AM5888S

Motor Driver ICs

5-channel BTL Driver for DVD player

AM5888S
The AM5888S is a five-channel BTL driver IC for driving the motors and actuators such as used in DVD player and
consists of two independent precision voltage regulators with adjustable range from 1.5V to 4 V. It supports a
variety of applications. Also, Pb free package is selectable (Please refer to Marking Identification).

Applications
BTL driver for CD, CD-ROM and DVD.

Features
1) Two channels are voltage-type BTL drivers for 8) Sled motor driver:
actuators of tracking and focus. Two channels are A general purpose input OP provides differential
voltage-type BTL driver for sled and spindle input for signal addition. The output structure is
motors. It is also built-in one channel bi-direction one power OPAMP in bridge configuration.
DC motor driver for tray. 9) Spindle driver:
2) Wide dynamic range [9.0V (typ.) when Vcc1= Single input linear BTL driver. The output
Vcc2= 12V, at RL= 20 load]. structure are two power OPAMPS in bridge
3) Separating power of Vcc1 and Vcc2 is to configuration.
improve power efficiency by a low supply 10) Tray in-out driver:
voltage for tracking, focus, and spindle. The DC motor driver supports forward/reverse
4) Level shift circuit built-in. control for tray motor.
5) Thermal shut down circuit built-in. 11) 2 Built-in regulator controllers
6) Mute mode built-in. Adjustable range 1.5V ~ 4V
7) Dual actuator drivers:
A general purpose input OP provides differential
input for signal addition. The output structure is
two power OPAMPS in bridge configuration.

AMtek SEMICONDUCTORS -1- Nov 2004 V1.1

 AM5888S
Motor Driver ICs

Absolute maximum ratings (Ta=25C)

Parameter Symbol Limits Unit

Vcc1
Supply voltage 13.5 V
Vcc2
Power dissipation *1.7 Pd W
Operate Temp range -35 ~ +85
Topr
Storage Temp range **-55 ~ +150
Tstg
*When mounted on a 70mm70mm1.6mm glass epoxy board.
*Reduced by 13.6mW for each increase in Ta of 1 over 25.
**Should not exceed Pd or ASO and Tj=150C values

Guaranteed operating conditions (Ta=25C)

Parameter Symbol Limits Unit

Vcc1 4.3 ~ 13.2 V
Power supply voltage
Vcc2 4.3 ~ Vcc1 V

Block diagram

MUTE BIAS VINTK TRB_2 NC VINLD GND VCTL NC VCC2 VOLD- VOLD+ VOTK- VOTK+

28 27 26 25 24 23 22 21 20 19 18 17 16 15
GND PGND

Vcc2
10K
15K
MUTE
10K

+ - Spindle Actuator
-

+
Driver(4X) Driver(6x)
-

25K
+

Thermal
Shut down
Vcc2
Vcc2
Vcc1
25K 10K
+

-
+
-

25K Sled Actuator

+ Driver(4X) Driver(6x)
-

Pre-DRV TRAY
Vcc1
DRIVER
PGND
10K

1 2 3 4 5 6 7 8 9 10 11 12 13 14
VINFC TRB_1 REGO2 VINSL+ REGO1 FWD REV VCC1 VOTR- VOTR+ VOSL+ VOSL- VOFC- VOFC+

AMtek SEMICONDUCTORS -2- Nov 2004 V1.1

 AM5888S
Motor Driver ICs

Electrical characteristics
( Unless otherwise specified Ta=25, Vcc1=12V, Vcc2=5V, BIAS=2.5V, RL=8/10/20/45)

Limit
Parameter Symbol Unit Conditions P.S
Min Typ Max
Quiescent current Icc - 30 - mA
Voltage for mute ON Vston 0 - 0.5 V
Voltage for mute OFF Vstoff 2.0 - 5 V
<Actuator drivers>
Output offset voltage Voo - - 50 mV
Maximum output voltage Vom 3.6 4.0 - V @10Load
Voltage gain Gv 21.5 23.5 25.5 dB VIN=BIAS+0.2Vpp ac @1KHz
<Sled motor driver>
Output offset voltage Voofsl - - 100 mV
Maximum output voltage Vomsl 7.5 9.0 - V @20 Load
Closed loop voltage gain Gvsl 18 20 22 dB VIN=BIAS+0.2Vpp ac @1KHz
<Spindle motor driver>
Output offset voltage Voofld - - 50 mV
Maximum output voltage Vomax - 3.5 - V @8 Load
Voltage gain Gvld 13.3 15.5 17.5 dB VIN=BIAS+0.2Vpp ac @1KHz
Gain error by polarity Gvld 0 1 2 dB VIN=BIAS+0.2Vpp ac @1KHz
<Tray motor driver>
Output saturation voltage 1 Upper + Lower saturation,
VSAT1 0.7 1.1 1.5 V
IL=200mA
Output saturation voltage Output saturation voltage 1
VSAT1 - - 0.1 V
between F&R between FWD and REV
Output saturation voltage 2 Upper + Lower saturation,
VSAT2 1.0 1.55 2.2 V
IL=500mA
Output adjustable gain on H
VVtrH 7.4 9.2 11 dB VCTL=2V
side voltage
<Tray motor driver input logic>
High level input voltage VIH 1.5 - Vcc V
Low level input voltage VIL -0.3 - 0.5 V
High level input current IIH - 180 270 A VFWD=VREV=5V
<Regulator> **
Output voltage Vreg 1.5 4.0 IL = 500mA ***
Output load differential VRL -50 0 50 mV IL = 0~500mA
Power supply voltage VVCC -25 0 25 mV (Vcc=4.5~8V) IL = 500mA
differential

*This device is not designed for protection against radioactive rays.

** It is based on 8550C PNP application
*** It is based on 8550D

AMtek SEMICONDUCTORS -3- Nov 2004 V1.1

 AM5888S
Motor Driver ICs

Pin configuration

VINFC 1 28 MUTE

TRB_1 2 27 BIAS

REGO 2 3 26 VINTK

VINSL+ 4 25 TRB_2

REGO 1 5 24 NC
AM5888S
FWD 6 23 VINLD

REV 7 22 GND

Vcc1 8 21 VCTL

VOTR- 9 20 NC

VOTR+ 10 19 Vcc2

VOSL+ 11 18 VOLD-

VOSL- 12 17 VOLD+

VOFC- 13 16 VOTK-

VOFC+ 14 15 VOTK+

AMtek SEMICONDUCTORS -4- Nov 2004 V1.1

 AM5888S
Motor Driver ICs

Pin description

PIN No Pin Name Function

1 VINFC Input for focus driver
2 TRB_1 Connect to external transistor base
3 REGO2 Regulator voltage output, connect to external transistor collector
4 VINSL+ Input for the sled driver
5 REGO1 Regulator voltage output, connect to external transistor collector
6 FWD Tray driver forward input
7 REV Tray driver reverse input
8 Vcc1 Vcc for pre-drive block and power block of sled and tray
9 VOTR- Tray driver output (-)
10 VOTR+ Tray driver output (+)
11 VOSL+ Sled driver output (+)
12 VOSL- Sled driver output (-)
13 VOFC- Focus driver output (-)
14 VOFC+ Focus driver output (+)
15 VOTK+ Tracking driver output (+)
16 VOTK- Tracking driver output (-)
17 VOLD+ Spindle driver output (+)
18 VOLD- Spindle driver output (-)
19 Vcc2 Vcc for power block of spindle, tracking and focus
20 NC No Connection
21 VCTL Speed control input of tray driver
22 GND Ground
23 VINLD Input for spindle driver
24 NC No Connection
25 TRB_2 Connect to external transistor base
26 VINTK Input for tracking driver
27 BIAS Input for reference voltage
28 MUTE Input for mute control
Notes) Symbol of + and (output of drivers) means polarity to input pin.
(For example, if voltage of pin1 is high, pin14 is high.)

AMtek SEMICONDUCTORS -5- Nov 2004 V1.1

 AM5888S
Motor Driver ICs

Power dissipation curve :

Pd (W)

2.0

1.5

1.0

25 50 75 100 125 150 Ta()

*70mm70mm1.6mm glass epoxy board.
*De-rating is done at 13.6mW/ for operating above Ta=25

Operation notes

1) The built-in thermal shutdown circuit mutes the output current when the chip temperature reaches 175
(typ.). The hysteresis is set to 25 (typ.), so the circuit will start up again when the chip temperature falling
to 150 (typ.).
2) In case mute pin voltage is under 0.5V or NC, output current is muted (except for tray motor driver). Mute
pin voltage should be more than 2.0V for normal application.
3) Bias pin (pin 27) should be pulled up to more than 1.2V. In case the bias pin voltage is pulled down below
0.9V (typ.), the output current is muted.
4) Insert the bypass capacitor (~ 0.1uF ) between Vcc pin and GND pin as close as possible.
5) Heat dissipation fins are attached to the GND on the inside of the package. Make sure to connect them to the
external GND.
6) NC pins ( 20, 24 ) are reserved for internal test. Please keep them floating.

AMtek SEMICONDUCTORS -6- Nov 2004 V1.1

 AM5888S
Motor Driver ICs

7) Tray driver logic input:

FWD (pin6) REV (pin7) VOTR+ (pin10) VOTR- (pin9) Function

L L OPEN OPEN Open mode
L H L H Reverse mode
H L H L Forward mode
H H L L Brake mode
Input circuit of pin6 and pin7 is designed to avoid simultaneous activation of upper and lower
output tr. ; however, in order to improve reliability, apply motor forward/reverse input once through
open mode.
We recommend time period for open longer than 10msec.

H side Output voltage on output voltage (VOL+, VOL-) varies depending on output control
terminal for tray (pin21). H side output voltage is set three times (9.2dB Typ.) VTCL(pin21). And,
L side output voltage is equal to output saturation voltage.

Application circuit

SERVO U-COM
Tracking

Vcenter

Spindle
MUTE
Focus

FWD
REV
Sled

5v or 12V
voltage
control
Tray
5V

M Tracking coil
NC NC

28 27 26 25 24 23 22 21 20 19 18 17 16 15
GND PGND

Vcc2
10K
15K
MUTE
10K
+ - Spindle Actuator
-

+
Driver(4X) Driver(6x)
-

25K
Thermal
Shut down
Vcc2
Vcc2
Vcc1
25K 10K
+

-
+
-

25K Sled Actuator

+
Driver(4X) Driver(6x)
-

Pre-DRV TRAY
Vcc1
DRIVER
PGND
10K

1 2 3 4 5 6 7 8 9 10 11 12 13 14
10K

10K

M M
12V Focus coil
16.4K

10K
47uF

5V
REGOUT
ADJ 2.5V

REGOUT
ADJ 3.3V

47uF

AMtek SEMICONDUCTORS -7- Nov 2004 V1.1

 AM5888S
Motor Driver ICs

Testing circuit

V23
5V

8 10
V28 V27 V26 V19

NC OPEN NC

28 27 26 25 24 23 22 21 20 19 18 17 16 15
GND PGND

Vcc2
10K
15K
MUTE
10K

- Spindle Actuator
+ +
-

Driver(4X) Driver(6x)
-

25K

+
Thermal
Shut down
Vcc2
Vcc2
Vcc1
25K 10K
+

-
+
-

25K Sled Actuator

+
-

Driver(4X) Driver(6x)
Pre-DRV TRAY
Vcc1
DRIVER
PGND
10K

1 2 3 4 5 6 7 8 9 10 11 12 13 14
10K

10K

V1 V4
V6 V7 V8 45 20 10
REGOUT
ADJ 2.5V

16.4K
47uF

10K
5V

REGOUT
ADJ 3.3V

47uF

AMtek SEMICONDUCTORS -8- Nov 2004 V1.1

 AM5888S
Motor Driver ICs

Packaging outline

HSOP28
D

28 15

E E1

1 14

B
e
b1

A2 A

0.089 C

C A1

SYMBOL MILLIMETERS INCHES

Min. Max. Min. Max.
A - 2.75 - 0.108
A1 - 0.3 - 0.012
A2 - 2.45 - 0.096
B 4.95 5.35 0.195 0.211
b1 0.23 0.47 0.009 0.019
C 0.2 0.36 0.008 0.014
D 17.89 18.8 0.704 0.740
E 7.3 7.9 0.287 0.311
E1 9.6 10.65 0.378 0.419
e 0.8 (TYP) 0.031(TYP)
L 0.3 - 0.012 -

AMtek SEMICONDUCTORS -9- Nov 2004 V1.1

 AM5888S
Motor Driver ICs

Marking Identification

AMtek Row I

Row II

Row III

Row I
AMtek

Row II
Part number (Pb)
(Pb free)
Part number L/F

Row III
Lot number

AMtek SEMICONDUCTORS - 10 - Nov 2004 V1.1