SCORGTM V5.

1, 2015

SCORGTM Setup for CFD Simulation of

Twin Screw Machines with Simerics Inc.
PUMPLINX Solver
SCORGTM is the CFD grid generation tool for rotary twin screw machines. The tool includes
additional modules for designing and editing rotor profiles, executing a basic thermodynamic
calculation based on quasi 1D chamber models and generating the deforming working
chamber grids for selected commercial CFD solvers. For more information on the product
please visit the website: www.pdmanalysis.co.uk or refer to documentation help.
This guide lists the steps for setting up a CFD simulation for Twin Screw Compressor with
SCORGTM and PUMPLINX r3.4.6 Solver. The user is expected to be familiar with screw
machines, CFD and PUMPLINX in order to be able to use these procedures. It is highly
recommended that books on that topic are studied12
Refer SCORGTM Installation Guide V5.1 for system and hardware requirements.

Table of Contents
1

Introduction ........................................................................................................................ 2

SCORGTM Project .............................................................................................................. 3

SCORGTM Mesh Generation.............................................................................................. 9

Pumplinx case setup ......................................................................................................... 15

Pumplinx Solver Calculation ........................................................................................... 21

Summary .......................................................................................................................... 22

Bibliography .................................................................................................................... 22

N. Stosic, I.K. Smith, A. Kovacevic Screw Compressor Mathematical Modelling and Performance Calculation, Springer,
UK 2005, ISBN-10 3-540-24275-9
2
A. Kovacevic. N. Stosic, I.K. Smith, Screw Compressor Three Dimensional Computational Fluid Dynamics and Fluid
Solid Interaction, Springer, 2006, ISBN 3-540-36302-5

TM

PDM Analysis Ltd, 2015

Page | 1

SCORGTM V5.1, 2015

1 Introduction
Screw Compressors are rotary positive displacement machines. Although the working
principle of these machines is simple, the geometry of rotors which are in the form of multi lobe helical screws meshing with each other, is making analysis by use of Computational
Fluid Dynamics (CFD) challenging. The process starts when the lobes are engaged at one
end, which creates continuous increase of the volume between the rotors and the casing
which reduces pressure in the suction domain and draws the working fluid in. Further rotation
of the rotors makes this volume between the rotors and the casing enclosed when the
compression of fluid begins. This increases the pressure within the chamber. Further rotation
exposes the pressurized fluid to the outlet port and the fluid is delivered (Stosic, et al., 2005).
Similar process is occurring in other helical screw machines such as pumps, vacuum pumps,
gear pumps, expanders, extruders and motors. The CFD is equally challenging in such
machines due to sliding and stretching
The main objectives of CFD simulations of a screw compressor are to:
a. Obtain the pressure field inside the rotor chamber and in the suction and discharge
domains. Example shown in Figure 1-1.
b. Obtain the velocity fields in critical regions of the computational domain.
c. Obtain temperature fields in critical regions of the computational domain.
d. Obtain integral parameters of the machine such as power, mass flow rate, discharge
temperature, torques on the rotor shafts, etc.
e. Obtain the loads and temperatures on boundaries with solid parts of the machine for
further structural and thermal analysis.

Figure 1-1 Pressure Variation diagram of a Twin Screw Compressor (Kovacevic, et al., 2007)
TM

PDM Analysis Ltd, 2015

Page | 2

SCORGTM V5.1, 2015

This Tutorial will provide a step by step guide for the procedure to setup and execute a
typical twin screw compressor, pump or motor simulation. An example of a dry air
compressor with 3/5 lobe combination, L/D ratio of 1.6 and wrap angle 285 deg has been
considered.

2 SCORGTM Project
Launch SCORGTM on the Desktop.
Select File New

Select N35_Template.spt Open

TM

PDM Analysis Ltd, 2015

Page | 3

SCORGTM V5.1, 2015

Save the project in a new folder named TwinScrewPumplinxSetup

SCORG_Grid_Tutorial.spf

The GUI of SCORGTM in the figure bellow shows the mains items of the front panel.

TM

PDM Analysis Ltd, 2015

Page | 4

SCORGTM V5.1, 2015

Go to Help Tutorials Folder opens
Copy the compressor rotor profile files [ 35MaleProfile_P1.dat and
35FemaleProfile_P2.dat ]
Copy the compressor suction and discharge port grids
[ SCORG_Pumplinx_Tutorial_Ports_V5.0.sgrd ]
Paste these files in the working directory TwinScrewPumplinxSetup

TM

PDM Analysis Ltd, 2015

Page | 5

SCORGTM V5.1, 2015

Go to User Profile Browse and Select the Male Rotor Profile from working
directory.
35MaleProfile_P1.dat
Similarly Select the Female Rotor Profile.
35FemaleProfile_P2.dat

Click Save.

Click Refresh to view new profiles.

TM

PDM Analysis Ltd, 2015

Page | 6

SCORGTM V5.1, 2015

Inspect the Rotor Profile in the GUI for gaps in the tips, starting points of the profile
indicated by the small yellow circles. Below is the required orientation.

Set Project Units to SI

Set the following Profile Parameters to get correct rotor diameter and center distance:

*Setting GAPI = 0.06 sets the total interlobe clearance as sum of clearance in imported
profiles and the GAPI.
TM

PDM Analysis Ltd, 2015

Page | 7

SCORGTM V5.1, 2015

Go to Geometry Set the following parameters:

Go to Thermodynamics Set the following parameters:

Save the Project.

TM

PDM Analysis Ltd, 2015

Page | 8

SCORGTM V5.1, 2015

3 SCORGTM Mesh Generation

SCORGTM is stand-alone numerical CAD-CFD interface used to generate a numerical mesh
of rotating parts of a screw machine and to transfer it to a general finite volume numerical
solver. The program generates a block structured hexahedral numerical grid for rotor flow
domains, solid rotor domains, inlet and outlet ports.
Inputs Required
In this step the rotor domain mesh is generated in SCORGTM. The inputs required for this
mesh generation are: (Kovacevic, et al., 2007).
Control Parameters:
Type of the machine.
Number of mesh divisions along the lobe in circumferential direction.
Number of mesh divisions in radial direction.
Number of Angular divisions of the rotation.
Control Switches:
These Inputs are used to specify the method used for Rotor Profile Input and the required
mesh calculation options.

Click Grid Module in the project tree

In Mesh Type Size set:
o Circumferential = 50
o Radial = 8
o Angular = 50
o Profile (Rack) Generation - Numerical
In Control Switches set:
o Rotor Boundary Distribution ON
o Rack Boundary Distribution ON
o Leave all other switches OFF

Distribution Parameters:
These inputs are used for adaptation and distribution of the grid points on the boundaries of
the domain and for smoothing of rack (Rack is the curve representing a rotor with infinite
radius which uniquely separates the flow domains of the male and female rotors).

TM

PDM Analysis Ltd, 2015

Page | 9

SCORGTM V5.1, 2015

Meshing Parameters:
Meshing parameters provide control over the distribution of the internal mesh points in each
cross section of the rotors.
Leave at default values both the distribution and meshing parameters can be
changed later

Start Grid Generation through drop down menu, by clicking on the Icon in the
toolbar or typing [ Ctrl + Y ].

Information about the progress of the selected activities in the meshing procedure is
displayed in the output window. Any warning or error and their locations are indicated. If
errors occur, it is important to manually tune the input parameters which will produce a mesh
without errors. Graphically the mesh distribution in each section can be visualized and
checked for any deviation from requirements. The detailed description of methods used for
distribution, adaptation and generation of numerical mesh is available through the Help in the
drop down menu.

TM

PDM Analysis Ltd, 2015

Page | 10

SCORGTM V5.1, 2015

Inspect report and check that there are no distribution warnings listed

Click Distribution Mesh to visually inspect the distribution in each cross section

TM

PDM Analysis Ltd, 2015

Page | 11

SCORGTM V5.1, 2015

In Control Switches Turn OFF Distributions and Turn ON Fluid Rotor Mesh
Calculate Grid

Inspect report and check that there are no grid errors listed

Click Distribution Mesh to visually inspect the grid in each cross section

TM

PDM Analysis Ltd, 2015

Page | 12

SCORGTM V5.1, 2015

In Control Switches Preprocessor Input File select Pumplinx

Set Vertex Files Start = 1
Set Vertex Files End = 1
Calculate Grid

With this the SCORG Project is complete and the Pumplinx setup can be started.
In the directory structure of SCORG Project Grid Output consists of Pumplinx
folder.
Copy files in this folders to the project working directory
TwinScrewPumplinxSetup
These are Rotor grids and the Pumplinx Template Setup

TM

PDM Analysis Ltd, 2015

Page | 13

SCORGTM V5.1, 2015

The highlighted files are required for full setup.

TM

PDM Analysis Ltd, 2015

Page | 14

SCORGTM V5.1, 2015

4 Pumplinx case setup

Launch Pumplinx
Select Open Select [ Setup_Tutorial_Compressor.spro ]

Save as [ TwinScrew35_Compressor.spro ]
Click Screw Module Inspect the Model Properties Correct the speed to
8000rpm.

View Geometric Entities by Type:

TM

PDM Analysis Ltd, 2015

Page | 15

SCORGTM V5.1, 2015

Scan through each of the boundaries and inspect the Properties.

Axial1_male and Axial1_female should form the Suction Interface with Suction
Ports suction_mgi_screw.
Axial2_male and Axial2_female should form the Discharge Axial Interface with the
Discharge Ports discharge_mgi_screw_axi.

TM

PDM Analysis Ltd, 2015

Page | 16

SCORGTM V5.1, 2015

Casing_male, Casing_female, discharge_mgi_screw_rad_1 and
discharge_mgi_screw_rad_2 should form the main interface.
Properties:

This type of interface has been specifically devised for handling screw compressors with
combined Axial and Radial port openings. These could be at the Suction or Discharge. In
the tutorial example the discharge port has a combined axial and radial port.

The variable toln is used to filter only the faces from the rotor casings that form interlobe
areas.

TM

PDM Analysis Ltd, 2015

Page | 17

SCORGTM V5.1, 2015

Rotor_male has following properties inherited by from the Screw Module:

Rotor_female has following properties inherited by from the Screw Module:

TM

PDM Analysis Ltd, 2015

Page | 18

SCORGTM V5.1, 2015

Go to Geometry tree Select Rotor_male and Rotor_female
Go to Results Select Pressure

Create a monitor point at (0.0, 0.062,0.203) for tracking Pressure history

While Point01 is active in the selection, Click Add XY Plot Select Pressure
Plot

TM

PDM Analysis Ltd, 2015

Page | 19

SCORGTM V5.1, 2015

Similarly create Plots for Mass Flux through the suction_inlet and discharge_outlet
boundaries.

Save the project

TM

PDM Analysis Ltd, 2015

Page | 20

SCORGTM V5.1, 2015

5 Pumplinx Solver Calculation

Go to Simulation tab Click Start

The time step size is controlled by the number of divisions used for angular discretization
during grid generation in SCORG.
Monitor the convergence in residuals:

TM

PDM Analysis Ltd, 2015

Page | 21

SCORGTM V5.1, 2015

Pressure contours on the rotor profile can be seen updated by selecting the boundaries
in geometric tree.

6 Summary
This document describes the steps to setup a Pumplinx model for Screw compressor CFD
analysis starting from output data generated by SCORGTM Meshing tool. More detailed
information on using SCORG and Screw compressor mesh generation can be found in user
guide (SCORG, 2015). The Screw Module built in Pumplinx provides a very fast and user
friendly setup procedure. It is possible to make quick changes in the grids and simply update
the model by replacing the grid. The setup can be easily duplicated to users own port grids by
editing the .spro file in an ordinary text editor. More detailed information on using Pumplinx,
Transient simulations and Post-Processing can be found in user guide (Simerics, 2014)

7 Bibliography
Kovacevic, A., Stosic, N. & Smith, I. K., 2007. Screw compressors - Three dimensional
computational fluid dynamics and solid fluid interaction, ISBN 3-540-36302-5. 1 ed. New
York: Springer-Verlag Berlin Heidelberg.
SCORG, 2015. SCORG, User Help Manual, London: City University.
Simerics, 2014. Pumplinx 3.4.6 User Guide, Simerics Inc. s.l.:Simeric.
Stosic, N., Smith, I. K. & Kovacevic, A., 2005. Screw compressors: Mathematical modeling
and performance calculation, ISBN 3540242759. 1 ed. London: Springer.
End of Document
PDM Analysis Ltd
8 Eccleston Close, Barnet, EN4 9EZ, United Kingdom
+44 78 2781 8689; +44 20 3489 9018
[email protected] http://www.pdmanalysis.co.uk

TM

PDM Analysis Ltd, 2015

Page | 22