GREAT PLANES

RealFlight Generation 4 and the

InterLink Elite Controller

Great Planes Model Manufacturing Company

P.O. BOX 788, Urbana, IL 61801

Table of Contents
Introduction

RealFlight G4 Feature Highlights

How to read this manual

2
6

Before You Begin

System Requirements
Video and Sound Cards
Getting the Most out of RealFlight

7
8
9

Getting Started

Installing RealFlight G4
Using Your Own R/C Radio
Exploring RealFlight G4
Where to Go From Here

11
11
15
17
31

The InterLink Elite Controller 33

Start Flying!

34

The Simulation Menu

37

Select Airport
Edit Current Airport
Utilizing the Editor
Create New Airport
Capture Screenshot
Mute/Unmute Audio
Environment
Flight Failures
Import
Export
Manage User Files
Settings
Exit
Airport MRU

38
40
52
58
60
61
62
66
69
72
74
76
107
108

The Aircraft Menu

Aircraft Selection
Edit Current Aircraft
Select Color Scheme
Save Color Scheme As
Remember Aircraft Position
Clear Aircraft Position
Reset Position
Kill Engine
Aircraft MRU

109
111
113
125
126
129
130
131
132
133

Controller Menu

135

Select Controller
Controller Calibration

136
137

Channel Mapping
139
Joystick Mode vs. Transmitter Mode
142
InterLink Elite Controller (Joystick Mode)
142
InterLink Elite Controller (Transmitter
Mode)
143
Transmitter Mode: Joystick Emulation
Interface
145
Transmitter Mode: Pass Through Interface
146
InterLink Elite Controller Tips
147

Events Menu
Autorotation/Deadstick
Autorotation/Deadstick Instructions
Freestyle
Freestyle Instructions
Limbo
Limbo Instructions
Pylon Racing
Pylon Racing Instructions
Spot Landing
Spot Landing Instructions
Options
End Current Event
Forfeit Turn

Multiplayer Menu
Chatting
Host
Join
Disconnect
Boot Player
Publish Hosting Information
Enter MultiMode

149
151
154
156
159
160
164
165
168
170
173
175
176
176

179
181
181
184
187
188
188
189

Recordings Menu

193

Training Menu

201

Start Recording
Stop Recording
Open Recording
Record Microphone Input
Recordings MRU
Takeoff Trainer
Landing Trainer
Heli Hover Trainer
Airplane Hover Trainer

194
195
195
199
200
202
207
211
218

Heli Orientation Trainer

Virtual Flight Instruction

224
226

View Menu

231

Window Menu

243

Show
Camera Type
Camera Position
Look At
Quick Look
Zoom Type
Zoom In
Zoom Out
Zoom Reset
Head Tracking

232
233
234
235
236
237
239
239
240
241

Show Title Bar

Gadgets
Arrange
Close All
Viewport List

244
245
256
257
258

Help Menu

261

Contents
Keyboard Commands
About
License
Websites

262
263
264
265
266

Basics of Flying

269

Airplane Basics
Helicopter Basics
Helicopter Flight

RealFlight G4 Launcher
Run RealFlight
Additional Options

269
272
278

279
280
280

If You Experience Difficulties289

How to Get Help and Information
Before You Do Anything Else
If You Need Additional Assistance
Examples of Common Problems and
Solutions

289
290
292
293

Glossary

295

Index

313

License

319

Credits

323

Chapter

Introduction
Welcome to the RealFlight Generation 4 R/C Flight Simulator
(also known as RealFlight G4, or simply G4).

ealFlight G4 is, without question, the most advanced R/C aircraft simulation
available. RealFlight G4 is so technologically advanced and so realistic, youll
find it hard to believe that its only a simulation. The culmination of many
years of development and design, G4 offers advancements that will serve to
fine-tune the flying skills of even the most seasoned R/C veteran. If youre an entrylevel R/C-er, RealFlight G4 is the ideal way to learn to fly, practice maneuvers, feel the
effects of design modifications, or just have an incredible amount of fun.
RealFlight G4 includes over 80 models that look and fly like the real thing, plus a
multitude of flying siteseach with their own unique feel and distinctive
characteristics. In addition, G4 offers its users the most powerful and flexible aircraft
and flying site editors ever unveiled to the modeling community, allowing modelers to
experiment with a virtually unlimited number of parameters. G4 enables you to
change the look and feel of a flying site with nothing more than a few keystrokes, the
click of the mouse and a little imagination. The integrated AccuModel aircraft editor
makes modifying aircraft just as easy.
RealFlight G4 also offers a wide array of tools to help you understand how to use the
program and how to improve your R/C piloting skills. This extensive manual file
explains every feature and option as well as how to use them. Our Virtual Flight
Instruction feature, Heli Hover Trainer, Airplane Hover Trainer, Takeoff and Landing
Trainer and Heli Orientation Trainer provide on-the-fly learning opportunities, and our
trained and dedicated Product Support staff is ready to provide help when you need it.
No other R/C simulator goes further to enrich your R/C experience.
The following section briefly outlines some of the exciting features in RealFlight G4.
We strongly suggest that you peruse this manual in its entirety before running the
software. Subsequent chapters will describe all RealFlight features in complete detail.

Finally, wed like to express our gratitude to you for purchasing RealFlight G4. We
think you will be enormously pleased with G4. Have fun flying!

RealFlight G4 Feature Highlights

This section briefly outlines some of the new features included in RealFlight G4 with
the USB InterLink Elite Controller. RealFlight G4 and the multi-patented InterLink
Elite Controller incorporate a significant number of enhancements and improvements
over previous RealFlight systems.
USB InterLink Elite Controller

The InterLink Elite Controller by Futaba is a revolutionary device that offers you:

A high quality USB compatible plug and play controller for RealFlight G4.

A built-in interface for (optionally) using your own R/C transmitter to control
RealFlight G4.

QuickSelect Buttonstake control of RealFlights menus and options from

the InterLink Elite without touching the keyboard or mouse.

The InterLink Elite Controller is fully hot swappableyou can connect and
disconnect the InterLink or your own transmitter without rebooting your
computer (or even shutting down RealFlight).

High-speed response to control inputs.

Digitally precise inputs with digital trims for unmatched control precision.

MultiMode split screen capability allows you to use the InterLink Elite as a
controller and an interface simultaneously.

A keyboard-free push button reset of the simulation.

Hand-launch gliders and other aircraft that do not incorporate landing gear.

Menu-Driven Interface

RealFlight G4 utilizes a drop-down menu-driven interface system. Created for ease of

use and maximum flexibility, the menu system provides an interface familiar to even a
casual computer user.
Additional Features

RealPhysics 3D - One of the most ambitious models of flight in the world,

RealPhysics 3D is untouched in its ability to re-create the lifelike characteristics
of model flying. RealFlight G4s physics engine has been tried and approved
by world-class competition pilots like Todd Bennett, John Glezellis, Pete
Niotis, Frank Noll, and Jason Shulman. Furthermore, aircraft in G4 behave

with real-world predictability because they are carefully modeled using

advanced methods and extensive real-world data. If it happens at the field or
in the air, its re-created with exacting detail in G4!

Float Fly- RealFlight G4 offers a number of flying sites with water along with
a variety of float fly aircraft. Practice your takeoffs and landings on water and
admire the view at the same time.

InterLink Elite QuickSelect-With RealFlight G4s InterLink Elite, youre

able to make quick changes such as selecting a different aircraft or airport
without touching the keyboard or mouse.

Variable Pitch Prop-Take 3D flight to 4D with the variable pitch prop.

Select the popular FlatOuts Extra 300S with V-Pitch and try amazing
maneuvers you didnt think were possible with an airplanelike flying
backwards.

Hovering Training Aids- Learn to torque roll or hover a heli with

RealFlights Heli and Airplane Hover Trainer. For more excitement, try the
Heli Orientation Trainer. Both are great training aids for anyone new to radio
control.

Takeoff and Landing Training Aids-The RealFlight G4 simulator is a great

way for new pilots to learn the art of R/C flying. And the best places to start
are training aids designed to teach you the basics of Takeoffs and Landings.

Night Flying- Just because the sun is down doesnt mean that you cant fly.
The same is true with RealFlight night flying. Pick a nighttime airport and
watch as your aircraft lights up the sky.

PhotoFields- G4 also includes ultra-realistic PhotoField airports. Using

incredible high resolution digital images, RealFlight PhotoField airports are as
real as it gets. And the Import feature allows you to use your own panoramic
photos to create new flying sites.

Full Coverage collision detection- Instead of using sensors at only a few

points, Full Coverage blankets the entire aircraft with points ensuring that
every part of an aircraft will not only register a strike but will react
authentically. Contact can result in damage ranging from minor handling
problems to spectacular crashes complete with realistic sound effects.

TruFlo Wind Dynamics- RealFlight G4 introduces modelers to R/Cs

most realistic wind model. The five components of TruFlo Wind Dynamics
work together to create the single most accurate wind field in any simulation.
Wind impacts every facet of your flight, just as it would at the local field.

AccuModel Aircraft Editor- G4s new aircraft editor is the most powerful
and most flexible editor ever introduced in an R/C simulator. AccuModel
allows you to change virtually every aspect of your model with easeit places

over 1,500 airfoils at your disposal, a multitude of propellers, and much, much
more! AccuModel brings up a wire-frame model for easy reference and
highlights the editing area. Make a change and its immediately reflected onscreen, ready for review and revision.

Sierra Nevadas Flying Sites and over 5,000 square miles to exploreRealFlights TrueLife Terrain goes beyond the limitations of traditional
simulator flight. Created and mapped from satellite imagery, G4s landscape
looks as right and richly varied as the view from your front door. Digital
elevation data brings it all into accurate perspective.

A living, breathing environment- Everything in G4s 3D world is as realistic

as possible, complete with depth and details that transcend the traditional
billboard look of other simulators. Youll see leaves and branches that dance
in a passing breeze and clouds that roll by with the prevailing winds.

FlexiField flying site editor- Takes you beyond 2D scenes into a 3D

environment rich in new objects and editing options. Customize an existing
field with new foliage, different objects or both -- or create a new field with
nothing more than a mouse, imagination and a few simple keystrokes.

InterLink Elite Controller- G4s InterLink Elite controller functions as a

controller, as an interface, or both. Its push-button is capable of resetting the
aircraft or hand-launching a sailplane.

Fly Split Screen- G4s MultiMode option allows two modelers to fly
simultaneously on one PC. Its perfect for practicing formation flight, a game
of tag or personalized flight instruction.

Uses VirtualRevolution sound technology-- Doppler-correct stereo sounds

heighten the realistic effect with true sound recordings of 2-stroke, 4-stroke,
turbine, electric, ducted fan and gasoline engines. As the aircraft crosses the
field, the engine sound follows, just like its R/C counterpart.

RotoSonics technology-- recreating distinctive engine/blade sounds with

startling accuracy. Sounds so lifelike, youll swear you are at the field!

VFI (Virtual Flight Instruction) -- VFI gives you personal flight lessons
from R/Cs leading experts. Using VFI, you can select a maneuver (loop, roll,
etc.) from an extensive list of options. VFI then demonstrates the maneuver
on-screen, performed by an expert. While you watch, the voice of the
pilot/instructor will explain how to perform the maneuver.

AFR (Advanced Flight Recorder) -- This feature allows the pilot to not only
view prerecorded maneuvers, but also to record maneuvers of his/her own as
well. G4 even allows you to record your own audio for personalized flight
instruction. Much like a VCR, this feature also allows you to pause, speed up,
slow down, and loop the performance. You can also play multiple recordings

at the same time. The pilot has the option to activate the digitized transmitter
display so that he/she can view the radio input while flying.

NavGuides- Using the NavGuides, you can display a variety of heads-up

on-screen informational displays. Options range from altitude and airspeed to
aircraft heading and engine RPM. This feature improves your ability to see
what is going on in your virtual world.

Viewport- You can open up a picture-in-picture display and treat it as an

independent window on the world. You can individually adjust each the
viewports vantage point, zoom level, and direction of view.

Multiplayer-You can fly with up to seven additional RealFlight G4 owners in

competitions, or just for the thrill of flying with one another. This feature can
also be used to learn new maneuvers from pilots across the street or around
the world.

Events- Compete solo, or fly with up to seven additional RealFlight G4

owners in a variety of Events such as: Limbo, Spot Landing, Free Style, Auto
rotation and Pylon Racing.

Launcher- RealFlight G4s Launcher allows for easy one-click access to

program upgrades, online registration, and technical support.

Animated control surfaces and retractsControl surfaces, retracts,

propellers, and rotor blades move for added realism.

Aircraft exhaust/smoke-You can control the color, density, hang time, and
other parameters related to airplane and helicopter smoke and exhaust.

Streamers- Add streamers to any aircraft, to any location, in any color. Watch
as they corkscrew behind the airplane during a roll, or react to the wind and
the propwash.

Flight Failures- RealFlight can simulate many common flight failures (radio
interference, stuck servos, engine failures, etc.). Use this feature to prepare for
emergencies at the field.

Fully editable aircraft paint/decal schemes- Create customize trim

schemes for your aircraft. (To design your own paint scheme, you must use a
third-party program that edits TGA files.)

Extensive Help materials- RealFlight G4 features extensive online tool tips

and diagrams, a detailed manual and technical support to enhance your
enjoyment of the program.

How to read this manual

RealFlight G4 is a menu driven simulator which allows you to make quick changes
without having to reload the simulator each time. This manual will break out each
main menu to its own chapter. This allows you to quickly find information on features
and functions by the related menus.
Along with this manual, a large RealFlight community is available online to help and
discuss with each RealFlight fan. This online support, in the form of a forum, can be
found at:
http://www.knifeedge.com/forums/

Chapter

Before You Begin

To get the most out of RealFlight G4, it helps to understand how to get the most
out of your computer first.

ealFlight Generation 4 is designed to work on a large variety of computer

hardware. Similar to a car, if you want to go faster, you need a bigger engine.
The same holds true with RealFlight. Youll be able to enjoy the simulator on
most modern computers, but having the most up to date hardware for your
computer will greatly increase your enjoyment.

System Requirements
You will find the suggested system requirements for the RealFlight G4 R/C Flight
Simulator listed below. The minimum system requirements below are the bare
minimum PC configuration for installing RealFlight G4. Meeting the minimum
requirements will allow you to enjoy G4. However, in order to take complete
advantage of the many features and functions offered by G4, you should have a
computer at, or near, the specifications as specified in the optimum system
requirements.
Minimum Recommended System-

- Some graphical features may be disabled

- Aerodynamic Calculations will still be high-quality
Windows* 98SE, ME, 2000, XP or Vista
Intel Pentium 1.0GHz or equivalent
512 MB RAM

3 GB Hard Drive Space

3D Accelerated Video with:
- 32 MB Dedicated Video Memory
- Full DirectX 9 compliant (Pixel Shader 1.4 support)

Optimal System

- For best graphical performance

Dual Core 2.4GHz CPU
2 GB RAM
3D Accelerated Video with:
- 256 MB dedicated video memory
- Pixel Shader 2.0 support
Multiplayer Requirements

56.6 Kbps (or faster) modem or LAN connection

Video and Sound Cards

In order to achieve optimum performance and the best flying experience in RealFlight,
there are two important components of your computer that deserve special attention:
the video and sound cards.
RealFlight G4 has undergone countless hours of compatibility testing and evaluation.
As such, this software will adequately function with a variety of video cardsranging
from yesterdays favorites to tomorrows hits.
While RealFlight works well on a wide variety of hardware configurations, it offers
many features and functions that are designed to take particular advantage of the latest
video technology. If you have an older computer, or a newer computer with a lowerend video card, you may want to consider purchasing a new video card to take
advantage of these features and functions. This moderately priced upgrade can vastly

enhance your enjoyment of RealFlight. Aside from increasing your satisfaction with
G4, a new video card will also work with many other games or simulators, improving
their performance as well.
For a list of the video cards that have been tested by our staff, please visit:
http://www.gpsoftware.com/
While not as important as the video card, upgrading your sound card may also improve
your satisfaction with RealFlight. This is especially true if your computer uses an onboard sound card (a sound card affixed to the motherboard).

Getting the Most out of RealFlight

We think youll agree that RealFlight offers the finest set of instructions and practice
tools of any R/C simulator suited for both beginners and experienced pilots. Great
Planes and Knife Edge Software are committed to the continual improvement of our
products. When using the software, you should keep two things in mind.
First, similar to other pursuits, what you get out of RealFlight depends upon what you
put in. Mastering radio control requires a great deal of patience and practice. If you
crash an aircraft in the simulation, take it very seriously. Crashing an actual R/C
aircraft can cost you a lot of time and money. Try to examine what you did incorrectly,
using the experience to avoid making the same mistake again.
Secondly, while the simulator is quite realistic and will assist you in learning many of the
skills necessary to become a proficient pilot, there is no substitute for actual flying time
at the field. A simulation can be a wonderful practice tool. However, no simulator, no
matter how realistic, can completely replace a qualified, experienced, human flight
instructor. If you are new to R/C, you should never attempt to fly a real aircraft
without the supervision of a qualified instructor, no matter how accomplished you are
on the simulator.

Chapter

Getting Started
A brief overview and assistance to help start you on your R/C adventure.

his chapter covers the installation procedure for RealFlight

G4, describes the basics of running the program, and introduces you to some
of RealFlights frequently used features.

The first section, Installing RealFlight G4, offers a step-by-step approach to the
installation procedure for both the program software and the controller.
The second section, Exploring RealFlight G4, offers a brief tour of the RealFlight G4
program. You'll learn how to perform some basic functions, such as selecting the
aircraft you wish to fly, performing simple edits to the flying field, manipulating
viewports, and using RealFlights Virtual Flight Instruction feature.
This chapter only touches briefly on some of RealFlight G4s features. We strongly
suggest that you also read the subsequent chapters, which describe the various features
in comprehensive detail.

Installing RealFlight G4
The RealFlight G4 InterLink Elite controller has several different modes of operation.
By itself, it serves as a realistic stand alone controller or joystick. Alternatively, it has a
built-in interface that lets you use your own R/C transmitter to control RealFlight G4.
The final mode of operation combines the InterLink Elites ability to serve as a
controller and an interface simultaneously.

11

The USB InterLink Elite Controller-

To install RealFlight G4 using the InterLink Elite controller, follow the instructions in
this chapter.
Regardless of whether you plan to use the InterLink Elite controller by itself, or with
your own R/C radio to control RealFlight, follow the instructions on Program
Installation in the next section.
Program Installation-

RealFlight Generation 4 features a simple, one-step installation process. There are,

however, further steps that must be followed prior to running the program for the first
time. This section will explain how to install the RealFlight G4 software and hardware.
Upon completion of this section, you should be able to fly the aircraft on your PC.
The InterLink Elites built-in transmitter interface also allows you to use your own R/C
transmitter to control RealFlight G4 should you opt to do so. To activate the interface
adapter, you will first need to follow the instructions in the section below. This section,
will explain the methodology of using the transmitter interface option in the InterLink
Elite controller.
Update Drivers-

Before you begin installation, we strongly suggest that you update the drivers
for both the sound and video cards on your PC. A driver is a software
program that your computer uses to control hardware devices. Each card has
its own respective driver. Most problems with installing and using RealFlight,
as well as many other programs that use DirectX, arise from using outdated
video and/or sound card drivers.
If you are not sure how to update your drivers, you can find instructions in
article
Q01-1038,
Locating
and
installing
drivers,
at

12

http://www.gpsoftware.com/kb/q01-1038.htm. This support article will take

you through the process step-by-step, and has links to driver download sites
for most manufacturers.
Installing the Software-

After you have completed installation of the new video and sound card drivers,
you are now ready to install RealFlight G4.
1. Before installing the software, make sure to close any applications that
you are running. This includes virus scanning software and other
similar applications.
2. Insert Disc 1 (One) into the appropriate CD-ROM drive.
3. If Auto-Play is active, setup will begin automatically when the CDROM drive is closed. Simply click the Install button when prompted.
If Auto-Play is not active, click Start on the task bar. Next, click Run.
In the dialog box that appears, type d:\setup (assuming that d is
your CD-ROM drive) and click OK.
Follow the on-screen instructions to complete the setup procedure. When
prompted, remove Disc 1 (One) and insert Disc 2 (Two). Following the onscreen prompt, remove Disc 2 (Two) and insert Disc 3 (Three). Following
the on-screen prompt once again, remove Disc 3 (Three) and insert Disc 4
(Four). Upon completion of the installation, click OK.
Installing or Updating DirectX-

1. RealFlight will ask if you wish to install DirectX 9 on your PC. It is

important that your PC utilizes DirectX 9.0c or later. Click OK to
proceed to the DirectX License Agreement.
2. Click "I accept the license agreement" to install DirectX 9.0c.
Alternatively, if you do not wish to update DirectX at this time, click
Cancel.
3. If you have opted to accept the license agreement, click Next to
proceed with the installation. DirectX will install the necessary files to
update your PC.
4. When prompted, click Finish. Your PC will power down and then
restart once again.

Connect the InterLink Elite Controller-

The InterLink Elite controller uses the USB (Universal Serial Bus) port, so
there is little to do in the way of setup.

13

1. With the software installation procedure complete, firmly plug the

InterLink Elite controller into one of the unused USB ports on the
PC. Because the controller is hot swappable, you do not have to shut
the PC down to plug the controller in.

2. Shortly after plugging in the InterLink Elite controller, a dialog box

should appear on the screen indicating that Windows has located a
new device and will then automatically install the necessary drivers.
Note: It is possible that Windows will need to install the appropriate files for
the InterLink Elite controller to function properly. Please have your Windows
CD-ROM available in case it is required.
Starting RealFlight Generation 4-

1. Double-click the RealFlight G4 Launcher located on your desktop.

2. Type in your name, software serial number and the InterLink Elite
controller serial number in the appropriate location. Please be sure
to enter the numbers exactly as they appear. Failure to enter the serial
numbers correctly will not allow you to proceed to the next step. If
the serial numbers are entered properly, the OK button will become
active.

14

3. Click OK. The RealFlight G4 Launcher will appear. Click Run

RealFlight. RealFlight G4 will start with a default aircraft and default
flying site.
Note: The procedure above will allow you to pilot the RealFlight aircraft using
the InterLink Elite controller. The InterLink Elite controller may also be used
as an interface unit, allowing you to pilot the aircraft with your actual R/C
transmitter. For information on how to do so, please refer to the section
entitled Using Your Own R/C Radio which follows.

Using Your Own R/C Radio

Follow these instructions if you intend to use your own R/C transmitter to control
RealFlight G4. If you do not want to use your own transmitter, skip this section.

15

Connecting Your Transmitter-

You can use your R/C transmitter to control RealFlight G4 by connecting it to the
InterLink Elite controller, buddy box style (see diagrams). RealFlight G4 includes
several adapter cables used to make the connection to many popular R/C transmitters.

Locate the cable input port on the rear of the InterLink Elite Controller. Plug one end
of the included connector cable into this port. Next, plug the other end of the adapter
cable into the buddy box port (a.k.a. trainer jack) of your transmitter. The procedure
for doing so depends on your transmitter:

If your transmitters buddy box port directly accepts the 1/8 stereo plug, insert
this end directly into the radio. This works for most JR radios.

If your transmitters buddy box port requires the micro (square) connector, use the
squared adapter cord included with the simulator.

16

Some radios (e.g., Airtronics, Hitec and older Futaba transmitters) require the
purchase of an optional adapter cable. This adapter cable is available wherever you
purchased your copy of RealFlight G4.

Setup-

After you have connected your transmitter to the InterLink Elite controller, you will
need to perform a brief setup procedure before utilizing it with the simulation.
1. First, make sure that the transmitter is in FM or PPM mode rather than PCM
mode. Refer to the manual for your transmitter if you are unsure how to do
this.
2. If the transmitter did not power up when the interface cord was plugged into
it, turn the power switch on at this time.
3. Next, click the Controller menu and then highlight the Select Controller
menu item. After a brief delay an option for the InterLink Elite Transmitter x
channel should appear. Choose the InterLink Elite Transmitter X Channel
option.

Exploring RealFlight G4
Now that you have completed the installation of RealFlight G4, its time to begin
exploring the program. The following sections will take you on a quick tour of
RealFlight G4s most popular features, such as selecting an aircraft, choosing alternate
flying locations, customizing the flying sites, and using the training aids instruction.
Along the way, we will show you where to go for help and how to obtain additional
information.
Even if you are familiar with previous versions of the RealFlight software, you should
read this section thoroughly. The features described here are either new or have been
completely revised for G4.
Start the Program-

1. Close all open applications. This includes virus scanning software and other
similar programs.
2. Double-click the RealFlight G4 Launcher located on your desktop.
3. To start the simulation, click the Run RealFlight button.
The program will start using the pre-set defaultsincluding pilot perspective, flying
location, and aircraft.

17

The Main RealFlight Display-

RealFlight G4 is a menu-driven program. As seen in the picture below, a menu bar

appears across the top of the RealFlight screen. The menus contain additional menu
items and pull-down lists for the related options of the respective menu. These menus
allow access to the command and control functions for the RealFlight G4 simulation.
Navigating the Menus-

To access the various menu items, simply highlight and click the mouse on the
menu that you would like to view. For example, clicking on the Aircraft menu
activates the sub-menu items for that menu.

The top-level menus found in G4 are as follows:

Simulation

Aircraft

Controller

Events

Multiplayer

18

Recordings

Training

View

Window

Help

This manual includes a separate chapter for each menu title. Later chapters
describe in detail all of the menu items, sub-menus and options.
Please note that it is also possible to access many of the features and functions
of RealFlight Generation 4 using hot keys. Pressing the H key on the
keyboard activates the Keyboard Commands dialog, which summarizes the
available hot keys.
Aircraft Selection-

When you start G4 for the first time, you will be piloting an Extra 300L. This is the
default aircraft for RealFlight G4.
To select a different aircraft, click the Aircraft menu title in the main menu bar. Next,
click the Select Aircraft menu item found in the drop-down menu. This activates
the Select Aircraft dialog (as shown below), which displays a list of available aircraft.

19

Each aircraft available in G4 is listed along the left-hand side. The icon next to each
name differs depending on whether the model is an airplane or a helicopter. To select
an aircraft from the list, click on the desired aircraft. The selected model will now
appear in the ReadySelect preview box. Additionally, an aircraft description and
information data will appear in the aircraft information pane, which appears just below
the ReadySelect preview window.
When you are satisfied with your selection, click OK to return to the simulator using
the new aircraft selection.
Complete information pertaining to the Select Aircraft menu item is available in
chapter 6 of this manual, The Aircraft Menu.
Alternatively, you may use the InterLink Elite controller to change aircraft selections.
Simply press the Menu/Select button located on the front of the InterLink Elite
controller. This will bring forth the QuickSelect tabs on the left side of the computer
screen and the aircraft selection tab, represented as an airplane icon, should be the
highlighted tab. Press the Menu/Select button once again to bring up the Aircraft
Selection dialog box. Move the Data Lever, found on the lower right side of the
InterLink Elite controller, up or down to view the available aircraft. The [+] (plus)
indicates that there is another expansion level (selection) available to you, press the
Menu/Select button to access the items located within this folder.

20

To select an aircraft, simply highlight the name and press the Menu/Select button.
You will return to the simulation using the newly selected aircraft.
If you wish to exit the Aircraft Selection screen without making any changes, simply
press the Reset button on the InterLink Elite.
Aircraft Most Recently Used List (MRU)-

If you have selected alternative aircraft previously, you will note that these aircraft
appear on a list in the Aircraft menu, as shown below. This list is at the very bottom of
the menu. This list is commonly referred to as a Most Recently Used, or MRU list. It
is limited to the eight most recently used aircraft. If you wish to fly one of the aircraft
from this list, simply click on the name of the aircraft in the MRU list.

Airport Selection-

Changing flying sites uses a process similar to the process used to select an aircraft. To
select a new flying location, click the Simulation menu located in the header. Next,
click the Select Airport menu item found in the drop-down menu. This opens the
Select Airport dialog, which lists the available flying locations. Select either the
Archipelago, PhotoFields, or Sierra Nevada location.

21

Each scene is preceded by a [+] (plus) and an icon. The [+] (plus) indicates that
another expansion level (selection) is available to you. To access the complete list of
airports for a particular scene, either click the [+] (plus) or double-click on the desired
airport. For example, clicking the [+] (plus) on the PhotoFields folder reveals all of the
PhotoFields flying sites available to you.
To select an airport from the list, click on the desired airport. The selected airport will
now appear in the preview box. Additionally, an airport description will appear in the
information pane, which appears just below the preview window.
When you are satisfied with your selection, click OK to return to the simulator using
the new airport selection. Navigating the Airport Selection menu using the
QuickSelect feature is almost identical to the process mentioned above for selecting an
alternative aircraft. Only this time, you will select the airport selection menu, which is
represented by a runway icon. With the QuickSelect tabs visible on the computer
screen, move the Data Lever down one time. This should highlight the runway icon.
Press the Menu/Select button to bring forth the available flying sites. Using the same
method, as described previously for aircraft, select the new airport and press the
Menu/Select button to return to the simulation using this new flying site.
Airport Most Recently Used List (MRU)-

If you have previously selected an alternative flying location, it will appear on a list in
the Simulation menu. This list is at the very bottom of the menu and is commonly
referred to as a Most Recently Used, or MRU list. It is limited to the eight most
recently selected locations. If you wish to fly at one of these locations simply click on
the respective location in the MRU list to load it into the simulation.

22

QuickSelect Tabs-

RealFlight G4 offers a revolutionary methodology in which to access many features

and functions quickly and easily without ever touching the keyboard or mouse. There
are seven main areas of access available through the QuickSelect tabs. They are as
follows: Airplane Selection, Flying Site Selection, NavGuides, On-Screen Radio,
Binocular view, Viewports and Variometer.
To access any of the QuickSelect tabs, press the Menu/Select button on the
InterLink Elite controller. This will bring forth the available options on the left side of
the computer screen. Move the Data Lever up or down to cycle through the
QuickSelect tabs. The highlighted tab is the item that is active. To access the active tab,
press the Menu/Select button.

23

For additional information on how to use the QuickSelect tabs, please refer to the
information contained in the section entitled QuickSelect- on page 35.
Some Common Tasks-

The easiest method of resetting your aircraft to its original takeoff position is to
press the reset button located on the front of the InterLink Elite controller.
Alternatively, you can reset the aircraft by pressing the space bar on the keyboard,
or by selecting the Reset Position menu item, which is located in the Aircraft
menu.

If your aircraft is equipped with smoke, the two-position switch located on the
right side of your InterLink Elite controller will generally be utilized to activate this
feature.

To magnify the view or zoom in on an aircraft, press the [+] (plus) key on the
number pad of the keyboard. Alternatively, you may use menu commands to
zoom in. To do so, click on the View menu and then click on the Zoom In menu
item. Each time the [+] (plus) key or the Zoom In menu item are pressed or
selected, the view will increase incrementally.

To reduce the magnification, or zoom out of the current view press the []
(minus) key on the number pad of the keyboard. Alternatively, you may use

24

menu commands to zoom out. To do so, click on the View menu and then click
on the Zoom Out menu item. Every time you press [-] (minus) key or select and
press the Zoom Out menu item, the view will decrease incrementally.

To reset the view to the default magnification, press the Backspace on the
keyboard.

Creating a Viewport-

RealFlight allows you to create an additional picture-in-picture viewport. Once you

create a new viewport, you may resize or reposition it by dragging with the mouse.
You can also fully adjust all of the viewports properties independently of the main
window. The viewports may be utilized for a variety of applications, such as changing
the viewing perspective of your simulation.
To create a new viewport, click the Window menu title followed by the Create New
View menu item. Alternatively, you may also press the 4 key on the keyboard to
create an additional viewport.

To change the vantage point within the viewport, press the C key on the keyboard.
The C toggles through the various camera modes; the first of which is the cockpit or
pilots perspective. The second is chase view, and the last mode is the fixed viewpoint,
or what you would see if you were standing at the side of the runway. Please note:

25

depending upon the flying site selected, some of these viewing options may not be
applicable.
The Window chapter of this manual contains a thorough explanation of the viewports
and the viewport options.
Using Gadgets-

The RealFlight G4 software includes several gadgets that may be displayed in the main
window when running the software. A gadget is an on-screen display that provides
helpful information or allows you to access to a variety of RealFlight features and
functions.
For example, the NavGuides gadget displays continuously updated information
relating to your aircrafts altitude, airspeed, directional heading, and other flight
parameters. To display the NavGuides gadget, click the Window menu title followed
by the Gadgets menu item. Next, select the NavGuides gadget located in the dropdown menu. You may also access the NavGuides gadget by pressing the numerical 1
key on your keyboard. Alternatively, you may activate the NavGuides gadget through
the QuickSelect tabs. To do so, press the Menu/Select button on the InterLink Elite
controller. Next, move the Data Lever downward twice. Finally, press the
Mode/Select button to activate the NavGuides.
When you select NavGuides, you should see the NavGuides gadget appear on your
screen:

As discussed previously, you can customize the gadgets for personal preference. For
complete information on how to do so, please refer to the chapter pertaining to the
Window menu options.
Virtual Flight Instruction-

RealFlight G4 includes a variety of basic, intermediate and advanced pre-recorded

maneuver lessons for helicopter and airplane pilots. A professional, award-winning
R/C pilot talks you through every facet of the maneuver. You can use the Virtual
Flight Instruction to learn new maneuvers as well as to perfect those maneuvers that
you already know.
To activate the pre-recorded maneuvers, click on the Training menu followed by the
Virtual Flight Instruction menu item. Alternatively, press the V key on your

26

computers keyboard. Either method brings forth two options: airplane and
helicopter, each preceded by a [+] (plus) symbol. Each option has a number of pilots
listed beneath. To select amongst the pilots, click the [+] (plus) which precedes their
name. Alternatively, you may double-click the pilots name.

To select a maneuver, double-click the name of the maneuver itself. Alternatively,

highlight the name of the maneuver by clicking on it, then select OK. After you have
selected a maneuver, click OK to proceed. RealFlight G4 will automatically load the
default airport and then start the VFI recording.
Once the VFI starts, you will see the instructors aircraft fly the maneuver and hear the
instructors voice explaining how its done. As depicted below, you can also watch the
instructors actual stick movements using the on-screen, digitized R/C radio.

27

You can even fly your own aircraft next to the instructors! This allows you to mimic
the inputs and aircraft reaction simultaneously. To simultaneously watch your aircraft
and the instructors, create an additional viewport focused on your aircraft. The main
window will show the instructors aircraft and the on-screen radio will show the
instructors stick movements. The newly created viewport will show your aircraft.

28

RealFlight Trainers-

RealFlight G4 includes several training aids to help learn the basics of taking off and
landing an airplane. Obviously, mastering these skills is essential to the success of your
entry into radio control flight.
The Takeoff training feature, as the name suggests, is designed to enable pilots of all
skill levels to perfect their takeoffs.
To select the Takeoff training feature, click on the Training menu title followed by the
Takeoff Trainer menu item. The Takeoff Trainer will start using the default
settings. If, however, you wish to alter any of the settings, click on the Trainer menu
title. For additional information pertaining to these settings, please refer to the section
entitled Takeoff Trainer on page 202 in this manual.

29

The Landing Trainer feature is designed to enhance a pilots landing skills. As with
full-scale aircraft, it is imperative that an R/C pilot be well-versed in the proper
technique of landing their aircraft in various conditions. Failure to land an aircraft
properly may result in a damaged aircraftor perhaps even destroy it entirely.
To select the Landing Trainer feature, click on the Training menu title followed by the
Landing Trainer menu item. The Landing Trainer will begin with the aircraft in a
pre-determined position using its default settings. If, however, you wish to alter any of
the settings, click on the Trainer menu title. For additional information pertaining to
these settings, please refer to the section entitled Landing Trainer located on page 207
in this manual.

30

Airport Editing-

RealFlight G4 offers the most powerful, flexible flying site editor ever produced on an
R/C simulation. G4s FlexiField editor allows you to completely customize virtually
every aspect of your flying sites.

You can add, remove, change the orientation of, or resize virtually every aspect of your
flying site. You can alter the position and orientation of the ground objects (such as
runways) that snap to the terrainyou can even have a runway running up a hill! Its
even possible to control lighting, terrain, clouds, fog/haze, and much more. FlexiField
provides you with almost unlimited freedom to create the flying environment you
want. Moreover, when youve created an airport, you can share it with other RealFlight
G4 users.
To learn more about the FlexiField flying site editor, please refer to the section titled
Edit Current Airport on page 40.

Where to Go From Here

The examples in this chapter only scratch the surface of RealFlight G4s unparalleled
capabilities. You can fly with others over the internet, fly with a friend using

31

MultiMode on the same PC, try your hand at a limbo event, customize your aircrafts
flight parameters, and much, much more! We encourage you to explore RealFlight G4
using some of the methods below.

Browse through the menus. Many of the menus are self-explanatory, providing
you with a more thorough look at the software. If youre adventuresome, dive
right in and start making modifications to an aircraft or a flying site! Its a great
way to learn more about what makes G4 tick!

If youd like to learn more about a particular menu or item, look it up in the table
of contents.

If you would like RealFlight G4 to perform a certain function but cannot locate the
appropriate command, check the index.

Use the Help facilities in RealFlights Help menu.

Talk to other RealFlight users at www.knifeedge.com.

32

Chapter

The InterLink Elite

Controller
The InterLink Elite is your all-access pass to the RealFlight world.

he R/C transmitter is a key component in all types of R/C flying. This unique
method of control is part of what separates R/C from every other type of
aviation. Consequently, a realistically simulated transmitter is an important key
to an authentic simulation of the R/C experience.

With this in mind, we at Great Planes are proud to offer our revolutionary USB
InterLink Elite (U.S. Patent #6,842,804 and #7,010,628) controller, made by Futaba.
The InterLink Elite controller was designed from the ground up to meet the needs of
the R/C purist. We believe that no other R/C simulator control method goes farther
to enrich your R/C simulator experience.

33

Features of the InterLink Elite Controller-

USB compatibility and convenience. The InterLink Elite offers the plug and
play convenience, hot pluggable installation and removal, as well as the highspeed digital performance made possible by Universal Serial Bus (USB)
technology.

High quality mockup transmitter. Use the InterLink Elite controller by itself as a
pseudo R/C transmitter, with the controls you expect in a standard 8-channel
radio. The mockup transmitter features two 2-position switches, one 3-position
switch, a rotary knob, knurled control sticks with adjustable length and a pushbutton reset.

Built-in Transmitter interface. If you so choose, you can use your own FM or FMcompatible R/C transmitter to control RealFlight, using the InterLink Elite
controllers built-in interface. You can even switch back and forth between the
pseudo controller and your own transmitter! Interface adapter cords are included
for most JR, Futaba and Hitec transmitters.

Simultaneous interface and controller. The InterLink Elite makes it possible for
two modelers to fly on the same PC, each using his/her own controller to pilot the
aircraft.

QuickSelect menu controls. With the InterLink Elite, youre able to make a variety
of common adjustments to the simulator (such as, selecting a different aircraft or
airport.) without having to touch the keyboard and mouse.

Easy setup and use. Unlike other computer joysticks, in most cases, you do not
even have to calibrate the InterLink Elite controller. Simply plug it in and go!

Simulate sophisticated computer radios. The InterLink Elite, used in conjunction

with the RealFlight software, allows you to simulate the programmability (mixing,
exponential, etc.) of sophisticated computer radios.

Start Flying!
When you start RealFlight for the first time, the software will automatically detect the
InterLink Elite controller. Simply add throttle and start flying right away.
RealFlight, by default, uses the InterLink Joystick setting. This setting affords G4 the
plug-and-play capability in the simulation. In this mode, the InterLink Joystick allows
the InterLink Elite to control all functions associated with the flight of your aircraft.
The InterLink Elite also allows you to use your own R/C transmitter to control the
RealFlight aircraft. This is referred to as the Transmitter Interface Mode.

34

QuickSelect-

The InterLink Elite also offers QuickSelect buttons located at the bottom of the
controller. These buttons allow you to make simple changes to the simulator without
having to put the controller down and reach for the keyboard and/or mouse. This
makes it convenient to change the current aircraft and airport, or display popular onscreen gadgets.
To access the QuickSelect tabs, press the Menu/Select button to display a number of
tabs on the left side of the simulator. Use the Up and Down direction on the Data
Lever, located on the lower right side of the controller, to scroll through these options.
Pressing the Menu/Select button again will select the highlighted tab. Pressing the
Cancel button on the InterLink Elite will exit out of the tabs and hide them.
The options available are:

Select Aircraft

Select Airport

NavGuides Gadget

Radio Gadget

Binocular View

Viewport

Variometer
When using the QuickSelect buttons in the Select Aircraft or Select Airport dialog
screen, press Menu/Select to select the current highlighted item. Pressing Cancel on
the InterLink Elite will move you up a level so you can quickly change folders. To exit
out of these dialog screens without making any changes, simply press the Reset
button.

35

Look for the icon to the left throughout this manual for suggestions
on when to use the QuickSelect buttons.

36

Chapter

The Simulation Menu

Allows access to a variety of simulation-related features, functions and options.

he Simulation menu brings forth a pull-down menu, giving you access to many
simulator related features, such as changing flying sites or importing and
exporting RealFlight files.

Clicking the Simulation menu will bring forth a screen that looks similar to the
following screen shot.

Menu items that are available are:

Select Airport...

Edit Airport Name

37

Create New Airport

Capture Screenshot

Mute Audio

Environment

Flight Failures

Import

Export

Manage User Files

Settings

Exit

Airport MRU

Select Airport
When you click on Select Airport the following dialog appears:

38

This dialog lets you choose the flying site that you wish to use for your flight. Each
location offers its own unique characteristics and challenges.
The list on the left of the dialog box displays all of the flying sites available to you. If
you have created any flying sites, those sites will also be visible here.
The flying sites are listed in files and folders in accordance with the software from
which they were loaded. If, for example, you have installed Expansion Pack 2, the sites
from this disk will be listed, alphabetically, beneath the Expansion Pack 2 folder. You
can change how the airports are organized by clicking on the Grouping drop-down
and select another grouping option. The options are:
Product, Scene: As explained above, airports are first grouped into folders by the
product in which they are contained. Within each group they are then grouped further
by scene.
Product: Airports are grouped by product alone.
Scene: Airports are grouped by scene alone.
None: Airports are not grouped into folders at all.
alphabetically.

Rather, they are listed

Click the [+] (plus) or the [-] (minus) symbol to reveal or hide the airports within
these folders. To select an airport, click on the name of the airport at which you wish
to fly.
The rotating image on the right side of the screen provides you with a preview of what
to expect at the desired location. The dialog box below the terrain map contains a
description and pertinent information regarding the highlighted airport.
Have some fun while youre in the Select Airport dialog. Using the mouse, click and
drag the preview screen to point the camera angle to your choosing. To resume
rotating automatically, right-click the preview screen.
When you are satisfied with your selection, click OK to return to your flight using the
new airport selection.
The Cancel button will return you to the simulation at the previously selected flying
site.
Change airports simply by using the InterLink Elite. Press the
Menu/Select button, then, using the Data Lever, move down one
tab and press the Menu/Select button again. This will bring up the
Select Airport dialog window. You can continue using the

39

QuickSelect buttons in this dialog to select a new airport, or press Reset to resume
flying without making any changes.

Movement Modes

If applicable to the respective airports, Generation 4s Movement Modes allow you to

explore the scenery without an aircraft. Movement is not possible at PhotoFields
airports.
To select a Movement Mode, press the Q key on your keyboard. You can press the
Q key repeatedly to cycle through the available modes: Walk, Fly or Hover.
Walk mode simulates the effect of you, the pilot, physically walking across the field,
complete with sound effects. The Fly mode allows you to move through the air and
position the camera anywhere that you desire.
Once you have entered the desired Movement Mode, use the W, S, A and D keys
on your keyboard to control the movements. If you wish to increase the speed of your
movement, press and hold the Shift key at the same time you are using the W, S, A
or D key.
The mouse wheel controls the angle or height at which you traverse the scenery. To
increase the altitude, roll the wheel away from you. This is known as the Hover Mode.
You may also control the zoom levels during your travels. Press the [+] (plus) key to
Zoom In and the [-] (minus) key to Zoom Out. The Backspace key resets the
zoom level to its default value.

Edit Current Airport

RealFlight G4 offers unparalleled freedom to edit flying sites. You can add and
remove objects, alter their location, rotate, and even resize items. It is also possible to
alter the atmospheric or lighting conditions at the various flying locations. The first
several times you access the airport editing function, the possibilities might seem
daunting. It will require some getting used to before you are comfortable with this
feature and its related functions. The best way to do so is to simply dive in and
experiment.
To modify the currently selected flying location, click the Simulation menu followed
by the Edit <Current Airport> menu item, where <Current Airport> is the name
of the airport you have loaded at the moment. This activates RealFlight G4s
FlexiField flying site editor, with the currently active airport loaded and ready to edit.

40

Airport Editor Menus-

Selecting the Edit Current Airport option activates the screen shown above. There are
five menus in the Airport Editor dialog:

File

Edit

View

Options

Window

File Menu-

This menu and its menu items are used to manipulate and control the various folders
and related items in the airport editor.

41

Open-

This menu item is used to open existing and edited airports. Selecting this
menu item opens the Select Airport dialog.
Save-

This option becomes active once you have renamed and saved the edited
airport. Prior to doing so this option remains inactive and grayed out.
Save As-

Upon completion of the airport editing, click this menu item to save the
modifications. You will be asked to create a name for this new airport. After
you have renamed the airport, click OK to accept the new name. Afterwards,
the airport will appear in the airport listings found in the Select Airport
which is located in the Simulation menu.
Save folder-

This option allows you to select an entire sub-folder in an airport and save it as
a new file. For example, it is possible to select the entire Objects sub-folder
in RealFlight Ranch and save it off to a disc.

42

To save the folder, right click on the existing folder and select Save Folder.
This brings forth a dialog that allows you to determine the new folders name
as well as the location where it will be saved.
Alternatively, with the respective folder highlighted click on the File menu and
select Save Folder menu item from the pull-down menu.
Load Folder-

This option allows you to load a folder from the saved folders. To do so, right
click on an existing folder. Next, select the folder from the list.
Alternatively, with the respective folder highlighted click on the File menu and
select Load Folder menu item from the pull-down menu.
Exit to Simulator-

Use this option to cease editing the airport and return to the simulation. If you
have not made any changes to the airport, you will return directly to the
simulation. If you have unsaved changes, a message box will ask for
confirmation before returning to the simulation.
Edit Menu-

This menu may be used for some simple editing functions on the selected airport.

43

Undo-

Select this to undo the last change you made in the airport editor.
Redo-

Choose Redo to repeat the last action you did in the airport editor.
Cut-

Select one or more objects at the airport and choose Cut to remove the
selected objects. The objects are stored temporarily in RealFlights memory
and can be pasted back into an airport.
Copy-

Like the Cut options, Copy will store the selected objects in RealFlights
memory allowing you to later paste it into an airport. Unlike Cut, the selected
object will remain at the current airport.
Paste-

If any objects have been cut or copied, choose Paste to add them to the
current airport.
Delete-

Delete will remove the selected objects from the airport. They cannot be
retrieved later. Therefore, you cannot paste the object(s) back in the scenery.
Select All-

This menu option will select all objects at the airport you are currently editing.
Deselect-

Choosing this menu option will deselect any airport objects that might be
selected at the moment. If no objects are selected, Deselect will remain grayed
out.
Previous Object-

If any airport object is currently selected, choosing Previous Object will select
the preceding object in the folder list.
Next Object-

If any airport object is currently selected, choosing Next Object will select the
next object in the folder list.

44

Select Parent-

All objects belong to a group or parent. To select the parent that the current
selected object belongs to, choose Select Parent.
Select Child-

If a group is currently selected, choose Select Child to select the first object
listed in that group.
Set As Default Pilot Spawn-

Choose a pilot spawn and click this menu option to set it to the default
spawning point. This point will be the default camera position each time you
load the current airport.
View menu-

This menu allows you to make alterations and modifications related to the perspective
of the simulation during the editing process. Modifications to the vantage point do not
have any effect on the simulation during its operation.

Mode-

The Mode menu is utilized to alter the camera perspective when viewing the
scene. There are three distinct view modes in G4: Pan Camera, Pivot Camera

45

and Normal Camera. These modes, as well as the methods to access them will
be discussed in depth in the sections that follow.
Pan Camera-

The Pan Camera option allows the camera to shift the vantage point
on the selected scenery.
There are several ways to access the Pan Camera mode. The first, and
probably the easiest, is to press the C key on your keyboard.
Alternatively, you may right click on the scene and select Pan Camera
from the available options. The final method that may be used is to
select Pan Camera through the View menu and Mode menu item.
To increase the pan view, rotate the mouse wheel towards the
computer screen. Alternatively, you may also press the [-] (minus)
key on the number pad of the keyboard. This causes the camera to
zoom out incrementally.
Conversely, to decrease the pan view, either rotate the mouse wheel
away from the computer screen or press the [+] (plus) key on the
keyboards number pad. This causes the camera to zoom in
incrementally.
You can exit this mode by using the menus or by hitting the Z key,
which returns you to the normal viewing mode.
Pivot Camera-

The Pivot Camera mode, as the name suggests, pivots or rotates the
camera in relationship to a particular object or location.
There are several ways to access the Pivot Camera mode. The first,
and probably the easiest, is to press the X key on your keyboard.
Alternatively, you may right click on the scene and select Pivot Camera
from the available options. The final method that may be used is to
select Pivot Camera View menu and Mode menu item.
To increase the pivot view, rotate the mouse wheel towards the
computer screen. Alternatively, you may also press the [-] (minus)
key on the number pad of the keyboard. Doing so will cause the
camera to zoom out incrementally.
Conversely, to decrease the pivot view, either rotate the mouse wheel
away from the computer screen or press the [+] (plus) key on the
keyboards number pad. Again, this will zoom the camera in
incrementally.

46

To exit the Pivot Camera feature, right click in the editing view once
again and then mouse click the desired option in the popup menu.
You can also exit this mode by hitting the Z key, which returns you
to the normal viewing mode.
Normal Camera-

This mode returns the camera to its normal, or default perspective.

There are several ways to access the Normal Camera mode. The
easiest is to simply press the Z key on the keyboard. Alternatively,
you may right click in the scene and select Normal Camera from the
options listed. Finally, you may select Normal Camera through the
View menu and Mode menu item.
Center View on Selection-

This option centers the vantage point on a particular object. This is useful for
repositioning, resizing, rotating, etc.
If you have not selected an object from the Folder Listing or highlighted an
object in the scene, this option will remain inactive or grayed out. If, however,
you have made a selection or highlighted an object, there are several ways to
select the Center View on Selection option.
Simply right click on the selected object or folder in the Folder Listing.
Alternatively, in the scene, right click on the highlighted object and select the
Center View on Selection from the options listed. The final option is to use
the View menu and select the Center View on Selection option.
To magnify the view or zoom in on the selected item, press the [+] (plus) key
on the keyboard. Each time you press the [+] (plus) key or select the Zoom
In menu item, the zoom level increases incrementally. Alternatively, you may
select the Zoom In option from the View menu.
To decrease the magnification, or zoom away from the selected item, press the
[-] (minus) key on the keyboard. Each time you press the [-] (minus) key or
select the Zoom Out menu item, the zoom level decreases incrementally.
Alternatively, you may select the Zoom Out option from the View menu.
Fit Selection in View-

This option is utilized to ensure that your selection fits in the view. If, for
example, your zoom magnification is at an extremely high level, the object may
not completely fit on the screen. This feature ensures that it will.

47

To access the Fit Selection In View, right click on the highlighted object in the
scene and select the Fit Selection In View from the options listed. The final
option is to use the View menu and select the Fit Selection In View option.
To magnify the view or zoom in on the selected item, press the [+] (plus) key
on the keyboard. Each time you press the [+] (plus) key or select the Zoom
In menu item, the zoom level increases incrementally. Alternatively, you may
select the Zoom In option from the View menu.
To decrease the magnification, or zoom away from the selected item, press the
[-] (minus) key on the keyboard. Each time you press the [-] (minus) key or
select the Zoom Out menu item, the zoom level decreases incrementally.
Alternatively, you may select the Zoom Out option from the View menu.
Zoom In-

Click this menu item to magnify or zoom in on the selected item.

Alternatively, you may magnify the view or zoom in on the selected item by
pressing the [+] (plus) key on the keyboard. Each time you press the [+]
(plus) key or select the Zoom In menu item, the zoom level increases
incrementally.
Zoom Out-

Click this item to reduce the magnification, or zoom out of the current view.
Alternatively, press the [] (minus) key on the keyboard. Alternatively, you
may zoom out via G4s menus. Each time the [-] (minus) key or the Zoom
Out menu item are pressed or selected, the view will decrease incrementally.
Zoom Reset-

This menu item resets the view to the default magnification. Alternatively, you
may also press the Backspace on the keyboard to reset the zoom to its default
value.
Options Menu-

The Options Menu allows you to adjust how many of the functions in the airport
editor will work.

48

Selectable Items-

The Selectable Items menu determines whether a particular type of object may
be clicked and selected on-screen.
To eliminate the possibility of selecting an item, simply mouse click on the
desired listing in the pull-down menu. This capability is useful if there are
many objects clustered in a small area and you want to select just one of them.
For example, suppose that an airport has a tight cluster of trees with a dirt pile
in the middle. If you want to select the dirt pile, it may be easier to turn off the
tree selection first. This will allow you to easily select the dirt pile without the
trees getting in the way.
Add Object Grouping-

The items available for addition in RealFlight G4 are all grouped or organized
accordingly. This menu item determines the methodology by which they are
grouped in the Object Palette window.
Product, Type, Name-

Selecting this option causes the objects in the Object Palette to be

displayed by the Product then by the Type and finally by the Name.
That is, objects are first listed within the product in which they appear
(e.g., G4, Expansion Packs, etc.). Within the product, the objects are

49

then classified by Type (e.g., Buildings, Trees, etc.). Once youve

selected the Product and Type of object that is desired, the objects are
then listed alphabetically by Name.
For information on adding objects and how to use the Object Palette,
please refer to the Object Palette section of this manual.
Type, Name-

This option causes the objects in the Object Palette to display by the
Type and the Name designations only. They are not sorted by the
Product in which they appear. Objects that appear in G4, Expansion
Packs, etc. will be included on one extensive listing.
This option is useful if you are unsure as to which product included a
particular object.
Name-

Selecting this option causes the objects to be listed in alphabetical

order by their name designations (e.g., Barn). This listing is extensive
as it includes all of the objects available to you.
This option is useful if you are unsure as to which product contained
the object or if you are unsure as to the type of object that you wish to
utilize. It also offers a rapid overview as to the number and breadth of
objects available to you.
Rotation Snap-

When rotating an object on the flying site, you have the ability to control the
amount of rotation with the Rotation Snap. There are four snap settings that
may be utilized in the editor to provide quick orientation settings for placing
objects.
None

The object rotates without any restrictions. This is useful for making
minor refinements to object placement.
45 Degrees

The object will rotate 45 degrees each time if this option is selected.
This is useful for making large changes to object position.
15 Degrees

The object will rotate 15 degrees each time if this option is selected.

50

5 Degrees

The object will rotate 5 degrees each time if this option is selected.
Display Metric Units-

Click this item with your mouse to switch the measurement indicators in the
Properties pane from SAE (feet, inches, pounds) to metric (meters,
centimeters, kilograms).
Window Menu-

This menu item activates or eliminates items from the display or window. For
example, if you were to click the Properties item in the pull-down menu this would
eliminate the Properties window from the screen.

Folder Listing-

This listing includes all of the folders available to you for use in the airport
editor. Selecting this item from the pull-down menu will remove the Folder
Listing dialog from the screen.

51

Object Palette-

The Object Palette includes the complete selection of objects available to you
for use in editing an airport. Selecting this item from the pull-down menu will
remove the Object Palette dialog from the screen.
Pilot Preview-

Selecting this item from the pull-down menu will eliminate the pilots
perspective from the screen.
Properties-

Selecting this item from the pull-down menu will remove the Properties dialog
from the screen.
Reset Window Position-

This menu item resets the positions of the airport editing windows back to
their default locations. Additionally, if you have removed any of the default
windows, they will return to the screen at this time.

Utilizing the Editor

Opening the airport editor reveals four distinct windows. For the purpose of clarity,
we will examine each window individually. It is, however, important to note that these
windows interact with one another.
Folder Listing Window-

The Folder Listing window consists of the folders and items (objects) that comprise
the currently selected airport.

52

To determine what items are contained within the Objects and Clouds folders, click on
the [+] (plus) or double-click on the name itself (e.g., Objects). Doing so brings up
the various sub-folders that are contained within the main item.
As denoted by the [+] (plus) symbols, these folders, in turn, also have another level.
Again, to open these respective levels, click on the [+] (plus) icon or double-click the
folder name.
Alternatively, clicking on an object in the scene will highlight the respective object. It
will also open the folder that contains the object. The converse is also true, clicking the
folder or object in the Folder Listing menu will highlight the respective item as well.
If you wish to move an object from one folder to another, mouse click and hold the
object to be moved. Next, drag the object to the desired location (folder) using the
mouse and release. The object will be listed at the bottom of the folder in which it has
been situated. Please note: this removes the object from the original folder.
You may use either of two methods to delete an object from the folder, and therefore
the scene as well.

53

First, you can highlight the object or sub-folder (e.g., Fences) in the Folder Listing and
press the Delete key on the keyboard.
Alternatively, with the object or sub-folder highlighted, right click and select the Delete
Object pull-down option.
Properties Window-

The Properties window indicates the detailed information for the item highlighted in
the Airport Editor window. Consequently, the contents of the Properties window vary
depending upon the selection in the Folder Listing window.
The example below indicates what is displayed if the flying sites root or top-level
folder is highlighted. Regardless of what is selected, the Properties are all very similar
in nature and in their method of modification.

An asterisk to the left of an item indicates that it has been modified. Right clicking the
item will bring up the Restore Original Value or Set to Default Value options.

54

Object Palette Window-

The Object Palette window is used to add a new object or objects to the airport. The
object window consists of two separate sections: the preview box in the top section of
the window, and the objects list in the bottom section.

All objects are grouped according to their root directory. Within the root directory the
grouping is further refined. For example, you will find all available benches in the
Benches, Chairs and Tables group. This, of course, assumes that you are utilizing the
Product, Type, Name or Type, Name as determined by the Add Object Grouping
Selection in the Options menu.
Each object group is preceded with a [+] (plus) and an icon. The [+] (plus) indicates
that there is another expansion level, or selection, available to you. Clicking on the [+]
(plus) or double-clicking the respective root directory name (e.g., RealFlight G4) will
bring forward the pull-down menu of the items contained within the specified folder.
If, for example, you wanted to add a bench to the current airport, take the following
steps:

55

1. Click on the [+] (plus) icon in front of the Benches, Chairs and Tables group (or,
double-click the group name itself). This reveals the next expansion level to you.
2. From this expansion list, select the Bench object. The selected object appears in
the preview box.
3. Click the Add button, which adds the object to the scene.
You will find additional information pertaining to object placement, positioning, etc., in
the Properties section of this chapter.
You may use any one of several available methods to change the location of an object
in the airport. To use the drag and drop method, click on the object to highlight it, as
shown below. Once you have highlighted the object, press and hold the mouse
button. Move the mouse to the desired location and then release the button to drop
the object in the new location.

Alternatively, with the object highlighted, right click the mouse elsewhere in the
scenery. This brings up a pop-up menu with several options available to you. To
move the selected object, point the mouse to the location that you desire and click the
Move Here option.

56

G4 also allows you to easily replicate the selected objects. To do so, hold the Ctrl key
down, click and hold the mouse button and use the mouse to drag the object to a new
location. You will see that the original object stays in place. Release the mouse button
and the Ctrl key to drop the new item in place.
Once you have added an object to the airport, you can modify it freely. Refer to the
Properties Window Object Selection section for information on how to do so.
Pilot Preview-

This window provides you with the ability to view the scene from the pilots
perspective. It is very useful when editing PhotoField airports.

The number of pilot perspectives available to you varies; dependent upon the selected
scene. For example, RealFlight Ranch offers: Runway Center, Runway End and
Helipad as the viewing options. To select amongst these options, open the Spawn
Folder in the Folder Listing. Use the up/down arrow keys on the keyboard or the
mouse to select the desired perspective.
It is also possible to modify the selected vantage points. For example, you may Zoom
In and Out, or simply scan the horizon. Note that in order to modify the vantage
point, the Pilot Preview window must be the active window. To ensure that the Pilot
Preview window is the active window, simply click on, or in, this window.

57

To magnify the view or zoom in on the selected item, press the [+] (plus) key on the
keyboard. Each time you press the [+] (plus) key or select the Zoom In menu item,
the zoom level increases incrementally.
To decrease the magnification, or zoom away from the selected item, press the [-]
(minus) key on the keyboard. Each time you press the [-] (minus) key or select the
Zoom Out menu item, the zoom level decreases incrementally.
In most cases, you can also use the scroll wheel on the mouse to zoom in and out on
the scenery
RealFlight also allows you to scan the scene. To do so, press and hold the mouse
button. Moving the mouse will shift the scenery.

Create New Airport

This menu enables you to create an entirely new airport, starting with a fresh canvas.
The FlexiField flying site editor provides you with virtually unlimited editing options,
limited only by your imagination.

The options available to you when creating an airport are identical to those found in
the section pertaining to the airport editor above. As such, we will avoid duplicating

58

these instructions. Instead, we encourage you to experiment with the options, settings
and choices as you see fit.
After you have finished creating your airport, click the file menu and save the airport.
The airport name will appear in your RealFlight G4 directory for future use.

59

Capture Screenshot
Just like the perfect photo opportunity at the local flying field, RealFlight G4 offers the
chance to snap off screenshots. Captured screenshots are great to share with friends,
add as your desktop wallpaper, or put on the Internet for the world to see.

To snap a screenshot, click the Capture Screenshot menu item. Alternatively, press
the Tab key on the keyboard.
Screenshots are stored in the My Documents folder.

60

Mute/Unmute Audio
At times, you may want to fly without any sound. Choose this menu item to mute the
audio. Select it again to activate the sounds.

61

Environment
The Environment menu item has a number of sub menus that allows you to adjust the
sun location and wind settings.

Sun-

RealFlight G4 gives you the ability to adjust the position of the sun in the sky.
By changing the Azimuth, you can rotate the sun around you. Change the
Inclination to adjust how high in the sky the sun should be, or turn day into
night by moving the sun below the horizon.

62

The sun settings are not applicable at PhotoField flying sites.

Adjusting the Sun Azimuth-

If you customize an airport, and find that the sun is always in your
flight path, adjusting the suns Azimuth is a good way to move it
around the sky, out of your way.
To adjust the Azimuth, select the Sun menu. This will bring forth the
Azimuth and Inclination options. Highlight the Azimuth menu item
in the pull-down selections. To rotate the sun to the right, click
Increase. Clicking Decrease will rotate the sun to the left.
Alternatively, you may increase or decrease the Azimuth by pressing
Shift + Home or Shift + End.
When altering the Azimuth, the simulation temporarily displays the
new location in the lower left corner of the window.
Adjusting the Sun Inclination-

To position the sun higher in the sky, or set it below the horizon,
modify the Inclination.

63

To adjust the Inclination, select the Sun menu. This will bring forth
the Azimuth and Inclination options. Highlight the Inclination menu
item in the pull-down selections. To raise the sun higher into the sky,
click Increase. Click Decrease to lower the sun, or to set it below the
horizon to make it night time.
Alternatively, you may increase or decrease the Inclination by pressing
Shift + Page Up or Shift + Page Down.
When altering the Inclination, the simulation temporarily displays the
new location in the lower left corner of the window.
At night time, RealFlight G4 will automatically turn on the lighting
effects on objects and aircraft that offer the lighting abilities.
Wind-

RealFlight G4s TruFlo Wind Dynamics offers the most realistic wind model
of any R/C simulator. Its five components work together to capture this
complex, ever-changing force with unmatched realism. Just as it would at the
field, your model will encounter a variety of wind forces as it soars across the
skies in RealFlight. Sailplane enthusiasts will appreciate the lifelike effect of the
winds as they follow the drafts on the slopes and hills of G4.

64

RealFlight offers you the ability to adjust both the speed and direction of the
wind. To access the Wind settings, click on the Simulation menu followed by
the Wind menu item. Several methods may be utilized to adjust the wind
speed and direction.
Adjusting the Wind Direction-

RealFlight G4 allows you to alter the direction (expressed in degrees)

of the wind. This function is perfect for practicing crosswind landings.
Selecting the Wind menu item brings up the Speed and Direction
options. To adjust the wind direction, highlight the Direction menu
item in the drop-down selections. To increase the degree of wind
direction, click on the Increase option in the drop-down selections.
Likewise, clicking the Decrease option lowers the degree of wind
direction. The wind direction degree increases and decreases in 15degree increments.
You may also adjust the Direction through the Settings menu item.
This method allows you to adjust the direction in one-degree
increments.
Alternatively, you may increase the angle of the wind direction by
pressing the Home key on the keyboard. To decrease the angle of the
wind direction, press the End key on the keyboard.
When altering the wind direction, the simulation temporarily displays
the new wind direction in the lower left corner of the window.
Adjusting the Wind Speed-

Increasing the wind speed is an ideal way to learn to fly in the lessthan-perfect wind conditions that frequently occur at an R/C field. To
adjust the speed of the wind, select the Wind menu. This will bring
forth the Speed and Directions options. To adjust the speed of the
wind, highlight the Speed menu item in the pull-down selections. To
increase the speed of the wind, click on the Increase option in the
pull-down selections. Clicking the Decrease option reduces the wind
speed.
Alternatively, you may increase the wind speed by pressing the Page
Up key on your keyboard. To decrease the speed of the wind, press
the Page Down key on your keyboard. Each time the Page Up or
Page Down key is pressed the wind is increased or decreased
incrementally.

65

When altering the wind speed, the simulation temporarily displays the
new wind speed in the lower left corner of the window.
Alternatively, you may adjust the Wind through the Settings menu item.
For information on how to do so, please refer to the Settings section on page
76.

Flight Failures
RealFlight G4 offers the ability to simulate common failures for your aircraft. This
feature aids in teaching you how to remain calm and react appropriately when an actual
failure occurs at your R/C field. RealFlight G4 allows you to determine both the types
of flight failures that you will face as well as how often those failures will occur.

Adjust the Rate of Occurrence-

There are several methods available to adjust the frequency at which flight
failures will occur. To use the first method, click on the Simulation menu
followed by the Flight Failures menu item, and then the Frequency menu
item. This brings up a sub-menu as shown in the screen below. Once the sub-

66

menu is visible, simply mouse click on one of the options in the pull-down
menu.

Alternatively, you can adjust the rate of occurrence in the Settings menu
item. To access this menu item, click on the Simulation menu followed by
the Settings menu item. Next, click on the Flight Failures listing. You
can bring forth the Flight Failures options by clicking on the [+] (plus) or by
double-clicking on the Flight Failures listing itself. To adjust the frequency of
occurrence, click on the value as indicated in the column to the right of the
probability indicator.
The Settings section on page 76 discusses the Flight Failures options in detail.
If you do not wish to experience any flight failures, click the Never option in
the drop-down menu. Conversely, if you wish to gain a great deal of
experience at handling emergencies, click the Always option. The Always
options means that each time you reset the aircraft, something is guaranteed to
go wrong. Maybe not right away an engine failure will usually wait until
some entirely inconvenient time to reveal itself, but it will happen. The Rarely
option corresponds to roughly a 5% chance per reset that something will fail.

67

Selecting the Type of Flight Failures-

As noted previously, RealFlight G4 also allows you to determine the type of

flight failures that you will experience within the simulation. To do so, click
the Simulation menu followed by the Flight Failures menu item. Next,
select Enable to bring forth the list of available flight failures. If an item has a
check mark next to it, then that flight failure is enabled. To disable the flight
failure, click on it with the mouse.

Cause Flight Failure-

This feature causes a flight failure to occur. To access this menu item, click on
the Simulation menu, and then click on the Cause Flight Failures menu
item. As an alternative, press the F key on your keyboard to cause a flight
failure.

68

Import
The Import menu item allows you to utilize, or import, content created by other users.
There are three types of files that are associated with RealFlight G4; each will be
covered in the section that follows.

69

KEX-

Knife Edge Software has created a plug-in, or software module that functions
with popular 3D modeling tools to create subject matter for the RealFlight
software.
The KEX importer is used to bring the model from the plug-in into the
simulation itself.
For more information, see: http://www.knifeedge.com/KEmax/
Raw Panoramic Image-

This file type refers to the panoramic image that helps generate the PhotoField
flying sites. This option allows you to create a PhotoField using a panoramic
image that you may have downloaded or created yourself. It works best with
large images (8000x4000) that are equirectangular, spanning 360 degrees
horizontal by 180 degrees vertical. Click on the Raw Panoramic Image
selection to import an image into the simulation. Browse to the location of the
image you would like to import. The image may be either a bitmap (.bmp),
targa (.tga) or a JPEG (.jpg) file extension.
Once you have located the appropriate folder and desired image, double-click
the image. Alternatively, select this image and click Open. The conversion

70

process can take several minutes for large images. When the process is
complete, G4 will automatically create a new PhotoField airport that uses your
newly imported image.
To edit the new PhotoField airport (for image alignment, object placement,
etc.), access the Airport Editor. To do so, click the Simulation menu,
followed by the Create New Airport menu item. To see the image from
the pilots perspective, refer to the Pilot Preview window. This will make it
easier to place objects and adjust the image correctly. If necessary, adjust the
image using the Panoramic Image Y Alignment, Panoramic Image X
Alignment and/or the Panoramic Image Facing options located in the
Properties window.
RealFlight Archive (RFX, G3X)-

RFX is the file extension that is used for all files exported from RealFlight G4.
This menu option allows you to import an RFX file. You will use this for all
files that you have downloaded. There is nothing special you need to know
about the file beforehand; the RFX importer handles all types of content,
including planes, color schemes, airports, PhotoFields, and recordings.
After choosing the Import menu item followed by the RealFlight Archive
(RFX, G3X), you will be presented with an Open file dialog. Use this dialog to
find the file that you want to import. Double-click the file or click the file and
click Open. The import process will start immediately and once its finished
you will see a message confirming its success.
This menu item also allows you to import G3X files used in RealFlight G3 and
G3.5.

71

Export
The Export menu item allows you to share user-created content. It is provided in the
menu as a shortcut to using the Manage User Files dialog.

G4 users may share the following items: Color Schemes, Aircraft Variant, Entire
Aircraft, Airport and Panoramic Images. If one or more of these options on the list is
grayed out, it is because the currently loaded color scheme, aircraft, or airport is part of
the simulation by default and not available for export.
Once any of these items are exported, you can then share them with friends or the rest
of the RealFlight community. The best choice is to upload the files to the RealFlight
swap site found at:
http://www.knifeedge.com/forums/downloads.php?
Color Scheme-

This option allows you to share the current aircraft color scheme (a.k.a. trim
scheme) with other RealFlight users.
To export a Color Scheme, select the Export menu item followed by the
Color Scheme option. A save dialog will appear so that you can choose

72

where you would like to save the exported color scheme and determine the
filename. After saving, a message will appear on-screen advising you whether
or not the export was successful. This message will also list the location and
name of the file that was exported.
Aircraft Variant-

This option enables you to export an aircraft that has undergone structural
modifications such as lengthened wing span, more prop thrust, different
airfoils, etc. It is important to note in addition to any wire frame modifications,
the Aircraft Variant file option also includes any modifications to the aircraft
powerplant, batteries, etc.
To export an aircraft variant, select the Export menu item followed by the
Aircraft Variant option. A save dialog will appear so that you can choose
where you would like to save the exported color scheme and determine the
filename. A verification message will appear on-screen advising you whether
or not the export was successful. This verification message will also list the
location and name of the file that was exported.
Entire Aircraft-

This option enables you to export the entire contents of an aircraft such as
trim scheme, structural changes, etc.
To do so, select the Export menu item followed by the Entire Aircraft
option. A save dialog will appear so that you can choose where you would like
to save the exported color scheme and determine the filename. A verification
message will appear on-screen advising you whether or not the export was
successful. This verification dialog will also list the location and name of the
file that was exported.
Airport-

This option enables you to export a modified airport. Note that any custom
panoramic image you may be using with this airport will not be exported. To
export an airport with a custom panoramic image, use the Airport (include
Panoramic Image) option.
To export an airport, select the Export menu item followed by the Airport
option. A save dialog will appear so that you can choose where you would like
to save the exported color scheme and determine the filename. After saving, a
verification message will appear on-screen advising you whether or not the
export was successful. This verification message will also list the location and
name of the file that was exported.

73

Airport (include Panoramic Image)-

This option enables you to export an airport along with its custom panoramic
image. To do so, select the Export menu item followed by the Airport
(include Panoramic Image) option. A save dialog will appear so that you
can choose where you want to export the airport and what you want to name
the file. A verification message will appear on-screen advising you whether or
not the export was successful. This verification message will also list the
location and name of the file that was exported. You may then upload the
exported file to a web site for others to enjoy.

Manage User Files

The Manage User Files menu item allows you to modify the new user content that you
have added to the simulation. You will find that the Manage User Files menu item is a
handy tool as it maintains all such files in one, easy to find location.

The Manage User Files dialog allows you to copy, rename, delete, or export
any custom resource that exists in the simulation. It is important to note that
the various Manage User Files buttons will be inactive until a modification to

74

one of the files exists. That is, this menu item is only utilized to modify usercreated items. It will not allow you to modify the airports or vehicles included
in the RealFlight Generation 4 software.
Copy-

This option duplicates the information and data pertaining to the currently
selected item. If, for example, you wish to duplicate a flying site located in the
User Files, click the Copy button.
Once you have copied the file, enter a name for the new item. Using our
previous example, simply rename the flying site as desired. This new name will
then be used in the Select Airport dialog.
Rename-

This option is utilized to rename a user-created item.

To do so, highlight the desired item (flying site, etc.) and click Rename. Enter
the desired name for the item in the dialog provided. The item will now
appear in its respective list of offerings with the new name.
Delete-

This option is utilized to delete an item entirely. All files associated with the
item will be removed from your computer.
Again, it is important to note that users are only allowed to delete items which
they, or other users, have created. That is, you are not allowed to delete default
items that are included with the software.
To delete a user-created item, select the item in the User File menus and click
Delete. If you wish to delete this item, click Yes in the verification dialog.
Please note: once deleted this resource will no longer be available in the
simulation.
Export-

This button is used to Export, or place the airport/aircraft/recording in a

location so that the user may share it with others. If you have created
interesting or unusual content, we encourage you to share your designs with
other RealFlight users. The more content that is shared the more enjoyment
everyone will experience.
To export a user-created item, select the respective item in the User File menus
and click Export. A verification dialog will appear on-screen advising you
whether or not the export was successful and the location and name of the file

75

that was exported. You may upload the exported file to a web site, move it to
another computer, or email it for others to enjoy.

Settings
The Settings options are an integral part of the G4 software. This menu item allows
you to adjust a multitude of features and functions within the simulation.

To access this menu item, click on the Simulation menu followed by the Settings
menu item. The Settings dialog will appear, showing the available options.

76

The Settings that are available to you are as follows:

Audio

Camera

Console

Flight Failures

Graphics

Multiplayer

Physics

Wind and Weather

Audio-

Audio settings are split into two different categories which are as follows. Double-click
on the Audio name, or click on the [+] (plus) to expand the list and show the Audio
options.

77

Application-

The Application section controls the sound over the entire simulator.

Volume (%) - This setting adjusts the master volume level for the entire
simulator.

Sound Enabled - Choosing No for this option will mute all sounds for the
simulator.

Sounds-

The Sound settings control the various options related to the miscellaneous
sounds within the simulation. RealFlight allows you to make modifications to
the various sounds based upon your preferences.

78

For each type of sound that is adjustable, there are two parameters that can be
changed. First is the Volume, which is a percentage of the overall volume.
The second is whether the sound should be enabled or muted.
The different sound types are:

Aircraft affects aircraft related sounds such as servos.

Airport affects the ambient sounds around the airport.

Collision adjust these to affect the crashing sounds associated with

collisions.

Effects this represents the miscellaneous sounds that dont fit into
any other category.

Engine adjust this to affect the motor and engine sounds.

Voiceover these parameters adjust the voiceovers used for the

Virtual Flight Instructions.

Walk adjusts this to control the walking sound when moving the
camera angle.

79

Wind this affects the sound produced by the wind.

Camera-

The camera options available to you are designed to enhance the field of view when
utilizing the Keep Ground in View zoom mode. For additional information on this
option, please refer to the View menu section of this manual.

Minimum Field of View (deg)-

This setting determines the absolute minimum field of view when utilizing the
Keep Ground in View zoom option.
To adjust the minimum field of view, click the existing value. Next, enter the
desired value either directly from the keyboard or via the mouse wheel.
Camera Lag (%)-

This controls how quickly the camera reacts to the aircrafts movements. If
the lag is set to zero, the camera always looks directly at the aircraft. At all
other values, the camera will have a spring-like reaction to the aircraft during
flight.
At very high values, the camera hardly ever looks directly at the aircraft, and
often the aircraft will fly off the screen as the camera tries to catch up. At
lower values, the effect is very subtle and yet still softens the camera movement

80

enough so that minor changes in the aircrafts speed/position are more

noticeable.
Please note: these settings apply to fixed view cameras only. They are not
applicable to the cockpit or chase views.
Console-

The Console option has a number of sub-categories that allow you to perform
modifications to the messages that appear on-screen while running the simulator. It
also offers two parameters that affect all the sub-categories.

Show At Most-

This numerical value indicates the maximum number of messages that will
appear on your screen at any given time. When the maximum number is
surpassed, an older message will be removed and the most recent message will
take its place on-screen.
To adjust the number of messages displayed on-screen at one time, click on
the value as indicated in the column to the right of the Show At Most
indicator. Input the desired value directly from the keyboard or use the mouse
wheel.

81

Clear on Reset-

This setting controls whether all the on-screen messages are cleared when the
aircraft resets. This prevents the screen from becoming overly cluttered with
messages and information.
Using either the up/down arrow keys on the keyboard, or the mouse, select
either Yes (messages automatically clear) or No (messages remain on-screen
after a reset) from the pull-down listings. If using the up/down arrow keys,
press Enter to finalize your selection.
Double-clicking on the Console name or clicking on the [+] (plus) will bring forth
the following options:

Instructions

Notifications

Warnings

Errors

Chat Messages (Sent)

Chat messages (Received)

Commands

Each of the System Messages screens is independently adjustable and may be tailored
to suit your personal preferences. For information on how to do so, please read the
following section.
Instructions-

As the name suggests, modifications will affect only the System Instructions.

82

Font Size-

This option allows you to adjust the font size for the messages
pertaining to the instructions. Please note: this only affects the
Instructions. It does not affect any other system messages.
To access the Font Size options, click on the value shown in the
respective column. The desired values may be input directly from the
keyboard or modified using the mouse wheel.
Foreground Color-

This option allows the user to adjust the color of the foreground for
the Instructions messages.
To access the options pertaining to the foreground color, click on the
current value. Click the more options button (the gray folder with
the ellipsis) to bring forth the palette of available colors. This will
reveal a screen that appears as follows:

83

To select a color, click the desired color on the palette. If you wish to
make a custom color, click the Define Custom Colors button and
create the color or colors to suit your tastes. Click OK to finalize the
selection. The selected color will be reflected immediately in the value
column.
Background Color-

As with the Foreground Color, this setting allows the user to adjust the
color of the background for the Instructions messages.
To access the options pertaining to the background color, click on the
current displayed color.
Click the more options button (the gray folder with the ellipsis) to
bring forth the palette of available colors. To select a color, click the
desired color on the palette. If you wish to make a custom color,
click the Define Custom Colors button and create the color or colors
to suit your tastes. Click OK to finalize the selection. The selected
color will be reflected immediately in the value column.
Background Alpha (%)-

This option adjusts the transparency of the text background for the
message.

84

The desired values may be input directly from the keyboard or

modified using the mouse wheel. The higher the value, the more
transparent the text background will become.
Message Duration (sec)-

This option adjusts the length of time that a message remains onscreen before it disappears.
You may input desired values directly from the keyboard or modify
them using the mouse wheel. Of course, the higher the value, the
longer the message remains on-screen.
Enabled-

This option determines whether Instructions messages are displayed or

not.
To determine whether this is enabled, click on the respective value
indicator. Using either the up/down arrow keys on the keyboard, or
the mouse, select either Yes (Instructions messages are enabled) or
No (Instructions messages are disabled) from the pull-down listings. If
using the up/down arrow keys, press Enter to finalize your selection.
Notifications-

To select the Notifications options, click on the Notifications name. These

options function in the same manner as the options for the Instructions
messages, except that they only affect Notification messages.

85

Warnings-

This option determines the settings for the system warning messages.

To select the Warnings options, click on the Warnings name. These options
function in the same manner as the options for the Instructions messages,
except that they only affect Warning messages.

86

Errors-

This option allows you to modify the behavior of system error messages.

To select the Errors options, click on the Errors name. These options
function in the same manner as the options for the Instructions messages,
except that they only affect Error messages.

87

Chat Messages (Sent)-

This option allows you to modify the appearance of text that you type for chat
messages during multiplayer sessions.

To select the Chat Messages (Sent) options, click on the Chat Messages (Sent)
name. These options function in the same manner as the options for the
Instructions messages, except that they only affect Chat Messages (Sent)
messages.

88

Chat Messages (Received)-

This option allows you to modify the appearance of text that you receive from
other players during multiplayer sessions.

To select the Chat Messages (Received) options, click on the Chat Messages
(Received) name. These options function in the same way as the options for
the Instructions messages, except that they only affect Chat Messages
(Received) messages.
There is one additional parameter available for this option called Play Sound.
This allows you to set whether a sound is heard when an incoming chat
messages arrives.

89

Commands-

This option allows you to modify the appearance of commands typed in the
console screen.

To select the Commands options, click on the Commands name. These

options function in the same manner as the options for the Instructions
messages, except that they only affect Commands messages.

90

Flight Failures-

To adjust the Probability options or the Notify When settings, click on the Flight
Failures root directory.

Double-click on the Flight Failures name or click on the [+] (plus) to expand the list
and show the Flight Failures options. RealFlight defaults all Flight Failures to enabled
(active). Each item may be enabled or disabled individually. To disable a specific flight
failure, click on the respective failure located within the pull-down list. Next, click on
the Yes value as indicated in the value column. This brings forth the Yes/No pulldown list. To disable the respective failure, simply choose the No option. For
example, to disable the Reverse Servo flight failure:
1. Select the Reverse Servo option in the Flight Failures sub-menu
2. Click the Yes in the right hand pane
3. Select No from the pull-down list
Probability-

To adjust the frequency of occurrence, click on the value as indicated in the

column to the right of the probability indicator.
If you do not wish to experience any flight failures, select the Never option in
the drop-down menu. Conversely, if you wish to gain a great deal of
experience at handling emergencies, click the Always option.

91

Notify When-

This setting allows you to determine if, or when, RealFlight notifies you as to
the flight failure experienced.
To adjust the settings of this feature, click on the value as indicated in the
column to the right of the Notify When indicator. Your options are:
After Flight - RealFlight will advise you as to the flight failure experienced
upon the completion of the flight.
Before Flight - RealFlight will tell you which flight failure you are about to
experience before the flight begins.
Never - RealFlight G4 will never advise you as to the flight failure that you
have experienced, or are about to experience. A little mystery is a good thing.
On Failure - RealFlight will tell you about the flight failure just as it occurs.
The different Flight Failures available in RealFlight G4 are as follows:

Reverse Servo - The travel direction of one of your servos is reversed.

Kill Engine - The engine will fail or quit in flight, which means that you will have
to perform a deadstick landing or autorotation.

Servo Stuck - A servo will become fixed, or stuck, in a certain position.

Servo Trim - A servo alters the trim settings, modifying the flight control position.

Channel Swap - This failure simulates the effect of inadvertently swapping two
channels. As an example, you may find that your rudder controls the throttle, and
vice versa.

Radio Lockout (PCM) - The receiver will experience intermittent radio dropouts
during which time the aircraft will fail to respond to control inputs.

Radio Interference (FM) - The receiver will experience intermittent radio

interference during which time the servos will behave erratically.

Radio Range - The receiver will experience interference proportional to the

distance between the pilot and the aircraft. If the aircraft is close to the pilots
position, the range problems will be minimal, increasing as the aircraft gets farther
away.

92

Reverse Channel - One of the channels, selected at random, will operate in reverse
direction.

Structural Integrity This failure determines how strong the aircraft is and if parts
could break off during flight. This failure also has a parameter called Allow
Multiple Failures which allows this flight failure to be triggered more than once
during a flight.

Graphics-

Double-click on the Graphics name or click on the [+] (plus) to expand the menu
and display the various Graphics options available to you.
Quality Options-

The Quality options are quite useful in fine-tuning your simulator to ensure
that it runs as efficiently and realistically as possible on your PC. Use the
settings in the Graphics options to obtain the perfect blend of optimal visuals
and performance from your PC. If you are experiencing slow frame rates or
other performance issues, it may be prudent to turn down some graphics
quality options.

Note that many of the adjustments will not take place immediately. In many
cases, you will need to restart the simulator in order for the option to take
effect.

93

Clouds-

This option determines whether your flying sites will include clouds in
the skyline.
Click on the respective value indicator. From the pull-down options
select either Yes (clouds will be present) or No (clouds will not be
present).
Particles-

This option determines whether RealFlight will utilize particles such as

engine smoke.
Click on the respective value indicator. From the pull-down options
select either Yes (G4 will display smoke) or No (G4 will not display
smoke).
Scenery Objects-

This option determines whether the simulation displays background

objects such as buildings, rocks, benches, etc. If Yes is selected, the
background objects will be present. If No, the background objects will
not appear in the simulation.
To change this setting, first click on the respective value indicator.
From the pull-down options select either Yes or No.
Shadows Enabled-

The Shadows option determines whether the simulation displays

shadows.
To change the Shadows setting, click the value located to the right of
the Shadows name. Next, click Yes to display the shadows or No to
eliminate shadows from the simulation.
Terrain Detail-

This option determines whether or not RealFlight G4 displays the

details found in the textures. Modify the Terrain Detail setting by
clicking on the value located to the right of the Terrain Detail name.
Click Yes to display the terrain detail texture or No to eliminate the
terrain details.
Trees-

The Trees setting determines whether RealFlight G4 display trees. To

change the Trees setting, click the value located to the right of the
Trees. Select No if you do not wish to display the trees in your
simulation. If you wish to view the trees during flight, select Yes.

94

Please note: the display of trees does have an effect on the frame rate
of your simulation.
Wind Field Indicators-

This parameter determines whether or not RealFlight displays the

wind field indicators that are present at select airports.
Post-processing: Bloom-

The Bloom effect will cause lighter colors or lights to bleed into
neighboring parts, enhancing their perceived brightness.
Please note: the Bloom effect does have an effect on the frame rate of
your simulation.
Post-processing: Night Flying Glow-

This option affects whether lights for night flying glow, causing the
objects to appear brighter.
Please note: the Night Flying Glow effect does have an effect on the
frame rate of your simulation.
Foliage Density (%)-

This setting determines the density and drawing time of the trees and
the grass. Lowering the percentage will ensure that the scenery is
drawn faster. Again, if you are experiencing low frame rates, lowering
this value will speed up the simulation.
To adjust the percentage, click on the value located to the right of the
Foliage Density (%) name. Enter the desired input directly from your
keyboard, or use the mouse wheel.
Optimize Shadows-

This parameter will allow shadows to be rendered faster, increasing the

frame rate, if your video card allows it. If you see problems such as
flickering with shadows, try disabling this option.
Water Quality-

This setting specifies the quality of the water in the simulation.

RealFlight G4 attempts to automatically optimize the settings for your
PC. However, it may be necessary for you to perform some manual
fine-tuning in order to obtain the best possible performance.
To modify the quality of the water, click on the value indicated in the
column to the right of the Water name. Select the desired level for
your simulation from the pull-down list. The Highest setting will

95

render the best water, but it requires additional processing power. If

your frame rate is low, we suggest you reduce the water quality.
Shadow Quality-

This setting specifies the quality of the shadows in the simulation.

RealFlight G4 attempts to automatically optimize the settings for your
PC. However, it may be necessary for you to perform some manual
fine-tuning in order to obtain the best possible performance.
To modify the quality of the shadows, click on the value indicated in
the column to the right of the Shadows name. Select the desired level
for your simulation from the pull-down list. The Highest setting will
render the best shadows, but it requires additional processing power.
If your frame rate is low, we suggest you reduce the shadow quality.
Particle Quality-

This setting adjusts the quality of the smoke, debris and other small
objects during the simulation. If the frame rate drops when the smoke
is thick, try lowering the quality of the smoke until you achieve an
acceptable frame rate.
To do so, click on the existing particle quality. Next, from the pulldown menu, select the desired quality level.
Streamer Quality-

This setting adjusts the quality of the streamers during the simulation.
If the frame rate drops when flying an aircraft with streamers, try
lowering the quality of the streamers until you achieve an acceptable
frame rate.
To do so, click on the existing streamer quality level. Next, from the
pull-down menu, select the desired quality level.
Texture Quality-

Use this setting to add the realistic textures to the items and various
other objects found in the simulation.
To do so, click on the existing texture quality level. Next, from the
pull-down menu, select the desired quality option.
Please note: you must restart the simulation for the new setting to take
effect.
Misc. Graphics Quality-

This setting adjusts the quality level of miscellaneous items in your

simulation.

96

To alter the Miscellaneous Graphics level, click on the value located to

the right of the Misc. Graphics name. Next, select the desired level to
utilize for the graphics.
Please note: you must restart the simulation for the new setting to take
effect.
Brightness (%)-

This setting adjusts the brightness of the ambient lighting found in the
simulation. If dark colors appear to be overly dark, increase the
brightness percentage.
To adjust the brightness percentage, click on the current brightness
percentage. Enter the desired value directly from the keyboard or use
the mouse wheel.
Contrast (%)-

The contrast percentage brightens the lighter colored items in the

simulation. It does not affect the darker items in the simulation.
To adjust the contrast percentage, click on the contrast percentage.
Enter the desired value directly from the keyboard or use the mouse
wheel.

97

Hardware-

The Hardware settings are used to adjust the non-software settings to achieve
the best possible simulation for your PC.

Graphics Adapter-

The Graphics Adapter is the device that RealFlight utilizes to run the
simulation, generically referred to as a video card. Most PCs have
only one video card; however, some PCs are equipped with multiple
cards.
To determine if your PC has an additional video card available to you,
click on the video card information located in the values column to the
right of the Graphics Adapter name. If multiple cards appear in the
drop-down selection there is another option for you. If not, your PC
is equipped with only one video card.
Graphics Device-

Some video cards offer multiple devices. HAL (Hardware Abstraction

Layer) is the preferred device to use for the graphics rendering. In
general, you should never need to modify this setting.
To determine if your PC offers alternative devices, click on the value
indicated in the column to the right of the Graphics Device name.

98

Full Screen-

This option determines whether RealFlight will run using the entire
monitor screen for the simulation. If you decide to run in the Full
Screen mode, RealFlights menus will not appear on the screen.
To access the menu while in Full Screen mode, press either the ESC
key or the ALT key on the keyboard.
To adjust the Full Screen option, click on the value as indicate in the
column to the right of the Full Screen name. From the pull-down
menu, select Yes to run in Full Screen or No to run in the Windowed
mode.
Alternatively, you may access the Full Screen mode by pressing the Alt
and Enter keys simultaneously on the keyboard. To exit Full Screen
mode, press the ALT and Enter keys simultaneously.
Resolution-

This control adjusts the screen resolution and color depth. If your
frame rate is unacceptably low, you can improve it by reducing the
resolution or color depth. This will reduce some of the rendering
processes required of your video card.
To adjust the resolution for your simulation, click the value indicated
in the column to the right of the Resolution name. Select the desired
level for your simulation from the drop-down list.
Please note: this option is only effective when using RealFlight in the
Full Screen mode.
We suggest that you test a variety of resolutions and color options to
achieve the optimum performance and setup for your system.
Refresh Rate-

The refresh rate is the number of times per second that your monitor
retraces its video display. Your video hardware (monitor and graphics
card) dictates what refresh rates you are able to utilize in the
simulation. As with Resolution, this option is only effective when
running RealFlight in the Full Screen mode.
To adjust the refresh rate, click the value that is indicated in the
column to the right of the Refresh Rate name. If there are multiple
options in this list, you might opt for a lower value to determine if this
improves the frame rate of your simulation.

99

Vertical Sync-

This option dictates where the monitor will draw the next vertical line.
Activating Vertical Synchronization slows the simulation slightly, but it
prevents the tearing of on-screen images.
To adjust the Vertical Sync, click the respective value. Select Yes or
No from the pull-down menu that appears.
Multiplayer-

Settings available here affect multiplayer parameters, either in split screen MultiMode,
or over the internet.

Pilot Name-

This setting allows you to enter a name for the multiplayer sessions. To do so,
click on the value that appears to the right of the Pilot Name column. Click
the more options button (the gray folder with the ellipsis). Enter a name of
your choosing. When satisfied, press the Enter button on your keyboard.
Please note: when participating in a multiplayer session, other players may be
able to view the name you have selected.
MultiMode Screen Layout-

This setting specifies the layout of the screen for the MultiMode option. If you
select Vertical, the computer screen will split in half on its vertical axis. If you
select Horizontal, the computer screen will split in half on the horizontal axis.

100

To select which mode best suits your tastes, click on the value displayed to the
right of the MultiMode Screen Layout column. Next, select either Horizontal
or Vertical from the pull-down options.
Collisions-

The Collisions options allow you to enable or disable the collisions between
aircraft in Multiplayer sessions. If you are connected via dialup, or have a slow
network connection, Select No as this may speed up the performance of the
simulator.
Physics-

The physics options are quite useful in fine-tuning the items applicable to the physics
of your simulated aircraft.

Airplane Physics Quality-

This setting determines the detail level of physics utilized for the airplanes in
the simulation. When the physics level is adjusted to the highest setting, the
simulation performs the aircraft calculations more accurately and more
frequently. Unless you are running the simulation on an older, slower PC, we
suggest using either the high or highest settings. Lowering the physics level
will reduce the quality and detail level used in the simulation, thereby allowing
the simulation to run at a faster rate for slower PCs.
To alter the physics options, click on the value indicated in the column to the
right of the Airplane Physics Quality name. Using either the up/down arrow

101

keys on the keyboard, or the mouse, select the level for your simulation from
the pull-down list. If using the up/down arrow keys, press Enter to finalize
your selection.
Helicopter Physics Quality-

This setting determines the detail level of physics utilized for the helicopters in
the simulation. When the physics level is adjusted to the highest setting, the
simulation performs the aircraft calculations more accurately and more
frequently. Unless you are running the simulation on an older, slower PC, we
suggest using either the high or highest settings. Lowering the physics level
will reduce the quality and detail level used in the simulation, thereby allowing
the simulation to run at a faster rate for slower PCs.
To lower the physics option, click on the value indicated in the column to the
right of the Helicopter Physics Quality name. Using either the up/down arrow
keys on the keyboard, or the mouse, select the level for your simulation from
the drop-down list. If using the up/down arrow keys, press Enter to finalize
your selection.
Unlimited Fuel-

This option determines whether or not your aircraft will run out of fuel. If you
select Yes, the engine will run indefinitely assuming, of course, that you do
not crash. If you select No, the aircraft will indeed run out of fuel. The length
of time required to do so is based upon a number of factors including the
engine utilized and throttle management, just as it would at the flying field.
To determine whether your aircraft will run out of fuel, click on the value
column to the right of the Unlimited Fuel option. Using either the up/down
arrow keys on the keyboard, or the mouse, select either Yes or No from the
pull-down listings. If using the up/down arrow keys, press Enter to finalize
your selection.
Use Metric Units-

This option determines the unit of measurement for the various displays found
in the simulation. RealFlight defaults to display measurement in SAE units.
You can easily change this to use metric units.
To do so, click on the value column to the right of the Use Metric Units name.
Using either the up/down arrow keys on the keyboard, or the mouse, select
either Yes or No from the pull-down listings. If using the up/down arrow
keys, press Enter to finalize your selection.
Physics Speed-

Expressed as a percentage, this value controls the time scale of the simulation.
Reducing the value allows you to create a slow-motion effect. This is useful

102

when learning new skills or maneuvers, as you may slow the aircrafts reaction
time.
It is important to note that these adjustments do not affect RealFlight during
multiplayer sessions or events.
To adjust the Physics Speed, click the value. Enter the desired value directly
from the keyboard or use the mouse wheel.
Automatic Reset Delay (sec)-

This setting will force RealFlight to automatically reset the aircraft after a crash
where a piece of the aircraft has broken off.
To adjust the Reset Delay, click the respective value. Enter the desired value
directly from the keyboard or use the mouse wheel.
Wind and Weather-

The wind and weather options control the atmospheric conditions encountered in the
simulation. You can adjust these to match the conditions typically found at your local
flying site.
Global Wind-

These options determine the global wind conditions for the current airport.
Please note: the adjustments made here will temporarily override the airports
default values. Upon selecting an alternative airport or closing RealFlight, the
default values will be restored.

103

Wind Direction (deg)-

To adjust the wind direction, click on the value indicated to the right
of the Wind Direction name. Next, input a numerical value between 0
and 359 degrees to modify the wind direction. Alternatively, the
mouse wheel may be used to alter the input value.
You may also adjust the wind direction from the keyboard. Press the
Home key to increase the wind direction. The End key will reduce the
direction of the wind.
The direction that the wind comes from is expressed in degrees; where
0 is north, 90 is east, 180 is south and 270 is west. It is also possible to
adjust the wind direction to any angle in-between.
Wind Velocity (MPH)-

This setting adjusts the average winds that prevail over the entire
simulation. The velocity here is the speed of the wind approximately
6.5 feet (2 meters) above the terrain. RealFlight G4s wind gradient
ensures that the wind below this level is slightly slower and that the
wind at higher altitudes is faster.
To adjust the wind velocity, click on the value indicated to the right of
the Wind Velocity (MPH) name. Next, input a numerical value
between 0 and 50, using either your keyboard or the mouse wheel.
This will be the wind speed in MPH.

104

You may also increase/decrease the wind velocity in smaller

increments by pressing the Page Up/Page Down keys on the
keyboard.
Wind Variation (%)-

This adjustment represents the variation in the wind speed and

direction in relation to the average speed. Just as the winds that you
experience at the local field are not constant, neither are the winds in
RealFlight.
To adjust this variable, click on the value indicated to the right of the
Wind Variation (%). Using either your keyboard or the mouse wheel,
input a numerical value between 0 (unchanging) and 200. A higher
value produces more dramatic changes in the wind.
Wind Gust (%)-

This value represents the change of the wind speed and direction
corresponding to a proportion of the wind speed it calculates in one
second.
To adjust this variable, click on the value indicated to the right of the
Wind Gust (%). Using either your keyboard or the mouse wheel,
input a numerical value between 0 (no changes) and 100 (large
changes).
Turbulence System-

RealFlights wind model is so authentic that it even recreates the turbulence

which your aircraft will experience when out at the field.

105

Turbulent Layer Height-

Use this setting to mimic the turbulence level at your local flying site.
This setting represents the maximum height above the ground at
which your aircraft will experience the effects of G4s turbulent winds.
To adjust the Turbulent Layer Height settings, click on the value
indicated in the column to the right of this respective option. The
desired values may be input directly from the keyboard or modified
using the mouse wheel.
Turbulence Strength Proportion (%)-

This option allows you to adjust the strength of the medium-level

turbulence. Since this setting represents a median, some turbulence
will be more severe than this, and some turbulence will be less
noticeable.
To adjust the Turbulence Strength Proportion (%) settings, click on
the value indicated in the column to the right of this respective option.
The desired values may be input directly from the keyboard or
modified using the mouse wheel. A value of 0% indicates that there
will not be any mid-level turbulence.

106

Micro-Turbulence Strength Proportion (%)-

This option allows you to adjust the strength of the lower level
turbulence. Some turbulence will be more severe. This is the lowest
level of turbulence that you will experience, however.
To adjust the Micro-Turbulence Strength Proportion (%) settings,
click on the value indicated in the column to the right of this respective
option. The desired values may be input directly from the keyboard or
modified using the mouse wheel. A value of 0% indicates that no
micro-turbulence will occur.

Exit
Use this menu item to exit the program entirely.

107

Airport MRU
If you have previously selected an alternative flying location, or locations, you will note
that it will appear on a list in the Simulation menu. This list is at the very bottom of the
menu and is commonly referred to as a Most Recently Used, or MRU list. It is limited
to the eight most recently selected locations. If you wish to fly at one of these locations
simply click on the respective location and it will begin loading.

108

Chapter

The Aircraft Menu

Offers access to a variety of aircraft related features, functions and options.

licking the Aircraft menu brings forth a pull-down menu similar to the
following screen shot.

The menu items that are available from the Aircraft menu include:

Select Aircraft

109

Edit Current Aircraft

Select Color Scheme

Save Color Scheme As

Remember Aircraft Position

Clear Aircraft Position

Reset Position

Kill Engine

Aircraft MRU

The following sections describe the function and purpose of each of these menu items.

110

Aircraft Selection
When you click on Select Aircraft the following dialog appears:

This dialog allows you to select the aircraft that you wish to fly.
Change aircraft simply by using the InterLink Elite. Press the
Menu/Select button, then, with the airplane tab highlighted press
the Menu/Select button again. This will bring up the Select
Aircraft dialog window. You can continue using the QuickSelect
buttons in this dialog to select a new aircraft, or press Reset to
resume flying without making any changes.
The list on the left of the dialog box displays all of the aircraft available to you. If you
have created any customized aircraft, they will also appear in this list.
By default, the aircraft are listed in files and directories in accordance with the software
from which they were loaded. If, for example, you have installed Expansion Pack 2,
the aircraft from this disc will be listed, alphabetically, beneath the Expansion Pack 2
directory.

111

Click the [+] (plus) or [-] (minus) symbol to reveal or hide the aircraft within these
directories and folders.
Aircraft Selection

Every aircraft has its own unique flying characteristics, special features and functions.
To view an aircraft from the listings, simply use the mouse to click on the aircraft
name. Alternatively, use the up/down keys on the keyboard to scroll through the list,
one aircraft at a time.
The first time an aircraft is selected, G4 creates a collision mesh for the aircraft. This
process may take a few seconds to complete. A progress bar will appear while the
collision mesh is being calculated.
Click the [+] (plus) symbol to reveal the aircraft contained within the folder. Using
either the up/down arrow keys on the keyboard or the mouse, select the desired
aircraft from the listings. If utilizing the up/down arrow keys, click OK to finalize your
selection. Alternatively, if using the mouse, double-click on the aircraft to load it.
Have some fun while youre in the Select Aircraft dialog. Using the mouse, click and
drag the preview screen to point the camera angle to your choosing. Use the scroll
wheel to zoom in or out. Or, move the gimbals to see the control surfaces move. To
resume rotating automatically, right-click the preview screen.
Description/Specifications-

The pane below the Aircraft Preview box shows either the aircraft description or
aircraft specifications. This box provides you with a brief history of the aircraft (if
applicable) and serves to provide you with specific information pertaining to the model
selected.
Using the mouse, select either the Description or Specifications tab.
Grouping-

This list controls how the dialog organizes the list of available aircraft. By default, the
aircraft are sorted by Product. Here is an explanation of the different sorting methods:
Product, Airframe: Aircraft are grouped first by which product they are found in (all
custom aircraft will be in the Custom Aircraft folder). Within each product, the
aircraft are further grouped by airframe. For example, NextSTAR and NextSTAR
with AFS are both found in the NexSTAR airframe folder.
Product: Aircraft are grouped by product alone.
Airframe: Aircraft are grouped by airframe, not by product. Individual aircraft are
grouped inside each airframe folder.
None: There is no grouping at all. All aircraft are sorted alphabetically.

112

Color Scheme-

If applicable, this list contains the alternative trim schemes for the selected model. If
the Color Scheme dialog is grayed out, there are no alternative trim schemes available
for this particular aircraft.
If the list control is active, click on the down arrow to reveal the alternate trim
scheme(s). To select an alternate trim scheme, use either the up/down arrow keys on
the keyboard or select one with the mouse. When an alternative trim scheme is
selected, this scheme will appear immediately in the ReadySelect preview box, replacing
the previous trim scheme.
Additionally, modelers may create their own trim schemes in RealFlight using a thirdparty bitmap editor capable of manipulating Targa (*.tga) files. Please see the section
titled Save Color Scheme As..

Edit Current Aircraft

RealFlight G4 offers the user unparalleled freedom to edit or modify their aircraft. Its
possible to add and remove components, alter their location, change airfoils and much,
much more! The first several times that you access the aircraft editor, the task might
seem daunting. It may require some getting used to before you are comfortable with
this feature and its related functions. The best way to do so is to simply dive in and
experiment.
To modify the currently selected aircraft, click the Aircraft menu followed by the Edit
Current Aircraft menu item. This brings up the Aircraft Editor dialog, which will
allow you to modify any of the hundreds of parameters for the currently selected
aircraft.

113

The Aircraft Editor dialog will have an appearance similar to the screen shot shown
below. It may deviate slightly depending upon the type of aircraft that you are editing
(i.e., biplane, electric model, etc.). However, all aircraft are edited in a similar manner.
As such, this section presents you with the general information necessary to edit any
aircraft found in G4.
Aircraft Editor Menus-

Selecting the Edit Current Aircraft option activates the screen shown above. The
Aircraft Editor dialog has four menu options:

File

Edit

Options

View
File Menu-

This menu and its menu items are used to manipulate and control the various
folders and related items in the aircraft editor.

114

Open-

This menu item is used to open existing and edited aircraft. Selecting
this menu item opens the Select Aircraft dialog. To select an aircraft
from this list, follow the procedure described in the Aircraft Selection
section of this manual.
Save-

This option becomes active once you have renamed and saved the
edited aircraft. Prior to doing so this option will remain inactive or
grayed out. This allows you to make further modifications to the
aircraft without renaming it each time.
Save As-

Upon completion of the aircraft editing, click this menu item to

rename and save the modifications. You will be asked to create a
name for this new aircraft. After you have renamed the aircraft, click
OK to accept the new name. Afterwards, the aircraft will appear in
the aircraft listings found in the Select Aircraft in the Aircraft menu.

115

Revert-

This menu item allows you to revert, or go back to the settings the last
time that the aircraft was saved. If you have not previously saved the
aircraft, the aircraft will return to the default settings.
To use this menu item, open the File menu and click Revert. This
will bring forth the verification dialog.
Click Yes if you wish to return to the last saved version of this model.
Please note: any modifications performed after the last time that this
model was saved will be lost. Clicking No will allow you to save the
modifications or continue refining the aircraft.
Exit to Simulator-

This menu item returns you to the simulation. If you have performed
any modifications to the aircraft and have not saved these
modifications, a verification dialog will appear. Choose Yes to save
the modifications. If you select No, the modifications will be lost.
Selecting Cancel will return you to the editing dialog.
Edit Menu-

As is suggested by the name, this menu is utilized to edit the aircraft. The
available options depend upon which item or folder is highlighted in the
directory. If you have not highlighted an item or folder, the Edit menu will
remain grayed out or inactive.

116

For example, if the aircraft name is highlighted and the Edit menu is selected,
there will not be any actions available to you. If the airframe is highlighted, the
aircraft editor will allow you to add various components to the airframe.
Alternatively, if you wish to either add or remove an item from one of the
aircraft components, right-click on the respective component. This will bring
forth the available options.
When editing aircraft, you can click and drag the mouse in the preview area to
rotate the aircraft to different angles. This helps to better see components you
might be modifying.
Options Menu-

This menu provides you with a number of choices, or options, available to you
for use in the aircraft editor.
Selecting the Options menu brings forth the drop-down menu items discussed
below.

117

Play Engine Sounds-

Selecting this menu item plays the respective engine sounds during the
editing of this aircraft. Please note: this setting is only temporary.
That is, this setting is not retained after you exit the aircraft editor.
To select this option, click the Play Engine Sounds menu item. This
will place a check mark before the setting and return to the aircraft
editor. Additionally, the engine sounds will become audible.
Additionally, you may also press the P key on the keyboard to enable
or disable the engine sounds.
Display Advanced Properties-

This option displays advanced properties for the components in the

airframe. Using the advanced properties you may fine-tune the physics
calculations performed by RealFlight, in order to adjust the flight
performance to your liking. When this option is checked, additional
component properties will be displayed in the property listing area of
the aircraft editor dialog. These properties are marked as Advanced
in the following sections.

118

Additionally, you may also press the D key on the keyboard to display
or eliminate the advanced properties from the dialog.
Units-

This option toggles the units of measure between metric and SAE
units. It is important to note that modifying this option affects all
measurements in the simulation. For example, changing from SAE to
metric in the editor also affects the airport editor dialogs.
To modify this option, click the Display Metric Units setting. Then
select the unit of measurements you would prefer from the drop down
menu. The options are English or Metric. A check mark will appear
next to the unit that is currently displayed.
Alternatively, you can press the U key on the keyboard to switch
between the different units of measurement.
Reload Color Scheme-

This option allows you to view the results of an edited trim scheme.
There are two ways that you can do so. The first is to use the Select
Color Scheme menu, which is found within the Aircraft menu.
Simply click on the color scheme that you have just edited, and
RealFlight will reload the color scheme onto your aircraft and reset the
aircraft back on the runway.
Alternatively, within the aircraft editor, click on the Options menu
item. Select Reload Color Scheme. Clicking this reloads the color
scheme, showing any changes you have made to the aircraft. To
improve visibility of the trim scheme, you may wish to remove the
wireframe from the preview. To do so, please follow the procedure
noted in the description for Show Wireframe.
You can also press the R key on the keyboard to reload the color
scheme.
View Menu-

The View menu in the aircraft editor offers choices on the perspectives of the
aircraft in the preview window.

119

Look At-

This option allows you to determine the view of the aircraft being
edited. There are three options available from this menu.

Aircraft Center- Check this option is you wish to keep the entire
aircraft centered in the view.

Component Center- Check this option to center the view around

the component you are editing. For example, if you are modifying
the rudder, the aircraft will shift so that the rudder appears in the
center of the preview area.

Component Origin- Checking this option will focus the view on

the root, or origin, of the component you are currently modifying.
For example, if you have the Main Gear selected, the preview area
will be centered at the location where the Main Gear is attached to
the fuselage.

To adjust the Look At perspective, click the Look At menu item and
select the desired view. Alternatively, you may use the A key on the
keyboard to toggle through the selections.

120

Look From-

Alternatively, you can select from pre-determine angles from the Look
From menu item. They include:

Above Look from above the aircraft. Or press the Q key to

quickly change to this view.

Below Look from below the aircraft. Or press the Shift-Q keys
to quickly change to this view.

Right Look from the right side of the aircraft. Or press the W
key to quickly change to this view.

Left Look from the left side of the aircraft. Or press the Shift-W
keys to quickly change to this view.

Front Look from the front of the aircraft. Or press the E key to
quickly change to this view.

Back Look at the back of the aircraft. Or press the Shift-E keys
to quickly change to this view.

Show Wireframe-

This option determines whether the aircraft displayed in the preview

box is shown as a wireframe or is rendered complete with textures, etc.
The wireframe option is automatically selected by default.
If you would prefer to view the fully rendered image, click the Show
Wireframe option from the pull-down list. This will eliminate the
check mark from the setting and return to the aircraft editor.
Additionally, the preview aircraft window will show the rendered
image of the aircraft.
Alternatively, you may press the S key on the keyboard to display or
eliminate the wireframe view.
Aircraft Parts Tree-

The bottom half of the Aircraft Editor contains three important areas; the Aircraft
Parts Tree, Parameter window, and the description pane.

121

The Aircraft Parts Tree breaks down the entire list of aircraft components and radio
data into an easy-to-use hierarchy.
The first item listed is the name of the aircraft you are currently editing, and is
considered the root item for all other items listed here. Selecting it will offer a variety
of common parameters that you can edit in the Parameter window. These include the
description of the aircraft, Launch Method, Power Plant Type and Radio Type.
Below the aircraft name, there are additional options that allow you to customize the
individual parts of the aircraft. You also have the ability to modify the electronics and
radio program for the aircraft.
Each part belongs to a higher component, or parent, with the root being the highest
component. In return, its possible that the part itself also has children parts that
belong to it. For example, if you wish to edit the wheel size on the P-51, you will find
it under the following path in the Aircraft Parts Tree:

122

P-51 Mustang - root of the aircraft, found at the top of the Aircraft Parts Tree list
o Airframe Contains all the physical parts of the aircraft, like wings,
fuselage, etc.
Main Wing One of many physical parts found in the Airframe

Main Gear The Main Gear on the P-51 attaches to the

wing, therefore, we found it under the Main Wing part.
o Main Wheel Finally, youll see the wheel
component which, understandably, is found
under the Main Gear part.

Once the Main Wheel is selected, the Parameter window will change to show all
parameters available to the Main Wheel. Youll notice that one of these parameters is
wheel diameter.
All other parts are found and modified in much the same way. If, however, you are
unsure as to the location of a part, an easier way to access the part is to click on the
desired item in the Preview screen on the top half of the window. For example, if you
want to modify the parameters for the horizontal tail of the P-51, simply click on that

123

portion of the image. Youll notice that the Horizontal Tail is now selected in the
Aircraft Parts Tree.
Preview Screen-

As mentioned above, to quickly find the part in the Aircraft Parts Tree for
modification, you can simply click that part in the Preview screen itself. At times, youll
notice that the part you want to click might be hidden behind another section of the
aircraft. If you find yourself in this situation, click and drag the mouse cursor around
the Preview screen. This will rotate the aircraft image around so you may view it from
different angles. You may also use the scroll wheel on the mouse to zoom in and out
for a closer look at the section you are working on.
Parameter Window-

On the bottom half of the Aircraft Editor, you will see the Parameter window on the
right side. This window will list all the parameters available for the currently selected
part in the Aircraft Parts Tree.

Clicking on the parameter will allow you to view a description of its use in the
Description pane directly below the Parameter window. This will also allow you to
modify the currently selected parameter.

124

Add and Removing Components-

There are times when you may want to add a new component to the aircraft. The first
step is to determine the location for the new part. For example, if you were to add
flaps, it makes more sense to add it to the main wing, than to the fuselage.
After having determined the location for the new part, you can add it in one of two
ways. Select the new part from the Edit menu. Alternatively, you can right-click on
the component in which you are adding the new part. Again, if you were adding flaps,
right-click on the Main Wing component, then select Add Control Surface.
Removing a component works in much the same way. In the Aircraft Parts Tree,
select the component you wish to remove. Then select Delete Component from the
Edit menu. Alternatively, you can accomplish the same thing by right-clicking on the
part to remove and selecting Delete Component.
More Information-

The Aircraft Editor may seem a little overwhelming at first. The best way to become
familiar with the editor and its related functions is to simply use it and start
experimenting. RealFlight does not allow you to customize the stock aircraft. As such,
if you make a change to one of the stock aircraft, you will be forced to save it under a
new name. Therefore, you always have the stock aircraft to default to, should the need
arise.
Our online forums and swap pages provide a great source of information, and
assistance from other RealFlight users. These pages may be found at:
http://www.knifeedge.com/forums/

Select Color Scheme

This menu item allows you to choose an alternative trim scheme (if available) for the
current aircraft.

125

To view the alternative color schemes, click the Select Color Scheme menu item. To
select an alternate trim scheme, click the existing selection in the value box. This will
bring forth the pull-down menu selections. Use either the Up/down arrow keys on
the keyboard, or the mouse to select the desired option. If utilizing the arrow keys,
press Enter to finalize the selection. The new trim scheme will appear immediately on
the aircraft. Please note: if only one scheme appears in the pull-down menu,
alternative schemes are not available for this aircraft.

Save Color Scheme As

This menu item is used to create an editable version of the currently selected trim
scheme.

126

RealFlight G4 allows you to create a custom paint/decal scheme for your aircraft. The
color schemes you create are limited only by your imagination.
However, only individuals that own, and know how to use, a third-party bitmap editing
program such as Adobe Photoshop, should attempt to create a custom color
scheme. Your editor must be able to read and edit Targa (.tga) files.
To create a custom color scheme click the Save Color Scheme As menu item.
Enter the desired name in the dialog box that appears. The location of the file will
appear in the lower left corner of the RealFlight screen.
To access the file that contains the custom color scheme, open the My Documents
folder. Next, open the RealFlight G4 folder followed by the Vehicles folder. A
number of folders are available here, open the folder called ColorSchemes. This will
bring up all of the custom color schemes that have been stored in RealFlight. The
name of the aircraft will precede the name that you have selected for your custom
color scheme. Click on the file for which you wish to modify the trim scheme.

DO NOT ALTER THE NAME OF THIS FILE, AS REALFLIGHT MAY

NOT BE ABLE TO CORRELATE THE COLOR SCHEME WITH THE
AIRCRAFT.

127

Once you have finished editing and saving your color scheme, you will probably want
to see the results of your work. There are two ways that you can do so. One is to use
the Select Color Scheme menu, which is found within the Aircraft menu. Simply click
on the color scheme that you have just edited, and RealFlight will reload the color
scheme onto your aircraft and reset the aircraft. Within seconds, you are ready for
flight with your new color scheme.
Alternatively, access the Aircraft Editor (see section Edit Current Aircraft on page 113).
Within the aircraft editor, look for Reload Color Scheme which is located in the
Options menu. Clicking this will reload the color scheme, showing any changes you
have made to the aircraft. You can disable the wireframe using the Options menu to
improve your view.
While looking in the ColorSchemes directory for your new color scheme, you may also
notice a .colorscheme file with the same name as the .tga file. This file can be
opened in a text editor such as Notepad. Within the file, you will find six values to edit:
Specular, Reflectivity, PowerSpecularOff, PowerSpecularOn, PowerReflectiveOff, and
PowerReflectiveOn.
Specular - A multiplier for the overall specularity of the aircraft. Specular=1 is neutral,
Specular=0 disables specular highlights.
Reflectivity - A multiplier for the overall reflectivity of the aircraft. Reflectivity=1 is
neutral, Reflectivity=0 disables reflections.
Specular highlights vary from fully off to fully on as the specular power of each piece
of the aircraft goes from the value PowerSpecularOff to PowerSpecularOn.
Reflections vary from fully off to fully on as the specular power of each piece of the
aircraft goes from the value PowerReflectiveOff to PowerReflectiveOn.
Tips for Color Schemes

A quick and easy way to change a color scheme is to replace one color
with another. Photoshop has a command that can easily do this called
Replace Color.

Make sure you save the file as 32 bit TGA files so that the Alpha Channels
are preserved (See below).

You are only allowed a single Alpha Channel.

Do NOT alter the resolution of the image.

Other formats (JPG, BMP, etc) are not allowed.

128

Alpha Channels

Almost all of the color schemes for the aircrafts incorporate an Alpha Channel, which
defines what areas of the color scheme are opaque and what areas are transparent.
White portions of the alpha channel will be 100% opaque and Black portions of the
alpha channel will be 100% transparent. Shades in-between will be partially
transparent.
Consult the image editors manual to determine how to use Alpha Channels.
Note: RealFlight uses TGA files instead of the BMP format. This is because BMP formats do not
support alpha channels.

Remember Aircraft Position

The Remember Aircraft Position menu item saves the current position of the aircraft.
When you reset the aircraft, it will return to the same position (speed, attitude, heading,
etc.) as when this menu item was selected. This feature is ideal for practicing
maneuvers, such as an autorotation in a helicopter.

129

To activate this menu item, click the Remember Aircraft Position menu item when
the aircraft is in the desired location and altitude. Alternatively, pressing the P key on
the keyboard will also remember the aircrafts position.
Each time the aircraft is reset it will begin flight from the saved location. Please note:
the saved position is only temporary. If you select another airport, aircraft, or if you
exit the simulation and restart, you will need to save the desired position once again.

Clear Aircraft Position

This menu item clears the position saved in the Remember Aircraft Position without
exiting the simulation, changing flying sites and/or aircraft.

To do so, simply click the Clear Aircraft Position menu item. When the aircraft is
reset, it will return to one of the default starting positions.

130

Reset Position
There are three ways to reset the aircraft to its takeoff position:
1. Press the Reset button on the InterLink Elite controller. This is probably the
fastest and simplest method.
2. Press the keyboards space bar.
3. Click the Reset Position menu item.

131

Kill Engine
Click on this item to instantly stop the motor from running. This is useful when you
are practicing dead-stick landings in airplanes and when practicing autorotations for
helicopters. Alternatively, you may also press the keyboards K key.

132

Aircraft MRU
The final items in the Aircraft menu indicate the most recently used aircraft. The first
item is the aircraft that you are currently flying; successive items are aircraft you have
previously flown. The MRU shows only the eight most recently selected aircraft.

You can load an aircraft by selecting it from this list. This shortcut allows you to
switch between your favorite aircraft without using the Select Aircraft dialog.

133

Chapter

Controller Menu
Determine the method of control, map the channels to your liking, and calibrate
the controller.

he Controller menu allows you to select the method of control, calibrate the
controller and to map the channels for your desired method of control for
RealFlight G4.

When you click the Controller menu, a screen similar to that below will appear:

The menu items available are:

135

Select Controller

Controller Calibration

Channel Mapping

Select Controller
When you click on the Select Controller menu item, the following sub-menu appears:

To choose the method of control, click on the Select Controller menu item from the
Controller menu. The selection(s) will vary depending on whether or not you have
attached an actual R/C transmitter to the interface adapter for the InterLink Elite.
Please note: if you have attached a controller to the InterLink Elites interface port,
RealFlight will pause briefly while it detects the transmitter.
The selections are (usually) InterLink Elite and InterLink Elite Transmitter X Channel.
If you will be using your own controller in the simulation, choose the InterLink Elite
Transmitter X Channel. The sections that follow will explain the differences

136

between the various modes and methods of control and the means and ways to access
and utilize them.
If you have attached a Generation 2 InterLink controller or a G3 InterLink Plus
controller in addition to the G4 InterLink Elite, there will be an option allowing you to
select these controllers as well.

Controller Calibration
The Controller Calibration menu item allows you to adjust your controller for use
in the simulation. Calibration is the method of fine-tuning the controller input for the
simulation, so that you will achieve the desired responses.

Once selected, the following screen appears:

137

As directed, place all sticks, knobs and switches to their center positions. Click Next
when finished.

138

It is imperative to move all of the sticks, knobs and switches through their complete
range of motion several times. This is the key to a properly calibrated controller.
When completed, click Finish. You will now be returned to the simulation with a
calibrated controller.

Channel Mapping
G4s Channel Mapping feature allows for incredible flexibility and adjustability
regardless of radio manufacturer or flight mode utilized. This menu item enables you
to define the functionality of the transmitter when utilized in the simulation.

To access the Channel Mapping menu item, click the Controller menu. Next, select
the Channel Mapping option. This will bring forth the following screen.

139

It is important to have a basic understanding of the Channel Mapping screen prior

to actually modifying the actual mapping itself.
Channel-

This column corresponds to the actual channel of the transmitter used to control the
functionality, as defined in the Map To column.
For example, radio channel 3 on a Futaba radio corresponds to the throttle. As such,
the Map To value is defined as throttle. On the other hand, radio channel 3 on a JR
radio controls the pitch (elevator).
The first column displayed shows the number for the input channel. You can change
this by clicking the down arrow next to the number and selecting a different channel.
This is useful if you want the same channel to control multiple functions. For example,
with this option you could assign channel 3 to control both throttle and elevator. Its

140

important to note that this will affect all aircraft. See Edit Current Aircraft on page 113
for information on how to edit the individual aircraft.
The radio channel values serve as placeholders, or reminders, for the functionality of
your transmitter with regards to the Map To functions.
Map To-

The values here define the function or duties that will be performed by the transmitter.
Using the example from the Radio Channel above, the Map To for Futabas Channel 3
dictates that this will control the throttle of the desired aircraft. For JR radios, Channel
3 on the transmitter controls the pitch (elevator).
If your transmitter varies from the default definitions, it is necessary to modify the Map
To functions. To do so, click on the Map To channel that corresponds to the channel
you wish to adjust. Using either the up/down arrow keys on the keyboard or the
mouse, select the desired Map To channel. If using the up/down keys, press Enter to
finalize your selection.
If the channels are mapped, or defined properly but control input produces results that
are backwards (e.g., increasing the throttle stick actually decreases the throttle on the
aircraft), please refer to the Reverse Channel section that follows.
Reverse Channel-

The value here determines whether to reverse the input received from the radio
channel. If checked, the input will be reversed.
To adjust the input direction, click on the corresponding Reverse Channel checkbox
as necessary.
Using RealFlights Channel Mapping-

Now that you have a basic understanding of the Channel Mapping, it is time to utilize
this knowledge to program the software for your controller.
While watching the channel values, move the gimbal stick that controls the throttle
input for your aircraft. Taking note of the value, map this channel to the throttle.
Repeat this procedure for ALL corresponding channels on the transmitter. When you
have finished, click OK. Next, return to the simulation and test the Channel Mapping
to ensure that all channels are mapped correctly and that all function as desired. If not,
please return to the Channel Mappingmenu item and refine accordingly.
After you have correctly mapped the channels, it is best to re-calibrate your transmitter.
To do so, please see the Controller Calibration section on page 137.

141

Joystick Mode vs. Transmitter Mode

In single-player mode, RealFlight allows you to quickly and easily change the method
used to control the action in the simulation. RealFlight G4 offers two control modes:

Joystick Mode. Using the InterLink Elite in Joystick Mode, RealFlight G4 accepts
control input from the sticks, switches, knob and push-button on the InterLink
Elite controller. This is the default mode when you install RealFlight. Again, we
suggest that you fine-tune the calibration of the controller. For information on
how to do so, please refer to the Controller Calibration section on page 137.

Transmitter Mode. Using the InterLink Elite in the Transmitter Mode, RealFlight
G4 accepts commands from your actual R/C transmitter. To use this mode, your
transmitter must be connected to the InterLink Elite controller via the InterLinks
built-in interface. This is an optional use of the InterLink, and we have provided
the necessary cables for using most popular R/C transmitters. Using the
Transmitter Mode takes slightly more setup and understanding of your radio than
does using the Joystick Mode.

To switch between these modes, highlight the Select Controller menu item. The
InterLink Elite controller will automatically test to determine whether an R/C
transmitter is present. After the detection testing completes, select the mode that
you wish to utilize for your flight -- either Transmitter Mode or Joystick Mode.
Regardless of which mode you select, you will return to the simulation and be
ready to start flying immediately.

InterLink Elite Controller (Joystick Mode)

In Joystick Mode, RealFlight accepts control input from the sticks, switches, rotary
knob and push-button found on the InterLink Elite controller. This is the default
mode when you install RealFlight G4.
The RealFlight G4 software, working in conjunction with the InterLink Elite
controller, actually does all the radio processing to measure the raw stick, switch, knob
and push-button input from the controller. It then processes this input to produce the
servo outputs that are used to control the aircraft.
Helicopters, for example, ordinarily require a great deal of mixing to achieve flight.
This mixing is normally the function of a computer radio. When RealFlight G4 uses
the Joystick Mode, the mixing is done by the RealFlight G4 software itself and not by
the InterLink Elite controller.

142

Channel Modification-

It is possible to modify the mixing of the radio in the Software Radio menu. To access
the Software Radio menu, click the Aircraft menu followed by the Edit Current
Aircraft menu item. Next, click on the Software Radio menu.
Every aircraft in RealFlight has its own unique software radio program that maps
(converts) the raw stick inputs from the InterLink Elite controller into the correct
servo input for that particular aircraft.
Controller Calibration-

Occasionally it may become necessary to fine-tune your InterLink Elite controllers

calibration. To do so, click on the Controller menu followed by the Controller
Calibration menu item. Follow the directions that appear on-screen to complete
the calibration procedure.
Stick Mapping

As noted above, RealFlights Channel Mapping feature allows you the flexibility to
modify the operational mode of the transmitter. Typical operation modes are as
follows:

Transmitter Mode 1 (Europe, Asia) - Mode 1 transmitters have aileron and throttle
on the right stick, and rudder and elevator on the left stick.

Transmitter Mode 2 (USA) - Mode 2 transmitters have aileron and elevator on the
right stick; rudder and throttle on the left stick.

Transmitter Mode 3 - Mode 3 transmitters have rudder and elevator on the right
stick; aileron and throttle on the left stick.

Transmitter Mode 4 - Mode 4 transmitters have rudder and throttle on the right
stick, and aileron and elevator on the left stick.

InterLink Elite Controller (Transmitter Mode)

This exciting feature allows you to plug your own R/C transmitter into the back of the
InterLink Elite controller. You can then use your own transmitter to control the
RealFlight aircraft. With Universal Serial Bus (USB) connectivity, the InterLink Elite
controller offers high resolution, rapid data transfer from your transmitter to the PC,
and immediate response from the simulated aircraft.
When compared to the Joystick Mode, using your own radio adds a slight amount of
complexity and initial configuration setup. The advantage to this method is that it will
allow you to become familiar with the programming on your actual R/C transmitter.
Additionally, you will develop the feel of using your transmitter rather than the
InterLink Elite controller.

143

Two ways to use the InterLink Elite Transmitter Mode-

There are two ways to use Transmitter Mode. They are commonly referred to as the
Pass Through Interface and Joystick Emulation Interface (not to be confused with
the Joystick Mode in the previous section). Here is a quick chart that will help you
decide which mode to use.
InterLink
Elite
Joystick
Mode

InterLink Elite
Transmitter
Mode: Joystick
Emulation
Interface

InterLink Elite
Transmitter
Mode: Pass
Through Interface

Radio used to Fly InterLink

Elite
Controller

Your own R/C

radio

Your own R/C

radio

Ease of
Configuration

Very Easy

Medium. Must
calibrate and
setup radio one
time.

Harder. Must
separately calibrate
and set up radio for
each aircraft.

Fly Stock aircraft

without
Modification

Yes

Yes

No

Gives you the

feel of your own
radio

No

Yes

Yes

Puts wear and

tear on your
own transmitter

No

Yes

Yes

Allows you to
perform mixing
in your own
radio

No

No

Yes

144

R/C transmitter
required

No

Required: 4-8
channels.
Computer radio
not required

Required: computer
radio with multiple
model memory.
Recommended:
radio with 7-12
channels.

Transmitter Mode: Joystick Emulation Interface

The purpose of the Joystick Emulation Interface is to create a program on your own
R/C transmitter to provide RealFlight with raw stick inputs. This enables RealFlight to
use its own software radio to control all of the stock aircraft.
It also allows you to use a single model memory, or program, on your R/C transmitter
to control, without modification, all of the stock aircraft in RealFlight. We suggest that
you perform the Channel Mapping and Controller Calibration procedures in this order,
respectively. This will prevent you from having to re-calibrate your controller if one (or
more) of the channels is not mapped correctly.
Channel Mapping

Before accessing the Channel Mapping menu item, you will need to create a new
program or model memory on your R/C transmitter. We suggest that you call it
RFJOY or something similar.
Please make sure that this new program meets the following criteria:

Is an airplane program--you do not want a heli program with all of its mixing (since
all the mixing will be performed by the RealFlight software)

Does not have any mixing programmed

Has trims centered

Has ATVs set to 100%

Has dual rates and expo turned off as these may be emulated in the RealFlight
software radio

Prior to starting this wizard, make sure that your transmitter is attached to the
InterLink Elite controller and that the controller is on. Click the Controller menu
followed by the Select Controller menu item. There will be a momentary pause while
RealFlight detects the R/C transmitter. Next, click InterLink Elite Transmitter X

145

Channel. After this is accomplished, click Channel Mapping Follow the onscreen instructions, making sure that you read all of the instructions in each step.
Once you have finished, it is best if you never modify the RealFlight radio program in
your transmitter again. A change in this RFJOY program will affect every RealFlight
aircraft flown with this transmitter. Instead, edit the Software Radio in RealFlight.
Changes to the Software Radio only affect the aircraft whose radio you have edited.
Controller Calibration

By calibrating the R/C transmitter for use with RealFlights software you are, in
essence, advising RealFlight as to the minimum, maximum and center values for each
channel on your particular radio.
To calibrate your transmitter, click the Controller menu followed by the Controller
Calibration menu item. Follow the on-screen instructions to complete the
calibration procedure.
You are now ready to fly any of the stock aircraft available in RealFlight.

Transmitter Mode: Pass Through Interface

This is the most advanced method for controlling the RealFlight aircraft. It provides
total control of an aircraft from your own radio and utilizes all of your radios mixing
functionality. All values received by RealFlight are passed directly to the aircraft
without modification from the RealFlight software. The disadvantage is that you will
have to create a new radio program (model memory) on your R/C transmitter for each
aircraft you want to fly with this mode. You must also set up your radio, mixes, trims,
dual rates, etc. on the transmitter for each aircraft you want to fly with this mode.
The advantage of this mode is that if you are mainly flying one or two aircraft on
RealFlight, you use your own radio program for these aircraft and have complete
control over them. It also is a very good tool for learning how to use your own R/C
radio as it forces you to set up the transmitter the same way you would have to set it up
if you were going to control an actual R/C aircraft.
Before you use the Pass Through Interface-

IMPORTANT! Make sure that you follow the procedures for both the Controller
Calibration AND the Channel Mapping menu item in the previous sections
BEFORE attempting to use the Pass Through Interface. Failure to do so may result in
an aircraft that either does not perform adequately or fails to perform at all.

146

Setting the Pass Through Interface-

After completing the Controller Calibration and the Channel Mapping

procedures, select the desired aircraft. Next, select the Edit Current Aircraft menu
item. Highlight the aircraft root (name of the aircraft) and select the value for the
Radio Type. Using either the mouse or the up/down arrow keys on the keyboard,
select the Pass Through option from the pull-down menu.
Mapping channels to Servos-

If any channels are mapped to the wrong functions on the aircraft, edit the aircraft
using the following procedure. Click the Edit Current Aircraft menu item. Access
the Electronics options. Double-click the Electronics name or click on the [+]
(plus). Select the incorrectly mapped channel from the pull-down list that activates.
To change the respective channel of operation, click on the corresponding value and
select the appropriate option from the pull-down list.
IMPORTANT! Do not change the servo mapping using the Channel Mapping
menu item. If you do so, the change will also affect ALL stock aircraft. Instead,
simply change the servo mapping using the Electronics options above for a single
aircraft.
Sharing Aircraft that use the Pass Through Interface-

In most cases, when you make a custom aircraft that uses the Pass Through Interface
option, you will not be able to provide that aircraft to your friends or submit it to the
RealFlight Model Swap Page. This is because the RealFlight software does not receive
the necessary input for the radio programming. Consequently, you would have to
provide other RealFlight users with all of your R/C radios settings for that particular
aircraft. Moreover, they would have to have the exact same R/C transmitter in order
for them to use the aircraft. These complications effectively prohibit swapping aircraft
under these conditions.

InterLink Elite Controller Tips

What if my transmitter has fewer channels than the model I select?

This issue can arise when you use your own transmitter to control RealFlight G4. In
this situation, we highly recommend that you use the InterLink Elite controller.
When to use the Channel Mapping, and when to use the Software Radio or Servo
page-

This issue arises only if you use your own transmitter to control RealFlight. When you
use the InterLink Elite controller as a mockup transmitter, you should not alter the
Channel Mapping.

147

Remember that Channel Mapping is used to set the input channels for your
transmitter. This means that you are setting the channels used to monitor physical
movements or positions of your transmitters sticks, switches, and knobs. Unless you
change transmitters, you should only need to set this once. Only use the Channel
Mapping menu item to tell RealFlight which channel your controller is using for each
stick/knob/switch input, not what control function you want that stick/knob/switch to perform.
The Software Radio controls mixing, exponential, and other channel processing that a
computer radio would normally perform. The Software Radio determines the control
function you want each stick/knob/switch setting to perform. You will most likely
want to adjust this differently for various aircraft. For example, the mixing utilized for
your glider will probably not be very useful on a jet.
The Electronics options modify the servo properties (e.g., servo speed) as well as
adjusting the input channels in the same way as the Channel Mapping wizard.
However, changes made using the Electronics options only apply to the particular
aircraft that you are editing. Use the Electronics options only when you want to edit a specific servo
property (like servo speed) or if for some reason you need to reassign an input channel for one aircraft
only. In most cases, you should not need to do the latter. Instead, you should normally
use the software radio to configure control outputs.
A good rule of thumb: if a setting will not be the same for every aircraft, you should not try to
implement the setting by using the Channel Mapping menu item. Instead, adjust the Software
Radio.

148

Chapter

Events Menu
Challenge your flying skills by competing in events, by yourself, or join others
online.

n event is an organized flying contest with a set of rules. RealFlight G4

supports five types of events: Autorotation/Deadstick, Free Style, Limbo,
Pylon Racing and Spot Landing. You can participate in these events by
yourself or compete with other RealFlight G4 users over the internet.

To participate in an event alone, all you have to do is start the event. RealFlight G4
does the rest.
If you want to compete with other RealFlight G4 users, you must first start a
multiplayer session (or join an existing one). See the Multiplayer chapter for additional
information on how to do so.
When all of the participants have joined the session, the session host will start the
event. This enrolls every member of the multiplayer session in the Event. If any
multiplayer session members want to leave the event, they can do so while remaining a
part of the multiplayer session.
RealFlight G4 limits you to running only one event at a time. This rule also applies to
multiplayer sessions.
The Events menu accesses all events, and event-related options. When you open the
menu, the items are:

149

Autorotation/Deadstick

Freestyle

Limbo

Pylon Racing

Spot Landing

Options

End Current Event

Forfeit Turn

Some of these items may be grayed out if they do not apply to the current situation.
For example, you cannot end the current event unless an event is already running.
Consequently, the End Current Event menu item will be grayed out.

150

Autorotation/Deadstick
The Autorotation/Deadstick event is similar to the Spot Landing event mentioned
below. This event requires that you make a landing with all power off.

The goal of this event is to land the airplane, or autorotate the helicopter, into the
marked zones. The various landing zones have different point values assigned to them.
The zones that are more difficult to target are awarded higher point values. If
participating in a multiplayer event, the player with the highest points total at the end
wins.
It is possible to enable the software to kill the players engine when their aircraft
passes a particular altitude.
Selecting Your Name for the Event-

If you have already entered a name in the Settings menu item, this name will be
utilized for single player and multiplayer events. If you have not entered a name, please
do so in the space provided when you select an event. Click OK when completed.
To select a different name for this event, click on the Simulation menu, followed by
the Settings menu item. Next, click the Multiplayer name. This brings up the

151

multiplayer options. Click the value found next to the Pilot Name item. Use the
keyboard to input the name you wish to utilize for the events.
Options-

The Options menu item adjusts the parameters and rules for each event. To access
the Options menu item, click the Events menu followed by the Options menu
item. Next, from the column on the left side, select the event that you wish to adjust.
The selections that appear will depend upon the event selected. This section examines
the selections available for the Autorotation/Deadstick Landing Options.

Zone Point Values- Zones A through E-

The landing zones are divided into five segments. In the default settings, each
segment has a different point value assigned to it based upon degree of
difficulty. Zone A is the smallest, most difficult target. Therefore, it offers the
highest point value. Zone B, which surrounds the center, offers the second
highest points, followed by Zone C, D and E.
To adjust the values of these points, click on the values in the column to the
right of the respective Zone Points. For example, to adjust the points for
Zone A, click on the corresponding Value in the column next to Zone A.
Enter the desired value directly from the keyboard or via the mouse wheel.
Turns Per Event-

This option determines the number of turns that each player is allotted per
event. When each player has taken the designated number of turns, the event

152

is over. The only exception is if the host activates the Crash Eliminates Player
setting. In this case, the event will end if all of the players crash before they
reach the turn limit.
To adjust the number of turns, click on the corresponding value. Enter the
desired value directly from the keyboard or via the mouse wheel.
Throttle cut altitude-

As mentioned previously, in an Autorotation/Deadstick event, the host can set

the rules so that the throttle is cut manually or automatically. This section
refers to the settings for a manual throttle cut. For information on automatic
throttle cuts, please see the Player Kills Engine section below.
To adjust the altitude at which the throttle is cut, click on the corresponding
value. Enter the desired altitude value directly from the keyboard or via the
mouse wheel.
Time to Complete Turn (sec)-

This is the amount of time allotted for each player to complete his or her turn.
Note: the countdown or timer is initiated at takeoff.
To adjust the amount of time to complete the Event, click on the
corresponding value. Enter the desired value directly from the keyboard or via
the mouse wheel.
Target Scale-

This option determines the size of the landing targets.

To modify the size of the landing area, enter a number in the corresponding
value column. Enter the desired value directly from the keyboard or via the
mouse wheel. The size of the targets will scale proportionally.
Crash Eliminates Player-

This option determines whether a crash eliminates a player from the

competition. If No, the player will be able to continue his/her turn regardless
of whether or not they have crashed. If Yes, the event is over for them as
soon as a crash occurs.
To set Crash Eliminates Player option, click the value in the corresponding
column. From the pull-down list, select either Yes or No.
Player Kills Engine-

This option determines whether you want to cut off the engine manually or
allow RealFlight G4 to do so for you. If enabled, the player must manually kill
the engine above the Throttle Cut Altitude. RealFlight will display the engine

153

cut notification for you on-screen. With automatic throttle cutting, RealFlight
G4 will automatically cut the throttle as soon as the aircraft crosses the
minimum altitude threshold. Again, RealFlight will display the engine cut
notification for you on-screen.
To set Player Kills Engine option, click the value in the corresponding column.
From the drop-down list, select either Yes (manual cut required) or No
(automatic cut at altitude).

Autorotation/Deadstick Instructions
You can run an autorotation competition in either a single player or multiplayer
environment.

The person who starts the event decides upon the applicable rules and parameters. For
example, you can set:

The time allotment for each players turn.

How many turns each player receives.

154

Whether a players engine is automatically or manually killed during a turn.

The altitude at which an engine must be killed.

The physical dimensions of the landing target.

Whether or not a crash automatically disqualifies a player.

Point values of the different zones within the landing target.

RealFlight G4 automatically applies the rules you choose, and keeps track of scores.
During the event, the announcers voice will guide you through each phase of the
competition.
Rules

The Autorotation/Deadstick course consists of a target:

The object of the Autorotation/Deadstick event is to fly your model over the target,
kill the engine, then touch down as close as possible to the center of the target. Players
take turns making landing attempts. When your turn comes, you will normally takeoff,
gain altitude until you are above the minimum Throttle Cut Altitude, fly towards the
target, and then kill your engine and autorotate or glide to the ground.
If the host so decides, you must kill your engine before dropping below the minimum
altitude to kill engine. Alternatively, the host can decide that your engine will
automatically shut off when you pass below this altitude. The host must also decide on
the minimum Throttle Cut Altitude.
A touch down occurs when any part of your airplane or helicopter touches ground.
Each touch down is marked with an X on the spot at which the aircraft landed.
Please note: this is not necessarily the point at which the aircraft stopped moving.
An attempt means you have passed below the minimum altitude to kill your engine.
Once your engine is disabled, you cannot reactivate it until your turn expires.
Additionally, you must land successfully (without crashing) to receive any points for
your attempt.
Furthermore, you must complete your landing before your turn time expires. If you do
not touch down in time, you will lose your turn.
The points you receive during a turn are dependent upon where you touch down.
Within the target, each colored zone has a different point value. Normally, the closer
to the center you land, the more points you will receive. Your touch down point is the
point on the ground directly below the center of your aircraft, no matter what part of
your aircraft touches first.

155

The event continues until the players complete all of their turns, all of the players are
disqualified (usually by crashing), or everyone has left the event. The player with the
highest point total at the end of the event is the winner.
Events Viewport Display Box-

During the event, a situational screen will appear on your display. This screen serves
several purposes: it indicates the players name, tracks the amount of time remaining to
complete the event, and indicates the remaining altitude before the engine is cut.
If you do not wish to view this information, double-click on the title bar of the display
box. This will hide the information. To view it once again, simply double-click the
title bar again.
To reveal the statistics for the event, click the arrow button in the upper right corner of
the box. Click the arrow button one more time to hide this information.
To resize the viewport, position the cursor over the lower right corner of the
viewports frame. Using the mouse, drag the frame according to your wishes. If you
drag it downward, the vertical size of the viewport will increase. Dragging the frame to
the right or left will increase/decrease the width of the viewport respectively.
Clicking on the X in the title tab of the viewport will close the viewport.

Freestyle
RealFlight G4s Freestyle event lets you make the rules. When you start a Freestyle
event, RealFlight G4 will allot every player a set of turns. Each players turn ends when
that players time expires (or if the player crashes). When this occurs, the next players
turn begins. What players do during their respective turns is completely up to the
participants. Weve included some possible freestyle examples below.

156

Whatever activity you pick, RealFlight will see that each player receives a timed turn.
You can use freestyle with any aircraft (airplanes or helis).
Selecting Your Name For the Event

If you have already entered a name in the Settings menu item, this name will be
utilized for single player and multiplayer events. If you have not entered a name, please
do so in the space provided when you select an event. Click OK when completed.
To select a different name for this event, click on the Simulation menu, followed by
the Settings menu item. Next, click the Multiplayer name. This will bring up the
multiplayer options. Click the value found next to the Pilot Name item. Use the
keyboard to input the name you wish to utilize for the events.
Options

As the name suggests, the Options menu item is used to adjust the parameters and
rules for each of the events. The Autorotation/Deadstick Event section discusses general
notes for this option. This section examines the selections available for the Freestyle
options.

157

Time to Complete Turn (sec)-

This is the amount of time allotted for players to complete their turn.
Please note: the time begins at takeoff.
To adjust the amount of time to complete the event, click on the
corresponding value. Enter the desired value directly from the keyboard or via
the mouse wheel.
Turns Per Event-

This option determines the number of turns that will be allotted to a player for
the event. The event is over when each player has taken this number of turns,
or sooner if the host activates the Crash Eliminates Player option and a crash
occurs.
To adjust the number of turns, click on the corresponding value. Enter the
desired value directly from the keyboard or via the mouse wheel.
Crash Eliminates Player-

This option determines whether a crash eliminates a player from the

competition. If No, the player will be able to continue his/her turn regardless
of whether or not theyve crashed. If Yes, the event is over for them as soon
as they crash.

158

To determine whether a crash eliminates a player, click the value in the

corresponding column. From the pull-down list, select either Yes or No.

Freestyle Instructions
You will usually want to use Freestyle in a multiplayer environment, but it works in
single player mode as well.

Before you start this event, you will ordinarily decide what the participants must do.
You may just want to use the event to give everyone an equal chance to showcase his
or her aerobatic skills. This will prevent you from worrying about your scoring. If you
want to have a competition, we suggest that before you begin the event:

Everyone should agree on the rules.

The host may need to edit the airport to add any equipment (pylons, runways,
fences, obstacle rings, limbo poles, etc.) that you will need for the event.

Everyone should agree how the event will be judged. You could appoint one
player to decide on a score for every other player, or have everyone in your session
vote on the best maneuver, etc.

159

The person who starts the Event (multiplayer session host) can pick:

How much time each player is allotted per turn

How many turns each player receives, and

Whether a player who crashes is automatically disqualified

We emphasize, the only limit on the freestyle event is your imagination. A few examples of what
you might wish to do:

Touch and Go. Appoint one partner to count runway touches, the contestant with
the most touches in a turn wins.

Aerobatics. Players use their turns to perform any stunt they want. At the end,
everyone votes on the best stunt.

Obstacle course. Set up a long obstacle (table, etc.) close to the ground and take
turns flying under it; land or takeoff from ramps, circle around pylons, etc.

It does not have to be a contest. You might all just want to take an equal turn at using
the runway (takeoff, land on alternate turns).
Events Viewport Display Box-

During the event, a situational screen will appear on your display. General notes on
this display were discussed in the Autorotation/Deadstick event section.

Limbo
A limbo event is a contest of piloting skill and courage. Players attempt to maneuver
their aircraft under a horizontal bar suspended across two vertical bars. After each
successive pass, the bar is lowered. The event continues until only one pilot remains.

160

Selecting Your Name For the Event-

If you have already entered a name in the Settings menu item, this name will be
utilized for single player and multiplayer events. If you have not entered a name, please
do so in the space provided when you select an event. Click OK when completed.
To select a different name for this event, click on the Simulation menu, followed by
the Settings menu item. Next, click the Multiplayer name. This will bring up the
multiplayer options. Click the value found next to the Pilot Name item. Use the
keyboard to input the name you wish to utilize for the events.
Options-

The Options menu item is used to adjust the parameters and rules for each of the
Events. See the Autorotation/Deadstick section for general notes about this screen. This
section examines the specific selections available for the Limbo options.

161

Minimum Bar Height-

This setting determines the lowest height that the bar will reach during the
Event.
To adjust the Minimum Bar Height, click on the corresponding value. Enter
the desired value directly from the keyboard or via the mouse wheel.
Maximum Bar Height-

This setting determines the highest setting (starting value) that the bar will
reach during the event.
To adjust the Maximum Bar Height, click on the corresponding value. Enter
the desired value directly from the keyboard or via the mouse wheel.
Distance to Drop Bar each Round-

After a participant successfully passes under the limbo bar, on their next
attempt the bar will lower by the amount indicated in this setting.
To adjust the distance by which the bar will be lowered each round, click on
the corresponding value. Enter the desired value directly from the keyboard or
via the mouse wheel.
Commit Line Distance-

This indicates the distance between the commitment lines and the limbo bar.
There is a commitment line on either side of the limbo bar and participants

162

may approach from either side. These lines detect an attempted pass at the
limbo bar.
To adjust the distance, click on the corresponding value. Enter the desired
value directly from the keyboard or via the mouse wheel.
Distance Between Poles-

The value entered here indicates the distance between the two vertical poles
that support the limbo bar. The wider the space between the poles, the easier
it is to pass through the gate, so to speak.
To adjust the distance, click on the corresponding value. Enter the desired
value directly from the keyboard or via the mouse wheel.
Time to Complete Turn (sec)-

This is the amount of time allotted for each player to complete his or her turn.
Please note: the countdown or timer is initiated at takeoff.
To adjust the amount of time to complete the Event, click on the
corresponding value. Enter the desired value directly from the keyboard or via
the mouse wheel.
Attempts Per Turn-

This value indicates the number of attempts that each pilot is allotted at any
given height of the limbo bar before being eliminated for that turn.
To adjust the number of attempts, click on the corresponding value. Enter the
desired value directly from the keyboard or via the mouse wheel.
Turns Per Event-

This option determines the number of turns per player for this event. When
this number is reached, the event is over. If the host activates the Crash
Eliminates Player option, however, the event may end sooner.
To adjust the number of turns, click on the corresponding value. Enter the
desired value directly from the keyboard or via the mouse wheel.
Crash Eliminates Player-

This option is used to determine whether a crash eliminates the player from
the competition. If No, the player will be able to continue his/her turn
regardless of whether or not they have crashed. If Yes, the event is over for
them as soon as a crash occurs.
To determine whether or not a crash eliminates a player, click the value in the
corresponding column. From the drop-down list, select either Yes or No.

163

Limbo Instructions
A limbo competition can be run in either a single player or multiplayer environment.
The limbo course consists of a limbo pole, and two attempt lines (also called
commitment lines), one on each side of the limbo pole.

The object of limbo is to fly an aircraft past the attempt line, then under the limbo bar,
in the time allowed. Players take turns attempting to fly under the bar. When your
turn comes, you will normally takeoff, circle back towards the limbo pole, then pass
across the attempt line and under the bar, then land. If you successfully fly under the
bar, the bar height will be lowered prior to your next turn.
An attempt means you have crossed the attempt line, approaching the limbo bar.
You can make multiple attempts, if necessary, during a turn.
You have anywhere from 10 seconds to five minutes between the moment you first lift
off and the moment you successfully pass under the bar. If you fail to make it under
the bar in time, you lose your turn. (Before the event begins, the host decides the exact
time limit.)

164

You can approach the limbo bar from either direction (i.e., you can cross either
attempt line). For an attempt to count, you must be approaching the limbo bar when
you cross an attempt line. Your aircraft must be airborne when it crosses the attempt
line and when it passes under the bar (i.e., if you taxi, your attempt will not count).
The event continues until each player has made it under the lowest bar height, or has
been disqualified (usually by crashing), or has left the event.
The player with the highest score wins. Your score for each successful turn is:
(time between first liftoff and successful pass) X (height cleared) / 100
Notice that you will achieve or earn the highest score by passing under the bar as soon
as possible after takeoff.
If you did not make it under the bar, your score for that turn is zero.
Events Viewport Display Box-

During the event, a situational screen will appear on your display. This screen serves
several purposes. General notes on the functionality for this window were discussed in
the Autorotation/Deadstick event section.

Pylon Racing
In pylon racing, pilots race their planes around a closed course. Pylon Racing
challenges the pilots nerves and skills as they attempt to round the pylons, avoid midair collisions, and finish first, without cutting any pylons.

165

Selecting Your Name For the Event-

If you have already entered a name in the Settings menu item, this name will be
utilized for single player and multiplayer events. If you have not entered a name, please
do so in the space provided when you select an event. Click OK when completed.
To select a different name for this event, click on the Simulation menu, followed by
the Settings menu item. Next, click the Multiplayer name. This will bring up the
multiplayer options. Click the value found next to the Pilot Name item. Use the
keyboard to input the name you wish to utilize for the events.
Options

As the name suggests, the Options menu item is used to adjust the parameters and
rules for each of the Events. To access the Options menu item, click the Events
menu followed by the Options menu item. Next, from the left hand column, click
on the event for which you wish to adjust the Options. The selections that appear
will be dependent upon the event selected. This section examines the selections
available for the Pylon Racing Options.

166

Laps to complete-

This value determines the number of laps that each participant must complete
in the event. The person who completes the laps in the shortest amount of
time (after penalties) is the winner.
To adjust the number of laps, click on the corresponding value. Enter the
desired value directly from the keyboard or via the mouse wheel.
Cuts Allowed-

This setting dictates the number of cuts (passes inside a pylon) that a racer is
allowed before being eliminated from the event.
To adjust the number of allowable cuts, click on the corresponding value.
Enter the desired value directly from the keyboard or via the mouse wheel.
Cut Penalty (sec)-

This option determines the time penalty that a player receives for each cut they
make during a race. If the player exceeds the number of allowable cuts, they
are eliminated from the race.
To adjust the penalty seconds per cut, click on the corresponding value. Enter
the desired value directly from the keyboard or via the mouse wheel.

167

Three Pylons on Course-

This setting determines whether the course is a three-pylon course or a twopylon course. If Yes is selected, the course is a three-pylon course. If No, the
course is a two-pylon course.
To set this option, click the value in the corresponding column. From the
pull-down list, select either Yes (three pylon course) or No (two pylon course).
Threshold Rules-

In threshold racing, the planes do not actually have to go around the pylon.
Rather, they only have to break the plane of the pylon. This option is only
enabled for two pylon courses. It is grayed out (not applicable) on three pylon
courses.
To determine whether the Threshold Rules will be utilized, click the value in
the corresponding column. From the pull-down list, select either Yes or No.
Distance between pylons 1 and 2-

If you have selected a two-pylon course, this option indicates the distance
between the two pylons. Increasing the value places the pylons farther apart.
To adjust the distance, click on the corresponding value. Enter the desired
value directly from the keyboard or via the mouse wheel.
Distance to pylon 1-

This is the distance from the starting point to pylon number 1. This option is
only applicable to three-pylon courses.
To adjust the distance, click on the corresponding value. Enter the desired
value directly from the keyboard or via the mouse wheel.
Distance between pylons 2 and 3-

If you have selected a three-pylon course, this option indicates the distance
between the pylons two and three. Increasing the value places the pylons
farther apart.
To adjust the distance, click on the corresponding value. Enter the desired
value directly from the keyboard or via the mouse wheel.

Pylon Racing Instructions

You can run a pylon race in either a single player or multiplayer environment.

168

The person who starts the event (the host) decides upon the applicable rules and
parameters. For example, the host can set:

How many pylons mark the course (two or three).

Regular or threshold-style racing (two-pylon races only).

The number of laps in the race.

The distances between pylons.

RealFlight G4 automatically applies the rules you choose, and keeps track of scores.
During the event, an announcers voice will guide you through each phase of the
competition.
Pylon Racing Rules-

A pylon-racing course consists of two or three pylons. Here is an example of a threepylon course:
For both two-pylon and three-pylon races, the object is to takeoff and circle the pylons
(without cutting) in the shortest amount of time. A pylon race usually has two or
more laps. All racers start simultaneously. The race continues until each player is
either finished or disqualified (usually by cutting or crashing).

169

All players start at the same point on the runway. When you hear the horn sound,
takeoff and start the race.
In pylon racing, you always circle the pylons counterclockwise viewed from above
that is, when you come to a pylon you always turn left. As you approach each pylon,
you will hear a voice telling you when to start your turn. When you have made a
successful turn, you will hear a brief tone.
Cutting is illegal. The first time you cut during a race, you are penalized one lap.
The second time you cut, you are disqualified. To avoid being called for a cut, your
entire aircraft must normally go completely around each pylon.
Exception: in a two-pylon style course, you can choose to use threshold-racing rules.
In threshold racing, your aircraft only has to break the plane of the pylon to get
credit for a legal turn. This allows pilots to find independent race lines, which may
reduce collisions during a race. Before the race begins, the host chooses whether the
race will follow regular or threshold rules.
The pilot who finishes the required number of laps in the shortest amount of time wins
the race.
Events Viewport Display Box

During the Event, a situational screen will appear on your display. This screen serves
several purposes.
General notes on this screen were discussed in the
Autorotation/Deadstick event section.

Spot Landing
In a Spot Landing event, pilots take turns trying to touch their aircraft down within
marked zones. Generally, the zones that are more difficult to target have higher point
values. In a multiplayer event, the player with the highest points total wins.

170

Selecting Your Name For the Event-

To select a different name for this event, click on the Simulation menu, followed by
the Settings menu item. Next, click the Multiplayer name. This will bring up the
multiplayer options. Click the value found next to the Pilot Name item. Use the
keyboard to input the name you wish to utilize for the events.
Options-

As the name suggests, the Options menu item adjusts the parameters and rules for
each of the Events. To access the Options menu item, click the Events menu
followed by the Options menu item. Click on the event, located in the left column
that you wish to adjust. The options that appear are dependent upon the event
selected. This section discusses the selections available for the Spot Landing options.

171

Zone Point Values- Zones A through E

The landing zones are divided into five segments. In the default settings, each
segment has a different point value assigned to it based upon degree of
difficulty. Zone A is the most difficult to hit. Therefore, it offers the highest
point value. Zone B, which surrounds the center, offers the second highest
points, followed by Zone C, D and E.
To adjust the point values of the different zones, click on the values in the
column to the right of the respective Zone Points. For example, to adjust the
points for Zone A, click on the corresponding value in the column next to
Zone A. Enter the desired value directly from the keyboard or via the mouse
wheel.
Target Scale-

This option determines the size of the landing targets. To increase the size of
the landing area, enter a larger number in the corresponding value column.
The target size will scale proportionally.
Time to Complete Turn (sec)-

This is the amount of time allotted for players to complete their turn.
Please note: this time begins at takeoff.

172

To adjust the amount of time to complete the event, click on the

corresponding value. Enter the desired value directly from the keyboard or via
the mouse wheel.
Turns Per Event-

This option determines the number of turns allotted to the player for the
Event. The event is over when each player has completed the number of turns
specified. If the Crash Eliminates Players option is enabled, the event can also
end when all of the players have been eliminated due to crashing.
To adjust the number of turns, click on the corresponding value. Enter the
desired value directly from the keyboard or via the mouse wheel.
Crash Eliminates Players-

This option determines whether a crash eliminates a player from the

competition. If No, players will be able to continue their turns regardless of
whether or not they crash. If Yes, the event is over for them as soon as they
crash.
To determine whether a crash eliminates the player, click the value in the
corresponding column. From the pull-down list, select either Yes or No.

Spot Landing Instructions

A spot landing competition can take place in either a single player or multiplayer
environment.

173

The person who starts the event (the host) is responsible for selecting the rules. For
example, you can set:

How much time each player receives per turn.

How many turns allowed per player.

The physical dimensions of the landing target.

Whether a crash automatically disqualifies the player.

Point values of the different zones within the landing target.

RealFlight G4 automatically applies the rules you choose, and keeps track of scores.
During the event, the announcers voice will guide you through each phase of the
competition.
Rules-

The object is to touch down as close as possible to the center of the target. Players
take turns making landing attempts. When your turn comes, you will normally takeoff,
gain altitude and then fly towards the target on a landing approach.

174

A touch down occurs when any part of your airplane or helicopter touches the
ground. A large, visible X marks each touch down on the spot where the aircraft
landed.
Please note: this is not necessarily the point at which the aircraft stopped moving.
Furthermore, you must complete your landing before time expires, thus ending your
turn. If you do not touch down in time, you lose your turn.
The points you receive during a turn are dependent upon where you touch down.
Within the target, each colored zone has a different point value. Normally, the closer
to the center you land, the more points you receive. Your touch down point is the
point on the ground directly below the center of your aircraft, no matter what part of
your aircraft touches first.
The event continues until each player has completed all of his or her turns, or has been
disqualified (usually by crashing), or has left the event. The player with the highest
point total is the winner.
You can only touch down once per turn, so if it looks like you may miss the target, pull
up, circle around, and try again.
The event continues until the players have completed all of their turns, all of the players
have been disqualified (usually by crashing), or everyone has left the event.
The player with the highest total score wins.
Events Viewport Display Box-

During the event, a situational screen will appear on your display.

Autorotation/Deadstick event section provides general notes on this display box.

The

Options
The Options menu item allows you to determine the various settings and parameters
for the respective events. The options available to you are dependent upon the Event
selected.
To access the Options menu item, click on the Events menu followed by the
Options menu item. Next, select the Event for which you would like to view the
Options. For further information as to the Options available for each event, see
the applicable event as discussed previously.

175

End Current Event

This menu item immediately ends the current event. If there are no events in progress,
this menu item is grayed out. If you are in a multiplayer session and are not the person
hosting this session, the option is also grayed out.

Forfeit Turn
This item allows you to forfeit one turn. If you are a multiplayer participant, all other
pilots will take their turns before you can participate again.

176

This item is grayed out if you are playing an event where players do not take turns (e.g.
Pylon Racing).

177

Chapter

Multiplayer Menu
Fly with friends, at the same computer, or over the internet.

he Multiplayer option allows you to fly with others. In fact, you are able to
share the skies with up to seven additional pilots. These other pilots can be
across the street, around the block, or around the world!

There are two ways to link up with the additional pilots; via a LAN (Local Area
Network), or over the internet. In order to do so, you will need a TCP/IP connection,
either through your LAN or an ISP (Internet Service Provider).
Every session requires someone to serve as host. The host initiates the multiplayer
session. When the Host starts a session, other participants may join in.
The Multiplayer menu allows you to access a variety of multiplayer-related features,
functions and options. Clicking the Multiplayer menu brings forth a pull-down
menu, which will look similar to the following screen shot:

179

Host

Join

Disconnect

Boot Player

Publish Hosting Information

Enter MultiMode

Some of these items will be grayed out if they do not apply to the current situation.
For example, you cannot disconnect unless you are currently connected. As such, the
Disconnect menu item is grayed out unless you are in a multiplayer session.
When you participate in multiplayer sessions, the menu commands you will access
depend on whether you are the host or whether you opt to join someone elses session.
These commands also depend upon whether you already have a specific session you
want to join.
Depending on what options the participants utilize, it is possible to have a private
session that is only open to players who know the hosts IP address.

180

Please note: a computers IP address is its internet postal code. It tells other
computers on the internet how to contact that computer. The following sections will
explain more about IP addresses as necessary.
It is also possible to participate in a public session using our list server. The list server
is a publicly available list of open RealFlight G4 sessions. Currently we provide the list
server to all RealFlight G4 owners, free of charge. The list server allows you to
participate in multiplayer sessions with other RealFlight G4 users anywhere in the
world.

IMPORTANT INFORMATION ABOUT THE LIST SERVER: At the time

of this writing we are providing the list server service on a trial basis. This
service may be modified, interrupted or cancelled at any time without notice.
In particular, we make no guarantee about the reliability of this service. To use
this service you must register your product and may need to obtain product
updates. Inclusion of this manual on your RealFlight CD-ROM does not imply
that this service will be available at the time you purchase this product.
Moreover, we reserve the right to bar any individual user, or all users at
individual IP addresses or domains, from using the list server at our discretion.
Abusive behavior, for example, will not be tolerated.

Chatting
During Multiplayer sessions, you may want to chat with other participants. Doing so is
as simple as typing a message much like popular instant messenger programs.
To send a chat message, press the Enter key to bring up the Chat field at the bottom
of the screen. Next, using the keyboard, type the message you wish to send. Press the
Enter key again on the keyboard to send the message.
Please note: all messages are viewable by all participants. RealFlight G4 does not offer
private chat.
Any messages received from other participants will appear at the bottom of the screen.

Host
Every multiplayer session requires one participant to function as the host. If you are
the host, you will be the one who starts the session. When you leave the session one of

181

the remaining participants automatically assumes the role of Host. The host is also the
one who starts and ends the events (Limbo, Pylon Racing, etc.).

Once you have started the session, other players may join in as they wish.
If you opt to broadcast the session to the list server, the session is known as a public
session. The session will be open to all G4 owners searching for multiplayer events.
If you wish to keep the session private, only those participants to whom you have
provided your IP address will be able to join.
The procedures for starting public and private sessions are very similar. In order to
join your session, the participants will usually need to know the IP (Internet Protocol)
address of your computer. The exception is if you are holding the session over a LAN,
in which case the other players do not need to know your IP address. For a public
session, your partners can retrieve your IP from the list server. For a private session,
you must provide the IP address directly to the desired participants. When the session
starts, RealFlight G4 will display your IP in the lower left corner of the main display.
To access the Host menu item, click on the Multiplayer menu followed by the
Host menu item.

182

Host Information-

The Host Information allows you the ability to name your multiplayer session. You
can also choose the maximum number of pilots and whether or not you wish to make
your multiplayer session public or private.

Session Name-

Using the keyboard, enter the name of the session that you will be hosting.
Please note: this is the name of your session, not necessarily your personal
name. In fact, you might find it useful to use a descriptive name such as 3D
Fun Fly. This is particularly useful when other participants are searching for a
likely session to join.
Max Players-

To adjust the maximum number of players allowed in your session, click the
down arrow. Enter the number directly from your keyboard or use the mouse
wheel.
Currently, a multiplayer session may not have more than eight members. If the
host computer is somewhat slow or has a poor internet connection, you may
want to limit the number of participants.
Optional Port Number-

For users that are behind firewalls, you may want to use a port other than the
default port (which is 2302). Most users should leave this field blank.
Broadcast to the List Server-

Clicking this option allows your session to be posted on the list server. This
allows other RealFlight G4 users to join your session. This is a good option if
you are looking for new (or additional) partners to fly with. If you check this
box, you will be prompted for session information (see next section).
If you leave this box unchecked, your session will not be posted on our list
server and you will have a private session. You will have to directly provide

183

your IP address to your multiplayer partners (through phone, email, chat room,
or whatever means you wish). This is a good option if you want to limit your
session to a private group of friends.
If you do not want to broadcast your session information now, you can do so
after the start of the session (see section pertaining to Publish Hosting
Information on page 188).
Finally, please remember that at the time of this writing, we are providing the
list server on a trial basis only. This service may be modified, interrupted or
discontinued at any time without notice.

Join
This option allows you to participate in a Multiplayer session without being the Host of
the session yourself.

To access the Join menu item, click on the Multiplayer menu followed by the
Join menu item.

184

Before you can join a session, you will need two things:

A network connection and

The IP address of the session Host (unless the session is taking place over a LAN
[Local Area Network]).

You can get the IP address directly from the Host (in the case of a private session), or
from our list server (in the case of a public session).
Join Session-

This dialog allows you to select the multiplayer session that you wish to join. It also
provides you with a variety of information pertaining to the various sessions available
to you.

Search Function-

The Search function checks two distinct areas for multiplayer sessions.
RealFlight G4 (at your discretion) will search the list server and the Local
Network for multiplayer sessions.
To determine the Search area, click the down arrow next to the Start button.
This activates the pull-down selections. Click on the location that you wish to
search.
After making your selection, click the Start button to begin the search. When
the search completes, the respective sessions and information appear in the
dialog above. To select one of these sessions, click on the respective session

185

and then click OK. Alternatively, you may double-click on the Session Name
to join.
Note: if you are using an updated version of Windows XP (Service Pack 2 or
later), you may have Windows Firewall installed and running. If this is the
case, Windows Firewall will pop up a warning dialog (similar to that shown
below) the first time you use the Search function. You must select the
Unblock option in order to allow RealFlight G4 to continue searching.

Session Name-

The Session Name column displays the name of all available sessions. If you
have not searched (and found) a session, or entered an IP address, the Session
Name will remain blank.
Host-

This column shows the IP address of the host computer. If you have accessed
the address via the Search function, this information is automatically filled in
for you when you select the session. If you participate in a multiplayer session
via a LAN, you do not need to fill in the IP address. If you participate in a
private session, fill in the IP address here. When completed, click OK to
proceed.
Port-

This information is important if you are attempting to participate in a

multiplayer session and the computer is located behind a firewall or NAT. The
Port Number will route your computers data through the firewall. It is
imperative that this port number matches the port number of the host.

186

Players-

This column shows the users how many players are participating in a given
multiplayer session. The host determines the number of allowable participants.
Latency-

Latency is the amount of time it takes a packet of information to travel from its
source to the destination. The larger the number, the slower the information
travels. High latency can result in sluggishness and lag while running the
simulation. As such, you will want to avoid sessions where the latency number
is high.

Disconnect
This menu item is used to disconnect from, or exit, the multiplayer session.

To access the Disconnect menu item, click on the Multiplayer menu followed by
the Disconnect menu item.
Please note: if you are not currently participating in a multiplayer session, this item will
be grayed out and will not be accessible.

187

Boot Player
This menu item is used to drop a participant from a multiplayer session. It is only
available if you are the Host of the session. Otherwise, this item is grayed out and
inaccessible.

To access the Boot Player menu item, click on the Multiplayer menu followed by
the Boot Player menu item.
The booted player will receive an on-screen message advising him/her that the host
has booted (removed) them from the session.

Publish Hosting Information

You can make your session public (placed on the list server) when you first start the
session. Alternatively, you can do this while the session is in progress by selecting this

188

menu item. When you click OK, RealFlight G4 publishes your session information to
the list server, where everyone can see it.

Please note: at the time of this writing, we are providing the list server on a trial basis
only. This service may be modified, interrupted or discontinued at any time without
notice.

Enter MultiMode
MultiMode allows you to fly with another pilot on the same PC, with each pilot
controlling his or her own aircraft. This feature is ideal for offering personal flight
instruction, practicing formation flights, or simply for chasing one another across the
skies.

189

To access the MultiMode menu item, click on the Multiplayer menu followed by the
MultiMode menu item.

190

MultiMode will split the screen either horizontally (default) or vertically. You can
change this options in the Settings window. Simply click the Simulation menu,
followed by Settings. On the left side of the Settings screen that appears, choose
Multiplayer. On the right, you can adjust the Multimode Screen Layout to
Horizontal or Vertical.
All options available in RealFlight are also available in MultiMode. The difference is
most will function on the half of the screen that currently is active. To determine
which half has the focus or is active, look for the yellow outline. To change focus, click
the half that doesnt have the yellow outline. Youll notice the focus change when you
do so.
For example, if you are flying in MultiMode with a horizontally split screen, you might
notice that the yellow outline is around the top half. If you want to change the aircraft
for the person flying on the bottom half of the screen, first click that half of the
window so it has the focus or is the active screen. Select an aircraft following the
normal procedure.
To exit MultiMode, select Exit MultiMode menu item under the Multiplayer main
menu.

191

10
Chapter

Recordings Menu
Save and play back RealFlight memories.

he Recordings menu is used to start and stop recordings to assist you in your
R/C ventures. RealFlight G4 also allows you to record your flights for later
playback -- complete with audio voiceovers. You can even share your flights
with friends and fellow pilots.

Menu options that are available for Recordings are:

Start/Stop Recording

193

Open Recording

Record Microphone Input

Recordings MRU

Start Recording
Click on the Recording menu followed by the Start Recording menu item.
RealFlight G4 will start recording your flight immediately. An on-screen message will
confirm that the recording has started.

Alternatively, you may also press the keyboards R key to start a recording.
RealFlight will continue recording your flight until you select the Stop Recording
menu item or press R again to stop recording.

194

Stop Recording
The Stop Recording menu item is not visible until the Start Recording menu item
activates. To stop the recording of your flight at any time, click the Recording menu
title, followed by the Stop Recording option. RealFlight G4 will stop recording at this
time. RealFlight G4 automatically saves all recordings for playback later. For
information on how to delete a recording, please see the Open Recording section
which follows.
Alternatively, you may also press the keyboards R key to stop recording.
When RealFlight G4 stops recording, an on-screen message appears which indicates
the default name of the recording that has just been completed. For information on
how to change the name of a recording, please see the Open Recording section
which follows.

Open Recording
This menu item allows you to access the recording files. It also allows you to perform
a variety of modifications to the files such as renaming them or deleting them. To
access the recordings, click the Recording menu title, followed by the Open
Recording menu item.

195

To open a recording, click on the file name. Next, click on the Open button.
Alternatively, you may double-click on the file. Regardless of which method you
utilize, this will start RealFlights Playback Gadget. For more information on the
Playback Gadget, please refer to the information below.
If you wish to rename the recording, simply right click on the respective Recording,
select rename from the drop-down menu and rename the file.
To delete a recording, right click on the Recording file and select Delete from the pulldown list.
Playback Gadget-

When you open a recording, RealFlight G4s playback gadget appears on the screen.
This gadget allows you to control the playback of the recordings using simple mouse
commands. It features DVD-like controls that start, stop, and pause the playback. It is
also possible to modify the playback gadget.

196

If you do not wish to view the playback information, double-click the title bar of the
display box. This will hide the information. To view it once again, simply double-click
the title bar again.
To resize the playback gadget display, position the cursor over the lower right corner of
the frame. Using the mouse drag the frame according to your wishes. Dragging the
frame to the right or left increases or decreases the width of the viewport, respectively.
Clicking on the X in the viewports title tab removes it from the screen and exits the
playback.
Loop Play-

The arrows that forms a circle causes the recording to loop (i.e., play
continuously). The continuous loop is activated when the arrows are
illuminated. To stop the looping, click on the loop button again.

Look at Recording-

Click on the eye to look at the respective Recording. This causes the camera
to treat the recording as its target object, rather than your aircraft. If you have
multiple recordings playing, choose the eye of the Recording you wish to
view.

197

Left/Right Arrows-

The left and right arrows rewind (left) or fast forward (right) the recording.
Alternatively, you may click on the position indicator, hold the mouse button
and drag the indicator to the desired position.

Playback/Pause-

If the recording is paused, the playback button will be the single arrow pointing
to the right. To resume playback of the recording, click this arrow.

If the recording is playing, the playback button will switch to a pause button.
To pause playback, press this button. You may continue at any time by
pressing the playback button once again.

Position of Recording-

The slider bar and position indicator are used to track the progress of the
recording playback.
It is also possible to use the position indicator to select the point at which you
wish the recording to begin playing. Using the mouse drag, position the slider
bar to the position desired.

198

Record Microphone Input

RealFlight G4 also allows you to add your voice or other audio to the recordings. If
selected, the Record Microphone Input menu item activates and allows you to record
audio input to accompany your recording.

Adding your voiceover to the recordings is a fantastic way to create personalized

training lessons. This feature presents you with the ability to create your own Virtual
Flight Instructions that you can share with other RealFlight G4 owners around the
world!

199

Recordings MRU
If you have previously selected a recording, you will note that it appears on a list in the
Recordings menu title. Lists such as this are commonly referred to as Most Recently
Used, or MRU lists. The MRU list is limited to the eight most recently selected
recordings. If you wish to view one of these recordings simply click on the name of
the recording and it will begin.

200

11
Chapter

Training Menu
Practice makes perfect. RealFlights Training Aids make practicing a little more
enjoyable.

ealFlight G4 offers a number of training aids. These training aids are designed
for modelers of all skill levels.

Helicopter pilots will benefit from the Heli Hover Trainer, Heli Orientation
Trainer and the helicopter Virtual Flight Instructions. The Heli Hover Trainer and
Heli Orientation Trainer offer modelers the chance to practice their stick control and
helicopter attitude recognition. With Virtual Flight Instructions, R/C professionals
offer audio and visual instruction on how to perform basic, intermediate and advanced
maneuvers.
Airplane modelers will also benefit from the Takeoff Trainer, Landing Trainer,
Airplane Hover Trainer and Virtual Flight Instructions.

201

Once you click on the Training menu, the following menu options appear:

Takeoff Trainer

Landing Trainer

Heli Hover Trainer

Airplane Hover Trainer

Heli Orientation Trainer

Virtual Flight Instruction

Takeoff Trainer
The Takeoff Trainer offers a great way for first time pilots to learn the basics of taking
off an airplane. With this trainer, you have the ability to adjust wind settings, takeoff
direction, and overall difficult to stay on the runway.

202

To start the trainer, click Takeoff Trainer menu item from the Training menu.
The trainer will start automatically.
The Takeoff Trainer feature is based on RealFlights Flight School flying site. As such,
youll notice that RealFlight automatically uses the Flight School airport. Youll see that
the NexSTAR trainer sitting at the end of the runway, waiting for your inputs. The
goal is to takeoff as straight as possible down the runway, pulling back gently on the
elevator. As you takeoff, youll notice a number of arrows in the sky. These arrows
indicate the path that you should follow. The arrows will appear red in color if you are
on the correct path, blue if you are not.

203

Youll also notice the menus have changed, which well discuss here.
Trainer Menu-

The Trainer Menu contains the following menu items:

204

Reset Aircraft

Boundary

Wind

Direction

Exit
Reset Aircraft-

If you crash or fly too far out of the boundary area, there are three ways to
reset the aircraft:
1. Press the Reset button on the InterLink Elite controller. This is
probably the fastest and simplest method.
2. Press the keyboards space bar.
3. Click the Reset Aircraft menu item

205

Boundary-

The Boundary menu item allows you the change the size of the runway path
for which you must stay inside while taking off. To change the size or the
boundary, select the Boundary menu item from the Trainer menu. A submenu will appear with the following options.

None Eliminates the boundary all together.

Small Creates a tighter boundary which is excellent training for practicing

precise takeoffs.

Medium Creates a medium path boundary.

Large Creates a large boundary.

Once you select a boundary size, youll notice two blue lines on either side of
the runway. During takeoff, you must try to stay between these lines. If you
get too close, they will turn red. Correct the flight path of your airplane so that
you are more centered on the runway.
Wind-

Not everyday can be an ideal day to fly. Every pilot must learn how to takeoff
with different wind conditions. The Wind menu will allow you to adjust the
direction of the wind. When you select the Wind menu item, the following
options will appear.

None Turns the wind off to simulate a calm day.

Crosswind Left This will set the wind to blow from the left of the
aircraft.

Crosswind Right This will set the wind to blow from the right of the
aircraft.

Upwind (Normal) Upwind will set the wind to blow towards the nose of
the aircraft.

Downwind (Dangerous) This will create a tail wind, making it more

difficult to take off due to the decrease in airspeed.

Direction-

The Direction menu will allow you to change the direction in which you take
off. For an R/C pilot, you dont have the luxury of sitting in the airplane, so
you must learn how to control the airplane from any direction. Selecting the
Direction menu will show the following options.

206

Left to Right Take off from the left side of the runway, heading to the
right.

Right to Left Take off from the right end of the runway, heading to the
left.

Exit-

If you wish to leave the Takeoff Trainer and return to the simulation, select the
Exit menu item.

Landing Trainer
The old saying goes, Take offs are easy, landings are the hard part. Once you master
the Takeoff Trainer, the next step is to learn how to land, which is what the Landing
Trainer is designed to do.

To start the Landing Trainer, click the Training menu, followed by the Landing
Trainer menu item.

207

Youll notice that RealFlight switched airports to Flight School, if you were not there
already. For this training session, youll be piloting Hobbicos NexSTAR. Youll also
have options, should you wish, to adjust where to start the landing, wind direction, and
how difficult it should be to hit the runway.

For landings, its important to understand the different legs during the approach to the
runway.

208

When you start the Landing Trainer, youll notice a new menu has appeared.
Trainer Menu-

The Trainer Menu contains the following menu items:

Reset Aircraft

Boundary

Wind

Direction

Leg

Exit
Reset Aircraft-

If you crash or fly outside the boundary, there are three ways to reset the
aircraft:
1. Press the Reset button on the InterLink Elite controller. This is
probably the fastest and simplest method.

209

2. Press the keyboards space bar.

3. Click the Reset Aircraft menu item.
Boundary-

The Boundary menu item allows you the change the size of the runway path in
which you must land between. To change the size or the boundary, select the
Boundary menu item from the Trainer menu. A sub-menu will appear with
the following options.

None Eliminates the boundary all together.

Small Creates a tighter boundary which is excellent training for precise

landings.

Medium Creates a medium path boundary.

Large Creates a large boundary.

Once you select a boundary size, youll notice two blue lines on either side of
the runway. During your landing, you must try to stay between these lines. If
you get too close, they will turn red. Correct the flight path of your airplane so
that you are more centered on the runway.
Wind-

Every pilot must learn how to land with different wind conditions. In some
respects, this can be more difficult than takeoffs, since you must learn how to
deal with different wind conditions for each leg of the approach. The Wind
menu will allow you to adjust the direction of the wind. When you select the
Wind menu item, the following options will appear.

None Turns the wind off to simulate a calm day.

Crosswind Left This will set the wind to blow left across the runway.

Crosswind Right This will set the wind to blow from the right across the
runway.

Upwind (Normal) Upwind will set the wind to blow towards the nose of
the aircraft as you are on your final leg.

Downwind (Dangerous) This will create a tail wind during the final leg,
making it more difficult to land due to the decrease in airspeed.

210

Direction-

Its important to learn how to land from any direction. This menu item will
change the approach direction to learn the controls from a different aspect.
The choices that appear when you select the Direction menu item are as
follows.

Left to Right This will set you up to land on the runway from the left
end flying towards the right.

Right to Left - This will set you up to land on the runway from the right
end flying towards the left.

Leg-

The Leg menu item allows you to practice each leg of the approach. The
options are as follows.

Downwind This sets the aircraft up on the downwind side, or parallel to

the runway. From here, you must fly the Downwind, turn to Base, and
then the Final for the landing.

Base This sets the aircraft up for the Base leg of the approach. You
must complete the Base leg and then turn to the Final leg prior to landing.

Final The Final leg will set you up for the landing.

When the training lesson begins, the NexSTAR will be placed at the beginning
of the Leg you choose. Simply hit the Reset button on the InterLink Elite to
begin flying.
Exit-

If you wish to leave the Landing Trainer and return to the simulation, select
the Exit menu item.

Heli Hover Trainer

The Heli Hover Trainer offers you a great way to learn how to precisely control a
helicopter in a hover. With the Heli Hover Trainer, you pick which channels you wish
to control and RealFlight will take care of the rest for you.

211

To start the trainer, click Heli Hover Trainer menu item from the Training menu.
The trainer will start automatically.
Youll notice a circle on the ground. This circle represents the training boundary. If
your helicopter ventures beyond this boundary, it will break apart and the session will
begin once again. Youll also note two X marks within the boundary. The circle
represents the true center of the boundary, the X represents the current location of
your helicopter. The goal is to control the helicopter in a stable hover, keeping it as
close to the center of the circle as possible.

212

Youll also notice that the menu options have changed.

Trainer Menu-

The Trainer Menu contains the following menu items:

213

Reset Aircraft

Boundary

Crashes

Exit
Reset Aircraft-

If you crash or fly outside the circle, there are three ways to reset the aircraft:
1. Press the Reset button on the InterLink Elite controller. This is
probably the fastest and simplest method.
2. Press the keyboards space bar.
3. Click the Reset Aircraft menu item.
Boundary-

The Boundary menu item allows you to change the size of the circle, or
eliminate it altogether. To change the size of the boundary, select the
Boundary menu item from the Trainer menu. A drop down menu will
appear with the following options.

214

None Eliminate the boundary circle.

Small Creates a small circle.

Medium Creates a medium sized circle.

Large Creates a large circle.

Crashes-

After a crash, RealFlight may automatically reset your helicopter for you, if so
desired. This option is on by default. If you would prefer to turn this option
off, select the Crashes menu item, then select the Automatically Reset
Aircraft. If a checkmark appears next to this menu item, then this feature is
activated. If the checkmark does not appear, it is not active.
If Automatically Reset Aircraft is enabled, you may adjust how quickly the
reset happens. To adjust this delay, select the Crashes menu item followed by
the Reset Delay menu item. Four options will be available to you:

None No delay will be set. The aircraft will reset immediately.

Short The aircraft will reset approximately one second after it crashes.

Medium The aircraft will reset approximately three seconds after it

crashes.

Long The aircraft will reset approximately six seconds after it crashes.

Exit-

If you wish to leave the Heli Hover Trainer and return to the simulator, select
the Exit menu item.
Orientation Menu-

The Orientation menu allows you the option to select the position and attitude of the
heli when the session begins or the helicopter is reset.

215

A checkmark will appear next to the currently selected orientation. The options
available are:

Random Upright The heli will start in the upright position, but it will randomly
face either to the right, left, nose out, or nose in.

Random Inverted The heli will start in the inverted position, but it will randomly
face either to the right, left, nose out, or nose in.

Nose Out The heli will start upright, facing nose out. This option is the best
selection for beginning heli pilots.

Nose In The heli will start upright, facing nose in.

Left The heli will start upright, facing to the left.

Right The heli will start upright, facing to the right.

Nose Out Inverted The heli will start inverted, facing nose out.

Nose In Inverted The heli will start inverted, facing nose in.

Left Inverted The heli will start inverted, facing to the left.

Right Inverted The heli will start inverted, facing to the right.

216

Control Menu-

The Control menu allows you to select which channel or channels to control. All other
channels are controlled by RealFlight, allowing you to learn just the controls you wish,
and adding more as you become more comfortable and confident.

A checkmark will appear in the menu next to the currently selected item. Your options
are:

Pitch Only You control only the pitch of the heli, RealFlight will control the roll,
yaw, and throttle.

Roll Only You control only the roll of the heli, RealFlight will control the pitch,
yaw, and throttle.

Yaw Only You control only the yaw of the heli, RealFlight will control the roll,
pitch, and throttle.

Throttle Only You control only the throttle of the heli, RealFlight will control the
roll, yaw, and pitch.

Throttle, Pitch You control both the throttle and pitch of the heli, RealFlight will
control the roll, and yaw.

Throttle, Roll You control both the throttle and roll of the heli, RealFlight will
control the pitch, and yaw.

217

Throttle, Yaw You control both the throttle and yaw of the heli, RealFlight will
control the roll, and pitch.

Throttle, Pitch, Roll, Yaw You control all channels for the heli.

Airplane Hover Trainer

The Airplane Hover Trainer offers you a great way to learn how to control an
aerobatic airplane in a torque roll. With the Airplane Hover Trainer, you pick which
channels you wish to control. RealFlight automatically controls the rest.

To start the trainer, click Airplane Hover Trainer menu item from the Training
menu. The trainer will start automatically.

218

Youll notice a circle on the ground. This circle represents the training boundary. If
your airplane ventures beyond this boundary, it will break apart and the session will
begin once again. Youll also not two X marks within the boundary. One represents
the true center of the boundary; the second is your airplane location. The goal is to
control the airplane in a stable hover, keeping it as close to the center of the circle as
possible.
Youll also notice the menus have changed, which well explain here.
Trainer Menu-

The Trainer Menu contains the following menu items:

219

Reset Aircraft

Boundary

Crashes

Exit
Reset Aircraft-

If you crash or fly outside the circle, there are three ways to reset the aircraft:
1. Press the Reset button on the InterLink Elite controller. This is
probably the fastest and simplest method.
2. Press the keyboards space bar.
3. Click the Reset Aircraft menu item.
Boundary-

The Boundary menu item allows you the change the size of the circle, or
eliminate altogether. To change the size or the boundary, select the Boundary
menu item from the Trainer menu. A drop down menu will appear with the
following options.

220

None Eliminates the boundary circle.

Small Creates a small circle.

Medium Creates a medium-sized circle.

Large Creates a large circle.

Crashes-

After a crash, RealFlight may automatically reset your aircraft for you, if so
desired. This option is on by default. If you would prefer to turn this option
off, select the Crashes menu item, then select the Automatically Reset
Aircraft. If a checkmark appears next to this menu item, then this feature is
activated. If the checkmark does not appear, it is not active.
If Automatically Reset Aircraft is enabled, you can adjust how quickly the reset
happens. To adjust this delay, select the Crashes menu item followed by the
Reset Delay menu item. Four options will be available to you:

None No delay will be set. The aircraft will reset instantaneously.

Short The aircraft will reset approximately one second after it crashes.

Medium The aircraft will reset approximately three seconds after it

crashes.

Long The aircraft will reset approximately six seconds after it crashes.

Exit-

If you wish to leave the Airplane Hover Trainer and return to the simulator,
select the Exit menu item.
Orientation Menu-

The Orientation menu allows you the option to select the position and attitude of the
helicopter when the session begins or the airplane is reset.

221

A checkmark will appear next to the currently selected orientation. The options
available are:

Random The airplane will start in a random position, with either the top, bottom,
left side or right side facing you.

Top The airplane will start with the top of the aircraft facing you.

Bottom The airplane will start with the bottom of the aircraft facing you.

Left The airplane will start with the left side of the aircraft facing you.

Right The airplane will start with the right side of the aircraft facing you.

Control Menu-

The Control menu allows you to select which channel or channels to control. The
remaining channels are controlled by RealFlight, allowing you to learn just the controls
you wish, and adding more as you become more comfortable and confident.

222

A checkmark will appear in the menu next to the currently selected item. Your options
are:

Elevator Only Check this to control only the elevator of the aircraft. RealFlight
will control the throttle, ailerons, and rudder for you.

Aileron Only Check this to control only the ailerons of the aircraft. RealFlight
will control the throttle, elevator, and rudder for you.

Rudder Only Check this to control only the rudder of the aircraft. RealFlight will
control the throttle, ailerons, and elevator for you.

Throttle Only Check this to control only the throttle of the aircraft. RealFlight
will control the elevator, ailerons, and rudder for you.

Throttle, Elevator Check this to control the throttle and elevator of the aircraft.
RealFlight will control the ailerons and rudder for you.

Throttle, Aileron Check this to control the throttle and ailerons of the aircraft.
RealFlight will control the elevator and rudder for you.

Throttle, Rudder Check this to control the throttle and rudder of the aircraft.
RealFlight will control the elevator and ailerons for you.

Throttle, Aileron, Elevator, Rudder Check this to control all four channels. You
will not receive any assistance from RealFlight.

223

Heli Orientation Trainer

As you become more proficient with hovering a helicopter, you can test your skills
with the Heli Orientation Trainer. The Heli Orientation Trainer challenges you to
keep your helicopter in the same location as the trainer helicopter. As you succeed in
doing so, the trainer helicopter will move, and the level of difficulty will increase.

To start the trainer, select Heli Orientation Trainer menu item from the Training
menu.
The Heli Orientation Trainer has a number of different levels, each with an increasing
level of difficulty than the previous. To pass a level you must hover your helicopter in
close proximity to the trainer helicopter. As you do so, the trainer helicopter will turn
from blue to red, and the progress bar at the top of the screen will increase, indicating
that your task is nearly complete.

224

In the upper right corner, a countdown timer is visible. This is the amount of time you
have to fill the progress bar and complete the task. If you fail to do so, both the timer,
and the progress bar will reset to zero. You must begin once again.
The number displayed in the upper left corner indicates the number of locations the
trainer helicopter will stop for the current level. It will also indicate how many of these
locations you have completed. For example, if it displays 1/3, you have successfully
completed one spot out of three for the current level.
As you advance to the next level, you may be responsible for controlling more
channels, the allotted time might also decrease and the trainer heli will stop in more
locations. Additionally, you might experience any combination of these circumstances
to increase the difficulty.
Heli Orientation Menu-

The Heli Orientation menu is the only menu accessible while the trainer is running.
Two options are available in the Heli Orientation menu:

225

Select Level-

A drop-down menu will display the levels available to you. For example, if you
have only progressed to Level 2, you will not be able to access Level 3 or
higher in this menu.
A checkmark will appear next to the level you are currently flying.
Exit-

To return to the simulator, select Exit to leave the Heli Orientation Trainer.

Virtual Flight Instruction

RealFlight Generation 4 includes on-screen flight training from some of R/Cs best
pilots. John Glezellis, Frank Noll Jr., Jason Shulman, Pete Niotis, Todd Bennett, Brian
Bremer and Jim Bourke are your instructors taking you through a variety of skill levels
of R/C. There are basics for beginners as well as more advanced maneuvers for
intermediate pilots. G4 also includes instructions on how to perform some of todays
hottest 3D flight maneuvers! G4 includes voice instruction as well as an on-screen

226

radio that shows the exact movements that the instructor is using. VFI is the perfect
training tool for pilots of all skill levels.

To access the VFI menu item, click the Training menu followed by the Virtual
Flight Instruction menu item. Alternatively, you may also access the VFI by
pressing the V key on the keyboard. Determine whether you wish to participate in a
helicopter or airplane training session. Open the respective genre by clicking the [+]
(plus) or double-clicking the listing. Next, select the pilot you wish to view. To select
and begin your training, either double-click the respective maneuver or highlight the
maneuver and click OK.

227

By default, G4s radio gadget appears on-screen. This digital transmitter is a visual
guide to display the stick inputs, in real-time, utilized for the recordings. For additional
information, please refer to the Radio- section on page 247.

228

229

12
Chapter

View Menu
Adjust your vantage point, change your perspective and more.

his menu allows you to adjust the various view-related features and functions
for the simulation. The View menu adjusts what you are looking at as well as
where you are looking from.

Show

Camera Type

Camera Position

231

Look at

Quick Look

Zoom Type

Zoom In

Zoom Out

Zoom Reset

Head Tracking

Show
The Show menu item is used to determine whether to show or hide scenery objects in
the airport.

232

Selecting this item brings forth a pull-down menu with a list of items you can show
(make visible within the simulation) or hide (remove from visibility). To show items,
check them in the drop-down menu. To hide items, click on them to remove their
respective checkmark.
If the frame rate slows dramatically, try eliminating some of the items listed in the
Show menu title. This will improve the frame rate.
To access this menu item, click on the View menu followed by the Show menu item.

Camera Type
The Camera Type menu item determines the Camera Type for the active viewport.
Each viewport is independently adjustable. Select from a Fixed Position, Cockpit or a
Chase view.

If more than one viewport is open, click on the viewport that you wish to modify.
This becomes the active view in the simulation. To access the Camera Type
adjustments, click on the View menu followed by the Camera Type menu item.
Select your preferred view from the pull-down list.

233

Alternatively, you may press the keyboards C key to toggle through the available
Camera Type options.
Please note: some airports do not allow Camera Type adjustments.
Fixed Position-

In this mode, the camera remains in a fixed, stationary position. The position is
determined by the Camera Position setting.
Cockpit-

The Cockpit selection places the camera inside the aircraft as if you were a full-scale
pilot.
To magnify the view or zoom in on the selected item, press the [+] (plus) key on the
keyboard. Each time you press the [+] (plus) key or select the Zoom In menu item,
the zoom level increases incrementally. Alternatively, you may select the Zoom In
option from the View menu.
To decrease the magnification, or zoom away from the selected item, press the [-]
(minus) key on the keyboard. Each time you press the [-] (minus) key or select the
Zoom Out menu item, the zoom level decreases incrementally. Alternatively, you may
select the Zoom Out option from the View menu.
Chase-

The Chase mode positions the camera behind the aircraft. The camera will follow the
aircraft as it moves.
To magnify the view or zoom in on the selected item, press the [+] (plus) key on the
keyboard. Each time you press the [+] (plus) key or select the Zoom In menu item,
the zoom level increases incrementally. Alternatively, you may select the Zoom In
option from the View menu.
To decrease the magnification, or zoom away from the selected item, press the [-]
(minus) key on the keyboard. Each time you press the [-] (minus) key or select the
Zoom Out menu item, the zoom level decreases incrementally. Alternatively, you may
select the Zoom Out option from the View menu.

Camera Position
This menu item determines where the camera will be situated. Depending upon the
airport selected, there may be one or more Pilot Spawn locations to use as camera
positions.

234

RealFlight G4 automatically picks the default Pilot Spawn for the airport that you have
loaded.
To change the setting, click on the viewport to you wish to modify. This becomes the
active view in the simulation. To access the Camera Position adjustments, click on the
View menu followed by the Camera Position menu item. Select your preferred view
from the drop-down list.
You may also press the keyboards X key to toggle through the available Camera
Position options. If the airport has two pilot spawn locations, for example, pressing
the X key will toggle back and forth between these two locations.

Look At
This menu item changes what the camera looks at. Usually you will want the camera to
remain focused on your aircraft.

235

Click on the viewport that you wish to modify. This becomes the active view in the
simulation. To access the list of things to look at, click on the View menu followed by
the Look At menu item. Then select an item to look at. For example, if you are in a
multiplayer or MultiMode session, the other players in the session will be listed in the
popup menu. Select a player to look at his/her aircraft.

Quick Look
This feature allows you to quickly glance at an object. When you activate this option,
the camera briefly looks at the selected item and then returns to the previous vantage
point for the active viewport.

236

Click on the viewport that you wish to modify. This becomes the active view in the
simulation. To access the Quick Look menu item, click on the View menu followed
by the Quick Look menu item.
Using the InterLink Elite controller, you can also active the Quick
Look options with the QuickSelect buttons. By pressing up on the
Data Lever, RealFlight will briefly change the camera to look at the
Wind Sock. Pressing down will briefly bring the Ground into view.

Alternatively, after you have activated the correct viewport, you can press a key on your
keyboard to activate the Quick Look feature. The up arrow will look at the windsock,
and the down arrow will look at the ground.

Zoom Type
The Zoom Type menu item allows you to change the type of zoom used in the
simulation.

237

Click on the viewport that you wish to modify. This becomes the active view in the
simulation. To access the Zoom Type menu item, click on the View menu followed
by the Zoom Type menu item. Select the Zoom Type option that accomplishes your
goal. You may choose between Manual, Autozoom, and Keep Ground in View.
Alternatively, after you have activated the correct viewport, press the keyboards Z
key. Each time you press the Z key you will toggle to the next Zoom Type.
Autozoom-

This zoom type adjusts the zoom range based on the distance of the aircraft from the
pilot. The camera automatically zooms in as the aircraft gets further from the pilot and
then automatically zooms out as the aircraft gets closer to the pilot.
Keep Ground in View-

This zoom type adjusts the camera so that the aircraft and the ground are always in
view. This is the only zoom type that disallows zooming in and out.
Manual-

This enables the standard view with zoom capabilities. See the Zoom In and Zoom Out
sections below for more information.

238

Zoom In
Once you have selected the type of zoom that you desire, RealFlight allows you to
customize it further by zooming in.

Click on the viewport that you wish to modify. This becomes the active view in the
simulation. To access the Zoom In menu item, click on the View menu followed by
the Zoom In menu item.
Alternatively, after you have activated the correct viewport, press the [+] (plus) key on
your keyboard. Each time you press the [+] (plus) key you will zoom in
incrementally.

Zoom Out
Once you have selected the type of zoom that you want you can customize it further
by zooming out. Zooming Out decreases the magnification.

239

Click on the viewport that you wish to modify. This becomes the active view in the
simulation. To access the Zoom Out menu item, click on the View menu followed by
the Zoom Out menu item.
After you have activated the correct viewport, you may also press the [-] (minus) key
on your keyboard. Each time you press the [-] (minus) key you will zoom out
incrementally.

Zoom Reset
This selection resets the zoom magnification level to its default value. This is useful if
you are zoomed way in or way out and want to return quickly to the default level of
magnification.

240

Click on the viewport that you wish to modify. This becomes the active view in the
simulation. To access the Zoom Reset menu item, click on the View menu followed
by the Zoom Reset menu item.
Once you have activated the correct viewport, you may also press the Backspace key
on your keyboard to reset the zoom level.

Head Tracking
RealFlight G4 is compatible with TrackIR from NaturalPoint. With a TrackIR plugged
into your computer, you can control the camera with the movement of your head as if
you are at the field looking around.

241

For example, if you are flying at a high altitude and wish to line up with the runway, at
a flying field you would look down briefly. With the TrackIR, you would do the same
at your computer. With a small movement of your head, you can look down at the
runway and back up to your aircraft.
For more information about TrackIR, and where to purchase one, visit NaturalPoints
website at:
http://www.naturalpoint.com/trackir/

242

13
Chapter

Window Menu
Tools to add more excitement to your RealFlight enjoyment.

he Window menu allows you to manage the existing windows or viewports, to

create new ones, and to select from recently used Windows. The Window
menu also gives you access to a variety of on-screen gadgets that offer realtime information about your current flight.

The Window menu offers the following options:

Show Title Bar

243

Gadgets

Arrange

Close All

Window list

Show Title Bar

This menu item determines whether or not the G4 title bar is displayed on the screen.
By default, the title bar is enabled.

To access this menu item, click on the Window menu followed by the Show Title
Bar. This will remove the RealFlight Generation 4 title bar from the screen. Please
note: removing the title bar also eliminates the ability to minimize or maximize the
screen.

244

Gadgets
A Gadget is an on-screen display that provides you with information pertaining to a
certain item in your simulation. To access the Gadgets menu item, click the Window
menu followed by the Gadgets menu item. This will open the list of gadgets for the
simulation.

Selecting this menu item will bring up the Gadgets list as follows:

NavGuides

Radio

Binocular

Viewport

Variometer

Console

245

Chat

Edit NavGuides

Radio Mode (gadget only)

NavGuides-

A NavGuide is an on-screen display that allows you to view some basic information
pertaining to your aircraft. If you wish to alter the contents of the NavGuide, please
refer to the Edit NavGuides section later in this chapter.

To access the NavGuides, click the Window menu title, followed by the Gadgets
menu item. Next, click the NavGuides menu item. You may also bring up the
NavGuides by pressing the keyboards 1 key.
You may also load the NavGuides using the InterLink Elite with
the QuickSelect buttons. Press the Menu/Select button. Then
press down twice on the Data Lever until the NavGuides tab is
highlighted. It looks like an aircraft gauge. Press the Menu/Select
button again to activate the NavGuides. Repeat these steps to
remove the NavGuides from the screen.
When the NavGuides are active, an overlay screen will appear on your display. This
screen displays the NavGuides information to you.
If you do not wish to view this information, double-click on the title bar of the display
box. This hides the information. To view it once again, simply double-click the title
bar.
Clicking on the X in the title tab of the frame will remove it from the screen, entirely.
Items included by default in the NavGuides are the following:
Altitude (ASL)-

This option displays the altitude for the respective aircraft above sea level.
Even though the aircraft may be taxiing on the runway, the altitude may reflect
hundreds or thousands of feet, if applicable.

246

Heading-

This option displays the heading of the aircraft. The heading is displayed in
degrees, as they would appear on a compass. 0 degrees is North, 90
degrees is East, 180 degrees is South and 270 degrees is West.
Airspeed-

This option displays the airspeed for the aircraft.

RPM-

This option indicates the current revolutions per minute, or RPMs, for the
engine.
Graphics Frames/Sec-

This is an abbreviated version of Frames per Second, or FPS. While the data
displayed is not relevant to your aircraft, it is used to provide you with
feedback on how your computer is performing at any given time. The higher
the frames per second, the smoother the simulation will appear.
Wind-

This option displays the current wind speed at the flying site.
Radio-

The on-screen radio display is useful for many facets of flight. For example, when
used in conjunction with Virtual Flight Instruction, this allows you to see real-time
control input from the professionals. Observing the link between controller
movements and aircraft performance will advance your knowledge and understanding
of a maneuver.

To access the Radio, click the Window menu title, followed by the Gadgets menu
item. Next, click the Radio menu item.

247

You may also bring up the Radio by pressing the keyboards 2 key.
You may also load the Radio using the InterLink Elite with the
QuickSelect buttons. Press the Menu/Select button. Then press
down three times on the Data Lever until the Radio tab is
highlighted. Press the Menu/Select button again to activate the
on-screen Radio. Repeat these steps to remove the Radio from the
screen.
If you click the on-screen radio, the entire viewport is displayed, including the title bar.
To resize the viewport, position the cursor over the lower right corner of the
viewports frame. Using the mouse, drag the frame according to your wishes. If you
drag it downward, the vertical size of the viewport will increase. Dragging the frame to
the right or left increases or decreases the width of the viewport respectively.
Clicking on the X in the title tab of the frame removes it from the screen.
Binocular-

The Binocular option will show a perfectly zoomed aircraft, as if you were looking
through a pair of binoculars. The background of the viewport box becomes
transparent. This provides a visual indicator alerting you that you are using binocular
vision.

248

The Binocular option is a great way to see the control surfaces on an aircraft that is too
far away to see in the Main View. Although not realistic, it does help to see the control
input.
To access the Binocular menu item, click the Window menu title, followed by the
Gadgets menu item. Next, click Binocular.
You may also bring up the Binocular option by pressing the keyboards 3 key.
You may also load the Binocular viewport using the InterLink Elite
with the QuickSelect buttons. Press the Menu/Select button.
Then press down four times on the Data Lever until the Binocular
tab is highlighted. Press the Menu/Select button again to activate
the Binocular viewport. Repeat these steps to remove the Binocular
viewport from the screen.
Clicking the Binocular viewport will display the title bar and frame. To resize the
viewport, position the cursor over the arrow indication found in the lower right corner
of the viewports frame. Click and hold on the arrow. Using the mouse, drag the
frame according to your wishes. If you drag it downward, the vertical size of the
viewport will increase. Dragging the frame to the right or left increases or decreases
the width of the viewport, as appropriate.
Clicking on the X in the title tab of the frame removes the frame from the screen.
Viewport-

The Viewport menu item allows you to open up a smaller window to you can adjust
independently from the main simulator screen. This works much like a picture-inpicture features found on many TVs.

249

Once you create a new viewport, you can resize or reposition it by dragging with your
mouse. You can also fully adjust all the viewports properties (zoom level, vantage
point options, etc.), independent of any properties of the main window.
To access the Viewport menu item, click on the Window menu followed by the
Gadgets menu item. Then select Viewport.
You may also bring up the Viewport by pressing the keyboards 4 key.
You may also load the Viewport using the InterLink Elite with the
QuickSelect buttons. Press the Menu/Select button. Then press
down five times on the Data Lever until the Viewport tab,
pictured with a video camera, is highlighted. Press the
Menu/Select button again to activate the Viewport. Repeat these
steps to remove the Viewport from the screen.
To change the vantage point options and features, use the commands found in the
View menu. Ensure that the viewport you wish to modify is the active viewport, or the
modifications will not take effect.
Clicking on the X in the viewports title tab removes it from the screen.

250

Variometer-

A variometer is an instrument designed to indicate the rate of climb or descent of an

aircraft. The variometer is useful to pilots flying powered aircraft so they can ascertain
that level flight is maintained. This is useful during turning maneuvers. Glider pilots
typically make the most use of a variometer, to help determine the areas of rising or
sinking air currents.

To access the Variometer, click the Window menu title, followed by the Gadgets
menu item. Next, click the Variometer menu item.
You may also bring up the Variometer by pressing the keyboards 5 key.
You may also load the Variometer using the InterLink Elite with the
QuickSelect buttons. Press the Menu/Select button. Then press
down six times on the Data Lever until the Variometer tab,
pictured with a sailplane, is highlighted. Press the Menu/Select
button again to activate the Viewport. Repeat these steps to remove
the Variometer from the screen.
The variometer available in RealFlight also offers an audio indicator, much like the real
instrument. As the rate of climb increases, the pitch in the audio tone will increase, as
well. The opposite holds true, as the descent of the aircraft increases, the pitch in the
audio tone decreases accordingly.
If you wish to turn off the audio ques, click the button with the speaker symbol in the
lower right corner on the variometer. To turn the audio back on, click the button once
again.
The variometer in RealFlight G4 is split into two parts. The left side of the variometer
includes a status meter which indicates whether the aircraft is ascending, descending or
maintaining level flight. If the bar is in the green, the aircraft is rising. If it is in the red,

251

then the aircraft is descending. If it remains stationary in the middle, the aircraft is
maintaining its altitude. The farther the bar moves from the center, the faster the
change in altitude. On the right, there are three readouts that offer the following.

Rate This indicates the rate of change in altitude.

ASL This shows the altitude above sea level.

AGL This indicates the altitude above ground level.

Clicking the Variometer viewport will display the title bar and frame. Clicking on the
X in the title tab of the frame removes the frame from the screen.
Console-

The Console, and its related commands, will generally be used only by RealFlights
power users or those with advanced knowledge of gaming systems, etc. As such, we
will simply scratch the surface of the Console in this manual. For additional
information and assistance, we encourage users to visit the RealFlight forums at::
http://www.knifeedge.com/forums/
To access the Console, press the ~ key. A complete list of commands is available by
typing help in the command line and pressing Enter.
Chat-

Chatting offers the ability to communicate with other RealFlight players during a
multiplayer session. Select this menu item to bring up the chat field at the bottom of
the simulator screen. To send a message, type your message in the field and press
Enter on the keyboard.
Alternatively, press the Enter key first to bring up the Chat field at the bottom of the
screen. Next, using the keyboard, type the message you wish to send. Press the Enter
key again on the keyboard to send the message.
Please note: all messages are viewable by all participants. RealFlight G4 does not offer
private chat.
Any messages received from other participants will appear at the bottom of the screen.
Edit NavGuides-

This menu item allows you to modify the data displayed in the NavGuides box.
To access the Edit NavGuides feature, click the View menu title, followed by the
Gadgets menu item. Next, click the Edit NavGuides menu item.

252

Modifying the NavGuides-

To add any of the options from the left column to the NavGuides display,
click in the box next to the respective item.
The pane below the list of the Edit NavGuides dialog box contains a
description of the respective item.
The Reset To Basic button returns all NavGuides to their default values and
options. If you wish to choose all items in the NavGuides list, click the Select
All button. All NavGuides items will then be shown in the on-screen display.
To remove all items from the list, click the Select None button.
The NavGuides available are listed in the following table:
Option

Description

Aircraft: Altitude (AGL)

Check this item to display the current altitude of the

aircraft above ground level.

253

Aircraft: Altitude (ASL)

Check this item to display the current altitude of the

aircraft above sea level.

Aircraft: Altitude (ATL)

Check this item to display the current altitude of the

aircraft compared to the terrain below. This option does
not account for water.

Aircraft: Altitude (AWL)

Check this item to display the current altitude of the

aircraft above the body of water at the airport.

Aircraft: G Force

Check this item to display the gravitational load of the

aircraft is experiencing as felt by the pilot.

Aircraft: G Force Total

Check this item to display the gravitational load of the

aircraft is experiencing in any direction.

Aircraft: Ground Speed

Check this item to display the current ground speed of

the aircraft.

Aircraft: Heading of Aircraft

Check this item to display the current heading of the

aircraft. This heading is displayed in degrees, as they
would appear on a compass. 0 degrees is North, 90
degrees is East, 180 degrees is South and 270
degrees is West.

Aircraft: X Position of Aircraft

Check this item to display the current X position of the

aircraft.

Aircraft: Y Position of Aircraft

Check this item to display the current Y position of the

aircraft.

Airspeed: Speed of Aircraft

Check this item to display the current airspeed of the

aircraft.

Engine: Battery Remaining

Check this item to display the remaining capacity in the

battery pack.

Engine: Current Draw

Check this item to display the amount of current that the

motor is draining from the battery pack.

Engine: Fuel Remaining

Check this item to display the amount of fuel remaining.

Engine: Motor Efficiency

Check this item to display the efficiency of the electric

motor.

Engine: Power In

Check this item to display the amount of power being

transferred to the electric motor.

Engine: Power Out

Check this item to display the amount of power being

generated by the engine.

Engine: RPM

Check this item to display the RPMs of the engine.

Note: this measurement does not take into account any
gear reduction which might be utilized.

Engine: Voltage

Check this item to determine the voltage across the

electric motor.

Helicopter: Main Rotor RPM

Check this item to display the current main rotor RPM of

the helicopter.

Helicopter: Tail Rotor RPM

Check this item to display the tail rotor RPM of the

helicopter.

Pilot: Distance to Aircraft

Check this item to display the current distance from the

pilot to the aircraft.

Pilot: Field Of View

Check this item to display the field of view angle for the
main window.

254

Pilot: Height (AGL)

Check this item to display the height of the pilot above

the surface below, water or ground.

Pilot: Height (ASL)

Check this item to display the height of the pilot above

sea level.

Pilot: Height (ATL)

Check this item to display the height of the pilot above

the terrain, not including any body of water.

Pilot: Height (AWL)

Check this item to display the height of the pilot above

the body of water at the airport.

Pilot: Look Direction

Check this item to display the compass direction in

which the pilot is looking.

Pilot: Zoom Magnification

Check this item to display the amount of zoom being

utilized; 1 is equivalent to normal eyesight.

System: Graphics Frame Rate

Check this item to display the number of times the

screen updates per second.

System: Physics Frame Rate

Check this item to display the number of times the

physics system updates per second.

Wind Direction

Check this item to display the direction that the wind is

blowing.

Wind Speed

Check this item to display the velocity of the wind at the

current time.

Wind Updraft

Check this item to display the velocity of the wind in the

upward direction.

Color-

This setting adjusts the Color for the selected item. To select an alternate
Color, click on the color swatch. This will open the color palette dialog and
you may choose an alternate color for the item.
Show only when value is between-

Click on the box to activate the option for Show only when value is
between. If the aircraft parameter falls within the specified range, the selected
item will appear in the NavGuides. If the parameter is not within the specified
range, the item will not be shown.
To adjust the range, click on the respective value box and input the value via
your keyboard.
Change color when value is between-

Click on the box to activate the option for Change color when value is
between. If the aircraft parameter falls within the desired range, the selected
item will appear in the NavGuides in the alternate color. If the parameter is
outside of the specified range, the item will be shown in the primary color.
To adjust the range, click on the respective value box and input the value via
your keyboard.

255

Radio Mode (gadget only)-

This option allows you to change the Mode in which the on-screen radio is displayed.
For example, if you prefer to fly with the throttle and rudder on the left stick, and
ailerons and elevator on the right stick, then you fly Mode 2. Some modelers prefer
Mode 1. In this mode, the left stick controls the rudder and elevator; the right stick
controls the throttle and ailerons.

Whichever mode you fly, you will want the on-screen radio to match. Select Radio
Mode (gadget only) to show the list of available radio modes. Click the mode that is
appropriate for you.

Arrange
This menu item allows you to organize the on-screen viewports. This is especially
helpful when there are multiple windows open that overlap one another.

256

Click on the Window menu followed by the Arrange menu item to activate this
option.

Close All
This menu item closes all open Windows with the exception of the main Window. It
offers the user an easy method to clean up the screen without having to close each
window separately.

257

To access the Close All menu item, click on the Window menu followed by the Close
All menu item.

Viewport List
As you add more viewports to the screen, note that they appear on a list in the
Window menu title. If you wish to change the active view to one of these viewports,
simply click on the viewport name in the list.

258

To determine the active window, simply search for the yellow outline that surrounds
the active window. In the example above, the active window is the Viewport.
To change the active window, click on, or in, the window that you wish to become
active.

259

14
Chapter

Help Menu
When all else fails, ask for help.

his menu provides you with miscellaneous assistance and guidance with a
variety of simulator-related issues.
To access the Help files, click on the Help menu title.

The menu items available under the Help menu are:

Contents

261

Keyboard Commands

About

License

Websites

Contents
This menu item accesses RealFlight G4s manual which you are reading now.

To access the Contents files, click on the Help menu title.

262

Keyboard Commands
RealFlight allows you to access menu and other commands from your computers
keyboard. A key that directly invokes a command is called a quick key or hot key.
For example, pressing the [+] (plus) key on the keyboards number pad incrementally
zooms your view towards the aircraft. This is exactly the same result that arises if you
select Zoom In from G4s View menu item. Consequently, we say that the [+] (plus) is
a hot key for the Zoom In command.

To access the Keyboard Commands, click the Help menu title, followed by the
Keyboard Commands menu item.
Alternatively, you may also bring up the Keyboard Commands by pressing the
keyboards H key.
The following overlay will appear:

263

The Keyboard Commands screen contains all of the information pertaining to the hot
keys. To view the entire list, drag the scroll bar on the right side of the Keyboard
Commands screen down. Alternatively, this list is also contained in the inside rear
cover of the Installation Guide which accompanied this software.
If you do not wish to view this information, double-click on the title bar of the display
box. This will hide the information. To view it once again, simply double-click the
title bar.
Clicking on the X in the title tab of the frame will remove it from the screen.

About
The About menu item contains miscellaneous information pertaining to your
software. The About menu contains your RealFlight serial number, InterLink Elite
serial number and the version number of the software that you are currently operating.

264

Also seen in the About screen are the credits and names of the people that have
worked together to bring you the worlds most realistic R/C simulator, RealFlight
Generation 4.
Clicking on the X in the title tab of the frame or clicking anywhere on the main
simulator screen will remove the About window.

License
This menu item contains the End Users License Agreement (EULA) for the RealFlight
R/C Flight Simulator. Please read it carefully.

265

Clicking on the X in the title tab of the frame will remove it from the screen.

Websites
This menu item contains links to the RealFlight related websites. The options include:

266

Great Planes-

Publishers of RealFlight G4. Visit this site for information pertaining to the many
other Great Planes products available.
Knife Edge Software-

Developers of RealFlight G4. Visit the Knife Edge forums to share experiences and
technical support with other RealFlight owners. The Knife Edge forums also play host
to a wide variety of free, downloadable aircraft, trim schemes, flying sites and more.
RealFlight-

Visit the RealFlight website for more information about the RealFlight family of
products, search the knowledge base for technical support, or for information on how
to contact our support staff if you have questions.

267

Appendix

Basics of Flying
Understanding the fundamentals of radio control flying.

efore taking control of a transmitter, it helps to understand the basics of flight,

and the functionality of the gimbals, sticks and switches to properly control
the aircraft. This chapter reviews the basics of flying an airplane or a
helicopter to help get you started down the right path.

Airplane Basics
Before you fly the plane, make sure all switches are in their off or low rates, positions.
The switches may be assigned to different items depending on how you have
configured your controller and which aircraft you are flying. If you are using your own
transmitter to control RealFlight, please consult your transmitter owners manual for
more information.
The InterLink Elite features digital trim tabs which are more precise and offer trim
memory within the simulation. Trim tabs are the small slider controls on the controller
(two per controller stick). They trim the aircraft so that it flies straight and level. For
example, if an airplane has a tendency to veer slightly downward, you may need to add
a slight up nudge to the elevator. You can do this by sliding the elevator trim, a click
or two at a time, towards the bottom of the controller.
Crashing-

Takeoffs are optional, but landings are mandatory. For any type of aircraft or flying,
successfully landing an aircraft is a crucial skill to master.
The key to a perfect landing is undivided concentration. Pay close attention to the
altitude, orientation, and speed of the aircraft as it approaches the runway. Should you
happen to crash, use each crash as a learning experience to perfect your approach and
the landing.

269

RealFlight has several tools to help you stay on top of things during approach and
landing. See the Landings section below for some ideas.
Out at the field a crash might result in one or more of the following:

Bruise your ego

End flying for the day

Cost you money

Cost you time to rebuild

Cause injury to yourself or a bystander

Even win you a nice best crash trophy!

Of course, when you crash on the simulator, there is really no harm done. None, that
is, except the bad habits you may acquire. We suggest that you take the crashes
seriously and learn from each one. By doing so, you will be a better pilot out at the
field.
Airplane Flight-

RealFlight G4 accurately simulates how R/C aircraft really fly. This allows you to
practice R/C flight without worrying about expensive crashes. Additionally, RealFlight
G4 is ideal for practicing new maneuvers and experimenting with various parameter
adjustments.
It is important to remember, however, that a simulator will only help you learn to fly if
you let it. Otherwise, it is just a game. Learning to fly R/C aircraft requires a
commitment. One does not just grab the sticks and start dazzling the crowds. A
methodical, patient approach will help you get the most out of this simulator.
This section is not designed to teach you how to fly. However, it will help you enhance
your experience with the simulator and obtain the most from your experiences.
Takeoffs-

When you are taking off, start with the throttle in low position and slowly
increase throttle by pushing the throttle stick away from you towards the top
of the transmitter until you are at about half speed. Stay in the middle of the
runway (you can steer the plane using the rudder). When you have built up
enough speed, gradually pull back on the elevator stick to climb off the
runway. If the plane is tracking well, apply the rest of the power more quickly,
climb out, and gain altitude.
Be careful not to veer off the runway. In a real plane, chances are that you
would crash (or get stopped on the grass). Usually this means bent landing

270

gear and a broken prop. If your plane has retracts, they could even be torn out
of the wing.
For the best practice, its recommended that you utilized the Takeoff Trainer
available with RealFlight G4. For more information, see the Takeoff Trainer
section on page 202.
Landings-

It is very important to land on the runway, rather than veering off, or touching
down before you reach the runway. Either of the latter usually produces a
moderately expensive crash. If you cartwheel (wing tip hits the ground first),
the wing can break, resulting in lengthy down time while you repair your
airplane.
Start by aligning your plane parallel with the runway. Fly the approach
normally, using your throttle to control the rate of descent. Try to land at the
slowest speed possible. If your plane has flaps, use them to kill speed (but be
careful; with flaps down your plane will try to pitch up and climb). If your
plane has retractable landing gear, lower them. As you touch down, remember
to keep your nose up!
RealFlight has several tools to help you practice landings.

Before you try to land yourself, you may want to get a lesson from a pro.
To do so, click the Training menu followed by the Virtual Flight
Instruction menu item. Choose Jason Shulman as the instructor.
From the list of options, select the Landing maneuver.

Gain experience through the Landing Trainer. It offers guidance and

helps set you up for the perfect landing. See the Landing Trainer on page
207 for more information.

During your approach, use the NavGuides to keep track of your speed,
altitude, and distance above ground.

Aerobatics-

When you practice aerobatics, the three important steps are:

Start the plane straight and level, in a controlled situation

Perform the maneuver

Return to a straight, controlled situation

271

Anyone can give it full throttle, jam the sticks in all directions and watch the
plane tumble and roll. However, this is not what you will do out in the field.
Do this and you will not have control of the airplane!
The key to properly performing the maneuver is in the setup. Doing so will
allow you to cleanly finish and your experience will be more rewarding as well
as more realistic.
Concentrate on making the maneuvers clean and crisp. If you are doing a
roll, try to keep the plane on a straight line as you roll. If you are doing a loop,
try to make a perfectly round circle.
If you want to practice aerobatics using RealFlight G4, try the Virtual Flight
Instruction feature (accessible via the Training menu). The Virtual Flight
Instruction feature provides a series of personal lessons taught by pros.
Throttle Management-

Avoid the temptation of giving the plane full throttle and keeping it there for
hours at a time. This teaches you bad habits and makes even a good flier look
like a rookie out at the field.
Many of the maneuvers require proper throttle management in order to make
a maneuver look good. Loops, stalls, torque rolls, touch-and-goes are just a
few examples. Try doing various maneuvers at differing speeds. Try
performing a slow roll at medium throttle and keeping a perfectly straight line.
This difficult maneuver will earn you more praise at the field than doing a full
speed, full stick roll.
Rudder Management-

Most airplanes can (more or less) be effectively flown with just the elevator and
ailerons. Good pilots will tell you that the proper use of the rudder is just as
important, however. Many aerobatic maneuvers require excellent rudder
usage.
Rudder control is especially important when landing in a crosswind. Pilots that
cannot use the rudder usually land in the tall grass (embarrassing!). Pilots that
do use the rudder can land on the numbers almost every time.

Helicopter Basics
A model helicopter is a very complicated machine, which operates on the same
aerodynamic principles as its full-scale counterpart. These principles are quite
complicated to explain and understand. However, it is not necessary to understand all

272

the underlying aerodynamics in order to successfully fly a model helicopter (or a

computer simulation).
The following will help you to better understand the basics of helicopter flight, and the
relationship between control stick movements and the actions of the machine. Refer to
these instructions often as you become more proficient.
Please note: the inputs below are shown using a Mode 2 transmitter.
Collective (Left Stick Vertical Movement)-

The spinning main rotor blades, which act like rotating wings, lift the helicopter into
the air. Changing the pitch (angle of attack) and speed of the blades, using the
collective and throttle causes the helicopter to rise and descend vertically. Adjusting
collective increases and decreases the blade pitch. The throttle control increases
and decreases engine RPM. On a model helicopter, the collective and throttle controls
are mixed electronically, and controlled by the throttle stick on the transmitter or
controller.

273

Rudder (Left Stick Horizontal Movement)-

To turn the nose of the helicopter left or right, change the tail rotor pitch (by using the
rudder control). Changes in collective stick movement will require changes in the
amount of rudder input to maintain the desired heading.

274

Cyclic Stick (Right Stick)-

The cyclic stick replaces the aileron and elevator controls found on a fixed-wing
aircraft. Cyclic is the term given to the control of the main rotor that allows the
helicopter to fly forward, backward, left and right. Forward cyclic stick movement
causes the helicopter to pitch forward, left cyclic causes the helicopter to tilt sideways
to the left, on so on. You move the helicopter forward or sideways using a coordinated
movement of both the cyclic and collective control sticks. Moving the cyclic stick to
the right, while simultaneously increasing collective, will cause the helicopter to move
sideways to the right. Rudder control is used to maintain the heading.

275

276

Idle-Up-

A switch on the controller actuates a special function, known as idle-up. Idle-up

offers an alternate throttle and pitch curve, different from the curves used for hovering.
Idle-up is usually used for aerobatics, when the pilot wants engine power added when
pitch is subtracted. For example, inverted hovering requires positive throttle and
negative pitch. As such, pulling the collective stick back provides positive throttle
AND increased pitch simultaneously.
Throttle Hold-

Another special function is known as the throttle hold. When activated, this switch
sets your throttle to idle but allows the collective to function normally. This allows you
to practice autorotations without shutting the engine off.
Gyro-

Any sudden change to the torque of the main rotor, such as a quick change in RPM or
a wind gust, can cause the helicopter to turn unintentionally to an unwanted direction.
An electronic device known as a gyroscope (gyro) is used to monitor and correct for
this by giving commands to the rudder control to help stabilize the machine.
Gyros come in a variety of types, each with different features. A normal gyro will not
return the helicopter to its former heading; it will simply dampen the unwanted sudden
movement. We recommend you start by using the heading hold gyro instead; it will
maintain course and keep the nose of the helicopter pointed in the desired direction
regardless of outside forces.

277

Helicopter Flight
Hovering-

The machine hovers by adjusting the collective/throttle control to maintain altitude,

the rudder to maintain heading, and minute adjustments to the cyclic controls to
maintain location. Hovering is the most important aspect of helicopter flight to
master, since every other movement of the machine begins and ends with a hover.
Forward Flight-

The helicopter moves forward by changing cyclic (moving the cyclic control forward).
This causes the rotor head, and thus the helicopter to tilt forward, resulting in a
forward thrust. As the cyclic increases, the collective must also be increased to maintain
the desired flight path. As forward speed increases, the collective can be reduced
slightly.
Backward Flight-

Backward flight is accomplished by moving the cyclic control aft, which causes the
rotor head, and thus the helicopter to tilt backward. As the cyclic is moved aft, the
collective must also be increased to maintain desired flight path. As backward speed
increases, the collective can be reduced slightly.
Sideways Flight-

Moving the cyclic control left will cause the rotor head, and thus the helicopter to tilt
left. Add collective and left rudder to cause the helicopter to slide sideways to the
left. As speed increases, it will require progressively more rudder to maintain heading.
To move right, simply follow the same procedure, but reverse the cyclic and rudder
movements (move cyclic right, apply right rudder).
TurningFrom forward flight-

Moving the cyclic control left, while applying a small amount of aft cyclic and
feeding in left rudder, will cause the helicopter to make a coordinated turn to
the left. Right movement of the cyclic and rudder sticks will cause the heli to
turn to the right.
From a hover-

Use the rudder to rotate the nose of the helicopter in the direction you want.
Learning to fly a model helicopter is more difficult and challenging than any
other genre of radio control modeling, but is also the most rewarding as you
master the techniques required for sustained hover and forward flight.
Computer simulation of model helicopter flight is an excellent tool for learning
the basics and dramatically reducing the learning curve when you move on to
the actual model itself.

278

Appendix

RealFlight G4 Launcher
The RealFlight G4 Launcher is the gateway to simulator fun!

his item allows you to run the simulation, register and update the software, and
much, much more.

To run RealFlight or to access the additional options, click the RealFlight G4

Launcher located on your desktop.

279

Run RealFlight
To start running RealFlight, press the RealFlight G4 Launcher located on your
desktop. Next, click the Run RealFlight button. The simulation will begin loading
the terrain, airport objects, textures, etc. Your simulation experience will begin as soon
as the loading process completes.

Additional Options
Click on the Additional Options button to access a variety of useful information
pertaining to RealFlight G4.

280

Restore Defaults-

Use this button to restore RealFlight G4s default settings. Doing so will NOT remove
custom aircraft, flying sites, etc. Rather, it is designed to simply restore the factory
default values and settings for the simulation.
Registration/Updates-

Use this button to register and update the software.

281

Online Registration-

This button allows you to register your copy of RealFlight G4. The
registration information entitles you to complimentary technical support and
free online updates.
Please enter in all of the required information to complete the registration. If
you forget your password, contact Great Planes Support. To do so, email
them at [email protected] or telephone them at 217-398-8970
(option #1). They will confirm your identity, and reset your password.
Hardware Information-

RealFlight G4 offers the option of automatically sending us

information pertaining to your system hardware and settings when you
register. If you leave the Send Hardware Information box checked
when you register, RealFlight G4 will send us this information.

282

This hardware information will assist us in diagnosing any problems

you may encounter later, should you need to contact Technical
Support Consequently, we suggest that you leave this box checked
when registering.
This feature is optional. If you uncheck the box, RealFlight G4 will
not send us any information about your system. Alternatively, you can
view exactly what information RealFlight will send us before you
decide. To view the information, click the Technical Support
button. When the Technical Support page appears, click Assemble
System Information.
Update to Latest Version-

After registering (you only need to register once), you may update to the latest
version of the software. This will download all necessary files and correctly
install the upgrade.
Click this button to Update to Latest Version.
Please note: your PC must be connected to the Internet in order to check for
updates.
Check for Updates Before Starting RealFlight-

If you check this box, every time you run the RealFlight G4 software it will
check to determine whether or not there is a more recent version of RealFlight
G4 available to you. If a new version exists, RealFlight G4 will ask if you wish
to download and install the newer build.
Please note: your PC must be connected to the Internet in order to check for
updates.
Update to Specific Version-

If you are experiencing difficulties with a version you have installed, this will
allow you to retrieve a previous version of the software. If the previous
version fixes your problem, please contact our technical support team at
[email protected] and let them know about the difficulty
encountered.
Clear Download Cache-

Occasionally, files may become corrupt during a download. If you are having
difficulties with the online updates, remove all cached files using this option.
Next, choose Update to Specific Version and then select the Completely
Refresh option.

283

Uninstalling RealFlight-

Click the Uninstall RealFlight button to uninstall the software. The following dialog
will appear:

We suggest that you use this method, not the Add/Remove Programs feature in
Windows, to uninstall RealFlight G4. The RealFlight G4 launcher will remove all
necessary RealFlight G4 files.
Uninstall Program-

Choose this option to uninstall only the RealFlight G4 program itself.

Uninstall Data Files-

Choose this option to uninstall any user files such as customized airports,
customized aircraft, color schemes, songs etc. Be careful with this option! You
could lose a lot of your work by inadvertently uninstalling these files.
Remove Serial Numbers-

Choose this option to remove the serial numbers from your system. You have
two options available if you check this box.

For this product only

For all RealFlight products, including Expansion Packs, older RealFlight

editions, and Add-Ons

Remove All Cached Files From The Online Update-

Choose this to option to remove all cached download files from your system.
If you uninstall these files, future downloads may take a little longer.

284

View Web Site-

Click the View Web Site to visit the RealFlight web site. A browser window will open
for you and you will be automatically directed to the site.
Please note: your PC must be connected to the internet in order to view the RealFlight
web site.
Read Help File

Press the Read Help File button to bring up the manual, this document that you are
reading now, file for RealFlight G4.
Technical Support-

Press the Technical Support button to bring up technical support information

pertaining to your system. If you encounter any difficulties with RealFlight, this
information can help you to resolve the situation on your own, or may assist Great
Planes Support Staff to diagnose the problem.

System Information

This displays a list of the critical system information. Before you email
technical support, or report a bug with the software, please be sure to cut and

285

paste this information into your email.

diagnosing the difficulty.

This will greatly assist them in

Reinstall DirectX

Choose this option to reinstall DirectX. Occasionally this will fix corrupted
installations.
Enter Technical Support Code

Choose this option to enter a technical support code. If you do encounter

problems running RealFlight, our Technical Support team may supply you
with a code to input here. Entering this code will help them diagnose or
resolve your difficulty.

Email Technical Support

This gives you the email address [email protected] to which you can
email your difficulties. If you do email us, please be sure to attach the
Assemble System Information output to your email.
You will receive an auto-reply message back confirming that Great Planes
Support Staff received your email. If you do not receive the auto-reply
message, please double-check that you sent your email to the correct email
address.
Assemble System Information

Choose this option to collect critical information about your system, and about
your RealFlight settings. You may find this information useful if you try to
troubleshoot problems on your own. Moreover, if needed you can cut and
paste this information into an email to Great Planes Support Staff.

286

View Web Technical Support-

Choosing this option will open a browser window, and take you to a web site
that contains the most up-to-date technical support information for RealFlight
G4.
View Tasks-

This shows you a list of all tasks that are running on your computer. Some
tasks can interfere with RealFlight G4 and may need to be closed.
Include Serial Numbers-

Check this box if you plan to assemble all system information to send to Great
Planes Support Staff. If you are sending this information to anyone else, dont
check this box. The serial numbers are unique to you, and should only be
shared with Great Planes Support Staff.

287

DX Diagnostics-

This brings up Microsofts DXDIAG utility. Using this utility can further help
diagnose your system.
Important: if you send us information about your system to help us diagnose a
problem, please do not use DXDIAG to generate that information. Instead,
please use the Assemble System Information. The Assemble System
Information output file contains more information than the DXDIAG
output.
MSInfo-

This option will run MSInfo. This will give you even more information about
your system. This program is not always installed on a particular computer,
but normally comes with programs such as Microsoft Office.
Display Properties-

This brings up the display properties for your monitor. You can use this page
to change the resolution of your desktop.
Explorer-

This button launches Windows Explorer. This Microsoft Windows utility can
help you locate, move and back up your files.
Launch Device Manager-

This button launches the Device Manager. This Microsoft Windows utility
will help you determine driver dates, as well as installing and updating video
and sound card drivers.

288

Appendix

If You Experience
Difficulties
Tips and tricks for solving the more common problems.

he RealFlight G4 simulator is on the cutting edge of technology, and therefore

operates using advanced hardware. Consequently, there is always the remote
possibility you may experience a few slight difficulties. Should the need arise,
we provide extensive resources to help.

Besides providing the best R/C simulator, we sincerely feel that we provide the best,
most extensive product support for any R/C simulator. Since cards, drivers, and
operating systems are always changing, we work hard to keep our support team up-todate on the latest information available to ensure that you have the most enjoyable
experience possible.
This section begins with a summary of the various sources of RealFlight G4
information including support and problem solving assistance. Then, we will show
you some simple but powerful steps that can resolve or prevent most RealFlight G4
difficulties. Finally, if these steps fail to solve your difficulty, we will explain the most
effective ways to acquire additional assistance.

How to Get Help and Information

As a RealFlight G4 user, you have access to an incredible amount of information about
this product. Much of this information can help you resolve difficulties, or correctly
access and use program features. Here is where you can find it:

The manual. Most common RealFlight difficulties can be resolved by following

the instructions in later sections of this chapter. However, there is also additional
information throughout other chapters that may be of assistance.

289

Visit our product Knowledge Base at http://www.gpsoftware.com. This is a great

resource and is an indexed, searchable collection of articles that describe solutions
to almost every known situation with RealFlight, RealRace, and all of our other
software products. In fact, this is the same information database used by our
product support technicians.

Visit the Knife Edge Software Message Boards at

http://www.knifeedge.com/forums/. This is a place where owners of RealFlight,
RealRace, and other Knife Edge products post questions, comments and
responses. Sometimes our product support technicians and product developers
from Knife Edge post replies and announcements as well. You may find a thread
that discusses the same difficulties that you are experiencing.

Contact our Technical Support department by email at:

[email protected]. Alternatively, our staff is also available via telephone
or postal mail at:
RealFlight Technical Support
3002 North Apollo Drive
Suite #1
Champaign, IL 61822
Voice phone:
(217) 398-8970(Option 1)
FAX:
(217) 398-7721
The product support teams are specially trained, and have many resources to help
you resolve problems with RealFlight G4.

Before You Do Anything Else

If you are experiencing difficulties with RealFlight G4, you should always try the steps
below first. These steps really do cure most problems our users experience. Even if
you are not having a problem, these same steps often assist in the operation of both
RealFlight and your computer.
Here are the steps you should take (instructions for each step follow):

Update your video and sound card drivers (see instructions below).

Update to the latest version of RealFlight G4.

If the problem persists, run the DirectX test programs.

If these steps do not work, proceed to the next section.

290

Update Your Drivers-

Before you do anything else, you should make sure you have updated your video and
sound drivers. A large number of difficulties encountered by RealFlight users can be
cured by updating drivers.
A driver is a software program that controls your video or sound card. Each card
manufacturer provides drivers for its own cards. To work correctly, RealFlight relies
on your video and sound card drivers.
It is very important to use the latest available driver for your card. Card manufacturers
frequently release updated drivers to fix problems that occur when the driver is used
with programs such as RealFlight G4. The driver that came with your new computer,
on your Windows CD-ROM, or on a CD-ROM included with the new card you
bought, may not be the latest version.
If you do not know how to update drivers, you can find instructions in our Knowledge
Base article Q01-1038, How to Update Drivers, at http://www.gpsoftware.com/kb/q011038.htm. This page will take you through the process step-by-step, and has links to
driver download sites for most manufacturers.
Update to the Latest Version of RealFlight G4-

As we regularly release program updates, the difficulty that you are seeing may already
be fixed in an update. Even if you just bought RealFlight, you should update to the
latest version. Its free and only requires a few minutes of your time.
Run the DirectX Test Programs-

If you have updated your drivers and RealFlight to the latest versions, and your
problem persists, you should try to run the DirectX samples that come with RealFlight.
The DirectX samples (DirectDraw, Direct3D, Sound, etc.) are test programs written by
Microsoft. These samples ship with DirectX, and are designed to check whether your
DirectX installation, video/sound cards and drivers, etc., are working correctly. They
should work on any DirectX 9 compliant driver.
These samples are found in the Technical Support area of the software. Click the
Technical Support button followed by the DX Diagnostics button. Next, click either
the Sound or the Music tabs, then the Test DirectX Music/Sound buttons. Once
these tests have been completed, press the Display tab to access the Test DirectDraw
and TestDirect3D buttons.
The most important tests are DirectDraw and Direct3D, both of which test your video
card and driver. If you are having any graphics difficulty in RealFlight G4 (including
RealFlight G4 freezing your system so that you have to reboot), look for the same
problem in these tests. If the problem occurs only after you have run RealFlight G4
for a long time, make sure to run the tests for a comparable length of time.

291

If your RealFlight G4 problem also occurs in Billboard, the problem lies with your
video driver, not RealFlight G4. To resolve the problem, try finding updated drivers
for your card (see above). If the problem still occurs with the latest drivers, you will
need to report this problem to the card manufacturer. Be sure to tell them that you
tested the card by using Billboard. Please note: in rare cases, a newer video driver may
have more problems than a previous version. After exhausting all other options, you
might try obtaining an older driver from the manufacturer to eliminate this possible
cause as well.

If You Need Additional Assistance

If you have updated drivers and updated RealFlight G4, your system successfully runs
the DirectX sample programs, and you are still having problems. What next?
As a first step, we suggest checking our Knowledge Base at
http://www.gpsoftware.com. This is an easy to use, searchable, browsable database of
known problems and solutions for RealFlight, RealRace, and our other software
products. This is the same database that our Product Support technicians use when
helping customers. We constantly update the knowledge base to address new
problems as we discover them. In many cases, you will be able to find an article that
gives clear, concise instructions for resolving your difficulty.
You may also want to check the Knife Edge Message Boards at
http://www.knifeedge.com/forums/. This is a place where owners of RealFlight,
RealRace, and other Knife Edge products post questions, comments and responses
about problems. You may find a discussion thread about the problem you are
experiencing.
You can also contact Technical Support at Great Planes via email at:
[email protected].
IMPORTANT. If you do contact Technical Support, you can help us enormously by
providing detailed information about your computer system. Since your problem may
only occur on a particular video or sound card, particular driver version, etc., we may
need this information to help us diagnose your problem. To compile your system
information, use the RealFlight G4 Launcher. Click the Additional Options
button. Next, click the Technical Support button, followed by the Assemble
System Information button. This will create a file called c:\launcheroutput.txt,
which contains your system information. Attach this file to an email and send it to us
at [email protected].

292

Examples of Common Problems and Solutions

If You Dont See Your Problem in This Chapter-

This chapter contains a few examples of common difficulties and concerns that
RealFlight users have experienced.
Remember that we can never provide a complete list of difficulties and solutions in a
program manual. Thats because RealFlight--and the computers, cards and drivers it
uses--are constantly evolving. As such, we maintain a detailed Knowledge Base at
http://www.gpsoftware.com. By keeping our Knowledge Base online, we can provide
you with the latest information about resolving any difficulties that might arise. If you
dont see your difficulty described in this chapter, please check the Knowledge Base.
In this chapter, weve simply tried to pick a very short list of the most asked about
issues.
My computer freezes when I run RealFlight-

Sometimes, you may also notice sound skipping or repeating, or a computer reboot
while flying. To resolve this type of problem, you must update the drivers for your
video and sound cards. This is very important. Card manufacturers regularly update
their drivers to fix this type of problem. Even the driver that came with your new
computer may not be the most recent.
Sometimes a card manufacturer will offer a choice between a recommended driver,
and another driver (variously called special purpose, alternate, or beta driver). If
RealFlight G4 freezes with the recommended driver, try using the alternate driver
instead.
If you are sure that you are using the latest drivers, and have followed all the other
steps in the previous section (update RealFlight G4, test DirectX) and are still having
difficulty with your computer locking up while running RealFlight, please contact Great
Planes Technical Support.
Improving RealFlight G4 Performance-

During installation, RealFlight G4 analyzes your computers hardware specifications.

RealFlight G4 then tries to optimize its configuration to best take advantage of that
hardware, and achieve the best possible performance.
However, if the performance is less than you desire, you can adjust some of RealFlight
G4s settings to improve the simulation speed and frame rate:

Ensure that the drivers for the video and sound cards are up-to-date.

Turn off all other programs, especially virus checkers and network applications
(such as Instant Messengers) while running RealFlight G4. Use CTRL-ALT-

293

DELETE and check the Task Manager to verify that nothing else is running in
the background.

Reduce the texture and water quality. This can have a profound effect on cards
that do not have a high texture memory. See the Settings section starting on page
76 for more information.

Eliminate the items shown in the simulation. To do so, access the View menu
title, then access the Show menu item. Click an item type to remove it from the
simulation. It may be necessary to eliminate several items before performance
meets your expectations.

Reduce the number of open Gadgets and Viewports. Click the X on each Gadget
or Viewport that you wish to close.

Reduce the number of recordings currently in use.

Other Common Problems-

Here are some other things you may want watch for.

Check the CD-ROM for scratches or blemishes. Even minor scratches or

fingerprints can cause random problems that appear to be program bugs.

Make sure your hard drive has at least 500 MB of space available. To check this:
1. Double click on the My Computer icon on your desktop
2. Right click on your main hard drive (usually drive C:\)
3. When the popup menu appears, select Properties
4. In the dialog that appears, view the amount of space available on the drive
If you need additional space, try emptying the Recycle Bin.

Verify that all other programs are closed prior to starting RealFlight G4. RealFlight
works best when it is the only program running.

If all else fails, try rebooting your computer. Occasionally, Windows (particularly
98 and ME) may become unstable after prolonged and continuous use. A simple
reboot may clear up any difficulties.

294

Glossary
180-Degree Turn
R/C Term

360-Degree Turn
R/C Term

3D Acceleration
Computer Term

ATV
R/C Term

AccuModel
RealFlight Term

Active View
RealFlight Term

Advanced Flight Recorder

(AFR)
RealFlight Term

This basic flight practice starts with a takeoff, and

then demonstrates 180 degree turns on a flight path
parallel to the runway.
In this practice, you will learn to fly the aircraft in a
complete circle (360-degree turn). This maneuver is
a great way to learn control inputs for turns while
keeping the same radius and altitude.
3D operations require a huge number of
calculations. Modern computers offload many of
these calculations to the video card, rather than
performing the calculations directly on your
computer's CPU. This speeds up the simulation
and allows for faster frame rates, thereby increasing
the realism of the simulation.
Amount of servo travel. For instance, 50% ATV
would mean the servo's maximum travel is 50% of
its physical limit.
RealFlight G4s AccuModel aircraft editor offers the
most powerful, most flexible aircraft editor ever
released in an R/C simulator.
The active view is the view that is affected by the
commands in the View menu. Only one view at a
time is active. You can make a view active by
clicking on it with the mouse. When you want to
control a views properties, you must first make it
the active view.
This feature allows the pilot to not only view
prerecorded maneuvers, but also allows them to
record their own.
During the playback of
maneuvers, the pilot has the ability to select from a
number of different options such as fast forwarding,
rewinding, looping, speeding up and slowing down
the recordings. These recordings may also be sent
to others via the Internet. The pilot can also
activate an on-screen transmitter to watch the stick
inputs for each pre-recorded maneuver.

295

Adverse Yaw
R/C Term

Aileron
R/C Term

Airfoil
R/C Term

Airframe
RealFlight Term

Angle of Attack
R/C Term

Arm
R/C Term

Auto-Play
Computer Term

The tendency of an airplane to yaw in the opposite

direction of the roll. For instance, when right aileron
is applied, the airplane yaws to the left, thus
opposing the turn. Adverse yaw is common in
trainer type airplanes having flat bottom wings. It is
most noticeable at slow speeds and high angles of
attack, such as during takeoffs and when stretching
a landing approach. Caused by the unequal drag of
the upward and downward deflection of the
ailerons, this undesirable trait can be minimized by
setting up the ailerons with Differential Throw or
by coordinating the turns, using the aileron and
rudder controls simultaneously.
Hinged control surfaces located on the trailing edge
of the wing, one on each side, used to provide
control of the airplane about the roll axis. The
control direction is often confusing to first time
modelers. For a right roll or turn, the right hand
aileron moves upward and the left hand aileron
moves downward. The movements are reversed
for a left roll or turn.
A surface (such as a wing or propeller blade) with a
shape and orientation such that it provides or
controls stability, direction, lift, or propulsion.
A term used to describe the general components of
an aircraft when using RealFlight G4s AccuModel
aircraft editor. For example, selecting the airframe
will call up the fuselage, wing(s) and tail of an
airplane.
The angle that the wing penetrates the air. As the
angle of attack increases so does lift and drag, up to
a point.
In this context, the arm is the distance from the
point of the application of a force to the axis of
rotation. If you press down on the tip of a wing, for
example, the arm is the distance from the point
where you are pressing to the root of the wing.
A Windows feature that automatically detects when
a CD-ROM is inserted and runs the specified
program on the CD-ROM.

296

Autorotation
R/C Term

Autorotation Event
RealFlight Term

Avalanche
R/C Term

Bloom Effect
RealFlight Term

Channel Mapping
RealFlight Term

Chat
RealFlight Term

Child/Children Item(s)
RealFlight Term

Chord
R/C Term

CG
R/C Term

A maneuver in which the pilot attempts to bring the

helicopter in for a landing without power from the
engine. The momentum of the spinning rotor
blades is enough to slow the helicopter prior to
landing.
An event where players attempt to autorotate onto a
target (similar to Spot Landing). Each player takes a
turn. Players collect different point amounts based
on landing location. The Autorotation Event works
for helicopters only. The Deadstick Event is for
airplanes.
The Avalanche is a loop with a snap roll at the top
of the loop. This snap roll must be centered at the
top of the loop.
The effect creates a feathering of light around
brighter objects, giving it a more realistic look. This
is more noticeable at brightly lit airports around
aircraft that are lighter in color.
This term describes the ability of RealFlight G4 to
alter the mapping or input of the servos to
accurately reflect the actual controls from an R/C
controller.
This is a real-time communication between two G4
users which is conducted via the PC. G4s
multiplayer feature enables a public chat if so
desired.
In many of RealFlight G4s selection windows,
items are displayed in a hierarchy format. An item
that belongs to a higher group, or parent, is
considered the child item.
The chord of a wing or surface is the width of the
surface. A wider chord offers increased lift.
However, a wider chord also generates more drag
when the aircraft rolls.
CG is the abbreviation for the phrase Center Of
Gravity. This is the point at which the aircraft
balances fore to aft and side-to-side. The location
of this point is crucial to how the aircraft reacts in
the air. For airplanes, a tail-heavy plane will be very

297

snappy, but generally unstable and susceptible to

frequent stalls. Conversely, a nose-heavy plane will
tend to track better and be less sensitive to control
inputs, but will generally drop its nose when the
throttle is reduced to idle. This makes the plane
more difficult to land, since it takes more effort to
hold the nose up. A nose heavy airplane will have
to come in faster to land safely.
Collective
R/C Term

Collision Detection
RealFlight Term

Coning
R/C Term

Control Surface
R/C Term

Controller
RealFlight Term

Cuban Eight
R/C Term

Cyclic
R/C Term

A mechanism on a helicopter that changes the pitch

of the main blades, thereby allowing the helicopter
to ascend or descend accordingly. This is the
control that adjusts the pitch of the rotor blades.
RealFlight G4 sports the most advanced collision
detection modeling ever used in an R/C model
simulation. It blankets the entire aircraft, ensuring
accurate modeling of the aircraft when it collides
with objects and items within the simulation.
When a helicopter hovers, the blades form a slight
"cone" when viewed from the side. The Coning
effect is caused by the balance between lift and
centrifugal forces on the blades.
Generally defined as the portion of the airfoil that
moves.
Examples include ailerons, elevators,
rudders, flaps, and spoilers.
A device used to control an aircraft in RealFlight.
G4 ships with the Great Planes USB InterLink
Elite Controller by Futaba. This device can be used
as a standalone controller, or as an interface to use
your own R/C transmitter. Previous versions of
RealFlight shipped with either a Futaba game port
controller or a Transmitter Adapter Interface. For
information on the latter two controllers, please see
the manuals that came on the program CD with
those versions of RealFlight.
This maneuver requires that the pilot perform a half
roll on each of the descending forty-five degree
down lines, allowing the pilot to fly a horizontal
figure eight without performing an outside loop.
Refers to the changing of a main rotor blade's pitch
as the rotor head rotates. Pitch is added while the
blade is pointing in one direction (e.g. while the

298

blade is over the canopy), and removed while the

blade is pointing the opposite direction (e.g. while
the blade is over the tail boom). This causes the
helicopter to pitch and roll.
Data Lever
RealFlight Term

Deadstick
R/C Term

Deadstick Landing Event

RealFlight Term

Dihedral
R/C Term

Direct Control Interface

RealFlight Term

Direct3D Technology
Computer Term

DirectX
Computer Term

Dithering
R/C Term

Down Thrust
R/C Term

RealFlight G4s InterLink Elite has the ability to

make on-screen selections, or quickly look at the
windsock or ground. This can be done with the
Data Lever, located at the bottom right-hand corner
of the InterLink Elite controller.
A term used to describe unpowered flight (glide)
when the engine ceases operation.
See Autorotation Event. The Deadstick Landing
Event is specific to airplanes.
The V-shaped bend in a wing. Increasing the
dihedral usually enhances the aerodynamic stability
of an airplane, and causes the rudder to control
both the roll and yaw axis. This is why some
trainers and sailplanes require only three channels of
radio control (i.e., they have no ailerons).
This is a method for using your own radio to
completely control the aircraft. This usually means
you have a separate radio program on your radio for
each aircraft that you want to fly in RealFlight G4
with this method. All mixing and radio functions
are performed on your radio and RealFlight simply
passes the values directly to the aircraft servos. This
is in contrast to the Joystick Emulation Interface.
A Microsoft DirectX technology used to render the
3D image when you have a graphics accelerator
card. It works best on faster computers.
A technology created by Microsoft that controls
graphics and sound operations.
A method of removing and/or simulating colors
that may not be available to the graphics processing
unit.
This is the downward angle of the engine in
relationship to the centerline of the airplane. Down
Thrust helps overcome the normal climbing

299

tendency of flat bottom wings.

Driver
Computer Term

Edit NavGuides
RealFlight Term

Elevator (Maneuver)
R/C Term

Elevator (Control Surface)

R/C Term

Endpoint Adjustment
R/C Term

Event
RealFlight Term

A software program that controls a card (e.g., video

or sound card) in your computer.
Card
manufacturers usually provide drivers as well. Card
manufacturers frequently update their drivers to fix
bugs or to make their cards compatible with new
software and hardware. You can often find an
updated driver for your video or sound card by
visiting the card manufacturers web site and
following links to Drivers, Support,
Downloads, or Upgrades.
A NavGuide is a gadget that displays continuously
updated information about your aircraft. The Edit
NavGuides dialog is used to customize the
NavGuides gadgets.
The Elevator is a maneuver in which the aircraft is
made to stall completely with a large amount of
elevator throw. The aircraft will descend almost
vertically much like an elevator. To perform the
Elevator, make sure that you have sufficient altitude,
dive the aircraft vertically towards the ground and
pull full up on the elevator stick.
Hinged control surface located at the trailing edge
of the horizontal stabilizer, which provides control
of the airplane about the pitch axis and causes the
airplane to climb or dive. The correct direction of
control is to pull the transmitter Elevator control
stick back, toward the bottom of the transmitter, to
move the Elevator upward, which causes the
airplane to climb. Move the Elevator in the other
direction to dive.
This radio feature adjusts the length of servo travel
in one direction (a single channel will have
adjustments for two endpoints). If, for example,
your aircraft rolls faster one way than the other,
endpoint adjustments can correct the problem.
An organized flying contest with a set of rules.
RealFlight G4 currently supports five types of
Events: Limbo, Spot Landing, Pylon Racing,
Autorotation/Deadstick and Freestyle. You can
participate in Events by yourself or with other
RealFlight users over the internet. Use the Event

300

menu to start an Event.

Exponential
R/C Term

Figure 8
R/C Term

Flap
R/C Term

A feature commonly found on computer radios that

desensitizes the servo when the sticks are close to
the neutral position. The further the stick position
from center, the faster the control response.
This is an excellent maneuver to learn perspective
and orientation of the aircraft from all angles. Use
the ailerons and elevator to turn the aircraft left and
right. Use the elevator to ensure that the aircraft
maintains a constant altitude, forming an 8 in the
sky.
For Airplanes: hinged control surface located at the
trailing edge of the wing inboard of the ailerons.
The Flaps are lowered to produce more
aerodynamic lift from the wing, allowing a slower
takeoff and landing speed. Flaps are often found on
scale models, but usually not on basic trainers.
For Helicopters: Flapping is an up-and-down
motion of the main rotor blade's tip. With a "dualdamped" head, (as used in the Kyosho Concept
helicopters, for example) both blades are able to
Flap independently. With "solid axle" heads (as
used in the Hirobo Shuttle helicopters, among
others), moving one blade up causes the other to
move down.

Flapping Head
R/C Term

Flare
R/C Term

FlexiField
RealFlight Term

This describes a type of rotor head in which the two

blades are not connected directly. Each blade is
independent of the other, usually resulting in a
helicopter with smoother performance.
The point during the landing approach in which the
pilot increases the amount of up elevator to smooth
the touchdown of the airplane.
FlexiField is the most advanced flying site editor
ever unveiled. It presents the modeler with the
ability to adjust the flying site in virtually any
manner desired. The user can add trees, selecting
the type, size and color; add, move, size and orient
buildings, walls and other scenery objects; position
and orient the runway; even choose the amount and
type of lighting at the flying site.

301

Flight Failures
RealFlight Term

Flight Playback Gadget

RealFlight Term

Float Fly
R/C Term

Flybar Paddles
R/C Term

Four-Point Roll
R/C Term

Frame Rate
Computer Term

Freestyle Event
RealFlight Term

Fuselage
R/C Term

Futaba
R/C Term

Gadget
RealFlight Term

RealFlight G4 authentically recreates common

difficulties that may be experienced at your local
flying site. Practicing with flight failures enabled is a
good way to practice for emergencies.
A gadget that lets you control playback of flight
recordings using mouse actions.
The ability to takeoff and land a radio controlled
aircraft from water.
These are the short blades on the end of the flybar.
Available in a variety of weights and airfoils, these
paddles assist the main blades in producing lift, etc.
These maneuvers are very similar to a slow roll with
the exception of a hesitation at either of the roll
or at 1/8 of the roll. It is important to remember to
use rudder and elevator to keep the aircraft flying in
a straight line.
Frame Rate is the number of times per second that
RealFlight creates a different picture to display on
your monitor. Frame rate is determined by the
speed of your CPU and graphics card, and how
many RealFlight options you turn on. This is not
the same as refresh rate, which is the number of
times per second that your monitor retraces an
image on its screen.
An event where players decide on the rules.
RealFlight G4 sees that each player gets a turn; it is
the players responsibility to judge the competition.
Use this event when you have devised a group
activity that requires every player to take a turn.
Generally speaking, this is the main part of the
airplane that holds the wings and engine. The
fuselage is often thought of as the body of the
airplane. This term is also used to refer to a body
that might be used on helicopters.
Maker of high quality R/C products, including the
USB InterLink Elite controller shipped with
RealFlight G4.
An on-screen display that shows you continuously
updated information about your aircraft, or lets you

302

control RealFlight features using mouse clicks.

Global Wind
RealFlight Term

Governor
R/C Term

Grouping
RealFlight Term

Gyro
R/C Term

HAL Device
Computer Term

Harrier
Computer Term

Host
RealFlight Term

This term describes the overall wind conditions in

the simulation.
A device used to help maintain a constant RPM
(head speed). Generally used in helicopters rather
than airplanes.
A collection of scenery objects or foliage objects in
your airport. Every object in the airfield must
belong to one Group. You can place all of your
airport's scenery objects in a single Group, or create
multiple Groups to place objects in categories with
related objects. For example, you could have a
Group for Trees and another group for Buildings
within a particular airport.
A device, most commonly used in helicopters, that
aids in controlling the yawing action of the
helicopter by automatically adjusting the deflection
of the tail rotor blades.
A hardware-accelerated 3D video card driver.
HAL is an abbreviation for the phrase Hardware
Abstraction Layer that uses software drivers to
communicate between RealFlights software and the
hardware of the PC.
A Harrier is a slow forward progression of the
aircraft with the nose held high. Use the elevator to
stall the forward progress of the aircraft. Add in
more up elevator until the nose approaches 45
degrees. The throttle should be used to control the
forward progress of the aircraft, without climbing.
In RealFlight G4, every multiplayer session requires
one player to serve as Host. The Host starts the
session, and then the other players join. Other
players can leave the session whenever they want,
but only the Host can terminate the entire session.
The Host must start any multiplayer event (Limbo,
Spot Landing, Pylon Racing, Autorotation,
Freestyle).

303

Hot Pluggable/Hot
Swappable
Computer Term

Hub
R/C Term

Humpty-Bump
R/C Term

IP Address
Computer Term

Immelman Turn
R/C Term

Interface Mode
RealFlight Term

InterLink Elite Controller

RealFlight Term

Joystick
Computer Term

A device is said to be Hot Pluggable or Hot

Swappable when you can safely connect or
disconnect it without turning off your computer or
rebooting.
The centralized mechanical device used to attach
the main rotor blades and paddles.
This aerobatic maneuver consists of two vertical
lines connected by a half circle flown across the top.
Whenever your computer is connected to the
internet, it has an IP address. This number is a
string of digits and periods, and looks something
like 123.45.6.78. The IP address is like an internet
zip code that tells other computers where to look
for your computer. Depending on your internet
connection, your IP address may always be the
same, or may change each time you connect to the
internet. For other RealFlight G4 users to join your
Multiplayer session, they must obtain your IP
address. You can either provide it to them directly,
or post it through the RealFlight list server.
The aircraft will enter a half loop from straight and
level flight followed immediately by a half roll to
straight and level flight.
With RealFlight G4 set to Interface Mode, you are
using the InterLink Elite Controller as an interface
to your own R/C radio. In Interface Mode, your
own radio controls RealFlight G4. Conversely, in
Joystick Mode the InterLink Elite Controller (used
as a mockup of a R/C transmitter) controls the
RealFlight G4 aircraft.
Great Planes USB InterLink Elite Controller by
Futaba is a USB device shipped with RealFlight G4.
The InterLink Elite Controller can be used as a
standalone mockup R/C controller, as an
interface for using your own R/C transmitter to
control RealFlight, or both simultaneously!
A device that connects to your computer to provide
control input for the simulated aircraft. The
InterLink Elite controller that comes with

304

RealFlight G4 is considered a Joystick.

Joystick Emulation Interface
RealFlight Term

Joystick Mode
RealFlight Term

Launcher
RealFlight Term

LAN
Computer Term

Lead Lag
R/C Term

Leading Edge
R/C Term

Limbo
R/C Term

List Server
RealFlight Term

A term used to describe using your own radio to

emulate the Interlink Joystick. This allows you to
use your own radio to fly any of the stock aircraft in
RealFlight G4. Actual radio functions such as
mixing and ATVs are performed in the RealFlight
software, not on your radio. This is in contrast to
the Direct Control Interface.
With RealFlight G4 set to this mode, RealFlight G4
is controlled by the InterLink Elite controller used
as a mockup of a R/C transmitter.
The RealFlight G4 Launcher is useful for many
aspects of the G4 program, including loading the
simulator, compiling system information for
technical support, or uninstalling RealFlight.
Local Area Network. This is usually a network
where the computers are connected with high speed
network cards.
A helicopter term describing the hinge point where
the blade attaches to the hub. This allows the blade
to move forward and backward at certain times
during the blades rotation.
The very front edge of the wing or stabilizer. This is
the edge that hits the air first.
An event (flying competition) in which pilots take
turns flying their aircraft under a Limbo bar. The
pilot that clears the lowest bar height wins.
RealFlight G4s Multiplayer function lets you
publicly post your session, so that any RealFlight
G4 user, anywhere in the world, can find out about
your session and join you (assuming you have not
reached the enrollment limit of your session). The
place where you post your session is called a List
Server. Use of the List Server is optional. You can
preserve privacy by not posting your session, and
privately communicating your IP address to your
selected multiplayer partners.
Please note that the free, public list server for use by
RealFlight owners may be modified or discontinued

305

without notice at any time.

Low Rates
R/C Term

Mode
R/C Term

Most Recently Used (MRU)

Computer Term

MultiMode
RealFlight Term

Multiplayer
Computer Term

Multiplayer Session
RealFlight Term

NavGuides
RealFlight Term

Parent Item
RealFlight Term

PhotoField
RealFlight Term

Pirouette
R/C Term

A switch on the radio that reduces the servo

movement to much smaller extremes, thus making
the model respond more slowly to a given control
input.
Also known as Flight Mode or Stick Mode, this
refers to the transmitter's gimbal stick assignments
(locations) which determine the flight mode of your
controller. There are two main modes of control,
Mode 1- mostly used in Europe and Mode 2 which
is the predominant method of controlling aircraft
commonly used in the United States.
MRU refers to the list of documents which were
last accessed. For RealFlight G4, MRUs appear for
airports, aircraft and recordings.
A G4 feature that allows two users to fly
simultaneously on the same PC.
A RealFlight G4 feature that uses Microsoft's
DirectX technology to connect with other
RealFlight G4 users over a network.
A network connection between RealFlight G4 users
that allows each user to fly in the same "virtual
world," and allows all participants to see and interact
with each other's aircraft.
A gadget that displays continuously updated
information about your aircraft and the virtual
world.
In many of RealFlight G4s selection windows,
items are displayed in a hierarchy format. An item
that has additional item within it is considered the
parent item.
A technology that creates a flying field by using a
panoramic photograph as a background for a flat
terrain.
The yawing action of a helicopter that looks much
like an ice skater spinning in a circle. One Pirouette
is equal to one 360-degree rotation.

306

Pitch Axis
R/C Term

Plumb String
R/C Term

Point Rolls
R/C Term

Private Session
RealFlight Term

Propeller
R/C Term

Public Session
RealFlight Term

Pylon Racing
R/C Term

QuickSelect
RealFlight Term

The airplane axis is controlled by the elevator. Pitch

is illustrated by holding the airplane at each wingtip.
Raising or lowering the nose is the pitch movement.
This is how the climb or dive is controlled.
When you measure your aircraft for RealFlight,
some measurements require that you have a
reference line running straight up and down. To
make such a line, we tie a weight to the free end of a
string, and let the weight dangle. Because the string
is then plumb (oriented straight up and down), it
is called a Plumb String. A Plumb String is
particularly useful in measuring an aircrafts center
of gravity.
These maneuvers are very similar to a roll with the
exception of a hesitation at either 1/4 or 1/8 of the
roll.
A multiplayer session that is not published on our
list server. For a private session, the host must
distribute his/her IP address to each participant,
who must manually enter this information to join.
Props are generally designated by two numbers (for
instance, 10 6). The first number is the length
(10" in the example) of the prop. The second
number is the pitch or angle of the blades. In this
example, the 6 represents the distance the
propeller will move forward in one revolution.
A multiplayer session that is published on a list
server.
An event (flying competition) in which pilots take
turns flying their aircraft around a closed course.
Pylons mark the course perimeter. The pilot that
finishes the course first wins.
RealFlight G4 InterLink Elite allows you to make
changes to the simulator with the controller using
the buttons at the bottom. Manipulating these
buttons through the on-screen QuickSelect tabs
offer the ability to change aircraft, flying sites, and
more.

307

RAM

Random Access Memory.

Computer Term

ReadySelect
RealFlight Term

RealPhysics 3D
RealFlight Term

Refresh Rate
Computer Term

Resolution
Computer Term

Roll Axis
R/C Term

Rolloff Factor
RealFlight Term

Root
RealFlight Term

Rudder
R/C Term

This is the name given to RealFlight G4s rotating

preview box. This allows a rapid view of the aircraft
from all angles.
This is RealFlights exclusive physics modeling
technology. RealPhysics 3D authentically replicates
the actual physics of model aircraft by performing
hundreds of thousands of floating point calculations
each second while delivering sizzling real time
performance.
The number of times per second that your monitor
retraces an image on its screen. This is different
from the Frame Rate.
When used in the context of screen Resolution, this
term describes the picture quality of the screen.
Lower Resolutions will produce an image that is not
as sharp as higher Resolutions.
The airplane axis controlled by the ailerons. Roll is
illustrated by holding the airplane by the nose and
tail. Dropping either wingtip is the roll movement.
Roll is used to bank or turn the airplane. In most
airplanes, the ailerons control roll. However, when
the main wing has dihedral, the plane can be banked
using the rudder only. Consequently, many planes
with wing dihedral do not have ailerons, and the
rudder controls both roll and yaw. This is one
reason why most trainer aircraft have a large
amount of dihedral -- a plane with large dihedral can
be controlled using fewer input channels.
This phrase describes how rapidly the volume of a
sound increases or decreases as the source draws
closer or moves farther away.
In many of RealFlight G4s selection windows,
items are displayed in a hierarchy format. The
upper most item in this hierarchy is considered the
Root item.
Hinged control surface located at the trailing edge
of the vertical stabilizer, which provides control of
the airplane about the Yaw axis (causing the airplane

308

to Yaw left or right). Left Rudder movement

causes the airplane to Yaw left, and right Rudder
movement causes it to Yaw right.
Servo
R/C Term

Session

An electromechanical device that moves the control

surfaces or throttle of an airplane according to
commands from a receiver. This device does the
physical work of moving parts around inside the
aircraft.
See "Multiplayer Session."

RealFlight Term

Software Radio
RealFlight Term

Sound Card
Computer Term

Specular Highlights
Computer Term

Split S
R/C Term

Spot Landing
R/C Term

Stall
R/C Term

This term describes RealFlight G4s ability to

accurately mimic a computer transmitter (complete
with mixing, etc.) in the simulation.
A card inside your computer that controls audio
(what you hear over your computer speakers).
Most sound cards plug into your computers
motherboard. You can upgrade your sound card
(or the software driver that controls it) without
getting a new computer.
A graphics rendering technique that makes surfaces
(e.g., MonoKote) appear reflective, or shiny, in
direct light (e.g., sunlight).
The Split S is another step in learning to combine
loops and rolls and is a great maneuver to decrease
your altitude. A half roll precedes a half loop,
making the maneuver a mirror image of the
Immelman. The Split S provides course reversal
and an easy increase in speed.
An event (flying competition) in which pilots take
turns trying to touch their aircraft down within a
small marked landing area. Each pilot receives a
score based on touch down location. The pilot with
the highest score wins the event.
When an airplanes angle of attack is too great to
generate lift (regardless of airspeed), the plane will
dive and rapidly lose altitude. This is known as a
stall. Every airfoil has an angle of attack at which it
generates maximum lift. The airfoil will stall beyond
this angle.

309

Swash Plate
R/C Term

Thermal System
R/C Term

Throttle Hold
R/C Term

Tip Stall
R/C Term

Torque Roll
R/C Term

Touch and Go
R/C Term

Trailing Edge

The mechanism in a helicopter rotor that turns nonrotating control movements into rotating control
movements.
This phrase describes the wind flow and effects for
the thermals in RealFlight G4.
This is used to keep the throttle at a set position, yet
allows input to the collective of the helicopter.
Generally this function is used to practice
autorotation.
This is when the airplane reaches its stall speed and
one wing drops.
The Torque Roll occurs when the nose of the
airplane is pointed vertically and the airplane hovers
in place. The aircraft will rotate left around its roll
axis.
Landing and taking off without a pause. Often
confused with a good bounce.
The rearmost edge of the wing or stabilizer.

R/C Term

Trainer
R/C Term

Training Aids
RealFlight Term

TruFlo Wind Dynamics

RealFlight Term

Turbulence System
RealFlight Term

USB
Computer Term

A model designed to be inherently stable and fly at

low speeds, to give first-time modelers time to think
and react as they learn to fly.
RealFlight G4 offers a variety of features to learn
new maneuvers. These consist of training aids that
take you through, step-by-step, basic flight lessons,
such as Takeoffs and Landings for airplanes, and
Hovering practice for helicopters. Pre-recorded
lessons are also available from professional pilots.
RealFlight G4s TruFlo Wind Dynamics is the most
accurate wind model ever released in an R/C
simulator. It combines five different wind models
to recreate the ever-changing wind fields found at a
real flying site.
This is the ability of RealFlight to induce turbulent,
rough air, as would be experienced at the flying site.
USB, or Universal Serial Bus, is a connection
protocol for computer peripheral devices (like Great
Planes USB InterLink Elite Controller by Futaba).

310

USB technology allows you to connect multiple

devices to your computer, and supports high data
transfer rates and is hot swappable. USB devices
have a special connector that only fits into a USB
port. Most modern personal computers have USB
ports, which are usually clearly labeled. Some
computers have one or more USB ports on the
front of the computer housing, although the USB
ports are usually on the back of the computer.
Variometer
R/C Term

Video Card
Computer Term

Viewport
RealFlight Term

Virtual Flight Instruction

RealFlight Term

VirtualRevolution
RealFlight Term

Washout
R/C Term

An instrument designed to indicate the rate of climb

or descent of an aircraft.
A card inside your computer that produces the
images on your video monitor. Most modern 3D
video cards have accelerated 3D operationsthat
is, they perform numerical calculations for rendering
a 3D scene, to free up your computers CPU to
perform other tasks. The video card plugs into your
computers motherboard. You can upgrade your
video card (or the software driver that controls it)
without replacing your computer.
A picture-in-picture display set within the RealFlight
G4 main display. The Viewport is independently
adjustable and serves as its own unique window on
the world.
This RealFlight G4 feature lets you choose from a
variety of prerecorded maneuver training lessons.
The maneuver is then demonstrated on screen,
along with the instructors voice and control stick
movements. You can index, pause and even loop
the maneuver playback for training purposes.
This is the exclusive sound technology used by
RealFlight G4. As with the original RealFlight
programs, the sounds are Doppler-correct. If the
users sound card supports it, surround sound is
also available.
An intentional twist in the wing, which causes the
wing tips to have a lower angle of attack than the
wing root. In other words, the trailing edge is
higher than the leading edge at the wing tips.
Washout helps to prevent tip stalls.

311

Waterfall
R/C Term

Wing Loading
R/C Term

The Waterfall is a maneuver where the plane pivots

360 degrees in the pitch axis with as little forward
motion and altitude deviation as possible. As the
name suggests, this maneuver resembles a waterfall
during flight.
The amount of weight per square foot that has to
be overcome to provide lift. It is normally
expressed in ounces per square foot.
This
specification can be easily calculated as follows: first
determine the area of the wing in square inches.
Then simply divide by 144 to obtain square feet.
Divide the total weight (in ounces) of the airplane
by the wing area (in square feet).
This information is valuable when deciding on
which airplane to build next. Planes with high wing
loading must fly faster to stay in the air. These are
generally "performance" airplanes. Conversely, a
plane with lower wing loading does not need as
much air flowing around the wing to keep it flying.
Gliders and trainer airplanes fall into this category
because in this case, slow, efficient flight is highly
desirable.

Yaw Axis
R/C Term

The airplane axis controlled by the rudder. Yaw is

illustrated by hanging the airplane level by a wire
located at the center of gravity. Left or right
movement of the nose is the Yaw movement.

312

Index
A
About, 264

Camera Position, 234

AccuModel, 3, 295

Camera Type, 233

Advanced Flight Recorder, 4, 295

Capture Screenshot, 60

Aerobatics, 271

Channel, 140

AFR. See Advanced Flight Recorder

Channel Mapping, 139, 145, 297

Aircraft Editor, 113

Channel Modification, 143

Add Component, 125

Chase View, 234

Aircraft Parts Tree, 121

Chat, 88, 181, 252, 297

Delete Component, 125

Child, 45, 122, 297

Parameter Window, 124

Clear Aircraft Position, 130

Preview Screen, 124

Close All, 257

Show Wireframe, 121

Clouds, 94

Aircraft Menu, 109

Cockpit View, 234

Aircraft MRU, 21, 133

Collective, 273

Aircraft Selection, 19, 111, 112

Collisions, 101

Description, 112

Color Scheme, 72, 113

Specifications, 112

ColorSchemes, 128

Aircraft Variant, 73

Alpha Channels, 129

Airframe, 296

PowerReflectiveOff, 128

Airplane Basics, 269

PowerReflectiveOn, 128

Airplane Flight, 270

PowerSpecularOff, 128

Airplane Hover Trainer, 218

PowerSpecularOn, 128

Airplane Physics. See Physics

Reflectivity, 128

Airport Editing, 31

Specular, 128

Airport MRU, 22, 108

Commands, 90

Airport Selection, 21, 38

Commit Line, 162

Airspeed, 247

Console, 81, 252

Altitude, 246, 253

Contrast, 97

Arrange, 256

Controller. See InterLink Elite

Attempts Per Turn, 163

Controller Calibration, 137, 143

Audio, 77

Controller Menu, 135

Auto-Play, 296

Crash Eliminates Player, 153, 158, 163, 173

Autorotation, 151, 154, 297

Crashing, 269

Autozoom, 238

Crosswind, 206, 210

Cut Penalty, 167

Base, 211

Cyclic Stick, 275

Battery, 254
Binocular, 248

Bloom, 95, 297

Data Lever, 299

Boot Player, 188

Deadstick, 151, 154, 299

Boundary, 206, 210, 214, 220

Direction, 206, 211

Brightness, 97

DirectX, 13, 291, 299

Disconnect, 187

Camera, 80

Display Properties, 288

Cuts Allowed, 167

Display Advanced Properties, 118

313

Distance Between Poles, 163

Hovering, 278

Distance between pylons, 168

Hovering Training Aids, 3

Distance to Drop Bar, 162

Downwind, 211

Drivers, 12, 291, 300

Idle-Up, 277

Import, 69

Edit Airport, 31, 40

Interface Mode, 304

End Current Event, 176

InterLink Elite, 2, 4, 12, 13, 33, 136, 142,

Instructions, 82

Environment, 62

147, 304

Errors, 87

IP Address, 180, 185, 304

Events Menu, 149

Events Viewport, 156, 160, 165, 170, 175

Export, 72, 75

Join, 184

Joystick Emulation, 144, 145, 305

Final, 211

Keep Ground in View, 238

Fixed Position, 234

FlexiField, 4, 31, 301

Flight Failures, 5, 66, 91, 302

KEX, 70

Float Fly, 3

Keyboard Commands, 263

Folder Listing Window, 51, 52

Kill Engine, 132

Foliage Density, 95

Knife Edge Software, 267

Forfeit Turn, 176

Knowledge Base, 290, 292

Forward Flight, 278

Freestyle, 156, 159, 302

Futaba, 302

LAN, 179, 305

Landing Trainer, 3, 207

G Force, 254

Laps to complete, 167

G3X. See RealFlight Archive

Latency, 187

Gadgets, 26, 196, 245, 302

Launcher, 5, 279, 305

Global Wind, 303

License, 265

Graphics, 93, 247

Limbo, 160, 164

Graphics Frame Rate, 255

List Server, 183, 305

Great Planes, 267

Look At, 120, 235

Ground Speed, 254

Look From, 121

Grouping, 39, 49, 112, 303

Joystick Mode, 142, 144, 305

Landings, 271

Gyro, 277

Manage User Files, 74

Head Tracking, 241

Map To, 141

Heading, 247, 254

Max Players, 183

Height, 255

Maximum Bar Height, 162

Heli Hover Trainer, 211

Message Boards, 290, 292

Heli Orientation Trainer, 224

Metric Units, 51, 102, 119

Helicopter Basics, 272

Microphone, 199

Helicopter Physics. See Physics

Minimum Bar Height, 162

Help Contents, 262

Mode 1, 143

Help Menu, 261

Mode 2, 143

Host, 181, 185, 186

Mode 3, 143

Manual View, 238

314

Mode 4, 143
Movement Modes, 40

MRU, 306

Radio Gadget, 228, 247

MultiMode, 100, 189, 306

Radio Mode, 256

Multiplayer, 100, 149, 179, 306

Raw Panoramic Image, 70

Multiplayer Menu, 179

ReadySelect, 308

Multiplayer Session, 181

RealFlight Archive, 71

Mute Audio, 61

RealPhysics, 2, 308

Recordings, 193

NaturalPoint, 241

Recordings MRU, 200

NavGuides, 5, 246, 252, 300, 306

Refresh Rate, 99

Night Flying, 3, 95

Registration, 281

Normal Camera, 47

Reload Color Scheme, 119

Notifications, 85

Remember Aircraft Position, 129

Reset, 131

Object Palette Window, 52, 55

Restore Defaults, 281

Options, 175

Reverse Channel, 141

Orientation, 215, 221

RFX. See RealFlight Archive

RotoSonics, 4

Pan Camera, 46

Rudder, 274

Parent, 45, 122, 306

Particles, 94, 96

Pass Through Interface, 144, 146

Save Color Scheme, 126

Performance, 293

Scenery, 94

PhotoField, 3, 306

Select Color Scheme, 125

Physics, 101, 102

Select Controller, 136

Physics Frame Rate, 255

Select Level, 226

Pilot Name, 100, 152, 157, 166

Session Name, 183, 186

Pilot Preview, 52, 57

Settings, 76

Pivot Camera, 46

Shadow, 94, 95, 96

Play Engine Sounds, 118

Show Title Bar, 244

Playback Gadget, 196

Simulation Menu, 37

Player Kills Engine, 153

Software Radio, 309

Players, 187

Sound Card, 8

Port Number, 183, 186

Specific Version, 283

Preview Screen, 39

Speed, 254

Private, 307

Split Screen. See MultiMode

Probability, 91

Spot Landing, 170, 173, 309

Properties, 52

Stick Mapping, 143

Properties Window, 54

Streamers, 5, 96

Public, 307

Sun, 62

Recordings Menu, 193

Resolution, 99

RPM, 247, 254

Publish Hosting Information, 188

Sun Azimuth, 63

Pylon Racing, 165, 168, 307

Sun Inclination, 63
System Information, 285

System Requirements, 7

Quick Look, 236

QuickSelect, 3, 23, 24, 34, 35, 40, 111, 237,

246, 248, 249, 250, 251, 307

Takeoff Trainer, 3, 202

315

Takeoffs, 270

Variometer, 251, 311

Targa (.tga) File Format, 127

Vertical Sync, 100

Target Scale, 153, 172

VFI. See Virtual Flight Instruction

Technical Support, 283, 285, 286, 290, 292

Video Card, 8

Terrain Detail, 94

View Menu, 231

Texture, 96

Viewport, 5, 25, 249, 311

Three Pylons on Course, 168

Viewport List, 258

Threshold Rules, 168

Virtual Flight Instruction, 4, 26, 226, 311

Throttle cut altitude, 153

VirtualRevolution, 4, 311

Throttle Hold, 277

Voltage, 254

Time to Complete Turn, 153, 158, 163, 172

TrackIR, 241

Training Aids, 29, 201, 310

Warnings, 86

Training Menu, 201

Water, 95

Transmitter, 16, 143

Weather, 103

Transmitter Mode, 142, 143, 145, 146

Websites, 266

Trees, 94

Wind, 64, 103, 206, 210, 247, 255

TruFlo Wind Dynamics, 3, 310

Global Wind, 103

Turbulence, 105

Wind Direction, 104

Layer Height, 106

Wind Gust, 105

Micro-Turbulence Strength Proportion,

Wind Variation, 105

Wind Velocity, 104

107

Wind Direction, 65

Strength Proportion, 106

Turns Per Event, 152, 158, 163, 173

Wind Field Indicators, 95

Wind Speed, 65

U.S. Patent, 33
Uninstalling, 284

Unlimited Fuel, 102

Zone Point Values, 152, 172

Updates, 281, 291

Zoom, 255

USB, 2, 310

Zoom In, 48, 239

Zoom Out, 48, 239

Variable Pitch Prop, 3

Zoom Type, 237

Window Menu, 243

Zoom Reset, 48, 240

316

317

License
REGISTERED VERSION: RealFlight(r) R/C Simulator
LIMITED USE SOFTWARE LICENSE AGREEMENT
This Limited Use Software License Agreement (the "Agreement") is a legal agreement
between you, the end-user, and Knife Edge Software ("KES"). By continuing the installation of
this game program, by loading or running the game, or by placing or copying the game program
onto your computer hard drive, you are agreeing to be bound by the terms of this Agreement. If
you do not agree to the terms of this Agreement, promptly return the game program and the
accompanying items (including all written materials), along with your receipt to the place from
where you obtained them for a full refund.
KES SOFTWARE LICENSE
1.
Grant of License. KES grants to you the limited right to use one (1) copy of the
enclosed or foregoing game program (the "Software") on a single computer. You have no
ownership or proprietary rights in or to the Software or the written materials accompanying the
Software. For purposes of this section, "use" means loading the Software into RAM, as well as
installation on a hard disk or other storage device. The Software shall be either returned to KES
or destroyed when no longer used in accordance with this Agreement, or when the right to use
the Software is terminated. You agree that the Software will not be shipped, transferred or
exported into any country in violation of the U.S. Export Administration Act (or any other law
governing such matters) and that you will not utilize, in any other manner, the Software in
violation of any applicable law.
2.
Commercial Use is Prohibited. Except as provided in paragraph 5. Herein below in
regard to the Software, under no circumstances shall you, the end-user, be permitted, allowed or
authorized to commercially exploit the Software, any data comprising the Software. Neither you
nor anyone at your direction shall do any of the following acts (any such acts shall be deemed void
and a breach of this Agreement) with regard to the Software, or any portion thereof, such as a
screen display or a screenshot:
a. Rent the Software;
b. Sell the Software;
c. Lease or lend the Software;
d. Offer the Software on a pay-per-play basis;
e. Distribute, by electronic means or otherwise, the Software for money or any other
consideration; or
f. In any other manner and through any medium whatsoever commercially exploit the Software or
use the Software for any commercial purpose.
319

3.
Additional Prohibited Uses. Neither you nor anyone at your direction shall take the
following action in regard to the Software, or any portion thereof, such as a screen display or a
screenshot:
a. Modify, disassemble, reverse engineer or decompile Software;
b. Translate the Software;
c. Reproduce the Software;
d. Publicly display the Software;
e. Prepare derivative works based upon the Software except Permitted Derivative Works); or
f. Distribute, by electronic means or otherwise, the Software.
4. Use of Other Material is Prohibited. Use, in any manner, of the trademarks, such as
RealFlight R/C Simulator (tm) logo, or symbols, art work, images, screen displays or screenshots,
sound effects, music, and other such material contained within, generated by or relating to the
Software is prohibited.
5. To Receive Permission to Commercially Exploit. If you desire to commercially exploit
the Software, you may request a copy of and execute the Commercial Exploitation License
Agreement for RealFlight R/C Simulator (the "License") and forward the original License to
KES Software at the address noted therein. Please note that KES may refuse your request and
not sign the License in KES's sole discretion.
6.
Restrictions Apply to Third Parties. The prohibitions and restrictions described herein
apply to anyone in possession of the Software and/or Permitted Derivative Works.
7. Copyright. The Software and all copyrights related thereto (including all characters and
other images generated by the Software or depicted in the Software) is owned by KES and is
protected by United States copyright laws and international treaty provisions. You must treat the
Software like any other copyrighted material. You may not otherwise reproduce, copy or disclose
to others, in whole or in any part, the Software. You may not copy the written materials
accompanying the Software. The same restrictions and prohibitions regarding your use of the
Software as provided in this Agreement apply to your use of the written materials accompanying
the Software. The written materials are owned by KES and are protected by United States
copyright laws and international treaties. You agree to use your best efforts to see that any user of
the Software licensed hereunder complies with this Agreement.

8. Limited Warranty. KES warrants that if properly installed and operated on a computer
for which it is designed, the Software will perform substantially in accordance with the
accompanying written materials for a period of ninety (90) days from the date of purchase of the
Software. KES's entire liability and your exclusive remedy shall be, at KES's option, either (a)
return of the price paid or (b) repair or replacement of the Software that does not meet KES's
Limited Warranty. To make a warranty claim, return the Software to Hobby Services at 3002

320

North Apollo Drive, Suite #1, Champaign, IL 61822 accompanied by proof of purchase, your
name, your address, and a statement of defect, or return the Software with the above information
to KES. This Limited Warranty is void if failure of the Software has resulted in whole or in part
from accident, abuse, misapplication or violation of this Agreement. Any replacement Software
will be warranted for the remainder of the original warranty period or thirty (30) days from your
receipt of the replacement software, whichever is longer. This warranty allocates risks of product
failure between Licensee and KES. KES's product pricing reflects this allocation of risk and the
limitations of liability contained in this warranty.
9.
NO OTHER WARRANTIES. KES DISCLAIMS ALL OTHER WARRANTIES,
BOTH EXPRESS IMPLIED, INCLUDING BUT NOT LIMITED TO, IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE WITH RESPECT TO THE SOFTWARE AND THE ACCOMPANYING
WRITTEN MATERIALS. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS. YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM JURISDICTION
TO JURISDICTION. KES DOES NOT WARRANT THAT THE OPERATION OF THE
SOFTWARE WILL BE UNINTERRUPTED, ERROR FREE OR MEET LICENSEE'S
SPECIFIC REQUIREMENTS. THE WARRANTY SET FORTH ABOVE IS IN LIEU OF
ALL OTHER EXPRESS WARRANTIES WHETHER ORAL OR WRITTEN. THE
AGENTS, EMPLOYEES, DISTRIBUTORS, AND DEALERS OF KES ARE NOT
AUTHORIZED TO MAKE MODIFICATIONS TO THIS WARRANTY, OR
ADDITIONAL WARRANTIES ON BEHALF OF KES. ADDITIONAL STATEMENTS
SUCH AS DEALER ADVERTISING OR PRESENTATIONS, WHETHER ORAL OR
WRITTEN, DO NOT CONSTITUTE WARRANTIES BY KES AND SHOULD NOT BE
RELIED UPON.
10. Exclusive Remedies. You agree that your exclusive remedy against KES, its affiliates,
contractors, suppliers, and agents for loss or damage caused by any defect or failure in the
Software regardless of the form of action, whether in contract, tort, including negligence, strict
liability or otherwise, shall be the return of the purchase price paid or replacement of the
Software. This Agreement shall be construed in accordance with and governed by the laws of the
State of Oregon. Copyright and other proprietary matters will be governed by United States laws
and international treaties. IN ANY CASE, KES SHALL NOT BE LIABLE FOR LOSS OF
DATA, LOSS OF PROFITS, LOST SAVINGS, SPECIAL, INCIDENTAL,
CONSEQUENTIAL, INDIRECT OR OTHER SIMILAR DAMAGES ARISING FROM
BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, OR OTHER
LEGAL THEORY EVEN IF KES OR ITS AGENT HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY ANY OTHER PARTY.
Some jurisdictions do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
11. General Provisions. Neither this Agreement nor any part or portion hereof shall be
assigned, sublicensed or otherwise transferred by you. Should any provision of this Agreement be
held to be void, invalid, unenforceable or illegal by a court, the validity and enforceability of the
other provisions shall not be affected thereby. If any provision is determined to be
unenforceable, you agree to a modification of such provision to provide for enforcement of the
provision's intent, to the extent permitted by applicable law. Failure of a party to enforce any
provision of this Agreement shall not constitute or be construed as a waiver of such provision or

321

of the right to enforce such provision. If you fail to comply with any terms of this Agreement,
YOUR LICENSE IS AUTOMATICALLY TERMINATED.
YOU ACKNOWLEDGE THAT YOU HAVE READ THIS AGREEMENT, THAT
YOU UNDERSTAND THIS AGREEMENT, AND UNDERSTAND THAT BY
CONTINUING THE INSTALLATION OF THE SOFTWARE, BY LOADING OR
RUNNING THE SOFTWARE, OR BY PLACING OR COPYING THE SOFTWARE
ONTO YOUR COMPUTER HARD DRIVE, YOU AGREE TO BE BOUND BY THIS
AGREEMENT'S TERMS AND CONDITIONS. YOU FURTHER AGREE THAT,
EXCEPT FOR WRITTEN SEPARATE AGREEMENTS BETWEEN KES AND YOU,
THIS AGREEMENT IS A COMPLETE AND EXCLUSIVE STATEMENT OF THE
RIGHTS AND LIABILITIES OF THE PARTIES. THIS AGREEMENT SUPERSEDES
ALL PRIOR ORAL AGREEMENTS, PROPOSALS OR UNDERSTANDINGS, AND ANY
OTHER COMMUNICATIONS BETWEEN KES AND YOU RELATING TO THE
SUBJECT MATTER OF THIS AGREEMENT.

322

Credits
Produced By
Great Planes
PO Box 9021 Champaign, IL 61826
www.greatplanes.com
Developed by
Knife Edge Software
Corvallis, OR
www.knifeedge.com
Original Concept
Scott Kemp
Art
Lance Bass
Hays Clark
Tony Elms
Angela Kemp
Dave Lauck
Dana "Airworks" Loncto
Ted McClung
Aaron Moore
Kevin Nagatani
Mike Nagatani
Paul Naton
Lyaksandr Prelle-Tworek
DJ Vegh
Development
Scott Booth
Zach Brockway
Jim Coleman
Ryan Douglas
Dusty Eveland-DeWan
Mark Finch
Ed Koffeman
Aaron Moore
Japhet Stevens
Adam Taylor
Joe Teibel
Travis Vitek
Ted Zuvich

323

InterLink Elite
Futaba Corporation
Knife Edge Software

Flight Testing
Ryan Archer
Augusto Arevalo
Darrell Bell
Todd Bennett
Matthew Botos
Brian Bremer
Charles Dawson
Greg Duitsman
Mark Fadely
Jeff Fassbinder
Miguel Frontera
Kelly Gerber
John Glezellis
David A. Hourston
Dan Landis
Larry Markey
Sean McMurtry
Paul Naton
Pete Niotis
Frank Noll, Jr.
Jason Noll
Adam Ranck
Jason Shulman
Dino Spadaccini
Jeff Swartz
Jon Zaretsky
Malorie Zastrow
Marketing
Gordy Cockburn
Doug Outlaw
Product Artwork
Wally Armstrong
Mike Bowers
Rick Burtis
Seth Frederick
Howard Golub
Mike Johnson
Denitra Luster

324

Jeremy Motley
Jack Quigg
Project Management
Jim Bourke
Rick Piester
Bryan Schlueter
Mark Williams
Production
Rodney Clinton
Dan Lane
Dick Sumner
Bill Vowels
Technical Consultants
Michael Giger
Kevin Hisel
Testing
Corey Bruff
John Cox
Montana Harkin
Terry McBride
Mike McWethy
Lennie Morgan
Art Pesch
Kevin Phillips
George Rodriguez
Alex Sanabrais
Lisa Stirnemann
Chris Sydor
Aleks Weber
T.J. Weber
Christian Williams
David Wright
Dave Wolf
Special Thanks
Jill Brinkoetter
Neal Cloud
Teresa Fredericks
Ben Godwin
Bounchanh Grant
Bryan Heaton
Martin Hepperle
Daniel Kemphues
Neal Kuechler

325

Danielle LeFaivre
Dan Mason
P.B. Mink
Ang Overholt
Ryan Reeder
Jrgen Schrader
Eric Smith
Lisa "Weesa" Stirnemann
Bill Wiegand
Stefan Vorkoetter
A Big Thanks Also To
The families of those who put many
late nights into the production of
this product.
And To Knife Edge Mascots
The All-Seeing Gnome
LuLu the Hula Girl
Aircraft and Other Textures
Avant - Carbon Xtreme
F-86 - Michael Chan Su
Huey - Steve Stuart-Doig and Larry Jolly (www.ljmp.com)
Ion-X, Fury - Miniature Aircraft
Simple Flier - Alexandre Kolyvanov, Donald Miller
Legal
Program 2007, Knife Edge Software, LLC
Helicopter Paint Schemes 1999-2007, Knife Edge Software
Title Page, Box, CD Art, 2007, Hobbico, Inc.
FMOD sound and music system,
Firelight Technologies, Pty Ltd. 1994-2007
Airfoil data courtesy
UIUC Airfoil Coordinates Database
Prof Michael Selig, Department of Aero Engineering,
University of Illinois at Urbana-Champaign,
http://www.ae.uiuc.edu/
included under the terms of the GNU GENERAL PUBLIC LICENSE
An ASCII readable version of this data can be found on
your RealFlight G4 installation CD.
Seawind is a licensed trademark of Seawind/S.N.A., Inc.
Seawind logo is used with permission of Seawind/S.N.A., Inc

326

Portions of this software utilize SpeedTree technology.

2002 Interactive Data Visualization, Inc. All rights reserved.
Electric power system database courtesy of
Capable Computing Inc., creators of MotoCalc.
This software is based in part on the work of
the Independent JPEG Group
All trademarks and registered trademarks are the property
of their respective owners.

327