ASR903 HW Install

Cisco ASR 903 Router Hardware
Installation Guide
March 2016
Cisco Systems, Inc.

www.cisco.com
Cisco has more than 200 offices worldwide.
Addresses, phone numbers, and fax numbers
are listed on the Cisco website at
www.cisco.com/go/offices.
Text Part Number: OL-25178-08
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL
STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.
THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT
SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE
OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.
NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED AS IS WITH
ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT
LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF
DEALING, USAGE, OR TRADE PRACTICE.
IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,
WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO
OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this
URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership
relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual addresses and phone numbers. Any examples, command display
output, network topology diagrams, and other figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses or phone numbers in
illustrative content is unintentional and coincidental.
Cisco ASR 903 Router Hardware Installation Guide
2012-2016 Cisco Systems, Inc. All rights reserved.
CONTENTS
About this Book
ix
Document Revision History

Document Audience
ix
Document Organization
Document Conventions
Obtaining Documentation and Submitting a Service Request
CHAPTER
Cisco ASR 903 router Overview
xi
1-1
Cisco ASR 903 router Features 1-1

System Specifications 1-2
Power Supply Features 1-3
Redundancy 1-4
Dying Gasp 1-4
Status LEDs 1-4
DC Power Specifications 1-4
AC Power Specifications 1-6
Fan Tray 1-6
Fan Tray (A903-FAN) 1-7
Fan Tray (A903-FAN-E) 1-7
Air Plenum 1-8
RSP Modules 1-9
Supported RSPs 1-9
Supported RSP Features 1-10
RSP Redundancy 1-10
Network Timing Interfaces 1-10
RSP Interfaces 1-10
Interface Modules 1-11
Gigabit Ethernet SFP Interface Module 1-12
Gigabit Ethernet RJ45 Interface Module 1-13
10 Gigabit Ethernet XFP Interface Module 1-14
T1/E1 Interface Module 1-16
OC-3 Interface Module 1-16
Serial Interface Module 1-17
Temperature Sensor 1-20

OL-25178-07
iii
Contents
Serial Number Label Location

Interface Numbering
CHAPTER
1-20
1-20
Regulatory Compliance
1-21
Preparing for Installation
2-1
Safety Guidelines 2-1

Standard Warning Statements 2-2
Safety Guidelines for Personal Safety and Equipment Protection
Safety Precautions for Module Installation and Removal 2-3
Safety with Electricity 2-4
Power Supply Considerations 2-8
Preventing ESD Damage 2-8
Site Planning 2-9
General Precautions 2-9
Site Planning Checklist 2-9
Site Selection Guidelines 2-10
Environmental Requirements 2-10
Physical Characteristics 2-10
Air Flow Guidelines 2-11
Air Flow Guidelines for Enclosed Rack Installation
Floor Loading Considerations 2-12
Site Power Guidelines 2-12
Electrical Circuit Requirements 2-13
Site Cabling Guidelines 2-13
Asynchronous Terminal Connections 2-14
Interference Considerations 2-14
Rack-Mounting Guidelines 2-15
Precautions for Rack-Mounting 2-15
Rack Selection Guidelines 2-15
Equipment Rack Guidelines 2-16
Installation Checklist 2-18
Creating a Site Log 2-19
Receiving the Cisco ASR 903 Router 2-19
Chassis-Lifting Guidelines 2-20
Tools and Equipment 2-20
Unpacking and Verifying the Shipped Contents
CHAPTER
Installing the Cisco ASR 903 Router

Prerequisites
2-3
2-12
2-21
3-1
3-1
iv
OL-25178-07
Contents
Installing the Router in a Rack 3-1

Installing the Chassis Brackets 3-2
Installing the Router Chassis in the Rack 3-3
Installing the Chassis in the Air Plenum 3-4
Attaching the Cable Management Brackets 3-5
Installing the Chassis Ground Connection
Installing the Fan Tray 3-10
Installing the Dust Filter 3-10
Removing the Dust Filter 3-11
Removing and Replacing the Fan Tray
3-7
3-11
RSP Installation 3-13

Installing an RSP Module 3-14
Removing an RSP Module 3-15
Hot-Swapping an RSP Module 3-16
Interface Module Installation 3-17
Installing an Interface Module 3-17
Removing an Interface Module 3-18
Hot-Swapping an Interface Module 3-18
Installing the Power Supply 3-19
Preventing Power Loss 3-20
Power Connection Guidelines 3-20
Guidelines for DC-Powered Systems 3-20
Guidelines for AC-Powered Systems 3-21
Installing the DC Power Supply 3-21
Installing the DC Power Supply Module 3-21
Installing Terminal Block on the DC PEM Unit (A900-PWR550-D) 3-22
Installing Terminal Block Connector on the DC PEM Unit (A900-PWR550-D-E)
Activating the DC Power Supply 3-26
Removing and Replacing the DC Power Supply 3-26
Installing the AC power Supply 3-27
Installing the AC Power Supply Module 3-28
Activating the AC Power Supply 3-28
Removing and Replacing the AC Power Supply 3-29
3-25
Connecting the Cisco ASR 903 Router to the Network 3-30

Connecting Console Cables 3-30
Connecting to the Serial Port using Microsoft Windows 3-31
Connecting to the Console Port using Mac OS X 3-33
Connecting to the Console Port using Linux 3-33
Installing the Cisco Microsoft Windows USB Device Driver 3-34
OL-25178-07
Contents
Uninstalling the Cisco Microsoft Windows USB Driver

Connecting to the Auxiliary Port 3-36
Connecting a Management Ethernet Cable 3-38
Installing and Removing SFP and XFP Modules 3-38
Connecting a USB Flash Device 3-38
Removing a USB Flash Device 3-39
Connecting Timing Cables 3-39
Connecting Cables to the BITS Interface 3-39
Connecting Cables to a GPS Interface 3-41
Connecting Ethernet Cables 3-42
Connecting Cables to SFP Modules 3-43
Connecting T1/E1 cables 3-43
Installing the Cable Connector 3-43
RJ45 Cable Pinouts 3-44
Connecting Cables to the Patch Panel 3-44
Recommended Patch Panel 3-45
Connecting Serial Cables 3-45
Connecting the Fan Tray Alarm Port 3-47
Connector and Cable Specifications 3-47
CHAPTER
Cisco ASR 903 Router Initial Configuration
3-35
4-1
Checking Conditions Prior to System Startup
4-1
Powering Up the Cisco ASR 903 Router 4-2

Verifying the Front Panel LEDs 4-5
Verifying the Hardware Configuration 4-5
Checking Hardware and Software Compatibility
4-5
Configuring the Cisco ASR 903 Router at Startup 4-5

Using the Console Interface 4-6
Configuring Global Parameters 4-6
Checking the Running Configuration Settings 4-7
Saving the Running Configuration to NVRAM 4-7
Safely Powering Off the Cisco ASR 903 Router
CHAPTER
Troubleshooting
4-8
5-1
Pinouts 5-1
BITS Port Pinout 5-1
GPS Port Pinout 5-2
Time of Day Port Pinout
Alarm Port Pinout 5-3
5-2
vi
OL-25178-07
Contents
Console/Aux RJ45 RS232 Serial Port Pinout

T1/E1 Port Pinout 5-4
Serial Cable Pinouts 5-5
Management Ethernet Port Pinout 5-7
USB Console Port Pinout 5-7
USB Flash/MEM Port Pinout 5-7
Fiber-Optic Specifications 5-8
5-3
LED Summary 5-8

RSP LEDs 5-8
Interface Module LEDs 5-9
OC-3 Interface Module LEDs 5-10
T1/E1 Interface Module LEDs 5-11
Serial Interface Module LEDs 5-11
Power Supply LEDs 5-12
Fan Tray LEDs 5-13
Alarm Conditions 5-13
CHAPTER
Site Log and Manufactures

Manufactures
A-1
A-3
INDEX

OL-25178-07
vii
Contents
viii
OL-25178-07
About this Book

The preface describes the revision history, audience, organization, and conventions of Cisco ASR 903
Router Hardware Installation Guide. It also lists sources for obtaining additional information and
technical assistance from Cisco Systems.
Document Revision History, page ix
Document Audience, page x
Document Organization, page x
Document Conventions, page x
Obtaining Documentation and Submitting a Service Request, page xii
Document Revision History

The following table lists the major changes made to this document for each release.
Revision
Date
Change Summary
April 2013
Added dust cap information. Added supported patch

panel information. Updated warning statements.
OL-25178-08
March 2016
Added A900 RSP3-200 module and supported

interfaces. Added information on blank deflector.
Updated the ambient temperature for the RSP3
module.
OL-25178-07
August 2015
Added A900 RSP3 module supported interface

modules. Added 1200 W power supply information.
OL-25178-07
30 November 2014
Added 32 T1/E1 interface module.
OL-25178-06
30 July 2014
Added A900 RSP2 and supported interface modules.
OL-25178-05
19 November 2013
Updated fan tray, power supply connector, dust filter,

air plenum.
OL-25178-04
30 July 2013
Updated supported SFPs for IOS XE Release 3.10S.
OL-25178-04
3 June 2013
Updated supported SFPs for IOS XE Release 3.9(1).
OL-25178-03
3 April 2013
Updated supported SFPs for IOS XE Release 3.9.
OL-25178-03
29 November 2012

OL-25178-08
-ix
Chapter
Revision
Date
Change Summary
OL-25178-03
23 August 2012
Added material for AC power supply, chassis air flow

information, and NEBS certification.
OL-25178-02
30 March 2012
OL-25178-02
24 February 2012
Added power draw and installation torque values.
OL-25178-01
16 December 2011
First release published.
Document Audience
This guide is intended for users who are responsible for installing the Cisco ASR 903 Series Aggregation
Services Router. It is intended for users who may not be familiar with the initial configuration and
troubleshooting tasks, the relationship among tasks, or the Cisco IOS software commands necessary to
perform particular tasks.
Document Organization
This guide includes the following chapters and appendix:
Title
Description
Chapter 1, Cisco ASR 903 Router

Overview
This chapter provides an overview of the

Cisco ASR 903 Router.
Chapter 2, Preparing for

Installation
This chapter provides site preparation guidelines

for installing the Cisco ASR 903 Router.
Chapter 3, Installing the Cisco ASR This chapter describes the Cisco ASR 903 Router
903 Router
and how to install it.
Chapter 5, Cisco ASR 903 Router
Initial Configuration
This chapter describes how to start the

Cisco ASR 903 Router and create an initial
system configuration.
Chapter 4, Troubleshooting
This chapter provides LED and pinout

information for troubleshooting purposes.
Appendix A, Site Log and

Manufactures
This provides a site log for tracking the

installation and maintenance activities of the
router.
Document Conventions
This document uses the following conventions:
Convention
Indication
bold font
Commands and keywords and user-entered text appear in bold font.
italic font
Document titles, new or emphasized terms, and arguments for which you supply
values are in italic font.
[ ]
Elements in square brackets are optional.
-x
OL-25178-08
Chapter
{x | y | z }
Required alternative keywords are grouped in braces and separated by

vertical bars.
[x|y|z]
Optional alternative keywords are grouped in brackets and separated by

vertical bars.
string
A nonquoted set of characters. Do not use quotation marks around the string or
the string will include the quotation marks.
courier
font
Terminal sessions and information the system displays appear in courier font.
< >
Nonprinting characters such as passwords are in angle brackets.
[ ]
Default responses to system prompts are in square brackets.
!, #
An exclamation point (!) or a pound sign (#) at the beginning of a line of code
indicates a comment line.
Note
Means reader take note.
Tip
Means the following information will help you solve a problem.
Caution
Timesaver
Means reader be careful. In this situation, you might perform an action that could result in equipment
damage or loss of data.
Means the described action saves time. You can save time by performing the action described in
the paragraph.
Warning
Means reader be warned. In this situation, you might perform an action that could result in
bodily injury.
Warning
IMPORTANT SAFETY INSTRUCTIONS. This warning symbol means danger. You are in a situation that
could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with
cal circuitry and be familiar with standard practices for preventing accidents. Use the statement
number provided at the end of each warning statement to locate its translation in the translated safety
warnings that accompanied this device. Note: SAVE THESE INSTRUCTIONS Note: This documentation
is to be used in conjunction with the specific product installation guide that shipped with the product.
Please refer to the Installation Guide, Configuration Guide, or other enclosed additional
documentation for further details. Statement 1071

OL-25178-08
-xi
Chapter
Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional
information, see the monthly Whats New in Cisco Product Documentation, which also lists all new and
revised Cisco technical documentation, at:
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html
Subscribe to the Whats New in Cisco Product Documentation as an RSS feed and set content to be
delivered directly to your desktop using a reader application. The RSS feeds are a free service. Cisco currently
supports RSS Version 2.0.
-xii
OL-25178-08
CH A P T E R
Cisco ASR 903 Router Overview

The Cisco ASR 903 Router is a fully-featured aggregation platform designed for the cost-effective
delivery of converged mobile and business services. With shallow depth, low power consumption, and
an extended temperature range, this compact 3-rack-unit (RU) router provides high service scale, full
redundancy, and flexible hardware configuration.
The Cisco ASR 903 Router expands the Cisco service provider product portfolio by providing a rich and
scalable feature set of Layer 2 VPN (L2VPN) and Layer 3 VPN (L3VPN) services in a compact package.
It also supports a variety of software features, including Carrier Ethernet features, Timing over Packet,
and pseudowire.
The Cisco ASR 903 Router is positioned as a pre-aggregation router in IP RAN (GSM, UMTS, iMAX,
CDMA, and LTE) networks or an aggregation router in Carrier Ethernet networks.
Cisco ASR 903 Router Features

The Cisco ASR 903 Router has the following hardware features:
3-RU modular chassis designed for installation in a 300 mm European Telecommunications

Standards Institute (ETSI) cabinet
Dedicated slots in the chassis that support the following:

Up to six interface modules
Up to two Route Switch Processors (RSP)
Up to two AC or DC power supply units
One fan tray
Network frequency, phase, and time inputs and outputs for network interfaces (SyncE and TDM),
BITS, 1 PPS or 10 MHz and Timing over Packet (IEEE 1588-2008)
Adjustable front and rear rail mounting locations
Front panel access to power supplies, fan tray, RSPs, and interface modules
Online insertion and removal (OIR) of RSP, interface modules, power supplies, and fan tray
Discrete status LEDs on power supply, interface module, RSP, and fan tray units
Four alarm dry contact inputs (either normally open or normally closed)
Environmental monitoring and reporting functions
LED indicators for critical, major, and minor alarms

OL-25178-08
1-1
Chapter 1
Side-to-side forced air cooling
Temperature range, see Cisco ASR 900 Series Aggregation Services Routers Data Sheet
Figure 1-1 illustrates the Cisco ASR 903 Router chassis design.
Figure 1-1
Cisco ASR 903 Router Chassis Design
GE-0
GE-1
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
PWR
FAN TEMP
STAT
GE-0
GE-1
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
GE-0
GE-1
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
CRIT MAJ MIN
PWR
STAT
PWR
STAT
SYNC
ACT
PWR
MEM
CONSOLE
1PPS
IN
1PPS
OUT
1OMHZ
IN
1OMHZ
OUT
PWR
TOD
STAT
L
7 S
7 S
7 S
BITS
MGMT
ENET
STAT
24V60V
28A
PWR
PWR
STAT
INPUT
OK
OUTPUT
FAIL
24V60V
INPUT
OK
OUTPUT
FAIL
28A
ALARM
281927
STAT
4
1
Interface modules
RSP unit
Fan tray
Redundant power units (two DC power units are shown)
Power Supply Features

The Cisco ASR 903 Router support AC and DC power supplies. For more information about installing
the Cisco ASR 903 Router power supplies, see the Installing the Power Supply, page 3-22 section.
To estimate the required power supply, use the Cisco Power Calculator.
The power sections provide more information about the power supply:
Redundancy, page 1-3
Dying Gasp, page 1-3
Status LEDs, page 1-3
DC Power Specifications, page 1-3
AC Power Specifications, page 1-6
1-2
OL-25178-08
Chapter 1

Redundancy
The Cisco ASR 903 Router chassis includes a slot for an optional redundant power supply. The
redundant power supply option provides a second power supply to ensure that power to the chassis
continues uninterrupted if one power supply fails or input power on one line fails. Redundancy is
supported either with identical power supplies or a combination of AC and DC power supply. The
Cisco ASR 903 Router supports current sharing between the power supplies.
A redundant power supply on the Cisco ASR 903 Router is recommended. Each power supply should be
connected to separate independent power sources to ensure that the router maintains power in the event
of a power interruption caused by an electrical failure, a wiring fault, or a tripped circuit breaker.
Caution
To comply with IEC 61850-3 (voltage interruptions), redundant power supplies with separately derived
power feeds are required.
Dying Gasp
The Cisco ASR 903 Router DC power supply supports the Dying Gasp feature, which allows the router
to provide an input power loss notification to the RSP so that the RSP can send appropriate SNMP traps
or OAM messages and update log files on the router. With the DC power supply, the router supports a
minimum input power loss detection time of 2 milliseconds (DC) and continued operation of at least 6
milliseconds (DC) after the notification.
Note
Continued DC power supply operation may vary for voltages other than +24/-48V.
Note
Dying Gasp is not supported on the ASR 900 RSP3 module for 1200W DC power supply.
Status LEDs
LEDs are also provided on each power supply to indicate the status of the input power and the health of
the power supply. For more information about the LEDs on the Cisco ASR 903 Router, see Chapter 4,
Troubleshooting.
DC Power Specifications
The power supply is field replaceable, hot-swappable, and operates separately from the fan tray. The
power supply contains a front panel with mounting screws, a handle for insertion and removal, and two
status LEDs. No ON/OFF switch is provided.
The DC PSU models supported on the router are:
A900-PWR550-DProvides 550 W output power for system 12 V power. Uses a euro-style

three-position terminal block connector, Figure 1-2
A900-PWR550-D-EProvides 550 W output power for system 12 V power. Uses a T-shaped

connector, Figure 1-3

OL-25178-08
1-3
Chapter 1
The A900-PWR550-D and the A900-PWR550-E power supply can be used with the
A900-RSP3C-400-S RSP modules only if the power consumption is within 550 W. However,
A900-PWR1200-D is recommended.
A900-PWR1200-DProvides 975 W output power for system 12 V power with the A903-FAN
module. As most of the system configurations using A900-RSP3C-400-S RSP modules require
power exceeding 550 W, we recommend using the A900-PWR1200-D power supply with
A900-RSP3C-400-S RSP modules. Figure 1-4.
Figure 1-2
DC PSU Module (A900-PWR550-D) with Euro-style Connector
INPUT
OK
OUTPUT
FAIL
24V60V
28A
361028
Note
Euro-style connector
Figure 1-3
DC PSU Module (A900-PWR550-D-E) with T-Shaped Connector
360882
T-shaped connector
1-4
OL-25178-08
Chapter 1

Table 1-1
DC Power Supply Specifications (550 W)
Part numbers
A900-PWR550-D, A900-PWR550-D-E
Input power specification
+24V/-48V or -60V VDC
Minimum input voltage
19.2 VDC
Maximum input voltage
72 VDC
Output voltage
+12 VDC
Wire gauge for DC input power connections
12 AWG minimum for -48/-60 VDC.

8 AWG minimum for 24 VDC.
Connector accepts 8 AWG maximum.
Maximum power output

Figure 1-4
550 W
DC PSU Module (A900-PWR1200-D)
365289
Label
Component
T-shaped connector

OL-25178-08
1-5
Chapter 1
Table 1-2
DC Power Supply Specifications (A900-PWR1200-D)
Part numbers
A900-PWR1200-D
48V, GRD, -48V
-40.8 VDC
-72 VDC
Output voltage
+12 VDC
Wire gauge for DC input power connections
8 AWG minimum for -48/-60 VDC.

Connector accepts 8 AWG maximum.
1200 W
975W with A902-FAN-E
AC Power Specifications
The AC PSU models supported on the router are:
A900-PWR550-AProvides 550 W output power for system 12 V power. Uses an IEC 320 C14
type 15 Amp power receptacle connector,
385112
The A900-PWR550-A power supply can be used with the A900-RSP3C-400-S RSP modules only
if the power consumption is within 550 W. However, A900-PWR1200-A is recommended.
1-6
OL-25178-08
Chapter 1

Table 1-3
AC Power Supply Specifications (A900-PWR550-A)
Part number
A900-PWR550-A
115VAC/ 230VAC
Input voltage
85/264 VAC
85 VAC
264 VAC
Minimum output voltage
12V
Maximum output voltage
12.4V
550 W
A900-PWR1200-AProvides 975 W output power for system 12 V power with the A903-FAN
module. As most of the system configurations using A900-RSP3C-400-S RSP modules require
power exceeding 550 W, we recommend using the A900-PWR1200-A power supply with
A900-RSP3C-400-S RSP modules. See Figure 1-5.
AC Power Supply (A900-PWR1200-A)
365292
Figure 1-5
Table 1-4
AC Power Supply Specifications (A900-PWR1200-A)
Part number
A900-PWR1200-A
115VAC/ 230VAC
Input voltage
85/264 VAC
85 VAC
264 VAC
Minimum output voltage
12V
Maximum output voltage
12.4V
1200 W

OL-25178-08
1-7
Chapter 1
Fan Tray
The fan tray has the following hardware features:
It provides side-to-side forced air cooling
It provides redundant fans
It is field replaceable
It contains status LEDs
It contains an alarm port with four external alarm inputs
The fan tray modules supported on the router are:
A903-FAN, Figure 1-6
A903-FAN-E, Figure 1-7
For more information about air flow guidelines, see Air Flow Guidelines, page 2-13. For instructions on
how to install the fan tray, see Installing the Fan Tray, page 3-11. For a summary of the LEDs on the fan
tray, see LED Summary section on page 4-13
Fan Tray (A903-FAN)

The Cisco ASR 903 Router uses a modular fan tray that is separate from the power supply. The fan tray
contains twelve fans and provides sufficient capacity to maintain operation indefinitely in the event of
an individual fan failure.
Figure 1-6
Cisco ASR 903 Router Fan Tray (A903-FAN)
FAN TEMP
CRIT MAJ MIN
281933
ALARM
1-8
OL-25178-08
Chapter 1

Fan Tray (A903-FAN-E)

The A903-FAN-E is a fan tray containing twelve (40 x 40 x 20 mm) fans and provides sufficient capacity
to maintain operation indefinitely in the event of an individual fan failure. It has a 8 mm fan dust filter
that prevents dust from entering the unit and avoids possible damage to the components. The fan tray is
IEC60950-1 compliant.
Figure 1-7
Cisco ASR 903 Fan Tray with Dust Filter and Dummy Cover (A903-FAN-E)
LEDs
Dummy cover
Alarm
Pull tab
Dust filter
360555
Dust Filter (A903-FAN-F)

The dust filter (see Figure 1-7) on the fan tray is a quadrafoam 45PPI filter which is 85 percent dust
resistant. A dummy cover (A903-FAN-F-B) secures the dust filter in the chassis. For installing the fan
filter, see Installing the Dust Filter section on page 3-11.
Note
Use the pull tab provided to easily access the filter.

OL-25178-08
1-9
Chapter 1
Air Plenum
Air Plenum or air baffle assembly (see Figure 3-7) is used change the air flow pattern of the unit. When
the router is installed with the plenum, the air flow pattern is changed from side-side to front-back. The
air flow front-back pattern provides a rack installation bay with a cool front zone and hot rear zone. For
installing the plenum, see Installing the Chassis in the Air Plenum section on page 3-6.
Note
When the air plenum and the fan filter are installed in the chassis, the system operating
temperature is limited to 55 degrees Celsius.
The air plenum is available from GAW (www.GawTechnology.net). To order an air plenum, contact the
Sales and Marketing support staff at GAW (see Table A-2).
RSP Modules
The Cisco ASR 903 Router is designed to use up to two RSP modules to handle the data plane, network
timing, and control plane functionalities for the router. The RSP configuration allows you to use Cisco
IOS software to control chassis management, redundancy, external management, and system status
indications on the router.
The following sections describe the Cisco ASR 903 Router RSP:
Supported RSPs, page 1-11
A900-RSP1 Supported Interface Modules, page 1-13
A900-RSP2 Supported Interface Modules, page 1-14
A900-RSP3C-400-S Supported Interface Modules, page 1-15
A900-RSP3C-200-S Supported Interface Modules, page 1-15
Supported RSP Features, page 1-16
RSP Redundancy, page 1-16
Network Timing Interfaces, page 1-16
RSP Interfaces, page 1-17
RSP features include:
Loading software onto processor-based interface modules
Redundant RSP managementThe RSP manages detection of RSPs, exchange of health and status
information, role negotiation, function for detection, health and status exchange, role negotiation
Packet processing
Traffic management, including buffering, queuing, and scheduling, Ethernet MAC functions
Network clocking functions including phase and time-of-day for BITS, 1 PPS, 10 MHz, and 1588
PTP clock references.
Storage of software images, system configuration, OBFL, SysLog
PTP packet processing including IEEE 1588-2008 for recovering network timing (frequency, phase,
and time) from upstream PTP clocks, for generating PTP frequency and phase references as inputs
to the SETS, and for distributing them to downstream PTP clocks
1-10
OL-25178-08
Chapter 1

External management interfaces (RS232 console, management ENET, USB console, USB storage)
and system status LED indicators
Supported RSPs
The Cisco ASR 903 Router supports the following RSPs:
Note
Caution
A900-RSP1A-55Provides 2 GB of SDRAM, 5 Mb of TCAM memory, 36Mb buffer table,

576-Mb forwarding memory, and 1,536-Mb packet buffer memory.
A900-RSP1B-55Provides 4 GB of SDRAM, 20 Mb of TCAM memory, 144-Mb buffer table,

1152-Mb forwarding memory, and 1,536-Mb packet buffer memory.
A900-RSP2A-128Provides 4 GB double data rate type three (DDR3) memory, 128 Gbps
aggregate throughput.
A900-RSP2A-64Provides 4 GB double data rate type three (DDR3) memory, 64 Gbps aggregate
throughput.
A900-RSP3C-400-SProvides 8 GB of SDRAM and non-volatile memory, 64MB flash memory,

40 Mb of TCAM memory, 400Gbps throughput.
A900-RSP3C-200-SProvides 8 GB of SDRAM and non-volatile memory, 64MB flash memory,

20 Mb of TCAM memory, 200Gbps throughput.
The supported RSPs have different memory capacities, but they have the same interfaces and
functionality.
The SD memory card is not field replaceable. Do not try to remove or replace it.
A900-RSP1 Module
365626
Figure 1-8

OL-25178-08
1-11
Chapter 1
Figure 1-9
A900-RSP2A-128 Module
391547
Note
SD memory card
SD memory card slot
Installing a mix of RSP modules in the chassis is not supported.

The RSPs do not provide external network interfaces for user traffic. All network interfaces are provided
via separate IMs.
A900-RSP3C-400-S RSP Module
364601
Figure 1-10
1-12
OL-25178-08
Chapter 1

A900-RSP3C-200-S RSP Module
365457
Figure 1-11
A900-RSP1 Supported Interface Modules

Table 1-5
A900-RSP1 Supported Interface Modules and Part Numbers
RSP Module
Interface Modules
Part Number
Slot
A900-RSP1A-55
8-port Gigabit Ethernet SFP Interface Module

(8X1GE)
A900-IMA8S
All
8-port Gigabit Ethernet RJ45 (Copper) Interface

Module (8X1GE)
A900-IMA8T
1-port 10 Gigabit Ethernet XFP Interface Module

(1X10GE)
A900-IMA1X
0-3
16 x T1/E1 Interface Module
A900-IMA16D
All
A900-RSP1B-55
4-Port OC3/STM-1 (OC-3) or 1-Port OC12/STM-4 A900-IMA4OS

(OC-12) Interface Module
14-port Serial Interface Module
A900-IMASER14A/S

OL-25178-08
1-13
Chapter 1
A900-RSP2 Supported Interface Modules

Note
The combination IMs (A900-IMA8S1Z, A900-IMA8T1Z), and the A900-IMA2Z are not supported
on the A900-RSP1A-55 and A900-RSP1B-55 modules on the Cisco ASR 903 Router.
The combination IMs (A900-IMA8S1Z, A900-IMA8T1Z) are not supported on the A900-RSP2-64
RSP module on the Cisco ASR 903 Router.
Table 1-6
A900-RSP2 Supported Interface Modules and Part Numbers
RSP Module
Supported Interface Modules
Part Numbers
Slot
A900-RSP2A-128
8-port Gigabit Ethernet SFP Interface Module (8X1GE)
A900-IMA8S
All
8-port Gigabit Ethernet RJ45 (Copper) Interface Module

(8X1GE)
A900-IMA8T

(1X10GE)
A900-IMA1X
A900-IMA16D
A900-IMA32D
8 X T1/E1 Interface Module
A900-IMA8D
4-Port OC3/STM-1 (OC-3) or 1-Port OC12/STM-4

A900-IMA4OS
SFP Combo IM8-port Gigabit Ethernet (8X1GE) +
A900-IMA8S1Z
1-port 10 Gigabit Ethernet (1X10GE)

Copper Combo IM8-port Gigabit Ethernet (8X1GE)
A900-IMA8T1Z
+ 1-port 10 Gigabit Ethernet Interface Module (1X10GE)
A900-RSP2A-64
2-port 10 Gigabit Ethernet Interface Module (2X10GE)
A900-IMA2Z
6-port 4-wire E & M Interface Module
A900-IMA6EM

(1X10GE)
A900-IMA1X
A900-IMA2Z
A900-IMA4OS
0-2

A900-IMA8S
8-port Gigabit Ethernet RJ45 (Copper) Interface Module
A900-IMA8T
3-5
(8X1GE)
A900-IMA16D
A900-IMA32D
3-5
A900-IMA8D
3-5
6-port E & M Interface Module
A900-IMA6EM
3-5
1-14
OL-25178-08
Chapter 1

A900-RSP3C-400-S Supported Interface Modules

Table 1-7
A900-RSP3C-400 Supported Interface Modules and Part Numbers
RSP Module
Part Numbers
Slot
A900-RSP3C-400-S

(8X1GE)
A900-IMA8S
All1

Module (8X1GE)
A900-IMA8T

(1X10GE)
A900-IMA1X

A900-IMA4OS
SFP Combo IM8-port Gigabit Ethernet (8X1GE) + A900-IMA8S1Z

Copper Combo IM8-port Gigabit Ethernet (8X1GE) A900-IMA8T1Z
+ 1-port 10 Gigabit Ethernet Interface Module
(1X10GE)
2-port 10 Gigabit Ethernet Interface Module
(2X10GE)
A900-IMA2Z

(8X10GE)
A900-IMA8Z

(1X100GE)
A900-IMA1C
4 and 5
2-port 40 Gigabit Ethernet QSFP Interface Module

(2X40GE)
A900-IMA2F
4 and 5
1. There are restrictions using the interface modules in different slots with RSP3 module. Contact Cisco Sales/Support for the
valid combinations..
A900-RSP3C-200-S Supported Interface Modules

Table 1-8
RSP Module
Part Numbers
Slot
A900-RSP3C-200-S

(8X1GE)
A900-IMA8S
All1

Module (8X1GE)
A900-IMA8T

(1X10GE)
A900-IMA1X

A900-IMA4OS
0, 2 and
4

OL-25178-08
1-15
Chapter 1
Table 1-8
RSP Module
Part Numbers
SFP Combo IM8-port Gigabit Ethernet (8X1GE) + A900-IMA8S1Z
Slot
0-4

Copper Combo IM8-port Gigabit Ethernet (8X1GE) A900-IMA8T1Z
+ 1-port 10 Gigabit Ethernet Interface Module
(1X10GE)
(2X10GE)
A900-IMA2Z

(8X10GE)
A900-IMA8Z
2-port 40 Gigabit Ethernet QSFP Interface Module

(2X40GE)
A900-IMA2F
1. There are restrictions using the interface modules in different slots with RSP3 module. Contact Cisco Sales/Support for the
valid combinations..
Supported RSP Features

The RSP provides the following features on the Cisco router:
Centralized data plane, timing, and control plane functions for the system
High-level control of interface modules
Management functionalities for the router
Control plane (host) CPU and associated memory in which IOS-XE and platform control software
runs
Nonvolatile memory for storage of software images, configurations, and system files
Enabling and monitoring the health and presence of fan trays, interface modules, and power supplies
Field replacement and hot-swap capabilities
RSP Redundancy
The Cisco ASR 903 Router chassis includes two RSP slots to allow for redundant RSPs. When the router
uses redundant RSPs, one RSP operates in the active mode and the other operates in the hot standby
mode. Removal or failure of the active RSP results in an automatic switchover to the standby RSP.
Note
If you are using redundant RSPs, both the RSPs must be of the same type because a mixed configuration
of two different RSP types is not supported.
Network Timing Interfaces

The RSP supports the following network timing interfaces:
BITS input/output portRJ48 jack
1 PPS input and outputMini coax connectors
1-16
OL-25178-08
Chapter 1

2.048 or 10 MHz input and outputMini coax connectors
Time of Day (ToD) or 1 PPS input or output portShielded RJ45 jack
Network timing interfaces support redundancy in a redundant RSP configuration. Network timing
interfaces on a redundant RSP remain in operation while the RSP is in hot standby mode.
RSP Interfaces
Figure 1-12
Cisco RSP1 Interfaces Summary

1
10
SYNC
ACT
CONSOLE
1PPS
OUT
1OMHZ
IN
PWR
1OMHZ
OUT
TOD
BITS
MGMT
ENET
STAT
281931
MEM
1PPS
IN
Interface
USB memory port
USB console port
Console port
1 PPS input timing port
1 PPS output timing port
10 MHz input timing port
10 MHz output timing port
Time of Day (ToD) timing port
BITS timing port
10
Ethernet management port
Figure 1-13
Cisco A900-RSP2A Interface Summary
364956
Label
1 2
Label
Interface
USB memory port
USB console port
Console port
10

OL-25178-08
1-17
Chapter 1
Label
Interface
BITS timing port
10
The Cisco A900-RSP2A module has the following front panel interfaces. For information on cable
pinout, see Pinouts, page 4-1.
1 USB Type-A Connector for USB-flash (Label = MEM)
1 USB Type-A Connector for alternate console port (Label = CONSOLE)
RJ45 Connecter for Con/Aux (Label = CONSOLE)
RJ48 Jack for BITS interface. (Label = BITS)
RJ48 Jack for Time-of-Day interface. (Label= TOD)
RJ45 Connecter for Con/Aux (Label = MGMT ENET)
4 Mini-Coax connectors (Label = 1PPS IN, 1PPS OUT, 10MHZ IN, 10MHZ OUT)
Figure 1-14
Cisco A900-RSP3C-400-S Interfaces

2
10
11
364957
Label
Interface
GNSS module slot (optional)
USB memory port
USB console port
Console port
1-18
OL-25178-08
Chapter 1

Label
Interface
10
BITS timing port
11
Figure 1-15
Cisco A900-RSP3C-200-S Interfaces

2
10
11
365458
Label
Interface
GNSS module slot (optional)
USB memory port
USB console port
Console port
10
BITS timing port
11
For more information about installing the RSP, see RSP Installation section on page 3-15. For more
information about the RSP LEDs, see RSP LEDs section on page 4-13.
GNSS Module (A900-CM-GNSS)

The GNSS module is present on the RSP3 modules. It is a pluggable module that allows direct interface
with the external antenna.
Note
Warning
Note
Using a single GPS antenna input for both RSPs requires usage of external splitters.
To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Statement 1023
The GNSS module is not hot swappable.

OL-25178-08
1-19
Chapter 1
GNSS Module RF Input Requirements
The GNSS module requires an active GPS/GNSS antenna with built-in Low-Noise Amplifier (LNA)
for optimal performance. The antenna LNA amplifies the received satellite signals for two purposes:
Compensation of losses on the cable
Lifting the signal amplitude in the suitable range for the receiver frontend
The Amplification required is 22dB gain + cable/connector loss + Splitter signal loss.
The recommended range of LNA gain (LNA gain minus all cable and connector losses) at the
connector of the receiver module is 22dB to 30dB with a minimum of 20dB and a maximum of
35dB.
GNSS module provides 5V to the active antenna through the same RF input.
Surge requirement:
GNSS modules have built-in ESD protections on all pins, including the RF-input pin. However,
additional surge protection may be required if rooftop antennas are being connected, to meet the
regulations and standards for lightning protection in the countries where the end-product is installed.
A lightning protection must be mounted at the place where the antenna cable enters the building.
The primary lightning protection must be capable of conducting all potentially dangerous electrical
energy to PE (Protective Earth).
Surge arrestors should support DC-pass and suitable for the GPS frequency range (1.575GHz) with
low attenuation.
Antenna Sky visibility:

GPS signals can only be received on a direct line of sight between antenna and satellite. The antenna
should see as much as possible from the total sky. For proper timing, minimum of four satellites
should be locked.
Note
The antenna terminal should be earthed at the building entrance in accordance with the ANSI/NFPA 70,
the National Electrical Code (NEC), in particular Section 820.93, Grounding of Outer Conductive Shield
of a Coaxial Cable.
For information on pinout, see GPS Port Pinout.
Interface Modules
The Cisco ASR 903 Router interface modules are a field-replaceable units. In addition to the ports
provided on an RSP, the Cisco ASR 903 Router supports the following interface modules:
Gigabit Ethernet SFP Interface Module, page 1-21
Gigabit Ethernet RJ45 Interface Module, page 1-22
10 Gigabit Ethernet XFP Interface Module, page 1-22
8-port 10 Gigabit Ethernet Interface Module (8X10GE), page 1-23
1-port 100 Gigabit Ethernet Interface Module (1X100GE), page 1-24
2-port 40 Gigabit Ethernet QSFP Interface Module (2X40GE), page 1-24
16 Port T1/E1 Interface Module, page 1-25
1-20
OL-25178-08
Chapter 1

Note
OC-3 Interface Module, page 1-27
Serial Interface Module, page 1-28
E & M Interface Module, page 1-29
8x1 Gigabit Ethernet SFP+ 1x10 Gigabit Ethernet SFP+ Combination Interface Module, page 1-30
8x1 Gigabit Ethernet RJ45 + 1x10 Gigabit Ethernet SFP+ Combination Interface Module, page 1-30
2x1 10 Gigabit Ethernet SFP+ Interface Module, page 1-31
For information about supported interface modules, see the Release Notes for the Cisco ASR 903 Series
Aggregation Services Router.
Gigabit Ethernet SFP Interface Module

The Gigabit Ethernet Small Form-Factor Pluggable (SFP) interface module provides eight Gigabit
Ethernet SFP modules. Figure 1-16 shows the 8 x 1 GE Gigabit Ethernet SFP interface module.
8 x 1 GE Gigabit Ethernet SFP Interface Module
282440
Figure 1-16
For information on supported SFP modules, see Cisco ASR 900 Series Aggregation Services Routers
Data Sheet.
For more information about installing an SFP Gigabit Ethernet module, see the Interface Module
Installation section on page 3-18.

OL-25178-08
1-21
Chapter 1
Gigabit Ethernet RJ45 Interface Module

The Gigabit Ethernet RJ45 interface module provides eight Gigabit Ethernet copper ports. Figure 1-17
shows the interface module.
8 x 1 GE Gigabit Ethernet RJ45 (Copper) Interface Module
282439
Figure 1-17
Data Sheet.
For more information about installing an RJ45 Gigabit Ethernet module, see the Interface Module
10 Gigabit Ethernet XFP Interface Module

The 10 Gigabit Ethernet XFP interface module provides a single port supporting a 10 Gigabit Ethernet
XFP module. Figure 1-18 shows the interface module.
1 x 10 GE Gigabit Ethernet XFP Interface Module
282437
Figure 1-18
1-22
OL-25178-08
Chapter 1

Note
10 Gigabit Ethernet interface modules are not supported in slots 4 and 5.

Data Sheet.
For more information about installing a 10XGE XFP module, see the Interface Module Installation
section on page 3-18.

8x10 Gigabit Ethernet Interface Module
364602
Figure 1-19
The high density 8x10 Gigabit Ethernet interface module supports eight 10 Gigabit Ethernet ports using
SFP+ transceivers cages on the faceplate.
Note
Note
It does not support XFP transceivers on the ports.
The 8X10 GE interface module is supported in slot 0 on the router with the A900-RSP3C-200-S RSP
module. Only 6 ports of the 8 are enabled. The ports enabled are 0, 1, 4, 5, 6, and 7.
Use the hw-module subslot command to enable the interface module in slot 0 of the router. Save the
configuration and reload the router to activate the interface module.
To remove the configuration, use no hw-module subslot command.
Data Sheet.
For more information about installing a 8X10GE module, see the Interface Module Installation section
on page 3-18.

OL-25178-08
1-23
Chapter 1

364604
Figure 1-20
The single port 100 Gigabit Ethernet interface module supports one CPAK optics port.
For information on supported CPAK modules, see Cisco ASR 900 Series Aggregation Services Routers
Data Sheet.
For more information about installing a 1X100GE module, see the Interface Module Installation
2-port 40 Gigabit Ethernet QSFP Interface Module (2X40GE)

364603
Figure 1-21
1-24
OL-25178-08
Chapter 1

The dual port 40 Gigabit Ethernet interface module supports the 40 Gigabit Ethernet port. The 40G
interface is supported using QSFP+ optics. Figure 1-21 shows the interface module.
Data Sheet.
For more information about installing a 2X40GE module, see the Interface Module Installation section
on page 3-18.
16 Port T1/E1 Interface Module

The 16 x T1/E1 interface module provides connectivity for up to 16 x T1/E1 ports through a 100-pin
Amplimite connector. The 16T1/E1 interface module requires the use of a patch panel to provide RJ48
(T1) or BNC (E1) connectors. Figure 1-22 shows the interface module.
282441
Figure 1-22
Data Sheet.
For more information about installing a T1/E1 interface module, see the Interface Module Installation

The 32 xT1/E1 interface module provides connectivity for up to 32 x T1/E1 ports through two 68-pin
Tyco connectors. It is supported on the A900-RSP2A-64 module in slots 3, 4 and 5, and on the
A900-RSP2A-128 on all slots.
The 32 x T1/E1 interface module requires the use of a patch panel to provide RJ48 or BNC connectors.

OL-25178-08
1-25
Chapter 1
391944
Figure 1-23
Data Sheet.
For more information about installing a 32 x T1/E1 interface module, see the Interface Module

The 8T1/E1 interface module provides connectivity for up to 8 x T1/E1 ports through RJ48C port
connectors on the front panel. Figure 1-24 shows the interface module. It is supported on the
A900-RSP2A-64 module in slots 3, 4 and 5, and on the A900-RSP2A-128 on all slots.
364202
Figure 1-24
Data Sheet.
1-26
OL-25178-08
Chapter 1

For more information about installing a 8 x T1/E1 interface module, see the Interface Module
OC-3 Interface Module

The OC-3 interface module can operate as up to four STM-1 interfaces.
Note
The optical interface module is designed for OC-3 and OC-12 traffic, but OC-12 functionality is not
currently supported.
Figure 1-25 shows the interface module.
4 x OC-3 Interface Module
282438
Figure 1-25
Data Sheet.
For more information about installing an optical interface module, see the Interface Module

OL-25178-08
1-27
Chapter 1
Serial Interface Module

The Cisco (A900-IMASER14A/S) is a 14 port serial interface module for the Cisco ASR 903 router. The
Cisco ASR 903 Router module has the following interfaces:
12-in-1 Connector (6)Supports Asynchronous RS-232 interfaces using EIA/TIA-232 DB-25

connectors
68-Pin Connector (2)Supports up to 8 RS-232 and RS-485 interfaces in full or half duplex mode
using 4 RS-232 connectors (DB-25, DB-9, or RJ-45).
Serial Interface Module
303338
Figure 1-26
J0-J
3
J4-J
7
J0-J
J9
J10
J11
J12
Figure 1-27
J13
A900
-IMA
SER
14A/S
PWR
STAT
Cisco ASR 903 Router Front Panel
PWR
J0-J3
J4-J7
J8
J9
J10
J11
J12
J13
Captive screws (2)
68-Pin Connector (2)
12-in-1 Connector (6)
Status (STAT) LED
Power (PWR) LED
LEDsThe LEDs are as follows:
J0J3 and J4J7Indicate the

function of the 68-pin connectors
J8J13Indicate the status of the

12-in-1 connectors
1-28
OL-25178-08
303599
A900-IMASER14A/S
STAT
Chapter 1

For more information about using the LEDs to troubleshoot the Cisco ASR 903 Router, see LED
Summary, page 4-13.
Supported Standards
The Cisco ASR 903 Router supports the following standards
Table 9
General Standards
Standard
Definition
IEEE 1613 2009
IEEE Standard for Environmental and Testing Requirements for

Communications Networking Devices in Electric Power Substations
IEC 61850-3
IEC standard specifying general requirements for substation

automation systems (SAS) communications and related system
requirements.
IEC 60870-2-1:1995
IEC standard for substation environmental conditions
IEC 60870-2-2:1996
IEC standard for substation environmental conditions
IEC 61000-6-5:2001
IEC standard defining immunity for power station and substation

environments
The serial interface module supports several cable types. For more information, see Connecting Serial
Cables, page 3-52 and Serial Cable Pinouts, page 4-9.
E & M Interface Module

The Cisco (A900-IMA6EM) is a 6-port Ear and Mouth (E&M) interface module for the
Cisco ASR 903 router. The interface module provides the router with connectivity to tele-protection
equipments. The front panel of the module consists of:
six port RJ45 connectors
two LED that display Power and Status
one LED per RJ45 port
E & M Interface Module
365000
Figure 1-28
For information on LEDs, see LED Summary.

OL-25178-08
1-29
Chapter 1
For more information about installing the module, see the Interface Module Installation section on
page 3-18.
8x1 Gigabit Ethernet SFP+ 1x10 Gigabit Ethernet SFP+ Combination Interface Module
The 8-port 1 Gigabit Ethernet SFP interface module with the 1-port 10 Gigabit Ethernet interface module
is a high density combination interface module. This module supports 8 Gigabit Ethernet SFP ports and
1 10 Gigabit Ethernet SFP+ port.
8x1 GE SFP + 1x10 GE SFP+ Interface Module
391550
Figure 1-29
Data Sheet.
For more information about installing the 8X1 GE SFP + 1X10 SFP Gigabit Ethernet module, see the
Interface Module Installation section on page 3-18.
8x1 Gigabit Ethernet RJ45 + 1x10 Gigabit Ethernet SFP+ Combination Interface Module
This 8-port 1 Gigabit Ethernet RJ45 (Copper) interface module with the 1-port 10 Gigabit Ethernet
interface module is a high density combination interface module. This module supports 8 Gigabit
Ethernet Copper ports and 1 10 Gigabit Ethernet SFP+ port.
1-30
OL-25178-08
Chapter 1

8x1 GE RJ45 + 1x10 GE SFP+ Interface Module
391551
Figure 1-30
Data Sheet.
For more information about installing the 8X1 GE RJ45 + 1X10 SFP Gigabit Ethernet module, see the
Interface Module Installation section on page 3-18.
2x1 10 Gigabit Ethernet SFP+ Interface Module

The 2 port 10 Gigabit Ethernet interface module provides a dual port supporting a 10 Gigabit Ethernet
SFP+ and XFP module.
2X10 Gigabit Ethernet Interface Module
391549
Figure 1-31
Data Sheet.
For more information about installing the 2X10 GE SFP Gigabit Ethernet module, see the Interface
Module Installation section on page 3-18.

OL-25178-08
1-31
Chapter 1
Blank Deflector (A900-IMA-BLNK-DEF)

The A900-IMA-BLNK-DEF is a special type of blank filler plate that can be used in empty interface
module slots. In addition to just acting as a filler for the empty slots in the router, this blank deflects
additional air towards the interface modules in the slot below it, thereby enhancing the cooling for the
interface module.
Caution
The A900-IMA-BLNK-DEF is module should not be used in slot 0 in the Cisco ASR 903 Router.
For slot 0, always use the filler blank (A900-IMA-BLANK) when a blank filler needs to be used.
For more information on operating temperature, see Example: Configuration with A900-RSP3-200-S
with Blank Deflector (A900-IMA-BLNK-DEF), page 1-33.
Maximum Operating Ambient Temperature Support for RSP3 Modules

The router supports multiple fan trays with different cooling capacities. The maximum operating
temperature of the router using the RSP3 modules, depends on the fan tray and the interface modules
used in the router.
The tables below provide and overview of the operating ambient temperature limits for different fan tray
and interface module combinations. These values are specified for side-to-side airflow configuration.
Note
The temperature range could further be restricted by the optical modules are used in the router.
Table 1-10
Operating Temperature for A900-RSP3C-400-S Module
Interface Modules
Fan Tray
Operating Temperature Limit

(C)
A900-IMA1X
A903-FAN
40 to 55
A900-IMA8T
A903-FAN-E
40 to 50
A900-IMA8Z
A903-FAN
40 to 55
A900-IMA2F
A903-FAN-E
40 to 50
A900-IMA1C
A903-FAN
40 to 45
A903-FAN-E
40 to 40
A900-IMA8S
A900-IMA2Z
A900-IMA8T1Z
A900-IMA8S1Z
1-32
OL-25178-08
Chapter 1

Table 1-11
Operating Temperature for A900-RSP3C-200-S Module
Interface Modules
Fan Tray
Operating Temperature Limit

(C)
A900-IMA1X
A903-FAN
40 to 651
A900-IMA8T
A903-FAN-E
40 to 651
A900-IMA8Z
A903-FAN
40 to 651
A900-IMA2F
A903-FAN-E
40 to 552
A900-IMA8S
A900-IMA2Z
A900-IMA8T1Z
A900-IMA8S1Z
1. Maximum operating temperature of 65 C is supported only with EXT/RGD/IND optical modules.

2. A900-IMA8Z supports a maximum temperature of 65 C with A903-FAN or A903-FAN-E if A900-IMA-BLNK-DEF is used
in the slot above the interface module.
Example: Configuration with A900-RSP3-200-S with Blank Deflector (A900-IMA-BLNK-DEF)

In the below configuration, the overall operating temperature of the router is enhanced by using
A900-IMA-BLNK-DEF in the slots above A900-IMA8Z interface module. The maximum operating
temperature of the router is enhanced from 55 C to 65C by using A900-IMA-BLNK-DEF in slots 1 and
5 (above A900-IMA8Z).
Note
To support 65C ambient temperature, EXT optics need to be used for 10G ports.
A900-IMA-BLNK-DEF
A900-RSP3C-200
A900-IMA-8T1Z
A900-RSP3C-200
A900-IMA-8T1Z
A900-IMA-BLNK-DEF
PSU
PSU
A900-IMA8Z
A903-FAN-E
A900-IMA8Z
Temperature Sensor
The Cisco ASR 903 Router has a temperature sensor to detect overtemperature conditions inside the
chassis
Temperature Sensors on the A900 RSP1 and A900 RSP2 modules

The overtemperature detection trips at 75 degrees C +/- 5% with the ambient (inlet) trip point at 67
degrees C. This condition is reported to the processor as an interrupt, and the software takes action to
generate the appropriate alarms.

OL-25178-08
1-33
Chapter 1
Interface Numbering
Temperature Sensors on the A900 RSP3 modules

The maximum operating temperature of RSP3 module and the interface modules is less than the
maximum operating temperature of the Cisco ASR 903 router. The IOS software decides the appropriate
temperature thresholds to generate warnings, and shuts down the system when abnormally high
temperature is detected. For more information, see Maximum Operating Ambient Temperature Support
for RSP3 Modules, page 1-32.
Serial Number Label Location

Figure 1-32 shows the serial number label location on the Cisco ASR 903 Router.
Figure 1-32
Cisco ASR 903 Router Serial Number Location
11 letters and numbers
282407
Serial Number
Interface Numbering
The Cisco ASR 903 Router chassis includes:
Six interface module slots
Two RSP module slots
Two power supply slots
One fan tray slot
Each network interface on a Cisco ASR 903 Router is identified by a slot number and a port number.
1-34
OL-25178-08
Chapter 1

Interface Numbering
Figure 1-33 shows interface numbering in a Cisco ASR 903 Router.

Figure 1-33
Cisco ASR 903 Router Slot Numbers
GE-0
GE-1
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
11
PWR
RUDY RSP
FAN TEMP
SYNC
STAT
ACT
GE-0
GE-1
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
GE-0
GE-1
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
10
PWR
MEM
CONSOLE
1PPS
IN
MEM
CONSOLE
1PPS
IN
PWR
1PPS
OUT
1OMHZ
IN
1OMHZ
OUT
TOD
BITS
MGMT
ENET
1PPS
OUT
1OMHZ
IN
1OMHZ
OUT
TOD
BITS
MGMT
ENET
STAT
24V60V
28A
CRIT MAJ MIN
STAT
STAT
PWR
PWR
RUDY RSP
STAT
SYNC
ACT
7 S
7 S
7 S
PWR
PWR
STAT
PWR
STAT
INPUT
OK
OUTPUT
FAIL
24V60V
INPUT
OK
OUTPUT
FAIL
28A
ALARM
RSP slot 1
RSP slot 0
Fan tray slot
Power supply slot 1
Power supply slot 0
Interface module slot 0
10
11
209290
STAT
Following is an explanation of the slot or port numbering:
Note
The numbering format is Interface type slot or interface number. Interface (port) numbers begin at
logical 0 for each interface type.
Interface module slots are numbered from bottom to top, with logical interfaces on each module
numbered from left to right. Interfaces are hard-wired. Therefore, port 0 is always logical interface
0/0, port 1 is always logical interface 0/1, and so on.
The input parameter for the following commands changes based on the active RSP slot number. The
active RSP in slot 0 is refereed to as "0/ slot_num", else if the active RSP is slot 1, it is refereed as
1/"slot_num". The output for the command is displayed accordingly:
show diag all eeprom detail
show platform software trace message iomd
show platform software agent iomd

OL-25178-08
1-35
Chapter 1
show platform software peer shell-manager brief
show platform software peer chassis-manager
show platform software memory iomd
set platform software trace iomd
For regulatory compliance and safety information, see the Regulatory Compliance and Safety
Information for the Cisco ASR 903 Router document.
1-36
OL-25178-08
CH A P T E R

The following sections describe how to prepare for the installation of the Cisco ASR 903 Router at your
site:
Safety Guidelines, page 2-1
Site Planning, page 2-10
Receiving the Cisco ASR 903 Router, page 2-21
Safety Guidelines
Before you begin the installation of the Cisco ASR 903 Router, review the safety guidelines in this
chapter to avoid injuring yourself or damaging the equipment.
In addition, before replacing, configuring, or maintaining the Cisco ASR 903 Router, review the safety
warnings listed in Regulatory Compliance and Safety Information for the Cisco ASR 903 Router.
The following sections describe the safety guidelines for the Cisco ASR 903 Router:
Standard Warning Statements, page 2-2
Safety Guidelines for Personal Safety and Equipment Protection, page 2-4
Safety Precautions for Module Installation and Removal, page 2-4
Safety with Electricity, page 2-5
Power Supply Considerations, page 2-10
Preventing ESD Damage, page 2-10

OL-25178-08
2-1
Chapter 2
Safety Guidelines
Standard Warning Statements

To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance
and Safety Information document that accompanied this device.
Warning
The appliance must be connected to a grounded outlet. Statement 0414
Warning
To avoid or reduce the risk of personal injury, do not use the product if the product has been exposed
to irregular environmental conditions, if the product has been misused or if parts of the product have
been damaged. Consult qualified service personnel. Never try to service the product yourself.
Statement 0416
Warning
To reduce the risk of c shock, fire or personal injury, do not place power cables in areas where they
may be walked on or damaged by items placed upon or against it. Statement 0417
Warning
This product is intended for use in a normal environment based on the standard IEC 60950-1. Do not
use the product in vehicles, on board ships, in aircrafts or in medical applications with physical
connection to the patient, nor in environments with exposure to moisture, dust, vibration or ingress of
water. Statement 0418
Warning
Do not work on the system or connect or disconnect cables during periods of lightning activity.
Statement 1001
Warning
Read the installation instructions before connecting the system to the power source. Statement 1004
Warning
To prevent bodily injury when mounting or servicing this unit in a rack, you must take special
precautions to ensure that the system remains stable. The following guidelines are provided to ensure
your safety: This unit should be mounted at the bottom of the rack if it is the only unit in the rack. When mounting
this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom
of the rack. If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit
in the rack. Statement 1006
Warning
This unit is intended for installation in restricted access areas. A restricted access area can be
accessed only through the use of a special tool, lock and key, or other means of security.
Statement 1017
Warning
To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Statement 1023
2-2
OL-25178-08
Chapter 2

Safety Guidelines
Warning
If the symbol of suitability with an overlaid cross appears above a port, you must not connect the port
to a public network that follows the European Union standards. Connecting the port to this type of
public network can cause severe injury or damage your router. Statement 1031
Warning
Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry
tub, in a wet basement, or near a swimming pool. Statement 1035
Warning
Never install telephone jacks in wet locations unless the jack is specifically designed for wet
locations. Statement 1036
Warning
Never touch uninsulated telephone wires or terminals unless the telephone line has been
disconnected at the network interface. Statement 1037
Warning
Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote
risk of electric shock from lightning. Statement 1038
Warning
To report a gas leak, do not use a telephone in the vicinity of the leak. Statement 1039
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations.
Statement 1040
Warning
Before opening the unit, disconnect the telephone-network cables to avoid contact with
telephone-network voltages. Statement 1041
Warning
To prevent the system from overheating, do not operate it in an area that exceeds the maximum
recommended ambient temperature of 149F (65C). Statement 1047
Warning
The chassis should be mounted on a rack that is permanently affixed to the building. Statement 1049
Warning
IMPORTANT SAFETY INSTRUCTIONS: This warning symbol means danger. You are in a situation that
could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with
electrical circuitry and be familiar with standard practices for preventing accidents. Use the
statement number provided at the end of each warning to locate its translation in the translated safety
warnings that accompanied this device. Statement 1071

OL-25178-08
2-3
Chapter 2
Safety Guidelines
Warning
No user-serviceable parts inside. Do not open. Statement 1073
Warning
This is a Class A Device and is registered for EMC requirements for industrial use. The seller or buyer
should be aware of this. If this type was sold or purchased by mistake, it should be replaced with a
residential-use type. Statement 294
Warning
This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures. Statement 340
Warning
This equipment is in compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
Safety Guidelines for Personal Safety and Equipment Protection

The following guidelines help ensure your safety and protect the equipment. This list does not include
all the potentially hazardous situations. Therefore, you should be on alert.
Before moving the system, always disconnect all the power cords and interface cables.
Never assume that power is disconnected from a circuit; always check.
Before and after installation, keep the chassis area clear and dust-free.
Keep tools and assembly components away from walk areas where you or others could trip over
them.
Do not work alone if potentially hazardous conditions exist.
Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.
Do not wear loose clothing that may get caught in the chassis.
When working under conditions that may be hazardous to your eyes, wear safety glasses.
Safety Precautions for Module Installation and Removal

Be sure to observe the following safety precautions when you work on the router.
To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance
and Safety Information document that accompanied this device.
Warning
For connections outside the building where the equipment is installed, the following ports must be
connected through an approved network termination unit with integral circuit protection. Statement
1044
Warning
Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into
beams or view directly with optical instruments. Statement 1051
2-4
OL-25178-08
Chapter 2

Safety Guidelines
Warning
Class 1M laser radiation when open. Do not view directly with optical instruments. Statement 1053
Warning
Class 1 (CDRH) and Class 1M (IEC) laser products. Statement 1055
Warning
Do not stare into the beam or view it directly with optical instruments. Statement 1011
Warning
Invisible laser radiation present. Statement 1016
Warning
Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF
or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables,
detach the end away from the unit first. Statement 1026
Warning
Blank faceplates and cover panels serve three important functions: they prevent exposure to
hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI)
that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not
operate the system unless all cards, faceplates, front covers, and rear covers are in place.
Statement 1029
Warning
Hazardous voltage or energy is present on the backplane when the system is operating. Use caution
when servicing. Statement 1034
Warning
Safety with Electricity

Warning
Before working on a chassis or working near power supplies, unplug the power cord on AC units;
disconnect the power at the circuit breaker on DC units. Statement 12
Warning
Before working on equipment that is connected to power lines, remove jewelry (including rings,
necklaces, and watches). Metal objects will heat up when connected to power and ground and can
cause serious burns or weld the metal object to the terminals. Statement 43

OL-25178-08
2-5
Chapter 2
Safety Guidelines
Warning
To prevent accidental discharge in the event of a power line cross, route on-premise wiring away
from power cables and off-premise wiring, or use a grounded shield to separate the on-premise
wiring from the power cables and off-premise wiring. A power line cross is an event, such as a
lightning strike, that causes a power surge. Off-premise wiring is designed to withstand power line
crosses. On-premise wiring is protected from power line crosses by a device that provides
overcurrent and overvoltage protection. Nevertheless, if the on-premise wiring is in close proximity
to or not shielded from, the off-premise wiring or power cable during a lightning strike or power
surge, the on-premise wiring can carry a dangerous discharge to the attached interface, equipment,
or nearby personnel. Statement 338
Warning
High leakage current earth connection essential before connection to system power supply.
Statement 342
Warning
Do not work on the system or connect or disconnect cables during periods of lightning activity.
Statement 1001
Warning
Before performing any of the following procedures, ensure that power is removed from the DC circuit.
Statement 1003
Warning
Warning
This product relies on the buildings installation for short-circuit (overcurrent) protection. Ensure that
the protective device is rated for 550 W DC Power Supply (PID A900-PWR550-D and
A900-PWR550-D-E): For a -48/-60 VDC installation, the wire shall be 12 AWG minimum with a 20 A
circuit breaker. For a 24 VDC installation, the wire shall be 8 AWG minimum with a 40 A branch circuit
breaker. Statement 1005
Warning
This product relies on the buildings installation for short-circuit (overcurrent) protection. Ensure that
the protective device is rated for 1200 W DC Power Supply (PID A900-PWR1200-D): For a -48/-60 VDC
installation, the wire shall be 10 AWG minimum with a 50 A circuit breaker. Statement 1005
Warning
This product relies on the buildings installation for short-circuit (overcurrent) protection. For an AC
installation, ensure that the branch circuit breaker is rated a maximum 20A.
Warning
There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with
the same or equivalent type recommended by the manufacturer. Dispose of used batteries according
to the manufacturers instructions. Statement 1015
2-6
OL-25178-08
Chapter 2

Safety Guidelines
Warning
This unit is intended for installation in restricted access areas. A restricted access area can be
accessed only through the use of a special tool, lock and key, or other means of security.
Statement 1017
Warning
Take care when connecting units to the supply circuit so that wiring is not overloaded. Statement 1018
Warning
The plug-socket combination must be accessible at all times, because it serves as the main
disconnecting device. Statement 1019
Warning
To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network
voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some
LAN and WAN ports both use RJ45 connectors. Use caution when connecting cables. Statement 1021
Warning
A readily accessible two-poled disconnect device must be incorporated in the fixed wiring. Statement
1022
Warning
To reduce the risk of fire, use only 26 AWG or larger telecommunication line cord. Statement 1023
Warning
This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection
authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024
Warning
Use copper conductors only. Statement 1025
Warning
Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF
or ON. To avoid c shock, use caution when working near WAN ports. When detaching cables, detach
the end away from the unit first. Statement 1026
Warning
This unit might have more than one power supply connection. All connections must be removed to
de-energize the unit. Statement 1028
Warning
To prevent personal injury or damage to the chassis, never attempt to lift or tilt the chassis using the
handles on modules (such as power supplies, fans, or cards); these types of handles are not designed
to support the weight of the unit. Statement 1032

OL-25178-08
2-7
Chapter 2
Safety Guidelines
Warning
Connect the unit only to DC power source that complies with the safety extra-low voltage (SELV)
requirements in IEC 60950 based safety standards. Statement 1033
Warning
Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry
tub, in a wet basement, or near a swimming pool. Statement 1035
Warning
Never install telephone jacks in wet locations unless the jack is specifically designed for
wet locations. Statement 1036
Warning
Before opening the unit, disconnect the telephone-network cables to avoid contact with
telephone-network voltages. Statement 1041
Warning
This equipment must be installed and maintained by service personnel as defined by AS/NZS 3260.
Incorrectly connecting this equipment to a general-purpose outlet could be hazardous. The
telecommunications lines must be disconnected 1) before unplugging the main power connector or 2)
while the housing is open, or both. Statement 1043
Warning
This product requires short-circuit (overturned) protection, to be provided as part of the building
installation. Install only in accordance with national and local wiring regulations. Statement 1045
Warning
When installing or replacing the unit, the ground connection must always be made first and
disconnected last. Statement 1046
Warning
When you connect or disconnect the power and relay connector with power applied, an electrical arc
can occur. This could cause an explosion in hazardous area installations. Be sure that power is
removed from the switch and alarm circuit. Be sure that power cannot be accidentally turned on or
verify that the area is nonhazardous before proceeding. Failure to securely tighten the power and
relay connector captive screws can result in an electrical arc if the connector is accidentally
removed. Statement 1058
Warning
Failure to securely tighten the power and relay connector captive screws can result in an electrical
arc if the connector is accidentally removed. Statement 397
Warning
This equipment is intended to be grounded. Ensure that the host is connected to earth ground during
normal use.
2-8
OL-25178-08
Chapter 2

Safety Guidelines
Warning
If you connect or disconnect the console cable with power applied to the switch or any device on the
network, an electrical arc can occur. This could cause an explosion in hazardous location
installations. Be sure that power is removed or the area is nonhazardous before proceeding. To verify
switch operation, perform POST on the switch in a nonhazardous location before installation.
Statement 1065
Warning
Installation of the equipment must comply with local and national electrical codes. Statement 1074
Warning
Hazardous voltage or energy may be present on DC power terminals. Always replace cover when
terminals are not in service. Be sure uninsulated conductors are not accessible when cover is in
place. Statement 1075
When working on equipment powered by electricity, follow these guidelines:
Locate the rooms emergency power-off switch. If an electrical accident occurs, you will be able to
quickly turn off the power.
Before working on the system, turn off the DC main circuit breaker and disconnect the power
terminal block cable.
Before doing the following, disconnect all power:

Working on or near power supplies
Installing or removing a router chassis or network processor module
Performing most hardware upgrades
Never install equipment that appears damaged.
Carefully examine your work area for possible hazards, such as moist floors, ungrounded power
extension cables, and missing safety grounds.
Never assume that power is disconnected from a circuit; always check.
Never perform any action that creates a potential hazard to people or makes the equipment unsafe.
If an electrical accident occurs, proceed as follows:

Use caution, and do not become a victim yourself.
Turn off power to the router.
If possible, send another person to get medical aid. Otherwise, determine the condition of the
victim, and then call for help.

Determine whether the person needs rescue breathing or external cardiac compressions; then
take appropriate action.

In addition, use the following guidelines when working with any equipment that is disconnected from a
power source, but still connected to telephone wiring or network cabling:
Never install telephone wiring during a lightning storm.
Never install telephone jacks in wet locations unless the jack is specifically designed for it.
Never touch uninsulated telephone wires or terminals unless the telephone line is disconnected at
the network interface.
When installing or modifying telephone lines, use caution.

OL-25178-08
2-9
Chapter 2
Site Planning
Power Supply Considerations

Check the power at your site to ensure that you are receiving clean power (free of spikes and noise).
Install a power conditioner if necessary.
Warning
This equipment is designed for connection to TN and IT power systems. Statement 16
Preventing ESD Damage

Warning
This equipment needs to be grounded. Use a green and yellow 6 AWG ground wire to connect the host
to earth ground during normal use. Statement 383
Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD can occur
when electronic printed circuit cards are improperly handled and can cause complete or intermittent
failures. When removing and replacing modules, always follow ESD prevention procedures:
Note
Ensure that the router chassis is electrically connected to earth ground.
Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. To channel unwanted
ESD voltages safely to ground, connect the clip to an unpainted surface of the chassis frame. To
guard against ESD damage and shocks, the wrist strap and cord must operate effectively.
If no wrist strap is available, ground yourself by touching a metal part of the chassis.
When installing a component, use any available ejector levers or captive installation screws to
properly seat the bus connectors in the backplane or midplane. These devices prevent accidental
removal, provide proper grounding for the system, and help to ensure that bus connectors are
properly seated.
When removing a component, use available ejector levers or captive installation screws, if any, to
release the bus connectors from the backplane or midplane.
Handle components by their handles or edges only; do not touch the printed circuit boards or
connectors.
Place a removed component board side up on an antistatic surface or in a static-shielding container.

If you plan to return the component to the factory, immediately place it in a static-shielding
container.
Avoid contact between the printed circuit boards and clothing. The wrist strap only protects
components from ESD voltages on the body; ESD voltages on clothing can still cause damage.
Never attempt to remove the printed circuit board from the metal carrier.
For the safety of your equipment, periodically check the resistance value of the antistatic wrist strap. It
should be between 1 and 10 Mohm.
Site Planning
The following sections describe how to plan for the installation of the Cisco ASR 903 Router:
2-10
OL-25178-08
Chapter 2

Site Planning
General Precautions, page 2-11
Site Planning Checklist, page 2-11
Site Selection Guidelines, page 2-12
Air Flow Guidelines, page 2-13
Floor Loading Considerations, page 2-14
Site Power Guidelines, page 2-14
Site Cabling Guidelines, page 2-16
Rack-Mounting Guidelines, page 2-18
Installation Checklist, page 2-20
Creating a Site Log, page 2-21
General Precautions
Observe the following general precautions when using and working with your Cisco ASR 903 Router
system:
Keep your system components away from radiators and heat sources and do not block cooling vents.
Do not spill food or liquids on your system components and never operate the product in a wet
environment.
Do not push any objects into the openings of your system components. Doing so can cause fire or
electric shock by shorting out interior components.
Position system cables and power supply cables carefully. Route system cables and the power supply
cable and plug so that they cannot be stepped on or tripped over. Be sure that nothing else rests on
your system component cables or power cable.
Do not modify power cables or plugs. Consult a licensed electrician or your power company for site
modifications. Always follow your local and national wiring rules.
If you turn off your system, wait at least 30 seconds before turning it on again to avoid system
component damage.
Site Planning Checklist

Use the following checklist to perform and account for all the site planning tasks described in this
chapter:
The site meets the environmental requirements.
The sites air conditioning system can compensate for the heat dissipation of the
The floor space that the Cisco ASR 903 Router occupies can support the weight of the system.
Electrical service to the site complies with the requirements.
The electrical circuit servicing the Cisco ASR 903 Router complies with the requirements.
Consideration has been given to the console port wiring and limitations of the cabling involved,
according to TIA/EIA-232F.
The Cisco ASR 903 Router Ethernet cabling distances are within limitations.

OL-25178-08
2-11
Chapter 2
Site Planning
The equipment rack in which you plan to install the Cisco ASR 903 Router complies with
requirements.
In selecting the location of the rack, careful consideration has been given to safety, ease of
maintenance, and proper airflow.
Site Selection Guidelines

The Cisco ASR 903 Router requires specific environmental operating conditions. Temperature,
humidity, altitude, and vibration can affect the performance and reliability of the router. The following
sections provide specific information to help you plan for the proper operating environment.
The Cisco ASR 903 Router is designed to meet the industry EMC, safety, and environmental standards
described in the Regulatory, Safety, and Compliance Information for the Cisco ASR 903 Router.
Environmental Requirements
The Cisco ASR 903 Router is Telcordia GR-3108-CORE Class-1 or GR-63-Core Indoor compliant.
Environmental monitoring in the Cisco ASR 903 Router protects the system and components from
damage caused by excessive voltage and temperature conditions. To ensure normal operation and avoid
unnecessary maintenance, plan and prepare your site configuration before installation. After installation,
make sure that the site maintains the environmental characteristics described in Cisco ASR 900 Series
Aggregation Services Routers Data Sheet.
For an outside plant installation (cell site cabinet, hut etc.), it is required that the Cisco ASR 903 Router
be protected against airborne contaminants, dust, moisture, insects, pests, corrosive gases, polluted air
or other reactive elements present in the outside air. To achieve this level of protection, we recommend
that the unit be installed in a fully sealed enclosure or cabinet. Examples of such cabinets include IP65
cabinets with heat exchanger complying with Telecordia GR487. Temperature must be maintained
within 40C to 65C (depending upon which generation of RSP is used).
Physical Characteristics
Be familiar with the physical characteristics of the Cisco ASR 903 Router to assist you in placing the
system in the proper location. For more information, see the Cisco ASR 900 Series Aggregation Services
Routers Data Sheet.
2-12
OL-25178-08
Chapter 2

Site Planning
Air Flow Guidelines

Cool air is circulated through the Cisco ASR 903 Router by a fan tray located along the right side of the
router. Air flow is side-to-side, right to left, as shown in Cisco ASR 903 Router Chassis Air Flow.
Figure 2-1
Cisco ASR 903 Router Chassis Air Flow
Room air
344738
Air exhaust
The fan trays maintain acceptable operating temperatures for the internal components by drawing in cool
air through the vents, and circulating the air through the chassis.
The following guidelines will help you plan your equipment rack configuration:
To ensure adequate air flow through the equipment rack, we recommend that you maintain a
clearance of at least 80 mm on each side of the rack at all times.
If airflow through the equipment rack and the routers that occupy it is blocked or restricted, or if the
ambient air being drawn into the rack is too warm, an overtemperature condition can occur within
the rack and the routers that occupy it.
The site should also be as dust-free as possible. Dust tends to clog the router fans, reducing the flow
of cooling air through the equipment rack and the routers that occupy it, thus increasing the risk of
an overtemperature condition.
Enclosed racks must have adequate ventilation. Ensure that the rack is not congested, because each
router generates heat. An enclosed rack should have louvered sides and a fan to provide cooling air.
Heat that is generated by the equipment near the bottom of the rack can be drawn upward into the
intake ports of the equipment above.
When mounting a chassis in an open rack, ensure that the rack frame does not block the side intakes
and the exhaust fans.
When rack-installed equipment fails, especially equipment in an enclosed rack, try operating the
equipment by itself, if possible. Power off all other equipment in the rack (and in adjacent racks) to
give the router maximum cooling air and clean power.
Avoid locating the Cisco ASR 903 Router in a location in which the chassis air intake vents may
draw in the exhaust air from adjacent equipment. Consider how the air flows through the router; the
airflow direction is side to side, with ambient air drawn in from the vents located on the front right
of the chassis.

OL-25178-08
2-13
Chapter 2
Site Planning
Ensure that cables do not obstruct the air-inlet and air-exhaust grid of the chassis as it may lead to
improper ventilation, overheating of the equipment, and dust accumulation.
Air Flow Guidelines for Enclosed Rack Installation

To install a Cisco ASR 903 Router in a 4-post enclosed cabinet, the front and rear doors of the cabinet
must be removed or be perforated with a minimum of 65% open area (70% for ETSI 800mm racks).
If you are mounting the chassis in a 4-post enclosed cabinet, ensure that you have a minimum of 6 inches
(15.24 cm) of clearance on each side of the chassis.
Floor Loading Considerations

Ensure that the floor under the rack supporting the Cisco ASR 903 Routers is capable of supporting the
combined weight of the rack and all the other installed equipment.
To assess the weight of a fully configured Cisco ASR 903 Router, refer to Cisco ASR 900 Series
Aggregation Services Routers Data Sheet.
For additional information about floor loading requirements, consult GR-63-CORE, Network Equipment
Building System (NEBS) Requirements: Physical Protection.
Site Power Guidelines

The Cisco ASR 903 Router has specific power and electrical wiring requirements. Adhering to these
requirements ensures reliable operation of the system. Follow these precautions and recommendations
when planning your site power for the Cisco ASR 903 Router:
Caution
The redundant power option provides a second, identical power supply to ensure that power to the
chassis continues uninterrupted if one power supply fails or input power on one line fails.
In systems configured with the redundant power option, connect each of the two power supplies to
separate independent power source. If you fail to do this, your system might be susceptible to total
power failure due to a fault in the external wiring or a tripped circuit breaker.
To prevent a loss of input power, be sure that the total maximum load on each circuit supplying the
power supplies is within the current ratings of the wiring and the breakers.
Check the power at your site before installation and periodically after installation to ensure that you
are receiving clean power. Install a power conditioner if necessary.
Provide proper grounding to avoid personal injury and damage to the equipment due to lightning
striking power lines or due to power surges. The chassis ground must be attached to a central office
or other interior ground system.
This product requires short-circuit (overcurrent) protection, to be provided as part of the building
installation. Install only in accordance with national and local wiring regulations.
2-14
OL-25178-08
Chapter 2

Site Planning
Note
The Cisco ASR 903 Router installation must comply with all the applicable codes and is approved for
use with copper conductors only. The ground bond fastening hardware should be of compatible material
and preclude loosening, deterioration, and electrochemical corrosion of hardware and joined material.
Attachment of the chassis ground to a central office or other interior ground system must be made with
a 6 AWG gauge wire, copper ground conductor at a minimum.
The maximum power draw of the Cisco ASR 903 Router chassis and its configurable hardware
components are listed in the following table. The maximum power draw values are not affected by
whether the router chassis contains 1 or 2 power supplies AC or DC.
Hardware component(s)
Maximum power draw value
Router chassis with 2 power supplies, 1 fan tray, and 1 RSP1A
195 W
Router chassis with 2 power supplies, 1 fan tray, and 1 RSP1B
210 W
A900-RSP1A-55 (standby)
100 W
A900-RSP1B-55 (standby)
100 W
A900-RSP2A-64 (active)
70 W
55 W
A900-RSP2A-128 (active)
100 W
85 W
A900-RSP3-400-S (active)
230 W
A900-RSP3-400-S (standby)
230 W
A900-RSP3-200-S (active)
160 W
A900-RSP3-200-S (standby)
160 W
A900-IMA1X (1-port 10 GE XFP interface module)
13.0 W
A900-IMA8T (8-port 1 GE RJ45 interface module)
17.5 W
A900-IMA8S (8-port 1 GE SFP interface module)
17.5 W
A900-IMA8D (8-port T1/E1 interface module)
14.5 W
14.5 W
18 W
A900-IMA4OS (4-Port OC3 interface Module)
26 W
A900-IMA8S1Z (8-port 1GE SFP + 1-port 10 GE interface module) 29 W

A900-IMA8T1Z (8-port 1GE RJ-45 Copper + 1 10 GE interface
module
27 W
A900-IMA2Z (2-port 10 GE interface module)
24 W
A900-IMA8Z (8-port 10 Gigabit Ethernet Interface Module)
60 W
A900-IMA1C (1-port 100 Gigabit Ethernet Interface Module)
60 W
A900-IMA2F (2-port 40 Gigabit Ethernet QSFP Interface Module)
60 W
A900-IMA6EM (6-port E & M Interface Module)
20 W

OL-25178-08
2-15
Chapter 2
Site Planning
Electrical Circuit Requirements

Each Cisco ASR 903 Router requires a dedicated electrical circuit. If you equip it with dual power feeds,
provide a separate circuit for each power supply to avoid compromising the power redundancy feature.
The Cisco ASR 903 Routers can be powered by a DC source or an AC source. Ensure that equipment
grounding is present and observe the power strip ratings. Make sure that the total ampere rating of all
products plugged into the power strip does not exceed 80% of the rating.
For more information about the Cisco ASR 903 Router power supply, see the Power Supply Features
Site Cabling Guidelines

This section contains guidelines for wiring and cabling at your site. When preparing your site for
network connections to the Cisco ASR 903 Router, consider the type of cable required for each
component, and the cable limitations. Consider the distance limitations for signaling, electromagnetic
interference (EMI), and connector compatibility. Possible cable types are fiber, thick or thin coaxial, foil
twisted-pair, or unshielded twisted-pair cabling.
Also consider any additional interface equipment you need, such as transceivers, hubs, switches,
modems, channel service units (CSU), or data service units (DSU).
Before you begin, read these important notes about cabling:
The T1/E1 interface module for the Cisco ASR 903 Router uses a high-density connector that
requires the use of a T1/E1 interface cable and a customer-provided patch panel. For more
information, see Connecting T1/E1 cables section on page 3-49.
Shielded cables must be used to connect to the RS-48 alarm connector on the fan tray in order to
comply with FCC/EN55022/CISPR22 Class A emissions requirements. For information about the
fan tray alarm port, see Connecting the Fan Tray Alarm Port section on page 3-54.
Before you install the Cisco ASR 903 Router, have all the additional external equipment and cables on
hand. For information about ordering, contact a Cisco customer service representative.
The extent of your network and the distances between the network interface connections depend in part
on the following factors:
Signal type
Signal speed
Transmission medium
The distance and rate limits referenced in the following sections are the IEEE-recommended maximum
speeds and distances for signaling purposes. Use this information as a guideline in planning your
network connections prior to installing the Cisco ASR 903 Router.
If wires exceed the recommended distances, or if wires pass between buildings, give special
consideration to the effect of a lightning strike in your vicinity. The electromagnetic pulse caused by
lightning or other high-energy phenomena can easily couple enough energy into unshielded conductors
to destroy electronic devices. If you have had problems of this sort in the past, you may want to consult
experts in electrical surge suppression and shielding.
2-16
OL-25178-08
Chapter 2

Site Planning
Asynchronous Terminal Connections

The RSP provides a console port to connect a terminal or computer for local console access through RJ45
connector or USB connector. The RJ45 port connector supports RS-232 asynchronous data with distance
recommendations specified in the IEEE RS-232 standard.
Interference Considerations
When wires are run for any significant distance, there is a risk that stray signals will be induced on the
wires as interference. If interference signals are strong, they can cause data errors or damage to the
equipment.
The following sections describe sources of interference and how to minimize its effects on the
Cisco ASR 903 Router system.
Electromagnetic Interference
All equipment powered by AC current can propagate electrical energy that can cause EMI and possibly
affect the operation of other equipment. The typical sources of EMI are equipment power cords and
power service cables from electric utility companies.
Strong EMI can destroy the signal drivers and receivers in the Cisco ASR 903 Router and even create an
electrical hazard by causing power surges through the power lines into installed equipment. These
problems are rare but could be catastrophic.
To resolve these problems, you need specialized knowledge and equipment that could consume
substantial time and money. However, you can ensure that you have a properly grounded and shielded
electrical environment, paying special attention to the need for electrical surge suppression.
For information about the electrode magnetic compliance standards supported on the
Cisco ASR 903 Router, see Regulatory Compliance and Safety Information for the
Radio Frequency Interference

When electromagnetic fields act over a long distance, radio frequency interference (RFI) may be
propagated. Building wiring can often act as an antenna, receiving the RFI signals and creating more
EMI on the wiring.
If you use twisted-pair cable in your plant wiring with a good distribution of grounding conductors, the
plant wiring is unlikely to emit radio interference. If you exceed the recommended distances, use a
high-quality twisted-pair cable with one ground conductor for each data signal.
Lightning and AC Power Fault Interference

If signal wires exceed the recommended cabling distances, or if signal wires pass between buildings, you
should consider the effect that a lightning strike in your vicinity might have on the
The electromagnetic pulse (EMP) generated by lightning or other high-energy phenomena can couple
enough energy into unshielded conductors to damage or destroy electronic equipment. If you have
previously experienced such problems, you should consult with RFI and EMI experts to ensure that you
have adequate electrical surge suppression and shielding of signal cables in your Cisco ASR 903 Router
operating environment.

OL-25178-08
2-17
Chapter 2
Site Planning
Rack-Mounting Guidelines
The following sections provide guidelines for rack-mounting the Cisco ASR 903 Router:
Precautions for Rack-Mounting, page 2-18
Rack Selection Guidelines, page 2-18
Equipment Rack Guidelines, page 2-19
Precautions for Rack-Mounting

The following rack-mount guidelines are provided to ensure your safety:
Do not move large racks by yourself. Due to the height and weight of a rack, a minimum of two
people are required to accomplish this task.
Ensure that the rack is level and stable before extending a component from the rack.
Ensure that proper airflow is provided to the components in the rack.
Do not step on or stand on any component or system when servicing other systems or components
in a rack.
When mounting the Cisco ASR 903 Router in a partially filled rack, load the rack from the bottom
to the top, with the heaviest component at the bottom of the rack.
If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing
the unit in the rack.
Rack Selection Guidelines

The Cisco ASR 903 Router can be mounted in most two-post or four-post, 19-inch equipment racks that
comply with the Electronic Industries Association (EIA) standard for equipment racks (EIA-310-D
19-inch). The rack must have at least two posts with mounting flanges to mount the chassis.
Caution
When mounting a chassis in any type of rack equipment, ensure that the inlet air to the chassis does not
exceed 65C.
The distance between the center lines of the mounting holes on the two mounting posts must be 18.31
inches 0.06 inch (46.50 cm 0.15 cm). The rack-mounting hardware included with the chassis is
suitable for most 19-inch equipment racks.
Consider installing the Cisco ASR 903 Router in a rack with the following features:
Network Equipment Building System (NEBS) compliant, 19-inch (48.3 cm) wide rack.
EIA or European Telecommunications Standards Institute (ETSI) hole patterns in the mounting
rails. The required mounting hardware is shipped with the Cisco ASR 903 Router. If the rack that
you plan to install the system in has metric-threaded rails, you must provide your own
metric-mounting hardware.
Perforated top and open bottom for ventilation to prevent overheating.
Leveling feet for stability.
2-18
OL-25178-08
Chapter 2

Site Planning
Note
The Cisco ASR 903 Router should not be installed in an enclosed rack because the chassis requires an
unobstructed flow of cooling air to maintain acceptable operating temperatures for its internal
components. Installing the router in any type of enclosed rackeven with the side doors
removedcould disrupt the air flow, trap heat next to the chassis, and cause an overtemperature
condition inside the router. If you use an enclosed rack, ensure that there are air vents on all sides of the
rack and there is proper ventilation.
Equipment Rack Guidelines

The placement of the rack can affect personnel safety, system maintenance, and the systems ability to
operate within the environmental characteristics described in the Cisco ASR 900 Series Aggregation
Services Routers Data Sheet.
Choose a proper location for the Cisco ASR 903 Router by following the following guidelines.
Locating for Safety

If the Cisco ASR 903 Router is the heaviest or the only piece of equipment in the rack, consider
installing it at or near the bottom to ensure that the racks center of gravity is as low as possible.
For additional information about the proper placement of electronic equipment, consult the document
GR-63-CORE, Network Equipment Building System (NEBS) Requirements: Physical Protection.
Locating for Easy Maintenance

Keep at least 3 feet of clear space at the front and back of the rack. This space ensures that you can
remove the Cisco ASR 903 Router components and perform routine maintenance and upgrades easily.
Avoid installing the Cisco ASR 903 Router in a congested rack and consider how routing of cables from
other pieces of equipment in the same rack could affect access to the router cards.
The sides of the chassis must remain unobstructed to ensure adequate airflow and prevent overheating
inside the chassis.
Allow the following clearances for normal system maintenance:
At the top of the chassisAt least 3 inches (7.6 cm)
Sides of the chassis3 to 4 ft (91.44 cm to 121.92 cm)
To avoid problems during installation and ongoing operations, follow these general precautions when
you plan equipment locations and connections:
Use the show environment all command regularly to check the internal system status. The
environmental monitor continually checks the interior chassis environment; it provides warnings
about high temperature and creates reports on other potentially dangerous occurrences. If warning
messages are displayed, take immediate action to identify the cause, and correct the problem.
Keep the Cisco ASR 903 Router off the floor and out of areas that collect dust.
Follow ESD-prevention procedures to avoid damage to equipment. Damage from static discharge
can cause immediate or intermittent equipment failure.

OL-25178-08
2-19
Chapter 2
Site Planning
Locating for Proper Airflow

Ensure that the Cisco ASR 903 Router location has enough airflow to keep the system operating within
the environmental characteristics and the air temperature is sufficient to compensate for the heat
dissipated by the system. For more information, see Air Flow Guidelines section on page 2-13.
Installation Checklist
To assist you with your installation and to provide a record of what was done by whom and when,
photocopy the Cisco ASR 903 Router Installation Checklist shown in Table 2-1. Use this to record the
completion and verification of each procedure. After the checklist is completed, place it in your Site Log
along with the other records pertaining to your new Cisco router.
Table 2-1
Cisco ASR 903 Router Installation Checklist
Verified
By
Task
Date
Date on which chassis received

Chassis and all accessories unpacked
Types and numbers of interfaces verified
Safety recommendations and guidelines reviewed
Installation Checklist copied
Site Log established and background information entered
Site power voltages verified
Site environmental specifications verified
Required passwords, IP addresses, device names, and so on, available
Required tools available
Network connection equipment available
Cable-management brackets installed (optional, but recommended)
AC power cables connected to AC sources and router
DC power cables connected to DC sources and router
Network interface cables and devices connected
System power turned on
System boot complete (STATUS LED is on)
Shared port adapters are operational
Correct software configuration displayed after system banner appears
2-20
OL-25178-08
Chapter 2

Receiving the Cisco ASR 903 Router
Creating a Site Log

The Site Log provides a record of all the actions related to installing and maintaining the router. Keep it
in an accessible place near the chassis so that anyone who performs tasks has access to it.
Create the Site Log prior to the installation. (See Appendix A, Site Log and Manufactures for more
information on the Site Log as well as a sample Site Log that can be used to make copies.)

Each Cisco ASR 903 Router chassis is shipped in a container. See Figure 2-2.
Figure 2-2
Cisco ASR 903 Router Packaged for Shipping
3
4
5
391887
Cap of Accessories tray
Packaging Material
Accessories tray
Packaging Material
Cisco ASR 903 router
Packaging Container

OL-25178-08
2-21
Chapter 2
Chassis-Lifting Guidelines
The chassis is not intended to be moved frequently. Before you install the system, ensure that your site
is properly prepared so that you can avoid having to move the chassis later to accommodate power
sources and network connections.
Each time you lift the chassis, follow these guidelines:
Warning
Ensure that your footing is solid, and balance the weight of the chassis between your feet.
Lift the chassis slowly; never move suddenly or twist your body as you lift.
Keep your back straight and lift with your legs, not your back. If you must bend down to lift the
chassis, bend at the knees, not at the waist, to reduce the strain on your back muscles.
Do not remove installed components from the chassis.
Always disconnect all external cables before lifting or moving the chassis.
Do not carry the chassis in any other packaging except as provided by Cisco packaging. Usage of
other inferior packaging for equipment movement may cause severe damage to the product.
If the equipment is opened for testing purposes, and has to be re-packaged for movement, package
it exactly the same way (orientation) as it was previously packaged at the time of product delivery
by including all the packaging counter parts. Wrong orientation may cause damage to the product
during transportation.
Always use ESD cover to wrap the hardware before packing it into packaging carton.
If faulty hardware has to be shipped to RMA depot, use same Cisco packaging which was provided
at the time of product delivery.
To prevent personal injury or damage to the chassis, never attempt to lift or tilt the chassis using the
handles on modules (such as power supplies, fans, or cards); these types of handles are not designed
to support the weight of the unit. Lift the unit only by using handles that are an integral part of the
chassis, or by grasping the chassis underneath its lower edge. Statement 163
Tools and Equipment

You need the following tools and equipment to install and upgrade the router and its components:
ESD-preventive cord and wrist strap
Antistatic mat or antistatic foam
Number 1 and Number 2 Phillips-head screwdrivers
Flat-blade screwdrivers: Small 3/16-inch (0.476 cm) and medium 1/4-inch (0.625 cm):
To install or remove modules
To remove the cover if you are upgrading the memory or other components
#12-24 pan-head screws to secure the router to the equipment rack
Cables for connecting to the WAN and LAN ports (depending on the configuration)
2-22
OL-25178-08
Chapter 2

Note
Warning
For more information on cable specifications, see Chapter 4, Troubleshooting.
Ethernet hub or switch or PC with a network interface card for connecting to the Ethernet ports
Console terminal (an ASCII terminal or a PC running terminal emulation software) that is
configured for 9600 baud, 8 data bits, no parity, and 2 stop bits
Console cable for connecting to the console port
(Optional) Modem for connecting to the auxiliary port for remote administrative access
Auxiliary cable for connecting to the auxiliary port (you can supply this cable or order one)
Ratcheting torque screwdriver with a Phillips head that exerts up to 30 pound-force per square inch
(in-lb) of pressure
Crimping tool as specified by the ground lug manufacturer
18 AWG copper wire for the power cord
Wire-stripping tools for stripping both 6 AWG and 18 AWG wire
Tape measure and level
Only trained and qualified personnel should be allowed to install or replace this equipment.
Statement 49
Unpacking and Verifying the Shipped Contents

When you receive your chassis, perform the following steps and use the Shipping Contents Checklist:
Table 2-2
Step 1
Inspect the box for any shipping damage. If there is obvious physical damage, contact your Cisco service
representative.
Step 2
Unpack the Cisco ASR 903 Router.
Step 3
Perform a visual inspection of the chassis.
Step 4
Use Table 2-2 to check the contents of the Cisco ASR 903 Router shipping container. Do not discard the
shipping container. You will need the container if you move or ship the Cisco ASR 903 Router in the
future.
Cisco ASR 903 Router Shipping Container Contents
Component
Description
Chassis
Cisco ASR 903 Router chassis

Fan tray
Power supplies
RSP
Interface modules

OL-25178-08
2-23
Chapter 2
Table 2-2
Cisco ASR 903 Router Shipping Container Contents (continued)
Component
Description
Accessories kit
Chassis rack-mount brackets (19-inch EIA)

Three sets of screws:
Front and rear rack-mount bracket screws (2 sets)
Cable-management bracket screws
Six cable-management brackets (one per bracket)

One earth lug with two 10-32 screws.
1 RJ45 to RJ45 crossover cable
1 RJ45 to DB-9 (female) adapter
ESD, wrist strap (disposable)
One disposable wrist strap (optional)
Documentation
Regulatory Compliance and Safety Information for the Cisco ASR 903 Router
Optional equipment
Check the container for the following optional equipment:
Note
Power cord if an AC power supply was shipped. There are no cords for the DC
power supply units.
T1/E1 cable connector (required only for T1/E1 interface modules)
Most Cisco documentation is available online. Documentation that is shipped with your
Cisco ASR 903 Router includes the Regulatory Compliance and Safety Information for the
Cisco ASR 903 Router document, and the Cisco ASR 903 Router Documentation Roadmap that contains
information about the various documents that are available online and the links to them.
2-24
OL-25178-08
CH A P T E R

This chapter describes how to install the Cisco ASR 903 Router and includes the following sections:
Prerequisites, page 3-1
Installing the Router in a Rack, page 3-1
Installing the Chassis Ground Connection, page 3-8
Installing the Fan Tray, page 3-11
RSP Installation, page 3-15
Interface Module Installation, page 3-18
Installing the Power Supply, page 3-22
Connecting the Cisco ASR 903 Router to the Network, page 3-36
Prerequisites
Before installing the Cisco ASR 903 Router, it is important to prepare for the installation by:
Preparing the site (site planning) and reviewing the installation plans or method of procedures
(MOP)
Unpacking and inspecting the Cisco ASR 903 Router
Gathering the tools and test equipment required to properly install the Cisco ASR 903 Router
For more instructions on how to prepare for the installation of the Cisco ASR 903 Router, see Chapter 2,
Preparing for Installation.
Installing the Router in a Rack

The following sections describe how to install the Cisco ASR 903 Router in a rack:
Installing the Chassis Brackets, page 3-2
Installing the Router Chassis in the Rack, page 3-3
Attaching the Cable Management Brackets, page 3-6

OL-25178-08
3-1
Chapter 3
Installing the Chassis Brackets

The chassis is shipped with mounting brackets that can be installed on the front or rear of the chassis.
To install the brackets on the front of the chassis, perform these steps:
Step 1
Remove the rack-mount brackets from the accessory kit and position them beside the router chassis.
Figure 3-1 shows how to attach the brackets on the Cisco ASR 903 Router for a 19-inch EIA rack.
Attaching Mounting Brackets for a 19-inch EIA Rack
209338
Figure 3-1
Figure 3-2 shows how to attach the brackets on the Cisco ASR 903 Router for a 300 mm ETSI cabinet.
Attaching Mounting Brackets for a 300 mm ETSI Cabinet
209247
Figure 3-2
Step 2
Position one of the brackets against the chassis side, and align the screw holes.
Step 3
Secure the bracket to the chassis with the screws removed when performing Step 1. The recommended
maximum torque is 28 in.-lb (3.16 N-m).
3-2
OL-25178-08
Chapter 3

Note
Step 4
The A903-FAN-E fan tray with filter (A903-FAN-F) cannot be mounted using the mounting screws that
are supported for A903-FAN fan tray. This is not an issue with the FAN tray filter blank panel
(A903-FAN-F-B). We recommend that you use the short screws provided in the following rack mount
kits to avoid interference of the air filter during rack mounting and while replacing the fan tray
(A903-FAN) with the fan tray (A903-FAN-E):
19" rack mount kit (A903-RCKMT-19IN)
ETSI rack mount kit (A903-RCKMT-ETSI)
Repeat Step 2 and Step 3 for the other bracket.
Installing the Router Chassis in the Rack

The procedures in this section apply to both horizontal and vertical mounting of the router in a rack.
To install the router chassis in the equipment rack, perform these steps:
Step 1
Step 2
Caution
Position the chassis in the rack as follows:
If the front of the chassis (front panel) is at the front of the rack, insert the rear of the chassis between
the mounting posts.
If the rear of the chassis is at the front of the rack, insert the front of the chassis between the
mounting posts.
Align the mounting holes in the bracket (and optional cable guide) with the mounting holes in the
equipment rack.
Do not use interface module and power supply ejector handles to lift the chassis; using the handles to
lift the chassis can deform or damage the handles.
Installing the Chassis in a 19-inch EIA Rack
209248
Figure 3-3

OL-25178-08
3-3
Chapter 3
Installing the Chassis to support the Japanese JIS Rack Standard
Figure 3-5
Installing the Chassis in a 300 mm ETSI Cabinet
209246
343345
Figure 3-4
3-4
OL-25178-08
Chapter 3

Figure 3-6
Vertical Mounting Installation
GE-0
GE-1
GE-2
GE-3
GE-4
GE-5
GE-6
7 S
7 S
7 S
GE-7
GE-7
GE-6
GE-5
GE-4
GE-3
GE-2
GE-1
GE-0
GE-7
GE-6
GE-5
GE-4
GE-3
GE-2
GE-1
GE-0
PWR
STAT
PWR
STAT
PWR
STAT
PWR
STAT
PWR
STAT
PWR
STAT
RUDY RSP
INPUT
OK
OUTPUT
FAIL
MEM
CONSOLE
24V60V
1PPS
IN
28A
1PPS
OUT
1OMHZ
IN
1OMHZ
OUT
INPUT
OK
OUTPUT
FAIL
TOD
BITS
MGMT
ENET
24V60V
SYNC
FAN TEMP
CRIT MAJ MIN
ALARM
391886
ACT
PWR
STAT
28A
Note
During vertical installation of the router, ensure that the equipment is mounted only on concrete or other
non-combustible surfaces.
Step 3
Install the 8 or 12 (4 or 6 per side) 12-24 x 3/4-inch or 10-32 x 3/4-inch screws through the holes in the
bracket and into the threaded holes in the equipment rack posts.
Step 4
Use a tape measure and level to verify that the chassis is installed straight and level.

OL-25178-08
3-5
Chapter 3
Installing the Chassis in the Air Plenum

Note
Ensure that the router is not installed in the Air Plenum while mounting it on the rack.
For instructions on mounting the air plenum on the rack, (see Table A-2).
Step 1
Position the chassis so that the rear of the chassis is at the front of the plenum. See Figure 3-7.
Step 2
Slide the chassis into the plenum so that the front of the chassis is in flush with the mounting rails and
brackets.
Figure 3-7
Cisco ASR 903 Chassis with Air Plenum
361017
Cisco ASR 903 router
Air plenum
Attaching the Cable Management Brackets

The router supports the following brackets:
Note
A903-CABLE-GUIDE (See Figure 3-8)
A903-CAB-BRACKETThis bracket helps in routing the cables from the interface modules;
therefore enabling a proper cable bending radius. See Figure 3-9.
The mounting brackets and cable mounting brackets are assembled together. We recommend that the
brackets are installed before the chassis is installed in the Air Plenum.
3-6
OL-25178-08
Chapter 3

To install the optional cable management brackets, perform these steps:

Position the cable management brackets against the front of the chassis and align the four screw holes,
as shown in Figure 3-8.
Figure 3-8
Cable Management Bracket Installation
Figure 3-9
Cable Management Bracket (A903-CAB-BRACKET)
361015
282406
Step 1
1
Step 2
Secure the cable management brackets with four M4 screws. The recommended maximum torque is 10
in.-lb (1.12 N-m).

OL-25178-08
3-7
Chapter 3

Before you connect the power or turn on the power to the Cisco ASR 903 Router, you must provide an
adequate chassis ground (earth) connection to your router.
This section describes how to ground the Cisco ASR 903 Router chassis. The router provides two
locations for attaching a 2-hole grounding lug according to the rack-mounting brackets you use to install
the router. The Cisco ASR 903 Router supports the following rack-mounting types:
EIA 19-inch rackAttach the grounding lug to the rear of the router, as shown in Figure 3-10.
Figure 3-10
Attaching a Grounding Lug to the Rear of the Router
281928
Grounding lug (19-inch EIA rack)

300 mm ETSI cabinetAttach the grounding lug on the rack-mount bracket on the front of the
router, as shown in Figure 3-11.
Figure 3-11
Attaching a Grounding Lug to the Rack-Mount Bracket
1
GE-0
GE-1
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
GE-0
GE-1
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
PWR
FAN TEMP
STAT
CRIT MAJ MIN
PWR
STAT
GE-0
GE-1
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
PWR
RUDY RSP
STAT
SYNC
ACT
PWR
MEM
CONSOLE
1PPS
IN
1PPS
OUT
1OMHZ
IN
1OMHZ
OUT
STAT
L
PWR
TOD
BITS
MGMT
ENET
STAT
24V60V
28A
7 S
PWR
STAT
L
7 S
7 S
PWR
INPUT
OK
OUTPUT
FAIL
24V60V
28A
INPUT
OK
OUTPUT
FAIL
ALARM
281929
STAT
Grounding lug (300 mm ETSI cabinet)
3-8
OL-25178-08
Chapter 3

To ensure that the chassis ground connection that you provide is adequate, you need the following parts
and tools:
Ratcheting torque screwdriver with Phillips head that exerts up to 15 in.-lb (1.69 N-m) of pressure
for attaching the ground wire to the router
Crimping tool as specified by the ground lug manufacturer
18 AWG copper wire for the power cord
6 AWG or larger copper wire for the ground wire
Wire-stripping tools appropriate to the wire you are using
Caution
Before making connections to the Cisco ASR 903 Router, ensure that you disconnect the
power at the circuit breaker. Otherwise, severe injury to you or damage to the router may
occur.
Warning
This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection
authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024
Warning
Use copper conductors only. Statement 1025
Warning
When installing the unit, the ground connection must always be made first and disconnected last.
Statement 42
This unit is to be installed in a restrictive access location and must be permanently grounded to minimum
6 AWG copper ground wire.
Perform the following procedure to ground the Cisco ASR 903 Router using a 2-hole lug and the
corresponding mounting point. Most carriers require a minimum 6 AWG ground connection. Verify your
carriers requirements for the ground connection.
Step 1
If your ground wire is insulated, use a wire-stripping tool to strip the ground wire to 0.5 inch 0.02 inch
(12.7 mm 0.5 mm) (Figure 3-12).
Figure 3-12
Stripping a Ground Wire
Insulation
Step 2
Wire lead
60528
0.5 in. (12.7 mm) 0.02 in. (0.5 mm)
Slide the open end of your 2-hole ground lug over the exposed area of the ground wire.

OL-25178-08
3-9
Chapter 3
Step 3
Using a crimping tool (as specified by the ground lug manufacturer), crimp the ground lug to the ground wire
as shown in Figure 3-13.
Crimping a Ground Lug onto the Ground Wire
60529
Figure 3-13
Step 4
Use a Phillips head screwdriver to attach the 2-hole ground lug and wire assembly to the router with the
2 pan-head Phillips head screws. For a 19-inch EIA rack, attach the 2-hole ground lug to the rear of the
router.
Step 5
Connect the other end of the ground wire to a suitable grounding point at your site.
3-10
OL-25178-08
Chapter 3

Installing the Fan Tray

The fan tray is a modular unit that provides cooling to the Cisco ASR 903 Router. Follow these steps to
install the fan tray in the chassis:
Step 1
Orient the fan tray so that the captive screws are on the left side of the fan trays front panel. Figure 3-14
shows how to orient the fan tray.
Figure 3-14
GE-0
GE-1
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
PWR
STAT
GE-0
GE-1
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
GE-0
GE-1
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
PWR
STAT
FAN TEMP
PWR
RUDY RSP
STAT
SYNC
CRIT MAJ MIN
ACT
PWR
MEM
CONSOLE
1PPS
IN
1PPS
OUT
1OMHZ
IN
1OMHZ
OUT
STAT
L
7 S
7 S
7 S
PWR
TOD
BITS
MGMT
ENET
STAT
24V60V
28A
PWR
PWR
STAT
INPUT
OK
OUTPUT
FAIL
24V60V
28A
INPUT
OK
OUTPUT
FAIL
ALARM
Step 2
Guide the fan tray into the chassis until it is fully seated.
The fans are exposed on the left side of the fan tray. Keep your fingers, clothing, and jewelry
away from the fans. Always handle the fan tray by the handle.
Caution
Note
Step 3
281934
STAT
When installing the cabling to the RSPs, we recommend that you leave a service loop of extra
cabling sufficient to allow for fan tray removal.
Secure the fan tray to the chassis using the attached captive installation screws. The recommended
maximum torque is 5.5 in.-lb (.62 N-m).
This completes the procedure for installing or replacing the fan tray in a Cisco ASR 903 Router.
For information about connecting cables to the fan tray alarm port, see Connecting the Fan Tray Alarm
Port section on page 3-54. For a summary of the LEDs on the fan tray, see LED Summary section on
page 4-13. For more information about air flow guidelines, see Air Flow Guidelines, page 2-13.
Installing the Dust Filter

Step 1
Follow the steps for removing the fan tray (if installed) from the chassis. See Removing and Replacing
the Fan Tray, page 3-13
Step 2
Remove the dummy cover from the fan tray. See Figure 1-7.

OL-25178-08
3-11
Chapter 3
Step 3
Slide the dust filter onto the fan tray. See Figure 1-7.
Step 4
Insert the dummy cover on the fan tray to secure the filter within the chassis.
Step 5
Follow the steps to install the fan tray in the chassis. See Installing the Fan Tray, page 3-11.
Removing the Dust Filter

The dust filter must be removed for cleaning or for a replacement.
Dust Filter Maintenance

A periodic health check of the filter, every 3 months based on the level of dust in the environment helps
in avoiding over clogging of the filters and provide better life. The product's filter may be used as a single
use or reused depending upon the local deployment needs. If reuse of the filter is prohibited, it may be
replaced every six months with PID (A903-FAN-F=) or equivalent.
If reused, this filter media may be cleaned with slightly compressed air, vacuumed, and/or rinsed with
clean water. If a degreaser is required, use only a mild detergent, such as, dish washing liquid.
Caution
Avoid using harsh solvents or cleaning agents.

If filters are cleaned with water, the filters should be completely dry before reinstalling. Even though
this type of filter may be cleaned, replacement is recommended every two to three years to ensure media
durability and eliminate residual dust build-up and subsequent air flow resistance.
Step 1
Remove the dummy cover from the fan tray.
Step 2
Remove the dust filter from the fan.
Note
The filter can be accessed by pulling the pull tab by using fingers or pliers. See Figure 1-7.
Step 3
Slide the replacement dust filter onto the fan tray
Step 4
Insert the dummy cover onto the fan tray to secure the filter within the chassis.
3-12
OL-25178-08
Chapter 3

Removing and Replacing the Fan Tray

The fan tray supports online insertion and removal (OIR). There is no need to power down the
Cisco ASR 903 Router to remove or replace the fan tray. However, there is a finite time to replace the
fan tray. This time depends upon the specific RSP and fan tray combination and also the ambient
temperature. The following table provides the time interval for replacing the fan tray. At higher ambient
temperatures, the replacement time is lower.
Table 3-1
Caution
Fan Tray Replacement Time
RSP Module
Fan Tray
Replacement Time at 25C

Ambient
RSP1, RSP2
A903-FAN, A903-FAN-E
5 minutes
RSP3
A903-FAN, A903-FAN-E
1 minute
To avoid erroneous failure messages, allow at least 2 minutes for the system to reinitialize after the fan
tray has been removed or replaced.
Follow these steps to remove and replace the fan tray on the Cisco ASR 903 Router:
Step 1
Using a No. 2 Phillips screwdriver or your fingers, loosen the captive installation screw that secures the
fan tray to the chassis. Figure 3-15 shows the front of the fan tray, including the captive installation
screws.
Figure 3-15
Captive
installation
screw
Detaching the Fan Tray
FAN TEMP
CRIT MAJ MIN
Handle
209393
ALARM
Step 2
Grasp the fan tray handle with one hand and the outside of the chassis with the other hand. Figure 3-15
shows the front of the fan tray, including the handle.

OL-25178-08
3-13
Chapter 3
The fans are exposed on the left side of the fan tray. Keep your fingers, clothing, and jewelry
away from the fans. Always handle the fan tray by the handle.
Caution
Step 3
Pull the fan tray backward toward you no more than 1 inch to disengage it from the power receptacle on
the midplane, as shown in Figure 3-16.
Figure 3-16
Fan Tray Removal
FAN TEMP
SYNC
CRIT MAJ MIN
ACT
PWR
TOD
BITS
MGMT
ENET
STAT
24V60V
28A
209394
ALARM
Warning
Step 4
When removing the fan tray, keep your hands and fingers away from the spinning fan
blades. Let the fan blades completely stop before you remove the fan tray. Statement 258
Wait at least 5 seconds to allow the fans to stop spinning. Then, pull the fan tray backward toward you
and out of the chassis.
Note
As the fan tray slides out of the chassis, support the bottom of the fan tray with one hand and
keep your other hand on the fan tray handle.
This completes the steps for removing the fan tray from the chassis.
To install the new fan tray, follow the steps in Installing the Fan Tray section on page 3-11.
3-14
OL-25178-08
Chapter 3

RSP Installation
RSP Installation
Follow these steps on handling an RSP module in the Cisco ASR 903 Router:
Installing an RSP Module, page 3-15
Removing an RSP Module, page 3-16
Hot-Swapping an RSP Module, page 3-17
Installing an RSP Module

To install an RSP module in the router chassis, perform the following steps:
Step 1
Choose a slot for the module. Make sure that there is enough clearance to accommodate any equipment
that will be connected to the ports on the module. If a blank module filler plate is installed in the slot in
which you plan to install the module, remove the plate by removing its 2 Phillips pan-head screws.
Step 2
Fully open both the ejector levers on the new module, as shown in Figure 3-17.
Caution
Step 3
To prevent ESD damage, handle modules by carrier edges only.
Position the module in the slot. Make sure that you align the sides of the module with the guides on each
side of the slot, as shown in Figure 3-17.
Figure 3-17
Cisco ASR 903 Router RSP Installation
GE-0
GE-0
GE-0
GE-0
GE-0
RUDY RSP
GE-0
GE-1
GE-1
GE-1
GE-1
GE-1
GE-1
GE-2
GE-2
GE-2
GE-2
GE-2
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
PWR
GE-3
GE-4
GE-5
STAT
GE-6
GE-7
PWR
GE-3
GE-4
GE-5
STAT
GE-6
GE-7
FAN TEM
P
PWR
GE-3
GE-4
GE-5
STAT
GE-6
CRIT MAJ
MIN
GE-7
PWR
GE-3
GE-4
GE-5
STAT
GE-6
GE-7
PWR
GE-3
GE-4
GE-5
STAT
GE-6
GE-7
PWR
CONSOLE
1PPS
IN
INPUT
OK
STAT
1PPS
OUT
1OMHZ
IN
OUTPUT
FAIL
1OMHZ
OUT
SYNC
ACT
TOD
BITS
Step 4
MGMT
ENET
PWR
STAT
24V60V
28A
INPUT
OK
OUTPUT
FAIL
24V60V
28A
ALARM
281932
MEM
Carefully slide the module into the slot until the EMI gasket on the module makes contact with the
module in the adjacent slot and both the ejector levers have closed to approximately 45 degrees with
respect to the module faceplate.
Caution
If the top slot already has an RSP module installed, and you install a second RSP module in
the slot below it, be careful not to damage the EMI gasket of the bottom RSP module against
the ejector levers of the top RSP during insertion.

OL-25178-08
3-15
Chapter 3
RSP Installation
Step 5
While pressing down, simultaneously close both the ejector levers to fully seat the module in the
backplane connector. The ejector levers are fully closed when they are flush with the module faceplate.
Step 6
Tighten the two captive installation screws on the module. The recommended maximum torque is 5.5
in.-lb (.62 N-m).
Note
Step 7
Make sure that the ejector levers are fully closed before tightening the captive installation
screws.
Verify that the captive installation screws are tightened on all of the modules installed in the chassis.
This step ensures that the EMI gaskets on all the modules are fully compressed in order to maximize the
opening space for the new or replacement module.
Note
If the captive installation screws are loose, the EMI gaskets on the installed modules will push
adjacent modules toward the open slot, which reduces the size of the opening and makes it
difficult to install the new module.
Note
Blank module filler plates (Cisco part number A900-RSPA-BLANK) should be installed in any empty
chassis slots to keep dust out of the chassis and to maintain consistent airflow through the chassis.
Note
When installing the cabling to an RSP, we recommend that you leave a service loop of extra cabling
sufficient to allow for fan tray removal.
Note
Close all unused RJ-45 and USB ports on the RSP module using the appropriate dust caps to prevent dust
from accumulating inside the cage. For information on dust caps, see Installing Dust Caps, page 3-38.
Removing an RSP Module

Before you remove an RSP from the router, you should save the current configuration using the write
{host file | network | terminal} command. This saves you time when bringing the module back online.
If the module is running Cisco IOS software, save the current running configuration by entering the copy
running-config startup-config command.
Warning
Hazardous voltage or energy is present on the backplane when the system is operating. Use caution
when servicing. Statement 1034
Warning
To remove an RSP module, perform the following steps:

Step 1
Disconnect any cables attached to the ports on the module.
3-16
OL-25178-08
Chapter 3

RSP Installation
Step 2
Verify that the captive installation screws on all the modules in the chassis are tight. This step ensures
that the space created by the removed module is maintained.
If the captive installation screws are loose, the EMI gaskets on the installed modules will push
the modules toward the open slot, which in turn reduces the size of the opening and makes it
difficult to remove the module.
Note
Step 3
Loosen the two captive installation screws on the module you plan to remove from the chassis.
Step 4
Place your thumbs on the ejector levers (see Figure 3-17) and simultaneously rotate the ejector levers
outward to unseat the module from the backplane connector.
Step 5
Grasp the front edge of the module and slide the module straight out of the slot. If the chassis has
horizontal slots, place your hand under the module to support its weight as you slide it out from the slot.
Do not touch the module circuitry.
Caution
To prevent ESD damage, handle modules by the carrier edges only.
Step 6
Place the module on an antistatic mat or antistatic foam, or immediately reinstall the module in another
slot.
Step 7
Install blank module filler plates (Cisco part number A900-RSPA-BLANK) in empty slots, if any.
Warning
operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement
1029
Hot-Swapping an RSP Module

The Cisco ASR 903 Router provides a feature that allows you to remove and replace a redundant RSP
module without powering down the router. This feature, called hot-swapping or OIR, allows you to
remove and replace a redundant module without disrupting router operation.
When two redundant modules are installed in the router, only one of the modules is active. The other one
runs in standby mode, ready to take over processing if the active module fails.
When you remove or insert a redundant module while the router is powered on and running, the router
does the following:
1.
Determines if there is sufficient power for the module.
2.
Scans the backplane for configuration changes.
3.
Initializes the newly inserted module. In addition, the system notes any removed modules and places
those modules in the administratively shutdown state.
4.
Places any previously configured interfaces on the module back to the state they were in when they
were removed. Any newly inserted interfaces are put in the administratively shutdown state as if they
were present (but unconfigured) at boot time. If you insert the same type of module into a slot, its
ports are configured and brought online up to the port count of the original module.
The router runs diagnostic tests on any new interfaces and the test results indicate the following:

OL-25178-08
3-17
Chapter 3
Interface Module Installation
If the tests pass, the router is operating normally.
If the new module is faulty, the router resumes normal operation but leaves the new interfaces
disabled.
If the diagnostic tests fail, the router stops operating, which usually indicates that the new module
has a problem in the bus and should be removed.

The following sections describe the various tasks of associated with interface module installation on the
Cisco ASR 903 Router:
Installing an Interface Module, page 3-18
Removing an Interface Module, page 3-19
Hot-Swapping an Interface Module, page 3-19
Installing an Interface Module

Step 1
Before inserting an interface module, make sure that the chassis is grounded.
Step 2
To insert the interface module, carefully align the edges of the interface module between the upper and
lower edges of the router slot.
Step 3
Carefully slide the interface module into the router slot until the interface module makes contact with
the backplane. Figure 3-18 shows how to install the interface module.
Inserting an Interface Module
282442
Figure 3-18
Step 4
Tighten the locking thumbscrews on both sides of the interface module. The recommended maximum
torque is 5.5 in.-lb (.62 N-m).
Step 5
Connect all the cables to each interface module.
3-18
OL-25178-08
Chapter 3

Note
Close all unused SFP ports using SFP dust caps to prevent dust from accumulating inside the cage. The
dust caps (Cisco part number A900-DCAP-SFP-S= (24 caps per package) or Cisco part number
A900-DCAP-SFP-L= (240 caps per package)) can be ordered from Cisco.
Note
10 Gigabit Ethernet interface modules on the A900-RSP1 modules and A900-RSP2A-64 module are not
supported in slots 4 and 5.
Note
Close all unused RJ-45, SFP, XFP, and QSFP ports on the interface module using the appropriate dust
caps to prevent dust from accumulating inside the cage. For information on dust caps, see Installing Dust
Caps, page 3-38.
Caution
Removing an Interface Module

Step 1
To remove an interface module, disconnect all the cables from each interface module.
Step 2
Loosen the locking thumbscrews on both sides of the interface module.
Step 3
Slide the interface module out of the router slot by pulling on the handles. If you are removing a blank
filler plate, pull the blank filler plate completely out of the router slot using the captive screws.
Hot-Swapping an Interface Module

The Cisco ASR 903 Router provides a feature that allows you to remove and replace an interface module
without powering down the router. This feature, called hot-swapping or OIR, allows you to remove and
replace a redundant module without disrupting router operation.
Use the following guidelines when performing an OIR on an IM:
Note
Allow at least 2 minutes for the system to reinitialize before inserting a new IM.
Avoid inserting a new IM during bootup until the active and standby RSPs have reached an OK state.
When inserting multiple IMs into the chassis, wait until each IM reaches an OK state before
inserting the next IM.
The following interface modules take around 60 to 70 seconds to reach OK state after a soft OIR is
performed:
Copper Combo IM8-port Gigabit Ethernet (8X1GE) + 1-port 10 Gigabit Ethernet Interface
Module(1X10GE) (PN:A900-IMA8T1Z)

OL-25178-08
3-19
Chapter 3
Note
Note
SFP Combo IM8-port Gigabit Ethernet (8X1GE) + 1-port 10 Gigabit Ethernet (1X10GE)
(PN:A900-IMA8S1Z)
2-port 10 Gigabit Ethernet Interface Module(2X10GE) (PN:A900-IMA2Z)
The A900-RSP1 RSP module does not support hot-swapping an interface module with another module
of a different type . For example, you cannot swap an SFP Gigabit Ethernet module with a copper Gigabit
Ethernet module without disrupting router operation.
The router does not support swapping of the TDM interface modules to Gigabit Ethernet modules
on the Cisco ASR 900 Series Router and vice-versa.
If the TDM interface module is swapped with the Gigabit Ethernet module in the same slot or
vice-versa, the router must be reloaded.
If you perform OIR on an interface module and move the module to a different slot, the router does not
retain the module configuration; you must reconfigure the interface module.
Replacing a configured interface module with a different interface module in the same slot is not
supported on the router.
When you remove or insert a redundant module while the router is powered on and running, the router
does the following:
1.
Determines if there is sufficient power for the module.
2.
Scans the backplane for configuration changes.
3.
Initializes the newly inserted module. In addition, the system notes any removed modules and places
those modules in the administratively shutdown state.
4.
Places any previously configured interfaces on the module back to the state they were in when they
were removed.
The router runs diagnostic tests on any new interfaces and the test results indicate the following:
If the tests pass, the router is operating normally.
If the new module is faulty, the router resumes normal operation but leaves the new interfaces
disabled.
If the diagnostic tests fail, the router stops operating, which usually indicates that the new module
has a problem in the bus and should be removed.
Caution
To avoid erroneous failure messages, note the current configuration of all interfaces before
you remove or replace an interface module, and allow at least 2 minutes for the system to
reinitialize after a module has been removed or replaced. This time is recommended in order
to allow for synchronization between components within the interface module and for
synchronization with the standby RSP.
3-20
OL-25178-08
Chapter 3

Swapping of Interface Modules

The Ethernet interface modules support swapping on the Cisco A900-RSP2A module.
8-port Gigabit Ethernet RJ45 (Copper) Interface Module (8X1GE)
1-port 10 Gigabit Ethernet XFP Interface Module (1X10GE)
SFP Combo IM8-port Gigabit Ethernet (8X1GE) + 1-port 10 Gigabit Ethernet (1X10GE)
Copper Combo IM8-port Gigabit Ethernet (8X1GE) + 1-port 10 Gigabit Ethernet Interface
Module(1X10GE)
2-port 10 Gigabit Ethernet Interface Module(2X10GE)
Use the hw-module subslot default command before performing a swap of the modules. to default the
interfaces on the interface module.
Note
The hw-module subslot default command is not supported on the TDM and OC-3 interface
modules.
Table 3-2
Supported Hot Swapping Combinations
A900-RSP1
A900-RSP2A-64
and
A900-RSP2A-128
A900-RSP3C-400-S
Cisco IOS Release

3.14
Cisco IOS Release

3.13
Cisco IOS Release

3.16
8-port Gigabit Ethernet SFP Interface Module 1-port 10 Gigabit

(8X1GE)
Ethernet XFP
8-port Gigabit Ethernet RJ45 (Copper)
Interface Module (8X1GE)
Interface Module
(1X10GE)
SFP Combo IM8-port Gigabit Ethernet

(8X1GE) +
No support
Swapping allowed on all Ethernet

interface modules

Copper Combo IM8-port Gigabit Ethernet
(8X1GE)
No support
+ 1-port 10 Gigabit Ethernet Interface

Module(1X10GE
1-port 10 Gigabit Ethernet XFP Interface
Module (1X10GE)
8-port Gigabit
Ethernet SFP
Interface Module
(8X1GE)
8-port Gigabit
Ethernet RJ45
(Copper) Interface
Module (8X1GE)
2-port 10 Gigabit Ethernet Interface

Module(2X10GE)
No support

OL-25178-08
3-21
Chapter 3
Installing the Power Supply
Table 3-2
Note
Supported Hot Swapping Combinations
A900-RSP1
A900-RSP2A-64
and
A900-RSP2A-128

(8X10GE)
No support
No support

(1X100GE)
No support
No support
2-port 40 Gigabit Ethernet QSFP Interface

Module (2X40GE)
No support
No support
16 T1/E1
No support
No support
32 T1/E1
No support
8 T1/E1
4-Port OC3/STM-1 (OC-3) or 1-Port

OC12/STM-4 (OC-12) Interface Module
4-Port OC3/STM-1 (OC-3) or 1-Port OC12/STM-4 (OC-12)

Interface Module
A900-RSP3C-400-S
Swapping allowed
on all Ethernet
interface modules
No support
Failure in executing the command may cause the interface to enter the Out of Service state. To recover
from out of service state, perform the following:
Insert the original IM and execute the hw-module subslot 0/bay default command. Swap the
module. For more information, see Cisco IOS Interface and Hardware Component Command
Reference.
If the module does not come up, perform a reload of the router.

The Cisco ASR 903 Router router provides the choice of two different power supplies:
DC power
550 W Power Supply19.2VDC to -72VDC
The DC power supply uses 3 position terminal block-style connector with positive latching/securing
and labeled connections for +24/48V, GRD, -24/48V. The terminal block connector is of suitable
size to carry the appropriate AWG wire size to handle the input current of the power supply. No
ON/OFF switch is provided.
1200 W Power Supply40.8VDC to -72VDC
The power supplies are hot-swappable. They are enclosed to prevent exposure to high voltages, and
therefore, no power cable interlock is required. However the power supplies are automatically shut
down when removed from the chassis. The power supplies are rated to deliver 975 W (~81 A) to the
other FRUs in the system, and are rated for operation at 5C above the chassis operating temperature.
AC power
550 W Power Supply85VAC to 264VAC
3-22
OL-25178-08
Chapter 3

1200 W Power Supply85VAC to 264VAC
The AC power supply has an IEC 320-type power receptacle and a 15 Amp service connector. You
can use standard right angle power cords with the AC power supply. The power supply includes a
power cord retainer. No ON/OFF switch is provided.
Each power supply provides a single primary input power connection. You can install dual power
supplies for redundancy.
Warning
Note
Products that have an AC power connection are required to have an external surge protective device
(SPD) provided as part of the building installation to comply with the Telcordia GR-1089 NEBS
standard for electromagnetic compatibility and safety.
Caution
Do not use power supplies of different capacities together in the router for prolonged durations.
Caution
The following sections describe the Cisco ASR 903 Router power supplies:
Preventing Power Loss, page 3-23
Power Connection Guidelines, page 3-24
Installing the DC Power Supply, page 3-25
Removing and Replacing the DC Power Supply, page 3-32
Installing the AC power Supply, page 3-33
Preventing Power Loss

Use the following guidelines to prevent power loss to the router.
To prevent loss of input power, ensure that the total maximum load on each circuit supplying the
power supplies is within the current ratings of the wiring and breakers.
In some systems, you can use an UPS to protect against power failures at your site. Avoid UPS types
that use ferroresonant technology. These UPS types can become unstable with systems like the
Cisco ASR 903 Router, which can have substantial current draw fluctuations due to bursty data
traffic patterns.
Use the information in the DC Power Specifications section on page 1-3 to estimate the power
requirements and heat dissipation of a Cisco ASR 903 Router based on a given configuration of the
router. Determining power requirements is useful for planning the power distribution system needed to
support the router.

OL-25178-08
3-23
Chapter 3
Power Connection Guidelines

This section provides guidelines for connecting the Cisco ASR 903 Router power supplies to the site
power source.
Warning
Never defeat the ground conductor or operate the equipment in the absence of a suitably installed
ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are
uncertain that suitable grounding is available. Statement 213
Warning
The plug-socket combination must be accessible at all times because it serves as the main
disconnecting device. Statement 1019
Warning
This product requires short-circuit (overcurrent) protection, to be provided as part of the building
installation. Install only in accordance with national and local wiring regulations. Statement 1045
Guidelines for DC-Powered Systems

Basic guidelines for DC-powered systems include the following:
Each chassis power supply should have its own dedicated input power source. The source must
comply with the safety extra-low voltage (SELV) requirements in the UL 60950, CSA 60950, EN
60950, and IEC 60950 standards.
The circuit must be protected by a dedicated two-pole circuit breaker. The circuit breaker should be
sized according to the power supply input rating and local or national code requirements.
The circuit breaker is considered the disconnect device and should be easily accessible.
The system ground is the power supply and chassis ground.
Do not connect the DC return wire to the system frame or to the system grounding equipment.
Use the grounding lug to attach a wrist strap for ESD protection during servicing.
Guidelines for AC-Powered Systems

Basic guidelines for AC-powered systems include the following:
Each chassis power supply should have its own dedicated branch circuit.
The circuit breaker should be sized according to the power supply input rating and local or national
code requirements.
The AC power receptacles used to plug in the chassis must be the grounding type. The grounding
conductors that connect to the receptacles should connect to protective earth ground at the service
equipment.
3-24
OL-25178-08
Chapter 3

Installing the DC Power Supply

The following sections describe how to install a DC power supply in the Cisco ASR 903 Router:
Installing the DC Power Supply Module, page 3-25
Installing Terminal Block on the DC PEM Unit (A900-PWR550-D), page 3-26
Installing Terminal Block Connector on the DC PEM Unit (A900-PWR550-D-E and

A900-PWR1200-D), page 3-30
Activating the DC Power Supply, page 3-32
Note
This equipment is suitable for installation in Network Telecommunications Facilities and locations
where the NEC applies.
Note
This equipment is suitable for installations utilizing the Common Bonding Network (CBN).
Note
The grounding architecture of this product is DC-Isolated (DC-I) for DC-powered products.
DC-powered products have a nominal operating DC voltage of 48 VDC.
Installing the DC Power Supply Module

Perform the following procedure to install the power supply module:
Step 1
Ensure that the system (earth) ground connection has been made. For ground connection installation
instructions, see the Installing the Chassis Ground Connection section on page 3-8.
Step 2
If necessary, remove the blank power supply filler plate from the chassis power supply bay opening by
loosening the captive installation screws.
Step 3
Verify that power to the DC circuit connected to the power supply you are installing is off. To ensure that
power has been removed from the DC circuits, locate the circuit breakers for the DC circuits, switch the
circuit breakers to the OFF position, and tape the circuit-breaker switches in the OFF position.
Step 4
Grasp the power supply handle with one hand. Place your other hand underneath the power supply, as
shown in Figure 3-19. Slide the power supply into the power supply bay. Make sure that the power
supply is fully seated in the bay.

OL-25178-08
3-25
Chapter 3
Figure 3-19
GE-0
GE-1
Installing the DC Power Supply
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
FAN TEMP
PWR
STAT
CRIT MAJ MIN

GE-0
GE-1
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
GE-0
GE-1
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
PWR
STAT
PWR
RUDY RSP
STAT
SYNC
ACT
PWR
CONSOLE
MEM
1PPS
IN
1PPS
OUT
1OMHZ
IN
STAT
L
7 S
7 S
7 S
1OMHZ
OUT
PWR
TOD
BITS
MGMT
ENET
STAT
PWR
ALARM
PWR
STAT
INPUT
OK
OUTPUT
FAIL
Step 5
24V60V
282340
STAT
28A
Tighten the captive installation screws of the power supply. The recommended maximum torque is 5.5
in.-lb (.62 N-m).
If you are installing a redundant DC power supply, repeat these steps for the second power source.
Installing Terminal Block on the DC PEM Unit (A900-PWR550-D)

Perform the following procedure to install the terminal block.
Step 1
Locate the terminal block plug.
Step 2
Use a wire-stripping tool to strip the ends of each of the two wires coming from the DC-input power
source to 0.27 inch (6.6 mm) 0.02 inch (0.5 mm) and the wire for grounding. Do not strip more than
0.29 inch (7.4 mm) of insulation from the wire. Stripping more than the recommended amount of wire
can leave behind exposed wire from the terminal block plug after installation.
Step 3
Identify the ground, positive, and negative feed positions for the terminal block connection. The
recommended wiring sequence is (see Figure 3-20):
a.
Ground lead wire (left)
b.
Negative (-) lead wire (middle)
c.
Positive (+) lead wire (right)
3-26
OL-25178-08
Chapter 3

Figure 3-20
DC Power Supply with Lead Wires
1
2
207765
Step 4
Ground lead wire
Negative () lead wire
Positive (+) lead wire
Insert the exposed wire of one of the three DC-input power source wires into the terminal block plug.
Make sure that you cannot see any wire lead. Only wire with insulation should extend from the terminal
block.
Caution
Do not overtorque the plug captive screws of the terminal block. The recommended maximum
torque is from 4.425 in.-lb (.5 N-m) to 5.310 in-lb (.6 N-m).

OL-25178-08
3-27
Chapter 3
Step 5
Use a ratcheting torque screwdriver to torque the terminal block plug captive screw (above the installed
wire lead) from 4.425 in.-lb (.5 N-m) to 5.310 in-lb (.6 N-m) as shown in Figure 3-21.
Figure 3-21
Torquing the DC Power Supply Terminal Block Plug Screws
207764
1
Step 6
Torque is from 4.425 in.-lb (.5 N-m) to 5.310 in-lb (.6 N-m).
Repeat Step 4 through Step 5 for the remaining DC input power source wire and the ground wire.
Figure 3-22 shows the wiring completed for a terminal block plug.
Figure 3-22
Inserting the DC Power Supply Terminal Block Plug in the Block Header
FAN TEM
P
RUDY RSP
CRIT MAJ
MIN
MEM
CONSOL
E
1PPS
IN
1PPS
OUT
1OMHZ
IN
1OMHZ
OUT
SYNC
ACT
TOD
BITS
MGMT
ENET
PWR
STAT
INPUT
OK
OUTPUT
FAIL
24V60V
28A
INPUT
OK
24V60V
28A
255730
OUTPUT
FAIL
ALARM
DC power supply ground lead wire
DC power supply negative (-) lead wire
DC power supply positive (+) lead wire
3-28
OL-25178-08
Chapter 3

Caution
Secure the wires coming in from the terminal block plug so that they cannot be disturbed by
casual contact.
Step 7
Ensure that the terminal block plug is fully seated in the terminal block header on the DC power supply
panel. The plug has a locking feature. You should hear a snap or click when it is installed properly.
Step 8
Use a tie wrap to secure the wires to the rack, so that the wires are not pulled from the terminal block
plug by casual contact. Make sure the tie wrap allows for some slack in the ground wire, as shown in
Figure 3-23.
Figure 3-23
Complete DC Terminal Block Plug Insertion and Secure Tie Wrap
FAN TEM
P
RUDY RSP
CRIT MAJ
MIN
MEM
CONSOL
E
1PPS
IN
1PPS
OUT
1OMHZ
IN
1OMHZ
OUT
SYNC
ACT
TOD
BITS
MGMT
ENET
PWR
STAT
INPUT
OK
OUTPUT
FAIL
28A
INPUT
OK
OUTPUT
FAIL
24V60V
28A
255731
24V60V
ALARM
2
1
Step 9
Lead wires secured with a tie wrap
DC power supply terminal block plug being

inserted into terminal block header.
Use a tie wrap to secure the wires to the handle. Leave a service loop on the ground wire between the
handle and the connector such that it is the last to receive strain if the wires are pulled.
This completes the procedure for connecting the DC power supply in the Cisco ASR 903 Router.

OL-25178-08
3-29
Chapter 3
Installing Terminal Block Connector on the DC PEM Unit (A900-PWR550-D-E and A900-PWR1200-D)
Tools
12 AWG to 16 AWG cables
Lugs fork-type or ring-type (Burndy, see Table A-2)TP10 -6 or TP10-8F (recommended)
Step 1
Follow the steps to remove the power supply unit if installed in the chassis. See Removing and Replacing
the DC Power Supply, page 3-32.
Step 2
Locate the T-shaped terminal block plug on the DC power supply unit. See Figure 3-24.
Figure 3-24
DC PEM Module (A900-PWR550-D-E) with T-Shaped Connector
360882
T-shaped connector
Step 3
Use a wire-stripping tool to strip the ends of each of the two wires coming from the DC-input power
source to 0.27 inch (6.6 mm) 0.02 inch (0.5 mm) and the wire for grounding. Do not strip more than
0.29 inch (7.4 mm) of insulation from the wire. Stripping more than the recommended amount of wire
can leave behind exposed wire from the terminal block after installation.
Step 4
Prepare the cables by attaching the lugs to the cables.
Step 5
Identify the ground, positive, and negative feed positions for the terminal block connection (see
Figure 3-25). The recommended wiring sequence is
Negative (-) lead wire (top)
Ground lead wire (left)
Positive (+) lead wire (right)
3-30
OL-25178-08
Chapter 3

DC Power Supply Terminal Block Plug in the Block Header
391822
Figure 3-25
Step 6
DC power supply ground lead wire
DC power supply negative (-) lead wire
DC power supply positive (+) lead wire
Insert the lugged end of the cables to the connector and secure the cables using the captive screws.
The recommended torque for securing the captive screws is 0.7 N-m.
Note
Step 7
Ensure that the terminal block plug is fully seated in the terminal block header (see Figure 3-26) on the
DC power supply panel. See Installing the DC Power Supply, page 3-25 for installing the power supply
unit into the chassis
DC Terminal Block Plug Insertion
391823
Figure 3-26
Lead wires secured
DC power supply terminal block plug being

inserted into terminal block header.

OL-25178-08
3-31
Chapter 3
Activating the DC Power Supply

Perform the following procedure to activate the DC power supply:
Step 1
Remove the tape from the circuit-breaker switch handle, and restore power by moving the circuit-breaker
switch handle to the On (|) position.
Step 2
Verify power supply operation by checking if the power supply front panel LEDs are in the following
states:
INPUT OK LED is green
OUTPUT FAIL LED is green
If the LEDs indicate a power problem, see Chapter 4, Troubleshooting.

If you are installing a redundant DC power supply, ensure that each power supply is connected to a
separate power source in order to prevent power loss in the event of a power failure.
Removing and Replacing the DC Power Supply

This section provides information about removing and replacing the DC power supply in the
Note
The Cisco ASR 903 Router power supplies are hot-swappable. If you have installed redundant power
supply modules, you can replace a single power supply without interrupting power to the router.
Caution
To avoid erroneous failure messages, allow at least 2 minutes for the system to reinitialize after a power
supply has been removed or replaced.
Warning
When you install the unit, the ground connection must always be made first and disconnected last.
Statement 1046
Warning
Statement 1003
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Warning
Follow these steps to remove and replace the DC power supply on the Cisco ASR 903 Router:
3-32
OL-25178-08
Chapter 3

Step 1
Before servicing the power supply, switch off the circuit breaker in your equipment area. As an
additional precaution, tape the circuit-breaker switch in the Off position.
Step 2
Slip on the ESD-preventive wrist strap that was included in the accessory kit.
Step 3
Switch the power supply circuit-breaker switch to the Off (O) position.
Step 4
Pull the terminal block plug connector out of the terminal block head in the power supply.
Step 5
Loosen the captive screws on the DC power supply.
Step 6
Grasping the power supply handle with one hand, pull the power supply out from the chassis while
supporting it with the other hand.
Step 7
Replace the DC power supply. If the power supply bay is to remain empty, must install a blank filler plate
(Cisco part number A900-PWR-BLANK) over the opening, and secure it with the captive installation
screws.
Installing the AC power Supply

The following sections describe how to install a AC power supply in the Cisco ASR 903 Router:
Warning
Installing the AC Power Supply Module, page 3-33
Activating the AC Power Supply, page 3-34
This product requires short-circuit (over current) protection, to be provided as part of the building
installation. Install only in accordance with national and local wiring regulations.
Installing the AC Power Supply Module

Follow these steps to install the power supply module:
Step 1
Ensure that the system (earth) ground connection has been made. For ground connection installation
instructions, see the Installing the Chassis Ground Connection section on page 3-8.
Step 2
If necessary, remove the blank power supply filler plate from the chassis power supply bay opening by
loosening the captive installation screws.
Step 3
Grasp the power supply handle with one hand. Place your other hand underneath the power supply, as
shown in Figure 3-27. Slide the power supply into the power supply bay. Make sure that the power
supply is fully seated in the bay.

OL-25178-08
3-33
Chapter 3
Figure 3-27
GE-0
GE-1
Installing the AC Power Supply
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
FAN TEMP
PWR
STAT
CRIT MAJ MIN

GE-0
GE-1
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
GE-0
GE-1
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
PWR
STAT
PWR
RUDY RSP
STAT
SYNC
ACT
PWR
MEM
CONSOLE
1PPS
IN
1PPS
OUT
1OMHZ
IN
1OMHZ
OUT
PWR
TOD
BITS
STAT
L
7 S
7 S
7 S
MGMT
ENET
STAT
PWR
ALARM
PWR
STAT
Step 4
Warning
344750
STAT
Tighten the captive installation screws of the power supply. The recommended maximum torque is 5.5
in.-lb (.62 N-m).
Power supply captive installation screws must be tight to ensure protective grounding continuity.
Activating the AC Power Supply

Follow these steps to activate the AC power supply:
Step 1
Plug the power cord into the power supply.
Step 2
Connect the other end of the power cord to an AC-input power source.
Step 3
Verify power supply operation by checking that the power supply LEDs are in the following states:
INPUT OK LED is green
OUTPUT FAIL LED is green
Step 4
If the LEDs indicate a power problem, see the Chapter 4, Troubleshootingfor troubleshooting
information.
Step 5
If you are installing a redundant power supply, repeat these steps for the second power source.
Note
If you are installing a redundant AC power supply, ensure that each power supply is connected to a
separate power source in order to prevent power loss in the event of a power failure.
Removing and Replacing the AC Power Supply

This section describes how to remove and replace the AC power supply.
Note
The Cisco ASR 903 Router power supplies are hot-swappable. If you have installed redundant power
supply modules, you can replace a single power supply without interrupting power to the router.
3-34
OL-25178-08
Chapter 3

Caution
To avoid erroneous failure messages, allow at least 2 minutes for the system to reinitialize after a power
supply has been removed or replaced.
Warning
When you install the unit, the ground connection must always be made first and disconnected last.
Statement 1046
Warning
Statement 1003
Warning
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030
Warning
Follow these steps to remove and replace the AC power supply:

Step 1
Disconnect the power cord from the power source. Do not touch the metal prongs on the power cord
when it is still connected to the power supply.
Step 2
Remove the power cord from the power connection on the power supply. Do not touch the metal prongs
embedded in the power supply.
Step 3
Loosen the captive installation screws.
Step 4
Grasp the AC power supply with one hand, and slide it part of the way out of the chassis. Place your
other hand underneath the power supply, and slide it completely out of the chassis.
Step 5
If the power supply bay is to remain empty, install a blank filler plate (Cisco part number
A900-PWR-BLANK) over the opening, and secure it with the captive installation screws.
Installing Dust Caps

The following list provides the product IDs (PIDs) for the dust caps that are available for each port type:
RJ-45A900-DCAP-RJ45-S= (24 dust caps per package) or A900-DCAP-RJ45-L= (240 caps per
package)
SFPA900-DCAP-SFP-S= (24 caps per package) or A900-DCAP-SFP-L= (240 caps per package)
USBA900-DCAP-USB-S= (12 dust caps per package) or A900-DCAP-USB-L= (120 dust caps
per package)
XFP/QSFPA900-DCAP-XFP-S= (12 dust caps per package) or A900-DCAP-XFP-L= (120 dust

caps per package)

OL-25178-08
3-35
Chapter 3
Connecting the Cisco ASR 903 Router to the Network
Figure 3-28
Dust Cap
358040
Dust cap
To install the dust cap:

1.
Hold the dust cap by its handle.
2.
Insert the dust cap in to the appropriate unused ports (RJ-45, SFP, USB, or XFP/QSFP) on the
chassis front panel.

The following sections describe how to connect cables on the Cisco ASR 903 Router:
Note
Connecting Console Cables, page 3-37
Connecting to the Auxiliary Port, page 3-42
Connecting a Management Ethernet Cable, page 3-44
Installing and Removing SFP and XFP Modules, page 3-44
Connecting a USB Flash Device, page 3-44
Connecting Timing Cables, page 3-45
Connecting Ethernet Cables, page 3-48
Connecting Cables to SFP Modules, page 3-49
Connecting T1/E1 cables, page 3-49
Connecting Serial Cables, page 3-52
Connecting the Fan Tray Alarm Port, page 3-54
Connector and Cable Specifications, page 3-54
When installing the cabling to the RSPs, we recommend that you leave a service loop of extra cabling
3-36
OL-25178-08
Chapter 3

Connecting Console Cables

The following sections describe how to connect to the Cisco ASR 903 Router using console cables:
Note
Connecting to the Serial Port using Microsoft Windows, page 3-37
Connecting to the Console Port using Mac OS X, page 3-39
Connecting to the Console Port using Linux, page 3-39
Installing the Cisco Microsoft Windows USB Device Driver, page 3-40
Uninstalling the Cisco Microsoft Windows USB Driver, page 3-41
You cannot use the USB and RS232 console ports at the same time; if you insert the USB cable into the
router, the RS232 port is disabled.
Connecting to the Serial Port using Microsoft Windows

This procedure shows how to connect to the serial port using Microsoft Windows.
Note
Install the USB device driver before establishing a physical connection between the router and the PC,
by using the USB Console cable plugged into the USB serial port. Otherwise, the connection will fail.
For more information, see the Installing the Cisco Microsoft Windows USB Device Driver section on
page 3-40.
Step 1
Connect the end of the console cable with the RJ45 connector to the light blue console port on the router.
or
Connect a USB Type A-to-Type A cable to the USB console port as shown in Figure 3-29. If you are
using the USB serial port for the first time on a Windows-based PC, install the USB driver now according
to the instructions in the following sections.
Installing the Cisco Microsoft Windows XP USB Driver section on page 3-40
Installing the Cisco Microsoft Windows 2000 USB Driver section on page 3-40
Installing the Cisco Microsoft Windows Vista USB Driver section on page 3-41
Note
You cannot use the USB port and the EIA port concurrently. See Connecting to the Auxiliary
Port section on page 3-42. When the USB port is used it takes priority over the RJ45 EIA port.
Note
The USB Type A-to-Type A cable is not included with the Cisco ASR 903 Router; it is ordered
separately.
Step 2
Connect the end of the cable with the DB-9 connector (or USB Type-A) to the terminal or PC. If your
terminal or PC has a console port that does not accommodate a DB-9 connector, you must provide an
appropriate adapter for that port.
Step 3
To communicate with the router, start a terminal emulator application, such as Microsoft Windows
HyperTerminal. This software should be configured with the following parameters:

OL-25178-08
3-37
Chapter 3
9600 baud
8 data bits
no parity
1 stop-bit
no flow control
Figure 3-29
Connecting the USB Console Cable to the Cisco ASR 903 Router
MEM
GE-0
GE-1
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
GE-0
GE-1
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
PWR
1PPS
IN
CONSOLE
RUDY RSP
FAN TEMP
SYNC
STAT
ACT
PWR
PWR
MEM
CONSOLE
1PPS
IN
1PPS
OUT
1OMHZ
IN
1OMHZ
OUT
TOD
BITS
MGMT
ENET
MEM
CONSOLE
1PPS
IN
1PPS
OUT
1OMHZ
IN
1OMHZ
OUT
TOD
BITS
MGMT
ENET
STAT
24V60V
28A
CRIT MAJ MIN
STAT
STAT
GE-0
GE-1
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
PWR
RUDY RSP
STAT
SYNC
ACT
PWR
STAT
L
7 S
7 S
7 S
PWR
STAT
PWR
STAT
INPUT
OK
OUTPUT
FAIL
24V60V
28A
INPUT
OK
OUTPUT
FAIL
ALARM
282404
PWR
1
2
USB Type-A console port
USB Type-A to USB Type-A Console cable
USB Type-A
3-38
OL-25178-08
Chapter 3

Connecting to the Console Port using Mac OS X

This procedure describes how to connect a Mac OS X system USB port to the console using the built in
OS X Terminal utility.
Step 1
Use the Finder to go to Applications > Utilities > Terminal.
Step 2
Connect the OS X USB port to the router.
Step 3
Enter the following commands to find the OS X USB port number:

macbook:user$ cd /dev
macbook:user$ ls -ltr /dev/*usb*
crw-rw-rw- 1 root
wheel
DT-macbook:dev user$
Step 4
9,
66 Apr
1 16:46 tty.usbmodem1a21
Connect to the USB port with the following command followed by the router USB port speed
macbook:user$ screen /dev/tty.usbmodem1a21 9600
To disconnect the OS X USB console from the Terminal window
Enter Ctrl-a followed by Ctrl-\
Connecting to the Console Port using Linux

This procedure shows how to connect a Linux system USB port to the console using the built in Linux
Terminal utility.
Step 1
Open the Linux Terminal window.
Step 2
Connect the Linux USB port to the router.
Step 3
Enter the following commands to find the Linux USB port number
root@usb-suse# cd /dev
root@usb-suse /dev# ls -ltr *ACM*
crw-r--r-1 root
root
188,
root@usb-suse /dev#
Step 4
0 Jan 14 18:02 ttyACM0
Connect to the USB port with the following command followed by the router USB port speed
root@usb-suse /dev# screen /dev/ttyACM0 9600
To disconnect the Linux USB console from the Terminal window
Enter Ctrl-a followed by : then quit

OL-25178-08
3-39
Chapter 3
Installing the Cisco Microsoft Windows USB Device Driver

A USB device driver must be installed the first time a Microsoft Windows-based PC is connected to the
USB serial port on the router.
This section contains the following topics:
Installing the Cisco Microsoft Windows XP USB Driver
Installing the Cisco Microsoft Windows 2000 USB Driver
Installing the Cisco Microsoft Windows Vista USB Driver
Installing the Cisco Microsoft Windows XP USB Driver

This procedure shows how to install the Microsoft Windows XP USB driver. Download the driver for
your router model from the Tools and Resources Download Software site, USB Console Software
category, at the following URL:
http://tools.cisco.com/support/downloads/go/Redirect.x?mdfid=268437899
Step 1
Unzip the file Cisco_usbconsole_driver_X_X.zip (where X is a revision number).
Step 2
If using 32-bit Windows XP double-click the file setup.exe from the Windows_32 folder, or if using
64-bit Windows XP double-click the file setup(x64).exe from the Windows_64 folder.
Step 3
The Cisco Virtual Com InstallShield Wizard begins. Click Next.
Step 4
The Ready to Install the Program window appears, Click Install.
Step 5
The InstallShield Wizard Completed window appears. Click Finish.
Step 6
Connect the USB cable to the PC and router USB console ports. The EN LED for the USB console port
turns green, and within a few moments the Found New Hardware Wizard appears. Following the
instructions to complete the installation of the driver.
Step 7
The USB console is ready for use.
Installing the Cisco Microsoft Windows 2000 USB Driver

This procedure shows how to install the Microsoft Windows 2000 USB driver.
Step 1
Obtain the file Cisco_usbconsole_driver.zip from the Cisco.com web site and unzip it.
Step 2
Double-click the file setup.exe.
Step 3
Step 4
Step 5
Step 6
turns green, and within a few moments a series of Found New Hardware Wizard windows appear.
Following the instructions to complete the installation of the driver.
Step 7
3-40
OL-25178-08
Chapter 3

Installing the Cisco Microsoft Windows Vista USB Driver

This procedure shows how to install the Microsoft Windows Vista USB driver.
Step 1
Obtain the file Cisco_usbconsole_driver.zip from the Cisco.com web site and unzip it.
Step 2
If using 32-bit Windows Vista double-click the file setup.exe from the Windows_32 folder, or if using
64-bit Windows Vista double-click the file setup(x64).exe from the Windows_64 folder.
Step 3
Step 4
Note
If a User Account Control warning appears, click Allow - I trust this program... to proceed.
Step 5
Step 6
turns green, and within a few moments a pop up window stating Installing device driver software
appears. Following the instructions to complete the installation of the driver.
Step 7
Uninstalling the Cisco Microsoft Windows USB Driver

This section provides instructions for how to uninstall the Cisco Microsoft Windows USB device driver.
Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver
Uninstalling the Cisco Microsoft Windows Vista USB Driver
Uninstalling the Cisco Microsoft Windows XP and 2000 USB Driver

This procedure shows you how to uninstall both the Microsoft Windows XP and 2000 USB driver. The
driver can be removed using the Windows Add Remove Programs utility or the setup.exe program.
Using the Add Remove Programs Utility
Note
Disconnect the router console terminal before uninstalling the driver.
Step 1
Click Start > Control Panel > Add or Remove Programs.
Step 2
Scroll to Cisco Virtual Com and click Remove.
Step 3
When the Program Maintenance window appears, select the Remove radio button. Click Next.
Using the Setup.exe Program
Note

OL-25178-08
3-41
Chapter 3
Step 1
Run the setup.exe for Windows 32-bit or setup(x64).exe for Windows-64bit. Click Next.
Step 2
The InstallShield Wizard for Cisco Virtual Com appears. Click Next.
Step 3
Step 4
When the Remove the Program window appears, click Remove.
Step 5
When the InstallShield Wizard Completed window appears click Finish.
Uninstalling the Cisco Microsoft Windows Vista USB Driver

This procedure shows you how to uninstall the Microsoft Windows Vista USB driver.
Note
Step 1
Run the setup.exe for Windows 32-bit or setup(x64).exe for Windows-64bit. Click Next.
Step 2
The InstallShield Wizard for Cisco Virtual Com appears. Click Next.
Step 3
Step 4
When the Remove the Program window appears, click Remove.
Note
Step 5
If a User Account Control warning appears, click Allow - I trust this program... to proceed.
When the InstallShield Wizard Completed window appears click Finish.
Connecting to the Auxiliary Port

When a modem is connected to the auxiliary port, a remote user can dial in to the router and configure
it. Use a light blue console cable and the DB-9-to-DB-25 connector adapter.
Note
The console cable and DB-9-to-DB-25 connector are not included with the
Cisco ASR 903 Router; they are ordered separately.
3-42
OL-25178-08
Chapter 3

To connect a modem to the router, follow these steps:

Step 1
Connect the RJ45 end of the adapter cable to the black AUX port on the router, as shown in Figure 3-30.
Figure 3-30
Connecting a Modem to the Cisco ASR 903 Router
MEM
GE-0
GE-1
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
GE-0
GE-1
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
PWR
1PPS
IN
CONSOLE
RUDY RSP
FAN TEMP
SYNC
STAT
ACT
PWR
PWR
MEM
CONSOLE
1PPS
IN
1PPS
OUT
1OMHZ
IN
1OMHZ
OUT
TOD
BITS
MGMT
ENET
MEM
CONSOLE
1PPS
IN
1PPS
OUT
1OMHZ
IN
1OMHZ
OUT
TOD
BITS
MGMT
ENET
STAT
24V60V
28A
CRIT MAJ MIN
STAT
STAT
GE-0
GE-1
GE-2
GE-3
GE-4
GE-5
GE-6
GE-7
PWR
RUDY RSP
STAT
SYNC
ACT
PWR
PWR
STAT
L
7 S
7 S
7 S
STAT
PWR
STAT
INPUT
OK
OUTPUT
FAIL
24V60V
28A
ALARM
INPUT
OK
OUTPUT
FAIL
282405
PWR
1
2
3
4
RJ45 AUX port
RJ45 to DB-9
DB-9 to DB-25 adapter
Modem
Step 2
Connect the DB-9 end of the console cable to the DB-9 end of the modem adapter.
Step 3
Connect the DB-25 end of the modem adapter to the modem.
Step 4
Make sure that your modem and the router auxiliary port are configured for the same transmission speed
(up to 115200 bps is supported) and for mode control with data carrier detect (DCD) and data terminal
ready (DTR) operations.

OL-25178-08
3-43
Chapter 3
Connecting a Management Ethernet Cable

When using the Ethernet Management port in the default mode (speed-auto and duplex-auto) the port
operates in auto-MDI/MDI-X mode. The port automatically provides the correct signal connectivity
through the Auto-MDI/MDI-X feature. The port automatically senses a crossover or straight-through
cable and adapts to it.
However, when the Ethernet Management port is configured to a fixed speed (10 or 100 Mbps) through
command-line interface (CLI) commands, the port is forced to MDI mode.
When in a fixed-speed configuration and MDI mode:
Warning
Use a crossover cable to connect to an MDI port
Use a straight-through cable to connect to an MDI-X port
To comply with the Telcordia GR-1089 NEBS standard for electromagnetic compatibility and safety,
connect the Management Ethernet ports only to intra-building or unexposed wiring or cable. The
intrabuilding cable must be shielded and the shield must be grounded at both ends. The intra-building
port(s) of the equipment or subassembly must not be metallically connected to interfaces that connect
to the OSP or its wiring. These interfaces are designed for use as intra-building interfaces only (Type
2 or Type 4 ports as described in GR-1089-CORE) and require isolation from the exposed OSP cabling.
The addition of Primary Protectors is not sufficient protection in order to connect these interfaces
metallically to OSP wiring.
Installing and Removing SFP and XFP Modules

The Cisco ASR 903 Router supports a variety of SFP and XFP modules, including optical and Ethernet
modules. For information on how to install and remove SFP and XFP modules, see the documentation
for the SFP or XFP module at
http://www.cisco.com/en/US/partner/products/hw/modules/ps5455/prod_installation_guides_list.html
For information about inspecting and cleaning fiber-optic connections, see
http://www.cisco.com/en/US/partner/tech/tk482/tk876/technologies_white_paper09186a0080254eba.s
html
Caution
We recommend that you wait 30 seconds between removal and insertion of an SFP on an interface
module. This time is recommended to allow the transceiver software to initialize and synchronize with
the standby RSP. Changing an SFP more quickly could result in transceiver initialization issues that
disable the SFP.
Connecting a USB Flash Device

To connect a USB flash device to the Cisco ASR 903 Router, insert the memory stick in the USB port
labeled MEM. The Flash memory module can be inserted in only one way, and can be inserted or
removed regardless of whether the router is powered up or not.
Figure 3-31 shows the USB port connector on the Cisco ASR 903 Router.
3-44
OL-25178-08
Chapter 3

Figure 3-31
Cisco ASR 903 Router Flash Token Memory Stick
CONSOL
E
209390
MEM
Removing a USB Flash Device

To remove and then replace a USB flash token memory stick from a Cisco ASR 903 Router, follow these
steps:
Step 1
Pull the memory stick from the USB port.
Step 2
To replace a Cisco USB Flash memory stick, simply insert the module into the USB port labeled MEM
as shown in Figure 3-31 . The Flash memory module can be inserted in only one way, and can be inserted
or removed regardless of whether the router is powered up or not.
Note
You can insert or remove the memory stick whether the router is powered on or not.
This completes the USB Flash memory installation procedure.
Connecting Timing Cables

The following sections describe how to connect timing cables to the Cisco ASR 903 Router:
Note
Connecting Cables to the BITS Interface, page 3-45
Connecting Cables to a GNSS Interface, page 3-46
Connecting Cables to the BITS Interface

The following steps describe how to connect a cable to the router BITS port:
Step 1
Confirm that the router is powered off.
Step 2
Connect one end of the cable to the BITS port using a straight-through, shielded RJ48C-to-RJ48C cable.

OL-25178-08
3-45
Chapter 3
Step 3
Connect the other end to the BTS patch or demarcation panel at your site.
Step 4
Turn on power to the router.

For information about the BITS port pinouts, see Chapter 4, Troubleshooting.
Note
Warning
Use of two BITS sources or a Y-cable is optional. Each BITS input port is routed to both RSPs,
so that SETS device on each RSP has visibility to both BITS inputs.
connect the BITS ports only to intra-building or unexposed wiring or cable. The intrabuilding cable
must be shielded and the shield must be grounded at both ends. The intra-building port(s) of the
equipment or subassembly must not be metallically connected to interfaces that connect to the OSP
or its wiring. These interfaces are designed for use as intra-building interfaces only (Type 2 or Type 4
ports as described in GR-1089-CORE) and require isolation from the exposed OSP cabling. The
addition of Primary Protectors is not sufficient protection in order to connect these interfaces
Connecting Cables to a GNSS Interface

The following sections describe how to connect cables from the Cisco ASR 903 Router to a GPS unit for
input or output timing of frequency:
Connecting Cables to the Input 10Mhz or 1PPS Interface, page 3-46
Connecting Cables to the Output 10Mhz or 1PPS Interface, page 3-46
Connecting Cables to the ToD Interface, page 3-47
Note
A Y-cable is required to connect to a primary and backup RSP in order to ensure that the router continues
to transmit timing signals in the event of a network failure. For a mini-coax connection, this Y-cable can
be part number CAB-BNC-7INY (7 inch BNC Y-cable). For an Ethernet connection, this Y-cable can be
a RJ45 Cat5 1-to-2 splitter (3 female port RJ45 connector).
Note
Connecting Cables to the Input 10Mhz or 1PPS Interface

Step 1
Connect one end of a mini-coax Y-cable to the GPS unit.
Step 2
Connect one end of the split-side Y-cable mini-coax to the 10Mhz or 1PPS port on the primary RSP of
the Cisco ASR 903 Router.
Step 3
Connect the other end of the split-side Y-cable mini-coax to the 10Mhz or 1PPS port on the backup RSP
of the Cisco ASR 903 Router.
Connecting Cables to the Output 10Mhz or 1PPS Interface

Step 1
Connect one end of a mini-coax Y-cable to the Slave unit.
3-46
OL-25178-08
Chapter 3

Step 2
Connect one end of the split-side Y-cable mini-coax to the 10Mhz or 1PPS port on the primary RSP of
the Cisco ASR 903 Router.
Step 3
Connect the other end of the split-side Y-cable mini-coax to the 10Mhz or 1PPS port on the backup RSP
of the Cisco ASR 903 Router.
Connecting Cables to the ToD Interface

Step 1
Connect one end of a straight-through Ethernet cable to the GPS unit.
Step 2
Connect one end of the split-side Y-cable Ethernet to the ToD port on the primary RSP of the
Step 3
Connect the other end of the split-side Y-cable Ethernet to the ToD port on the backup RSP of the
Note
Warning
Note
For instructions on how to configure clocking, see the Cisco ASR 903 Router Software Configuration
Guide.
connect the ToD ports only to intra-building or unexposed wiring or cable. The intrabuilding cable
For more information about GPS port pinouts, see Chapter 4, Troubleshooting.
Connecting a Cable to the GNSS Antenna Interface

Note
The GNSS module is not hot swappable.
Step 1
Connect one end of a shielded coaxial cable to the GNSS RF IN port.
Step 2
Connect the other end of the shielded coaxial cable to the GNSS antenna after the primary protector.
Note
The GNSS RF In port should have a primary protector installed to meet the Local Safety guidelines.
The GNSS RF In coaxial cable shield must be connected to the Facility Equipment Ground through
the chassis. The chassis must have the ground wire connected to the Facility Equipment Ground.

OL-25178-08
3-47
Chapter 3
Figure 3-32
Installing the GNSS Module in the RSP
365645
Screw on the GNSS Module
Inserting the GNSS Module
Connecting Ethernet Cables

The Cisco ASR 903 Router interface modules support RJ45 or SFP Ethernet ports. For instructions on
how to connect cables to Ethernet SFP ports, see Connecting Cables to SFP Modules, page 3-49.
The RJ45 port supports standard straight-through and crossover Category 5 unshielded twisted-pair
(UTP) cables. Cisco Systems does not supply Category 5 UTP cables; these cables are available
commercially.
Warning
Note
connect the Gigabit Ethernet ports only to intra-building or unexposed wiring or cable. The
intrabuilding cable must be shielded and the shield must be grounded at both ends. The intra-building
port(s) of the equipment or subassembly must not be metallically connected to interfaces that connect
to the OSP or its wiring. These interfaces are designed for use as intra-building interfaces only (Type
2 or Type 4 ports as described in GR-1089-CORE) and require isolation from the exposed OSP cabling.
The addition of Primary Protectors is not sufficient protection in order to connect these interfaces
Follow these steps to connect the cable to a copper Gigabit Ethernet port:
Step 1
Confirm that the router is powered off.
Step 2
Connect one end of the cable to the Gigabit Ethernet port on the router.
Step 3
Connect the other end to the BTS patch or demarcation panel at your site.
3-48
OL-25178-08
Chapter 3

Connecting Cables to SFP Modules

For information on connecting cables to Cisco optical and Ethernet SFP interfaces, see
http://www.cisco.com/en/US/partner/products/hw/modules/ps5455/prod_installation_guides_list.html.
Connecting T1/E1 cables

The physical layer interface for the Cisco ASR 903 Router T1/E1 port is a customer-installed
high-density connector. The high-density connector has thumbscrews which should be screwed into the
interface when the cable is installed.
Note
Patch panels are required in order to connect the high-density interface connectors to individual T1/E1
lines.
Installing the Cable Connectors

16 x T1/E1 Cable Connectors
The 16 x T1/E1 interface module requires a patch cable (see Recommended Patch Panel, page 3-52). One
end of the cable (see Figure 3-33) has a 100-pin connector that plugs into the T1/E1 interface module.
Use the thumbscrews on either side of the connector to secure the cable to the interface.
The other end of the cable has two 50-pin Telco connectors that attach to the rear of a 24-port RJ45 patch
panel. Both connectors are identical: one is for Transmit (TX) and the other is for Receive (RX).
Figure 3-33
16 x T1/E1 Cable Connector
Pin 50
Pin
50
Pin
100
Pin
1
Pin
51
RX
Pin
1
Pin 50
Pin
1
282349
TX

OL-25178-08
3-49
Chapter 3
Figure 3-34 shows how the cable is connected between the 16 x T1/E1 interface module and the patch
panel.
Figure 3-34
Cable Installation between 16 x T1/E1 Interface and Patch Panel
1
PORTS
1-16
TRANS
MIT
RECEIV
255735
Patch panel interfaces
For information about the pinout of the cable connecting the T1/E1 interface to the rear of the patch
panel, see the T1/E1 Port Pinout section on page 4-4.

The 32 x T1/E1 interface module requires two patch cables (see Recommended Patch Panel, page 3-52).
Each patch cable (see Figure 3-34) has a 68-pin connectors that connects with each connector port on
the front panel of the 32 x T1/E1 interface module.
Use the thumbscrews on either side of the connectors to secure the cable to the interface.
Figure 3-35

Pin
1
Pin
50
Pin
68
Pin
34
Pin
35
Pin
1
RX
Pin
1
Pin
50
391968
TX
3-50
OL-25178-08
Chapter 3

The other end of the cable has two 50-pin Telco connectors that attach to the rear of a 24-port RJ45 patch
panel. Both connectors are identical: one is for Transmit (TX) and the other is for Receive (RX).
Figure 3-34 shows how the cable is connected between the 32 x T1/E1 interface module and the patch
panel.
Figure 3-36
Cable Installation between 32 x T1/E1 Interface and Patch Panel
POR
TS 0-
15
POR
TS 16
-31
1
TRANSM
IT
RECEIVE
1
TRANSM
IT
391969
RECEIVE
Patch panel interfaces
T1/E1 Pinouts
For information about the pinout of the cable connecting the T1/E1 interface to the rear of the patch
panel, see the T1/E1 Port Pinout section on page 4-4.
RJ45 Cable Pinouts

T1 lines from individual subscribers are attached to RJ45 connectors on the front of the 24-port patch
panel. Each RJ45 port accommodates an individual T1 subscriber line.
For the T1/E1 ports, see the T1/E1 Port Pinout section on page 4-4.
Connecting Cables to the Patch Panel

If you are connecting two T1/E1 interfaces to each other, you must cable both interfaces patch panels
together using a T1 cross-over cable or a T1 straight-through cable. Use shielded cables. The type of
cable you use (cross-over or straight-through) depends on how the T1/E1 interfaces are cabled to their
patch panels:
If both T1/E1 interfaces are connected to their patch panels in the same manner (TX to Transmit and
RX to Receive, or TX to Receive and RX to Transmit), use a T1 cross-over cable to connect the patch
panels.
If both T1/E1 interfaces are connected to their patch panels in a different configuration (TX to
Transmit and RX to Receive on one interface, and TX to Receive and RX to Transmit on the other
interface), use a T1 straight-through cable (standard RJ45 patch cable) to connect the patch panels.

OL-25178-08
3-51
Chapter 3
Warning
connect the T1/E1 ports only to intra-building or unexposed wiring or cable. The intrabuilding cable
Recommended Patch Panel

We recommend using the following T1/E1 patch panels:
The following patch panels are introduced:
CABLE-16T1E1Cable for 16-Port T1/E1 Interface Module, 12 feet
CABLE-32T1E1Cable for 32-Port T1/E1 Interface Module
PANEL-16-BNCBreakout panel with 16 T1/E1 75-ohm BNC ports
PANEL-32-RJ4Breakout panel with 32 T1/E1 100/120- ohm RJ48 ports8
Also, the following patch panels are available from Optical Cable Corporation
(http://www.occfiber.com).
48-port T1 RJ45 patch panel (part number DCC4884/25T1-S)
16-port E1 BNC patch panel (part number DCC16BNC/25T1-S)

To order a patch panel, contact the Sales and Marketing Support staff at Optical Cable Corporation:
800-622-7711 (toll-free in the U.S.A.)
540-265-0690 (outside the U.S.A.)
Connecting Serial Cables

Figure 3-37 shows the supported serial connectors, and Table 3-3 and Table 3-4 detail the supported
cables with the Cisco ASR 903 Router.
Caution
The Cisco ASR 903 Router currently only supports the EIA/TIA-232 connector.
3-52
OL-25178-08
Chapter 3

Figure 3-37
Supported Serial Connectors
H2485
Router connections
EIA/TIA-449
EIA/TIA-232
V.35
X.21
EIA-530
Network connections at the modem or CSU/DSU
Note
The Cisco ASR 903 Router currently supports only the EIA/TIA-232 connector.
Table 3-3
Interface Cables for 12-in-1 Connector
Cable Type
Product Number
Length
Male/Female
Connector
V.35 DTE
CAB-SS-V35MT
10 ft.
Male
M34
V.35 DCE
CAB-SS-V35FC
10 ft.
Female
M34
EIA/TIA-232 DTE
CAB-SS-232MT
10 ft.
Male
DB-25
EIA/TIA-232 DCE
CAB-SS-232FC
10 ft.
Female
DB-25
EIA/TIA-449 DTE
CAB-SS-449MT
10 ft.
Male
DB-37
EIA/TIA-449 DCE
CAB-SS-449FC
10 ft.
Female
DB-37
X.21 DTE
CAB-SS-X21MT
10 ft.
Male
DB-15
X.21 DCE
CAB-SS-X21FC
10 ft.
Female
DB-15
EIA/TIA-530 DTE
CAB-SS-530MT
10 ft.
Male
DB-25
EIA/TIA-530 DTE
CAB-SS-530FC
10 ft.
Female
DB-25

OL-25178-08
3-53
Chapter 3
Table 3-4
Interface Cables for 68-Pin Connector
Cable Type
Product Number
Length
Male/Female
Connector
4-port EIA-232 DTE
CAB-HD4-232MT
10 ft.
Male
DB-25
4-port EIA-232 DCE
CAB-HD4-232FC
10 ft.
Female
DB-25
4-port EIA-232 DTE
CAB-QUAD-ASYNC-F
10 ft.
Female
RJ-45
4-port EIA-232 DTE
CAB-QUAD-ASYNC-M 10 ft.
Male
RJ-45
4-port EIA-232 DTE
CAB-9AS-M
Male
DB-9
10 ft.
For more information on cable specifications and pinouts, see Chapter 4, Troubleshooting.
Connecting the Fan Tray Alarm Port

The fan tray includes an alarm port that maps to 4 dry contact alarm inputs.
The pins on the alarm port are passive signals and can be configured as Normally Open (an alarm
generated when current is interrupted) or Normally Closed (an alarm is generated when a circuit is
established) alarms. You can configure each alarm input as critical, major, or minor. An alarm triggers
alarm LEDs and alarm messages. The relay contacts can be controlled through any appropriate
third-party relay controller. The open/close configuration is an option controlled in IOS.
Warning
connect the alarm ports only to intra-building or unexposed wiring or cable. The intrabuilding cable
Only Pins 1, 2, 4, 5, and 8 are available for customer use. The remaining pins are for Cisco manufacturing
test, and should not be connected. Use a shielded cable for connection to this port for EMC protection.
Table 4-6 summarizes the pinouts on the alarm port in Chapter 4, Troubleshooting.
Step 1
Attach an RJ45 cable to the alarm port.
Step 2
Attach the other end of the RJ45 cable to the relay controller.
For information about how to map alarm inputs to critical, major, and minor alarm conditions, see the
Cisco ASR 903 Router Software Configuration Guide.
Connector and Cable Specifications

For more information on cable specifications and pinouts, see Chapter 4, Troubleshooting.
3-54
OL-25178-08
CH A P T E R
Troubleshooting
The following sections provide information for troubleshooting problems on the Cisco ASR 903 Router.
Pinouts, page 4-1
LED Summary, page 4-13
Pinouts
The following sections describe the pinouts for the Cisco ASR 903 Router interfaces:
BITS Port Pinout, page 4-1
GPS Port Pinout, page 4-2
Time of Day Port Pinout, page 4-3
Alarm Port Pinout, page 4-4
Console/Aux RJ45 RS232 Serial Port Pinout, page 4-4
T1/E1 Port Pinout, page 4-4
Serial Cable Pinouts, page 4-9
Management Ethernet Port Pinout, page 4-11
USB Console Port Pinout, page 4-12
Fiber-Optic Specifications, page 4-13
BITS Port Pinout

Table 4-1 summarizes the BITS port pinout of the Front Panel Building Integrated Timing Supply
RJ48 port.
Table 4-1
BITS Port Pinout
Pin
Signal Name
Direction
Description
RX Ring
Input
Receive Ring
RX Tip
Input
Receive Tip
3
4
Not used
TX Ring
Output
TX Ring

OL-25178-08
4-1
Chapter 4
Troubleshooting
Pinouts
Table 4-1
BITS Port Pinout (continued)
Pin
Signal Name
Direction
Description
TX Tip
Output
TX Tip
Not used
Not used
Not used
GPS Port Pinout

The platform is capable of receiving or sourcing GPS signals of 1 PPS & 10 MHz. These interfaces are
provided by two mini-coax 50-Ohm, 1.0/2.3 DIN series connector on the front panel. Similarly there
are two mini-coax 50-Ohm connectors provided in the front panel to output this 1PPS and 10MHz.
Table 4-2 summarizes the GPS port pinouts.
Table 4-2
GPS Port Pinout
10 Mhz (input and output)
1PPS (input and output)
InputSine wave
InputRectangular pulse
OutputSquare wave
OutputRectangular pulse
Input > 1.7 volt p-p

(+8 to +10 dBm)
Input > 2.4 volts TTL

compatible
Output > 2.4 volts TTL

compatible

compatible
Impedance
50 ohms
50 ohms
Pulse Width
50% duty cycle
26 microseconds
Rise Time
InputAC coupled
40 nanoseconds
Waveform
Amplitude
Output5 nanoseconds
Table 4-3
GPS Port Pinout for ASR 900 RSP3
10 Mhz (input and output)
1PPS (input and output)
InputSine wave
InputRectangular pulse
OutputSine and Square wave
OutputRectangular pulse
Input > 1.7 volt p-p

(+8 to +10 dBm)
Input > 2.4 volts TTL

compatible

compatible

compatible
Impedance
50 ohms
50 ohms
Pulse Width
50% duty cycle
26 microseconds
Rise Time
InputAC coupled
40 nanoseconds
Waveform
Amplitude
Output5 nanoseconds
4-2
OL-25178-08
Chapter 4
Troubleshooting
Pinouts
Time of Day Port Pinout

Table 4-4 summarizes the ToD port pinout for ASR900-RSP1-55.
Table 4-4
RJ45 ToD Port Pinout
Pin
Signal Name
Direction
Description
1PPS_P
Output or Input
1PPS RS422
signal
1PPS_N
Output or Input
1PPS RS422
signal
RESERVED
Output
Do NOT connect
GND
GND
RESERVED
Input
Do NOT connect
TOD_P
Output or Input
Time of Day
character
TOD_N
Output or Input
Time of Day
character
Time of Day
character
Table 4-5 summarizes the TOD pinout for A900-RSP2A and A900-RSP3-3C-400 modules.
Note
This port requires the use of SHIELDED cable for GR-1089-core Intra-Bldg lightning surge
protection. RS422 interface is per industry standard EIA-422 /RS422 specification.
Table 4-5
RJ48 IPPS/ToD Port Pinout
Pin
Signal Name
Direction
Description
RESERVED
Output or Input
V.11 Cable Corporation
RESERVED
Output or Input
1PPS_N
Output
1PPS RS422 signal
GND
5
6
1PPS_P
Input
1PPS RS422 signal
TOD_N
Output or Input
Time of Day R422 output or input signal
TOD_P
Output or Input
Time of Day R422 output or input signal

OL-25178-08
4-3
Chapter 4
Troubleshooting
Pinouts
Alarm Port Pinout

Table 4-6 summarizes the external alarm input pinout.
Table 4-6
External Alarm Input Pinout
Pin
Signal Name
Description
ALARM0_IN
Alarm input 0
ALARM1_IN
Alarm input 1
No connect
ALARM2_IN
Alarm input 2
ALARM3_IN
Alarm input 3
No connect
No connect
COMMON
Alarm common
Console/Aux RJ45 RS232 Serial Port Pinout

Table 4-7 summarizes the console/aux RJ45 RS232 serial port pinout.
Table 4-7
Console/Aux RJ45 RS232 serial port
Pin
Signal Name
Direction
Description
RTS
Output
Request to send
DTR
Output
Data Terminal Ready (always On).
TXD
Output
Transmit data
RI
GND
RXD
Input
Receive data
DSR/DCD
Input
Data set ready/Data Carrier detect
CTS
Input
Clear to send
Ring Indicator
T1/E1 Port Pinout
16 T1/E1 Interface Module Pinout, page 4-4
32 T1/E1 Interface Module Pinout, page 4-6
16 T1/E1 Interface Module Pinout

Table 4-8 summarizes the pinouts of the cable (Tyco part number 2163442-1, Cisco part number
72-5184-01) used to connect the T1/E1 interface module to the rear of the patch panel.
4-4
OL-25178-08
Chapter 4
Troubleshooting
Pinouts
Table 4-8
16 T1/E1 Interface Pinouts
Line
Board
PIns
Signal Name
Telco
TX
Jack
Pin
Board
Pins
Signal Name
Telco
RX
Jack
Pin
Line 0
88
TX_RING_P1
39
92
RX_RING_P1
39
38
TX_TIP_P1
14
42
RX_TIP_P1
14
87
TX_RING_P2
38
91
RX_RING_P2
38
37
TX_TIP_P2
13
41
RX_TIP_P2
13
76
TX_RING_P3
35
80
RX_RING_P3
35
26
TX_TIP_P3
10
30
RX_TIP_P3
10
75
TX_RING_P4
34
79
RX_RING_P4
34
25
TX_TIP_P4
29
RX_TIP_P4
100
TX_RING_P5
41
94
RX_RING_P5
41
50
TX_TIP_P5
16
44
RX_TIP_P5
16
99
TX_RING_P6
40
93
RX_RING_P6
40
49
TX_TIP_P6
15
43
RX_TIP_P6
15
86
TX_RING_P7
37
82
RX_RING_P7
37
36
TX_TIP_P7
12
32
RX_TIP_P7
12
85
TX_RING_P8
36
81
RX_RING_P8
36
35
TX_TIP_P8
11
31
RX_TIP_P8
11
64
TX_RING_P9
31
68
RX_RING_P9
31
14
TX_TIP_P9
18
RX_TIP_P9
63
TX_RING_P10
30
67
RX_RING_P10
30
13
TX_TIP_P10
17
RX_TIP_P10
52
TX_RING_P11
27
56
RX_RING_P11
27
TX_TIP_P11
RX_TIP_P11
51
TX_RING_P12
26
55
RX_RING_P12
26
TX_TIP_P12
RX_TIP_P12
74
TX_RING_P13
33
70
RX_RING_P13
33
24
TX_TIP_P13
20
RX_TIP_P13
73
TX_RING_P14
32
69
RX_RING_P14
32
23
TX_TIP_P14
19
RX_TIP_P14
62
TX_RING_P15
29
58
RX_RING_P15
29
12
TX_TIP_P15
RX_TIP_P15
61
TX_RING_P16
28
57
RX_RING_P16
28
11
TX_TIP_P16
RX_TIP_P16
Line 1
Line 2
Line 3
Line 4
Line 5
Line 6
Line 7
Line 8
Line 9
Line 10
Line 11
Line 12
Line 13
Line 14
Line 15

OL-25178-08
4-5
Chapter 4
Troubleshooting
Pinouts
Figure 4-1 shows the wiring schematic of the cable used to connect the T1/E1 interface module to the
rear of the patch panel.
Wiring Schematic of Cable between 16 T1/E1 Interface and Patch Panel
343344
Figure 4-1
32 T1/E1 Interface Module Pinout

Table 4-9 summarizes the pinouts of the cable used to connect the 32 T1/E1 interface module to the rear
of the patch panel.
4-6
OL-25178-08
Chapter 4
Troubleshooting
Pinouts
Table 4-9
32 T1/E1 Pinout
Board
Connec
tor
Line
Board
PIns
Signal Name
Telco
TX
Jack
Pin
Board
Pins
Signal Name
Telco Jack
RX
Pin
TX_RING_P0
39
66
RX_RING_P0
39
TX_TIP_P0
14
32
RX_TIP_P0
14
TX_RING_P1
38
65
RX_RING_P1
38
TX_TIP_P1
13
31
RX_TIP_P1
13
TX_RING_P2
35
62
RX_RING_P2
35
TX_TIP_P2
10
28
RX_TIP_P2
10
TX_RING_P3
34
61
RX_RING_P3
34
TX_TIP_P3
27
RX_TIP_P3
TX_RING_P4
41
68
RX_RING_P4
41
TX_TIP_P4
16
34
RX_TIP_P4
16
TX_RING_P5
40
67
RX_RING_P5
40
TX_TIP_P5
15
33
RX_TIP_P5
15
TX_RING_P6
37
64
RX_RING_P6
37
TX_TIP_P6
12
30
RX_TIP_P6
12
TX_RING_P7
36
63
RX_RING_P7
36
TX_TIP_P7
11
29
RX_TIP_P7
11
TX_RING_P8
31
58
RX_RING_P8
31
TX_TIP_P8
24
RX_TIP_P8
TX_RING_P9
30
57
RX_RING_P9
30
TX_TIP_P9
23
RX_TIP_P9
Line
10
36
TX_RING_P10
27
54
RX_RING_P10
27
TX_TIP_P10
20
RX_TIP_P10
Line
11
35
TX_RING_P11
26
53
RX_RING_P11
26
TX_TIP_P11
19
RX_TIP_P11
Line
12
42
TX_RING_P12
33
60
RX_RING_P12
33
TX_TIP_P12
26
RX_TIP_P12
Line
13
41
TX_RING_P13
32
59
RX_RING_P13
32
TX_TIP_P13
25
RX_TIP_P13
Line
14
38
TX_RING_P14
29
56
RX_RING_P14
29
TX_TIP_P14
22
RX_TIP_P14
Line
15
37
TX_RING_P15
28
55
RX_RING_P15
28
TX_TIP_P15
21
RX_TIP_P15
Line 0 48
14
Line 1 47
13
Line 2 44
10
Line 3 43
9
Line 4 50
16
Line 5 49
15
Line 6 46
12
Line 7 45
11
Line 8 40
6
PORTS 0-15
Line 9 39

OL-25178-08
4-7
Chapter 4
Troubleshooting
Pinouts
Table 4-9
32 T1/E1 Pinout
PORTS 16-31
Board
Connec
tor
Line
Board
PIns
Signal Name
Telco
TX
Jack
Pin
Board
Pins
Signal Name
Telco Jack
RX
Pin
Line
16
48
TX_RING_P16
39
66
RX_RING_P16
39
14
TX_TIP_P16
14
32
RX_TIP_P16
14
Line
17
47
TX_RING_P17
38
65
RX_RING_P17
38
13
TX_TIP_P17
13
31
RX_TIP_P17
13
Line
18
44
TX_RING_P18
35
62
RX_RING_P18
35
10
TX_TIP_P18
10
28
RX_TIP_P18
10
Line
19
43
TX_RING_P19
34
61
RX_RING_P19
34
TX_TIP_P19
27
RX_TIP_P19
Line
20
50
TX_RING_P20
41
68
RX_RING_P20
41
16
TX_TIP_P20
16
34
RX_TIP_P20
16
Line
21
49
TX_RING_P21
40
67
RX_RING_P21
40
15
TX_TIP_P21
15
33
RX_TIP_P21
15
Line
22
46
TX_RING_P22
37
64
RX_RING_P22
37
12
TX_TIP_P22
12
30
RX_TIP_P22
12
Line
23
45
TX_RING_P23
36
63
RX_RING_P23
36
11
TX_TIP_P23
11
29
RX_TIP_P23
11
Line
24
40
TX_RING_P24
31
58
RX_RING_P24
31
TX_TIP_P24
24
RX_TIP_P24
Line
25
39
TX_RING_P25
30
57
RX_RING_P25
30
TX_TIP_P25
23
RX_TIP_P25
Line
26
36
TX_RING_P26
27
54
RX_RING_P26
27
TX_TIP_P26
20
RX_TIP_P26
Line
27
35
TX_RING_P27
26
53
RX_RING_P27
26
TX_TIP_P27
19
RX_TIP_P27
Line
28
42
TX_RING_P28
33
60
RX_RING_P28
33
TX_TIP_P28
26
RX_TIP_P28
Line
29
41
TX_RING_P29
32
59
RX_RING_P29
32
TX_TIP_P29
25
RX_TIP_P29
Line
30
38
TX_RING_P30
29
56
RX_RING_P30
29
TX_TIP_P30
22
RX_TIP_P30
Line
31
37
TX_RING_P31
28
55
RX_RING_P31
28
TX_TIP_P31
21
RX_TIP_P31
Figure 4-1 shows the wiring schematic of the cable used to connect the 32 T1/E1 interface module to the
rear of the patch panel.
4-8
OL-25178-08
Chapter 4
Troubleshooting
Pinouts
Figure 4-2
32 T1/E1 Wiring Schematic of Cable between 32 T1/E1 Interface and Patch Panel
CONN P2
50 POSN
50 POSN
364231
SHELL
SHELL
CONN P3
CONN P1
8 T1/E1 Interface Module RJ48C Port Pinnouts

Table 4-10
RJ48C Connector Pin-out for 8 T/E1 Interface Module
Pin
Signal
Direction
Description
RX_TIP
Input
Receive Tip
RX_RING
Output
Receive Ring
Not Connected
TX_TIP
Input
Receive Tip
TX_RING
Output
Receive Ring
Not Connected
Not Connected
Not Connected
Serial Cable Pinouts

The following sections summarize the pinouts on the serial interface module when used with the cable
types specified in Connecting Serial Cables, page 3-52.
DB-9 Connector Pinouts

Table 4-11 summarizes the pinouts for each serial interface type when using a DB-9 connector.

OL-25178-08
4-9
Chapter 4
Troubleshooting
Pinouts
Table 4-11
DB-9 Pin-outs
Pin
Standard DB-9
Direction
Description
RS-485
IRIG-B
NC
Output
Unused
NC
NC
RxD
Input
Receive
NC
NC
TxD
Output
Transmit
IRIG-B (RS232)
IRIG-B (RS232)
DTR
Output
DTR
TxD-
IRIG-B- (RS485)
GND
GND
GND
GND
DSR
Input
DSR
RxD
NC
RTS
Output
RTS
TxD+
IRIG-B+
CTS
Input
CTS
RxD+ (
NC
NC/GND
Unused or Ring NC
NC
Note
Twisted pairs are 2-5, 6-8, 4-7.
Note
The X.21, V.35, RS-485, EIA-449, EIA-530, and IRIG-B standards are not currently supported by
software.
RJ-45 Connector Pinouts

Table 4-12 summarizes the pinouts for each serial interface type when using an RJ-45 connector.
Table 4-12
RJ45 Pinout
Pin
Standard DB-9
Direction
Description
RS-485
IRIG-B
RTS
Input
Ready to send
RxD+ (RS485)
NC
DTR
Input
DTR
RxD- (RS485)
NC
TxD
Input
Transmit
NC
NC
GND
Signal ground
Gnd
Gnd
GND
Signal ground
Gnd
Gnd
RxD
Output
Receive data
IRIG-B (RS232)
IRIG-B (RS232)
DST
Output
DSR
TxD-
IRIG-B- (RS485)
CTS
Output
CTS
TxD+
IRIG-B+ (RS485)
Note
Twisted Pairs are: 1-2, 3-6, 4-5, 7-8.
Note
The X.21, V.35, RS-485, EIA-449, EIA-530, and IRIG-B standards are not currently supported by
software.
4-10
OL-25178-08
Chapter 4
Troubleshooting
Pinouts
E and M Interface Module Pinouts

Table 4-13
RJ45 Front End Pinout
Type
1
2
Pin
Signal
Description
SIG_BAT_N48V
48V signaling battery
M_SIG_IN
Signaling input
RING_AUDIO_IN
Ring, audio input
RING_AUDIO_IN_O
UT
Ring, audio
R1
input/ouput or output
TIP_AUDIO_IN_OUT Tip, audio

input/output or
output
T1
TIP_AUDIO_IN
Tip, audio input
E_SIG_OUT
Signaling output
SIG_GND_RETURN
Signaling ground
return
SB
SB
Usage
Not used in 2-wire

mode
4-wire mode: Output
2-wire mode: InOut
Not used in 2-wire

mode
SG
SG
Management Ethernet Port Pinout

A single management copper ENET port supporting 10/100/1000Base-T operation exists on each RSP.
There is no direct access to the CPU of the other RSP. It uses a standard RJ45 jack.
Note
This is not a data plane port.
Table 4-14 summarizes the Management Ethernet port pinout.

Table 4-14
Management Ethernet Port Pinout
Pin
Signal Name
TRP0+
TRP0-
TRP1+
TRP1-
TRP2+
TRP2-
TRP3+
TRP3-
Description

OL-25178-08
4-11
Chapter 4
Troubleshooting
Pinouts
USB Console Port Pinout

Two individual Type-A USB connector are used for USB console and USB mass storage. One single
USB 2.0 Type-A receptacle is provided on the RSP front panel for providing console access to
ROMMON, IOS-XE and diagnostics. It operates as a USB peripheral only for connection to an external
host PC. This requires the use of a Type-A to Type-A connector instead of a standard USB cable.
Note
The use of the USB console is mutually exclusive with the RS232 console/Aux port. While a
USB cable is inserted, access is automatically switched to this port.
The other single USB 2.0 Type-A receptacle is provided on the RSP front panel for inserting external
USB mass storage devices such as standard USB flash drives. It is used to load images, store
configurations, write logs, etc. It supports operation up to 12Mbps
Table 4-15 summarizes the USB console port pinout.
Table 4-15
Single USB Console Port
Pin
Signal Name
A1
Vcc
+5VDC (500mA)
A2
D-
Data -
A3
D+
Data +
A4
Gnd
Ground
Note
Direction
Description
The USB Console port +5VDC is input and operates as an USB peripheral device.
USB Flash/MEM Port Pinout

Table 4-16 summarizes the USB flash/MEM port pinout.
Table 4-16
Single USB Flash/MEM Port
Pin
Signal Name
Direction
Description
A1
Vcc
+5VDC (500mA)
A2
D-
Data -
A3
D+
Data +
A4
Gnd
Ground
Note
USB TYPE-A receptacle used.
Note
The USB flash/MEM port +5VDC is output. We provide power for USB flash/MEM, and it
operates as a USB host device.
4-12
OL-25178-08
Chapter 4
Troubleshooting
LED Summary
Fiber-Optic Specifications
The specification for optical fiber transmission defines two types of fiber: single-mode and multimode.
Within the single-mode category, three transmission types are defined: short reach, intermediate reach,
and long reach. Within the multimode category, only short reach is available. For information about
optical SFP modules, see the documentation for the SFP module at
http://www.cisco.com/en/US/partner/products/hw/modules/ps5455/prod_installation_guides_list.html.
Cabling Guidelines
The guidelines are recommended during the installation of fiber cables:
Avoid the following actions that can stress the cable:
Pulling or stretching beyond the specified pulling load rate
Bending it beyond the specified bend radius
Creating tension in the suspension runs
Do not touch the fiber tips of fiber cables.
Use single mode or multi-mode optical fiber cables as per the optical transceiver requirement.
Use fiber cleaner to clean the fiber tip as well as transceiver before inserting the fiber cable into the
optical transceiver during installation.
To avoid excessive bending of fiber cable and efficient routing of cables, cable guides or cable
brackets are recommended to be used with the chassis.
LED Summary
The following sections describe the meanings of the LEDs on the Cisco ASR 903 Router.
RSP LEDs, page 4-13
Interface Module LEDs, page 4-16
Power Supply LEDs, page 4-20
Fan Tray LEDs, page 4-21
Alarm Conditions, page 4-21
RSP LEDs
Table 4-17 summarizes the RSP LEDs for the supported RSP modules.
Note
A major alarm condition indicates the failure of a single fan in the fan tray; a critical alarm
indicates the failure of multiple fans. In the event that a single fan fails, the
Cisco ASR 903 Router software adjusts the fan speed to prevent excessive heat within the
chassis.

OL-25178-08
4-13
Chapter 4
Troubleshooting
LED Summary
ASR900-RSP LED
Table 4-17
A900-RSP LEDs
LED
Color/State
Description (two LEDs for each port)
Power
(PWR)
Off
Disabled/no power to RSP
Green
Power rails on RSP in range
Status
(STAT)
Off
Disabled/power down
Red
Failure to boot (lit at reset)
Yellow
Rommon booted
Green
IOS booted and running
Off
Not available
Yellow
Standby (indicates standby RSP)
Green
Active (indicates active RSP)
Active
(ACT)
Management Off
port
Green
(MGMT)
Flashing
green
No connection
Sync status
(SYNC)
Off
Not enabled
Yellow
Free run
Flashing
yellow
Holdover
Green
Locked to source
USB flash
(MEM)
Flashing
green
USB activity
BITS
Off
Out of service/not configured
Amber
Fault or loop condition
Green
In frame/working properly
Connected with no activity

Connected with activity
A900-RSP2 and A900-RSP3 LED Information

The PWR and STAT LEDs are available on the front panel. These LEDs provide power on the board
(PWR) and overall router health (STAT) status. During power up state, these LEDs provide booting
status and report errors.
Note
The digital code signing functionality validates the integrity and authenticity of the ROMMON image
before booting it.
4-14
OL-25178-08
Chapter 4
Troubleshooting
LED Summary
Table 4-18
A900-RSP2 and A900-RSP3 LED
PWR LED State STAT LED State Indication
Comment
Light Green
Image validation failed. System

is in hung state.
Red
Flashing Light Off

Green and
Green
alternatively
Green
Power is OK and the

field-programmable gate array
(FPGA) is nfigured successfully,
but FPGA image validation
failed.
System is up with ROMMON.

Both the FPGA image is
validated successfully, but the
FPGA image passed the control to
booted ROMMON (primary or
micro-loader to boot ROMMON.
secondary) is undetermined.
FPGA configured and core

validated successfully.
Amber
The digital code signing

functionality reported upgrade
FPGA image validation error and
is continuing with the FPGA
image.
System is up with ROMMON.

FPGA image is validated
successfully, but the booted
ROMMON (primary or
secondary) is undetermined.
Red
The digital code signing

functionality reported failure in
the ROMMON image validation.
FPGA is up but both primary

and secondary ROMMON
failed. System is in hung state.
Off
IOS is successfully booted
IOS writes into FPGA register

to indicate that it has booted,
FPGA stops flashing PWR LED
and turns Green. Software now
controls the STAT LED.

OL-25178-08
4-15
Chapter 4
Troubleshooting
LED Summary
Interface Module LEDs

Table 4-19 summarizes the interface module LEDs. This LED summary applies to the following
interface modules:
Note
SFP Gigabit Ethernet Interface Module
RJ45 Gigabit Ethernet Interface Module
XFP 10 Gigabit Ethernet XFP Interface Module
8x1 Gigabit Ethernet SFP + 1x10 Gigabit Ethernet SFP+ Interface Module
8x1 Gigabit Ethernet RJ45 + 1x10 Gigabit Ethernet SFP+ Interface Module
2x10 Gigabit Ethernet SFP+ Interface Module
2x40 Gigabit Ethernet QSFP Interface Module
The Status LED is Amber for the 10 Gigabit Ethernet ports when operating in WAN mode for the
following IMS:
8x1 Gigabit Ethernet SFP + 1x10 Gigabit Ethernet SFP+ Interface Module
8x1 Gigabit Ethernet RJ45 + 1x10 Gigabit Ethernet SFP+ Interface Module
2x10 Gigabit Ethernet SFP+ Interface Module
Table 4-19
LED
Color/State
Description
Power
(PWR)
Off
Disabled/no power to IM
Green
Enabled and power rails on IM in range
Status
(STAT)
Off
Disabled/power-down
Red
Failure (on at reset)
Flashing
Red
Booting (if local CPU)
Green
Operational
Off
Inactive or no connection
Amber
Fault/loop condition
Green
Ok with activity or no activity
Off
Inactive port status
Green
Activity or no activity
Link status
(L)
Speed (S)
4-16
OL-25178-08
Chapter 4
Troubleshooting
LED Summary
OC-3 Interface Module LEDs

Table 4-21 summarizes the LEDs for the OC-3 interface module.
Table 4-20
LED
Color/State
Description
Power
(PWR)
Off
Disabled/no power to IM
Green
Enabled and power rails on IM in range
Status
(STAT)
Off
Disabled/power-down
Red
Failure (on at reset)
Amber
Booting (if local CPU)
Green
Operational
Carrier/
Green
Alarm (C/A) Yellow
SFP receiving good remote signal
Active/
Loopback
(A/L)
Green
SFP ready and operating normally
Yellow
SFP port in loopback state
Remote or local alarm activated
T1/E1 Interface Module LEDs

Table 4-21 summarizes the LEDs for the 16 T1/E1 interface module.
Table 4-21
16 T1/E1 Interface Module LEDs
LED
Color/State
Description (two LEDs for eachT1/E1 port)
Active
Green
Active
Blinking green Standby

Port
Off
Operationally down; card is disabled or shut down
Green
All ports up
Blinking green All ports up and one or more ports in a loopback state
PWR
STAT
Amber
One or more configured ports are down
Blinking
amber
One or more configured ports are down and at least one configured port
is in a loopback state
Off
All ports disabled or shut down
Green
All power rails are within supported range
Red
Disabled
Off
No power on the interface module
Red
Failed
Off
Disabled or powered down
Blinking red
Booting
Green
Active

OL-25178-08
4-17
Chapter 4
Troubleshooting
LED Summary
Table 4-22
LED
Color/State
Active
Green
Active
Blinking green Standby

Port
Off
Green
All ports up
Blinking green All ports up and one or more ports in a loopback state
PWR
STAT
Amber
Blinking
amber
Off
Green
All power rails are within supported range
Red
Disabled
Off
No power on the interface module
Red
Failed
Off
Disabled or powered down
Blinking red
Booting
Green
Active
Table 4-23
LED
Color/State
Active
Green
Active
Blinking green
Standby
Off
Solid Green
All ports up
Blinking green
All ports up and one or more ports in a loopback state
Solid Amber
Blinking amber
Off
Green
Operational
Pulsing Green
Booting
Red
Failure; On at reset
Off
Disabled or power down
Green
IM power rails are in range and are enabled
Off
Disabled; No power to IM
Port
STAT
PWR
4-18
OL-25178-08
Chapter 4
Troubleshooting
LED Summary
Serial Interface Module LEDs

Table 4-21 summarizes the LEDs for the serial interface module.
Table 4-24
Cisco ASR 903 Router Serial IM LEDs
LED Label
Color/State
Meaning
Power (PWR)
Green
All power rails are within spec.
Red
Disabled
Off
No Power
Operating Status (STAT) Red
68-Pin Connector LEDs
Failure
Yellow
Booting (if IM has a local CPU)
Green
Operational
Off
No Power
Green
At least one of the 4 ports is in an up

state.
Blinking Green
At least one of the 4 ports is passing

traffic
Solid Yellow
All four ports are successfully

initialized and in a down state
Blinking Yellow
At least one of the port has failed
Off
All the ports are not enabled (at POR)
12-in-1 Connector LEDs Green
Port is passing traffic
Solid Yellow
Port successfully initialized and in a

down state
Blinking Yellow
Port has failed
Off
Not Enabled (at POR)
E & M Interface Module LEDs

Table 4-25 summarizes the LEDs for the E & M interface module.
Table 4-25
Cisco ASR 903 Router E&M IM LEDs
LED Label
Color/State
Description
Power (PWR)
Green
All power rails are within spec.
Red
Disabled
Off
No Power
Operating Status (STAT) Red
Failure
Yellow
Booting (if IM has a local CPU)
Green
Operational
Off
No Power

OL-25178-08
4-19
Chapter 4
Troubleshooting
LED Summary
Table 4-25
Cisco ASR 903 Router E&M IM LEDs
LED Label
Color/State
Description
Port Bi-color LEDs
Green
Call established
Blinking Green
Not used
Solid Yellow
Call not established
Blinking Yellow
Not used
Off
Initialized
Power Supply LEDs

Table 4-26 summarizes the power supply LEDs for both the AC and DC power supplies.
Table 4-26
DC Power Supply LEDs (A900-PWR-550-D)
LED
Color/State
Description
Input OK
Off
No Input Voltage
Amber
Input voltage out of range
Green
Input voltage within acceptable operating range
Off
Disabled/Forced Shut down/No input power
Red
Power supply fault (internal failure such as over temperature)
Green
Operational
Output Fail
Table 4-27
DC Power Supply LEDs (A900-PWR-1200-D)
LED
Color/State
Description
Input OK
Off
No Input Voltage
Amber
Green
Off
Disabled/Forced Shut down/No input power
Red
Power supply fault (internal failure such as over temperature)
Green
Operational
Blinking
Red
Output ORING FET Failed
Output Fail
Table 4-28
AC Power Supply LEDs (A900-PWR-550-A) and (A900-PWR-!200-A)
LED
Color/State
Description
Input Power
(PWR)
Off
No input voltage
Amber
Green
4-20
OL-25178-08
Chapter 4
Troubleshooting
LED Summary
Table 4-28
AC Power Supply LEDs (A900-PWR-550-A) and (A900-PWR-!200-A)
LED
Color/State
Description
Status
(STAT)
Off
Disabled/power-down/no power
Red
Power supply fault (internal failure)
Green
Operational
Fan Tray LEDs

Table 4-29 summarizes the fan tray LEDs.
Table 4-29
Fan Tray LEDs
LED
Color/State
Description
Status
(TEMP)
Off
Disabled/power down
Amber
Over temperature
Green
OK
Green
Fan rotation in range
Amber
Single fan fault
Red
Two or more fan faults
Minor
(MIN)
Off
No minor alarm
Amber
Minor alarm
Major
(MAJ)
Off
No major alarm
Red
Major alarm
Critical
(CRIT)
Off
No critical alarm
Red
Critical alarm (defaults to ON upon RSP reset)
Fan (FAN)
Alarm Conditions
Table 4-30 summarizes the meaning of alarm conditions on the Cisco ASR 903 Router.
Table 4-30 Alarm Condition Summary
Alarm Type
Alarm Description
Critical
RSP OIR
Power supply OIR
Port in down state
Environmental sensor threshold exceeded (voltage, temperature)
IM OIR
IM crash

OL-25178-08
4-21
Chapter 4
Troubleshooting
LED Summary
Table 4-30 Alarm Condition Summary
Alarm Type
Alarm Description
Major
Standby RSP in ROMmon mode

RSP removed
RSP failure
Info
Port administratively shut down
4-22
OL-25178-08
CH A P T E R

This chapter guides you through a basic router configuration, which is sufficient for you to access your
network. Complex configuration procedures are beyond the scope of this publication and can be found
in the modular configuration and modular command reference publications in the Cisco IOS software
configuration documentation set that corresponds to the software release installed on your Cisco
hardware.
To configure the Cisco ASR 903 Router from a console, you need to connect a terminal to the router
console port.
Checking Conditions Prior to System Startup, page 5-1
Powering Up the Cisco ASR 903 Router, page 5-2
Configuring the Cisco ASR 903 Router at Startup, page 5-5
Safely Powering Off the Cisco ASR 903 Router, page 5-8
Checking Conditions Prior to System Startup

Ensure that the following conditions are addressed before starting up the router:
The Route Switch Processor (RSP) is installed.
The optional Gigabit Ethernet Management port cable is installed.
The chassis is securely mounted and grounded.
The power and interface cables are connected.
Your PC with terminal emulation program (hyperTerminal or equivalent) is connected to the console
port and powered up.
Your PC terminal emulation program is configured for 9600 baud, 8 data bits, 1 stop-bit, no parity,
and flow control is set to none.
You have selected passwords for access control.
Captive installation screws are tight on all removable components.
The console terminal is turned on.
You have determined the IP addresses for the Ethernet and serial interfaces.
Empty card slots or card bays are filled with card blanks. This ensures proper air flow through the
chassis and electromagnetic compatibility (EMC).

OL-25178-08
5-1
Chapter 5
Powering Up the Cisco ASR 903 Router

Make certain that all card slots and compartments are closed off. Install blank faceplates on any empty
slots. Always have power supply slots filled. If you leave a power supply slot uncovered, then you risk
exposure to hazardous voltages on the power pins on the midplane.
Warning
operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement
1029
After installing your Cisco ASR 903 Router and connecting cables, start the router and follow these
steps:
Step 1
Activate the DC power supply using the steps described in Activating the DC Power Supply procedure
on page 3-32.
Caution
Note
Step 2
Do not press any keys on the keyboard until the messages stop and the SYS PWR LED is solid
green. Any keys pressed during this time are interpreted as the first command typed when the
messages stop, which might cause the router to power off and start over. It takes a few minutes
for the messages to stop.
This is only an example of what can display. The system boots differently depending upon
the configuration that ships with your system.
Observe the initialization process. When the system boot is complete (the process takes a few seconds),
the Cisco ASR 903 Router RSP begins to initialize.
Example 5-1
Loading the Default System Boot Image
rommon 1 >
rommon 1 > boot
Located rp_super.ppc.nader.5g.evfc.bin
Image size 211681484 inode num 12, bks cnt 51681 blk size 8*512
######################################################################################
#
#############################################
Boot image size = 211681484 (0xc9e00cc) bytes
Using midplane macaddr
Package header rev 0 structure detected
Calculating SHA-1 hash...done
validate_package: SHA-1 hash:
calculated 479a7d62:6c128ba8:3616b8da:93cb3224:5c1aeb34
expected
479a7d62:6c128ba8:3616b8da:93cb3224:5c1aeb34
Image validated
PPC/IOS XE loader version: 0.0.3

loaded at:
00800000 0D1E2004
image at:
00807673 009B8C69
5-2
OL-25178-08
Chapter 5

initrd at:
isord at:
avail ram:
009B9000 01006219
01007000 0D1DF800
00400000 00800000
Kernel load:
Uncompressing image... dst: 00000000 lim: 00400000 start: 00807673 size:
001B15F6...done.
Now booting the IOS XE kernel
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Router# show version

Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version
12.2(33)XNA, RELEASE SOFTWARE
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Thu 01-May-08 00:29 by mcpre
Cisco IOS-XE software, Copyright (c) 1986-2008 by Cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco ASR903 processor with 541737K/6147K bytes of memory.
4 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
1869396K bytes of physical memory.
7798783K bytes of eUSB flash at bootflash:.
--- System Configuration Dialog --Would you like to enter the initial configuration dialog? [yes/no]: no
Press RETURN to get started!
*Feb 19 17:34:27.361: % Error opening nvram:/ifIndex-table No such file or directory

*Feb 19 17:34:28.235: %ASR1000_MGMTVRF-6-CREATE_SUCCESS_INFO: Management vrf Mgmt-intf
created with ID 4085, ipv4 table-id 0xFF5, ipv6 table-id 0x1E000001

OL-25178-08
5-3
Chapter 5
*Feb 19 17:34:29.720: %PARSER-4-BADCFG: Unexpected end of configuration file.

*Feb 19 17:34:29.809: %NETCLK-5-NETCLK_MODE_CHANGE: Network clock source not
available. The network clock has changed to freerun
*Feb 19 17:34:10.138: %CPPHA-7-SYSREADY: F0: cpp_ha: CPP client process FMAN-FP (5 of
5) ready.
*Feb 19 17:34:29.824: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Feb 19 17:34:10.269: %IOSXE-6-PLATFORM: F0: cpp_cp: cpp_mlp_svr_client_bind:
cpp_mlp_svr_ifm_init() successful
*Feb 19 17:34:10.362: %CPPHA-7-START: F0: cpp_ha: CPP 0 preparing image
/usr/cpp/bin/cpp-mcplo-ucode
*Feb 19 17:34:10.473: %CPPHA-7-START: F0: cpp_ha: CPP 0 startup init image
*Feb 19 17:34:14.688: %CPPHA-7-START: F0: cpp_ha: CPP 0 running init image
*Feb 19 17:34:14.919: %CPPHA-7-READY: F0: cpp_ha: CPP 0 loading and initialization
complete
*Feb 19 17:34:14.919: %CPPHA-6-SYSINIT: F0: cpp_ha: CPP HA system configuration
start.
*Feb 19 17:34:15.179: %IOSXE-6-PLATFORM: F0: cpp_cp: Process
CPP_PFILTER_EA_EVENT__API_CALL__REGISTER
*Feb 19 17:34:15.286: %CPPHA-6-SYSINIT: F0: cpp_ha: CPP HA system enabled.
*Feb 19 17:34:15.287: %CPPHA-6-SYSINIT: F0: cpp_ha: CPP HA system initializaton
complete.
*Feb 19 17:34:30.823: %LINEPROTO-5-UPDOWN: Line protocol on Interface
GigabitEthernet0, changed state to down
*Feb 19 17:35:12.865: %LINK-5-CHANGED: Interface GigabitEthernet0/0/0, changed state
to administratively down
GigabitEthernet0/0/0, changed state to down
*Feb 19 17:35:19.167: %ASR1000_OIR-6-REMSPA: SPA removed from subslot 0/0, interfaces
disabled
*Feb 19 17:35:19.171: %ASR1000_OIR-6-INSCARD: Card (fp) inserted in slot F0
*Feb 19 17:35:19.171: %ASR1000_OIR-6-ONLINECARD: Card (fp) online in slot F0
*Feb 19 17:35:19.187: %ASR1000_OIR-6-INSCARD: Card (cc) inserted in slot 0
*Feb 19 17:35:19.187: %ASR1000_OIR-6-ONLINECARD: Card (cc) online in slot 0
*Feb 19 17:35:19.189: %ASR1000_OIR-6-INSSPA: SPA inserted in subslot 0/0
*Feb 19 17:35:19.452: %SYS-5-RESTART: System restarted -Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version
12.2(33)XNA, RELEASE SOFTWARE
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Thu 20-Dec-07 18:10 by mcpre
*Feb 19 17:35:19.455: %SYS-6-BOOTTIME: Time taken to reboot after reload = 78809
seconds
*Feb 19 17:35:19.551: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Feb 19 17:35:21.669: %DYNCMD-7-CMDSET_LOADED: The Dynamic Command set has been loaded
from the Shell Manager
Router>
5-4
OL-25178-08
Chapter 5

Configuring the Cisco ASR 903 Router at Startup
During the boot process, observe the system LEDs. The LEDs on the shared port adapter go on and off
in an irregular sequence. Once the router has booted, the green STATUS LED comes on and stays on.
Verifying the Front Panel LEDs

The front-panel indicator LEDs provide power, activity, and status information useful during bootup. For
more detailed information about the LEDs, see Chapter 4, Troubleshooting.
Verifying the Hardware Configuration

To display and verify the hardware features, enter the following commands:
show versionDisplays the system hardware version; the installed software version; the names and
sources of configuration files; the boot images; and the amount of installed DRAM, NVRAM, and
flash memory.
show diag slotDisplays the IDPROM information for the assemblies in the chassis.
Checking Hardware and Software Compatibility

To check the minimum software requirements of the Cisco IOS software with the hardware installed on
your Cisco ASR 903 Router, Cisco maintains the Software Advisor tool on Cisco.com. The tool
provides the minimum Cisco IOS requirements for individual hardware modules and components.
Note
To access this tool, you must have a Cisco.com login account.
To access the Software Advisor, click Login at Cisco.com, type Software Advisor in the search box,
and click Go. Click the link for the Software Advisor Tool.
Choose a product family or enter a specific product number to search for the minimum supported
software needed for your hardware.

This section explains how to create a basic running configuration for your Cisco ASR 903 Router.
Note
You need to acquire the correct network addresses from your system administrator or consult
your network plan to determine correct addresses before you can complete the router
configuration.
Before continuing the configuration process, check the current state of the router by entering the show
version command. The show version command displays the release of Cisco IOS software that is
available on the router.

OL-25178-08
5-5
Chapter 5
For information on modifying the configuration after you create it, see the Cisco IOS configuration and
command reference guides.
To configure a Cisco ASR 903 Router from the console, you must connect a terminal or terminal server
to the console port on the Cisco ASR 903 Router RSP. To configure the Cisco ASR 903 Router using the
management Ethernet port, you must have the routers IP address available.
Using the Console Interface

To access the command line interface using the console, follow these steps:
Step 1
Your system is booting and if you answer No, at the prompt:

--- System Configuration Dialog --Would you like to enter the initial configuration dialog? [yes/no]: no
Step 2
Then Press Return to enter user EXEC mode. The following prompt appears:
Router>
Step 3
From user EXEC mode, enter the enable command as shown in the following example:
Router> enable
Step 4
At the password prompt, enter your system password. If an enable password has not been set on your
system, this step may be skipped. The following example shows entry of the password called enablepass:
Password: enablepass
Step 5
When your enable password is accepted, the privileged EXEC mode prompt appears: Router#
Step 6
You now have access to the CLI in privileged EXEC mode and you can enter the necessary commands
to complete your desired tasks. To exit the console session, enter the quit command as shown in the
following example:
Router# quit
Configuring Global Parameters

When you first start the setup program, you must configure the global parameters. These parameters are
used for controlling system-wide settings. Perform the following steps to enter the global parameters:
Step 1
Connect a console terminal to the console port, and then boot the router.
Note
This is only an example of the output display; prompts may vary.
When you see this information, you have successfully booted your router:
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
5-6
OL-25178-08
Chapter 5

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
.
.
.
--- System Configuration Dialog --Would you like to enter the initial configuration dialog? [yes/no]: yes
Press RETURN to get started!
Step 2
The first sections of the configuration script appear only at an initial system startup. On subsequent uses
of the setup facility, the script begins with a System Configuration Dialog as shown below: When asked
if you would like to enter the initial configuration dialog, enter yes.
Would you like to enter the initial configuration dialog? [yes/no] yes
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Basic management setup configures only enough connectivity for management of the
system, extended setup will ask you to configure each interface on the system.
Basic management setup configures enough connectivity for managing the system; extended setup will
ask you to configure each interface on the system. For detailed information about setting global
parameters, refer to the Cisco ASR 903 Router Software Configuration Guide.
Checking the Running Configuration Settings

To check the value of the settings you have entered, enter the show running-config command at the
prompt:
Router#
Router# show running-config
To review changes you make to the configuration, use the EXEC mode show startup-config command
to see the changes and copy run-start stored in NVRAM.
Note
The ROMMON variable is set from factory to boot the IOS as

?"BOOT="bootflash:Image/packages.conf"?. However, the boot command is not pre-configured.
As the boot command is not configured, the router boots to ROMMON mode after the first power cycle,
and the following message is displayed:
no valid BOOT image found
Final autoboot attempt from default boot device...
Located tracelogs.030
Image size 6181 inode num 13, bks cnt 2 blk size 8*512
Boot image size = 6181 (0x1825) bytes

OL-25178-08
5-7
Chapter 5
Unknown image structure

boot: cannot determine first file name on device "bootflash:/"
rommon1>.
To avoid the router booting into ROMMON state, it's highly recommended that you set the boot
command prior to the first reload.
Router(config)# boot system flash bootflash:/Image/asr903rsp1-universalk9.x.x.x.-ext.bin
Saving the Running Configuration to NVRAM

To store the configuration or changes to your startup configuration in NVRAM, enter the copy
running-config startup-config command at the Router# prompt:
Router# copy running-config startup-config
Using this command saves the configuration settings that you created in the router using configuration
mode and the setup facility. If you fail to do this, your configuration will be lost the next time you reload
the router.

This section explains how to shut down the Cisco ASR 903 Router. It is recommended that before
turning off all power to the chassis, you issue the reload command. This insures that the operating
system cleans up all the file systems. Once the reload operation is complete, then the
Cisco ASR 903 Router can be powered off safely.
To remove power from the Cisco ASR 903 Router safely, follow this procedure and see the examples:
Step 1
Slip on the ESD-preventive wrist strap that was included in the accessory kit.
Step 2
Enter the reload command.
Step 3
Confirm the reload command.

Rmcp-6ru-1#reload
Proceed with reload? [confirm]
Aug 17 00:06:47.051 R0/0: %PMAN-5-EXITACTION: Process manager is exiting: prs exit
with reload chassis code
Step 4
After confirming the reload command, wait until the system bootstrap message displays before powering
off the system.
System Bootstrap, Version 12.2(33r)XN2, RELEASE SOFTWARE (fc1)
Technical Support: tap://www.cisco.com/techsupport
Copyright (c) 2008 by cisco Systems, Inc.
Current image running: Boot ROM0
Last reset cause: LocalSoft
ASR1000-RP1 platform with 4194303 Kbytes of main memory
mcp-6ru-1-rp0-rommon 1>
5-8
OL-25178-08
Chapter 5

Step 5
Note
Remove any power cables from the Cisco ASR 903 Router.
a.
For power supplies with a circuit breaker switch, position the switch to the Off (O) position.
b.
For power supplies with a Standby switch, place the Standby switch in the Standby position.
After powering off the router, wait a minimum of 30 seconds before powering it on again.

OL-25178-08
5-9
Chapter 5
5-10
OL-25178-08
A P P E N D I X

Use the Site Log to provide a record of actions related to installing and maintaining the router. Keep it
in an accessible place near the chassis so that those who performs tasks have access to it. Use the
Installation Checklist (see the Site Planning section on page 2-10) to verify the steps in the installation
and maintenance of your router. Site Log entries might include the following:
Installation progressMake a copy of the Cisco ASR 903 Router Installation Checklist, and insert
it into the Site Log. Make entries as you complete each task.
Upgrade, removal, and maintenance proceduresUse the Site Log as a record of ongoing router
maintenance and expansion history. Each time a task is performed on the Cisco ASR 903 Router,
update the Site Log to reflect the following:
Removal or replacement of interface modules, fan tray, power supplies, or RSPs
Configuration changes
Maintenance schedules and requirements
Maintenance procedures performed
Intermittent problems
Comments and notes
Table A-1 on page A-2 shows a sample site log. Make copies of the sample or design your own site log
to meet the needs of your site and equipment.

OL-25178-08
A-1
Appendix A
Table A-1
Date
Site Log
Description of Action Performed or Symptom Observed
Initials
A-2
OL-25178-08
Appendix A

Manufactures
Manufactures
Table A-2 lists the manufacturers for equipment used with the Cisco ASR 903 router.
Table A-2
Manufacturer
GAW
Manufactures
Web Site or Phone Number
Products/Model
Gaw Technology
Air Plenum (GAW Part

Number:
404ASR903PLM)
A Gaw Associates, Inc. Company

Toll Free: 877-429-7225
Email: [email protected]
Website: www.GawTechnology.net
Burndy
http://www.burndy.com
Lugs
1. For ordering, visit www.GawTechnology.net

OL-25178-08
A-3
Appendix A
Manufactures
A-4
OL-25178-08
INDEX
electromagnetic pulse
See EMP
airflow
EMP, avoiding
chassis clearance
altitude
2-14
2-16
2-10
auxiliary port
connecting to a modem
3-34 to ??
global parameters, configuring
4-6
back panel
3-6, 3-7
humidity
2-10
cable length, factors determining
2-14
installation
chassis
starting the router
ground connection description

preventing overheating
coaxial cable
2-12
installing
2-16
2-13
4-2
lifting chassis
2-20
interface
commands
numbering
show environment
2-17
show running-config
show startup-config
1-17
Interface Numbering
4-7
IP, router address
1-17
4-6
4-7
configuring
global parameters
reviewing changes
4-6
4-7
log
connecting
site
router to a PC
console port
A-1
?? to 3-28
4-6
M
modifications to configuration, reviewing
E
electrical wiring requirements
4-7
2-12

OL-25178-07
IN-1
Index
startup system
N
numbering
interface
4-2
1-17
temperature sensor
1-17
terminal server connections
4-6
PC
connecting to router
?? to 3-28
power
surge suppression
power lines (warning)
2-14
2-4
power supplies (warning)
2-4
procedures
starting the router
4-2
R
regulatory compliance
1-18
restricted access (warning)
2-4
reviewing changes to configuration

RJ-45 connectors
4-7
2-14
router
connecting to a PC
?? to 3-28
RS-232 asynchronous data
2-14
S
safety
information
1-18
sample configurations, global parameters
4-6
show commands
show running-config
show startup-config
4-7
4-7
show environment command
2-17
site
log
A-1
site requirements, rack-mounting
2-15
IN-2
OL-25178-07

ASR903 HW Install

Uploaded by

Copyright:

Available Formats

ASR903 HW Install

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ASR903 HW Install

Uploaded by

Copyright:

Available Formats

Cisco ASR 903 Router Hardware

Cisco Systems, Inc.

Text Part Number: OL-25178-08

Document Revision History

Obtaining Documentation and Submitting a Service Request

Cisco ASR 903 router Overview

Cisco ASR 903 router Features 1-1

Cisco ASR 903 Router Hardware Installation Guide

Serial Number Label Location

Preparing for Installation

Safety Guidelines 2-1

Installing the Cisco ASR 903 Router

Cisco ASR 903 Router Hardware Installation Guide

Installing the Router in a Rack 3-1

RSP Installation 3-13

Connecting the Cisco ASR 903 Router to the Network 3-30

Uninstalling the Cisco Microsoft Windows USB Driver

Cisco ASR 903 Router Initial Configuration

Checking Conditions Prior to System Startup

Powering Up the Cisco ASR 903 Router 4-2

Configuring the Cisco ASR 903 Router at Startup 4-5

Cisco ASR 903 Router Hardware Installation Guide

Console/Aux RJ45 RS232 Serial Port Pinout

LED Summary 5-8

Site Log and Manufactures

Cisco ASR 903 Router Hardware Installation Guide

Cisco ASR 903 Router Hardware Installation Guide

About this Book

Document Revision History, page ix

Document Audience, page x

Document Organization, page x

Document Conventions, page x

Obtaining Documentation and Submitting a Service Request, page xii

Document Revision History

Added dust cap information. Added supported patch

Added A900 RSP3-200 module and supported

Added A900 RSP3 module supported interface

Added 32 T1/E1 interface module.

Added A900 RSP2 and supported interface modules.

Updated fan tray, power supply connector, dust filter,

Updated supported SFPs for IOS XE Release 3.10S.

Updated supported SFPs for IOS XE Release 3.9(1).

Updated supported SFPs for IOS XE Release 3.9.

Updated supported SFPs for IOS XE Release 3.8.

Cisco ASR 903 Router Hardware Installation Guide

Added material for AC power supply, chassis air flow

Updated supported SFPs for IOS XE Release 3.6.

Added power draw and installation torque values.

First release published.

Chapter 1, Cisco ASR 903 Router

This chapter provides an overview of the

Chapter 2, Preparing for

This chapter provides site preparation guidelines

This chapter describes how to start the

This chapter provides LED and pinout

Appendix A, Site Log and

This provides a site log for tracking the

Commands and keywords and user-entered text appear in bold font.

Elements in square brackets are optional.

Cisco ASR 903 Router Hardware Installation Guide