OpenScape 4000 - V7 UC

HiPath 4000 - V6

Unified Communications Linux vServer (OS4k)

Linux Communication Server (HP4k)

Native SIP Trunk - VoIP Guide

Contents:
1. Scope
2. Card (Board) Configuration:
2.1.SUITABLE CARDS
2.2. AMO-BFDAT = Block Functional DATa for STMI Cards
2.3. AMO-BCSU = Board/Card Config. [ SU=Switching Unit ]
2.4. AMO-CGWB = Configuration of GateWay STMI Board/card; options:
2.5. INSERT the STMI card with Lan cable.
3. TRUNK CONFIGURATION - TDM/RMX SIDE....
3.1. AMO-COSSU = Class Of Service for the Trunk
3.2. AMO-COT = Class of Trunk for Call Processing
3.3. AMO-COP = Class of Parameter for Device Handler.
3.4. AMO-BUEND = Buendel = Bundle = Trunk Group
3.5. AMO-TDCSU = Trunk Digital Config.
4. LCR ROUTING ( no gkreg 4.1 /2/3 ) :
4.1. Open Number Routing: LCR with TIE Access Code + hear "external" Dial Tone (W) + SIP Provider number (Z) + #
4.2. Closed Number Routing: Dial Sip Vendor Devices (stn. number 7170 to 7199) directly...
4.3. One Number Routing Access: LCR outbound (outgoing) Sip with one fixed Number to dial.
4.4. Routing using GKREG; one STMI multiple IP destinations; no sip profile used.
4.5. Miscelaneous AMO's for US config.
4.6. Ways to convert incoming DID numbers.
5. SIP GW Web Browser Management (WBM) Settings:
5.1. Activation of SIP Trk Profile GW.
5.2. Other possible SIP GW settings
6. Troubleshooting.
6.1. Wireshark
6.2. RTDS, internal TDCSU ISDN trace
6.3. Maintenance AMO
6.4. RMX - Traces
6.5. STMI - GW Traces
6.6. STMI LoadWare ( LW )
6.7. STMI - CLI = Command Line Interface
7. SIP (STMI) x ISDN (TDCSU) messages conversion.

Changes:
1.Published = July 07, 2014.
2.Rev.=July = added item 4.4. Routing with GKREG, one STMI multiple IP destinations and item 6.6 LW.
3.Rev.=Sept.=match channels cgwb=buend=tdcsu=e.g.12 , all chann. busy = 503 Service Not Available & minor changes.
4.Update=March 2015 = added cgw comments about ports & RFC
5.Upd.=June 2015 = NatTrkEnterprise best profile for non certified apps + 1 STMI multiple GKREG destinations is supported + item 4.6
Repository: KM & http://4000.global-intra.net
Total of 26 pages.

[email protected]
Tec.Support Eng. @ Global Operations (G0)
Irving - TX 75038
USA

1. Scope:
Guide for Installation and Maintenance of NATIVE SIP TRUNKS; VoIP (Voice over Internet Protocol)
Stn. --> OS4k --> STMI GW card [ tdm/isdn trk <= conv. => SIP ] ==> Lan.Netw. --> Cloud --> VoIP Provider
2. Card (Board) Configuration:
2.1. SUITABLE IP GW CARDS
<DIS-BGDAT:N; /* BauGruppen (Board General) Data
UBGDAT BOARD TABLE
POS Q-NUMBER
TYPE BD-NAME FCTID CIRCUITS LINE-TYPE
LW-FILE
======================================================================
121
122
123
124
125

Q2316-X
Q2316-X10
Q2324-X500
Q2324-X510
Q2324-X511

186 Q2330-X

IPGW
IPGW
IPGW
IPGW
IPGW

STMI2
STMI2
STMI4
STMI4
STMI4

1
1
1
1
1

60-BChannels
120
60
120
120

LG98/PZKSTI40
LG98/PZKSTI40
LG98/PZKSTI40
LG98/PZKSTI40
LG98/PZKSTI40

IPGW

vHG3500

120

LGA0/PZKSGVB0

=> /* LW are stored on :PDS:APSP/LTG/LGxx/PZKyyyxx /*

=> SGVB=SoftGate Virtual Board

2.2. AMO-BFDAT = Block Functional DATa for STMI Cards.

ADD-BFDAT:FCTBLK=11,FUNCTION=HG3550&HG3530&SIP,BRDBCHL=BCHL120;
CHANGE-BFDAT:CONFIG=CONT,FCTBLK=11,FUNCTION=HG3550,LINECNT=2,UNITS=3; /* LineCouNT=PEN
/*set 2 lines=circ.(max.4), e.g. pen=1-3-5-0 & -1; each PEN 3x(unit=10)= 30BChan.(max.120BChan.)

CHANGE-BFDAT:CONFIG=CONT,FCTBLK=11,FUNCTION=HG3530,LINECNT=51,BCHLCNT=45;
/* above the HFA IP Phones configuration choosed additionaly to the IP Trk../*
/*on this example can add 51 HFA ports; however maximal 45 stn. can talk simultaneously /*
CHANGE-BFDAT:CONFIG=CONT,FCTBLK=11,FUNCTION=SIP,LINECNT=8,BCHLCNT=6; /* SIP Phones
CHANGE-BFDAT:CONFIG=OK,FCTBLK=11,ANSW=YES; /*OK, closing no more changes possible...
-If STMI card has only 60 BChan. choose BRDBCHL=BCHL60;
-If you choose BRDBCHL=BCHL60&BCHL120; you can use STMI with 60 or 120 Channels; however you
limit the channels to 60 no matter the card you're going to use...
-If card is exclusive for IP Trk (max.120BChann.), BFDAT does not need the HG3530 & SIP entries..
-For SoftGate vSTMI, you can not mix functions. ADD-BFDAT:FCTBLK=12,FUNCTION=HG3550,BRDBCHL=BCHL120,ATTR="SOCO";
<DIS-BFDAT:11; /* Block Functional Data for CGW (Common GW)
-------------------------------------------------------------------------------| FCTBLK = 11
BRDBCHL : BCHL120
STATUS=
OK
|
-------------------------------------------------------------------------------| 1. FUNCT : HG3550
2 LINES
UNITS 3 BCHLCNT 30 TOTAL BCHAN 60
|=> 2 lines=pen=circ. x 30 BChann.= 60 Total
| 2. FUNCT : HG3530
51 LINES
UNITS
BCHLCNT 45 TOTAL BCHAN 45
|
| 3. FUNCT : SIP
8 LINES
UNITS
BCHLCNT
6 TOTAL BCHAN
6
|
--------------------------------------------------------------------------------

2.3. AMO-BCSU = BOARD/CARD CONFIGURATION SWITCHING UNIT

ADD-BCSU:MTYPE=IPGW,LTG=1,LTU=1,SLOT=11,PARTNO="Q2316-X10",FCTBLK=11;
H34: DUE TO ACTIVATED FEATURE SIGNALLING & PAYLOAD ENCRYPTION AND/OR ACTIVATED
DMC THE NUMBER OF CONFIGURED B-CHANNELS FOR HG3530 HAVE BEEN REDUCED
BY 11 B-CHANNELS.
ACTUAL AVAILABLE HG3530 B-CHANNELS: 34
H34: DUE TO ACTIVATED FEATURE SIGNALLING & PAYLOAD ENCRYPTION AND/OR ACTIVATED
DMC THE NUMBER OF CONFIGURED B-CHANNELS FOR SIP HAVE BEEN REDUCED
BY 2 B-CHANNELS.
ACTUAL AVAILABLE SIP B-CHANNELS: 4
H34: DUE TO ACTIVATED FEATURE SIGNALLING & PAYLOAD ENCRYPTION AND/OR ACTIVATED
DMC THE NUMBER OF CONFIGURED B-CHANNELS FOR HG3570 HAVE BEEN REDUCED
BY 2 B-CHANNELS.
ACTUAL AVAILABLE HG3570 B-CHANNELS: 0
<DIS-BCSU:TBL,,1,11;
LTG 1 LTU 1
SRCGRP 1
ALARMNO-LTU 0
-----+-----------+--------+---+-+-+---+-+------------+------------+-----------|
|
|
|S|H|AL-| |
|
|
| ASSIGNED | MODULE |FCT|E|W|ARM| | INSERTED
|
HW| MODULE
PEN | MODULE
| TYPE
|ID |C|Y|NO | | MODULE
|STATE INFO | STATUS
-----+-----------+--------+---+-+-+---+-+------------+------------+-----------11 | Q2316-X10 STMI2
1 *
0|*|
|
| NPR
=> card Not PResent
+--------------------------------+-+------------+------------+-----------| IP ADDRESS :
0. 0. 0. 0
B-CHANNELS : 111
BCHLCNT : 98
| IP MODE
:
IPV4
DHCP V4
:
NO
DHCP V6 :
NO
| BLOCK NO
: 11
PRERESERVED LINES ASSIGNED :
NO
| 1. FUNCT : HG3550
2 LINES
B-CHANNELS : 60
BCHLCNT : 60
| 2. FUNCT : HG3530
51 LINES
B-CHANNELS : 45
BCHLCNT : 34
| 3. FUNCT : SIP
8 LINES
B-CHANNELS :
6
BCHLCNT :
4
+--------------------------------+-+------------+------------+------------

2.4. AMO-CGWB = Configuration of GateWay STMI Board/card; options:

CHANGE-ZANDE:TYPE=ALLDATA,GATEKPR=YES; /* Internal Gate Keeper for the STMI cards. /*
ADD-CGWB:LTU=1,SLOT=11,SMODE=NORMAL,IPADR=172.19.208.184,NETMASK=255.255.255.128,
PATTERN=255,DEFRT=172.19.208.129,BITRATE="100MBFD",TRPRSIP=12;
/* Had 12 SIP Trk channels/call path available at SIP Service Provider /*

CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=11,TYPE=ASC,T38FAX=YES,RFCFMOIP=YES,
RFCDTMF=YES,REDRFCTN=YES,PRIO=PRIO1,CODEC=G711U,RTP="20";
CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=11,TYPE=ASC,PRIO=PRIO2,CODEC=G711A,RTP="20";
CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=11,TYPE=ASC,PRIO=PRIO3,CODEC=G723,RTP="30";
CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=11,TYPE=ASC,PRIO=PRIO4,CODEC=G729,RTP="20";
CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=11,TYPE=ASC,PRIO=PRIO5,CODEC=G729A,RTP="20";
CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=11,TYPE=ASC,PRIO=PRIO6,CODEC=G729B,VAD=YES,RTP="20";
CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=11,TYPE=ASC,PRIO=PRIO7,CODEC=G729AB,VAD=YES,RTP="20";
/* set all possible codec types, that stmi gw can support thru..../*
/* The talk codec will be negotiated and choosed by end devices /*

CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=11,TYPE=MGNTDATA,MGNTIP=172.19.208.140,
BUSIP=172.19.208.140;
/* 172.19.208.140 = Assistant IP to upload/get STMI CARD SETTINGS from backup;
/* WHEN load/replace the CARD..../*
<DIS-CGWB:1,11;
-----------------------------------------------------------------------------| CGW BOARD DATA
|
-----------------------------------------------------------------------------|
HG3530
SIP
HG3550
|
-----------------------------------------------------------------------------| LTU = 1
SLOT = 11
SMODE = NORMAL
POOLNO: 0
|
-----------------------------------------------------------------------------GLOBAL DATA AND ETHERNET INTERFACE DATA - CONFIGURABLE VALUES:
-------------------------------------------------------------IPADR
= 172.19 .208.184
TCPP
= 4060
(4060)
=> TCP signal. Port (default=4060)
NETMASK
= 255.255.255.128
VLAN
= NO
(NO)
DEFRT
= 172.19 .208.129
(0.0.0.0 = NOT CONFIGURED)
BITRATE
= 100MBFD (AUTONEG )
VLANID = 0
(0)
PATTERN
= 255 (213)
TLSP
= 4061
(4061) => 255 = uLaw for USA, 213= A-Law
TRPRSIP
= 12 (0)
TRPRH323 = 0
(0)
=> TRPRSIP=define TRunk PRotocol SIP, 12Chann. config. (max.120).
TRPRSIPQ = 0
(0)
TPRH323A = 0
(0)
=> 12 = SIP Provider call path/Channels/ports available ...
DNSIPADR2 = 0 .0 .0 .0
SIPTLSP
= 5061 (5061)
Can set only 1 trk prot.per STMI: SIP or SIPQ or H323(XPress.)
USEWANIF = NO
(NO)
ASC DATA - CONFIGURABLE VALUES:
=> Audio Stream Control
------------------------------TOSPL
= 184
(184)
TOSSIGNL = 104
(104)
UDPPRTLO = 29100 (29100) UDPPRTHI = 30099 (30099) => UDP Voice payload Ports Low (std.=29100) + 1k = High (30099)
T38FAX
= YES
(YES)
REDRFCTN = YES
(YES) => ask provider if they comply RFC 2198 = Redundant of rfc2833 dtmf tones.
RFCFMOIP = YES
(NO)
RFCDTMF = YES
(YES)
=> RFC2833 Fax Modem and DTMF tones (RFC = Request For Comments = "norm")
PRIO1
PRIO2
PRIO3
PRIO4
PRIO5
PRIO6
PRIO7

:
:
:
:
:
:
:

CODEC
CODEC
CODEC
CODEC
CODEC
CODEC
CODEC

=
=
=
=
=
=
=

G711U
G711A
G723
G729
G729A
G729B
G729AB

VAD
VAD
VAD
VAD
VAD
VAD
VAD

=
=
=
=
=
=
=

NO
NO
NO
NO
NO
YES
YES

RTP-SIZE
RTP-SIZE
RTP-SIZE
RTP-SIZE
RTP-SIZE
RTP-SIZE
RTP-SIZE

MANAGEMENT STATION AND BACK-UP SERVER

------------------------------------MGNTIP
= 172.19.208.140 (0.0.0.0)
BUSIP
= 172.19.208.140 (0.0.0.0)

=
=
=
=
=
=
=

20
20
30
20
20
20
20

=> G711u-Law= USA/Canada/Japan = PCM24 = TDM Quantization = high Bandwidth

=> G711A = All other countries (Germany, Europe, Latin America..)= PCM30
=> G723 = barely used

=> Assistant IP address for backup/restore

2.5. INSERT the STMI card with Lan cable.

F5350 E8 N9300 IN SERV BPA
BOARD
SECONDARY IN ATTEND L
ALARM CLASS:CENTRAL:002
** :LTG1 :LTU1 :011: 0
: 0 Q2316-X10 STMI2
F5749 E8 N9301 NO ACT
BPA
BOARD
ALARM CLASS:CENTRAL:002
REASON:00H ONLY SIGNALING
MSG_HBR_WARNING

LW REQUEST

F5749 E8 N9303 NO ACT

BPA
BOARD
LW REQUEST
ALARM CLASS:CENTRAL:002
** :LTG1 :LTU1 :011: 0
: 0 Q2316-X10
REASON:00H ONLY SIGNALING
MSG_IP_LINK_RESTORE

14-06-13 11:00:04
BST:01

PLS:-08

14-06-13 11:01:15

14-06-13 11:01:16
STMI2/1

F5471 E8 N9304 IN SERV BPA

CIRCUIT L1 PORT ACTIVE
ALARM CLASS:CENTRAL:002
** :LTG1 :LTU1 :011: 0- 60: 0 Q2316-X10 STMI2/1
REASON:07H LAYER 1 ACTIVE

BST:01

PLS:-08

14-06-13 11:01:17
BST:01

PLS:-08

<DIS-BCSU:TBL,,1,11;
LTG 1 LTU 1
SRCGRP 1
ALARMNO-LTU 0
-----+-----------+--------+---+-+-+---+-+------------+------------+-----------|
|
|
|S|H|AL-| |
|
|
| ASSIGNED | MODULE |FCT|E|W|ARM| | INSERTED
|
HW| MODULE
PEN | MODULE
| TYPE
|ID |C|Y|NO | | MODULE
|STATE INFO | STATUS
-----+-----------+--------+---+-+-+---+-+------------+------------+-----------11 | Q2316-X10 STMI2
1 *
0| | Q2316-X10 | 1 -08 - | READY
+--------------------------------+-+------------+------------+-----------| IP ADDRESS : 172. 19.208.184
B-CHANNELS : 111
BCHLCNT : 98
| BLOCK NO
: 11
PRERESERVED LINES ASSIGNED :
NO
| 1. FUNCT : HG3550
2 LINES
B-CHANNELS : 60
BCHLCNT : 60
| 2. FUNCT : HG3530
51 LINES
B-CHANNELS : 45
BCHLCNT : 34
| 3. FUNCT : SIP
8 LINES
B-CHANNELS :
6
BCHLCNT :
4
+--------------------------------+-+------------+------------+------------

3. TRUNK CONFIGURATION - RMX-TDM = ISDN inSIDE STMI-GW = Switching Unit = SU = SWU....

3.1. AMO-COSSU = Class Of Service Switching Unit for the Trunk
ADD-COSSU:NEWCOS=11,INFO="Native SIP - Unify";
CHANGE-COSSU:TYPE=COS,COS=11,AVCE=TA&TNOTCR&MB&FWDNWK&TTT&FWDECA;
CHANGE-COSSU:TYPE=COS,COS=11,AFAX=TA&TNOTCR&BASIC;
CHANGE-COSSU:TYPE=COS,COS=11,ADTE=TA&TNOTCR&BASIC;
<DIS-COSSU:COS,11;
+------+-----------------+---------------+-----------------+
| COS |
VOICE
|
FAX
|
DTE
|
+------+-----------------+---------------+-----------------+
|
11 |>NATIVE SIP - UNIFY
|
|
|
TA
|
TA
|
TA
|
|
|
TNOTCR
|
TNOTCR
|
TNOTCR
|
|
|
MB
|
BASIC
|
BASIC
|
|
|
FWDNWK
|
|
|
|
|
TTT
|
|
|
|
|
FWDECA
|
|
|
+------+-----------------+---------------+-----------------+

3.2. AMO-COT = Class of Trunk for Call Processing

ADD-COT:COTNO=11,PAR=RCL&XFER&ANS&CHRT&CEBC&BSHT&BLOC&LWNC&NLCR&TSCS&DFNN&NLRD&
LINC&NOFT&IBBA&NTON;
CHANGE-COT:COTNO=11,COTTYPE=COTADD,DEV=INDEP,INFO="Native SIP - Unify";
<dis-cot:11;
COT: 11 INFO: Native SIP - Unify
DEVICE: INDEP
SOURCE: DB
PARAMETER:
RECALL IF USER HANGS UP IN CONSULTATION CALL
TRUNK CALL TRANSFER
TRUNK SIGNALING ANSWER
CHANGEOVER FROM HOLD TO RING TONE
CALL EXTEND FOR BUSY, RING OR CALL STATE
DON'T RELEASE CALL TO BUSY HUNT GROUP
END-OF-DIAL FOR BLOCK IS SET
SEND NO NODE NUMBER TO PARTNER
INCOMING CIRCUIT FROM SYSTEM WITHOUT LCR
TSC-SIGNALING FOR NETWORKWIDE FEATURES (MANDATORY)
USE DEFAULT NODE NUMBER OF LINE
INCOMING CIRCUIT FROM SYSTEM WITHOUT LCR (DATA)
LINE WITH IMPLICIT NUMBERS FOR CARRIER
NO FLAG TRACE
SEND DIGITS VIA IN.BAND DTMF BEFORE ANSWER
NO TONE

RCL
XFER
ANS
CHRT
CEBC
BSHT
BLOC
LWNC
NLCR
TSCS
DFNN
NLRD
LINC
NOFT
IBBA
NTON

3.3. AMO-COP = Class of Parameter for Device Handler.

ADD-COP:COPNO=11,PAR=L3AR,TRK=TA,TOLL=TA;
CHANGE-COP:COPNO=11,COPTYPE=COPADD,DEV=INDEP,INFO=" Native SIP - Unify";
<DIS-COP:11;
COP: 11 INFO: Native SIP - Unify
DEVICE: INDEP
SOURCE: DB
PARAMETER:
REGISTRATION OF LAYER 3 ADVISORIES

L3AR

CO TRUNK ACCESS:
TRUNK ACCESS

TA

TOLL ACCESS:
TRUNK ACCESS

TA

3.4. AMO-BUEND =

Buendel = Bundle =

Trunk Group

ADD-BUEND:TGRP=11,NAME="NATIV.SIP_UNIFY",NO=12;
/* NO=12 =>how many ports/licenses/channels/call path available at Sip Trk Provider or SIP external Device (e.g.Fax Server).
<DIS-BUEND:11;
+------------------------------- FORMAT = L -----------------------------------+
| TGRP NUMBER :
11
TGRP NAME
: NATIV.SIP_UNIFY
MAXIMUM NO.
:
12 |
|
CHARCON
: NEUTRAL
|
| SUBGROUP NO.:
1
DEVICE TYPE : TRACENO
:
0 |
| SEARCH MODE : CIRCULAR
ACD THRESHOLD :
* |
| NUMBER OF ASSOCIATED ROUTES
: 0
PRIORITY
:
0 |
| TDDRFLAG
:
ON TDDRTHRESHOLD: 0
|
| GDTRRULE
:
0
ACDPMGRP
: 0
|
+------------------------------------------------------------------------------+

3.5. AMO-TDCSU =

Trunk Digital Config. Switching Unit

ADD-TDCSU:OPT=NEW,PEN=1-1-11-0,COTNO=11,COPNO=11,LCOSV=1,LCOSD=1,COS=11,CCT="
NATIVE SIP",PROTVAR="ECMAV2",SEGMENT=8,NNO=11,TGRP=11,DEV=HG3550IP,SRCHMODE=CIR,
BCHAN=1&&12,BCGR=1; /* CHAN=channels available at SIP Provider, e.g.: 12 )
H04: AT PEN 1-01-011-0
ASSIGNED TO BCGR 1:

THE FOLLOWING B-CHANNELS HAVE BEEN NEWLY

1 && 12

F5418 E8 N9782 IN SERV BPB

CIRCUIT LX ACTIVE
ALARM CLASS:SWU-PER:001
** :LTG1 :LTU1 :011: 0
: 0 Q2316-X10
REASON:07H LAYER 1 ACTIVE (GREEN)
FORMAT:36
DEVICE NAME: HG3550IP
F5418 E8 N9783 IN SERV BPB
CIRCUIT LX ACTIVE
ALARM CLASS:SWU-PER:001
** :LTG1 :LTU1 :011: 0
: 0 Q2316-X10
REASON:09H LAYER 3 ACTIVE
FORMAT:36
DEVICE NAME: HG3550IP

14-06-13 15:44:59
STMI2/1

BST:01

PLS:-08

14-06-13 15:44:59
STMI2/1

BST:01

PLS:-08

<DIS-TDCSU:1-1-11-0;
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV
= HG3550IP
PEN
= 1-01-011-0
TGRP
= 11
|
|---------------------------------------------------------------------------|
| PROTVAR = ECMAV2
INS
= Y
SRCHMODE = CIR
| => PROTVAR <=== copy-PRODE:pvcd,16; for USA
| COTNO
= 11
COPNO
= 11
DPLN
= 0
|
| ITR
= 0
COS
= 11
LCOSV
= 1
|
| LCOSD
= 1
CCT
= NATIVE SIP
DESTNO
= 0 => if 0 zero, trk loopback is possible, but no loop detection (traccount)
| SEGMENT = 8
DEDSCC
=
DEDSVC
= NONE
|
| FACILITY =
DITIDX
=
SRTIDX
=
|
| TRTBL
= GDTR
SIDANI
= N
ATNTYP
= TIE
|
| CBMATTR = NONE
NWMUXTIM = 10
TCHARG
= N
|
| SUPPRESS = 0
DGTPR
=
CHIMAP
= N
|
| ISDNIP
=
ISDNNP
=
|
| PNPL2P
=
PNPL1P
=
PNPAC
=
|
| TRACOUNT = 31
SATCOUNT = MANY
NNO
= 11
|
| ALARMNO = 0
FIDX
= 1
CARRIER = 1
|
| ZONE
= EMPTY
COTX
= 11
FWDX
= 1
|
| DOMTYPE =
DOMAINNO =
TPROFNO =
|
| INIGHT
=
CCHDL
=
|
| UUSCCX
= 16
UUSCCY
= 8
FNIDX
= 1
|
| CLASSMRK = EC
& G711
& G729AOPT
SRCGRP
= ( )
|
| TCCID
=
SECLEVEL = SECURE
|
| HMUSIC
= 0
CALLTIM = 60
WARNTIM = 60
|
|---------------------------------------------------------------------------|
| BCNEG
= N
BCGR
= 1
LWPAR
=
|
| LWPP
= 0
LWLT
= 0
LWPS
= 0
|
| LWR1
= 0
LWR2
= 0
|
| DMCALLWD = N
VNNO
=
|
| SVCDOM
=
|
| BCHAN
= 1 && 12
=> 12 available call path at SIP Provider
|
+---------------------------------------------------------------------------+
AMOUNT OF B-CHANNELS IN THIS DISPLAY-OUTPUT: 12

4. Routing.
AMO-WABE = WAhl BEwertung = Dialed Digit Translation, No -> Dial PLan Number = stn. or feature
AMO-RICHT = Richtung = Direction = Route number, Buend/Trk Group, Destination Number (No).
AMO-LODR = LCR (Least Coust Routing) OutDial Rules.
AMO-LDAT = Lcr DATa = richt + lodr + attributes + cot index number for outgoing calls.
amo-lprof = lcr profiles for ipda/source group (not used here for simplicity)
AMO-LDPLN = Lcr Dial PLaN = wabe -> outgoing lcr routing.

!! Since V4 Native Sip Trunk is recommended to use Profiles ( only one IP destination ) due to security reasons ;
the usage of amo-GKREG IP destinations addr. used on V3 is and still supported by GVS;
see details on item 4.4.Routing with GKREG !!!

GKREG:number, ip destin.; + LDAT: destin. GW1=GKREG_number; same as used for SIPQ .....

4.1. Open Number Routing:

LCR with TIE Access Code + hear "external" Dial Tone (W) + SIP Provider number (Z) + #
e.g.: Dial 82 + SIP vendor stn. number + # (end of dial).
ADD-RICHT:MODE=LRTENEW,LRTE=82,LSVC=VCE,NAME="NATIVE SIP ",TGRP=11,DNNO=82,
DTMFCNV=FIX,DTMFPULS=PP300,DESTNO=82,PDNNO=82;
<DIS-RICHT:LRTE,82;
+-----------------------------------------------------------------+
| LRTE = 82
NAME = NATIVE SIP
(NEUTRAL) LSVC = VCE
|
| DNNO =
82 PDNNO =
82 DESTNO = 82
|
| ROUTOPT = NO
REROUT = YES
PLB = YES
FWDBL = NO
|
| DTMFCNV = FIX
DTMFDSP = WITHOUT DTMFTEXT =
|
| DTMFPULS = PP300 BUGS = LIN ROUTATT = NO
MAINGRP =
37 |
| EMCYRTT = NO
CONFTONE = NO
RERINGRP = NO
RTENO =
37 |
| INFO =
|
| NOPRCFWD = NO
|
| NITO = NO
|
| CLNAMEDL = NO
|
| FWDSWTCH = NO
|
| LINFEMER = NO
|
| NOINTRTE = NO
|
| CSTAONS = NO
|
+-----------------------------------------------------------------+
| TGRP = 11 LDAT NATIV.SIP_UNIFY
(NEUTRAL) SUBGROUP =
1 |
+-----------------------------------------------------------------+

ADD-LODR:ODR=12,CMD=ECHO,FIELD=3;
ADD-LODR:ODR=12,CMD=END;
ADD-LODR:ODR=12,INFO="SIP TRK ACC.CODE";
<DIS-LODR:12;
+-------------------------------------------------------+
| ODR
POSITION CMD
PARAMETER
|
+--------+----------------------------------------------+
|
12
|
1
ECHO
3
|
|
|
2
END
|
+--------+----------------------------------------------+
|INFO:SIP TRK ACC.CODE
|
+-------------------------------------------------------+

=> LDPLN 82-W-Z

=ECHO field 3 = ECHO Z = Send out only Z
=> Field 1= 82 Tie; Field 2= W; Field 3 = Z = any number/quantity

ADD-LDAT:LROUTE=82,LSVC=VCE,LVAL=1,TGRP=11,ODR=12,LAUTH=1,LATTR=WCHREG&PUBNUM,
COTIDX=11;
<DIS-LDAT:LCR,82;
+------------------------------------------------------------------------------+
| LROUTE = 82
LDPLN
NAME = NATIVE SIP
SERVICE = VCE |
| TYPE = LCR
DNNO OF ROUTE =
82
|
+------+-----+-----+----+-----+----------+-----------+----------+------+-------+
|
|
|
|
|
| SCHEDULE | CARRIER
|
|
|
|
|LRTEL | LVAL|TGRP | ODR|LAUTH| ABCDEFGH |
ZONE|
LATTR | LDSRT|COTIDX |
+------+-----+-----+----+-----+----------+-----------+----------+------+-------+
|
1|
1|
11| 12| 1
| ******** | 1
EMPTY|
WCHREG |
| 11
| => With CHarge REGistration (CDR)
|
|
|
|
|
PUBNUM | => PUBlic NUMber = calling #, from SDAT (e.g.: 972.756.0123).
+------------------------------------------------------------------------------+

ADD-WABE:CD=82,DAR=TIE;
<DIS-WABE:GEN,82;
-----------------------------------------------------------------------------| DIGIT INTERPRETATION
VALID FOR ALL DIAL PLANS
|
-----------------------------------------------------------------------------|
|
CALL PROGRESS STATE
|NODE/DIGIT| RESERVED/CONVERT |
|
CODE
|
1 11111 11112 22| ANALYSIS | DNI/ADD-INFO
|
|
|0 12345 67890 12345 67890 12| RESULT | *=OWN NODE
|
-----------------------------------------------------------------------------| 82
|. .**** ***** **... ..... .*| TIE
|
|
------------------------------------------------------------------------------

ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP="82"-"W"-"Z",DPLN=0,LROUTE=82,LAUTH=1;
<DIS-LDPLN:CD,82;
+----------------------------------------------------------+
| CD
82
--->
|
+--------+-------------------------------------+------------+
| LDPNO | LDP
| DIPLNUM
|
+--------+-------------------------------------+------------+
|
41 | 82-W-Z
|
0
|
+-------+--------------------------------------------------+
<DIS-LDPLN:LDP,,41;
+--------------+-------------------------------------------------+
| DIPLNUM:
0|
|
| LDPNO :41
| LDP : 82-W-Z
|
|
| SPC : 22
|
|
| FDSFIELD : 0
SDSFIELD : 0
PINDP : N
|
+------+-------+-------------------------------------------------+
| DPLN | LROUTE| LAUTH
|
|------+-------+-------------------------------------------------+
|
0 |
82 | 1
|
+------+-------+-------------------------------------------------+

/* If SIP vendor has fixed numbers, e.g. 7170 to 7199, you can replace the Z by XXXX (4X not 2X)...

4.2. Closed Number Routing ( Network LCR ) :

LCR outbound (outgoing) Native Sip with # Closed Number Plan #
Dial Sip Vendor Devices (e.g. numbers 7170 to 7199) directly...
ADD-WABE:CD=83,DAR=NETRTE,CHECK=N;
<DIS-WABE:GEN,83;
-----------------------------------------------------------------------------| DIGIT INTERPRETATION
VALID FOR ALL DIAL PLANS
|
-----------------------------------------------------------------------------|
|
CALL PROGRESS STATE
|NODE/DIGIT| RESERVED/CONVERT |
|
CODE
|
1 11111 11112 22| ANALYSIS | DNI/ADD-INFO
|
|
|0 12345 67890 12345 67890 12| RESULT | *=OWN NODE
|
-----------------------------------------------------------------------------| 83
|* ..... ..... ..... ..... ..| NETRTE
|
|
------------------------------------------------------------------------------

ADD-RICHT:MODE=CD,LRTE=83,CD=83,CPS=0,SVC=vce,NAME="N.SIP CLOS#
DESTNO=83,DNNO=83,PDNNO=83;

",TGRP1=11,

<DIS-RICHT:CD,83;
+------------------------------------------------------------------------------+
| ROUTES FOR ALL DPLN
SVC = VCE |
|
|
+-------+------------------+----+-+------------------------------+-----+----+--+
|CODE
|NAME, CQMAX,
|TGRP|P|
DTMF
| LRTE|CPAR| F|
|
|DESTNO AND CPS
|CCNO|L+---+---+----------------+-----+
|
| W|
|
|
1 111112|
|B|CNV|DSP|
TEXT
|PULS |
|
| D|
|
|12345 67890 123452|
| |
|
|
|PAUSE|
|
| B|
+-------+------------------+----+-+---+---+----------------------+-----+----+--+
|83
|..... ..... ......| 11| | W | W |
|
|
83|
| |
|NEUTRAL|N.SIP CLOS#
|
| |
|
|
|
|
|
| |
|
|DNNO:
83 |
| |
|
|
|
|
|
| |
|
|PDNNO:
83 |
| |
|
|
|
|
|
| |
|
|DESTNO
:83
|
| |
|
|
|
|
|
| |
|
|REROUT
:YES
|
| |
|
|
|
|
|
| |
+-------+------------------+----+-+---+---+----------------+-----+-----+----+--+

ADD-LODR:ODR=83,CMD=ECHOALL;
ADD-LODR:ODR=83,CMD=END;
ADD-LODR:ODR=83,INFO="NATIVE SIP CLOSED #";
<DIS-LODR:83;
+-------------------------------------------------------+
| ODR
POSITION CMD
PARAMETER
|
+--------+----------------------------------------------+
|
83
|
1
ECHOALL
|
|
|
2
END
|
+--------+----------------------------------------------+
|INFO:NATIVE SIP CLOSED #
|
+-------------------------------------------------------+

ADD-LDAT:LROUTE=83,LSVC=vce,LVAL=1,TGRP=11,ODR=83,LAUTH=1,LATTR=WCHREG,COTIDX=11;
<DIS-LDAT:NWLCR,83;
+------------------------------------------------------------------------------+
| LROUTE = 83
NAME = N.SIP CLOS#
SERVICE = VCE |
| TYPE = NWLCR
DNNO OF ROUTE =
83
|
| SERVICE INFO =
|
+------+-----+-----+----+-----+----------+-----------+----------+------+-------+
|
|
|
|
|
| SCHEDULE | CARRIER
|
|
|
|
|LRTEL | LVAL|TGRP | ODR|LAUTH| ABCDEFGH |
ZONE|
LATTR | LDSRT|COTIDX |
+------+-----+-----+----+-----+----------+-----------+----------+------+-------+
|
1|
1|
11| 83| 1
| ******** | 1
EMPTY|
WCHREG |
| 11
|
+------------------------------------------------------------------------------+

ADD-WABE:CD=7170&&7199,DAR=Stn; /* if other side change/add #s, must done also here /*

CHANGE-WABE:CD=7170&&7199,DESTNO=83;
<DIS-WABE:GEN,,,,STN;
-----------------------------------------------------------------------------| DIGIT INTERPRETATION
VALID FOR ALL DIAL PLANS
|
-----------------------------------------------------------------------------|
|
CALL PROGRESS STATE
|NODE/DIGIT| RESERVED/CONVERT |
|
CODE
|
1 11111 11112 22| ANALYSIS | DNI/ADD-INFO
|
|
|0 12345 67890 12345 67890 12| RESULT | *=OWN NODE
|
-----------------------------------------------------------------------------| 7170 - 7199
|. .**** ***** **... ..... .*| STN
|
|
|
|
|
|DESTNO 83
|
|
|
|
|DNNO
0- 0- 83 |
|
|
|
|PDNNO
0- 0- 83 |
------------------------------------------------------------------------------

/* The routing 4.1 Open # and 4.2 Closed # and 4.3 One # can be configured together; works as separated routes.../*

4.3. One Number Routing Access:

LCR outbound (outgoing) Sip with one fixed Number e.g.: dial 811 to connect.
ADD-RICHT:MODE=LRTENEW,LRTE=811,LSVC=VCE,NAME="XP AUDIO CONF. ",TGRP=11,DNNO=11,
DTMFCNV=FIX,DTMFPULS=PP300,DESTNO=11,PDNNO=11,COTIDX=11;
<DIS-RICHT:LRTE,811;
+-----------------------------------------------------------------+
| LRTE = 811
NAME = XP AUDIO CONF.
(NEUTRAL) LSVC = VCE
|
| DNNO =
11 PDNNO =
11 DESTNO = 11
|
| ROUTOPT = NO
REROUT = YES
PLB = YES
FWDBL = NO
|
| DTMFCNV = FIX
DTMFDSP = WITHOUT DTMFTEXT =
|
| DTMFPULS = PP300 BUGS = LIN ROUTATT = YES
MAINGRP =
30 |
| EMCYRTT = NO
CONFTONE = NO
RERINGRP = NO
RTENO =
30 |
+-----------------------------------------------------------------+
| TGRP = 11 LDAT XP AUDIO CONF.
(NEUTRAL) SUBGROUP =
35 |
+-----------------------------------------------------------------+

ADD-LODR:ODR=90,CMD=ECHO,FIELD=1;
ADD-LODR:ODR=90,CMD=NPI,NPI=UNKNOWN,TON=UNKNOWN;
ADD-LODR:ODR=90,CMD=END;
ADD-LODR:ODR=90,INFO="XPRESSION IP";
<DIS-LODR:90;
+-------------------------------------------------------+
| ODR
POSITION CMD
PARAMETER
|
+--------+----------------------------------------------+
|
90
|
1
ECHO
1
|
|
|
2
NPI
UNKNOWN
|
|
|
3
TON
UNKNOWN
|
|
|
4
END
|
+--------+----------------------------------------------+
|INFO:XPRESSION IP
|
+-------------------------------------------------------+

ADD-LDAT:LROUTE=811,LSVC=VCE,LVAL=1,TGRP=11,ODR=90,LAUTH=1,LATTR=PUBNUM,DNNO=11;
<dis-ldat:lcr,811;
+------------------------------------------------------------------------------+
| LROUTE = 811
LDPLN
NAME = XP AUDIO CONF.
SERVICE = VCE |
| TYPE = LCR
DNNO OF ROUTE =
11
|
| SERVICE INFO =
|
+------+-----+-----+----+-----+----------+-----------+----------+------+-------+
|
|
|
|
|
| SCHEDULE | CARRIER
|
|
|
|
|LRTEL | LVAL|TGRP | ODR|LAUTH| ABCDEFGH |
ZONE|
LATTR | LDSRT|COTIDX |
+------+-----+-----+----+-----+----------+-----------+----------+------+-------+
|
1|
1|
11| 90| 1
| ******** | 1
EMPTY|
PUBNUM |
| 11
|
|
| DNNO =
11
|
+------------------------------------------------------------------------------+

ADD-WABE:CD=811,DAR=TIE,CHECK=N;
<DIS-WABE:GEN,811;
-----------------------------------------------------------------------------|
|
CALL PROGRESS STATE
|NODE/DIGIT| RESERVED/CONVERT |
|
CODE
|
1 11111 11112 22| ANALYSIS | DNI/ADD-INFO
|
|
|0 12345 67890 12345 67890 12| RESULT | *=OWN NODE
|
-----------------------------------------------------------------------------| 811
|. .**** ***** **... ..... .*| TIE
|
|
------------------------------------------------------------------------------

ADD-LDPLN:LCRCONF=LCRPATT,DIPLNUM=0,LDP="811",LROUTE=811,LAUTH=1;
<DIS-LDPLN:CD,811;
+-------+-------------------------------------+------------+
| LDPNO | LDP
| DIPLNUM
|
+-------+-------------------------------------+------------+
|
33 | 811
|
0
|
+-------+--------------------------------------------------+
<DIS-LDPLN:LDP,0,33;
+--------------+-------------------------------------------------+
| LDPNO :
33| LDP : 811
|
|
| SPC : 22
|
|
| FDSFIELD : 0
SDSFIELD : 0
PINDP : N
|
+------+-------+-------------------------------------------------+
| DPLN | LROUTE| LAUTH
|
|------+-------+-------------------------------------------------+
|
0 |
811 | 1
|
|
1 |
811 | 1
|

4.4. Routing with GKREG; one STMI multiple IP destinations.

- Customers migrating from early versions using only one STMI with multiple sIP destinations can still use this GKREG feature;
- This is and still fully supported by Development/GVS; they recommend using profiles for security reasons i.e. without them, the SIP board
can affectively be addressed from any IP.
The SIP Profile usage had the disavantage of allow only one SIP far end destination.

4.4.1. Additional amo changes:

CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=11,TYPE=LEGKDATA,GWNO=11,REGEXTGK=NO;
ADD-GKREG:GWNO=11,GWATTR=INTGW&HG3550V2&SIP,DIPLNUM=0,DPLN=0,LAUTH=1 INFO="STMI LTU1 SLOT11
INTERNAL REG. NAT.SIP NO PROFILE";;
/* Tells to use Internal GateKeeper REGistration.../*
ADD-GKREG:GWNO=811,GWATTR=EXTGW&HG3550V2&SIP,GWIPADDR=172.19.208.158,
GWDIRNO=811,DIPLNUM=0,DPLN=0,LAUTH=1,INFO="XP_AUDIO_CONFERENCE_NO_SIP_PROFILE";
/* SIP Provider/Vendor/Device IP destination e.g.: 172.19.208.158
/*
<DIS-CGWB:1,11,LEGKDATA;
-----------------GWNO
= 11 (0)
GWDIRNO
=
REGEXTGK = NO (NO)
<DIS-GKREG:11&811;
+-----------------------------------------------------------------------------+
| GWNO
11
GWATTR
INTGW
HG3550V2 SIP
|
| GWIPADDR 172.19 .208.184
GWDIRNO
|
| DIPLNUM 0
DPLN 0
|
| LAUTH
1
|
| GATEWAY REGISTERED: NO
|
| IP GATEWAY IS CONFIGURED
BY GKREG
|
| INFO:
STMI LTU1 SLOT11 INTERNAL REG. NAT.SIP NO PROFILE
|
| SECLEVEL: TRADITIO
|
+-----------------------------------------------------------------------------+
| GWNO
811
GWATTR
EXTGW
HG3550V2 SIP
|
| GWIPADDR 172.19 .208.158
GWDIRNO 811
|
| DIPLNUM 0
DPLN 0
|
| LAUTH
1
|
| GATEWAY REGISTERED: NO
|
| IP GATEWAY IS CONFIGURED
BY GKREG
|
| INFO:
XP_AUDIO_CONFERENCE_NO_SIP_PROFILE
|
| SECLEVEL: TRADITIO
|
+-----------------------------------------------------------------------------

You can use any routing type ( 4.1 and/or 4.2 and/or 4.3 ) adding on LDAT: GW1=...
Example below using Route 4.2. Closed Number:
CHA-LDAT:LROUTE=83,LSVC=VCE,LRTEL=1,GW1=811-0;
<DIS-LDAT:NWLCR,83;
+------------------------------------------------------------------------------+
| LROUTE = 83
NAME = N.SIP CLOS#
SERVICE = VCE |
| TYPE = NWLCR
DNNO OF ROUTE =
83
|
| SERVICE INFO =
|
+------+-----+-----+----+-----+----------+-----------+----------+------+-------+
|
|
|
|
|
| SCHEDULE | CARRIER
|
|
|
|
|LRTEL | LVAL|TGRP | ODR|LAUTH| ABCDEFGH |
ZONE|
LATTR | LDSRT|COTIDX |
+------+-----+-----+----+-----+----------+-----------+----------+------+-------+
|
1|
1|
11| 83| 1
| ******** | 1
EMPTY|
WCHREG |
| 11
|
|
+-----------------------------------------------------------------------+
|
|
GW1 = 811-0
GW2 =
GW3 =
|
|
|
GW4 =
GW5 =
=> GW2 to 5 = alternate failover IP destination route (if GW1 broke, goes to GW2 ).
+------------------------------------------------------------------------------+

The TDCSU: Protocol, Segment 2 (of 8) + LDAT GW/GKREG will send to the SIP GW a SETUP with Info Element:
IE:

(56) : (1C)

QSIG facility
9F AA 06 80 01 00 82 01 00 8B 01 00 A1 2A 02 02
14 82 06 08 2B 0C 02 88 53 02 01 64 30 1A 30 0C
Networking Extension
Network Facility Extensions
InvokeComp - ID: 1482
Component type: Global value
Operation: Nq24TargetGateways
(100)
targetList
Gateway Addr: 172.19.208.158 Port: 5060

/* If need to delete the ldat lcr gkreg gw entry /*

<del-ldat: KIND = lrtel, LROUTE = 83, LSVC = vce, LRTEL = 1, GWIDX = ??
GWIDX
: GATEWAY INDEX TO DELETE
POSSIBLE VALUES : 1-5
GWIDX = 1;

DEL-LDAT:LRTEL,83,VCE,1,1;

For another Vendor IP Routing address using the same STMI, create another external GKREG (e.g. 812) and LCR.

4.4.2. SIP GW WBM change for STMI - Native SIP + GKREG:

WBM => Explorers -> Voice Gateway -> SIP Trunk Profiles Parameter:
Uncheck the field " Use Profiles for Trunks via Native SIP: "
Apply => Save clicking on botton diskett icon =>
=> Reboot clicking on circular arrow icon next to diskett ( see details on botton on figure of item 5.1 )

For the next item 5, SIP with Profiles (no GKREG item 4.4) leave the field checked...

4.5. Miscelaneous AMO's system configuration for USA:

CHANGE-CTIME:TYPESWU=CP2,GWNAVAIL=10;

/* GW Not AVAILable; 10 seconds configured, std =60 sec.

/* blocktime if far ip is temporary out => F4066
F4066 M8 N0100 NO ACT
BPA
CP
ADVISORY
14-04-16 15:58:40
ALARM CLASS:CENTRAL:023
CC:15362 EC: 2017 UA:B2C8:4E91 SP:B764:143C LD:01-11-001-000
DT:6C ST:6F SN:
0 CEVT:CD CSEV: F CST:15
Cha-ZAND:type=ALLDATA,CNTRYCD=K,SIUANN=D; /*=> for US slma, siu announcement
CHANGE-ZAND:TYPE=ALLDATA,HOLDTN=RA, ANATESIG=RA; /* music on hold options
CHANGE-ZAND:TYPE=ALLDATA,TRANSFER=EXTEND, EXCOCO=YES; /* transfer CO to CO calls
CHANGE-ZAND:TYPE=ALLDATA2,USRINGTY="K";
CHANGE-ZAND:TYPE=ALLDATA2,LNR=YES,CAMPON=YES;
CHANGE-ZAND:TYPE=CONFC,CODE=ULAW,CONFAT=3,STNAT=3; /*=> PCM24 uLaw.
CHANGE-ZAND:TYPE=TN,SIUC="0K",DTR="0K",RDS="0K",CONFC="K"; /*=> US Tones
CHANGE-ZAND:TYPE=TONES,CP=HOLDLINE,SIU="22"; /* internal Mozart music
ACT-TREF:K; /* US Attenuation table
COPY-PRODE:PVCD,16; /*=> US Trunk Protocols.
CHANGE-ZAND:TYPE=OPTLOAD; /*=> Phone Protocols.
CHANGE-ZAND:TYPE=ALLDATA2,TEXTSEL=AMERICAN&GERMAN&BRAZIL&SPANISH&ENGLISH;
CHA-ZAND:TYPE=OPTISET,DISPLOGO="
UniFy-OS4k V7R1";
CHANGE-ZAND:TYPE=OPTISET,DISPTIME="12HOUR",ACOUSTID=USA,LANGID=ENGLISH&GERMAN&PORTUG&SPANISH; /* => for US digit.phones

10

4.6.WAYS TO CONVERT incoming DID NUMBERS:

W.1. DIDCR => TDCSU: TRTBL = didcr
Example: External called 972.550-7150; Telco sends 4 digits 7150 to TDCSU....
Numbers to convert to Stations (87150 and 27010/37500)
7150 => 87150
7170 ==>27010
7180 ==>37500
DIDCR needs to receive 4 digits (7150) delete 1 (7) = 150
Take 15 and transforms to 8715 and use the last "0"; will cover stn 87150 to 87159...
CHANGE-DIDCR:TYPE=SRT,SRTABLE=4,NETSVC=NONE,RULEIDX=6; /*tdcsu:DEDSVC=NONE, SRTIDX=4
DIS-DIDCR:SRT;
PRI SERVICE RULE TABLE SRTABLE=4
NETWORK SERVICE
RULEIDX
------------------------FX
0
INTLWATS
0
INWATS
0
LDS
0
NONE
6
PPC900
0
SDS
0
TTA
0
VPN
0
ADD-DIDCR:RULEIDX=6,TOTDIG=4,DELDIG=1;
CHANGE-DIDCR:TYPE=DID,RULEIDX=6,TBLIDX=15,DIGITS=8715;
CHANGE-DIDCR:TYPE=DID,RULEIDX=6,TBLIDX=17,DIGITS=2701;
CHANGE-DIDCR:TYPE=DID,RULEIDX=6,TBLIDX=18,DIGITS=3750;
DIS-DIDCR:RULETBL,6;
-----------------------------------------------------DID DIGIT CONVERSION TABLE RULEIDX= 6
------------------------------------------------------TOTAL NUMBER OF EXPECTED INCOMING DIGITS: 4
NUMBER OF DIGITS TO BE DELETED:
1
TBL_
TBL_
TBL_
TBL_
TBL_
IDX DIGITS
IDX
DIGITS
IDX
DIGITS
IDX
DIGITS
IDX DIGITS
------------------------------------------------------------------------------00
20
40
60
80
01
21
41
61
81
02
22
42
62
82
11
31
51
71 871
91
12
32
52
72
92
13
33
53
73
93
14
34
54
74
94
15 8715
35
55
75
95
16
36
56
76
96
17 2701
37
57
77
97
18 3750
38
58
78
98
19
39
59
79
99
------------------------------------------------------------------------------/* If the convertion is only for 71xx to 871xx then:
/*
DIDCR receives 4 digits (71xx; Number of Digts to be Deleted: 0 (zero)
/*
Take TBL_IDX 71 and transforms to DIGITS 871; will cover stns. 87100 to 87199...
==========================================================================================

W.2.TDCSU:

TRTBL = GDTR
What Telco sends will be accept.
Can be manipulated further with TDCSU: SUPPRESS and/or

DGTPR

or RUFUM

W.3. RUFUM

(SYSTEM Wide for TRTBL=GDTR to all DID trunk types)..

<DIS-TDCSU:1-81-2-0;
+------------------------ DIGITAL TRUNK (FORMAT=L) -------------------------+
| DEV
= S1COD
PEN
= 1-81-002-0
TGRP
= 92
|
|---------------------------------------------------------------------------|
| PROTVAR = NI2
INS
= Y
SRCHMODE = DSC
|
| TRTBL
= GDTR
SIDANI
= N
ATNTYP
= CO
|
| SUPPRESS = 0
DGTPR
=
|

External caller dialed 972.550-7150

Telco PRI T1 NI2 will sent only 4 digits to TDCSU
7150
HiPath4000 has physical station 87150. The number 7150 must be assigned as stn on WABE.
The conv.code (destination) can be another stn.# with not correlated number (e.g.:38492)
ADD-RUFUM:TYPE=DID,DID1=7150,DID2=87150;
<DIS-RUFUM;

+-----------+-----------------------------+--------------+
|
TYPE
|
DIALLED CODE
| CONV. CODE
|
+-----------+-----------------------------+--------------+
|
DID |
7150
|
87150 |

W.4. Insert # on TDCSU: DGTPR=8 SUPRESS=0

CHA-TDCSU:PEN=1-81-2-0,DGTPR=8;
External caller dialed 972.550-7157
Telco PRI T1 NI2 will sent to TDCSU
7157
TDCSU will add 8 in front of 7157 to call the physical station 87157.
TO DELETE THE TDCSU:DGTPR;

USE

CHA-TDCSU: PEN=X-Y-Z-W, DGTPR= * ;

/* ONE STAR "*" to the hell

11

5. VoIP = SIP GW.

Web Browser Management (WBM) Settings; inside STMI card.

5.1. Activation of SIP Trunk Profile GW:
Open OS4k - Assistant -> Expert Mode -> Gateway Dashboard -> HG35xx Web Base Management (WBM)
on WBM, update board list and connect to the STMI card (example: PEN = 1-1-11)
WBM => Explorers -> Voice Gateway -> SIP Trunk Profiles
(Choose one that is appropriate for the Sip Vendor/Provider connection..) =>
right mouse click on e.g. NativeTrunkWithoutRegistration -> Enter the Native SIP IP address of the destination
provider/vendor/device on Proxy (e.g.: 172.19.208.158);
then scroll down on the page and click the Apply button.
Then again; right mouse click on NatTrkWithoutRegistration -> Activate

Folder; turns green =>

Ask SIP Provider/Vendor which transport protocol is using (TCP or UPD)...

Check below fields always, after card replaced !!!!

Unlocked for
write access !

Finally Click on Diskette icon to save it....

||
running lw pzksti40.A1.....

Continuation of SIP Trunk Profiles List on V7R0 lw pzksti40.A1.002-008 at STMI card:

12

For virtual STMI (vSTMI ) running on SoftGate (SG lw pzksgw50.A1.007-007) there are 3 more profiles choices:
+ Microsoft - Lync
+ Microsoft - OCS
+ XPressions => (native Sip, but this connection lose the display messages from XP)
- The list can be different with less or more providers in old or future lw version;
do always consult / display the running STMI with WBM => Explorers -> Voice Gateway -> SIP Trunk Profiles ...

From GVS Hot Issue Notif. #31

June-2015:

Item 9. Correct HG3500 SIP Trunk Profile to be used for 3rd Party Applications
There is a common misunderstanding with the usage of SIP Trunk Profiles used on the HG3500 and vHG3500 boards. When no specific named
profile exists for 3rd Party Applications (not to be confused with SIP Service Provider), meaning the application is not explicitly certified, then the
best profile to use is NatTrkEnterprise. NatTrkEnterprise as per the WBM Profiles Details is described as Recommended Profile for 3rd Party
SIP Applications using REFER.
This profile is often confused with either NatTrkWithRegistration or NatTrkWithoutRegistration which were intended for SIP Service Providers.
Certification for SIP service providers is still a mandatory requirement as per official Sales Information literature. Moreover please be aware the
current released SIP Service Provider list is linked from Release Notes and can be found under INF-13-000534.

Ping the far end:

13

5.2. Other possible SIP GW settings :

Figure 5.2.1

Figure 5.2.2

14

WBM=> Explorers -> Payload => right mouse click on HW Modules

Figure 5.2.3

DTMF Outband Sign.= only for H323 connection (e.g. XPressions); not for SIP (RFC2833 or inband)

Figure 5.2.4

Figure 5.2.5

15

Figure 5.2.6

Figure 5.2.7

Figure 5.2.8

Figure 5.2.9

16

6. TROUBLESHOTING:
Stn. <===> OS4k /HP4k -- rmx/tdm -- STMI/SIP-GW <=== VoIP Lan Network ===> SIP Provider/Vendor
172.19.208.184
172.19.208.158

6.1. Wireshark ( Network Sniffer Trace) on VoIP Lan Network; first most efficient break point.
Mirror the STMI Lan Network port, on L2 Switch and use Wireshark to
Capture -> Interfaces -> select the PC Lan interface port -=> Start
do ping from STMI to see if you're capturing frames; if so then
make test call from a Stn. (e.g. stn.7150 dialing 811, routing 4.3. used ) towards SIP Provider and stop capture (red square)
- Choose Filter " ip.addr==172.19.208.184 " --> Apply
Another good Filter " SIP " --> Apply
- If Invite goes out, OS4k / STMI looks ok.
- If you don't see the answer from Destination IP.158, contact the SIP Vendor/Provider IP.
- If you don't see the Invite going out; then it's OS4k internal problem on rmx or stmi gw...

For details, right click on - Session Initiation Protocol (INVITE), on above midle window => select Expand Subtrees

If you select on top main menu: Telephony --> VoIP Calls => display all calls on a capture file
Highlight one or all call and click Flow
If want to hear G711 conversation, click Player (listen discretion advised)

17

Wireshark, Native Sip with TCP as signaling transport protocol (instead upd).

Example below shows a test call from Stn. 7152 called, talked (RTP G711) to 811 Native Sip connection.
Note that the SIP Provider does the signalling on IP 172.19.208.158 and the Media Server (audio) is going on IP .174

- Wireshark SW can be download at http://www.wireshark.org/download.html

it's free :-)

- Incoming sip call, all channels busy = sip message 503 Service Not Available. (see item 7. Message conversion)
- Outgoing call, all channels busy = station get "Please Try Later".

18

6.2. RTDS, internal TDCSU ISDN trace; Second Break Point.

Assistant -> Diagnostics -> Switch Diagnosis System -> Real Time Diagnosis System =>
Click on Monitor Trunk / ISDN Trace
Choose the TDCSU pen, Type=ISDN Tracer and Start

Login with any charachter...

Click on ISDN Trace Display and make a test call (e.g.: stn.7166 dialing 811)
If setup is going out, then rmx/amos are ok.... If not check stn. trk config. and do a rmx-trace, item 6.4.
If setup is going out, but disconnect comes right after, seems a sip gw problem; do a stmi-gw trace item 6.5.

Click on Message Type, e.g. SETUP:

19

6.3. Maintenance AMO commands:

/* Status Display in Switching Unit /*
<DIS-SDSU:ALL,,PEN,PER3,,1,11;
LTG1 (PERIPHERY)
-----MOUNTING LOCATION
MODULE NAME
BDL BD(#=ACT) STATUS
------------------- LTG
1 --------------------- READY
-AP370013-----SG 1 LTU
1 --------------------- READY
** .LTG 1.LTU 1.011 STMI2
Q2316-X10 READY
LAN CONN.
. . . . . . . . . READY
=> PEN LTG=1- LTU=1- SLOT=11
NO PKI CERTIFICATE AVAILABLE
LINK SIGNAL ETHERNET . . . .
PRESENT
LAN SPEED
. . . . . . . . . 100 MBIT/S
LAN INTERFACE . . . . . . . . FDX (FULL DUPLEX)
=> Lan connection is running 100 MBFD...
CCT
FUNCTION BLOCK
0
- 1
HG3550_2
2
- 52
HG3530_2
53 - 60
HG3540_2
CCT LINE
STNO SI BUS TYPE
000 2160
PP NW
READY
=> Circuit 0 of TDCSU pen 1-1-11-0
MULTLINE 30 . . . . . . . . . . . . . .READY
000 NO CONN
001 NETWORK SUBUNIT . TMD CONN ISDN
READY
(ALT_ROUT: N)
(HG3550IP)
LINE: 2160 STNO:
SI:
001 . . . . . . . . TMD CONN ISDN READY
002 NETWORK SUBUNIT . TMD CONN ISDN

=> Channel 1 = OK

READY/BUSY/CP
CPH

=> Channel 2 in talk state

(ALT_ROUT: N)
(HG3550IP)
LINE: 2160 STNO:
SI:
001 . . . . . . . . TMD CONN ISDN READY/BUSY
------------------------------------------------------------------------

/* Realtime Trunk Group Occupation /*

<dis-buend
TGRP = 11
FORMAT = ?
: FORMAT OF OUTPUT
CHARACTERISTIC : OPTIONAL
POSS. VALUES : S
SHORT (NUMBER AND NAME)
M
MEDIUM (ALL DATA IN COMPACT FORMAT)
L
LONG (ALL DATA)
B
BCHANNEL SUMMARY (READY/BUSY/LOCKED)
FORMAT = b;

DIS-BUEND:11,B;
NO.
11

MAX
10

ACT
10

BUSY
3

FREE
7

OTHER
0

/* Reset Device Service BChannel /*

<res-dssu
TYPE = ?
: TYPE OF FUNCTION
CHARACTERISTIC : REQUIRED
CONDITIONAL
POSS. VALUES : BCHAN
B-CHANNEL
STNO
STATION NUMBER
PEN
PORT EQUIPMENT NUMBER FOR TRUNK, LINE, CIRCUIT
TYPE = bchan
PEN1 = 1-1-11-0
BCHL = ?
: B-CHANNEL NUMBER
CHARACTERISTIC : OPTIONAL
POSSIBLE VALUES : 1-30
BCHL = 1&&30;

RES-DSSU:BCHAN,1-1-11-0,1&&30;
/* Reset Device Trk (tdcsu pen) /*
<RES-DSSU:pen,1-1-11-0,
PEN2 =
/*if you choose pen2, the restart will be done on all trks between the range of pen1 and pen2 !!!/*

RES-DSSU:PEN,1-1-11-0,;

/* Reset the Board (card) Service/*

<res-bssu
ADDRTYPE = ?
: TYPE OF BOARD ADDRESSING
CHARACTERISTIC : REQUIRED
CONDITIONAL
POSS. VALUES : PEN
PHYSICAL BOARD/MODULE ADDRESS
PARTNO
BOARD/MODULE PART NUMBER
ALL
ALL BOARDS/MODULES
ADDRTYPE = pen
LTG = 1
LTU = 1
SLOT = 11;

RES-BSSU:PEN,1,1,11;
/* RMX Switching Unit Reset /*
<exec-rest:unit, bp, .......; => soft, hard or reload...

20

Realtime GW ports occupation (e.g. 3 calls):

6.4. RMX - Traces: - Do it if you don't see the Setup going out or the RTDS is temporary not working.
This covers stn. to trk messages (rmx & isdn) until the SIP GateWay.
cha-diags:comp=cp,s14=on;
ex-tracs:bp;
res,all;
flagtr,off;
selmsg,pp,g1,cd1,ev,ba&97&74; /* Standard PP networking
selmsg,pp,g1,cd2,byte,15,08;
msglen,pp,g1,280;
selmsg,pp,g2,all; /* All other PP messages
msglen,pp,g2,32;
selmsg,cp,g2,all; /* All other CP messages
msglen,cp,g2,48;
selmsg,rcv,g1,cd1,dest,40; /* FA TASK
selmsg,rcv,g1,cd2,src,40,ne;
on,hd,:diag:<filename>,30,y,y; /* <filename> = e.g. nsip1
/* do the test call
off;

Utilize ComWin, File Transfer and download the :diag:<filename>

To read it need the Tracex Tool powered by Mike BJ or the MessageDoctor SW by GVS.

21

6.5. STMI - GW Traces: - Do it if ISDN message (e.g. Setup) is going towards STMI, but you don't see an Invite
on Wireshark going out .
XTracer SW Instructions:
x1. To get the XTRACER SW go on Unify Intranet:
http://prodsu.mch4.global-intra.net/ => Tools/Links or
http://cur1303x.global-ad.net/foswiki/pub/HUSIM/XTracerDownload/setup.exe

x2.Access Web Based Management and connect to the Gateway.

x3. Connect to the STMI/HG35xx Card, then on
Maintenance -> Traces -> --> Trace Profiles => right mouse click on 1.1.2 SIP trk. General probl. and Activate Profile

x4. --> Scroll all the way to the top and right click on Trace Output Interfaces and click on Edit Trace Output Interfaces

--> Uncheck everything and check Switch Trace via LAN On, click on Apply button
--> Verify on Trace Format Configuration if all Header Output choices are set to Yes,
and the Trace Data is Full formatting with Parameter Expansion.
==> Click on the diskette icon to Save.
- If you're not able to get XTracer (Dev.request), choose Switch File Trace On and collect together on item x8.
x5 .Launch XTracer -> click on the lightning bolt,
On the Start Tab select Trace Type of HiPath2000 LDH (FP inside) and add you IP address in the IP address field.
Further windows asking Decoders, select NONE.
At the bottom, add where you want your file to be saved.
Click Start and do the test or wait until fail occurs....
x6.Can be saved in multiple files click on the Ring Buffer Tab (on Start Trace Tabs)
Next File Every (size) ******
The maximum file size of one trace is 1.99Gb.
Can also start another trace/card in parallel (change the Tracing File destination name)
x7. When finished stop the trace as this overload the STMI processor.
Maintenance->Traces->Trace Components => right mouse click -> Stop All Trace Components
and click on the diskette icon to Save. Uncheck Switch Trace via LAN on Trace Output Interfaces.
x8. Collect all STMI card logs with:
Maintenance->Actions->Manual Actions->All logs=> right click -> Load via HTP -> Load
Save on your PC.

22

6.6. STMI - Loadware ( LW ).

- LW is the Operational System SW ( including the SIP stack ) that runs inside the card on STMI/NCUI Flash Memory (FM).
- STMI LW is stored on the rmx HD area :PDS:APSP/LTG/LG98/PZKSTI40
- New LW can be consulted on SWS ( Unify - SoftWare Supply Server ), LW Hot Fix.
- How to replace the LW; see the doc. SWS and Hotfix Guide, file HP4k_SWS_HF_Guide.pdf
- To load a new STMI LW, takes about 13 minutes and card will be READY.
- When STMI/NCUI card resets/reboot/power off-on/pull-push, there is a card's flash memory (FM) check against to the lw stored on HD area :PDS:....,
if the lw is the same (FM = HD), card boots in about 90 seconds... If not STMI takes 13 minutes to load new LW from HD .

Condition for that check:

----------------------------------------------------------------------------------------------------------------Card Loadware load behaviour on V6R1 down versions:
<CHA-FUNSU: FLASH,
PARTNO =
FCTID =
ACTION = ?
ACTION
: ACTION SET OR RESET LOADWARE ON BOARD
POSS. VALUES : LOAD = FORCED LOAD FOR THE BOARD from the HD (always 13 min. to STMI=ready; no FM=HD check).
RESET = RESET OF THE FORCED LOAD
ACTION = RESET;
CHA-FUNSU:FLASH,,,RESET; ==> /* return the funsu function to standard value; NO forced lw load always....
------------------------------------------------------------------------------------------------------------------------------------------------Card Loadware load behaviour on V6R2 up:
<DIS-ZANDE:LOADBHV,;
HRBHV:
==========================
LOAD = NOLOAD => /* on Hard Restart, no forced lw load from hd.
LWSRC: => /* LW source for Card Flash Memory (FM) load after card reset
==========================
PARTNO FCTID LOADDEV
------ ----- ----Q2324-X500 1 HD => /* Force load lw from HD to the card (always 13 min.to STMI=ready; no FM=HD check).
Q2324-X510 1 FLASH => /* check first if flash memory lw = HD lw; if not load from HD.
AFTER HARDRESTART / RELOAD, VALUES FOR HRBHV & LWSRC WILL BE SET BACK TO DEFAULT NOLOAD / FLASH
This amo zande, lw behaviour does NOT apply for NCUI or SoftGate...
----------------------------------------------------------------------------------------------------------------------------------------------------------!! V7 Exception on the condition above; no LW FM=HD check at all with ZANDE: NOIPBLWL= YES. Quick, fast IN Service (READY) !!
New on V7 AMO- ZANDE: ALLDATA2, NOIPBLWL = yes; /* If yes means NO IP boards lw load from hd. You get quicker reload as stmi/ncui loads from flash
(STMI=90 sec. no hd check); but be aware that you should later change noipblwl=NO and reboot the stmi/ncui cards manually to get newest lw from the new
replaced/upgraded HD...
Summary: NOIPBLWL = yes; => STMI/NCUI will NEVER load LW from HD. STMI ready in 90 sec. with old/exist LW from card Flash Memory .
NOIPBLWL = no; => behaviour is equal as on V6, V5. described as above on Card LW load topic..
----------------------------------------------------------------------------------------------------------------------------------------------- --------------------------------

6.6.1. Ways to check running LW:

- See on WBM, at the botton of figure from the item 5.1

or more info is on same WBM-. Explorers -> Basic Set. -> SW Build

or also go to Assistant -> Expert Mode -> Gateway Manager ... => "Update Board List"
- ComWin rmx-amo
<sta-list::pds:apsp/ltg/lg98/pzksti40,,200,t;
FILE NAME: :PDS:APSP/LTG/LG98/PZKSTI40
TYPE
: RMX
0000 :....04/09/1414:19:21.MSR>I386pzksti40.A2.001-005.00pzksti40..
0040 :............h.......X}[email protected]..........

=> /* compiled on April/09/2014 @ 14:19:21

/* lw version PZKSTI40.A2.001-005

<STA-LIST::PAS:HIM/PB,,,M,N; /* Hipath Inventory Management/Printed Board circuit /*

FILE NAME: :PAS:HIM/PB
01|001|1|:PDS:APSP/LTG/LG80/PZESLA40
|--|01/07/13 15:31:39|
=> /* card SLMAE current running lw pzesla40
01|002|1|:PDS:APSP/LTG/LG83/PZDSMO10
|--|12/19/12 17:10:47| => /* SLMO24 on pen 1-2-1 pzdsmo10 lw, Dec.19, 2012
01|011|1|:PDS:APSP/LTG/LG98/PZKSTI40
|00|04/09/14 14:19:21|
=> /* ltu=1 slot=11 STMI lw from April/09/2014

23

6.7. STMI - CLI = Command Line Interface.

6.7.1. OS4k - Assistant -> Expert Mode -> Gateway Dashboard => SSH = CLI

6.7.2. Can get CLI also from your PC with serial null cable DB9 to the STMI - Service Port: 38400 N-8-1
On this serial connection, you can follow the booting messages when card is loading....
6.7.3. Login with username: TRM password: HICOM
If this not work do < CHANGE-CGWB:MTYPE=CGW,LTU=1,SLOT=11,TYPE=SERVIF,LOGINTRM="TRM",PASSW=HICOM;
6.7.4. Some intersting commands..
Welcome to the HG 3500 V7 pzksti40.A2.001-005 Command Line Interpreter.
vxTarget> help

=> shows all possible commands

get write access

get id eth_link_mode => should be 100M Full Duplex
ping <ip address>
reset
reset factory
save configuration
switch console trace on
show active traces
switch console trace off
reset active traces
show
show
show
show
show
show
show
show
show
show
show
show
show
show
show

=> shows the trace in real time; only on serial cable DB9 connection

arp cache
boot
default gateway
flash => directories/files
if counters => dropped frames
if states => if = interfaces
ip address
memory
mscindexes => number of call connections
routes
time
uptime
versions => running lw version
cpu usage
file_ascii <path and file name>

Ctrl W
logout

=> goes to debug/development mode

24

7. Default SIP -to- SS7 ISUP ( ISDN ) Cause Codes:

ISUP (TDCSU) Cause Value - SIP (STMI GW) Response (400 ~ 699 )
1 unallocated number - 404 Not Found
2 no route to network - 404 Not Found
3 no route to destination - 404 Not Found
16 normal call clearing - --- (*)
17 user busy - 486 Busy here
18 no user responding - 408 Request Timeout
19 no answer from the user - 480 Temporarily unavailable
20 subscriber absent - 480 Temporarily unavailable
21 call rejected - 403 Forbidden (+)
22 number changed (s/ o diagnostic) - 410 Gone
22 number changed ( w/ diagnostic) - 301 Moved permanently
23 redirection to new destination - 410 Gone
26 non-selected user clearing - 404 Not Found (=)
27 destination out of order - 502 Bad Gateway
28 address incomplete - 484 Address incomplete
29 facility rejected - 510 Not implemented
31 normal unspecified - 480 Temporarily unavailable Resource unavailable
34 no circuit available - 503 Service unavailable
38 network out of order - 503 Service unavailable
41 temporary failure - 503 Service unavailable
42 switching equipment congestion - 503 Service unavailable
47 resource unavailable - 503 Service unavailable Service or option not available
55 incoming calls barred within CUG - 403 Forbidden
57 bearer capability not authorized - 403 Forbidden
58 bearer capability not presently available - 503 Service unavailable
65 bearer capability not implemented - 488 Not Acceptable here
70 Only restricted digital information bearer capability is available (National use) - 488 Not Acceptable here
79 service or option not implemented - 501 Not implemented
87 user not member of CUG - 403 Forbidden
88 incompatible destination - 503 Service unavailable
95 - Invalid message - 400 Bad request
102 Call Setup Time-out Failure - 504 Gateway timeout
111 Protocol Error Unspecified - 500 Server internal error Interworking
127 Internal Error - interworking unspecified - 500 Server internal error
- - - 500 Server internal error (default)

SIP Status Code to ISDN Cause Code Mapping

400 Bad Request 41 Temporary failure
401 Unauthorized 21 Call rejected (*)
402 Payment required 21 Call rejected
403 Forbidden 21 Call rejected
404 Not Found 1 Unallocated number
405 Method not allowed 63 Service or option unavailable
406 Not acceptable 79 Service/option not implemented (+)
407 Proxy authentication required 21 Call rejected (*)
408 Request timeout 102 Recovery on timer expiry
409 - Conflict 41 - Temporary failure
410 Gone 22 Number changed (w/o diagnostic)
411 - Length required 127 - Interworking, unspecified

25

413 Request Entity too long 127 Interworking (+)

414 Request URI too long 127 Interworking (+)
415 Unsupported media type 79 Service/option not implemented (+)
416 Unsupported URI Scheme 127 Interworking (+)
402 Bad extension 127 Interworking (+)
420 - Bad extension 127 - Interworking, unspecified
421 Extension Required 127 Interworking (+)
423 Interval Too Brief 127 Interworking (+)
480 Temporarily unavailable 18 No user responding
481 Call/Transaction Does not Exist 41 Temporary Failure
482 Loop Detected 25 Exchange routing error
483 Too many hops 25 Exchange routing error
484 Address incomplete 28 Invalid Number Format (+)
485 Ambiguous 1 Unallocated number
486 Busy here 17 User Busy
487 Request Terminated --- (no mapping)
488 Not Acceptable here --- by warning header
500 Server internal error 41 Temporary Failure
501 Not implemented 79 Not implemented, unspecified
502 Bad gateway 38 Network out of order
503 Service unavailable 41 Temporary Failure
504 Service time-out 102 Recovery on timer expiry
505 Version Not supported 127 Interworking (+)
513 Message Too Large 127 Interworking (+)
580 - Precondition Failed 47 - Resource unavailable, unspecified
600 Busy everywhere 17 User busy
603 Decline 21 Call rejected
604 Does not exist anywhere 1 Unallocated number
606 Not acceptable --- by warning header
(*) ISDN Cause 16 will usually result in a BYE or CANCEL
(+) If the cause location is user than the 6xx code could be given rather than the 4xx code. the cause value
received in the H.225.0 message is unknown in ISUP, the unspecified cause value of the class is sent.
(=) ANSI procedure

The information provided in this document contains descriptions or characteristics of performance which in case of actual use do not always
apply as described or which may change as a result of further development of the products.
Availability and technical specifications are subject to change without notice.
An obligation to provide the respective characteristics or support and warranty shall only exist if expressly agreed in the terms of contract.
Neither the author nor Unify shall be liable for errors, omissions or damages resulting from the use of the informations contained herein..
The comments expressed belong to the author and are not necessarily those of Unify Inc.
OpenScape, OpenStage and HiPath are registered trademarks of Unify.
All other company, brand, product and service names are trademarks or registered trademarks of their respective holders.

26