MV Elements

Modular Fenders V Fenders

MI Elements

Section 2

Trelleborg Marine Systems

www.trelleborg.com/marine
Ref. M1100-S02-V1.1-EN
22

MV
ELEMENTS
MV-elements are the foundation
of many fender systems. These
modular units are compression
moulded from a high performance
polymer which resists attack from
ultraviolet light, ozone and immersion
in seawater for long service life and
low maintenance.
Available in a full range of sizes,
the geometry of the MV-element has
been optimised for maximum energy
absorption per unit volume of rubber
combined with a low reaction force.
Fully encapsulated steel mounting
plates are vulcanised inside the
MV-element to allow easy fixing.
Bolts are located centrally on the
base flanges to reduce stresses,
but being recessed into pockets
the fixings are well protected from
damage.

Features
B Modular design system
B Many standard sizes
B High performance geometry
B Recessed fixings
B Long life, low maintenance

Applications
All vessel types which use the
following systems:
B Fender piles
B V-fenders
B Multiple fenders
B Pivot pillars
B Parallel Motion (Torsion Arm)

Standard manufacturing and performance tolerances apply (see pages 1236 to 1239)

M1100-S02-V1.1-EN. Trelleborg AB, 2007

 23

MV ELEMENT

Each fender generation

provides more energy for
the same reaction force.
Reaction

ENERGY

Deflection

Fender Evolution
Ships have grown larger so have the demands on fenders. A century ago MV-element
timber (1st Generation) was cheap and worked adequately for the small
vessels of the day. Old tyres (2nd Generation) were abundant and softer but
required expensive maintenance and absorbed little energy.
Cylindricals (3rd Generation) were the first purpose designed fenders,
gaining popularity some 50 years ago, but inefficient use of rubber and low
performance by todays standards makes them costly. Arch and simple V-fender
buckling fenders (4th Generation) had better performance and integrated the
rubber with steel fixing plates.

5th Generation Fenders

MV-elements are 5th Generation fenders. With refined geometry the rubber
has a characteristic double-buckle S shape. This gives the MV-element a
greater deflection for the same reaction so it absorbs more energy than all
previous generations with less material.

System fender
Modular Design
MV-elements are modular so can be installed horizontally or vertically, close
together or further apart, with the V facing towards or away from the panel.
A and B compounds can be mixed or different lengths used allowing
almost limitless permutations and giving the designer greater control on how
an MV-system behaves when impacted.

Standard manufacturing and performance tolerances apply (see pages 1236 to 1239)

M1100-S02-V1.1-EN. Trelleborg AB, 2007

24

MV300 elements up to 3000mm available on request.

MV ELEMENT
Dimensions

L B C D E F G J T Anchor Holes Weight

600 2+2 27
900 150 300 150 300 94 93 47 17 M20 3+3 41
MV300
1200 4+4 54
1500 5+5 68
750 125 125 2+2 50
1000 250 250 2+2 66
1500 250 250 3+3 99
MV400 500 500 125 124 63 17 M24
2000 250 250 4+4 132
2500 250 250 5+5 165
3000 250 250 6+6 198
750 125 125 2+2 84
1000 2+2 111
1500 3+3 167
MV500 500 500 158 142 87 20 M30
2000 250 250 4+4 222
2500 5+5 278
3000 6+6 334
750 125 125 2+2 100
MV550 1000 500 500 172 170 87 20 M30 2+2 132
250 250
1500 3+3 200
750 125 125 2+2 115
MV600 1000 500 500 188 199 87 20 M30 2+2 153
250 250
1500 3+3 230
750 125 125 2+2 180
MV750 1000 500 500 235 230 118 26 M36 2+2 239
250 250
1500 3+3 359
800 150 150 2+2 214
1000 2+2 268
MV800 500 500 250 240 129 26 M36
1500 250 250 3+3 402
2000 4+4 536
800 150 150 2+2 346
850 175 175 2+2 368
900 200 200 2+2 389
950 225 225 2+2 411
1000 250 250 2+2 432
MV1000 1050 275 500 275 500 322 310 162 31 M42 2+2 454
1100 300 300 2+2 476
1150 325 325 2+2 497
1200 350 350 2+2 519
1500 3+3 648
250 250
2000 4+4 864

Standard manufacturing and performance tolerances apply (see pages 1236 to 1239)

M1100-S02-V1.1-EN. Trelleborg AB, 2007

 25

MV ELEMENT
Dimensions

L B C D E F G J T Anchor Holes Weight

800 150 150 2+2 511
850 175 175 2+2 543
900 200 200 2+2 575
950 225 225 2+2 607
1000 250 250 2+2 639
1050 275 275 2+2 671
MV1250 500 500 401 388 202 36 M48
1100 300 300 2+2 703
1150 325 325 2+2 735
1200 350 350 2+2 767
1250 375 375 2+2 799
1500 3+3 959
250 250
2000 4+4 1278
900 200 200 2+2 786
1000 250 250 2+2 873
1100 300 300 2+2 960
MV1450 500 500 454 445 228 41 M48
1200 350 350 2+2 1048
1500 3+3 1310
250 250
2000 4+4 1746
1000 250 250 2+2 1114
1100 300 300 2+2 1226
MV1600 1200 350 500 350 500 507 480 261 50 M56 2+2 1337
1500 3+3 1671
250 250
2000 4+4 2228
[ Units: mm, kg ]

F
G J D E E D

Internal
steel plate H

T
M B C C B
F L

Standard manufacturing and performance tolerances apply (see pages 1236 to 1239)

M1100-S02-V1.1-EN. Trelleborg AB, 2007

26

MV ELEMENT
Rated Performance Data (RPD)*
F
L
Compound A Compound B R
L
E R E R
600 12.6 91.4 8.8 64
900 18.9 137 13.2 96 d
MV300
1200 25.2 183 17.7 128
1500 31.5 229 22.1 160 H
750 26.9 146 18.8 102
1000 37.4 203 26.2 142
1500 56.1 305 39.3 213
MV400
2000 74.8 406 52.3 284
2500 93.5 508 65.4 356
3000 112 609 78.5 427
750 41.2 179 28.9 125
1000 58.4 254 40.9 178
MV500
1500 87.6 381 61.3 267
2000 117 508 81.8 356 *Rated Performance Data (RPD)
750 49.9 197 34.9 138 Method: Decreasing Velocity (DV)
MV550 1000 70.7 279 49.5 196 Temperature: 23C
1500 106 419 74.2 293
Initial speed: 150mm/s
750 59.4 215 41.6 151
MV600 1000 84.1 305 58.9 213 Compression angle: 0
1500 126 457 88.3 320 Refer to p27.
750 90.4 262 63.2 183
MV750 1000 131 381 92 267
1500 197 571 138 400
800 111 302 77.8 212
1000 150 406 105 284
MV800
1500 224 609 157 427
2000 299 813 209 569
800 175 380 122 266
850 189 412 133 288
900 204 444 143 311
950 219 476 153 333
1000 234 508 164 356
MV1000 1050 248 540 174 378
1100 263 572 184 400
1150 278 604 195 423
1200 293 636 205 445
1500 350 762 245 533
2000 467 1016 327 711
800 269 468 188 327
850 293 510 205 357
900 317 551 222 386
950 341 593 239 415
1000 365 635 256 444
1050 389 677 272 474
MV1250
1100 413 718 289 503
1150 437 760 306 532
1200 461 802 323 561
1250 485 844 340 591
1500 548 952 383 667
2000 730 1270 511 889
900 426 638 298 447
1000 491 736 344 516
1100 557 835 390 584
MV1450
1200 622 933 436 653
1500 737 1105 516 773
2000 982 1473 688 1031
1000 598 813 419 569
1100 690 937 483 656
MV1600 1200 781 1061 547 743
1500 897 1219 628 853
2000 1196 1625 837 1138

All performance values are for a single element. [ Units: kNm, kN ]

Standard manufacturing and performance tolerances apply (see pages 1236 to 1239)

M1100-S02-V1.1-EN. Trelleborg AB, 2007

 27

MV ELEMENT

120

100

80
Reaction (%)

60 120

100

40 80

60

Energy (%)
20 40

20

0 0
0 5 10 15 20 25 30 35 40 45 50 55 60
Deflection (%) 57.5

example
Intermediate deections

Di (%) 0 5 10 15 20 28 35 40 45 50 57.5 62.5

Ri
Ei (%) 0 2 7 14 24 41 56 66 76 85 100 113

Ri (%) 0 31 58 78 92 100 96 90 85 84 100 130 Ei

Nominal rated deflection may vary at RPD. Refer to p1235. Di

Decreasing Velocity (DV) test method

The Trelleborg high-speed test press was
developed to simulate real berthing conditions
for MV and MI elements. Depending on element
size, initial speeds exceeding 300mm/s are
achievable.
The test press can accommodate single
elements from MV500 to MV1600 as well as
the MI2000 in lengths up to 1500mm.
Please refer to Trelleborg Marine Systems for
all special test requirements.

Standard manufacturing and performance tolerances apply (see pages 1236 to 1239)

M1100-S02-V1.1-EN. Trelleborg AB, 2007

28

MV SYSTEMS
H H
Element spacing Weight support

MV-elements can
r = rated deflection
support a lot of weight.
0.35H r=0.575H The table is a guide
to the permitted
weight of the front
panel in tonnes per
metre of element
0.24H pair before additional
support chains may be
required.
0.78H
WH WV

1.2H Panel weight* (kg)

MV Single or multiple Single or multiple
horizontal vertical
Compound A WH 1.0 H L WV 1.78 H L
0.32H
Compound B WH 0.7 H L WV 1.25 H L

* per pair of elements.

50 0.72H
Shear stiffness

Some temporary shear may

DL
be caused by friction as the
MV-elements are compressed.
FL
Maximum shear usually occurs at
approximately 28% deflection.
0.12H
DL 0.39 H FT R
DT 0.82 H
H
Where,
H = fender height
= friction coefficient
DT
MV-elements can be mounted
horizontally or vertically. There
must be enough space around and
between MV-element fenders and
the steel panel to allow them to Tension
deflect without interference.
Distances given in the diagram are If the likely tensile load exceeds the
for guidance. If in doubt, contact your rated reaction then tension chains F
local office. may be required. Please refer to your
local office.

Standard manufacturing and performance tolerances apply (see pages 1236 to 1239)

M1100-S02-V1.1-EN. Trelleborg AB, 2007

 29

MV SYSTEMS

Proven
in practice

Standard manufacturing and performance tolerances apply (see pages 1236 to 1239)

M1100-S02-V1.1-EN. Trelleborg AB, 2007

210

V-FENDERS
V-fenders fulfil the need for a simple,
and maintenance-free fender system
with high performance and a robust
design at low costs. All V-fenders use
one or several pairs of MV-elements
and a front shield. The shield is a
structural component of the fender,
directly bolted to the MV-element
and easily able to withstand constant
use in busy harbours.
The UHMW-PE face is also very
gentle on ships. It will conform to
the contours of the hull, will not
mark paint (unlike rubber) and does
not spark. UHMW-PE has very low
friction which reduces stresses in
the V-fenders and fixings.

Applications
B General cargo quays
B Berthing dolphins
B Pontoon fendering
B Passenger ferry berths
B Offshore platforms
B Long fender walls

Standard manufacturing and performance tolerances apply (see pages 1236 to 1239)

M1100-S02-V1.1-EN. Trelleborg AB, 2007

 211

V-FENDERS
Dimensions Performance (per metre)

Compound A Compound B
H T(min) So MW SW A B C Fixings
E R E R
MV300P* 70 370 270 410 360 454 172 M20 42.0 305 29.5 213
MV400P 80 480 360 500 480 606 232 M24 74.8 406 52.4 284
MV500P 90 590 460 660 600 774 316 M30 117 508 81.8 356
MV550P 90 640 500 750 660 834 320 M30 141 558 99.0 392
MV600P 90 690 530 800 720 894 322 M30 168 610 118 426
MV750P 100 850 680 1010 900 1136 440 M36 262 762 184 534
MV800P 100 900 730 1170 960 1218 480 M36 300 812 210 568
MV1000P 120 1120 900 1330 1200 1524 580 M42 468 1016 328 712
MV1250P 120 1370 1140 1660 1500 1904 724 M48 730 1270 512 888

Please ask for other dimensions [ Units: mm ] [ Units: kNm, kN ]

* MV300 not available in 1000mm length (refer to p24).
Performance is for a pair of elements, 1000mm long.

L
L

SW
MW C
C
A
B
A
B

H
H
SO
SO T T

Always specify P type elements for V-fenders

(ie. MV500P). These have special internal plates
designed to ex with the UHMW-PE shield. The
ange marked Panel Side should be connected
to the shield.

All V-fender performances are based on decreasing

velocity (DV) method compression testing of full
size elements. Performances are valid for 150mm/
s initial impact velocity, 23C ambient temperature
and 0 compression angle.
Site operating conditions or project
specifications may differ from the above. Please
ask your local Trelleborg Marine Systems office for
further details, or visit our web site.

Standard manufacturing and performance tolerances apply (see pages 1236 to 1239)

M1100-S02-V1.1-EN. Trelleborg AB, 2007

212

MI-2000
ELEMENTS
MI-2000 fender systems suit very
large vessels and high energy
applications. They share the
modular design concept with MV
elements but with a modified
fixing arrangement to allow greater
deflections and efficiency.
The rubber unit is available
in several standard lengths and
rubber grades which, combined with
the modularity of the MI system,
provides designers with greater
choice and versatility.

Features
B Modular design system
B Choice of lengths and rubber grades
B High performance and efficiency
B Long, life, low maintenance

Applications
Ideal for larger vessels including:
B Tankers and LNG ships
B Bulk carriers
B Post-Panamax containers
B Mega cruise ships

Standard manufacturing and performance tolerances apply (see pages 1236 to 1239)

M1100-S02-V1.1-EN. Trelleborg AB, 2007

 213

MI-2000 ELEMENTS
MI-2000 Dimensions
B
A B C Anchor Holes Weight
A
1000 1270 1130 M42 6+6 1840 2000
1050 1320 1180 M42 6+6 1941
1100 1370 1230 M42 6+6 2042 1318
1150 1420 1280 M42 6+6 2144
1200 1470 1330 M42 6+6 2245 733 52
1250 1520 1380 M42 6+6 2346
210
1300 1570 1430 M42 6+6 2447 H 210
1350 1620 1480 M42 6+6 2549
C
1400 1670 1530 M42 6+6 2650 585

[ Units: mm, kg ]

MI-2000S Dimensions
B
A B C Anchor Holes Weight* A
1000 1270 1130 M42 6+6 2191 2000
1050 1320 1180 M42 6+6 2286
1100 1370 1230 M42 6+6 2383 1318
1150 1420 1280 M42 6+6 2480 52
1200 1470 1330 M42 6+6 2573 75
733
1250 1520 1380 M42 6+6 2670
210
1300 1570 1430 M42 6+6 2765 210
1350 1620 1480 M42 6+6 2860
585 C
1400 1670 1530 M42 6+6 2957 H
[ Units: mm, kg ]

210
75 thick 620
210

* MI-2000S weight includes fabricated

spacers for both flanges (supplied with
fender elements on request).

Standard manufacturing and performance tolerances apply (see pages 1236 to 1239)

M1100-S02-V1.1-EN. Trelleborg AB, 2007

214

MI-2000
MI-2000 Performance
140
A Compound A Compound B
ER 925 565
1000
120 RR 925 565
ER 971 593
1050
RR 971 593
100
ER 1017 621
1100
RR 1017 621
Reaction (%)

80 ER 1063 650
1150
140 RR 1063 650
60 120 ER 1110 678
1200
RR 1110 678
100
ER 1156 706
40 80 1250
RR 1156 706

Energy (%)
60 ER 1202 734
1300
20 40 RR 1202 734
20 ER 1248 763
1350
RR 1248 763
0 0
0 10 20 30 40 50 60 ER 1295 791
1400
Deflection (%) 62 RR 1295 791
All values are for [ Units: kN, kNm ]
a single element.

example
Intermediate deections

Di (%) 0 5 10 15 20 25 30 35 40 45 50 55 60 62 65
Ri
Ei (%) 0 2 6 14 23 32 42 52 61 71 79 88 96 100 103

Ri (%) 0 34 63 84 95 99 100 98 95 91 86 82 90 100 127 Ei

Nominal rated deflection may vary at RPD. Refer to p1235. Di

All MI-2000 performance values are based on

decreasing velocity (DV) method compression
testing of full size elements on a dedicated high
speed test press. Performances are valid for
150mm/s initial impact velocity, 23C ambient
temperature and 0 compression angle.
Site operating conditions or project
specifications may differ from the above. Please
ask your local Trelleborg Marine Systems office
for further details, or visit our web site.

Standard manufacturing and performance tolerances apply (see pages 1236 to 1239)

M1100-S02-V1.1-EN. Trelleborg AB, 2007

 215

MI-2000S
MI-2000S Performance
140
A Compound A Compound B
ER 989 604
1000
120 RR 925 565
ER 1039 635
1050
RR 971 593
100
ER 1088 665
1100
RR 1017 621
Reaction (%)

80 ER 1138 695
1150
140 RR 1063 650
60 120 ER 1187 725
1200
RR 1110 678
100
ER 1237 756
40 80 1250
RR 1156 706

Energy (%)
60 ER 1286 786
1300
20 40 RR 1202 734
20 ER 1336 816
1350
RR 1248 763
0 0
0 10 20 30 40 50 60 ER 1385 846
1400
Deflection (%) 66 RR 1295 791

All values are for [ Units: kN, kNm ]

a single element.

example
Intermediate deections

Di (%) 0 5 10 15 20 25 30 35 40 45 50 55 60 66 67.5
Ri
Ei (%) 0 2 6 13 21 30 40 49 58 67 75 82 90 100 103

Ri (%) 0 35 63 83 95 99 100 98 94 90 85 81 81 100 110 Ei

Nominal rated deflection may vary at RPD. Refer to p1235. Di

All MI-2000S performance values are based on

decreasing velocity (DV) method compression
testing of full size elements on a dedicated high
speed test press. Performances are valid for
150mm/s initial impact velocity, 23C ambient
temperature and 0 compression angle.
Site operating conditions or project
specifications may differ from the above. Please
ask your local Trelleborg Marine Systems office
for further details, or visit our web site.

Standard manufacturing and performance tolerances apply (see pages 1236 to 1239)

M1100-S02-V1.1-EN. Trelleborg AB, 2007

Trelleborg Marine Systems is part of Trelleborgs Engineered collective experience and knowledge of its sales and
Systems Business Area and specialises in the safe berthing engineering staff. Our customers benefit from great choice and
and mooring of vessels within ports and harbours, on offshore helpful support at every stage from initial concept and detailed
structures and in waterways around the world. design right through to supply, commissioning and after-sales
We bring together the industrys best known and respected service all provided by our network of regional offices and
brands for fendering and mooring systems with the unrivalled local agents.

Americas Japan
Tel: +1 540 667 5191 Tel: +81 3 3512 1981
[email protected]
[email protected]
Presented by
Asia
Tel: +65 6268 8005 Middle East
[email protected] Tel: +971 4 886 1825
[email protected]
Australia
Tel: +61 2 9285 0200
[email protected] Scandinavia
Tel: +46 410 51 667
Benelux [email protected]
Tel: +31 180 434040
[email protected] Spain
Tel: +34 945 437 906
Central Asia [email protected] Trelleborg AB has made every effort to ensure that the technical specifications
Tel: +91 79 4003 8700
and product descriptions in this catalogue are correct. The responsibility
[email protected]
or liability for errors and omissions cannot be accepted for any reason
UK whatsoever. Customers are advised to request a detailed specification and
France Tel: +44 1666 827660 certified drawing prior to construction and manufacture. In the interests of
Tel: +33 1 41 39 22 20 [email protected] improving the quality and performance of our products and systems, we
[email protected] reserve the right to make specification changes without prior notice. All
dimensions, material properties and performance values quoted are subject
Harbour Marine to normal production and testing tolerances. This catalogue supersedes the
Germany information provided in all previous editions. If in doubt, please check with
Tel: +49 40 600 4650 Tel: +61 3 9575 9999
Trelleborg Marine Systems.
[email protected] [email protected]

www.trelleborg.com/marine
[email protected]