SP 916 Ne

Note: Two kinds of fast access methods are provided on the The default access method is ADSL dial-up
The default access method is ADSL dial-up and the access account
router's web-based utility: ADSL dial-up and DHCP. and access password are the same as the ADSL dial-up account
and password, which you can inquire your broadband ISP. For
other access methods, please refer to WAN settings in chapter
2. If you select ADSL dial-up, you only need to enter the access
4.The wireless password can only consist of 8 characters, the
2. account and access password as well as the wireless password,
default is 12345678 and you can modify it when necessary.
2. and then click “Ok” to complete the settings.
Micronet
*********
3. If you select DHCP, you only need to enter the wireless

2. password and click “Ok” to complete the settings.
5 6
Search the AP router through Wireless network Communicate via
1. On the PC site, disable the LAN adapter and enable the

1. wireless adapter.
2. Use the adapter's utility to browse the wireless network

1. in neighborhood.
Quick Installation Guide
3. Find the AP router's name; click the item to open the
1. configuration page then key in the SSID that was set in the AP. 300Mbps/150Mbps Wireless
1. Save the setting then the PC can join the network of this AP.
LAN Broadband Router
4. Now, the PC can access Internet through this AP router.
Model No.: SP916NE/SP916NL
5.For further settings of this AP router, please refer the manual
1. on the CD.
SP916NL
SP916NE
WEEE Directive & Product Disposal

At the end its serviceable life ,this product should not be treated
as household or general waste. It should be handed over to the
applicable collection point for the recycling of electrical and
P/N 2300-0679 electronic equipment, or returned to the supplier for disposal.
w w w . m i c r o n e t . c o m . t w
7
Downloaded from www.Manualslib.com manuals search engine
Introduction Hardware Installation
Micronet SP916NE/SP916NL, 300Mbps/150Mbps Wireless
Broadband Router, delivers next generation wireless solution of
high speed and cost-efficient network. It is compliant with IEEE
802.11n and backward compatible with IEEE 802.11b/g. Best
selection for small office and home application where all computers Attach the power adapter to the 'Power' socket of the router
and network devices can share Internet access through a single and wall socket.
xDSL/cable modem. In addition, the scope of the network can be
Connect the xDSL / cable modem to the WAN port of router
easily expanded by connecting the router to a hub or switch.
by Ethernet cable.
Connect all computers and network devices to the LAN port

Package Contents (1~4) of the router.
Prior to the installation of the device, please verify the following Configuration
items are in the package:
Follow the steps below to configure and set up WLAN Broadband
WLAN Broadband Router Router. A computer with wired Ethernet connection to the
Quick Installation Guide wireless router is required for first time configuration.
User Manual & Utility CD IP Address Configuration

Power Adapter PC/Notebook must belong in the
RJ-45 1m cable same IP range and subnet. Follow
the steps below to configure IP
settings for LAN PC.
1.In the control panel, double click

1.on Network Connections. Double
1.click on the local area connection
1.(e.g. LAN). The following screen
1.will appear. Highlight 'Internet
1.Protocol (TCP/IP)' and click on
1.'Properties'.
1 2
2.Select 'Obtain an IP address automatically' and 'Obtain Default Values

2.DNS server address automatically', then click <OK>.
IP Address 192.168.1.1
Subnet Mask 255.255.255.0
Password '1234'
Web-based User Interface
SP916NE/SP916NL is embedded with http sever and provides a

series of web pages, which display the configuration and status of
the system. After configuration of IP, the management interface can
be access by entering the IP address of the AP into the browser.
3.In DOS command, type 'ipconfig' to view information on LAN 1. Login page will appear to prompt users to enter the username
2.connection. Ensure the IP address and subnet mask are on the 1. and password.
2.same subnet as the router.
3 4
Downloaded from www.Manualslib.com manuals search engine

SP 916 Ne

Uploaded by

Copyright:

Available Formats

SP 916 Ne

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SP 916 Ne

Uploaded by

Copyright:

Available Formats

Note: Two kinds of fast access methods are provided on the The default access method is ADSL dial-up

3. If you select DHCP, you only need to enter the wireless

Search the AP router through Wireless network Communicate via

1. On the PC site, disable the LAN adapter and enable the

2. Use the adapter's utility to browse the wireless network

WEEE Directive & Product Disposal

Connect all computers and network devices to the LAN port

User Manual & Utility CD IP Address Configuration

1.In the control panel, double click

2.Select 'Obtain an IP address automatically' and 'Obtain Default Values

Web-based User Interface

SP916NE/SP916NL is embedded with http sever and provides a

You might also like