A-Lok & Cpi Fittings PDF

CPI/A-LOK
Tube Fittings
Catalog 4230/4233
August 2004
CPI/A-LOK Tube Fittings

Introduction
Torque
Parker CPI /A-LOK Instrumentation Tube Fittings are

designed as leak-free connections for process, power and
instrumentation applications. These two ferrule fittings are
manufactured to the highest quality standards and are available in a broad range of sizes, materials and configurations.
Parker CPI/A-LOK tube fittings do not twist the tubing during installation. A-LOK's ferrule design assures that all make
and remake motion is transmitted axially to the tubing. Since
no radial movement of the tubing occurs, the tubing is not
stressed. The mechanical integrity of the tubing is maintained.
Features
No Distortion
The Parker CPI/A-LOK tube fitting has been specifically

designed for use on instrumentation, process and control systems, analysers and environmental equipment employed in
chemical, petroleum, power generating and pulp and paper
plants. The CPI/A-LOK tube fitting has also found extensive
application in other fields where a high quality tube fitting is
required.
In make-up, there is no undue force in an outward direction to

distort the fitting body or ferrules to cause interference
between the ferrules and nut. This assures that the nut will
back-off freely for disassembly and permits a greater number
of easy remakes.
Sealing
Positive, reliable connections with Parker CPI/A-LOK fittings
have been qualified by exhaustive tests and over four decades
of experience in the manufacture of quality tube fittings.
Materials
Parker CPI/A-LOK fittings are available as standard in Heat
Code Traceable, 316 stainless steel. Other standard materials include steel, brass, aluminum, nickel-copper, Hastelloy
C, Alloy 600, Titanium, 6Mo, Incoloy 625 and 825. Straight
fittings are machined from cold finished bar stock and shaped
bodies are machined from close grain forgings. The raw
materials used fully conform to the chemical requirements
listed in Specification Table 1. For nuclear and other critical
applications, stainless steel CPI/A-LOK fittings are readily
available with documented heat code traceability.
Nomenclature
Parker CPI/A-LOK fittings part numbers are constructed
from symbols that identify the size and style of the fitting and
material used.
Assembly, Remake, Gaugeability CPI
/A-LOK
tube fittings, refer to page 74 in the engineering report
section. For gauging of Parker CPI/A-LOK tube fittings, refer to page 74.
Pipe Fittings/Adapters
Pressure Rating & Tubing Selection
Parker CPI/A-LOK tube fittings are available in a wide

variety of ISO and ANSI pipe thread configurations. For a full
line of these fittings, see Catalog 4260.
For working pressures of CPI/A-LOK tube connections,

please see the Instrument Tubing Selection Guide (4200TS), found in the Technical Section of your Parker
Instrumentation Products Process Binder, or the Parker
Instrument Tube Fitting Installation Manual (Bulletin
4200-B4) at the end of this catalog.
In some cases where a male or female pipe thread is the
second end of a Parker CPI/A-LOK fitting, such threads
may be the pressure limiting factor of the tubing system.
Pressure ratings for Pipe Ends are shown on page 78.
Tubing
Parker CPI/A-LOK tube fittings can be used with a wide
variety of tubing materials and a broad range of tube wall
thicknesses. CPI/A-LOK seals equally well on both thin wall
and heavy wall tubing. Tubing and fitting materials should
be selected to be compatible with the fluid media. Due to
thermal expansion characteristics and chemical stability,
the tubing should be of the same material as the fitting.
(The exception is brass fittings and copper tubing.)
Huntsville, Alabama, USA
Barnstaple, UK
2
Parker Hannifin Corporation
CPI /A-LOK Tube Fittings

The Parker CPI/A-LOK fittings consists of precision engineered parts designed to provide secure leak-proof joints capable of
satisfying high pressure, vacuum and vibration applications.
Inch CPI
Inch A-LOK
The Parker Suparcase
back ferrule
provides a strong
mechanical
and anti-vibration hold
on the tube
Dynamic seal
by ferrule on
tube and body
Molybdenum
disulfide coated
nut with fine pitch
threads ensure no
galling
Close tolerance
of nut and body
dimensions for
accurate tube
alignment
Parkers high
quality, silver plated
nut ensures no galling
of body threads
Metric CPI
Deep tube
abutment and
close tolerance of
nut and body for
accurate tube
alignment
Metric A-LOK
Metric identification
shoulder
Metric identification
shoulder
The Parker Suparcase
back ferrule provides
a strong mechanical
and anti-vibration hold
on the tube
Dynamic seal
by ferrule
on tube
and body
Molybdenum
disulfide coated nut
with fine pitch threads
ensure no galling
Pressure seal
by front ferrule
on tube and body
Close tolerance
of nut and
body
dimensions
for accurate tube
alignment
Parkers high quality,

silver plated nut
ensures no galling
of body threads
Pressure seal
by front ferrule on
tube and body
Deep tube abutment

and close tolerance
of nut and body
for accurate tube
alignment
Parker Instrumentation Tube Fittings are supplied complete and ready to use. The ferrule(s) swage onto the tube as it moves
down the body seat creating a pressure/vacuum-tight seal on both tube and body by the interface pressure and surface finish of
mating components. The Parker Suparcase ferrule (back-ferrule) creates a strong mechanical hold on the tube.
WARNING
FAILURE, IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL
INJURY AND PROPERTY DAMAGE.
This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product and/or system options for further investigation by users
having technical expertise. It is important that you analyze all aspects of your application and review the information concerning the product or system in the current product catalog. Due
to the variety of operating conditions and applications for these products or systems, the user, through its own analysis and testing, is solely responsible for making the final selection of
the products and systems and assuring that all performance, safety and warning requirements of the application are met.
The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Parker Hannifin Corporation and its
subsidiaries at any time without notice.
Offer of Sale
The items described in this document are hereby offered for sale by Parker Hannifin Corporation, its subsidiaries or its authorized distributors. This offer and its acceptance are governed
by the provisions stated in the Offer of Sale.
Copyright 2004, Parker Hannifin Corporation. All Rights Reserved.
3

Visual Index
MBZ, FRTN
Female Run
Tee
FBZ, MSCN,
MSCK, MSCR
Male Connnector
Port Connectors
TRBZ, TUR,
TUCM, TURM
Tube End Reducer
page 24
pages 8, 9, 10, 11, 12
OBZ, FBTN
Female
Branch Tee
FH2BZ, MBCN
Male Bulkhead
Connector
page 25
page 13
Tube to Tube Unions
T2H2B2, TUBC
Tube End
Bulkhead
Adapter
HBZ, SC, SCM

Union
ZPC, PC, PCM

Port Connector
page 26
page 14
T2HF, MAN,
MAR, MAK
Tube End
Male Adapter
page 27
pages 38, 39, 40, 41
pages 14, 15, 16
HBZ, RU, RUM

Reducing Union
page 27
VBZ, MVELN
NPT Male 45 Elbow
page 17
WBZ, BC,
BCM
Bulkhead Union
RBZ, MRTN
NPT Male Run Tee
page 28
page 18
DEBTA, DELTA
Dielectric Union
Adapter,
Dielectric
Assembly
SBZ, MBTN
NPT Male
Branch Tee
Tube to Female Pipe
EBZ, EE,
EEM, ELZ
Union Elbow
T2HG, FAN,
FAK, FAR
Tube End
Female Adapter
Tube to O Ring Seal
P2HF
Push-Lok
to Male Adapter
ZHBA, M1SC
Male Connector
SAE Straight
Thread
page 49
C5BZ, M5SEL
Male SAE
Straight Thread
Elbow
page 50
page 45
GH2BZ, FBCN
Female
Bulkhead
Connector
P2BZ6, P2LZ6
Push-Lok to
CPI/A-LOK
JBZ, JLZ
Drop Size
Tee
page 45
page 22
page 32
GBZ, FSC GC
Gauge Connector
KBZ, ECR,
ECRM
Union
Cross
ZP2
Push-Lok to
Port Connector
page 45
BSPP
DBZ, FELN
Female Elbow
page 47
page 47
page 31
pages 22, 23
XHBZ
XASC
37 Flare Connector
to CPI/A-LOK
page 42
page 44
JBZ, ET,
ETM
Union Tee
pages 20, 21
page 47
XH2BZ, XABC
37 Flare
Bulkhead
Connector to
CPI/A-LOK
P2T2, P2TU
Push-Lok
to Tube Adapter
pages 29, 30
GBZ, FSCN,
FSCK
Female Connnector
X6HBZ6, X6TU
37 Flare (AN)
to CPI/A-LOK
T2HOA, TUHA
Tube End to
SAE Straight
Thread Adapter
pages 42, 43, 44
page 29
page 19
37 Flare (AN)
to CPI/A-LOK
page 37
HBZ, CU
Conversion
Union
CBZ, MSELN,
MSELK
Male Elbow
page 46
pages 34, 35, 36
page 36
FH4BZ, MTCN
Thermocouple
Connector
ZH2BZ, ZH2LX
DP Transmitter
Calibration
Adapters
LJFBZ, LJF
Lapped
Joint
Tube Adaptors
page 33
CBZ (R),
MSEL (R)
Male BSPP Straight
Thread Elbow
BSPP
Tube to Male Pipe
page 50
R5BZ,
M5RT
Male Run
Tee SAE
Straight Thread
page 51
page 46
page 23
4

Visual Index
BSPP
RBZ (R),
MRT (R)
Male BSPP
Run Tee
Straight Thread
Z2HCZ, Z2HLZ
Column End Fitting
FHOA
Pipe Thread to
SAE Straight
Thread Adapter
page 51
ZHCZ, ZHLZ
Column End
Fitting
(without Frit)
AH2BZ, AH2LZ
Bulkhead to
Conversion
Adapter
page 64
Z7HBZ7,
Z7HLZ7
Union
Connector
Tube to Welded
Systems
BSPP
page 58
ZH3BA, ZH3LA
Long Male
Connector
SAE Straight
Thread
ZEBW2, ZELW2
Buttweld Elbow
ZHBW2, ZHLW2
Buttweld
Connector
page 55
T2HOF5, M3TU
Tube End to
O Ring Pipe
Thread
page 68
FF, FFM
Front Ferrules
page 69
BF, BFM
Back Ferrules
page 69
Ferrule
Holder
ZHBS, ZHLS
Sanitary
Flange Fitting
page 69
Barbed Fittings
B2HF
Barbed
Connector to
Male Pipe
FNZ, BLP, BLPM

Plug
PNBZ, BLEN,
BLENM Cap
page 70, 71
MDF
Vent Protector
page 71
page 66
Sealing Washers
page 59, 60
B2HT2, B2TU
Barbed
Connector to
Tube Adapter
Analytical Fittings
page 66
Z2HCZ7, Z2HLZ7
Column End
Fitting
HCS
Hose Connector
Sleeve
page 62
page 54
T2HOA5, M2TU
Tube End to
O Ring Straight
Thread
BZP Knurled Nut
page 65
page 65
ZHBW, ZHLW
Socket Weld
Connector
page 53
ZHBF5, M3SC
Male Connector
to O Ring
Pipe Thread
page 68
page 70
page 59
page 54
FBZ7, FLZ7
Male Connector
page 58
V5BZ, M5VEL
45 Positionable
Male Elbow
ZHBA5, M2SC
Male Connector
to O Ring
Straight Thread
page 64
ZEBW, ZELW
Socket Weld
Elbow
page 52
page 53
BZI Inverted
Tube Nut
page 56
page 52
SBZ (R),
MBT (R)
Male BSPP
Branch Tee
Straight Thread
page 68
page 63
page 56
S5BZ, M5BT
Male Branch
Tee SAE
Straight
Thread
TZ Ferrules
page 66
Z3HCZ7, Z3HLZ7
Column End
Fitting
page 72
WLZ, WLN
Bulkhead Locknut
page 73
BN Bulkhead
Locknut
page 73
L5N Accessory
Locknut
page 73
page 62
ZHCZ7, ZHLZ7
Column End
Fitting
(without Frit)
page 63
Components
Engineering Report
page 74
TIZ Insert
page 67
Instrument Tubing Selection

Guide
pages 75-78
BZ, NU, NUM

Tube Nut
Pipe End Pressure Ratings

page 78
page 67, 68
Thread and Tube End Size

Charts (U.S.A/International)
pages 79-81
page 55
5

Table 1 Typical Raw Material Specifications
BASIC FITTING
MATERIAL
BAR STOCK
COMMON TUBING
SPECIFICATION
FORGING
BRASS
CA-360
QQ-B 626 Alloy 360
ASTM-B16 Alloy 360
CA-345
ASTM-B-453 Alloy 345
CA-377
QQ-B 626 Alloy 377
ASTM-B-124 Alloy 377
BS2872 CZ122
ASTM-B75
ASME-SB75
(TEMPER "O")
STAINLESS STEEL
(Type 316)(1)
ASME-SA-479
Type 316-SS
BS970 316-S31
DIN 4401
ASTM A276 Type 316
ASME-SA-182 316
BS970 316-S31
DIN 4401
ASME-SA-213
ASTM-A-213
ASTM-A-249
ASTM-A-269(2)
MIL T-8504
MIL T-8506
STEEL
ASTM-A-108
QQ-S-637
ASTM-A-576
SAE J524b
SAE J525b
ASTM-A-179
ALUMINUM
2017-T4 or 2024-T4
ASTM-B211
QQ-A-225/5 or 6
2014T (as fabricated)

ASTM-B-211
QQ-A-225/4
303, 6061T6
ASTM-B-210
NICKEL-COPPER
ASTM-B-164
QQ-N-281
BS3076 NA13
ASTM-B-164
QQ-N-281
BS3076 NA13
ASTM-B-165
HASTELLOY
C-276
ASTM-B-574
ASTMB575
ASTM-B-574
ASTM-B-622
ASTM-B-626
ALLOY 600
ASTM B-166
ASME-SB-166
ASTM-B-564
ASTM-B-163
CARPENTER 20
ASTM-B-473
ASTM-B-462
ASTM-B-472
ASTM-B-468
TITANIUM
ASTM-B-348
ASTM-B-381
ASTM-B-338
INCOLOY 625
BS3076 NA16
ASTMB425
BS3076 NA16
ASTMB425
ASTM-B-625
ASTM-B-444
ASTM-B-423
ASTM-B-829
UNS S31254
ASTM A479
UNS S31254
ASTM A 479
ASTM-A-269
INCOLOY 825
6MO
(1) If more specific information, including heat code traceability, is required, your Parker Hannifin CPI/A-LOK distributor will provide details.
(2) Stainless steel CPI/A-LOK tube fittings work reliably on both seamless and welded-redrawn, fully annealed type 304, 316 and 316L tubing.
Tube End Dimensional Data

INCHES
INCHES
H
HEX
E
DIA.
D
TUBE
INS.
DEPTH
.43
.60
.64
.70
.73
5/16
7/16
1/2
9/16
5/8
.052
.093
.125
.187
.250
.34
.50
.54
.60
.64
11/16 .281
7/8
.406
1
.500
1-1/8 .625
1-1/4 .750
1-1/2 .875
1-7/8 1.09
2-1/4 1.34
2-3/4 1.81
.67
.90
.96
.96
1.03
1.24
1.61
1.96
2.65
SIZE
NO.
TUBE
O.D.
A-LOK
STRAIGHT
THREAD
1
2
3
4
5
1/16
1/8
3/16
1/4
5/16
10-32
5/16-20
3/8-20
7/16-20
1/2-20
6
8
10
12
14
16
20
24
32
3/8
9/16-20
.76
1/2
3/4-20
.87
5/8
7/8-20
.87
3/4
1-20
.87
7/8 1-1/8-20
.87
1
1-5/16-20 1.05
1-1/4 1-5/8-20 1.52
1-1/2 1-15/16-20 1.77
2
2-5/8-20 2.47
W
HEX
MILLIMETERS
CPI
STRAIGHT
THREAD
H
HEX
A-LOK
STRAIGHT
THREAD
NOTE: Dimensions C and D are shown in the fingertight position.

Average Value
Dimensions for reference only, subject to change.
SIZE
NO.
TUBE
O.D.
A-LOK
STRAIGHT
THREAD
2
3
4
6
8
2mm
3mm
4mm
6mm
8mm
5/16-20
5/16-20
3/8-20
7/16-20
1/2-20
10
12
14
15
16
18
20
22
25
10mm 5/8-20
12mm 3/4-20
14mm 7/8-20
15mm 7/8-20
16mm 7/8-20
18mm
1-20
20mm 1-1/8-20
22mm 1-1/8-20
25mm 1-5/16-20
H
HEX
E
DIA.
D
TUBE
INS.
DEPTH
15,3
15,3
16,1
17,7
18,6
12,0
12,0
12,0
14,0
15,0
1,7
2,4
2,4
4,8
6,4
12,9
12,9
13,7
15,3
16,2
19,5
22,0
22,0
22,0
22,0
22,0
22,0
22,0
26,5
18,0
22,0
24,0
24,0
24,0
27,0
30,0
30,0
35,0
7,9
9,5
11,1
11,9
12,7
15,1
15,9
18,3
21,8
17,2
22,8
24,4
24,4
24,4
24,4
26,0
26,0
31,3
NOTE: Dimensions C and D are shown in the fingertight position.

Average Value
6

Nomenclature
Parker CPI/A-LOK tube fittings part numbers are constructed from symbols that identify the size and style of the fitting and material used.
Example: The part number shown below is for a Parker A-LOK stainless steel male connector for 1/2" O.D. tube (8) and 1/4" male
pipe thread (4).
-
How To Order
CPI Inch Parts
How To Order
A-LOK Inch
Parts
FBZ
SS
1st End
1/2" Tube O.D.
2nd End
1/4 Pipe Thread
Fitting Type
Male Connector
Material
Stainless Steel
MSC
1st End
1/2" Tube O.D.
Fitting Type
Male Connector
2nd End
1/4" Pipe Thread
Thread Type
NPT
316
Material
Stainless Steel
Parker CPI/A-LOK Tube Fittings are ordered by part number as listed in this catalog.
1
Size: Tube and pipe thread sizes are designed by the number of sixteenths of an inch
(1/2" tube = 8/16" = 8). (1/4" pipe thread = 4/16" = 4).
Straights & Elbows: Call out largest CPI/A-LOK tube end size first followed by the smaller CPI/A-LOK tube end
or pipe thread size.
2
Tees & Crosses: For drop size tees first size the run (1 to 2) and then branch (3). Example the size designator
3
for a male run tee for 3/8" O.D. tube and 1/4" male pipe thread would be 6-4-6. For crosses first size the run (1 to
2) and then the branch (3 to 4). For tees with all ends the same, use the tube and size before and after the style des
ignator; i.e. 4-4-4 JBZ (CPI ), 4ET4 (A-LOK ).

Type: A letter or combination of letters and numbers are used to designate the type of fitting. (i.e. SBZ or MBT = male branch tee, GBZ or
FA = female adapter, etc.) See the visual index for fitting types.
Material: Basic material type (B = brass, SS or 316 = stainless steel, type 316; S = steel; A = aluminum; M = Monel; HC = Hastelloy C-276;
IN = Alloy 600; SS20 = Carpenter 20; 6MO = 6Mo; 625 = 625; 825 = 825; T = Titanium). Parker CPI/A-LOK Tube fittings, for special applications, can be furnished in almost any material suitable for machining.
Special Fittings: If there is any question as to the fitting desired, particularly for special fitting configurations, it is suggested that a
customer print be submitted with the fitting request for quote.
Availability: Items priced in current price list 4230/4233 are carried in stock. Price and delivery for non-stocked items quoted on request through
the Quick Response Department.
How To Order
CPI Metric
Parts
How To Order
A-LOK Metric
Parts
GBZ
12
Style
Female Connector
1/4
Tube O.D
12mm
Thread Size
1/4"
BSP
M12
FSC
1/4
Tube O.D.
12mm
Style
Female Connector
Thread Size
1/4"
Thread Type*
NPT
SS
Material
Stainless Steel
-
316
4
Material
Stainless Steel
Parker CPI/A-LOK tube fittings are ordered by part number as listed in this catalog.
Size: Metric tube is designated in millimeters and prefixed M (i.e. 12mm tube = M12.) The pipe thread size is
written as a fraction (i.e. 1/4 NPT = 1/4N).
Straights & Elbows: Call out largest CPI/A-LOK tube end size first followed by the smaller CPI/A-LOK tube end
or pipe thread size.
Tees & Crosses: For drop size tees first size the run (1 to 2) and then branch (3). Example the size designator for a male run tee for 6mm
tube and 1/4" male pipe thread would be 6-4-6. For crosses first size the run (1 to 2) and then the branch (3 to 4). For tees with all ends the
same size, use the tube end size after the style designator; i.e, JBZ 4-4-4 (CPI), ETM4 (A-LOK).
Type: A letter or combination of letters and numbers are used to designate the type of fitting. See the visual index for fitting types.
Material: Basic material type (B = brass, SS or 316 = stainless steel, type 316; S = steel; A = aluminum; M = Monel; HC = Hastelloy C-276;
IN = Alloy 600; SS20 = Carpenter 20; 6MO = 6Mo; 625 = 625; 825 = 825; T = Titanium). Parker CPI/A-LOK Tube fittings, for special applications, can be furnished in almost any material suitable for machining.
Color Coding
Thread types:
N = NPT
K = BSP Taper
R = BSPP
BR = BSPP
M = Metric
R-ED = BSPP
ANSI B1.20.1
BS21, ISO7/1
BS2779, ISO 228/1+2, DIN 3852 FORM A
BS2779, ISO 228/1+2, DIN 3852 FORM B
ISO 6149-2
BS2779, ISO 228/1+2, DIN 3852
with elastic sealing
For easy reference, table heads

are color indicated as follows:
fractional
metric
Please see visual index.

Availability: Items priced in current price list 4230/4233 are carried in stock. Price and delivery for non-stocked items quoted on request through
the Parker IPD Quick Response Department.
NOTE: Hastelloy C-276 is a registered trademark of Cabot Corporation. Carpenter 20 is a registered trademark of Carpenter Technology Corporation.
7
Tube to Male Pipe

FBZ, MSCN
NPT Male
Connector
For fractional tube
A
R
W HEX
D
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
NPT PIPE
THREAD
W
HEX
1-1 FBZ
1-2 FBZ
1-4 FBZ
2-1 FBZ
2-2 FBZ
1MSC1N
1MSC2N
1MSC4N
2MSC1N
2MSC2N
100-1-1
100-1-2
100-1-4
200-1-1
200-1-2
1/16
1/16
1/16
1/8
1/8
1/16
1/8
1/4
1/16
1/8
.93
1.03
1.23
1.17
1.20
.43
.43
.43
.60
.60
.78
.88
1.08
.91
.94
.38
.38
.56
.38
.38
5/16
7/16
9/16
3/8
7/16
2-4 FBZ
2-6 FBZ
2-8 FBZ
3-1 FBZ
3-2 FBZ
2MSC4N
2MSC6N
2MSC8N
3MSC1N
3MSC2N
200-1-4
200-1-6
200-1-8
300-1-1
300-1-2
1/8
1/8
1/8
3/16
3/16
1/4
3/8
1/2
1/16
1/8
1.40
1.42
1.67
1.23
1.23
.60
.60
.60
.64
.64
1.14
1.16
1.41
.97
.97
.56
.56
.75
.38
.38
9/16
11/16
7/8
7/16
7/16
3-4 FBZ
4-1 FBZ
4-2 FBZ
4-4 FBZ
4-6 FBZ
3MSC4N
4MSC1N
4MSC2N
4MSC4N
4MSC6N
300-1-4
400-1-1
400-1-2
400-1-4
400-1-6
3/16
1/4
1/4
1/4
1/4
1/4
1/16
1/8
1/4
3/8
1.43
1.29
1.29
1.49
1.51
.64
.70
.70
.70
.70
1.17
1.00
1.00
1.20
1.22
.56
.38
.38
.56
.56
9/16
1/2
1/2
9/16
11/16
4-8 FBZ
4-12 FBZ
5-2 FBZ
5-4 FBZ
5-6 FBZ
4MSC8N
4MSC12N
5MSC2N
5MSC4N
5MSC6N
400-1-8
400-1-12
500-1-2
500-1-4
500-1-6
1/4
1/4
5/16
5/16
5/16
1/2
3/4
1/8
1/4
3/8
1.76
1.82
1.34
1.52
1.55
.70
.70
.73
.73
.73
1.47
1.53
1.05
1.23
1.25
.75
.75
.38
.56
.56
7/8
1-1/16
9/16
9/16
11/16
5-8 FBZ
6-2 FBZ
6-4 FBZ
6-6 FBZ
6-8 FBZ
5MSC8N
6MSC2N
6MSC4N
6MSC6N
6MSC8N
500-1-8
600-1-2
600-1-4
600-1-6
600-1-8
5/16
3/8
3/8
3/8
3/8
1/2
1/8
1/4
3/8
1/2
1.79
1.38
1.57
1.57
1.82
.73
.76
.76
.76
.76
1.5
1.09
1.28
1.28
1.53
.75
.38
.56
.56
.75
7/8
5/8
5/8
11/16
7/8
6-12 FBZ
8-2 FBZ
8-4 FBZ
8-6 FBZ
8-8 FBZ
6MSC12N
8MSC2N
8MSC4N
8MSC6N
8MSC8N
600-1-12
810-1-2
810-1-4
810-1-6
810-1-8
3/8
1/2
1/2
1/2
1/2
3/4
1/8
1/4
3/8
1/2
1.88
1.53
1.71
1.71
1.93
.76
.87
.87
.87
.87
1.59
1.13
1.31
1.31
1.53
.75
.38
.56
.56
.75
1-1/16
13/16
13/16
13/16
7/8
8-12 FBZ
8-16 FBZ
10-6 FBZ
10-8 FBZ
10-12 FBZ
8MSC12N
8MSC16N
10MSC6N
10MSC8N
10MSC12N
810-1-12
810-1-16
1010-1-6
1010-1-8
1010-1-12
1/2
1/2
5/8
5/8
5/8
3/4
1
3/8
1/2
3/4
1.99
2.28
1.74
1.93
1.99
.87
.87
.87
.87
.87
1.59
1.88
1.34
1.53
1.59
.75
.94
.56
.75
.75
1-1/16
1-3/8
15/16
15/16
1-1/16
12-8 FBZ
12-12 FBZ
12-16 FBZ
14-12 FBZ
14-16 FBZ
12MSC8N
12MSC12N
12MSC16N
14MSC12N
14MSC16N
1210-1-8
1210-1-12
1210-1-16
1410-1-12
1410-1-16
3/4
3/4
3/4
7/8
7/8
1/2
3/4
1
3/4
1
1.99
1.99
2.28
1.99
2.28
.87
.87
.87
.87
.87
1.59
1.59
1.88
1.59
1.88
.75
.75
.94
.75
.94
1-1/16
1-1/16
1-3/8
1-3/16
1-3/8
16-8 FBZ
16-12 FBZ
16-16 FBZ
20-20 FBZ
24-24 FBZ
32-32 FBZ
16MSC8N
16MSC12N
16MSC16N
20MSC20N
24MSC24N
32MSC32N
1610-1-8
1610-1-12
1610-1-16
2010-1-20
2410-1-24
3210-1-32
1
1
1
1-1/4
1-1/2
2
1/2
3/4
1
1-1/4
1-1/2
2
2.27
2.27
2.46
3.03
3.50
4.47
1.05
1.05
1.05
1.52
1.77
2.47
1.78
1.78
1.97
2.17
2.44
3.00
.75
.75
.94
.97
1.00
1.04
1-3/8
1-3/8
1-3/8
1-3/4
2-1/8
2-3/4
NOTE: A and C dimensions are typical finger-tight.
Sizes 20, 24, 32 require additional lubrication to assembly.
Color Coding
For easy reference, table heads
are color indicated as follows:
fractional
metric
8
Tube to Male Pipe

FBZ, MSCN
NPT Male
Connector
For metric tube
A
R
W HEX
D
MILLIMETERS
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
NPT PIPE
THREAD
W
HEX
FBZ 2-1/8
FBZ 3-1/8
FBZ 3-1/4
FBZ 4-1/8
FBZ 4-1/4
M2MSC1/8N
M3MSC1/8N
M3MSC1/4N
M4MSC1/8N
M4MSC1/4N
2MO-1-2
3MO-1-2
3MO-1-4
4MO-1-2
4MO-1-4
2
3
3
4
4
1/8
1/8
1/4
1/8
1/4
29,7
29,7
35,3
31,2
36,3
15,3
15,3
15,3
16,1
16,1
23,1
23,1
28,7
24,6
29,7
9,5
9,5
14,3
9,5
14,3
12,0
12,0
14,0
12,0
14,0
FBZ 6-1/8
FBZ 6-1/4
FBZ 6-3/8
FBZ 6-1/2
FBZ 8-1/8
M6MSC1/8N
M6MSC1/4N
M6MSC3/8N
M6MSC1/2N
M8MSC1/8N
6MO-1-2
6MO-1-4
6MO-1-6
6MO-1-8
8MO-1-2
6
6
6
6
8
1/8
1/4
3/8
1/2
1/8
32,9
38,1
38,5
44,8
34,2
17,7
17,7
17,7
17,7
18,6
25,4
30,6
31,0
37,3
26,7
9,5
14,3
14,3
19,1
9,5
14,0
14,0
18,0
22,0
15,0
FBZ 8-1/4
FBZ 8-3/8
FBZ 8-1/2
FBZ 10-1/8
FBZ 10-1/4
M8MSC1/4N
M8MSC3/8N
M8MSC1/2N
M10MSC1/8N
M10MSC1/4N
8MO-1-4
8MO-1-6
8MO-1-8
10MO-1-2
10MO-1-4
8
8
8
10
10
1/4
3/8
1/2
1/8
1/4
38,8
39,3
45,6
36,1
40,9
18,6
18,6
18,6
19,5
19,5
31,3
31,8
38,1
28,6
33,3
14,3
14,3
19,1
9,5
14,3
15,0
18,0
22,0
18,0
18,0
FBZ 10-3/8
FBZ 10-1/2
FBZ 10-3/4
FBZ 10-1
FBZ 12-1/4
M10MSC3/8N
M10MSC1/2N
M10MSC3/4N
M10MSC1N
M12MSC1/4N
10MO-1-6
10MO-1-8
10MO-1-12
10MO-1-16
12MO-1-4
10
10
10
10
12
3/8
1/2
3/4
1
1/4
40,9
47,5
46,4
55,0
43,4
19,5
19,5
19,5
19,5
22,0
33,3
38,9
38,9
47,5
33,3
14,3
19,1
19,1
23,8
14,3
18,0
22,0
27,0
35,0
22,0
FBZ 12-3/8
FBZ 12-1/2
FBZ 12-3/4
FBZ 14-1/4
FBZ 14-3/8
M12MSC3/8N
M12MSC1/2N
M12MSC3/4N
M14MSC1/4N
M14MSC3/8N
12MO-1-6
12MO-1-8
12MO-1-12
14MO-1-4
14MO-1-6
12
12
12
14
14
3/8
1/2
3/4
1/4
3/8
43,4
49,0
50,5
44,2
44,2
22,0
22,0
22,0
22,0
22,0
33,3
38,9
40,4
34,1
34,1
14,3
19,1
19,1
14,3
14,3
22,0
22,0
27,0
24,0
24,0
FBZ 14-1/2
FBZ 15-1/2
FBZ 16-3/8
FBZ 16-1/2
FBZ 16-3/4
M14MSC1/2N
M15MSC1/2N
M16MSC3/8N
M16MSC1/2N
M16MSC3/4N
14MO-1-8
15MO-1-8
16MO-1-6
16MO-1-8
16MO-1-12
14
15
16
16
16
1/2
1/2
3/8
1/2
3/4
49,0
49,0
44,1
49,0
50,5
22,0
22,0
22,0
22,0
22,0
38,9
38,9
34,01
38,9
40,5
19,1
19,1
14,3
19,1
19,1
24,0
24,0
24,0
24,0
27,0
FBZ 18-1/2
FBZ 18-3/4
FBZ 20-1/2
FBZ 20-3/4
FBZ 20-1
M18MSC1/2N
M18MSC3/4N
M20MSC1/2N
M20MSC3/4N
M20MSC1N
18MO-1-8
18MO-1-12
20MO-1-8
20MO-1-12
20MO-1-16
18
18
20
20
20
1/2
3/4
1/2
3/4
1
50,6
50,6
50,6
52,3
57,7
22,0
22,0
22,0
22,0
22,0
40,5
40,5
42,2
42,2
47,6
19,1
19,1
19,1
19,1
23,8
27,0
27,0
30,0
30,0
35,0
FBZ 22-3/4
FBZ 24-1/2
FBZ 25-3/4
FBZ 25-1
M22MSC3/4N
M25MSC1/2N
M25MSC3/4N
M25MSC1N
22MO-1-12
25MO-1-8
25MO-1-12
25MO-1-16
22
25
25
25
3/4
1/2
3/4
1
52,3
57,5
57,5
62,3
22,0
26,5
26,5
26,5
42,2
45,3
45,2
50,0
19,1
19,1
19,1
23,8
35,0
35,0
35,0
35,0
9
Tube to Male Pipe

FBZ, MSCK
BSP Taper Male
Connector
For fractional tube
BSP
A
R
BSP
W HEX
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
BSPT
THREAD
W
HEX
BORE
2-2K FBZ
2-4K FBZ
4-2K FBZ
4-4K FBZ
4-6K FBZ
4-8K FBZ
2MSC2K
2MSC4K
4MSC2K
4MSC4K
4MSC6K
4MSC8K
200-1-2RT
200-1-4RT
400-1-2RT
400-1-4RT
400-1-6RT
400-1-8RT
1/8
1/8
1/4
1/4
1/4
1/4
1/8
1/4
1/8
1/4
3/8
1/2
1.20
1.40
1.30
1.50
1.52
1.77
.60
.60
.70
.70
.70
.70
.938
1.14
1.00
1.20
1.22
1.47
.38
.56
.38
.56
.56
.75
7/16
9/16
1/2
9/16
11/16
7/8
.19
.19
.19
.19
.19
.19
5-2K FBZ
5-4K FBZ
6-2K FBZ
6-4K FBZ
6-6K FBZ
5MSC2K
5MSC4K
6MSC2K
6MSC4K
6MSC6K
500-1-2RT
500-1-4RT
600-1-2RT
600-1-4RT
600-1-6RT
5/16
5/16
3/8
3/8
3/8
1/8
1/4
1/8
1/4
3/8
1.34
1.52
1.39
1.57
1.57
.73
.73
.76
.76
.76
1.05
1.23
1.09
1.28
1.28
.38
.56
.38
.56
.56
9/16
9/16
5/8
5/8
11/16
.19
.19
.19
.28
.28
6-8K FBZ
8-4K FBZ
8-6K FBZ
8-8K FBZ
6MSC8K
8MSC4K
8MSC6K
8MSC8K
600-1-8RT
810-1-4RT
810-1-6RT
810-1-8RT
3/8
1/2
1/2
1/2
1/2
1/4
3/8
1/2
1.82
1.69
1.69
1.91
.76
.86
.86
.66
1.53
1.31
1.31
1.53
.75
.56
.56
.75
7/8
13/16
13/16
7/8
.28
.28
.38
.41
FBZ, MSCK
BSP Taper Male
Connector
For metric tube
MILLIMETERS
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
BSPT
THREAD
W
HEX
FBZ 2-1/8K
FBZ 3-1/8K
FBZ 3-1/4K
FBZ 4-1/8K
FBZ 4-1/4K
M2MSC1/8K
M3MSC1/8K
M3MSC1/4K
M4MSC1/8K
M4MSC1/4K
2MO-1-2RT
3MO-1-2RT
3MO-1-4RT
4MO-1-2RT
4MO-1-4RT
2
3
3
4
4
1/8
1/8
1/4
1/8
1/4
29,7
29,7
35,3
31,2
36,3
15,3
15,3
15,3
16,1
16,1
23,1
23,1
28,7
24,6
29,7
9,5
9,7
14,2
9,7
14,2
12,0
12,0
14,0
12,0
14,0
FBZ 6-1/8K
FBZ 6-1/4K
FBZ 6-3/8K
FBZ 6-1/2K
FBZ 8-1/8K
M6MSC1/8K
M6MSC1/4K
M6MSC3/8K
M6MSC1/2K
M8MSC1/8K
6MO-1-2RT
6MO-1-4RT
6MO-1-6RT
6MO-1-8RT
8MO-1-2RT
6
6
6
6
8
1/8
1/4
3/8
1/2
1/8
32,9
40,0
38,5
45,6
33,9
17,7
17,7
17,7
17,7
18,6
25,4
30,5
31,0
38,1
26,4
9,7
14,2
14,2
19,1
9,5
14,0
14,0
18,0
22,0
15,0
FBZ 8-1/4K
FBZ 8-3/8K
FBZ 8-1/2K
FBZ 10-1/8K
FBZ 10-1/4K
M8MSC1/4K
M8MSC3/8K
M8MSC1/2K
M10MSC1/8K
M10MSC1/4K
8MO-1-4RT
8MO-1-6RT
8MO-1-8RT
10MO-1-2RT
10MO-1-4RT
8
8
8
10
10
1/4
3/8
1/2
1/8
1/4
38,7
39,3
45,6
36,2
40,9
18,6
18,6
18,6
19,5
19,5
31,2
31,8
38,1
28,6
33,3
14,2
14,2
19,1
9,5
14,2
15,0
18,0
22,0
18,0
18,0
FBZ 10-3/8K
FBZ 10-1/2K
FBZ 12-1/4K
FBZ 12-3/8K
FBZ 12-1/2K
M10MSC3/8K
M10MSC1/2K
M12MSC1/4K
M12MSC3/8K
M12MSC1/2K
10MO-1-6RT
10MO-1-8RT
12MO-1-4RT
12MO-1-6RT
12MO-1-8RT
10
10
12
12
12
3/8
1/2
1/4
3/8
1/2
40,9
46,5
43,4
43,4
49,0
19,5
19,5
22,0
22,0
22,0
33,3
38,9
33,3
33,3
38,9
14,2
19,1
14,2
14,2
19,1
18,0
22,0
22,0
22,0
22,0
FBZ 12-3/4K
FBZ 15-1/2K
FBZ 16-3/8K
FBZ 16-1/2K
FBZ 16-3/4K
M12MSC3/4K
M15MSC1/2K
M16MSC3/8K
M16MSC1/2K
M16MSC3/4K
12MO-1-12RT
15MO-1-8RT
16MO-1-6RT
16MO-1-8RT
16MO-1-12RT
12
15
16
16
16
3/4
1/2
3/8
1/2
3/4
49,5
49,0
44,2
49,0
49,5
22,0
22,0
22,0
22,0
22,0
40,4
38,9
34,1
38,9
40,5
19,1
19,1
14,2
19,1
19,1
27,0
24,0
24,0
24,0
27,0
FBZ 18-1/2K
FBZ 18-3/4K
FBZ 20-1/2K
FBZ 20-3/4K
FBZ 22-3/4K
M18MSC1/2K
M18MSC3/4K
M20MSC1/2K
M20MSC3/4K
M22MSC3/4K
18MO-1-8RT
18MO-1-12RT
20MO-1-8RT
20MO-1-12RT
22MO-1-12RT
18
18
20
20
22
1/2
3/4
1/2
3/4
3/4
50,6
50,6
52,3
52,3
52,3
22,0
22,0
22,0
22,0
22,0
40,4
40,4
42,2
42,2
42,2
19,1
19,1
19,1
19,1
19,1
27,0
27,0
30,0
30,0
30,0
FBZ 25-3/4K M25MSC3/4K

FBZ 25-1K
M25MSC1K
25MO-1-12RT
25MO-1-16RT
25
25
3/4
1
57,5
62,3
26,5
26,5
45,2
50,0
19,1
23,9
35,0
35,0
BSP
CPI
PART NO.
A
R
BSP
W HEX
D
10
Tube to Male Pipe

FBZ, MSCR
BSPP Male
Connector
For fractional tube
BSPP
A
R
BSPP
W HEX
D
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
BSPP
THREAD
2-2R FBZ
2-4R FBZ
2-6R FBZ
4-2R FBZ
4-4R FBZ
2MSC2R
2MSC4R
2MSC6R
4MSC2R
4MSC4R
200-1-2RS
200-1-4RS
200-1-6RS
400-1-2RS
400-1-4RS
1/8
1/8
1/8
1/4
1/4
1/8
1/4
3/8
1/8
1/4
1.18
1.27
1.46
1.28
1.49
.60
.60
.60
.70
.70
.922
1.13
1.172
.98
1.19
4-6R FBZ
4-8R FBZ
6-2R FBZ
6-4R FBZ
6-6R FBZ
4MSC6R
4MSC8R
6MSC2R
6MSC4R
6MSC6R
400-1-6RS
400-1-8RS
600-1-2RS
600-1-4RS
600-1-6RS
1/4
1/4
3/8
3/8
3/8
3/8
1/2
1/8
1/4
3/8
1.55
1.77
1.35
1.54
1.57
.70
.70
.76
.76
.76
6-8R FBZ
8-4R FBZ
8-6R FBZ
8-8R FBZ
12-8R FBZ
6MSC8R
8MSC4R
8MSC6R
8MSC8R
12MSC8R
600-1-8RS
810-1-4RS
810-1-6RS
810-1-8RS
1210-1-8RS
3/8
1/2
1/2
1/2
3/4
1/2
1/4
3/8
1/2
1/2
1.82
1.66
1.69
1.91
1.93
12-12R FBZ
16-8R FBZ
16-16R FBZ
12MSC12R
16MSC8R
16MSC16R
1210-1-12RS
1610-1-8RS
1610-1-16RS
3/4
1
1
3/4
1/2
1
2.07
2.21
2.35
W
HEX
BORE
.28
.44
.44
.28
.44
.54
.70
.86
.54
.70
9/16
3/4
7/8
9/16
3/4
.16
.09
.28
.16
.19
1.25
1.47
1.06
1.25
1.28
.44
.56
.28
.44
.44
.86
1.01
.54
.70
.86
7/8
1-1/16
5/8
3/4
7/8
.19
.19
.16
.25
.28
.76
.86
.86
.86
.86
1.53
1.28
1.31
1.53
1.531
.56
.44
.44
.56
.56
1.01
.70
.86
1.01
1.01
1-1/16
13/16
7/8
1-1/16
1-1/16
.28
.25
.31
.41
.41
.86
1.04
1.04
1.69
1.719
1.88
.63
.56
.72
1.25
1.01
1.52
1-3/8
1-3/8
1-5/8
.63
.41
.88

Sealing washer must be used with BSPP end shown ISO228/1 (Form A). see p.72
For Form B undercut change part number and add B before R. e.g. M6MSC1/4BR.
FBZ, MSCR
BSPP Male
Connector
For metric tube
BSPP
A
R
BSPP
W HEX
D
MILLIMETERS
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
BSPP
THREAD
W
HEX
FBZ 2-1/8R
FBZ 3-1/8R
FBZ 3-1/4R
FBZ 6-1/8R
FBZ 6-1/4R
M2MSC1/8R
M3MSC1/8R
M3MSC1/4R
M6MSC1/8R
M6MSC1/4R
2MO-1-2RS
3MO-1-2RS
3MO-1-4RS
6MO-1-2RS
6MO-1-4RS
2
3
3
6
6
1/8
1/8
1/4
1/8
1/4
28,4
30,0
35,3
32,5
37,7
15,3
15,3
15,3
17,7
17,7
21,8
23,4
28,7
25,0
30,2
7,1
7,1
11,2
7,1
11,2
14,0
13,7
17,8
13,7
17,8
13,7
14,0
19,0
14,0
19,0
FBZ 6-3/8R
FBZ 6-1/2R
FBZ 8-1/8R
FBZ 8-1/4R
FBZ 8-3/8R
M6MSC3/8R
M6MSC1/2R
M8MSC1/8R
M8MSC1/4R
M8MSC3/8R
6MO-1-6RS
6MO-1-8RS
8MO-1-2RS
8MO-1-4RS
8MO-1-6RS
6
6
8
8
8
3/8
1/2
1/8
1/4
3/8
39,0
45,6
33,1
38,5
39,8
17,7
17,7
18,6
18,6
18,6
31,5
38,1
25,6
31,0
32,3
11,2
14,2
7,1
11,2
11,2
21,8
25,7
15,0
17,8
21,8
22,0
27,0
13,7
19,0
22,0
FBZ 8-1/2R
FBZ 10-1/4R
FBZ 10-3/8R
FBZ 10-1/2R
FBZ 12-1/4R
M8MSC1/2R
M10MSC1/4R
M10MSC3/8R
M10MSC1/2R
M12MSC1/4R
8MO-1-8RS
10MO-1-4RS
10MO-1-6RS
10MO-1-8RS
12MO-1-4RS
8
10
10
10
12
1/2
1/4
3/8
1/2
1/4
45,6
39,4
40,6
46,5
42,6
18,6
19,5
19,5
19,5
22,0
38,1
31,8
33,0
38,9
32,5
14,2
11,2
11,2
14,2
11,2
25,7
17,8
21,8
25,7
17,8
27,0
19,0
22,0
27,0
22,0
FBZ 12-3/8R
FBZ 12-1/2R
FBZ 12-3/4R
FBZ 16-3/8R
FBZ 16-1/2R
M12MSC3/8R 12MO-1-6RS
12
12
12
16
16
3/8
1/2
3/4
3/8
1/2
43,1
49,0
52,8
43,5
49,0
22,0
22,0
22,0
22,0
22,0
33,0
38,9
42,7
33,4
38,9
11,2
14,2
16,0
11,2
14,2
21,8
25,7
31,8
22,0
26,0
22,0
27,0
35,0
21,8
27,0
FBZ 18-1/2R
FBZ 18-3/4R
FBZ 20-1/2R
FBZ 20-3/4R
FBZ 22-3/4R
M18MSC1/2R
M18MSC3/4R
M20MSC1/2R
M20MSC3/4R
M22MSC3/4R
18MO-1-8RS
18MO-1-12RS
20MO-1-8RS
20MO-1-12RS
22MO-1-12RS
18
18
20
20
22
1/2
3/4
1/2
3/4
3/4
49,0
53,1
50,5
52,8
52,8
22,0
22,0
22,0
22,0
22,0
38,9
43,0
40,4
42,7
42,7
14,2
16,0
14,2
16,0
16,0
26,0
35,0
30,0
32,0
32,0
27,0
32,0
25,7
35,0
35,0
FBZ 25-3/4R M25MSC3/4R 25MO-1-12RS

FBZ 25-1R
M25MSC1R 25MO-1-16RS
25
25
3/4
1
59,8
60,1
26,5
26,5
47,6
47,8
16,0
18,3
35,0
39,0
31,8
41,0
CPI
PART NO.

Sealing washer must be used with BSPP end shown ISO228/1 (Form A). see p.72
For Form B undercut, add a B before the R. e.g. M6MSC1/4BR.
11
Tube to Male Pipe

FBZ, MSCR
BSPP Male
Connector with
ED seal
For fractional tube
CPI
PART NO.
A-LOK
PART NO.
4-4R-ED FBZ
4-8R-ED FBZ
6-6R-ED FBZ
8-4R-ED FBZ
8-6R-ED FBZ
4MSC4R-ED
4MSC8R-ED
6MSC6R-ED
8MSC4R-ED
8MSC6R-ED
8-8R-ED FBZ
8MSC8R-ED
12-12R-ED FBZ 12MSC12R-ED
W
HEX
BORE
1/4
1/4
3/8
1/2
1/2
1/4
1/2
3/8
1/4
3/8
1.48
1.76
1.60
1.69
1.69
.70
.70
.76
.86
.86
1.19
1.38
1.31
1.31
1.31
.47
.55
.47
.47
.47
.74
1.04
.86
.74
.86
3/4
1-1/16
7/8
13/16
7/8
.19
.19
.28
.25
.31
1/2
3/4
1/2
3/4
1.85
1.98
.86
.86
1.47
1.59
.55
.63
1.04
1.25
1-1/16
1-5/16
.41
.63

ED fittings are supplied with sealing washers in Buna-N as standard, suitable for temperatures of between 35C and +100C
(31F to +212F). Viton seals are available upon request which are suitable for temperatures of between 25C and +120C
(13F to +248F).
A
R
INCHES
INTERCHANGES TUBE BSPP

WITH
O.D. THREAD
W HEX
D
FBZ, MSCR
Male Connector
with ED seal
For metric tube
A
R
MILLIMETERS
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
BSPP
THREAD
W
HEX
FBZ6-1/8R-ED
FBZ6-1/4R-ED
FBZ6-3/8R-ED
FBZ6-1/2R-ED
FBZ10-1/4R-ED
M6MSC1/8R-ED
M6MSC1/4R-ED
M6MSC3/8R-ED
M6MSC1/2R-ED
M10MSC1/4R-ED
6
6
6
6
10
1/8
1/4
3/8
1/2
1/4
32,5
38,2
39,5
44,5
40,0
17,7
17,7
17,7
17,7
19,5
25,0
30,7
32,0
37,0
32,3
7,9
11,9
11,9
14,0
11,9
13,7
18,8
21,8
26,4
18,8
14,0
19,0
22,0
27,0
19,0
FBZ10-3/8R-ED
FBZ10-1/2R-ED
FBZ12-1/4R-ED
FBZ12-3/8R-ED
FBZ12-1/2R-ED
M10MSC3/8R-ED
M10MSC1/2R-ED
M12MSC1/4R-ED
M12MSC3/8R-ED
M12MSC1/2R-ED
10
10
12
12
12
3/8
1/2
1/4
3/8
1/2
41,1
46,0
43,1
43,6
48,5
19,5
19,5
22,0
22,0
22,0
38,1
38,4
33,0
33,5
38,4
11,9
14,0
11,9
11,9
14,0
21,8
26,4
18,8
21,8
26,4
22,0
27,0
22,0
22,0
27,0

ED fittings are supplied with sealing washers in Buna-N as standard, suitable for temperatures of between 35C and +100C
(31F to +212F). Viton seals are available upon request which are suitable for temperatures of between 25C and +120C
(13F to +248F).
W HEX
D
12
Tube to Male Pipe

FH2BZ, MBCN
NPT Male
Bulkhead
Connector
For fractional tube
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
1-1 FH2BZ
1-2 FH2BZ
2-2 FH2BZ
3-2 FH2BZ
4-2 FH2BZ
1MBC1N
1MBC2N
2MBC2N
3MBC2N
4MBC2N
100-11-1
100-11-2
200-11-2
300-11-2
400-11-2
1/16
1/16
1/8
3/16
1/4
1/16
1/8
1/8
1/8
1/8
1.19
1.27
1.83
1.89
1.95
.68
.68
1.23
1.26
1.31
1.038
1.116
1.571
1.634
1.655
.53
.53
.97
1.00
1.02
.38
.38
.38
.38
.38
5/16
7/16
1/2
9/16
5/8
4-4 FH2BZ
4-6 FH2BZ
4-8 FH2BZ
5-2 FH2BZ
5-4 FH2BZ
4MBC4N
4MBC6N
4MBC8N
5MBC2N
5MBC4N
400-11-4
400-11-6
400-11-8
500-11-2
500-11-4
1/4
1/4
1/4
5/16
5/16
1/4
3/8
1/2
1/8
1/4
2.132
2.162
2.374
2.08
2.27
1.31
1.31
1.31
1.42
1.42
1.842
1.872
2.084
1.779
1.966
1.02
1.02
1.02
1.12
1.12
.56
.56
.75
.38
.56
5/8
11/16
7/8
11/16
11/16
6-2 FH2BZ
6-4 FH2BZ
6-6 FH2BZ
6-8 FH2BZ
8-4 FH2BZ
6MBC2N
6MBC4N
6MBC6N
6MBC8N
8MBC4N
600-11-2
600-11-4
600-11-6
600-11-8
810-11-4
3/8
3/8
3/8
3/8
1/2
1/8
1/4
3/8
1/2
1/4
2.08
2.265
2.265
2.48
2.494
1.44
1.44
1.44
1.44
1.65
1.788
1.975
1.975
2.219
2.094
1.15
1.15
1.15
1.15
1.25
.38
.56
.56
.75
.56
3/4
3/4
3/4
7/8
15/16
8-6 FH2BZ
8-8 FH2BZ
8-12 FH2BZ
10-6 FH2BZ
10-8 FH2BZ
8MBC6N
8MBC8N
8MBC12N
10MBC6N
10MBC8N
810-11-6
810-11-8
810-11-12
1010-11-6
1010-11-8
1/2
1/2
1/2
5/8
5/8
3/8
1/2
3/4
3/8
1/2
2.494
2.712
2.722
2.628
2.816
1.65
1.65
1.65
1.68
1.68
2.094
2.312
2.322
2.228
2.416
1.25
1.25
1.25
1.28
1.28
.56
.75
.75
.56
.75
15/16
15/16
1-1/8
1-1/16
1-1/16
12-8 FH2BZ
12-12 FH2BZ
14-12 FH2BZ
16-12 FH2BZ
16-16 FH2BZ
12MBC8N
12MBC12N
14MBC12N
16MBC12N
16MBC16N
1210-11-8
1210-11-12
1410-11-12
1610-11-12
1610-11-16
3/4
3/4
7/8
1
1
1/2
3/4
3/4
3/4
1
3.00
3.00
3.31
3.54
3.72
1.87
1.87
2.09
2.27
2.27
2.601
2.601
2.913
3.006
3.194
1.47
1.47
1.69
1.78
1.78
.75
.75
.75
.75
.94
1-3/16
1-3/16
1-3/8
1-5/8
1-5/8
TUBE
O.D.
NPT PIPE
THREAD
W
HEX
A
C
L
W HEX
D

For bulkhead hole drill size and maximum bulkhead thickness, see Page 28, Part BC.
FH2BZ, MBCN
NPT Male
Bulkhead
Connector
For metric tube
A
C
L
MILLIMETERS
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE NPT
O.D. THREAD
W
HEX
BHEAD
HOLE MAX.
DRILL BHEAD
SIZE THICK.
FH2BZ 6-1/8
FH2BZ 6-1/4
FH2BZ 8-1/8
FH2BZ 8-1/4
FH2BZ 10-1/4
M6MBC1/8N 6MO-11-2
M6MBC1/4N 6MO-11-4
M8MBC1/8N 8MO-11-2
M8MBC1/4N 8MO-11-4
M10MBC1/4N 10MO-11-4
6
6
8
8
10
1/8
1/4
1/8
1/4
1/4
49,6
53,5
52,3
57,5
58,4
33,7
33,7
36,0
36,0
37,0
42,1
46,0
44,8
50,0
50,8
26,2
26,2
28,5
28,5
29,4
9,5
14,3
9,5
14,3
14,3
16,0
16,0
18,0
18,0
22,0
11,5
11,5
13,1
13,1
16,3
10,2
10,2
11,2
11,2
11,2
FH2BZ 10-3/8
FH2BZ 10-1/2
FH2BZ 12-1/4
FH2BZ 12-3/8
FH2BZ 12-1/2
M10MBC3/8N
M10MBC1/2N
M12MBC1/4N
M12MBC3/8N
M12MBC1/2N
10
10
12
12
12
3/8
1/2
1/4
3/8
1/2
58,4
63,1
63,3
64,5
67,5
37,0
37,0
10,1
10,1
10,1
50,8
55,5
53,2
54,4
57,4
29,4
29,4
31,8
31,8
31,8
14,3
19,0
14,3
14,3
19,0
22,0
22,0
24,0
24,0
24,0
16,3
16,3
19,5
19,5
19,5
11,2
11,2
12,7
12,7
12,7
10MO-11-6
10MO-11-8
12MO-11-4
12MO-11-6
12MO-11-8
W HEX
D
13
Tube to Male Pipe

FH4BZ, MTCN
Thermocouple
Connector
For fractional tube
A
C
INCHES
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
NPT PIPE
THREAD
1-1 FH4BZ
1-2 FH4BZ
1-4 FH4BZ
2-1 FH4BZ
2-2 FH4BZ
2-4 FH4BZ
1MTC1N
1MTC2N
1MTC4N
2MTC1N
2MTC2N
2MTC4N
100-1-1BT
100-1-2BT
100-1-4BT
200-1-1BT
200-1-2BT
200-1-4BT
1/16
1/16
1/16
1/8
1/8
1/8
1/16
1/8
1/4
1/16
1/8
1/4
.93
1.03
1.23
1.17
1.20
1.40
3-2 FH4BZ
3-4 FH4BZ
4-2 FH4BZ
4-4 FH4BZ
4-6 FH4BZ
3MTC2N
3MTC4N
4MTC2N
4MTC4N
4MTC6N
300-1-2BT
300-1-4BT
400-1-2BT
400-1-4BT
400-1-6BT
3/16
3/16
1/4
1/4
1/4
1/8
1/4
1/8
1/4
3/8
4-8 FH4BZ
5-4 FH4BZ
6-4 FH4BZ
6-6 FH4BZ
6-8 FH4BZ
4MTC8N
5MTC4N
6MTC4N
6MTC6N
6MTC8N
400-1-8BT
500-1-4BT
600-1-4BT
600-1-6BT
600-1-8BT
1/4
5/16
3/8
3/8
3/8
6-12 FH4BZ
6MTC12N
8-8 FH4BZ
8MTC8N
8-12 FH4BZ
8MTC12N
10-12 FH4BZ 10MTC12N
600-1-12BT
810-1-8BT
810-1-12BT
1010-1-12BT
1210-1-12BT
1610-1-16BT
CPI
PART NO.
W
HEX
.43
.43
.43
.60
.60
.60
.78
.88
1.08
.91
.94
1.14
.38
.38
.56
.38
.38
.56
5/16
7/16
9/16
3/8
7/16
9/16
1.23
1.43
1.29
1.49
1.60
.64
.64
.70
.70
.70
.97
1.17
1.00
1.20
1.22
.38
.56
.38
.56
.56
7/16
9/16
1/2
9/16
11/16
1/2
1/4
1/4
3/8
1/2
1.87
1.52
1.57
1.57
1.82
.70
.73
.76
.76
.76
1.47
1.22
1.28
1.28
1.53
.75
.56
.56
.56
.75
7/8
9/16
5/8
11/16
7/8
3/8
1/2
1/2
5/8
3/4
3/4
1/2
3/4
3/4
3/4
1.88
1.93
1.99
1.99
1.99
.76
.87
.87
.87
.87
1.59
1.53
1.59
1.59
1.59
.75
.76
.75
.75
.75
1-1/16
7/8
1-1/16
1-1/16
1-1/16
2.46
1.05
1.97
.94
1-3/8
W HEX
D
CBZ, MSELN
NPT Male Elbow
For fractional tube
C
L
W HEX
H
R
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
NPT PIPE
THREAD
1-1 CBZ
1-2 CBZ
2-1 CBZ
2-2 CBZ
2-4 CBZ
3-2 CBZ
1MSEL1N
1MSEL2N
2MSEL1N
2MSEL2N
2MSEL4N
3MSEL2N
100-2-1
100-2-2
200-2-1
200-2-2
200-2-4
300-2-2
1/16
1/16
1/8
1/8
1/8
3/16
1/16
1/8
1/16
1/8
1/4
1/8
.75
.75
.93
.93
.98
1.00
3-4 CBZ
4-1 CBZ
4-2 CBZ
4-4 CBZ
4-6 CBZ
4-8 CBZ
5-2 CBZ
3MSEL4N
4MSEL1N
4MSEL2N
4MSEL4N
4MSEL6N
4MSEL8N
5MSEL2N
300-2-4
400-2-1
400-2-2
400-2-4
400-2-6
400-2-8
500-2-2
3/16
1/4
1/4
1/4
1/4
1/4
5/16
1/4
1/16
1/8
1/4
3/8
1/2
1/8
5-4 CBZ
6-2 CBZ
6-4 CBZ
6-6 CBZ
6-8 CBZ
5MSEL4N
6MSEL2N
6MSEL4N
6MSEL6N
6MSEL8N
500-2-4
600-2-2
600-2-4
600-2-6
600-2-8
5/16
3/8
3/8
3/8
3/8
6-12 CBZ
8-4 CBZ
8-6 CBZ
8-8 CBZ
8-12 CBZ
6MSEL12N
8MSEL4N
8MSEL6N
8MSEL8N
8MSEL12N
600-2-12
810-2-4
810-2-6
810-2-8
810-2-12
10-6 CBZ
10-8 CBZ
10-12 CBZ
12-8 CBZ
12-12 CBZ
10MSEL6N
10MSEL8N
10MSEL12N
12MSEL8N
12MSEL12N
14-12 CBZ
16-12 CBZ
16-16 CBZ
20-20 CBZ
24-24 CBZ
14MSEL12N
16MSEL12N
16MSEL16N
20MSEL20N
24MSEL24N
W
HEX
.71
.71
.71
.70
1.00
.74
.60
.60
.67
.67
.72
.74
.38
.38
.38
.38
.56
.38
7/16
7/16
7/16
7/16
9/16
1/2
1.01
1.06
1.08
1.07
1.17
1.26
1.17
.94
.74
.76
1.00
1.13
1.31
.82
.75
.77
.79
.78
.88
.97
.88
.56
.38
.38
.56
.56
.75
.38
9/16
1/2
1/2
9/16
3/4
7/8
5/8
1/4
1/8
1/4
3/8
1/2
1.17
1.20
1.20
1.26
1.32
1.01
.82
1.01
1.13
1.31
.88
.91
.91
.97
1.03
.56
.38
.56
.56
.75
5/8
5/8
5/8
3/4
7/8
3/8
1/2
1/2
1/2
1/2
3/4
1/4
3/8
1/2
3/4
1.45
1.42
1.42
1.43
1.53
1.50
1.12
1.12
1.31
1.50
1.16
1.02
1.02
1.03
1.13
.75
.56
.56
.75
.75
1-1/16
13/16
13/16
7/8
1-1/16
1010-2-6
1010-2-8
1010-2-12
1210-2-8
1210-2-12
5/8
5/8
5/8
3/4
3/4
3/8
1/2
3/4
1/2
3/4
1.43
1.43
1.56
1.56
1.56
1.25
1.31
1.50
1.50
1.50
1.03
1.03
1.16
1.16
1.16
.56
.75
.75
.75
.75
7/8
7/8
1-1/16
1-1/16
1-1/16
1410-2-12
1610-2-12
1610-2-16
2010-2-20
2410-2-24
7/8
1
1
1-1/4
1-1/2
3/4
3/4
1
1-1/4
1-1/2
1.76
1.94
1.94
2.61
3.06
1.66
1.65
1.84
1.88
2.38
1.36
1.45
1.45
1.75
2.00
.75
.75
.94
.97
1.00
1-3/8
1-3/8
1-3/8
1-5/8
1-7/8
NOTE: C dimension is typical finger-tight.
Sizes 20, 24 require additional lubrication prior to assembly.
14
Tube to Male Pipe

CBZ, MSELN
NPT Male
Metric Elbow
For metric tube
C
L
W HEX
H
R
MILLIMETERS
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
NPT
THREAD
W
HEX
CBZ 3-1/8
CBZ 3-1/4
CBZ 4-1/8
CBZ 4-1/4
CBZ 6-1/8
M3MSEL1/8N
M3MSEL1/4N
M4MSEL1/8N
M4MSEL1/4N
M6MSEL1/8N
3MO-2-2
3MO-2-4
4M0-2-2
4MO-2-4
6MO-2-2
3
3
4
4
6
1/8
1/4
1/8
1/4
1/8
23,6
24,6
25,4
26,2
27,0
17,8
23,4
18,8
25,4
18,8
17,0
18,0
19,2
19,6
19,6
9,7
14,2
9,7
14,2
9,7
7/16
1/2
1/2
1/2
1/2
CBZ 6-1/4
CBZ 6-3/8
CBZ 6-1/2
CBZ 8-1/8
CBZ 8-1/4
M6MSEL1/4N
M6MSEL3/8N
M6MSEL1/2N
M8MSEL1/8N
M8MSEL1/4N
6MO-2-4
6MO-2-6
6MO-2-8
8MO-2-2
8MO-2-4
6
6
6
8
8
1/4
3/8
1/2
1/8
1/4
27,0
29,8
31,8
28,8
28,8
23,4
26,2
33,0
19,8
24,4
19,6
22,4
24,4
21,3
21,3
14,2
14,2
19,0
9,7
14,2
1/2
11/16
13/16
9/16
9/16
CBZ 8-3/8
CBZ 8-1/2
CBZ 10-1/8
CBZ 10-1/4
CBZ 10-3/8
M8MSEL3/8N
M8MSEL1/2N
M10MSEL1/8N
M10MSEL1/4N
M10MSEL3/8N
8MO-2-6
8MO-2-8
10MO-2-8
10MO-2-4
10MO-2-6
8
8
10
10
10
3/8
1/2
1/8
1/4
3/8
30,6
32,7
31,5
31,5
31,5
26,2
33,0
21,6
26,2
26,2
23,1
25,2
23,9
23,9
23,9
14,2
19,1
9,7
14,2
14,2
11/16
13/16
11/16
11/16
11/16
CBZ 10-1/2
CBZ 12-1/4
CBZ 12-3/8
CBZ 12-1/2
CBZ 12-3/4
M10MSEL1/2N 10MO-2-8
M12MSEL3/4N 12MO-2-12
10
12
12
12
12
1/2
1/4
3/8
1/2
3/4
33,5
36,0
36,0
36,0
39,8
33,0
28,2
28,2
33,0
36,8
25,9
25,9
25,9
25,9
29,7
19,0
14,2
14,2
19,0
19,0
13/16
13/16
13/16
13/16
1-1/16
CBZ 15-1/2
CBZ 16-3/8
CBZ 16-1/2
CBZ 16-3/4
CBZ 18-1/2
M16MSEL3/4N 16MO-2-12
15
16
16
16
18
1/2
3/8
1/2
3/4
1/2
38,0
38,0
38,0
39,8
39,8
35,1
30,2
35,1
36,8
36,8
27,9
27,9
27,9
29,7
29,7
19,0
14,2
19,0
19,0
19,0
15/16
15/16
15/16
1-1/16
1-1/16
CBZ 18-3/4
CBZ 20-1/2
CBZ 20-3/4
CBZ 22-3/4
CBZ 25-3/4
CBZ 25-1
M18MSEL3/4N
M20MSEL1/2N
M20MSEL3/4N
M22MSEL3/4N
M25MSEL3/4N
M25MSEL1N
18
20
20
22
25
25
3/4
1/2
3/4
3/4
3/4
1
39,8
44,6
44,6
44,6
49,1
49,1
36,8
41,7
41,7
41,7
41,7
46,5
29,7
34,5
34,5
34,5
36,8
36,8
19,0
19,0
19,0
19,0
19,0
23,9
1-1/16
1-3/8
1-3/8
1-3/8
1-3/8
1-3/8
18MO-2-12
20MO-2-8
20MO-2-12
22MO-2-12
25MO-2-12
25MO-2-16
CBZ, MSELK
BSP Taper
Male Elbow
For fractional tube
BSP
INCH
CPI
PART NO.
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
4-2K CBZ
4-4K CBZ
4-6K CBZ
4-8K CBZ
5-4K CBZ
4MSEL2K
4MSEL4K
4MSEL6K
4MSEL8K
5MSEL4K
400-2-2RT
400-2-4RT
400-2-6RT
400-2-8RT
500-2-4RT
1/4
1/4
1/4
1/4
5/16
1/8
1/4
3/8
1/2
1/4
1.02
1.08
1.17
1.26
1.17
6-4K CBZ
6-6K CBZ
8-6K CBZ
8-8K CBZ
6MSEL4K
6MSEL6K
8MSEL6K
8MSEL8K
600-2-4RT
600-2-4RT
810-2-6RT
810-2-8RT
3/8
3/8
1/2
1/2
1/4
3/8
3/8
1/2
1.13
1.26
1.35
1.41
TUBE
O.D.
BSPT
THREAD
W
HEX
.78
.94
1.13
1.31
.82
.72
.78
.88
.97
.88
.38
.56
.56
.75
.38
7/16
9/16
3/4
7/8
5/8
1.00
1.25
1.25
1.31
.84
.97
.97
1.03
.56
.56
.56
.75
9/16
3/4
3/4
7/8
C
L
BSP
W HEX
H
R
15
Tube to Male Pipe

CBZ, MSELK
BSP Taper Male
Elbow
For metric tube
BSP
C
L
BSP
H
R
W HEX
MILLIMETERS
INCH
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
BSPT
THREAD
W
HEX
CBZ 3-1/8
CBZ 3-1/4
CBZ 4-1/8
CBZ 4-1/4
CBZ 6-1/8
M3MSEL1/8K
M3MSEL1/4K
M4MSEL1/8K
M4MSEL1/4K
M6MSEL1/8K
3MO-2-2RT
3MO-2-4RT
4MO-2-2RT
4MO-2-4RT
6MO-2-2RT
3
3
4
4
6
1/8
1/4
1/8
1/4
1/8
23,6
24,6
25,4
24,6
27,0
17,8
23,4
18,8
23,4
18,8
17,0
18,0
18,8
18,8
19,6
9,7
14,2
9,7
14,2
9,7
7/16
1/2
1/2
1/2
1/2
CBZ 6-1/4
CBZ 6-3/8
CBZ 6-1/2
CBZ 8-1/8
CBZ 8-1/4
M6MSEL1/4K
M6MSEL3/8K
M6MSEL1/2K
M8MSEL1/8K
M8MSEL1/4K
6MO-2-4RT
6MO-2-6RT
6MO-2-8RT
8MO-2-2RT
8MO-2-4RT
6
6
6
8
8
1/4
3/8
1/2
1/8
1/4
27,0
29,8
31,8
28,8
28,8
23,4
26,2
33,0
19,8
24,4
19,6
22,4
24,4
21,3
21,3
14,2
14,2
19,0
9.7
14,2
1/2
11/16
13/16
9/16
9/16
CBZ 8-3/8
CBZ 8-1/2
CBZ 10-1/8
CBZ 10-1/4
CBZ 10-3/8
M8MSEL3/8K
M8MSEL1/2K
M10MSEL1/8K
M10MSEL1/4K
M10MSEL3/8K
8MO-2-6RT
8MO-2-8RT
10MO-2-2RT
10MO-2-4RT
10MO-2-6RT
8
8
10
10
10
3/8
1/2
1/8
1/4
3/8
30,6
32,7
31,5
31,5
31,5
26,2
33,0
21,6
26,2
26,2
23,1
25,2
23,9
23,9
23,9
14,2
19,1
9,7
14,2
14,2
11/16
13/16
11/16
11/16
11/16
CBZ 10-1/2
CBZ 12-1/4
CBZ 12-3/8
CBZ 12-1/2
CBZ 12-3/4
M10MSEL1/2K 10MO-2-8RT
10
12
12
12
12
1/2
1/4
3/8
1/2
3/4
33,5
36,0
36,0
36,0
39,8
33,0
28,2
28,2
33,0
36,8
25,9
25,9
25,9
25,9
29,7
19,0
14,2
14,2
19,0
19,1
13/16
13/16
13/16
13/16
1-1/16
CBZ 16-3/8
CBZ 16-1/2
CBZ 18-1/2
CBZ 18-3/4
CBZ 20-3/4
CBZ 25-3/4
CBZ 25-1
M16MSEL3/8K
M16MSEL1/2K
M18MSEL1/2K
M18MSEL3/4K
M20MSEL3/4K
M25MSEL3/4K
M25MSEL1K
16
16
18
18
20
25
25
3/8
1/2
1/2
3/4
3/4
3/4
1
38,0
38,0
39,8
39,8
44,6
49,0
49,1
30,2
35,1
36,8
36,8
41,7
41,7
46,5
27,9
27,9
29,7
29,7
34,5
36,8
36,8
14,2
19,0
19,0
19,0
19,0
19,1
23,9
15/16
15/16
1-1/16
1-1/16
1-3/8
1-3/8
1-3/8
16MO-2-6RT
16MO-2-8RT
18MO-2-8RT
18MO-2-12RT
20MO-2-12RT
25MO-2-12RT
25MO-2-16RT
16
Tube to Male Pipe

VBZ, MVELN
NPT Male
45 Elbow
For fractional tube
L
C
W HEX
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
NPT PIPE
THREAD
W
HEX
1-1 VBZ
2-2 VBZ
3-2 VBZ
4-2 VBZ
4-4 VBZ
1MVEL1N
2MVEL2N
3MVEL2N
4MVEL2N
4MVEL4N
100-5-1
200-5-2
300-5-2
400-5-2
400-5-4
1/16
1/8
3/16
1/4
1/4
1/16
1/8
1/8
1/8
1/4
.43
.60
.64
.70
.70
.468
.59
.56
.63
.66
.569
.66
.58
.66
.86
.38
.38
.38
.38
.56
3/8
7/16
7/16
9/16
9/16
5-2 VBZ
6-2 VBZ
6-4 VBZ
6-6 VBZ
8-6 VBZ
5MVEL2N
6MVEL2N
6MVEL4N
6MVEL6N
8MVEL6N
500-5-2
600-5-2
600-5-4
600-5-6
810-5-6
5/16
3/8
3/8
3/8
1/2
1/8
1/8
1/4
3/8
3/8
.73
.76
.76
.76
.87
.66
.72
.72
.75
.75
.66
.67
.86
.95
.95
.38
.38
.56
.56
.56
9/16
9/16
9/16
3/4
3/4
10-8 VBZ
12-12 VBZ
14-12 VBZ
16-16 VBZ
10MVEL8N
12MVEL12N
14MVEL12N
16MVEL16N
1010-5-8
1210-5-8
1410-5-8
1610-5-8
5/8
3/4
7/8
1
1/2
3/4
3/4
1
.87
.87
.87
1.05
.81
.84
1.36
1.19
1.17
1.20
1.27
1.48
.75
.75
.75
.94
7/8
1-1/16
1-5/16
1-5/16
VBZ, MVELN
NPT Male
45 Elbow
For metric tube
MILLIMETERS
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
NPT PIPE
THREAD
W
HEX
VBZ 6-1/8
VBZ 6-1/4
VBZ 8-1/8
VBZ 10-1/4
VBZ 12-3/8
M6MVEL1/8N
M6MVEL1/4N
M8MVEL1/8N
M10MVEL1/4N
M12MVEL3/8N
6
6
8
10
12
1/8
1/4
1/8
1/4
3/8
17,7
17,7
18,6
19,5
22,0
16,0
16,0
16,8
19,0
19,0
16,8
21,8
16,8
24,1
24,1
9,5
14,3
9,5
14,3
14,3
14,0
14,0
14,0
19,0
19,0
VBZ 12-1/2
VBZ 16-1/2
M12MVEL1/2N
M16MVEL1/2N
12
16
1/2
1/2
22,0
22,0
20,6
20,6
29,7
29,7
19,0
19,0
22,0
22,0
L
C
W HEX
17
Tube to Male Pipe

RBZ, MRTN
NPT Male
Run Tee
For fractional tube
A
C
L
H
R
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
2-2-2 RBZ
2-4-2 RBZ
3-2-3 RBZ
4-2-4 RBZ
4-4-4 RBZ
2MRT2N
2MBT4N
3MRT2N
4MRT2N
4MRT4N
200-3-2TMT
200-3-4TMT
300-3-2TMT
400-3-2TMT
400-3-4TMT
1/8
1/8
3/16
1/4
1/4
1/8
1/4
1/8
1/8
1/4
1.67
1.98
1.74
1.80
2.07
.92
.98
1.00
1.06
1.07
5-2-5 RBZ
5-4-5 RBZ
6-4-6 RBZ
6-6-6 RBZ
8-6-8 RBZ
5MRT2N
5MRT4N
6MRT4N
6MRT6N
8MRT6N
500-3-2TMT
500-3-4TMT
600-3-4TMT
600-3-6TMT
810-3-6TMT
5/16
5/16
3/8
3/8
1/2
1/8
1/4
1/4
3/8
3/8
2.00
2.18
2.21
2.43
2.82
8-8-8 RBZ
10-8-10 RBZ
12-12-12 RBZ
14-12-14 RBZ
16-12-16 RBZ
16-16-16 RBZ
8MRT8N
10MRT8N
12MRT12N
14MRT12N
16MRT12N
16MRT16N
810-3-8TMT
1010-3-8TMT
1210-3-12TMT
1410-3-12TMT
1610-3-12TMT
1610-3-16TMT
1/2
5/8
3/4
7/8
1
1
1/2
1/2
3/4
3/4
3/4
1
2.74
2.81
3.06
3.26
3.60
3.78
TUBE
O.D.
NPT PIPE
THREAD
W
HEX
.71
1.00
.74
.74
1.00
.66
.72
.74
.77
.78
.38
.56
.38
.38
.56
5/16
1/2
1/2
1/2
9/16
1.17
1.17
1.20
1.31
1.42
.82
1.01
1.01
1.12
1.12
.88
.88
.91
1.02
1.02
.38
.56
.56
.56
.56
5/8
5/8
5/8
13/16
13/16
1.43
1.43
1.56
1.76
1.94
1.94
1.31
1.38
1.50
1.50
1.66
1.84
1.03
1.03
1.16
1.36
1.45
1.45
.75
.75
.75
.75
.75
.94
7/8
7/8
1-1/16
1-5/16
1-5/16
1-3/8
W HEX
RBZ, MRTN
NPT Male
Run Tee
CPI
PART NO.
For metric tube
A-LOK
PART NO.
INTERCHANGES
WITH
MILLIMETERS
INCH
TUBE
O.D.
NPT
THREAD
W
HEX
RBZ 6-1/8-6
RBZ 6-1/4-6
RBZ 8-1/8-8
RBZ 8-1/4-8
RBZ 10-1/4-10
M6MRT1/8N
6MO-3-2TMT
M6MRT1/4N
6MO-3-4TMT
M8MRT1/8N
8MO-3-2TMT
M8MRT1/4N
8MO-3-4TMT
M10MRT1/4N 10MO-3-4TMT
6
6
8
8
10
1/8
1/4
1/8
1/4
1/4
45,8
50,3
50,7
55,3
61,7
27,0
27,0
29,9
29,9
33,5
18,0
23,4
20,8
25,4
28,2
19,6
19,6
22,4
22,4
25,9
9,7
14,2
9,7
14,2
14,2
1/2
1/2
5/8
5/8
13/16
RBZ 10-1/2-10
RBZ 12-1/4-12
RBZ 12-3/8-12
RBZ 12-1/2-12
RBZ 16-1-16
M10MRT1/2N
M12MRT1/4N
M12MRT3/8N
M12MRT1/2N
M16MRT1N
10
12
12
12
16
1/2
1/4
3/8
1/2
1
66,5
64,2
64,2
69,0
93,1
33,5
36,0
36,0
36,0
46,6
33,0
28,2
28,2
33,0
46,5
25,9
25,9
25,9
25,9
34,4
19,0
14,2
14,2
19,0
23,9
13/16
13/16
13/16
13/16
1-3/8
10MO-3-8TMT
12MO-3-4TMT
12MO-3-6TMT
12MO-3-8TMT
16MO-3-16TMT
A
C
L
H
R
W HEX
18
Tube to Male Pipe

A
SBZ, MBTN
NPT Male
Branch Tee
C
L
For fractional tube

W HEX
H
R
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
2-2-2 SBZ
2-2-4 SBZ
3-3-2 SBZ
4-4-2 SBZ
4-4-4 SBZ
2MBT2N
2MBT4N
3MBT2N
4MBT2N
4MBT4N
200-3-2TTM
200-3-4TTM
300-3-2TTM
400-3-2TTM
400-3-4TTM
1/8
1/8
3/16
1/4
1/4
1/8
1/4
1/8
1/8
1/4
1.84
1.96
2.00
2.12
2.14
.92
.98
1.00
1.06
1.07
.71
1.00
.74
.74
1.00
.66
.72
.74
.77
.78
.38
.56
.38
.38
.56
7/16
9/16
1/2
1/2
9/16
5-5-2 SBZ
5-5-4 SBZ
6-6-4 SBZ
6-6-6 SBZ
8-8-6 SBZ
5MBT2N
5MBT4N
6MBT4N
6MBT6N
8MBT6N
500-3-2TTM
500-3-4TTM
600-3-4TTM
600-3-6TTM
810-3-6TTM
5/16
5/16
3/8
3/8
1/2
1/8
1/4
1/4
3/8
3/8
2.34
2.34
2.40
2.62
2.84
1.17
1.17
1.20
1.31
1.42
.82
1.01
1.01
1.12
1.12
.88
.88
.91
1.02
1.02
.38
.56
.56
.56
.56
5/8
5/8
5/8
13/16
13/16
8-8-8 SBZ
10-10-8 SBZ
12-12-12 SBZ
14-14-12 SBZ
16-16-12 SBZ
16-16-16 SBZ
8MBT8N
10MBT8N
12MBT12N
14MBT12N
16MBT12N
16MBT16N
810-3-8TTM
1010-3-8TTM
1210-3-12TTM
1410-3-12TTM
1610-3-12TTM
1610-3-16TTM
1/2
5/8
3/4
7/8
1
1
1/2
1/2
3/4
3/4
3/4
1
2.86
2.86
3.12
3.52
3.88
3.88
1.43
1.43
1.56
1.76
1.94
1.94
1.31
1.31
1.50
1.50
1.66
1.84
1.03
1.03
1.16
1.36
1.45
1.45
.75
.75
.75
.75
.75
.94
7/8
7/8
1-1/16
1-3/8
1-3/8
1-3/8
TUBE
O.D.
NPT PIPE
THREAD
W
HEX
A
C
L
SBZ, MBTN
NPT Male
Branch Tee
For metric tube
W HEX
H
R
MILLIMETERS
INCH
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
NPT
THREAD
W
HEX
SBZ 6-6-1/8
SBZ 6-6-1/4
SBZ 8-8-1/8
SBZ 8-8-1/4
SBZ 10-10-1/4
M6MBT1/8N
M6MBT1/4N
M8MBT1/8N
M8MBT1/4N
M10MBT1/4N
6MO-3TTM
6MO-3-4TTM
8MO-3TTM
8MO-3-4TTM
10MO-3-4TTM
6
6
8
8
10
1/8
1/4
1/8
1/4
1/4
53,9
53,9
59,7
59,7
67,0
27,0
27,0
29,9
29,9
33,5
18,8
23,4
20,8
25,4
28,2
19,6
19,6
22,4
22,4
25,9
9,7
14,2
9,7
14,2
14,2
1/2
1/2
5/8
5/8
13/16
SBZ 10-10-3/8
SBZ 12-12-1/4
SBZ 12-12-3/8
SBZ 12-12-1/2
SBZ 16-16-1/2
M10MBT3/8N
M12MBT1/4N
M12MBT3/8N
M12MBT1/2N
M16MBT1/2N
10MO-3-6TTM
12MO-3-4TTM
12MO-3-6TTM
12MO-3-8TTM
16MO-3-8TTM
10
12
12
12
16
3/8
1/4
3/8
1/2
1/2
67,0
72,0
72,0
72,0
77,6
33,5
36,0
36,0
36,0
38,8
28,2
28,2
28,2
33,0
35,8
25,9
25,9
25,9
25,9
28,7
14,2
14,2
14,2
19,0
19,1
13/16
13/16
13/16
13/16
1
19
Tube to Female Pipe

GBZ, FSCN
NPT Female
Connector
For fractional tube
A
W HEX
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
NPT PIPE
THREAD
W
HEX
1-1 GBZ
1-2 GBZ
2-2 GBZ
2-4 GBZ
3-2 GBZ
1FSC1N
1FSC2N
2FSC2N
2FSC4N
3FSC2N
100-7-1
100-7-2
200-7-2
200-7-4
300-7-2
1/16
1/16
1/8
1/8
3/16
1/16
1/8
1/8
1/4
1/8
.93
.95
1.14
1.32
1.17
.43
.43
.60
.60
.64
.78
.81
.88
1.06
.91
7/16
9/16
9/16
3/4
9/16
3-4 GBZ
4-2 GBZ
4-4 GBZ
4-6 GBZ
4-8 GBZ
3FSC4N
4FSC2N
4FSC4N
4FSC6N
4FSC8N
300-7-4
400-7-2
400-7-4
400-7-6
400-7-8
3/16
1/4
1/4
1/4
1/4
1/4
1/8
1/4
3/8
1/2
1.35
1.23
1.42
1.48
1.67
.64
.70
.70
.70
.70
1.09
.94
1.13
1.19
1.38
3/4
9/16
3/4
7/8
1-1/16
5-2 GBZ
5-4 GBZ
5-6 GBZ
6-2 GBZ
6-4 GBZ
5FSC2N
5FSC4N
5FSC6N
6FSC2N
6FSC4N
500-7-2
500-7-4
500-7-6
600-7-2
600-7-4
5/16
5/16
5/16
3/8
3/8
1/8
1/4
3/8
1/8
1/4
1.27
1.46
1.29
1.48
.73
.73
.73
.76
.76
.97
1.16
1.219
1.00
1.19
9/16
3/4
7/8
5/8
3/4
6-6 GBZ
6-8 GBZ
6-12 GBZ
8-4 GBZ
8-6 GBZ
6FSC6N
6FSC8N
6FSC12N
8FSC4N
8FSC6N
600-7-6
600-7-8
600-7-12
810-7-4
810-7-6
3/8
3/8
3/8
1/2
1/2
3/8
1/2
3/4
1/4
3/8
1.54
1.73
1.85
1.59
1.65
.76
.76
.76
.87
.87
1.25
1.44
1.56
1.19
1.25
7/8
1-1/16
1-1/4
13/16
7/8
8-8 GBZ
8-12 GBZ
10-6 GBZ
10-8 GBZ
10-12 GBZ
8FSC8N
8FSC12N
10FSC6N
10FSC8N
10FSC12N
810-7-8
810-7-12
1010-7-6
1010-7-8
1010-7-12
1/2
1/2
5/8
5/8
5/8
1/2
3/4
3/8
1/2
3/4
1.84
1.96
1.65
1.84
1.96
.87
.87
.87
.87
.87
1.44
1.56
1.25
1.44
1.56
1-1/16
1-1/4
15/16
1-1/16
1-3/8
12-8 GBZ
12-12 GBZ
14-12 GBZ
16-12 GBZ
16-16 GBZ
12FSC8N
12FSC12N
14FSC12N
16FSC12N
16FSC16N
1210-7-8
1210-7-12
1410-7-12
1610-7-12
1610-7-16
3/4
3/4
7/8
1
1
1/2
3/4
3/4
3/4
1
1.84
1.96
1.96
2.15
2.46
.87
.87
.87
1.05
1.05
1.44
1.56
1.56
1.66
1.97
1-1/16
1-3/8
1-3/8
1-3/8
1-5/8
20-20 GBZ
24-24 GBZ
32-32 GBZ
20FSC20N
24FSC24N
32FSC32N
2010-7-20
2410-7-24
3210-7-32
1-1/4
1-1/2
2
1-1/4
1-1/2
2
2.94
3.28
4.00
1.52
1.77
2.47
2.08
2.22
2.53
2
2-3/8
2-7/8
Sizes 20, 24, 32 require additional lubrication prior to assembly.
GBZ, FSCN
NPT Female
Connector
For metric tube
A
W HEX
MILLIMETERS
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
NPT
THREAD
W
HEX
GBZ 3-1/8
GBZ 3-1/4
GBZ 4-1/8
GBZ 6-1/8
GBZ 6-1/4
M3FSC1/8N
M3FSC1/4N
M4FSC1/8N
M6FSC1/8N
M6FSC1/4N
3MO-7-2
3MO-7-4
4MO-7-2
6MO-7-2
6MO-7-4
3
3
4
6
6
1/8
1/4
1/8
1/8
1/4
28,8
33,6
29,6
31,3
36,1
15,3
15,3
16,1
17,7
17,7
22,2
27,0
23,0
23,8
28,6
14,0
19,0
14,0
14,0
19,0
GBZ 6-3/8
GBZ 6-1/2
GBZ 8-1/8
GBZ 8-1/4
GBZ 8-3/8
M6FSC3/8N
M6FSC1/2N
M8FSC1/8N
M8FSC1/4N
M8FSC3/8N
6MO-7-6
6MO-7-8
8MO-7-2
8MO-7-4
8MO-7-6
6
6
8
8
8
3/8
1/2
1/8
1/4
3/8
37,7
42,5
32,1
36,9
38,5
17,7
17,7
18,6
18,6
18,6
30,2
35,0
24,6
29,4
31,0
22,0
27,0
14,0
19,0
22,0
GBZ 10-1/4
GBZ 10-3/8
GBZ 10-1/2
GBZ 12-1/4
GBZ 12-3/8
M10FSC1/4N
M10FSC3/8N
M10FSC1/2N
M12FSC1/4N
M12FSC3/8N
10MO-7-4
10MO-7-6
10MO-7-8
12MO-7-4
12MO-7-6
10
10
10
12
12
1/4
3/8
1/2
1/4
3/8
37,8
39,4
44,1
41,9
41,9
19,5
19,5
19,5
22,0
22,0
30,2
31,8
36,5
31,8
31,8
19,0
22,0
27,0
22,0
22,0
GBZ 12-1/2
GBZ 16-3/8
GBZ 16-1/2
GBZ 20-1/2
GBZ 20-3/4
M12FSC1/2N
M16FSC3/8N
M16FSC1/2N
M20FSC1/2N
M20FSC3/4N
12MO-7-8
16MO-7-6
16MO-7-8
20MO-7-8
20MO-7-12
12
16
16
20
20
1/2
3/8
1/2
1/2
3/4
46,6
41,9
46,9
47,9
49,7
22,0
22,0
22,0
22,0
22,0
36,5
31,8
36,5
37,8
39,6
27,0
27,0
27,0
30,0
35,0
GBZ 22-3/4
GBC 25-3/4
GBC 25-1
M22FSC3/4N
M25FSC3/4N
M25FSC1N
22MO-7-12
25MO-7-12
25MO-7-16
22
25
25
3/4
3/4
1
49,7
53,6
62,3
22,0
26,5
26,5
39,6
41,3
50,0
35,0
35,0
41,0
20
Tube to Female Pipe

GBZ, FSCK
BSP Taper
Female
Connector
For fractional tube
INCHES
BSP
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
BSPT
THREAD
W
HEX
BORE
4-2K GBZ
4-4K GBZ
4-6K GBZ
4-8K GBZ
6-4K GBZ
4FSC2K
4FSC4K
4FSC6K
4FSC8K
6FSC4K
400-7-2RT
400-7-4RT
400-7-6RT
400-7-8RT
600-7-4RT
1/4
1/4
1/4
1/4
3/8
1/8
1/4
3/8
1/2
1/4
1.24
1.42
1.49
1.68
1.48
.70
.70
.70
.70
.76
.94
1.13
1.19
1.38
1.19
9/16
3/4
7/8
1-1/16
3/4
.19
.19
.19
.19
.28
6-6K GBZ
6-8K GBZ
8-4K GBZ
8-6K GBZ
8-8K GBZ
6FSC6K
6FSC8K
8FSC4K
8FSC6K
8FSC8K
600-7-6RT
600-7-8RT
810-7-4RT
810-7-6RT
810-7-8RT
3/8
3/8
1/2
1/2
1/2
3/8
1/2
1/4
3/8
1/2
1.54
1.73
1.59
1.65
1.84
.76
.76
.87
.87
.87
1.25
1.44
1.19
1.25
1.44
7/8
1-1/16
13/16
7/8
1-1/16
.28
.28
.406
.406
.406
W HEX
BSP
GBZ, FSCK
BSP Taper
Female
Connector
For metric tube
BSP
A
W HEX
BSP
MILLIMETERS
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
GBZ3-1/8K
GBZ6-1/8K
GBZ6-1/4K
GBZ6-3/8K
GBZ6-1/2K
M3FSC1/8K
M6FSC1/8K
M6FSC1/4K
M6FSC3/8K
M6FSC1/2K
3MO-7-2RT
6MO-7-2RT
6MO-7-4RT
6MO-7-6RT
6MO-7-8RT
3
6
6
6
6
1/8
1/8
1/4
3/8
1/2
29,2
31,3
35,8
37,6
42,5
15,3
17,7
17,7
17,7
17,7
22,6
23,8
28,3
30,1
35,0
14,0
14,0
19,0
22,0
27,0
GBZ8-1/8K
GBZ8-1/4K
GBZ8-3/8K
GBZ8-1/2K
GBZ10-1/8K
M8FSC1/8K
M8FSC1/4K
M8FSC3/8K
M8FSC1/2K
M10FSC1/8K
8MO-7-2RT
8MO-7-4RT
8MO-7-6RT
8MO-7-8RT
10MO-7-2RT
8
8
8
8
10
1/8
1/4
3/8
1/2
1/8
32,8
37,0
38,5
43,3
33,0
18,6
18,6
18,6
18,6
19,5
25,3
29,5
31,0
35,8
25,4
15,0
19,0
22,0
27,0
18,0
GBZ10-1/4K
GBZ10-3/8K
GBZ10-1/2K
GBZ12-1/4K
GBZ12-3/8K
M10FSC1/4K
M10FSC3/8K
M10FSC1/2K
M12FSC1/4K
M12FSC3/8K
10MO-7-4RT
10MO-7-6RT
10MO-7-8RT
12MO-7-4RT
12MO-7-6RT
10
10
10
12
12
1/4
3/8
1/2
1/4
3/8
37,8
39,4
44,2
40,3
41,9
19,5
19,5
19,5
22,0
22,0
30,2
31,8
36,6
30,2
31,8
19,0
22,0
27,0
22,0
22,0
GBZ12-1/2K
GBZ16-1/2K
GBZ20-1/2K
GBZ20-3/4K
GBZ22-1K
M12FSC1/2K
M16FSC1/2K
M20FSC1/2K
M20FSC3/4K
M22FSC1K
12MO-7-8RT
16MO-7-8RT
20MO-7-8RT
20MO-7-12RT
22MO-7-16RT
12
16
20
20
22
1/2
1/2
1/2
3/4
1
46,7
48,4
54,7
49,7
57,9
22,0
22,0
22,0
22,0
22,0
36,6
38,3
44,6
39,6
47,8
27,0
18,0
30,0
35,0
41,0
GBZ25-3/4K
GBZ25-1K
M25FSC3/4K
M25FSC1K
25MO-7-12RT
25MO-7-16RT
25
25
3/4
1
54,3
61,5
26,5
26,5
42,1
49,3
35,0
41,0
TUBE
O.D.
BSPT
THREAD
W
HEX
21
Tube to Female Pipe

GH2BZ, FBCN
NPT Female
Bulkhead
Connector
For fractional tube
A
W HEX
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
NPT PIPE
THREAD
W
HEX
2-2 GH2BZ
3-2 GH2BZ
4-2 GH2BZ
4-4 GH2BZ
5-2 GH2BZ
2FBC2N
3FBC2N
4FBC2N
4FBC4N
5FBC2N
200-71-2
300-71-2
400-71-2
400-71-4
500-71-2
1/8
3/16
1/4
1/4
5/16
1/8
1/8
1/8
1/4
1/8
1.76
1.79
1.85
2.04
1.96
1.23
1.26
1.31
1.31
1.42
1.50
1.53
1.56
1.75
1.66
.97
1.00
1.02
1.02
1.12
9/16
9/16
5/8
3/4
11/16
5-8 GH2BZ
6-4 GH2BZ
8-6 GH2BZ
8-8 GH2BZ
10-8 GH2BZ
5FBC8N
6FBC4N
8FBC6N
8FBC8N
10FBC8N
500-71-8
600-71-4
810-71-6
810-71-8
1010-71-8
5/16
3/8
1/2
1/2
5/8
1/2
1/4
3/8
1/2
1/2
2.38
2.17
2.43
2.62
2.65
1.42
1.44
1.65
1.65
1.68
2.08
1.88
2.03
2.22
2.25
1.12
1.15
1.25
1.25
1.28
1-1/16
3/4
15/16
1-1/16
1-1/16
12-12 GH2BZ
14-12 GH2BZ
16-16 GH2BZ
12FBC12N
14FBC12N
16FBC16N
1210-71-12
1410-71-12
1610-71-16
3/4
7/8
1
3/4
3/4
1
2.90
3.18
3.68
1.87
2.09
2.27
2.50
2.78
3.19
1.47
1.69
1.78
1-3/8
1-3/8
1-5/8

L
D
GH2BZ, FBCN
NPT Female
Bulkhead
Connector
For metric tube
MILLIMETERS
CPI
PART NO.
GH2BZ 6-1/8
GH2BZ 6-1/4
GH2BZ 8-1/8
GH2BZ 10-1/4
GH2BZ 12-3/8
GH2BZ 12-1/2
A-LOK
PART NO.
INTERCHANGES
WITH
M6FBC1/8N 6MO-71-2
M6FBC1/4N 6MO-71-4
M8FBC1/8N 8MO-71-2
M10FBC1/4N 10MO-71-4
M12FBC3/8N 12MO-71-6
M12FBC1/2N 12MO-71-8
TUBE
NPT
O.D. THREAD
6
6
8
10
12
12
1/8
1/4
1/8
1/4
3/8
1/2
W
HEX
47,2
52,0
49,6
55,2
60,9
66,4
33,7
33,7
36,1
37,0
41,9
41,9
39,7
44,5
42,1
47,6
50,8
56,3
26,2
26,2
28,5
29,4
31,8
31,8
16,0
19,0
18,0
19,0
24,0
27,0
BHEAD
HOLE
MAX.
DRILL BHEAD
SIZE
THICK.
11,5
11,5
13,1
16,3
19,5
19,5
10,2
10,2
11,2
11,2
12,7
12,7

A
W HEX
L
D
GBZ, FSC GC
BSPP Gauge
Connector
For fractional tube
BSPP
A
W HEX
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
4-4GC GBZ
4-6GC GBZ
4-8GC GBZ
5-4GC GBZ
5-8GC GBZ
4FSC4GC
4FSC6GC
4FSC8GC
5FSC4GC
5FSC8GC
400-7-4RG
400-7-6RG
400-7-8RG
500-7-4RG
500-7-8RG
1/4
1/4
1/4
5/16
5/16
1/4
3/8
1/2
1/4
1/2
1.48
1.48
1.70
1.51
1.59
.70
.70
.70
.73
.73
1.19
1.19
1.41
1.22
1.30
3/4
7/8
1-1/16
3/4
1-1/16
.19
.19
.19
.21
.28
6-4GC GBZ
6-6GC GBZ
6-8GC GBZ
8-4GC GBZ
8-6GC GBZ
8-8GC GBZ
6FSC4GC
6FSC6GC
6FSC8GC
8FSC4GC
8FSC6GC
8FSC8GC
600-7-4RG
600-7-6RG
600-7-8RG
810-7-4RG
810-7-6RG
810-7-8RG
3/8
3/8
3/8
1/2
1/2
1/2
1/4
3/8
1/2
1/4
3/8
1/2
1.55
1.55
1.63
1.65
1.75
1.90
.76
.76
.76
.86
.86
.86
1.25
1.25
1.33
1.25
1.35
1.50
3/4
7/8
1-1/16
13/16
7/8
1-1/16
.21
.26
.28
.21
.26
.28
TUBE
O.D.
BSPP
THREAD
W
HEX
BORE
BSPP

See Catalog 4260 Pipe/ISO Fittings for detailed information.
Sealing Washer on page 72 to be used with this fitting.
22
Tube to Female Pipe

GBZ, GCR
BSPP Gauge
Connector
For metric tube
BSPP
A
W HEX
MILLIMETERS
BSPP
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
BSPP
THREAD
W
HEX
GBZ 3-1/4GC
GBZ 6-1/4GC
GBZ 6-3/8GC
GBZ 6-1/2GC
GBZ 8-1/4GC
M3GC1/4R
M6GC1/4R
M6GC3/8R
M6GC1/2R
M8GC1/4R
3MO-7-4RG
6MO-7-4RG
6MO-7-6RG
6MO-7-8RG
8MO-7-4RG
3
6
6
6
8
1/4
1/4
3/8
1/2
1/4
35,3
37,7
37,7
43,2
38,5
15,3
17,7
17,7
17,7
18,6
28,7
30,2
30,2
35,7
31,0
19,0
19,0
22,0
27,0
19,0
GBZ 8-3/8GC
GBZ 8-1/2GC
GBZ 10-1/4GC
GBZ 10-3/8GC
GBC 10-1/2GC
M8GC3/8R
M8GC1/2R
M10GC1/4R
M10GC3/8R
M10GC1/2R
8MO-7-6RG
8MO-7-8RG
10MO-7-4RG
10MO-7-6RG
10MO-7-8RG
8
8
10
10
10
3/8
1/2
1/4
3/8
1/2
40,8
44,0
39,4
38,8
41,3
18,6
18,6
19,5
19,5
19,5
33,3
36,5
31,8
31,2
33,7
22,0
27,0
19,0
22,0
27,0
GBC 12-1/4GC
GBC 12-3/8GC
GBC 12-1/2GC
M12GC1/4R
M12GC3/8R
M12GC1/2R
12MO-7-4RG
12MO-7-6RG
12MO-7-8RG
12
12
12
1/4
3/8
1/2
41,9
44,4
48,2
22,0
22,0
22,0
31,8
34,3
38,1
22,0
22,0
27,0

See Catalog 4260 Pipe/ISO Fittings for detailed information.
Sealing Washer on page 72 to be used with this fitting.
DBZ, FELN
NPT Female
Elbow
For fractional tube
C
L
W HEX
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
NPT PIPE
THREAD
1-1 DBZ
1-2 DBZ
2-2 DBZ
2-4 DBZ
3-2 DBZ
1FEL1N
1FEL2N
2FEL2N
2FEL4N
3FEL2N
100-8-1
100-8-2
200-8-2
200-8-4
300-8-2
1/16
1/16
1/8
1/8
3/16
1/16
1/8
1/8
1/4
1/8
4-2 DBZ
4-4 DBZ
4-6 DBZ
4-8 DBZ
5-2 DBZ
4FEL2N
4FEL4N
4FEL6N
4FEL8N
5FEL2N
400-8-2
400-8-4
400-8-6
400-8-8
500-8-2
1/4
1/4
1/4
1/4
5/16
5-4 DBZ
6-2 DBZ
6-4 DBZ
6-6 DBZ
6-8 DBZ
5FEL4N
6FEL2N
6FEL4N
6FEL6N
6FEL8N
500-8-4
600-8-2
600-8-4
600-8-6
600-8-8
8-4 DBZ
8-6 DBZ
8-8 DBZ
10-6 DBZ
10-8 DBZ
8FEL4N
8FEL6N
8FEL8N
10FLE6N
10FEL8N
12-8 DBZ
12-12 DBZ
14-12 DBZ
16-12 DBZ
16-16 DBZ
12FEL8N
12FEL12N
14FEL12N
16FEL12N
16FEL16N
W
HEX
.71
.81
.98
1.10
1.01
.56
.75
.75
.88
.75
.56
.66
.72
.84
.75
7/16
9/16
9/16
3/4
9/16
1/8
1/4
3/8
1/2
1/8
1.07
1.20
1.26
1.35
1.17
.75
.88
.88
1.13
.75
.78
.91
.97
1.06
.88
9/16
3/4
7/8
1-1/16
5/8
5/16
3/8
3/8
3/8
3/8
1/4
1/8
1/4
3/8
1/2
1.24
1.20
1.26
1.32
1.42
.88
.75
.88
.88
1.13
.94
.91
.97
1.03
1.13
3/4
5/8
3/4
7/8
1-1/16
810-8-4
810-8-6
810-8-8
1010-8-6
1010-8-8
1/2
1/2
1/2
5/8
5/8
1/4
3/8
1/2
3/8
1/2
1.42
1.43
1.53
1.43
1.53
.88
.88
1.13
.88
1.13
1.02
1.03
1.13
1.03
1.13
13/16
7/8
1-1/16
7/8
1-1/16
1210-8-8
1210-8-12
1410-8-12
1610-8-12
1610-8-16
3/4
3/4
7/8
1
1
1/2
3/4
3/4
3/4
1
1.56
1.65
1.76
1.94
2.02
1.13
1.25
1.25
1.25
1.50
1.16
1.36
1.36
1.45
1.53
1-1/16
1-3/8
1-3/8
1-3/8
1-5/8
DBZ, FELN
NPT Female
Elbow
For metric tube
C
L
W HEX
MILLIMETERS
INCH
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
NPT
THREAD
W
HEX
DBZ 6-1/8
DBZ 6-1/4
DBZ 8-1/8
DBZ 8-1/4
DBZ 10-1/4
M6FEL1/8N
M6FEL1/4N
M8FEL1/8N
M8FEL1/4N
M10FEL1/4N
6MO-8-2
6MO-8-4
8MO-8-2
8MO-8-4
10MO-8-4
6
6
8
8
10
1/8
1/4
1/8
1/4
1/4
27,0
29,8
28,8
30,6
33,5
19,0
22,4
19,1
22,4
22,4
19,6
22,4
21,3
23,1
25,9
1/2
11/16
9/16
11/16
13/16
DBZ 10-3/8
DBZ 10-1/2
DBZ 12-1/4
DBZ 12-3/8
DBZ 12-1/2
M10FEL3/8N
M10FEL1/2N
M12FEL1/4N
M12FEL3/8N
M12FEL1/2N
10MO-8-6
10MO-8-8
12MO-8-4
12MO-8-6
12MO-8-8
10
10
12
12
12
3/8
1/2
1/4
3/8
1/2
33,5
36,3
36,0
36,0
38,8
22,4
28,5
22,4
22,4
28,4
25,9
28,7
25,9
25,9
28,7
13/16
1
13/16
13/16
1
DBZ 16-3/8
DBZ 16-1/2
M16FEL3/8N
M16FEL1/2N
16MO-8-6
16MO-8-8
16
16
3/8
1/2
39,5
39,5
23,6
28,4
29,7
29,7
1-1/16
1-1/16
23
Tube to Female Pipe

MBZ, FRTN
NPT Female
Run Tee
For fractional tube
A
C
L
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
NPT PIPE
THREAD
2-2-2 MBZ
3-2-3 MBZ
4-2-4 MBZ
4-4-4 MBZ
5-2-5 MBZ
2FRT2N
3FRT2N
4FRT2N
4FRT4N
5FRT2N
200-3-2TFT
300-3-2TFT
400-3-2TFT
400-3-4TFT
500-3-2TFT
1/8
3/16
1/4
1/4
5/16
1/8
1/8
1/8
1/4
1/8
1.76
1.76
1.82
2.08
1.92
6-4-6 MBZ
8-4-8 MBZ
8-6-8 MBZ
8-8-8 MBZ
10-8-10 MBZ
6FRT4N
8FRT4N
8FRT6N
8FRT8N
10FRT8N
600-3-4TFT
810-3-4TFT
810-3-6TFT
810-3-8TFT
1010-3-8TFT
3/8
1/2
1/2
1/2
5/8
1/4
1/2
3/8
1/2
1/2
12-12-12 MBZ
14-8-14 MBZ
14-12-14 MBZ
16-12-16 MBZ
16-16-16 MBZ
12FRT12N
14FRT8N
14FRT12N
16FRT12N
16FRT16N
1210-3-12TFT
1410-3-8TFT
1410-3-12TFT
1610-3-12TFT
1610-3-16TFT
3/4
7/8
7/8
1
1
3/4
1/2
3/4
3/4
1
W
HEX
1.01
1.01
1.07
1.20
1.17
.75
.75
.75
.88
.75
.75
.75
.78
.91
.88
9/16
9/16
9/16
3/4
5/8
2.14
2.56
2.34
2.66
2.66
1.26
1.43
1.43
1.53
1.53
.88
1.13
.91
1.13
1.13
.97
1.13
1.03
1.13
1.13
3/4
13/16
7/8
1-1/16
1-1/16
2.90
3.01
3.01
3.19
3.52
1.65
1.76
1.76
1.94
2.02
1.25
1.25
1.25
1.25
1.50
1.36
1.36
1.36
1.45
1.53
1-3/8
1-3/8
1-3/8
1-3/8
1-3/8
W HEX
MBZ, FRTN
NPT Female
Run Tee
CPI
PART NO.
For metric tube
A-LOK
PART NO.
INTERCHANGES
WITH
MILLIMETERS
INCH
TUBE
O.D.
NPT
THREAD
W
HEX
MBZ 6-1/8-6
MBZ 6-1/4-6
MBZ 6-1/8-6
MBZ 10-1/4-10
MBZ 12-1/4-12
M6FRT1/8N
6MO-3TFT
M6FRT1/4N
6MO-3-4TFT
M8FRT1/8N
8MO-3TFT
M10FRT1/4N 10MO-3TFT
M12FRT1/4N 12MO-3-4TFT
6
6
8
10
12
1/8
1/4
1/8
1/4
1/4
46,0
52,1
48,9
55,9
58,4
27,0
29,8
29,9
33,5
36,0
19,0
22,4
19,0
22,4
22,4
19,6
22,4
22,4
25,9
25,9
1/2
11/16
5/8
13/16
13/16
MBZ 12-3/8-12
MBZ 12-1/2-12
MBZ 16-1/2-16
M12FRT3/8N 12MO-3TFT
M12FRT1/2N 12MO-3-8TFT
M16FRT1/2N 16MO-3TTF
12
12
16
3/8
1/2
1/2
58,4
67,3
68,2
36,0
38,8
39,8
22,4
28,5
28,4
25,9
28,7
29,7
13/16
1
1-1/16
A
C
L
W HEX
24
Tube to Female Pipe

A
OBZ, FBTN
NPT Female
Branch Tee
C
L
For fractional tube

H
W HEX
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
NPT PIPE
THREAD
W
HEX
2-2-2 OBZ
3-3-2 OBZ
4-4-2 OBZ
4-4-4 OBZ
5-5-2 OBZ
2FBT2N
3FBT2N
4FBT2N
4FBT4N
5FBT2N
200-3-2TTF
300-3-2TTF
400-3-2TTF
400-3-4TTF
500-3-2TTF
1/8
3/16
1/4
1/4
5/16
1/8
1/8
1/8
1/4
1/8
2.02
2.02
2.14
2.40
2.34
1.01
1.01
1.07
1.20
1.17
.75
.75
.75
.88
.75
.75
.75
.78
.91
.88
9/16
9/16
9/16
3/4
5/8
6-6-4 OBZ
8-8-4 OBZ
8-8-6 OBZ
8-8-8 OBZ
10-10-8 OBZ
6FBT4N
8FBT4N
8FBT6N
8FBT8N
10FBT8N
600-3-4TTF
810-3-4TTF
810-3-6TTF
810-3-8TTF
1010-3-8TTF
3/8
1/2
1/2
1/2
5/8
1/4
1/4
3/8
1/2
1/2
2.52
2.86
2.86
3.06
3.06
1.26
1.43
1.43
1.53
1.53
.88
.88
.91
1.13
1.13
.97
1.02
1.03
1.13
1.13
3/4
13/16
7/8
1-1/16
1-1/16
12-12-12 OBZ
14-14-12 OBZ
16-16-12 OBZ
16-16-16 OBZ
12FBT12N
14FBT12N
16FBT12N
16FBT16N
1210-3-12TTF
1410-3-12TTF
1610-3-12TTF
1610-3-16TTF
3/4
7/8
1
1
3/4
3/4
3/4
1
3.30
3.52
3.88
4.04
1.65
1.76
1.94
2.02
1.25
1.25
1.25
1.50
1.36
1.36
1.45
1.53
1-3/8
1-3/8
1-3/8
1-3/8
OBZ, FBTN
NPT Female
Branch Tee
C
L
For metric tube

H
W HEX
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
MILLIMETERS
INCH
TUBE
O.D.
NPT
THREAD
W
HEX
OBZ 6-6-1/8
M6FBT1/8N
6MO-3TTF
OBZ 6-6-1/4
M6FBT1/4N 6MO-3-4TTF
OBZ 8-8-1/8
M8FBT1/8N
8MO-3TTF
OBZ 10-10-1/4 M10FBT1/4N 10MO-3TTF
OBZ 12-12-1/8 M12FBT1/8N 12MO-3TTF
6
6
8
10
12
1/8
1/4
1/8
1/4
1/8
53,9
59,5
59,7
67,0
72,0
27,0
29,8
29,9
33,5
36,0
19,0
22,4
19,0
22,4
22,3
19,6
22,4
22,4
25,9
25,9
1/2
11/16
5/8
13/16
13/16
OBZ 12-12-1/4
OBZ 12-12-3/8
OBZ 12-12-1/2
OBZ 16-16-1/2
12
12
12
16
1/4
3/8
1/2
1/2
72,0
72,0
77,6
77,6
36,0
36,0
38,8
38,8
22,3
22,4
28,5
28,4
25,9
25,9
28,7
28,7
13/16
13/16
1
1
M12FBT3/8N 12MO-3TTF
M16FBT1/2N 16MO-3TTF
25
Tube to Tube Unions

HBZ, SC
Union
For fractional tube
A
C
W HEX
D
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
1-1 HBZ
2-2 HBZ
3-3 HBZ
4-4 HBZ
1SC1
2SC2
3SC3
4SC4
100-6
200-6
300-6
400-6
1/16
1/8
3/16
1/4
.99
1.39
1.48
1.62
5-5 HBZ
5SC5
500-6
5/16
6-6 HBZ
6SC6
600-6
3/8
8-8 HBZ
10-10 HBZ
8SC8
10SC10
810-6
1010-6
12-12 HBZ
14-14 HBZ
12SC12
14SC14
16-16 HBZ
20-20 HBZ
24-24 HBZ
32-32 HBZ
16SC16
20SC20
24SC24
32SC32
W
HEX
.43
.60
.64
.70
.69
.88
.95
1.03
5/16
7/16
7/16
1/2
1.70
.73
1.11
9/16
1.77
.76
1.19
5/8
1/2
5/8
2.02
2.05
.87
.87
1.22
1.25
13/16
15/16
1210-6
1410-6
3/4
7/8
2.11
2.18
.87
.87
1.31
1.38
1-1/16
1-3/16
1610-6
2010-6
2410-6
3210-6
1
1-1/4
1-1/2
2
2.57
3.61
4.23
5.88
1.05
1.52
1.77
2.47
1.59
1.89
2.11
2.94
1-3/8
1-3/4
2-1/8
2-3/4
HBZ, SCM
Union
For metric tube
A
C
W HEX
D
MILLIMETERS
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
W
HEX
HBZ 2-2
HBZ 3-3
HBZ 4-4
HBZ 6-6
HBZ 8-8
SCM2
SCM3
SCM4
SCM6
SCM8
2MO-6
3MO-6
4MO-4
6MO-6
8MO-6
2
3
4
6
8
35,6
35,3
37,4
41,2
43,2
15,3
15,3
16,1
17,7
18,6
22,4
22,1
24,2
26,2
28,2
12,0
12,0
12,0
14,0
15,0
HBZ 10-10
HBZ 12-12
HBZ 14-14
HBZ 15-15
HBZ 16-16
SCM10
SCM12
SCM14
SCM15
SCM16
10MO-6
12MO-6
14MO-6
15MO-6
16MO-6
10
12
14
15
16
46,2
51,2
52,0
52,0
52,0
19,5
22,0
22,0
22,0
22,0
31,0
31,0
31,8
31,8
31,8
18,0
22,0
24,0
24,0
24,0
HBZ 18-18
HBZ 20-20
HBZ 22-22
HBZ 25-25
SCM18
SCM20
SCM22
SCM25
18MO-6
20MO-6
22MO-6
25MO-6
18
20
22
25
53,5
55,0
55,0
65,1
22,0
22,0
22,0
26,5
33,3
34,8
34,8
40,5
27,0
30,0
30,0
35,0
26
Tube to Tube Unions

HBZ, CU
Conversion
Union
For metric tube
Metric Tube to Inch Tube
A
C1
C2
T1
T2
W HEX
TUBE O.D.
MILLIMETERS
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
HBZ 3-1/8
HBZ 4-1/8
HBZ 4-1/4
HBZ 6-1/8
HBZ 6-1/4
M3CU2
M4CU2
M4CU4
M6CU2
M6CU4
3MO-6-2
4MO-6-2
4MO-6-4
6MO-6-2
6MO-6-4
3
4
4
6
6
1/8
1/8
1/4
1/8
1/4
36,3
36,5
39,3
38,5
41,1
15,3
16,1
16,1
17,7
17,7
15,3
15,3
17,7
15,3
17,7
22,6
23,6
26,4
24,6
25,9
12,0
12,0
14,0
14,0
14,0
HBZ 6-5/16
HBZ 8-1/4
HBZ 8-6
HBZ 10-1/8
HBZ 10-1/4
M6CU5
M8CU4
M8CU6
M10CU2
M10CU4
6MO-6-5
8MO-6-4
8MO-6-6
10MO-6-2
10MO-6-4
6
8
8
10
10
5/16
1/4
6
1/8
1/4
42,3
42,3
44,0
41,8
44,5
17,7
18,6
18,6
19,5
19,5
18,8
17,7
19,3
15,3
17,7
27,2
27,2
29,1
27,9
29,2
14,0
15,0
15,0
18,0
18,0
HBZ 10-3/8
HBZ 12-3/8
HBZ 12-1/2
HBZ 15-1/2
HBZ 16-3/8
HBZ 18-3/4
M10CU6
M12CU6
M12CU8
M15CU8
M16CU6
M18CU12
10MO-6-6
12MO-6-6
12MO-6-8
15MO-6-8
16MO-6-6
18MO-6-12
10
12
12
15
16
18
3/8
3/8
1/2
1/2
3/8
3/4
46,0
48,4
51,1
52,0
52,0
53,5
19,5
22,0
22,0
22,0
22,0
22,0
19,3
19,3
21,8
21,8
19,3
21,8
30,7
30,7
31,0
32,0
34,3
33,5
18,0
22,0
22,0
24,0
24,0
27,0
T1
MM
T2
INCH
C1
C2
W
HEX
NOTE: A, C1 and C2 dimensions are typical finger-tight.
HBZ, RU
Reducing Union
For fractional tube
A
C1
C2
T1
T2
W HEX
D
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
T1 TUBE
O.D.
T2 TUBE
O.D.
2-1 HBZ
3-1 HBZ
3-2 HBZ
4-1 HBZ
4-2 HBZ
2RU1
3RU1
3RU2
4RU1
4RU2
200-6-1
300-6-1
300-6-2
400-6-1
400-6-2
1/8
3/16
3/16
1/4
1/4
1/16
1/16
1/8
1/16
1/8
4-3 HBZ
5-2 HBZ
5-4 HBZ
6-1 HBZ
6-2 HBZ
4RU3
5RU2
5RU4
6RU1
6RU2
400-6-3
500-6-2
500-6-4
600-6-1
600-6-2
1/4
5/16
5/16
3/8
3/8
6-4 HBZ
6-5 HBZ
8-2 HBZ
8-4 HBZ
8-6 HBZ
6RU4
6RU5
8RU2
8RU4
8RU6
600-6-4
600-6-5
810-6-2
810-6-4
810-6-6
10-6 HBZ
10-8 HBZ
12-4 HBZ
12-6 HBZ
12-8 HBZ
10RU6
10RU8
12RU4
12RU6
12RU8
12-10 HBZ
16-8 HBZ
16-12 HBZ
12RU10
16RU8
16RU12
C1
C2
W
HEX
1.21
1.27
1.44
1.38
1.52
.81
.86
.92
.91
.97
.60
.64
.64
.70
.70
.43
.43
.60
.43
.60
7/16
7/16
7/16
1/2
1/2
3/16
1/8
1/4
1/16
1/8
1.55
1.58
1.67
1.44
1.61
1.00
1.03
1.08
1.00
1.06
.70
.73
.73
.76
.76
.64
.60
.70
.43
.60
1/2
9/16
9/16
5/8
5/8
3/8
3/8
1/2
1/2
1/2
1/4
5/16
1/8
1/4
3/8
1.71
1.75
1.75
1.85
1.91
1.13
1.16
1.09
1.16
1.22
.76
.76
.87
.87
.87
.70
.73
.60
.70
.76
5/8
5/8
13/16
13/16
13/16
1010-6-6
1010-6-8
1210-6-4
1210-6-6
1210-6-8
5/8
5/8
3/4
3/4
3/4
3/8
1/2
1/4
3/8
1/2
1.94
2.05
1.95
2.00
2.11
1.25
1.25
1.25
1.31
1.31
.87
.87
.87
.87
.87
.76
.87
.76
.76
.87
15/16
15/16
1-1/16
1-1/16
1-1/16
1210-6-10
1610-6-8
1610-6-12
3/4
1
1
5/8
1/2
3/4
2.11
2.39
2.39
1.31
1.50
1.50
.87
1.05
1.05
.87
.87
.87
1-1/16
1-3/8
1-3/8
HBZ, RUM
Reducing Union
For metric tube
A
C1
C2
T1
T2
W HEX
D
MILLIMETERS
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
HBZ 3-2
HBZ 6-2
HBZ 6-3
HBZ 6-4
HBZ 8-6
M3RUM2
M6RUM2
M6RUM3
M6RUM4
M8RUM6
3M0-6-2M
6MO-6-2M
6MO-6-3M
6MO-6-4M
8MO-6-6M
3
6
6
6
8
2
2
3
4
6
35,8
38,7
38,7
39,5
42,4
15,3
17,7
17,7
17,7
18,6
15,3
15,3
15,3
16,1
17,7
22,6
24,6
24,6
25,4
27,4
12,0
14,0
14,0
14,0
15,0
HBZ 10-6
HBZ 10-8
HBZ 12-6
HBZ 12-8
HBZ 12-10
M10RUM6
M10RUM8
M12RUM6
M12RUM8
M12RUM10
10MO-6-6M
10MO-6-8M
12MO-6-6M
12MO-6-8M
12MO-6-10M
10
10
12
12
12
6
8
6
8
10
44,5
44,5
47,0
47,8
48,7
19,5
19,5
22,0
22,0
22,0
17,7
18,6
17,7
18,6
19,5
29,4
29,4
29,4
30,2
31,0
18,0
18,0
22,0
22,0
22,0
HBZ 16-10
HBZ 16-12
HBZ 18-12
HBZ 25-18
HBZ 25-20
M16RUM10
M16RUM12
M18RUM12
M25RUM18
M25RUM20
16MO-6-10M
16MO-6-12M
18MO-6-12M
25MO-6-18M
25MO-6-20M
16
16
18
25
25
10
12
12
18
20
49,5
52,0
53,5
60,5
62,3
22,0
22,0
22,0
26,5
26,5
19,5
22,0
22,0
22,0
22,0
31,8
31,8
33,3
38,1
39,9
24,0
24,0
27,0
35,0
35,0
T1 TUBE
O.D.
T2 TUBE
O.D.
C1
C2
W
HEX
27
Tube to Tube Unions

A
WBZ, BC
Bulkhead Union
C1
For fractional tube
C2
W HEX
T2
T1
L1
L2
D
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
1-1 WBZ
2-2 WBZ
3-3 WBZ
4-2 WBZ
4-4 WBZ
5-5 WBZ
1BC1
2BC2
3BC3
4BC2
4BC4
5BC5
100-61
200-61
300-61
400-61-2
400-61
500-61
1/16
1/8
3/16
1/4
1/4
5/16
1.23
2.02
2.11
2.17
2.27
2.40
.43
.60
.64
.70
.70
.73
.94
1.50
1.59
1.03
1.69
1.81
.68
1.23
1.26
1.23
1.31
1.42
6-6 WBZ
8-8 WBZ
10-10 WBZ
12-12 WBZ
14-14 WBZ
16-16 WBZ
6BC6
8BC8
10BC10
12BC12
14BC14
16BC16
600-61
810-61
1010-61
1210-61
1410-61
1610-61
3/8
1/2
5/8
3/4
7/8
1
2.46
2.80
2.86
3.11
3.33
3.78
.76
.87
.87
.87
.87
1.05
1.88
2.00
2.06
2.31
2.53
2.81
1.44
1.65
1.68
1.87
2.09
2.27
L2
W
HEX
BULKHEAD
HOLE
DRILL SIZE
MAXIMUM
BULKHEAD
THICKNESS
.28
.34
.38
.41
.41
.44
.53
.97
1.00
.97
1.02
1.12
5/16
1/2
9/16
5/8
5/8
11/16
13/64
21/64
25/64
21/64
29/64
33/64
1/8
1/2
1/2
1/2
17/32
9/16
.47
.47
.47
.47
.47
.56
1.15
1.25
1.28
1.47
1.69
1.78
3/4
15/16
1-1/16
1-3/16
1-3/8
1-5/8
37/64
49/64
57/64
1-1/64
1-9/64
1-21/64
9/16
19/32
19/32
25/32
15/16
15/16
TUBE
O.D.
C1
C2
L1
NOTE: For reducer sizes call out short end first.

A, C1 and C2 dimensions are typical finger-tight.
For replacement bulkhead nuts, see Page 73, Part WLZ.
WBZ, BCM
Bulkhead Union
A
C1
For metric tube
C2
W HEX
T2
T1
L
D
MILLIMETERS
W
HEX
BHEAD
HOLE
DRILL
SIZE
MAX.
BHEAD
THICK.
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
WBZ 3-3
WBZ 4-4
WBZ 6-6
WBZ 8-8
WBZ 10-10
WBZ 12-12
BCM3
BCM4
BCM6
BCM8
BCM10
BCM12
3MO-61
4MO-61
6MO-61
8MO-61
10MO-61
12MO-61
3
4
6
8
10
12
51,3
53,7
57,9
61,0
63,6
71,0
15,3
16,1
17,7
18,6
19,5
22,0
31,2
32,0
33,7
36,0
37,0
41,9
38,2
40,5
42,9
46,0
48,4
50,8
24,6
25,4
26,2
28,5
29,4
31,8
14,0
14,0
16,0
18,0
22,0
24,0
8,3
9,9
11,5
13,1
16,3
19,5
12,7
12,7
10,2
11,2
11,2
12,7
WBZ 15-15
WBZ 16-16
WBZ 18-18
WBZ 20-20
WBZ 25-25
BCM15
BCM16
BCM18
BCM20
BCM25
15MO-61
16MO-61
18MO-61
20MO-61
25MO-61
15
16
18
20
25
72,5
72,6
78,9
88,2
95,8
22,0
22,0
22,0
22,0
26,5
42,6
42,6
47,4
51,0
54,4
52,3
52,4
58,7
68,0
71,4
32,5
32,5
37,3
40,9
42,2
27,0
27,0
30,0
35,0
41,0
22,5
22,5
26,0
29,0
33,8
12,7
12,7
16,8
19,0
24,0
TUBE
O.D.
C1
C2

For replacement bulkhead nuts, see Page 73, Part BN.
For reducer sizes call out short end first.
28
Tube to Tube Unions

DEBTA, DELTA
Dielectric Union
Adapter
DIELECTRIC
IDENTIFICATION
RING
T1 E BORE
T2
For fractional tube

includes nuts, machined
tube with molded ferrule,
preset ferrule, and dielectric identification ring
W1 HEX
CPI
ADAPTER
PART NO.
W2 HEX
INCHES
A-LOK
ADAPTER
PART NO.
TUBE END
T1
TUBE END
T2
E
BORE
W1
HEX
W2
HEX
3/8
1/2
1/2
5/8
2.08
2.58
.30
.38
11/16
7/8
7/8
1
6-8 DEBTA-SS 6-8 DELTA

8-10 DEBTA-SS 8-10 DELTA
NOTE: Makeup instructions included with parts in box when ordered as an Adapter only.
*Other end connectors available upon request.
DEBTA, DELTA
Dielectric Assembly
For fractional tube
includes dielectric union adapter
with assembled tube fitting unions
CPI ASSEMBLY
PART NO.
A-LOK ASSEMBLY
PART NO.
INCHES
*COMPRESSION
*COMPRESSION
ADAPTER
END CONNECTORS
4H DEBTA
6H DEBTA
8H DEBTA
4H DELTA
6H DELTA
8H DELTA
4.08
4.20
4.79
6-8 DELTA
6-8 DELTA
8-10 DELTA
6RU4/8RU4
6SC6/8RU6
8SC8/10RU8
*COMPRESSION
FEMALE PIPE
*COMPRESSION
FEMALE PIPE
ADAPTER
END CONNECTORS
4GDEBTA
6G DEBTA
8G DEBTA
4G DELTA
6G DELTA
8G DELTA
3.59
3.71
4.40
6-8 DELTA
6-8 DELTA
8-10 DELTA
6FSC4N/8FSC4N
6FSC6N/8FSC6N
8FSC8N/10FSC8N
*COMPRESSION
MALE PIPE
*COMPRESSION
MALE PIPE
ADAPTER
END CONNECTORS
4F DEBTA
6F DEBTA
8F DEBTA
4F DELTA
6F DELTA
8F DELTA
3.80
3.80
4.58
6-8 DELTA
6-8 DELTA
8-10 DELTA
6MSC4N/8MSC4N
6MSC6N/8MSC6N
8MSC8N/10MSC8N
Finger tight assembly dimensions.
EBZ, EE
Union Elbow
For fractional tube
C
L
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
1-1 EBZ
2-2 EBZ
3-3 EBZ
4-4 EBZ
5-5 EBZ
1EE1
2EE2
3EE3
4EE4
5EE5
100-9
200-9
300-9
400-9
500-9
1/16
1/8
3/16
1/4
5/16
6-6 EBZ
8-8 EBZ
10-10 EBZ
12-12 EBZ
14-14 EBZ
6EE6
8EE8
10EE10
12EE12
14EE14
600-9
810-9
1010-9
1210-9
1410-9
16-16 EBZ
20-20 EBZ
24-24 EBZ
32-32 EBZ
16EE16
20EE20
24EE24
32EE32
1610-9
2010-9
2410-9
3210-9
TUBE
O.D.
W
HEX
.71
.88
1.00
1.06
1.17
.56
.62
.74
.77
.88
3/8
3/8
1/2
1/2
5/8
3/8
1/2
5/8
3/4
7/8
1.20
1.42
1.43
1.56
1.76
.91
1.02
1.03
1.16
1.36
5/8
13/16
7/8
1-1/16
1-3/8
1
1-1/4
1-1/2
2
1.94
2.61
3.06
4.22
1.45
1.75
2.00
2.75
1-3/8
1-5/8
1-7/8
2-13/16
W HEX
29
Tube to Tube Unions

EBZ, EEM
Union Elbow
For metric tube
C
L
MILLIMETERS
INCH
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
EBZ 3-3
EBZ 4-4
EBZ 6-6
EBZ 8-8
EBZ 10-10
EEM3
EEM4
EEM6
EEM8
EEM10
3MO-9
4MO-9
6MO-9
8MO-9
10MO-9
3
4
6
8
10
22,3
25,4
27,0
28.8
31,5
15,7
18,8
19,6
21,3
23,9
3/8
1/2
1/2
9/16
11/16
EBZ 12-12
EBZ 14-14
EBZ 15-15
EBZ 16-16
EBZ 18-18
EEM12
EEM14
EEM15
EEM16
EEM18
12MO-9
14MO-9
15MO-9
16MO-9
18MO-9
12
14
15
16
18
36,0
38,1
38,0
38,0
39,8
25,9
28,0
27,9
27,9
29,7
13/16
15/16
15/16
15/16
1-1/16
EBZ 20-20
EBZ 22-22
EBZ 25-25
EEM20
EEM22
EEM25
20MO-9
22MO-9
25MO-9
20
22
25
44,6
44,6
49,1
34,5
34,5
36,8
1-3/8
1-3/8
1-3/8
TUBE
O.D.
W
HEX
W HEX
C1
EBZ, ELZ
L1
Drop Size
Elbows
For fractional tube
W HEX L
2
C2
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
3-2 EBZ
4-2 EBZ
5-2 EBZ
5-4 EBZ
6-2 EBZ
3-2 ELZ
4-2 ELZ
5-2 ELZ
5-4 ELZ
6-2 ELZ
300-9-2
400-9-2
500-9-2
500-9-4
600-9-2
3/16-1/8
1/4-1/8
5/16-1/8
5/16-1/4
3/8-1/8
.69
.77
.88
.88
.91
.96
1.06
1.17
1.17
1.20
.66
.70
.78
.85
.78
.92
.96
1.04
1.14
1.04
7/16
1/2
5/8
5/8
5/8
6-4 EBZ
6-5 EBZ
8-4 EBZ
8-5 EBZ
8-6 EBZ
6-4 ELZ
6-5 ELZ
8-4 ELZ
8-5 ELZ
8-6 ELZ
600-9-4
600-9-5
810-9-4
810-9-5
810-9-6
3/8-1/4
3/8-5/16
1/2-1/4
1/2-5/16
1/2-3/8
.91
.91
1.02
1.02
1.02
1.20
1.20
1.42
1.42
1.42
.85
.88
.96
.99
1.02
1.09
1.17
1.25
1.28
1.31
5/8
5/8
13/16
13/16
13/16
10-6 EBZ
10-8 EBZ
12-4 EBZ
12-6 EBZ
12-8 EBZ
10-6 ELZ
10-8 ELZ
12-4 ELZ
12-6 ELZ
12-8 ELZ
1010-9-6
1010-9-8
1210-9-4
1210-9-6
1210-9-8
5/8-3/8
5/8-1/2
3/4-1/4
3/4-3/8
3/4-1/2
1.03
1.03
1.16
1.16
1.16
1.43
1.43
1.56
1.56
1.56
1.03
1.03
1.09
1.16
1.16
1.32
1.43
1.38
1.45
1.56
7/8
7/8
1-1/16
1-1/16
1-1/16
14-4 EBZ
16-8 EBZ
16-12 EBZ
14-4 ELZ
16-8 ELZ
16-12 ELZ
1410-9-4
1610-9-8
1610-9-12
7/8-1/4
1-1/2
1-3/4
1.36
1.45
1.45
1.76
1.94
1.94
1.22
1.22
1.36
1.51
1.62
1.76
1-3/8
1-5/16
1-3/8
TUBE
O.D.
L1
C1
L2
C2
W
HEX
30
Tube to Tube Unions

A
JBZ, ET
Union Tee
C
L
For fractional tube

W HEX
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
1-1-1 JBZ
2-2-2 JBZ
3-3-3 JBZ
4-4-4 JBZ
5-5-5 JBZ
1ET1
2ET2
3ET3
4ET4
5ET5
100-3
200-3
300-3
400-3
500-3
1/16
1/8
3/16
1/4
5/16
1.42
1.76
2.00
2.12
2.34
6-6-6 JBZ
8-8-8 JBZ
10-10-10 JBZ
12-12-12 JBZ
14-14-14 JBZ
6ET6
8ET8
10ET10
12ET12
14ET14
600-3
810-3
1010-3
1210-3
1410-3
3/8
1/2
5/8
3/4
7/8
16-16-16 JBZ
20-20-20 JBZ
24-24-24 JBZ
32-32-32 JBZ
16ET16
20ET20
24ET24
32ET32
1610-3
2010-3
2410-3
3210-3
1
1-1/4
1-1/2
2
TUBE
O.D.
W
HEX
.71
.88
1.00
1.06
1.17
.56
.62
.74
.77
.88
3/8
3/8
1/2
1/2
5/8
2.40
2.84
2.86
3.12
3.52
1.20
1.42
1.43
1.56
1.76
.91
1.02
1.03
1.16
1.36
5/8
13/16
7/8
1-1/16
1-3/8
3.88
5.22
6.12
8.44
1.94
2.61
3.06
4.22
1.45
1.75
2.00
2.75
1-3/8
1-5/8
1-7/8
2-13/16
JBZ, ETM
Union Tee
C
L
For metric tube

W HEX
MILLIMETERS
INCH
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
W
HEX
JBZ 2-2-2
JBZ 3-3-3
JBZ 4-4-4
JBZ 6-6-6
JBZ 8-8-8
ETM2
ETM3
ETM4
ETM6
ETM8
2MO-3
3MO-3
4MO-3
6MO-3
8MO-3
2
3
4
6
8
44,7
44,7
50,8
53,9
59,7
22,3
22,3
25,4
27,0
29,9
15,7
15,7
18,8
19,6
22,4
3/8
3/8
1/2
1/2
5/8
JBZ 10-10-10
JBZ 12-12-12
JBZ 14-14-14
JBZ 15-15-15
JBZ 16-16-16
ETM10
ETM12
ETM14
ETM15
ETM16
10MO-3
12MO-3
14MO-3
15MO-3
16MO-3
10
12
14
15
16
63,0
72,0
77,6
77,6
77,6
31,5
36,0
38,8
38,8
38,8
23,9
25,9
28,7
28,7
28,7
11/16
13/16
1
1
1
JBZ 18-18-18
JBZ 20-20-20
JBZ 22-22-22
JBZ 25-25-25
ETM18
ETM20
ETM22
ETM25
18MO-3
20MO-3
22MO-3
25MO-3
18
20
22
25
79,5
89,3
89,3
98,3
38,8
44,6
44,6
49,1
29,7
34,5
34,5
36,8
1-1/16
1-3/8
1-3/8
1-3/8
31
Tube to Tube Unions

A
JBZ, JLZ
Drop Size Tees
C1
C2
L1
L2
For fractional tube

Eliminates the extra connection
when adapting with a tube
stub reducer
T1
T2
W HEX
L3
C3
T3
INCHES
CPI@
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
T1 TUBE
O.D.
T2 TUBE T3 TUBE
O.D.
O.D.
L1
C1
L2
C2
L3
C3
W
HEX
4-4-2 JBZ
6-6-4 JBZ
6-4-6 JBZ
6-4-4 JBZ
8-8-6 JBZ
4-4-2 JLZ
6-6-4 JLZ
6-4-6 JLZ
6-4-4 JLZ
8-8-6 JLZ
400-3-4-2
600-3-6-4
600-3-4-6
600-3-4-4
810-3-8-6
1/4
3/8
3/8
3/8
1/2
1/4
3/8
1/4
1/4
1/2
1/8
1/4
3/8
1/4
3/8
2.10
2.40
2.34
2.34
2.84
.76
.91
.91
.91
1.02
1.05
1.20
1.20
1.20
1.42
.76
.91
.85
.85
1.02
1.05
1.20
1.14
1.14
1.42
.70
.85
.91
.85
1.02
.96
1.14
1.20
1.14
1.31
1/2
5/8
5/8
5/8
13/16
8-8-4 JBZ
8-6-8 JBZ
8-4-8 JBZ
8-6-6 JBZ
8-4-4 JBZ
8-8-4 JLZ
8-6-8 JLZ
8-4-8 JLZ
8-6-6 JLZ
8-4-4 JLZ
810-3-8-4
810-3-6-8
810-3-4-8
810-3-6-6
810-3-4-4
1/2
1/2
1/2
1/2
1/2
1/2
3/8
1/4
3/8
1/4
1/4
1/2
1/2
3/8
1/4
2.84
2.73
2.67
2.73
2.67
1.02
1.02
1.02
1.02
1.02
1.42
1.42
1.42
1.42
1.42
1.02
1.02
.96
1.02
.96
1.42
1.31
1.25
1.31
1.25
.96
1.02
1.02
1.02
.96
1.25
1.42
1.42
1.31
1.25
13/16
13/16
13/16
13/16
13/16
10-10-8 JBZ
10-10-6 JBZ
10-8-8 JBZ
10-8-6 JBZ
10-6-6 JBZ
10-10-8 JLZ
10-10-6 JLZ
10-8-8 JLZ
10-8-6 JLZ
10-6-6 JLZ
1010-3-10-8
1010-3-10-6
1010-3-8-8
1010-3-8-6
1010-3-6-6
5/8
5/8
5/8
5/8
5/8
5/8
5/8
1/2
1/2
3/8
1/2
3/8
1/2
3/8
3/8
2.86
2.86
2.86
2.86
2.75
103
1.03
1.03
1.03
1.03
1.43
1.43
1.43
1.43
1.43
1.03
1.03
1.03
1.03
1.03
1.43
1.43
1.43
1.43
1.32
1.03
1.03
1.03
1.03
1.03
1.43
1.32
1.43
1.32
1.32
7/8
7/8
7/8
7/8
7/8
10-6-8 JBZ
12-12-10 JBZ
12-12-8 JBZ
12-12-6 JBZ
12-12-4 JBZ
10-6-8 JLZ
12-12-10 JLZ
12-12-8 JLZ
12-12-6 JLZ
12-12-4 JLZ
1010-3-6-8
1210-3-12-10
1210-3-12-8
1210-3-12-6
1210-3-12-4
5/8
3/4
3/4
3/4
3/4
3/8
3/4
3/4
3/4
3/4
1/2
5/8
1/2
3/8
1/4
2.75
3.12
3.12
3.12
3.12
1.03
1.16
1.16
1.16
1.16
1.43
1.56
1.56
1.56
1.56
1.03
1.16
1.16
1.16
1.16
1.32
1.56
1.56
1.56
1.56
1.03
1.16
1.16
1.16
1.09
1.43
1.56
1.56
1.45
1.38
7/8
1-1/16
1-1/16
1-1/16
1-1/16
12-10-10 JBZ
12-8-8 JBZ
12-6-6 JBZ
12-10-8 JBZ
12-10-6 JBZ
12-10-10 JLZ
12-8-8 JLZ
12-6-6 JLZ
12-10-8 JLZ
12-10-6 JLZ
1210-3-10-10
1210-3-8-8
1210-3-6-6
1210-3-10-8
1210-3-10-6
3/4
3/4
3/4
3/4
3/4
5/8
1/2
3/8
5/8
5/8
5/8
1/2
3/8
1/2
3/8
3.12
3.12
3.01
3.12
3.12
1.16
1.16
1.16
1.16
1.16
1.56
1.56
1.56
1.56
1.56
1.16
1.16
1.16
1.16
1.16
1.56
1.56
1.45
1.56
1.56
1.16
1.16
1.16
1.16
1.16
1.56
1.56
1.45
1.56
1.45
1-1/16
1-1/16
1-1/16
1-1/16
1-1/16
12-8-6 JBZ
14-14-6 JBZ
14-14-4 JBZ
14-12-12 JBZ
14-12-8 JBZ
12-8-6 JLZ
14-14-6 JLZ
14-14-4 JLZ
14-12-12 JLZ
14-12-8 JLZ
1210-3-8-6
1410-3-14-6
1410-3-14-4
1410-3-12-12
1410-3-12-8
3/4
7/8
7/8
7/8
7/8
1/2
7/8
7/8
3/4
3/4
3/8
3/8
1/4
3/4
1/2
3.12
3.52
3.52
3.52
3.52
1.16
1.36
1.36
1.36
1.36
1.56
1.76
1.76
1.76
1.76
1.16
1.36
1.36
1.36
1.36
1.56
1.76
1.76
1.76
1.76
1.16
1.36
1.30
1.36
1.36
1.45
1.65
1.59
1.76
1.76
1-1/16
1-3/8
1-3/8
1-3/8
1-3/8
14-12-6 JBZ
14-10-6 JBZ
14-8-12 JBZ
16-16-12 JBZ
16-16-10 JBZ
14-12-6 JLZ
14-10-6 JLZ
14-8-12 JLZ
16-16-12 JLZ
16-16-10 JLZ
1410-3-12-6
1410-3-10-6
1410-3-8-12
1610-3-16-12
1610-3-16-10
7/8
7/8
7/8
1
1
3/4
5/8
1/2
1
1
3/8
3/8
3/4
3/4
5/8
3.52
3.52
3.52
3.88
3.88
1.36
1.36
1.36
1.45
1.45
1.76
1.76
1.76
1.94
1.94
1.36
1.36
1.36
1.45
1.45
1.76
1.76
1.76
1.94
1.94
1.36
1.36
1.36
1.36
1.36
1.65
1.65
1.76
1.76
1.76
1-3/8
1-3/8
1-3/8
1-5/16
1-5/16
16-16-8 JBZ
16-16-6 JBZ
16-16-4 JBZ
16-12-16 JBZ
16-14-14 JBZ
16-16-8 JLZ
16-16-6 JLZ
16-16-4 JLZ
16-12-16 JLZ
16-14-14 JLZ
1610-3-16-8
1610-3-16-6
1610-3-16-4
1610-3-12-16
1610-3-14-14
1
1
1
1
1
1
1
1
3/4
7/8
1/2
3/8
1/4
1
7/8
3.88
3.88
3.88
3.70
3.70
1.45
1.45
1.45
1.45
1.45
1.94
1.94
1.94
1.94
1.94
1.45
1.45
1.45
1.36
1.36
1.94
1.94
1.94
1.76
1.76
1.36
1.36
1.30
1.45
1.36
1.76
1.65
1.59
1.94
1.76
1-5/16
1-5/16
1-5/16
1-5/16
1-5/16
16-14-12 JBZ
16-14-8 JBZ
16-14-6 JBZ
16-14-4 JBZ
16-16-14 JBZ
16-14-12 JLZ
16-14-8 JLZ
16-14-6 JLZ
16-14-4 JLZ
16-16-14 JLZ
1610-3-14-12
1610-3-14-8
1610-3-14-6
1610-3-14-4
1610-3-16-14
1
1
1
1
1
7/8
7/8
7/8
7/8
1
3/4
1/2
3/8
1/4
7/8
3.70
3.70
3.70
3.70
3.70
1.45
1.45
1.45
1.45
1.45
1.94
1.94
1.94
1.94
1.94
1.36
1.36
1.36
1.36
1.45
1.76
1.76
1.76
1.76
1.76
1.36
1.36
1.36
1.30
1.36
1.76
1.76
1.65
1.59
1.76
1-5/16
1-5/16
1-5/16
1-5/16
1-5/16
16-12-10 JBZ
16-12-8 JBZ
16-10-6 JBZ
16-8-16 JBZ
16-8-8 JBZ
16-12-10 JLZ
16-12-8 JLZ
16-10-6 JLZ
16-8-16 JLZ
16-8-8 JLZ
1610-3-12-10
1610-3-12-8
1610-3-10-6
1610-3-8-16
1610-3-8-8
1
1
1
1
1
3/4
3/4
5/8
1/2
1/2
5/8
1/2
3/8
1
1/2
3.70
3.70
3.70
3.70
3.70
1.45
1.45
1.45
1.45
1.45
1.94
1.94
1.94
1.94
1.94
1.36
1.36
1.36
1.36
1.36
1.76
1.76
1.76
1.76
1.76
1.36
1.36
1.36
1.45
1.36
1.76
1.76
1.65
1.94
1.76
1-5/16
1-5/16
1-5/16
1-5/16
1-5/16
16-8-6 JBZ
16-8-4 JBZ
16-6-6 JBZ
16-8-6 JLZ
16-8-4 JLZ
16-6-6 JLZ
1610-3-8-6
1610-3-8-4
1610-3-6-6
1
1
1
1/2
1/2
3/8
3/8
1/4
3/8
3.70
3.70
3.59
1.45
1.45
1.45
1.94
1.94
1.94
1.36
1.36
1.36
1.76
1.76
1.65
1.36
1.30
1.36
1.65
1.59
1.65
1-5/16
1-5/16
1-5/16
NOTE: C dimensions are typical finger-tight.
32
Tube to Tube Unions

KBZ, ECR
Union Cross
A
C
L
For fractional tube
W HEX
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
W
HEX
2 KBZ
3 KBZ
4 KBZ
5 KBZ
6 KBZ
2ECR2
3ECR3
4ECR4
5ECR5
6ECR6
200-4
300-4
400-4
500-4
600-4
1/8
3/16
1/4
5/16
3/8
1.84
1.92
2.02
2.28
2.26
.92
.95
1.01
1.14
1.13
.66
.69
.72
.84
.84
7/16
7/16
7/16
9/16
9/16
8 KBZ
10 KBZ
12 KBZ
14 KBZ
16 KBZ
8ECR8
10ECR10
12ECR12
14ECR14
16ECR16
810-4
1010-4
1210-4
1410-4
1610-4
1/2
5/8
3/4
7/8
1
2.74
2.86
3.12
3.52
3.86
1.37
1.43
1.56
1.76
1.93
.97
1.03
1.16
1.36
1.45
3/4
1-1/16
1-1/16
1-5/16
1-5/16
A
C
L
KBZ, ECRM
Union Cross
For metric tube
W HEX
MILLIMETERS
INCH
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
W
HEX
KBZ 3
KBZ4
KBZ 6
KBZ 8
KBZ 10
ECRM3
ECRM4
ECRM6
ECRM8
ECRM10
3MO-4
4MO-4
6MO-4
8MO-4
10MO-4
3
4
6
8
10
44,7
50,8
53,9
59,7
67,0
22,3
25,4
27,0
29,9
33,5
15,7
18,8
19,6
22,4
25,9
7/16
1/2
1/2
5/8
13/16
KBZ 12
KBZ 16
KBZ 18
ECRM12
ECRM16
ECRM18
12MO-4
16MO-4
18MO-4
12
16
18
72,0
74,0
76,6
36,0
37,0
38,3
25,9
26,9
28,2
13/16
15/16
1-1/16
33
Port Connectors
TRBZ, TUR
Tube End Reducer
A
K
For fractional tube
T1 TURNED
END TUBE O.D.
BORE
T2 MACHINED
END TUBE O.D.
W HEX
D
INCHES
T1 TURNED
END TUBE
O.D.
T2 MACHINE
END TUBE
O.D.
W
HEX
BORE
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
2-1 TRBZ
3-1 TRBZ
4-1 TRBZ
1-2 TRBZ
2-2 TRBZ
3-2 TRBZ
2TUR1*
3TUR1*
4TUR1
1TUR2*
2TUR2*
3TUR2*
100-R-2
100-R-3
100-R-4
200-R-1
200-R-2
200-R-3
1/8
3/16
1/4
1/16
1/8
3/16
1/16
1/16
1/16
1/8
1/8
1/8
1.10
1.13
1.24
1.18
1.34
1.35
.43
.43
.43
.60
.43
.60
.95
.98
1.09
.922
1.09
1.09
.53
.58
.63
.38
.54
.58
5/16
5/16
7/16
7/16
7/16
7/16
.05
.05
.05
.09
.07
.09
4-2 TRBZ
6-2 TRBZ
8-2 TRBZ
2-3 TRBZ
4-3 TRBZ
2-4 TRBZ
4TUR2
6TUR2
8TUR2
2TUR3*
4TUR3
2TUR4*
200-R-4
200-R-6
200-R-8
300-R-2
300-R-4
400-R-2
1/4
3/8
1/2
1/8
1/4
1/8
1/8
1/8
1/8
3/16
3/16
1/4
1.42
1.48
1.74
1.37
1.46
1.45
.60
.60
.60
.63
.63
.70
1.16
1.22
1.48
1.11
1.20
1.16
.63
.69
.91
.53
.63
.53
7/16
7/16
9/16
7/16
7/16
1/2
.09
.09
.09
.08
.13
.08
3-4 TRBZ
4-4 TRBZ
5-4 TRBZ
6-4 TRBZ
8-4 TRBZ
10-4 TRBZ
3TUR4*
4TUR4
5TUR4
6TUR4
8TUR4
10TUR4
400-R-3
400-R-4
400-R-5
400-R-6
400-R-8
400-R-10
3/16
1/4
5/16
3/8
1/2
5/8
1/4
1/4
1/4
1/4
1/4
1/4
1.48
1.54
1.57
1.60
1.82
1.89
.60
.70
.70
.70
.70
.70
1.19
1.25
1.28
1.31
1.53
1.60
.56
.63
.66
.69
.91
.97
1/2
1/2
1/2
1/2
9/16
11/16
.12
.19
.19
.19
.19
.19
12-4 TRBZ
6-5 TRBZ
8-5 TRBZ
4-6 TRBZ
6-6 TRBZ
8-6 TRBZ
12TUR4
6TUR5
8TUR5
4TUR6
6TUR6
8TUR6
400-R-12
500-R-6
500-R-8
600-R-4
600-R-6
600-R-8
3/4
3/8
1/2
1/4
3/8
1/2
1/4
5/16
5/16
3/8
3/8
3/8
1.88
1.65
1.87
1.63
1.70
1.91
.70
.73
.73
.76
.76
.76
1.59
1.36
1.58
1.34
1.41
1.62
.97
.69
.91
.63
.69
.91
13/16
9/16
9/16
5/8
5/8
5/8
.19
.25
.25
.19
.28
.28
10-6 TRBZ
12-6 TRBZ
4-8 TRBZ
6-8 TRBZ
10-8 TRBZ
12-8 TRBZ
10TUR6
12TUR6
4TUR8
6TUR8
10TUR8
12TUR8
600-R-10
600-R-12
810-R-4
810-R-6
810-R-10
810-R-12
5/8
3/4
1/4
3/8
5/8
3/4
3/8
3/8
1/2
1/2
1/2
1/2
1.98
1.98
1.77
1.84
2.12
2.12
.76
.76
.87
.87
.87
.87
1.69
1.69
1.37
1.44
1.72
1.72
.97
.97
.63
.69
.97
.97
11/16
13/16
13/16
13/16
13/16
13/16
.28
.28
.19
.19
.41
.41
16-8 TRBZ
12-10 TRBZ
14-10 TRBZ
16-10 TRBZ
8-12 TRBZ
16-12 TRBZ
16TUR8
12TUR10
14TUR10
16TUR10
8TUR12
16TUR12
810-R-16
1010-R-12
1010-R-14
1010-R-16
1210-R-8
1210-R-16
1
3/4
7/8
1
1/2
1
1/2
5/8
5/8
5/8
3/4
3/4
2.37
2.15
2.21
2.40
2.15
2.46
.87
.87
.87
.87
.87
.87
1.97
1.75
1.81
2.00
1.75
2.06
1.22
.97
1.03
1.22
.91
1.22
1-1/16
15/16
15/16
1-1/16
1-1/16
1-1/16
.41
.50
.50
.50
.39
.63
24-16-TRBZ
24-20 TRBZ
32-24 TRBZ
24TUR16
24TUR20
32TUR24
1610-R-24
2010-R-24
2410-R-32
1-1/2
1-1/2
2
1
1-1/4
1-1/2
3.519
4.10
5.17
1.05
1.52
1.52
3.03
3.23
4.10
2.05
2.05
2.74
1-5/8
1-7/8
2-1/4
.88
1.09
1.34

Size 4 and above tube stub is pre-grooved as standard. Generic (non-grooved) can be ordered through Quick Response Department.
*Size 1, 2, and 3 do not require a groove.
Add -Z6 for assembly of nuts and ferrules on the tube stub end.
Sizes 20, 24 require additional lubrication prior to assembly.
34
Port Connectors
A
TRBZ, TUCM
Tube End Converter
For metric tube
T1 TURNED
END TUBE O.D.
T2 MACHINED
END TUBE O.D.
W HEX
D
TUBE O.D.
MILLIMETERS
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
T1
INCH
T2
MM
W A/F
HEX
BORE
TRBZ3-2
TRBZ3-4
TRBZ6-4
TRBZ6-5
TRBZ6-6
2TUCM3
4TUCM3
4TUCM6
5TUCM6
6TUCM6
3MO-R-2
3MO-R-4
6MO-R-4
6MO-R-5
6MO-R-6
1/8
1/4
1/4
5/16
3/8
3
3
6
6
6
34,3
36,1
39,3
40,0
40,8
15,3
15,3
17,7
17,7
17,7
27,7
29,5
31,8
32,5
33,3
13,5
16,0
16,0
16,8
17,5
12,0
12,0
14,0
14,0
14,0
1,4
4,8
4,8
6,4
7,1
TRBZ6-8
TRBZ8-6
TRBZ10-6
TRBZ10-6
TRBZ10-8
8TUCM6
6TUCM8
8TUCM8
6TUCM10
8TUCM10
6MO-R-8
8MO-R-6
8MO-R-8
10MO-R-6
10MO-R-8
1/2
3/8
1/2
3/8
1/2
6
8
8
10
10
46,4
42,0
47,5
44,4
47,6
17,7
18,6
18,6
19,5
19,5
38,9
34,5
40,1
36,8
41,4
23,1
17,5
23,1
17,5
23,1
14,0
15,0
15,0
18,0
18,0
9,9
7,1
9,9
7,1
9,9
TRBZ12-8
TRBZ12-12
TRBZ18-12
8TUCM12
12TUCM12
12TUCM18
12MO-R-8
12MO-R-12
18MO-R-12
1/2
3/4
3/4
12
12
18
52,3
53,8
57,5
22,0
22,0
22,0
42,2
43,7
47,5
23,1
24,6
24,6
22,0
22,0
27,0
9,9
15,1
15,1

Tube stub is pre-grooved as standard. Generic (non-grooved) can be ordered through Quick Response Department.
Size 1, 2, and 3 do not require a groove.
35
Port Connectors
TRBZ, TURM
Tube End
Reducer
MILLIMETERS
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TRBZ 3-2
TRBZ 3-6
TRBZ 4-3
TRBZ 6-3
TRBZ 6-4
M3TURM2
M3TURM6
M4TURM3
M6TURM3
M6TURM4
2MO-R-3M
6MO-R-3M
3MO-R-4M
3MO-R-6M
4MO-R-6M
3
3
4
6
6
2
6
3
3
4
34,3
37,0
35,0
36,1
37,1
15,3
17,7
15,3
15,3
16,1
27,7
29,5
28,4
29,5
30,5
13,5
13,5
14,3
15,9
15,9
0,6
0,6
1,0
1,0
1,0
14,0
14,0
12,0
12,0
12,0
1,4
1,4
2,0
2,4
3,0
TRBZ 6-8
TRBZ 6-10
TRBZ 6-12
TRBZ 8-6
TRBZ 8-10
M6TURM8
M6TURM10
M6TURM12
M8TURM6
M8TURM10
8MO-R-6M
10MO-R-6M
12MO-R-6M
6MO-R-8M
10MO-R-8M
6
6
6
8
8
8
10
12
6
10
40,0
41,7
44,9
40,0
43,4
18,6
19,5
22,0
17,7
19,5
32,5
34,1
34,8
32,5
35,8
15,9
15,9
15,9
16,7
15,3
1,0
1,0
1,0
0,8
1,5
15,0
18,0
22,0
14,0
19,5
4,0
4,0
4,0
4,8
18,0
TRBZ 10-3
TRBZ 10-6
TRBZ 10-8
TRBZ 10-12
TRBZ 12-6
M10TURM3 3MO-R-10M
M10TURM6 6MO-R-10M
M10TURM8 8MO-R-10M
M10TURM12 12MO-R-10M
M12TURM6 6MO-R-12M
10
10
10
10
12
3
6
8
12
6
38,6
40,8
42,0
46,6
46,4
15,3
17,7
18,6
22,0
17,7
32,0
33,3
34,5
36,5
38,9
17,7
17,5
17,5
17,5
23,0
2,0
1,3
1,3
1,3
1,4
15,3
14,0
15,0
22,0
14,0
12,0
4,8
6,4
7,5
4,8
TRBZ 12-8
TRBZ 12-10
TRBZ 12-16
TRBZ 12-18
TRBZ 15-10
M12TURM8
M12TURM10
M12TURM16
M12TURM18
M15TURM10
8MO-R-12M
10MO-R-12M
16MO-R-12M
18MO-R-12M
10MO-R-15M
12
12
12
12
15
8
10
16
18
10
47,6
49,7
53,0
54,6
51,3
18,6
19,5
22,0
22,0
19,5
40,1
42,1
42,9
44,5
43,7
23,0
23,0
23,0
23,0
23,8
1,4
1,4
1,4
1,4
1,6
15,0
18,0
24,0
27,0
27,0
6,4
7,9
9,1
9,1
7,9
TRBZ 16-12
TRBZ 16-18
TRBZ 16-20
TRBZ 16-25
TRBZ 18-12
M16TURM12
M16TURM18
M16TURM20
M16TURM25
M18TURM12
12MO-R-16M
18MO-R-16M
20MO-R-16M
25MO-R-16M
12MO-R-18M
16
16
16
16
18
12
18
20
25
12
53,8
56,1
57,9
63,2
53,8
22,0
22,0
22,0
26,5
22,0
43,7
46,0
47,8
51,0
43,7
24,6
24,6
24,6
24,8
24,6
1,7
1,7
1,7
2,0
2,0
22,0
27,0
27,0
26,5
22,0
9,5
12,7
12,7
35,0
9,5
TRBZ 18-16
TRBZ 18-20
TRBZ 18-25
TRBZ 20-12
TRBZ 20-16
M18TURM16
M18TURM20
M18TURM25
M20TURM12
M20TURM16
16MO-R-18M
20MO-R-18M
25MO-R-18M
12MO-R-20M
16MO-R-20M
18
18
18
20
20
16
20
25
12
16
54,7
57,9
63,1
56,1
55,3
22,0
22,0
26,5
22,0
22,0
44,6
47,8
50,8
46,0
45,2
24,8
24,6
24,6
25,4
25,6
2,5
2,0
2,0
2,5
2,5
22,0
30,0
35,0
22,0
22,0
24,0
13,9
14,0
9,5
24,0
TRBZ 20-18
TRBZ 20-25
TRBZ 22-18
TRBZ 22-20
TRBZ 25-12
M20TURM18
M20TURM25
M22TURM18
M22TURM20
M25TURM12
18MO-R-20M
25MO-R-20M
18MO-R-22M
20MO-R-22M
12MO-R-25M
20
20
22
22
25
18
25
18
20
12
57,6
64,5
56,1
57,7
60,9
22,0
26,5
22,0
22,0
22,0
47,5
52,3
46,0
47,6
50,8
25,4
25,4
26,2
26,2
31,8
2,5
2,5
2,5
2,5
2,6
27,0
35,0
27,0
30,0
27,0
15,1
15,1
15,1
15,8
9,5
TRBZ 25-16
TRBZ 25-18
TRBZ 25-20
25
25
25
16
18
20
64,0
62,5
64,2
22,0
22,0
22,0
51,8
52,4
54,1
32,0
31,8
31,8
3,0
2,6
2,6
22,0
27,0
30,0
27,0
15,1
15,8
For metric tube
A
K
T1 TURNED
END TUBE O.D.
BORE
T2 MACHINED
END TUBE O.D.
W HEX
D
TUBE O.D.
T1
T2
W
HEX
BORE

Tube stub is pre-grooved as standard.
A
C
T2H2B2, TUBC
Tube End Bulkhead
Adapter
BORE
For fractional tube

W HEX
D
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
2-2 T2H2BZ
4-4 T2H2BZ
6-6 TH2HBZ
2TUBC2
4TUBC4
6TUBC6
200-R1-2
400-R1-4
600-R1-6
1/8
1/4
3/8
1.95
2.20
2.42
1.23
1.31
1.44
.97
1.02
1.15
8-8 T2H2BZ
8TUBC8
810-R1-8
1/2
2.87
1.65
1.25
BORE
W
HEX
.53
.63
.69
1.69
1.91
2.13
.093
.187
.281
1/2
5/8
3/4
.91
2.47
.406
15/16

36
Port Connectors
ZPC, PC
Port Connector
For fractional tube
A
K
BORE
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
1-1 ZPC
1-2 ZPC
1-4 ZPC
2-2 ZPC
2-4 ZPC
1PC1
1PC2
1PC4
2PC2
2PC4
101-PC
201-PC-1
401-PC-1
201-PC
401-PC-2
1/16
1/16-1/8
1/16-1/4
1/8
1/8-1/4
2-6 ZPC
3-3 ZPC
4-4 ZPC
4-6 ZPC
4-8 ZPC
6-6 ZPC
2PC6
3PC3
4PC4
4PC6
4PC8
6PC6
601-PC-2
301-PC
401-PC
601-PC-4
811-PC-4
601-PC
6-8 ZPC
8-8 ZPC
8-12 ZPC
12-12 ZPC
16-16 ZPC
6PC8
8PC8
8PC12
12PC12
16PC16
811-PC-6
811-PC
1211-PC-8
1211-PC
1611-PC
BORE
.63
.84
.91
.95
1.05
.44
.44
.44
.54
.54
.031
.031
.031
.078
.078
1/8-3/8
3/16
1/4
1/4-3/8
1/4-1/2
3/8
1.09
.981
1.07
1.15
1.36
1.16
.54
.67
.76
.64
.64
.84
.031
.116
.156
.156
.156
.281
3/8-1/2
1/2
1/2-3/4
3/4
1
1.40
1.59
1.72
1.65
2.12
.72
1.11
.91
1.16
1.44
.281
.375
.375
.578
.813

NOTE: Tube stub is pre-grooved as standard. (Size 1, 2, and 3 not grooved). Generic (non-grooved 4-16) can be ordered
through Quick Response Department.
The machined ferrule end (T2) requires only 1/4 turn from finger tight to assemble.
ZPC, PCM
Port Connector
For metric tube
A
K
T1
T2
MILLIMETERS
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
T2
BORE
ZPC 3-3
ZPC 6-6
ZPC 8-8
ZPC 10-10
ZPC 12-12
ZPC 16-16
ZPC 18-18
PCM3
PCM6
PCM8
PCM10
PCM12
PCM16
PCM18
3M1-PC
6M1-PC
8M1-PC
10M1-PC
12M1-PC
16M1-PC
18M1-PC
3
6
8
10
12
16
18
3
6
8
10
12
16
18
22,2
24,6
25,9
26,1
35,8
40,5
40,8
15,7
18,7
20,0
20,2
26,0
27,7
27,7
1,6
3,0
5,0
6,0
8,0
12,0
13,0
ZPC 3-6
ZPC 6-8
ZPC 6-10
ZPC 6-12
ZPC 8-10
ZPC 8-12
M3PCM6
M6PCM8
M6PCM10
M6PCM12
M8PCM10
M8PCM12
6M1-PC-3M
8M1-PC-6M
10M1-PC-6M
12M1-PC-6M
10M1-PC-8M
12M1-PC-8M
3
6
6
6
8
8
6
8
10
12
10
12
22,6
25,5
25,5
31,2
29,5
31,4
13,5
16,1
16,1
16,1
16,8
16,8
1,6
3,0
3,0
3,0
5,0
5,0
TUBE O.D.
T1

NOTE: Tube stub is pre-grooved as standard. (Size M2, M3, and M4 not grooved).
The machined ferrule end (T2) requires only 1/4 turn from finger tight to assemble.
37
Port Connectors
A
T2HF, MAN
NPT Tube End
Male Adapter
BORE
For fractional tube
W HEX
INCHES
TUBE
O.D.
NPT
PIPE
THREAD
CPI
PART NO.
A-LOK
PART NO.
NTERCHANGES
WITH
1-2 T2HF
2-2 T2HF
2-4 T2HF
3-2 T2HF
3-4 T2HF
1MA2N
2MA2N
2MA4N
3MA2N
3MA4N
1-TA-1-1
2-TA-1-2
2-TA-1-4
3-TA-1-2
3-TA-1-4
1/16
1/8
1/8
3/16
3/16
1/8
1/8
1/4
1/8
1/4
4-2 T2HF
4-4 T2HF
4-6 T2HF
4-8 T2HF
5-2 T2HF
4MA2N
4MA4N
4MA6N
4MA8N
5MA2N
4-TA-1-2
4-TA-1-4
4-TA-1-6
4-TA-1-8
5-TA-1-2
1/4
1/4
1/4
1/4
5/16
5-4 T2HF
5-6 T2HF
5-8 T2HF
6-2 T2HF
6-4 T2HF
5MA4N
5MA6N
5MA8N
6MA2N
6MA4N
5-TA-1-4
5-TA-1-6
5-TA-1-8
6-TA-1-2
6-TA-1-4
6-6 T2HF
6-8 T2HF
8-4 T2HF
8-6 T2HF
8-8 T2HF
6MA6N
6MA8N
8MA4N
8MA6N
8MA8N
10-8 T2HF
12-8 T2HF
12-12 T2HF
12-16 T2HF
16-12 T2HF
16-16 T2HF
20-20 T2HF
24-24 T2HF
32-32 T2HF
W
HEX
1.00
1.16
1.38
1.20
1.42
.38
.38
.56
.38
.56
.38
.54
.54
.58
.58
7/16
7/16
9/16
7/16
9/16
.031
.078
.078
.116
.116
1/8
1/4
3/8
1/2
1/8
1.25
1.46
1.49
1.71
1.29
.38
.56
.56
.75
.38
.63
.63
.63
.63
.66
7/16
9/16
11/16
7/8
7/16
.156
.156
.156
.156
.219
5/16
5/16
5/16
3/8
3/8
1/4
3/8
1/2
1/8
1/4
1.50
1.53
1.74
1.32
1.53
.56
.56
.75
.38
.56
.66
.66
.66
.69
.69
9/16
11/16
7/8
7/16
9/16
.219
.219
.219
.281
.281
6-TA-1-6
6-TA-1-8
8-TA-1-4
8-TA-1-6
8-TA-1-8
3/8
3/8
1/2
1/2
1/2
3/8
1/2
1/4
3/8
1/2
1.56
1.78
1.75
1.78
2.00
.56
.75
.56
.56
.75
.69
.69
.91
.91
.91
11/16
7/8
9/16
11/16
7/8
.281
.281
.281
.375
.375
10MA8N
12MA8N
12MA12N
12MA16N
16MA12N
10-TA-1-8
12-TA-1-8
12-TA-1-12
12-TA-1-16
16-TA-1-12
5/8
3/4
3/4
3/4
1
1/2
1/2
3/4
1
3/4
2.06
2.06
2.06
2.41
2.31
.75
.75
.75
.94
.75
.97
.97
.97
.97
1.22
7/8
7/8
1-1/16
1-3/8
1-1/16
.469
.469
.578
.813
.813
16MA16N
20MA20N
24MA24N
32MA32N
16-TA-1-16
20-TA-1-20
24-TA-1-24
32-TA-1-32
1
1-1/4
1-1/2
2
1
1-1/4
1-1/2
2
2.68
3.16
3.72
4.70
.94
.97
1.00
1.04
1.22
1.71
2.05
2.74
1-3/8
1-3/4
2-1/8
2-3/4
.813
1.00
1.25
1.72
BORE
NOTE: Add -Z6 for assembly of nuts and ferrules on the tube stub end.
Inch sizes 1, 2, and 3 and metric sizes 2, 3, and 4mm do not have grooves.
A
T2HF, MAR
BSPP Tube End
Male Adapter
BSPP
BSPP
For fractional tube
W HEX
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
BSPP
THREAD
HEX
W
BORE
2-2R T2HF
2-4R T2HF
4-2R T2HF
4-4R T2HF
6-2R T2HF
2MA2R
2MA4R
4MA2R
4MA4R
6MA2R
2TA-1-2RS
2TA-1-4RS
4TA-1-2RS
4TA-1-4RS
6TA-1-2RS
1/8
1/8
1/4
1/4
3/8
1/8
1/4
1/8
1/4
1/8
1.09
1.31
1.19
1.50
1.34
.53
.53
.63
.63
.69
.28
.44
.28
.44
.28
9/16
3/4
9/16
3/4
3/4
.05
.05
.16
.18
.05
6-4R T2HF
6-6R T2HF
6-8R T2HF
8-4R T2HF
8-6R T2HF
6MA4R
6MA6R
6MA8R
8MA4R
8MA6R
6TA-1-4RS
6TA-1-6RS
6TA-1-8RS
8TA-1-4RS
8TA-1-6RS
3/8
3/8
3/8
1/2
1/2
1/4
3/8
1/2
1/4
3/8
1.47
1.50
1.69
1.69
1.72
.69
.69
.69
.91
.91
.44
.44
.56
.44
.44
3/4
7/8
1-1/16
3/4
7/8
.25
.28
.28
.25
.31
8-8R T2HF
10-8R T2HF
12-12R T2HF
16-16R T2HF
8MA8R
10MA8R
12MA12R
16MA16R
8TA-1-8RS
10TA-1-8RS
12TA-1-12RS
16TA-1-16RS
1/2
5/8
3/4
1
1/2
1/2
3/4
1
1.94
1.97
2.09
2.53
.91
.97
.97
1.22
.56
.56
.63
.72
1-1/16
1-1/16
1-5/16
1-5/8
.39
.47
.578
.80
Bonded sealing washer must be used with this design, see p.72.
38
Port Connectors
T2HF, MAR
BSPP Tube End
Male Adapter
A
K
BSPP
BSPP
For metric tube
W HEX
MILLIMETERS
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
T2HF 3-1/8R
T2HF 4-1/8R
T2HF 6-1/8R
T2HF 6-1/4R
T2HF 8-1/4R
M3MA1/8R
M4MA1/8R
M6MA1/8R
M6MA1/4R
M8MA1/4R
3-MTA-1-2RS
4-MTA-1-2RS
6-MTA-1-2RS
6-MTA-1-4RS
8-MTA-1-4RS
3
4
6
6
8
1/8
1/8
1/8
1/4
1/4
31,0
31,8
33,3
38,1
38,9
13,5
14,3
15,9
15,9
16,7
0,6
1,0
1,0
1,0
0,8
7,1
7,1
7,1
11,2
11,2
13,7
13,7
13,7
17,8
17,8
14,0
14,0
14,0
19,0
19,0
1,8
2,0
4,0
4,0
6,4
T2HF 10-1/4R
T2HF 10-3/8R
T2HF 10-1/2R
T2HF 12-1/4R
T2HF 12-3/8R
M10MA1/4R
M10MA3/8R
M10MA1/2R
M12MA1/4R
M12MA3/8R
10-MTA-1-4RS
10-MTA-1-6RS
10-MTA-1-8RS
12-MTA-1-4RS
12-MTA-1-6RS
10
10
10
12
12
1/4
3/8
1/2
1/4
3/8
39,7
38,9
42,9
43,7
44,5
17,5
17,5
17,5
23,0
23,0
1,3
1,3
1,3
1,4
1,4
11,2
11,2
14,2
11,2
11,2
17,8
21,8
25,7
17,8
21,8
19,0
22,0
27,0
19,0
22,0
6,4
7,5
7,5
6,4
7,9
T2HF 12-1/2R
T2HF 16-1/2R
T2HF 18-3/4R
T2HF 20-3/4R
T2HF 25-1R
M12MA1/2R
M16MA1/2R
M18MA3/4R
M20MA3/4R
M25MA1R
12-MTA-1-8RS
16-MTA-1-8RS
18-MTA-1-12RS
20-MTA-1-12RS
25-MTA-1-16RS
12
16
18
20
25
1/2
1/2
3/4
3/4
1
49,2
50,8
53,2
54,0
65,1
23,0
24,6
24,6
25,4
31,8
1,4
1,7
2,0
2,5
2,6
14,2
14,2
16,0
16,0
18,3
25,7
25,7
31,8
31,8
38,6
27,0
27,0
33,0
33,0
41,0
9,1
11,9
14,0
15,1
19,8
TUBE
O.D.
BSPP
THREAD
W
HEX
BORE
NOTE: Tube stub is pre-grooved as standard. Generic (non-grooved) can be ordered through Quick Response Department.
Bonded sealing washer must be used with this design, see p. 72.
T2HF, MAR
BSPP Tube End Male
Adapter with ED Seal
A
K
R
BSPP
BSPP
For fractional tube

W HEX
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
4-4R-ED T2HF
4-6R-ED T2HF
8-4R-ED T2HF
8-6R-ED T2HF
8-8R-ED T2HF
4MA4R-ED
4MA6R-ED
8MA4R-ED
8MA6R-ED
8MA8R-ED
INCHES
TUBE
O.D.
BSPP
THREAD
1/4
1/4
1/2
1/2
1/2
1/4
3/8
1/4
3/8
1/2
1.50
1.50
1.75
1.78
1.94
.63
.63
.91
.91
.91
.47
.47
.47
.47
.55
.74
.86
.74
.86
1.04
W
HEX
3/4
3/4
3/4
7/8
1.1/16
BORE
.18
.18
.25
.31
.39
ED fitttings are supplied with sealing washers in Buna-N as standard, suitable for temperatures between 35C
and +100C (31F to +212F). Viton seals are available upon request which are suitable for temperatures
between 25C and +120C (13F to +248F).
39
Port Connectors
T2HF, MAR
BSPP Tube End Male
Adapter with ED Seal
A
K
BSPP
BSPP
For metric tube

W HEX
MILLIMETERS
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
BSPP
THREAD
W
HEX
BORE
T2HF 6-1/4R-ED
T2HF 6-1/2R-ED
T2HF 10-1/4R-ED
T2HF 10-1/2R-ED
T2HF 12-1/4R-ED
M6MA1/4R-ED
M6MA1/2R-ED
M10MA1/4R-ED
M10MA1/2R-ED
M12MA1/4R-ED
6
6
10
10
12
1/4
1/2
1/4
1/2
1/4
36,6
42,7
38,1
44,2
43,7
15,9
15,9
17,5
17,5
23,0
7,9
14,0
11,9
14,0
11,9
19,0
27,0
19,0
27,0
19,0
4,0
4,0
6,4
7,5
6,4
T2HF 12-3/8R-ED M12MA3/8R-ED

T2HF 12-1/2R-ED M12MA1/2R-ED
12
12
3/8
1/2
45,0
49,8
23,0
23,0
11,9
14,0
22,0
27,0
7,9
9,1
ED fittings are supplied with sealing washers in Buna-N as standard, suitable for temperatures between 35C
and +100C (31F to +212F). Viton seals are available upon request which are suitable for temperatures
between 25C and +120C (13F to +248F).
T2HF, MAN
NPT Male Adapter
A
K
For metric tube

W HEX
MILLIMETERS
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
T2HF 3-1/8
T2HF 4-1/8
T2HF 6-1/8
T2HF 6-1/4
T2HF 6-3/8
M3MA1/8N
M4MA1/8N
M6MA1/8N
M6MA1/4N
M6MA3/8N
3-MTA-1-2
4-MTA-1-2
6-MTA-1-2
6-MTA-1-4
6-MTA-1-6
3
4
6
6
6
1/8
1/8
1/8
1/4
3/8
29,4
29,4
31,0
35,7
36,5
13,5
14,3
15,9
15,9
16,1
9,7
9,7
9,7
14,2
14,2
12,0
12,0
12,0
14,0
18,0
1,8
2,0
4,0
4,0
3,0
T2HF 6-1/2
T2HF 8-1/4
T2HF 8-3/8
T2HF 10-1/4
T2HF 10-3/8
M6MA1/2N
M8MA1/4N
M8MA3/8N
M10MA1/4N
M10MA3/8N
6-MTA-1-8
8-MTA-1-4
8-MTA-1-6
10-MTA-1-4
10-MTA-1-6
6
8
8
10
10
1/2
1/4
3/8
1/4
3/8
42,1
37,3
38,1
38,1
43,7
16,1
16,7
16,7
17,5
17,5
19,1
14,2
14,2
14,2
14,2
22,0
14,0
12,0
14,0
18,0
3,0
6,4
6,4
7,1
7,5
T2HF 10-1/2
T2HF 12-1/4
T2HF 12-3/8
T2HF 12-1/2
T2HF 16-1/2
M10MA1/2N
M12MA1/4N
M12MA3/8N
M12MA1/2N
M16MA1/2N
10-MTA-1-8
12-MTA-1-4
12-MTA-1-6
12-MTA-1-8
16-MTA-1-8
10
12
12
12
16
1/2
1/4
3/8
1/2
1/2
44,5
43,7
44,5
49,2
50,8
17,5
23,0
23,0
23,0
24,6
19,1
14,2
14,2
19,1
19,1
22,0
14,0
27,0
22,0
22,0
7,5
7,1
9,1
9,1
12,7
T2HF 16-3/4
T2HF 18-1/2
T2HF 18-3/4
T2HF 20-1/2
T2HF 20-3/4
T2HF 25-1
M16MA3/4N
M18MA1/2N
M18MA3/4N
M20MA1/2N
M20MA3/4N
M25MA1N
16-MTA-1-12
18-MTA-1-8
18-MTA-1-12
20-MTA-1-8
20-MTA-1-12
25-MTA-1-16
16
18
18
20
20
25
3/4
1/2
3/4
1/2
3/4
1
51,6
50,8
51,6
51,8
52,4
65,9
24,6
24,6
24,6
25,6
25,4
31,8
19,1
19,1
19,1
19,1
19,1
23,9
27,0
22,0
27,0
22,0
27,0
35,0
12,7
12,7
14,0
15,0
15,1
19,8
TUBE
O.D.
NPT
THREAD
W
HEX
BORE
NOTE: Tube stub is pre-grooved as standard. Generic (non-grooved) can be ordered through
Quick Response Department.
40
Port Connectors
A
T2HF, MAK
BSP Taper Male Adapter
BSP
BSP
For fractional tube
W HEX
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
4-2K T2HF
4-4K T2HF
4-6K T2HF
4-8K T2HF
5-2 T2HF
5-4 T2HF
4MA2K
4MA4K
4MA6K
4MA8K
5MA2K
5MA4K
4-TA-1-2RT
4-TA-1-4RT
4-TA-1-6RT
4-TA-1-8RT
5-TA-1-2RT
5-TA-1-4RT
1/4
1/4
1/4
1/4
5/16
5/16
1/8
1/4
3/8
1/2
1/8
1/4
1.25
1.46
1.44
1.66
1.29
1.50
.63
.63
.63
.63
.66
.66
.38
.56
.56
.75
.38
.56
7/16
9/16
11/16
7/8
7/16
9/16
.156
.156
.156
.219
.219
.219
6-4 T2HF
6-6 T2HF
6-8 T2HF
8-4 T2HF
8-6 T2HF
8-8 T2HF
10-8 T2HF
6MA4K
6MA6K
6MA8K
8MA4K
8MA6K
8MA8K
10MA8K
6-TA-1-4RT
6-TA-1-6RT
6-TA-1-8RT
8-TA-1-4RT
8-TA-1-6RT
8-TA-1-8RT
10-TA-1-8RT
3/8
3/8
3/8
1/2
1/2
1/2
5/8
1/4
3/8
1/2
1/4
3/8
1/2
1/2
1.50
1.50
1.72
1.72
1.75
1.94
2.06
.69
.69
.69
.91
.91
.91
.97
.56
.56
.75
.56
.56
.75
.75
9/16
11/16
7/8
9/16
11/16
7/8
7/8
.281
.281
.281
.375
.375
.375
.469
TUBE
O.D.
BSPT
THREAD
W
HEX
BORE
T2HF, MAK
BSP Taper Male Adapter
A
K
BSP
BSP
For metric tube
W HEX
MILLIMETERS
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
T2HF 3-1/8K
T2HF 4-1/8K
T2HF 6-1/8K
T2HF 6-1/4K
T2HF 8-1/4K
M3MA1/8K
M4MA1/8K
M6MA1/8K
M6MA1/4K
M8MA1/4K
3-MTA-1-2RT
4-MTA-1-2RT
6-MTA-1-2RT
6-MTA-1-4RT
8-MTA-1-4RT
3
4
6
6
8
1/8
1/8
1/8
1/4
1/4
29,4
29,4
31,0
35,7
37,3
13,5
14,3
15,9
15,9
16,7
9,7
9,7
9,7
14,2
14,2
12,0
12,0
12,0
14,0
14,0
1,8
2,0
4,0
4,0
6,4
T2HF 8-3/8K
T2HF 10-1/4K
T2HF 10-3/8K
T2HF 10-1/2K
T2HF 12-1/4K
M8MA3/8K
M10MA1/4K
M10MA3/8K
M10MA1/2K
M12MA1/4K
8-MTA-1-6RT
10-MTA-1-4RT
10-MTA-1-6RT
10-MTA-1-8RT
12-MTA-1-4RT
8
10
10
10
12
3/8
1/4
3/8
1/2
1/4
38,3
38,1
38,1
44,5
43,7
16,8
17,5
17,5
17,5
23,0
14,2
14,2
14,2
19,1
14,2
18,0
14,0
18,0
22,0
14,0
5,0
7,1
7,5
7,5
7,1
T2HF 12-3/8K
T2HF 12-1/2K
T2HF 16-1/2K
T2HF 18-3/4K
T2HF 20-3/4K
T2H 25-1K
M12MA3/8K
M12MA1/2K
M16MA1/2K
M18MA3/4K
M20MA3/4K
M25MA1K
12-MTA-1-6RT
12-MTA-1-8RT
16-MTA-1-8RT
18-MTA-1-12RT
20-MTA-1-12RT
25-MTA-1-16RT
12
12
16
18
20
25
3/8
1/2
1/2
3/4
3/4
1
44,5
49,2
50,8
51,6
52,4
65,9
23,0
23,0
24,6
24,6
25,4
31,8
14,2
19,1
19,1
19,1
19,1
23,9
18,0
22,0
22,0
27,0
27,0
35,0
9,1
9,1
12,7
14,0
15,1
19,8
TUBE
O.D.
BSPT
THREAD
W
HEX
BORE
41
Port Connectors
T2HOA, TUHA
Tube End to
SAE Straight
Thread Adapter
For fractional tube
A
R
STRAIGHT
THREAD
O-RING
INCHES
CPI
PART NO.
A-LOK
PART NO.
6-4 T2HOA
6TUHA4
6-8 T2HOA
6TUHA8
8-6 T2HOA
8TUHA6
10-10 T2HOA 10TUHA10
*24-24 T2HOA 24TUHA24
INTERCHANGES
WITH
T
TUBE
O.D.
STRAIGHT
THREAD
SIZE
W
HEX
O-RING
APR
UNIFORM
DASH NO.
6-TA-1-4ST
6-TA-1-8ST
8-TA-1-6ST
10-TA-1-10ST
24-TA-1-24ST
3/8
3/8
1/2
5/8
1-1/2
7/16-20
3/4-16
9/16-18
7/8-14
1-7/8-12
1.46
1.59
1.74
1.94
3.28
.69
.69
.91
.91
2.05
.36
.44
.39
.50
.59
9/16
7/8
11/16
1
2-1/8
3-904
3-908
3-906
3-910
3-924
* Sizes 20, 24 and 32 are preassembled with nut and ferrules.

A dimension is typical finger-tight.
Size 24 requires additional lubrication prior to assembly.
Parts are supplied with Buna-N o-rings as standard. For Viton o-rings, add the suffix -VO.
Other o-rings available upon request.
W HEX
Add -Z6 for assembly of nuts and ferrules

on the tube stub end.
T2HG, FAN
Tube End NPT
Female Adapter
For fractional tube
A
K
BORE
W HEX
INCHES
CPI
PART NO.
I
A-LOK
PART NO.
NTERCHANGES
WITH
TUBE
O.D.
NPT PIPE
THREAD
1-2 T2HG
2-2 T2HG
2-4 T2HG
3-2 T2HG
3-4 T2HG
1FA2N
2FA2N
2FA4N
3FA2N
3FA4N
1-TA-7-2
2-TA-7-2
2-TA-7-4
3-TA-7-2
3-TA-7-4
1/16
1/8
1/8
3/16
3/16
1/8
1/8
1/4
1/8
1/4
1.07
1.23
1.38
1.25
1.42
4-2 T2HG
4-4 T2HG
4-6 T2HG
4-8 T2HG
5-2 T2HG
4FA2N
4FA4N
4FA6N
4FA8N
5FA2N
4-TA-7-2
4-TA-7-4
4-TA-7-6
4-TA-7-8
5-TA-7-2
1/4
1/4
1/4
1/4
5/16
1/8
1/4
3/8
1/2
1/8
5-4 T2HG
5-6 T2HG
6-2 T2HG
6-4 T2HG
6-6 T2HG
5FA4N
5FA6N
6FA2N
6FA4N
6FA6N
5-TA-7-4
5-TA-7-6
6-TA-7-2
6-TA-7-4
6-TA-7-6
5/16
5/16
3/8
3/8
3/8
6-8 T2HG
8-4 T2HG
8-6 T2HG
8-8 T2HG
10-6 T2HG
6FA8N
8FA4N
8FA6N
8FA8N
10FA6N
6-TA-7-8
8-TA-7-4
8-TA-7-6
8-TA-7-8
10-TA-7-6
10-8 T2HG
12-8 T2HG
12-12 T2HG
12-16 T2HG
14-12 T2HG
10FA8N
12FA8N
12FA12N
12FA16N
14FA12N
16-12 T2HG
16-16 T2HG
20-20 T2HG
24-24 T2HG
32-32 T2HG
16FA12N
16FA16N
20FA20N
24FA24N
32FA32N
W
HEX
BORE
.34
.53
.53
.56
.56
9/16
9/16
3/4
9/16
3/4
.031
.093
.093
.116
.116
1.31
1.47
1.56
1.80
1.34
.63
.63
.63
.63
.66
9/16
3/4
7/8
1-1/16
9/16
.188
.188
.188
.188
.219
1/4
3/8
1/8
1/4
3/8
1.50
1.59
1.36
1.55
1.59
.66
.66
.69
.69
.69
3/4
7/8
9/16
3/4
7/8
.219
.219
.281
.281
.281
3/8
1/2
1/2
1/2
5/8
1/2
1/4
3/8
1/2
3/8
1.84
1.72
1.80
2.10
1.86
.69
.91
.91
.91
.97
1-1/16
3/4
7/8
1-1/16
7/8
.281
.391
.391
.390
.469
10-TA-7-8
12-TA-7-8
12-TA-7-12
12-TA-7-16
14-TA-7-12
5/8
3/4
3/4
3/4
7/8
1/2
1/2
3/4
1
3/4
2.09
2.10
2.16
2.30
2.22
.97
.97
.97
.97
1.02
1-1/16
1-1/16
1-1/4
1-5/8
1-5/16
.469
.578
.578
.578
.578
16-TA-7-12
16-TA-7-16
20-TA-7-20
24-TA-7-24
32-TA-7-32
1
1
1-1/4
1-1/2
2
3/4
1
1-1/4
1-1/2
2
2.41
2.54
3.06
3.50
4.23
1.22
1.22
1.71
2.05
2.74
1-5/16
1-5/8
2-1/8
2-3/8
2-7/8
.813
.813
1.000
1.25
1.72
NOTE: Tube stub is pre-grooved as standard.

Generic (non-grooved) can be ordered through Quick Response Department.
42
Port Connectors
T2HG, FAN
Tube End
NPT Female
Adapter
For metric tube
A
K
BORE
W HEX
MILLIMETERS
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
NPT
THREAD
W
HEX
BORE
T2HG 3-1/8
T2HG 4-1/8
T2HG 6-1/8
T2HG 6-1/4
T2HG 8-1/8
M3FA1/8N
M4FA1/8N
M6FA1/8N
M6FA1/4N
M8FA1/8N
3-MTA-7-2
4-MTA-7-2
6-MTA-7-2
6-MTA-7-4
8-MTA-7-2
3
4
6
6
8
1/8
1/8
1/8
1/4
1/8
31,3
29,4
29,4
34,1
35,5
13,5
14,3
15,9
15,9
16,7
14,0
14,0
14,0
19,0
14,0
1,3
2,0
4,0
4,0
6,4
T2HG 8-1/4
T2HG 8-3/8
T2HG 10-1/4
T2HG 10-3/8
T2HG 10-1/2
M8FA1/4N
M8FA3/8N
M10FA1/4N
M10FA3/8N
M10FA1/2N
8-MTA-7-4
8-MTA-7-6
10-MTA-7-4
10-MTA-7-6
10-MTA-7-8
8
8
10
10
10
1/4
3/8
1/4
3/8
1/2
35,1
36,5
37,3
37,3
42,1
16,7
16,7
17,5
17,5
17,5
19,0
22,0
19,0
22,0
27,0
6,4
6,4
7,5
7,5
7,5
T2HG 12-1/4
T2HG 12-3/8
T2HG 12-1/2
T2HG 16-1/2
T2HG 18-3/4
M12FA1/4N
M12FA3/8N
M12FA1/2N
M16FA1/2N
M18FA3/4N
12-MTA-7-4
12-MTA-7-6
12-MTA-7-8
16-MTA-7-8
18-MTA-7-12
12
12
12
16
18
1/4
3/8
1/2
1/2
3/4
41,3
42,9
47,6
49,2
52,4
23,0
23,0
23,0
24,6
24,6
19,0
22,0
27,0
27,0
33,0
9,1
9,1
9,1
12,7
14,0
T2HG 20-1/2
T2HG 20-3/4
T2G 25-1
M20FA1/2N
M20FA3/4N
M25FA1N
20-MTA-7-8
20-MTA-7-12
25-MTA-7-16
20
20
25
1/2
3/4
1
50,0
53,2
66,7
25,6
25,4
31,8
27,0
33,0
41,0
15,0
15,1
19,8
CPI
PART NO.

T2HG, FAK
BSP Taper
Female
Adapter
For fractional
tube
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
4-2K T2HG
4-4K T2HG
6-4K T2HG
6-6K T2HG
8-4K T2HG
8-6K T2HG
8-8K T2HG
4FA2K
4FA4K
6FA4K
6FA6K
8FA4K
8FA6K
8FA8K
4-TR-7-2RT
4-TR-7-4RT
6-TR-7-4RT
6-TR-7-6RT
8-TR-7-4RT
8-TR-7-6RT
8-TR-7-8RT
INCHES
TUBE
O.D.
BSPT
THREAD
W
HEX
BORE
1/4
1/4
3/8
3/8
1/2
1/2
1/2
1/8-28
1/4-19
1/4-19
3/8-19
1/4-19
3/8-19
1/2-14
1.31
1.48
1.56
1.63
1.83
1.89
2.14
.64
.64
.72
.72
.98
.98
.98
9/16
3/4
3/4
7/8
3/4
7/8
1-1/16
.156
.156
.281
.281
.375
.375
.375

A
K
BORE
W HEX
T2HG, FAK
BSP Taper
Female
Adapter
For metric tube
A
K
BORE
MILLIMETERS
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
BSPT
THREAD
W
HEX
BORE
T2HG 3-1/8K
T2HG 4-1/8K
T2HG 6-1/8K
T2HG 8-1/4K
T2HG 10-1/4K
M3FA1/8K
M4FA1/8K
M6FA1/8K
M8FA1/4K
M10FA1/4K
3-MTA-7-2RT
4-MTA-7-2RT
6-MTA-7-2RT
8-MTA-7-4RT
10-MTA-7-4RT
3
4
6
8
10
1/8
1/8
1/8
1/4
1/4
27,8
28,6
30,2
39,1
36,5
13,5
14,3
15,9
16,7
17,5
14,0
14,0
14,0
19,0
19,0
1,8
2,0
4,0
6,4
7,5
T2HG 10-3/8K
T2HG 10-1/2K
T2HG 12-1/4K
T2HG 12-3/8K
T2HG 12-1/2K
M10FA3/8K
M10FA1/2K
M12FA1/4K
M12FA3/8K
M12FA1/2K
10-MTA-7-6RT
10-MTA-7-8RT
12-MTA-7-4RT
12-MTA-7-6RT
12-MTA-7-8RT
10
10
12
12
12
3/8
1/2
1/4
3/8
1/2
31,8
41,3
40,5
43,7
46,8
17,5
17,5
23,0
23,0
23,0
22,0
27,0
19,0
22,0
27,0
7,5
7,5
9,1
9,1
9,1
T2HG 16-1/2K
T2HG 18-3/4K
T2HG 20-3/4K
T2HG 25-1K
M16FA1/2K
M18FA3/4K
M20FA3/4K
M25FA1K
16-MTA-7-8RT
18-MTA-7-12RT
20-MTA-7-12RT
25-MTA-7-16RT
16
18
20
25
1/2
3/4
3/4
1
48,4
51,6
52,4
66,7
24,6
24,6
25,4
31,8
27,0
32,0
32,0
41,0
12,7
14,0
15,1
19,8
4-NOTE: Tube stub is pre-grooved as standard.

W HEX
43
Port Connectors
T2HG, FAR
BSPP Female
Adapter
For fractional tube
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
BSPP
THREAD
W
HEX
BORE
4-4R T2HG
6-6R T2HG
8-8R T2HG
4FA4R
6FA6R
8FA8R
4-TA-7-4RP
6-TA-7-6RP
8-TA-7-8RP
1/4
3/8
1/2
1/4
3/8
1/2
1.47
1.53
1.91
.63
.69
.91
3/4
7/8
1-1/16
.18
.28
.39
BSPP
NOTE: Copper washer must be used for this design.

A
K
BSPP
BORE
W HEX
T2HG, FAR
BSPP Female
Adapter
For metric tube
BSPP
A
K
BSPP
BORE
MILLIMETERS
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
BSPP
THREAD
W
HEX
BORE
T2HG 3-1/8R
T2HG 3-1/4R
T2HG 4-1/8R
T2HG 6-1/8R
T2HG 6-1/4R
T2HG 8-1/4R
M3FA1/8R
M3FA1/4R
M4FA1/8R
M6FA1/8R
M6FA1/4R
M8FA1/4R
3-MTA-7-2RP
3-MTA-7-4RP
4-MTA-7-2RP
6-MTA-7-4RP
6-MTA-7-4RP
8-MTA-7-4RP
3
3
4
6
6
8
1/8
1/4
1/8
1/8
1/4
1/4
28,6
28,6
29,4
31,0
37,3
38,1
13,5
13,7
14,3
15,9
15,9
16,7
14,0
19,0
14,0
14,0
19,0
19,0
1,8
1,6
2,0
4,0
4,0
6,4
T2HG 10-1/4R
T2HG 10-1/2R
T2HG 12-3/8R
T2HG 12-1/2R
T2HG 16-1/2R
M10FA1/4R
M10FA1/2R
M12FA3/8R
M12FA1/2R
M16FA1/2R
10-MTA-7-4RP
10-MTA-7-8RP
12-MTA-7-6RP
12-MTA-7-8RP
16-MTA-7-8RP
10
10
12
12
16
1/4
1/2
3/8
1/2
1/2
38,9
43,7
44,5
48,4
50,0
17,5
17,5
23,0
23,0
24,6
19,0
27,0
22,0
27,0
27,0
7,5
7,5
9,1
9,1
12,7
T2HG 18-3/4R
T2HG 20-3/4R
T2HG 25-1R
M18FA3/4R
M20FA3/4R
M25FA1R
18-MTA-7-12RP
20-MTA-7-12RP
25-MTA-7-16RP
18
20
25
3/4
3/4
1
53,2
54,0
67,5
24,6
25,4
31,8
33,0
33,0
41,0
14,0
15,1
19,8
NOTE: Copper washer must be used for this design.

W HEX
P2T2, P2TU
Push-Lok to
Tube Adapter
For fractional tube
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
T1 TUBE
O.D.
T2 HOSE
SIZE
W
HEX
4-4 P2T2
6-6 P2T2
8-8 P2T2
4-4 P2TU
6-6 P2TU
8-8 P2TU
PB4-TA4
PB6-TA6
PB8-TA8
1/4
3/8
1/2
4
6
8
1.80
2.02
2.42
.64
.72
.98
7/16
9/16
11/16
NOTE: Drawing does not show Push-Lok collar.

A
K
T2 MACHINED
END TUBE
O.D.
T1 TURNED
END TUBE
O.D.
W HEX
44
Port Connectors
P2HF
Push-Lok to
Male Adapter
For fractional tube
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
4-4 P2HF
6-6 P2HF
8-8 P2HF
4-4 P2HF
6-6 P2HF
8-8 P2HF
PB4-PM4
PB6-PM6
PB8-PM8
INCHES
T2 NPT PIPE
T1
THREAD
HOSE SIZE
1/4
3/8
1/2
-4
-6
-8
NOTE: Drawing does not show Push-Lok collar.
W
HEX
1.65
1.828
2.194
.80
.95
1.10
.56
.56
.75
9/16
11/16
7/8
A
R
T2
T1
W HEX
P2BZ6, P2LZ6
Push-Lok to
CPI/A-LOK
For fractional tube
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
T2 TUBE
O.D.
T1 HOSE
SIZE
4-4 P2BZ6
6-6 P2BZ6
8-8 P2BZ6
4-4 P2LZ6
6-6 P2LZ6
8-8 P2LZ6
PB4-TA4
PB6-TA6
PB8-TA8
1/4
3/8
1/2
4
6
8
1.77
1.98
2.42
W
HEX
.72
.78
1.03
7/16
9/16
11/16
NOTE: A dimension is typical finger-tight.

Drawing does not show Push-Lok collar. Assembly includes nut and ferrules.
A
K
T1
T2
W HEX
ZP2
INCHES
Push-Lok to
Port Connector
For fractional tube
CPI
PART NO.
A-LOK
PART NO.
T1 HOSE
SIZE
T2 PORT
SIZE
4-6 ZP2
4-6 ZP2
3/8
1.40
.80

NOTE: Drawing does not show Push-Lok collar and size 6 A-LOK nut.
A
B
T1
T2
45
Port Connectors
LJFBZ, LJF
Lapped Joint
Tube Adapters
For metric tube
MILLIMETERS
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
FLANGE SIZE
LJFBZ10-5
LJFBZ10-9
LJFBZ12-5
LJFBZ12-9
M10LJF-5
M10LJF-9
M12LJF-5
M12LJF-9
10M0-1-0005
10M0-1-0006
10
10
12
12
DN15( 2"NB)
DN15(12"NB)
DN15(12"NB)
DN15(12"NB)
83,0
83,0
85,0
85,0
34,5
34,5
34,5
34,5
75,5
75,5
75,4
75,4
6,5
6,5
6,5
6,5
NOTE: Groove on flange diameter indicates rough finish.
SURFACE FINISH
Smooth
Rough
Smooth
Rough
3,2-6,3 Ra
6,3-12,5 Ra
3,2-6,3 Ra
6,3-12,5 Ra
The lapped joint tube adaptor is a fitting designed to be used with a lap joint flange which enables a direct hook-up to the
instrument tube from the process line.
The compression fitting is incorporated into the body of the adaptor thus the number of components needed for hook-up is
reduced. It is therefore cost efficient as well as space saving.
Note
Groove on flange
diameter indicates
rough finish.
The face of the fitting forms the gasket face of the flange and comes with either a smooth or serrated surface finish.
Adapters to suit other tube and flange sizes may be furnished upon request.
L
A
ZH2X
DP Transmitter
Calibration Adapters
TRANSMITTER TYPE
PARKER PART NO.
INTERCHANGES WITH
(1) Rosemount/Foxboro
(2) Honeywell
4-2 ZH2LX-SS-D950373
4-2 ZH2LX-SS-D940336
SS-400-1-0253
SS-400-1-0257
For fractional tube

Parker CPI/A-LOK adapters
connect directly to the bleed port
of a differential pressure transmitter so that the calibration
process can be simplified. Two
sizes of adapters (1/4-28 Thd.,
5/16-24 Thd.) are available to fit
the vent ports of Rosemount,
Honeywell, and Foxboro DP
transmitters. Both adapters are
available in 316SS.
J
1/4
TUBE
STRAIGHT
THREAD
HEX
(1) 5/16-24
(2) 1/4-28
2.32
1.75
1.00
.80
.70
.70
2.03
1.46
.24
.47
.60
.60
.25
.20
.06
.03
.41
1/2
1/2
A
D
9/16
HEX
INCHES
B
H
E
G
F
C
9/16 1/4 TUBE

HEX
E
STRAIGHT THREAD
1/2 BODY HEX
H
G
F
C
STRAIGHT THREAD
1/2 BODY HEX
Calibration Adapter For

Honeywell DP Transmitters
Calibration Adapter For

Rosemount/Foxboro DP Transmitters
46
37 Flare (AN) to A-LOK

X6HBZ6, X6TU
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
W
HEX
2-2 X6HBZ6
4-4 X6HBZ6
6-6 X6HBZ6
2X6TU2
4X6TU4
6X6TU6
200-A-2 ANF
400-A-4 ANF
600-A-6 ANF
1/8
1/4
3/8
.88
.96
1.07
3/8
9/16
11/16
8-8 X6HBZ6
12-12 X6HBZ6
16-16 X6HBZ6
8X6TU8
12X6TU12
16X6TU16
810-A-8 ANF
1210-A-12ANF
1610-A-16ANF
1/2
3/4
1
1.37
1.49
1.80
7/8
1-1/4
1-1/2
37 Flare (AN) to
CPI/A-LOK
For fractional tube
W HEX
XHBZ, XASC
37 Flare
Connector
For fractional tube
A
D
B
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
FLARE
END
TUBE
O.D.
2-1 XHBZ
2-2 XHBZ
4-2 XHBZ
3-3 XHBZ
4-4 XHBZ
2XASC1
2XASC2
4XASC2
3XASC3
4XASC4
100-6-2 AN
200-6-2 AN
200-6-4 AN
300-6-3 AN
400-6-4 AN
1/8
1/8
1/4
3/16
1/4
1/16
1/8
1/8
3/16
1/4
1.07
1.28
1.39
1.32
1.48
.45
.45
.55
.48
.55
5-5 XHBZ
4-6 XHBZ
6-6 XHBZ
8-8 XHBZ
10-10 XHBZ
5XASC5
4XASC6
6XASC6
8XASC8
10XASC10
500-6-5 AN
600-6-4 AN
600-6-6 AN
810-6-8 AN
1010-6-10 AN
5/16
1/4
3/8
1/2
5/8
5/16
3/8
3/8
1/2
5/8
1.52
1.56
1.56
1.81
1.93
12-12 XHBZ
16-16 XHBZ
12XASC12
16XASC16
1210-6-12 AN
1610-6-16 AN
3/4
1
3/4
1
2.11
2.43
W
HEX
.43
.60
.60
.64
.70
.92
1.02
1.13
1.06
1.19
7/16
7/16
1/2
7/16
1/2
.55
.55
.56
.66
.76
.73
.76
.76
.87
.87
1.22
1.27
1.27
1.41
1.53
9/16
5/8
5/8
13/16
15/16
.86
.91
.87
1.05
1.70
1.94
1-1/8
1-3/8
W HEX
XH2BZ, XABC
37 Flare
Bulkhead
Connector
For fractional tube
A
D
B
C
L
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
FLARE
END
TUBE
O.D.
W
HEX
2-2 XH2BZ
3-3 XH2BZ
4-2 XH2BZ
4-4 XH2BZ
5-5 XH2BZ
2XABC2
4XABC2
3XABC3
4XABC4
5XABC5
200-61-2 AN
200-61-4 AN
300-61-3 AN
400-61-4 AN
500-61-5 AN
1/8
1/4
3/16
1/4
5/16
1/8
1/8
3/16
1/4
5/16
1.91
2.04
1.98
2.12
2.21
1.65
1.78
1.71
1.83
1.92
1.23
1.23
1.26
1.31
1.41
.97
.97
1.00
1.02
1.12
.45
.55
.48
.55
.55
1/2
5/8
9/16
5/8
11/16
4-6 XH2BZ
6-6 XH2BZ
8-8 XH2BZ
10-10 XH2BZ
12-12 XH2BZ
4XABC6
600-61-4 AN
6XABC6
600-61-6 AN
8XABC8
810-61-8 AN
10XABC10 1010-61-10 AN
12XABC12 1210-61-12 AN
1/4
3/8
1/2
5/8
3/4
3/8
3/8
1/2
5/8
3/4
2.25
2.25
2.59
2.74
3.11
1.96
1.96
2.19
2.34
2.71
1.44
1.44
1.65
1.68
1.87
1.15
1.15
1.25
1.28
1.47
.55
.56
.66
.76
.86
3/4
3/4
15/16
1-1/16
1-3/16
16-16 XH2BZ
16XABC16 1610-61-16 AN
3.65
3.16
2.27
1.78
.91
1-9/16

For bulkhead hole drill size and maximum bulkhead thickness, see Page 28, Part BC
W HEX
47
Tube to O Ring Seal

Introduction
BSPP / SAE Straight Thread
Fittings Installation
Procedure
SAE
WLN LOCK NUT
1. Lubricate O ring with a lubricant that is

compatible with the system.
2. Screw fitting into the straight thread port until
the metal back-up washer contacts the face
of the port.
3. Position the fitting by backing it out no more
than one turn.
4. Hold the fitting in position and tighten the
locknut until the washer contacts the face
of the port. (See torque chart.)
NOTE: WLN Lock Nuts are ordered separately
by size and part number. Refer to page 73.
WASHER
O RING
Straight Port
Size
Torque
(in-lbs)
4
6
8
10
12
16
20
24
245 10
630 25
1150 50
1550 50
2050 50
3000 50
3400 100
4500 100
BSPP
Adjustable Port
(F.F.F.T.)
Torque
(in-lbs)
(F.F.F.T)
1.0 .25
1.5 .25
1.5 .25
1.5 .25
1.5 .25
1.5 .25
1.5 .25
1.5 .25
200 10
400 10
640 10
1125 50
1450 50
2150 50
2800 100
3450 100
1.5 25
1.5 25
1.5 25
1.5 25
1.5 25
1.5 25
2.0 25
2.0 25
WLN LOCK NUT

WASHER
RETAINING RING
FITTING
BODY
FEMALE PORT
NOTES
Restrain fitting body on adjustables if necessary in installation.

Values in charts are for assemblies with O-ring lubricated.
Use upper limits of torque ranges for stainless steel fittings.
*L5N LOCK NUT
Face Seal O Ring Fittings

Installation Procedure
The O ring requires a smooth, flat seating surface.This surface
must be perpendicular to the axis of the threads.
1. Turn the O ring seal fitting in the port until finger tight.
2. The squeezing effect on the O ring can be felt during the last
1/4 turn.
3. Snug lightly with a wrench.
*Typical Application
The fitting can be adapted as a bulkhead fitting on thin wall tanks or
vessels, eliminating welding, brazing or threading. Simply order the
L5N locknut to take advantage of this option.
PORT
SIZE
Notes
Standard O rings are Buna-N material. For other O rings, state
material after the part number.
L5N locknuts are ordered separately by size and part number. Refer
to page 73.
STRAIGHT THREAD
MACHINE LENGTH
L5N LOCKNUT
THICKNESS
MAXIMUM TANK
WALL THICKNESS
2
3
4
5
6
8
.297
.297
.360
.360
.391
.438
.219
.219
.250
.250
.265
.312
.078 = 5/64
.078 = 5/64
.109 = 7/65
.109 = 7/64
.125 = 1/8
.125 = 1/8
10
12
14
16
.500
.594
.594
.594
.360
.406
.406
.406
.140 = 9/64
.188 = 3/16
.188 = 3/16
.188 = 3/16
O-rings used with SAE/MS straight threads are Buna-N. Other O-ring materials are available on request. Lubricate O-ring with a lubricant compatible with the system fluid, environment and O-ring material.
48
Tube to O Ring Seal

A
D
ZHBA, M1SC
Male Connector to SAE
Straight Thread
For fractional tube

W HEX
INCHES
O RING
W
HEX
O-RING
AS
UNIFORM
DASH NO.
.43
.60
.60
.64
.70
.77
.92
1.06
.94
1.05
.30
.30
.39
.30
.36
7/16
7/16
11/16
1/2
9/16
3-902
3-902
3-906
3-903
3-904
1.40
1.48
1.60
1.37
1.40
.70
.70
.70
.73
.76
1.11
1.19
1.31
1.08
1.11
.39
.44
.50
.36
.36
11/16
7/8
1
5/8
5/8
3-906
3-908
3-910
3-905
3-904
9/16-18
3/4-16
7/8-14
9/16-18
3/4-16
1.46
1.54
1.67
1.54
1.65
.76
.76
.76
.87
.87
1.17
1.25
1.38
1.14
1.25
.39
.44
.50
.39
.44
11/16
7/8
1.00
7/8
7/8
3-906
3-908
3-910
3-906
3-908
1/2
5/8
3/4
3/4
7/8
1-1/16-12
7/8-14
7/8-14
1-1/16-12
1-3/16-12
1.93
1.78
1.68
1.93
1.93
.87
.87
.87
.87
.87
1.53
1.38
1.28
1.53
1.53
.59
.50
.50
.59
.59
1-1/4
1
1-1/8
1-1/4
1-3/8
3-912
3-910
3-910
3-912
3-914
1
1
1-1/4
1-1/2
2
1-1/16-12
1-5/16-12
1-5/8-12
1-7/8-12
2-1/2-12
2.12
2.15
2.59
3.05
4.00
1.05
1.04
1.52
1.77
2.47
1.63
1.66
1.82
1.99
2.53
.59
.59
.59
.59
.59
1-3/8
1-1/2
1-7/8
2-1/8
2-3/4
3-912
3-916
3-920
3-924
3-932
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
1-2 ZHBA
2-2 ZHBA
2-6 ZHBA
3-3 ZHBA
4-4 ZHBA
1M1SC2
2M1SC2
2M1SC6
3M1SC3
4M1SC4
100-1-2 ST
200-1-2 ST
200-1-6 ST
300-1-3 ST
400-1-4 ST
1/16
1/8
1/8
3/16
1/4
5/16-24
5/16-24
9/16-18
3/8-24
7/16-20
.92
1.18
1.35
1.20
1.34
4-6 ZHBA
4-8 ZHBA
4-10 ZHBA
5-5 ZHBA
6-4 ZHBA
4M1SC6
4M1SC8
4M1SC10
5M1SC5
6M1SC4
400-1-6 ST
400-1-8 ST
400-1-10 ST
500-1-5 ST
600-1-4 ST
1/4
1/4
1/4
5/16
3/8
9/16-18
3/4-16
7/8-14
1/2-20
7/16-20
6-6 ZHBA
6-8 ZHBA
6-10 ZHBA
8-6 ZHBA
8-8 ZHBA
6M1SC6
6M1SC8
6M1SC10
8M1SC6
8M1SC8
600-1-6 ST
600-1-8 ST
600-1-10 ST
810-1-6 ST
810-1-8 ST
3/8
3/8
3/8
1/2
1/2
8-12 ZHBA
10-10 ZHBA
12-10 ZHBA
12-12 ZHBA
12-14 ZHBA
8M1SC12
10M1SC10
12M1SC10
12M1SC12
14M1SC14
810-1-12 ST
1010-1-10 ST
1210-1-10 ST
1210-1-12 ST
1410-1-14 ST
16-12 ZHBA
16-16 ZHBA
20-20 ZHBA
24-24 ZHBA
32-32 ZHBA
16M1SC12
16M1SC16
20M1SC20
24M1SC24
32M1SC32
1610-1-12 ST
1610-1-16 ST
2010-1-20 ST
2410-1-24 ST
3210-1-32 ST
TUBE
O.D.
STRAIGHT
THREAD
SIZE

For use with SAE J.1926/1 port can also be used with MS-16142 port.
Parts are supplied with Buna-N o-rings as standard. For Viton o-rings, add the suffix -VO. Other o-rings available upon request.
49
Tube to O Ring Seal

C
C5BZ, M5SEL
W HEX
Male SAE Straight

Thread Elbow
For fractional tube
H
WLN
BACKUP WASHER
O RING
STRAIGHT
THREAD
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
4-4 C5BZ
6-6 C5BZ
8-8 C5BZ
12-12 C5BZ
16-16 C5BZ
24-24 C5BZ
4M5SEL4
6M5SEL6
8M5SEL8
12M5SEL12
16M5SEL16
24M5SEL24
400-2-4ST
600-2-6ST
810-2-8ST
1210-2-12ST
1610-2-16ST
2410-2-24ST
TUBE
O.D.
STRAIGHT
THREAD
SIZE
1/4
3/8
1/2
3/4
1
1-1/2
7/16-20
9/16-18
3/4-16
1-1/16-12
1-5/16-12
1-7/8-12
W
HEX
O-RING
ARP
UNIFORM
DASH NO.
1.12
1.26
1.48
1.63
1.87
1.13
1.27
1.48
1.92
2.11
2.33
.83
.97
1.08
1.23
1.38
2.00
.83
.84
.97
1.28
1.28
1.16
1/2
9/16
3/4
1-1/16
1-5/16
1-7/8
3-904
3-906
3-908
3-912
3-916
3-924

Size 24 requires additional lubrication prior to assembly.
CBZ, MSEL (R)
W HEX
BSPP Male Elbow

(Positionable)
For fractional tube
BSPP
BSPP
H
L4N
R
O RING
STRAIGHT
THREAD
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
BSPP
THREAD
4-2R CBZ
4-4R CBZ
6-4R CBZ
6-6R CBZ
8-8R CBZ
4MSEL2R
4MSEL4R
6MSEL4R
6MSEL6R
8MSEL4R
400-2-2PR
400-2-4PR
600-2-4PR
600-2-6PR
810-2-4PR
1/4
1/4
3/8
3/8
1/2
1/8-28
1/4-19
1/4-19
3/8-19
1/4-19
8-6R CBZ
8-8R CBZ
10-10R CBZ
12-8R CBZ
12-12R CBZ
8MSEL6R
8MSEL8R
10MSEL8R
12MSEL8R
12MSEL12R
810-2-6PR
810-2-8PR
1010-2-8PR
1210-2-8PR
1210-2-12PR
1/2
1/2
5/8
3/4
3/4
16-12R CBZ
16-16R CBZ
16MSEL12R
16MSEL16R
1610-2-12PR
1610-2-16PR
1
1
W
HEX
1.14
1.31
1.31
1.50
1.50
1.25
1.27
1.27
1.46
1.38
.85
.85
1.02
1.02
1.10
.81
.83
.83
.83
.83
9/16
9/16
9/16
3/4
7/8
3/8-19
1/2-14
1/2-14
1/2-14
3/4-14
1.48
1.50
1.50
1.57
1.57
1.46
1.70
1.81
1.81
1.92
1.10
1.10
1.10
1.17
1.17
.85
1.09
1.09
1.09
1.20
7/8
7/8
1-1/16
1-1/16
1-1/16
3/4-14
1-11
1.94
1.94
2.11
2.11
1.45
1.45
1.20
1.20
1-5/16
1-5/16

Connects fractional tube to female ISO parallel thread.
50
Tube to O Ring Seal

A
R5BZ, M5RT
H
L
Male Run Tee SAE

Straight Thread
R
STRAIGHT
THREAD
For fractional tube

W HEX
WLN
O RING
BACKUP WASHER
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
4-4-4 R5BZ
4M5RT4
400-3TST
6-6-6 R5BZ
6M5RT6
600-3TST
8-8-8 R5BZ
8M5RT8
810-3TST
12-12-12 R5BZ 12M5RT12 1210-3TST
16-16-16 R5BZ 16M5RT16 1610-3TST
TUBE
O.D.
STRAIGHT
THREAD
SIZE
1/4
3/8
1/2
3/4
1
7/16-20
9/16-18
3/4-16
1-1/16-12
1-5/16-12
2.25
2.53
3.59
3.55
3.98
1.12
1.26
1.48
1.63
1.87
W
HEX
O-RING
ARP
UNIFORM
DASH NO.
1.13
1.27
1.48
1.92
2.11
.83
.97
1.08
1.23
1.38
.83
.84
.97
1.28
1.28
7/16
9/16
3/4
1-1/16
1-5/16
3-904
3-906
3-908
3-912
3-916

RBZ, MRT (R)
H
L
BSPP
BSPP
BSPP Male Run Tee

(Positionable)
For fractional tube
L4N
O RING
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
BSPP
THREAD
4-2R-4 RBZ
4-4R-4 RBZ
6-6R-6 RBZ
8-6R-8 RBZ
8-8R-8 RBZ
4MRT2R
4MRT4R
6MRT6R
8MRT8R
8MRT8R
400-3TRT
400-3-4TRT
600-3TRT
810-3TRT
810-3-8TRT
1/4
1/4
3/8
1/2
1/2
1/8-28
1/4-19
1/4-19
3/8-19
1/2-14
10-8R-10 RBZ
12-8R-12 RBZ
12-12R-12 RBZ
16-16R-16 RBZ
10MRT8R
12MRT8R
12MRT12R
16MRT16R
1010-3TRT
1210-3-8TRT
1210-3TRT
1610-3TRT
5/8
3/4
3/4
1
1/2-14
1/2-14
3/4-14
1-11
W
HEX
1.14
1.14
1.31
1.50
1.50
1.25
1.28
1.27
1.36
1.71
.85
.85
1.02
1.10
1.10
.81
.83
.83
.85
1.09
9/16
9/16
9/16
7/8
7/8
1.50
1.567
1.57
1.94
1.81
1.81
1.92
2.11
1.10
1.17
1.17
1.45
1.09
1.09
1.20
1.20
1-1/16
1-1/16
1-1/16
1-5/16

51
Tube to O Ring Seal

A
C
S5BZ, M5BT
Male Branch Tee

SAE Straight Thread
For fractional tube
W HEX
H
WLN
R
O RING
BACKUP
WASHER
STRAIGHT
THREAD
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
4-4 S5BZ
6-6 S5BZ
8-8 S5BZ
12-12 S5BZ
16-16 S5BZ
4M5BT4
6M5BT6
8M5BT8
12M5BT12
16M5BT16
400-3TTS
600-3TTS
810-3TTS
1210-3TTS
1610-3TTS
TUBE
O.D.
STRAIGHT
THREAD
SIZE
W
HEX
O-RING
ARP
UNIFORM
DASH NO.
1/4
3/8
1/2
3/4
1
7/16-20
9/16-18
3/4-16
1-1/16-12
1-5/16-12
2.24
2.52
2.96
3.26
3.74
1.12
1.26
1.48
1.63
1.87
1.13
1.27
1.48
1.92
2.11
.83
.97
1.08
1.23
1.38
.83
.84
.97
1.28
1.28
7/16
9/16
3/4
1-1/16
1-5/16
3-904
3-906
3-908
3-912
3-916

C
L
SBZ, MBT (R)

BSPP Male Branch
Tee (Positionable)
BSPP
BSPP
For fractional tube
W HEX
H
R
L4N
O RING
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
BSPP
THREAD
W
HEX
4-4-2R SBZ
4-4-4R SBZ
6-6-4R SBZ
8-8-6R SBZ
8-8-8R SBZ
4MBT2R
4MBT4R
6MBT4R
8MBT6R
8MBT8R
400-3TTR
400-3-4TTR
600-3TTR
810-3TTR
810-3-8TTR
1/4
1/4
3/8
1/2
1/2
1/8-28
1/4-19
1/4-19
3/8-19
1/2-14
1.14
1.14
1.31
1.50
1.50
1.25
1.27
1.27
1.36
1.71
.85
.85
1.02
1.10
1.10
.81
.83
.83
.85
1.09
9/16
9/16
9/16
7/8
7/8
10-10-8R SBZ
12-12-8R SBZ
12-12-12R SBZ
16-16-16R SBZ
10MBT8R
12MBT8R
12MBT12R
16MBT16R
1010-3TTR
1210-3-8TTR
1210-3-TTR
1610-3TTR
5/8
3/4
3/4
1
1/2-14
1/2-14
3/4-14
1-11
1.50
1.57
1.57
1.94
1.81
1.81
1.92
2.11
1.10
1.17
1.17
1.45
1.09
1.09
1.20
1.20
1-1/16
1-1/16
1-1/16
1-5/16

Connects fractional tube to female ISO parallel thread.
52
Tube to O Ring Seal

A
D
ZH3BA, ZH3LA
Long Male Connector

SAE/MS Straight Thread
For fractional tube
O RING
W HEX
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
T
TUBE
O.D.
4-4 ZH3BA
6-6 ZH3BA
8-8 ZH3BA
12-12 ZH3BA
16-16 ZH3BA
4-4 ZH3LA
6-6 ZH3LA
8-8 ZH3LA
12-12 ZH3LA
16-16 ZH3LA
400-1L-4ST
600-1L-6ST
810-1L-8ST
1210-1L-12ST
1610-1L-16ST
1/4
3/8
1/2
3/4
1
S-SAE/MS
THREAD
SIZE
7/16-20
9/16-18
3/4-16
1-1/16-12
1-5/16-12
2.26
2.48
3.01
3.88
4.34
.36
.39
.44
.59
.59
.70
.76
.86
.86
1.04
E
MIN.
OPENING
W
HEX
ST
O-RING
UNIFORM
SIZE NO.
1.97
2.19
2.58
3.48
3.86
.19
.28
.41
.62
.88
9/16
11/16
7/8
1-1/4
1-1/2
-904
-906
-908
-912
-916

C
L
V5BZ, M5VEL
W HEX
45 Positionable Male Elbow

SAE/MS Straight Thread
For fractional tube
H
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
STRAIGHT
TUBE
O.D.
4-4 V5BZ
6-6 V5BZ
8-8 V5BZ
12-12 V5BZ
16-16 V5BZ
4M5VEL4
6M5VEL6
8M5VEL8
12M5VEL12
16M5VEL16
400-5-4ST
600-5-6ST
810-5-8ST
1210-5-12ST
1610-5-16ST
1/4
3/8
1/2
3/4
1
THREAD
SIZE
7/16-20
9/16-18
3/4-16
1-1/16-12
1-5/16-12
.93
1.01
1.15
1.63
1.87
1.02
1.27
1.48
1.92
2.11
W
HEX
O-RING
UNIFORM
SIZE
NUMBER
.65
.72
.75
1.23
1.39
.75
.77
.88
1.16
1.16
7/16
9/16
3/4
1-1/16
1-5/16
3-904
3-906
3-908
3-912
3-916

Adapts to SAE J1926 straight thread boss and MS16142 boss.
53
Tube to O Ring Seal

A
D
ZHBA5, M2SC
Male Connector to
O Ring Straight Thread
For fractional tube

STRAIGHT
THREAD
W HEX
INCHES
TUBE
O.D.
STRAIGHT
THREAD
SIZE
X DIA.
W
HEX
O-RING
ARP
UNIFORM
DASH NO.
100-1-OR
200-1-OR
300-1-OR
400-1-OR
500-1-OR
1/16
1/8
3/16
1/4
5/16
5/16-24
5/16-24
3/8-24
7/16-20
1/2-20
1.06
1.29
1.35
1.51
1.61
.43
.60
.64
.70
.73
.91
1.03
1.09
1.22
1.31
.34
.34
.38
.41
.44
.55
.55
.62
.74
.86
9/16
9/16
5/8
3/4
7/8
2-011
2-011
2-012
2-111
2-112
6M2SC6
8M2SC8
10M2SC10
12M2SC12
600-1-OR
810-1-OR
1010-1-OR
1210-1-OR
3/8
1/2
5/8
3/4
9/16-18
3/4-16
7/8-14
1-1/16-12
1.67
1.81
1.90
2.06
.76
.87
.87
.87
1.38
1.41
1.50
1.66
.44
.47
.47
.56
.93
1.12
1.30
1.49
15/16
1-1/8
1-3/8
1-1/2
2-113
2-116
2-212
2-215
14M2SC12
16M2SC16
1410-1-OR
1610-1-OR
7/8
1
1-1/16-12
1-5/16-12
2.06
2.30
.87
1.05
1.66
1.81
.56
.56
1.49
1.74
1-1/2
1-3/4
2-215
2-219
A-LOK
PART NO.
INTERCHANGES
WITH
1-2 ZHBA5
2-2 ZHBA5
3-3 ZHBA5
4-4 ZHBA5
5-5 ZHBA5
1M2SC2
2M2SC2
3M2SC3
4M2SC4
5M2SC5
6-6 ZHBA5
8-8 ZHBA5
10-10 ZHBA5
12-12 ZHBA5
14-12 ZHBA5
16-16 ZHBA5
CPI
PART NO.

A
D
ZHBF5, M3SC
Male Connector to
O Ring Pipe Thread
For fractional tube

W HEX
INCHES
PIPE
THREAD
TUBE
O.D.
NPT
PIPE
THREAD
X DIA.
W
HEX
O-RING
ARP
UNIFORM
DASH NO.
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
1-2 ZHBF5
2-2 ZHBF5
2-4 ZHBF5
3-2 ZHBF5
3-4 ZHBF5
1M3SC2
2M3SC2
2M3SC4
3M3SC2
3M3SC4
100-1-2-OR
200-1-2-OR
200-1-4-OR
300-1-2-OR
300-1-4-OR
1/16
1/8
1/8
3/16
3/16
1/8
1/8
1/4
1/8
1/4
1.12
1.29
1.43
1.32
1.46
.43
.60
.60
.64
.64
.97
1.03
1.17
1.06
1.20
.28
.28
.38
.28
.38
.74
.74
.93
.74
.93
3/4
3/4
15/16
3/4
15/16
2-011
2-011
2-113
2-011
2-113
4-2 ZHBF5
4-4 ZHBF5
4-6 ZHBF5
5-2 ZHBF5
5-4 ZHBF5
4M3SC2
4M3SC4
4M3SC6
5M3SC2
5M3SC4
400-1-2-OR
400-1-4-OR
400-1-6-OR
500-1-2-OR
500-1-4-OR
1/4
1/4
1/4
5/16
5/16
1/8
1/4
3/8
1/8
1/4
1.38
1.51
1.57
1.43
1.46
.70
.70
.70
.73
.73
1.09
1.22
1.28
1.13
1.25
.28
.38
.41
.28
.38
.74
.93
1.12
.74
.93
3/4
15/16
1-1/8
3/4
15/16
2-011
2-113
2-116
2-011
2-113
6-2 ZHBF5
6-4 ZHBF5
6-6 ZHBF5
6-8 ZHBF5
8-4 ZHBF5
6M3SC2
6M3SC4
6M3SC6
6M3SC8
8M3SC4
600-1-2-OR
600-1-4-OR
600-1-6-OR
600-1-8-OR
810-1-4-OR
3/8
3/8
3/8
3/8
1/2
1/8
1/4
3/8
1/2
1/4
1.45
1.57
1.63
1.85
1.68
.76
.76
.76
.76
.87
1.16
1.28
1.34
1.56
1.28
.28
.38
.41
.53
.38
.74
.93
1.12
1.30
.93
3/4
15/16
1-1/8
1-3/8
15/16
2-011
2-113
2-116
2-212
2-113
8-6 ZHBF5
8-8 ZHBF5
10-8 ZHBF5
10-12 ZHBF5
12-8 ZHBF5
8M3SC6
8M3SC8
10M3SC8
10M3SC12
12M3SC8
810-1-6-OR
810-1-8-OR
1010-1-8-OR
1010-1-8-OR
1210-1-8-OR
1/2
1/2
5/8
5/8
3/4
3/8
1/2
1/2
3/4
1/2
1.76
1.98
1.96
2.06
1.98
.87
.87
.87
.87
.87
1.36
1.58
1.56
1.66
1.58
.41
.53
.53
.56
.53
1.12
1.30
1.30
1.49
1.30
1-1/8
1-3/8
1-3/8
1-1/2
1-3/8
2-116
2-212
2-212
2-215
2-212
12-12 ZHBF5
16-12 ZHBF5
16-16 ZHBF5
12M3SC12
16M3SC12
16M3SC16
1210-1-12-OR
1610-1-12-OR
1610-1-16-OR
3/4
1
1
3/4
3/4
1
2.06
2.24
2.40
.87
1.05
1.05
1.66
1.75
1.91
.56
.56
.66
1.49
1.49
1.74
1-1/2
1-1/2
1-3/4
2-215
2-215
2-219

54
Tube to O Ring Seal

A
T2HOA5, M2TU
Tube End to O Ring

Straight Thread
For fractional tube

W HEX
INCHES
STRAIGHT
THREAD
T
TUBE
O.D.
STRAIGHT
THREAD
SIZE
X
DIA.
W
HEX
O-RING
ARP
UNIFORM
DASH NO.
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
2-2 T2HOA5
3-3 T2HOA5
4-4 T2HOA5
5-5 T2HOA5
2M2TU2
3M2TU3
4M2TU4
5M2TU5
2-TA-OR-ST
3-TA-OR-ST
4-TA-OR-ST
5-TA-OR-ST
1/8
3/16
1/4
5/16
5/16-24
3/8-24
7/16-20
1/2-20
1.22
1.38
1.55
1.64
.53
.56
.63
.66
.34
.38
.41
.44
.55
.62
.74
.86
9/16
5/8
3/4
7/8
2-011
2-012
2-111
2-112
6-6 T2HOA5
8-8 T2HOA5
10-10 T2HOA5
12-12 T2HOA5
6M2TU6
8M2TU8
10M2TU10
12M2TU12
6-TA-OR-ST
8-TA-OR-ST
10-TA-OR-ST
12-TA-OR-ST
3/8
1/2
5/8
3/4
9/16-18
3/4-16
7/8-14
1-1/16-12
1.70
1.95
2.12
2.16
.69
.91
.97
.97
.47
.47
.47
.56
.93
1.12
1.30
1.49
15/16
1-1/8
1-3/8
1-1/2
2-113
2-116
2-212
2-215
16-16 T2HOA5
16M2TU16
16-TA-OR-ST
1-5/16-12
2.47
1.22
.56
1.74
1-3/4
2-219
T2HOF5, M3TU
Tube End to O Ring

Pipe Thread
For fractional tube
W HEX
INCHES
PIPE
THREAD
X
DIA.
W
HEX
O-RING
ARP
UNIFORM
DASH NO.
.28
.74
3/4
2-111
.63
.63
.63
.66
.66
.28
.38
.41
.28
.38
.74
.93
1.12
.74
.93
3/4
15/16
1-1/8
3/4
15/16
2-111
2-113
2-116
2-111
2-113
1.38
1.50
1.59
1.78
2.14
.69
.69
.69
.91
.97
.28
.38
.41
.41
.53
.74
.93
1.12
1.12
1.30
3/4
15/16
1-1/8
1-1/8
1-3/8
2-111
2-113
2-116
2-116
2-212
2.16
2.56
.97
1.22
.56
.66
1.49
1.65
1-1/2
1-3/4
2-215
2-219
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
T
TUBE
O.D.
NPT
PIPE
THREAD
1-2 T2HOF5
1M3TU2
1-TA-1-20R
1/16
1/8
1.03
.34
4-2 T2HOF5
4-4 T2HOF5
4-6 T2HOF5
5-2 T2HOF5
5-4 T2HOF5
4M3TU2
4M3TU4
4M3TU6
5M3TU2
5M3TU4
4-TA-1-2OR
4-TA-1-4OR
4-TA-1-6OR
5-TA-1-2OR
5-TA-1-4OR
1/4
1/4
1/4
5/16
5/16
1/8
1/4
3/8
1/8
1/4
1.31
1.44
1.50
1.34
1.47
6-2 T2HOF5
6-4 T2HOF5
6-6 T2HOF5
8-6 T2HOF5
10-8 T2HOF5
6M3TU2
6M3TU4
6M3TU6
8M3TU6
10M3TU8
6-TA-1-2OR
6-TA-1-4OR
6-TA-1-6OR
8-TA-1-6OR
10-TA-1-8OR
3/8
3/8
3/8
1/2
5/8
1/8
1/4
3/8
3/8
1/2
12-12 T2HOF5
16-16 T2HOF5
12M3TU12 12-TA-1-12OR
16M3TU16 16-TA-1-16OR
3/4
1
3/4
1
55
Tube to O Ring Seal

FHOA, FHOA
INCHES
Pipe Thread to
SAE Straight
Thread
Adapter
CPI
PART NO.
A-LOK
PART NO.
4-4 FHOA
4-4 FHOA
6-6 FHOA
6-6 FHOA
8-8 FHOA
8-8 FHOA
12-12 FHOA 12-12 FHOA
16-16 FHOA 16-16 FHOA
For fractional
tube
INTERCHANGES
WITH
T2
STRAIGHT
THREAD
NPT T1
PIPE
THREAD
4SAE-1-4
1/4-18
7/16-20
6-SAE-1-6
3/8-18
9/16-18
8-SAE-1-8
1/2-14
3/4- 16
12-SAE-1-12 3/4-14 1-1/16-12
16-SAE-1-16 1-11-1/2 1-5/16-12
R1
R2
W
HEX
O-RING
AS
UNIFORM
DASH NO.
1.20
1.26
1.53
1.75
2.00
.56
.56
.75
.75
.94
.36
.39
.44
.59
.59
9/16
11/16
7/8
1-1/4
1-1/2
3-904
3-906
3-908
3-912
3-916

A
R1
R2
O RING
T1 PIPE
THREAD
T2 STRAIGHT
THREAD
W HEX
AH2BZ, AH2LZ
Bulkhead to
Conversion Adapter
For fractional tube

O RING
D
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
4-6 AH2BZ
6-6 AH2BZ
4-6 AH2LZ
6-6 AH2LZ
400-61-6ST
600-61-6ST
TUBE
O.D.
STRAIGHT
THREAD
SIZE
W
HEX
1/4
3/8
9/16-18
9/16-18
1.74
1.81
1.17
1.24
1.45
1.52
.39
.39
.88
.94
3/4
3/4

BULKHEAD
MAX.
HOLD DRILL BULKHEAD
SIZE
THICKNESS
37/64
37/64
9/16
9/16
56
Tube to Welded Systems

General
Welding Methods
300 Series Stainless Steels
The weld used in joining a tube to a socket weld tube fitting is

like any other type of tee weld. The root (i.e., the point of
intersection of the outside of the tube and annular end area of
the fitting) must be included in the weld zone.
May be welded by the TIG, MIG, or stick arc-weld process.

TIG welding is recommended as being best for welding
Weld-lok systems because it allows better operator control of
heat penetration and filler material deposition.
Careful welding procedures are normally followed to assure

that this root area is included in the weld. If penetration is not
achieved, the joint will have two built-in stress risers which
may greatly reduce the strength of the weld. Upon application
of an extreme load, these stress risers could result in cracks
which could propagate out through the weld or tube depending upon the direction of the greatest load.
Stick arc welding is not recommended in many cases

because of the likelihood of excessive burn-through and
improper root penetration. In all cases where stick welding is
used, it is recommended that backing gas be used.
MIG welding gives the same characteristics as stick electrode
welding with faster deposition of the filler material. As this
process runs hotter than the stick process, the use of a
backing gas is mandatory. It should be noted that in welding
the relatively small fitting sizes found in the Weld-lok line, filler
deposition rate economies are not a factor and therefore the
MIG method is not commonly applied.
Often to achieve full root penetration in TIG welding of stainless steels, a fusion pass will be made first, followed by a final
pass utilizing a filler rod to achieve the desired fillet size.
Assembly
The codes applicable to the welding of socket weld fittings
require that the tube be inserted into the socket until bottomed against the stop. The tube is then to be backed out
approximately 1/16 of an inch and then welded.
C1018 Steel Fittings
If the tube is not backed out, but welded when against a flat
bottom stop, the contraction of the weld fillet and fitting socket
can combine to produce a static stress on the weld. During
thermal transients, the fitting and the portion of the tube within
the fitting may experience a differential rate of heating or cooling, again adding to the stress level in the weld.
Carbide Precipitation
May be welded by the TIG, MIG, stick and oxyacetylene

methods. As scale formation remains a problem, the use of a
backing gas is still recommended.
When unstabilized stainless steels are heated to 8001500F

during welding, the chromium in the steel combines with the
carbon to form chrome carbides which tend to form along the
grain boundaries of the metal (carbide precipitation). This
lowers the dissolved chromium content in these areas and
thus lowers their corrosion resistance, making them vulnerable to intergranular corrosion. Carbide precipitation is
reduced by holding the carbon content of the material to a
very low value. This limits the amount of carbon available to
combine with the chromium. The L series (extra low carbon)
stainless steels are often used for this purpose, but their use
reduces system design stress by approximately 15%. Parker
Weld-lok fittings are made from a select 316 series with carbon content in the low range of 0.04 to 0.07 percent. This
results in a welded fitting with good corrosion resistance and
a high strength factor.
Tacking
If the weld joint is to be tacked before welding, it is recommended that the Tack weld build-up be held to a minimum.
Excessive build-up on the tack may cause an interrupted
final bead and a stress riser or lack of complete fusion.
Backing Gas
Backing gas is an inert gas used to flood the interior of the
fittings and tube system during welding. It serves the same
purpose internally as the shielding gas used in TIG or MIG
welding. By reducing the interior oxygen level to as low as
practicable, it also serves to control the combustion of contaminates that could affect weld quality.
All Parker Weld-lok fittings in stainless steel are supplied

in the solution treated condition, capable of passing
ASTM-A-262 Tests for Detecting Susceptibility to
Intergranular Corrosion.
When a backing gas is not used and nearly 100% weld penetration is achieved, blisters will tend to form on the internal
tube wall. This will result in scale which may later break loose.
Therefore, in 0.050 wall or thinner tube or where the wall
thickness is such that the selected weld process may burn
through, the use of a backing gas is mandatory.
Arc Polarity
When welding Weld-lok fittings, best results will be obtained
by the following arc polarities:
In most cases the backing gas will be argon or helium connected to the system through a control regulator. Flow rates,
while small, should be high enough to purge the system.
Welds should be made in downstream sequence from the
gas connection.
TIG Direct Current, straight polarity

MIG Direct Current, reverse polarity
STICK Polarity dependent on rod used
For further information on Parkers Welded Fittings refer to
Parkers Welded Fittings Catalog 4280 or contact Parkers
Instrumentation Products Division Product Engineering at
256-881-2040.
Note that the entire system should be purged to insure that

there are no openings that will allow air to be drawn into the
system.
The use of backing gas, while often not mandatory, will give
a better weld joint. This is because the effects of contaminate
combustion by-products are eliminated and because the
welds are made and cooled under a shielded atmosphere,
thus eliminating internal scaling or blistering.
57

ZEBW, ZELW
Socket Weld
Elbow
For fractional tube
for CPI/A-LOK to tubing
socket weld connection
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
W
HEX
2-2 ZEBW
3-3 ZEBW
4-4 ZEBW
6-6 ZEBW
8-8 ZEBW
2-2 ZELW
3-3 ZELW
4-4 ZELW
6-6 ZELW
8-8 ZELW
200-9-2 W
300-9-3 W
400-9-4 W
600-9-6 W
810-9-8 W
1/8
3/16
1/4
3/8
1/2
.92
.98
1.07
1.26
1.37
.66
.72
.78
.97
.97
.63
.69
.78
.91
1.03
.16
.20
.25
.34
.41
.38
.44
.50
.63
.76
5/16
7/16
9/16
3/4
3/4
5/8
3/4
1
1.56
1.56
1.94
1.16
1.16
1.45
1.16
1.31
1.47
.49
.50
.56
.94
1.09
1.38
1-1/16
1-1/16
1-5/16
10-10 ZEBW 10-10 ZELW 1010-9-10 W

12-12 ZEBW 12-12 ZELW 1210-9-12 W
16-16 ZEBW 16-16 ZELW 1610-9-16 W
*Socket Depth
C
L
W HEX
*P
X
ZEBW2, ZELW2
L
W HEX
Buttweld Elbow
For fractional pipe
for CPI/A-LOK to pipe buttweld
connection
H
R
X
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
BUTTWELD
PIPE
SIZE
2-1/8 ZEBW2
3-1/8 ZEBW2
4-1/8 ZEBW2
4-1/4 ZEBW2
6-1/4 ZEBW2
2-1/8 ZELW2
3-1/8 ZELW2
4-1/8 ZELW2
4-1/4 ZELW2
6-1/4 ZELW2
200-2-2 W
300-2-2 W
400-2-2 W
400-2-4 W
600-2-4 W
1/8
3/16
1/4
1/4
3/8
1/8
1/8
1/8
1/4
1/4
.92
1.01
1.06
1.07
1.20
.72
.74
.74
.94
1.01
8-3/8 ZEBW2
8-1/2 ZEBW2
10-1/2 ZEBW2
12-3/4 ZEBW2
16-3/4 ZEBW2
8-3/8 ZELW2
810-2-6 W
8-1/2 ZELW2 810-2-8 W
10-1/2 ZELW2 1010-2-8 W
12-3/4 ZELW2 1210-2-12 W
16-3/4 ZELW2 1610-2-12 W
1/2
1/2
5/8
3/4
1
3/8
1/2
1/2
3/4
3/4
1.37
1.43
1.43
1.56
1.94
1.94
16-1 ZEBW2
16-1 ZELW2
1610-2-16 W

Pipe buttweld end will conform to Schedule 80 unless otherwise noted.
X
BUTTWELD
O.D.
W
HEX
.66
.74
.77
.78
.91
.34
.38
.38
.56
.56
.405
.405
.405
.540
.540
7/16
1/2
1/2
9/16
5/8
1.13
1.31
1.31
1.50
1.65
.97
1.03
1.03
1.16
1.45
.56
.75
.75
.75
.75
.675
.840
.840
1.050
1.050
3/4
7/8
7/8
1-1/16
1-3/8
1.84
1.45
.94
1.315
1-3/8
58

A
ZHBW, ZHLW
Socket Weld Connector

For fractional tube
E X
for CPI/A-LOK to tubing socket weld

connection
W HEX
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
2-2 ZHBW
3-3 ZHBW
4-4 ZHBW
6-6 ZHBW
2-2 ZHLW
3-3 ZHLW
4-4 ZHLW
6-6 ZHLW
200-6-2 W
300-6-3 W
400-6-4 W
600-6-6 W
1/8
3/16
1/4
3/8
8-8 ZHBW
10-10 ZHBW
12-12 ZHBW
16-16 ZHBW
8-8 ZHLW
10-10 ZHLW
12-12 ZHLW
16-16 ZHLW
810-6-8 W
1010-6-10 W
1210-6-12 W
1610-6-16 W
1/2
5/8
3/4
1
E
BORE
W
HEX
.38
.42
.48
.61
.093
.125
.187
.281
7/16
7/16
1/2
5/8
.79
.92
1.11
1.36
.406
.500
.625
.875
13/16
15/16
1-1/8
1-3/8
1.14
1.17
1.32
1.48
.60
.64
.70
.76
.88
.91
1.03
1.19
.16
.20
.25
.34
1.62
1.65
1.71
2.08
.87
.87
.87
1.05
1.22
1.25
1.31
1.59
.41
.47
.50
.56

Socket Depth
ZHBW2, ZHLW2
D
R
Buttweld Connector
For fractional pipe
for CPI/A-LOK to pipe buttweld

connection
W HEX
INCHES
TUBE
O.D.
BUTTWELD
PIPE
SIZE
X
BUTTWELD
O.D.
W
HEX
.94
.97
1.00
1.20
1.22
.38
.38
.38
.56
.38
.405
.405
.405
.540
.405
7/16
7/16
1/2
9/16
1/2
.73
.76
.76
.76
.76
1.23
1.28
1.31
1.53
1.59
.56
.56
.56
.75
.75
.540
.540
.675
.840
1.050
9/16
5/8
3/4
7/8
1-1/8
.87
.87
.87
.87
.87
1.05
1.31
1.53
1.59
1.53
1.59
1.97
.56
.75
.75
.75
.75
.94
.675
.840
1.050
.840
1.050
1.310
13/16
7/8
1-1/8
15/16
1-1/8
1-3/8
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
ZHBW2 2-1/8
ZHBW2 3-1/8
ZHBW2 4-1/8
ZHBW2 4-1/4
ZHBW2 5-1/8
2-1/8 ZHLW2
3-1/8 ZHLW2
4-1/8 ZHLW2
4-1/4 ZHLW2
5-1/8 ZHLW2
200-1-2 W
300-1-2 W
400-1-2 W
400-1-4 W
500-1-2 W
1/8
3/16
1/4
1/4
5/16
1/8
1/8
1/8
1/4
1/8
1.20
1.24
1.29
1.49
1.48
.60
.64
.70
.70
.73
ZHBW2 5-1/4
ZHBW2 6-1/4
ZHBW2 6-3/8
ZHBW2 6-1/2
ZHBW2 6-3/4
5-1/4-ZHLW2
6-1/4 ZHLW2
6-3/8 ZHLW2
6-1/2 ZHLW2
6-3/4 ZHLW2
500-1-4-W
600-1-4 W
600-1-6 W
600-1-8 W
600-1-12 W
5/16
3/8
3/8
3/8
3/8
1/4
1/4
3/8
1/2
3/4
1.49
1.57
1.60
1.82
1.88
ZHBW2 8-3/8
ZHBW2 8-1/2
ZHBW2 8-3/4
ZHBW2 10-1/2
ZHBW2 12-3/4
ZHBW2 16-1
8-3/8 ZHLW2
810-1-6 W
8-1/2 ZHLW2
810-1-8 W
8-3/4 ZHLW2 810-1-12 W
10-1/2 ZHLW2 1010-1-8 W
12-3/4 ZHLW2 1210-1-12 W
16-1 ZHLW2 1610-1-16 W
1/2
1/2
1/2
5/8
3/4
1
3/8
1/2
3/4
1/2
3/4
1
1.71
1.93
1.99
1.93
1.99
2.46

Pipe Buttweld end will conform to Schedule 80 unless otherwise noted.
59

ZHBW2,
ZHLW2
MILLIMETERS
Buttweld
Connector
For metric pipe
for CPI/A-LOK to pipe
buttweld connection
A
D
R
E X
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
BUTTTUBE WELD
O.D. PIPE N.B.
ZHBW2 3-1/8
ZHBW2 4-1/8
ZHBW2 6-1/8
ZHBW2 6-1/4
ZHBW2 8-1/8
ZHLW2 3-1/8
ZHLW2 4-1/8
ZHLW2 6-1/8
ZHLW2 6-1/4
ZHLW2 8-1/8
3MO-1-2W
4MO-1-2
6MO-1-2
6MO-1-4W
8MO-1-2
3
4
6
6
8
ZHBW2 8-1/4
ZHBW2 8-1/2
ZHBW2 10-1/4
ZHBW2 10-3/8
ZHBW2 10-1/2
ZHLW2 8-1/4
ZHLW2 8-1/2
ZHLW2 10-1/4
ZHLW2 10-3/8
ZHLW2 10-1/2
8MO-1-1/4
8MO-1-8
10MO-1-6
ZHBW2 12-1/4
ZHBW2 12-3/8
ZHBW2 12-1/2
ZHBW2 15-1/2
ZHBW2 16-1/2
ZHBW2 18-1/2
ZHLW2 12-1/4
ZHLW2 12-3/8
ZHLW2 12-1/2 12MO-1-8W

ZHLW2 15-1/2
ZHLW2 16-1/2
ZHLW2 18-1/2
E
BORE
W
HEX
1/8
1/8
1/8
1/4
1/8
29,7
30,7
32,9
37,7
34,2
15,3
16,1
17,7
17,7
18,6
23,1
24,1
25,4
30,2
26,7
9,7
9,7
9,7
14,2
9,7
10,3
10,3
10,3
13,7
10,3
2,4*
2,4*
4,8
4,8*
5,1
12,0
12,0
14,0
14,0
15,0
8
8
10
10
10
1/4
1/2
1/4
3/8
1/2
38,7
44,8
40,9
40,1
45,7
18,6
18,6
19,5
19,5
19,5
31,2
37,3
33,3
32,5
38,1
14,2
19,1
14,2
14,2
19,1
13,7
21,3
13,7
17,2
21,3
6,4
6,4*
7,1
7,9*
7,9*
15,0
22,0
18,0
18,0
22,0
12
12
12
1/4
3/8
1/2
1/2
1/2
1/2
43,4
43,4
48,2
48,2
49,0
50,5
22,0
22,0
22,0
22,0
22,0
22,0
33,3
33,3
38,1
38,9
38,9
40,4
14,2
14,2
19,1
19,1
19,1
19,1
13,7
17,2
21,3
21,3
21,3
21,3
7,1
9,5
9,5*
9.5*
12,7*
13,5
22,0
22,0
22,0
24,0
24,0
27,0
16
18
NOTE: *E dimension is minimum opening.

Fittings of this group may be back-drilled to larger I.D. at pipe end.
A and C dimensions are typical finger-tight.
Pipe Buttweld end will conform to Schedule 80 unless otherwise noted.
W HEX
60
Analytical Fittings
Conical angle allows
dispersement of flow
over more frit surface
.03
Controlled
internal
volume
6.1 X 104 cc
FLOW
.060
90
.020 I.D.
Drop In Frit Design
Frit contained in tube bore

by tubing with proper
fitting make up.
Precision tolerance
tube bore for
frit alignment.
Drop in frit allows

accessibility for
micron changes and
cleaning
15
Flow stream contacts
entire frit surface
eliminating
unswept volume
.05
Controlled
internal
volume
1.2 X 103 cc
FLOW
.122
.0135 I.D.
Lead in angle for
frit positioning
Press In Frit Design
Precision tolerance
counter bore for
frit assembly
Parker Hannifins Instrumentation Products Division offers a

full line of analytical tube fittings. These fittings range from
elbows, tees, and male connectors to low dead volume
unions and column end fittings. Parker incorporates various
features in the column end fittings to effectively address various industry concerns.
Avoidance of entrapment
areas by flush mounting
frit in counterbore
Pressed in frit eliminates

movement of frit under
pressure or disassembly.
incorporated a small conical angle on the fitting body internals. This conical angle helps to equally disperse the sample
into the column tube. One of the key requirements of an effective column end fitting is not to delay or disturb the flow of the
sample through the instrument (HPLC column).
A second area to address is the minimizing of tube fitting
internal cavities. A cavity is a short section of the flow path
where the flow-channel diameter increases. It can occur
where tubes are connected to each other (low dead volume
connector) or to injectors, columns (column end fittings), and
detectors. Large cavities can seriously degrade the resolution
of any chromatogram, but they can be easily avoided through
awareness of the geometric design details of the fittings and
connecting parts manufactured by various companies.
Peak symmetry for critical analysis

Internal volume reduction
As the observed media/substance migrates through the
HPLC column, a peak or band is created that denotes the
level of concentration. It is critical to maintain peak symmetry
in order to get an accurate reading when processing the
observed media/substance. Parker Hannifin, in the development of a line of column end fittings, has incorporated some
key features that help to maintain this peak symmetry in
HPLC columns.
Parker Hannifin has incorporated those critical features in both

a low dead volume union connector and the column end fitting
bodies. First, the utilization of inverted 1/16" connections to
greatly reduce internal volume or cavities.To eliminate any
confusion or occurrence of incorrect effective tube make-up,
the port depths (body bore dimensions) are identical by size
throughout the entire Parker Hannifin instrumentation line.
Second, Parker closely monitors the dimensions of the small
through-hole utilized in these low dead volume connectors.
Under most circumstances in liquid chromatography (LC),

the flow through the tube is laminar, the so-called Poiseulle
flow, and in this situation the velocity at all points is parallel to
the tube axis.
Due to the importance of maintaining smooth laminar flow
after injection of the sample into the HPLC column, Parker
61
Analytical Fittings
Z2HCZ7,
Z2HLZ7
INCHES
Column End
Fitting Low
Internal Volume
with Frit
For fractional tube
CPI
PART NO.
A-LOK
PART NO.
T1
TUBE
O.D.
T2
TUBE
O.D.
W
HEX
INTERNAL
OPENING
INTERNAL
VOLUME
2-1 Z2HCZ7
2-1 Z2HLZ7
1/8
1/16
1.25
.60
.78
7/16
.013
5.4 x 10-4cc
4-1 Z2HCZ7
4-1 Z2HLZ7
1/4
1/16
1.35
.70
.84
1/2
.013
1.2 x 10-3cc
6-1 Z2HCZ7
6-1 Z2HLZ7
3/8
1/16
1.43
.76
.92
5/8
.013
3.8 x 10-3cc
HOW TO ORDER
FRIT DESIGNATOR
* MICRON DASH NO.
1
2
3
4
A
C2
MICRON SIZE
C1
T2
T1
EXAMPLE: 4-1Z2HLZ7-2*-SS
To order with 2
frit for 1/4"
O.D. column
0.5
2
5
10
Features:
Inverted 1/16" end substantially reduces internal volume
Flow stream contacts entire frit surface reducing plugging and
eliminating unswept volume
Can be used as a low volume final filter
W HEX
D
Z3HCZ7, Z3HLZ7
Column End Fitting
Low Internal Volume
For fractional tube
INCHES
T1
TUBE
O.D.
T2
TUBE
O.D.
W
HEX
INTERNAL
OPENING
INTERNAL
VOLUME
4-1 Z3HCZ7 4-1 Z3HLZ7
1/4
1/16
1.28
.70
.77
1/2
.020
6.1 x 10-4cc
6-1 Z3HCZ7
6-1 Z3HLZ7
3/8
1/16
1.37
.76
.86
5/8
.020
8.1 x 10-4cc
8-1 Z3HCZ7
8-1 Z3HLZ7
1/2
1/16
1.62
.87
1.00
13/16
.030
2.8 x 10-3cc
1/16
2.00
1.05
1.31
1-3/8
.030
2 x 10-2cc
CPI
PART NO.
A-LOK
PART NO.
16-1 Z3HCZ7 16-1 Z3HLZ7

A
C
T2
T1
W HEX
D
Di-Frit (drop in)
Replaceable frit for preparatory column

end fitting Z3HLZ7. Frits are available in
2, 5 and 10 micron sizes.
Features:
Inverted 1/16" end substantially reduces internal volume
Drop in frit for use with L.C.* columns or G.C.* columns
Conical angle below frit directs flow over more frit surface
Available for up to 1" columns
*G.C. = Gas Chromatagraph
L.C. = Liquid Chromatagraph
CPI/A-LOK
PARKER PART NO.
MICRON
SIZE
COLUMN
O.D.
4DI FRIT-2MIC-SS
1/4"
4DI FRIT-5MIC-SS
1/4"
4DI FRIT-10MIC-SS
10
6DI FRIT-2MIC-SS
MICRON
SIZE
COLUMN
O.D.
8DI FRIT-2MIC-SS
1/2"
8DI FRIT-5MIC-SS
1/2"
1/4"
8DI FRIT-10MIC-SS
10
1/2"
3/8"
16DI FRIT-2MIC-SS
1"
6DI FRIT-5MIC-SS
3/8"
16DI FRIT-5MIC-SS
1"
6DI FRIT-10MIC-SS
10
3/8"
16DI FRIT-10MIC-SS
10
1"
PARKER PART NO.
62
Analytical Fittings
ZHCZ7, ZHLZ7
Column End
Fitting Low
Internal Volume
(without Frit)
For fractional tube
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
T1
TUBE
O.D.
T2
TUBE
O.D.
W
HEX
INTERNAL
OPENING
INTERNAL
VOLUME
2-1 ZHCZ7
2-1 ZHLZ7
-200-6-1-FGC
1/8
1/16
1.16
.60
.70
7/16
.013
1.0 x 10-4cc
4-1 ZHCZ7
4-1 ZHLZ7
-400-6-1-FGC
1/4
1/16
1.24
.70
.77
1/2
.013
1.1 x 10-4cc
6-1 ZHCZ7
6-1 ZHLZ7
-600-6-1-FGC
3/8
1/16
1.35
.76
.86
5/8
.013
1.3 x 10-4cc
Features:
Inverted 1/16" end substantially
No frit for use with G.C.* columns or L.C.* columns with screens
Can be used as a low volume reducing union
A
C
T2
*G.C. = Gas Chromatagraph

L.C. = Liquid Chromatagraph
T1
W HEX
D
Z2HCZ, Z2HLZ
A
C2
Column End Fitting

with Frit
C1
T1
T2
For fractional tube

W HEX
D
INCHES
CPI
PART NO.
A-LOK
PART NO.
T1
TUBE
O.D.
2-1 Z2HCZ
2-1 Z2HLZ
1/8
1/16
1.21
.60
.43
.81
7/16
.020
2.1 x 10-3cc
4-1 Z2HCZ
4-1 Z2HLZ
1/4
1/16
1.35
.70
.43
.91
1/2
.020
1.8 x 10-3cc
6-1 Z2HCZ
6-1 Z2HLZ
3/8
1/16
1.44
.76
.43
1.00
5/8
.020
5.4 x 10-3cc
T2
TUBE
O.D.
C1
C2
W
HEX
INTERNAL
OPENING
INTERNAL
VOLUME
HOW TO ORDER
FRIT DESIGNATOR
* MICRON DASH NO.
1
2
3
4
MICRON SIZE
0.5
2
5
10
EXAMPLE: 4-1Z2HLZ-2*-SS
To order with 2
frit for 1/4"
O.D. column
NOTE: Size 1 not silver-plated.
Features:
Flow stream contacts entire frit surface reducing
plugging and eliminating unswept volume
Can be used as a low volume final filter with drop-in frit
63
Analytical Fittings
A
ZHCZ, ZHLZ
C2
Column End Fitting

(without Frit)
C1
T2
T1
For fractional tube
W HEX
D
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
T1
TUBE
O.D.
T2
TUBE
O.D.
C1
C2
W
HEX
INTERNAL
OPENING
INTERNAL
VOLUME
2-1 ZHCZ
2-1 ZHLZ
200-6-1LV
1/8
1/16
1.21
.60
.43
.81
7/16
.020
2.1 x 10-3cc
4-1 ZHCZ
4-1 ZHLZ
400-6-1LV
1/4
1/16
1.35
.70
.43
.91
1/2
.020
2.1 x 10-3cc
6-1 ZHCZ
6-1 ZHLZ
600-6-1LV
3/8
1/16
1.44
.76
.43
1.00
5/8
.020
2.3 x 10-3cc

Size 1 Nut is not silver plated
Z7HBZ7-SS, Z7HLZ7
Union Connector
Low Dead Volume
H
D1
D2
T2
T1
For fractional tube
G1
G2
W HEX
INCHES
INTERCHANGES
WITH
T1
TUBE
O.D.
T2
TUBE
O.D.
D1
1-1 Z7HBZ7-SS 1-1 Z7HLZ7 IFO-6GC
1/16
1/16
1.26
.21
.21
2-1 Z7HBZ7-SS 2-1 Z7HLZ7
1/8
1/16
1.53
.31
2-2 Z7HBZ7-SS 2-2 Z7HLZ7
1/8
1/8
1.81
.31
CPI
PART NO.
A-LOK
PART NO.
D2
E
INTERNAL
OPENING
G1
G2
W
HEX
INTERNAL
VOLUME
.41
.41
.013
.25
.25
.84
1/4
8.7 x 10-5cc
.21
.56
.41
.013
.38
.25
1.02
7/16
8.7 x 10-5cc
.31
.56
.56
.052
.38
.38
1.19
7/16
9.7 x 10-2cc
Average Value
64
Analytical Fittings
FBZ7, FLZ7
A
R
Male Connector
Low Dead Volume
For fractional tube
W HEX
B
INCHES
CPI
PART NO.
A-LOK
PART NO.
NPT
TUBE
O.D.
1-1 FBZ7
1-1 FLZ7
1/16
1/16
.75
.55
.38
5/16
.013
3.1 x 10-4cc
1-2 FBZ7
1-2 FLZ7
1/16
1/8
.79
.59
.38
7/16
.013
4.4 x 10-4cc
1-4 FBZ7
1-4 FLZ7
1/16
1/4
1.01
.81
.56
5/8
.013
8.8 x 10-4cc
PIPE
THREAD
W
HEX
INTERNAL
OPENING
INTERNAL
VOLUME
Average Value
ZHBS, ZHLS
Sanitary Flange
Fitting
B I
D
C
For fractional tube
F
B I
D
C
A
INCHES
CPI
PART NO.
PARKER
PART NO.
INTERCHANGES
WITH
TUBE
OD
SANITARY
FLANGE
4-8 ZHBS
4-12 ZHBS
4-16 ZHBS
4-24 ZHBS
6-8 ZHBS
6-12 ZHBS
6-16 ZHBS
6-24 ZHBS
8-8 ZHBS
8-12 ZHBS
8-16 ZHBS
8-24 ZHBS
4-8 ZHLS-SS
4-12 ZHLS-SS
4-16 ZHLS-SS
4-24 ZHLS-SS
6-8 ZHLS-SS
6-12 ZHLS-SS
6-16 ZHLS-SS
6-24 ZHLS-SS
8-8 ZHLS-SS
8-12 ZHLS-SS
8-16 ZHLS-SS
8-24 ZHLS-SS
SS-400-SC-8
SS-400-SC-12
SS-400-SC-16
SS-400-SC-24
SS-600-SC-8
SS-600-SC-12
SS-600-SC-16
SS-600-SC-24
SS-810-SC-8
SS-810-SC12
SS-810-SC-16
SS-810-SC-24
1/4
1/4
1/4
1/4
3/8
3/8
3/8
3/8
1/2
1/2
1/2
1/2
1/2
3/4
1
1 1/2
1/2
3/4
1
1 1/2
1/2
3/4
1
1 1/2
1.57
1.57
1.57
1.57
1.63
1.63
1.63
1.63
1.74
1.74
1.74
1.74
.37
.62
.87
1.37
.37
.62
.87
1.37
.37
.62
.87
1.37
.70
.70
.70
.70
.76
.76
.76
.76
.90
.90
.90
.90
NOTE: A, C, and D dimensions are typical finger tight.
E
MIN.
OPENING
.60
.60
.60
.60
.66
.66
.66
.66
.86
.86
.86
.86
.19
.19
.19
.19
.28
.28
.28
.28
.37
.41
.41
.41
G
HEX
FLAT
1.00
1.00
1.38
1.38
1.00
1.00
1.38
1.38
1.00
1.00
1.38
1.38
9/16
9/16
9/16
9/16
11/16
11/16
11/16
11/16
7/8
7/8
7/8
7/8
1.34
1.34
1.34
1.28
1.34
1.34
1.34
1.34
1.40
1.34
1.34
1.34
.98
.98
1.98
1.98
.98
.98
1.98
1.98
.98
.98
1.98
1.98
Sanitary flange fittings combine the reliability and versatility of Parker tube fittings with conventional sanitary flanges. The fittings permit direct downstream connections for hookups and sampling.
Flange sizes are 1/2, 3/4, 1, and 1-1/2 in.
Parker tube fitting ends are available in 1/4, 3/8, and 1/2 in. Parker tube fittings allow use of a variety of tubing materials including metal, hard plastic, and soft
plastic.
For a Thermocouple/Bored-Thru version of the above Sanitary Adapter fittings, add a 4 to the part number. Example: A 4-12 ZHLS-SS becomes a
4-12 ZH4LS-SS for a 3/4" Sanitary Flange with a 1/4" diameter bored through on the A-LOK fitting end.
65
Barbed Fittings
B2HF, B2HF
INCHES
Barbed
Connector to
Male Pipe
For fractional tube
A
K
T1
HOSE
I.D.
T2 MALE
PIPE
SIZE
E
BORE
W
HEX
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
2-2 B2HF
2-4 B2HF
4-2 B2HF
4-4 B2HF
2-2 B2HF
2-4 B2HF
4-2 B2HF
4-4 B2HF
2-HC-1-2
2-HC-1-4
4-HC-1-2
4-HC-1-4
1/8
1/8
1/4
1/4
1/8
1/4
1/8
1/4
1.00
1.22
1.41
1.59
.078
.078
.188
.188
.41
.41
.75
.78
7/16
9/16
7/16
9/16
5-2 B2HF
5-4 B2HF
6-4 B2HF
6-6 B2HF
5-2 B2HF
5-4 B2HF
6-4 B2HF
6-6 B2HF
5-HC-1-2
5-HC-1-4
6-HC-1-4
6-HC-1-6
5/16
5/16
3/8
3/8
1/8
1/4
1/4
3/8
1.50
1.69
1.72
1.72
.188
.250
.281
.297
.88
.88
.88
.88
7/16
9/16
9/16
11/16
8-6 B2HF
8-8 B2HF
12-12 B2HF
8-6 B2HF
8-8 B2HF
12-12 B2HF
8-HC-1-6
8-HC-1-8
12-HC-1-12
1/2
1/2
3/4
3/8
1/2
3/4
1.81
2.00
2.13
.375
.375
.625
.94
.94
1.03
3/4
7/8
1-1/16

E
T2
T1
W HEX
B2HT2, B2TU
Barbed
Connector to
Tube Adapter
For fractional tube
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
T1
HOSE
I.D.
T2
TUBE
O.D.
E
BORE
W
HEX
2-2 B2HT2
4-4 B2HT2
4-4 B2HT2
6-6 B2HT2
2 B2TU2
4 B2TU4
4 B2TU4
6 B2TU6
2-HC-A-201
2-HC-A-401
4-HC-A-401
4-HC-A-601
1/8
1/8
1/4
1/4
1/8
1/4
1/4
3/8
1.16
1.26
1.64
1.75
.078
.078
.156
.156
.53
.64
.64
.72
.41
.41
.78
.78
5/16
3/8
3/8
7/16

NOTE: Tube adapter end is designed for use with Parker fittings or valves. Simply insert the tube adapter end until it bottoms
and tighten the Parker nut 3/4 turns for sizes 3 and below, for sizes 4 and above 1-1/4 turns from finger tight.
A
K
T2
E
T1
W HEX
HCS, HCS
Hose Connector
Sleeve
For fractional tube
INCHES
CPI
PART NO.
A-LOK
PART NO.
HOSE
I.D.
HOSE
O.D.
W
HEX
2-4 HCS
4-6 HCS
4-7 HCS
4-8 HCS
HCS 2-4
HCS 4-6
HCS 4-7
HCS 4-8
1/8
1/4
1/4
1/4
1/4
3/8
7/16
1/2
.41
.78
.78
.78
3/8
9/16
5/8
11/16
4-9 HCS
5-7 HCS
6-8 HCS
6-9 HCS
HCS 4-9
HCS 5-7
HCS 6-8
HCS 6-9
1/4
5/16
3/8
3/8
9/16
7/16
1/2
9/16
.78
.88
.88
.88
3/4
5/8
11/16
3/4
8-11 HCS
12-16 HCS
HCS 8-11
HCS 12-16
1/2
3/4
11/16
1
.94
1.06
7/8
1-1/4
W HEX
66
Components
TIZ
Insert
For fractional tube
CPI
PART NO.
A-LOK
PART NO.
INCHES
INTERCHANGES
WITH
TUBE
O.D.
TUBE
I.D.
TUBE
WALL
3 TIZ (.125)
4 TIZ (.125)
4 TIZ (.170)
4 TIZ (.188)
5 TIZ (.125)
3 TIZ (.125)
4 TIZ (.125)
4 TIZ (.170)
4 TIZ (.188)
5 TIZ (.125)
305-2
405-2
405-170
405-3
505-2
3/16
1/4
1/4
1/4
5/16
.125
.125
.170
.188
.125
.031
.062
.040
.031
.094
5 TIZ (.188)
5 TIZ (.250)
6 TIZ (.188)
6 TIZ (.250)
8 TIZ (.250)
5 TIZ (.188)
5 TIZ (.250)
6 TIZ (.188)
6 TIZ (.250)
8 TIZ (.250)
505-3
505-4
605-3
605-4
815-4
5/16
5/16
3/8
3/8
1/2
.188
.250
.188
.250
.250
.062
.031
.094
.062
.125
8 TIZ (.375)
10 TIZ (.375)
10 TIZ (.500)
12 TIZ (.500)
12 TIZ (.625)
8 TIZ (.375)
10 TIZ (.375)
10 TIZ (.500)
12 TIZ (.500)
12 TIZ (.625)
815-6
1015-6
1015-8
1215-8
1215-10
1/2
5/8
5/8
3/4
3/4
.375
.375
.500
.500
.625
.062
.125
.062
.125
.062
16 TIZ (.750)
16 TIZ (.875)
16 TIZ (.750)
16 TIZ (.875)
1615-12
1615-14
1
1
.750
.875
.125
.062

NOTE: The TIZ insert is designed to be used with soft plastic tubing. Tubing wall thickness and corresponding minimum I.D.
flow paths are listed so the system designer can properly match the insert to the tubing.
Example: 4 TIZ (.125) is used with tubing having a wall thickness of .062 and I.D. of .125.
TIZ
Insert
For metric tube
MILLIMETERS
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
TUBE
I.D.
TUBE
WALL
TIZ6(4)
TIZ8(6)
TIZ10(6)
TIZ10(8)
TIZ12(8)
TIZ12(10)
TIZ15(10)
TIZ6(4)
TIZ8(6)
TIZ10(6)
TIZ10(8)
TIZ12(8)
TIZ12(10)
TIZ15(10)
6M5-4M
8M5-6M
10M5-6M
10M5-8M
12M5-8M
12M5-10M
15M5-10M
6
8
10
10
12
12
15
4
6
6
8
8
10
10
1,0
1,0
2,0
1,0
2,0
1,0
2,5

NOTE: The TIZ insert is designed to be used with soft plastic tubing. Tubing wall thickness and corresponding minimum I.D.
flow paths are listed so the system designer can properly match the insert to the tubing.
Example: TIZ6(4) is used with tubing having a wall thickness of 1mm and I.D. of 4mm.
BZ, NU
Tube Nut
For fractional tube
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
W
HEX
1 BZ
2 BZ
3 BZ
4 BZ
5 BZ
1NU1
2NU2
3NU3
4NU4
5NU5
102-1
202-1
302-1
402-1
502-1
1/16
1/8
3/16
1/4
5/16
.31
.47
.47
.50
.53
5/16
7/16
1/2
9/16
5/8
6 BZ
8 BZ
10 BZ
12 BZ
14 BZ
6NU6
8NU8
10NU10
12NU12
14NU14
602-1
812-1
1012-1
1212-1
1412-1
3/8
1/2
5/8
3/4
7/8
.56
.69
.69
.69
.69
11/16
7/8
1
1-1/8
1-1/4
16 BZ
20 BZ
24 BZ
32 BZ
16NU16
20NU20
24NU24
32NU32
1612-1
2012-1
2412-1
3212-1
1
1-1/4
1-1/2
2
.81
1.25
1.50
2.062
1-1/2
1-7/8
2-1/4
3
W HEX

NOTE: All size 20, 24 and 32 silver plated nuts should have a system compatible lube (Permatex Anti-seize Parker Catalog
4290-INST) or equivalent applied to the fitting body threads and the inside back of nuts. This will minimize the effort required
to assemble the
fitting properly.
67
Components
BZ, NUM
Tube Nut
For metric tube
A
W HEX
MILLIMETERS
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
UN
THREAD
TUBE
O.D.
W
HEX
BZ 2
BZ 3
BZ 4
BZ 6
BZ 8
NUM2
NUM3
NUM4
NUM6
NUM8
2M2-1
3M2-1
4M2-1
6M2-1
8M2-1
2
3
4
6
8
5/16-20
5/16-20
3/8-20
7/16-20
1/2-20
11,9
11,9
11,9
12,7
13,5
12,0
12,0
12,0
14,0
16,0
BZ 10
BZ 12
BZ 14
BZ 15
BZ 16
NUM10
NUM12
NUM14
NUM15
NUM16
10M2-1
12M2-1
14M2-1
15M2-1
16M2-1
10
12
14
15
16
5/8-20
3/4-20
7/8-20
7/8-20
7/8-20
15,1
17,5
17,5
17,5
17,5
19,0
22,0
25,0
25,0
25,0
BZ 18
BZ 20
BZ 22
BZ 25
NUM18
NUM20
NUM22
NUM25
18M2-1
20M2-1
22M2-1
25M2-1
18
20
22
25
1-20
1.1/8-20
1.1/8-20
1.5/16-20
17,5
17,5
17,5
20,6
30,0
32,0
32,0
38,0
BZI
Inverted Tube Nut
For fractional tube
INCHES
CPI/
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
W
HEX
1 BZI
2 BZI
1F2-1GC
2F2-1GC
1/16
1/8
.39
.44
1/4
7/16
W HEX
BZP
Knurled Nut
For fractional tube
INCHES
CPI/
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
1 BZP
2 BZP
3 BZP
102-1K
202-1K
302-1K
1/16
1/8
3/16
.32
.47
.47
4 BZP
5 BZP
6 BZP
402-1K
502-1K
812-1K
1/4
5/16
3/8
.51
.54
.57
8 BZP
10 BZP
602-1K
1012-1K
1/2
5/8
.69
.69
HOW TO ASSEMBLE BZP

1. Replace NU nut with BZP nut on Parker
A-LOK fitting body.
2. Insert plastic tubing until it bottoms in fitting
body.
3. Tighten finger tight.
The knurled nut is designed for use with soft
plastic tubing on low pressure applications where
a finger tight assembly procedure is satisfactory.
Example: Laboratory test hook-ups. Nylon or
Teflon ferrules are frequently used instead of
metal ferrules in this type of application.
TZ
Ferrules
PARKER
PART NO.
PARKER
PART NO.
TUBE
O.D. (INCHES)
1 TZ
2 TZ
3 TZ
4 TZ
5 TZ
6 TZ
8 TZ
1/16
1/8
3/16
1/4
5/16
3/8
1/2
10 TZ
12 TZ
14 TZ
16 TZ
20 TZ
24 TZ
32 TZ
5/8
3/4
7/8
1
1-1/4
1-1/2
2
TZ 3
TZ 6
TZ 8
TZ 10
TZ 12
TZ 16
TZ 20
TZ 25
TUBE
O.D. (INCHES)
6
8
10
12
16
Dimensions for reference only,

subject to change.
Dimensions for reference only,
subject to change.
68
Components
INCH
FF
PARKER
PART NO.
INTERCHANGES
WITH
INCHES
TUBE
O.D.
1FF1
2FF2
3FF3
4FF4
5FF5
103-1
203-1
303-1
403-1
503-1
1/16
1/8
3/16
1/4
5/16
6FF6
8FF8
10FF10
12FF12
14FF14
603-1
813-1
1013-1
1213-1
1413-1
3/8
1/2
5/8
3/4
7/8
16FF16
20FF20
24FF24
32FF32
1613-1
2013-1
2413-1
3213-1
1
1-1/4
1-1/2
2
Front Ferrule
PARKER
PART NO.
INTERCHANGES
WITH
MM
TUBE
O.D.
For metric tube
FFM2
FFM3
FFM4
FFM6
FFM8
2M3-1
3M3-1
4M3-1
6M3-1
8M3-1
2
3
4
6
8
FFM10
FFM12
FFM14
FFM15
FFM16
10M3-1
12M3-1
14M3-1
15M3-1
16M3-1
10
12
14
15
16
FFM18
FFM20
FFM22
FFM25
18M3-1
20M3-1
22M3-1
25M3-1
18
20
22
25
Front Ferrule
For fractional tube
BF
INTERCHANGES
WITH
INCHES
TUBE
O.D.
1BF1
2BF2
3BF3
4BF4
5BF5
104-1
204-1
304-1
404-1
504-1
1/16
1/8
3/16
1/4
5/16
6BF6
8BF8
10BF10
12BF12
14BF14
604-1
814-1
1014-1
1214-1
1414-1
3/8
1/2
5/8
3/4
7/8
16BF16
20BF20
24BF24
32BF32
1614-1
2014-1
2414-1
3214-1
1
1-1/4
1-1/2
2
Back Ferrule
PARKER
PART NO.
INTERCHANGES
WITH
MM
TUBE
O.D.
For metric tube
BFM2
BFM3
BFM4
BFM6
BFM8
2M4-1
3M4-1
4M4-1
6M4-1
8M4-1
2
3
4
6
8
BFM10
BFM12
BFM14
BFM15
BFM16
10M4-1
12M4-1
14M4-1
15M4-1
16M4-1
10
12
14
15
16
BFM18
BFM20
BFM22
BFM25
18M4-1
20M4-1
22M4-1
25M4-1
18
20
22
25
PARKER
PART NO.
Back Ferrule
For fractional tube
For stainless steel,

sizes 4-32 are
Suparcase ferrules.
METRIC
FFM
Ferrule Holder
Package simplifies
ordering, stocking,
and assembling
BFM
For stainless steel,

sizes 6mm25mm are
Suparcase ferrules.
CPI
PART NO.
1 HOLDER
A-LOK
PART NO.
1 HOLDER
T
TUBE O.D.
(INCHES)
CPI
PART NO.
1 HOLDER
A-LOK
PART NO.
1 HOLDER
T
TUBE O.D.
(MM)
2 CPI-*-SET
4 CPI-*-SET
6 CPI-*-SET
8 CPI-*-SET
12 CPI-*-SET
16 CPI-*-SET
2 ALOK-*-SET
4 ALOK-*-SET
6 ALOK-*-SET
8 ALOK-*-SET
12 ALOK-*-SET
16 ALOK-*-SET
1/8
1/4
3/8
1/2
3/4
1
6M CPI-*-SET
8M CPI-*-SET
12M CPI-*-SET
6M ALOK-*-SET
8M ALOK-*-SET
12M ALOK-*-SET
6
8
12
*Material designator 316-SS,

B-Brass, S-Steel
*Material designator 316-SS,

B-Brass, S-Steel
The Parker ferrule holder

offers a new convenience.
The holder contains individual ferrule sets. Ferrule sets
may be dispensed one
at a time.
69
Components
FNZ, BLP
Plug
For fractional tube
For plugging open ended
CPI/A-LOK fitting ends
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
1 FNZ
2 FNZ
3 FNZ
4 FNZ
5 FNZ
1BLP1
2BLP2
3BLP3
4BLP4
5BLP5
100-P
200-P
300-P
400-P
500-P
1/16
1/8
3/16
1/4
5/16
10-32
5/16-20
3/8-20
7/16-20
1/2-20
.31
.47
.47
.50
.53
5/16
7/16
1/2
9/16
5/8
6 FNZ
8 FNZ
10 FNZ
12 FNZ
14 FNZ
6BLP6
8BLP8
10BLP10
12BLP12
14BLP14
600-P
810-P
1010-P
1210-P
1410-P
3/8
1/2
5/8
3/4
7/8
9/16-20
3/4-20
7/8-20
1-20
1-1/8-20
.56
.69
.69
.69
.69
11/16
7/8
1
1-1/8
1-1/4
16 FNZ
20 FNZ
24 FNZ
32 FNZ
16BLP16
20BLP20
24BLP24
32BPL32
1610-P
2010-P
2410-P
3210-P
1
1-1/4
1-1/2
2
1-5/16-20
1-5/8-20
1-15/16-20
2-5/8-20
.81
1.35
1.72
2.27
1-1/2
1-7/8
2-1/4
3
TUBE
O.D.
THREAD
W
HEX
HOW TO
ASSEMBLE
Wrench tighten
only 1/4 turn
from finger tight
position.
Assembly
includes
machined ferrule
with lock ring.

W HEX
FNZ, BLPM
Plug
For metric tube
For plugging open ended
CPI/A-LOK fitting ends
MILLIMETERS
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
FNZ 2
FNZ 3
FNZ 4
FNZ 6
FNZ 8
BLPM2
BLPM3
BLPM4
BLPM6
BLPM8
2MO-P
3MO-P
4MO-P
6MO-P
8MO-P
2
3
4
6
8
5/16-20
5/16-20
3/8-20
7/16-20
1/2-20
11,9
11,9
11,9
12,7
13,5
12,0
12,0
12,0
14,0
16,0
FNZ 10
FNZ 12
FNZ 14
FNZ 15
FNZ 16
BLPM10
BLPM12
BLPM14
BLPM15
BLPM16
10MO-P
12MO-P
14MO-P
15MO-P
16MO-P
10
12
14
15
16
5/8-20
3/4-20
7/8-20
7/8-20
7/8-20
15,1
17,5
17,5
17,5
17,5
19,0
22,0
25,0
25,0
25,0
FNZ 18
FNZ 20
FNZ 22
FNZ 25
BLPM18
BLPM20
BLPM22
BLPM25
18MO-P
20MO-P
22MO-P
25MO-P
18
20
22
25
1-20
1-1/8-20
1-1/8-20
1-5/16-20
17,5
17,5
17,5
20,6
30,0
32,0
32,0
38,0
TUBE
O.D.
THREAD
W
HEX
HOW TO
ASSEMBLE
Wrench tighten
only 1/4 turn
from finger
tight position.
Assembly
includes
machined ferrule
with lock ring.

W HEX
PNBZ, BLEN
Cap
For fractional tube
For capping open ended tubing
A
C
W HEX
INCHES
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
W
HEX
1 PNBZ
2 PNBZ
3 PNBZ
4 PNBZ
5 PNBZ
1BLEN1
2BLEN2
3BLEN3
4BLEN4
5BLEN5
100-C
200-C
300-C
400-C
500-C
1/16
1/8
3/16
1/4
5/16
.56
.79
.84
.92
.96
.43
.60
.64
.70
.73
5/16
7/16
7/16
1/2
9/16
6 PNBZ
8 PNBZ
10 PNBZ
12 PNBZ
14 PNBZ
6BLEN6
8BLEN8
10BLEN10
12BLEN12
14BLEN14
600-C
810-C
1010-C
1210-C
1410-C
3/8
1/2
5/8
3/4
7/8
1.01
1.15
1.18
1.25
1.31
.76
.87
.87
.87
.87
5/8
13/16
15/16
1-1/16
1-3/16
16 PNBZ
20 PNBZ
24 PNBZ
32 PNBZ
16BLEN16
20BLEN20
24BLEN24
32BLEN32
1610-C
2010-C
2410-C
3210-C
1
1-1/4
1-1/2
2
1.52
2.09
2.53
3.41
1.05
1.52
1.77
2.47
1-3/8
1-3/4
2-1/8
2-3/4

NOTE: For body only specify PNZ
70
Components
PNBZ,
BLENM
Cap
For metric tube
For capping open ended
tubing
A
C
MILLIMETERS
CPI
PART NO.
A-LOK
PART NO.
INTERCHANGES
WITH
TUBE
O.D.
W
HEX
PNBZ 2
PNBZ 3
PNBZ 4
PNBZ 6
PNBZ 8
BLENM2
BLENM3
BLENM4
BLENM6
BLENM8
2MO-C
3MO-C
4MO-C
6MO-C
8MO-C
2
3
4
6
8
13,5
13,5
14,3
15,9
17,1
15,3
15,3
16,1
17,7
18,6
12,0
12,0
12,0
14,0
15,0
PNBZ 10
PNBZ 12
PNBZ 14
PNBZ 15
PNBZ 16
BLENM10
BLENM12
BLENM14
BLENM15
BLENM16
10MO-C
12MO-C
14MO-C
15MO-C
16MO-C
10
12
14
15
16
19,1
19,1
19,8
19,8
19,8
19,5
22,0
22,0
22,0
22,0
18,0
22,0
24,0
24,0
24,0
PNBZ 18
PNBZ 20
PNBZ 22
PNBZ 25
BLENM18
BLENM20
BLENM22
BLENM25
18MO-C
20MO-C
22MO-C
25MO-C
18
20
22
25
21,3
23,9
23,9
26,2
22,0
22,0
22,0
26,5
27,0
30,0
30,0
35,0
NOTE: For body only specify PNZ.

W HEX
MDF
Vent Protector
NPT Male Pipe
Thread
For fractional tube
INCHES
CPI/A-LOK PART NO.
INTERCHANGES
WITH
THREAD
SIZE
2 MDF
4 MDF
6 MDF
8 MDF
12 MDF
16 MDF
MS-MD-2M
MS-MD-4M
MS-MD-6M
MS-MD-8M
MS-MD-12M
MS-MD-16M
1/8-27
1/4-18
3/8-18
1/2-14
3/4-14
1-11-1/2
.63
.81
.81
1.06
1.13
1.31
E
MINIMUM
OPENING
W
HEX
FLAT
.38
.56
.56
.75
.75
.95
.19
.28
.41
.50
.63
.94
9/16
9/16
11/16
7/8
1-1/16
1-3/8
A
R
Parker Instrumentation vent protectors (mud dauber fittings) protect open ends of instruments, tubing, outlet vents,
etc.
The mesh wire screen prevents foreign bodies such as insects or debris from entering and clogging various systems
and causing damage.
pipe plug, bored-thru design
40 x 40 mesh, .010 diameter wire screen
designed to vent female pipe, straights, elbows or tees.
W HEX
71
Components
SEALING WASHERS
Bonded Seals
Consists of an outer stainless steel
ring with a Viton inner ring used to
seal a male ISO parallel thread.
PRESSURE RATINGS FOR SEALING WASHERS
CPI/A-LOK
PART NO.
T
BSPP
THREAD
M30201-SS
M30202-SS
M30203-SS
M30204-SS
M30206-SS
M30208-SS
1/8
1/4
3/8
1/2
3/4
1
.63
.81
.94
1.12
1.38
1.69
.08
.08
.08
.10
.10
.10
THREAD SIZE
PSI
BAR
1/8
1/4
3/8
1/2
3/4
1
5300
5500
4400
4000
3700
2800
370
380
300
280
260
190
These seals are also available in steel with a Nitrile inner ring.
Simply replace Suffix SS with S
H
T
D
Copper Washers
H
d
D
For BSPP male thread sealing
For BSPP female thread sealing
CPI/A-LOK
PART NO.
THREAD
CPI/A-LOK
PART NO.
THREAD
M28329
M28330
M28331
M28332
M28334
M28336
1/8
1/4
3/8
1/2
3/4
1
.71
.87
.94
1.18
1.38
1.65
.39
.55
.67
.87
1.06
1.34
.09
.09
.09
.10
.09
.09
M25179
M25180
M25181
M25182
M25184
M25186
1/8
1/4
3/8
1/2
3/4
1
.322
.436
.574
.719
.935
1.178
.218
.312
.437
.562
.812
1
.062
.062
.062
.062
.062
.093
Used to provide a seal with male or female parallel ISO threads.

Please note the pressure ratings are based on taper threaded ends. The pressure
rating for the BSPP ends are dependent on the type of sealing washer used.
72
Components
WLZ
Bulkhead Locknut
For fractional tube
A
W HEX
INCHES
CPI/A-LOK
PART NO.
INTERCHANGES
WITH
A-LOK
THREAD
TUBE
O.D.
W
HEX
1 WLZ
2 WLZ
3 WLZ
4 WLZ
5 WLZ
102-61
202-61
302-61
402-61
502-61
10-32
5/16-20
3/8-20
7/16-20
1/2-20
1/16
1/8
3/16
1/4
5/16
.13
.19
.22
.22
.23
5/16
1/2
9/16
5/8
11/16
6 WLZ
8 WLZ
10 WLZ
12 WLZ
14 WLZ
602-61
812-61
1012-61
1212-61
1412-61
9/16-20
3/4-20
7/8-20
1"-20
1-1/8-20
3/8
1/2
5/8
3/4
7/8
.25
.28
.31
.34
.38
3/4
15/16
1-1/16
1-3/16
1-3/8
16 WLZ
1612-61
1-5/16-20
.38
1-5/8
WLN
INCHES
Bulkhead Locknut
For fractional tube
A
CPI/A-LOK
PART NO.
SAE ADJ.
STR. THREAD
TUBE
O.D.
W
HEX
4 WLN
6 WLN
8 WLN
12 WLN
16 WLN
7/16-20
9/16-18
3/4-16
1-1/16-12
1-5/16-12
1/4
3/8
1/2
3/4
1
.28
.27
.31
.41
.41
11/16
13/16
1
1-3/8
1-5/8
W HEX
BN
MILLIMETERS
Bulkhead Locknut
For metric tube
A
W HEX
PARKER
PART NO.
SAE ADJ.
STR. THREAD
TUBE
O.D.
W
HEX
2BN2
3BN3
4BN4
5BN5
BNM10
5/16-20
3/8-20
7/16-20
1/2-20
5/8-20
2&3
4
6
8
10
4,8
5,6
5,6
5,6
6,4
13,0
14,0
16,0
17,0
21,0
8BN8
10BN10
12BN12
14BN14
16BN16
3/4-20
7/8-20
1-20
1-1/8-20
1-5/16-20
12
14, 15 & 16
18
20 & 22
25
7,1
7,9
8,6
9,7
9,7
24,0
27,0
30,0
33,0
41,0
L5N
INCHES
Accessory Locknut
A
W HEX
CPI/A-LOK
PART NO.
STRAIGHT
THREAD
W
HEX
2 L5N
3 L5N
4 L5N
5 L5N
6 L5N
5/16-24
3/8-24
7/16-20
1/2-20
9/16-18
.22
.22
.28
.28
.28
7/16
1/2
9/16
5/8
11/16
8 L5N
10 L5N
12 L5N
14 L5N
16 L5N
3/4-16
7/8-14
1-1/16-12
1-3/16-12
1-5/16-12
.31
.36
.41
.41
.41
7/8
1
1-1/4
1-3/8
1-1/2

NOTE: For use with M2SC and M2TU fittings on pages 54 and 55.
73
Engineering Report
Assembly and Remake Instructions
INCH SIZE 1 thru 3
(1/16" - 3/16")
METRIC SIZE 2 thru 4
(2-4mm)
Only 3/4 turn from finger

tight is necessary to seal
and will result in additional
remakes of the fitting
INCH SIZE 4 thru 16
(1/4" - 1")
METRIC SIZE 6 thru 25
(6-25mm)
1. Parker instrument tube fittings are sold completely assembled and ready for immediate use. Simply insert the tube as
illustrated until it bottoms in the fitting body. (If the fitting is disassembled, note that the small tapered end of the ferrule(s) go
into the fitting body.)
2. Tighten nut finger tight. Then tighten nut with wrench an
additional 1-1/4 turns indicated below. Hold fitting body with
a second wrench to prevent body from turning. It is helpful
to mark the nut to facilitate counting the number of turns.
For maximum number of remakes, mark the fitting and nut
before disassembly. Before retightening, make sure the
assembly has been inserted into the fitting until the ferrule
seats in the fitting. Retighten the nut by hand. Rotate the nut
with a wrench to the original position as indicated by the previous marks lining up. (A noticeable increase in mechanical
resistance will be felt indicating the ferrule is being re-sprung
into sealing position.)
Only after several remakes will it become necessary to advance
the nut slightly past the original position. This advance (indicated by B) need only be 10-20 (less than 1/3 of a hex flat).
For Sizes above 16 (1"), the Parker IPD Hydraulic
Presetting Tool or Rotary Wrench Tool should be used.
Cat. 4290-INST.
1-1/4 Turns from

Finger Tight
A
B
Parker CPI/A-LOK Tube Fitting part numbers use symbols to identify the size, style, and material. Tube and pipe thread
sizes begin with a number indicating their size in sixteenths of an inch. For example, 4=4/16 or 1/4; 16=16/16 or 1.
NOTE: Lubrication of the nut is REQUIRED for proper assembly on all LARGER size fittings in both inch and metric
sizes. This requirement applies to:
inch sizes of 20 and higher
metric sizes of 25 and higher
For additional information please contact your local authorized Parker Instrumentation distributor
or call Parker Instrumentation Products Division and ask for Bulletin 4230-B10.
Gaugeability Instructions
1. From finger tight position, wrench 1-1/4 turns for 1/4" to 1"
size fittings (6mm to 25mm) (1/16", 1/8", 3/16", 2mm 3mm
and 4mm size tube fittings only wrench 3/4 turn from finger
tight position). Hold fitting body hex with second wrench to
prevent body from turning as you tighten. It is a good idea to
mark the nut (scribe or ink) to help you count the turns.
2. Now select the proper size inspection gauge and try to

place it, as shown, between the nut and the body hex. If
gauge DOES NOT FIT AT ANY POINT between them, you
have correctly tightened the nut. If you can slip the gauge into
the space, the fitting is not properly made up, and you must
repeat the assembly procedure.
For additional information please contact your local authorized Parker Instrumentation distributor
or call Parker Instrumentation Products Division and ask for Bulletin 4230-B15.2.
74
Instrument Tubing Selection Guide

Parkers instrument tube fittings have been designed to work in a wide variety of applications that demand the utmost in
product performance.
Although Parkers Instrument tube fittings have been engineered and manufactured to consistently provide this level of
reliability, no systems in-tegrity is complete without considering the critical link, tubing.
This booklet is intended to assist the designer to properly select and order quality tubing.
Proper tube selection and installation, we believe, are key ingredients in building leak-free reliable tubing systems.
General Selection Criteria

The most important consideration in the selection of suitable tubing for any application is the compatibility of the tubing material with the media to be contained. Table 1 lists common materials and their associated general application. Table 1 also lists
the maximum and minimum operating temperature for the various tubing materials.
In addition, Parker instrument fittings are designed to work on like materials. Stainless steel fittings should be used only with
stainless steel tubing, aluminum fittings with aluminum tubing, etc. The practice of mixing materials is strongly discouraged.
The only exception is brass fittings with copper tubing.
Dissimilar materials in contact may be susceptible to galvanic corrosion. Further, different materials have different levels of
hardness, and can adversely affect the fittings ability to seal on the tubing.
TUBING
MATERIAL
RECOMMENDED
TEMPERATURE RANGE
GENERAL APPLICATION
Stainless Steel
High Pressure, High Temperature, Generally

Corrosive Media
-425F to 1,200F
(-255C to 605C)
Carbon Steel
High Pressure, High Temperature Oil, Air,

Some Specialty Chemicals
-20F to 800F
(-29C to 425C)
Cooper
Low Temperature, Low Pressure Water,

Oil, Air
-40F to 400F
(-40C to 205C)
Aluminum
Low Temperature, Low Pressure Water, Oil, Air,

Some Specialty Chemicals
-40F to 400F
(-40C to 205C)
Monel 400
Recommended for Sour Gas Applications

Well Suited for Marine and General Chemical
Processing Applications
-325F to 800F
(-198C to 425C)
Alloy C276
Excellent Corrosion Resistance to Both Oxidizing

and Reducing Media and Excellent Resistance to
Localized Corrosion Attack
-325F to 1000F
(-198C to 535C)
Carpenter 20
Applications Requiring Resistance to Stress

Corrosion Cracking in Extreme Conditions
-325F to 800F
(-198C to 425C)
Alloy 600
Recommended for High Temperature

Applications with Generally Corrosive Media
-205F to 1200F
(-130C to 650C)
Titanium
Resistant to Many Natural Environments such as

Sea Water, Body Fluids and Salt Solutions
-75F to 600F
(-59C to 315C)
Carpenter 20 is a trademark of Carpenter Technology Corporation.

Monel 400 is a trademark of International Nickel.
1. For operating temperatures above 800 F (425 C), consideration should be given to media. 300 Series Stainless Steels are suspectible to carbide
precipitation which may lead to intergranular corrosion at elevated temperatures.
2. Consideration should be given to maximum temperature ratings if fittings and/or tubing are coated or plated.
All temperature ratings based on temperatures per ASME/ANSI B31-3 Chemical Plant and Petroleum Refinery Piping Code, 1999 Edition.
The information listed in Table 1 is general in scope. For specific applications, please contact Parkers Instrumentation Products Division, Product
Engineering Department (256) 881-2040.
75

Gas Service
Special care must be taken when selecting tubing for gas service. In order to achieve a gas-tight seal, ferrules in instrument fittings must seal any surface imperfections. This is accomplished by the ferrules penetrating the surface of the tubing.
Penetration can only be achieved if the tubing provides radial resistance and if the tubing material is softer than the ferrules.
Thick walled tubing helps to provide resistance. Tables 2-7 indicate the minimum acceptable wall thickness for various materials in gas service. The ratings in white indicate combination of diameter and wall thickness which are suitable for gas service.
Acceptable tubing hardness for general application is listed in Table 9. These values are the maximum allowed by ASTM. For
gas service, better results can be obtained by using tubing well below this maximum hardness. For example, a desirable hardness of 80 Rb is suitable for stainless steel. The maximum allowed by ASTM is 90 Rb.
System Pressure
The system operating pressure is another important factor in determining the type, and more importantly, the size of tubing to
be used. In general, high pressure installations require strong materials such as steel or stainless steel. Heavy walled softer
tubing such as copper may be used if chemical compatibility exists with the media. However, the higher strength of steel or
stainless steel permits the use of thinner tubes without reducing the ultimate rating of the system. In any event, tube fitting
assemblies should never be pressurized beyond the recommended working pressure.
The following tables (2-7) list by material the maximum suggested working pressure of various tubing sizes. Acceptable tubing
diameters and wall thicknesses are those for which a rating is listed. Combinations, which do not have a pressure rating, are
not recommended for use with instrument fittings.
MAXIMUM ALLOWABLE WORKING PRESSURE TABLES
Tube
O.D.
Size
WALL THICKNESS
.010
.012
.014
.016
.020
.028
.035
.049
.065
1/16
16800
1/8
8600
10900
3/16
5500
7000
10300
1/4
4000
5100
7500
10300
5/16
4100
5900
8100
3/8
3300
4800
6600
3700
1/2
.083
.095
.109
5100
6700
5/8
4000
5200
6100
3/4
3300
4300
5000
5800
7/8
3600
4200
4900
3200
3700
4200
1-1/4
3300
1-1/2
.120
.134
1/16
1/8
3/16
1/4
5/16
3/8
1/2
5/8
3/4
7/8
1
1-1/4
1-1/2
2
.010
.012
.014
.016
.020
.028
14300
7300
4700
3400
.035
WALL THICKNESS
.049 .065 .083
9300
6000
4400
3400
8700
6400
5000
4100
3200
8700
6900
5600
4300
3400
2800
2400
5700
4500
3700
3100
2700
.095
5200
4200
3600
3100
.109
4900
4200
3600
2800
.188
4700
3700
4100
4900
3000
3400
4000
4500
2900
3200
Tube
O.D.
Size
.156
.120
.134
.156
.188
4000
3100
2600
3500
2900
4200
3400
2500
4200
3000
76
Tube
O.D.
Size
1/8
3/16
1/4
5/16
3/8
1/2
5/8
3/4
7/8
1
1-1/4
1-1/2
2
.028
.035
8100 10300
5200 6700
4900
3800
3100
.049
9700
7100
5500
4500
3300
.065
9700
7700
6200
4500
3500
2900
.083
WALL THICKNESS
.095
.109
.120
6000
4600
3800
3200
2800
5400
4400
3700
3200
5100
4300
3700
2900
4100
3200
.134
.148
3700 3800
3000 3400
Tube
T
WALL THICKNESS
O.D. .010 .020 .028 .035 .049 .065 .083 .095 .109 .120
Size
Tube
O.D.
Size
1/16 1700 3800 5400 6000

1/8
3600
3/16
1800 2300 3500
1/4
1700 2600 3500
5/16
1300 2000 2800
3/8
1100 1600 2300
1/2
1200 1600 2200
5/8
1700 2000
3/4
1000 1400 1600 1900
7/8
1100 1300 1600
1
1000 1200
1500
1 1/8
900 1000 1200 1300
1/16
1/8
3/16
1/4
5/16
3/8
1/2
5/8
3/4
1
.165
Tube
O.D.
Size
.180
1/8
3/16
1/4
15/16
3/8
1/2
5/8
3/4
7/8
1
3800
2800
4000
3000
.010
.020
5900
12600 17000
8600
5500
4000
Note: All working pressures have been calculated

using the maximum allowable stress levels in
accordance with ANSI B31.3, Chemical Plant
and Petroleum Refinery Piping Code, 1999
Edition.
.028
WALL THICKNESS
.035
8700
5600
4100
3200
2600
1900
.049
.065
8100
5900
4600
3800
2800
2200
1800
1500
.083
.095
3800
2900
2400 3200
2100 2700
1800 2300 2700
WALL THICKNESS
.035 .049 .065 .083
.095
.109
.120
11000
7100 10300
5100 7500 10300
4000 5900 8100
3300
6600
3300 4500 5900
3700 4900
3100 4000
2900
5700
4600
3400
5400
3900
4400
All calculations are based on maximum outside

diameter and minimum wall thickness.
All working pressures are ambient (72oF or 22oC)
temperature.
System Temperature
Operating temperature is another factor in determining the proper tubing material. Copper and aluminum tubing are suitable for low temperature media.
Stainless steel and carbon steel tubing are suitable for higher temperature media. Special alloys such as Alloy 600 are recommended for extremely high
temperatures (see Table 1). Table 8 lists derating factors which should be applied to the working pressures listed in Tables 2-7 for elevated temperature
conditions. Simply locate the correct factor in Table 8 and multiply this by the appropriate value in Tables 2-7 for elevated temperature working pressure.
Table 8
Temperature
F
(C)
100
(38)
200
(93)
300
(149)
400
(204)
500
(260)
600
(316)
700
(371)
800
(427)
900
(486)
1000
(538)
1100
(593)
1200
(649)
Temperature Derating Factors

Copper
1.00
.80
.78
.50
Aluminum
1.00
1.00
.81
.40
316 SS
1.00
1.00
1.00
.97
.90
.85
.82
.80
.78
.77
.62
.37
304 SS
1.00
1.00
1.00
.94
.88
.82
.80
.76
.73
.69
.49
.30
Steel
1.00
.96
.90
.86
.82
.77
.73
.59
Monel
400
1.00
.88
.82
.79
.79
.79
.79
.76
EXAMPLE: 1/2 inch x .49 wall seamless 316 stainless steel tubing has a working pressure of 3700 psi @ room temperature. If the system were to
operate @ 800oF (425oC), a factor of 80% or (.80) would apply (see Table 8 above) and the at temperature system pressure would be 3700 PSI x
.80 = 2960 PSI.
77

Tubing Ordering Suggestions
Tubing for use with Parker instrument fittings must be carefully ordered to insure adequate quality for good performance. Each
purchase order must specify the material nominal outside diameter, and wall thickness. Ordering to ASTM specifications
insures that the tubing will be dimensionally, physically, and chemically within strict limits. Also, more stringent requirements
may be added by the user. All tubing should be ordered free of scratches and suitable for bending.
A purchase order meeting the above criteria would read as follows:
1/2 x .049 316 stainless steel, seamless, or welded and redrawn per ASTM A-249. Fully annealed, 80 Rb or less.
Must be suitable for bending; surface scratches, and imperfections (incomplete weld seams) are not permissible.
Table 9 lists specific ordering information for each material.
Table 9
Material
Type
ASTM Tubing Spec.
Condition
Max. Recommended
Hardness
Stainless Steel
304, 316, 316L
Fully Annealed
90 Rb
Copper
K or L
ASTM-A-269, A-249,
A-213, A632
ASTM-B75
B68, B88 (K or L)*
SAE-J524b, J525b
ASTM-A-179
ASTM B-210
ASTM B-165
ASTM-B-622, B-626
ASTM B-167
ASTM B-468
ASTM B-338
Soft Annealed
Temper 0
Fully Annealed
60 Max.
Rockwell 15T
72 Rb
T6 Temper
Fully Annealed
Fully Annealed
Fully Annealed
Fully Annealed
Fully Annealed
56 Rb
75 Rb
90 Rb
90 Rb
90 Rb
99 Rb
200 Brinell Typical
Carbon Steel
1010
Aluminum
Monel
Alloy C-276
Alloy 600
Carpenter 20
Titanium
Alloy 6061
400
C-276
600
20CB-3
Commercially
Pure Grade 2
* Note: B88 Copper Tube to be ordered non-engraved
Pipe Pressure Ratings

NPT/BSPT
NPT/BSPT
BRASS
STAINLESS STEEL
Female
Male
Female
Male
Straight a
Shape b
Straight a
Shape b
Straight a
Shape b
Straight a
1/16
6000
5500
4500
3800
1/8
5600
5000
4000
2900
1/16
10000
9500
7500
7000
1/8
9100
9100
6400
1/4
4100
4100
4300
5500
3000
1/4
7500
7500
6600
3/8
4000
4000
5600
3500
2700
3/8
7200
7200
5300
1/2
3900
5000
3100
3600
2500
1/2
6600
5800
5200
3/4
4500
3800
3400
3000
2000
3/4
6400
6400
4300
3500
2700
2700
3100
2300
4600
4600
4500
3900
1 1/4
2000
2000
2300
1900
1 1/4
3500
3500
3500
3100
1 1/2
1800
1800
2100
1700
1 1/2
2900
2900
3200
2500
1600
1600
2000
1500
2600
2600
2700
2300
Female
Male
Straight a
1/16
Shape
Straight a
10100
Shape b
7500
1/8
9700
9700
6800
1/4
8000
8000
5900
3/8
7600
7600
1/2
7000
6200
3/4
6800
6800
4600
3700
4900
4900
4800
4200
1 1/4
3700
3700
3700
3300
1 1/2
3100
3100
3400
2600
2800
2800
2800
2400
6000
5600
5300
4800
Notes:
1
d. Pressure ratings for fittings with both tube and
pipe ends are rated to the lower pressure
78
Thread and Tube End

Size Chart (U.S.A.)
NPT
Thread
NPT
Thread
1/16"
(1/16"-27")
Tubing O.D. Size
Straight
StraightThread
Thread
1/8"
(1/8"-27")
5/16"-24"
7/16"-20"
1/16"
1/8"
1/4"
(1/4"-18")
3/16"
1/2"-20"
1/4"
3/8"
(3/8"-18")
9/16"-18"
5/16"
3/8"
1/2"
(1/2"-14")
3/4"-16"
1/2"
5/8"
3/4"
(3/4"-14")
7/8"-14"
3/4"
1-1/16"-12"
1"
(1"-11 1/2")
AmericanStandard
Standard
American
Pipe
Thread
(NPT)
Pipe Thread (NPT)
7/8"
American Standard
American
Standard
Unified Thread (Straight)
Unified
(Straight)
1"
60 thread angle Pitch measured in inches

Truncation of root and crest are flat
Taper angle 147'

Truncation of root and crest are flat
Diameter measured in inches
79
Pipe and Tube End

Size Chart (U.S.A.)
Tubing O.D.
Tubing
O.D. Size
Size
NPT
NPTThread
Thread
1-1/4"
(1-1/4"- 11 1/2")
1-1/4"
1-1/2"
1-1/2"
(1-1/2"- 11 1/2")
2"
(2"- 11 1/2")
2"
80
Thread and Tube End

Size Chart (International)
Tubing O.D. Size
BSPP
Parallel Thread
BSPT
Tapered Thread
1/8"
(1/8-28)
(1/8"-28")
1/8"
(1/8-28)
(1/8"-28")
2mm
3mm
4mm
6mm
1/4"
(1/4-19)
(1/4"-19")
1/4"
(1/4-19)
(1/4"-19")
8mm
10mm
3/8"
(3/8-19)
(3/8"-19")
3/8"
(3/8-19)
(3/8"-19)"
12mm
14mm
1/2"
(1/2-14)
(1/2"-14")
1/2"
(1/2-14)
(1/2"-14")
15mm
16mm
3/4"
(3/4-14)
(3/4"-14")
3/4"
(3/4-14)
(3/4"-14")
18mm
20mm
1"
(1"-11)
(1"-11")
1"
(1"-11)
(1"-11")
22mm
International Organization
Organization for
International
for Standards
Standards
(ISO
(ISO
(ISO7/1)
7/1)
(ISO228/1)
228/1)
25mm
Truncation of root and crest are round
Taper angle 147'

Truncation of root and crest are round
Diameter measured in inches
81
Offer of Sale
The items described in this document and other documents or descriptions provided by Parker Hannifin Corporation, its subsidiaries and its authorized distributors are hereby offered for sale at prices to be established by Parker Hannifin Corporation, its subsidiaries and its authorized distributors.
This offer and its acceptance by any customer ("Buyer") shall be governed by all of the following Terms and Conditions. Buyers order for any such
items, when communicated to Parker Hannifin Corporation, its subsidiary or an authorized distributor ("Seller") verbally or in writing, shall constitute
acceptance of this offer.
1. Terms and Conditions of Sale: All descriptions, quotations, proposals,
offers, acknowledgments, acceptances and sales of Sellers products are
subject to and shall be governed exclusively by the terms and conditions
stated herein. Buyers acceptance of any offer to sell is limited to these terms
and conditions. Any terms or conditions in addition to, or inconsistent with
those stated herein, proposed by Buyer in any acceptance of an offer by
Seller, are hereby objected to. No such additional, different or inconsistent
terms and conditions shall become part of the contract between Buyer and
Seller unless expressly accepted in writing by Seller. Sellers acceptance
of any offer to purchase by Buyer is expressly conditional upon Buyers
assent to all the terms and conditions stated herein, including any terms in
addition to, or inconsistent with those contained in Buyers offer, Acceptance
of Sellers products shall in all events constitute such assent.
2. Payment: Payment shall be made by Buyer net 30 days from the date
of delivery of the items purchased hereunder. Amounts not timely paid
shall bear interest at the maximum rate permitted by law for each month
or portion thereof that the Buyer is late in making payment. Any claims by
Buyer for omissions or shortages in a shipment shall be waived unless Seller
receives notice thereof within 30 days after Buyers receipt of the shipment.
3. Delivery: Unless otherwise provided on the face hereof, delivery shall
be made F.O.B. Sellers plant. Regardless of the method of delivery, however, risk of loss shall pass to Buyer upon Sellers delivery to a carrier. Any
delivery dates shown are approximate only and Seller shall have no liability
for any delays in delivery.
4. Warranty: Seller warrants that items sold hereunder shall be free
from defects in material or workmanship. THIS WARRANTY COMPRISES
THE SOLE AND ENTIRE WARRANTY PERTAINING TO ITEMS PROVIDED HEREUNDER. SELLER MAKES NO OTHER WARRANTY,
GUARANTEE, OR REPRESENTATION OF ANY KIND WHATSOEVER.
ALL OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS FOR PURPOSE, WHETHER EXPRESS,
IMPLIED, OR ARISING BY OPERATION OF LAW, TRADE USAGE, OR
COURSE OF DEALING ARE HEREBY DISCLAIMED.
NOTWITHSTANDING THE FOREGOING, THERE ARE NO WARRANTIES WHATSOEVER ON ITEMS BUILT OR ACQUIRED WHOLLY OR
PARTIALLY, TO BUYERS DESIGNS OR SPECIFICATIONS.
5. Limitation Of Remedy: SELLERS LIABILITY ARISING FROM OR IN
ANY WAY CONNECTED WITH THE ITEMS SOLD OR THIS CONTRACT
SHALL BE LIMITED EXCLUSIVELY TO REPAIR OR REPLACEMENT
OF THE ITEMS SOLD, AT SELLERS SOLE OPTION. IN NO EVENT
SHALL SELLER BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY KIND OR NATURE WHATSOEVER, INCLUDING BUT NOT LIMITED TO LOST PROFITS ARISING
FROM OR IN ANY WAY CONNECTED WITH THIS AGREEMENT OR
ITEMS SOLD HEREUNDER, WHETHER ALLEGED TO ARISE FROM
BREACH OF CONTRACT, EXPRESS OR IMPLIED WARRANTY, OR IN
TORT, INCLUDING WITHOUT LIMITATION, NEGLIGENCE, FAILURE
TO WARN OR STRICT LIABILITY.
6. Changes, Reschedules and Cancellations: Buyer may request to
modify the designs or specifications for the items sold hereunder as well
as the quantities and delivery dates thereof, or may request to cancel all
or part of this order, however, no such requested modification or cancellation
shall become part of the contract between Buyer and Seller unless accepted
by Seller in a written amendment to this Agreement. Acceptance of any
such requested modification or cancellation shall be at Sellers discretion,
and shall be upon such terms and conditions as Seller may require.
7. Special Tooling: A tooling charge may be imposed for any special tooling, including without limitation, dies, fixtures, molds and patterns, acquired
to manufacture items sold pursuant to this contract. Such special tooling
shall be and remain Sellers property notwithstanding payment of any
charges by Buyer. In no event will Buyer acquire any interest in apparatus
belonging to Seller which is utilized in the manufacture of the items sold
hereunder, even if such apparatus has been specially converted or adapted for such manufacture and not withstanding any charges paid by Buyer.
Unless otherwise agreed, Seller shall have the right to alter, discard or
otherwise dispose of any special tooling or other property in its sole discretion at any time.
8. Buyers Property: Any designs, tools, patterns, materials, drawings,

confidential information or equipment furnished by Buyer or any other
items which become Buyers property, may be considered obsolete and
may be destroyed by Seller after two (2) consecutive years have elapsed
without Buyer placing an order for the items which are manufactured using
such property, Seller shall not be responsible for any loss or damage to
such property while it is in Sellers possession or control.
9. Taxes: Unless otherwise indicated on the face hereof, all prices and
charges are exclusive of excise, sales, use, property, occupational or like
taxes which may be imposed by any taxing authority upon the manufacture, sale or delivery of the items sold hereunder. If any such taxes must
be paid by Seller or if Seller is liable for the collection of such tax, the
amount thereof shall be in addition to the amounts for the items sold.
Buyer agrees to pay all such taxes or to reimburse Seller therefore upon
receipt of its invoice. If Buyer claims exemption from any sales, use or
other tax imposed by any taxing authority, Buyer shall save Seller harmless from and against any such tax, together with any interest or penalties
thereon which may be assessed if the items are held to be taxable.
10. Indemnity For Infringement of Intellectual Property Rights: Seller
shall have no liability for infringement of any patents, trademarks, copyrights, trade dress, trade secrets or similar rights except as provided in this
Part 10. Seller will defend and indemnify Buyer against allegations of
infringement of U.S. Patents, U.S. Trademarks, copyrights, trade dress and
trade secrets (hereinafter Intellectual Property Rights). Seller will defend
at its expense and will pay the cost of any settlement or damages awarded
in an action brought against Buyer based on an allegation that an item sold
pursuant to this contract infringes the Intellectual Property Rights of a third
party. Sellers obligation to defend and indemnify Buyer is contingent on
Buyer notifying Seller within ten (10) days after Buyer becomes aware of
such allegations of infringement, and Seller having sole control over the
defense of any allegations or actions including all negotiations for settlement or compromise. If an item sold hereunder is subject to a claim that it
infringes the Intellectual Property Rights of a third party, Seller may, at its
sole expense and option, procure for Buyer the right to continue using said
item, replace or modify said item so as to make it noninfringing, or offer to
accept return of said item and return the purchase price less a reasonable
allowance for depreciation. Notwithstanding the foregoing, Seller shall
have no liability for claims of infringement based on information provided
by Buyer, or directed to items delivered hereunder for which the designs
are specified in whole or part by Buyer, or infringements resulting from the
modification, combination or use in a system of any item sold hereunder.
The foregoing provisions of this Part 10 shall constitute Sellers sole and
exclusive liability and Buyers sole and exclusive remedy for infringement
of Intellectual Property Rights.
If a claim is based on information provided by Buyer or if the design for an
item delivered hereunder is specified in whole or in part by Buyer, Buyer
shall defend and indemnify Seller for all costs, expenses or judgments
resulting from any claim that such item infringes any patent, trademark,
copyright, trade dress, trade secret or any similar right.
11. Force Majeure: Seller does not assume the risk of and shall not be
liable for delay or failure to perform any of Sellers obligations by reason of
circumstances beyond the reasonable control of Seller (hereinafter
Events of Force Majeure). Events of Force Majeure shall include without
limitation, accidents, acts of God, strikes or labor disputes, acts, laws, rules
or regulations of any government or government agency, fires, floods,
delays or failures in delivery of carriers or suppliers, shortages of materials
and any other cause beyond Sellers control.
12. Entire Agreement/Governing Law: The terms and conditions set
forth herein, together with any amendments, modifications and any different
terms or conditions expressly accepted by Seller in writing, shall constitute
the entire Agreement concerning the items sold, and there are no oral or
other representations or agreements which pertain thereto. This Agreement
shall be governed in all respects by the law of the State of Ohio. No actions
arising out of the sale of the items sold hereunder or this Agreement may
be brought by either party more than two (2) years after the cause of action
accrues.
11/98-P
82

6035 Parkland Blvd.
Cleveland, Ohio 44124-4141
Telephone: (216) 896-3000
Fax: (216) 896-4000
www.parker.com
Parkers Charter
To be a leading worldwide manufacturer of components and systems for the builders and users of durable
goods. More specifically, we will design, market and
manufacture products controlling motion, flow and
pressure. We will achieve profitable growth through
premier customer service.
Product Information
North American customers seeking product information, the location of a nearby distributor, or repair
services will receive prompt attention by calling the
Parker Product Information Center at our toll-free
number: 1-800-C-PARKER (1-800-272-7537). In Europe,
call 00800-C-PARKER-H (00800-2727-5374).
About Parker Hannifin Corporation

Parker Hannifin is a leading global motion-control
company dedicated to delivering premier customer
service. A Fortune 500 corporation listed on the New
York Stock Exchange (PH), our components and systems comprise over 1,400 product lines that control
motion in some 1,000 industrial and aerospace markets. Parker is the only manufacturer to offer its
customers a choice of hydraulic, pneumatic, and
electromechanical motion-control solutions. Our
company has the largest distribution network in its
field, with over 7,500 distributors serving nearly
400,000 customers worldwide.
The Aerospace Group is

a leader in the development,
design, manufacture and servicing of control systems and
components for aerospace and
related high-technology markets, while achieving growth
through premier customer
service.
The Climate & Industrial

Controls Group designs,
manufactures and markets system-control and fluid-handling
components and systems to
refrigeration, air-conditioning
and industrial customers
worldwide.
The Fluid Connectors

Group designs, manufactures
and markets rigid and flexible
connectors, and associated
products used in pneumatic
and fluid systems.
The Seal Group designs,

manufactures and distributes
industrial and commercial
sealing devices and related
products by providing
superior quality and total
customer satisfaction.
The Hydraulics Group

designs, produces and markets
a full spectrum of hydraulic
builders and users of industrial
and mobile machinery and
equipment.
The Filtration Group

designs, manufactures and
markets quality filtration and
clarification products, providing customers with the best
value, quality, technical support, and global availability.
The Automation Group

is a leading supplier of pneumatic and electromechanical
automation customers worldwide.
The Instrumentation
Group is a global leader in
the design, manufacture and
distribution of high-quality
critical flow components for
worldwide process instrumentation, ultra-high-purity, medical and analytical applications.
83

Instrumentation Products Division
1005 A Cleaner Way
Huntsville, AL 35805
USA
Phone: (256) 881-2040
Fax: (256) 881-5072
www.parker.com/ipdus
Parker Hannifin plc
Instrumentation Products Division
Riverside Road
Pottington Business Park
Barnstaple, Devon EX31 1NP
England
Phone: +44 (0)1271 313131
Fax: +44 (0)1271 373636
Email: [email protected]
www.parker.com/ipd
Catalog 4230/4233, 10M, 08/04 CG

A-Lok & Cpi Fittings PDF

Uploaded by

Copyright:

Available Formats

A-Lok & Cpi Fittings PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

A-Lok & Cpi Fittings PDF

Uploaded by

Copyright:

Available Formats

CPI/A-LOK

CPI/A-LOK Tube Fittings

Parker CPI /A-LOK Instrumentation Tube Fittings are

The Parker CPI/A-LOK tube fitting has been specifically

In make-up, there is no undue force in an outward direction to

Assembly, Remake, Gaugeability CPI

Pressure Rating & Tubing Selection

Parker CPI/A-LOK tube fittings are available in a wide

For working pressures of CPI/A-LOK tube connections,

Huntsville, Alabama, USA

CPI /A-LOK Tube Fittings

Parkers high quality,

Deep tube abutment

Copyright 2004, Parker Hannifin Corporation. All Rights Reserved.

CPI /A-LOK Tube Fittings

pages 8, 9, 10, 11, 12

Tube to Tube Unions

HBZ, SC, SCM

ZPC, PC, PCM

pages 38, 39, 40, 41

pages 14, 15, 16

HBZ, RU, RUM

Tube to Female Pipe

Tube to O Ring Seal

pages 42, 43, 44

pages 34, 35, 36

Tube to Male Pipe

CPI /A-LOK Tube Fittings

FNZ, BLP, BLPM

BZP Knurled Nut

Instrument Tubing Selection

BZ, NU, NUM

Pipe End Pressure Ratings

Thread and Tube End Size

CPI /A-LOK Tube Fittings

2014T (as fabricated)

Tube End Dimensional Data

NOTE: Dimensions C and D are shown in the fingertight position.

NOTE: Dimensions C and D are shown in the fingertight position.

CPI /A-LOK Tube Fittings

ignator; i.e. 4-4-4 JBZ (CPI ), 4ET4 (A-LOK ).

For easy reference, table heads

Please see visual index.

Tube to Male Pipe

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

Sizes 20, 24, 32 require additional lubrication to assembly.

Tube to Male Pipe

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

Tube to Male Pipe

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

FBZ 25-3/4K M25MSC3/4K

NOTE: A and C dimensions are typical finger-tight.

Dimensions for reference only, subject to change.

Tube to Male Pipe

NOTE: A and C dimensions are typical finger-tight.

FBZ 25-3/4R M25MSC3/4R 25MO-1-12RS