User Guide

RE6500
Linksys AC1200 Max Wi-Fi Range Extender

Introduction Overview
This User Guide can help you connect the extender to your network and solve
common setup issues. You can find more help from our award-winning, 24/7
customer support at Linksys.com/support. Front

Contents
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
How to install the range extender . . . . . . . . . . . . . . . . . 2
How to access the browser-based utility . . . . . . . . . . . 3
Using Wi-Fi Protected Setup . . . . . . . . . . . . . . . . . . . . . . 4
How to use Site Survey . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Power Light
Cross-Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Wireless Music Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 The light on the front of the range extender gives you information about power
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 and Wi-Fi Protected Setup. Use Wi-Fi Protected Setup to automatically and securely
connect client devices such as wireless printers that support Wi-Fi Protected
Setup. Note: Your antennas might look different from those pictured here.

Power Light Status/ description

Blinking white When the extender is powered on,
is resetting to factory defaults, or
upgrading its firmware
Solid white When the extender is ready to use

Blinking amber for two minutes When the extender cannot establish a
connection or encounters a problem
Fix: Unplug the power from the
extender, plug it back in, wait two
seconds, and then reconnect it to
your network

1
Linksys AC1200 Max Wi-Fi Range Extender

How to install the range extender 12VDC

1.5A

Before setup, unplug or disconnect any range extenders on the network.

1. Connect the antennas and power cable as pictured. Antennas should be
upright for best results. Note: Your antennas might look different from those
pictured here.

Wi-Fi Protected
Audio Jack Ethernet Setup button Power

Back 12VDC
1.5A

Power Switch European versions only.

2. Plug in the range extender midway between your router and the area
Wi-Fi Protected Setup Button Use Wi-Fi Protected Setup to automatically and
without Wi-Fi. Be sure you have at least 50% of your routers Wi-Fi signal at
securely add wireless devices to your network. Refer to Using Wi-Fi Protected
that point on the device you will use for setup.
Setup on page 7.
Range Extender
Ethernet (blue) Connect wired devices to your wireless network with
Ethernet (network) cables. The green light turns on when an Ethernet device
is connected and active on this port. The light blinks when the extender is
sending or receiving data over the Ethernet port.
Audio Port Connect the extender to your speaker.

Bottom 3. Wait for a solid light on the cover of the range extender. It could take up to
two minutes. On a computer, phone or tablet, connect to the Wi-Fi network
Linksys Extender Setup.
Windows 7 and Windows 8 will ask you, Do you want to set up your
network? Click the link, Connect to network without setting it up.

Reset button

4. If setup doesnt start automatically, open a browser to http://192.168.1.1.

Reset Press and hold this button for about five seconds to reset the extender to TIP
its factory defaults. You can also restore the defaults from the Administration > You can also connect the range extender by using Wi-Fi Protected Setup. For
Factory Defaults screen in the extenders browser- based utility. more information, see Using Wi-Fi Protected Setup on page 7.

2
Linksys AC1200 Max Wi-Fi Range Extender

How to access the browser-based utility Mac OS X

After setting up the extender use the extenders browser-based utility to 1. Open Safari. Click the book icon. Click Bonjour on the left panel. Look for
change any settings. the RE6500 icon on the bottom right panel.
2. Double-click the RE6500 icon.
Windows XP: 3. Leave the User name blank, and enter the default password admin.
TIP 4. Click OK.
To follow these instructions, UPnP needs to be enabled in
Windows XP. To enable UPnP:
Changes to settings will not be effective until you click Save Settings at the
1. Click Start, Control Panel, Add or Remove Program, then click Add/ bottom of the screen. You also can click Cancel Changes to clear any changes.
Remove Windows Components. Click Help on the right side of the screen for additional information on the
screens options.
2. Select Network Services, then click Details.
3. Select UPnP User Interface, then click OK

1. Open Windows Explorer. Click My Network Places on the left panel.

2. Look for the RE6500 icon on the right panel. (You might be required to
change the firewall settings to allow the display of networked computers.
Refer to your operating systems help for instructions.)
3. Double-click the RE6500 icon. A web browser will open and prompt you
to enter your User name and Password.
4. Leave the User name field blank, and enter the default password admin.
5. Click OK.

Windows 8, Windows 7, or Vista:

1. Open Windows Explorer (File Explorer in Windows 8). Click Network. Look
for the RE6500 icon on the right panel. (You might be required to change
the firewall settings to allow the display of networked computers. Refer to
your operating systems help for instructions.)
2. Right-click the RE6500 icon. Click Properties. Click on the address link in
Device webpage. A web browser will open and prompt you to enter a
User name and Password.
3. Leave the User name blank, and enter the default password admin.
4. Click OK.
3
Linksys AC1200 Max Wi-Fi Range Extender

Using Wi-Fi Protected Setup

Wi-Fi Protected Setup makes it easy to connect your extender to your network,
and connect other devices to your network through the extender.

Wi-Fi Protected Setup light activity

WPS Light Status/ description
Blinking white When WPS connection is in process
Solid white When WPS connection is successful
Blinking amber for two minutes When WPS cannot establish connection
or encounters a problem
Fix: wait a few seconds after LED stops
blinking and try again

Connecting the extender to an existing access point

If your access point or router supports it, you can use Wi-Fi Protected Setup
to connect the range extender to the access point or router. Choose from the
setup methods below to connect the extender. Connecting with the Wi-Fi Protected Setup Button
Use this method if your router or access point has a Wi-Fi Protected Setup button.
NOTE
If you have an access point or a router that does not support Wi-Fi Protected
Setup, note the wireless settings, and then manually configure the extender.

1. Press the Wi-Fi Protected Setup button on the extender.

2. Click the Wi-Fi Protected Setup button on the routers Wi-Fi Protected
Setup screen (if available), OR press and hold the Wi-Fi Protected Setup
button on the router for one second. When the connection is complete,
the Wi-Fi Protected Setup light on the extender will be solid.
3. If you used the extenders Wi-Fi Protected Setup screen, click OK in that
screen within two minutes.
4
Linksys AC1200 Max Wi-Fi Range Extender

NOTE NOTE
If you have a dual-band router and wish to connect to both bands, you will Repeat the instructions for each client device that supports Wi-Fi Protected
have to perform the WPS setup twice. The first connection will be on the 2.4 Setup.
GHz band.

Connecting with the Wi-Fi Protected Setup Button

Connecting with the range extenders PIN
Use this method if your client device has a Wi-Fi Protected Setup button.
The Wi-Fi Protected Setup PIN (Personal Identification Number) can be found
on the product label on the bottom of the extender. You can use this method
only if your routers administration utility has a Wi-Fi Protected Setup menu.

1. Enter the extenders PIN into the appropriate field on the routers Wi- Fi
Protected Setup screen. Click Register. When the connection is complete, 1. Press the Wi-Fi Protected Setup button on the client device.
the Wi-Fi Protected Setup light on the extender will be solid. 2. Click the Wi-Fi Protected Setup button on the extenders Wi-Fi Protected
2. Click OK. Setup screen, OR press and hold the Wi-Fi Protected Setup button on
the top panel of the extender for one second. When the connection is
Connecting devices to your network through the complete, the Wi-Fi Protected Setup light on the extender will be solid.

extender 3. If using the extenders Wi-Fi Protected Setup screen, be sure to click OK
within two minutes or you will have to start over.
Choose from the methods below to connect devices that support Wi-Fi
Protected Setup to your network.
Connecting with the client devices PIN
Use this method if your client device has a Wi-Fi Protected Setup PIN (Personal
Identification Number).

1. Enter the PIN from the client device in the field on the extenders Wi-Fi
Protected Setup screen.
2. Click Register on the extenders Wi-Fi Protected Setup screen. When the
connection is complete, the Wi-Fi Protected Setup light on the extender
will be solid.
3. Click OK on the extenders Wi-Fi Protected Setup screen within two minutes
or you will have to start over.

5
Linksys AC1200 Max Wi-Fi Range Extender

Connecting with the extenders PIN

Use this method if your client device asks for the extenders PIN.
1. On the client device, enter the PIN listed on the extenders Wi-Fi Protected
Setup screen. (It is also listed on the product label on the bottom of the
extender.) When the connection is complete, the Wi-Fi Protected Setup
light on the extender will be solid.
2. Click OK on the extenders Wi-Fi Protected Setup screen within two
minutes.

How to use Site Survey

Site Survey gives a snapshot of all neighboring access points and wireless
routers within range of the extender.
To open the Site Survey page:
1. Log in to the browser-based utility (see How to access the browser- based
utility on page 5). To connect your extender with an access point or router in Site Survey, you
2. Click the Wireless tab. Click the Site Survey page. will need to know the password or passphrase of the network on that device.

3. SelectTo connect to a wireless network, click the button next to the 1. Select the network name (SSID) that you want to repeat with your extender
wireless network name (SSID) in the Select column, and click Connect. by clicking the corresponding button in the Select column.

4. SSIDDisplays the name of neighboring wireless networks. 2. Click Connect. When prompted, enter the password or passphrase used to
secure your wireless network. The type of security information required in
5. GHzDisplays the radio band (in GHz) of the neighboring wireless this screen must match your access point or routers wireless security settings.
networks
6. Signal StrengthDisplays the relative position of the neighboring
access points by indicating the power of the wireless signal received: 1
bar= 20%,2 bars=40%, 3 bars=60%, 4 bars=80%, 5 bars=100%. If no bar is
displayed, the extender is located too far away from the upstream access
point. Try to keep the signal strength between 60% and 100% for optimum
performance.
7. SecurityDisplays the mode of security in use by the neighboring APs. If
a network supports Wi-Fi Protected Setup, the Wi-Fi Protected Setup icon
is also displayed.

3. Click Save Settings. Your extender wireless parameters should be

configured. The wireless interface will restart, and the extender will
connect to the access point or router you have chosen.

6
Linksys AC1200 Max Wi-Fi Range Extender

Cross-Band Troubleshooting
Cross-Band is the simultaneous use of both bands for high-speed data transfer
and uninterrupted streaming and gaming.
NOTE
Your RE6500 works on 2.4GHz and 5GHz networks.
Wireless Music Playback

You cannot get your extender connected

Check the position of your router and extender
For first-time setup, you may need to place the extender closer to the
router. After youve set up your extender, you can unplug it and move it to
The extender allows you to stream music on your network and play on on the final location.
speakers through the audio port. This list of supported media players is subject To reduce signal obstructions, try alternate locations for the router and
to change with the release of new software or mobile apps. extender.
Windows users can stream music with Windows Media Player12. Avoid placing the router and extender near metal objects, masonry walls,
Mac users can stream music with proprietary software or the SofaPlay app. and reflective surfaces such as glass or mirrors.
Android users can stream music with MediaHouse, UPnPlay, Skifta, ArkMC, Avoid placing the router and extender near other electronics that may
BubbleUPnP, Pixel Media, and 2Player 2.0. cause signal interference.
iOS devices including iPhone, iPad or iPod can stream music with If youre using Wi-Fi Protected Setup to connect
proprietary software or other apps such as ArkMC, Smartstor Fusion, Wait until the Wi-Fi Protected Setup indicator stops blinking before trying
Mconnect, and DK UPnP/DLNA. to make the connection again.
The extender supports MP3, FLAC, WAV, WMA and AAC file formats, as long
as those formats are supported by the device and app doing the streaming.
The 3.5mm stereo port supports earphones and powered speakers.
You cannot access your range extender
To access your range extender, you must be connected to your own network. If
you currently have wireless Internet access, the problem may be that you have
accidentally connected to a different wireless network.
For Mac instructions, see To fix the problem on Mac computers: on page 8.
To fix the problem on Windows computers:

1. On your Windows desktop, right-click the wireless icon in the system tray.
The icon might look different depending on which version of Windows you
are running.
7
Linksys AC1200 Max Wi-Fi Range Extender

2. Click View Available Wireless Networks. In the example below, the computer was connected to another wireless network
named JimsRouter. The name of the Linksys E-Series network, BronzeEagle in
this example, is selected.

3. Select your network name. Click Connect. In the example below, the
computer was connected to another wireless network named JimsRouter.
The name of the correct network, BronzeEagle in this example, is selected.

2. Select the wireless network name of the router you want to connect to.
3. Type your wireless network password (Security Key) into the Password
field. Click OK.

4. If you are prompted to enter a network key, type your password (Security
Key) into the Network key and Confirm network key fields. Click Connect.
You should now be able to access the range extenders browser-based utility.
To fix the problem on Mac computers: You have intermittent connection problems
1. In the menu bar across the top of the screen, click the Wi-Fi icon. Linksys Plug in the range extender midway between your router and the area without
Connect has automatically assigned your network a name. Wi-Fi. Be sure you have at least 50% of your routers Wi-Fi signal at that point on
the device you used for setup.

8
Linksys AC1200 Max Wi-Fi Range Extender

Specifications

RE6500
Model Name Linksys RE6500
Model Description Dual-band Wireless-AC Range Extender
Model Number RE6500
Standards IEEE 802.11ac, 802.11a, 802.11n, 802.11g, 802.11b, 802.3u
Ports Gigabit Ethernet, Audio, power
Buttons Reset, Wi-Fi Protected Setup,
Power (European model only)
LEDs Power/Wi-Fi Protected Setup,
Ethernet (link, activity)
Cabling Type CAT 5e
Antennas 2 external
Detachable (y/n) Yes
Wireless Security Wi-Fi Protected Access 2 (WPA2),
Wi-Fi Protected Access (WPA), WEP
Security Key Bits Up to 128-bit encryption

Environmental
Dimensions 6.06 x 4.29 x 1.18 (154 x 109 x 30 mm)
Weight 5.57 oz (158 g)
Power 12VDC/1.0A
Certification FCC, ICES-003, RSS210, CE,
Wi-Fi (IEEE 802.11a/b/g/n/ac), WPA2, WMM,
Wi-Fi Protected Setup
Operating Temperature 32 to 104F (0 to 40C) Storage Temperature
-4 to 140F (-20 to 60C) Operating Humidity
10 to 80% noncondensing Storage Humidity
5 to 90% noncondensing

Specifications are subject to change without notice.

9
Visit linksys.com/support for award-winning 24/7
technical support

BELKIN, LINKSYS and many product names and logos are trademarks of the Belkin
group of companies. Third-party trademarks mentioned are the property of their
respective owners. Licenses and notices for third party software used in this product
may be viewed here: http://support.linksys.com/en-us/license. Please contact
http://support.linksys.com/en-us/gplcodecenter for questions or GPL source code
requests. 2014 Belkin Interntional, Inc. and/or its affiliates. All rights reserved.

LNKPG-00125 Rev. A01