processor 1 status
• Recommend
immediate
replacement
of PEM.
OL-13208-03 B-17

Table B-3 Troubleshooting the Cooling Subsystem (continued)

Heated exhaust air from other Move other
equipment is entering the routers equipment or the
inlet vents. router to ensure
proper airflow.
System shuts down and this error message The error message could indicate a Contact a service
is displayed: faulty component or temperature representative.
Queued messages: sensor. Before the system shuts
%ENVM-1-SHUTDOWN: Environmental down, use the show env all command
Monitor initiated shutdown to display the internal chassis
environment.
This error message indicates that the system
has detected an overtemperature condition
or out-of-tolerance power condition inside
the chassis.
Note The system fans may continue to
operate although the system shuts
down.
If an environmental shutdown results If the system still
from an out-of-tolerance power fails to come up
condition, the system shuts down. when the power
supply is
connected to a
different power
source with a new
power cable, the
power supply is
probably faulty.
Contact a service
representative.
Troubleshooting the Shared Port Adapter

Check the following to help isolate a problem with the shared port adapter:
Table B-4 Troubleshooting the Shared Port Adapter

Shared Port The shared port Reseat the adapter in its slot (you do not have to turn off the
adapter adapter might system power when removing or replacing port and service
ENABLED have pulled away adapters). After the system reinitializes the interfaces, the
LED is off. from the system ENABLED LED on the shared port adapter should go on.
board.
If the ENABLED LED remains off, the system detected a
processor hardware failure. (This LED should be on in normal
operation.) Contact a service representative for instructions.
B-18 OL-13208-03

Troubleshooting the Upgrade
Troubleshooting the Upgrade

This section contains sample error messages that appear if an upgrade fails or if an upgrade is successful
but the upgrade image is corrupted.
Replacing or Recovering a Lost Password

This section describes how to recover a lost enable or console login password, and how to replace a lost
enable secret password on your Cisco ASR 1000 Series Router.
Note It is possible to recover the enable or console login password. The enable secret password is encrypted,
however, and must be replaced with a new enable secret password.
Overview of the Password Recovery Procedure

Following is an overview of the steps in the password recovery procedure:
Step 1 If you can log in to the router, enter the show version command to determine the existing configuration
register value.
Step 2 Press the Break key to get to the bootstrap program prompt (ROM monitor). You might need to reload
the system image by power cycling the router.
Note To recover a lost password if the Break function is disabled on the router, you must have physical
access to the router.
Step 3 Change the configuration register so the following functions are enabled:
a. Break
b. Ignore startup configuration
c. Boot from flash memory
Note The key to recovering a lost password is to set the configuration register bit 6 (0x0040) so that
the startup configuration (usually in NVRAM) is ignored. This allows you to log in without
using a password and to display the startup configuration passwords.
Step 4 Power cycle the router by turning power off and then back on.
Note When powering off the router, wait 30 seconds before powering it on again.
Step 5 Log in to the router and enter the privileged EXEC mode.
Step 6 Enter the show startup-config command to display the passwords.
Step 7 Recover or replace the displayed passwords.
OL-13208-03 B-19

Step 8 Change the configuration register back to its original setting.
Details of the Password Recovery Procedure

Complete the following steps to recover or replace a lost enable, enable secret, or console login
password:
Step 1 Attach an ASCII terminal to the console port on your router.

Step 2 Configure the terminal to operate at 9600 baud, 8 data bits, no parity, and 1 stop bit (9600 8N1).
Step 3 If you can log in to the router as a nonprivileged user, enter the show version command to display the
existing configuration register value. Note the value for use later and proceed to Step 6. If you cannot
log in to the router at all, go to the next step.
Step 4 Press the Break key or send a Break from the console terminal. If Break is enabled, the router enters the
ROM monitor, indicated by the ROM monitor prompt (rommon1>). Proceed to Step 6. If Break is
disabled, power cycle the router (turn the router off or unplug the power cord, and then restore power
after waiting 30 seconds). Then proceed to Step 5.
Step 5 Within 60 seconds of restoring the power to the router, press the Break key or send a Break. This action
causes the router to enter the ROM monitor and display the ROM monitor prompt (rommon1>).
Step 6 Set the configuration register using the configuration register utility; enter the config command at the
ROM monitor prompt as follows:
rommon1> config
Step 7 Answer yes to the enable ignore system config info? question, and note the current configuration register
settings.
Step 8 Initialize the router by entering the reset command as follows:
rommon2> reset
The router initializes, the configuration register is set to 0x142, and the router boots the system image
from flash memory and enters the System Configuration Dialog prompt as follows:
--- System Configuration Dialog --
Step 9 Enter no in response to the System Configuration Dialog prompts until the following message is
displayed:
Step 10 Press Return. The user EXEC prompt is displayed as follows:

Router>
Step 11 Enter the enable command to enter privileged EXEC mode. Then enter the show startup-config
command to display the passwords in the configuration file as follows:
Router# show startup-config
B-20 OL-13208-03

Step 12 Scan the configuration file display looking for the passwords (the enable passwords are usually near the
beginning of the file, and the console login or user EXEC password is near the end). The passwords
displayed look something like this:
enable secret 5 $1$ORPP$s9syZt4uKn3SnpuLDrhuei
enable password 23skiddoo
line con 0
password onramp
The enable secret password is encrypted and cannot be recovered; it must be replaced. The enable and
console login passwords may be encrypted or clear text. Proceed to the next step to replace an enable
secret, console login, or enable password. If there is no enable secret password, note the enable and
console login passwords, if they are not encrypted, and proceed to Step 17.
Caution Do not execute the next step unless you have determined you must change or replace the enable, enable
secret, or console login passwords. Failure to follow the steps as shown might cause you to erase your
router configuration.
Step 13 Enter the configure memory command to load the startup configuration file into running memory. This
action allows you to modify or replace passwords in the configuration.
Router# configure memory
Step 14 Enter the privileged EXEC configure terminal command to enter configuration mode:
Hostname# configure terminal
Step 15 Change all three passwords using the following commands:
Hostname(config)# enable secret newpassword1
Hostname(config)# enable password newpassword2
Hostname(config)# line con 0
Hostname(config-line)# password newpassword3
Change only the passwords necessary for your configuration. You can remove individual passwords by
using the no form of the above commands. For example, entering the no enable secret command removes
the enable secret password.
Step 16 You must configure all interfaces to be not administratively shut down as follows:
OL-13208-03 B-21

Hostname(config)# interface gigabitethernet 0/0
Hostname(config-int)# no shutdown
Enter the equivalent commands for all interfaces that were originally configured. If you omit this step,
all interfaces are administratively shut down and unavailable when the router is restarted.
Step 17 Use the config-register command to set the configuration register to the original value noted in Step 3 or
Step 8, or to the factory default value 0x2102 as follows:
Hostname(config)# config-register 0x2102
Step 18 Press Ctrl-Z (hold down the Control key while you press Z) or enter end to exit configuration mode and
return to the EXEC command interpreter.
Caution Do not execute the next step unless you have changed or replaced a password. If you skipped Step 13
through Step 16, skip to Step 20. Failure to observe this caution causes you to erase your router
configuration file.
Step 19 Enter the copy running-config startup-config command to save the new configuration to NVRAM.
Step 20 Enter the reload command to reboot the router.
Step 21 Log in to the router with the new or recovered passwords.
This completes the steps for recovering or replacing a lost enable, enable secret, or console login
password.
B-22 OL-13208-03

G L OS S A RY
,
A
AAA Authentication, Authorization and Accounting. The three primary services required by a network
access server for managing subscribers.
ACL Access Control List
ACO Audible cutoff button—stops an external audible alarm
B
BBA Broadband Aggregation. This term is used to refer to the dynamic binding of subscribers to revenue
generating services.
BITS Building Integrated Timing Source
Blank filler plate An empty panel used to fill vacant subslots on a SIP. For proper operation, a SIP should be fully
installed with either functional SPAs or blank filler plates
BLT Bandwidth Limited Traffic Stream. Used in the QOS context.
BootROM Boot read-only memory.
C
CI Cluster Interconnect.
Cisco IOS XE The operating system used to run the Cisco ASR 1000 Series Routers. Cisco IOS XE is released using
consolidated packages and uses the same command-line interface as traditional Cisco IOS.
Cisco ASR1000-RP1 The Cisco ASR 1000 Series Route Processor 1 (RP1) addresses the route-processing requirements of
carrier-grade IP and Multiprotocol Label Switching (MPLS) packet infrastructures. It provides
advanced routing capabilities and also monitors and manages the other components in the Cisco ASR
1000 Series Aggregation Services Router.
Cisco The Cisco ASR 1000 Series SIP provides the physical termination for the SPAs and accepts up to four
ASR1000-SIP10 half-height and two full height Cisco SPAs, supporting Ethernet, ATM, Packet over SONET/SDH
(PoS), and Serial interfaces.
CAC Call Admission Control. This is the set of actions taken by a network during the set-up phase of a call
event to determine whether the event should be accepted or rejected.
OL-13208-03 GL-1

Glossary
Control address IP address on the SBE or DBE used for terminating the H.248 control traffic between SBE and SBE.
Cisco The Cisco ASR 1000 Series Embedded Service Processors (ASR1000-ESPs) are based on the Cisco
ASR1000-ESP5 QuantumFlow Processor for next-generation forwarding and queuing in silicon. The ASR1000-ESP5,
ASR1000-ESP10 ESP10, and ESP20 provide two centralized forwarding-engine options for the Cisco ASR 1000 Series
ASR1000-ESP20 Aggregation Services Routers.
The Cisco ASR 1000 Series ESPs are responsible for the data-plane processing tasks and all network
traffic flows through them. They are also responsible for features such as firewalls, intrusion
prevention, Network Based Application Recognition (NBAR), and Network Address Translation
(NAT).
Cisco ASR 1006 The Cisco ASR 1006 Router is a 6-rack unit (RU) chassis. It has the option of dual route processor and
Router embedded services processor support with 10Gbps throughput support. It also supports up to 12 shared
port adapters (SPAs), which makes it the highest port density solution of the three Cisco ASR 1000
Series Routers.
Cisco ASR 1004 The Cisco ASR 1004 Router is a 4-rack unit (RU) chassis that supports up to 8 shared port adapters
Router (SPAs) and comes with one route processor and one embedded services processor slot. The Cisco ASR
1004 Router provides 10 Gbps throughput support.
Cisco ASR 1002 The Cisco ASR 1002 Router is a 2-rack unit (RU) chassis that comes with an integrated route processor
Router and a serial interface processor. It houses three shared port adapter (SPA) slots supporting half height
and full height SPAs. Configurable with either the 5Gbps or 10Gbps embedded services processor and
four built-in Gigabit Ethernet ports.
Cisco QuantumFlow The forwarding processor chipset, which is on the ESP, for the Cisco ASR 1000 Series Router
Processor
consolidated A single software image containing multiple sub-packages and a provisioning file. Cisco IOS XE
package software is released using consolidated packages, and Cisco ASR 1000 Series Routers can be run using
a consolidated package or individual packages.
CPE Customer premises equipment
CTS Cisco Trusted Security. Cisco-defined protocols and procedures for user and device authentication and
role-based access control (includes packet tagging across network)
D
DBE Data border element. Represents the media-handling portion of the SBC, controlling access of media
packets to the network.
DB-25 AC power supply DB-25 alarm connector—A female DB-25 D-sub connector which enables you to
attach an external alarm monitoring facility to the router, thus supporting a telco-style of handling
alarm conditions in the router.
DCE Data communication equipment. Provide clocking to DTE. Console port of UART.
DDR Double Data Rate—Data transfer method that transfers data on both clock edges.
DES Data Encryption Standard algorithm
GL-2 OL-13208-03

Glossary
DHCP Dynamic Host Configuration Protocol
Diagnostic mode A command mode in Cisco IOS XE where all the commands stored in the non-RPIOS sub-package are
still accessible. All commands available in diagnostic mode are also available in privileged EXEC
mode.
DTE Date Terminal equipment. Auxiliary ports of a UART.
DUART Dual Asynchronous Receiver/Transmitter. Used for the CONsole serial port.
E
ESI Enhanced SerDes Interconnect—Four serial links, each at 1.25-3.125Gbps, 24b/26b. These are the
datapath links on the midplane connecting the RP, SIPs, and standby ESP modules to the active ESP.
EBFC Event-based flow control – packet-based protocol over SPA-SPI interface used by newer high-channel
count, variable rate SPA’s such as ATM to pass egress queue status deltas to the host.
EFC Extended flow control – calendar-based interface used by high-channel count SPA’s to pass egress
queue status to the host.
EMIX Typical traffic pattern including voice for a typical enterprise environment with a mix of packet sizes
and with an average packet size of 250 bytes.
EOBC Ethernet Out of Band Channel—Used for communication between the control processors on the Cisco
ASR1000 chassis
ESP Cisco ASR 1000 Series Embedded Services Processor. The ESP handles forwarding plane traffic and
performs packet processing functions such as Firewall inspection, ACLs, encryption and QoS. Note
that the Cisco ASR1000-ESP is also referred to as the ''forwarding processor'' in the document.
ESPBase ASR1000rp1-espbase.pkg. Provides the ESP operating system and control processes, and the ESP
software.
ESS This is the QFP client that provides a framework for mapping edge switching services feature data from
the control plane into QFP data plane data structures.
EV-FC Event-based flow control - interface used for chip-to-chip communication of the status of egress
queues, used on the embedded services processor
F
FECP Forwarding engine control processor. A general purpose CPU on the forwarding processor primarily
responsible for managing the forwarding engine and its connection to I/O.
FH Full height shared port adapter
FIB Cisco Forwarding Information Base
Field-replaceable Cisco component can be returned if damaged
OL-13208-03 GL-3

Glossary
FPD Field-programmable device. General term for any hardware component implemented on router cards
that supports separate software upgrades. SIPs and SPAs must have the right FPD version to function
properly; an FPD incompatibility will disable all interfaces on the SPA or all SPAs within the SIP.
FPD image package Used to upgrade FPD images. Whenever a Cisco IOS image is released that supports SPAs, a
companion SPA FPD image package is also released for that Cisco IOS software release.
FPDS Forwarding Path Data Structures
FRU Field-replaceable unit
G
GEC Gigabit Ether Channel. This is the logical aggregation of gigabit ethernet links for resiliency and load
sharing as defined in the 802.3ad protocol.
GRE Generic Route Encapsulation
H
HQF Hierarchical Queuing Framework
H.248 A VoIP signaling protocol, usually used between a dumb device and a clever controller. It is similar in
functionality to Media Gateway Control Protocol (MGCP). It is used to communicate between SBC and
DBE in a distributed SBC system.
HH Half height shared port adapters
I
IOCP IO Control Processor. General purpose CPU managing the SPA’s.
IOS Internetworking Operating System
IOSD This refers to IOS daemon running as a process under Linux on the ASR1000- RP1. IOSD is the IOS
process on IOS-SR. The bulk of the control plane, all routing protocols, configuration file management
and so on all are the domain of IOSD.
IOS-SR The Linux-based software infrastructure running on the Cisco ASR1000 series routers.
IPC Inter Process Communication. Any method of passing data between processes running in separate
address spaces.
ISSU In service software upgrade. This refers to a software upgrade when the system is in use. This allows
for two distinct versions of software running on a pair for ASR1000-RP1s while allowing for stateful
switchover between the ASR1000-RP1s.
GL-4 OL-13208-03

Glossary
L
LC Line card
LDP Label Distribution Protocol
LIPC Local IPC between two processes
Location ID A location ID is configured on each data border element (DBE). The signaling border element (SBE)
may associate endpoints with a particular location ID and then use the location IDs to route calls
between different DBEs.
M
Media address Pool of IP addresses on the DBE for media relay functionality. A pool of addresses is defined for the
Global VPN that the DBE is attached to. All vDBEs within the DBE draw media addresses from this
pool.
MGCP Media Gateway Control Protocol. This is a VoIP signaling protocol, usually used between a dumb
device and a clever controller. It is similar in functionality (if not syntax) to H.248. It is defined in RFC
2705.
MPLS Multi-Protocol Label Switching
N
NAT Network Address Translation. This is a program or piece of hardware that converts an IP address from
a private address to a public address in real time. It allows multiple users to share a single public IP
address.
NAT traversal Detects that the endpoints are behind a NAT device.
NBAR Network-based Application Recognition
OL-13208-03 GL-5

Glossary
NMI Non-maskable Interrupt
NSF Non-Stop Forwarding
O
OBFL On-board failure logging
OID Values are defined in specific MIB modules. The Event MIB allows a user or an NMS to watch over
specified objects and to set event triggers based on existence, threshold, and boolean tests. An event
occurs when a trigger is fired; this means that a specified test on an object returns a value of true. To
create a trigger, a user or an NMS configures a trigger entry in the mteTriggerTable of the Event MIB.
This trigger entry specifies the OID of the object to be watched. For each trigger entry type,
corresponding tables (existence, threshold, and boolean tables) are populated with the information
required for carrying out the test. The MIB can be configured so that when triggers are activated (fired)
either an SNMP Set is performed, a notification is sent out to the interested host, or both.
OIR Online Insertion and Removal. Feature that permits the addition, the replacement, or the removal of
cards without interrupting the system power, entering console commands, or causing other software or
interfaces to shutdown. Sometimes called hot swapping.
P
PDU Power distribution unit
PEM Power entry module
Persistent telnet A configuration that uses transport maps to manage the handling of users accessing the router via telnet.
Persistent SSH A configuration that uses transport maps to manage the handling of users accessing the router via SSH.
PID Product identifier
PLL Phase Locked Loop
POR Power-On Reset
PQ Priority queue
Provisioning file A file that manages the boot process when a Cisco ASR 1000 Series Router is configured to run using
individual packages. Provisioning files are included with the individual sub-packages in consolidated
packages, and boot statements must point to the provisioning file as the booting file when the router is
run using individual packages.
Q
QDR Quad Data Rate. Transfer method over separate read/write busses.
GL-6 OL-13208-03

Glossary
QoS Quality of Service
QFP Cisco Quantum Flow Processor. One of Cisco-developed network processors on the Cisco
ASR1000-ESPs
R
RP The Cisco ASR 1000 Series RP1, route processor. General purpose CPU responsible for routing
protocols, CLI, network management interfaces, code storage, logging, chassis management. The ASR
1000 Series RP1 processes network control packets as well as protocols not supported by the ASR 1000
Series ESP.
RPBase The sub-package responsible for providing the operating system software for the Route Processor.
sub-package
RPControl The sub-package responsible for providing the control plane processes between the IOS process and
sub-package the rest of the router.
RPACCESS The sub-package responsible for the processing of restricted components such as security features.
sub-package
RPAccess K9 ASR1000rp1-rpaccessk9.pkg. The crypto RPAccess image. This is the RPAccess sub-package in
consolidated packages that support crypto.
RPIOS sub-package The sub-package responsible for storing and running Cisco IOS features.
RU Rack Unit. A rack unit is 1.76 inches
S
SBC Cisco Session border controller. The SBC is a session-aware device which controls access to voice over
IP (VoIP) and other types of primarily media-related networks. The primary purpose of an SBC is to
protect the interior of the network from excessive call load and malicious traffic. Cisco Session Border
Controller protocol implementation performs the voice and video gateway functions simultaneously
with regular IP data services.
SBE Signaling border element. Represents the signaling agent of the SBC to handle all call processing
through SIP or H.323 protocols and in general performs the call control functions. An SBE typically
controls one or more media gateways.
Serial Link A single transmit and receive serial pair running initially at 1.25Gbits giving a payload of 1.0Gbits,
with future scalability to 3.125 Gbits giving a payload of 2.5 Gbits.
SFP Small form-factor pluggable (SFP) optical transceivers to provide network connectivity. An SFP
module is a transceiver device that mounts into the front panel to provide network connectivity.
SLA Service Level Agreement. The contract between a service provider and the customer that specifies the
level of service provided.
SIP (SBC) Session initiation protocol. VoIP signaling protocol.
OL-13208-03 GL-7

Glossary
SIP Shared port adapter interface processor. A SIP is a platform-specific carrier card that inserts into a
router slot like a line card. A SIP can hold one or more SPAs in its subslots, depending on the SIP type.
The SPA provides the network interface. The SIP provides the connection between the route processor
(RP1) and the SPA.
SIPBase The sub-package responsible for providing the SPA drivers, the SPA FPGA, and any other software
sub-package related to the SPAs.
SIPSPA The sub-package responsible for controlling the SIP operating system and control processes.
sub-package
SFP Small form-factor pluggable optical transceiver. A type of fiber optic receptacle device that mounts
flush with the front panel to provide network connectivity.
Single height Describes the dimension of a SPA that occupies a single SIP subslot or half of the SIP.
Sub-package A single software file on the Cisco ASR 1000 Series Router. Cisco IOS XE software is released using
consolidated packages, and these consolidated packages contain multiple sub-packages. Each
sub-package has a defined responsibility for running a Cisco ASR 1000 Series Router.
SPA Shared Port Adapter. A SPA is a modular, platform-independent shared port adapter that inserts into a
subslot of a compatible SIP carrier card to provide network connectivity and increased interface port
density. The SPA provides the interface between the network and the SIP.
SSD Solid state disk drive.
SSO Stateful switchover. Action of transitioning from one operational unit to another without loss of
checkpointed state.
STP Shielded twisted-pair
Subslot Secondary slot on a SIP where a SPA is installed.
T
Transport map A configuration option that can be used to provide more granularity related to users accessing a router.
Transport maps can be applied to console ports or to any users accessing a router using telnet or SSH.
GL-8 OL-13208-03

Glossary
Tracing A function on the ASR 1000 Series Routers that logs internal events. Tracing cannot be disabled on the
Cisco ASR 1000 Series Router, and all tracing logs are stored in trace files.
Trace files Files that are automatically generated on the Cisco ASR 1000 Series Router that store trace data. Trace
files are usually stored automatically in a storage directory and are often useful for customer support
purposes.
U
UDLR Uni-Directional Link Routing
UTP Unshielded twisted pair
V
VAC Volts alternating current
VDC Volts direct current
VCCV Virtual Circuit Connection Verification
vDBE Virtual DBE. Represents a resource partition within a DBE. A vDBE is a type of media gateway. Each
vDBE can be controlled by a separate SBE using the H.248 protocol.
VID Version ID
VRF Virtual Routing and Forwarding Instances
Virtual circuit Logical circuit created to ensure reliable communication between two network devices. A virtual
circuit is defined by a VPI/VCI pair, and can be either permanent (PVC) or switched (SVC). Virtual
circuits are used in Frame Relay and X.25. In ATM, a virtual circuit is called a virtual channel.
VoIP Voice over Internet Protocol. The capability to carry normal telephony-style voice over an IP-based
internet with POTS-like functionality, reliability, and voice quality. VoIP enables a router to carry voice
traffic (for example, telephone calls and faxes) over an IP network. In VoIP, the DSP segments the voice
signal into frames, which then are coupled in groups of two and stored in voice packets. These voice
packets are transported using IP in compliance with ITU-T specification H.323.
VPI Virtual path identifier. 8-bit field in the header of an ATM cell. The VPI, together with the VCI,
identifies the next destination of a cell as it passes through a series of ATM switches on its way to its
destination. ATM switches use the VPI/VCI fields to identify the next VCL that a cell needs to transit
on its way to its final destination. The function of the VPI is similar to that of the DLCI in Frame Relay.
VRRP Virtual Router Redundancy Protocol
OL-13208-03 GL-9

Glossary
GL-10 OL-13208-03

I N D EX
cable-management kit
Numerics
using 4-5, 5-6, 6-10
19-inch rack 4-14, 5-14, 6-14, 6-19 cables
1GB flash token memory stick 8-15 auxiliary port 4-20, 5-21, 6-26
connecting port adapter 4-20, 5-20, 6-25
console port 4-20, 5-21, 6-26
A
crossover 4-28, 5-29, 6-35
AC power supply Fast Ethernet Management port 4-21, 5-21
removing 8-23, 8-31, 8-40 RJ-45 pinout A-2, A-3, A-6, A-7, A-10, A-11
replacing 8-24, 8-33, 8-41 specifications A-1
airflow cautions
cautions 4-4, 5-5, 6-10 chassis overheating 1-10
chassis clearance 1-10, 3-16 chassis
exhaust 1-10 air circulation 4-4, 5-5, 6-10
monitoring 1-10 clearance 1-10
altitude 3-8 connecting to ground 4-17, 5-16, 6-23
ASR1000 Embedded Services Processor 10G Non Crypto dimensions 4-5, 5-6, 6-11
Capable 2-10 flush-mounting (19 in. rack) 4-14, 5-14, 6-19
ASR1000-ESP10-N 2-10
ground connection description 3-10
ASR1000 Series features 1-2
ground connection procedure 3-6, 3-7, 4-12, 4-18, 5-12,
audience, documentation iii-xii 5-17, 6-17, 6-23
auxiliary connector 6-26 non-rack installation 4-5, 5-6, 6-11
auxiliary port preventing overheating 3-16, 4-4, 5-5, 6-10
cables 4-20, 5-21, 6-26 rack-mounting procedures 4-8, 5-9, 6-13
Cisco ASR 1000 Series Route Processor 2-1
Cisco ASR1006
B
front panel 4-2, 5-2, 6-2
baud rate 4-20, 5-21, 6-26 LEDs 4-20, 5-21
rear view 4-2, 5-3, 6-3
specifications A-1, A-5, A-8
C Cisco Documentation DVD iii-xix
cable length, factors determining 3-12 Cisco IOS documentation iii-xix
cable lug 4-24 clearance
OL-13208-03 IN-1

Index
chassis 1-10
E
coaxial cable 3-12
commands electrical wiring requirements 3-10
show environment 1-11, 3-16 electromagnetic interference shielding 3-17
show environment table 1-13, 1-14 electromagnetic pulse
show interfaces 1-8 See EMP
show running-config 7-9 Embedded USB memory 8-13
show startup-config 7-10 EMI
configuring shielding 3-17
global parameters 7-8 EMP, avoiding 3-12
reviewing changes 7-10 Encryption services 2-10
connecting power 4-21, 5-22, 6-27 environmental monitoring and reporting
console connector 6-26 description 1-10
console port 7-8 show commands 1-11
console port cables 4-20, 5-21, 6-26 environmental monitoring error message B-18
console port kit product number A-8 error messages
console port specifications A-3, A-4, A-6, A-7, A-10, A-11 environmental shutdown B-18
ESD
prevention guidelines 3-17
D wrist strap 3-17
DCE device 4-20, 5-21 eUSB flash field-replaceable unit 8-13
DC input power 4-23 exhaust air 1-10
DC input power cable lug (figure) 4-24, 5-26

DC power
F
shutdown 1-11
DC power supply faceplate 4-2, 5-2, 6-2
removing 8-26, 8-35, 8-45 fan failures, shutdown 1-11
dimensions and weight of chassis 4-5, 5-6, 6-11 Fast Ethernet Management port 1-3
dimensions of router A-1, A-5, A-8 Fast Ethernet Management port cables 4-21, 5-21
displays Figures
environmental 1-11 DC input power cable lug 4-24, 5-26
documentation 3-22 front panel 4-2, 5-2, 6-2
audience iii-xii
related iii-xviii
G
Document Revision History iii-xi
document revision history iii-xi Gigabit Ethernet ports 1-5, 1-7, 4-2, 5-2, 6-2
global parameters, configuring 7-8
ground connection
procedure 3-6, 3-7, 4-12, 4-18, 5-12, 5-17, 6-17, 6-23
IN-2 OL-13208-03

Index
warning 3-6, 4-18, 5-17, 6-23

M
ground wire cable lug 4-24
management port, Fast Ethernet 1-3
messages
H environmental 1-11
hardware address 1-8 mode-conditioning patch cord description A-2, A-5, A-9
humidity 3-8 modem connections 4-30, 5-31, 6-36

modifications to configuration, reviewing 7-10
I
N
I/O panel 4-2, 5-2, 6-2
installation Non Crypto Capable feature 2-10
connecting port adapter cables 4-20, 5-20, 6-25 NVRAM

connecting power 4-21, 5-23, 6-28 log 1-11
grounding the chassis 3-6, 3-7, 4-12, 4-18, 5-12, 5-17, 6-17,
6-23
starting the router 7-3 O
installing online insertion and removal 2-2
general guidelines 4-4, 5-5, 6-10 out-of-tolerance voltage condition 1-10
lifting chassis 3-20 overheating
IP monitoring 1-10
router address 7-8
P
J
password
jewelry, avoiding for safety 3-2 recovering lost B-19
pinouts, RJ-45 A-2, A-3, A-6, A-7, A-10, A-11
port adapter
L
connecting cables 4-20, 5-20, 6-25
LED indicators documentation iii-xix
at startup B-15 troubleshooting B-18
LEDs 4-20, 5-21 port pinouts, Gigabit Ethernet RJ-45 A-2, A-5, A-9
LINK/ACTV (activity) 2-4 ports, Gigabit Ethernet 1-5, 1-7, 4-2, 5-2, 6-2
PWR (power) OK 2-4, 2-7, 2-12, 6-6 power
STATUS 2-4, 2-7, 2-12, 6-6 connections 4-21, 5-22, 6-27
line cards cord 3-2
making connections 5-30 surge suppression 3-12
LINK/ACTV (activity) LED 2-4 power distribution unit 4-23
OL-13208-03 IN-3

Index
power subsystem for troubleshooting B-16

S
power supply
disabled 1-11 safety guidelines
shutdown 1-11 electricity 3-18
procedures preventing electrostatic discharge damage 3-17
connecting port adapter cables 4-20, 5-20, 6-25 sample configurations
connecting power 4-21, 5-23, 6-28 global parameters 7-8
grounding the chassis 3-6, 3-7, 4-12, 4-18, 5-12, 5-17, 6-17, shielded cables 6-26
6-23 shielded Ethernet cable 6-27
replacing or recovering a lost password B-19 show commands
starting the router 7-3 show environment 1-11
processor show environment table 1-13, 1-14
shutdown 1-11 show interfaces 1-8
product disposal 3-4 show running-config 7-9
PWR (power) OK LED 2-4, 2-7, 2-12, 6-6 show startup-config 7-10
show environment command 3-16
shutdown
R
power supply 1-11
rack-mounting processor 1-11
front mounted 4-9, 4-11, 5-10, 5-11, 5-14, 5-16, 5-20, 6-15, site requirements
6-16, 6-19, 6-20, 6-22
rack mounting 3-15
verifying rack dimensions 4-8, 5-9, 6-14
slot/port numbers for interfaces 1-8
related documentation iii-xviii
specifications
remove Cisco ASR1000-ESPs 8-17
console port A-3, A-4, A-6, A-7, A-10, A-11
remove Cisco ASR1000-RP1 8-2
dimensions A-1, A-5, A-8
removing a DC power supply 8-26, 8-35, 8-45
Gigabit Ethernet RJ-45 port pinouts A-2, A-5, A-9
removing an AC power supply 8-23, 8-31, 8-40
processor and memory A-2, A-5, A-9
replace Cisco ASR1000-ESPs 8-18
startup
replace Cisco ASR1000-RP1 8-2
system 7-3
replacing an AC power supply 8-24, 8-33, 8-41
status
replacing or recovering a lost password B-19
interfaces 1-8
reviewing changes to configuration 7-10
STATUS LED 2-4, 2-7, 2-12, 6-6
RJ-45, cable A-2, A-3, A-6, A-7, A-10, A-11
subsystems for troubleshooting
RJ-45 connectors 3-13
power B-16
ROMmon (rom-monitor) upgrades B-19
system management functions 1-3
RS-232 asynchronous data 3-13
temperature 3-8
IN-4 OL-13208-03

Index
terminal server connections 7-8

troubleshooting
Cisco ASR1000 Series Troubleshooting
Module iii-xviii
port adapter B-18
power subsystem B-16
ROMmon upgrades B-19
verifying the equipment rack dimensions 4-8, 5-9, 6-14

voltage 3-8
monitoring 1-10
warning
chassis grounding 4-24, 5-26, 6-33, 8-29, 8-37, 8-46
definition 3-4, 4-3, 5-1, 5-4, 6-10
equipment installation iii-xviii, 8-1
ground connection 3-6, 4-18, 5-17, 6-23
ground connection order 3-6
installation instructions 3-4
product disposal 3-4
qualified personnel 3-5
removing power from DC circuit 3-6, 8-25, 8-34, 8-44
safety information 4-4, 5-1, 5-5, 6-10
servicing equipment 8-26, 8-34, 8-44
trained personnel 8-1
two-person lifting 4-6, 5-7, 6-12
work during lightening activity 3-19
wrist strap 8-1, 8-3
OL-13208-03 IN-5

Index
IN-6 OL-13208-03

ASR 1000 Series

Uploaded by

Copyright:

Available Formats

ASR 1000 Series

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ASR 1000 Series

Uploaded by

Copyright:

Available Formats

Cisco ASR 1000 Series Aggregation

Services Routers Hardware Installation

Text Part Number: OL-13208-03

More user manuals on ManualsBase.com

• Turn the television or radio antenna until the interference stops.

• Move the equipment farther away from the television or radio.

More user manuals on ManualsBase.com

Document Revision History xi

Document Objectives xii

Document Organization xii

Safety Warnings and Cautions xiii

Obtaining Documentation and Submitting a Service Request xix

CHAPTER 1 Cisco ASR 1000 Series Routers Hardware Overview 1-1

Cisco ASR 1000 Series Routers 1-2

Cisco ASR 1000 Series Routers Features 1-2

Cisco ASR 1000 Series Routers Configurations 1-3

Field-Replaceable Units 1-4

Functional Overview 1-4

CHAPTER 2 Cisco ASR 1000 Series Routers Components 2-1

Cisco ASR 1000 Series Route Processor 2-1

More user manuals on ManualsBase.com

How the Cisco ASR1000-RP1 Alarm LEDs Work 2-5

Cisco ASR 1000 Series Embedded Services Processors 2-9

Cisco ASR 1000 Series SPA Interface Processor 2-13

Shared Port Adapters 2-14

Cisco ASR 1000 Series Router Power Supplies 2-16

CHAPTER 3 Preparing Your Site for Installation 3-1

Safety Recommendations 3-2

Safety Warnings 3-2

Compliance Requirements 3-2

Cautions and Regulatory Compliance Statements for NEBS 3-3

Standard Warning Statements 3-4

More user manuals on ManualsBase.com

Rack-Mounting and Location Guidelines 3-14

Electrical Safety 3-18

Receiving a Cisco ASR 1000 Series Router 3-19

Chassis-Lifting Guidelines 3-20

Tools and Equipment 3-21

Cisco ASR 1000 Series Router Installation Checklist 3-23

CHAPTER 4 Cisco ASR 1006 Router Overview and Installation 4-1

Cisco ASR 1006 Router Description 4-1

General Rack Installation Guidelines 4-4

Guidelines for an Equipment Shelf or Tabletop Installation 4-5

Equipment Shelf or Tabletop Installation 4-6

Rack-Mounting a Cisco ASR 1006 Router 4-8

Attaching a Chassis Ground Connection 4-17

Connecting Console and Auxiliary Port Cables 4-20

Connecting Power to Cisco ASR 1006 Router 4-21

More user manuals on ManualsBase.com

Connecting AC-Input Power to Cisco ASR 1006 Router 4-22

Connecting System Cables 4-29

Auxiliary Connection 4-30

CHAPTER 5 Cisco ASR 1004 Router Overview and Installation 5-1

Cisco ASR 1004 Router Description 5-1

General Rack Installation Guidelines 5-5

Guidelines for an Equipment Shelf or Tabletop Installation 5-6

Equipment Shelf or Tabletop Installation 5-7

Rack-Mounting a Cisco ASR 1004 Router 5-9

Connecting Shared Port Adapter Cables 5-20

Connecting Power to Cisco ASR 1004 Router 5-22