89S EUPro

EleSof
89+E UPro
89+E UPro
SST
ATMEL
WINBOND
Visit :
www.elesof.com
www.projectsmaker.com
Here is 89+E UPro USB Programmer for 89

Series Microcontroller and for Serial
EEPROM. With on board ZIF Socket for
easy insertion & removing of ICs.
Flash Programming Tool
EleSof
Development System
TO OUR VALUED CUSTOMERS
I want to express my thanks to you for being interested in our products & having
confidence in EleSof Technologies.

It is our intention to provide you with the best quality products. Furthermore, we will
continue to improve our product performance to better suit your needs.
EleSof Technologies
The ATMEL name and logo, the ATMEL logo, AVR, AVR (Logo), AVR Freaks, AVR
Freaks (Logo), AVR Studio, IDIC, megaAVR, megaAVR(Logo), picoPower , tinyAVR

are trademarks of ATMELCorporation. All other trademarks mentioned herein are
property of their respective companies and are only used for the purpose of
identification or explanation & to the owners benefit, with no intent to infringe.
Visit :
www.elesof.com
TABLE OF CONTENTS
Introduction..................4
Features.................4
Specification.............4
Package Contain...............4
Supported ICs...............5
Getting Started First Time Use.....5
Step #1: Connect Programmer to USB port & Start Software

Step #2: Install USB Driver
Step #3: Install Flashing Software
Step #4: Run Flashing Software
Troubleshooting- Failed to Connect in Software..6-7

ICs Placement...8
Flashing Steps...8-9
Step #1: Connect 89+E UPro & Run Flashing Software (89+E UPro)
Step #2: Select Device
Step #3: Load file
Step #4: Auto Program
Other Special Function ..10

Other software options ...........11
Visit :
www.elesof.com
es EleSof
USER
MANUAL
89+E UPro
5
4
89+E UPro PROGRAMMER
Introduction
89+E UPro, this programmer is
for 89 series microcontroller
devices in 20 & 40 pin packages
and supports various 8 pin serial
EEPROM ICs. ZIF socket
enables easy insertion and
removal
of
devices
for
programming. Programming is
very fast since it is USB based.
No external power required
since it is powered from USB
port itself.
Features
Simple and Easy to use

Auto Erase/Lock/Verify
Auto Identify connected programmer
Error checking and verification in-built
Leds for Programming & Power ON status.
Supports 89 series & serial EEPROM devices
40 pin ZIF socket for easy insertion & removal
High speed writing (8kb flash file in 10 seconds)
Powered from USB port(No external power required)
Informative window and access to latest programmed file
Lock of programs in chip supported to prevent program copying
Specification
Power +5V from USB Cable

Communication USB 2.0 compliant
Cable required USB A to B type for connecting PC or Laptop
Dimension 10x6.7 Cm
Package Contain
Tested & Ready to use USB Programmer

CDROM containing Flashing software, USB Driver & User Manual.
USB Cable for connecting 89+E UPro to PC
es EleSof
USER
MANUAL
89+E UPro
5
5
Supported ICs
ICs supported by 89+E UPro are mentioned below.
Atmel
AT89C51
AT89C52
AT89S51
AT89S52
AT89S53
AT89S8252
AT89C1051
AT89C2051
AT89C4051
Winbond
W78E51
W78E52
SST
SST89C54
SST89C58
SST89C59
SST89E54RD
SST89E58RD
SST89E554RC
Serial EEPROM
AT24C01
AT24C02
AT24C04
AT24C08
AT24C16
AT24C32
AT24C64
AT24C164
Serial EEPROM
AT93C46
AT93C56
AT93C66
Getting Started First Time Use

Below steps are mentioned for using 89+E UPro programmer for programming supportive ICs and this is
first time required if system change than again need to follow the same steps mentioned below to work on
that system.
Step #1: Connect Programmer to USB port & Start Software
Connect programmer to USB port RED LED permanent become ON and GREEN LED will blink once and
become off. It is normal indication of everything is ok and it is ready to use.
Step #2: Install USB Driver
Insert the CDROM provided with programmer. There will be a folder called USB Driver. It contains a
fileUsbDriver.exe clicks on that to install.
Step #3: Install Flashing Software
Install Flashing software by running its setup 89+E UPro.exe from CDROM in folder Flashing Sof-tware and follow onscreen instructions. After se tup is done, it will install icon on desktop.
Step #4: Run Flashing Software
Run Flashing Software (89+E UPro.exe). Software s hould connect and show ONLINE icon green color at
bottom. Your programmer is ready to use.
Note: Flashing Software (89+E UPro.exe), is only for Windows-XP & Windows-7
es EleSof
USER
MANUAL
89+E UPro
5
6
Troubleshooting- Failed to Connect in Software

If you get Failed to connect error in software, It is possible that virtual com port is not between COM1COM9. Change the COM port on your system from Device Manager. Also you can try Reinstalling USB
driver.
Below are the steps to change COM port on your system for 89+ E UPro programmer.
es EleSof
USER
MANUAL
89+E UPro
5
7
es EleSof
USER
MANUAL
89+E UPro
5
8
ICs Placement
Below images shows ICs placement over ZIF Socket of 89+E UPro for programming.
ATMEL
ATMEL
40B PIN
SST
ATMEl
WINBOND
Flashing Steps
TO flash ICs which supported by 89+E UPro, follow the steps mentioned below.
Step #1: Connect 89+E UPro & Run Flashing Software (89+E UPro)
Connect 89+E UPro with PC USB port, through A-B USB cable & run Flashing Software .
Note: Select 89+E UPro if programmer auto not detected
es EleSof
USER
MANUAL
89+E UPro
5
9
Step #2: Select Device

By clicking Device button to bring device selection dialog. After selecting inserted device click OK. To select
recently used devices you can click on down arrow & select.
DEVICE
Step #3: Load file

PC software takes HEX or BIN file for programming. Load > Select HEX file & click OK. To select recently
used files you can click on down arrow & select you will see following dialog when you load a HEX
extension file. You can keep all setting as default and click OK to select this file.
LOAD
Step #4: Auto Program

Click on Auto button to start programming process.
AUTO
es EleSof
USER
MANUAL
89+E UPro
5
10
Other Special Function

Locking Device to prevent copying
To set lock option for selected device click on config
config, Mode0 is no lock and other modes are other lock
options. You can see device datasheet as to which config lock bit will be suitable in your application. Once
you set a config for particular device it is stored and it is not required to set again.
Next time you program a particular device same config will be used to load in to device during Auto process.
CONFIG
Note: Before Selection Locking mode (Protection Mode) ensure your self.
es EleSof
USER
MANUAL
89+E UPro
5
11
Copying from one device to another

You may wish to copy content from one programmed IC to another. For this process, first select device and
Insert Master IC from which you want to copy program then click on READ button. It will read device
memory to buffer. If you wish to see what content was read you can click on EDIT button.
EDIT
SAVE
READ
To save this memory as HEX file you can click on SAVE button. If your master IC is locked, it will show
memory as 0xFF means its content cannot be read. Once you have saved file from master you can use this
file to load into new microcontrollers.
Other software options

Normally you will use Auto method in repeated programming task. Auto method will automatically do Erase
Blank Check, Program, Verify & Protect. We have given other options like Blank, Read, Program, Verify,
Protect & Erase, that can be used individually if you wish.
Following are methods you can use
Auto: Automatically do all process below as required to load file into device
Blank: Check if device is blank
Read: Read content of inserted device into buffer
Program: Load the content of file into device
Verify: Check if loaded file content matches with device content
Protect: Program config options to device
Erase: Erase the device.
EleSof
Development System
DISCLAIMER
This product is owned by the EleSof are protected by copyright law. Therefore, this
manual is to be treated as any other copyright material. No part of this manual,
including product & software described herein, may be reproduces, store in a retrieval
system, translated or transmitted in any form or by any means, without the prior written
permission of EleSof. The manual PDF edition can be printed for private or local use,
but not for distribution. Any modification of this manual is prohibited.
EleSof provides this manual as is without warranty of any kind, either expressed or
implied, including , but not limited to, the implied warranties or condition of
merchantability or fitness for a particular purpose.
Elesof shall assume no responsibility or liability for any errors, omissions &
inaccuracies that may appear in this manual. In no event shall EleSof, its directors,
officers, employees or distributors be liable for any indirect, specific, incidental or
consequential damages (including damages for loss of business profits & business
information, business interruption or any other pecuniary loss) arising out of the use of
this manual or product, even if EleSof has been advised of the possibility of such
damages. EleSof reserves the right to change information contained in this manual at
any time without prior notice, if necessary.
All the product, tools & corporate names appearing in this kit & manual may or may not
registered trademarks or copyright of their respective company, & are only used to
identification or explanation & to the owners benefit, with no intent to infringe.
Visit :
www.elesof.com
EleSof
Development System
HIGH RISK ACTIVITIES
The products of EleSof are not fault - tolerant nor designed, manufactured or intended
for use or resale as on line control equipment in hazardous environments requiring fail
safe performance, such as in the operation of nuclear facilities, aircraft navigation or
communication system, air traffic control, direct life support machines or weapons
system in which the failure of software could lead directly to death, personal injury or
severe physical or environment damage (High Risk Activities). EleSof & its suppliers
specifically disclaim any expressed or implied warranty of fitness for High Risk
Activities.
Copyright 2010 2012 by EleSof Technologies. All .right reserved
Visit :
www.elesof.com
EleSof
Development System
If you want to learn more about our products, please visit our website at
www.elesof.com & www.projectsmaker.com
If you have any questions, comments or business proposals, do not hesitate to contact
us.
If you are experiencing some problems with any of our products or just need additional
information, please place write mail or call to us at
[email protected] & [email protected]
+91-9911-7095-92 & +91-9044-1359-01
Visit :
www.elesof.com

89S EUPro

Uploaded by

Copyright:

Available Formats

89S EUPro

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

89S EUPro

Uploaded by

Copyright:

Available Formats

EleSof

Here is 89+E UPro USB Programmer for 89

Flash Programming Tool

confidence in EleSof Technologies.

Freaks (Logo), AVR Studio, IDIC, megaAVR, megaAVR(Logo), picoPower , tinyAVR

Step #1: Connect Programmer to USB port & Start Software

Troubleshooting- Failed to Connect in Software..6-7

Other Special Function ..10

89+E UPro PROGRAMMER

Simple and Easy to use

Power +5V from USB Cable

Tested & Ready to use USB Programmer

89+E UPro PROGRAMMER

ICs supported by 89+E UPro are mentioned below.

Getting Started First Time Use

Troubleshooting- Failed to Connect in Software

89+E UPro PROGRAMMER

89+E UPro PROGRAMMER

89+E UPro PROGRAMMER

Note: Select 89+E UPro if programmer auto not detected

Step #2: Select Device

89+E UPro PROGRAMMER

Step #3: Load file

Step #4: Auto Program

Other Special Function

89+E UPro PROGRAMMER

Copying from one device to another

89+E UPro PROGRAMMER

Other software options

Following are methods you can use

Copyright 2010 2012 by EleSof Technologies. All .right reserved

You might also like