Spring Cat

Spring Products
Wherever motion takes place in dies, molds or machin-

TABLE OF CONTENTS ery, some type of springs will be found.
DIE SPRINGS At Lamina, we have long believed that Raymond Die

Introduction 2 Springs give the best value. Made from chrome silicon
Selecting Die Springs 3 alloys, Raymond Die Springs have long cycle lives in most
Die Springs Dos and Donts 3 applications. They are readily available from stock and
Medium-Duty-Inch 4-5 are reasonably priced.
Medium Heavy-Duty-Inch 6-7
Heavy-Duty-Inch 8-9
Extra Heavy-Duty-Inch 10-11 Mechanical die springs have long been the first choice for
Standard Tolerance for Free Lengths 11 pressure control applications involving metal stamping
Raymond-Lamina ISO Die Spring Metric 12 dies. Die springs are widely used in general tooling, such
Light Duty-ISO Metric 12-13 as jigs and fixtures as well as components in the automo-
Medium Duty-ISO Metric 14-15 tive, appliance, canning, electronic, and farm implement
Heavy Duty-ISO Metric 16-17 industries. We also see them used in plastics injection
Extra Heavy Duty-ISO Metric 18-19 molds.
Spring Cages 20
Also, from Associated Spring Raymond is a wide selection
UTILITY SPRINGS of compression and extension springs. Quality and reli-
Round Wire Die & Fixture Springs Utility 21
ability are important features in any product manufactured
Compression Steel Fixture Springs Utility 22-23
Extension Steel Fixture Springs Utility 23-24 and/or distributed by Lamina Components. We are proud
General Maintenance Assortment 25 to offer these utility springs which complement our line of
Midget, Compression, Extension Spring Assortment 26 pressure control devices.
Square Wire Carbon Steel Die & Fixture Springs 27
Glossary of Spring Terminology 28 Urethane springs may be used for stripping metal from
punches, tooling in press brakes, as die springs and
LAMI-FLEX SPRINGS assorted other applications such as pressure pads and
General Information 29-30 forming.
Light Duty Lami-Flex Springs 31-32
Medium Duty Lami-Flex Springs 32-33 Lamina offers urethane in 90A and 95A durometers in stan-
Heavy Duty Lami-Flex Springs 34-35
dard tubes, rods, sheets and slabs. Special sizes and
Extra Heavy Duty Lami-Flex Springs 35
Solid Rods 36 durometers are available.
Solid Bars 36
Solid Sheets and Slabs 37 Schnorr Disc Springs are also important to the Lamina
Components line of pressure control devices. Where a
DISC SPRINGS high degree of accuracy and short travel are required,
General Information 38-39 disc springs offer the most predictable deflection rates of
Typical Disc Spring Application 40 all pressure control devices.
Disc Springs 41-47
Anchor Lamina Mission
To be the customer focused world class supplier of choice

to the metal working and plastics industry.
We will help our customers to compete globally by provid-

ing innovative and value added products and services.
Please check our website

www.anchorlamina.com for the
lastest technical information.
2
SELECTING DIE SPRINGS
DIE SPRINGS
Springs for strippers, pressure pads and tion is to always use as many springs as
other die components can be selected the die will accommodate that will produce PRELOAD
from the ratings (pounds per 1/10 deflec- the required load with the least amount of
tion and at maximum deflection) given in deflection. This will increase the useful
OPERATION
the charts on pages 4 to 19. life of the spring, reduce the chances of TRAVEL
spring failure and the resulting downtime,
The first decision to be made is the type loss of production and increased mainte-
of duty the springs will be called on to nance cost.
FREE
perform: Short run, normal, long run, high LENGTH
speed, or extra stress and use the appro- The more rapidly a spring works, the more
priate chart (pages 4 to 19). attention must be paid to its fatigue limits.
COMPRESSED
In slow moving dies or fixtures, it is pos- LENGTH
Another approach to spring selection is to sible to get good performance with springs
work back from the amount of operating operating near maximum deflection. As
travel the springs will be subjected to as the working speed increases, the life ex-
indicated on the die layout. Select springs pectancy of the spring at that deflection
in the correct duty range which will oper- decreases.
ate efficiently at the indicated travel. Cal- ROD
DIA.
culate the number of springs needed by Die spring costs are very small part of the HOLE
working with the pressure pounds for a total cost of the die. An effort to save a DIA
single spring indicated on the chart. few cents on die springs is a misguided
act that can cost many dollars in lost time
A general rule to observe in spring selec- and labor.
CORRECT DIE SPRING USAGE

DO... perform preventive maintenance on in the vibration frequency and results in
die on a regularly scheduled basis. spring failure. INCORRECT DIE SPRING
Records should be kept on the number of USAGE
cycles performed by the die. Die Springs DO... provide spring safeguards from ad-
should be replaced at predetermined in- verse external elements such as heat, DONT... wait until the die is built to deter-
tervals to prevent expensive downtime. corrosive atmosphere, metal chips and mine which springs and how many are
other obstructions. needed for the job. Make spring selec-
DO... provide proper guidance on all tion a part of the design function and work
springs to reduce buckling. All springs are DO... deepen the spring pockets propor- within the springs practical limits.
designed to work within standard hole tionately when the die is sharpened in
sizes and over standard rod sizes. Care order to maintain the same spring travel DONT... expect the maximum perfor-
should always be exercised in mounting and load level. mance life from a spring that is producing
springs. the maximum load.
DO... consult your Lamina Die Spring dis-
DO... preload each spring in the as- tributor or directly with Lamina Customer DONT... replace only one spring in a die.
sembled tool to prevent the possibility of Service on Die Spring problems you may
Replace all of the springs to redistribute
shock loading which causes a stress surge encounter.
the loads evenly over each spring instead
of over an unbalanced assembly of some
new and some old springs. The small
CORRECT extra investment will pay handsome divi-
STRIPPER COUNTERBORED OPEN PIN dends.
BOLT HOLES HOLES
DONT... mix springs of assorted lengths
or springs with different deflection ranges
on the same die section.
DONT... alter a die spring by cutting off

INCORRECT
coils or grinding the inside or outside di-
DRILLED HOLES STUDS ameters. These practices cause early
GREATER THAN
spring failure and potential die damage.

SPRING DIA.
3
MEDIUM-DUTY DIE SPRINGS - INCH
MAXIMUM DEFLECTION 50%
CK
STO ROD HOLE
IN
FREE
INCHES X 25.4 = MM LENGTH
LBS. X .454 = KG
MEDIUM DUTY DIE SPRINGS INCH BLUE
Deflection for Deflection for
Free Length Pounds Long Life Average Life
*Maximum Deflection
Hole Rod PART at 50% of Free Length No.
25% of Free Length 40% of Free Length Per
Dia. Dia. NUMBER 1/10" Box
Deflection Pressure Length of Pressure Length of Pressure Length of
Inch mm Pounds Deflection Pounds Deflection Pounds Deflection
1.00 25 M-100 6.00 15.00 0.25 24.00 0.40 30.00 0.50 200
1.25 32 M-100A 5.40 16.90 0.31 27.00 0.50 33.80 0.63 200
3/8 3/16 1.50 38 M-101 4.00 15.00 0.38 24.00 0.60 30.00 0.75 100
10mm 4.5mm 1.75 44 M-101A 3.40 14.90 0.44 23.80 0.70 29.80 0.88 100
2.00 51 M-102 2.80 14.00 0.50 22.40 0.80 28.00 1.00 100
Wire 2.50 64 M-103 2.40 15.00 0.63 24.00 1.00 30.00 1.25 100
.039 x
.070 3.00 76 M-104 2.10 15.80 0.75 25.20 1.20 31.50 1.50 100
12.00 305 M-105 0.60 18.00 3.00 28.80 4.80 36.00 6.00 50
1.00 25 M-110 11.00 27.50 0.25 44.00 0.40 55.00 0.50 100
1.25 32 M-110A 8.20 25.60 0.31 41.00 0.50 51.30 0.63 100
1.50 38 M-111 6.80 25.50 0.38 40.80 0.60 51.00 0.75 100
1.75 44 M-111A 6.00 26.30 0.44 42.00 0.70 52.50 0.88 100
2.00 51 M-112 5.50 27.50 0.50 44.00 0.80 55.00 1.00 100
2.50 64 M-113 4.50 28.10 0.63 45.00 1.00 56.30 1.25 50
1/2 9/32 3.00 76 M-114 3.50 26.30 0.75 42.00 1.20 52.50 1.50 50
13mm 7mm
3.50 89 M-115 3.00 26.30 0.88 42.00 1.40 52.50 1.75 50
Wire 4.50 114 M-115A 2.50 28.10 1.13 45.00 1.80 56.30 2.25 50
.052 x 5.50 140 M-115B 2.10 28.90 1.38 46.20 2.20 57.80 2.75 50
.093 6.50 165 M-115C 1.40 22.80 1.63 36.40 2.60 45.50 3.25 50
7.50 191 M-115D 1.20 22.50 1.88 36.00 3.00 45.00 3.75 50
12.00 305 M-116 0.70 21.00 3.00 33.60 4.80 42.00 6.00 50
1.00 25 M-120 16.40 41.00 0.25 65.60 0.40 82.00 0.50 100
1.25 32 M-120A 12.80 40.00 1.31 64.00 0.50 80.00 0.63 100
1.50 38 M-121 10.80 40.50 0.38 64.80 0.60 81.00 0.75 50
1.75 44 M-121A 9.60 42.00 0.44 67.20 0.70 84.00 0.88 50
5/8 11/32 2.00 51 M-122 8.80 44.00 0.50 70.40 0.80 88.00 1.00 50
16mm 8.5mm 2.50 64 M-123 6.00 37.50 0.63 60.00 1.00 75.00 1.25 50
3.00 76 M-124 5.60 42.00 0.75 67.20 1.20 84.00 1.50 50
Wire
.069 x 3.50 89 M-125 4.80 42.00 0.88 67.20 1.40 84.00 1.75 50
.109 4.00 102 M-126 4.40 44.00 1.00 70.40 1.60 88.00 2.00 50
12.00 305 M-127 1.60 48.00 3.00 76.80 4.80 96.00 6.00 50
1.00 25 M-1 31.20 78.00 0.25 124.80 0.40 156.00 0.50 50
1.25 32 M-1A 25.60 80.00 0.31 128.00 0.50 160.00 0.63 50
1.50 38 M-2 20.00 75.00 0.38 120.00 0.60 150.00 0.75 50
1.75 44 M-2A 17.60 77.00 0.44 123.20 0.70 154.00 0.88 50
2.00 51 M-3 14.40 72.00 0.50 115.20 0.80 144.00 1.00 50
2.50 64 M-4 12.00 75.00 0.63 120.00 1.00 150.00 1.25 50
3.00 76 M-5 9.60 72.00 0.75 115.20 1.20 144.00 1.50 50
3/4 3/8 3.50 89 M-6 8.00 70.00 0.88 112.00 1.40 140.00 1.75 50
19mm 9.5mm 4.00 102 M-7 7.20 72.00 1.00 115.20 1.60 144.00 2.00 50
4.50 114 M-8 6.40 72.00 1.13 115.20 1.80 144.00 2.25 50
Wire
.075 x 5.00 127 M-9 6.00 75.00 1.25 120.00 2.00 150.00 2.50 50
.165 5.50 140 M-10 5.50 75.60 1.38 121.00 2.20 151.30 2.75 50
6.00 152 M-11 5.00 75.00 1.50 120.00 2.40 150.00 3.00 50
6.50 165 M-11B 4.50 73.10 1.63 117.00 2.60 146.30 3.25 50
7.50 191 M-11C 3.80 71.30 1.88 114.00 3.00 142.50 3.75 50
12.00 305 M-11A 2.40 72.00 3.00 115.20 4.80 144.00 6.00 50
*Deflection values shown represent compressed lengths near solid and are for design See page 3 for Die Springs
information only. The color blue is a registered trademark of Barnes Group Inc. Dos and Donts.
4
MEDIUM DUTY DIE SPRINGS INCH BLUE
Deflection for Deflection for *Maximum Deflection
Free Length Pounds at Long Life Average Life No.
Hole Rod PART 25% of Free Length 40% of Free Length 50% of Free Length
Dia. Dia. NUMBER 1/10" Per
Deflection Pressure Length of Pressure Length of Pressure Length of Box
Inch mm Pounds Deflection Pounds Deflection Pounds Deflection
1.00 25 M-12 55.00 137.50 0.25 220.00 0.40 275.00 0.50 50
1.25 32 M-12A 45.00 140.60 0.31 225.00 0.50 281.30 0.63 50
1.50 38 M-13 35.00 131.30 0.38 210.00 0.60 262.50 0.75 50
1.75 44 M-13A 30.00 131.30 0.44 210.00 0.70 262.50 0.88 50
2.00 51 M-14 26.00 130.00 0.50 208.00 0.80 260.00 1.00 50
2.50 64 M-15 20.00 125.00 0.63 200.00 1.00 250.00 1.25 50
3.00 76 M-16 16.50 123.80 0.75 198.00 1.20 247.50 1.50 25
3.50 89 M-17 15.00 131.80 0.88 210.00 1.40 262.50 1.75 25
1 1/2 4.00 102 M-18 12.00 120.00 1.00 192.00 1.60 240.00 2.00 25
26mm 12.5mm 4.50 114 M-19 10.40 117.00 1.13 187.60 1.80 234.00 2.25 25
5.00 127 M-20 9.60 120.00 1.25 192.00 2.00 240.00 2.50 25
Wire
.100 x 5.50 140 M-21 8.80 121.00 1.38 193.60 2.20 242.00 2.75 25
.215 6.00 152 M-22 8.00 120.00 1.50 192.00 2.40 240.00 3.00 25
7.00 178 M-23 7.20 126.00 1.75 201.60 2.80 252.00 3.50 25
8.00 203 M-24 6.00 120.00 2.00 192.00 3.20 240.00 4.00 25
12.00 305 M-24A 4.00 120.00 3.00 192.00 4.80 240.00 6.00 25
1.50 38 M-36 49.60 186.00 0.38 297.60 0.60 372.00 0.75 50
1.75 44 M-36A 42.40 185.50 0.44 296.80 0.70 371.00 0.88 50
2.00 51 M-37 35.20 176.00 0.50 281.60 0.80 352.00 1.00 50
2.50 64 M-38 28.80 180.00 0.63 288.00 1.00 360.00 1.25 25
3.00 76 M-39 24.00 180.00 0.75 288.00 1.20 360.00 1.50 25
3.50 89 M-40 20.00 175.00 0.88 280.00 1.40 350.00 1.75 25
4.00 102 M-41 17.60 176.00 1.00 281.60 1.60 352.00 2.00 25
1-1/4 5/8 M-42
4.50 114 16.00 180.00 1.13 288.00 1.80 360.00 2.25 25
32mm 15.5mm
5.00 127 M-43 13.60 170.00 1.25 272.00 2.00 340.00 2.50 25
Wire 5.50 140 M-44 12.80 176.00 1.38 281.60 2.20 352.00 2.75 25
.155 x 6.00 152 M-45 12.00 180.00 1.50 288.00 2.40 360.00 3.00 25
.285 7.00 178 M-46 10.40 182.00 1.75 291.20 2.80 364.00 3.50 25
8.00 203 M-47 8.80 176.00 2.00 281.60 3.20 352.00 4.00 25
10.00 254 M-48 7.20 180.00 2.50 288.00 4.00 360.00 5.00 25
12.00 305 M-48A 6.00 180.00 3.00 288.00 4.80 360.00 6.00 25
2.00 51 M-49 53.00 265.00 0.50 424.00 0.80 530.00 1.00 25
2.50 64 M-50 45.00 281.30 0.63 450.00 1.00 562.50 1.25 25
3.00 76 M-51 36.00 270.00 0.75 432.00 1.20 540.00 1.50 25
3.50 89 M-52 30.00 262.50 0.88 420.00 1.40 525.00 1.75 25
4.00 102 M-53 27.00 270.00 1.00 432.00 1.60 540.00 2.00 25
4.50 114 M-54 23.00 258.80 1.13 414.00 1.80 517.50 2.25 25
1-1/2 3/4 M-55
5.00 127 21.00 262.50 1.25 420.00 2.00 525.00 2.50 25
38mm 19mm
5.50 140 M-55A 18.50 254.40 1.38 407.00 2.20 508.80 2.75 25
Wire 6.00 152 M-56 17.00 255.00 1.50 408.00 2.40 510.00 3.00 25
.135 x 7.00 178 M-56A 14.50 253.80 1.75 406.00 2.80 507.00 3.50 25
.345 8.00 203 M-57 12.80 256.00 2.00 409.60 3.20 512.00 4.00 25
10.00 254 M-58 10.00 250.00 2.50 400.00 4.00 500.00 5.00 25
12.00 305 M-58A 8.00 240.00 3.00 384.00 4.80 480.00 6.00 25
2.50 64 M-70 100.00 625.00 0.63 1000.00 1.00 1250.00 1.25 25
3.00 76 M-71 83.00 622.50 0.75 996.00 1.20 1245.00 1.50 25
3.50 89 M-72 64.80 567.00 0.88 907.20 1.40 1134.00 1.75 25
4.00 102 M-73 60.00 600.00 1.00 960.00 1.60 1200.00 2.00 25
4.50 114 M-74 53.00 596.30 1.13 954.00 1.80 1192.00 2.25 25
2 1 5.00 127 M-75 47.00 587.50 1.25 940.00 2.00 1175.00 2.50 25
51mm 25mm 5.50 140 M-76 39.20 539.00 1.38 862.40 2.20 1178.00 2.75 25
6.00 152 M-77 39.00 585.00 1.50 936.00 2.40 1170.00 3.00 25
Wire 7.00 178 M-79 31.20 546.00 1.75 873.60 2.80 1092.00 3.50 25
.195 x
.468 8.00 203 M-80 28.50 570.00 2.00 912.00 3.20 1140.00 4.00 10
10.00 254 M-82 20.80 520.00 2.50 832.00 4.00 1040.00 5.00 10
12.00 305 M-83 17.50 525.00 3.00 840.00 4.80 1050.00 6.00 10
*Deflection values shown represent compressed lengths near solid and are for design Let us quote your specials!
information only. The color blue is a registered trademark of Barnes Group Inc.
5
MEDIUM-HEAVY DUTY DIE SPRINGS - INCH
K
OC ROD HOLE
ST
IN
FREE
LBS. X .454 = KG
MEDIUM HEAVY-DUTY DIE SPRINGS INCH RED
Pounds Deflection for Deflection for
*Maximum Deflection No.
Hole Rod Free Length Part at Optimum LIfe Long Life
30% of Free Length
1 20% of Free Length 25% of Free Length per
Dia. Dia. Number /10"
Box
Inch mm Deflection Load (lb) Deflection (in) Load (lb) Deflection (in) Load (lb) Deflection (in)
1.00 25 MHC-100 9.00 18.00 0.20 22.50 0.25 33.30 0.37 200
1.25 32 MHC-100A 7.30 18.30 0.25 22.80 0.31 33.80 0.46 200
3/8 3/16 1.50 38 MHC-101 6.70 20.10 0.30 25.10 0.38 37.20 0.56 100
10mm 4.5mm 1.75 44 MHC-101A 5.80 20.30 0.35 25.40 0.44 37.60 0.65 100
2.00 51 MHC-102 5.00 20.00 0.40 25.00 0.50 37.00 0.74 100
WIRE 2.50 64 MHC-103 4.20 21.00 0.50 26.30 0.63 38.90 0.93 100
.046 x 3.00 76 MHC-104 3.00 18.00 0.60 22.50 0.75 33.30 1.11 100
.067 12.00 305 MHC-106 0.90 21.60 2.40 27.00 3.00 40.00 4.44 50
1.00 25 MHC-110 16.80 33.60 0.20 42.00 0.25 62.20 0.37 100
1.25 32 MHC-110A 13.00 32.50 0.25 40.60 0.31 60.10 0.46 100
1/2 9/32 1.50 38 MHC-111 9.50 28.50 0.30 35.60 0.38 52.70 0.56 100
13mm 7mm 1.75 44 MHC-111A 8.50 29.80 0.35 37.20 0.44 55.00 0.65 100
2.00 51 MHC-112 7.50 30.00 0.40 37.50 0.50 55.50 0.74 100
WIRE 2.50 64 MHC-113 6.00 30.00 0.50 37.50 0.63 55.50 0.93 50
.061 x 3.00 76 MHC-114 5.70 34.20 0.60 42.80 0.75 63.30 1.11 50
.156 3.50 89 MHC-115 4.00 28.00 0.70 35.00 0.88 51.80 1.30 50
12.00 305 MHC-117 1.20 28.80 2.40 36.00 3.00 53..30 4.44 50
1.00 25 MHC-120 30.00 60.00 0.20 75.00 0.25 111.00 0.37 100
1.25 32 MHC-120A 21.50 53.80 0.25 67.20 0.31 99.40 0.46 100
1.50 38 MHC-121 19.00 57.00 0.30 71.30 0.38 105.50 0.56 50
5/8 11/32 1.75 44 MHC-121A 16.80 58.80 0.35 73.50 0.44 108.80 0.65 50
16mm 8.5mm 2.00 51 MHC-122 14.80 59.20 0.40 74.00 0.50 109.50 0.74 50
2.50 64 MHC-123 11.50 57.50 0.50 71.90 0.63 106.40 0.93 50
WIRE 3.00 76 MHC-124 10.00 60.00 0.60 75.00 0.75 111.00 1.11 50
.081 x 3.50 89 MHC-125 8.50 59.50 0.70 74.40 0.88 110.10 1.30 50
.117 4.00 102 MHC-126 7.60 60.80 0.80 76.00 1.00 112.50 1.48 50
12.00 305 MHC-127 2.70 64.80 2.40 81.00 3.00 119.90 4.44 50
1.00 25 MHC-1 50.00 100.00 0.20 125.00 0.25 185.00 0.37 50
1.25 32 MHC-1A 38.00 95.00 0.25 118.80 0.31 175.80 0.46 50
1.50 38 MHC-2 32.00 96.00 0.30 120.00 0.38 177.60 0.56 50
1.75 44 MHC-2A 28.00 100.80 0.35 126.00 0.44 186.50 0.65 50
2.00 51 MHC-3 24.80 99.20 0.40 124.00 0.50 183.50 0.74 50
2.50 64 MHC-4 19.20 96.00 0.50 120.00 0.63 177.60 0.93 50
3/4 3/8
3.00 76 MHC-5 14.40 86.40 0.60 108.00 0.75 159.00 1.11 50
19mm 9.5mm
3.50 89 MHC-6 12.80 89.60 0.70 112.00 0.88 165.80 1.30 50
4.00 102 MHC-7 12.00 96.00 0.80 120.00 1.00 177.60 1.48 50
4.50 114 MHC-8 11.20 100.80 0.90 126.00 1.13 186.50 1.67 50
WIRE
5.00 127 MHC-9 9.00 90.00 1.00 112.50 1.25 166.50 1.85 50
.093 x
5.50 140 MHC-10 8.00 88.00 1.10 110.00 1.38 162.80 2.04 50
.156
6.00 152 MHC-11 7.50 90.00 1.20 112.50 1.50 166.50 2.22 50
12.00 305 MHC-11A 3.60 86.40 2.40 108.00 3.00 159.80 4.44 50
information only. The color red is a registered trademark of Barnes Group Inc.
Dos and Donts.
6
MEDIUM HEAVY-DUTY DIE SPRINGS INCH RED
Pounds Deflection for Deflection for No.
Hole Rod Free Length Part at Optimum LIfe Long Life *Maximum Deflection
1
/10" 30% of Free Length per
Dia. Dia. Number 20% of Free Length 25% of Free Length Box
Deflection
Inch mm Load (lb) Deflection (in) Load (lb) Deflection (in) Load (lb) Deflection (in)
1.00 25 MHC-12 76.00 152.00 0.20 190.00 0.25 281.20 0.37 50
1.25 32 MHC-12A 62.40 156.00 0.25 195.00 0.31 288.60 0.46 50
1.50 38 MHC-13 49.60 148.80 0.30 186.50 0.38 275.30 0.56 50
1.75 44 MHC-13A 44.00 154.00 0.35 192.50 0.44 284.90 0.65 50
2.00 51 MHC-14 40.00 160.00 0.40 200.00 0.50 296.00 0.74 50
2.50 64 MHC-15 31.00 155.00 0.50 193.80 0.63 286.80 0.93 50
3.00 76 MHC-16 25.00 150.00 0.60 187.50 0.75 277.50 1.11 25
1 1/2 3.50 89 MHC-17 21.60 151.20 0.70 189.00 0.88 279.70 1.30 25
26mm 12.5mm 4.00 102 MHC-18 18.40 147.20 0.80 184.00 1.00 272.30 1.48 25
4.50 114 MHC-19 17.00 153.00 0.90 191.30 1.13 283.10 1.67 25
WIRE 5.00 127 MHC-20 14.40 144.00 1.00 180.00 1.25 266.40 1.85 25
.115 x 5.50 140 MHC-21 12.80 140.80 1.10 176.00 1.38 260.50 2.04 25
.218 6.00 152 MHC-22 12.00 144.00 1.20 180.00 1.50 266.40 2.22 25
7.00 178 MHC-23 10.00 140.00 1.40 175.00 1.75 259.00 2.59 25
8.00 203 MHC-24 8.80 140.80 1.60 176.00 2.00 260.50 2.96 25
12.00 305 MHC-24A 6.20 148.80 2.40 186.00 3.00 275.30 4.44 25
1.50 38 MHC-36 114.40 343.20 0.30 429.00 0.38 634.90 0.56 50
1.75 44 MHC-36A 100.80 352.80 0.35 441.00 0.44 652.70 0.65 50
2.00 51 MHC-37 86.40 345.60 0.40 432.00 0.50 639.40 0.74 50
2.50 64 MHC-38 62.40 312.00 0.50 390.00 0.63 577.20 0.93 25
3.00 76 MHC-39 51.20 307.20 0.60 384.00 0.75 568.30 1.11 25
1-1/4 5/8
3.50 89 MHC-40 44.00 308.00 0.70 385.00 0.88 569.80 1.30 25
32mm 15.5mm
4.00 102 MHC-41 36.80 294.40 0.80 368.00 1.00 544.60 1.48 25
4.50 114 MHC-42 32.00 288.00 0.90 360.00 1.13 532.80 1.67 25
WIRE
5.00 127 MHC-43 29.00 290.00 1.00 362.50 1.25 536.50 1.85 25
.156 x
5.50 140 MHC-44 26.40 290.40 1.10 363.00 1.38 537.20 2.04 25
.281
6.00 152 MHC-45 25.00 300.00 1.20 375.00 1.50 555.00 2.22 25
7.00 178 MHC-46 20.00 280.00 1.40 350.00 1.75 518.00 2.59 25
8.00 203 MHC-47 18.40 294.40 1.60 368.00 2.00 544.60 2.96 25
10.00 254 MHC-48 14.50 290.00 2.00 362.50 2.50 536.50 3.70 25
12.00 305 MHC-48A 12.40 297.60 2.40 372.00 3.00 550.60 4.44 25
2.00 51 MHC-49 108.00 432.00 0.40 540.00 0.50 799.20 0.74 25
2.50 64 MHC-50 85.60 428.00 0.50 535.00 0.63 791.80 0.93 25
3.00 76 MHC-51 62.40 374.40 0.60 468.00 0.75 692.60 1.11 25
3.50 89 MHC-52 52.80 369.60 0.70 462.00 0.88 683.80 1.30 25
4.00 102 MHC-53 48.00 384.00 0.80 480.00 1.00 710.40 1.48 25
4.50 114 MHC-54 43.20 388.80 0.90 486.00 1.13 719.30 1.67 25
1-1/2 3/4
5.00 127 MHC-55 36.80 368.00 1.00 460.00 1.25 680.80 1.85 25
38mm 19mm
5.50 140 MHC-55A 34.40 378.40 1.10 473.00 1.38 700.00 2.04 25
6.00 152 MHC-56 30.40 364.80 1.20 456.00 1.50 674.90 2.22 25
WIRE
7.00 178 MHC-56A 26.40 369.60 1.40 462.00 1.75 683.80 2.59 25
.187 x
8.00 203 MHC-57 22.00 352.00 1.60 440.00 2.00 651.20 2.96 25
.312
10.00 254 MHC-58 17.60 352.00 2.00 440.00 2.50 651.20 3.70 25
12.00 305 MHC-58A 14.40 345.60 2.40 432.00 3.00 639.40 4.44 25
2.50 64 MHC-70 118.40 592.00 0.50 740.00 0.63 1095.20 0.93 25
3.00 76 MHC-71 96.00 576.00 0.60 720.00 0.75 1065.60 1.11 25
3.50 89 MHC-72 80.00 560.00 0.70 700.00 0.88 1036.00 1.30 25
4.00 102 MHC-73 66.40 531.20 0.80 664.00 1.00 982.70 1.48 25
2 1 4.50 114 MHC-74 60.00 540.00 0.90 674.00 1.13 999.00 1.67 25
51mm 25mm 5.00 127 MHC-75 56.00 560.00 1.00 700.00 1.25 1036.00 1.85 25
5.50 140 MHC-76 50.40 554.00 1.10 693.00 1.38 1025.60 2.04 25
WIRE 6.00 152 MHC-77 47.20 566.40 1.20 708.00 1.50 1047.80 2.22 25
.225 x 7.00 178 MHC-79 40.00 560.00 1.40 700.00 1.75 1036.00 2.59 25
.437 8.00 203 MHC-80 35.20 563.20 1.60 704.00 2.00 1041.90 2.96 10
10.00 254 MHC-82 26.00 520.00 2.00 650.00 2.50 962.00 3.70 10
12.00 305 MHC-83 22.40 537.60 2.40 672.00 3.00 994.60 4.44 10
information only. The color red is a registered trademark of Barnes Group Inc.
7
HEAVY DUTY DIE SPRINGS - INCH
K ROD HOLE
OC
ST
IN FREE
LBS. X .454 = KG
HEAVY-DUTY DIE SPRINGS INCH GOLD
Pounds Deflection for Deflection for
30% of Free Length
1 15% of Free Length 20% of Free Length per
Dia. Dia. Number /10"
Box
Inch mm Deflection Load (lb) Deflection (in) Load (lb) Deflection (in) Load (lb) Deflection (in)
1.00 25 H-100 11.00 16.50 0.15 22.00 0.20 33.00 0.30 200
1.25 32 H-100A 9.80 18.40 0.19 24.50 0.25 36.80 0.38 200
3/8 3/16 1.50 38 H-101 8.00 18.00 0.23 24.00 0.30 36.00 0.45 100
10mm 4.5mm 1.75 44 H-101A 8.40 22.10 0.26 29.40 0.35 44.10 0.53 100
WIRE 2.00 51 H-102 7.20 21.60 0.30 28.80 0.40 43.20 0.60 100
.054 x 2.50 64 H-103 5.50 20.60 0.38 27.50 0.50 41.30 0.75 100
.072 3.00 76 H-104 4.20 18.90 0.45 25.20 0.60 37.80 0.90 100
12.00 305 H-105 1.20 21.60 1.80 28.80 2.40 43.20 3.60 50
1.00 25 H-110 23.60 35.40 0.15 47.20 0.20 70.80 0.30 100
1.25 32 H-110A 18.60 34.90 0.19 46.50 0.25 69.80 0.38 100
1/2 1.50 38 H-111 15.50 34.90 0.23 46.50 0.30 69.80 0.45 100
13mm 1.75 44 H-111A 13.80 36.20 0.26 48.30 0.35 72.50 0.53 100
9/32
WIRE 7mm 2.00 51 H-112 11.00 33.00 0.30 44.00 0.40 66.00 0.60 100
.070 x 2.50 64 H-113 8.40 31.50 0.38 42.00 0.50 63.00 0.75 50
093 3.00 76 H-114 7.40 33.30 0.45 44.40 0.60 66.60 0.90 50
3.50 89 H-115 6.00 31.50 0.53 42.00 0.70 63.00 1.05 50
12.00 305 H-117 1.60 28.80 1.80 38.40 2.40 57.60 3.60 50
1.00 25 H-120 42.40 63.60 0.15 84.80 0.20 127.20 0.30 100
1.25 32 H-120A 29.60 55.50 0.19 74.00 0.25 111.00 0.38 100
1.50 38 H-121 27.20 61.20 0.23 81.60 0.30 122.40 0.45 50
1.75 44 H-121A 24.00 63.00 0.26 84.00 0.35 126.00 0.53 50
5/8 11/32 2.00 51 H-122 20.80 62.40 0.30 83.20 0.40 124.80 0.60 50
16mm 8.5mm
2.50 64 H-123 17.00 63.80 0.38 85.00 0.50 127.50 0.75 50
WIRE 3.00 76 H-124 14.40 64.80 0.45 86.40 0.60 129.60 0.90 50
.093 x 3.50 89 H-125 12.20 64.10 0.53 85.40 0.70 128.10 1.05 50
.125 4.00 102 H-126 10.80 64.80 0.60 86.40 0.80 129.60 1.20 50
12.00 305 H-127 3.00 54.00 1.80 72.00 2.40 108.00 3.60 50
1.00 25 H-1 108.00 162.00 0.15 216.00 0.20 324.00 0.30 50
1.25 32 H-1A 88.00 165.00 0.19 220.00 0.25 330.00 0.38 50
1.50 38 H-2 65.50 147.60 0.23 196.80 0.30 295.20 0.45 50
1.75 44 H-2A 60.00 157.50 0.26 210.00 0.35 315.00 0.53 50
2.00 51 H-3 49.60 148.80 0.30 198.40 0.40 297.60 0.60 50
2.50 64 H-4 40.00 150.00 0.38 200.00 0.50 300.00 0.75 50
3/4 3/8 3.00 76 H-5 34.00 153.00 0.45 204.00 0.60 306.00 0.90 50
19mm 9.5mm 3.50 89 H-6 28.00 147.00 0.53 196.00 0.70 294.00 1.05 50
4.00 102 H-7 25.00 150.00 0.60 200.00 0.80 300.00 1.20 50
WIRE
.125 x 4.50 114 H-8 22.00 148.50 0.68 198.00 0.90 297.00 1.35 50
.165 5.00 127 H-9 19.50 146.30 0.75 195.00 1.00 292.50 1.50 50
5.50 140 H-10 17.00 140.30 0.83 187.00 1.10 280.50 1.65 50
6.00 152 H-11 16.00 144.00 0.90 192.00 1.20 288.00 1.80 50
12.00 305 H-11A 8.00 144.00 1.80 192.00 2.40 288.00 3.60 50
information only. The color gold is a registered trademark of Barnes Group Inc.
Dos and Donts.
8
HEAVY-DUTY DIE SPRINGS INCH GOLD
Pounds *Maximum Deflection No.
30% of Free Length
15% of Free Length 20% of Free Length per
Dia. Dia. Number 1
/10"
Box
Deflection
1.00 25 H-12 208.00 312.00 0.15 416.00 0.20 624.00 0.30 50

1.25 32 H-12A 171.20 321.00 0.19 428.00 0.25 642.00 0.38 50
1.50 38 H-13 118.40 266.40 0.23 355.20 0.30 532.00 0.45 50
1.75 44 H-13A 104.00 273.00 0.26 364.00 0.35 546.00 0.53 50
2.00 51 H-14 90.00 270.00 0.30 360.00 0.40 540.00 0.60 50
2.50 64 H-15 68.00 255.00 0.38 340.00 0.50 510.00 0.75 50
3.00 76 H-16 54.40 244.80 0.45 326.40 0.60 489.60 0.90 25
1 1/2 3.50 89 H-17 45.60 239.40 0.53 319.20 0.70 478.80 1.05 25
26mm 12.5mm 4.00 102 H-18 40.00 240.00 0.60 320.00 0.80 480.00 1.20 25
4.50 114 H-19 35.20 237.60 0.68 316.80 0.90 475.20 1.35 25
WIIRE 5.00 127 H-20 31.20 234.00 0.75 312.00 1.00 468.00 1.50 25
.158 x
.225 5.50 140 H-20A 28.80 237.60 0.83 316.80 1.10 475.20 1.65 25
6.00 152 H-21 25.60 230.40 0.90 307.20 1.20 460.80 1.80 25
7.00 178 H-21A 22.40 235.20 1.05 313.60 1.40 470.40 2.10 25
8.00 203 H-22 19.20 230.40 1.20 307.20 1.60 460.80 2.40 25
12.00 305 H-22A 12.00 216.00 1.80 288.00 2.40 432.00 3.60 25
1.50 38 H-36 212.00 477.00 0.23 636.00 0.30 954.00 0.45 50
1.75 44 H-36A 181.60 476.70 0.26 635.60 0.35 953.40 0.53 50
2.00 51 H-37 149.60 448.80 0.30 598.40 0.40 897.60 0.60 50
2.50 64 H-38 117.60 441.00 0.38 588.00 0.50 882.00 0.75 25
3.00 76 H-39 95.20 428.40 0.45 571.20 0.60 856.80 0.90 25
3.50 89 H-40 75.20 394.80 0.53 526.40 0.70 789.60 1.05 25
4.00 102 H-41 66.40 398.40 0.60 531.20 0.80 796.80 1.20 25
1-1/4 5/8
4.50 114 H-42 58.40 394.20 0.68 525.60 0.90 788.40 1.35 25
32mm 15.5mm 5.00 127 H-43 53.00 397.50 0.75 530.00 1.00 795.00 1.50 25
WIRE 5.50 140 H-44 47.20 389.40 0.83 519.20 1.10 778.80 1.65 25
.200 x 6.00 152 H-45 42.40 381.60 0.90 508.80 1.20 763.20 1.80 25
.295 7.00 178 H-46 36.80 386.40 1.05 515.20 1.40 772.80 2.10 25
8.00 203 H-47 32.80 393.60 1.20 524.80 1.60 787.20 2.40 25
10.00 254 H-48 25.60 384.00 1.50 512.00 2.00 768.00 3.00 25
12.00 305 H-48A 20.80 374.40 1.80 499.20 2.40 748.80 3.60 25
2.00 51 H-49 190.40 571.20 0.30 761.60 0.40 1142.40 0.60 25
2.50 64 H-50 155.00 581.30 0.38 775.00 0.50 1162.50 0.75 25
3.00 76 H-51 130.00 585.00 0.45 780.00 0.60 1170.00 0.90 25
3.50 89 H-52 106.40 558.60 0.53 744.80 0.70 1117.20 1.05 25
4.00 102 H-53 91.20 547.20 0.60 729.60 0.80 1094.40 1.20 25
4.50 114 H-54 78.40 529.20 0.68 705.60 0.90 1058.40 1.35 25
1-1/2 3/4
5.00 127 H-55 71.20 534.00 0.75 712.00 1.00 1068.00 1.50 25
38mm 19mm
5.50 140 H-55A 64.00 528.00 0.83 704.00 1.10 1056.00 1.65 25
WIRE 6.00 152 H-56 58.40 525.60 0.90 700.80 1.20 1051.20 1.80 25
.225 x 7.00 178 H-56A 49.60 520.80 1.05 694.40 1.40 1041.60 2.10 25
.350 8.00 203 H-57 43.20 518.40 1.20 691.20 1.60 1036.80 2.40 25
10.00 254 H-48 34.40 516.00 1.50 688.00 2.00 1032.00 3.00 25
12.00 305 H-58A 28.80 518.40 1.80 691.20 2.40 1036.80 3.60 25
2.50 64 H-70 260.00 975.00 0.38 1300.00 0.50 1950.00 0.75 25
3.00 76 H-71 200.00 900.00 0.45 1200.00 0.60 1800.00 0.90 25
3.50 89 H-72 170.00 892.50 0.53 1190.00 0.70 1785.00 1.05 25
4.00 102 H-73 150.00 900.00 0.60 1200.00 0.80 1800.00 1.20 25
4.50 114 H-74 120.00 810.00 0.68 1080.00 0.90 1620.00 1.35 25
2 1 5.00 127 H-75 110.00 825.00 0.75 1100.00 1.00 1650.00 1.50 25
51mm 25mm 5.50 140 H-76 100.00 825.00 0.83 1100.00 1.10 1650.00 1.65 25
6.00 152 H-77 94.00 846.00 0.90 1128.00 1.20 1692.00 1.80 25
WIRE 7.00 178 H-79 82.00 861.00 1.05 1148.00 1.40 1722.00 2.10 25
.280 x
.470 8.00 203 H-80 73.00 876.00 1.20 1168.00 1.60 1752.00 2.40 10
10.00 254 H-82 55.00 825.00 1.50 1100.00 2.00 1650.00 3.00 10
12.00 305 H-83 42.00 756.00 1.80 1008.00 2.40 1512.00 3.60 10
information only. The color gold is a registered trademark of Barnes Group Inc.
9
EXTRA HEAVY DUTY DIE SPRINGS INCH
ROD HOLE
K
OC
ST
INCHES X 25.4 = MM IN FREE
LENGTH
LBS. X .454 = KG
Deflection for Optimum LIfe Deflection for Long Life *Maximum Deflection No.
Hole Rod Free Length Part Pounds
15% of Free Length 20% of Free Length 25% of Free Length
at per
Dia. Dia. Inch mm Number 1
/10" Deflection Load (lb) Deflection (in) Load (lb) Deflection (in) Load (lb) Deflection (in) Box
1.00 25 XH-100 22.00 33.00 0.15 44.00 0.20 55.00 0.25 200
1.25 32 XH-100A 16.80 30.00 0.19 40.00 0.25 50.00 0.31 200
1.50 38 XH-101 12.50 28.10 0.23 37.50 0.30 46.90 0.38 100
3/8 3/16 1.75 44 XH-101A 11.50 30.20 0.26 40.30 0.35 50.30 0.44 100
10mm 4.5mm
2.00 51 XH-102 9.00 27.00 0.30 36.00 0.40 45.00 0.50 100
WIRE 2.50 64 XH-103 7.00 26.30 0.38 35.00 0.50 43.80 0.63 100
.059 x .080 3.00 76 XH-104 6.50 29.30 0.45 39.00 0.60 48.80 0.75 100
12.00 305 XH-105 1.50 27.00 1.80 36.00 2.40 45.00 3.00 50
1.00 25 XH-110 32.00 48.00 0.15 64.00 0.20 80.00 0.25 100
1.25 32 XH-110A 24.00 45.00 0.19 60.00 0.25 75.00 0.31 100
1.50 38 XH-111 20.00 45.00 0.23 60.00 0.30 75.00 0.38 100
1/2 9/32 1.75 44 XH-111A 17.00 44.60 0.26 59.50 0.35 74.40 0.44 100
13mm 7mm 2.00 51 XH-112 14.00 42.00 0.30 56.00 0.40 70.00 0.50 100
2.50 64 XH-113 11.50 43.10 0.38 57.50 0.50 71.90 0.63 50
WIRE 3.00 76 XH-114 9.00 40.50 0.45 54.00 0.60 67.50 0.75 50
.084 x .097 3.50 89 XH-115 8.00 42.00 0.53 56.00 0.70 70.00 0.88 50
12.00 305 XH-116 2.50 45.00 1.80 60.00 2.40 75.00 3.00 50
1.00 25 XH-120 63.00 94.50 0.15 126.00 0.20 157.50 0.25 100
1.25 32 XH-120A 47.00 88.10 0.19 117.50 0.25 146.90 0.31 100
1.50 38 XH-121 38.00 85.50 0.23 114.00 0.30 142.50 0.38 50
1.75 44 XH-121A 32.00 84.00 0.26 112.00 0.35 140.00 0.44 50
5/8 11/32 2.00 51 XH-122 29.00 87.00 0.30 116.00 0.40 145.00 0.50 50
16mm 8.5mm
2.50 64 XH-123 22.00 82.00 0.38 110.00 0.50 137.50 0.63 50
3.00 76 XH-124 19.00 85.50 0.45 114.00 0.60 142.50 0.75 50
WIRE 3.50 89 XH-125 16.00 84.00 0.53 112.00 0.70 140.00 0.88 50
.110 x .126 4.00 102 XH-126 13.50 81.00 0.60 108.00 0.80 135.00 1.00 50
12.00 305 XH-127 4.50 81.00 1.80 108.00 2.40 135.00 3.00 50
1.00 25 XH-1 140.00 210.00 0.15 280.00 0.20 350.00 0.25 50
1.25 32 XH-1A 110.00 206.30 0.19 275.00 0.25 343.80 0.31 50
1.50 38 XH-2 89.00 200.30 0.23 267.00 0.30 333.80 0.38 50
1.75 44 XH-2A 75.00 196.90 0.26 262.50 0.35 328.10 0.44 50
2.00 51 XH-3 66.00 204.00 0.30 272.00 0.40 340.00 0.50 50
2.50 64 XH-4 50.00 187.50 0.38 250.00 0.50 312.50 0.63 50
3/4 3/8 3.00 76 XH-5 40.50 182.30 0.45 243.00 0.60 303.80 0.75 50
19mm 9.5mm
3.50 89 XH-6 34.50 181.10 0.53 241.50 0.70 301.90 0.88 50
4.00 102 XH-7 30.00 180.00 0.60 240.00 0.80 300.00 1.00 50
4.50 114 XH-8 26.50 178.90 0.68 238.50 0.90 298.10 1.13 50
5.00 127 XH-9 23.50 146.30 0.75 235.00 1.00 293.80 1.25 50
WIRE 5.50 140 XH-10 21.50 177.40 0.83 236.50 1.10 295.60 1.38 50
.135 x .165 6.00 152 XH-11 19.50 175.50 0.90 234.00 1.20 292.50 1.50 50
12.00 305 XH-12 9.50 171.00 1.80 228.00 2.40 285.00 3.00 50
information only. The color green is a registered trademark of Barnes Group Inc.
Dos and Donts.
10
EXTRA HEAVY-DUTY DIE SPRINGS INCH GREEN
Hole Rod Free Length Part Pounds Optimum LIfe Long Life
25% of Free Length
at 15% of Free Length 20% of Free Length per
Dia. Dia. Number 1
/10" Deflection Box
1.50 38 XH-13 160.00 360.00 0.23 480.00 0.30 600.00 0.38 50

2.00 51 XH-14 116.00 348.00 0.30 464.00 0.40 580.00 0.50 50
2.50 64 XH-15 89.60 336.00 0.38 448.00 0.50 560.00 0.63 50
3.00 76 XH-16 73.60 331.20 0.45 441.60 0.60 552.00 0.75 25
1 1/2 3.50 89 XH-17 62.40 327.60 0.53 436.80 0.70 546.00 0.88 25
26mm 12.5mm 4.00 102 XH-18 55.20 331.20 0.60 441.60 0.80 552.00 1.00 25
4.50 114 XH-19 48.80 329.40 0.68 439.20 0.90 549.00 1.13 25
WIIRE 5.00 127 XH-20 43.20 324.00 0.75 432.00 1.00 540.00 1.25 25
.160 x
.187 x 6.00 152 XH-21 36.00 324.00 0.90 432.00 1.20 540.00 1.50 25
.224 12.00 305 XH-22A 17.60 316.80 1.80 422.40 2.40 528.00 3.00 25
2.00 51 XH-37 192.00 576.00 0.30 768.00 0.40 960.00 0.50 50
2.50 64 XH-38 144.00 540.00 0.38 720.00 0.50 900.00 0.63 25
3.00 76 XH-39 118.40 532.80 0.45 710.40 0.60 888.00 0.75 25
3.50 89 XH-40 100.80 529.20 0.53 705.60 0.70 882.00 0.88 25
4.00 102 XH-41 84.00 504.00 0.60 672.00 0.80 840.00 1.00 25
1-1/4 5/8
4.50 114 XH-42 78.40 529.20 0.68 705.60 0.90 882.00 1.13 25
32mm 15.5mm 5.00 127 XH-43 68.00 510.00 0.75 680.00 1.00 850.00 1.25 25
WIRE 6.00 152 XH-45 56.00 504.00 0.90 672.00 1.20 840.00 1.50 25
.204 x 8.00 203 XH-47 41.60 499.20 1.20 665.60 1.60 832.00 2.00 25
.244 x 10.00 254 XH-48 33.60 504.00 1.50 672.00 2.00 840.00 2.50 25
.288
12.00 305 XH-48A 26.40 475.20 1.80 633.60 2.40 792.00 3.00 25
2.00 51 XH-49 376.00 1128.00 0.30 1504.00 0.40 1888.00 0.50 25
2.50 64 XH-50 294.40 1104.00 0.38 1472.00 0.50 1840.00 0.63 25
3.00 76 XH-51 231.20 1040.40 0.45 1387.20 0.60 1734.00 0.75 25
3.50 89 XH-52 196.00 1029.00 0.53 1372.00 0.70 1715.00 0.88 25
4.00 102 XH-53 171.20 1027.20 0.60 1369.60 0.80 1712.00 1.00 25
1-1/2 3/4
4.50 114 XH-54 148.00 999.00 0.68 1332.00 0.90 1665.00 1.13 25
38mm 19mm 5.00 127 XH-55 136.00 1020.00 0.75 1360.00 1.00 1700.00 1.25 25
WIRE 6.00 152 XH-56 110.40 993.60 0.90 1324.80 1.20 1656.00 1.50 25
.278 x 8.00 203 XH-57 80.80 969.60 1.20 1292.80 1.60 1616.00 2.00 25
.323 x 10.00 254 XH-58 67.20 1008.00 1.50 1344.00 2.00 1680.00 2.50 25
.343
12.00 305 XH-58A 54.40 979.20 1.80 1305.60 2.40 1632.00 3.00 25
2.50 64 XH-70 381.60 1431.00 0.38 1908.00 0.50 2385.00 0.63 25
3.00 76 XH-71 312.00 1404.00 0.45 1872.00 0.60 2340.00 0.75 25
3.50 89 XH-72 254.40 1335.60 0.53 1780.80 0.70 2226.00 1.88 25
4.00 102 XH-73 220.00 1320.00 0.60 1760.00 0.80 2200.00 1.00 25
2 1 4.50 114 XH-74 188.80 1274.40 0.68 1699.20 0.90 2124.00 1.13 25
51mm 25mm 5.00 127 XH-75 172.80 1296.00 0.75 1728.00 1.00 2160.00 1.25 25
WIRE 6.00 152 XH-77 141.60 1274.40 0.90 1699.20 1.20 2124.00 1.50 25
.308 x 8.00 203 XH-80 100.00 1200.00 1.20 1600.00 1.60 2000.00 2.00 10
.387 x 10.00 254 XH-82 84.00 1260.00 1.50 1680.00 2.00 2100.00 2.50 10
.450 12.00 305 XH-83 71.20 1281.60 1.80 1708.80 2.40 2136.00 3.00 10
*Deflection values shown represent compressed lengths near solid and are for design information only. Let us quote your specials!
The color green is a registered trademark of Barnes Group Inc.
STANDARD TOLERANCES FOR FREE LENGTHS

+.093
Up to 2.499 -.000
+.250
+.125 8 to 9.999
2.5 to 4.999 -.000 -.000
5 to 7.999 +.187 10 to 12 +.375

-.000 -.000
11
MM x .039837 = INCHES
KG X 2.20463= LBS.
LIGHT DUTY DIE SPRINGS METRIC ISO SPECIFICATION SERIES GREEN

LOAD DEFLECTION
Hole Rod Free Load
Dia. Dia. Length For Long Life For Long Life *Maximum Operating Def.
PART at (25% of free length) (30% of free length) (35% of free length)
NUMBER 1mm Maximum Number
(mm) (mm) (mm) Def. Load (N) Deflection Load (N) Deflection Load (N) Deflection Deflection Box
(N) mm mm mm
A B C
25 ILD010025 10.0 62.5 6.3 75.0 7.5 87.5 8.8 10.3 200
32 ILD010032 8.5 68.0 8.0 81.6 9.6 95.2 11.2 13.1 200
38 ILD010038 6.8 64.6 9.5 77.5 11.4 90.4 13.3 15.6 100
10 5 44 ILD010044 6.0 66.0 11.0 79.2 13.2 92.4 15.4 18.0 100
(3/8") (3/16") 51 ILD010051 5.0 63.8 12.8 76.5 15.3 89.3 17.9 20.9 100
64 ILD010064 4.3 68.8 16.0 82.6 19.2 96.3 22.4 26.0 100
76 ILD010076 3.2 60.8 19.0 73.0 22.8 85.1 26.6 31.2 100
305 ILD010305 1.1 83.9 76.3 100.7 91.5 117.4 106.8 125.0 50
25 ILD012025 17.9 111.9 6.3 134.3 7.5 156.6 8.8 10.3 100
32 ILD012032 16.4 131.2 8.0 157.4 9.6 183.7 11.2 13.1 100
38 ILD012038 13.6 129.2 9.5 155.0 11.4 180.9 13.3 15.6 100
44 ILD012044 12.1 133.1 11.0 159.7 13.2 186.3 15.4 18.0 100
12.5 6.3 51 ILD012051
(1/2") (9/32") 11.4 145.4 12.8 174.4 15.3 203.5 17.9 20.9 100
64 ILD012064 9.3 148.8 16.0 178.6 19.2 208.3 22.4 26.3 50
76 ILD012076 7.1 134.9 19.0 161.9 22.8 188.9 26.6 31.2 50
89 ILD012089 5.4 120.2 22.3 144.2 26.7 168.2 31.2 36.5 50
305 ILD012305 1.4 106.8 76.3 128.1 91.5 149.5 106.8 125.0 50
25 ILD016025 23.4 146.3 6.3 175.5 7.5 204.8 8.8 10.3 100
32 ILD016032 22.9 183.2 8.0 219.8 9.6 256.5 11.2 13.1 100
38 ILD016038 19.3 183.4 9.5 220.0 11.4 256.7 13.3 15.6 50
44 ILD016044 17.1 188.1 11.0 225.7 13.2 263.3 15.4 18.0 50
16 8 51 ILD016051 15.7 200.2 12.8 240.2 15.3 280.2 17.9 20.9 50
(5/8") (11/32") 64 ILD016064 10.7 171.2 16.0 205.4 19.2 239.7 22.4 26.3 50
76 ILD016076 10.0 190.0 19.0 228.0 22.8 266.0 26.6 31.2 50
89 ILD016089 8.6 191.4 22.3 229.6 26.7 267.9 31.2 36.5 50
102 ILD016102 7.8 198.9 25.5 238.7 30.6 278.5 35.7 41.8 50
305 ILD016305 2.5 190.6 76.3 228.8 91.5 266.9 106.8 125.0 50
25 ILD020025 55.8 348.8 6.3 418.5 7.5 488.3 8.8 10.2 50
32 ILD020032 45.0 360.0 8.0 432.0 9.6 504.0 11.2 12.5 50
38 ILD020038 33.3 316.4 9.5 379.6 11.4 442.9 13.3 15.0 50
44 ILD020044 30.0 330.0 11.0 396.0 13.2 462.0 15.4 18.0 50
51 ILD020051 24.5 312.4 12.8 374.9 15.3 437.3 17.9 20.0 50
64 ILD020064 20.0 320.0 16.0 384.0 19.2 448.0 22.4 25.0 50
20 10 76 ILD020076 16.0 304.0 19.0 364.8 22.8 425.6 26.6 30.0 50
(3/4") (3/8") 89 ILD020089 14.0 311.5 22.3 373.8 26.7 436.1 31.2 35.0 50
102 ILD020102 12.0 306.0 25.5 367.2 30.6 428.4 35.7 41.0 50
115 ILD020115 10.9 313.4 28.8 376.1 34.5 438.7 40.3 46.0 50
127 ILD020127 9.5 301.6 31.8 362.0 38.1 422.3 44.5 51.0 50
139 ILD020139 8.4 291.9 34.8 350.3 41.7 408.7 48.7 56.0 50
152 ILD020152 7.5 285.0 38.0 342.0 45.6 399.0 53.2 61.0 50
305 ILD020305 4.0 305.0 76.3 366.0 91.5 427.0 106.8 122.0 50
25 ILD025025 100.0 625.0 6.3 750.0 7.5 875.0 8.8 10.2 50
32 ILD025032 80.3 642.4 8.0 770.9 9.6 899.4 11.2 12.5 50
38 ILD025038 62.0 589.0 9.5 706.8 11.4 824.6 13.3 15.0 50
44 ILD025044 52.9 581.9 11.0 698.3 13.2 814.7 15.4 18.0 50
25 12.5 51 ILD025051 44.0 561.0 12.8 673.2 15.3 785.4 17.9 20.0 50
(1") (1/2") 64 ILD025064 35.2 563.2 16.0 675.8 19.2 788.5 22.4 25.0 50
76 ILD025076 28.0 532.0 19.0 638.4 22.8 744.8 26.6 30.0 25
89 ILD025089 24.0 534.0 22.3 640.8 26.7 747.6 31.2 35.0 25
102 ILD025102 21.1 538.1 25.5 645.7 30.6 753.3 35.7 41.0 25
115 ILD025115 18.7 537.6 28.8 645.2 34.5 752.7 40.3 46.0 25
*Tabulated deflections values shown represent compressed lengths near solid and are for design information only.
12
KG X 2.20463= LBS.
LIGHT DUTY DIE SPRINGS METRIC ISO SPECIFICATION SERIES GREEN

LOAD DEFLECTION TABLE
Hole Rod Free Load
Dia. Dia. Length at For Long Life For Long Life *Maximum OperatingDef.
PART 1mm
(25% of free length) (30% of free length) (35% of free length)
NUMBER Maximum Number
(N) mm mm mm
A B C
127 ILD025127 16.7 530.2 31.8 636.3 38.1 742.3 44.5 51.0 25
139 ILD025139 15.3 531.7 34.8 638.0 41.7 744.3 48.7 56.0 25
25 12.5 152 ILD025152 14.0 532.0 38.0 638.4 45.6 744.8 53.2 61.0 25
(1") (1/2") 178 ILD025178 12.5 556.3 44.5 667.5 53.4 778.8 62.3 71.0 25
203 ILD025203 10.4 527.8 50.8 633.4 60.9 738.9 71.1 81.0 25
305 ILD025305 7.0 533.8 76.3 640.5 91.5 747.3 106.8 122.0 25
38 ILD032038 94.0 893.0 9.5 1071.6 11.4 1250.2 13.3 15.0 50
44 ILD032044 79.5 874.5 11.0 1049.4 13.2 1224.3 15.4 18.0 50
51 ILD032051 67.0 854.3 12.8 1025.1 15.3 1196.0 17.9 20.0 50
64 ILD032064 53.0 848.0 16.0 1017.6 19.2 1187.2 22.4 25.0 25
76 ILD032076 44.0 836.0 19.0 1003.2 22.8 1170.4 26.6 30.0 25
89 ILD032089 37.2 827.7 22.3 993.2 26.7 1158.8 31.2 35.0 25
102 ILD032102 32.0 816.0 25.5 979.2 30.6 1142.4 35.7 41.0 25
32 16 ILD032115
(1 1/4") (5/8") 115 29.0 833.8 28.8 1000.5 34.5 1167.3 40.3 46.0 25
127 ILD032127 25.0 793.8 31.8 952.5 38.1 1111.3 44.5 51.0 25
139 ILD032139 23.0 799.3 34.8 959.1 41.7 1119.0 48.7 56.0 25
152 ILD032152 21.5 817.0 38.0 980.4 45.6 1143.8 53.2 61.0 25
178 ILD032178 18.2 809.9 44.5 971.9 53.4 1133.9 62.3 71.0 25
203 ILD032203 15.8 801.9 50.8 962.2 60.9 1122.6 71.1 81.0 25
254 ILD032254 12.5 793.8 63.5 952.5 76.2 1111.3 88.9 102.0 25
305 ILD032305 10.3 785.4 76.3 942.5 91.5 1099.5 106.8 122.0 25
51 ILD040051 92.0 1173.0 12.8 1407.6 15.3 1642.2 17.9 20.0 25
64 ILD040064 73.0 1168.0 16.0 1401.6 19.2 1635.2 22.4 25.0 25
76 ILD040076 63.0 1197.0 19.0 1436.4 22.8 1675.8 26.6 30.0 25
89 ILD040089 51.0 1134.8 22.3 1361.7 26.7 1588.7 31.2 35.0 25
102 ILD040102 43.0 1096.5 25.5 1315.8 30.6 1535.1 35.7 41.0 25
115 ILD040115 39.6 1138.5 28.8 1366.2 34.5 1593.9 40.3 46.0 25
40 20 ILD040127
(1 1/2") (3/4") 127 37.0 1174.8 31.8 1409.7 38.1 1644.7 44.5 51.0 25
139 ILD040139 32.0 1112.0 34.8 1334.4 41.7 1556.8 48.7 56.0 25
152 ILD040152 28.0 1064.0 38.0 1276.8 45.6 1489.6 53.2 61.0 25
178 ILD040178 25.2 1121.4 44.5 1345.7 53.4 1570.0 62.3 71.0 25
203 ILD040203 22.7 1152.0 50.8 1382.4 60.9 1612.8 71.1 81.0 25
254 ILD040254 17.0 1079.5 63.5 1295.4 76.2 1511.3 88.9 102.0 25
305 ILD040305 14.8 1128.5 76.3 1354.2 91.5 1579.9 106.8 122.0 25
64 ILD050064 156.0 2496.0 16.0 2995.2 19.2 3494.4 22.4 25.0 25
76 ILD050076 125.0 2375.0 19.0 2850.0 22.8 3325.0 26.6 30.0 25
89 ILD050089 109.0 2425.3 22.3 2910.3 26.7 3395.4 31.2 35.0 25
102 ILD050102 94.0 2397.0 25.5 2876.4 30.6 3355.8 35.7 41.0 25
115 ILD050115 81.0 2328.8 28.8 2794.5 34.5 3260.3 40.3 46.0 25
50 25 127 ILD050127 71.0 2254.3 31.8 2705.1 38.1 3156.0 44.5 51.0 25
(2") (1") 139 ILD050139 66.5 2310.9 34.8 2773.1 41.7 3235.2 48.7 56.0 25
152 ILD050152 60.0 2280.0 38.0 2736.0 45.6 3192.0 53.2 61.0 25
178 ILD050178 52.0 2314.0 44.5 2776.8 53.4 3239.6 62.3 71.0 25
203 ILD050203 44.0 2233.0 50.8 2679.6 60.9 3126.2 71.1 81.0 10
254 ILD050254 35.0 2222.5 63.5 2667.0 76.2 3111.5 88.9 102.0 10
305 ILD050305 28.5 2173.1 76.3 2607.8 91.5 3042.4 106.8 122.0 10
76 ILD063076 189.0 3591.0 19.0 4309.2 22.8 5027.4 26.6 30.0 25
89 ILD063089 158.0 3515.5 22.3 4218.6 26.7 4921.7 31.2 35.0 25
102 ILD063102 131.0 3340.5 25.5 4008.6 30.6 4676.7 35.7 41.0 25
115 ILD063115 116.0 3335.0 28.8 4002.0 34.5 4669.0 40.3 46.0 10
63 38 127 ILD063127 103.0 3270.3 31.8 3924.3 38.1 4578.4 44.5 51.0 10
(2 1/2") (1 1/2") 152 ILD063152 84.3 3203.4 38.0 3844.1 45.6 4484.8 53.2 61.0 10
178 ILD063178 71.5 3181.8 44.5 3818.1 53.4 4454.5 62.3 71.0 10
203 ILD063203 61.7 3131.3 50.8 3757.5 60.9 4383.8 71.1 81.0 10
254 ILD063254 47.0 2984.5 63.5 3581.4 76.2 4178.3 88.9 102.0 10
305 ILD063305 38.2 2912.8 76.3 3495.3 91.5 4077.9 106.8 122.0 10
13
KG X 2.20463= LBS.
MEDIUM DUTY DIE SPRINGS METRIC ISO SPECIFICATION SERIES BLUE

Hole Rod Free Load
Dia. Dia. Length at For Long Life For Long Life *Maximum Operating Def.
PART 1mm
(N) mm mm mm
A B C
25 IMD010025 16.0 80.0 5.0 100.0 6.3 120.0 7.5 9.5 200
32 IMD010032 13.0 83.2 6.4 104.0 8.0 124.8 9.6 12.2 200
38 IMD010038 11.9 90.4 7.6 113.1 9.5 135.7 11.4 14.4 100
10 5 44 IMD010044 10.3 90.6 8.8 113.3 11.0 136.0 13.2 16.7 100
(3/8") (3/16") 51 IMD010051 8.9 90.8 10.2 113.5 12.8 136.2 15.3 19.4 100
64 IMD010064 7.5 96.0 12.8 120.0 16.0 144.0 19.2 24.3 100
76 IMD010076 5.3 80.6 15.2 100.7 19.0 120.8 22.8 28.9 100
305 IMD010305 1.6 97.6 61.0 122.0 76.3 146.4 91.5 116.0 50
25 IMD012025 30.0 150.0 5.0 187.5 6.3 225.0 7.5 9.5 100
32 IMD012032 24.8 158.7 6.4 198.4 8.0 238.1 9.6 12.2 100
38 IMD012038 21.4 162.6 7.6 203.3 9.5 244.0 11.4 14.4 100
44 IMD012044 18.5 162.8 8.8 203.5 11.0 244.2 13.2 16.7 100
12.5 6.3 51 IMD012051 15.5 158.1 10.2 197.6 12.8 237.2 15.3 19.4 100
(1/2") (9/32") 64 IMD012064 12.1 154.9 12.8 193.6 16.0 232.3 19.2 24.3 50
76 IMD012076 10.2 155.0 15.2 193.8 19.0 232.6 22.8 28.9 50
89 IMD012089 8.4 149.5 17.8 186.9 22.3 224.3 26.7 33.8 50
305 IMD012305 2.1 128.1 61.0 160.1 76.3 192.2 91.5 116.0 50
25 IMD016025 49.4 247.0 5.0 308.8 6.3 370.5 7.5 9.5 100
32 IMD016032 37.1 237.4 6.4 296.8 8.0 356.2 9.6 12.2 100
38 IMD016038 33.9 257.6 7.6 322.1 9.5 386.5 11.4 14.4 50
44 IMD016044 30.0 264.0 8.8 330.0 11.0 396.0 13.2 16.7 50
16 8 51 IMD016051 26.4 269.3 10.2 336.6 12.8 403.9 15.3 19.4 50
(5/8") (11/32") 64 IMD016064 20.5 262.4 12.8 328.0 16.0 393.6 19.2 24.3 50
76 IMD016076 17.8 270.6 15.2 338.2 19.0 405.8 22.8 28.9 50
89 IMD016089 15.2 270.6 17.8 338.2 22.3 405.8 26.7 33.8 50
102 IMD016102 13.5 275.4 20.4 344.3 25.5 413.1 30.6 38.8 50
305 IMD016305 4.8 292.8 61.0 366.0 76.3 439.2 91.5 116.0 50
25 IMD020025 98.0 490.0 5.0 612.5 6.3 735.0 7.5 9.4 50
32 IMD020032 72.6 464.6 6.4 580.8 8.0 697.0 9.6 12.0 50
38 IMD020038 56.0 425.6 7.6 532.0 9.5 638.4 11.4 14.0 50
44 IMD020044 47.5 418.0 8.8 522.5 11.0 627.0 13.2 16.5 50
51 IMD020051 41.7 425.3 10.2 531.7 12.8 638.0 15.3 19.0 50
64 IMD020064 32.3 413.4 12.8 516.8 16.0 620.2 19.2 24.0 50
20 10 76 IMD020076 25.1 381.5 15.2 476.9 19.0 572.3 22.8 28.0 50
(3/4") (3/8") 89 IMD020089 22.0 391.6 17.8 489.5 22.3 587.4 26.7 33.0 50
102 IMD020102 19.8 403.9 20.4 504.9 25.5 605.9 30.6 38.0 50
115 IMD020115 18.1 416.3 23.0 520.4 28.8 624.5 34.5 43.0 50
127 IMD020127 16.6 421.6 25.4 527.1 31.8 632.5 38.1 48.0 50
139 IMD020139 15.1 419.8 27.8 524.7 34.8 629.7 41.7 52.0 50
152 IMD020152 13.2 401.3 30.4 501.6 38.0 601.9 45.6 57.0 50
305 IMD020305 6.1 372.1 61.0 465.1 76.3 558.2 91.5 114.0 50
25 IMD025025 147.0 735.0 5.0 918.8 6.3 1102.5 7.5 9.4 50
32 IMD025032 118.0 755.2 6.4 944.0 8.0 1132.8 9.6 12.0 50
38 IMD025038 93.0 706.8 7.6 883.5 9.5 1060.2 11.4 14.0 50
44 IMD025044 80.8 711.0 8.8 888.8 11.0 1066.6 13.2 16.5 50
51 IMD025051 68.6 699.7 10.2 874.7 12.8 1049.6 15.3 19.0 50
25 12.5 64 IMD025064 53.0 678.4 12.8 848.0 16.0 1017.6 19.2 24.0 50
(1") (1/2") 76 IMD025076 43.2 656.6 15.2 820.8 19.0 985.0 22.8 28.0 25
89 IMD025089 38.2 680.0 17.8 850.0 22.3 1019.9 26.7 33.0 25
102 IMD025102 33.0 673.2 20.4 841.5 25.5 1009.8 30.6 38.0 25
115 IMD025115 28.0 644.0 23.0 805.0 28.8 966.0 34.5 43.0 25
127 IMD025127 25.9 657.9 25.4 822.3 31.8 986.8 38.1 48.0 25
139 IMD025139 23.2 645.0 27.8 806.2 34.8 967.4 41.7 52.0 25
14
KG X 2.20463= LBS.
MEDIUM DUTY DIE SPRINGS METRIC ISO SPECIFICATION SERIES BLUE

Hole Rod Free Load
PART 1mm
(N) mm mm mm
A B C
152 IMD025152 20.8 632.3 30.4 790.4 38.0 948.5 45.6 57.0 25
25 12.5 178 IMD025178 17.8 633.7 35.6 792.1 44.5 950.5 53.4 67.0 25
(1") (1/2") 203 IMD025203 15.8 641.5 40.6 801.9 50.8 962.2 60.9 76.0 25
305 IMD025305 10.2 622.2 61.0 777.8 76.3 933.3 91.5 114.0 25
38 IMD032038 185.0 1406.0 7.6 1757.5 9.5 2109.0 11.4 14.0 50
44 IMD032044 158.0 1390.4 8.8 1738.0 11.0 2085.6 13.2 16.5 50
51 IMD032051 134.0 1366.8 10.2 1708.5 12.8 2050.2 15.3 19.0 50
64 IMD032064 99.0 1267.2 12.8 1584.0 16.0 1900.8 19.2 24.0 25
76 IMD032076 80.5 1223.6 15.2 1529.5 19.0 1835.4 22.8 28.0 25
89 IMD032089 69.1 1230.0 17.8 1537.5 22.3 1845.0 26.7 33.0 25
102 IMD032102 58.8 1199.5 20.4 1499.4 25.5 1799.3 30.6 38.0 25
32 16 115 IMD032115 51.5 1184.5 23.0 1480.6 28.8 1776.8 34.5 43.0 25
(1 1/4") (5/8") 127 IMD032127 44.8 1137.9 25.4 1422.4 31.8 1706.9 38.1 48.0 25
139 IMD032139 42.3 1175.9 27.8 1469.9 34.8 1763.9 41.7 52.0 25
152 IMD032152 37.8 1149.1 30.4 1436.4 38.0 1723.7 45.6 57.0 25
178 IMD032178 32.5 1157.0 35.6 1446.3 44.5 1735.5 53.4 67.0 25
203 IMD032203 28.9 1173.3 40.6 1466.7 50.8 1760.0 60.9 76.0 25
254 IMD032254 21.4 1087.1 50.8 1358.9 63.5 1630.7 76.2 95.0 25
305 IMD032305 18.3 1116.3 61.0 1395.4 76.3 1674.5 91.5 114.0 25
51 IMD040051 181.6 1852.3 10.2 2315.4 12.8 2778.5 15.3 19.0 25
64 IMD040064 140.0 1792.0 12.8 2240.0 16.0 2688.0 19.2 24.0 25
76 IMD040076 108.0 1641.6 15.2 2052.0 19.0 2462.4 22.8 28.0 25
89 IMD040089 90.7 1614.5 17.8 2018.1 22.3 2421.7 26.7 33.0 25
102 IMD040102 81.0 1652.4 20.4 2065.5 25.5 2478.6 30.6 38.0 25
115 IMD040115 71.8 1651.4 23.0 2064.3 28.8 2477.1 34.5 43.0 25
40 20 127 IMD040127 62.7 1592.6 25.4 1990.7 31.8 2388.9 38.1 48.0 25
(1 1/2") (3/4") 139 IMD040139 57.5 1598.5 27.8 1998.1 34.8 2397.8 41.7 52.0 25
152 IMD040152 51.6 1568.6 30.4 1960.8 38.0 2353.0 45.6 57.0 25
178 IMD040178 44.1 1570.0 35.6 1962.5 44.5 2354.9 53.4 67.0 25
203 IMD040203 36.7 1490.0 40.6 1862.5 50.8 2235.0 60.9 76.0 25
254 IMD040254 30.1 1529.1 50.8 1911.4 63.5 2293.6 76.2 95.0 25
305 IMD040305 24.6 1500.6 61.0 1875.8 76.3 2250.9 91.5 114.0 25
64 IMD050064 209.0 2675.2 12.8 3344.0 16.0 4012.8 19.2 24.0 25
76 IMD050076 168.0 2553.6 15.2 3192.0 19.0 3830.4 22.8 28.0 25
89 IMD050089 140.0 2492.0 17.8 3115.0 22.3 3738.0 26.7 33.0 25
102 IMD050102 119.0 2427.6 20.4 3034.5 25.5 3641.4 30.6 38.0 25
115 IMD050115 106.0 2438.8 23.0 3047.5 28.8 3657.0 34.5 43.0 25
127 IMD050127 97.0 2463.8 25.4 3079.8 31.8 3695.7 38.1 48.0 25
50 25 139 IMD050139 87.0 2418.6 27.8 3023.3 34.8 3627.9 41.7 52.0 25
(2") (1") IMD050152
152 80.0 2432.0 30.4 3040.0 38.0 3648.0 45.6 57.0 25
178 IMD050178 69.5 2474.2 35.6 3092.8 44.5 3711.3 53.4 67.0 25
203 IMD050203 59.8 2427.9 40.6 3034.9 50.8 3641.8 60.9 76.0 10
229 IMD050229 50.9 2331.2 45.8 2914.0 57.3 3496.8 68.7 86.0 10
254 IMD050254 43.9 2230.1 50.8 2787.7 63.5 3345.2 76.2 95.0 10
305 IMD050305 38.6 2354.6 61.0 2943.3 76.3 3531.9 91.5 114.0 10
76 IMD063076 312.0 4742.4 15.2 5928.0 19.0 7113.6 22.8 28.0 25
89 IMD063089 260.0 4628.0 17.8 5785.0 22.3 6942.0 26.7 33.0 25
102 IMD063102 221.0 4508.4 20.4 5635.5 25.5 6762.6 30.6 38.0 25
115 IMD063115 187.0 4301.0 23.0 5376.3 28.8 6451.5 34.5 43.0 10
127 IMD063127 168.0 4267.2 25.4 5334.0 31.8 6400.8 38.1 48.0 10
63 38 IMD063152
(2 1/2") (1 1/2") 152 136.0 4134.4 30.4 5168.0 38.0 6201.6 45.6 57.0 10
178 IMD063178 114.0 4058.4 35.6 5073.0 44.5 6087.6 53.4 67.0 10
203 IMD063203 100.0 4060.0 40.6 5075.0 50.8 6090.0 60.9 76.0 10
229 IMD063229 89.2 4085.4 45.8 5106.7 57.3 6128.0 68.7 86.0 10
254 IMD063254 78.4 3982.7 50.8 4978.4 63.5 5974.1 76.2 95.0 10
305 IMD063305 64.7 3946.7 61.0 4933.4 76.3 5920.1 91.5 114.0 10
15
KG X 2.20463= LBS.
HEAVY DUTY DIE SPRINGS METRIC ISO SPECIFICATION SERIES RED

Hole Rod Free Load
PART 1mm
(mm) (mm) (mm) Def. Deflection Box
Load (N) Deflection Load (N) Deflection Load (N) Deflection
(N) mm mm mm
A B C
25 IHD010025 22.1 82.9 3.8 110.5 5.0 138.1 6.3 7.5 200
32 IHD010032 17.5 84.0 4.8 112.0 6.4 140.0 8.0 9.6 200
38 IHD010038 17.1 97.5 5.7 130.0 7.6 162.5 9.5 11.4 100
10 5 44 IHD010044 15.0 99.0 6.6 132.0 8.8 165.0 11.0 13.2 100
(3/8") (3/16") 51 IHD010051 12.8 97.9 7.7 130.6 10.2 163.2 12.8 15.3 100
64 IHD010064 10.7 102.7 9.6 137.0 12.8 171.2 16.0 19.2 100
76 IHD010076 7.5 85.5 11.4 114.0 15.2 142.5 19.0 22.8 100
305 IHD010305 2.1 96.1 45.8 128.1 61.0 160.1 76.3 91.5 50
25 IHD012025 42.1 157.9 3.8 210.5 5.0 263.1 6.3 7.5 100
32 IHD012032 33.2 159.4 4.8 212.5 6.4 265.6 8.0 9.6 100
38 IHD012038 29.3 167.0 5.7 222.7 7.6 278.4 9.5 11.4 100
44 IHD012044 24.6 162.4 6.6 216.5 8.8 270.6 11.0 13.2 100
12.5 6.3 51 IHD012051 19.6 149.9 7.7 199.9 10.2 249.9 12.8 15.3 100
(1/2") (9/32") 64 IHD012064 15.0 144.0 9.6 192.0 12.8 240.0 16.0 19.2 50
76 IHD012076 13.2 150.5 11.4 200.6 15.2 250.8 19.0 22.8 50
89 IHD012089 11.4 152.2 13.4 202.9 17.8 253.7 22.3 26.7 50
305 IHD012305 2.8 128.1 45.8 170.8 61.0 213.5 76.3 91.5 50
25 IHD016025 75.7 283.9 3.8 378.5 5.0 473.1 6.3 7.5 100
32 IHD016032 52.8 253.4 4.8 337.9 6.4 422.4 8.0 9.6 100
38 IHD016038 48.5 276.5 5.7 368.6 7.6 460.8 9.5 11.4 50
44 IHD016044 42.8 282.5 6.6 376.6 8.8 470.8 11.0 13.2 50
16 8 51 IHD016051 37.1 283.8 7.7 378.4 10.2 473.0 12.8 15.3 50
(5/8") (11/32") 64 IHD016064 30.3 290.9 9.6 387.8 12.8 484.8 16.0 19.2 50
76 IHD016076 25.7 293.0 11.4 390.6 15.2 488.3 19.0 22.8 50
89 IHD016089 21.7 289.7 13.4 386.3 17.8 482.8 22.3 26.7 50
102 IHD016102 19.3 295.3 15.3 393.7 20.4 492.2 25.5 30.6 50
305 IHD016305 7.1 324.8 45.8 433.1 61.0 541.4 76.3 91.5 50
25 IHD020025 216.0 810.0 3.8 1080.0 5.0 1350.0 6.3 7.5 50
32 IHD020032 168.0 806.4 4.8 1075.2 6.4 1344.0 8.0 9.6 50
38 IHD020038 129.0 735.3 5.7 980.4 7.6 1225.5 9.5 11.0 50
44 IHD020044 112.0 739.2 6.6 985.6 8.8 1232.0 11.0 13.0 50
51 IHD020051 94.0 719.1 7.7 958.8 10.2 1198.5 12.8 15.0 50
64 IHD020064 72.1 692.2 9.6 922.9 12.8 1153.6 16.0 19.0 50
20 10 76 IHD020076 59.7 680.6 11.4 907.4 15.2 1134.3 19.0 23.0 50
(3/4") (3/8") 89 IHD020089 50.5 674.2 13.4 898.9 17.8 1123.6 22.3 27.0 50
102 IHD020102 44.2 676.3 15.3 901.7 20.4 1127.1 25.5 31.0 50
115 IHD020115 38.4 662.4 17.3 883.2 23.0 1104.0 28.8 35.0 50
127 IHD020127 34.1 649.6 19.1 866.1 25.4 1082.7 31.8 38.0 50
139 IHD020139 31.0 646.4 20.9 861.8 27.8 1077.3 34.8 42.0 50
152 IHD020152 28.2 643.0 22.8 857.3 30.4 1071.6 38.0 46.0 50
305 IHD020305 15.0 686.3 45.8 915.0 61.0 1143.8 76.3 91.0 50
25 IHD025025 375.0 1406.3 3.8 1875.0 5.0 2343.8 6.3 7.5 50
32 IHD025032 297.0 1425.6 4.8 1900.8 6.4 2376.0 8.0 9.6 50
38 IHD025038 219.0 1248.3 5.7 1664.4 7.6 2080.5 9.5 11.0 50
25 12.5 44 IHD025044 187.0 1234.2 6.6 1645.6 8.8 2057.0 11.0 13.0 50
(1") (1/2") 51 IHD025051 156.0 1193.4 7.7 1591.2 10.2 1989.0 12.8 15.0 50
64 IHD025064 123.0 1180.8 9.6 1574.4 12.8 1968.0 16.0 19.0 50
76 IHD025076 99.0 1128.6 11.4 1504.8 15.2 1881.0 19.0 23.0 25
16
KG X 2.20463= LBS.
HEAVY DUTY DIE SPRING METRIC ISO SPECIFICATION SERIES RED

Hole Rod Free Load
PART (15% of free length) (20% of free length) (25% of free length)
(N) mm mm mm
A B C
89 IHD025089 84.0 1121.4 13.4 1495.2 17.8 1869.0 22.3 27.0 25
102 IHD025102 73.0 1116.9 15.3 1489.2 20.4 1861.5 25.5 31.0 25
115 IHD025115 65.0 1121.3 17.3 1495.0 23.0 1868.8 28.8 35.0 25
127 IHD025127 57.7 1099.2 19.1 1465.6 25.4 1832.0 31.8 38.0 25
25 12.5 IHD025139
139 52.7 1098.8 20.9 1465.1 27.8 1831.3 34.8 42.0 25
(1") (1/2") IHD025152
152 47.8 1089.8 22.8 1453.1 30.4 1816.4 38.0 46.0 25
178 IHD025178 41.0 1094.7 26.7 1459.6 35.6 1824.5 44.5 53.0 25
203 IHD025203 35.8 1090.1 30.5 1453.5 40.6 1816.9 50.8 61.0 25
305 IHD025305 22.9 1047.7 45.8 1396.9 61.0 1746.1 76.3 91.0 25
38 IHD032038 388.0 2211.6 5.7 2948.8 7.6 3686.0 9.5 11.0 50
44 IHD032044 324.0 2138.4 6.6 2851.2 8.8 3564.0 11.0 13.0 50
51 IHD032051 272.0 2080.8 7.7 2774.4 10.2 3468.0 12.8 15.0 50
64 IHD032064 212.0 2035.2 9.6 2713.6 12.8 3392.0 16.0 19.0 25
76 IHD032076 172.0 1960.8 11.4 2614.4 15.2 3268.0 19.0 23.0 25
89 IHD032089 141.0 1882.4 13.4 2509.8 17.8 3137.3 22.3 27.0 25
102 IHD032102 122.0 1866.6 15.3 2488.8 20.4 3111.0 25.5 31.0 25
32 16
115 IHD032115 107.0 1845.8 17.3 2461.0 23.0 3076.3 28.8 35.0 25
(1 1/4") (5/8")
127 IHD032127 93.0 1771.7 19.1 2362.2 25.4 2952.8 31.8 38.0 25
139 IHD032139 86.0 1793.1 20.9 2390.8 27.8 2988.5 34.8 42.0 25
152 IHD032152 78.0 1778.4 22.8 2371.2 30.4 2964.0 38.0 46.0 25
178 IHD032178 67.2 1794.2 26.7 2392.3 35.6 2990.4 44.5 53.0 25
203 IHD032203 59.1 1799.6 30.5 2399.5 40.6 2999.3 50.8 61.0 25
254 IHD032254 46.4 1767.8 38.1 2357.1 50.8 2946.4 63.5 76.0 25
305 IHD032305 38.0 1738.5 45.8 2318.0 61.0 2897.5 76.3 91.0 25
51 IHD040051 350.0 2677.5 7.7 3570.0 10.2 4462.5 12.8 15.0 25
64 IHD040064 269.0 2582.4 9.6 3443.2 12.8 4304.0 16.0 19.0 25
76 IHD040076 219.0 2496.6 11.4 3328.8 15.2 4161.0 19.0 23.0 25
89 IHD040089 190.0 2536.5 13.4 3382.0 17.8 4227.5 22.3 27.0 25
102 IHD040102 163.0 2493.9 15.3 3325.2 20.4 4156.5 25.5 31.0 25
115 IHD040115 142.0 2449.5 17.3 3266.0 23.0 4082.5 28.8 35.0 25
40 20
127 IHD040127 128.0 2438.4 19.1 3251.2 25.4 4064.0 31.8 38.0 25
(1 1/2") (3/4")
139 IHD040139 115.0 2397.8 20.9 3197.0 27.8 3996.3 34.8 42.0 25
152 IHD040152 105.0 2394.0 22.8 3192.0 30.4 3990.0 38.0 46.0 25
178 IHD040178 89.0 2376.3 26.7 3168.4 35.6 3960.5 44.5 53.0 25
203 IHD040203 77.0 2344.7 30.5 3126.2 40.6 3907.8 50.8 61.0 25
254 IHD040254 61.0 2324.1 38.1 3098.8 50.8 3873.5 63.5 76.0 25
305 IHD040305 51.0 2333.3 45.8 3111.0 61.0 3888.8 76.3 91.0 25
64 IHD050064 413.0 3964.8 9.6 5286.4 12.8 6608.0 16.0 19.0 25
76 IHD050076 339.0 3864.6 11.4 5152.8 15.2 6441.0 19.0 23.0 25
89 IHD050089 288.0 3844.8 13.4 5126.4 17.8 6408.0 22.3 27.0 25
102 IHD050102 245.0 3748.5 15.3 4998.0 20.4 6247.5 25.5 31.0 25
115 IHD050115 215.0 3708.8 17.3 4945.0 23.0 6181.3 28.8 35.0 25
50 25 127 IHD050127 192.0 3657.6 19.1 4876.8 25.4 6096.0 31.8 38.0 25
(2") (1") 139 IHD050139 168.0 3502.8 20.9 4670.4 27.8 5838.0 34.8 42.0 25
152 IHD050152 154.0 3511.2 22.8 4681.6 30.4 5852.0 38.0 46.0 25
178 IHD050178 134.0 3577.8 26.7 4770.4 35.6 5963.0 44.5 53.0 25
203 IHD050203 117.0 3562.7 30.5 4750.2 40.6 5937.8 50.8 61.0 10
254 IHD050254 89.0 3390.9 38.1 4521.2 50.8 5651.5 63.5 76.0 10
305 IHD050305 73.0 3339.8 45.8 4453.0 61.0 5566.3 76.3 91.0 10
*Tabulated deflections values shwon represent compressed lengths near solid and are for design information only.
17
KG X 2.20463= LBS.
EXTRA HEAVY DUTY DIE SPRINGS METRIC ISO SPECIFICATION SERIES YELLOW
Hole Rod Free Load
PART (15% of free length) (17% of free length) (20% of free length)
(mm) (mm) (mm) Def. Deflection Box
Load (N) Deflection Load (N) Deflection Load (N) Deflection
(N) mm mm mm
A B C
25 IXD010025 36.8 138.0 3.8 156.4 4.3 184.0 5.0 6.2 200
32 IXD010032 27.9 133.9 4.8 151.8 5.4 178.6 6.4 8.0 200
38 IXD010038 23.7 135.1 5.7 153.1 6.5 180.1 7.6 9.5 100
10 5 44 IXD010044 19.2 126.7 6.6 143.6 7.5 169.0 8.8 11.0 100
(3/8") (3/16") 51 IXD010051 16.5 126.2 7.7 143.1 8.7 168.3 10.2 13.0 100
64 IXD010064 13.2 126.7 9.6 143.6 10.9 169.0 12.8 16.0 100
76 IXD010076 10.9 124.3 11.4 140.8 12.9 165.7 15.2 19.0 100
305 IXD010305 2.6 119.0 45.8 134.8 51.9 158.6 61.0 76.0 50
25 IXD012025 58.5 219.4 3.8 248.6 4.3 292.5 5.0 6.2 100
32 IXD012032 43.9 210.7 4.8 238.8 5.4 281.0 6.4 8.0 100
38 IXD012038 36.0 205.2 5.7 232.6 6.5 273.6 7.6 9.5 100
44 IXD012044 30.3 200.0 6.6 226.6 7.5 266.6 8.8 11.0 100
12.5 6.3 IXD012051
51 26.2 200.4 7.7 227.2 8.7 267.2 10.2 13.0 100
(1/2") (9/32") IXD012064
64 21.2 203.5 9.6 230.7 10.9 271.4 12.8 16.0 50
76 IXD012076 17.1 194.9 11.4 220.9 12.9 259.9 15.2 19.0 50
89 IXD012089 14.5 193.6 13.4 219.4 15.1 258.1 17.8 22.0 50
305 IXD012305 4.3 196.7 45.8 223.0 51.9 262.3 61.0 76.0 50
25 IXD016025 118.0 442.5 3.8 501.5 4.3 590.0 5.0 6.2 100
32 IXD016032 89.0 427.2 4.8 484.2 5.4 569.6 6.4 8.0 50
38 IXD016038 72.1 411.0 5.7 465.8 6.5 548.0 7.6 9.5 50
44 IXD016044 60.9 401.9 6.6 455.5 7.5 535.9 8.8 11.0 50
16 8 51 IXD016051 52.3 400.1 7.7 453.4 8.7 533.5 10.2 13.0 50
(5/8") (11/32") 64 IXD016064 41.2 395.5 9.6 448.3 10.9 527.4 12.8 16.0 50
76 IXD016076 34.1 388.7 11.4 440.6 12.9 518.3 15.2 19.0 50
89 IXD016089 29.5 393.8 13.4 446.3 15.1 525.1 17.8 22.0 50
102 IXD016102 25.6 391.7 15.3 443.9 17.3 522.2 20.4 26.0 50
305 IHD016305 8.4 384.3 45.8 435.5 51.9 512.4 61.0 76.0 50
25 IXD020025 293.0 1098.8 3.8 1245.3 4.3 1465.0 5.0 6.2 50
32 IXD020032 224.0 1075.2 4.8 1218.6 5.4 1433.6 6.4 8.0 50
38 IXD020038 177.0 1008.9 5.7 1143.4 6.5 1345.2 7.6 9.5 50
44 IXD020044 149.0 983.4 6.6 1114.5 7.5 1311.2 8.8 11.0 50
51 IXD020051 128.0 979.2 7.7 1109.8 8.7 1305.6 10.2 13.0 50
64 IXD020064 99.0 950.4 9.6 1077.1 10.9 1267.2 12.8 16.0 50
20 10 76 IXD020076 81.7 931.4 11.4 1055.6 12.9 1241.8 15.2 19.0 50
(3/4") (3/8") 89 IXD020089 69.5 927.8 13.4 1051.5 15.1 1237.1 17.8 22.0 50
102 IXD020102 60.6 927.2 15.3 1050.8 17.3 1236.2 20.4 26.0 50
115 IXD020115 53.0 914.3 17.3 1036.2 19.6 1219.0 23.0 29.0 50
127 IXD020127 47.5 904.9 19.1 1025.5 21.6 1206.5 25.4 32.0 50
139 IXD020139 43.0 896.6 20.9 1016.1 23.6 1195.4 27.8 35.0 50
152 IXD020152 39.0 889.2 22.8 1007.8 25.8 1185.6 30.4 8.0 50
305 IXD020305 21.2 969.9 45.8 1099.2 51.9 1293.2 61.0 76.0 50
32 IXD025032 374.4 1797.1 4.8 2036.7 5.4 2396.2 6.4 8.0 50
38 IXD025038 346.0 1972.2 5.7 2235.2 6.5 2629.6 7.6 9.5 50
44 IXD025044 244.0 1610.4 6.6 1825.1 7.5 2147.2 8.8 11.0 50
25 12.5 IXD025051
51 207.5 1587.4 7.7 1799.0 8.7 2116.5 10.2 13.0 50
(1") (1/2") IXD025064
64 161.0 1545.6 9.6 1751.7 10.9 2060.8 12.8 16.0 50
76 IXD025076 130.8 1491.1 11.4 1689.9 12.9 1988.2 15.2 19.0 25
89 IXD025089 110.5 1475.2 13.4 1671.9 15.1 1966.9 17.8 22.0 25
* Tabulated deflections values shown represent compressed lengths near solid and are for design information only.
18
KG X 2.20463= LBS.
EXTRA HEAVY DUTY DIE SPRINGS METRIC ISO SPECIFICATION SERIES YELLOW
Hole Rod Free Load
Dia. Dia. Length For Long Life For Long Life *Maximum Operating Def.
at (15% of free length) (17% of free length)
PART 1mm
(20% of free length)
(mm) (mm) (mm) NUMBER Maximum Number
Def. Load (N) Deflection Load (N) Deflection Load (N) Deflection Deflection Box
(N) mm mm mm
A B C
102 IXD025102 96.3 1473.4 15.3 1669.8 17.3 1964.5 20.4 26.0 25
115 IXD025115 85.7 1478.3 17.3 1675.4 19.6 1971.1 23.0 29.0 25
127 IXD025127 76.3 1453.5 19.1 1647.3 21.6 1938.0 25.4 32.0 25
25 12.5
152 IXD025152 63.5 1447.8 22.8 1640.8 25.8 1930.4 30.4 38.0 25
(1") (1/2")
178 IXD025178 53.9 1439.1 26.7 1631.0 30.3 1918.8 35.6 44.0 25
203 IXD025203 47.0 1431.2 30.5 1622.0 34.5 1908.2 40.6 51.0 25
305 IXD025305 30.9 1413.7 45.8 1602.2 51.9 1884.9 61.0 76.0 25
38 IXD032038 528.2 3010.7 5.7 3412.2 6.5 4014.3 7.6 9.5 50
44 IXD032044 424.4 2801.0 6.6 3174.5 7.5 3734.7 8.8 11.0 25
51 IXD032051 353.0 2700.5 7.7 3060.5 8.7 3600.6 10.2 13.0 25
64 IXD032064 269.2 2584.3 9.6 2928.9 10.9 3445.8 12.8 16.0 25
76 IXD032076 218.5 2490.9 11.4 2823.0 12.9 3321.2 15.2 19.0 25
89 IXD032089 180.3 2407.0 13.4 2727.9 15.1 3209.3 17.8 22.0 25
32 16 102 IXD032102 155.0 2371.5 15.3 2687.7 17.3 3162.0 20.4 26.0 25
(1 1/4") (5/8") 115 IXD032115 140.0 2415.0 17.3 2737.0 19.6 3220.0 23.0 29.0 25
127 IXD032127 124.0 2362.2 19.1 2677.2 21.6 3149.6 25.4 32.0 25
152 IXD032152 102.0 2325.6 22.8 2635.7 25.8 3100.8 30.4 38.0 25
178 IXD032178 88.2 2354.9 26.7 2668.9 30.3 3139.9 35.6 44.0 25
203 IXD032203 76.0 2314.2 30.5 2622.8 34.5 3085.6 40.6 51.0 25
254 IXD032254 60.8 2316.5 38.1 2625.3 43.2 3088.6 50.8 64.0 25
305 IXD032305 49.0 2241.8 45.8 2540.7 51.9 2989.0 61.0 76.0 25
51 IXD040051 628.0 4804.2 7.7 5444.8 8.7 6405.6 10.2 13.0 25
64 IXD040064 487.0 4675.2 9.6 5298.6 10.9 6233.6 12.8 16.0 25
76 IXD040076 379.0 4320.6 11.4 4896.7 12.9 5760.8 15.2 19.0 25
89 IXD040089 321.0 4285.4 13.4 4856.7 15.1 5713.8 17.8 22.0 25
102 IXD040102 281.0 4299.3 15.3 4872.5 17.3 5732.4 20.4 26.0 25
40 20
115 IXD040115 245.0 4226.3 17.3 4789.8 19.6 5635.0 23.0 29.0 25
(1 1/2") (3/4")
127 IXD040127 221.0 4210.1 19.1 4771.4 21.6 5613.4 25.4 32.0 25
152 IXD040152 168.0 3830.4 22.8 4341.1 25.8 5107.2 30.4 38.0 25
203 IXD040203 132.0 4019.4 30.5 4555.3 34.5 5359.2 40.6 51.0 25
254 IXD040254 107.0 4076.7 38.1 4620.3 43.2 5435.6 50.8 64.0 25
305 IXD040305 87.8 4016.9 45.8 4552.4 51.9 5355.8 61.0 76.0 25
64 IXD050064 709.0 6806.4 9.6 7713.9 10.9 9075.2 12.8 16.0 25
76 IXD050076 572.0 6520.8 11.4 7390.2 12.9 8694.4 15.2 19.0 25
89 IXD050089 475.0 6341.3 13.4 7186.8 15.1 8455.0 17.8 22.0 25
102 IXD050102 405.0 6196.5 15.3 7022.7 17.3 8262.0 20.4 26.0 25
50 25 115 IXD050115 352.0 6072.0 17.3 6881.6 19.6 8096.0 23.0 29.0 25
(2") (1") 127 IXD050127 316.0 6019.8 19.1 6822.4 21.6 8026.4 25.4 32.0 25
152 IXD050152 239.0 5449.2 22.8 6175.8 25.8 7265.6 30.4 38.0 25
203 IXD050203 187.0 5694.2 30.5 6453.4 34.5 7592.2 40.6 51.0 10
254 IXD050254 153.0 5829.3 38.1 6606.5 43.2 7772.4 50.8 64.0 10
305 IXD050305 127.0 5810.3 45.8 6585.0 51.9 7747.0 61.0 76.0 10
* Tabulated deflections values shown represent compressed lengths near solid and are for design information only.
19
Tube
SPRING CAGES
O.D.
Pocket
Dia. H Approx.
.49
Length
SPRING POCKET TU B E H
O.D. DIA. O.D. DIA.
3/4 29/32 .855 7/16
1 1-5/32 1.105 9/16
1-1/4 1-13/32 1.355 3/4
1-1/2 1-21/32 1.605 31/32
2 2-5/32 2.105 1-3/8
3/4 1" 1-1/4" 1-1/2" 2"

SPRING SPRING SPRING SPRING SPRING
Part # Length Part # Length Part # Length Part # Length Part # Length Spring cages
LSC0608 1.00 LSC0808 1.00 LSC1008 1.00 LSC1208 1.00 LSC1608 1.00
are a natural
addition to
LSC0614 1.75 LSC0814 1.75 LSC1014 1.75 LSC1214 1.75 LSC1614 1.75 the Lamina
LSC0616 2.00 LSC0816 2.00 LSC1016 2.00 LSC1216 2.00 LSC1616 2.00 spring
collection.
They are in
LSC0626 3.25 LSC0826 3.25 LSC1026 3.25 LSC1226 3.25 LSC1626 3.25 stock and
LSC0628 3.50 LSC0828 3.50 LSC1028 3.50 LSC1228 3.50 LSC1628 3.50 ready to ship.
LSC1688 11.00
LSC1696 12.00
20
UTILITY SPRINGS MM x .039837 = INCHES
KG X 2.20463= LBS.
ROUND WIRE DIE FIXTURE SPRINGS

10 & 18 INCH LENGTHS PLAIN ENDS
MUSIC WIRE 10" LENGTHS CARBON STEEL 18" LENGTHS
Pounds Pounds
Max. Coils No. Max. Coils No.
O.D. Part Wire Per Inch O.D. Part Wire Per Inch
Rod Per Per Rod. Per Per
Inches No. Dia. of Comp- Inches No. Dia. of Comp-
Dia. Inch Box Dia. Inch Box
ression ression
.087 RW-1 .062 .010 28 .135 12 .479 RW-9 .355 .041 4.5 .6 12
.089 RW-1A .062 .014 28.5 .6 12 .493 RW-9A .355 .054 4 2.1 12
.116 RW-2 .092 .012 25 .11 12 .520 RW-9B .355 .062 5.75 2.0 12
.120 RW-2A .078 .016 25 .4 12 .532 RW-9C .355 .072 4 5.25 12
.176 RW-3 .141 .014 14 .1 12 .612 RW-10 .500 .054 3 1.31 12
.180 RW-3A .141 .018 14 .3 12 .678 RW-10A .531 .062 3 1.9 12
.180 RW-3B .125 .026 13 1.95 12 .676 RW-10B .531 .072 3.25 3.25 12
.178 RW-3C .094 .035 19 5.6 12 .675 RW-10C .531 .068 3.5 2.5 12
.240 RW-4 .188 .018 9.5 .31 12 .805 RW-11 .672 .062 2.5 1.3 12
.238 RW-4A .188 .022 11 .26 12 .805 RW-11A .625 .080 2.5 3.5 12
.241 RW-4B .188 .026 9.5 .78 12 .865 RW-11B .656 .098 2.25 8.0 12
.248 RW-4C .171 .031 10 1.6 12 .922 RW-11C .640 .125 2.75 15.0 12
.242 RW-4D .171 .035 13 2.3 12 .921 RW-12A .750 .080 2.5 2.1 12
.238 RW-4E .141 .041 9 6.25 12 .975 RW-12B .781 .098 2 5.75 6
.243 RW-4F .141 .047 10 11.0 12 1.020 RW-13 .844 .085 2.25 2.1 6
.302 RW-5 .250 .022 10 .175 12 1.020 RW-12C .750 .125 2 13.5 6
.304 RW-5A .234 .031 11 .65 12 1.100 RW-12 .828 .125 2.75 7.75 6
.304 RW-5B .219 .037 11 1.5 12 1.055 RW-12D .765 .135 3 11.0 6
.303 RW-5C .219 .041 8 3.25 12 1.145 RW-13A .890 .125 2 9.0 6
.305 RW-5D .203 .047 7.5 6.5 12 1.145 RW-14 .953 .090 1.75 2.5 6
.302 RW-5E .185 .055 8 12.5 12 1.343 RW-14A 1.031 .148 1.75 14.0 6
.366 RW-6 .304 .031 11 .57 12 1.591 RW-15 1.281 .148 1.5 8.75 6
.361 RW-6A .281 .035 10 .675 12 1.820 RW-16 1.500 .148 1.75 5.0 6
.365 RW-6B .266 .043 7 2.15 12
.368 RW-6C .266 .047 8.5 2.8 12 Compression Spring Assortment
.365 RW-6D .250 .055 6 8.2 12
.365 RW-6E .234 .062 6.5 13.0 12 111-850 (R50)
.368 RW-6F .203 .075 7 28.0 12
.426 RW-7 .344 .035 7 .55 12 ASSORTMENT CONSISTS OF
.425 RW-7A .328 .047 7 2.0 12 1 EACH OF THE 18 LONG
.425 RW-7B .297 .055 6 4.7 12 SPRINGS
.427 RW-7C .281 .062 6.5 7.4 12
.429 RW-7D .266 .075 5.5 20.0 12
.430 *RW-7E .250 .085 6 35.0 12
.488 RW-8 .406 .035 9 .28 12
.488 RW-8A .391 .047 7.5 1.2 12
.495 RW-8B .375 .055 7 2.5 12
.492 RW-8C .360 .062 4 7.4 12
.490 RW-8D .325 .075 4.5 15.0 12
.495 *RW-8E .310 .091 5 33.0 12
.500 *RW-8F .270 .115 5.5 95.0 12 FORMULA TO CALCULATE LBS. PER INCH
FOR ALL ALTERED SPRINGS
*Indicates carbon steel; All other items music wire
COMPRESSION AXB
11-845 (R-45) SPRING =D
C
ASSORTMENT A = Catalog Free Length
CONSISTS OF
2 EACH OF
B = Rate in lbs. Per Inch, Per A
ABOVE 10 C = Reqd Cut Free Length
LONG SPRINGS D = Lbs. Per Inch of Reqd Free Length
Specials Quoted Upon Request 21

UTILITY SPRINGS ST
OC
K
IN
COMPRESSION SPRINGS STEEL FIXTURE
INCHES X 25.4 = mm LBS. X .454 = KG
O.D. MAX. Length Part Wire Comp. Rate Per Total Type of N o . P er
Inches Rod Dia. Inches Number Dia. Inch Lbs. Coils E nds B o x.
.078 .047 .53 020-074 (G-74) .012 4.87 17 Plain 12
.078 .047 .56 020-073 (G-73) .011 3.87 18 Plain 12
.108 .062 .81 020-076 (G-76) .018 12.50 16 Plain 12
.110 .062 .91 020-075 (G-75) .018 9.25 22 Plain 12
.120 .078 .62 020-0125 (G-125) .016 6.60 13 Squared 25
.120 .075 .75 020-126 (G-126) .016 5.30 18 Squared 25
.170 .141 .21 020-077 (G-77) .012 .75 7 Plain 12
.178 .141 10.00 020-056 (G-56) .014 .03 138 Plain 12
.180 .125 .75 020-127 (G-127) .022 8.60 11 Squared 25
.180 .125 1.00 020-128 (G-128) .022 6.80 14 Squared 25
.180 .125 1.12 020-129 .022 6.00 15 Squared 25
.180 .125 1.25 020-130 .022 5.30 17 Squared 25
.185 .156 .93 020-084 (G-84) .012 .03 19 Plain 12
.240 .188 10.00 020-055 (G-55) .022 .25 112 Plain 12
.240 .172 1.00 020-131 .026 7.80 11 Squared 25
.240 .172 1.25 020-132 .026 6.10 14 Squared 25
.240 .172 1.50 020-133 .026 5.10 15 Squared 25
.280 .188 1.25 020-080 (G-80) .040 18.00 15 Plain 12
.281 .234 2.06 020-098 (G-98) .020 .25 5 Squared 12
.282 .188 1.31 020-079 (G-79) .040 17.00 13 Plain 12
.300 .250 10.00 020-054 (G-54) .022 .03 101 Squared 12
.313 .250 .87 020-085 (G-85) .0254 Ph. Bronz e 2.25 7 Squared 12
.315 .266 1.96 020-081 (G-81) .022 .56 23.5 Squared 12
.315 .250 2.43 020-083 (G-83) .0285 Brass .87 23 Squared 12
.325 .250 2.43 020-082 (G-82) .032 Brass 1.31 23 Squared 12
.340 .250 2.50 107-103 (WA-103) .042 8.00 24 Sq. & Gr. 12
.345 .250 1.00 107-100 (WA-100) .042 20.00 10.5 Sq. & Gr. 12
.345 .250 1.50 107-101 (WA-101) .042 14.00 15 Sq. & Gr. 12
.345 .250 2.00 107-102 (WA-102) .042 12.00 19.5 Sq. & Gr. 12
.350 .250 3.00 107-104 (WA-104) .042 6.00 29 Sq. & Gr. 12
.360 .281 1.50 020-134 .035 7.30 10 Squared 25
.360 .281 1.75 020-135 .035 6.20 11 Squared 25
.360 .281 2.00 020-136 .035 5.40 13 Squared 25
.360 .250 12.00 020-053 (G-53) .0475 2.25 92 Plain 12
.369 .281 .78 020-086 (G-86) .042 Brass 7.37 9 Sq. & Gr 12
.375 .266 11.50 020-052 (G-52) .0475 2.25 88 Plain 12
.380 .250 2.12 020-094 (G-94) .063 42.00 18.5 Sq. & Gr 12
.385 .281 2.03 020-088 (G-88) .0475 11.00 19 Sq. & Gr 12
.440 .328 2.00 020-093 (G-93) .054 13.00 17 Squared 12
.440 .344 2.56 020-071 (G-71) .041 2.62 26 Squared 12
.440 .328 2.62 020-089 (G-89) .0475 6.00 20 Sq. & Gr 12
.460 .328 2.00 107-107 (WA-107) .062 32.00 14.5 Sq. & Gr 12
.465 .344 2.50 020-090 (G-90) .054 12.00 17 Sq. & Gr 12
.465 .328 1.50 107-106 (WA-106) .062 42.00 11 Sq. & Gr 12
.465 .328 2.50 107-108 (WA-108) .062 25.00 17 Sq. & Gr 12
.465 .328 3.00 107-109 (WA-109) .062 24.00 20 Sq. & Gr 12
.470 .328 1.00 107-105 (WA-105) .062 58.00 8 Sq. & Gr 12
.473 .344 3.50 107-110 (WA-110) .062 18.00 24 Sq. & Gr 12
.495 .360 2.50 020-091 (G-91) .0625 18.00 16 Sq. & Gr 12
.500 .344 .96 020-060 (G-60) .072 Ph. Brass 52.00 6.5 Sq. & Gr 12
.505 .406 2.06 020-092 (G-92) .048 5.50 16 Squared 12
.518 .375 12.00 020-051 (G-51) .0625 2.75 73 Plain 12
.532 .313 1.03 020-059 (G-59) .1055 210.00 7 Sq. & Gr 12
.575 .484 2.15 020-069 (G-69) .041 3.12 8.5 Squared 12
22 Specials Quoted Upon Request

UTILITY SPRINGS ST
OC
K
IN
COMPRESSION SPRINGS STEEL FIXTURE
INCHES X 25.4 = mm LBS. X .454 = KG
O.D. Max Length Part Wire Comp. Rate Per Total Type of N o . P er
Inches Rod Dia. Inches Number Dia. Inch Lbs. Coils E nds B o x.
.581 .438 1.00 107-111 (WA-111) .072 74.00 6 Sq. & Gr. 12
.585 .438 3.00 107-115 (WA-115) .072 20.00 15 Sq. & Gr. 12
.588 .438 2.50 107-114 (WA-114) .072 26.00 13 Sq. & Gr. 12
.590 .438 4.00 107-117 (WA-117) .072 16.00 19.5 Sq. & Gr. 12
.594 .438 1.50 107-112 (WA-112) .072 34.00 8 Sq. & Gr. 12
.594 .438 2.00 107-113 (WA-113) .072 32.00 11.25 Sq. & Gr. 12
.600 .438 3.50 107-116 (WA-116) .072 18.00 17.5 Sq. & Gr. 12
.615 .438 2.84 020-068 (G-68) .080 30.00 13.5 Sq. & Gr. 12
.620 .500 11.50 020-050 (G-50) .054 1.00 60 Plain 6
.690 .469 4.06 020-067 (G-67) .1055 58.00 18.5 Sq. & Gr. 12
.735 .563 12.00 020-049 (G-49) .080 3.80 55 Plain 3
.755 .532 2.60 020-072 (G-72) .1055 66.40 11 Sq. & Gr. 12
.850 .688 1.09 020-070 (G-70) .080 Brass 22.00 4.5 Sq. & Gr. 12
.860 .578 2.59 020-066 (G-66) .135 154.00 10 Sq. & Gr. 12
.870 .672 3.06 020-064 (G-64) .0915 21.80 12 Sq. & Gr. 12
.870 .640 12.00 020-047 (G-47) .1055 8.00 48 Plain 3
.875 .625 2.03 020-065 (G-65) .1205 110.00 8 Sq. & Gr. 12
.875 .703 10.00 020-048 (G-48) .080 3.25 36 Plain 3
.920 .750 2.03 020-063 (G-63) .080 16.00 8 Sq. & Gr. 12
1.000 .750 2.56 020-062 (G-62) .1205 56.00 9.5 Sq. & Gr. 12
.28x.16 .125 .50 020-078 (G-78) .013 .87 8 Squared 12
.53x.28 .125 .90 020-087 (G-87) .072 Ph. Bronz e 56.00 6 Squared 12
.53x1.03x.86 .421 3.50 020-061 (G-61) .051 1.20 13 Sq. & Gr. 12
.62x.75 .453 1.00 020-058 (G-58) .080 Brass 31.00 5.5 Sq. & Gr. 12
.66x.94 .531 .93 020-057 (G-57) .057 Ph. Bronz e 6.00 5 Squared 12
Order by part number
EXTENSION SPRINGS STEEL FIXTURE

Approx. Max.
O.D. Length Part Wire Initial Rate Max. Safe Types of N o.
Inches Inches Number Diameter Coils Tension Lbs./Inch Ext. L o ad E nds P er
L b s. L b s.
B ox
.120 .62 020-137 .016 27 .06 3.70 .641 2.04 Full loops 25
.120 .75 020-138 .016 34 .31 2.50 .714 2.07 Full loops 25
.120 .88 020-139 .016 44 .19 2.20 .990 2.07 Full loops 25
.156 2.06 020-035 (G-35) .020 Brass 90 .25 .50 1.180 1.75 Full loops 12
.156 6.62 020-011 (G-11) .0258 232 1.50 .81 4.000 6.75 Full loops 12
.172 9.06 020-008 (G-8) .0256 302 1.50 1.00 5.500 7.50 Full loops 12
.180 1.00 020-140 .022 32 .19 2.8 1.238 3.50 Full loops 25
.180 1.12 020-141 .022 36 .31 2.4 1.344 3.50 Full loops 25
.180 1.25 020-142 .022 42 .04 2.2 1.700 3.50 Full loops 25
.187 1.00 020-042 (G-42) .014 70 .12 .18 4.000 .87 Plain ends 12
.234 1.12 020-040 (G-40) .020 34 .50 .75 2.380 2.25 Full loops 12
.240 1.37 020-143 .026 39 .06 1.8 2.450 4.27 Full loops 25
.240 1.50 020-144 .026 42 .22 1.60 2.540 4.27 Full loops 25
.240 1.75 020-145 .026 53 .25 1.37 3.177 4.27 Full loops 25
.250 4.00 020-020 (G-20) .0286 118 .25 .81 1.500 4.00 Full loops 12
EXTENSION SPRING ASSORTMENT

020-835 R-35
(2) G-5 (2) G-9 (2) G-12 (2) G-8 (2) G-18
(2) G-7 (2) G-10 (2) G-22 (2) G-27 (2) G-17
(2) G-11 (2) G-28 (2) G-14 (2) G-15 (2) G-37
23
UTILITY SPRINGS
EXTENSION SPRINGS STEEL FIXTURE
Approx. Max.
O.D. Length Part Wire Initial
Rate
Max. Safe Types of N o.
Coils Per Inch P er
Inches Inches Number Diameter Tension Ext. L o ad E nds
L b s.
L b s.
L b s.
B ox
.250 5.34 020-018 (G-18) .041 118 5.50 5.00 3.000 17.00 Full loops 12
.250 5.75 020-017 (G-17) .0286 181 .62 .44 2.250 4.50 Full loops 12
.265 6.12 020-016 (G-16) .0348 153 1.75 1.10 5.500 9.25 Full loops, side 12
.296 1.12 020-039 (G-39) .040Brass 14.5 .50 3.80 .310 5.00 Dbl. loops 12
.296 5.75 020-015 (G-15) .0475 108 2.00 3.60 3.500 17.00 Full loops, side 12
.312 5.00 020-026 (G-26) .041 106 .75 1.60 4.950 11.25 Full loops 12
.328 6.50 020-010 (G-10) .0348 162 1.25 .50 9.000 6.25 Dbl. loops, side 12
.343 1.44 020-037 (G-37) .0475 17 4.37 15.00 .375 17.50 Full loops 12
.343 5.37 020-027 (G-27) .0475 103 1.12 2.60 3.620 24.00 Full loops 12
.343 8.12 020-007 (G-7) .0475 158 2.18 1.60 7.500 16.25 Full loops 12
.359 10.00 020-005 (G-5) .054 193.5 1.50 2.30 8.000 20.00 Full loops 12
.360 1.50 020-146 .037 25 .19 3.40 2.385 7.80 Full loops 25
.360 1.75 020-147 .037 29 .38 2.60 2.700 7.83 Full loops 25
.360 2.00 020-148 .037 36 .56 2.20 3.268 7.80 Full loops 25
.370 3.25 020-019 (G-19) .041 66 1.50 1.90 4.000 8.00 Half loops 12
.370 5.50 020-014 (G-14) .054 90 2.00 4.00 3.250 15.50 Full loops 12
.370 10.00 020-006 (G-6) .0475 193.5 2.00 1.10 8.500 11.50 Full loops 12
.440 5.25 020-028 (G-28) .0625 74 3.00 6.50 4.000 58.00 Full loops 12
.440 6.44 020-009 (G-9) .048 118.5 2.00 1.10 7.500 10.50 Dbl. loops 12
.480 4.50 020-022 (G-22) .0625 57.5 1.00 6.20 3.000 17.00 Full loops 12
.500 1.62 020-034 (G-34) .080 11 28.00 64.00 .620 67.00 Half loops 12
.500 10.00 020-004 (G-4) .0625 144 4.50 1.87 8.500 20.50 Full loops 12
.530 5.25 020-025 (G-25) .0625 49 3.75 5.00 4.000 21.75 Sw iv. loops 12
.550 5.62 020-012 (G-12) .080 58.5 4.00 10.00 2.620 31.00 Full loops 12
.560 5.50 020-013 (G-13) .080 55 9.00 10.50 2.940 38.00 Half loops 12
.620 10.00 020-003 (G-3) .072 118.5 2.44 2.10 9.500 21.50 Full loops 6
.680 4.00 *020-099 (G-99) .1055 30.5 9.00 34.00 1.530 58.00 Half loops 6
.720 2.00 020-095 (G-95) .105 9 11.00 80.00 .530 57.00 Full loops 12
.720 4.00 020-024 (G-24) .1055 26 24.00 12.50 2.120 82.00 Half loops 12
.740 4.06 020-023 (G-23) .0625 45 1.50 1.40 6.500 12.00 Full loops 12
.750 2.59 020-032 (G-32) .1055 13 12.25 46.00 .810 44.00 Full loops 12
.750 2.66 020-033 (G-33) .080 18.5 2.25 10.30 4.000 47.00 Full loops 12
.810 10.00 020-002 (G-2) .072 119 4.12 .75 21.000 23.12 Full loops 3
.870 6.00 *020-029 (G-29) .1205 38.5 8.00 18.50 2.380 68.20 Half loops 6
.870 10.00 020-001 (G-1) .0915 94 4.38 2.50 11.000 30.50 Full loops 3
1.000 8.50 020-031 (G-31) .1055 65 9.00 6.00 8.500 41.00 Half loops 3
1.060 8.00 *020-030 (G-30) .135 49 13.00 24.00 5.000 45.00 Half loops 6
1.120 10.00 *020-100 (G-100) .148 59 8.00 14.00 6.000 95.00 Half loops 6
1.250 12.00 *020-101 (G-101) .162 65 31.00 15.00 7.400 112.00 Half loops 6
1.370 14.00 *020-102 (G-102) .177 70 14.00 14.00 8.750 130.00 Half loops 6
1.560 16.00 *020-103 (G-103) .207 70 32.00 16.00 9.000 175.00 Half loops 6
1.250 7.62 020-104 .207 26 61.00 94.00 2.468 281.82 Full loops 2
1.812 8.19 020-105 .250 22 61.00 68.00 4.189 341.56 Full loops 2
.297 16.00 020-152 .041 15.30 2.94 .69 14.583 12.43 Full loops 12
.344 16.00 020-153 .048 15.125 3.19 1.06 14.445 16.72 Full loops 12
.375 16.00 020-154 .054 15.310 3.50 1.50 13.724 21.45 Full loops 12
.422 16.00 020-155 .063 15.150 5.00 2.25 11.903 29.58 Full loops 12
.438 16.00 020-156 .072 15.375 4.08 3.90 9.950 40.97 Full loops 12
MACHINERY BRAKE & SHEAR SPRINGS
* The following part numbers identify certain standard springs described in the table above that are of oil-tempered carbon steel
and specially suited to heavy duty-extension spring use.
G - 29 G - 30 G - 99 G - 100 G - 101 G - 102 G - 103 These are flagged with an asterisk to simplify finding them.
Specials Quoted Upon Request
24
Engineered for durability
these quality springs have
UTILITY SPRINGS
unlimited applications for
Heavy duty Length 17-1/2
general utility and Industry.
2-drawer case Width 12-1/4
numbered dividers Height 5-7/8
Abbreviations: Display ready Shipping Weight 57
ext., extension 41 different nos lbs.
comp., compression 310 comp. & ext. spgs
GENERAL MAINTENANCE ASSORTMENT #020-819-1

Part Type Length in O.D. Wire L b s. Approx. Load Ass't Unit
Number Inches Inches Siz e Rate/Inch @ Reference Extension Qty. P ack
020-042 Ext. 1.000 .188 .014 3. o z . 30. o z . @ 1.500 12 12
020-040 Ext. 1.125 .234 .020 12. o z . 9. o z @ 1.625 6 12
020-039 Ext. 1.125 .297 .040 Brass 3.8 1.6 lbs. @ .875 12 12
020-037 Ext. 1.438 .344 .048 15.0 10.0 lbs. @ .375 12 12
020-034 Ext. 1.625 .500 .080 64.0 23.0 lbs. @ 1.250 6 12
020-032 Ext. 2.594 .750 .105 46.0 29.5 lbs. @ 2.375 6 12
020-033 Ext. 1.656 .750 .080 10.3 12.5 lbs. @ 3.968 6 12
020-019 Ext. 3.250 .375 .041 1.9 5.2 lbs. @ 5.250 12 12
020-020 Ext. 4.000 .250 .028 13. o z . 1.9 lbs. @ 6.000 12 12
020-024 Ext. 4.000 .719 .105 12.5 36.5 lbs. @ 5.000 6 12
020-023 Ext. 4.062 .734 .063 1.4 4.3 lbs. @ 6.062 6 12
020-022 Ext. 4.500 .484 .063 6.3 14.0 lbs. @ 6.500 6 12
020-025 Ext. 5.250 .531 .062 8.5 8.5 lbs. @ 6.250 6 12
020-012 Ext. 5.625 .547 .080 10.0 24.0 lbs. @ 7.625 6 12
020-017 Ext. 5.750 .250 .028 7. o z . 1.6 lbs. @ 7.750 12 12
020-009 Ext. 6.438 .438 .048 1.1 4.2 lbs. @ 8.437 10 12
020-010 Ext. 6.500 .328 .035 7.5 2.2 lbs. @ 8.500 12 12
020-031 Ext. 8.500 1.000 .105 6.00 16.75 lbs. @ 10.250 2 3
020-004 Ext. 10.000 .500 .062 1.8 10.2 lbs. @ 13.000 8 12
020-003 Ext. 10.000 .625 .072 2.1 8.8 lbs. @ 13.000 6 12
020-002 Ext. 10.000 .812 .072 12. o z . 5.6 lbs. @ 12.000 4 3
Part Type Length in O.D. Wire Siz e L b s . Ap prox. Ass't Unit
Number Inches Inches Rate/Inch Solid Ext. Qty P ack
020-078 Tap.Comp. .500 .281x.156 .013 14. o z . .117 12 12
020-086 Comp. .781 .375 .042 Brass 7.4 oz . .378 6 12
020-084 Comp. .938 .188 .012 5. o z . .240 6 12
020-060 Comp. .969 .500 .072 52.0 .612 6 12
020-059 Comp. 1.031 .531 .105 21.0 .950 6 12
020-080 Comp. 1.250 .281 .040 18.0 .640 12 12
020-081 Comp. 1.969 .312 .022 9. o z .528 12 12
020-065 Comp. 2.000 .875 .120 110.0 .964 6 12
020-063 Comp. 2.031 .938 .080 16.0 .640 6 12
020-069 Comp. 2.193 .590 .040 3.1 .380 6 12
020-091 Comp. 2.500 .500 .063 18.0 1.000 10 12
020-062 Comp. 2.562 1.015 .120 56.00 1.148 6 12
020-089 Comp. 2.625 .438 .048 6.0 .950 10 12
020-068 Comp. 2.844 .625 .080 30.0 1.080 6 12
020-064 Comp. 3.062 .875 .092 21.5 1.098 4 12
020-067 Comp. 4.062 .688 1.05 58.0 1.952 6 12
020-056 Comp. 10.000 .176 .014 .5 oz . 2.254 6 12
020-048 Comp. 10.000 .875 .080 3.2 3.000 4 12
020-052 Comp. 11.500 .375 .047 2.3 4.240 6 12
020-050 Comp. 11.500 .625 .054 1.0 3.564 6 12
25
This is the baby of our general maintenance assortment. So when a larger stock
of springs are not needed, have our midget asst in its enameled steel case ready
in each department for quick application. Kit contains 105 of 18 different
extension & compression springs.
105 MIDGET SPRINGS ASSORTMENT NO. 020-081

Approx. Rate Max. N o.
O.D. Length Part Wire Coils Max. Type of Asst.
Initial P er Safe P er
Inches Inches Number Diameter Ext. E nds Qty.
Tension Lbs. Inch Lbs. L o ad L b s. B ox
.187 1.00 020-042 (G-42) .014 70 .12 .18 4.000 87 Plain ends 5 12
.234 1.12 020-040 (G-40) .020 34 .50 .75 2.380 2.25 Full loops 5 12
.156 2.06 020-035 (G-35) .020 Brass 90 .25 .50 1.180 1.75 Full loops 10 12
.370 3.25 020-019 (G-19) .041 66 1.50 1.90 4.000 8.00 Half loops 9 12
.250 4.00 020-020 (G-20) .0286 118 .25 .81 1.500 4.00 Full loops 10 12
.480 4.50 020-022 (G-22) .0625 57.5 1.00 6.20 3.000 17.00 Full loops 5 12
.440 5.25 020-028 (G-28) .0625 74 3.00 6.50 4.000 58.00 Full loops 5 12
.550 5.62 020-012 (G-12) .080 58.5 4.00 10.00 2.620 31.00 Full loops 4 12
.250 5.75 020-017 (G-17) .0286 181 .62 .44 2.250 4.50 Full loops 10 12
.440 6.44 020-009 (G-9) .048 118.5 2.00 1.10 7.500 10.50 Dbl. loops 5 12
.328 6.50 020-010 (G-10) .0348 162 1.25 .50 9.000 6.25 Dbl. loop,side 10 12
O.D. Max. Length Part Wire Comp. Rate Type Asst. N o.
Total Coils
Inches Rod Dia. Inches Number Diameter Per Inch Lbs. of E nds Qty. Box P er
.369 .281 .78 020-086 (G-86) .042 Brass 7.37 9 Sq. & Gr. 6 12
.282 .188 1.31 020-079 (G-79) .040 17.00 13 Plain 5 12
.315 .266 1.96 020-081 (G-81) .022 .56 23.5 Squared 5 12
.53X1.03X.86 .421 3.50 020-061 (G-61) .051 1.20 13 Sq. & Gr. 4 12
.875 .703 10.00 020-048 (G-48) .080 3.25 36 Plain 1 3
.375 .266 11.50 020-052 (G-52) .0475 2.25 88 Plain 3 12
.620 .500 11.50 020-050 (G-50) .054 1.00 60 Plain 3 6
For the small compression spring requirements, these

12 engineered sizes in quantities of 25 each make
this assortment the perfect helper.
300 COMPRESSION SPRINGS ASSORTMENT NO. 020-802

O.D. Max. length Part Wire Comp. Rate Total Type N o.
Inches Rod Dia. Inches Number Diameter Per Inch Lbs. Coils of E nds P er
.120 .078 .62 020-125 .016 6.60 13 Squared 25
.120 .075 .75 020-126 .016 5.30 18 Squared 25
.180 .125 .75 020-127 .022 8.60 11 Squared 25
.180 .125 1.00 020-128 .022 6.80 14 Squared 25
.180 .125 1.12 020-129 .022 6.00 15 Squared 25
.180 .125 1.25 020-130 .022 5.30 17 Squared 25
.240 .172 1.00 020-131 .026 7.80 11 Squared 25
.240 .172 1.25 020-132 .026 6.10 14 Squared 25
.240 .172 1.50 020-133 .026 5.10 15 Squared 25
.360 .281 1.50 020-134 .035 7.30 10 Squared 25
.360 .281 1.75 020-135 .035 6.20 11 Squared 25
.360 .281 2.00 020-136 .035 5.40 13 Squared 25
Like the above compression kit, only extension springs.

This kit can be a real helper. Packaged in the same
quantities in a clear container of 300 little giants.
300 EXTENSION SPRINGS ASSORTMENT NO. 020-803

O.D. Length Part Wire Appr. Init. Rate Per Max. Max. Safe Type N o . P er
Coils
Inches Inches Number Diameter Tension Lbs. Inch Lbs. Ext. L o ad L b s. of E nds B ox
.120 .62 020-137 .016 27 .06 3.70 .641 2.04 Full loops 25
.120 .75 020-138 .016 34 .31 2.50 .714 2.07 Full loops 25
.120 .88 020-139 .016 44 .19 2.20 .990 2.07 Full loops 25
.180 1.00 020-140 .022 32 .19 2.8 1.238 3.50 Full loops 25
.180 1.12 020-141 .022 36 .31 2.4 1.344 3.50 Full loops 25
.180 1.25 020-142 .022 42 .04 2.2 1.700 3.50 Full loops 25
.240 1.37 020-143 .026 39 .06 1.8 2.450 4.27 Full loops 25
.240 1.50 020-144 .026 42 .22 1.60 2.540 4.27 Full loops 25
.240 1.75 020-145 .026 53 .25 1.37 3.177 4.27 Full loops 25
.360 1.50 020-146 .037 25 .19 3.40 2.385 7.80 Full loops 25
.360 1.75 020-147 .037 29 .38 2.60 2.700 7.83 Full loops 25
.360 2.00 020-148 .037 36 .56 2.20 3.268 7.80 Full loops 25
26
UTILITY SPRINGS
INCH X 25.4 = MM
LBS. X .454 = KG
SQUARE WIRE CARBON STEEL DIE & FIXTURE SPRINGS

12-INCH LENGTHS PLAIN ENDS
Hole Rod Wire Space Max Safe Total Pounds Per Inch Approx. No. Per
Stock No.
Dia. Dia. Siz e Between Coils Load Lbs. Coils of Compression Solid Height Box
.375 .187 SR-0 .062 .047 25 111 121/2 7.50 12
.437 .250 SR-1A .062 .078 40 86 9 5.67 12
.500 .250 SR-1B .094 .078 100 70 42 7.10 12
.562 .312 SR-1 .094 .094 100 641/4 29 6.425 12
1
.562 .250 SR-4 .125 .062 245 64 /4 118 9.05 12
.687 .437 SR-2 .094 .125 75 55 151/2 5.42 12
.687 .375 SR-5 .125 .094 214 55 60 7.52 12
.687 .312 SR-10 .156 .062 450 55 180 9.68 12
.812 .562 SR-3 .094 .125 65 55 8.6 5.34 12
.812 .500 SR-6 .125 .109 170 5 1 1/ 4 35 6.87 12
.812 .437 SR-11 .156 .109 335 451/4 110 7.79 12
.812 .375 SR-16 .187 .094 550 423/4 280 9.10 12
.937 .625 SR-7 .125 .125 145 48 211/2 6.35 12
1
.937 .562 SR-12 .156 .109 275 45 /4 44 7.50 12
1.062 .750 SR-8 .125 .187 120 381/2 18 5.075 6
1.062 .687 SR-13 .156 .172 245 363/4 50 6.15 6
1.062 .625 SR-18 .187 .156 400 35 120 7.00 6
1.062 .437 SR-23 .250 .109 1200 331/2 575 9.67 6
1.187 .875 SR-9 .125 .250 100 32 141/2 4.20 6
1.187 .812 SR-14 .156 .187 220 35 45 5.80 6
1.187 .750 SR-19 .187 .187 350 32 90 6.30 6
1.187 .562 SR-24 .250 .125 1000 32 380 9.05 6
1.312 .937 SR-15 .156 .250 290 291/2 29 4.88 6
1.312 .875 SR-20 .187 .187 300 32 65 6.25 6
1.437 1.000 SR-21 .187 .312 270 24 60 4.63 6
1.562 1.125 SR-22 .187 .312 240 24 421/2 4.59 6
1
1.562 .937 SR-27 .250 .203 650 26 /2 155 7.26 6
1.562 .203 SR-31 .312 .187 1350 24 490 8.15 6
1.812 1.187 SR-28 .250 .343 575 201/4 115 5.52 6
1.812 1.062 SR-32 .312 .250 1150 211/2 305 7.425 6
2.062 1.437 SR-29 .250 .437 500 171/2 85 4.77 6
2.062 1.312 SR-33 .312 .297 1000 193/4 210 6.79 6
2.312 1.687 SR-30 .250 .531 425 151/2 65 4.18 6
2.312 1.562 SR-34 .312 .406 850 163/4 160 5.75 6
2.562 1.812 SR-35 .312 .437 750 16 115 5.45 6
27
GLOSSARY OF MECHANICAL SPRING TERMINOLOGY
ACTIVE COILS: those coils, which are HYSTERESIS: the mechanical energy solid height a compression spring which
free to deflect under load. loss that always occurs under cyclic load- has been coiled longer than the desired
ing and unloading of a spring, proportional finished length, so as to increase the ap-
ANGULAR RELATIONSHIP OF ENDS: to the area between the loading and un- parent elastic limit.
the relative position of the plane of the loading load-deflection curves within the
hooks of loops of extension springs to elastic range of a spring. RESIDUAL STRESS: stresses induced by
each other. set removal, shot peening cold-working,
INITIAL TENSION: the force that tends forming or other means. These stresses
BLUE: a thin blue film of oxide on fer- to keep the coils of an extension spring may or may not be beneficial, depending
rous alloys, sometimes used to indicate closed and which must be overcome be- on the application.
that the material has been stress relieved. fore the coils start to open.
SET: permanent distortion, which occurs
BAKING: heating of electroplated LOAD: the force applied to a spring that when a spring is stressed beyond the elas-
springs to relieve hydrogen causes a deflection. tic limit of the material.
embrittlement.
LOOPS: coil-like wire shapes at the ends SHOT PEENING: a cold-working process
BUCKLING: bowing or lateral deflection of extension springs that provide for at- in which the material surface is peened to
of compression springs when com- tachment and force application. induce compressive stresses and thereby
pressed, related to the slenderness ra- improve fatigue life.
tio. MEAN COIL DIAMETER: outside spring
diameter (O.D.) minus one wire diam- SLENDERNESS RATIO: ratio of spring
CLOSED ENDS: ends of compression eter. length to mean coil diameter.
springs where pitch of the end coils is
reduced so that the end coils touch. MODULUS IN SHEAR OR TORSION: co- SOLID HEIGHT: length of a compression
efficient of stiffness for extension and com- spring when under sufficient load to bring
CLOSED AND GROUND ENDS: as with pression springs. all coils into contact with adjacent coils.
closed ends, except that the end is
ground to provide a flat plane. MODULUS IN TENSION OR BENDING: SPRING INDEX: ratio of mean coil diam-
coefficient of stiffness used for torsion and eter to wire diameter.
CLOSED LENGTH: see Solid Height. flat springs (Youngs Modulus).
SQUARED AND GROUND ENDS: Refer to
CLOSE-WOUND: coiled with adjacent MOMENT: see Torque. Closed and Ground Ends.
coils touching.
OPEN ENDS, NOT GROUND: end of a com- SQUARED ENDS: Refer to Closed Ends.
COILS PER INCH: see Pitch. pression spring with a constant pitch for
each coil. SQUARENESS OF ENDS: angular devia-
FREQUENCY (NATURAL): the lowest tion between the axis of a compression
inherent rate of free vibration of a spring OPEN ENDS GROUND: open ends, not spring and a normal to the plane of the
itself (usually in cycles per second) with ground, followed by and end grinding ends.
ends restrained. operation.
SQUARENESS UNDER LOAD: as in
GRADIENT: see Rate. PASSIVATING: acid treatment of stain- Squareness of Ends, except with the
less steel to remove contaminants and spring under load.
HEAT SETTING: fixturing a spring at el- improve corrosion resistance.
evated temperature to minimize loss of STRESS RANGE: the difference in opera-
load at operating temperature. PERMANENT SET: a material that is de- tion stresses at minimum and maximum
flected so far that its elastic properties loads.
HELIX: the spiral form (open or closed) have been exceeded and it does not re-
of compression, extension and torsion turn to its original condition upon release STRESS RELIEVE: to subject springs to
springs. of load is said to have taken a perma- low-temperature heat treatment so as to
nent set. relieve residual stresses.
HOOKS: open loops or ends of exten-
sion springs. PITCH: the distance from center to cen- TORQUE: a twisting action in torsion
ter of the wire in adjacent active coils (rec- spring, which tends to produce rotation,
HOT PRESSING: see Heat Setting. ommended) practive is to specify num- equal to the load multiplied by the distance
ber of active coils rather then pitch). (or moment arm) from the load to the axis
HYDROGEN EMBRITTLEMENT: hydro- of spring body. Usually express in inch-
gen absorbed in electroplating or pick- PRESET: see Remove Set. oz., inch pounds or in foot-pounds.
ling of carbon steels, tending to make
the spring material brittle and suscep- RATE: change in load per unit deflection, TOTAL NUMBER OF COILS: number of
tible to cracking and failure, particularly generally given in pounds per inch. active coils plus the coils forming the ends.
under sustained loads.
REMOVE SET: the process of closing to TRAPPED STRESS: see Residual Stress.
28
Lami-Flex Urethane Springs For optimum tool & die operation, specific characteristics have
been specially compounded and processed for LAMI-FLEX
springs. These qualities enhance their use in the aircraft, auto-
motive, appliance, electrical and electronic industries.
PRESSURE RANGE GUIDE These special qualities are:
(Force per 1/8 deflection)
1. Corrosion resistant
2. Higher pressures
Conventional heavy duty steel die spring 3. Increased durability
--- Up to 488 lbs. 4. Unaffected by oil, chemicals, solvents
LAMI-FLEX Urethane Die Springs & Strippers 5. Lighter weight
6. Longer life
--- Up to 2593 lbs.
7. Abrasion resistant
LAMI-FLEX Bars (Pressure Pads) 8. Low noise
---Up to 90,000 lbs. 9. No sharpnellizing
LAMI-FLEX Slabs (Pressure Pads) 10. Low cost
--- Unlimited
LAMI-FLEX springs exceed the capability of coiled steel springs
LAMI-FLEX bar or rectangular stock is ideally in generated forces and strokes in a smaller space. This
suited for replacement of rows of springs is accomplished by the non-compressibility and resiliency.
because of its long, horizontal axis. Character- Its volume remains constant under force but changes shape,
istics of rubber are surpassed with LAMI-FLEX similar to a solid fluid with a memory. Under load,
having three times the wear life. LAMI-FLEX springs produce a high, uniform, and continuous
counter pressure, returning to original shape when load is
released.
Temperatures, many of our compounds stay flexible at

well below -40F, even though they gradually stiffen as the
temperature falls below 0F. Continuous use above 230F
is not recommended. Our urethanes can be used intermit-
tently up to 250F.
Heat build-up, due to internal friction (hysteresis effect), is

the most common cause of premature failure of urethane.
The amount of heat generated is a direct function of effec-
tive strokes per hour and/or degree of deflection per stroke.
Thus, in selecting springs or pressure pads, minimize the
percentage of deflection for longer life - particularly when
exceeding 700 strokes per hour.
Operating Speed & % of Deflection,

Short runs or slow speed -- Up to 200 strokes per hour
--above 25% of spring height.
Intermittent -- Up to 700 strokes per hour -- up to 25%

of spring height.
Continuous -- Up to 12,000 strokes per hour -- up to 15%

of spring height.
Cutting of Urethane
Bandsawing -- Use any type of conventional saw with 4 hook
(sharp) carbon blade with raker set.
Lathe Cutting -- Use H.S.S. tool bits with positive rake of

from 5 to 10 degrees. WHEN ORDERING PLEASE SPECIFY:
1. Quantity
2. Thickness or Diameter
*Available in 90A or 95A Durometer. Custom 3. Length
sizes and hardness available upon request.
29
LAMI-FLEX 90A bars, slabs, sheets and rods:
L = Length W = Width r = radius h = height d = diameter

* Area (A) P.S.I. or Deflection from graph
1) For Solid rectangles or square: 1) Interpolate for in between shape factor
A=LxW 2) For shape factors less than 0.5 use 0.5 line
* Shape Factor (S.F.) * Convert P.S.I. to load pounds

1) For solid sheets, slabs or bars: 1) Load pounds = p.s.i. x area
S.F. = 2hLxW(L+W)
2) This is total force required to deflect a given distance
2) For solid rods:
S.F. = __d__
4h
EXAMPLE: How much pressure will be required to deflect a 6 x 6 x 1 slab by .150?

* Since .150 is 15% of 1, find 15% on graph below
A = 6 x 6 = 36 * Since 1.5 shape factor is halfway between 1.0 and 2.0 lines on the
___6 x 6____
S.F. = 2(1)(6 + 6) =1.5 graph the p.s.i. value for 15% is 1220.
Load = 1220 x 36 * Multiply p.s.i. times area to get load pounds = 43,920
LAMI-FLEX SHEET, SLAB, ROD SAMPLE PRESSURES

90A DUROMETER
Load Pounds Required to
SIZE Deflect
1/8" 1/4" 3/8"
1/4" dia. x 1/2" height 55 N.R. N.R.
3/8" dia. x 3/4" height 90 165 N.R.
1/2" dia. x 1" height 125 225 N.R.
5/8" dia. x 1-1/4" height 165 290 455
3/4" dia. x 1-1/2 height 210 360 510
7/8" dia. x 1-3/4" height 245 425 600
1" dia. x 2" height 300 505 705
1-1/8" dia. x 2-1/4" height 350 585 795
1-1/4" dia. x 2-1/2" height 380 665 910
1-1/2" dia. x 3" height 510 815 1130
2" dia. x 3" height 910 1445 2010
3" dia. x 3" height 2050 3250 3620
4" dia. x 3" height 3645 5780 7070
6" dia. x 3" height 8200 13005 18095
1" w ide x 12" long x 1" height 7560 12900 N.R.
2" w ide x 2" long x 3" height 7200 11400 15000
6" w ide x 6" long x 1" height 37800 70200 N.R.
12" w ide x 12" long x 1-1/2" height 120960 230400 338400
N.R. = RECOMMENED ! LAMI-FLEX springs can be used as die springs
Urethane will conform to the many shapes and angles of and strippers.
forming tools. This feature along with ease of installation ! LAMI-FLEX solid rod can be used as springs,
makes urethane a top choice among metal stampers in pressure pads, in roll forming opera
Europe and Asia. LAMI-FLEX urethane is a stocked item, tions and in bulging operations.
which is readily available to you here in the USA & Canada.
! LAMI-FLEX bars can be used in place of rows of
Custom sizes, shape, colors and durometers of LAMI-FLEX steel springs, as pressure pads and
can also be custom molded for special needs and proto- in press brake tooling.
types. Please send requests for quotations to your local ! LAMI-FLEX solid sheets and slabs can be used
Lamina distributor or to: as pressure pads, forming blocks,
embossing, pressbrakes, dampeners
Lamina Components and bumpers.
P.O. Box 2540, Farmington Hills, MI. 48333
Note: All values in this publication are based on tests as free
Phone: 248-489-9122, 800-652-6462
standing cylinders or sections with ends unattached. Confine-
Fax: 248-553-6842 ment of any portion of the diameter or periphery, or bonding of
E-mail: [email protected] ends to restrict lateral movement will substantially increase these
values. Conversely, lubrication of ends will assist lateral move-
ment, and will tend to reduce these values.
30
Light Duty
LAMI-FLEX SPRINGS
95A DUROMETER
PART OUTSIDE FITS LENGTH LOAD LOAD POUNDS REQUIRED TO DEFLECT

NUMBER DIA PU N C H (L) LBS.
(O.D.) SHANK REQD. 5 % 10% 15% 20% 25%
(A) TO LENGTH LENGTH LENGTH LENGTH LENGTH
DEFLECT LOAD OF LOAD OF LOAD OF LOAD OF LOAD OF
1/8" LBS. DEFL. LBS. DEFL. LBS. DEFL. LBS. DEFL. LBS. DEFL.
LFL06918-100 1 270 .0500 .1000 .1500 .2000 .2500
LFL06918-125 1-1/4 240 175 .0625 240 .1250 295 .1875 350 .2500 375 .3125
LFL06918-150 11/16 3/16 1-1/2 220 .0750 .1500 .2250 .3000 .3750
LFL06918-1250 12-1/2
LFL07525-100 1 300 .0500 .1000 .1500 .2000 .2500
LFL07525-125 1-1/4 270 .0625 .1250 .1875 .2500 .3125
LFL07525-150 1-1/2 250 200 .0750 270 .1500 335 .2250 395 .3000 430 .3750
LFL07525-175 3/4 1/4 1-3/4 230 .0875 .1750 .2625 .3500 .4375
LFL07525-200 2 220 .1000 .2000 .3000 .4000 .5000
LFL07525-1250 12-1/2
LFL08131-100 1 340 .0500 .1000 .1500 .2000 .2500
LFL08131-125 1-1/4 300 .0625 .1250 .1875 .2500 .3125
LFL08131-150 1-1/2 275 220 .0750 300 .1500 375 .2250 445 .3000 480 .3750
LFL08131-175 13/16 5/16 1-3/4 255 .0875 .1750 .2625 .3500 .4375
LFL08131-200 2 245 .1000 .2000 .3000 .4000 .5000
LFL08131-1250 12-1/2
LFL08838-100 1 375 .0500 .1000 .1500 .2000 .2500
LFL08838-125 1-1/4 335 .0625 .1250 .1875 .2500 .3125
LFL08838-150 1-1/2 305 245 .0750 335 .1500 415 .2250 490 .3000 530 .3750
LFL08838-175 1-3/4 280 .0875 .1750 .2625 .3500 .4375
LFL08838-200 7/8 3/8 2 270 .1000 .2000 .3000 .4000 .5000
LFL08838-225 2-1/4 250 .1125 .2250 .3375 .4500 .5625
LFL08838-250 2-1/2 245 .1250 .2500 .3750 .5000 .6250
LFL08838-2500 25
LFL10050-100 1 440 .0500 .1000 .1500 .2000 .2500
LFL10050-125 1-1/4 395 .0625 .1250 .1875 .2500 .3125
LFL10050-150 1-1/2 360 .0750 .1500 .2250 .3000 .3750
LFL10050-175 1-3/4 330 290 .0875 395 .1750 490 .2625 585 .3500 635 .4375
LFL10050-200 1 1/2 2 315 .1000 .2000 .3000 .4000 .5000
LFL10050-225 2-1/4 270 .1125 .2250 .3375 .4500 .5625
LFL10050-250 2-1/2 290 .1250 .2500 .3750 .5000 .6250
LFL10050-2500 25
LFL11363-100 1 515 .0500 .1000 .1500 .2000 .2500
LFL11363-125 1-1/4 460 .0625 .1250 .1875 .2500 .3125
LFL11363-150 1-1/2 420 .0750 .1500 .2250 .3000 .3750
LFL11363-175 1-3/4 385 335 .0875 460 .1750 570 .2625 680 .3500 735 .4375
LFL11363-200 1-1/8 5/8 2 365 .1000 .2000 .3000 .4000 .5000
LFL11363-225 2-1/4 345 .1125 .2250 .3375 .4500 .5625
LFL11363-250 2-1/2 335 .1250 .2500 .3750 .5000 .6250
LFL11363-2500 25
LFL13875-125 1-1/4 685 .0625 .1250 .1875 .2500 .3125
LFL13875-150 1-1/2 625 .0750 .1500 .2250 .3000 .3750
LFL13875-175 1-3/4 575 .0875 .1750 .2625 .3500 .4375
LFL13875-200 2 545 495 .1000 685 .2000 855 .3000 1020 .4000 1105 .5000
LFL13875-225 1-3/8 3/4 2-1/4 515 .1125 .2250 .3375 .4500 .5625
LFL13875-250 2-1/2 495 .1250 .2500 .3750 .5000 .6250
LFL13875-275 2-3/4 455 .1375 .2750 .4125 .5500 .6875
LFL13875-300 3 410 .1500 .3000 .4500 .6000 .7500
LFL13875-2500 25
LFL15088-125 1-1/4 1000 .0625 .1250 .1875 .2500 .3125
LFL15088-150 1-1/2 950 .0750 .1500 .2250 .3000 .3750
LFL15088-175 1-3/4 890 .0875 .1750 .2625 .3500 .4375
LFL15088-200 2 850 750 .1000 1000 .2000 1200 .3000 1400 .4000 1650 .5000
LFL15088-225 1-1/2 7/8 2-1/4 800 .1125 .2250 .3375 .4500 .5625
LFL15088-250 2-1/2 750 .1250 .2500 .3750 .5000 .6250
LFL15088-275 2-3/4 710 .1375 .2750 .4125 .5500 .6875
LFL15088-300 3 670 .1500 .3000 .4500 .6000 .7500
LFL15088-2500 25
95A Durometer Product is Blue 31

Light Duty
LAMI-FLEX SPRINGS,
Continued 95A DUROMETER

NUMBER DIA. PU N C H (L) LB S .
5% 10% 15% 20% 25%
(O.D.) SHANK REQD.
(A) TO LE N GTH LE N GTH LE N GTH LE N GTH LENGTH
DEFLECT LOAD OF LOAD OF LOAD OF LOAD OF LOAD OF
LFL17510-125 1-1/4 1050 .0625 .1250 .1875 .2500 .3125
LFL17510-150 1-1/2 910 .0750 .1500 .2250 .3000 .3750
LFL17510-175 1-3/4 880 .0875 .1750 .2625 .3500 .4375
LFL17510-200 2 840 .1000 .2000 .3000 .4000 .5000
LFL17510-225 2-1/4 790 750 .1125 950 .2250 1250 .3375 1650 .4500 2000 .5625
1-3/4 1
LFL17510-250 2-1/2 755 .1250 .2500 .3750 .5000 .6250
LFL17510-275 2-3/4 690 .1375 .2750 .4125 .5500 .6875
LFL17510-300 3 625 .1500 .3000 .4500 .6000 .7500
LFL17510-400 4 570 .2000 .4000 .6000 .8000 1.0000
LFL17510-2500 25
Medium Duty LAMI-FLEX SPRINGS

NUMBER DIA. PU N C H (L) LB S . 5% 10% 15% 20% 25%
(O.D.) SHANK REQD. TO LENGTH LENGTH LENGTH LENGTH LENGTH
(A) DEFLECT LOAD OF LOAD OF LOAD OF LOAD OF LOAD OF
LFM08118-100 1 440 .0500 .1000 .1500 .2000 .2500
LFM08118-125 1-1/4 375 235 .0625 375 .1250 500 .1875 600 .2500 750 .3125
13/16 3/16
LFM08118-150 1-1/2 330 .0750 .1500 .2250 .3000 .3750
LFM08118-1250 12-1/2
LFM08825-100 1 420 .0500 .1000 .1500 .2000 .2500
LFM08825-125 1-1/4 365 205 .0625 365 .1250 470 .1875 630 .2500 825 .3125
LFM08825-150 7/8 1/4 1-1/2 310 .0750 .1500 .2250 .3000 .3750
LFM08825-175 1-3/4 245 .0875 .1750 .2625 .3500 .4375
LFM08825-1250 12-1/2
LFM09431-100 1 500 .0500 .1000 .1500 .2000 .2500
LFM09431-125 1-1/4 425 .0625 .1250 .1875 .2500 .3125
LFM09431-150 1-1/2 355 225 .0750 425 .1500 575 .2250 750 .3000 965 .3750
15/16 5/16
LFM09431-175 1-3/4 310 .0875 .1750 .2625 .3500 .4375
LFM09431-200 2 270 .1000 .2000 .3000 .4000 .5000
LFM09431-2500 25
LFM10038-100 1 610 .0500 .1000 .1500 .2000 .2500
LFM10038-125 1-1/4 500 .0625 .1250 .1875 .2500 .3125
LFM10038-150 1-1/2 470 .0750 .1500 .2250 .3000 .3750
LFM10038-175 1-3/4 430 345 .0875 500 .1750 725 .2625 915 .3500 1150 .4375
1 3/8
LFM10038-200 2 400 .1000 .2000 .3000 .4000 .5000
LFM10038-225 2-1/4 360 .1125 .2250 .3375 .4500 .5625
LFM10038-250 2-1/2 345 .1250 .2500 .3750 .5000 .6250
LFM10038-2500 25
LFM11350-100 1 590 .0500 .1000 .1500 .2000 .2500
LFM11350-125 1-1/4 530 .0625 .1250 .1875 .2500 .3125
LFM11350-150 1-1/2 485 .0750 .1500 .2250 .3000 .3750
LFM11350-175 1-3/4 445 385 .0875 530 .1750 660 .2625 785 .3500 850 .4375
1-1/8 1/2
LFM11350-200 2 425 .1000 .2000 .3000 .4000 .5000
LFM11350-225 2-1/4 400 .1125 .2250 .3375 .4500 .5625
LFM11350-250 2-1/2 385 .1250 .2500 .3750 .5000 .6250
LFM11350-2500 25
32 95A Durometer Product is Blue

Medium Duty
LAMI-FLEX SPRINGS,

1/8" LBS. DEFL. LBS. DEFL. LBS. DEFL. LBS. DEFL. LBS. LBS.
LFM12563-100 1 680 .0500 .1000 .1500 .2000 .2500
LFM12563-125 1-1/4 605 .0625 .1250 .1875 .2500 .3125
LFM12563-150 1-1/2 555 .0750 .1500 .2250 .3000 .3750
LFM12563-175 1-3/4 510 440 .0875 605 .1750 760 .2625 905 .3500 975 .4375
LFM12563-200 1-1/4 5/8 2 485 .1000 .2000 .3000 .4000 .5000
LFM12563-225 2-1/4 460 .1125 .2250 .3375 .4500 .5625
LFM12563-250 2-1/2 450 .1250 .2500 .3750 .5000 .6250
LFM12563-2500 25
LFM15075-125 1-1/4 865 .0625 .1250 .1875 .2500 .3125
LFM15075-150 1-1/2 790 .0750 .1500 .2250 .3000 .3750
LFM15075-175 1-3/4 720 .0875 .1750 .2625 .3500 .4375
LFM15075-200 2 690 .1000 .2000 .3000 .4000 .5000
LFM15075-225 1-1/2 3/4 2-1/4 650 625 .1125 865 .2250 1085 .3375 1290 .4500 1400 .5625
LFM15075-250 2-1/2 625 .1250 .2500 .3750 .5000 .6250
LFM15075-275 2-3/4 570 .1375 .2750 .4125 .5500 .6875
LFM15075-300 3 515 .1500 .3000 .4500 .6000 .7500
LFM15075-2500 25
LFM16388-125 1-1/4 970 .0625 .1250 .1875 .2500 .3125
LFM16388-150 1-1/2 890 .0750 .1500 .2250 .3000 .3750
LFM16388-175 1-3/4 810 .0875 .1750 .2625 .3500 .4375
LFM16388-200 2 730 .1000 .2000 .3000 .4000 .5000
LFM16388-225 1-5/8 7/8 2-1/4 650 585 .1125 970 .2250 1375 .3375 1725 .4500 3000 .5625
LFM16388-250 2-1/2 585 .1250 .2500 .3750 .5000 .6250
LFM16388-275 2-3/4 515 .1375 .2750 .4125 .5500 .6875
LFM16388-300 3 440 .1500 .3000 .4500 .6000 .7500
LFM16388-2500 25
LFM20010-125 1-1/4 1520 .0625 .1250 .1875
LFM20010-150 1-1/2 1385 .0750 .1500 .2250
LFM20010-175 1-3/4 1470 .0875 .1750 .2625
LFM20010-200 2 1210 .1000 .2000 .3000
LFM20010-225 2-1/4 1140 1090 .1125 1520 .2250 1910 .3375 N.R. N.R.
LFM20010-250 2 1 2-1/2 1090 .1250 .2500 .3750
LFM20010-275 2-3/4 1000 .1375 .2750 .4125
LFM20010-300 3 905 .1500 .3000 .4500
LFM20010-400 4 785 .2000 .4000 .6000
LFM20010-2500 25
LFM25012-125 1-1/4 2365 .0625 .1250 .1875
LFM25012-150 1-1/2 2255 .0750 .1500 .2250
LFM25012-175 1-3/4 1930 .0875 .1750 .2625
LFM25012-200 2 1880 .1000 .2000 .3000
LFM25012-225
LFM25012-250 2-1/2 1-1/4 22--11//42 1770
1695
1695 .1125
.1250
2365 .2250
.2500
3115 .3375
.3750
N.R. N.R.
LFM25012-275 2-3/4 1550 .1375 .2750 .4125

LFM25012-300 3 1400 .1500 .3000 .4500
LFM25012-400 4 1260 .2000 .4000 .6000
LFM25012-2500 25
LFM25015-125 1-1/4 2760 .0625 .1250 .1875
LFM25015-150 1-1/2 2640 .0750 .1500 .2250
LFM25015-175 1-3/4 2500 .0875 .1750 .2625
LFM25015-200 2 2360 .1000 .2000 .3000
LFM25015-225
LFM25015-250 2-1/2 1-1/2 22--11//42 2220
1990
1990 .1125
.1250
2760 .2250
.2500
3200 .3375
.3750
N.R. N.R.
LFM25015-275 2-3/4 1860 .1375 .2750 .4125

LFM25015-300 3 1730 .1500 .3000 .4500
LFM25015-400 4 1610 .2000 .4000 .6000
LFM25015-2500 25

Heavy Duty
LAMI-FLEX SPRINGS
95A DUROMETER

LFH09418-100 1 480 .0500 .1000 .1500 .2000 .2500
LFH09418-125 1-1/4 355 265 .0625 355 .1250 .1875 .2500 .3125
LFH09418-150 15/16 3/16 1-1/2 340 .0750 .1500
610
.2250
825
.3000
1060
.3750
LFH09418-1250 12-1/2
LFH10025-100 1 667 .0500 .1000 .1500 .2000 .2500
LFH10025-125 1-1/4 575 .0625 .1250 .1875 .2500 .3125
LFH10025-150 1 1/4 1-1/2 520 365 .0750 575 .1500 760 .2250 985 .3000 1300 .3750
LFH10025-175 1-3/4 445 .0875 .1750 .2625 .3500 .4375
LFH10025-1250 12-1/2
LFH11331-100 1 775 .0500 .1000 .1500 .2000 .2500
LFH11331-125 1-1/4 670 .0625 .1250 .1875 .2500 .3125
LFH11331-150 1-1/2 625 460 .0750 670 .1500 880 .2250 1125 .3000 1435 .3750
LFH11331-175 1-1/8 5/16 1-3/4 535 .0875 .1750 .2625 .3500 .4375
LFH11331-200 2 470 .1000 .2000 .3000 .4000 .5000
LFH11331-2500 25
LFH11338-100 1 785 .0500 .1000 .1500 .2000 .2500
LFH11338-125 1-1/4 675 .0625 .1250 .1875 .2500 .3125
LFH11338-150 1-1/2 610 .0750 .1500 .2250 .3000 .3750
LFH11338-175 1-3/4 520 420 .0875 675 .1750 900 .2625 1185 .3500 1485 .4375
LFH11338-200 1-1/8 3/8 2 470 .1000 .2000 .3000 .4000 .5000
LFH11338-225 2-1/4 435 .1125 .2250 .3375 .4500 .5625
LFH11338-250 2-1/2 420 .1250 .2500 .3750 .5000 .6250
LFH11338-2500 25
LFH12550-100 1 760 .0500 .1000 .1500 .2000 .2500
LFH12550-125 1-1/4 675 .0625 .1250 .1875 .2500 .3125
LFH12550-150 1-1/2 620 .0750 .1500 .2250 .3000 .3750
LFH12550-175 1-3/4 565 490 .0875 675 .1750 845 .2625 1010 .3500 1090 .4375
LFH12550-200 1-1/4 1/2 2 540 .1000 .2000 .3000 .4000 .5000
LFH12550-225 2-1/4 510 .1125 .2250 .3375 .4500 .5625
LFH12550-250 2-1/2 490 .1250 .2500 .3750 .5000 .6250
LFH12550-2500 25
LFH13863-100 1 1105 .0500 .1000 .1500 .2000 .2500
LFH13863-125 1-1/4 960 .0625 .1250 .1875 .2500 .3125
LFH13863-150 1-1/2 900 .0750 .1500 .2250 .3000 .3750
LFH13863-175 1-3/4 770 660 .0875 960 .1750 1250 .2625 1610 .3500 1800 .4375
LFH13863-200 1-3/8 5/8 2 725 .1000 .2000 .3000 .4000 .5000
LFH13863-225 2-1/4 695 .1125 .2250 .3375 .4500 .5625
LFH13863-250 2-1/2 660 .1250 .2500 .3750 .5000 .6250
LFH13863-2500 25
LFH17575-125 1-1/4 1270 .0625 .1250 .1875 .2500 .3125
LFH17575-150 1-1/2 1160 .0750 .1500 .2250 .3000 .3750
LFH17575-175 1-3/4 1060 .0875 .1750 .2625 .3500 .4375
LFH17575-200 2 1010 .1000 .2000 .3000 .4000 .5000
LFH17575-225 1-3/4 3/4 2-1/4 955 915 .1125 1270 .2250 1595 .3375 1905 .4500 2065 .5625
LFH17575-250 2-1/2 915 .1250 .2500 .3750 .5000 .6250
LFH17575-275 2-3/4 835 .1375 .2750 .4125 .5500 .6875
LFH17575-300 3 755 .1500 .3000 .4500 .6000 .7500
LFH17575-2500 25
LFH17588-125 1-1/4 1170 .0625 .1250 .1875 .2500 .3125
LFH17588-150 1-1/2 1065 .0750 .1500 .2250 .3000 .3750
LFH17588-175 1-3/4 975 .0875 .1750 .2625 .3500 .4375
LFH17588-200 2 930 .1000 .2000 .3000 .4000 .5000
LFH17588-225 1-3/4 7/8 2-1/4 875 840 .1125 1170 .2250 1465 .3375 1750 .4500 1895 .5625
LFH17588-250 2-1/2 840 .1250 .2500 .3750 .5000 .6250
LFH17588-275 2-3/4 770 .1375 .2750 .4125 .5500 .6875
LFH17588-300 3 695 .1500 .3000 .4500 .6000 .7500
LFH17588-2500 25
34 95A Durometer Product is Blue

Heavy Duty
LAMI-FLEX SPRINGS,

1/8 LBS. DEFL. LBS. DEFL. LBS. DEFL. LBS. DEFL. LBS. DEFL.
LFH22510-125 1-1/4 2050 .0625 .1250 .1875
LFH22510-150 1-1/2 1955 .0750 .1500 .2250
LFH22510-175 1-3/4 1670 .0875 .1750 .2625
LFH22510-200 2 1600 .1000 .2000 .3000
LFH22510-225 2-1/4 1530 1470 .1125 2050 .2250 2580 .3375
LFH22510-250 2-1/4 1 2-1/2 1470 .1250 .2500 .3750 N.R. N.R.
LFH22510-275 2-3/4 1410 .1375 .2750 .4125
LFH22510-300 3 1360 .1500 .3000 .4500
LFH22510-400 4 1315 .2000 .4000 .6000
LFH22510-2500 25
LFH27515-125 1-1/4 2680 .0625 .1250 .1875
LFH27515-150 1-1/2 2550 .0750 .1500 .2250
LFH27515-175 1-3/4 2185 .0875 .1750 .2625
LFH27515-200 2 2125 .1000 .2000 .3000
LFH27515-225 2-1/4 2000 .1125 .2250 .3375
LFH27515-250 2-3/4 1-1/2 2-1/2 1920 1920 .1250 2680 .2500 3365 .3750 N.R. N.R.
LFH27515-275 2-3/4 1790 .1375 .2750 .4125
LFH27515-300 3 1585 .1500 .3000 .4500
LFH27515-400 4 1435 .2000 .4000 .6000
LFH27515-2500 25
Extra Heavy Duty LAMI-FLEX SPRINGS

1/8 LBS. DEFL. LBS. DEFL. LBS. DEFL. LBS. DEFL. LBS. DEFL.
LFX15063-100 1 1220 .0500 .1000 .1500 .2000 .2500
LFX15063-125 1-1/4 1085 .0625 .1250 .1875 .2500 .3125
LFX15063-150 1-1/2 990 .0750 .1500 .2250 .3000 .3750
LFX15063-175 1-3/4 905 780 .0875 1083 .1750 1360 .2625 1620 .3500 1755 .4375
LFX15063-200 1-1/2 5/8 2 865 .1000 .2000 .3000 .4000 .5000
LFX15063-225 2-1/4 815 .1125 .2250 .3375 .4500 .5625
LFX15063-250 2-1/2 780 .1250 .2500 .3750 .5000 .6250
LFX15063-2500 25
LFX20088-125 1-1/4 1640 .0625 .1250 .1875
LFX20088-150 1-1/2 1495 .0750 .1500 .2250
LFX20088-175 1-1/4 1365 .0875 .1750 .2625
LFX20088-200 2 1305 1175 .1000 1640 .2000 .3000
LFX20088-225 2 7/8 2-1/4 1225 .1125 .2250 2055 .3375 N.R. N.R.
LFX20088-250 2-1/2 1175 .1250 .2500 .3750
LFX20088-275 2-3/4 1075 .1375 .2750 .4125
LFX20088-300 3 975 .1500 .3000 .4500
LFX20088-2500 25
LFX25010-125 1-1/4 3765 .0625 .1250 .1875
LFX25010-150 1-1/2 3445 .0750 .1500 .2250
LFX25010-175 1-3/4 2950 .0875 .1750 .2625
LFX25010-200 2 2780 .1000 .2000 .3000
LFX25010-225 2-1/4 2610 2445 .1125 3765 .2250 .3375
LFX25010-250 2-1/2 1 2-1/2 2445 .1250 .2500 4875 .3750 N.R. N.R.
LFX25010-275 2-3/4 2345 .1375 .2750 .4125
LFX25010-300 3 2265 .1500 .3000 .4500
LFX25010-400 4 .200 .4000 .6000
LFX25010-2500 25

LAMI-FLEX Solid Rods
90A and 95A Durometer
PART NUMBER PART NUMBER PART NUMBER

OUTSIDE LENGTH OUTSIDE LENGTH DIAMETER LENGTH
90A 95A DIA. 90A 95A DIA. 90A 95A
Natural Blue Natural Blue Natural Blue
LFR025-03 LFR025-03B 3" LFR100-03 LFR100-03B 3" LFR200-03 LFR200-03B 3"
LFR025-06 LFR025-06B 1/4 6" LFR100-06 LFR100-06B 6" LFR200-06 LFR200-06B 6"
LFR025-12 LFR025-12B 12" LFR100-12 LFR100-12B 1 12" LFR200-12 LFR200-12B 2 12"
LFR038-12 LFR038-12B 12" LFR113-12 LFR113-12B 1-1/8 12" LFR250-12 LFR250-12B 2-1/2 12"
LFR050-12 LFR050-12B 12" LFR125-12 LFR125-12B 1-1/4 12" LFR300-12 LFR300-12B 3 12"
LFR088-03 LFR088-03B 3" LFR175-03 LFR175-03B 3"
LFR088-06 LFR088-06B 7/8 6" LFR175-06 LFR175-06B 6"
LFR088-12 LFR088-12B 12" LFR175-12 LFR175-12B 1-3/4 12"
LFR088-24 LFR088-24B 24" LFR175-24 LFR175-24B 24" 95A Durometer is Blue
90A Durometer is Natural Color
LAMI-FLEX Solid Bars 95A Durometer is Blue

90A Durometer
PART NUMBER PART NUMBER

90A 95A Thick. Width Length 90A 95A Thick. Width Length
Natural Blue Natural Blue
LFB10010-06 LFB10010-06B 6" LFB20030-06 LFB20030-06B 6"
LFB10010-12 LFB10010-12B 12" LFB20030-12 LFB20030-12B 12"
LFB10010-24 LFB10010-24B 1 1 24" LFB20030-24 LFB20030-24B 2 3 24"
LFB10010-36 LFB10010-36B 36" LFB20030-36 LFB20030-36B 36"
LFB10010-48 LFB10010-48B 48" LFB20030-48 LFB20030-48B 48"
LFB10020-06 LFB10020-06B 6" LFB20040-06 LFB20040-06B 6"
LFB10020-12 LFB10020-12B 12" LFB20040-12 LFB20040-12B 12"
LFB10020-24 LFB10020-24B 1 2 24" LFB20040-24 LFB20040-24B 2 4 24"
LFB10020-36 LFB10020-36B 36" LFB20040-36 LFB20040-36B 36"
LFB10020-48 LFB10020-48B 48" LFB20040-48 LFB20040-48B 48"
LFB10030-06 LFB10030-06B 6" LFB30030-06 LFB30030-06B 6"
LFB10030-12 LFB10030-12B 12" LFB30030-12 LFB30030-12B 12"
LFB10030-24 LFB10030-24B 1 3 24" LFB30030-24 LFB30030-24B 3 3 24"
LFB10030-36 LFB10030-36B 36" LFB30030-36 LFB30030-36B 36"
LFB10030-48 LFB10030-48B 48" LFB30030-48 LFB30030-48B 48"
LFB10040-06 LFB10040-06B 6" LFB30040-06 LFB30040-06B 6"
LFB10040-12 LFB10040-12B 12" LFB30040-12 LFB30040-12B 12"
LFB10040-24 LFB10040-24B 1 4 24" LFB30040-24 LFB30040-24B 3 4 24"
LFB10040-36 LFB10040-36B 36" LFB30040-36 LFB30040-36B 36"
LFB10040-48 LFB10040-48B 48" LFB30040-48 LFB30040-48B 48"
LFB20020-06 LFB20020-06B 6" LFB40040-06 LFB40040-06B 6"
LFB20020-12 LFB20020-12B 12" LFB40040-12 LFB40040-12B 12"
LFB20020-24 LFB20020-24B 2 2 24" LFB40040-24 LFB40040-24B 4 4 24"
LFB20020-36 LFB20020-36B 36" LFB40040-36 LFB40040-36B 36"
LFB20020-48 LFB20020-48B 48" LFB40040-48 LFB40040-48B 48"
36
LAMI-FLEX Solid Sheets and Slabs
95A Durometer is Blue

PART NUMBER PART NUMBER PART NUMBER

90A 95A Thick. Width Lgth. 90A 95A Thick. Width Lgth. 90A 95A Thick. Width Lgth.
Natural Blue Natural Blue Natural Blue
LFS01306-06 LFS01306-06B 6" LFS06312-12 LFS06312-12B 12" LFS15018-18 LFS15018-18B 18"
1-1/2 18
LFS01306-12 LFS01306-12B 1/8 6 12" LFS06312-18 LFS06312-18B 5/8 12 18" LFS15018-24 LFS15018-24B 24"
LFS01306-18 LFS01306-18B 18" LFS06312-24 LFS06312-24B 24" LFS15024-24 LFS15024-24B 1-1/2 24 24"
5/8 18
1/8 12 2 6
LFS01312-18 LFS01312-18B 18" LFS06324-24 LFS06324-24B 5/8 24 24" LFS20006-18 LFS20006-18B 18"
1/8 18 3/4 6
LFS01218-24 LFS01218-24B 24" LFS07506-18 LFS07506-18B 18" LFS20012-18 LFS20012-18B 2 12 18"
LFS01324-24 LFS01324-24B 1/8 24 24" LFS07506-24 LFS07506-24B 24" LFS20012-24 LFS20012-24B 24"
2 18
LFS02506-12 LFS02506-12B 12" LFS07512-18 LFS07512-18B 3/4 12 18" LFS20018-24 LFS20018-24B 24"
1/4 6
3/4 18
2-1/2 6
LFS02512-18 LFS02512-18B 1/4 12 18" LFS07524-24 LFS07524-24B 3/4 24 24" LFS25006-18 LFS25006-18B 18"
1/4 18 1 6
2-1/2 18
LFS03806-12 LFS03806-12B 12" LFS10012-18 LFS10012-18B 1 12 18" LFS25018-24 LFS25018-24B 24"
3/8 6
1 18
3 6
LFS03812-18 LFS03812-18B 3/8 12 18" LFS10024-24 LFS10024-24B 1 24 24" LFS30006-18 LFS30006-18B 18"
3/8 18 1-1/4 6
3 18
LFS05006-12 LFS05006-12B 12" LFS12512-18 LFS12512-18B 1-1/4 12 18" LFS30018-24 LFS30018-24B 24"
1/2 6
1-1/4 18
4 6
LFS05012-18 LFS05012-18B 1/2 12 18" LFS12524-24 LFS12524-24B 1-1/4 24 24" LFS40006-18 LFS40006-18B 18"
LFS05012-24 LFS05012-24B 24' LFS15006-06 LFS15006-06B 6" LFS40006-24 LFS40006-24B 24"
1/2 18 1-1/2 6
LFS06306-06 LFS06306-06B 6" LFS15012-12 LFS15012-12B 12" LFS40018-18 LFS40018-18 18"
4 18
LFS06306-12 LFS06306-12B 12" LFS15012-18 LFS15012-18B 1-1/2 12 18" LFS40018-24 LFS40018-24B 24"
5/8 6
LFS06306-24 LFS06306-24B 24"
37
Schnorr Disc Springs
Guiding the Disc Spring
Disc springs arranged in stacks require a guide If possible, and particularly on dynamic ap- to a fine finish, or better still, ground. Addi-
to prevent lateral movement under load. Guides plication, the guide rod and end thrust faces tionally, lubrication with a molybdenum
may be located on the inside diameter D or in should be case hardened to a minimum of based high pressure grease is recom-
the outside diameter D of the springs, but the RC 55. The guide surface should be turned mended.
internal guide is to be preferred. The following
values are recommended for the clearance be-
tween the guide surface and the inside or out-
side diameter if the spring: (chart lists values).
Using close tolerance for the guides, the clear-

ance can be reduced a little since the inside di-
ameter does not reduce during the stroke when
the edges are at right angles to the flank. See
para. 6.6.
CORRECT WRONG CORRECT WRONG
DISC SPRINGS MAY BE USED SINGLY OR IN COMBINATION
When disc springs are used in stacks, effort To ensure stackability the end springs should DIAMETER CLEARANCE
should be made to keep the stacks as short have their outside diameter in contact with the D j or D e =
as possible. As the length increases so does abutment faces. This is only possible of
the friction and therefore the deflection of course with an even number of disc springs.
the individual discs becomes unequal, with up to 16.0 0.2
the greatest deflection being at the moving It is necessary to have the inside diameter in over 16.0 up to 20.0 0.3
end. As a guide it is recommended that the contact when the abutment faces are just a over 20.0 up to 28.0 0.4
stack length be restricted to approximately 3 little larger than inside diameter of the disc
times the outside diameter of the disc, and over 26.0 up to 31.0 0.5
springs. over 31.5 up to 50.0 0.6
the largest disc diameter be used.
over 50.0 up to 80.0 0.8
Not more than 2 or 3 discs should normally be over 80.0 up to 140.0 1.0
used in parallel for multiple stacks, especially
under dynamic conditions where consider- over 140.0 up to 250.0 1.6
able heat is generated.
3p Stack of Springs in PARALLEL
{
LOAD: Single spring load
multiplied by the number of
springs in parallel.
DEFLECTION: Same as for the
single spring.
2p
Single Springs Stacked in SERIES
{
LOAD: Same as for the single
Single spring.
LOAD
Spring DEFLECTION: Single spring

deflection multiplied by the number of
p springs in series.
Springs Stacked in SERIES PARALLEL
f 2f 3f 4f
{ LOAD: Single spring load multiplied by
the number of springs in each parallel
set.
DEFLECTION: Single spring deflection
DEFLECTION multiplied by the number of sets in the
Spring Stacking Linear or Regressive Curve stack.
38
Schnorr Corporation has specialized in the Tolerance Since the method is carried out in a drum it is
manufacture of disc springs for more then 50 Allowable variations are laid down in Din 2093. possible only with larger quantities and limita-
years. During this period of extraordinary tech- The tolerances on disc spring diameters are tion of an external diameter up to approximately
nical development many applications have been H 12/h 12. The permissible tolerance for the 80mm. Zinc and Cadmium are lower than steel
found for Schnorr disc springs because of their spring force F at s=0.75 h0 is given in the fol- on the electrochemical table and therefore a
unique characteristics and advantages. lowing table: self protecting effect occurs in the case of sur-
face damage.
Original SCHNORR DISC SPRINGS offer a
number of benefits with particular mention for A Chemical Nickel plating surface treatment is
the following features: also possible ie, the Durni-Coat process. With
1. Load/deflection curves of straight, progres- this method embrittlement is also avoided to a
sive, or regressive character according to the large extent. Because of the greater hardness
design requirements. of the nickel layer, durability under dynamic load-
ing comes into question. In the event of dam-
2. The simple adjustment of the springs stack
age, no self protection occurs since nickel lies
length by the addition or removal of individual discs,
higher than steel in the electrochemical table.
thus altering the spring stack characteristic. Further advice on specific applications can be
3. An efficient use of space and high spring The spring force must be measure on a single
disc exactly as specified in the standard. obtained from our engineers.
forces with small deflections.
4. Self-demanding, particularly with parallel Surface Working
The following table gives the tolerance for the
stacking. Surface working, especially by shot-peening, has
over all height OH according to DIN 2093
5. No setting or fatigue under normal loads. proved to be beneficial for disc springs subjected
6. Long service life. to dynamic loads. The result may increase the
7. A large range of possible applications for in- working life far in excess for the values shown in
dividual spring sizes simplifies stock-keeping. Figs 8,9 and 10. However, as shot-peening re-
duces the internal tensile stresses arising from
Term and Symbols scragging, shot-peening or other methods of
surface working are not recommended for discs
DOutside diameter in millimeters/inch
carrying static loads.
dInside diameter in millimeters/inch
PSpring load
hFormed height of unloaded single disc in
millimeters/inch Since these tolerance were computed for disc
OHOverall height of unloaded single disc in sizes specified in DIN 2093 certain limitations
millimeters/inch must be imposed for other discs in which the
fDeflection in millimeters/inch dimensional ratios differ from the standard
tThickness of a single disc in millimeters/inch springs. This also applies in the case of K disc
springs.
Material for Disc Springs Heat Treatment

All our springs are austempered. This method
The most important characteristic of a spring
of heat treatment is particularly effective for
is its ability to absorb elastic deformations springs, as it gives the maximum toughness and
caused by outside loads. Because of their high therefore considerable durability.
load/deflection ratios disc springs are especially
suitable for storing energy, dissipating shock According to DIN 2093 the hardness should be
loads, suspending moving masses, and for load RC 42-52 and in manufacture the optimum value
measurement. is selected with regard to spring size and tensile
stress.
It is preferable to make a spring as small as Pre-setting
possible, so special materials are used which After heat treatment each disc spring is
are highly elastic, or which possess high ten- scragged, i.e., pressed flat at least once. By
sile strength and a high elastic limit. doing so the spring is preset in such a way that
the overall height OH stays within the permis-
They should also have sufficient plastic defor- sible tolerance after being subject to loads up
mation ability beyond the elastic limit to permit 1.5, the maximum force at f=h.
the manufacture of cold worked springs, as well
as to minimize failure of springs under unex- Surface Protection
Unless stated, all our disc springs are supplied
pectedly high loads. Phosphated or oil blackened before oil dipping.
The Phosphated surface is preferred for the
The Design & Manufacturing of Disc Springs better protection it provides over oil blackening.
According to the Standard DIN 2093 There are Deposition of a metal coating on the surface is
three different groups of execution: also possible. The most frequently used mate-
Group 1: under 1.25mm rial is Zinc with a final passivation in Chrome
Group 2: from 1.25 to 6.0mm solution. Unfortunately, current methods of elec-
Group 3: over 6 up to 16mm tronically depositing metal coating from aque-
Schnorr manufactures the three groups as follows: ous solutions cause hydrogen embrittlement
Group 1: Cold formed which cannot be completely avoided in cases of
Group 2: Cold formed, outside and inside di- higher tensile steels this is the case with disc
ameters turned, corners on inner edge springs and safety washers. Schnorr therefore
radiused. introduced a mechanical plating process which
Group 3: Hot formed, springs turned all over, proves to be very successful over a number of
contact surfaces formed, all corners radiused, years where no Hydrogen embrittlement occurs.
and material thickness reduced.
39
TYPICAL DISC SPRING
Shown here are just a few examples that show the versatility of
APPLICATIONS Schnorr Disc Springs in industrial product. Contact our sales
representatives or design engineers for assistance on your
specific spring application.
This disc spring stack is used

Spring in a pile-driving machine. The
Die Spring This picture shows
operation is shown in three
typical phases.
Lock Washer M.A.N. steam turbine 1. Initial position
condensers weighing 2. Impact - the springs
Sealing Gaskets several hundred tons are compressed pro-
Shock Loading/Absorption being supported by a gressively from top to
very small number of bottom carried out by
Vibration Control discs arranged in 3 pneumatic assistance.
stacks.
Thermal Expansion 3. Return to initial position
also assisted by pneu-
matics.
Improvement of sealing
performance applies to
closing the gate until
the cone engages. The
springs compress and This illustration shows a shear pin assembly
the wedge forces the to a main shaft. To protect the shear pin from
Sectional view of the starter showing the side plate into close transient shock overload while working the
general arrangement of components. The watertight contact with connection link is fitted with double acting
windingspindle with ratchet is on the left. the valve faces. SCHNORR disc spring stack.
A spring with almost a zero rate is This device maintains a working The Demag unit shown is a standard
used for a negligible amount of force clearance, while aircraft adjuster device on all cranes used to automati-
variance despite the differences in friction materials wear, to ensure cally compensate for load and angle.
the cable diameter. Should one disc constant fluid displacement Note the small size of the disc spring
of the stack fracture, the clamping during operation. The force/travel stack when tremendous working loads
force would barely be affected and curve of the springs within are considered.
the unit would still be operational. the confines of such small
assemblies must match the
hydraulic pressure and friction
bushings. The rate and accuracy
of Schnorr Disc Springs make
them ideal for this purposes.
40
Disc Springs EN (NEWTON) = 0.102 kg inches x 25.4 = mm
= 0.225 lb. lbs. x .454 = kg
Inch Series
SIZE mm SIZE inch LOAD P - in lb, Defection f in inch
PART
NUMBER f = 0.25 h f = 0.50 h f = 0.75 h Flat = h
Overall
O.D. I.D. Matl. O.D. I.D. Matl. Travel
Hgt. P f P f P f P f # Bag
D d t D d t h
O.H.
DSZ010 9.53 4.960 0.40 .375 .195 .016 .012 .028 23 .003 41 .006 55 .008 68 .012 175
DSZ020 12.70 6.550 0.50 .500 .258 .020 .016 .035 35 .004 61 .008 82 .012 89 .016 150
DSZ030 12.70 6.550 0.60 .500 .258 .024 .016 .038 55 .004 100 .008 137 .012 171 .016 150
DSZ040 17.46 9.700 0.60 .687 .382 .024 .020 .043 44 .005 75 .010 100 .015 120 .020 125
DSZ050 17.46 9.700 0.70 .687 .382 .028 .020 .047 83 .005 113 .010 154 .015 180 .020 125
DSZ060 19.05 8.137 0.70 .750 .320 .028 .024 .051 61 .006 108 .012 138 .018 166 .024 125
DSZ070 19.05 8.137 0.80 .750 .320 .031 .024 .055 78 .006 138 .012 184 .018 225 .024 125
DSZ080 19.05 9.700 0.80 .750 .382 .031 .022 .053 74 .006 133 .011 181 .017 224 .022 125
DSZ090 19.05 9.700 0.90 .750 .382 .035 .022 .057 101 .006 185 .011 256 .017 322 .022 125
DSZ100 25.40 11.310 0.90 1.000 .445 .035 .031 .067 90 .008 154 .016 201 .023 239 .031 75
DSZ110 25.40 11.310 1.00 1.000 .445 .039 .031 .071 117 .008 204 .018 272 .023 330 .031 75
DSZ120 25.40 11.310 1.25 1.000 .445 .049 .026 .075 163 .007 304 .013 430 .020 549 .028 50
DSZ121 28.00 13.000 1.00 1.100 .512 .039 .035 .075 119 .009 204 .018 264 .026 313 .035 75
DSZ122 28.00 13.000 1.25 1.100 .512 .049 .033 .083 190 .008 342 .017 470 .025 585 .033 50
DSZ123 28.00 13.000 1.50 1.100 .512 .059 .028 .087 248 .007 470 .014 672 .021 866 .028 50
DSZ130 34.92 16.175 1.25 1.375 .637 .049 .045 .094 189 .011 337 .023 434 .034 511 .045 40
DSZ140 34.92 16.175 1.50 1.375 .637 .059 .043 .102 288 .011 511 .022 693 .032 853 .043 40
DSZ150 34.92 16.175 2.00 1.375 .637 .079 .031 .110 406 .008 781 .016 1130 .023 1480 .031 30
DSZ160 38.10 19.350 1.50 1.500 .762 .059 .055 .114 378 .014 638 .028 820 .041 963 .055 25
DSZ170 38.10 19.350 2.00 1.500 .762 .079 .043 .122 539 .011 1000 .022 1420 .032 1810 .043 25
DSZ180 38.10 19.350 2.50 1.500 .762 .098 .035 .134 760 .008 1470 .018 2150 .026 2810 .035 25
DSZ190 50.80 25.800 2.00 2.000 1.016 .078 .059 .138 476 .015 843 .030 1140 .044 1390 .059 15
DSZ200 50.80 25.800 2.50 2.000 1.016 .098 .059 .157 824 .015 1510 .030 2110 .044 2660 .059 15
DSZ210 50.80 25.800 3.00 2.000 1.016 .118 .047 .165 1020 .012 1960 .024 2840 .035 3700 .047 15
DSZ220 60.33 25.800 2.00 2.375 1.016 .079 .079 .157 508 .020 840 .040 1060 .059 1220 .079 10
DSZ230 60.33 25.800 2.50 2.375 1.016 .098 .079 .177 832 .020 1450 .040 1930 .058 2330 .079 10
DSZ240 60.33 25.800 3.00 2.375 1.016 .118 .063 .181 964 .016 1800 .032 2540 .047 3250 .063 10
Disc Spring Terminology and Symbols

D Outside Diameter (Inch or MM)
d Inside Diameter (Inch or MM)
P Load (Newtons or Pounds)
H Overall Height (Inch or MM)
h Formed Height of Disc (total travel to flat) (Inch or MM)
f Deflection (Inch or MM)
t Thickness of Material (Inch or MM)
41
Disc Springs EN (NEWTON) = 0.102 kg
= 0.225 lb.
inches x 25.4 = mm
lbs. x .454 = kg
PART O/A
NUMBER O.D. I.D. MATL. HGT [ f = 0.25 h ] [ f = 0.50 h ] [ f = 0.75 h ] [ FLAT f = h] # Bag
D d t O.H. LOAD P DEFL. f LOAD P DEFL. f LOAD P DEFL.f LOAD P DEFL.f
DSM0063203 MM 6.000 3.200 0.300 0.450 45 0.038 84 0.075 119 0.113 153 0.150
IN 0.236 0.126 0.012 0.018 10 0.001 19 0.003 27 0.004 35 0.006
DSM0083202 MM 8.000 3.200 0.200 0.400 12 0.050 20 0.100 26 0.150 30 0.200
IN 0.315 0.126 0.008 0.016 3 0.002 5 0.004 6 0.006 7 0.008
DSM0083203 MM 8.000 3.200 0.300 0.550 46 0.063 79 0.125 104 0.188 126 0.250
IN 0.315 0.126 0.012 0.022 10 0.002 18 0.005 24 0.007 28 0.010
DSM0083204 MM 8.000 3.200 0.400 0.600 69 0.050 130 0.100 185 0.150 238 0.200
IN 0.315 0.126 0.016 0.024 16 0.002 29 0.004 42 0.006 54 0.008 250
DSM0084202 MM 8.000 4.200 0.200 0.450 21 0.063 33 0.125 39 0.188 42 0.250
IN 0.315 0.165 0.008 0.018 5 0.002 8 0.005 9 0.007 9 0.010
DSM0084203 MM 8.000 4.200 0.300 0.550 52 0.063 147 0.100 210 0.150 269 0.200
IN 0.315 0.165 0.012 0.022 18 0.002 33 0.004 47 0.006 61 0.009
DSM0084204 MM 8.000 4.200 0.400 0.600 78 0.050 89 0.125 118 0.188 142 0.250
IN 0.315 0.165 0.016 0.024 18 0.002 20 0.005 27 0.007 32 0.010
DSM0103203 MM 10.000 3.200 0.300 0.650 51 0.088 82 0.175 98 0.263 108 0.350
IN 0.394 0.126 0.012 0.026 12 0.003 18 0.007 22 0.010 24 0.014
DSM0103204 MM 10.000 3.200 0.400 0.700 75 0.075 133 0.150 179 0.225 220 0.300
IN 0.394 0.126 0.016 0.028 17 0.003 30 0.006 40 0.009 50 0.012
DSM0103205 MM 10.000 3.200 0.500 0.750 104 0.063 195 0.125 279 0.188 357 0.250
IN 0.394 0.126 0.020 0.030 23 0.002 44 0.005 63 0.007 81 0.010 250
DSM0105202 MM 10.000 5.200 0.250 0.550 30 0.075 48 0.150 58 0.225 63 0.300
IN 0.394 0.205 0.010 0.022 7 0.003 11 0.006 13 0.009 14 0.012
DSM0105204 MM 10.000 5.200 0.400 0.700 88 0.075 155 0.150 209 0.225 257 0.300
IN 0.394 0.205 0.016 0.028 20 0.003 35 0.006 47 0.009 58 0.012
DSM0105205 MM 10.000 5.200 0.500 0.750 122 0.063 228 0.125 325 0.188 418 0.250
IN 0.394 0.205 0.020 0.030 27 0.002 52 0.005 73 0.007 94 0.010
DSM0124204 MM 12.000 4.200 0.400 0.800 85 0.100 141 0.200 178 0.300 206 0.400
IN 0.472 0.165 0.016 0.031 19 0.004 32 0.008 40 0.012 46 0.016
DSM0124205 MM 12.000 4.200 0.500 0.850 116 0.088 208 0.175 284 0.263 352 0.350
IN 0.472 0.165 0.020 0.033 26 0.003 47 0.007 64 0.010 79 0.014
DSM0124206 MM 12.000 4.200 0.600 1.000 224 0.100 405 0.200 557 0.300 694 0.400
IN 0.472 0.165 0.024 0.039 51 0.004 91 0.008 126 0.012 157 0.016
DSM0125205 MM 12.000 5.200 0.500 0.900 150 0.100 263 0.200 350 0.300 424 0.400
IN 0.472 0.205 0.020 0.035 34 0.004 59 0.008 79 0.012 96 0.016 200
DSM0125206 MM 12.000 5.200 0.600 0.950 196 0.088 361 0.175 506 0.263 641 0.350
IN 0.472 0.205 0.024 0.037 44 0.003 82 0.007 114 0.010 145 0.014
DSM0126205 MM 12.000 6.200 0.500 0.850 134 0.088 239 0.175 326 0.263 404 0.350
IN 0.472 0.244 0.020 0.033 30 0.003 54 0.007 74 0.010 91 0.014
DSM0126206 MM 12.000 6.200 0.600 0.950 214 0.088 394 0.175 552 0.263 699 0.350
IN 0.472 0.244 0.024 0.037 48 0.003 89 0.007 125 0.010 158 0.014
DSM0135205 MM 12.500 5.200 0.500 0.850 111 0.088 200 0.175 272 0.263 337 0.350
IN 0.492 0.205 0.020 0.033 25 0.003 45 0.007 61 0.010 76 0.014
DSM0136203 MM 12.500 6.200 0.350 0.800 84 0.113 130 0.225 151 0.338 160 0.450
IN 0.492 0.244 0.014 0.031 19 0.004 29 0.009 34 0.013 36 0.018 200
DSM0136205 MM 12.500 6.200 0.500 0.850 120 0.088 215 0.175 293 0.263 363 0.350
IN 0.492 0.244 0.020 0.033 27 0.003 49 0.007 66 0.010 82 0.014
DSM0136207 MM 12.500 6.200 0.700 1.000 239 0.075 457 0.150 660 0.225 855 0.300
IN 0.492 0.244 0.028 0.039 54 0.003 103 0.006 149 0.009 193 0.012
DSM0147203 MM 14.000 7.200 0.350 0.800 68 0.113 106 0.225 123 0.338 131 0.450
IN 0.551 0.283 0.014 0.031 15 0.004 24 0.009 28 0.013 29 0.018
DSM0147205 MM 14.000 7.200 0.500 0.900 120 0.100 210 0.200 279 0.300 338 0.400
IN 0.551 0.283 0.020 0.035 27 0.004 47 0.008 63 0.012 76 0.016 200
DSM0147208 MM 14.000 7.200 0.080 1.100 284 0.075 547 0.150 797 0.225 1040 0.300
IN 0.551 0.283 0.031 0.043 64 0.003 124 0.006 180 0.009 235 0.012
DSM0155204 MM 15.000 5.200 0.400 0.950 101 0.138 154 0.275 176 0.413 181 0.550
IN 0.591 0.205 0.016 0.037 23 0.005 35 0.011 40 0.016 41 0.022
DSM0155205 MM 15.000 5.200 0.500 1.000 133 0.125 221 0.250 278 0.375 321 0.500
IN 0.591 0.205 0.020 0.039 30 0.005 50 0.010 63 0.015 72 0.020
DSM0155206 MM 15.000 5.200 0.600 1.050 171 0.113 302 0.225 407 0.338 499 0.450
IN 0.591 0.205 0.024 0.041 39 0.004 68 0.009 92 0.013 113 0.018
DSM0155207 MM 15.000 5.200 0.700 1.100 214 0.100 395 0.200 555 0.300 704 0.400 200
IN 0.591 0.205 0.028 0.043 48 0.004 89 0.008 125 0.012 159 0.016
DSM0156205 MM 15.000 6.200 0.500 1.000 138 0.125 229 0.250 289 0.375 334 0.500
IN 0.591 0.244 0.020 0.039 31 0.005 52 0.010 65 0.015 75 0.022
DSM0156206 MM 15.000 6.200 0.600 1.050 178 0.113 314 0.225 423 0.338 519 0.450
IN 0.591 0.244 0.024 0.041 40 0.004 71 0.009 96 0.013 117 0.018
DSM0156207 MM 15.000 6.200 0.700 1.100 222 0.100 411 0.200 578 0.300 733 0.400
IN 0.591 0.244 0.028 0.043 50 0.004 93 0.008 130 0.012 165 0.016
42
= 0.225 lb.
inches x 25.4 = mm
lbs. X .454 = kg
PART
O/A
NUMBER
O.D. I.D. MATL. HGT [ f = 0.25 h ] [ f = 0.50 h ] [ f = 0.75 h ] [ FLAT f = h ] # Bag
D d t O.H. LOAD P DEFL. f LOAD P DEFL. f LOAD P DEFL. f LOAD P DEFL. f
DSM0158207 MM 15.000 8.200 0.700 1.100 256 0.100 474 0.200 666 0.300 844 0.400
IN 0.591 0.323 0.028 0.043 58 0.004 107 0.008 150 0.012 191 0.016
DSM0158208 MM 15.000 8.200 0.800 1.200 367 0.100 689 0.200 982 0.300 1260 0.400 200
IN 0.591 0.323 0.031 0.047 83 0.004 156 0.008 222 0.012 285 0.016
DSM0168204 MM 16.000 8.200 0.400 0.900 84 0.125 131 0.250 154 0.375 165 0.500 200
IN 0.630 0.323 0.016 0.035 19 0.005 30 0.010 35 0.015 37 0.020 200
DSM0168206 MM 16.000 8.200 0.600 1.050 172 0.113 304 0.225 410 0.338 503 0.450 200
IN 0.630 0.323 0.024 0.041 39 0.004 69 0.009 93 0.013 113 0.018 200
DSM0168207 MM 16.000 8.200 0.700 1.150 254 0.113 461 0.225 637 0.338 798 0.450 200
IN 0.630 0.323 0.028 0.045 57 0.004 104 0.009 144 0.013 180 0.018 200
DSM0168208 MM 16.000 8.200 0.800 1.200 308 0.100 579 0.200 825 0.300 1060 0.400 180
IN 0.630 0.323 0.031 0.047 70 0.004 131 0.008 186 0.012 239 0.016 180
DSM0168209 MM 16.000 8.200 0.900 1.250 363 0.088 697 0.175 1010 0.263 1320 0.350 180
IN 0.630 0.323 0.035 0.049 82 0.003 157 0.007 229 0.010 298 0.014 180
DSM0186204 MM 18.000 6.200 0.400 1.000 85 0.150 126 0.300 139 0.450 137 0.600
IN 0.709 0.244 0.016 0.039 19 0.006 28 0.012 31 0.018 31 0.024
DSM0186205 MM 18.000 6.200 0.500 1.100 130 0.150 206 0.300 245 0.450 267 0.600
IN 0.709 0.244 0.020 0.043 29 0.006 46 0.012 55 0.018 60 0.024
DSM0186206 MM 18.000 6.200 0.600 1.200 191 0.150 317 0.300 400 0.450 462 0.600
IN 0.709 0.244 0.024 0.047 43 0.006 72 0.012 90 0.018 104 0.024
DSM0186207 MM 18.000 6.200 0.700 1.250 236 0.138 414 0.275 553 0.413 672 0.550
IN 0.709 0.244 0.028 0.049 53 0.005 93 0.011 125 0.016 152 0.022
DSM0186208 MM 18.000 6.200 0.800 1.300 286 0.125 523 0.250 726 0.375 912 0.500
IN 0.709 0.244 0.031 0.051 65 0.005 118 0.010 164 0.015 206 0.020
DSM0188205 MM 18.000 8.200 0.500 1.100 140 0.150 222 0.300 265 0.450 288 0.600
IN 0.709 0.323 0.020 0.043 32 0.006 50 0.012 60 0.018 65 0.024 180
DSM0188207 MM 18.000 8.200 0.700 1.250 255 0.138 446 0.275 596 0.413 725 0.550
IN 0.709 0.323 0.028 0.049 57 0.005 101 0.011 135 0.016 164 0.022
DSM0188208 MM 18.000 8.200 0.800 1.300 309 0.125 564 0.250 783 0.375 984 0.500
IN 0.709 0.323 0.031 0.051 70 0.005 127 0.010 177 0.015 222 0.020
DSM0188210 MM 18.000 8.200 1.000 1.400 425 0.100 814 0.200 1180 0.300 1540 0.400
IN 0.709 0.323 0.039 0.055 96 0.004 184 0.008 267 0.012 347 0.016
DSM0189204 MM 18.000 9.200 0.450 1.050 121 0.150 186 0.300 214 0.450 223 0.600
IN 0.709 0.362 0.018 0.041 27 0.006 42 0.012 48 0.018 50 0.024
DSM0189207 MM 18.000 9.200 0.700 1.200 233 0.125 417 0.250 566 0.375 699 0.500
IN 0.709 0.362 0.028 0.047 53 0.005 94 0.010 128 0.015 158 0.020
DSM0189210 MM 18.000 9.200 1.000 1.400 451 0.100 865 0.200 1250 0.300 1630 0.400
IN 0.709 0.362 0.039 0.055 102 0.004 195 0.008 283 0.012 368 0.016
DSM0208206 MM 20.000 8.200 0.600 1.300 214 0.175 342 0.350 412 0.525 453 0.700 175
IN 0.787 0.323 0.024 0.051 48 0.007 77 0.014 93 0.021 102 0.028 175
DSM0208207 MM 20.000 8.200 0.700 1.350 262 0.163 442 0.325 569 0.488 668 0.650 175
IN 0.787 0.323 0.028 0.053 59 0.006 100 0.013 128 0.019 151 0.026 175
DSM0208208 MM 20.000 8.200 0.800 1.400 315 0.150 557 0.300 751 0.450 920 0.600 175
IN 0.787 0.323 0.031 0.055 71 0.006 126 0.012 170 0.018 208 0.024 175
DSM0208209 MM 20.000 8.200 0.900 1.450 374 0.138 685 0.275 954 0.413 1200 0.550 175
IN 0.787 0.323 0.035 0.057 84 0.005 155 0.011 215 0.016 271 0.022 175
DSM0208210 MM 20.000 8.200 1.000 1.550 494 0.138 917 0.275 1290 0.413 1650 0.550 150
IN 0.787 0.323 0.039 0.061 111 0.005 207 0.011 292 0.016 372 0.022 150
DSM0201005 MM 20.000 10.200 0.500 1.150 141 0.163 219 0.325 254 0.488 268 0.650 175
IN 0.787 0.402 0.020 0.045 32 0.006 49 0.013 57 0.019 61 0.026 175
DSM0201008 MM 20.000 10.200 0.800 1.350 304 0.138 547 0.275 748 0.413 929 0.550 175
IN 0.787 0.402 0.031 0.053 69 0.005 123 0.011 169 0.016 210 0.022 175
DSM0201009 MM 20.000 10.200 0.900 1.450 412 0.138 754 0.275 1050 0.413 1320 0.550 150
IN 0.787 0.402 0.035 0.057 93 0.005 170 0.011 237 0.016 299 0.022 150
DSM0201010 MM 20.000 10.200 1.000 1.550 544 0.138 1010 0.275 1430 0.413 1820 0.550 150
IN 0.787 0.402 0.039 0.061 123 0.005 228 0.011 322 0.016 410 0.022 150
DSM0201011 MM 20.000 10.200 1.100 1.550 548 0.113 1050 0.225 1520 0.338 1980 0.450 125
IN 0.787 0.402 0.043 0.061 124 0.004 237 0.009 343 0.013 446 0.018 125
DSM0201012 MM 20.000 10.200 1.250 1.750 890 0.125 1710 0.250 2480 0.375 3220 0.500 100
IN 0.787 0.402 0.049 0.069 201 0.005 385 0.010 559 0.015 727 0.020 100
DSM0201015 MM 20.000 10.200 1.500 1.800 857 0.075 1700 0.150 2520 0.225 3340 0.300 100
IN 0.787 0.402 0.059 0.071 193 0.003 383 0.006 569 0.009 754 0.012 100
DSM0221106 MM 22.500 11.200 0.600 1.400 240 0.200 370 0.400 425 0.600 444 0.800 150
IN 0.886 0.441 0.024 0.055 54 0.008 84 0.016 96 0.024 100 0.310 150
DSM0221108 MM 22.500 11.200 0.800 1.450 306 0.163 533 0.325 707 0.488 855 0.650 150
IN 0.886 0.441 0.031 0.057 69 0.006 120 0.013 160 0.019 193 0.026 150
DSM0221112 MM 22.500 11.200 1.250 1.750 693 0.125 1330 0.250 1930 0.375 2510 0.500 100
IN 0.886 0.441 0.049 0.069 156 0.005 300 0.010 435 0.015 566 0.020 100
43
= 0.225 lb.
inches x 25.4 = mm
lbs. x .454 = kg
O/A
PART
O.D. I.D. MATL. HGT [ f = 0.25 h ] [ f = 0.50 h ] [ f = 0.75 h ] [ FLAT f = h] # Bag
NUMBER
DSM0238207 MM 23.000 8.200 0.700 1.500 279 0.200 448 0.400 544 0.600 602 0.800 150
IN 0.906 0.323 0.028 0.059 63 0.008 101 0.016 123 0.024 136 0.031 150
DSM0238208 MM 23.000 8.200 0.800 1.550 332 0.188 560 0.375 719 0.563 842 0.750 150
IN 0.906 0.323 0.031 0.061 75 0.007 126 0.015 162 0.022 190 0.030 150
DSM0238209 MM 23.000 8.200 0.900 1.600 391 0.175 687 0.350 919 0.525 1120 0.700 150
IN 0.906 0.323 0.035 0.063 88 0.007 155 0.014 207 0.021 253 0.028 150
DSM0238210 MM 23.000 8.200 1.000 1.700 507 0.175 909 0.350 1240 0.525 1540 0.700 125
IN 0.906 0.323 0.039 0.067 115 0.007 205 0.014 280 0.021 347 0.028 125
DSM0231009 MM 23.000 10.200 0.900 1.650 463 0.188 802 0.375 1060 0.563 1270 0.750 150
IN 0.906 0.402 0.035 0.065 105 0.007 181 0.015 239 0.022 287 0.030 150
DSM0231010 MM 23.000 10.200 1.000 1.700 538 0.175 964 0.350 1320 0.525 1630 0.700 125
IN 0.906 0.402 0.039 0.067 122 0.007 218 0.014 297 0.021 368 0.028 125
DSM0231012 MM 23.000 10.200 1.250 1.900 870 0.163 1630 0.325 2310 0.488 2960 0.650 100
IN 0.906 0.402 0.049 0.075 196 0.006 367 0.013 521 0.019 667 0.026 100
DSM0231210 MM 23.000 12.200 1.000 1.600 475 0.150 872 0.300 1220 0.450 1540 0.600 125
IN 0.906 0.480 0.039 0.063 107 0.006 197 0.012 275 0.018 347 0.024 125
DSM0231212 MM 23.000 12.200 1.250 1.850 863 0.150 1630 0.300 2330 0.450 3000 0.600 100
IN 0.906 0.480 0.049 0.073 195 0.006 368 0.012 526 0.018 677 0.024 100
DSM0231215 MM 23.000 12.200 1.500 2.000 1160 0.125 2250 0.250 3300 0.375 4320 0.500 100
IN 0.906 0.480 0.059 0.079 262 0.005 508 0.010 744 0.015 975 0.020 100
DSM0251010 MM 25.000 10.200 1.000 1.750 492 0.188 870 0.375 1170 0.563 1440 0.750 100
IN 0.984 0.402 0.039 0.069 111 0.007 196 0.015 265 0.022 324 0.030 100
DSM0251207 MM 25.000 12.200 0.700 1.600 331 0.225 515 0.450 600 0.675 635 0.900 150
IN 0.984 0.480 0.028 0.063 75 0.009 116 0.018 135 0.027 143 0.035 150
DSM0251209 MM 25.000 12.200 0.900 1.600 367 0.175 644 0.350 862 0.525 1050 0.700 125
IN 0.984 0.480 0.035 0.063 83 0.007 145 0.014 195 0.021 237 0.028 125
DSM0251210 MM 25.000 12.200 1.000 1.800 585 0.200 1020 0.400 1360 0600 1650 0.800 100
IN 0.984 0.480 0.039 0.071 132 0.008 230 0.016 307 0.024 372 0.031 100
DSM0251212 MM 25.000 12.200 1.250 1.950 848 0.175 1570 0.350 2210 0.525 2810 0.700 80
IN 0.984 0.480 0.049 0.077 192 0.007 355 0.014 550 0.021 635 0.029 80
DSM0251215 MM 25.000 12.200 1.500 2.050 1040 0.138 2010 0.275 2930 0.413 3830 0.550 80
IN 0.984 0.480 0.059 0.081 235 0.005 453 0.011 660 0.016 863 0.022 80
DSM0281008 MM 28.000 10.200 0.800 1.750 348 0.238 552 0.475 662 0.713 723 0.950 125
IN 1.102 0.402 0.031 0.069 79 0.009 125 0.019 149 0.028 163 0.037 125
DSM0281010 MM 28.000 10.200 1.000 1.900 512 0.225 872 0.450 1130 0.675 1340 0.900 100
IN 1.102 0.402 0.039 0.075 116 0.009 197 0.018 255 0.027 302 0.035 100
DSM0281012 MM 28.000 10.200 1.250 2.050 736 0.200 1340 0.400 1850 0.600 2320 0.800 80
IN 1.102 0.402 0.049 0.081 166 0.008 302 0.016 418 0.024 524 0.031 80
DSM0281015 MM 28.000 10.200 1.500 2.200 1000 0.175 1900 0.350 2720 0.525 3510 0.700 80
IN 1.102 0.402 0.059 0.087 226 0.007 429 0.014 615 0.021 792 0.028 80
DSM0281210 MM 28.000 12.200 1.000 1.950 590 0.238 992 0.475 1270 0.713 1480 0.950 100
IN 1.102 0.480 0.039 0.077 133 0.009 224 0.019 286 0.028 335 0.037 100
DSM0281212 MM 28.000 12.200 1.250 2.100 844 0.213 1520 0.425 2080 0.638 2590 0.850 80
IN 1.102 0.480 0.049 0.083 190 0.008 343 0.017 470 0.025 585 0.033 80
DSM0281215 MM 28.000 12.200 1.500 2.250 1150 0.188 2160 0.375 3080 0.563 3950 0.750 80
IN 1.102 0.480 0.059 0.089 259 0.007 487 0.015 695 0.022 891 0.030 80
DSM0281408 MM 28.000 14.200 0.800 1.800 435 0.250 681 0.500 801 0.750 859 1.000 125
IN 1.102 0.559 0.031 0.071 98 0.010 154 0.020 181 0.030 194 0.039 125
DSM0281410 MM 28.000 14.200 1.000 1.800 476 0.200 832 0.400 1110 0.600 1340 0.800 100
IN 1.102 0.559 0.039 0.071 108 0.008 188 0.016 250 0.024 303 0.031 100
DSM0281412 MM 28.000 14.200 1.250 2.100 907 0.213 1630 0.425 2240 0.638 2790 0.850 80
IN 1.102 0.559 0.049 0.083 205 0.008 369 0.017 506 0.025 629 0.033 80
DSM0281415 MM 28.000 14.200 1.500 2.150 1030 0.163 1970 0.325 2840 0.488 3680 0.650 80
IN 1.102 0.559 0.059 0.085 233 0.006 445 0.013 641 0.019 831 0.026 80
DSM0311210 MM 31.500 12.200 1.000 2.100 587 0.275 951 0.550 1170 0.825 1310 1.100 100
IN 1.240 0.480 0.039 0.083 132 0.011 215 0.022 263 0.032 295 0.043 100
DSM0311212 MM 31.500 12.200 1.250 2.200 761 0.238 1340 0.475 1810 0.713 2210 0.950 75
IN 1.240 0.480 0.049 0.087 172 0.009 303 0.019 407 0.028 498 0.037 75
DSM0311215 MM 31.500 12.200 1.500 2.350 1030 0.213 1910 0.425 2690 0.638 3410 0.850 70
IN 1.240 0.480 0.059 0.093 233 0.008 432 0.017 607 0.025 770 0.033 70
DSM0311608 MM 31.500 16.300 0.800 1.850 384 0.263 594 0.525 687 0.788 722 1.050 100
IN 1.240 0.642 0.031 0.073 87 0.010 134 0.021 155 0.031 163 0.041 100
DSM0311612 MM 31.500 16.300 1.250 2.150 791 0.225 1410 0.450 1910 0.675 2360 0.900 80
IN 1.240 0.642 0.049 0.085 178 0.009 318 0.018 432 0.027 533 0.035 80
44
= 0.225 lb.
inches x 25.4 = mm
lbs. x .454 = kg
PART O/A
D d t O.H. LOAD P DEFL. f LOAD P DEFL. f LOAD P DEFL. f LOAD P DEFL.f
DSM0311615 MM 31.500 16.300 1.500 2.400 1260 0.225 2310 0.450 3230 0.675 4080 0.900 70
IN 1.240 0.642 0.059 0.094 284 0.009 522 0.018 729 0.027 920 0.035 70
DSM0311617 MM 31.500 16.300 1.750 2.450 1390 0.175 2670 0.350 3870 0.525 5040 0.700 60
IN 1.240 0.642 0.069 0.096 314 0.007 602 0.014 874 0.021 1140 0.028 60
DSM0311620 MM 31.500 16.300 2.000 2.750 2200 0.188 4240 0.375 6170 0.563 8050 0.750 60
IN 1.240 0.642 0.079 0.108 496 0.007 957 0.015 1390 0.022 1820 0.030 60
DSM0341210 MM 34.000 12.300 1.000 2.250 637 0.313 998 0.625 1170 0.938 1260 1.250 90
IN 1.339 0.484 0.039 0.089 144 0.012 225 0.025 265 0.037 284 0.049 90
DSM0341212 MM 34.000 12.300 1.250 2.350 815 0.275 1400 0.550 1820 0.825 2160 1.100 70
IN 1.339 0.484 0.049 0.093 184 0.011 315 0.022 410 0.032 488 0.043 70
DSM0341215 MM 34.000 12.300 1.500 2.500 1100 0.250 1980 0.500 2730 0.750 3400 1.000 60
IN 1.339 0.484 0.059 0.098 248 0.010 447 0.020 615 0.030 767 0.039 60
DSM0341412 MM 34.000 14.300 1.250 2.400 913 0.288 1550 0.575 1990 0.863 2350 1.150 60
IN 1.339 0.563 0.049 0.094 206 0.011 349 0.023 450 0.034 530 0.045 60
DSM0341415 MM 34.000 14.300 1.500 2.550 1220 0.263 2190 0.525 2990 0.788 3700 1.050 60
IN 1.339 0.563 0.059 0.100 276 0.010 495 0.021 675 0.031 836 0.041 60
DSM0341615 MM 34.000 16.300 1.500 2.550 1290 0.263 2310 0.525 3160 0.788 3910 1.050 60
IN 1.339 0.642 0.059 0.100 291 0.010 522 0.021 712 0.031 882 0.041 60
DSM0341620- MM 34.000 16.300 2.000 2.850 2100 0.213 4000 0.425 5780 0.638 7500 0.850 50
IN 1.339 0.642 0.079 0.112 473 0.008 904 0.017 1310 0.025 1690 0.033 50
DSM0351809 MM 35.500 18.300 0.900 2.050 458 0.288 712 0.575 832 0.863 884 1.150 100
IN 1.398 0.720 0.035 0.081 103 0.011 161 0.023 188 0.034 200 0.045 100
DSM0351812 MM 35.500 18.300 1.250 2.250 731 0.250 1280 0.500 1700 0.750 2060 1.000 60
IN 1.398 0.720 0.049 0.089 165 0.010 288 0.020 383 0.030 465 0.039 60
DSM0351820 MM 35.500 18.300 2.000 2.800 1860 0.200 3580 0.400 5190 0.600 6750 0.800 50
IN 1.398 0.720 0.079 0.110 421 0.008 807 0.016 1170 0.024 1520 0.031 50
DSM0401412 MM 40.000 14.300 1.250 2.650 904 0.350 1460 0.700 1780 1.050 1980 1.400 50
IN 1.575 0.563 0.049 0.104 204 0.014 329 0.028 402 0.041 448 0.055 50
DSM0401415 MM 40.000 14.300 1.500 2.750 1110 0.313 1930 0.625 2550 0.938 3060 1.250 50
IN 1.575 0.563 0.059 0.108 251 0.012 436 0.025 575 0.037 691 0.049 50
DSM0401420 MM 40.000 14.300 2.000 3.050 1800 0.263 3360 0.525 4770 0.788 6100 1.050 40
IN 1.575 0.563 0.079 0.120 406 0.010 759 0.021 1080 0.031 1380 0.041 40
DSM0401615 MM 40.000 16.300 1.500 2.800 1220 0.325 2100 0.650 2750 0.975 3280 1.300 45
IN 1.575 0.642 0.059 0.110 276 0.013 475 0.026 621 0.038 741 0.051 45
DSM0401620 MM 40.000 16.300 2.000 3.100 1970 0.275 3660 0.550 5170 0.825 6580 1.100 40
IN 1.575 0.642 0.079 0.122 445 0.011 827 0.022 1170 0.032 1490 0.043 40
DSM0401820 MM 40.000 18.300 2.000 3.150 2180 0.288 4030 0.575 5660 0.863 7170 1.150 40
IN 1.575 0.720 0.079 0.124 492 0.011 910 0.023 1280 0.034 1620 0.045 40
DSM0402010 MM 40.000 20.400 1.000 2.300 565 0.325 876 0.650 1020 0.975 1070 1.300 50
IN 1.575 0.803 0.039 0.091 128 0.013 198 0.026 229 0.038 242 0.051 50
DSM0402015 MM 40.000 20.400 1.500 2.650 1110 0.288 1950 0.575 2620 0.863 3200 1.150 45
IN 1.575 0.803 0.059 0.104 250 0.011 441 0.023 592 0.034 723 0.045 45
DSM0402020 MM 40.000 20.400 2.000 3.100 2180 0.275 4040 0.550 5700 0.825 7260 1.100 40
IN 1.575 0.803 0.079 0.122 491 0.011 912 0.022 1290 0.032 1640 0.043 40
DSM0402022 MM 40.000 20.400 2.250 3.150 2340 0.225 4480 0.450 6500 0.675 8460 0.900 35
IN 1.575 0.803 0.089 0.124 527 0.009 1010 0.018 1470 0.027 1910 0.035 35
DSM0402025 MM 40.000 20.400 2.500 3.450 3350 0.238 6450 0.475 9390 0.713 12200 0.950 35
IN 1.575 0.803 0.098 0.136 756 0.009 1460 0.019 2120 0.028 2760 0.037 35
DSM0452212 MM 45.000 22.400 1.250 2.850 1040 0.400 1620 0.800 1890 1.200 2010 1.600 35
IN 1.772 0.882 0.049 0.112 235 0.016 366 0.031 427 0.047 453 0.063 35
DSM0452217 MM 45.000 22.400 1.750 3.050 1520 0.325 2700 0.650 3650 0.975 4480 1.300 30
IN 1.772 0.882 0.069 0.120 344 0.013 610 0.026 823 0.038 1010 0.051 30
DSM0452225 MM 45.000 22.400 2.500 3.500 2770 0.250 5320 0.500 7720 0.750 10000 1.000 30
IN 1.772 0.882 0.098 0.138 626 0.010 1200 0.020 1740 0.030 2270 0.039 30
DSM0501812 MM 50.000 18.400 1.250 2.850 757 0.400 1180 0.800 1370 1.200 1460 1.600 30
IN 1.969 0.724 0.049 0.112 171 0.016 266 0.031 310 0.047 329 0.063 30
DSM0501815 MM 50.000 18.400 1.500 3.300 1380 0.450 2180 0.900 2610 1.350 2840 1.800 30
IN 1.969 0.724 0.059 0.130 311 0.018 493 0.035 588 0.053 640 0.071 30
DSM0501820 MM 50.000 18.400 2.000 3.500 1920 0.375 3390 0.750 4570 1.125 5600 1.500 25
IN 1.969 0.724 0.079 0.138 423 0.015 766 0.030 1030 0.044 1260 0.059 25
DSM0501825 MM 50.000 18.400 2.500 4.100 3700 0.400 6730 0.800 9320 1.200 11700 1.600 25
IN 1.969 0.724 0.098 0.161 836 0.016 1520 0.031 2100 0.047 2630 0.063 25
DSM0501830 MM 50.000 18.400 3.000 4.400 5040 0.350 9550 0.700 13700 1.050 17600 1.400 20
IN 1.969 0.724 0.118 0.173 1140 0.014 2150 0.028 3090 0.041 3980 0.055 20
DSM0502020 MM 50.000 20.400 2.000 3.500 1970 0.375 3480 0.750 4690 1.125 5750 1.500 25
IN 1.969 0.803 0.079 0.138 444 0.015 785 0.030 1060 0.044 1300 0.059 25
DSM0502025 MM 50.000 20.400 2.500 3.850 3010 0.338 5600 0.675 7920 1.013 10100 1.350 25
IN 1.969 0.803 0.098 0.152 679 0.013 1260 0.027 1790 0.040 2280 0.053 25
45
= 0.225 lb.
inches x 25.4 = mm
lbs. x .454 = kg
PART O/A
DSM0502220 MM 50.000 22.400 2.000 3.600 2250 0.400 3920 0.800 5220 1.200 6330 1.600 25
IN 1.969 0.882 0.079 0.142 507 0.016 886 0.031 1180 0.047 1430 0.063 25
DSM0502225 MM 50.000 22.400 2.500 3.900 3260 0.350 6040 0.700 8510 1.050 10800 1.400 25
IN 1.969 0.882 0.098 0.154 736 0.014 1360 0.028 1920 0.041 2440 0.055 25
MM 50.000 25.400 1.250 2.850 854 0.400 1330 0.800 1550 1.200 1650 1.600 30
DSM0502512 IN 1.969 1.000 0.049 0.112 193 0.016 300 0.031 350 0.047 371 0.063 30
DSM0502515 MM 50.000 25.400 1.500 3.100 1240 0.400 2030 0.800 2510 1.200 2840 1.600 30
IN 1.969 1.000 0.059 0.122 280 0.016 458 0.031 567 0.047 642 0.063 30
DSM0502520 MM 50.000 25.400 2.000 3.400 1950 0.350 3490 0.700 4760 1.050 5900 1.400 25
IN 1.969 1.000 0.079 0.134 440 0.014 788 0.028 1070 0.041 1330 0.055 25
MM 50.000 25.400 2.500 3.900 3470 0.350 6440 0.700 9060 1.050 11500 1.400 25
DSM0502525 IN 1.969 1.000 0.098 0.154 784 0.014 1450 0.028 2050 0.041 2600 0.055 25
DSM0502530 MM 50.000 25.400 3.000 4.100 4250 0.275 8210 0.550 12000 0.825 15600 1.100 20
IN 1.969 1.000 0.118 0.161 960 0.011 1850 0.022 2700 0.032 3530 0.043 20
DSM0562815 MM 56.000 28.500 1.500 3.450 1460 0.488 2260 0.975 2620 1.463 2770 1.950 25
IN 2.205 1.122 0.059 0.136 329 0.019 510 0.038 592 0.058 624 0.077 25
DSM0562820 MM 56.000 28.500 2.000 3.600 1910 0.400 3340 0.800 4440 1.200 5380 1.600 20
IN 2.205 1.122 0.079 0.142 431 0.016 753 0.031 1000 0.047 1210 0.063 20
DSM0562830 MM 56.000 28.500 3.000 4.300 4140 0.325 7900 0.650 11400 0.975 14800 1.300 15
IN 2.205 1.122 0.118 0.169 935 0.013 1780 0.026 2570 0.038 3330 0.051 15
DSM0602020 MM 60.000 20.500 2.000 4.100 2320 0.525 3800 1.050 4730 1.575 5380 2.100 20
IN 2.362 0.807 0.079 0.161 523 0.021 858 0.041 1070 0.062 1210 0.083 20
DSM0602025 MM 60.000 20.500 2.500 4.300 3020 0.450 5380 0.900 7300 1.350 9010 1.800 15
IN 2.362 0.807 0.098 0.169 681 0.018 1210 0.035 1650 0.053 2030 0.071 15
DSM0602030 MM 60.000 20.500 3.000 4.700 4450 0.425 8230 0.850 11600 1.275 14700 1.700 15
IN 2.362 0.807 0.118 0.185 1000 0.017 1860 0.033 2610 0.050 3320 0.067 15
DSM0602525 MM 60.000 25.500 2.500 4.400 3450 0.475 6080 0.950 8180 1.425 10000 1.900 15
IN 2.362 1.004 0.098 0.173 778 0.019 1370 0.037 1850 0.056 2260 0.075 15
DSM0602530 MM 60.000 25.500 3.000 4.650 4500 0.413 8350 0.825 11800 1.238 15000 1.650 15
IN 2.362 1.004 0.118 0.183 1010 0.016 1980 0.032 2660 0.049 3390 0.065 15
DSM0603025 MM 60.000 30.500 2.500 4.300 3450 0.450 6150 0.900 8348 1.350 10300 1.800 15
IN 2.362 1.201 0.098 0.169 778 0.018 1390 0.035 1880 0.053 2320 0.071 15
DSM0503030 MM 60.000 30.500 3.000 4.700 5080 0.425 9410 0.850 13200 1.275 16800 1.700 15
IN 2.362 1.201 0.118 0.185 1150 0.017 2120 0.033 2990 0.050 3790 0.067 15
DSM0603035 MM 60.000 30.500 3.500 5.000 6590 0.375 12600 0.750 18200 1.125 23500 1.500 15
IN 2.362 1.201 0.138 0.197 1490 0.015 2840 0.030 4100 0.044 5310 0.059 15
DSM0633118 MM 63.000 31.000 1.800 4.150 2360 0.588 3660 1.175 4240 1.763 4460 2.350 15
IN 2.480 1.220 0.071 0.163 534 0.023 826 0.046 957 0.069 1010 0.093 15
DSM0633125 MM 63.000 31.000 2.500 4.250 2940 0.438 5270 0.875 7190 1.313 8900 1.750 15
IN 2.480 1.220 0.098 0.167 664 0.017 1190 0.034 1620 0.052 2010 0.069 15
DSM0633130 MM 63.000 31.000 3.000 4.800 4890 0.450 8980 0.900 12500 1.350 15800 1.800 10
IN 2.480 1.220 0.118 0.189 1100 0.018 2030 0.035 2830 0.053 3570 0.071 10
DSM0633135 MM 63.000 31.000 3.500 4.900 5400 0.350 10400 0.700 15000 1.050 19500 1.400 10
IN 2.490 1.220 0.138 0.193 1220 0.014 2340 0.028 3390 0.041 4410 0.055 10
DSM0702520 MM 70.000 25.500 2.000 4.500 2410 0.625 3770 1.250 4440 1.875 4760 2.500 10
IN 2.756 1.004 0.079 0.177 544 0.025 851 0.049 1000 0.074 1070 0.098 10
MM 70.000 30.500 2.500 4.900 3760 0.600 6300 1.200 8030 1.800 9360 2.400 10
DSM0703025
IN 2.756 1.201 0.098 0.193 848 0.024 1420 0.047 1810 0.071 2110 0.094 10
MM 70.000 30.500 3.000 5.100 4680 0.525 8380 1.050 11400 1.575 14200 2.100 10
DSM0703030 IN 2.756 1.201 0.118 0.201 1060 0.021 1890 0.041 2580 0.062 3190 0.083 10
DSM0703530 MM 70.000 35.500 3.000 5.100 5030 0.525 9010 1.050 12300 1.575 15200 2.100 10
IN 2.756 1.398 0.118 0.201 1130 0.021 2030 0.041 2770 0.062 3440 0.083 10
DSM0703540 MM 70.000 35.500 4.000 5.800 8760 0.450 16600 0.900 23900 1.350 30900 1.800 6
IN 2.756 1.398 0.257 0.228 1980 0.018 3750 0.035 5400 0.053 6980 0.071 6
MM 70.000 40.500 4.000 5.600 8390 0.400 16100 0.800 23400 1.200 30400 1.600 6
DSM0704040 IN 2.756 1.594 0.157 0.220 1890 0.016 3360 0.031 5270 0.047 6860 0.063 6
DSM0704050 MM 70.000 40.500 5.000 6.000 11500 0.300 22700 0.600 33700 0.900 44500 1.200 5
IN 2.756 1.594 0.197 0.244 2610 0.012 5130 0.024 7600 0.035 10000 0.047 5
MM
DSM0713620 IN 71.000 36.000 2.000 4.600 2860 0.650 4430 1.300 5140 1.950 5430 2.600 10
2.795 1.417 0.079 0.181 646 0.026 1000 0.051 1160 0.077 1220 0.102 10
DSM0713625 MM 71.000 36.000 2.500 4.500 2890 0.500 5050 1.000 6730 1.500 8150 2.000 10
IN 2.795 1.417 0.098 0.177 653 0.020 1140 0.039 1520 0.059 1840 0.079 10
MM 71.000 36.000 4.000 5.600 7380 0.400 14200 0.800 20500 1.200 26700 1.600 6
DSM0713640 IN 2.795 1.417 0.157 0.220 1670 0.016 3200 0.031 4640 0.047 6030 0.063 6
DSM0803125 MM 80.000 31.000 2.500 5.300 3680 0.700 5930 1.400 7240 2.100 8070 2.800 8
IN 3.150 1.220 0.098 0.209 830 0.028 1340 0.055 1630 0.083 1820 0.110 8
MM 80.000 31.000 3.000 5.500 4530 0.625 7850 1.250 10400 1.875 12500 2.500 8
DSM0803130 IN 3.150 1.220 0.118 0.217 1020 0.025 1770 0.049 2340 0.074 2810 0.098 8
46
= 0.225 lb.
inches x 25.4 = mm
lbs. x .454 = kg
PART O/A
DSM0803140 MM 80.000 31.000 4.000 6.100 7320 0.525 13700 1.050 19400 1.575 24800 2.100 5
IN 3.150 1.220 0.157 0.240 1650 0.021 3090 0.041 4380 0.062 5600 0.083 5
DSM0803630 MM 80.000 36.000 3.000 5.700 5400 0.675 9200 1.350 11900 2.025 14100 2.700 8
IN 3.150 1.417 0.118 0.224 1220 0.027 2080 0.053 2690 0.080 3180 0.106 8
DSM0803640 MM 80.000 36.000 4.000 6.200 8160 0.550 15200 1.100 21400 1.650 27200 2.200 5
IN 3.150 1.417 0.157 0.224 1840 0.022 3420 0.043 4830 0.065 6150 0.087 5
DSM0804122 MM 80.000 41.000 2.250 5.200 3700 0.738 5720 1.475 6610 2.213 6950 2.950 8
IN 3.150 1.614 0.089 0.205 835 0.029 1290 0.058 1490 0.087 1570 0.116 8
DSM0804130 MM 80.000 41.000 3.000 5.300 4450 0.575 7840 1.150 10500 1.725 12800 2.300 8
IN 3.150 1.614 0.118 0.209 1000 0.023 1770 0.045 2370 0.068 2900 0.091 8
DSM0804140 MM 80.000 41.000 4.000 6.200 8730 0.550 16200 1.100 22900 1.650 29100 2.200 5
IN 3.150 1.614 0.157 0.244 1970 0.022 3660 0.043 5160 0.065 6570 0.087 5
DSM0804150 MM 80.000 41.000 5.000 6.700 11800 0.425 22900 0.850 33600 1.275 44000 1.700 4
IN 3.150 1.614 0.197 0.264 2670 0.017 5180 0.033 7580 0.050 9920 0.067 4
DSM0904625 MM 90.000 46.000 2.500 5.700 4230 0.800 6580 1.600 7680 2.400 8160 3.200 6
IN 3.543 1.811 0.098 0.224 955 0.031 1490 0.063 1730 0.094 1840 0.126 6
DSM0904635 MM 90.000 46.000 3.500 6.000 5840 0.625 10400 1.250 14200 1.874 17500 2.500 6
IN 3.543 1.811 0.138 0.236 1320 0.025 2350 0.049 3200 0.074 3950 0.098 6
DSM0904650 MM 90.000 46.000 5.000 7.000 11300 0.500 21600 1.000 31400 1.500 40800 2.000 4
IN 3.543 1.811 0.197 0.276 2540 0.020 4880 0.039 7080 0.059 9210 0.079 4
DSM1004140 MM 100.000 41.000 4.000 7.200 8710 0.800 15200 1.600 20300 2.400 24500 3.200 4
IN 3.937 1.614 0.157 0.283 1970 0.031 3440 0.063 4570 0.094 5540 0.126 4
DSM1004150 MM 100.000 41.000 5.000 7.750 12300 0.688 22900 1.375 32400 2.063 41200 2.750 3
IN 3.937 1.614 0.197 0.305 2790 0.027 5180 0.054 7300 0.081 9300 0.108 3
DSM1005127 MM 100.000 51.000 2.700 6.200 4780 0.875 7410 1.750 8610 2.625 9090 3.500 5
IN 3.937 2.008 0.106 0.244 1080 0.034 1670 0.069 1940 0.103 2050 0.138 5
DSM1005135 MM 100.000 51.000 3.500 6.300 5620 0.700 9820 1.400 13100 2.100 15800 2.800 5
IN 3.937 2.008 0.138 0.248 1270 0.028 2220 0.055 2950 0.083 3580 0.110 5
DSM1005140 MM 100.000 51.000 4.000 7.000 8760 0.750 15300 1.500 20700 2.250 25300 3.000 4
IN 3.937 2.008 0.157 0.276 1960 0.030 3460 0.059 4670 0.089 5720 0.118 4
DSM1005150 MM 100.000 51.000 5.000 7.800 13900 0.700 25800 1.400 36300 2.100 46200 2.800 3
IN 3.937 2.008 0.197 0.307 3140 0.028 5830 0.055 8200 0.083 10400 0.110 3
DSM1005160 MM 100.000 51.000 6.000 8.200 17100 0.550 32900 1.100 48000 1.650 62700 2.200 2
IN 3.937 2.008 0.236 0.323 3850 0.022 7430 0.043 10800 0.065 14200 0.087 2
DSM1125730 MM 112.000 57.000 3.000 6.900 5830 0.975 9040 1.950 10500 2.925 11100 3.900 3
IN 4.409 2.244 0.118 0.272 1320 0.038 2040 0.077 2370 0.115 2500 0.154 3
DSM1125740 MM 112.000 57.000 4.000 7.200 7640 0.800 13300 1.600 17800 2.400 21500 3.200 3
IN 4.409 2.244 0.157 0.283 1720 0.031 3010 0.063 4010 0.094 4860 0.126 3
DSM1125760 MM 112.000 57.000 6.000 8.500 15800 0.625 30200 1.250 43700 1.875 56700 2.500 2
IN 4.409 2.224 0.236 0.335 3570 0.025 6820 0.049 9870 0.074 12800 0.098 2
DSM1254140 MM 125.000 41.000 4.000 8.200 8500 1.050 13900 2.100 17300 3.150 19700 4.200 3
IN 4.921 1.614 0.157 0.323 1920 0.041 3150 0.083 3920 0.124 4450 0.165 3
DSM1255140 MM 125.000 51.000 4.000 8.500 10100 1.125 16300 2.250 19800 3.375 22100 4.500 3
IN 4.921 2.008 0.157 0.335 2280 0.044 3670 0.089 4470 0.133 4980 0.177 3
DSM1255150 MM 125.000 51.000 5.000 8.900 13100 0.975 22900 1.950 30700 2.925 37300 3.900 2
IN 4.921 2.008 0.197 0.350 2950 0.038 5180 0.077 6920 0.115 8430 0.154 2
DSM1255160 MM 125.000 51.000 6.000 9.400 17000 0.850 31500 1.700 44300 2.550 56300 3.400 2
IN 4.921 2.008 0.236 0.370 3840 0.033 7110 0.067 10000 0.100 12700 0.134 2
DSM1256150 MM 125.000 61.000 5.000 9.000 14600 1.000 25500 2.000 34000 3.000 41200 4.000 2
IN 4.921 2.402 0.197 0.354 3300 0.039 5760 0.079 7670 0.118 9290 0.157 2
DSM1256160 MM 125.000 61.000 6.000 9.600 19800 0.900 36300 1.800 50700 2.700 64000 3.600 2
IN 4.921 2.402 0.236 0.378 4470 0.035 8200 0.071 11400 0.106 14500 0.142 2
DSM1256180 MM 125.000 61.000 8.000 10.900 33200 0.725 64100 1.450 93600 2.175 122000 2.900 2
IN 4.921 2.402 0.315 0.429 7490 0.029 14500 0.057 21100 0.086 27600 0.114 2
DSM1256435 MM 125.000 64.000 3.500 8.000 8510 1.125 13200 2.250 15400 3.375 16300 4.500 3
IN 4.921 2.520 0.138 0.315 1920 0.044 2990 0.089 3480 0.133 3690 0.177 3
DSM1256450 MM 125.000 64.000 5.000 8.500 12200 0.875 21900 1.750 29900 2.625 37000 3.500 3
IN 4.921 2.520 0.197 0.335 2760 0.034 4950 0.069 6750 0.103 8360 0.138 3
DSM1256480 MM 125.000 64.000 8.000 10.600 30100 0.650 58600 1.300 85900 1.950 113000 2.600 3
IN 4.921 2.520 0.315 0.417 6800 0.026 13200 0.051 19400 0.077 25400 0.102 3
DSM1257160 MM 125.000 71.000 6.000 9.300 19500 0.825 36300 1.650 51200 2.475 65200 3.300 3
IN 4.921 2.795 0.236 0.366 4410 0.032 8190 0.065 11600 0.097 14700 0.130 3
DSM1257180 MM 125.000 71.000 8.000 10.400 29800 0.600 58100 1.200 85500 1.800 112000 2.400 3
IN 4.921 2.795 0.315 0.409 6720 0.024 13100 0.047 19300 0.071 25400 0.094 3
DSM1257199 MM 125.000 71.000 10.000 11.800 42000 0.450 83300 0.900 124000 1.350 165000 1.800 2
IN 4.921 2.795 0.394 0.465 9490 0.018 18800 0.035 28000 0.053 37200 0.071 2
47
Committed to Quality & Customer Satisfaction
Anchor Lamina is committed to be the customer

focused world-class supplier of choice to the metal-
working and plastics forming industry.
We will help our customers to compete globally by

providing innovative and value added products and
services.
Anchor Lamina Contacts Preferred Business Partners
Lamina Components Ajacs Die Sales Corp.

38505 Country Club Drive Suite 200 Grand Rapids, MI; Tel: 800-968-6868
Farmington Hills, MI USA 48331
Tel: 248-489-9122, 800-652-6462; Fax: 248-553-6842 Clark & Osborne
E-mail: [email protected] Indianapolis, IN; Tel: 800-752-5817
Dayne Supply
Anchor Die Sets Ontario, CA, Tel: 800-289-6387
2590 Ouellette Avenue, Windsor, ON, Canada N8X 1L7
Tel: 519-966-4431, 800-265-5007; Fax: 519-966-3594 R.F. Flood Industrial Supply Corp.
E-mail: [email protected] Ivyland, PA, Tel: 800-235-9950
1450 Alphonse D-Roy, Montreal, QC, Canada H1W 2K8 T.R. Goldsmith
Tel: 514-525-5560, 800-263-5560; Fax: 514-525-7835 Tonawanda, NY, Tel: 800-252-2501
E-mail: [email protected]
IPSCO Corp.
1200 Lakeshore Road East, Mississauga, ON, Canada L5E 1E9 Attleboro, MA; Tel: 800-229-4044
Tel: 905-274-3448, 800-268-5230; Fax: 905-274-7303
E-mail: [email protected] Manufacturers Equipment & Supply
Flint, MI; Tel: 800-373-2173
311 Pinebush Road, Cambridge, ON, Canada N1T 1B2
Tel: 519-740-3060, 800-265-7842 (Canada only); Fax: 519-740-8213 Matis Inc.
E-mail: [email protected] Chicago Ridge, IL; Tel: 708-425-7100
95 East Ten Mile Road, Madison Heights, MI USA 48071 Matzka Inc.
Tel: 248-547-5910, 800-543-3790; Fax: 248-547-5918, 800-963-0400 Warren, MI; Tel: 586-755-6363
Scott Special Tools, Inc.
4300 40th Street, S.E., Kentwood, MI USA 49512 St. Charles, MO; Tel: 800-638-7277
Tel: 616-949-8700, 888-526-2467; Fax: 616-949-9580
E-mail: [email protected] E.L. Simeth Co., Inc.
Milwaukee, WI; Tel: 800-837-9270
Reliance Fabrications Sup-R-Die

95 Lyon Avenue North, Tilbury, ON, Canada N0P 2L0 Cleveland, OH; Tel: 800-821-9194
Tel: 519-682-0470, 800-265-5295; Fax: 519-682-3616
www.anchorlamina.com
017-0703-5m

Spring Cat

Uploaded by

Copyright:

Available Formats

Spring Cat

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Spring Cat

Uploaded by

Copyright:

Available Formats

Spring Products

Wherever motion takes place in dies, molds or machin-

DIE SPRINGS At Lamina, we have long believed that Raymond Die

Anchor Lamina Mission

To be the customer focused world class supplier of choice

We will help our customers to compete globally by provid-

Please check our website

CORRECT DIE SPRING USAGE

DONT... alter a die spring by cutting off

spring failure and potential die damage.

MAXIMUM DEFLECTION 30%

1.00 25 H-12 208.00 312.00 0.15 416.00 0.20 624.00 0.30 50

MAXIMUM DEFLECTION 25%

1.50 38 XH-13 160.00 360.00 0.23 480.00 0.30 600.00 0.38 50

STANDARD TOLERANCES FOR FREE LENGTHS

5 to 7.999 +.187 10 to 12 +.375

LIGHT DUTY DIE SPRINGS METRIC ISO SPECIFICATION SERIES GREEN

LIGHT DUTY DIE SPRINGS METRIC ISO SPECIFICATION SERIES GREEN

MEDIUM DUTY DIE SPRINGS METRIC ISO SPECIFICATION SERIES BLUE

MEDIUM DUTY DIE SPRINGS METRIC ISO SPECIFICATION SERIES BLUE

HEAVY DUTY DIE SPRINGS METRIC ISO SPECIFICATION SERIES RED

HEAVY DUTY DIE SPRING METRIC ISO SPECIFICATION SERIES RED

1 1-5/32 1.105 9/16

1-1/4 1-13/32 1.355 3/4

1-1/2 1-21/32 1.605 31/32

2 2-5/32 2.105 1-3/8

3/4 1" 1-1/4" 1-1/2" 2"

ROUND WIRE DIE FIXTURE SPRINGS

Specials Quoted Upon Request 21

22 Specials Quoted Upon Request

Order by part number

EXTENSION SPRINGS STEEL FIXTURE

EXTENSION SPRING ASSORTMENT

GENERAL MAINTENANCE ASSORTMENT #020-819-1

105 MIDGET SPRINGS ASSORTMENT NO. 020-081

For the small compression spring requirements, these

300 COMPRESSION SPRINGS ASSORTMENT NO. 020-802

Like the above compression kit, only extension springs.

300 EXTENSION SPRINGS ASSORTMENT NO. 020-803

SQUARE WIRE CARBON STEEL DIE & FIXTURE SPRINGS

Temperatures, many of our compounds stay flexible at

Heat build-up, due to internal friction (hysteresis effect), is

Operating Speed & % of Deflection,

Intermittent -- Up to 700 strokes per hour -- up to 25%

Continuous -- Up to 12,000 strokes per hour -- up to 15%

Lathe Cutting -- Use H.S.S. tool bits with positive rake of

L = Length W = Width r = radius h = height d = diameter

* Shape Factor (S.F.) * Convert P.S.I. to load pounds

EXAMPLE: How much pressure will be required to deflect a 6 x 6 x 1 slab by .150?

LAMI-FLEX SHEET, SLAB, ROD SAMPLE PRESSURES

PART OUTSIDE FITS LENGTH LOAD LOAD POUNDS REQUIRED TO DEFLECT

95A Durometer Product is Blue 31

PART OUTSIDE FITS LENGTH LOAD LOAD POUNDS REQUIRED TO DEFLECT

Medium Duty LAMI-FLEX SPRINGS

32 95A Durometer Product is Blue

PART OUTSIDE FITS LENGTH LOAD LOAD POUNDS REQUIRED TO DEFLECT

LFM25012-275 2-3/4 1550 .1375 .2750 .4125

LFM25015-275 2-3/4 1860 .1375 .2750 .4125

95A Durometer Product is Blue 33