D811494 ver.

05 02-07-07

I QUADRO COMANDO
GB CONTROL PANEL

F CENTRALE DE COMMANDE
8 027908 288554
D SELBSTÜBERWACHENDE STEUERUNG
E CUADRO DE MANDOS
P QUADRO DE COMANDO

LIBRA-C-MA

ISTRUZIONI D’USO E DI INSTALLAZIONE

INSTALLATION AND USER’S MANUAL
INSTRUCTIONS D’UTILISATION ET D’INSTALLATION
INSTALLATIONS-UND GEBRAUCHSANLEITUNG
INSTRUCCIONES DE USO Y DE INSTALACION
INSTRUÇÕES DE USO E DE INSTALAÇÃO

Via Lago di Vico, 44

36015 Schio (VI)
Tel.naz. 0445 696511
Tel.int. +39 0445 696533
Fax 0445 696522
Internet: www.bft.it
E-mail: [email protected]
 D811494_05
ENGLISH INSTALLATION MANUAL
Thank you for buying this product, our company is sure that you will be more - Limit-switch control inputs
than satisfied with its performance. - Separate inputs for safety devices
This product is supplied with an “Instruction Manual” which should be read - Incorporated rolling-code radio receiver with transmitter cloning
carefully as it provides important information about safety, installation, op- The board is provided with a terminal board which can be pulled out for
eration and maintenance. easier maintenance or replacement. The board is supplied with a series of
This product complies with recognised technical standards and safety regula- pre-wired jumpers to facilitate the installer’s work.
tions. We declare that it is in conformity with the following European Directives: The jumpers relate to the following terminals: 15-17,15-18����������������
, 23-24, 23-25,
89/336/EEC, 73/23/EEC, 98/37/EEC and subsequent amendments. 23-26 and 23-27������������������������������������������������������������
. If the above-mentioned terminals are in use, remove their
respective jumpers.
1) GENERAL SAFETY
WARNING! An incorrect installation or improper use of the product CHECK
can cause damage to persons, animals or things. The LIBRA-C-MA panel carries out a control (check) on the starting relays and
WARNING! Installation must be carried out using the safety devices safety devices (photocells) before carrying out each opening and closing cycle.
and controls prescribed by the EN 12978 Standard. In case of malfunction, check the devices connected for regular operation
• The “Warnings” leaflet and “Instruction booklet” supplied with this and check the wiring.
product should be read carefully as they provide important information
about safety, installation, use and maintenance. 3) TECHNICAL DATA
• Scrap packing materials (plastic, cardboard, polystyrene etc) according Power supply: ...............................................................230V~ ±10% 50Hz*
to the provisions set out by current standards. Keep nylon or polystyrene Mains/low voltage insulation: .......................................... > 2MOhm 500V
bags out of children’s reach. Working temperature: .............................................................. -10 to +55°C
• Keep the instructions together with the technical brochure for future Dielectric strength:…. ................... mains/low voltage 3750V~ per 1 minute
reference. Motor output current: ....................................................................................
• This product was exclusively designed and manufactured for the use with limit switches connected to terminals 5 and 8:..............3.5A+3.5A max
specified in the present documentation. Any other use not specified in with limit switches connected to terminals 24, 25, 26 and 27:...7.5A+7.5A max
this documentation could damage the product and be dangerous. Motor relay commutation current: .......................................................... 10A
• The Company declines all responsibility for any consequences result- Maximum motor power:............................................180W + 180W (24V )
ing from improper use of the product, or use which is different from that Supply to accessories: . .............................. 24V~ (180mA max absorption)
expected and specified in the present documentation.
24V~ V safe (180mA max absorption)
• Do not install the product in explosive atmosphere.
• The construction components of this product must comply with the following Gate-open warning light:................................ N.O. contact (24V~/1A max)
European Directives: 89/336/CEE, 73/23/EEC, 98/37/EEC and subse- Blinker: . .............................................................................. 24V~ 25W max
quent amendments. As for all non-EEC countries, the above-mentioned Dimensions: ...............................................................................see figure 1
standards as well as the current national standards should be respected Fuses: ........................................................................................see figure 2
in order to achieve a good safety level. (* other voltages available on request)
• The Company declines all responsibility for any consequences resulting
from failure to observe Good Technical Practice when constructing clos- BATTERY KIT BT BAT (Fig.6)
ing structures (door, gates etc.), as well as from any deformation which Charging voltage:.............................................................................27.2V
might occur during use. Charging current:............................................................................... 130mA
• The installation must comply with the provisions set out by the following Outside temperature when values were measured:............................. 25°C
European Directives: 89/336/CEE, 73/23/EEC, 98/37/EEC and subsequent Battery capacity:................................................................... 2x (12V 1.2Ah)
amendments. Flat battery protection threshold:.....................................................20.4V
• Disconnect the electrical power supply before carrying out any work on Battery charging time:.................................................................... 12/14 hrs
the installation. Also disconnect any buffer batteries, if fitted. NOTE: In case of operation with battery back up, the outputs to terminals
• Fit an omnipolar or magnetothermal switch on the mains power supply, 11-12 (24 V~) and 13-14 ( Vsafe 24 V~) have a voltage of 24 V , polarised
having a contact opening distance equal to or greater than 3,5 mm. as shown in Fig. 6.
• Check that a differential switch with a 0.03A threshold is fitted just before When installing the BT-BAT kit, check for correct connection of the safety
the power supply mains. devices. When using the BT BAT battery kit, the value of the power supply
• Check that earthing is carried out correctly: connect all metal parts for Faston terminal must be set to 25 V~ on the transformer.
closure (doors, gates etc.) and all system components provided with an
earth terminal. 4) TERMINAL BOARD CONNECTIONS (Fig.3)
• Fit all the safety devices (photocells, electric edges etc.) which are needed WARNING – During the wiring and installation operations, refer to the current
to protect the area from any danger caused by squashing, conveying and standards as well as principles of good technical practice.
shearing. Wires powered at different voltages must be physically separated, or suitably
• Position at least one luminous signal indication device (blinker) where it insulated with at least 1 mm extra insulation. The wires must be clamped by
can be easily seen, and fix a Warning sign to the structure. an extra fastener near the terminals, for example by bands.
• The Company declines all responsibility with respect to the automation All the connection cables must be kept at an adequate distance from the
safety and correct operation when other manufacturers’ components are dissipator.
used.
• Only use original parts for any maintenance or repair operation. WARNING! For connection to the mains, use a multipolar cable with
• Do not modify the automation components, unless explicitly authorised a minimum of 3x1.5mm2 cross section and complying with the previ-
by the company. ously mentioned regulations. ������������������������������������������
For connection to the motors, use a cable
• Instruct the product user about the control systems provided and the with a minimum cross section of 2.5 sq mm, of the type prescribed by
manual opening operation in case of emergency. current standards.
• Do not allow persons or children to remain in the automation opera- For example, if the cable is out side (in the open), it has to be at least
tion area. equal to H07RN-F, but if it is on the inside (or outside but placed in a
• Keep radio control or other control devices out of children’s reach, in plastic cable cannel) it has to be or at least egual to H05VV-F.
order to avoid unintentional automation activation.
• The user must avoid any attempt to carry out work or repair on the automa- 1-2 Single-phase mains power supply 230V~ ±10% (1=L) (2=N)
tion system, and always request the assistance of qualified personnel. 3-4 Connection to motor 2:
• Anything which is not expressly provided for in the present instructions, 3 motor +
is not allowed. 4 motor -
• Installation must be carried out using the safety devices and controls 5 Motor 2 limit switch control for actuators with limit switch control by
prescribed by the EN 12978 Standard. means of 1 wire only (PHOBOS BT, IGEA BT).*
6-7 Connection to motor 1:
2) GENERAL OUTLINE 6 motor +
The LIBRA-C-MA control panel is supplied by the manufacturer with standard 7 motor -
setting. Any alteration must be set by means of the incorporated display 8 Motor 1 limit switch control for actuators with limit switch control by
programmer or by means of universal palmtop programmer. The Control means of 1 wire only (PHOBOS BT, IGEA BT).*
unit completely supports the EELINK protocol. 9-10 Connection to blinker (24V~ 20W max)
Its main characteristics are: 11-12 Output 24V~ 180mA max - supply to photocells or other devices.
- Control of two low-voltage motors up to 40W power 13-14 Output 24V~ V safe 180mA max - supply to photocell transmitters
- Electronic torque setting with obstacle detection with checking function (Fig.3a).

12 - LIBRA-C-MA - Ver. 05
D811494_05

INSTALLATION MANUAL ENGLISH

15-16 START pushbutton (N.O.). - Motor 1 slow-down torque (m1 t slow) [ 45% ]
15-17 STOP pushbutton (N.C.). If not used, leave the bridge 15-17 con- (Advanced parameters ⇒ address 8)
nected. Set the numerical value for slow-down torque of motor 1 between 1%
15-18 Photocell input (N.C.). If not used, leave the bridge 15-18 con- and 99%.
nected. - Motor 2 slow-down torque (m2 t slow) [ 45% ]
15-19 Fault input (N.O.). Input for photocells provided with checking N.O. (Advanced parameters ⇒ address 9)
contact (Fig. 3a). Set the numerical value for slow-down torque of motor 2 between 1%
15-20 Pedestrian pushbutton input (N.O.). Activation is carried out by motor and 99%.
2; if the opening cycle has started (not from pedestrian function), the NOTE: In case of obstacle detection, the Ampere-stop function halts
pedestrian command has no effect. the leaf movement, reverses its motion for 1 sec. and then halts in
21-22 Output for gate-open warning light output (N.O. contact (24V~/1A the STOP status.
max)) or alternatively 2nd radio channel (see paragraph 6 on “Con- WARNING: Check that the impact force value measured at
figuration”). the points established by the EN 12445 standard is lower than
23 Limit switch common terminal that specified in the EN 12453 standard.
24 Motor 2 opening limit switch for actuators with separate limit switches* Incorrect sensitivity setting can cause injuries to persons or
25 Motor 2 closing limit switch for actuators with separate limit switches* animals, or damage to things.
26 Motor 1 opening limit switch for actuators with separate limit switches* - Opening delay time (open delay time) [ 1s ]
27 Motor 1 closing limit switch for actuators with separate limit switches* Set the opening delay time for motor 1 relative to motor 2, between 1 and
29-30 Antenna input for radio-receiver plug-in board (29 signal–30 braid). 10 seconds.
* When using the limit switches connected to terminals 5 and 8, leave the - Closing delay time (cls delay time) [ 1s ]
jumpers at terminals 24-25-26-27. When using the limit switches connected to Set the closing delay time for motor 2 relative to motor 1, between 1 and
terminals 24-25-26-27, provide jumpers between terminals 5-15 and 8-15. 25 seconds.
Motor 1 fast time��(m1 fast time) [ 15s ]
- �������������������
5) PROGRAMMING (Advanced parameters ⇒ address 6)
The control panel provided with a microprocessor is supplied with function Set the time to normal speed (not slowed down), ranging from 1 to 30
parameters preset by the manufacturer, suitable for standard installations.The seconds. ������������������������������������������������������������������
Carry out the settings from the gate-closed position; if settings
predefined parameters can be altered by means of either the incorporated are carried out from a different point, they will become effective as from
display programmer or universal palmtop programmer. the subsequent opening manoeuvre.
In the case where programming is carried out by means of universal palmtop Motor 2 fast time��(m2 fast time) [ 15s ]
- �������������������
programmer, carefully read the instructions relating to universal palmtop (Advanced parameters ⇒ address 7)
programmer, and proceed in the following way. Set the time to normal speed (not slowed down), ranging from 1 to 30
Connect the universal palmtop programmer to the control unit through the seconds. ������������������������������������������������������������������
Carry out the settings from the gate-closed position; if settings
UNIFLAT and UNIDA accessories (See fig. 4). The LIBRA-C-MA control unit are carried out from a different point, they will become effective as from
does not supply the universal palmtop programmer with power, and therefore the subsequent opening manoeuvre.
requires an appropriate supply unit. Note: The slow-down time, on closing and on opening, is obtained by
Enter the “CONTROL UNITS” menu, and the “PARAMETERS” submenu, then timing one manoeuvre and setting a minimum value for this parameter.
scroll the display screenfuls using the up/down arrows to set the numerical If, for example, one manoeuvre lasts 25 seconds, a setting of “normal
values of the parameters listed below. speed time” to 20s will produce a slow-down time of 5s both on closing
For the function logics, refer to the “LOGIC” submenu. and on opening.
In the case where programming is carried out by means of the incorporated - Slow-down speed (slov speed) [ 50% ]
programmer, refer to Fig. A and B and to the paragraph on “Configuration”. (Advanced parameters ⇒ address 5)
Set the slow-down speed:
6) CONFIGURATION Sets the slow-down speed percentage between 0% and 99% of normal
The display programmer is used to set all the LIBRA-C-MA control panel speed.
functions. �������������������������������������
0 – slow-down disabled ��������������
(always fast).
The programmer is provided with three pushbuttons for menu scrolling and - Zone (zone) [ 0 ]
function parameter configuration: Set the zone number between a minimum value of 0 and a maximum
+ menu scrolling/value increment key value of 127. See paragraph 7 on “Serial connection”.
- menu scrolling/value reduction key
OK Enter (confirm) key 6.2) LOGIC MENU (logic.)
The simultaneous pressure of the + and - keys is used to exit the active - TCA (TCA) [ OFF ]
menu and move to the preceding menu. ON : Activates automatic closing
The modifications made are only set if the OK key is subsequently pressed. OFF:Excludes automatic closing
When the OK key is pressed for the first time, the programming mode is - 3 Steps (3 step) [ OFF ]
entered. ON: Enables 3-step logic. A Start impulse has the following effects:
The following pieces of information appear on the display at first: door closed:.................................................................................opens
- Control unit software version on opening:..................................stops and enters TCA (if configured)
- Number of total manoeuvres carried out (the value is expressed in door open: . ................................................................................ closes
thousands, therefore the display constantly shows 0000 during the first on closing:................................................................stops and reopens
thousand manoeuvres) OFF:Enables 4-step logic. A Start impulse has the following effects:
- Number of manoeuvres carried out since the latest maintenance opera- door closed:.................................................................................opens
tion (the value is expressed in thousands, therefore the display constantly on opening:..................................stops and enters TCA (if configured)
shows 0000 during the first thousand manoeuvres) door open: . ................................................................................ closes
- Number of memorised radio control devices. on closing:....................................stops and does not enter TCA (stop)
When the OK key is pressed during the initial presentation phase, the first after stopping:..............................................................................opens
menu can be accessed directly. - Impulse lock (ibl open) [ OFF ]
Here follows a list of the main menus and the respective submenus available. ON : The Start impulse has no effect during the opening phase.
The predefined parameter is shown between square brackets [ 0 ]. OFF:The Start impulse becomes effective during the opening or closing phase.
The writing appearing on the display is indicated between round brackets. - Rapid closing (fast cls) [ OFF ]
Refer to Figures A and B for the configuration procedure. ON: Closes the gate after 3 seconds from photocell disengagement
before waiting for the end of the TCA set.
6.1) PARAMETER MENU (PARAm) OFF:Command not entered.
- Automatic Closing Time (TCA) [ 10s ] - Photocells on opening (photc. open) [ OFF ]
Set the numerical value of the automatic closing time from 3 to 120 (Advanced logics ⇒ address 14)
seconds. ON: In case of obscuring, this excludes photocell operation on opening.
- Motor 1 torque (Mot1 torque) [ 50% ] During the closing phase, it immediately reverses the motion.
(Advanced parameters ⇒ address 3) OFF:In case of obscuring, the photocells are active both on opening and on
Set the numerical value of the motor 1 torque between 1% and 99%. closing. When a photocell is obscured on closing, it reverses the motion
- Motor 2 torque (Mot 2 torque) [ 50% ] only after the photocell is disengaged.
(Advanced parameters ⇒ address 4) - Photocell test (test phot) [ OFF ]
Set the numerical value of the motor 2 torque between 1% and 99%. ON: Activates photocell check
OFF:Deactivates photocell check

LIBRA-C-MA - Ver. 05 - 13
 D811494_05
ENGLISH INSTALLATION MANUAL
If this setting is not activated (OFF), it inhibits the photocell checking - Read (read)
function, allowing connection of devices not provided with additional Checks one key of a receiver; if stored it displays a message showing
checking contact. the receiver number in the memory location (from 01 to 64), and the key
- Gate-open or 2nd radio channel warning light (SCA 2ch) [ OFF ] number (T1, T2, T3 or T4).
ON: The output between terminals 21 and 22 is configured as Gate-open - Eliminate list (erease 64)
warning light, in this case the 2nd radio channel controls pedestrian WARNING! Completely removes all memorised radio control devices
opening. from the receiver memory.
OFF:The output between terminals 21 and 22 is configured as 2nd radio - Receiver code reading (RX code)
channel. This displays the code entered in the receiver (par. 11).
- Motors in operation (1 mot ON) [ OFF ] Consult paragraphs 8, 9, 10 and 11 for further information concerning
ON: Only motor 2 is in operation (terminals 3, 4 and 5). the advanced functions of the Clonix incorporated receiver.
With this configuration, the pedestrian input is disabled.
OFF:Both motors are in operation. 6.4) LANGUAGE MENU (language)
- Lock hold (block persist) [ OFF ] (Fig. 5) Allows you to set the language on the display programmer.
ON: To be used when the mechanical closing backstop is fitted. - ITALIAN (ITA)
This function activates leaf pressure on the mechanical backstop, without - FRENCH (FRA)
this being considered as an obstacle by the Ampere-stop sensor. - GERMAN (DEU)
Therefore the rod continues its travel for another 0.5 sec. after detecting - ENGLISH (ENG)
the closing limit switch or upon reaching the mechanical backstop. So - SPANISH (ESP)
by activating the closing limit switches slightly earlier, the leaves will
come to a perfect halt against the backstop. (Fig. 5a) 6.5) DEFAULT MENU (default)
OFF:To be used when no mechanical closing backstop is fitted. Restores the preset default values on the control unit. After restoring, a new
Movement is exclusively halted by activation of the closing limit switches; autoset operation must be carried out.
in this case proceed to carrying out precise setting of the closing limit-
switch activation. (Fig. 5b) 6.6) DIAGNOSTICS AND MONITORING
- Hold-to-run control (hold-to-run) [ OFF ] The display on the LIBRA-C-MA panel shows some useful information, both
ON: Hold-to-run operation: the manoeuvre continues as long as the control during normal operation and in the case of malfunctions.
key is kept pressed. Diagnostics:
WARNING!: Enabling the Hold-to-run logic entails a different use of the In the case of malfunctions, the display shows a message indicating which
START and PEDESTRIAN buttons: device needs to be checked:
START takes on the hold-to-run OPEN function STRT = START input activation
PEDESTRIAN takes on the hold-to-run CLOSE function STOP = STOP input activation
OFF:Impulse operation, according to the 3 or 4 step logic. PHOT = PHOT input activation
- Fixed code (fixed code) [ OFF ] FLT = FAULT input activation for checked photocells
(Advanced logics ⇒ address 13) TH = Activation of software thermal protection
ON: The receiver is configured for operation in fixed-code mode, see para- ER 1 = Board error during safety device check
graph on “Radio Transmitter Cloning”. ER 2 = Board error during safety device check
OFF:The receiver is configured for operation in rolling-code mode, see When using traditional limit switches connected to terminals 24-25-26-27:
paragraph on “Radio Transmitter Cloning”. SWO1 = activation of Motor 1 opening limit switch input
- Radio transmitter programming (radio prog) [ ON ] SWC1 = activation of Motor 1 closing limit switch input
(Advanced logics ⇒ address 15) SWO2 = activation of Motor 2 opening limit switch input
ON: This enables transmitter storage via radio: SWC2 = activation of Motor 2 closing limit switch input
1 – First press the hidden key (P1) and then the normal key (T1, T2, T3 In the case where an obstacle is found, the LIBRA-C-MA panel stops the
or T4) of a transmitter already memorised in standard mode by means door and activates a reverse manoeuvre; at the same time the display shows
of the radio menu. the “AMP” message.
2 – Within 10s press the hidden key (P1) and the normal key (T1, T2,
T3 or T4) of a transmitter to be memorised. Monitoring:
The receiver exits the programming mode after 10s, other new transmit- During the opening and closing phases, the display shows four digits sepa-
ters can be entered before the end of this time. rated by a dot, for example 35.40. The digits are constantly updated during
This mode does not require access to the control panel. the manoeuvre, and represent the maximum torque reached by motor 1
OFF:This disables transmitter storage via radio. (35) and motor 2 (40).
The transmitters can only be memorised using the appropriate Radio These values allow the torque setting to be corrected.
menu. If the maximum torque value reached during the manoeuvre gets sensibly
- Master/Slave (Master) [ OFF ] close to the value set in the parameter menu, malfunctions may occur in the
ON: The control panel is set as Master in a centralised connection (see future following wear or slight door deformation.
Paragraph 7). It is therefore advisable to check the maximum torque reached during some
OFF:The control panel is set as Slave in a centralised connection (see of the manoeuvres carried out in the course of installation, and if necessary
Paragraph 7). set a value about 15-20 percent points higher in the parameter menu.
- Start-Open selection (start - open) [ OFF ]
ON: The input between the two terminals 15-16 acts as open. For closing, 6.7) ADJUSTING PROCEDURE
wait until the TCA, which has to be previously enabled, has elapsed. - Before switching on, check electrical connections.
OFF:The input between the two terminals 15-16 acts as start. - Set the following parameters: Automatic Closing Time, Opening and closing
- Prealarm (pre-alarm) [ OFF ] delay times, Slow-down speed and Zone number.
ON: The blinker comes on 3 sec. before the motors start. - Set all the logics.
OFF:The blinker comes on at the same time as the motors start. - Carry out the autoset procedure.
- Automatic fast time (auto fast time) [ ON ] After completing the autoset procedure, the Motor fast time and the Torque
ON: The control unit automatically calculates slow-down time and offsets fast can be manually adjusted.
time to keep slow-down time constant. With this function active, the fast WARNING! Any incorrect setting can cause injuries to persons and
time value is continually updated (it is therefore possible to find a setting animals or damage to things.
other than the one actually carried out). WARNING: Check that the impact force value measured at
OFF:The control unit does not offset fast time, but applies the preset «fast time» the points established by the EN 12445 standard is lower than that
parameter, independently of any environmental changes. specified in the EN 12453 standard.
To obtain a better result, it is advisable to carry out the autoset procedure
6.3) RADIO MENU (RADIO) and the fast time setting with the motors at rest (i.e. not overheated by a
- Add considerable number of consecutive manoeuvres).
Allows you to add one key of a radio control device to the receiver memory;
after storage it displays a message showing the receiver number in the 6.8) AUTOSET MENU (autoset)
memory location (from 01 to 64). Allows you to automatically set the Motor torque.
Add Start button (add start) WARNING! The autosetting operation is carried out from closing end-of-
associates the required key to Start command stroke devices. If Autoset is commanded in a different position an error
Add 2ch button (add 2ch) message indicating “nsvc” will be displayed and the required manoeuvre
associates the required key to 2nd radio channel will not take place.

14 - LIBRA-C-MA - Ver. 05
D811494_05

INSTALLATION MANUAL ENGLISH

WARNING!! The autoset operation is only to be carried out after checking the PROGRAMMING
exact leaf (opening/closing) movement, and correct limit-switch activation. Transmitter storage can be carried out in manual mode or by means of
Set the adequate slow-down speed: by pressing OK the message “.... .... ....” the universal palmtop programmer which allows the complete installation
is displayed and the control unit commands an opening manoeuvre without database to be managed through the Eedbase software.
slow-down, followed by a closing manoeuvre without slow-down during which In this second case, receiver programming takes place through the connection
the duration of the stroke is memorised. Then, the control unit commands a of universal palmtop programmer to the LIBRA-C-MA control panel, using
second opening manoeuvre with slow-down followed by a second closing the UNIFLAT and UNIDA accessories as indicated in Fig. 4.
manoeuvre with slow-down during which the minimum torque value neces-
sary for the movement of the leaf is automatically set. 10) MANUAL PROGRAMMING
During this phase, it is important to avoid obscuring the photocells, as well as In the case of standard installations where advanced functions are not
using the START, STOP, PED, CLOS or OPEN commands and the display. required, you can proceed to manual storage of the transmitters, making
After completion, if the Autoset was successful, an “OK” message will be reference to fig. B for basic programming.
displayed on the control unit which will then return to the Autoset menu after - If you wish the transmitter to activate output 1 (START) by means of key1,
pressing the “OK” key. key2, key3 or key4, enter the transmitter in menu “Start key”, as in fig. B.
If, on the other hand, the control unit displays the “KO” message, it means - If you wish the transmitter to activate output 2 (2nd radio channel relay)
that the autoset procedure has not been successfully completed; it is thus by means of key1, key2, key3 or key4, enter the transmitter in menu “2nd
necessary to check the wear condition of the gate and the regular movement ch. key”, as in fig. B.
of the leaves before proceeding to a new autoset operation. Note: Hidden key P1 appears differently depending on the transmitter
WARNING! During the autoset phase, the obstacle detection function is model.
not active, therefore the installer must control the automation movement For transmitters with hidden key, press hidden key P1 (fig. B1). For transmit-
and prevent persons and things from approaching or standing within the ters without hidden key, the key P1 function corresponds to simultaneously
automation working range. pressing the 4 transmitter keys or, after opening the battery compartment,
In the case where buffer batteries are used, autosetting must be carried out bridging the two P1 points by means of a screwdriver (fig. B2).
with the control panel supplied by mains power voltage.
WARNING: The torque values fixed by means of the autoset pro- IMPORTANT NOTE: ATTACH THE ADH ESIVE KEY LABEL TO THE FIRST
cedure refer to the slow-down speed fixed during the same pro- MEMORISED TRANSMITTER (MASTER).
cedure. If the slow-down speed is changed, a new autoset procedure In the case of manual programming, the first transmitter assigns the key
must be carried out. code to the receiver; this code is necessary in order to carry out subsequent
WARNING: Check that the impact force value measured at the cloning of the radio transmitters.
points established by the EN 12445 standard is lower than that
specified in the EN 12453 standard. 11) RADIO-TRANSMITTER CLONING
Incorrect sensitivity setting can cause injuries to persons or Rolling-code cloning / Fixed-code cloning
animals, or damage to things. Make reference to the universal palmtop programmer Instructions and the
CLONIX Programming Guide.
7) Statistics
Having connected the universal palmtop programmer to the control unit, enter 11.1) ADVANCED PROGRAMMING: COLLECTIVE RECEIVERS
the CONTROL UNIT / STATISTICS menu and scroll the screenful showing Make reference to the universal palmtop programmer Instructions and the
the statistical parameters: CLONIX Programming Guide.
- Board microprocessor software version.
- Number of cycles carried out. If motors are replaced, count the number 12) SERIAL CONNECTION USING SCS1 BOARD (Fig.6)
of manoeuvres carried out up to that time. The LIBRA-C-MA control panel allows several automation units (SCS1) to
- Number of cycles carried out from the latest maintenance operation. be connected in a centralised way by means of appropriate serial inputs
It is automatically set to zero after each self-diagnosis or parameter and outputs. This makes it possible to use one single command to open and
writing. close all the automation units connected.
- Date of latest maintenance operation. To be updated manually from the Following the diagram in Fig.6, proceed to connecting all the LIBRA-C-MA
appropriate menu “Update maintenance date”. control panels, exclusively using a telephone-type line.
- Installation description. 16 characters can be entered for installation Should a telephone cable with more than one pair be needed, it is indispens-
identification. able to use wires from the same pair.
The length of the telephone cable between one appliance and the next must
8) INTEGRATED RECEIVER TECHNICAL SPECIFICATION not exceed 250 m.
Receiver output channels: At this point, each of the LIBRA-C-MA control panels must be appropriately
- output channel 1, if activated, controls a START command. configured, by setting a MASTER unit first of all, which will have control over
- output channel 2, if activated, controls the excitation of the 2nd radio all the others, to be necessarily set as SLAVE (see logic menu). The
�����������
MASTER
channel relay for 1s. control unit must be the first one of the series (Fig. 6).
Transmitter versions which can be used: Also set the Zone number (see parameter menu) between 0 and 127.
all Rolling Code transmitters compatible with . The zone number allows you to create groups of automation units,
each one answering to the Zone Master unit. Each zone can only be
ANTENNA INSTALLATION assigned one Master unit, the Master unit in zone 0 also controls the Slave
Use an antenna tuned to 433MHz. units in the other zones.
For Antenna-Receiver connection, use RG8 coaxial cable.
The presence of metallic masses next to the antenna can interfere with radio 13) SCRAPPING
reception. In case of insufficient transmitter range, move the antenna to a Warning: This operation should only be carried out by qualified person-
more suitable position. nel. Materials must be disposed of in conformity with the current regulations.
9) RECEIVER CONFIGURATION In case of scrapping, the automation devices do not entail any particular risks
The on-board receiver combines characteristics of utmost safety in copying or danger. In case of materials to be recycled, these should be sorted out by
variable code (rolling code) coding with the convenience of carrying out type (electrical components, copper, aluminium, plastic etc.).
transmitter “cloning” operations thanks to an exclusive system.
Cloning a transmitter means creating a transmitter which can be automatically 14) DISMANTLING
included within the list of the transmitters memorised in the receiver, either Warning: This operation should only be carried out by qualified person-
as an addition or as a replacement of a particular transmitter. nel. When the control unit is disassembled to be reassembled on another
Cloning by replacement is used to create a new transmitter which takes site, proceed as follows:
the place of the one previously memorised in the receiver; in this way a • Disconnect the power supply and the entire electrical installation.
specific transmitter can be removed from the memory and will no longer • In the case where some of the components cannot be removed or are
be usable. damaged, they must be replaced.
Therefore it will be possible to remotely program a large number of additional
transmitters or, for example, replacement transmitters for those which have The descriptions and illustrations contained in the present manual are
been lost, without making changes directly to the receiver. not binding. The Company reserves the right to make any alterations
When coding safety is not a decisive factor, the on-board receiver allows deemed appropriate for the technical, manufacturing and commercial
you to carry out fixed-code additional cloning which, although abandoning improvement of the product, while leaving the essential product fea-
the variable code, provides a high number of coding combinations, there- tures unchanged, at any time and without undertaking to update the
fore keeping it possible to “copy” any transmitter which has already been present publication.
programmed.

LIBRA-C-MA - Ver. 05 - 15
 D811494_05

16 - LIBRA-C-MA - Ver. 05
D811494_05

LIBRA-C-MA - Ver. 05 - 17
 D811494_05
Fig. 1 Fig. 2

10 F1A25T
194 0

29 30
236

SD 1 2 3 4 5 6 7 8 9 10 1112131415 1617181920 21 22 23 24 25 26 27 28

F 1AT (230V)
F 2AT (110V)

OK

Fig. 3

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
FC M2*

FC M1*

COM

START

PED
STOP

PHOT

FAULT

COM FC

FCA M2

FCC M2

FCA M1

FCC M1

ANT

SHIELD
25W max.
+

L N M2 M1
NO

NO

NO
NC

NC

230V ~
ANT.
24V ~ 24V ~
* Controllo finecorsa negli attuatori con VSafe
gestione finecorsa con 1 solo filo
(PHOBOS BT, IGEA BT).

* Limit switch control for actuators with Fig. 3a

limit switch control by means of 1 wire
only (PHOBOS BT, IGEA BT).
SCA
*Contrôle fin de course dans les
a c t i o n n e u r s ave c g e s t i o n d e f i n d e 11 12 21 22 11 12 13 14 15 16 17 18 19 20 11 12 13 14 15 16 17 18 19 20
course avec un seul fil (PHOBOS BT,
24 V~

24V ~

COM

PHOT

FAULT

24V ~

COM

PHOT

FAULT
24V ~VSafe

24V ~VSafe

IGEA BT).

* Endschalter-Kontrolle in Antrieben mit

1-Draht-Endschaltersteuerung
(PHOBOS BT, IGEA BT).

* Control de los fines de carrera en los

servomotores con gestión de los fines 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5
de carrera con 1 solo hilo (PHOBOS
BT, IGEA BT). 19 20 21 22 Rx 1 Rx 1 Rx 2

1 2 1 2 1 2
*C o n t r o l o d o f i m - d e - c u r s o n o s Tx 1 Tx 1 Tx 2

accionadores com gestão do fim-de-curso

com 1 único fio (PHOBOS BT, IGEA BT).

42 - LIBRA-C-MA - Ver. 05
D811494_05

Fig. 3a

LIBRA-C-MA SCS1-MA LIBRA-C-MA SCS1-MA

11 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6 11 12 13 14 15 16 17 18 19 20 1 2 3 4 5 6

COM
24V ~

24V ~VSafe
24V ~

FAULT

FAULT
PHOT

PHOT
24V ~VSafe

COM
24V ~VSafe
24V ~

24V ~VSafe
24V ~
18 5 18 5 4-SCS1-MA 5
15 4 2 14 15 4 2 14 5-SCS1-MA 4 2 14
3 1 13 3 1 13 3-SCS1-MA 3 1 13
12 2 12 2 12 2
15 5
11 1 11 1 11 1
Rx 1 Tx 1 19 4 2 14 Rx 1 Tx 1 Rx 3 Tx 3
3-SCS1-MA 3 1 13
12 2
1-SCS1-MA 5 11 1 1-SCS1-MA 5 15 5
2-SCS1-MA 4 Rx 3 Tx 3 2-SCS1-MA 4 19 4 2 14
3 2 14 3 2 14 6-SCS1-MA 3 1 13
12 2 1 13 12 2 1 13 12 2
11 1 11 1 11 1
Rx 2 Tx 2 Rx 2 Tx 2 Rx 4 Tx 4

Fig. 4

Programmatore palmare universale

Universal palmtop programmer
Programmateur de poche universel
Universellen Palmtop-Programmierer
Programador de bolsillo universal
Programador palmar universal

UNIPOWER

Contatti
Contacts
UNIFLAT Contacts
Kontakte
Contactos
Contatos
UNIFLAT
Contatti
Contacts
Contacts UNITRC UNIFLAT
Kontakte
Contactos
Contatos

UNIMITTO UNITRC P1

Contatti
Contacts T1 P1
T1 2
Contacts T2 T 3
Kontakte Led T 4
T
Contactos
Contatos
P1 P1

P1

UNIMITTO UNITRC

2 2
1
1
Contatti
Contacts
Contacts
Kontakte
P1 Contactos
Contatos
3 4 3 4

LIBRA-C-MA - Ver. 05 - 43
 Fig. 5

0,5s
A
B
Fig. 6

LIBRA-C-MA

SCS1

SBS
230V
(*)

33
33
44 25V

55 33 (*) 110V

LIBRA-C-MA

o
11 12 13 14 15 16 17 18 19 20

elh m
12V, 1.2 AH

Ver
COM

START

PED
STOP

PHOT

FAULT

e-Rot-Rojo
--

Roug
++

ed-
+ - + -

o-R
NO

NO

NO
NC

NC

6 12V, 1.2 AH
SBS 55

ss
5 Ro
4 44
JP1 3 33
--
24V= 24V= 2
1 ++
VSafe

MASTER
SCS1 SCS1 SCS1
RX1
RX2

RX1
RX2

RX1
RX2
TX1
TX2

TX1
TX2

TX1
TX2

Max. 250m