Ata 28

28-10-00
DETAILED VISUAL
INSPECTION OF FUEL AREA
BY VIDEO CAMERA
DVI 10005-002
1
MAR15
ZONING DATA
___________
ZONE
ACCESS
: 293
294
522
622
: 293BL 294BR
522KT
622KT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
GSE
: 01
01
01
01
___
MEN
ACCESS PLATFORM
ENDO/VIDEO SYSTEM OLYMPUS
INTERFACE TOOLING
TELESCOPIC STICK SUPPORT
_________
MAN-HOURS
IPLEX SA II R
98S57205043
98S57005003
PUBLICATION
___________
JIC
JIC
JIC
JIC
JIC
JIC
: DEFUELING
: INERTING
: DC AND AC EXTERNAL POWER
SUPPLY
: REMOVAL AND INSTALLATION
OF WING-TO-FUSELAGE
FAIRINGS
: DETAILLED VISUAL
INSPECTION OF FUEL
PUMP HARNESS
: DETAILLED VISUAL
INSPECTION OF HIGH
LEVEL SENSOR
AH
12-11-00-DFG-10000
28-12-00-DAR-10000
24-40-00-EAD-10000
53-93-00-RAI-10000
28-21-71-DVI-10000
28-25-73-DVI-10000
28-10-00
DVI 10005-002
2-400 PAGE
1
MAR 01/15
DETAILED VISUAL
BY VIDEO CAMERA
28-10-00
DVI 10005-002
2
MAR15
PUBLICATION
___________
JIC
JIC
: DETAILLED VISUAL
INSPECTION OF FUEL
QUANTITY PROBES
: OPENING AND CLOSING OF
WING BOX ACCES DOORS
OPENING AND CLOSING OF
WING BOX ACCESS DOORS
AH
28-42-72-DVI-10000
57-00-00-OAC-10000
28-10-00
DVI 10005-002
2-400 PAGE
2
MAR 01/15
28-10-00
DETAILED VISUAL
BY VIDEO CAMERA
001
DVI 10005-002
3
MAR15
_______________________________
FUEL
SYSTEM SAFETY REQUIREMENTS
1. PRESENCE OF SAFETY PERSONNEL.
2. INSTALL EXPLOSIMETER IN FIRE RISK AREA (IN
CASE OF PARTIAL OR COMPLETE REFUELING), IN
ACCORDANCE WITH OPERATOR}S NATIONAL
REQUIREMENTS.
3. INSTALL SMOKING PROHIBITED WARNING NOTICES
AROUND FIRE RISK AREA (IN CASE OF PARTIAL OR
COMPLETE REFUELING), IN ACCORDANCE WITH
OPERATOR}S NATIONAL REQUIREMENTS.
4. PERFORM EQUIPOTENTIAL CONNECTION BETWEEN THE
TANKER AND THE AIRCRAFT (IN CASE OF FUEL
TRANSFER ONLY).
5. USE ONLY EXPLOSION PROOF INSPECTION LIGHTS
WHEN PERFORMING WORK.
6. COMPLY WITH SAFETY INSTRUCTIONS OF
ELECTRICAL POWER SUPPLY CHAPTER.
7. ANY SPILLED FUEL MUST BE ABSORBED AND DRIED.
002
_________
DEFUELING
SEE JOB INSTRUCTION CARD
121100-DFG-10000
003
________
INERTING
281200-DAR-10000
004
______________________________________________
DE-ENERGIZATION
OF AIRCRAFT AC AND DC NETWORKS
244000-EAD-10000
*** CONTINUED ***
AH
28-10-00
DVI 10005-002
2-400 PAGE
3
MAR 01/15
28-10-00
DETAILED VISUAL
BY VIDEO CAMERA
005
DVI 10005-002
4
MAR15
____________________________________
REMOVAL
OF WING-TO-FUSELAGE FAIRINGS
539300-RAI-10000
NOTE : REMOVE WING TO FUSELAGE FAIRINGS INDICATED IN THE ACCESS SECTION ON PAGE 1
OF THIS JOB INSTRUCTION CARD.
006
DETAILED VISUAL INSPECTION OF FUEL PUMP

_______________________________________
HARNESS
_______
282171-DVI-10000
007
DETAILED VISUAL INSPECTION OF HIGH LEVEL

________________________________________
SENSOR
______
282573-DVI-10000
008
DETAILED VISUAL INSPECTION OF FUEL QUANTITY

___________________________________________
PROBES
______
284272-DVI-10000
009
_______________________________
OPENING
OF WING BOX ACCES DOORS
570000-OAC-10000
OPEN WING BOX ACCESS DOOR AS NECESARY.
010
DETAILED VISUAL INSPECTION OF

_____________________________
FUEL TANKS
__________
REF.FIG.:
REF.FIG.:
REF.FIG.:
REF.FIG.:
281000-DVI-00100
281000-DVI-00105
281000-DVI-00110
281000-DVI-00115
*** CONTINUED ***
AH
28-10-00
DVI 10005-002
2-400 PAGE
4
MAR 01/15
28-10-00
DETAILED VISUAL
BY VIDEO CAMERA
DVI 10005-002
5
MAR15
REF.:NDTM CHAP.57-11-00 PART 1/9

57-21-00 PART 1/9
WITH VIDEO CAMERA, INSPECT THE FOLLOWING
ITEMS :
1. FUEL QUANTITY PROBE, LOW LEVEL DETECTOR
AND TERMISTANCE SENSOR HARNESSES.
CHECK THAT :
- HARNESS ATTACHMENT IS CORRECT.
- HARNESSES ARE NOT FRAYED.
- HARNESSES ARE NOT LOOSENED.
- CLAMPS ARE CORRECTLY INSTALLED
2. FUEL TEMPERATURE SENSOR
CHECK THAT THE SENSOR HAS NO VISUAL DAMAGES
3. FUEL PUMP
CHECK THAT:
- ALL PUMP PARTS ARE CORRECTLY INSTALLED.
- PRESS SWITCH HARNESS IS IN GOOD CONDITION
AND CORRECTLY CLAMPED.
4. BRAIDS
CHECK THAT:
- BRAIDS ARE
- BRAIDS ARE
- BRAIDS ARE
SYSTEMS OR
- BRAIDS ARE
CORRECTLY INSTALLED.
NOT BROKEN,FRAYED OR CORRODED.
NOT IN CONTACT WITH SURROUDING
STRUCTURE.
NOT LOOSEN.
5. CLAMP CONDITION ON FUEL LINE

(ITEM 2 OF FIG.281000 DVI 00105)
INSPECT CLAMPS ON FUEL RETURN LINE FROM
MOTIVE FLOW VALVE TO ENGINE JET PUMP.
CHECK THAT CLAMPS ARE CORRECTLY INSTALLED.
CHECK CONDITION OF THE ELASTOMER SHEATH ON
CLAMPS.
*** CONTINUED ***
AH
28-10-00
DVI 10005-002
2-400 PAGE
5
MAR 01/15
28-10-00
DETAILED VISUAL
BY VIDEO CAMERA
DVI 10005-002
6
MAR15
-DAMAGE OF ELASTOMER SHEATH ON CLAMP (BROKEN

TORN OR MISSING) IS ACCEPTABLE FOR CONTINUE
SERVICE PROVIDED RE-ASSESSMENT OF THE CLAMP
CONDITION IS PERFORMED ON A CCHECK BASIS.
-DAMAGE OF FUEL LINE UNDERNEATH CLAMP IS NOT
ALLOWED FOR CONTINUE SERVICE WITHOUT PRIOR
ENGINEERING EVALUATION FROM ATR.
011
________________________________
CLOSING
OF WING BOX ACCESS DOORS
570000-OAC-10000
CLOSE THE ACCESS DOORS PREVIOUSLY OPENED.
012
_________________________________________
INSTALLATION
539300-RAI-10000
NOTE : INSTALL WING TO FUSELAGE FAIRINGS
PREVIOUSLY REMOVED.
R
013
________
CLOSE-UP
1. DISCONNECT AIRCRAFT FROM TANKER.
(IF IT HAS BEEN INSTALLED).
2. REMOVE SMOKING PROHIBITED WARNING NOTICES.
3. REMOVE EXPLOSIMETER.
4. REMOVE WARNING NOTICE PROHIBITING ENERGIZATION OF FUEL SYSTEM FROM FLIGHT COMPARTMENT.
5. CHECK THAT WORKING AREA IS CLEAN AND CLEAR
OF TOOLS AND MISCELLANEOUS ITEMS OF EQUIPMENT.
6. REMOVE PLATFORM.
*****
AH
E N D
O F
T E X T
*****
28-10-00
DVI 10005-002
2-400 PAGE
6
MAR 01/15
28-10-00
7
AH
ACCESS PANELS
DVI 10005-002
MAR15
28-10-00
DVI 10005-002
2-400
PAGE
7
MAR 01/15
28-10-00
8
AH
FUEL LINES INSTALLATION
DVI 10005-002
MAR15
28-10-00
DVI 10005-002
2-400
PAGE
8
MAR 01/15
28-10-00
9
AH
VENT LINES INSTALLATION
DVI 10005-002
MAR15
28-10-00
DVI 10005-002
2-400
PAGE
9
MAR 01/15
28-10-00
10
AH
TYPICAL BRAID
INSTALLATION
DVI 10005-002
MAR15
28-10-00
DVI 10005-002
2-400
PAGE
10
MAR 01/15
28-10-00
DETAILED VISUAL
BY WING PANEL REMOVAL
DVI 10010-003
1
MAR15
ZONING DATA
___________
ZONE
ACCESS
: 293
522
622
: 293BL
521AT
621CT
294
294BR
521CT 523BT
623BT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
: 01 ACCES PLATFORM
_________
MAN-HOURS
PUBLICATION
___________
JIC
JIC
JIC
JIC
JIC
JIC
JIC
: DEFUELING
: INERTING
: OUTBOARD WING LOAD
RELIEF (ENGINES/
PROPELLERS INSTALLED)
RELIEF (PROPELLERS
REMOVED)
RELIEF (ENGINES REMOVED)
OF WING-TO-FUSELAGE
FAIRINGS
: DETAILLED VISUAL
INSPECTION OF FUEL
PUMP HARNESS
AH
12-11-00-DFG-10000
28-12-00-DAR-10000
07-20-00-SOG-10010
07-20-00-SOG-10012
07-20-00-SOG-10014
53-93-00-RAI-10000
28-21-71-DVI-10000
28-10-00
DVI 10010-003
2-400 PAGE
1
MAR 01/15
DETAILED VISUAL
28-10-00
DVI 10010-003
2
MAR15
PUBLICATION
___________
JIC
JIC
JIC
JIC
JIC
: DETAILLED VISUAL
INSPECTION OF HIGH
LEVEL SENSOR
: DETAILLED VISUAL
INSPECTION OF FUEL
QUANTITY PROBES
OF CENTER WING
REMOVABLE PANELS
OF OUTER WINGS REMOVABLE
PANELS
: JACKING FOR A/C
MAINTENANCE OPERATIONS
AH
28-25-73-DVI-10000
28-42-72-DVI-10000
57-14-12-RAI-10000
57-24-12-RAI-10010
07-11-00-JUP-10000
28-10-00
DVI 10010-003
2-400 PAGE
2
MAR 01/15
28-10-00
DETAILED VISUAL
001
DVI 10010-003
3
MAR15
_______
WARNING
WARNING C.D.C.C.L.
CRITICAL DESIGN CONFIGURATION
CONTROL LIMITATION
THE FOLLOWING PROCEDURE IS APPLIED TO
A FUEL SYSTEM ITEM THAT IS IN THE CATEGORY
KNOWN AS A CRITICAL DESIGN CONFIGURATION
CONTROL LIMITATION.
CDCCL IDENTIFIES AN ITEM THAT CAN BE SOURCE OF
A POSSIBLE FUEL TANK IGNITION.
YOU MUST KEEP ALL CDCCL ITEMS IN THE APPROVED
CONFIGURATION.
DAMAGE,WEAR OR CHANGES TO A CDCCL ITEM CAN
CAUSE A POSSIBLE FUEL TANK EXPLOSION.
002
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
*** CONTINUED ***
AH
28-10-00
DVI 10010-003
2-400 PAGE
3
MAR 01/15
28-10-00
DETAILED VISUAL
DVI 10010-003
4
MAR15

003
_________
DEFUELING
121100-DFG-10000
004
________
INERTING
281200-DAR-10000
005
LOAD RELIEVING OF OUTER WING

____________________________
(ENGINES/PROPELLERS INSTALLED)
______________________________
072000-SOG-10010
NOTE : CHOOSE THE CORRECT DOCUMENTATION AMONG
THE THREE JIC AVAILABLE.
CHECK THE A/C CONFIGURATION
006

____________________________
(PROPELLERS REMOVED)
____________________
072000-SOG-10012
NOTE : MUST BE USE IN ACCORDANCE WITH THE
AIRCRAFT CONFIGURATION.
007

____________________________
(ENGINES REMOVED)
_________________
072000-SOG-10014
NOTE : MUST BE USE IN ACCORDANCE WITH THE
AIRCRAFT CONFIGURATION.
*** CONTINUED ***

AH
28-10-00
DVI 10010-003
2-400 PAGE
4
MAR 01/15
28-10-00
DETAILED VISUAL
008
DVI 10010-003
5
MAR15
____________________________________
REMOVAL
539300-RAI-10000
009
DETAILED VISUAL INSPECTION OF FUEL PUMP

_______________________________________
HARNESS
_______
282171-DVI-10000
010
DETAILED VISUAL INSPECTION OF HIGH LEVEL

________________________________________
SENSOR
______
282573-DVI-10000
011

___________________________________________
PROBES
______
284272-DVI-10000
012
REMOVAL OF WING REMOVABLE PANELS __________________________________

RIB 0 TO 13
___________
571412-RAI-10000
013
____________________________________
REMOVAL
OF OUTER BOX REMOVABLE PANEL
572412-RAI-10010
*** CONTINUED ***

AH
28-10-00
DVI 10010-003
2-400 PAGE
5
MAR 01/15
28-10-00
DETAILED VISUAL
014
DVI 10010-003
6
MAR15

_____________________________
FUEL TANKS
__________
REF.FIG.:
REF.FIG.:
REF.FIG.:
REF.FIG.:
281000-DVI-00100
281000-DVI-00105
281000-DVI-00110
281000-DVI-00115
INSPECT THE FOLLOWING ITEMS:

1. FUEL QUANTITY PROBE HARNESS.
CHECK THAT :
-HARNESSES ATTACHEMENT IS CORRECT.
-HARNESSES ARE NOT FRAYED.
-HARNESSES ARE NOT LOOSEN
-CLAMPS ARE CORRECTLY INSTALLED.
2. FUEL SENSOR TEMPERATURE.
CHECK THAT THE SENSOR HAS NO VISUAL DEFECT.
3. FUEL PUMP
CHECK THAT:
- ALL PUMP PARTS ARE CORRECTLY INSTALLED.
- PRESS SWITCH HARNESS IS IN GOOD CONDITION
AND CORRECTLY CLAMPED.
4. BRAIDS
CHECK THAT:
- BRAIDS ARE CORRECTLY INSTALLED
- BRAIDS ARE NOT BROKEN,FRAYED OR CORRODED
- BRAIDS ARE NOT IN CONTACT WITH THE
SUROUDING SYSTEM OR STRUCTURE.
- BRAIDS ARE NOT LOOSEN.
5. CLAMP CONDITION ON FUEL LINE
(ITEM 2 OF FIG.281000 DVI 00105)
INSPECT CLAMPS ON FUEL RETURN LINE FROM
MOTIVE FLOW VALVE TO ENGINE JET PUMP.
CHECK THAT CLAMPS ARE CORRECTLY INSTALLED.
CHECK CONDITION OF ELASTOMER SHEATH ON CLAMP
*** CONTINUED ***
AH
28-10-00
DVI 10010-003
2-400 PAGE
6
MAR 01/15
28-10-00
DETAILED VISUAL
DVI 10010-003
7
MAR15
-DAMAGE OF ELASTOMER SHEATH ON CLAMP (BROKEN

TORN OR MISSING) IS ACCEPTABLE FOR CONTINUE
SERVICE PROVIDED RE-ASSESSMENT OF THE CLAMP
CONDITION IS PERFORMED ON A CCHECK BASIS.
-DAMAGE OF FUEL LINE UNDERNEATH CLAMP IS NOT
ALLOWED FOR CONTINUE SERVICE WITHOUT PRIOR
ENGINEERING EVALUATION FROM ATR.
015
INSTALLATION OF WING REMOVABLE PANELS _______________________________________

RIB 0 TO 13
___________
571412-RAI-10000
016
__________________________________________
INSTALLATION
OF OUTER BOX REMOVABLE PANELS
572412-RAI-10010
017
_________________________________________
INSTALLATION
539300-RAI-10000
PREVIOUSLY REMOVED.
R
018
________
CLOSE-UP
OF TOOLS AND MISCELLANEOUS ITEMS OF EQUIP*** CONTINUED ***
AH
28-10-00
DVI 10010-003
2-400 PAGE
7
MAR 01/15
28-10-00
DETAILED VISUAL
DVI 10010-003
8
MAR15
MENT.
6. REMOVE PLATFORM.
019
____________________________________
LOWERING
OF AIRCRAFT ONTO ITS WHEELS
071100-JUP-10000
*****
AH
E N D
O F
T E X T
*****
28-10-00
DVI 10010-003
2-400 PAGE
8
MAR 01/15
28-10-00
9
AH
ACCESS PANELS
DVI 10010-003
MAR15
28-10-00
DVI 10010-003
2-400
PAGE
9
MAR 01/15
28-10-00
10
AH
FUEL LINES INSTALLATION
DVI 10010-003
MAR15
28-10-00
DVI 10010-003
2-400
PAGE
10
MAR 01/15
28-10-00
11
AH
VENT LINES INSTALLATION
DVI 10010-003
MAR15
28-10-00
DVI 10010-003
2-400
PAGE
11
MAR 01/15
28-10-00
12
AH
TYPICAL BRAID
INSTALLATION
DVI 10010-003
MAR15
28-10-00
DVI 10010-003
2-400
PAGE
12
MAR 01/15
28-11-00
CLEANING FOR REMOVAL OF

MICROBIOLOGIC DEBRIS
DEPOSIT IN FUEL TANK
CLN 10000-001
1
APR05
ZONING DATA
___________
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
___
MEN
BULK MATERIAL : METHYL ALCOHOL

DETERGENT
INSULATING ADHESIVE TAPE
_________
MAN-HOURS
11-006
11-009
08-032
PUBLICATION
___________
JIC
JIC
JIC
JIC
JIC
: DRAINING OF WATER FROM

FUEL TANK
OF CENTER WING
REMOVABLE PANELS
OF OUTER WINGS REMOVABLE
PANELS
OF FUEL ELECTRIC PUMP
: REFUELING
AH
12-24-28-DRN-10000
57-14-12-RAI-10000
57-24-12-RAI-10010
28-21-71-RAI-10000
12-11-00-FLG-10020
28-11-00
CLN 10000-001
2-400 PAGE
1
APR 01/05
28-11-00

001
CLN 10000-001
2
APR05
___________
PREPARATION
1. DEFUELING AND DRAINING OF TANK TO CLEAN.
A. CHECK OF THE CLOSING CROSS FEED VALVE.
- ON PANEL 25VU, MAKE CERTAIN THAT
FUEL/X FEED PUSHBUTTON SWITCH IS
RELEASED.
. FLOWBAR IS CROSSLINE.
- ON PANEL 121VU, OPEN SAFETY AND TAG THE
FOLLOWING CIRCUIT BREAKER :
2QE
FUEL/FUEL FEED/X FEED
B. DEFUEL THE TANK AND PERFORM A COMPLETE

DRAINING AS DESCRIBED INTO THE JOB INSTRUCTION CARD LISTED BELOW:
2. REMOVAL OF THE WING PANEL:
DEPENDING ON THE TANK TO BE CLEANED, REMOVE:
- EITHER THE CENTER WING REMOVAL PANEL
- OR THE OUTER WING REMOVAL PANEL
IN RESPECTING SCRUPULOUSLY THE PROCEDURE
DESCRIBED INTO THE JOB INSTRUCTION CARD
LISTED BELOW:
3. REMOVAL OF THE FUEL ELECTRIC PUMP:
IF IT}S NECESSARY FOR CLEANING THE CENTRAL
TANK, REMOVE THE FUEL ELECTRIC PUMP IN RESPECTING THE PROCEDURE DESCRIBED INTO THE JOB
INSTRUCTION CARD LISTED BELOW:
002
DRAINING OF WATER FROM

______________________
FUEL TANK
_________
122428-DRN-10000
*** CONTINUED ***
AH
28-11-00
CLN 10000-001
2-400 PAGE
2
APR 01/05
28-11-00

003
CLN 10000-001
3
APR05
REMOVAL OF WING REMOVABLE PANELS __________________________________

RIB 0 TO 13
___________
571412-RAI-10000
004
____________________________________
REMOVAL
OF OUTER BOX REMOVABLE PANEL
572412-RAI-10010
005
_____________________________
REMOVAL
282171-RAI-10000
006
CLEANING FOR REMOVAL OF MICROBIOLOGIC DEBRIS

____________________________________________
DEPOSIT IN FUEL TANKS
_____________________
1. PREPARATION OF DETERGENT MIXTURE :
MIXTE ONE (1) PART OF PRODUCT 11-009 TO
SIXTEEN (16) PART OF WATER.
2. USING A BRUSH, CLEAN CONTAMINED AREAS WITH
THE MIXTURE.
FOR THE CENTRAL TANK:
- CLOSE THE FEEDER TANK JET PUMP BY MEANS
ADHESIVE TAPE.
PAYING PARTICULAR ATTENTION :
- TO FUEL PUMP CANNISTER INLET SCREEN,
- TO FUEL GAGE,
- TO JET PUMP OF FEEDER TANK AND ENGINE
FEED,
- TO WATER DRAIN,
- TO VAPOR RELIEF VALVE AND THERMAL RELIEF
VALVE,
- TO PRESSURE SWITCH,
- TO TEMPERATURE PROBE.
*** CONTINUED ***
AH
28-11-00
CLN 10000-001
2-400 PAGE
3
APR 01/05
28-11-00

CLN 10000-001
4
APR05
3. RINSE WITH CLEAN WATER TO REMOVE DETERGENT

AND DEBRIS.
DRAIN AND MOP UP THE EXCESS WATER.
4. PREPARATION OF CLEANING MIXTURE :
CAUTION : METHYL ALCOHOL IS POISONOUS.
- WEAR PROTECTIVE CLOTHING,
- WEAR GOGGLES AND APPROPRIATED MASK,
- WEAR GLOVES.
NOTE:IF THIS PRODUCT COMES INTO CONTACT WITH
SKIN, WASH IMMEDIATELY WITH CLEAN WATER
MIXE ONE (1) PART OF PRODUCT 11-006 WITH ONE
(1) PART OF WATER.
IMPORTANT:THE CLEANING AGENT MUST NOT EXCEED
50% OF THE SOLUTION.
5. APPLY MIXTURE TO CONTAMINATED AREAS AND
SET WORKING THE PRODUCT BETWEEN 15 MINUTES
AND 2 HOURS.
6. RINCE TO CLEAN WATER TO REMOVE THE MIXTURE.
A. DRAIN OFF THE WATER AND MOP UP ALL TRACES
OF WATER.
B. BY MEANS HOT AIR BLOWER, DRY TANK INNER
SIDE, LINES AND EQUIPMENTS.
7. INSPECT THE TANK, VACUUM CLEAN ALL WATER
AND DEBRIS.
8. REMOVE ADHESIVE TAPE OF FEEDER TANK JET PUMP
CLEAN CARREFULY.
9. IF IT IS REMOVED, INSTALL THE FUEL ELECTRIC
PUMP BY USING THE PROCEDURE DESCRIBED INTO
THE JOB INSTRUCTION CARD LISTED BELOW:
10.INSTALL THE PANEL (CENTRAL OR OUTER) BY
*** CONTINUED ***
AH
28-11-00
CLN 10000-001
2-400 PAGE
4
APR 01/05
28-11-00

CLN 10000-001
5
APR05
USING THE PROCEDURE DESCRIBED INTO THE JOB

INSTRUCTION CARD LISTED BELOW:
007
__________________________________
INSTALLATION
282171-RAI-10000
008
INSTALLATION OF WING REMOVABLE PANELS _______________________________________

RIB 0 TO 13
___________
571412-RAI-10000
009
__________________________________________
INSTALLATION
OF OUTER BOX REMOVABLE PANELS
572412-RAI-10010
010
________
CLOSE-UP
MAKE CERTAIN THAT ANY TOOLS, EQUIPMENTS OR
PRODUCT HAVE NOT FORGOTTEN.
CLEAN TRACES LEFT ON THE WING.
REMOVE ACCESS PLATFORMS.
ON PANEL 121VU :
REMOVE SAFETY CLIPS AND CLOSE CIRCUIT BREAKER :
2QE.
AFTER THE DELAY RECOMMANDED INTO PREVIOUS JOB
INSTRUCTION CARD, PERFORM REFUELING.
011
_________
REFUELING
121100-FLG-10020
*****
AH
E N D
O F
T E X T
*****
28-11-00
CLN 10000-001
2-400 PAGE
5
APR 01/05
28-11-00
DETAILLED VISUAL INSPECTION OF WING FUEL

BARRIER PLATE
DVI 10000-001
1
APR05
ZONING DATA
___________
ZONE
: 520
620
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
GSE
: 01 ACCESS PLATFORM
AH
___
MEN
_________
MAN-HOURS
28-11-00
DVI 10000-001
2-400 PAGE
1
APR 01/05
28-11-00
DETAILLED VISUAL INSPECTION OF WING FUEL

BARRIER PLATE
001
DVI 10000-001
2
APR05
DETALLED VISUAL INSPECTION OF FUEL BARRIER

__________________________________________
PLATE
_____
REF. FIG. 281100-DVI-00100
ON LOWER WING SURFACE, NEAR THE NACA INTAKE :
- ACCESS TO FUEL BARRIER PLATE
- CLEAN BARRIER PLATE
- PERFORM A DETAILLED VISUAL INSPECTION OF
THE PLATE.
- CHECK INTEGRITY OF THE PLATE AND FASTENER
CONDITION.
*****
AH
E N D
O F
T E X T
*****
28-11-00
DVI 10000-001
2-400 PAGE
2
APR 01/05
28-11-00
3
AH
OVERFLOW FUEL BARRIER

PLATE
DVI 10000-001
APR05
28-11-00
DVI 10000-001
2-400
PAGE
3
APR 01/05
28-11-00
GENERAL VISUAL INSPECTION OF WING LOWER

SURFACE FUEL LEAK
GVI 10000-001
1
MAR11
ZONING DATA
___________
ZONE
: 520
620
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
AH
___
MEN
_________
MAN-HOURS
28-11-00
GVI 10000-001
2-400 PAGE
1
MAR 01/11
28-11-00
GENERAL VISUAL INSPECTION OF WING LOWER

SURFACE FUEL LEAK
001
GVI 10000-001
2
MAR11
GENERAL VISUAL INSPECTION OF LOWER WING SURFACE

_______________________________________________
FOR FUEL LEAKS
______________
REF. FIG. 281100-GVI-00100
FROM GROUND, VISUALLY CHECK LOWER WINGS SURFACE
FROM RIB 4 TO RIB 22 FOR FUEL LEAK.
PARTICULAR ATTENTION NEED TO BE PAID AT THE
FOLLOWING AREAS :
- ELECTRICAL PUMP ACCESS
- JACKING PAD
- RIB 13
- RIB 22 TO RIB 23 (SURGE TANK AREA).
IF FUEL LEAK IS DETECTED, REFER TO SRM
(STRUCTURAL REPAIR MANUAL) CHAPTER 51-73-10.
*****
AH
E N D
O F
T E X T
*****
28-11-00
GVI 10000-001
2-400 PAGE
2
MAR 01/11
28-11-00
3
AH
FUEL LEAK AREA

INSPECTION
GVI 10000-001
MAR11
28-11-00
GVI 10000-001
2-400
PAGE
3
MAR 01/11
28-11-72
REMOVAL AND INSTALLATION

OF WINGS WATER DRAIN
RAI 10000-001
1
MAR12
ZONING DATA
___________
ZONE
ACCESS
: 522
622
: 522AZ 522CT
622AZ 622CT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
: 01 UNDERWING ACCESS PLATFORM

01 TOP SKIN ACCESS PLATFORM
01 WATER DRAIN PURGE TOOL
98S12003000000
SPARE
: 06 WATER DRAIN
02 WATER DRAIN
281170-01
281170-02
EXPENDABLE
: 08
06
04
03
281170-01
281170-01
281170-02
281170-02
O-RING
NUT
O-RING
NUT
BULK MATERIAL : BALTANE

MEK
PETROLATUM
SEALANT
SEALANT
SEALANT
_________
MAN-HOURS
11-004
11-003
04-012
09-019
09-001
09-002
PUBLICATION
___________
JIC

AH
57-00-00-OAC-10000
28-11-72
RAI 10000-001
2-400 PAGE
1
MAR 01/12

28-11-72
RAI 10000-001
2
MAR12
PUBLICATION
___________
JIC
JIC

OF NACA INTAKE
AH
28-12-71-RAI-10000
57-00-00-OAC-10000
28-11-72
RAI 10000-001
2-400 PAGE
2
MAR 01/12
28-11-72

001
RAI 10000-001
3
MAR12
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
1. CHECK FUEL LEVEL (PERFORM DEFUELING OPERATION IF REQUIRED).
2. INSTALL WARNING NOTICE IN FLIGHT COMPARTMENT
PROHIBITING ENERGIZATION OF FUEL SYSTEM.
3. INSTALL PLATFORM, TO GAIN ACCESS TO WING
LOWER SURFACE.
4. INSTALL PLATFORM, TO GAIN ACCESS TO WING
UPPER SURFACE.
5. FOR REMOVAL OF THE WATER DRAINS FOLLOWS:
*** CONTINUED ***
AH
28-11-72
RAI 10000-001
2-400 PAGE
3
MAR 01/12
28-11-72

RAI 10000-001
4
MAR12
RIB 4 AND 5
5007QL (5008QL)
RIB 5 AND 6
5005QL (5006QL)
RIB 12 AND 13 5003QL (5004QL)
REMOVE ACCESS DOORS 522CT (622CT),AND
522AZ (622AZ) AS DESCRIBED IN PARAGRAPH 3.
6. FOR REMOVAL OF THE WATER DRAINS FOLLOWS:
RIB 23 AND 24 5001QL (5002QL)
REMOVE NACA INTAKE AS DESCRIBED IN
PARAGRAPH 4.
003
_______________________________
OPENING
570000-OAC-10000
004
____________________________
REMOVAL
OF THE NACA INTAKE
281271-RAI-10000.
005
REMOVAL OF WATER DRAINS BETWEEN RIB 5 TO 6

__________________________________________
AND RIB 12 TO 13
________________
REF. FIG. 281172-RAI-00100
1. INTO TANK, REMOVE NUTS (1). DISCARD NUTS.
2. REMOVE SCREWS (2).
3. REMOVE WATER DRAIN (3).
4. REMOVE O-RINGS (4) AND (5). DISCARD O-RINGS.
5. CLEAN CARREFULLY SEALANT ON WATER DRAIN AND
ON WATER DRAIN HOUSING WITH MATERIAL 11-003
AND 11-004B.
6. BLANK ORIFICES OF REMOVED EQUIPMENT.
7. PROTECT REMOVED COMPONENT INSTALLATION AREA.
*** CONTINUED ***
AH
28-11-72
RAI 10000-001
2-400 PAGE
4
MAR 01/12
28-11-72

006
RAI 10000-001
5
MAR12
___________________________________________
REMOVAL
OF WATER DRAIN BETWEEN RIB 23 TO 24
REF. FIG. 281172-RAI-00110
1. INTO TANK:
A. REMOVE CAP OF SEALANT (1).
B. REMOVE NUTS (2). DISCARD NUTS.
C. REMOVE SEALANT AROUND THE WATER DRAIN
BASE.
3. REMOVE WATER DRAIN (4).
5. CLEAN CARREFULLY SEALANT ON WATER DRAIN AND
INTO TANK WITH MATERIAL 11-003 OR 11-004B.
007
INSTALLATION OF WATER DRAINS BETWEEN RIB 5 TO 6

_______________________________________________
AND RIB 12 TO 13
________________
REF. FIG. 281172-RAI-00100
1. PREPARATION OF REPLACEMENT COMPONENT (IF
REQUIRED).
2. INSTALL O-RINGS (4) AND (5).(O-RINGS MUST BE
PREVIOUSLY LUBRICATED WITH MATERIAL 04-012).
3. CLEAN BONDING PLATE AND APPLY A FILM OF
GREASE.
4. APPLY A LAYER OF MATERIAL 09-019 ON WATER
DRAIN HOUSING.
5. INSTALL WATER DRAIN (3).
*** CONTINUED ***
AH
28-11-72
RAI 10000-001
2-400 PAGE
5
MAR 01/12
28-11-72

RAI 10000-001
6
MAR12
6. INSTALL SCREWS (2).

7. INTO TANK, INSTALL NUTS (1).TIGHTEN.
008
INSTALLATION OF WATER DRAIN BETWEEN RIB 23 TO

_____________________________________________
24
__
REF. FIG. 281172-RAI-00110
REQUIRED).
2. INSTALL O-RINGS (5) AND (6).(O-RINGS MUST BE
PREVIOUSLY LUBRICATED WITH MATERIAL 04-012).
GREASE.
4. INSTALL WATER DRAIN (4).
6. INTO TANK:
A. INSTALL NUTS (2).TIGHTEN (TIGHTENING TORQUE 44.3 TO 53.1 LBF.IN/0.5 TO 0.6 M.DAN)
B. APPLY SEALANT CAP (1) ON NUTS.
C. APPLY A LAYER OF SEALANT 09-002 AROUND
WATER DRAIN.
D. APPLY A LAYER OF SEALANT 09-001 AROUND
ATTACHMENTS.
009
________
CLOSE-UP
1. INSTALL WATER DRAINS FOLLOWS:
RIB 23 AND 24 5001QL (5002QL) AND INSTALL
NACA INTAKE AS DESCRIBED IN PARAGRAPH 11.
2. INSTALL WATER DRAINS FOLLOWS:
RIB 4 AND 5
5007QL (5008QL)
RIB 5 AND 6
5005QL (5006QL)
*** CONTINUED ***
AH
28-11-72
RAI 10000-001
2-400 PAGE
6
MAR 01/12
28-11-72

RAI 10000-001
7
MAR12
RIB 12 AND 13 5003QL (5004QL) ET INSTALL

ACCESS DOORS 522AZ (622AZ), 522CT (622CT)
AS DESCRIBED IN PARAGRAPH 10.
3. MAKE CERTAIN THAT WORKING AREA IS CLEAN AND
CLEAR OF TOOLS AND MISCELLANEOUS ITEMS OF
EQUIPMENT.
4. RESTORE AIRCRAFT TO ITS NORMAL CONFIGURATION
010
________________________________
CLOSING
570000-OAC-10000
011
_________________________________
INSTALLATION
OF THE NACA INTAKE
281271-RAI-10000.
012
____________________
CHECK
OF WATER DRAIN
1. PERFORM COMPLETE REFUELLING OF AIRCRAFT.
2. CHECK THAT THERE ARE NO SIGNS OF FUEL
LEAKAGE OR SEEPAGE.
3. PLACE A CONTAINER UNDER THE DRAIN TO BE
CHECKED.
4. MANEUVER WATER DRAIN USING PURGE TOOL.
5. MAKE CERTAIN THAT FUEL FLOWS.
6. RELEASE PRESSURE ON PURGE TOOL.
7. CHECK THAT THERE ARE NO SIGNS OF FUEL
LEAKAGE OR SEEPAGE.
*** CONTINUED ***

AH
28-11-72
RAI 10000-001
2-400 PAGE
7
MAR 01/12
28-11-72

013
RAI 10000-001
8
MAR12
________
CLOSE-UP
6. REMOVE PLATFORM.
*****
AH
E N D
O F
T E X T
*****
28-11-72
RAI 10000-001
2-400 PAGE
8
MAR 01/12
28-11-72
9
AH
WATER DRAIN BETWEEN RIB

5 TO 6 AND 12 TO 13
RAI 10000-001
MAR12
28-11-72
RAI 10000-001
2-400
PAGE
9
MAR 01/12
28-11-72
10
AH
WATER DRAIN BETWEEN RIB

23 TO 24
RAI 10000-001
MAR12
28-11-72
RAI 10000-001
2-400
PAGE
10
MAR 01/12
28-12-00
INERTING
DAR 10000-001
1
APR05
ZONING DATA
___________
ZONE
: 522
622
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
MECHANIC
___
MEN
_________
MAN-HOURS
02
ELAPSED TIME
GSE
: 02 NITROGEN BOTTLE
01 LP REDUCING VALVE 3 BARS
01 FLEXIBLE HOSE
BULK MATERIAL : SYNTHETIC FOAM

ADHESIVE TAPE
PUBLICATION
___________
JIC
: DRAINING OF WATER FROM

FUEL TANK
AH
12-24-28-DRN-10000
28-12-00
DAR 10000-001
2-400 PAGE
1
APR 01/05
28-12-00
INERTING
DAR 10000-001
2
001
APR05
___________________________
PRECAUTIONS
BEFORE INERTING
NOTE : TANK INERTING MUST BE MANDATORILY PERFORMED BEFORE ANY OPERATION IN TANKS
(RISKS OF FIRE OR EXPLOSION).
1. TANK INERTING MUST BE CARRIED OUT IN THE
OPEN AIR OR IN A CORRECTLY VENTILATED HANGAR
ONLY.
- PARK THE AIRCRAFT NEAR THE HANGAR EXIT,
FACING OUTWARDS.
2. THE AIRCRAFT TANKS SHOULD BE COMPLETELY
DRAINED (UNTIL DRY) AS FOLLOWS :
NOTE : DO NOT REMOVE THE NO SMOKING
WARNING NOTICES INSTALLED DURING THE
DRAINING.
002
DRAINING OF WATER FROM

______________________
FUEL TANK
_________
122428-DRN-10000
003
__________________
INERTING
PROCEDURE
REF. FIG. 281200-DAR-00100
NOTE : (1) MAKE CERTAIN THAT CROSS-FEED VALVE
IS CLOSED.
(2) AS INERTING OF BOTH TANKS IS IDENTICAL, ONLY LEFT WING INERTING WILL BE
TREATED.
1. OPEN TANK OVERWING REFUELING CAP.
2. INSERT HOSE IN NACA INTAKE.
*** CONTINUED ***
AH
28-12-00
DAR 10000-001
2-400 PAGE
2
APR 01/05
28-12-00
INERTING
DAR 10000-001
3
APR05
3. MAINTAIN THE HOSE IN NACA INTAKE AND SEAL

USING SYNTHETIC FOAM AND ADHESIVE TAPE.
4. CONNECT HOSE TO PRESSURE REDUCING VALVE OF A
BOTTLE (ADJUST PRESSURE UNTIL READING ON
PRESSURE GAGE REACHES 2 BARS).
5. OPEN NITROGEN VALVE.
6. PERFORM SAME OPERATION WITH THE SECOND
BOTTLE WHEN THE FIRST IS EMPTY.
7. WHEN THE TWO BOTTLES ARE EMPTY :
- CLOSE OVERWING REFUELING CAP.
- REMOVE HOSE FROM NACA INTAKE AND SEAL WITH
PLASTIC FILM HELD WITH ADHESIVE TAPE.
NOTE : INERTING EFFECTS SHALL NOT EXCEED
48 HOURS.
004
________
CLOSE-UP
1. REMOVE ADHESIVE TAPE, PLASTIC FILM AND
SYNTHETIC FOAM INSTALLED DURING THIS
OPERATION.
2. CHECK FOR FOREIGN BODIES IN NACA INTAKE.
3. REMOVE PLATFORM.
4. REMOVE NO SMOKING WARNING NOTICES.
5. REMOVE NITROGEN BOTTLES.
EQUIPMENT.
*****
AH
E N D
O F
T E X T
*****
28-12-00
DAR 10000-001
2-400 PAGE
3
APR 01/05
28-12-00
4
AH
FUEL TANKS INERTING
DAR 10000-001
APR05
28-12-00
DAR 10000-001
2-400
PAGE
4
APR 01/05
28-12-71

OF NACA INTAKE
RAI 10000-001
1
MAR12
ZONING DATA
___________
ZONE
: 522
622
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
: 01 TOP SKIN ACCESS PLATFORM

01 DRAINING TOOL-GRAVITY
01 TORQUE WRENCH
97A28002117002
SPARE
: 01 NACA INTAKE
281270-08-310
EXPENDABLE
: 01 SEAL
281270-08-320
BULK MATERIAL : POLYSULFIDE SEALANT

GREASE
SEALANT
AH
_________
MAN-HOURS
09-002
04-001
09-016
28-12-71
RAI 10000-001
2-400 PAGE
1
MAR 01/12
28-12-71

OF NACA INTAKE
001
RAI 10000-001
2
MAR12
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
________________________
REMOVAL
OF NACA INTAKE
REF. FIG. 281271-RAI-00100
1. BY MEANS OF THE TOOL, ACTUATE THE WATER
DRAIN LOCATED AT EXTEMITY OF THE WING AND
CHECK THAT THERE IS NO FUEL IN VENT SURGE
TANK.
3. INSTALL PLATFORM TO GAIN ACCESS TO WING
LOWER SURFACE.
*** CONTINUED ***
AH
28-12-71
RAI 10000-001
2-400 PAGE
2
MAR 01/12
28-12-71

OF NACA INTAKE
RAI 10000-001
3
MAR12

5. REMOVE NACA INTAKE (1).
6. DISCARD SEAL (3).
003
_________________________________
INSTALLATION
OF THE NACA INTAKE
REF. FIG. 281271-RAI-00100
1. CLEAN WORK AREA.
2. APPLY A COAT OF POLYSULFIDE SEALANT
NO. 09-002 (6)
3. PLACE NACA INTAKE.
ALLOW TO POLYMERISE.
4. REMOVE NACA INTAKE.
FLATTEN THE POLYSULFIDE SEALANT (6).
5. APPLY A COAT OF GREASE NO. 04-001 (8) ON
NACA INTAKE BEARING SURFACE.
6. PLACE NACA INTAKE (1) IN RELATION WITH
CENTERING PIN.
7. CLEAN SEAL (3) GROOVE. INSTALL SEAL AND
MAKE CERTAIN THAT SEAL IS IN CORRECT
POSITION.
8. MAKE CERTAIN THAT INDEX (4) AND (5) ARE IN
FACING.
9. INSTALL AND TIGHTEN SCREWS (2).
TIGHTENING TORQUE: BETWEEN 0.8 AND 0.9 M.DAN
(71 AND 80 LBF.INCH).
10.DO A SEAL WITH SEALANT NO. 09-016 (7)
BETWEEN NACA INTAKE AND STRUCURE.ALLOW TO
POLYMERISE
*** CONTINUED ***
AH
28-12-71
RAI 10000-001
2-400 PAGE
3
MAR 01/12
28-12-71

OF NACA INTAKE
004
RAI 10000-001
4
MAR12
_________________
VISUAL
INSPECTION
MAKE CERTAIN THAT THE LOWER SURFACE BASE OF
NACA INTAKE DOES NOT SHOW DEFORMATION OR
CRACK.
*****
AH
E N D
O F
T E X T
*****
28-12-71
RAI 10000-001
2-400 PAGE
4
MAR 01/12
28-12-71
5
AH
NACA INTAKE
RAI 10000-001
MAR12
28-12-71
RAI 10000-001
2-400
PAGE
5
MAR 01/12
28-12-72
OPERATIONAL TEST OF
FLOAT VALVE
OPT 10000-001
1
MAR12
ZONING DATA
___________
ZONE
ACCESS
: 523
623
: 523GT
623GT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
MECHANIC
___
MEN
_________
MAN-HOURS
01
ELAPSED TIME
GSE
PUBLICATION
___________
JIC

AH
57-00-00-OAC-10000
28-12-72
OPT 10000-001
2-400 PAGE
1
MAR 01/12
28-12-72
OPERATIONAL TEST OF
FLOAT VALVE
001
OPT 10000-001
2
MAR12
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
1. MAKE CERTAIN THAT FUEL LEVEL IS BELOW LEVEL
OF VENT FLOW VALVE (PERFORM DEFUELLING OPERATION IF REQUIRED).
2. INSTALL WARNING NOTICE PROHIBING OPERATION
OF FUEL SYSTEM IN FLIGHT COMPARTMENT.
3. INSTALL ACCESS PLATFORM, TO GAIN ACCESS TO
WING TOP SKIN.
4. REMOVE ACCESS DOOR 523GT (623GT) AS FOLLOWS :
*** CONTINUED ***
AH
28-12-72
OPT 10000-001
2-400 PAGE
2
MAR 01/12
28-12-72
OPERATIONAL TEST OF
FLOAT VALVE
003
OPT 10000-001
3
MAR12
_______________________________
OPENING
570000-OAC-10000
004
____________________________
CHECKING
OF VENT FLOAT VALVE
REF. FIG. 281272-RAI-00100
CHECK FREE MOVEMENT OF VALVE BY EXERTING FINGER
PRESSURE ON FLAP (6).
005
________
CLOSE-UP
INSTALL ACCESS DOOR 523GT (623GT) AS FOLLOWS :
006
________________________________
CLOSING
570000-OAC-10000
007
________
CLOSE-UP
6. REMOVE PLATFORM.
*****
AH
E N D
O F
T E X T
*****
28-12-72
OPT 10000-001
2-400 PAGE
3
MAR 01/12
28-12-72
4
AH
VENT FLOAT VALVE
OPT 10000-001
MAR12
28-12-72
OPT 10000-001
2-400
PAGE
4
MAR 01/12
28-12-72

OF VENT FLOAT VALVE
RAI 10000-001
1
MAR12
ZONING DATA
___________
ZONE
ACCESS
: 523
623
: 523GT
623GT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
MECHANIC
_________
MAN-HOURS
01
ELAPSED TIME
GSE
SPARE
: 02 VENT FLOAT VALVE
281270-08-050
EXPENDABLE
: 02 O-RING
02 O-RING
281270-08-030
281270-08-040
BULK MATERIAL : GREASE
04-002
PUBLICATION
___________
JIC

AH
57-00-00-OAC-10000
28-12-72
RAI 10000-001
2-400 PAGE
1
MAR 01/12
28-12-72

OF VENT FLOAT VALVE
001
RAI 10000-001
2
MAR12
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
1. MAKE CERTAIN THAT FUEL LEVEL IS BELOW LEVEL
OF VENT FLOW VALVE (PERFORM DEFUELLING OPERATION IF REQUIRED).
3. INSTALL ACCESS PLATFORM, TO GAIN ACCESS TO
WING TOP SKIN.
4. REMOVE ACCESS DOOR 523GT (623GT) AS FOLLOWS :
*** CONTINUED ***
AH
28-12-72
RAI 10000-001
2-400 PAGE
2
MAR 01/12
28-12-72

OF VENT FLOAT VALVE
003
RAI 10000-001
3
MAR12
_______________________________
OPENING
570000-OAC-10000
004
___________________________
REMOVAL
OF VENT FLOAT VALVE
REF. FIG. 281272-RAI-00100
1. REMOVE SCREWS (4) AND WASHERS (5) RETAINING
VENT FLOAT VALVE.
2. REMOVE VENT FLOAT VALVE (1).
3. REMOVE AND DISCARD VENT FLOAT VALVE
SEALS (2) AND (3).
4. BLANK ORIFICES OF EQUIPMENT.
005
________________________________
INSTALLATION
OF VENT FLOAT VALVE
REF. FIG. 281272-RAI-00100
1. PREPARATION OF REPLACEMENT COMPONENT.
2. CLEAN BONDING PLATE AND APPLY A THIN FILM
OF GREASE.
NOTE:
BEFORE INSTALLATION OF VALVE,CHECK THAT BONDING
STRAP TERMINAL IS PERPENDICULAR TO THE FLOAT
VALVE BODY AXIS,TO AVOID INTERFERENCE BETWEEN
BONDING STRAP AND VALVE BODY.
ADJUST AS NECESSARY.
3. INSTALL NEW SEALS (2) AND (3) (SEALS MUST
BE LUBRICATED WITH CLEAN FUEL).
4. IMMERSE VENT FLOAT VALVE (1) IN CLEAN FUEL.
*** CONTINUED ***
AH
28-12-72
RAI 10000-001
2-400 PAGE
3
MAR 01/12
28-12-72

OF VENT FLOAT VALVE
RAI 10000-001
4
MAR12
5. CLEAN AND INSPECT COMPONENT INSTALLATION

AREA.
6. INSTALL VENT FLOAT VALVE (1).
7. INSTALL SCREWS (4), WASHERS (5) AND TIGHTEN.
006
____________________________
CHECKING
OF VENT FLOAT VALVE
REF. FIG. 281272-RAI-00100
CHECK FREE MOVEMENT OF VALVE BY EXERTING FINGER
PRESSURE ON FLAP (6).
007
________
CLOSE-UP
INSTALL ACCESS DOOR 523GT (623GT) AS FOLLOWS :
008
________________________________
CLOSING
570000-OAC-10000
009
________
CLOSE-UP
6. REMOVE PLATFORM.
*****
AH
E N D
O F
T E X T
*****
28-12-72
RAI 10000-001
2-400 PAGE
4
MAR 01/12
28-12-72
5
AH
VENT FLOAT VALVE
RAI 10000-001
MAR12
28-12-72
RAI 10000-001
2-400
PAGE
5
MAR 01/12
28-20-00
CHECK OF REFUELLING DUCT

FOR NO LEAK OR SEEPAGE
CHK 10010-001
1
APR05
ZONING DATA
___________
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
AH
___
MEN
_________
MAN-HOURS
28-20-00
CHK 10010-001
2-400 PAGE
1
APR 01/05
28-20-00
CHECK OF REFUELLING DUCT

001
CHK 10010-001
2
APR05
_______________________________________________
CHECK
OF REFUELLING DUCT FOR NO LEAK OR SEEPAGE
REF. FIG. 282000-CHK-00110
1. MAKE SURE THAT THE INNER DUCT IS FULL OF
FUEL.
2. CHECK THAT THERE IS NO LEAKAGE OR SEEPAGE AT
THE LEVEL OF DRAIN HOLE (1).
*****
AH
E N D
O F
T E X T
*****
28-20-00
CHK 10010-001
2-400 PAGE
2
APR 01/05
28-20-00
3
AH
REFUELLING DUCT DRAIN
CHK 10010-001
APR05
28-20-00
CHK 10010-001
2-400
PAGE
3
APR 01/05
28-20-00
REMOVAL OF DOUBLE SKIN

CHECK VALVE TO CHECK
CONDITION & CLEANLINESS
CHK 10020-002
1
DEC14
ZONING DATA
___________
ACCESS
: 242AW 242AZ 242BZ 242CW 252AW 252AZ 252BW 252BZ
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
_________
MAN-HOURS
ELAPSED TIME
SPARE
: 01 VALVE
01 SEAL
282520-10
282520-10

OVERHEAD STOWAGE AND
SERVICE COMPARTMENTS
25-24-21-OAC-10000
PUBLICATION
___________
JIC
AH
28-20-00
CHK 10020-002
2-400 PAGE
1
DEC 01/14

001
28-20-00
CHK 10020-002
2
DEC14
___________
PREPARATION
1. OPEN LINING PANELS :
242AW; 252AW; 242CW; 252BW; 242AZ; 252AZ
002
OPENING OF OVERHEAD STOWAGE COMPARTMENTS __________________________________________

IF INSTALLED
____________
252421-OAC-10000
OPEN OVERHEAD STOWAGE COMPARTMENTS MENTIONED
IN ACCESS SECTION OF JOB CARD PAGE 1.
003
____________________________
CHECK
OF SHROUDED PIPE VALVE
REF. FIG. 282000-CHK-00125
1. REMOVAL OF SHROUDED PIPE VALVE :
- REMOVE SCREWS (1), WASHERS (3) AND NUTS
(4),
- REMOVE VALVE (5),
- REMOVE GASKET (2).
2. VISUAL INSPECTION OF SHROUDED PIPE VALVE :
- CHECK CONDITION OF EACH COMPONENT OF THE
VALVE :
. HOUSING (7),
. SPRING (8),
. FLAP (6),
. SEAL (10),
. FLANGE (9).
- CHECK CONDITION OF GASKET (2).
3. CLEAN VALVE COMPONENTS WITH A DRY AND CLEAN
CLOTH OR WITH DRY COMPRESSED AIR.
4. INSTALLATION OF THE SHROUDED PIPE VALVE :
- INSTALL GASKET (2) ON VALVE (5)
- INSTALL VALVE (5) AND ATTACH WITH SCREWS
(1), WASHERS (3) AND NUTS (4). TIGHTEN.
*** CONTINUED ***
AH
28-20-00
CHK 10020-002
2-400 PAGE
2
DEC 01/14
28-20-00

CHK 10020-002
3
DEC14
5. CHECK THAT SHROUDED PIPE VALVE OPERATES

CORRECTLY (BY PRESSING).
004
________
CLOSE-UP
EQUIPMENT.
2. CLOSE LINING PANELS PREVIOUSLY OPENED.
005
CLOSING OF OVERHEAD STOWAGE COMPARTMENTS __________________________________________

IF INSTALLED
____________
252421-OAC-10000
CLOSE OVERHEAD STOWAGE COMPARTMENTS PREVIOUSLY
OPENED.
*****
AH
E N D
O F
T E X T
*****
28-20-00
CHK 10020-002
2-400 PAGE
3
DEC 01/14
28-20-00
4
AH
CHECK OF DOUBLE SKIN

CHECK VALVE
CHK 10020-002
DEC14
28-20-00
CHK 10020-002
2-400
PAGE
4
DEC 01/14
28-20-00
DETAILED VISUAL
INSPECTION OF REFUELLING
DUCT
DVI 10000-002
1
DEC14
ZONING DATA
___________
ACCESS
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
___
MEN
_________
MAN-HOURS
PUBLICATION
___________
JIC

AH
25-24-21-OAC-10000
28-20-00
DVI 10000-002
2-400 PAGE
1
DEC 01/14
28-20-00
DETAILED VISUAL
DUCT
001
DVI 10000-002
2
DEC14
___________
PREPARATION
242AW; 252AW; 242CW; 252BW; 242AZ; 252AZ
002

IF INSTALLED
____________
252421-OAC-10000
003
_____________________________________________
DETAILED
VISUAL INSPECTION OF REFUELLING DUCT
REF. FIG. 282000-DVI-00100
PERFORM A DETAILED VISUAL INSPECTION OF
REFUELLING DUCT (1) CHECKING THAT ITS COMPLETE
SURFACE IS NOT DAMAGED AND FREE FROM FUEL LEAK.
004
________
CLOSE-UP
EQUIPMENT.
005

IF INSTALLED
____________
252421-OAC-10000
OPENED.
*****
AH
E N D
O F
T E X T
*****
28-20-00
DVI 10000-002
2-400 PAGE
2
DEC 01/14
28-20-00
3
AH
REFUELLING DUCT
DVI 10000-002
DEC14
28-20-00
DVI 10000-002
2-400
PAGE
3
DEC 01/14
28-20-00
OPERATIONAL TEST OF
VENTING VALVE
OPT 10010-001
1
DEC14
ZONING DATA
___________
ZONE
ACCESS
: 190
: 192JR 196FS
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
___
MEN
_________
MAN-HOURS
PUBLICATION
___________
JIC
: DC AND AC CONSTANT
FREQUENCY EXTERNAL POWER
SUPPLY
AH
24-46-00-EAD-10000
28-20-00
OPT 10010-001
2-400 PAGE
1
DEC 01/14
28-20-00
OPERATIONAL TEST OF
VENTING VALVE
001
OPT 10010-001
2
DEC14
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
ENERGIZATION OF AIRCRAFT DC AND AC CONSTANT

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
003
___________
PREPARATION
REF.FIG.:121100-FLG-00100
1. PROVIDE FUEL TANKER ACCORDING TO SELECTED
FUEL QUANTITY.
MAXIMUM PRESSURE: 3.5 BARS (50 PSI).
2. OPEN REFUEL/DEFUEL DOOR 196FS.
*** CONTINUED ***
AH
28-20-00
OPT 10010-001
2-400 PAGE
2
DEC 01/14
28-20-00
OPERATIONAL TEST OF
VENTING VALVE
OPT 10010-001
3
DEC14
3. OPEN REFUEL/DEFUEL PANEL DOOR 192JR.

4. CONNECT FUEL TANKER COUPLING SLEEVE TO
REFUEL/DEFUEL COUPLING.
PERFORM EQUIPOTENTIEL CONNECTION BETWEEN
FUEL TANKER AND A/C USING THE GROUND
CONNECTION ON RIGHT M.L.G.
004
_________________________________
OPERATIONAL
TEST OF VENTING VALVE
REF. FIG. 282000-OPT-00120
NOTE : THIS TEST WILL BE PERFORMED DURING A
REFUELING OR A REPLENISHING (JIC 121100FLG-10020).
1. ON TANKER, STOP REFUELING OR REPLENISHING.
2. PLACE TANKER IN SUCTION FUNCTION
WARNING : MAXIMUM SUCTION IS 0,770 BARS
(11PSI).
3. ON PANEL 5004VU :
A. REFUELING/REFUEL/OFF/DEFUEL SWITCH
ON OFF POSITION.
B. PLACE SURGE/VALVE SWITCH ON OPEN
POSITION.
C. REFUEL/VALVES SWITCHES BEING ON NORM
POSITION.
4. PERFORM SUCTION AT THE TANKER.
5. WHEN FLOW IS AT ZERO, STOP THE SUCTION.
6. ON PANEL 5004VU,
PLACE SURGE/VALVE SWITCH ON SHUT
POSITION.
*** CONTINUED ***
AH
28-20-00
OPT 10010-001
2-400 PAGE
3
DEC 01/14
28-20-00
OPERATIONAL TEST OF
VENTING VALVE
005
OPT 10010-001
4
DEC14
DE-ENERGIZATION OF AIRCRAFT DC AND AC CONSTANT

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
006
________
CLOSE-UP
1. DISCONNECT COUPLING (IF TRANSFER PERFORMED).
2. DISCONNECT EQUIPOTENTIAL CONNECTION BETWEEN
THE TANKER AND THE AIRCRAFT (IF REQUIRED).
3. CLOSE REFUEL/DEFUEL DOOR 196FS (EVENTUALLY).
4. CLOSE REFUELING PANEL DOOR 192JR (EVENTUALLY).
5. REMOVE FUEL TANKER FROM WORKING AREA (IF
USED).
EQUIPMENT.
*****
AH
E N D
O F
T E X T
*****
28-20-00
OPT 10010-001
2-400 PAGE
4
DEC 01/14
28-20-00
5
AH
PIPE DRAINING
OPT 10010-001
DEC14
28-20-00
OPT 10010-001
2-400
PAGE
5
DEC 01/14
28-20-00
OPERATIONAL TEST OF
VENTING VALVE
OPT 10010-002
1
DEC14
ZONING DATA
___________
ZONE
ACCESS
: 190
: 192JR 196FS
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
___
MEN
_________
MAN-HOURS
PUBLICATION
___________
JIC
SUPPLY
AH
24-46-00-EAD-10000
28-20-00
OPT 10010-002
2-400 PAGE
1
DEC 01/14
28-20-00
OPERATIONAL TEST OF
VENTING VALVE
001
OPT 10010-002
2
DEC14
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
003
___________
PREPARATION
REF.FIG.:121100-FLG-00100
1. PROVIDE FUEL TANKER ACCORDING TO SELECTED
FUEL QUANTITY.
MAXIMUM PRESSURE: 3.5 BARS (50 PSI).
2. OPEN REFUEL/DEFUEL DOOR 196FS.
*** CONTINUED ***
AH
28-20-00
OPT 10010-002
2-400 PAGE
2
DEC 01/14
28-20-00
OPERATIONAL TEST OF
VENTING VALVE
OPT 10010-002
3
DEC14
3. OPEN REFUEL/DEFUEL PANEL DOOR 192JR.

4. CONNECT FUEL TANKER COUPLING SLEEVE TO
REFUEL/DEFUEL COUPLING.
PERFORM EQUIPOTENTIEL CONNECTION BETWEEN
FUEL TANKER AND A/C USING THE GROUND
CONNECTION ON RIGHT M.L.G.
004
_________________________________
OPERATIONAL
TEST OF VENTING VALVE
REF. FIG. 282000-OPT-00120
NOTE : THIS TEST WILL BE PERFORMED DURING A
REFUELING OR A REPLENISHING (JIC 121100FLG-10020).
1. ON TANKER, STOP REFUELING OR REPLENISHING.
2. PLACE TANKER IN SUCTION FUNCTION
WARNING : MAXIMUM SUCTION IS 0,770 BARS
(11PSI).
3. ON PANEL 100QU :
A. REFUELING/REFUEL/OFF/DEFUEL SWITCH
ON OFF POSITION.
B. PLACE SURGE/VALVE SWITCH ON OPEN
POSITION.
C. REFUEL/VALVES SWITCHES BEING ON NORM
POSITION.
4. PERFORM SUCTION AT THE TANKER.
5. WHEN FLOW IS AT ZERO, STOP THE SUCTION.
6. ON PANEL 100QU,
PLACE SURGE/VALVE SWITCH ON SHUT
POSITION.
*** CONTINUED ***
AH
28-20-00
OPT 10010-002
2-400 PAGE
3
DEC 01/14
28-20-00
OPERATIONAL TEST OF
VENTING VALVE
005
OPT 10010-002
4
DEC14

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
006
________
CLOSE-UP
USED).
EQUIPMENT.
*****
AH
E N D
O F
T E X T
*****
28-20-00
OPT 10010-002
2-400 PAGE
4
DEC 01/14
28-20-00
5
AH
PIPE DRAINING
OPT 10010-002
DEC14
28-20-00
OPT 10010-002
2-400
PAGE
5
DEC 01/14
28-20-00
OPERATIONAL TEST OF
DOUBLE SKIN FOR FREEDOM
OF AIRSTREM
OPT 10020-002
1
DEC14
ZONING DATA
___________
ACCESS
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
: 01 PRESSURIZED AIR SOURCE
_________
MAN-HOURS
PUBLICATION
___________
JIC

AH
25-24-21-OAC-10000
28-20-00
OPT 10020-002
2-400 PAGE
1
DEC 01/14
28-20-00
OPERATIONAL TEST OF
OF AIRSTREM
001
OPT 10020-002
2
DEC14
___________
PREPARATION
242AW; 252AW; 242CW; 252BW; 242AZ; 252AZ
002

IF INSTALLED
____________
252421-OAC-10000
003
_____________________________________________
CHECK
OF SHROUDED PIPE FOR FREEDOM OF AIRFLOW
REF. FIG. 282000-CHK-00120
1. PRESS AND LIFT THE FLAP OF THE SHROUDED PIPE
VALVE.
2. PLACE THE END OF THE AIR SUPPLY HOSE UNDER
THE VALVE AND APPLY A PRESSURE OF:
340 MBAR (5 PSI).
3. CHECK THAT AIR FLOWS THROUGH THE DRAIN PORT
ON RIGHT MAIN LANDING GEAR FAIRING.
4. CUT OFF AIR SUPPLY.
5. RELEASE THE FLAP OF THE SHROUDED PIPE VALVE.
004
________
CLOSE-UP
EQUIPMENT.
*** CONTINUED ***

AH
28-20-00
OPT 10020-002
2-400 PAGE
2
DEC 01/14
28-20-00
OPERATIONAL TEST OF
OF AIRSTREM
005
OPT 10020-002
3
DEC14

IF INSTALLED
____________
252421-OAC-10000
OPENED.
*****
AH
E N D
O F
T E X T
*****
28-20-00
OPT 10020-002
2-400 PAGE
3
DEC 01/14
28-20-00
4
AH
DOUBLE SKIN PIPING OF

REFUELING/DEFUELING
OPT 10020-002
DEC14
28-20-00
OPT 10020-002
2-400
PAGE
4
DEC 01/14
28-20-00
OPERATIONAL TEST OF L/R

FEEDER TANK JET PUMP
MONITORING THROUGH MFC
OPT 10030-002
1
DEC14
ZONING DATA
___________
ZONE
ACCESS
: 510
610
: 511
611
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
_________
MAN-HOURS
PUBLICATION
___________
JIC
JIC
JIC

SUPPLY
: READING OF MFC
MAINTENANCE MEMORY
: ERASURE OF MFC
MAINTENANCE MEMORY
AH
24-40-00-EAD-10000
45-13-00-RDG-10000
45-13-00-RON-10000
28-20-00
OPT 10030-002
2-400 PAGE
1
DEC 01/14
28-20-00

001
OPT 10030-002
2
DEC14
___________________________________________
ENERGIZATION
244000-EAD-10000
002
___________
PREPARATION
1. ON PANEL 4VU :
ON FUEL QUANTITY INDICATOR, CHECK THAT EACH
TANK CONTAINS AT LEAST 500 KG (1102 LBS).
NOTE :1. IF NECESSARY FILL THE TANKS.
2. DO NOT FILL THE TANKS TO HIGH
LEVEL STOP.
2. ON THE ELECTRONIC RACK 90VU:
- REMOVE THE PANEL 222AZ TO HAVE ACCES TO
962VU
- OPEN THE PANEL 121VU TO HAVE ACCES TO
910VU.
003
_________________________________________
READING
THE MAINTENANCE MEMORY OF THE MFC
USING THE PROCEDURE GIVEN BELOW MAKE SURE THAT
THE FAILURES :
- ENGINE 1 FEEDER JET PUMP FAULT
ARE NOT RECORDED IN THE MAINTENANCE MEMORY OF
THE MFC.
004
_________________________________
READING
OF MFC MAINTENANCE MEMORY
451300-RDG-10000
*** CONTINUED ***

AH
28-20-00
OPT 10030-002
2-400 PAGE
2
DEC 01/14
28-20-00

005
OPT 10030-002
3
DEC14
OPERATIONAL TEST OF FEEDER TANK

_______________________________
JET PUMP MONITORING
___________________
REF. FIG. 282000-OPT-00100
1. ON PANEL 4VU :
MAKE SURE THAT THE LO LVL INDICATORS LIGHT
OF FUEL QUANTITY INDICATOR (3QT) ARE OFF.
2. ON PANEL 25VU, MAKE SURE THAT THE FUEL X
FEED FLOWBAR IS CROSS LINE (DISCONTINUITY).
3. REMOVE RELAYS
155QA ON 962VU
154QA ON 910VU
4. ON PANEL 25VU :
- PRESS FUEL/ENG 1/PUMP AND FUEL/ENG 2/
PUMP PUSHBUTTONS SWITCHES.
- MAKE CERTAIN THAT :
. RUN LEGENDS ARE OFF
. OFF LEGENDS ARE OFF
. FEED LOW PRESS LEGENDS REMAIN ON.
5. TEN MINUTES AFTER THESE OPERATIONS EXECUTED,
READ MFC MEMORY AS FOLLOW:
006
___________
PREPARATION
THE FAILURES :
ARE RECORDED IN THE MAINTENANCE MEMORY OF THE
MFC.
*** CONTINUED ***

AH
28-20-00
OPT 10030-002
2-400 PAGE
3
DEC 01/14
28-20-00

007
OPT 10030-002
4
DEC14
_________________________________
READING
451300-RDG-10000
008
_________________________________
ERASURE
451300-RON-10000
009
________
CLOSE-UP
1. ON 962VU (910VU), INSTALL RELAY 155QA
(154QA).
INSTALL THE CORRESPONDING PANELS.
2. ON PANEL 25VU :
-RELEASE FUEL/ENG1/PUMP (FUEL/ENG2/PUMP)
PUSBUTTON SWITCH:
-CHECK THAT:
. RUN LEGEND IS OFF
. OFF LEGEND IS ON.
3. PRESSURIZATION OF FUEL SYSTEM
ON OVERHEAD PANEL 25VU:
-PRESS P/BSW FUEL/ENG1 (2)/PUMP
(ELECTRIC PUMP OPERATING)
.RUN LEGEND ON
.OFF LEGEND OFF.
-CHECK THAT FUEL/ENG1 (2)/FEED LO PR
CAUTION LIGHT IS OFF
NOTE: WHEN SYSTEM IS PRESSURIZED, FUEL FEED
LOW PRESSURE SWITCH 13QA (14QA)
DE-ENERGIZES FUEL/FEED LO PR CAUTION
LIGHT.
*** CONTINUED ***
AH
28-20-00
OPT 10030-002
2-400 PAGE
4
DEC 01/14
28-20-00

OPT 10030-002
5
DEC14
4. SYSTEM PRESSURIZATION SHUT DOWN

RELEASE P/BSW FUEL/ENG1 (2)/PUMP:
.RUN LEGEND OFF
.OFF LEGEND ON
.FUEL/ENG1 (2)/FEED LO PR CAUTION LIGHTS
ON.
010
______________________________________________
DE-ENERGIZATION
244000-EAD-10000
011
________
CLOSE-UP
1. MAKE CERTAIN THAT WORKING AREA IS CLEAN.
2. INSTALL PANELS IF THEY HAVE BEEN REMOVED
EVENTUALLY.
*****
AH
E N D
O F
T E X T
*****
28-20-00
OPT 10030-002
2-400 PAGE
5
DEC 01/14
28-20-00
6
AH
FEEDER JET PUMP SYSTEM
OPT 10030-002
DEC14
28-20-00
OPT 10030-002
2-400
PAGE
6
DEC 01/14
28-20-00

OPT 10030-003
1
DEC14
ZONING DATA
___________
ZONE
ACCESS
: 510
610
: 511
611
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
_________
MAN-HOURS
PUBLICATION
___________
JIC
JIC
JIC
JIC
: PRINCIPLE OF CDS USE

(DISPLAY UNITS
EXPLORATION)
SUPPLY
: READING OF MFC
MAINTENANCE MEMORY
: ERASURE OF MFC
MAINTENANCE MEMORY
AH
31-63-00-PRO-10000
24-40-00-EAD-10000
45-13-00-RDG-10000
45-13-00-RON-10000
28-20-00
OPT 10030-003
2-400 PAGE
1
DEC 01/14
28-20-00

001
OPT 10030-003
2
DEC14
PRINCIPLE OF CDS USE (DISPLAY UNITS

___________________________________
EXPLORATION)
____________
(TO USE ONLY IF NEEDED)
_______________________
316300-PRO-10000
NOTE: PROCEDURE TO USE ONLY IF NEEDED.
THIS PROCEDURE DESCRIBES LOCATION AND
MANAGEMENT OF THE DIFFERENT DISPLAY
WINDOWS PROVIDED BY THE THREE FORMATS
(PFD, EWD, MFD) PROPOSED ON THE FIVE
DISPLAY UNITS (DU).
002
___________________________________________
ENERGIZATION
244000-EAD-10000
003
___________
PREPARATION
1. ON MFD UPPER WINDOW, IN ENGINE SD PAGE,
CHECK THAT EACH TANK CONTAINS AT LEAST
500 KG (1102 LBS).
NOTE :1. IF NECESSARY FILL THE TANKS.
2. DO NOT FILL THE TANKS TO HIGH
LEVEL STOP.
962VU
- OPEN THE PANEL 121VU TO HAVE ACCES TO
910VU.
004
_________________________________________
READING
THE MAINTENANCE MEMORY OF THE MFC
THE FAILURES :
*** CONTINUED ***
AH
28-20-00
OPT 10030-003
2-400 PAGE
2
DEC 01/14
28-20-00

OPT 10030-003
3
DEC14

ARE NOT RECORDED IN THE MAINTENANCE MEMORY OF
THE MFC.
005
_________________________________
READING
451300-RDG-10000
006
OPERATIONAL TEST OF FEEDER TANK

_______________________________
JET PUMP MONITORING
___________________
REF. FIG. 282000-OPT-00100
1. ON EWD, IN ALERT WINDOW, MAKE SURE THAT
FUEL LO LVL MESSAGE IS NOT DISPLAYED.
2. ON PANEL 25VU, MAKE SURE THAT THE FUEL X
FEED FLOWBAR IS CROSS LINE (DISCONTINUITY).
ON MFD UPPER WINDOW, IN ENGINE SD PAGE, MAKE
SURE THAT THE FUEL X FEED FLOWBAR IS
CROSSLINE.
3. REMOVE RELAYS
155QA ON 962VU
154QA ON 910VU
4. ON PANEL 25VU :
- PRESS FUEL/ENG 1/PUMP AND FUEL/ENG 2/
PUMP PUSHBUTTONS SWITCHES.
- MAKE CERTAIN THAT :
. RUN LEGENDS ARE OFF
. OFF LEGENDS ARE OFF
. FEED LOW PRESS LEGENDS REMAIN ON.
ON MFD UPPER WINDOW, IN ENGINE SD PAGE, MAKE
CERTAIN THAT FEED LO PR MESSAGE REMAIN
DISPLAYED.
5. TEN MINUTES AFTER THESE OPERATIONS EXECUTED,
*** CONTINUED ***
AH
28-20-00
OPT 10030-003
2-400 PAGE
3
DEC 01/14
28-20-00

OPT 10030-003
4
DEC14
READ MFC MEMORY AS FOLLOW:

007
___________
PREPARATION
THE FAILURES :
ARE RECORDED IN THE MAINTENANCE MEMORY OF THE
MFC.
008
_________________________________
READING
451300-RDG-10000
009
_________________________________
ERASURE
451300-RON-10000
010
________
CLOSE-UP
1. ON 962VU (910VU), INSTALL RELAY 155QA
(154QA).
2. ON PANEL 25VU :
-RELEASE FUEL/ENG1/PUMP (FUEL/ENG2/PUMP)
PUSBUTTON SWITCH:
-CHECK THAT:
. RUN LEGEND IS OFF
. OFF LEGEND IS ON.
ON MFD UPPER WINDOW, IN ENGINE SD PAGE,
PUMP LEGENDS ARE OFF.
*** CONTINUED ***
AH
28-20-00
OPT 10030-003
2-400 PAGE
4
DEC 01/14
28-20-00

OPT 10030-003
5
DEC14
3. PRESSURIZATION OF FUEL SYSTEM

ON OVERHEAD PANEL 25VU:
-PRESS P/BSW FUEL/ENG1 (2)/PUMP
.RUN LEGEND ON
.OFF LEGEND OFF.
-CHECK THAT FUEL/ENG1 (2)/FEED LO PR
CAUTION LIGHT IS OFF
ON MFD UPPER WINDOW, IN ENGINE SD PAGE:
- FEED LO PR MESSAGE IS NOT DISPLAYED
- PUMP LEGENDS ARE ON.
NOTE: WHEN SYSTEM IS PRESSURIZED, FUEL FEED
LOW PRESSURE SWITCH 13QA (14QA)
DE-ENERGIZES FUEL/FEED LO PR CAUTION
LIGHT.
RELEASE P/BSW FUEL/ENG1 (2)/PUMP:
- ON PANEL 25VU:
.RUN LEGEND OFF
.OFF LEGEND ON
.FUEL/ENG1 (2)/FEED LO PR CAUTION LIGHTS
ON.
- ON MFD UPPER WINDOW, IN ENGINE SD PAGE:
. FEED LO PR MESSAGE IS DISPLAYED
. PUMP LEGENDS ARE OFF.
011
______________________________________________
DE-ENERGIZATION
244000-EAD-10000
012
________
CLOSE-UP
*** CONTINUED ***
AH
28-20-00
OPT 10030-003
2-400 PAGE
5
DEC 01/14
28-20-00

OPT 10030-003
6
DEC14
2. INSTALL PANELS IF THEY HAVE BEEN REMOVED

EVENTUALLY.
*****
AH
E N D
O F
T E X T
*****
28-20-00
OPT 10030-003
2-400 PAGE
6
DEC 01/14
28-20-00
7
AH
OPT 10030-003
DEC14
28-20-00
OPT 10030-003
2-400
PAGE
7
DEC 01/14
28-21-00
OPERATIONAL TEST OF
FEED LO PRESS
INDICATING SYSTEM
OPT 10000-001
1
DEC14
ZONING DATA
___________
ZONE
: 210
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
___
MEN
_________
MAN-HOURS
PUBLICATION
___________
JIC

SUPPLY
AH
24-40-00-EAD-10000
28-21-00
OPT 10000-001
2-400 PAGE
1
DEC 01/14
28-21-00
OPERATIONAL TEST OF
FEED LO PRESS
INDICATING SYSTEM
001
OPT 10000-001
2
DEC14
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________________________________________
ENERGIZATION
244000-EAD-10000
003
__________________________
PREPARATION
OF FUEL SYSTEM
1. ON PANEL 4VU,
TANK CONTAINS 500KG (1102LBS) FUEL MINIMUM.
NOTE : IF REQUIRED, TOP UP TANKS
(J.I.C 121100-FLG-1XXXXX).
*** CONTINUED ***

AH
28-21-00
OPT 10000-001
2-400 PAGE
2
DEC 01/14
28-21-00
OPERATIONAL TEST OF
FEED LO PRESS
INDICATING SYSTEM
004
OPT 10000-001
3
DEC14
_______________________________
OPERATIONAL
TEST OF FUEL SYSTEM
REF. FIG. 282100-OPT-00120
1. AIRCRAFT ON GROUND AND ENERGIZED.
ON OVERHEAD PANEL 25VU :
A. P/BSW FUEL/ENG1(2)/PUMP RELEASED
(ELECTRIC PUMP SHUT DOWN)
- RUN LEGEND OFF
- OFF LEGEND ON.
B. FUEL/X FEED PUSHBUTTON SWITCH RELEASED
(CROSSFEED VALVE CLOSED)
- CROSS LINE FLOWBAR (VERTICAL) IS ON.
- ON PANEL 4VU, FUEL/X FEED LEGEND IS
OFF.
C. ON FUEL/ENG1/(2) LP VALVE ANNUNCIATOR
(FUEL LP VALVE OPEN).
- FLOWBAR IS ON.
D. FUEL/ENG1(2)/FEED LO PR CAUTION LIGHTS
ON
- SYSTEM DEPRESSURIZED.
2. PRESSURIZATION OF SYSTEM
A. PRESS P/BSW FUEL/ENG1(2)/PUMP
- RUN LEGEND ON
- OFF LEGEND OFF.
B. CHECK THAT FUEL/ENG1(2)/FEED LO PR
CAUTION LIGHT IS OFF.
NOTE : WHEN SYSTEM IS PRESSURIZED,
FUEL FEED LOW PRESSURE
*** CONTINUED ***
AH
28-21-00
OPT 10000-001
2-400 PAGE
3
DEC 01/14
28-21-00
OPERATIONAL TEST OF
FEED LO PRESS
INDICATING SYSTEM
OPT 10000-001
4
DEC14
SWITCH DE-ENERGIZES
FUEL/FEED LO PR CAUTION LIGHT.
RELEASE P/BSW FUEL/ENG1(2)/PUMP
- RUN LEGEND OFF.
- OFF LEGEND ON.
- FUEL/ENG1(2) FEED LOW PR CAUTION LIGHT ON.
NOTE: }FEED LOW PRESS} CAUTION LIGHT WILL
REMAIN EXTINGUISHED UNTIL THE FUEL
PRESSURE DROPS BELOW THE TRIGGERING
THRESHOLD.
THERE IS NO REQUIREMENT ON DELAY FOR
}FEED LOW PRESS}CAUTION LIGHT COMES
ILLUMINATED AFTER P/B SW RELEASE.
FOR A QUICK FUEL SYSTEM VERIFICATION:
- RESET C/B FUEL FEED/ENG1(ENG2)
RESETTING C/B ENSURES THAT THE FUEL SYSTEM
IS QUICKLY DEPRESSURIZED THROUGH THE
}MOTIVE FLOW VALVE}.
4. CHECK AFTER ENGINE START
NOTE : THIS CHECK WILL BE PERFORMED DURING
ENGINE RUN UP.
AFTER ENGINE START
- RUN LEGEND OFF
- OFF LEGEND OFF.
ELECTRIC PUMP IS SHUT DOWN AFTER STARTING
OF MOTOR BY MEANS OF PRESSURE SWITCH
INSTALLED AT OUTLET OF ENGINE
FEEDER TANK JET PUMP.
- FUEL/ENG1(2)/FEED LO PR CAUTION LIGHT OFF.
SYSTEM PRESSURIZED.
*** CONTINUED ***

AH
28-21-00
OPT 10000-001
2-400 PAGE
4
DEC 01/14
28-21-00
OPERATIONAL TEST OF
FEED LO PRESS
INDICATING SYSTEM
005
OPT 10000-001
5
DEC14
______________________________________________
DE-ENERGIZATION
244000-EAD-10000
006
_______________________
CLOSE-UP
OF FUEL SYSTEM
EQUIPMENT.
2. DISCONNECT AIRCRAFT FROM GROUND.
5. REMOVE ACCESS PLATFORM,(IF NECESSARY).
*****
AH
E N D
O F
T E X T
*****
28-21-00
OPT 10000-001
2-400 PAGE
5
DEC 01/14
28-21-00
6
AH
FUEL DISTRIBUTION
OPERATIONAL TEST
OPT 10000-001
DEC14
28-21-00
OPT 10000-001
2-400
PAGE
6
DEC 01/14
28-21-00
OPERATIONAL TEST OF
FEED LO PRESS
INDICATING SYSTEM
OPT 10000-002
1
DEC14
ZONING DATA
___________
ZONE
: 210
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
___
MEN
_________
MAN-HOURS
PUBLICATION
___________
JIC
JIC

(DISPLAY UNITS
EXPLORATION)
SUPPLY
AH
31-63-00-PRO-10000
24-40-00-EAD-10000
28-21-00
OPT 10000-002
2-400 PAGE
1
DEC 01/14
28-21-00
OPERATIONAL TEST OF
FEED LO PRESS
INDICATING SYSTEM
001
OPT 10000-002
2
DEC14

___________________________________
EXPLORATION)
____________
_______________________
316300-PRO-10000
DISPLAY UNITS (DU).
002
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
*** CONTINUED ***

AH
28-21-00
OPT 10000-002
2-400 PAGE
2
DEC 01/14
28-21-00
OPERATIONAL TEST OF
FEED LO PRESS
INDICATING SYSTEM
003
OPT 10000-002
3
DEC14
___________________________________________
ENERGIZATION
244000-EAD-10000
004
__________________________
PREPARATION
OF FUEL SYSTEM
CHECK THAT EACH TANK CONTAINS 500KG
(1102LBS) FUEL MINIMUM.
NOTE : IF REQUIRED, TOP UP TANKS
(J.I.C 121100-FLG-1XXXXX).
005
_______________________________
OPERATIONAL
TEST OF FUEL SYSTEM
REF. FIG. 282100-OPT-00120
REF. FIG. 282000-OPT-00130
1. AIRCRAFT ON GROUND AND ENERGIZED.
A. - ON OVERHEAD PANEL 25VU:
P/BSW FUEL/ENG1(2)/PUMP RELEASED
. RUN LEGEND OFF
. OFF LEGEND ON.
- ON MFD UPPER WINDOW, IN ENGINE SD PAGE,
CHECK THAT ITEM 1 IS DISPLAYED FOR
ENGINE 1(2).
B. - ON OVERHEAD PANEL 25VU:
FUEL/X FEED PUSHBUTTON SWITCH
RELEASED (CROSSFEED VALVE CLOSED)
. CROSS LINE FLOWBAR (VERTICAL) IS ON.
- ON PANEL 4VU, FUEL/X FEED LEGEND IS
OFF.
. ITEM 7 IS DISPLAYED,
. CROSS LINE FLOWBAR (VERTICAL) APPEARS
C. - ON OVERHEAD PANEL 25VU:
ON FUEL/ENG1/(2) LP VALVE ANNUNCIATOR
*** CONTINUED ***
AH
28-21-00
OPT 10000-002
2-400 PAGE
3
DEC 01/14
28-21-00
OPERATIONAL TEST OF
FEED LO PRESS
INDICATING SYSTEM
OPT 10000-002
4
DEC14
(FUEL LP VALVE OPEN).

. FLOWBAR IS ON.
. ITEM 9 IS DISPLAYED FOR ENGINE 1(2)
. FLOWBAR IN LINE.
D. - ON OVERHEAD PANEL 25VU:
FUEL/ENG1(2)/FEED LO PR CAUTION
LIGHTS ON
AMBER FEED LO PR MESSAGE IS DISPLAYED
FOR ENGINE 1(2)
- ON EWD, IN ALERT WINDOW, FUEL FEED LO
PR MESSAGE APPEARS
- MASTER CAUTION LIGHTS FLASH
- SINGLE CHIME
- SYSTEM DEPRESSURIZED.
2. PRESSURIZATION OF SYSTEM
A. - ON OVERHEAD PANEL 25VU:
- PRESS P/BSW FUEL/ENG1(2)/PUMP
. RUN LEGEND ON
. OFF LEGEND OFF.
ITEM 2 IS DISPLAYED FOR ENGINE 1(2).
B. - ON OVERHEAD PANEL 25VU:
CHECK THAT FUEL/ENG1(2)/FEED LO PR
CAUTION LIGHT IS OFF.
FEED LO PR MESSAGE DISAPPEARS
PR MESSAGE DISAPPEARS.
NOTE : WHEN SYSTEM IS PRESSURIZED,
SWITCH DE-ENERGIZES
FUEL/FEED LO PR CAUTION LIGHT.
*** CONTINUED ***
AH
28-21-00
OPT 10000-002
2-400 PAGE
4
DEC 01/14
OPERATIONAL TEST OF
FEED LO PRESS
INDICATING SYSTEM
28-21-00
OPT 10000-002
5
DEC14
- RELEASE P/BSW FUEL/ENG1(2)/PUMP

. RUN LEGEND OFF.
. OFF LEGEND ON.
. ITEM 1 IS DISPLAYED.
. FEED LO PR MESSAGE IS DISPLAYED FOR
ENGINE 1(2)
- FUEL/ENG1(2) FEED LOW PR CAUTION LIGHT ON.
- ON EWD, IN ALERT WINDOW, FUEL FEED LO PR
MESSAGE APPEARS
- SINGLE CAUTION
REMAIN EXTINGUISHED UNTIL THE FUEL
THRESHOLD.
THERE IS NO REQUIREMENT ON DELAY FOR
}FEED LOW PRESS}CAUTION LIGHT COMES
FOR A QUICK FUEL SYSTEM VERIFICATION:
- RESET C/B FUEL FEED/ENG1(ENG2)
RESETTING C/B ENSURES THAT THE FUEL SYSTEM
IS QUICKLY DEPRESSURIZED THROUGH THE
}MOTIVE FLOW VALVE}.
4. CHECK AFTER ENGINE START
NOTE : THIS CHECK WILL BE PERFORMED DURING
ENGINE RUN UP.
AFTER ENGINE START
- ON OVERHEAD PANEL 25VU :
. RUN LEGEND OFF
. OFF LEGEND OFF.
ITEM 3 IS DISPLAYED.
ELECTRIC PUMP IS SHUT DOWN AFTER STARTING
OF MOTOR BY MEANS OF PRESSURE SWITCH
INSTALLED AT OUTLET OF ENGINE
*** CONTINUED ***
AH
28-21-00
OPT 10000-002
2-400 PAGE
5
DEC 01/14
28-21-00
OPERATIONAL TEST OF
FEED LO PRESS
INDICATING SYSTEM
OPT 10000-002
6
DEC14
- ON OVERHEAD PANEL 25VU:

. FUEL/ENG1(2)/FEED LO PR CAUTION LIGHT
OFF.
FEED LO PR MESSAGE DISAPPEARS
- ON EWD, IN ALERT WINDOW, FUEL FEED LO PR
MESSAGE DISAPPEARS.
SYSTEM PRESSURIZED.
006
______________________________________________
DE-ENERGIZATION
244000-EAD-10000
007
_______________________
CLOSE-UP
OF FUEL SYSTEM
EQUIPMENT.
*****
AH
E N D
O F
T E X T
*****
28-21-00
OPT 10000-002
2-400 PAGE
6
DEC 01/14
28-21-00
7
AH
FUEL DISTRIBUTION
OPERATIONAL TEST
OPT 10000-002
DEC14
28-21-00
OPT 10000-002
2-400
PAGE
7
DEC 01/14
28-21-00
8
AH
FUEL DISTRIBUTION
LEGEND
OPT 10000-002
DEC14
28-21-00
OPT 10000-002
2-400
PAGE
8
DEC 01/14
28-21-61
REMOVAL/INSTALLATION OF
SWITCH
RAI 10000-001
1
MAR15
ZONING DATA
___________
ZONE
ACCESS
: 475
485
: 475AT 485AT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
_________
MAN-HOURS
ELAPSED TIME
GSE
: 01 ACCESS PLATFORM 4M (13FT)
SPARE
: 02 FUEL FEED LOW PRES SWITCH
282160-01-020
EXPENDABLE
: 02 SEAL
282160-01-010
: REMOVAL/INSTALLATION OF
COWLS ATTACHED BY BOLTS
: OPERATIONAL TEST OF FUEL
SYSTEM
54-00-00-RAI-10000
PUBLICATION
___________
JIC
JIC
AH
28-21-00-OPT-10000
28-21-61
RAI 10000-001
2-400 PAGE
1
MAR 01/15
28-21-61
SWITCH
001
RAI 10000-001
2
MAR15
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
1. POSITION A 4M (13FT.) ACCESS PLATFORM TO
GAIN ACCESS TO ENGINE.
2. MAKE CERTAIN THAT ENG1 (ENG2) FUEL LP VALVES
9QG (10QG) ARE CLOSED.
3. DISPLAY A WARNING NOTICE IN FLIGHT COMPARTMENT TO PROHIBIT ENERGIZATION OF FUEL
SYSTEM.
4. ON PANEL 121VU,
OPEN, SAFETY AND TAG THE FOLLOWING CIRCUIT
BREAKERS :
*** CONTINUED ***
AH
28-21-61
RAI 10000-001
2-400 PAGE
2
MAR 01/15
28-21-61
SWITCH
RAI 10000-001
3
MAR15
1QG(2QG) FUEL/LP VALVES/ENG1(2)/MOTOR1

5QG(6QG) FUEL/LP VALVES/ENG1(2)/IND
5. REMOVE ACCESS COWL 475AT(485AT) AS FOLLOWS :
003
____________________________________________
REMOVAL
OF AFT UPPER COWL ATTACHED BY BOLTS.
540000-RAI-10000
004
________________________________________
REMOVAL
OF FUEL FEED LOW PRESSURE SWITCH
REF. FIG. 282161-RAI-00100
1. DISCONNECT ELECTRICAL CONNECTOR (9).
2. REMOVE FUEL FEED LOW PRESSURE SWITCH (8).
3. REMOVE AND DISCARD SEAL (7).
4. BLANK ORIFICES AND CONNECTOR OF REMOVED
EQUIPMENT.
005
INSTALLATION OF FUEL FEED LOW PRESSURE

______________________________________
SWITCH
______
REF. FIG. 282161-RAI-00100
1. REMOVE BLANKING CAPS.
2. INSTALL NEW SEAL (7) (SEAL MUST BE PREVIOUSLY LUBRICATED WITH CLEAN FUEL).
3. INSTALL FUEL FEED LOW PRESSURE SWITCH (8),
AND HANDTIGHTEN UNTIL SWITCH BEARS TIGHTLY
ON PAD.
4. CONNECT ELECTRICAL CONNECTOR (9).
*** CONTINUED ***

AH
28-21-61
RAI 10000-001
2-400 PAGE
3
MAR 01/15
28-21-61
SWITCH
006
RAI 10000-001
4
MAR15
________
CLOSE-UP
1. ON PANEL 121VU,
REMOVE SAFETY CLIPS AND CLOSE THE FOLLOWING
CIRCUIT BREAKERS :
1QG (2QG), 3QG (4QG), (5QG) AND (6QG).
2. CLOSE ACCESS COWL 475AT(485AT) AS FOLLOWS :
007
INSTALLATION OF AFT UPPER COWL ATTACHED

_______________________________________
BY BOLTS
________
540000-RAI-10000
008
________
CLOSE-UP
6. REMOVE PLATFORM.
009
R
_______________________________
OPERATIONAL
TEST OF FUEL SYSTEM
282100-OPT-10000
*****
AH
E N D
O F
T E X T
*****
28-21-61
RAI 10000-001
2-400 PAGE
4
MAR 01/15
28-21-61
5
AH
FUEL LP VALVE
RAI 10000-001
MAR15
28-21-61
RAI 10000-001
2-400
PAGE
5
MAR 01/15
28-21-71
DETAILED VISUAL
INSPECTION OF FUEL PUMP
HARNESS
DVI 10000-001
1
MAR15
ZONING DATA
___________
ZONE
ACCESS
: 293
294
522
622
: 293BL 294BR
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
_________
MAN-HOURS
PUBLICATION
___________
JIC

OF WING-TO-FUSELAGE
FAIRINGS
AH
53-93-00-RAI-10000
28-21-71
DVI 10000-001
2-400 PAGE
1
MAR 01/15
28-21-71
DETAILED VISUAL
HARNESS
001
DVI 10000-001
2
MAR15
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
LOWER SURFACE.
3. OPEN ACCES DOOR 293BL (294BR).
003
____________________________________
REMOVAL
539300-RAI-10000
*** CONTINUED ***
AH
28-21-71
DVI 10000-001
2-400 PAGE
2
MAR 01/15
28-21-71
DETAILED VISUAL
HARNESS
DVI 10000-001
3
MAR15
004
_______________________________________
DETAILED
VISUAL INSPECTION OF FUEL PUMP
REF. FIG. 282171-RAI-00120
CHECK THAT :
- ELECTRCAL HARNESS IS IN GOOD CONDITION AND
NOT FRAYED, ESPECIALLY AT CONNECTION.
- BONDING STRIPS ARE NOT CORRODED.
- BONDING STRIPS ARE CORRECTLY ATTACHED.
- HARNESS CLAMP IS CORRECTLY INSTALLED.
005
________
CLOSE-UP
CLOSE ACCESS DOOR 293BL (294BR).
006
_________________________________________
INSTALLATION
539300-RAI-10000

PREVIOUSLY REMOVED.
*****
AH
E N D
O F
T E X T
*****
28-21-71
DVI 10000-001
2-400 PAGE
3
MAR 01/15
28-21-71
4
AH
ELECTRIC PUMP ASSEMBLY
DVI 10000-001
MAR15
28-21-71
DVI 10000-001
2-400
PAGE
4
MAR 01/15
28-21-71

RAI 10000-001
1
MAR15
ZONING DATA
___________
ZONE
ACCESS
: 293
294
522
622
: 293BL 294BR
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE

01 R/I TOOL, FUEL PUMP
98S28002515000
SPARE
: 01 ELECTRIC PUMP
282170-10
EXPENDABLE
: 02 O-RINGS
282171-01-010
BULK MATERIAL : SEALANT
_________
MAN-HOURS
09-018
PUBLICATION
___________
JIC

SYSTEM
AH
28-21-00-OPT-10000
28-21-71
RAI 10000-001
2-400 PAGE
1
MAR 01/15
28-21-71

001
RAI 10000-001
2
MAR15
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
LOWER SURFACE.
3. OPEN ACCES DOOR 293BL (294BR).
003
______________________________
DE-ENERGIZATION
OF FUEL SYSTEM
1. ON PANEL 121VU,
A. OPEN THE FOLLOWING CIRCUIT BREAKERS :
*** CONTINUED ***
AH
28-21-71
RAI 10000-001
2-400 PAGE
2
MAR 01/15
28-21-71

RAI 10000-001
3
MAR15
1QA (2QA) FUEL/FUEL FEED/ENG1 (2)/

ELEC/PUMP.
CTL &/CAUTION.
B. INSTALL SAFETY CLIPS.
004
________________________
REMOVAL
OF ELECTRIC PUMP
REF. FIG. 282171-RAI-00120
1. DISCONNECT ELECTRICAL CONNECTOR (2) REMOVE
FASTENER (4) FROM RETAINING CLAMP (3).
2. INSTALL CONTAINER TO RECOVER FUEL (FUEL CONTAINED IN PUMP CANISTER).
3. REMOVE ELECTRIC PUMP RETAINING SCREWS (5)
R
R
R
R
R
R
R
R
4. REMOVAL OF ELECTRIC PUMP (1):

A. POSITION TOOL ON ELECTRIC PUMP AND
SCREW BOTH TOOL STUDS IN PUMP HOLES.
B. PULL DOWN ELECTRIC PUMP BY MEANS OF
TOOL.
C. TURN RIGHT ELECTRIC PUMP IN ORDER
TO PULL AGAIN AND REMOVE IT FROM
ITS HOUSING.
5. REMOVE AND DISCARD PUMP TWO SEALS (6).
EQUIPMENT.
005
_____________________________
INSTALLATION
OF ELECTRIC PUMP
REF. FIG. 282171-RAI-00120
PREPARATION OF REPLACEMENT COMPONENT (IF REQUIRED).
*** CONTINUED ***
AH
28-21-71
RAI 10000-001
2-400 PAGE
3
MAR 01/15
28-21-71

RAI 10000-001
4
MAR15
1. INSTALL TWO NEW SEALS (6).

(SEALS MUST BE PREVIOUSLY LUBRICATED WITH
CLEAN FUEL).
2. PLACE IMMERSED PART OF ELECTRIC PUMP IN
CLEAN FUEL.
AREA.
4. LOCK ELECTRIC PUMP (1) USING PIN TOOL(TURN
LEFT).
5. INSTALL SCREW (5) AND TIGHTEN.
6. INSTALL ELECTRIC CONNECTOR (2) ON ITS SUPPORT, ATTACH CLAMP (3) WITH FASTENER (4).
8. IF NECESSARY, SEAL THE CHANFER BEETWEN PUMP
AND CANISTER FLANGES WITH OF THE SEALANT.
SMOOTH.
006
___________________________
ENERGIZATION
OF FUEL SYSTEM
1. ON PANEL 121VU
A. REMOVE SAFETY CLIPS
B. CLOSE THE FOLLOWING CIRCUIT BREAKERS :
- 1QA (2QA) AND 3QA (4QA)
007
________
CLOSE-UP
CLOSE ACCESS DOOR 293BL (294BR).
008
________
CLOSE-UP
*** CONTINUED ***
AH
28-21-71
RAI 10000-001
2-400 PAGE
4
MAR 01/15
28-21-71

RAI 10000-001
5
MAR15

6. REMOVE PLATFORM.
009
R
_______________________________
OPERATIONAL
TEST OF FUEL SYSTEM
282100-OPT-10000
*****
AH
E N D
O F
T E X T
*****
28-21-71
RAI 10000-001
2-400 PAGE
5
MAR 01/15
28-21-71
6
AH
RAI 10000-001
MAR15
28-21-71
RAI 10000-001
2-400
PAGE
6
MAR 01/15
28-21-72

CANISTER
RAI 10000-001
1
MAR15
ZONING DATA
___________
ZONE
ACCESS
: 293
522
622
: 293BL
522AB
622AB
294
294BR
522CT
622CT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE

01 TOP SKIN ACCESS PLATFORM
01 R/I TOOL, FUEL PUMP
98S28002515000
SPARE
: 01 ELECTRIC PUMP CANISTER

01 ELECTRIC PUMP
282170-10
282170-10
EXPENDABLE
: 03 SEAL
02 O-RINGS
282170-10
282171-01-010
BULK MATERIAL : DRY LUBRICANT MOLYKOTE 3402

PURE MINERAL VASELINE
SEALANT
_________
MAN-HOURS
06-001
04-012
09-018
PUBLICATION
___________
JIC
JIC

: REFUELING
AH
57-00-00-OAC-10000
12-11-00-FLG-10020
28-21-72
RAI 10000-001
2-400 PAGE
1
MAR 01/15

CANISTER
28-21-72
RAI 10000-001
2
MAR15
PUBLICATION
___________
JIC

SYSTEM
AH
28-21-00-OPT-10000
28-21-72
RAI 10000-001
2-400 PAGE
2
MAR 01/15
28-21-72

CANISTER
001
RAI 10000-001
3
MAR15
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
1. MAKE CERTAIN THAT TANKS ARE EMPTIES. IF NONE
MAKE A DEFUELLING AND A DRAINING.
(AMM: 121100-DFG-10000 / 122428-DRN-10010).
2. INSTALL A WARNING NOTICE IN FLIGHT COMPARTMENT PROHIBITING ENERGIZATION OF FUEL SYSTEM.
LOWER SURFACE.
4. OPEN ACCESS DOORS 293BL (294BR) LOCATED
ON KARMAN.
*** CONTINUED ***
AH
28-21-72
RAI 10000-001
2-400 PAGE
3
MAR 01/15
28-21-72

CANISTER
RAI 10000-001
4
MAR15

UPPER SURFACE.
6. REMOVE ACCESS DOORS 522AB (622AB) AND 522CT
(622CT) AS FOLLOWS :
003
_______________________________
OPENING
570000-OAC-10000
004
______________________________
DE-ENERGIZATION
OF FUEL SYSTEM
1. ON PANEL 121VU,
ELEC/PUMP.
CTL &/CAUTION.
005
________________________
REMOVAL
OF ELECTRIC PUMP
REF. FIG. 282171-RAI-00120
1. DISCONNECT ELECTRICAL CONNECTOR (2) REMOVE
FASTENER (4) FROM RETAINING CLAMP (3).
2. INSTALL CONTAINER TO RECOVER FUEL (FUEL CONTAINED IN PUMP CANISTER).
3. REMOVE ELECTRIC PUMP RETAINING SCREWS (5)
R
R
R
R
R
R
4. REMOVAL OF ELECTRIC PUMP (1):

A. POSITION TOOL ON ELECTRIC PUMP AND
SCREW BOTH TOOL STUDS IN PUMP HOLES.
B. PULL DOWN ELECTRIC PUMP BY MEANS OF
TOOL.
C. TURN RIGHT ELECTRIC PUMP IN ORDER
*** CONTINUED ***
AH
28-21-72
RAI 10000-001
2-400 PAGE
4
MAR 01/15
28-21-72

CANISTER
R
R
RAI 10000-001
5
MAR15
TO PULL AGAIN AND REMOVE IT FROM

ITS HOUSING.
5. REMOVE AND DISCARD PUMP TWO SEALS (6).
EQUIPMENT.
006
_________________________________
REMOVAL
OF ELECTRIC PUMP CANISTER
REF. FIG. 282172-RAI-00100
1. REMOVE FASTENERS (2) AND (8) OF CLAMPS (4)
AND (6). REMOVE BONDING STRIPS (3) AND (7).
2. UNSCREW NUTS (1) AND (9). REMOVE PIPE (5).
3. UNSCREW WITH PRECAUTION NUT (20) IN ORDER
TO REMOVE THE RING (17).
4. REMOVE AND DISCARD SEAL (18). REMOVE RING
(19) AND NUT (20).
5. REMOVE SCREWS (14). REMOVE PUMP CANISTER(12)
7. UNSCREW UNION (10); DISCARD SEAL (11).
007
______________________________________
INSTALLATION
OF ELECTRIC PUMP CANISTER
REF. FIG. 282172-RAI-00100
1. PREPARATION OF REPLACEMENT COMPONENT :
A. CHECK CONDITION OF FILTER SCREEN.
B. CHECK THAT VALVE (15) OPERATES CORRECTLY.
*** CONTINUED ***
AH
28-21-72
RAI 10000-001
2-400 PAGE
5
MAR 01/15
28-21-72

CANISTER
RAI 10000-001
6
MAR15
C. LUBRICATE SEALS (11), (13) AND (18) WITH

CLEAN FUEL.
D. INSTALL NEW SEAL (11). APPLY A FILM OF
DRY LUBRICANT ON THREADS AND SCREW UNION
(10).
E. INSTALL NUT (20) ON CANISTER (12).
F. INSTALL RING (19). INSTALL A NEW SEAL
(18) ON CANISTER.
G. INSTALL A NEW SEAL (13) ON CANISTER.
2. INSTALL CANISTER (12) ON ITS BOX. ATTACH
WITH SCREWS (14).
3. APPLY A FILM OF DRY LUBRICANT ON PIPE (16)
THREADS.
4. INSTALL RING (17). TIGHTEN NUT (20).
5. INSTALL PIPE (5). TIGHTEN NUTS (1) AND (9).
6. APPLY A THIN FILM OF PURE MINERAL VASELINE
ON MATING SURFACES OF BONDING STRIPS.
7. TIGHTEN FASTENERS (2) AND (7) OF BONDING
STRIPS (3) AND (7) ON CLAMPS (4) AND (6).
008
_____________________________
INSTALLATION
OF ELECTRIC PUMP
REF. FIG. 282171-RAI-00120
PREPARATION OF REPLACEMENT COMPONENT (IF REQUIRED).
1. INSTALL TWO NEW SEALS (6).
(SEALS MUST BE PREVIOUSLY LUBRICATED WITH
CLEAN FUEL).
*** CONTINUED ***
AH
28-21-72
RAI 10000-001
2-400 PAGE
6
MAR 01/15
28-21-72

CANISTER
RAI 10000-001
7
MAR15
2. PLACE IMMERSED PART OF ELECTRIC PUMP IN

CLEAN FUEL.
AREA.
4. LOCK ELECTRIC PUMP (1) USING PIN TOOL(TURN
LEFT).
5. INSTALL SCREW (5) AND TIGHTEN.
6. INSTALL ELECTRIC CONNECTOR (2) ON ITS SUPPORT, ATTACH CLAMP (3) WITH FASTENER (4).
8. IF NECESSARY, SEAL THE CHANFER BEETWEN PUMP
AND CANISTER FLANGES WITH OF THE SEALANT.
SMOOTH.
009
________
CLOSE-UP
INSTALL ACCESS DOORS 522AB (622AB), 522CT
010
________________________________
CLOSING
570000-OAC-10000
011
_________
REFUELING
121100-FLG-10020
012
___________________________
ENERGIZATION
OF FUEL SYSTEM
1. ON PANEL 121VU
*** CONTINUED ***
AH
28-21-72
RAI 10000-001
2-400 PAGE
7
MAR 01/15
28-21-72

CANISTER
RAI 10000-001
8
MAR15

013
_______________________________
OPERATIONAL
TEST OF FUEL SYSTEM
282100-OPT-10000
R
014
________
CLOSE-UP
6. REMOVE PLATFORM.
*****
AH
E N D
O F
T E X T
*****
28-21-72
RAI 10000-001
2-400 PAGE
8
MAR 01/15
28-21-72
9
AH
PUMP CANISTER
RAI 10000-001
MAR15
28-21-72
RAI 10000-001
2-400
PAGE
9
MAR 01/15
28-21-72
10
AH
RAI 10000-001
MAR15
28-21-72
RAI 10000-001
2-400
PAGE
10
MAR 01/15
28-21-73

OF THERMAL RELIEF VALVE
RAI 10000-001
1
MAR15
ZONING DATA
___________
ZONE
ACCESS
: 522
622
: 522CT
622CT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
MECHANIC
___
MEN
_________
MAN-HOURS
01
ELAPSED TIME
GSE
SPARE
: 01 THERMAL EXPANSION VALVE
282170-10-250
EXPENDABLE
: 01 O-RING
282170-10-270

SYSTEM
57-00-00-OAC-10000
PUBLICATION
___________
JIC
JIC
AH
28-21-00-OPT-10000
28-21-73
RAI 10000-001
2-400 PAGE
1
MAR 01/15
28-21-73

001
RAI 10000-001
2
MAR15
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
1. CHECK THAT FUEL TANKS ARE DEFUELED OR THAT
FUEL LEVEL IS BELOW FUEL LINE LEVEL.
3. INSTALL PLATFORM, 3.76 M (12.34 FT), TO GAIN
ACCESS TO WING UPPER SURFACE.
4. REMOVE ACCESS DOOR 522CT (622CT) AS FOLLOWS.
*** CONTINUED ***

AH
28-21-73
RAI 10000-001
2-400 PAGE
2
MAR 01/15
28-21-73

003
RAI 10000-001
3
MAR15
________________________________
OPENING
570000-OAC-10000
NOTA: OPENING THE ACCESS DOOR 522CT (622CT).
004
__________________________________
REMOVAL
OF THERMAL EXPANSION VALVE
REF. FIG. 282173-RAI-00110
1. REMOVE THERMAL EXPANSION VALVE (1) LOCATED
ALONG ENGINE FEED JET PUMP AXIS.
2. DISCARD THE SEAL (2).
3. BLANK LINES.
005
_______________________________________
INSTALLATION
OF THERMAL EXPANSION VALVE
REF. FIG. 282173-RAI-00110
1. REMOVE BLANKS.
REQUIRED). IMMERSE REPLACEMENT COMPONENT IN
CLEAN FUEL.
AREA. MAKE CERTAIN THAT LINE END FITTINGS
ARE IN GOOD CONDITION.
4. INSTALL THE SEAL (2) ON THE VALVE (1).
5. INSTALL THERMAL EXPANSION VALVE (1) ON ITS
LINE AND TIGHTEN.
*** CONTINUED ***
AH
28-21-73
RAI 10000-001
2-400 PAGE
3
MAR 01/15
28-21-73

006
RAI 10000-001
4
MAR15
________
CLOSE-UP
INSTALL ACCESS DOOR 522CT (622CT) AS FOLLOWS :
007
________________________________
CLOSING
570000-OAC-10000
CLOSE THE ACCESS DOORS PREVIOUSLY OPENED.
008
________
CLOSE-UP
6. REMOVE PLATFORM.
009
R
_______________________________
OPERATIONAL
TEST OF FUEL SYSTEM
282100-OPT-10000
*****
AH
E N D
O F
T E X T
*****
28-21-73
RAI 10000-001
2-400 PAGE
4
MAR 01/15
28-21-73
5
AH
THERMAL EXPANSION
VALVE
RAI 10000-001
MAR15
28-21-73
RAI 10000-001
2-400
PAGE
5
MAR 01/15
28-21-74

OF VAPOR RELIEF VALVE
RAI 10000-001
1
MAR15
ZONING DATA
___________
ZONE
ACCESS
: 522
622
: 522CT
622CT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
MECHANIC
___
MEN
_________
MAN-HOURS
01
ELAPSED TIME
GSE
SPARE
: 02 VAPOR RELIEF VALVE
282170-10-240
EXPENDABLE
: 02 O-RING
282170-10-080

SYSTEM
57-00-00-OAC-10000
PUBLICATION
___________
JIC
JIC
AH
28-21-00-OPT-10000
28-21-74
RAI 10000-001
2-400 PAGE
1
MAR 01/15
28-21-74

001
RAI 10000-001
2
MAR15
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
*** CONTINUED ***

AH
28-21-74
RAI 10000-001
2-400 PAGE
2
MAR 01/15
28-21-74

003
RAI 10000-001
3
MAR15
_______________________________
OPENING
570000-OAC-10000
004
_____________________________
REMOVAL
1. REMOVE VAPOR RELIEF VALVE (1) LOCATED ALONG
ELECTRIC PUMP AXIS.
DISCARD SEAL (2).
2. BLANK LINES.
005
__________________________________
INSTALLATION
REF. FIG. 282174-RAI-00100
1. REMOVE BLANKS.
REQUIRED). IMMERSE REPLACEMENT COMPONENT
IN CLEAN FUEL.
AREA. MAKE CERTAIN THAT LINE END FITTINGS
ARE IN GOOD CONDITION.
4. INSTALL VAPOR RELIEF VALVE (1) AND ITS SEAL
(2) ON ITS LINE AND TIGHTEN.
006
________
CLOSE-UP
007
________________________________
CLOSING
570000-OAC-10000
*** CONTINUED ***
AH
28-21-74
RAI 10000-001
2-400 PAGE
3
MAR 01/15
28-21-74

008
RAI 10000-001
4
MAR15
________
CLOSE-UP
6. REMOVE PLATFORM.
009
R
_______________________________
OPERATIONAL
TEST OF FUEL SYSTEM
282100-OPT-10000
*****
AH
E N D
O F
T E X T
*****
28-21-74
RAI 10000-001
2-400 PAGE
4
MAR 01/15
28-21-74
5
AH
VAPOR RELIEF VALVE
RAI 10000-001
MAR15
28-21-74
RAI 10000-001
2-400
PAGE
5
MAR 01/15
28-21-75

OF ENGINE FUEL ELEC PUMP
AUTO CTL PRESSURE SWITCH
RAI 10000-001
1
APR05
ZONING DATA
___________
ZONE
: 511
611
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
_________
MAN-HOURS
ELAPSED TIME
SPARE
: 01 O-RING
282170-09
: ENGINE GROUND IDLE RUNUP WITH GROUND POWER

UNIT
72-00-00-ERU-10030
PUBLICATION
___________
JIC
AH
28-21-75
RAI 10000-001
2-400 PAGE
1
APR 01/05
28-21-75

001
RAI 10000-001
2
APR05
___________
PREPARATION
REF. FIG. 282175-RAI-00100
1. IF THE BUILT-IN TANK CORRESPONDING TO THE
PRESSURE-SWITCH IS FULL, DEFUEL TO LOWLEVEL. (SEE JIC 121100-DEG-10000)
2. ON PANEL 121VU,
OPEN THE CIRCUIT-BREAKER :
3QA (4QA) FUEL/FUEL FEED/ENG1 (ENG2)/CTL
& CAUTION
3. OPEN THE INNER LEADING EDGE 511 (611) AFTER
UNSCREWED THE SCREWS ON THE TOP SKIN.
002
REMOVAL OF ENG FUEL ELEC PUMP,AUTO CTL

______________________________________
PRESSURE-SWITCH
_______________
REF. FIG. 282175-RAI-00100
1. DISCONNECT THE PRESSURE-SWITCH CONNECTOR (2)
-17QA (18QA).
2. UNTIGHT WITH HAND AND REMOVE THE PRESSURESWITCH.
3. REJECT THE O-RING (3).
003
INSTALLATION OF ENG FUEL ELEC PUMP

__________________________________
AUTO CTL PRESSURE-SWITCH
________________________
REF. FIG. 282175-RAI-00100
1. PLACE A NEW O-RING (3).
NOTE : DO NOT USE TOOL TO SCREW THE PRESSURESWITCH (1) (RISK TO UNCRIMP THE BASE).
2. SCREW THE PRESSURE-SWITCH (2) AND TIGHTEN
*** CONTINUED ***
AH
28-21-75
RAI 10000-001
2-400 PAGE
2
APR 01/05
28-21-75

RAI 10000-001
3
APR05
STRONGLY WITH HAND.

3. CONNECT THE CONNECTOR (1) ON THE PRESSURESWITCH.
4. CLEAN WELL THE AREA TO CAN CHECK LATER ALL
LEAKAGE.
5. CLOSE THE INNER LEADING EDGE -511 (611).
004
ENGINE GROUND IDLE RUN-UP WITH

______________________________
GROUND POWER UNIT
_________________
720000-ERU-10030
005
VISUEL INSPECTION FOR LEAKAGE DETECTION

_______________________________________
IN THE PLANE OF PRESSURE-SWITCH
_______________________________
REF. FIG. 282175-RAI-00100
1. OPEN THE INNER LEADING EDGE -511 (611).
2. MAKE CERTAIN MINUTELY THAT ANY FUEL LEAKAGE APPEARS AROUND THE PRESSURE-SWITCH
(2).
3. CLOSE THE INNER LEADING EDGE -511 (611).
*****
AH
E N D
O F
T E X T
*****
28-21-75
RAI 10000-001
2-400 PAGE
3
APR 01/05
28-21-75
4
AH
ENG FUEL ELEC PUMP

RAI 10000-001
APR05
28-21-75
RAI 10000-001
2-400
PAGE
4
APR 01/05
28-21-77

OF ENGINE FEED JET PUMP
RAI 10000-001
1
MAR15
ZONING DATA
___________
ZONE
ACCESS
: 522
622
: 522CT
622CT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
SPARE
: 01 ENGINE FEED JET PUMP
282170-09
EXPENDABLE
: 03 SEAL
04 SCREW
282170-09
282100-09
BULK MATERIAL : PETROLATUM

DRY LUBRICANT
_________
MAN-HOURS
04-012
06-001
PUBLICATION
___________
JIC
JIC
JIC

SYSTEM
AH
57-00-00-OAC-10000
28-21-00-OPT-10000
57-00-00-OAC-10000
28-21-77
RAI 10000-001
2-400 PAGE
1
MAR 01/15
28-21-77

001
RAI 10000-001
2
MAR15
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
*** CONTINUED ***

AH
28-21-77
RAI 10000-001
2-400 PAGE
2
MAR 01/15
28-21-77

003
RAI 10000-001
3
MAR15
_______________________________
OPENING
570000-OAC-10000
004
_______________________________
REMOVAL
REF. FIG. 282177-RAI-00110
1. UNSCREW NUTS (4), (8) AND (10). DISCONNECT
LINES (3) AND (9).
2. UNSCREW NUT (2). LOOSEN NUT (18) AND ROTATE
LINE (1) IN ORDER TO DISCONNECT IT FROM
COUPLING (5).
3. REMOVE SCREW (15), WASHER (16) IN ORDER TO
DISCONNECT BONDING STRIP (17) FROM FEED JET
PUMP.
4. REMOVE THE THREE SCREWS (21), THE THREE
WASHERS (22) OF TRIANGULAR BASE OF LINE
(19).
5. UNSCREW NUT (27) FROM LINE (23).
6. REMOVE TWO SCREWS (13), TWO SCREWS (28).
RECOVER THEIRS WASHERS AND MOVE FEED JET
PUMP (14) BACK IN ORDER TO DISCONNECT LINE
(23). REMOVE THE TWO HALF-SHELLS (24).
DISCARD SEAL (20).
7. REMOVE FEED JET PUMP (14).
8. REMOVE CLIP (26) AND NUT (27). DISCARD SEAL
(25).
9. LOOSEN JAM NUT (6), UNSCREW THEN REMOVE COUPLING (5). DISCARD SEAL (7).
10.REMOVE COUPLING (11). DISCARD SEAL (12).
*** CONTINUED ***
AH
28-21-77
RAI 10000-001
2-400 PAGE
3
MAR 01/15
28-21-77

RAI 10000-001
4
MAR15
11.BLANK ORIFICES OF REMOVED EQUIPMENT.

12.PROTECT REMOVED COMPONENT INTERFACE AS WELL
AS ADJACENT AREA.
005
____________________________________
INSTALLATION
REF. FIG. 282177-RAI-00110
NOTE : CHECK THAT FILTER SCREEN IS CLEAN.
1. REMOVE BLANKING CAPS INSTALLED DURING
REMOVAL.
2. INSTALL NEW SEALS (7) AND (12) ON COUPLINGS
(5) AND (11). (SEALS MUST BE PREVIOUSLY LUBRICATED IN CLEAN FUEL).
3. INSTALL COUPLINGS (5) AND (11) ON FEED JET
PUMP (14). TIGHTEN JAM NUT (6).
4. INSTALL SCREW (27), CLIP (26), SEAL (25)
ON FEED JET PUMP. SEAL (25) MUST BE PREVIOUSLY LUBRICATED IN CLEAN FUEL.
5. COAT THREADS OF LINE (23) AND NUT (27) WITH
DRY LUBRICANT.
6. INSTALL THE TWO HALF-SHELLS (24) AND CONNECT
LINE (23) ON FEED JET PUMP.
7. INSTALL A NEW SEAL (20) ON COUPLING TRIANGULAR BASE (SEAL MUST BE PREVIOUSLY LUBRICATED IN CLEAN FUEL).
8. CLEAN BONDING PLATE OF FEED JET PUMP.
9. POSITION THE ASSEMBLY ON ITS LOCATION TAKING
CARE NOT TO DAMAGE FILTER SCREEN.
10.INSTALL SCREWS AND WASHERS (21), (22) AND
*** CONTINUED ***
AH
28-21-77
RAI 10000-001
2-400 PAGE
4
MAR 01/15
28-21-77

RAI 10000-001
5
MAR15
TIGHTEN.
11.INSTALL THE TWO SCREWS (13) AND TWO SCREWS
(28) WITH THEIRS WASHERS, TIGHTEN.
12.APPLY A THIN FILM OF PURE MINERAL VASELINE
ON BONDING AREAS AND CONNECT BONDING STRIP
(17) BY MEANS OF SCREW (15) AND WASHER (16)
ON FEED JET PUMP (14).
13. INSTALL LINES (3) AND (9). TIGHTEN NUTS (4)
(8) AND (10).
14.ROTATE LINE (1). CONNECT IT TO COUPLING (5).
TIGHTEN NUTS (2) AND (18).
006
_______________________________
OPERATIONAL
TEST OF FUEL SYSTEM
282100-OPT-10000
R
007
________
CLOSE-UP
008
________________________________
CLOSING
570000-OAC-10000
009
________
CLOSE-UP
*** CONTINUED ***
AH
28-21-77
RAI 10000-001
2-400 PAGE
5
MAR 01/15
28-21-77

RAI 10000-001
6
MAR15
6. REMOVE PLATFORM.
*****
AH
E N D
O F
T E X T
*****
28-21-77
RAI 10000-001
2-400 PAGE
6
MAR 01/15
28-21-77
7
AH
ENGINE FEED JET PUMP
RAI 10000-001
MAR15
28-21-77
RAI 10000-001
2-400
PAGE
7
MAR 01/15
28-21-78
FUNCTIONAL TEST OF
FUT 10000-001
1
DEC14
ZONING DATA
___________
ZONE
: 211
522
622
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE

01 FEED JET PUMP TOOL
_________
MAN-HOURS
98S28003001000
PUBLICATION
___________
JIC
SUPPLY
AH
24-46-00-EAD-10000
28-21-78
FUT 10000-001
2-400 PAGE
1
DEC 01/14
28-21-78
FUNCTIONAL TEST OF
001
FUT 10000-001
2
DEC14
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
003
___________
PREPARATION
1. ON PANEL 4 VU
TANK CONTAINS BETWEEN 300 AND 700KG (661 AND
1542LBS).
NOTE: IF REQUIRED, TOP UP TANKS.
*** CONTINUED ***
AH
28-21-78
FUT 10000-001
2-400 PAGE
2
DEC 01/14
28-21-78
FUNCTIONAL TEST OF
FUT 10000-001
3
DEC14
UNDER SURFACE.
004
_______________________________________
FUNCTIONAL
TEST OF FEEDER TANK JET PUMP
REF. FIG. 282178-FUT-00110
REF. FIG. 282100-OPT-00120
NOTE: PLACE MEASURING TOOL ON WATER DRAIN OF
FEEDER TANK. (THIS DRAIN IS LOCATED NEAR
OF WING FAIRING. BETWEEN RIB4 AND RIB5).
SEE INSTALLATION ON THE ILLUSTRATION.
1. ON FUEL SECTION OF PANEL 25VU.
A. PRESS ENG PUMP PUSHBUTTON SWITCH
- RUN LEGEND COMES ON
- OFF LEGEND GOES OFF
B. CHECK THAT FEED LO PR CAUTION LIGHT IS
OFF.
WARNING: STOP ELECTRIC PUMP IF THE PRESSURE
IS NOT INCREASES AFTER 10MN MAXIMUM.
2. CHECK ON PRESSURE GAGE THAT PRESSURE READ
INCREASES.
- FEEDER TANK JET PUMP OPERATES CORRECTLY.
3. ON FUEL SECTION OF PANEL 25VU, RELEASE
ENG PUMP PUSHBUTTON SWITCH
- RUN LEGEND GOES OFF
- OFF LEGEND COMES ON.
4. UNSCREW THE KNURLED KNOB (5), UNLOCK THE
KNURLED NUT (2), ROTATE THE UNIT (6) AND
REMOVE THE TOOL.
005

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
*** CONTINUED ***
AH
28-21-78
FUT 10000-001
2-400 PAGE
3
DEC 01/14
28-21-78
FUNCTIONAL TEST OF
006
FUT 10000-001
4
DEC14
________
CLOSE-UP
1. REMOVE PLATFORM.
2. CLEAN AROUND AIRCRAFT.
EQUIPMENT.
*****
AH
E N D
O F
T E X T
*****
28-21-78
FUT 10000-001
2-400 PAGE
4
DEC 01/14
28-21-78
5
AH
FUT 10000-001
DEC14
28-21-78
FUT 10000-001
2-400
PAGE
5
DEC 01/14
28-21-78
6
AH
FUEL DISTRIBUTION
OPERATIONAL TEST
FUT 10000-001
DEC14
28-21-78
FUT 10000-001
2-400
PAGE
6
DEC 01/14
28-21-78
FUNCTIONAL TEST OF
FUT 10000-002
1
DEC14
ZONING DATA
___________
ZONE
: 211
522
622
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE

01 FEED JET PUMP TOOL
_________
MAN-HOURS
98S28003001000
PUBLICATION
___________
JIC
JIC

(DISPLAY UNITS
EXPLORATION)
SUPPLY
AH
31-63-00-PRO-10000
24-46-00-EAD-10000
28-21-78
FUT 10000-002
2-400 PAGE
1
DEC 01/14
28-21-78
FUNCTIONAL TEST OF
001
FUT 10000-002
2
DEC14

___________________________________
EXPLORATION)
____________
_______________________
316300-PRO-10000
DISPLAY UNITS (DU).
002
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
*** CONTINUED ***

AH
28-21-78
FUT 10000-002
2-400 PAGE
2
DEC 01/14
28-21-78
FUNCTIONAL TEST OF
003
FUT 10000-002
3
DEC14

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
004
___________
PREPARATION
CHECK THAT EACH TANK CONTAINS BETWEEN 300
AND 700KG (661 AND 1542LBS).
NOTE: IF REQUIRED, TOP UP TANKS.
UNDER SURFACE.
005
_______________________________________
FUNCTIONAL
TEST OF FEEDER TANK JET PUMP
REF. FIG. 282178-FUT-00110
REF. FIG. 282100-OPT-00120
NOTE: PLACE MEASURING TOOL ON WATER DRAIN OF
FEEDER TANK. (THIS DRAIN IS LOCATED NEAR
OF WING FAIRING. BETWEEN RIB4 AND RIB5).
SEE INSTALLATION ON THE ILLUSTRATION.
1. ON FUEL SECTION OF PANEL 25VU.
A. PRESS ENG PUMP PUSHBUTTON SWITCH
- RUN LEGEND COMES ON
B. CHECK THAT FEED LO PR CAUTION LIGHT IS
OFF.
- PUMP LEGENDS ARE ON
- FEED LO PR MESSAGE IS NOT DISPLAYED
WARNING: STOP ELECTRIC PUMP IF THE PRESSURE
IS NOT INCREASES AFTER 10MN MAXIMUM.
*** CONTINUED ***
AH
28-21-78
FUT 10000-002
2-400 PAGE
3
DEC 01/14
28-21-78
FUNCTIONAL TEST OF
FUT 10000-002
4
DEC14
2. CHECK ON PRESSURE GAGE THAT PRESSURE READ

INCREASES.
- FEEDER TANK JET PUMP OPERATES CORRECTLY.
3. ON FUEL SECTION OF PANEL 25VU, RELEASE
ENG PUMP PUSHBUTTON SWITCH
- RUN LEGEND GOES OFF
- PUMP LEGENDS ARE OFF
4. UNSCREW THE KNURLED KNOB (5), UNLOCK THE
KNURLED NUT (2), ROTATE THE UNIT (6) AND
REMOVE THE TOOL.
006

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
007
________
CLOSE-UP
1. REMOVE PLATFORM.
2. CLEAN AROUND AIRCRAFT.
EQUIPMENT.
*****
AH
E N D
O F
T E X T
*****
28-21-78
FUT 10000-002
2-400 PAGE
4
DEC 01/14
28-21-78
5
AH
FUT 10000-002
DEC14
28-21-78
FUT 10000-002
2-400
PAGE
5
DEC 01/14
28-21-78
6
AH
FUEL DISTRIBUTION
OPERATIONAL TEST
FUT 10000-002
DEC14
28-21-78
FUT 10000-002
2-400
PAGE
6
DEC 01/14
28-21-78

OF FEEDER TANK JET PUMP
RAI 10010-001
1
MAR15
ZONING DATA
___________
ZONE
ACCESS
: 522
622
: 522AZ 522CT
622AZ 622CT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
SPARE
: 01 JET PUMP
282170-10
EXPENDABLE
: 03 SEAL
04 BOLT
04 WASHER
282170-10
282170-10
282170-10
BULK MATERIAL : DRY LUBRICANT - MOLYKOTE 3402

BUTADIENNE ADHESIVE
PURE MINERAL VASELINE
_________
MAN-HOURS
06-001
08-045
04-012
PUBLICATION
___________
JIC
JIC

SYSTEM
AH
57-00-00-OAC-10000
28-21-00-OPT-10000
28-21-78
RAI 10010-001
2-400 PAGE
1
MAR 01/15
28-21-78

001
RAI 10010-001
2
MAR15
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
1. MAKE CERTAIN THAT FUEL TANKS ARE DEFUELED.
3. INSTALL PLATFORM 4 M (13 FT), TO GAIN ACCESS
TO WING UPPER SURFACE.
4. REMOVE ACCESS DOORS 522AZ (622AZ) AND 522CT
*** CONTINUED ***

AH
28-21-78
RAI 10010-001
2-400 PAGE
2
MAR 01/15
28-21-78

003
RAI 10010-001
3
MAR15
________________________________
OPENING
570000-OAC-10000
NOTE: OPEN THE ACCESS DOORS INDICATED IN THE
ACCESS SECTION ON PAGE 1 OF THIS
JOB INSTRUCTION CARD.
004
_______________________________
REMOVAL
REF. FIG. 282178-RAI-00120
1. RELEASE NUT (5) AT LEVEL OF ELECTRIC PUMP
CANISTER.
2. RELEASE NUT (7), DISCONNECT LINE (6).
3. REMOVE COUPLING (8), DISCARD SEAL (9).
4. RELEASE NUTS (2) AND (14),DISCONNECT LINE
(15)
5. REMOVE COUPLING (13),DISCARD SEAL (12).
6. REMOVE FASTENERS (16).
7. REMOVE FASTENER (4) FROM BONDING STRIP ON
JET PUMP.
8. SIDE TANK, ON NOZZLE ASSY (21), UNSCREW
THREE NUTS (20) AND ONE NUT (18). REMOVE
SCREWS (17) AND (19) WITH THEIRS WASHERS.
9. DISENGAGE LINE (1) FROM JET PUMP (11),
REMOVE JET PUMP.
10 DISCARD SEAL (10).
11.BLANK OFF HOLES OF JET PUMP (11),LINE (1),
ELECTRIC PUMP CANISTER AND TEE COUPLING ON
JET PUMP.
*** CONTINUED ***
AH
28-21-78
RAI 10010-001
2-400 PAGE
3
MAR 01/15
28-21-78

RAI 10010-001
4
MAR15
12.PROTECT REMOVED COMPONENT INTERFACE AS WELL

AS ADJACENT AREA.
005
____________________________________
INSTALLATION
REF. FIG. 282178-RAI-00120
1. INSTALL NEW SEAL (10) ON JET PUMP, SEAL MUST
BE PREVIOUSLY IMMERSED IN CLEAN FUEL.
2. INSTALL THE TWO NEW SEALS (9) AND (12)
TIGHTEN BOTH COUPLINGS (8) AND (13) ON JET
PUMP.
3. CLEAN BONDING PLATE OF JET PUMP, AND BONDING
STRIP TERMINAL LUG.
4. APPLY A THIN FILM OF PURE MINERAL VASELINE
ON BONDING AREAS.
5. IMMERSE JET PUMP (11) IN CLEAN FUEL.
REMOVAL.
7. INSTALL JET PUMP (11) IN LINE (1).
8. POSITION THE ASSEMBLY ON ITS LOCATION AT RIB
5. INSTALL THREE SCREWS (19) AND ONE SCREW
(17) WITH THEIRS WASHERS. SIDE NOZZLE ASSY
(21) SCREW NUTS (18) AND (20). TIGHTEN.
9. CONNECT LINE (1) BONDING STRIP ON JET PUMP
(11) BY MEANS OF FASTENER (4).
10.TIGHTEN FASTENERS (16) OF LINE (1).
11.INSTALL LINES (6) AND (15), TIGHTEN UNIONS
(2), (5), (7) AND (14).
*** CONTINUED ***

AH
28-21-78
RAI 10010-001
2-400 PAGE
4
MAR 01/15
28-21-78

006
RAI 10010-001
5
MAR15
________________________________
CLOSING
570000-OAC-10000
NOTE: CLOSE THE ACCESS DOORS OPENED ABOVE.
007
________
CLOSE-UP
6. REMOVE PLATFORM.
008
R
_______________________________
OPERATIONAL
TEST OF FUEL SYSTEM
282100-OPT-10000
*****
AH
E N D
O F
T E X T
*****
28-21-78
RAI 10010-001
2-400 PAGE
5
MAR 01/15
28-21-78
6
AH
RAI 10010-001
MAR15
28-21-78
RAI 10010-001
2-400
PAGE
6
MAR 01/15
28-21-78

NOZZLE ASSY
RAI 10030-001
1
MAR15
ZONING DATA
___________
ZONE
ACCESS
: 522
622
: 522AZ 522CT
622AZ 622CT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
SPARE
: 02 SHIM (LEFT, RIGHT)

01 JET PUMP NOZZLE (LEFT)
01 JET PUMP NOZZLE (RIGHT)
282178
282170-16
282170-18
EXPENDABLE
: 01
05
01
05
01
00
282170-16
282170-16
282170-18
282170-18
282170
282170
SCREW (NOZZLE LEFT SIDE)

NUT (NOZZLE LEFT SIDE)
SCREW (NOZZLE RIGHT SIDE)
NUT (NOZZLE RIGHT SIDE)
NUT (LEFT, RIGHT SIDE)
WASHERS
BULK MATERIAL : DRY LUBRICANT - MOLYKOTE 3402
_________
MAN-HOURS
06-001
PUBLICATION
___________
JIC
JIC

SYSTEM
AH
57-00-00-OAC-10000
28-21-00-OPT-10000
28-21-78
RAI 10030-001
2-400 PAGE
1
MAR 01/15
28-21-78

NOZZLE ASSY
001
RAI 10030-001
2
MAR15
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
1. MAKE CERTAIN THAT FUEL TANKS ARE DEFUELED.
3. INSTALL PLATFORM 4 M (13 FT), TO GAIN ACCESS
TO WING UPPER SURFACE.
4. REMOVE ACCESS DOORS 522AZ (622AZ) AND 522CT
*** CONTINUED ***

AH
28-21-78
RAI 10030-001
2-400 PAGE
2
MAR 01/15
28-21-78

NOZZLE ASSY
003
RAI 10030-001
3
MAR15
________________________________
OPENING
570000-OAC-10000
NOTE: OPEN THE ACCESS DOORS INDICATED IN THE
004
REMOVAL OF FEEDER TANK

______________________
JET PUMP NOZZLE ASSY
____________________
REF. FIG. 282178-RAI-00140
1. UNSCREW NUT (2) AND REMOVE SCREW (3).
LIKE THAT WASHERS (4) AND (5) WHICH MAINTAIN
NOZZLE ASSY (1).
IDENTIFY POSITION OF WASHER (5).
2. UNSCREW SELF-LOCKING NUTS (7) AND (8) OF
RECOVER SCREWS AND WASHERS OF SIDE FEEDER
TANK JET PUMP.
REMOVE NOZZLE ASSY.
DON}T REMOVE THE SHIM (6).
005
INSTALLATION OF FEEDER TANK

___________________________
JET PUMP NOZZLE ASSY
____________________
REF. FIG. 282178-RAI-00140
1. CLEAN BONDING RANGES AND APPLY A FILM OF
CONTACT GREASE.
2. IF SHIM (6) IS NOT INSTALLED, INSTALL EITHER
A NEW SHIM OR ONE OF THE REMOVED NOZZLE
ASSY (1).
*** CONTINUED ***
AH
28-21-78
RAI 10030-001
2-400 PAGE
3
MAR 01/15
28-21-78

NOZZLE ASSY
RAI 10030-001
4
MAR15
TAKE CARE TO CORRECTLY INSTALL SHIM.

3. INSTALL NOZZLE ASSY (1) SCREW ONE NUT (7)
AND THREE NUTS (8) ON FOUR SCREWS OF FEEDER
TANK JET PUMP.
DO NOT TIGHTEN.
4. INSTALL SCREW (3) AND ONE WASHER (4).
INSTALL WASHER (5), ONE WASHER (4), MAINTAIN
TAB OF NOZZLE ASSY AND ONE WASHER (4).
SCREW THE NUT (2).
(JET PUMP FLANGE MUST BE AT: D= 8MM OF THE
BOTTOM OF LOWER SURFACE BOX).
5. TIGHTEN NUTS (2), (7) AND (8).
006
________________________________
CLOSING
570000-OAC-10000
NOTE: CLOSE THE ACCESS DOORS OPENED ABOVE.
007
________
CLOSE-UP
6. REMOVE PLATFORM.
*** CONTINUED ***
AH
28-21-78
RAI 10030-001
2-400 PAGE
4
MAR 01/15
28-21-78

NOZZLE ASSY
008
R
RAI 10030-001
5
MAR15
_______________________________
OPERATIONAL
TEST OF FUEL SYSTEM
282100-OPT-10000
*****
AH
E N D
O F
T E X T
*****
28-21-78
RAI 10030-001
2-400 PAGE
5
MAR 01/15
28-21-78
6
AH

NOZZLE ASSY
RAI 10030-001
MAR15
28-21-78
RAI 10030-001
2-400
PAGE
6
MAR 01/15
28-21-79

OF MOTIVE FLOW VALVE
RAI 10000-001
1
MAR15
ZONING DATA
___________
ZONE
ACCESS
: 475
485
512
612
: 475AT 485AT
512CT
612CT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
MECHANIC
_________
MAN-HOURS
01
ELAPSED TIME
GSE
SPARE
: 01 MOTIVE FLOW VALVE
282170-13-040
EXPENDABLE
: 02 O-RING
04 O-RING
04 NUT
282170
282160
282160
BULK MATERIAL : PETROLATUM

DRY LUBRICANT
04-012
06-004
PUBLICATION
___________
JIC
JIC
JIC
: DEFUELING
SYSTEM
AH
12-11-00-DFG-10000
54-00-00-RAI-10000
28-21-00-OPT-10000
28-21-79
RAI 10000-001
2-400 PAGE
1
MAR 01/15
28-21-79

001
RAI 10000-001
2
MAR15
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
______________________________
DE-ENERGIZATION
OF FUEL SYSTEM
1. ON PANEL 121VU,
ELEC/PUMP.
CTL &/CAUTION.
*** CONTINUED ***

AH
28-21-79
RAI 10000-001
2-400 PAGE
2
MAR 01/15
28-21-79

003
RAI 10000-001
3
MAR15
___________
PREPARATION
1. INSTALL WARNING NOTICE PROHIBITING ENERGIZATION OF FUEL SYSTEM.
2. INSTALL PLATFORM, 3.13 M (10.26 FT) TO GAIN
ACCESS TO WING LOWER SURFACE.
3. INSTALL PLATFORM, 3.76 M (12.34 FT) TO GAIN
4. DEFUELING TANKS AS FOLLOWS:
5. OPEN COWLS 475AT AND 485AT AS FOLLOWS :
004
_________
DEFUELING
121100-DFG-10000
005
____________________________________________
REMOVAL
540000-RAI-10000
006
____________________________
REMOVAL
REF. FIG. 282179-RAI-00110
1. REMOVE SCREWS AND WASHERS (2) AND (3).
2. REMOVE BONDING LEADS (1) FROM CLAMP (4).
3. UNSCREW UNION (20) AND MOVE BACK ONTO ATTACH
FITTING.
4. SLOWLY MOVE BACK SLEEVE (17) AND REMOVE THE
TWO HALF-JUMPERS (19).
5. CONTINUE TO CAREFULLY MOVE BACK SLEEVE (17)
AGAINST STOP AND REMOVE THE TWO HALF-JUMPERS
*** CONTINUED ***
AH
28-21-79
RAI 10000-001
2-400 PAGE
3
MAR 01/15
28-21-79

RAI 10000-001
4
MAR15
(16).
6. MOVE SPACER(18) BACK TOWARDS SLEEVE TO GAIN
ACCESS TO PIPE FASTENER (24).
7. POSITION CONTAINER UNDER PIPES AND UNSCREW
NUT (24) TO SEPARATE PIPE ASSY (25).
8. DISCONNECT CONNECTOR (10) AND BLANK CONNECTOR RECEPTACLES.
9. REMOVE THE THREE SCREWS (11) AND THE THREE
WASHERS (27).
REMOVE VALVE/PIPE ASSEMBLY,
REMOVE AND DISCARD SEALS (26) AND (12),
(15) AND (21).
10.REMOVE THE FOUR FASTENERS (6) AND (7),
SEPARATE THE MOTIVE FLOW VALVE (13) FROM
PIPE ASSEMBLY.
11.REMOVE AND DISCARD SELF-LOCKING NUTS.
12.REMOVE AND DISCARD SEALS (8) AND (9), RETAIN
SPACER (18).
13.BLANK OPEN PIPE ENDS AND TANK ORIFICE.
14.REMOVE MOTIVE FLOW VALVE (13).
007
_________________________________
INSTALLATION
REF. FIG. 282179-RAI-00110
1. REMOVE BLANDING PLUGS.
2. INSTALL TWO NEW SEALS (8) AND (9), COATED
WITH PURE PETROLATUM.
3. MAKE CERTAIN THAT PIPE AND VALVE ASSY BEA*** CONTINUED ***
AH
28-21-79
RAI 10000-001
2-400 PAGE
4
MAR 01/15
28-21-79

RAI 10000-001
5
MAR15
RING SURFACES ARE CLEAN. COAT THEM WITH A

THIN LAYER OF PURE PETROLATUM.
4. POSITION PIPE ASSY (5) ON MOTIVE FLOW VALVE
(13).
5. INSTALL SCREWS (6), INSTALL AND TIGHTEN NUTS
(7).
6. INSTALL TWO NEW SEALS (15) AND (21) ON
PIPES.
7. MAKE CERTAIN THAT VALVE AND FRONT SPAR
BEARING SURFACES ARE CLEAN AND CLEAN AND
COAT WITH A THIN OF PURE PETROLATUM.
8. INSTALL TWO NEW SEALS (12) AND (26),SEALS
PREVIOUSLY COATED WITH PURE PETROLATUM.
9. INSTALL SPACER (18).
10.POSITION CONSTITUTED ASSEMBLY AT DISLOCATION.
11.HOLD THE OTHER PIPE AND TORQUE NUT (24) TO
BETWEEN 1.8 TO 2 M.DAN.
12.MOVE SPACER (18) FORWARD.
13.POSITION AND HOLD THE TWO HALF-JUMPERS (16).
14.CAREFULLY MOVE SLEEVE (17) FORWARD UNTIL IT
HOLDS THE TWO HALF-JUMPERS (16).
15.ADJUST SPACER (18) AND CONTINUE TO MOVE
SLEEVE (17) FORWARD TO THE CENTER OF THE
SPACER.
16.POSITION AND HOLD THE TWO HALF-JUMPERS (19).
17.MOVE SLEEVE (18) FORWARD UP TO STOP.
*** CONTINUED ***
AH
28-21-79
RAI 10000-001
2-400 PAGE
5
MAR 01/15
28-21-79

RAI 10000-001
6
MAR15
18.APPLY DRY LUBRICANT TO SLEEVE THREADS.

19.MOVE UNION (20) FORWARD. TORQUE TO 0.5
M.DAN.
20.INSTALL THE THREE SCREWS (11) EQUIPPED WITH
WASHERS (27). TIGHTEN.
21.INSTALL THE BONDING LEADS (1) AFTER HAVING
CLEANED CONTACT SURFACES AND APPLIED A THEN
COAT OF PURE PETROLATUM.
22.INSTALL AND TIGHTEN SCREW (2) EQUIPPED WITH
WASHER (3).
23.REMOVE BLANKING CAPS FROM CONNECTOR RECEPTACLES AND CONNECT CONNECTOR (10) TO MOTIVE
FLOW VALVE (13).
008
___________________________
ENERGIZATION
OF FUEL SYSTEM
1. ON PANEL 121VU
009
_______________________________
OPERATIONAL
TEST OF FUEL SYSTEM
282100-OPT-10000
R
010
________
CLOSE-UP
CLOSE COWLS 475AT AND 485AT AS FOLLOWS :
*** CONTINUED ***

AH
28-21-79
RAI 10000-001
2-400 PAGE
6
MAR 01/15
28-21-79

011
RAI 10000-001
7
MAR15

_______________________________________
BY BOLTS
________
540000-RAI-10000
012
________
CLOSE-UP
6. REMOVE PLATFORM.
*****
AH
E N D
O F
T E X T
*****
28-21-79
RAI 10000-001
2-400 PAGE
7
MAR 01/15
28-21-79
8
AH
MOTIVE FLOW VALVE
RAI 10000-001
MAR15
28-21-79
RAI 10000-001
2-400
PAGE
8
MAR 01/15
28-23-00
OPS TEST OF FUEL CROSS

FEED VALVE INDICATION
COCKPIT/VISUAL INDICATOR
OPT 10000-002
1
DEC14
ZONING DATA
___________
ZONE
ACCESS
: 211
510
511
610
611
: 22AZ
521DT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
___
MEN
_________
MAN-HOURS
PUBLICATION
___________
JIC
JIC
SUPPLY
AH
24-46-00-EAD-10000
57-00-00-OAC-10000
28-23-00
OPT 10000-002
2-400 PAGE
1
DEC 01/14
28-23-00

001
OPT 10000-002
2
DEC14
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
003
_____________________________________
PREPARATION
OF CROSSFEED VALVE SYSTEM
1. ON PANEL 4VU
TANK CONTAINS 500 KG (1102 LBS).
NOTE : IF REQUIRED, TOP UP TANKS.
*** CONTINUED ***
AH
28-23-00
OPT 10000-002
2-400 PAGE
2
DEC 01/14

28-23-00
OPT 10000-002
3
DEC14

962VU.
- OPEN THE PANEL 214CZ TO HAVE ACCES TO
910VU.
004
OPERATIONAL TEST OF FUEL

________________________
CROSS FEED VALVE (PART 1)
_________________________
REF. FIG. 282100-OPT-00120
282000-OPT-00100
1. ENGINE 1
A. ON PANEL 25VU, FUEL/ENG1/PUMP PUSHBUTTON SWITCH RELEASED (OUT)
- RUN 1 LEGEND OFF
- OFF LEGEND ON.
B. PRESS FUEL/ENG1/PUMP PUSHBUTTON SWITCH
- RUN 1 LEGEND COMES ON
- FEED LO PR1 GOES OFF
- FEED LO PR2 IS ON.
C. PRESS FUEL/X FEED PUSHBUTTON SWITCH
- FLOWBAR IS IN LINE
- RUN 1 LEGEND ON, RUN 2 LEGEND REMAINS
OFF
- FEED LO PR1 LIGHT IS OFF
- FEED LO PR2 LIGHT GOES OFF
- ON PANEL 402VU, FUEL/X FEED LEGEND
IS ON.
D. RELEASE FUEL/X FEED PUSHBUTTON SWITCH
- FLOWBAR IS CROSSLINE
- RUN 1 LEGEND ON, RUN 2 LEGEND OFF
- FEED LO PR1 LIGHT OFF
- FEED LO PR2 LIGHT COMES ON
- ON PANEL 402VU, FUEL/X FEED LEGEND
GOES OFF.
*** CONTINUED ***
AH
28-23-00
OPT 10000-002
2-400 PAGE
3
DEC 01/14
28-23-00

OPT 10000-002
4
DEC14
E. RELEASE FUEL/ENG1/PUMP PUSHBUTTON

SWITCH (ELECTRIC PUMP SHUT DOWN)
- RUN 1 LEGEND GOES OFF
- OFF LEGEND COMES ON
- FEED LO PR1 AND FEED LO PR2 LIGHTS
ON.
005
_______________________________
OPENING
570000-OAC-10000
NOTE: OPEN THE ACCES DOORS INDICATED IN THE
006

________________________
CROSS FEED VALVE
________________
REF. FIG. 282100-OPT-00120
282000-OPT-00100
1. CHECK OF MECANICAL VISUAL INDICATOR.
A. ON PANEL 25VU, PRESS THE FUEL X/FEED
PUSHBUTTON SWITCH:
- UNDER ACCESS DOOR 521DT, CHECK THAT
MECANICAL VISUAL INDICATOR OF THE CROSS
FEED VALVE 3QE IS ON O POSITION(OPEN)
B. ON PANEL 25VU, RELEASE THE FUEL X/FEED
PUSHBUTTON SWITCH:
FEED VALVE 3QE IS ON F POSITION(SHUT)
007
_______________________________
CLOSING
570000-OAC-10000
*** CONTINUED ***
AH
28-23-00
OPT 10000-002
2-400 PAGE
4
DEC 01/14
28-23-00

OPT 10000-002
5
DEC14
NOTE: CLOSE THE ACCES DOORS OPENED ABOVE.

008

________________________
CROSS FEED VALVE
________________
REF. FIG. 282100-OPT-00120
282000-OPT-00100
1. CHECK OF PUMP ACTIVATION BY MEANS CROSS FEED
VALVE OPENNING.
A. ON PANEL 121VU, OPEN THE FOLLOWING
CIRCUIT BREAKERS:
1QA (2QA)
3QA (4QA)
B. ON THE PANEL 962VU (910VU),REMOVE RELAYS:
155 QA (154 QA)
C. ON THE PANEL 121VU, CLOSE THE CIRCUIT
BREAKERS.
D. ON PANEL 25VU:
(1) PRESS PUSHBUTTON SWITCH FUEL/ENG1/
PUMP (FUEL/ENG2/PUMP)
CHECK THAT LEGENDS:
. RUN AND OFF ARE OFF.
(2) PRESS PUSHBUTTON SWITCH FUEL/X FEED
CHECK THAT LEGENDS:
.RUN OF ENG1 PUMP (ENG2 PUMP)
COME ON (PUMP ACTIVATED).
(3) RELEASE PUSHBUTTON SWITCH FUEL/
X FEED
. RUN LEGENDS GOES OFF
2. A. ON THE PANEL 121VU, OPEN THE
FOLLOWING CIRCUIT BREAKERS:
1QA (2QA)
3QA (4QA)
B. ON 962VU (910VU), INSTALL RELAY:
*** CONTINUED ***
AH
28-23-00
OPT 10000-002
2-400 PAGE
5
DEC 01/14
28-23-00

OPT 10000-002
6
DEC14
155 QA (154 QA)

BREAKERS PREVIOUSLY OPENED.
009

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
010
_______________________
CLOSE-UP
OF FUEL SYSTEM
EQUIPMENT.
*****
AH
E N D
O F
T E X T
*****
28-23-00
OPT 10000-002
2-400 PAGE
6
DEC 01/14
28-23-00
7
AH
FUEL DISTRIBUTION
OPERATIONAL TEST
OPT 10000-002
DEC14
28-23-00
OPT 10000-002
2-400
PAGE
7
DEC 01/14
28-23-00
8
AH
OPT 10000-002
DEC14
28-23-00
OPT 10000-002
2-400
PAGE
8
DEC 01/14
28-23-00

OPT 10000-003
1
DEC14
ZONING DATA
___________
ZONE
ACCESS
: 211
510
511
610
611
: 22AZ
521DT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
___
MEN
_________
MAN-HOURS
PUBLICATION
___________
JIC
JIC
JIC

(DISPLAY UNITS
EXPLORATION)
SUPPLY
AH
31-63-00-PRO-10000
24-46-00-EAD-10000
57-00-00-OAC-10000
28-23-00
OPT 10000-003
2-400 PAGE
1
DEC 01/14
28-23-00

001
OPT 10000-003
2
DEC14

___________________________________
EXPLORATION)
____________
_______________________
316300-PRO-10000
DISPLAY UNITS (DU).
002
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
*** CONTINUED ***

AH
28-23-00
OPT 10000-003
2-400 PAGE
2
DEC 01/14
28-23-00

003
OPT 10000-003
3
DEC14

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
004
_____________________________________
PREPARATION
OF CROSSFEED VALVE SYSTEM
CHECK THAT EACH TANK CONTAINS 500 KG
(1102 LBS).
NOTE : IF REQUIRED, TOP UP TANKS.
962VU.
- OPEN THE PANEL 214CZ TO HAVE ACCES TO
910VU.
005

________________________
_________________________
REF. FIG. 282100-OPT-00120
REF. FIG. 282000-OPT-00100
REF. FIG. 282000-OPT-00130
1. ENGINE 1
A. - ON PANEL 25VU, FUEL/ENG1/PUMP
PUSHBUTTON SWITCH RELEASED (OUT)
. RUN 1 LEGEND OFF
. OFF LEGEND ON.
. ITEM 1 IS DISPLAYED.
. FEED LO PR MESSAGE IS DISPLAYED FOR
ENGINE 1.
PR MESSAGE IS DISPLAYED.
B. - ON PANEL 25 VU, PRESS FUEL/ENG1/PUMP
*** CONTINUED ***
AH
28-23-00
OPT 10000-003
2-400 PAGE
3
DEC 01/14

28-23-00
OPT 10000-003
4
DEC14
PUSHBUTTON SWITCH (ELECTRIC PUMP

OPERATING)
. RUN 1 LEGEND COMES ON
. OFF LEGEND GOES OFF
. FEED LO PR1 GOES OFF
. FEED LO PR2 IS ON.
. ITEM 2 IS DISPLAYED FOR ENGINE 1
. FEED LO PR MESSAGE OF ENGINE 1
DISAPPEARS
IS DISPLAYED.
C. - ON PANEL 25VU, PRESS FUEL/X FEED
PUSHBUTTON SWITCH
. FLOWBAR IS IN LINE
. RUN 1 LEGEND ON
. RUN 2 LEGEND REMAINS OFF
. FEED LO PR1 LIGHT IS OFF
. FEED LO PR2 LIGHT GOES OFF
. FUEL CROSSFEED VALVE FLOWBAR IS
IN LINE
. ITEM 1 REMAINS DISPLAYED FOR ENGINE 2
. FEED LO PR MESSAGE OF ENGINE 1 IS
NOT DISPLAYED
DISAPPEARS.
- ON MFD, IN TEMPORARY SELECTION WINDOW,
FUEL X FEED MESSAGE IS DISPLAYED.
D. - ON PANEL 25VU, RELEASE FUEL/X FEED
PUSHBUTTON SWITCH
. FLOWBAR IS CROSSLINE
. RUN 1 LEGEND ON, RUN 2 LEGEND OFF
. FEED LO PR1 LIGHT OFF
. FEED LO PR2 LIGHT COMES ON
*** CONTINUED ***
AH
28-23-00
OPT 10000-003
2-400 PAGE
4
DEC 01/14

28-23-00
OPT 10000-003
5
DEC14

CROSSLINE
. FEED LO PR MESSAGE OF ENGINE 1 IS
NOT DISPLAYED
APPEARS
ON MFD, IN TEMPORARY SELECTION WINDOW,
FUEL X FEED MESSAGE DISAPPEARS
ON EWD, IN ALERT WINDOW, FUEL FEED LO
PR MESSAGE APPEARS
MASTER CAUTION LIGHTS FLASH
SINGLE CHIME.
E. - ON PANEL 25VU, RELEASE FUEL/ENG1/PUMP

PUSHBUTTON SWITCH (ELECTRIC PUMP SHUT
DOWN)
. RUN 1 LEGEND GOES OFF
. OFF LEGEND COMES ON
. FEED LO PR1 AND FEED LO PR2
LIGHTS ON.
. FEED LO PR MESSAGE OF ENGINE 1(2)
ARE DISPLAYED.
PR MESSAGE REMAINS DISPLAYED.
006

________________________
_________________________
1. ENGINE 2
A. - ON PANEL 25VU, FUEL/ENG2/PUMP
PUSHBUTTON SWITCH RELEASED (OUT)
. RUN 2 LEGEND OFF
. OFF LEGEND ON.
. FEED LO PR MESSAGE APPEARS FOR
*** CONTINUED ***
AH
28-23-00
OPT 10000-003
2-400 PAGE
5
DEC 01/14

28-23-00
OPT 10000-003
6
DEC14
ENGINE 2
PR MESSAGE APPEARS
B. - ON PANEL 25VU, PRESS FUEL/ENG2/PUMP
OPERATING)
. RUN 2 LEGEND COMES ON
. OFF LEGEND GOES OFF
. FEED LO PR2 GOES OFF
. FEED LO PR1 IS ON.
- ON MFD UPPER WINDOW, IN ENGINE SD PAGE
DISAPPEARS
IS DISPLAYED
PR MESSAGE REMAINS DISPLAYED.
C. - ON PANEL 25VU, PRESS FUEL/X FEED
PUSHBUTTON SWITCH
. FLOWBAR IS IN LINE
. RUN 2 LEGEND ON
. RUN 1 LEGEND REMAINS OFF
. FEED LO PR1 LIGHT GOES OFF
IN LINE
IS NOT DISPLAYED
DISAPPEARS
FUEL X FEED MESSAGE IS DISPLAYED
*** CONTINUED ***
AH
28-23-00
OPT 10000-003
2-400 PAGE
6
DEC 01/14
28-23-00

OPT 10000-003
7
DEC14
D. - ON PANEL 25VU, RELEASE FUEL/X FEED

PUSHBUTTON SWITCH
. FLOWBAR IS CROSSLINE
. RUN 2 LEGEND IS ON
. RUN 1 LEGEND IS OFF
. FEED LO PR1 LIGHT COMES ON
. FUEL CROSSFEED VALVE FLOWBARD IS
CROSSLINE
IS NOT DISPLAYED
APPEARS
FUEL X FEED MESSAGE DISAPPEARS
PR MESSAGE APPEARS
- SINGLE CHIME
E. - ON PANEL 25VU, RELEASE FUEL/ENG2/PUMP
PUSHBUTTON SWITCH (ELECTRIC PUMP SHUT
DOWN)
. RUN 2 LEGEND GOES OFF
. OFF LEGEND COMES ON
. FEED LO PR1 AND FEED LO PR2
LIGHTS ON
. FEED LO PR MESSAGES OF ENGINE 1(2)
ARE DISPLAYED
PR MESSAGE REMAINS DISPLAYED
REMAINS EXTINGUISHED UNTIL THE FUEL
THRESHOLD.
*** CONTINUED ***
AH
28-23-00
OPT 10000-003
2-400 PAGE
7
DEC 01/14
28-23-00

OPT 10000-003
8
DEC14
THERE IS NO REQUIRMENT ON DELAY FOR

}FEED LOW PRESS} CAUTION LIGHT COMES
007
_______________________________
OPENING
570000-OAC-10000
008

________________________
CROSS FEED VALVE
________________
REF. FIG. 282100-OPT-00120
282000-OPT-00100
1. CHECK OF MECANICAL VISUAL INDICATOR.
A. ON PANEL 25VU, PRESS THE FUEL X/FEED
PUSHBUTTON SWITCH:
FEED VALVE 3QE IS ON O POSITION(OPEN)
B. ON PANEL 25VU, RELEASE THE FUEL X/FEED
PUSHBUTTON SWITCH:
FEED VALVE 3QE IS ON F POSITION(SHUT)
009
_______________________________
CLOSING
570000-OAC-10000
*** CONTINUED ***

AH
28-23-00
OPT 10000-003
2-400 PAGE
8
DEC 01/14
28-23-00

010
OPT 10000-003
9
DEC14

________________________
CROSS FEED VALVE
________________
REF. FIG. 282100-OPT-00120
REF. FIG. 282000-OPT-00100
1. CHECK OF PUMP ACTIVATION BY MEANS CROSS FEED
VALVE OPENNING.
A. ON PANEL 121VU, OPEN THE FOLLOWING
CIRCUIT BREAKERS:
1QA (2QA)
3QA (4QA)
B. ON THE PANEL 962VU (910VU),REMOVE RELAYS:
155 QA (154 QA)
BREAKERS.
D. ON PANEL 25VU:
(1) - PRESS PUSHBUTTON SWITCH FUEL/ENG1/
PUMP (FUEL/ENG2/PUMP)
CHECK THAT LEGENDS:
. RUN AND OFF ARE OFF.
- ON MFD UPPER WINDOW, IN ENGINE SD
PAGE, ITEM 1 IS DISPLAYED FOR
ENGINE 1(2)
(2) - PRESS PUSHBUTTON SWITCH FUEL/
X FEED, CHECK THAT LEGENDS:
. RUN OF ENG1 (2) PUMP
COME ON (PUMP ACTIVATED).
ENGINE 1(2) (PUMP ACTIVATED)
(3) - RELEASE PUSHBUTTON SWITCH FUEL/
X FEED
. RUN LEGENDS GOES OFF
ENG1 PUMP (ENG2 PUMP) DISAPPEARS.
*** CONTINUED ***
AH
28-23-00
OPT 10000-003
2-400 PAGE
9
DEC 01/14
28-23-00

OPT 10000-003
10
DEC14
2. A. ON THE PANEL 121VU, OPEN THE

1QA (2QA)
3QA (4QA)
B. ON 962VU (910VU), INSTALL RELAY:
155 QA (154 QA)
BREAKERS PREVIOUSLY OPENED.
011

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
012
_______________________
CLOSE-UP
OF FUEL SYSTEM
EQUIPMENT.
*****
AH
E N D
O F
T E X T
*****
28-23-00
OPT 10000-003
2-400 PAGE
10
DEC 01/14
28-23-00
11
AH
FUEL DISTRIBUTION
OPERATIONAL TEST
OPT 10000-003
DEC14
28-23-00
OPT 10000-003
2-400
PAGE
11
DEC 01/14
28-23-00
12
AH
OPT 10000-003
DEC14
28-23-00
OPT 10000-003
2-400
PAGE
12
DEC 01/14
28-23-00
13
AH
FUEL DISTRIBUTION
LEGEND
OPT 10000-003
DEC14
28-23-00
OPT 10000-003
2-400
PAGE
13
DEC 01/14
28-23-71

OF FUEL CROSSFEED VALVE
RAI 10000-001
1
MAR12
ZONING DATA
___________
ZONE
ACCESS
: 521
: 521DT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
MECHANIC
_________
MAN-HOURS
01
ELAPSED TIME
GSE

01 TORQUE WRENCH
SPARE
: 01 CROSSFEED VALVE
282370-06-070
EXPENDABLE
: 01
01
01
04
04
282370-06-050
282370-06-060
282370-06-030
282370-06-020
282370-06-010
SEAL
CIRCLIP
SEAL
WASHER
SCREW
PUBLICATION
___________
JIC
JIC
JIC

: OPERATIONAL TEST OF
CROSSFEED VALVE
AH
57-00-00-OAC-10000
28-23-00-OPT-10000
57-00-00-OAC-10000
28-23-71
RAI 10000-001
2-400 PAGE
1
MAR 01/12
28-23-71

001
RAI 10000-001
2
MAR12
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
1. MAKE CERTAIN THAT FUEL TANKS ARE DEFUELED
UNDER CROSSFEED VALVE.
2. DISPLAY WARNING NOTICE IN FLIGHT COMPARTMENT
3. INSTALL PLATFORM, 3,8 M ( (13 FT) TO GAIN
4. ON PANEL 121VU.
BREAKER:
2QE FUEL/FUEL FEED/XFEED
*** CONTINUED ***
AH
28-23-71
RAI 10000-001
2-400 PAGE
2
MAR 01/12
28-23-71

RAI 10000-001
3
MAR12
5. REMOVE ACCESS DOOR 521DT AS FOLLOWS :

003
_______________________________
OPENING
570000-OAC-10000
004
__________________________
REMOVAL
OF CROSSFEED VALVE
REF. FIG. 282371-RAI-00120
2. DISCONNECT BONDING STRIP.
3. DISCONNECT LINE (3).
4. REMOVE SEAL (2) AND BUSH (8),DISCARD
SEAL (2).
5. REMOVE SCREWS (4), WASHERS (5) RETAINING
CROSSFEED VALVE.
6. REMOVE CROSSFEED VALVE (1).
7. REMOVE AND DISCARD SEAL (6).
8. CAP OPEN LINE ENDS AND CONNECTOR ON REMOVED
EQUIPMENT.
9. PROTECT REMOVED COMPONENT INTERFACE AS WELL
AS ADJACENT AREA.
005
_______________________________
INSTALLATION
OF CROSSFEED VALVE
REF. FIG. 282371-RAI-00120
GREASE.
2. INSTALL CIRCLIP (8).
*** CONTINUED ***
AH
28-23-71
RAI 10000-001
2-400 PAGE
3
MAR 01/12
28-23-71

RAI 10000-001
4
MAR12
3. INSTALL NEW SEALS (2) AND (6).(SEALS SHOULD

BE LUBRICATED WITH CLEAN FUEL)
4. INSTALL CROSSFEED VALVE (1).
5. INSTALL SCREWS (4), WASHERS (5) AND TIGHTEN.
6. CONNECT LINE (3).
7. TORQUE NUT OF LINE (3) TO 0.5 M.DAN
(44.25 LBF.IN.).
8. CONNECT BONDING STRIP.
9. CONNECT ELECTRICAL CONNECTOR (7) TO CROSSFEED VALVE MOTOR.
006
OPERATIONAL TEST OF CROSSFEED

_____________________________
VALVE
_____
282300-OPT-10000
007
________
CLOSE-UP
1. ON PANEL 121VU,
REMOVE SAFETY CLIPS AND CLOSE CIRCUIT
BREAKER 2QE.
2. INSTALL ACCESS DOOR 521DT AS FOLLOWS :
008
________________________________
CLOSING
570000-OAC-10000
009
________
CLOSE-UP
*** CONTINUED ***
AH
28-23-71
RAI 10000-001
2-400 PAGE
4
MAR 01/12
28-23-71

RAI 10000-001
5
MAR12

6. REMOVE PLATFORM.
*****
AH
E N D
O F
T E X T
*****
28-23-71
RAI 10000-001
2-400 PAGE
5
MAR 01/12
28-23-71
6
AH
CROSSFEED VALVE
RAI 10000-001
MAR12
28-23-71
RAI 10000-001
2-400
PAGE
6
MAR 01/12
28-23-72

ACTUATOR
RAI 10000-001
1
MAR12
ZONING DATA
___________
ZONE
ACCESS
: 521
: 521DT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELECTRIC
___
MEN
_________
MAN-HOURS
01
ELAPSED TIME
GSE
SPARE
: 01 CROSSFEED VALVE ACTUATOR
282370-06-080
EXPENDABLE
: 01 PACKING
282371-01-070

CROSSFEED VALVE
57-00-00-OAC-10000
PUBLICATION
___________
JIC
JIC
AH
28-23-00-OPT-10000
28-23-72
RAI 10000-001
2-400 PAGE
1
MAR 01/12
28-23-72

ACTUATOR
001
RAI 10000-001
2
MAR12
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
1. MAKE CERTAIN THAT FUEL TANKS ARE DEFUELED
UNDER CROSSFEED VALVE.
3. INSTALL PLATFORM, 3,8 M ( (13 FT) TO GAIN
4. ON PANEL 121VU.
BREAKER:
2QE FUEL/FUEL FEED/XFEED
*** CONTINUED ***
AH
28-23-72
RAI 10000-001
2-400 PAGE
2
MAR 01/12
28-23-72

ACTUATOR
RAI 10000-001
3
MAR12
5. REMOVE ACCESS DOOR 521DT AS FOLLOWS :

003
_______________________________
OPENING
570000-OAC-10000
004
___________________________________
REMOVAL
OF CROSSFEED VALVE ACTUATOR
REF. FIG. 282372-RAI-00100
2. UNSCREW SCREWS RETAINING CLAMP AND REMOVE
CLAMP (3).
3. CAREFULLY REMOVE CROSSFEED VALVE ACTUATOR
(1) AND THE SAIL (4).
4. BLANK CROSSFEED VALVE ACTUATOR (1) END FITTING AND ELECTRICAL CONNECTOR.
5. BLANK CROSSFEED VALVE BODY END FITTING.
005
________________________________________
INSTALLATION
OF CROSSFEED VALVE ACTUATOR
REF. FIG. 282372-RAI-00100
1. CLEAN AND INSPECT COMPONENT INTERFACE AND/OR
ADJACENT AREA.
2. REMOVE BLANKING PLUG FROM CROSSFEED VALVE
ACTUATOR (1).
3. INSTALL ACTUATOR (1) ON CROSSFEED VALVE.
4. INSTALL SEAL (4),CLAMP (3) AND SCREW, RIB 2
SIDE. TIGHTEN.
5. CHECK FOR CORRECT CONDITION OF ELECTRICAL
CONNECTOR.
*** CONTINUED ***
AH
28-23-72
RAI 10000-001
2-400 PAGE
3
MAR 01/12
28-23-72

ACTUATOR
RAI 10000-001
4
MAR12

006
________
CLOSE-UP
1. ON PANEL 121VU,
REMOVE SAFETY CLIPS AND CLOSE CIRCUIT
BREAKER 2QE.
2. INSTALL ACCESS DOOR 521DT AS FOLLOWS :
007
________________________________
CLOSING
570000-OAC-10000
008
________
CLOSE-UP
6. REMOVE PLATFORM.
009
OPERATIONAL TEST OF CROSSFEED

_____________________________
VALVE
_____
282300-OPT-10000
*****
AH
E N D
O F
T E X T
*****
28-23-72
RAI 10000-001
2-400 PAGE
4
MAR 01/12
28-23-72
5
AH
CROSSFEED VALVE ACTUATOR
RAI 10000-001
MAR12
28-23-72
RAI 10000-001
2-400
PAGE
5
MAR 01/12
28-24-00
FUNCTIONAL TEST OF FUEL

LP VALVE
FUT 10000-002
1
DEC14
ZONING DATA
___________
ZONE
: 210
400
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
: 01 ENGINE ACCESS PLATFORM

01 CONTAINER
EXPENDABLE
: 00 SNAP WIRE
01 GUARANTEE SEAL
_________
MAN-HOURS
PUBLICATION
___________
JIC
JIC
SUPPLY
HINGED ENGINE COWLS
AH
24-46-00-EAD-10000
54-00-00-OAC-10000
28-24-00
FUT 10000-002
2-400 PAGE
1
DEC 01/14
28-24-00

LP VALVE
001
FUT 10000-002
2
DEC14
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
003
DE-ENERGIZATION OF SYSTEMS ACTUATED BY

______________________________________
FIRE-HANDLE
___________
1. ON PANEL 21VU,
3KF(4KF) ENG/ENG1(2) FEATH & AFU
2. ON PANEL 121VU
*** CONTINUED ***
AH
28-24-00
FUT 10000-002
2-400 PAGE
2
DEC 01/14

LP VALVE
28-24-00
FUT 10000-002
3
DEC14
A. OPEN THE FOLLOWING CIRCUIT BREAKER :

1HA(2HA) AIR BLEED/COMPT TEMP/ENG1(2)
BLEED/SO VALVES/BLEED
3. ON PANEL 122VU
1WD(2WD) SMOKE DRILL/ENG FIRE DET/
ENG 1(2)/LOOP A
3WD(4WD) ENG FIRE/WARN/ENG1(2)/FIRE/
HANDLE
ENG 1(2)/LOOP B
1DM
DE ICING/AAS/BOOTS A & B IND
28DM ANTI/DE ICING/SO & REG/VALVE 1 & 2
33PU MAIN ELEC PWR - DC/DC SVCE/UTLY
BUS CTL & CAUTION.
19XU(20XU) ACW ELEC PWR/GCU ACW GEN1(2)
PWR SPLY/GCU/ACW GEN1(2)
4. ON PANEL 129VU:
OPEN THE FOLLOWING CIRCUIT BREAKER
1KF(2KF)
PROP/FEATH PUMP/PWR SPLY/
ENG1(2)
5. INSTALL SAFETY TAGS.
004
DE-ENERGIZATION OF ENGINE FIRE EXTINGUISHING

____________________________________________
SYSTEM
______
BREAKERS :
- ON PANEL 122VU
1WE
2WE
3WE
ENG FIRE/EXTING CTL & IND/HOT SPLY/

L BTL SQUIBS
R BTL/SQUIBS
ENG FIRE/EXTING CTL & IND/EMER SPLY/
L BTL SQUIBS
*** CONTINUED ***
AH
28-24-00
FUT 10000-002
2-400 PAGE
3
DEC 01/14
28-24-00

LP VALVE
4WE
005
FUT 10000-002
4
DEC14

R BTL SQUIBS
___________
PREPARATION
1. ON UPPER CENTER INSTRUMENT PANEL 4VU, ON
FUEL QUANTITY INDICATOR, CHECK THAT EACH
FUEL TANK CONTAINS 500 KG (1102LBS) FUEL
MINIMUM.
NOTE : IF REQUIRED, TOP UP FUEL TANKS.
2. OPEN COWL 435AL(445AL) AS FOLLOWS
006
___________________________________
OPENING
OF LEFT LATERAL HINGED COWL
540000-OAC-10000
007
_______________
FUNCTIONAL
TEST
REF. FIG. 261200-OPT-00100
1. ON PANEL 20VU
PULL ENG 1(2) FIRE HANDLE
- ON PANEL 25VU, CROSS LINE FLOWBAR OF FUEL
ENG 1(2) LP VALVE LIGHT COMES ON.
- INSTALL WARNING NOTICE PROHIBITING ITS
OPERATION.
REF. FIG. 282400-FUT-00100
2. AT ENGINE
- INSTALL CONTAINER BELOW UNIONS (2), (3).
- LOOSEN UNIONS (2) AND (3).
- DISCONNECT LINE (1).
REF. FIG. 282100-OPT-00120
3. ON PANEL 25VU
A. PRESS FUEL/ENG1 (2)/PUMP PUSHBUTTON
*** CONTINUED ***
AH
28-24-00
FUT 10000-002
2-400 PAGE
4
DEC 01/14
28-24-00

LP VALVE
FUT 10000-002
5
DEC14
SWITCH (ELECTRIC PUMP OPERATES).

- RUN ENG 1 LEGEND ON
- OFF ENG 1 LEGEND OFF
- FEED LO/PR CAUTION LIGHT ON.
B. A FEW SECONDS LATER :
- RUN ENG 1 LEGEND OFF
- OFF ENG 1 LEGEND OFF
- FEED LO/PR CAUTION LIGHT OFF.
SYSTEM IS PRESSURIZED : LEAVE PRESSURIZED
DURING 3 OR 4 MINUTES.
4. AT ENGINE:
- CHECK THAT THERE IS NO LEAK ON DUCT
END (4).
- AT LEVEL OF DRAIN LOCATED AT LOWER PART OF
RIGHT COWL, CHECK THAT NO LEAK IS
OBSERVED.
5. ON PANEL 25VU, RELEASE FUEL/ENG1 (2)/PUMP
PUSHBUTTON SWITCH
- RUN ENG 1 LEGEND OFF
- OFF ENG 1 LEGEND ON.
6. AT ENGINE:
CONNECT LINE (1) TIGHTEN NUT (2).
WARNING:
THE FOLLOWING INSTRUCTIONS MUST BE RESPECTED
WHEN INSTALLING THE HOSE (1) :
- DO NOT HANDTIGHTEN ONE UNION ALONE.
- HANDTIGHTEN THE TWO UNIONS (2) AND (3)
LEAVING THE HOSE FREE TO MOVE.
- PROGRESSIVELY TORQUE THE TWO UNIONS IN
IN SEVERAL STEPS AT EACH END UNTIL THE
FINAL TORQUE.
7. ON PANEL 20VU:
A. PUSH ENG 1(2) FIRE HANDLE.
*** CONTINUED ***
AH
28-24-00
FUT 10000-002
2-400 PAGE
5
DEC 01/14

LP VALVE
28-24-00
FUT 10000-002
6
DEC14
- ON PANEL 25VU, IN LINE FLOWBAR OF FUEL

B. LOCK THE SAFETY GUARD OF ENGINE FIRE
HANDLES, MAKE THE SNAP-WIRE ON MECHANICAL
LOCKING SYSTEM AND PLACE THE GUARANTEE
SEAL.
008
_______________________________________________
ENERGIZATION
OF SYSTEMS ACTUATED BY FIRE-HANDLE
REMOVE SAFETY TAGS.
1. ON PANEL 21VU:
A. CLOSE THE FOLLOWING CIRCUIT BREAKERS :
- 3KF(4KF).
2. ON PANEL 121VU:
- 1HA(2HA)
3. ON PANEL 122VU:
- 1WE(2WE), 3WE(4WE), 1WD(2WD), 3WD(4WD)
5WD(6WD),1DM,28DM,33PU,19XU(20XU).
4. ON PANEL 129VU:
A. CLOSE THE FOLLOWING CIRCUIT BREAKER :
- 1KF(2KF).
009

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
*** CONTINUED ***

AH
28-24-00
FUT 10000-002
2-400 PAGE
6
DEC 01/14
28-24-00

LP VALVE
010
FUT 10000-002
7
DEC14
___________________________________
CLOSING
540000-OAC-10000
011
________
CLOSE-UP
EQUIPMENT.
3. REMOVE SMOKING PROHIBITED WARNING NOTICES
5. REMOVE PLATFORM.
*****
AH
E N D
O F
T E X T
*****
28-24-00
FUT 10000-002
2-400 PAGE
7
DEC 01/14
28-24-00
8
AH
ENG FIRE HANDLE
FUT 10000-002
DEC14
28-24-00
FUT 10000-002
2-400
PAGE
8
DEC 01/14
28-24-00
9
AH
TEST OF LP FUEL FIRE

SHUT OFF VALVE
FUT 10000-002
DEC14
28-24-00
FUT 10000-002
2-400
PAGE
9
DEC 01/14
28-24-00
10
AH
FUEL DISTRIBUTION
OPERATIONAL TEST
FUT 10000-002
DEC14
28-24-00
FUT 10000-002
2-400
PAGE
10
DEC 01/14
28-24-00

LP VALVE
FUT 10000-003
1
DEC14
ZONING DATA
___________
ZONE
: 210
400
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
: 01 ENGINE ACCESS PLATFORM

01 CONTAINER
EXPENDABLE
: 00 SNAP WIRE
01 GUARANTEE SEAL
_________
MAN-HOURS
PUBLICATION
___________
JIC
JIC
JIC

(DISPLAY UNITS
EXPLORATION)
SUPPLY
HINGED ENGINE COWLS
AH
31-63-00-PRO-10000
24-46-00-EAD-10000
54-00-00-OAC-10000
28-24-00
FUT 10000-003
2-400 PAGE
1
DEC 01/14
28-24-00

LP VALVE
001
FUT 10000-003
2
DEC14

___________________________________
EXPLORATION)
____________
_______________________
316300-PRO-10000
DISPLAY UNITS (DU).
002
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
*** CONTINUED ***

AH
28-24-00
FUT 10000-003
2-400 PAGE
2
DEC 01/14
28-24-00

LP VALVE
003
FUT 10000-003
3
DEC14

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
004

______________________________________
FIRE-HANDLE
___________
1. ON PANEL 21VU,
3KF(4KF) ENG CTL/ENG1(2)/FEATH/
CTL & AFU
2. ON PANEL 121VU
1HA(2HA) ENG1(2) BLEED/SO VALVE PWR
3. ON PANEL 122VU
ENG 1(2)/LOOP A
HANDLE
ENG 1(2)/LOOP B
1DM
DE ICING/ENG1 & 2 AND WINGS
BOOTS A & B IND
28DM DE ICING/SO & REG/VALVE 1 & 2
BUS CTL & CAUTION.
19XU(20XU) AC WILD ELEC PWR/CONT UNIT/
4. ON PANEL 129VU:
1KF(2KF)
ENG1(2)
*** CONTINUED ***
AH
28-24-00
FUT 10000-003
2-400 PAGE
3
DEC 01/14
28-24-00

LP VALVE
FUT 10000-003
4
DEC14

005

____________________________________________
SYSTEM
______
BREAKERS :
- ON PANEL 122VU
1WE
2WE
ENG FIRE/EXTING
L BTL SQUIBS
ENG FIRE/EXTING
R BTL/SQUIBS
ENG FIRE/EXTING
L BTL SQUIBS
ENG FIRE/EXTING
R BTL SQUIBS
3WE
4WE
006
CTL & IND/HOT SPLY/

CTL & IND/HOT SPLY/
CTL & IND/EMER SPLY/
___________
PREPARATION
CHECK THAT EACH FUEL TANK CONTAINS 500 KG
(1102LBS) FUEL MINIMUM.
NOTE : IF REQUIRED, TOP UP FUEL TANKS.
2. OPEN COWL 435AL(445AL) AS FOLLOWS
007
___________________________________
OPENING
540000-OAC-10000
008
_______________
FUNCTIONAL
TEST
REF. FIG. 261200-OPT-00100
1. ON PANEL 20VU
PULL ENG 1(2) FIRE HANDLE
- ON PANEL 25VU, CROSS LINE FLOWBAR OF FUEL
*** CONTINUED ***
AH
28-24-00
FUT 10000-003
2-400 PAGE
4
DEC 01/14
28-24-00

LP VALVE
FUT 10000-003
5
DEC14

FUEL LP 1(2) VALVE IS CLOSED.
- INSTALL WARNING NOTICE PROHIBITING ITS
OPERATION.
REF. FIG. 282400-FUT-00100
2. AT ENGINE
- INSTALL CONTAINER BELOW UNIONS (2), (3).
- LOOSEN UNIONS (2) AND (3).
- DISCONNECT LINE (1).
REF. FIG. 282100-OPT-00120
3. A. - ON PANEL 25VU, PRESS FUEL/ENG1 (2)/PUMP
OPERATES).
. RUN ENG 1 LEGEND ON
. OFF ENG 1 LEGEND OFF
. FEED LO/PR CAUTION LIGHT ON.
. ENG 1(2) ELECTRIC PUMP OPERATES (RUN)
. FEED LO PR MESSAGE IS DISPLAYED
B. A FEW SECONDS LATER :
- ON PANEL 25VU:
. RUN ENG 1 LEGEND OFF
. OFF ENG 1 LEGEND OFF
. FEED LO/PR CAUTION LIGHT OFF.
. ENG 1(2) ELECTRIC PUMP IS NEITHER
RUN NOR OFF.
. FEED LO PR MESSAGE NO MORE
DISPLAYED
SYSTEM IS PRESSURIZED : LEAVE PRESSURIZED
DURING 3 OR 4 MINUTES.
4. AT ENGINE:
- CHECK THAT THERE IS NO LEAK ON DUCT
END (4).
*** CONTINUED ***
AH
28-24-00
FUT 10000-003
2-400 PAGE
5
DEC 01/14
28-24-00

LP VALVE
FUT 10000-003
6
DEC14
- AT LEVEL OF DRAIN LOCATED AT LOWER PART OF

RIGHT COWL, CHECK THAT NO LEAK IS
OBSERVED.
5. - ON PANEL 25VU, RELEASE FUEL/ENG1 (2)/PUMP
PUSHBUTTON SWITCH
. RUN ENG 1 LEGEND OFF
. OFF ENG 1 LEGEND ON.
. ENG 1(2) ELECTRIC PUMP IS OFF
6. AT ENGINE:
CONNECT LINE (1) TIGHTEN NUT (2).
WARNING:
THE FOLLOWING INSTRUCTIONS MUST BE RESPECTED
WHEN INSTALLING THE HOSE (1) :
- DO NOT HANDTIGHTEN ONE UNION ALONE.
- HANDTIGHTEN THE TWO UNIONS (2) AND (3)
LEAVING THE HOSE FREE TO MOVE.
- PROGRESSIVELY TORQUE THE TWO UNIONS IN
IN SEVERAL STEPS AT EACH END UNTIL THE
FINAL TORQUE.
7. A. - ON PANEL 20VU, PUSH ENG 1(2) FIRE
HANDLE.
- ON PANEL 25VU, IN LINE FLOWBAR OF FUEL
FUEL LP 1(2) VALVE IS OPENED.
B. ON PANEL 20VU, LOCK THE SAFETY GUARD OF
ENGINE FIRE HANDLES, MAKE THE SNAP-WIRE
ON MECHANICAL LOCKING SYSTEM AND PLACE
THE GUARANTEE SEAL.
*** CONTINUED ***

AH
28-24-00
FUT 10000-003
2-400 PAGE
6
DEC 01/14
28-24-00

LP VALVE
009
FUT 10000-003
7
DEC14
_______________________________________________
ENERGIZATION
REMOVE SAFETY TAGS.
1. ON PANEL 21VU:
- 3KF(4KF).
2. ON PANEL 121VU:
- 1HA(2HA)
3. ON PANEL 122VU:
4. ON PANEL 129VU:
- 1KF(2KF).
010

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
011
___________________________________
CLOSING
540000-OAC-10000
012
________
CLOSE-UP
EQUIPMENT.
*** CONTINUED ***
AH
28-24-00
FUT 10000-003
2-400 PAGE
7
DEC 01/14
28-24-00

LP VALVE
FUT 10000-003
8
DEC14

3. REMOVE SMOKING PROHIBITED WARNING NOTICES
5. REMOVE PLATFORM.
*****
AH
E N D
O F
T E X T
*****
28-24-00
FUT 10000-003
2-400 PAGE
8
DEC 01/14
28-24-00
9
AH
ENG FIRE HANDLE
FUT 10000-003
DEC14
28-24-00
FUT 10000-003
2-400
PAGE
9
DEC 01/14
28-24-00
10
AH

SHUT OFF VALVE
FUT 10000-003
DEC14
28-24-00
FUT 10000-003
2-400
PAGE
10
DEC 01/14
28-24-00
11
AH
FUEL DISTRIBUTION
OPERATIONAL TEST
FUT 10000-003
DEC14
28-24-00
FUT 10000-003
2-400
PAGE
11
DEC 01/14
28-24-00
LEAKAGE TEST OF FUEL

FEED PIPES
FUT 10010-001
1
APR05
ZONING DATA
___________
ZONE
ACCESS
: 400
470
480
: 475AT 485AT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
MECHANIC
_________
MAN-HOURS
02
ELAPSED TIME
GSE
: 01 NITROGEN BOTTLE
01 PRESS GAUGE (0 TO 5 BAR)
01 ENGINE ACCESS PLATFORM
BULK MATERIAL : SOLVENT(11-004B)

GREASE (05-001A)
COMPOUND(08-004A)
AH
11-004
05-001
08-004
28-24-00
FUT 10010-001
2-400 PAGE
1
APR 01/05
28-24-00

FEED PIPES
001
FUT 10010-001
2
APR05
_______
WARNING
1. MAKE CERTAIN THAT NOBODY WORK ON FUEL SYSTEM
AND ON ENGINES.
2. ONLY USE EXPLOSION PROOF INSPECTION LIGHTS
AROUND WORKING AREA.
002
___________
PREPARATION
1. INSTALL PLATFORM TO GAIN ACCESS TO PANEL
475AT (485AT).
2. REMOVE AFT UPPER ENGINE COWLS 475AT (485AT)
AS FOLLOWS :
003
_____________________________________________
REMOVAL
OF AFT UPPER ENGINE COWL 475AT(485AT)
REF. FIG. 540000-RAI-00130
1. REMOVE SCREWS (31) AND (32).
2. REMOVE COWL.
3. CLEAN THE MATING FACE WITH NON METALLIC TOOL
AND SOLVENT MAT. N11-004B
004
_________________________________
LEAKAGE
TEST OF DOUBLE WALL TUBES
REF. FIG. 282400-FUT-00110
NOTA : AS THE LEAKAGE TEST IS IDENTICAL FOR
BOTH ENGINES, ONLY ONE TYPICAL TEST WILL
BE DESCRIBED.
1. UNSCREW COUPLINGS (1), (3), (4) AND (6).
*** CONTINUED ***
AH
28-24-00
FUT 10010-001
2-400 PAGE
2
APR 01/05
28-24-00

FEED PIPES
FUT 10010-001
3
APR05
2. REMOVE PIPES (2) AND (5).

3. CHECK THAT THERE IS NO FUEL LEAK ON COUPLINGS (7) AND (8).
4. CHECK THAT THERE IS NO LEAK ON PIPE (9).
5. CONNECT PIPE (9) SUCCESSIVELY ON COUPLINGS
(7) AND (8).
6. OPEN CYLINDER WITH PRESSURE ADJUSTED TO 2.5
BAR TO PRESSURIZE THE DOUBLE SKIN.
7. CLOSE CYLINDER.
8. LEAVE UNDER PRESSURE FOR 5 MN. CHECK THAT
THERE IS NO LEAK (PRESSURE FALL = 0).
9. DISCONNECT PIPE (9).
10.INSTALL PIPES (2) AND (5). TIGHTEN COUPLINGS
(1), (3), (4) AND (6).
11.MAKE CERTAIN THAT WORKING AREA IS CLEAN AND
EQUIPMENT.
12.INSTALL AFT UPPER ENGINE COWLS 475AT (485AT)
AS FOLLOWS :
005
INSTALLATION OF AFT UPPER ENGINE COWL 475AT

___________________________________________
(485AT)
_______
REF. FIG. 540000-RAI-00130
1. CHECK FOR CORRECT CONDITION OF COWL.
NOTE: - MAKE CERTAIN FOR PRESENCE OF WATER
REPELLENT PROTECTION ON COWLS 475AT
(485AT). IF NOT, MAKE THIS
PROTECTION (OR RESTORE IT) LIKE
*** CONTINUED ***
AH
28-24-00
FUT 10010-001
2-400 PAGE
3
APR 01/05
28-24-00

FEED PIPES
FUT 10010-001
4
APR05
PROCEDURE IN AMM 20-24-17.

- CHECK THAT BONDED CUPS INTO THE
COUNTERSUNK HOLES ARE NOT DAMAGED.
2. COAT UPPER PART OF CLIP SURFACE (33) WITH
MATERIAL NO. 05-001A (REF.20-31-00).
3. INSTALL COWL AND SECURE WITH SCREWS (31).
4. TIGHTEN SCREWS (32) (TIGHTENING TORQUE
CONTAINED BETWEEN 0.55 AND 0.65 M.DAN
(4.08 AND 4.8 FT.LBF)) MAKING CERTAIN THAT
CLEARANCE IN RELATION TO OTHER COWLS IS
UNIFORMLY DISTRIBUTED AROUND THE PERIPHERY.
5. RESTAURE SEALING BETWEEN UPPER SURFACE
PANEL AND ENGINE UPPER COWL WITH MATERIAL
NO.08-004A (REF. AMM 20.31.00).
006
________
CLOSE-UP
2. REMOVE ACCESS PLATFORM.
EQUIPMENT.
*****
AH
E N D
O F
T E X T
*****
28-24-00
FUT 10010-001
2-400 PAGE
4
APR 01/05
28-24-00
5
AH
LEAKAGE TEST
FUT 10010-001
APR05
28-24-00
FUT 10010-001
2-400
PAGE
5
APR 01/05
28-24-00
6
AH
AFT UPPER COWL
FUT 10010-001
APR05
28-24-00
FUT 10010-001
2-400
PAGE
6
APR 01/05
28-24-00
OPERATIONAL TEST OF LP

FUEL SHUT-OFF VALVE IND
OPT 10000-002
1
DEC14
ZONING DATA
___________
ZONE
ACCESS
: 210
433
443
475
485
: 435AL 445AL 475AT 485AT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
EXPENDABLE
: 00 SNAP-WIRE
01 GUARANTEE SEAL
_________
MAN-HOURS
PUBLICATION
___________
JIC
JIC
SUPPLY
AH
24-46-00-EAD-10000
54-00-00-RAI-10000
28-24-00
OPT 10000-002
2-400 PAGE
1
DEC 01/14
28-24-00

001
OPT 10000-002
2
DEC14
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
003

______________________________________
FIRE-HANDLE
___________
1. ON PANEL 21VU,
3KF(4KF) ENG/ENG1(2) FEATH & AFU
2. ON PANEL 121VU
*** CONTINUED ***
AH
28-24-00
OPT 10000-002
2-400 PAGE
2
DEC 01/14

28-24-00
OPT 10000-002
3
DEC14

1HA(2HA) AIR BLEED/COMPT TEMP/ENG1(2)
BLEED/SO VALVES/BLEED
3. ON PANEL 122VU
ENG 1(2)/LOOP A
HANDLE
ENG 1(2)/LOOP B
1DM
DE ICING/AAS/BOOTS A & B IND
28DM ANTI/DE ICING/SO & REG/VALVE 1 & 2
BUS CTL & CAUTION.
19XU(20XU) ACW ELEC PWR/GCU ACW GEN1(2)
4. ON PANEL 129VU:
1KF(2KF)
ENG1(2)
004

____________________________________________
SYSTEM
______
BREAKERS :
- ON PANEL 122VU
1WE
2WE
3WE

L BTL SQUIBS
R BTL/SQUIBS
L BTL SQUIBS
*** CONTINUED ***
AH
28-24-00
OPT 10000-002
2-400 PAGE
3
DEC 01/14
28-24-00

4WE
005
OPT 10000-002
4
DEC14

R BTL SQUIBS
___________
PREPARATION
1. POSITION A 3.8 M (13FT) PLATFORM TO GAIN
ACCESS TO ENGINE.
2. REMOVE ACCESS DOOR 475AT (485AT) AS FOLLOWS.
006
____________________________________________
REMOVAL
540000-RAI-10000
007
_________________________________
OPERATIONAL
TEST OF FUEL LP VALVE
REF. FIG 282100-OPT-00120
REF. FIG 261200-OPT-00100
REF. FIG 282161-RAI-00100
1. TEST OF LP FUEL FIRE SHUT OFF CONTROL SYSTEM
- CHECK THAT ENG 1(2) FIRE HANDLES 7WD AND
8WD ARE PUSHED.
2. ON CIRCUIT BREAKER PANEL 121VU, OPEN THE
3QG(4QG)
FUEL/LP VALVES/ENG1(2)/MOTOR 2
3. ON PANEL 20VU:
A. LOWER THE FIRE HANDLE, PULL DOWN THE
LOCKING HOLD-PLATE (SNAP-WIRE IS BREAKED)
PULL ENG 1 (2) FIRE HANDLE.
- ON FUEL/ENG 1 (2)/LP VALVE ANNUNCIATOR,
CROSS LINE FLOWBAR COMES ON.
B. ON ACTUATOR, CHECK THAT MECHANICAL INDEX
IS IN }F} POSITION (CLOSED)
C. PUSH ENG1 (2) FIRE HANDLE 7WD (8WD)
- ON FUEL/ENG 1(2) LP VALVE ANNUNCIATOR,
*** CONTINUED ***
AH
28-24-00
OPT 10000-002
2-400 PAGE
4
DEC 01/14
28-24-00

OPT 10000-002
5
DEC14
IN LINE FLOWBAR COMES ON.

D. ON ACTUATOR, CHECK THAT MECHANICAL INDEX
IS IN }O} POSITION (OPEN).
4. ON CIRCUIT BREAKER PANEL 121VU:
A. OPEN THE FOLLOWING CIRCUIT BREAKER.
1QG(2QG)
FUEL/LP VALVES/ENG1(2)/MOTOR 1
B. CLOSE CIRCUIT BREAKER 3QG (4QG)
C. PULL ENG 1(2) FIRE HANDLE 7WD (8WD)
- ON FUEL/ENG 1 (2)/LP VALVE ANNUNCIATOR,
IS IN }F} POSITION (CLOSED).
E. PUSH ENG1 (2) FIRE HANDLE 7WD (8WD)
- ON FUEL/ENG1 (2) LP VALVE ANNUNCIATOR,
LOCK THE HOLD-PLATE, INSTALL SNAP-WIRE
AND SECURE IT WITH GUARANTEE SEAL.
F. ON ACTUATOR, CHECK THAT MECHANICAL INDEX
IS IN O POSITION (OPEN).
5. ON CIRCUIT BREAKER PANEL, CLOSE CIRCUIT
BREAKER 1QG (2QG).
008
_______________________________________________
ENERGIZATION
REMOVE SAFETY TAGS.
1. ON PANEL 21VU:
- 3KF(4KF).
2. ON PANEL 121VU:
*** CONTINUED ***
AH
28-24-00
OPT 10000-002
2-400 PAGE
5
DEC 01/14
28-24-00

OPT 10000-002
6
DEC14

- 1HA(2HA)
3. ON PANEL 122VU:
4. ON PANEL 129VU:
- 1KF(2KF).
009
________
CLOSE
UP
INSTALL ACCESS DOOR 475AT (485AT) AS FOLLOWS.
010

_______________________________________
BY BOLTS
________
540000-RAI-10000
011

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
012
_______________________
CLOSE-UP
OF FUEL SYSTEM
EQUIPMENT.
*** CONTINUED ***
AH
28-24-00
OPT 10000-002
2-400 PAGE
6
DEC 01/14
28-24-00

OPT 10000-002
7
DEC14

*****
AH
E N D
O F
T E X T
*****
28-24-00
OPT 10000-002
2-400 PAGE
7
DEC 01/14
28-24-00
8
AH
FUEL DISTRIBUTION
OPERATIONAL TEST
OPT 10000-002
DEC14
28-24-00
OPT 10000-002
2-400
PAGE
8
DEC 01/14
28-24-00
9
AH
ENG FIRE HANDLE
OPT 10000-002
DEC14
28-24-00
OPT 10000-002
2-400
PAGE
9
DEC 01/14
28-24-00
10
AH
FUEL LP VALVE
OPT 10000-002
DEC14
28-24-00
OPT 10000-002
2-400
PAGE
10
DEC 01/14
28-24-00

OPT 10000-003
1
DEC14
ZONING DATA
___________
ZONE
ACCESS
: 210
433
443
475
485
: 435AL 445AL 475AT 485AT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
EXPENDABLE
: 00 SNAP-WIRE
01 GUARANTEE SEAL
_________
MAN-HOURS
PUBLICATION
___________
JIC
JIC
JIC

(DISPLAY UNITS
EXPLORATION)
SUPPLY
AH
31-63-00-PRO-10000
24-46-00-EAD-10000
54-00-00-RAI-10000
28-24-00
OPT 10000-003
2-400 PAGE
1
DEC 01/14
28-24-00

001
OPT 10000-003
2
DEC14

___________________________________
EXPLORATION)
____________
_______________________
316300-PRO-10000
DISPLAY UNITS (DU).
002
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
*** CONTINUED ***

AH
28-24-00
OPT 10000-003
2-400 PAGE
2
DEC 01/14
28-24-00

003
OPT 10000-003
3
DEC14

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
004

______________________________________
FIRE-HANDLE
___________
1. ON PANEL 21VU,
3KF(4KF) ENG CTL/ENG1(2)/FEATH/
CTL & AFU
2. ON PANEL 121VU
1HA(2HA) ENG1(2) BLEED/SO VALVE PWR
3. ON PANEL 122VU
ENG 1(2)/LOOP A
HANDLE
ENG 1(2)/LOOP B
1DM
DE ICING/ENG1 & 2 AND WINGS
BOOTS A & B IND
28DM DE ICING/SO & REG/VALVE 1 & 2
BUS CTL & CAUTION.
19XU(20XU) AC WILD ELEC PWR/CONT UNIT/
4. ON PANEL 129VU:
1KF(2KF)
ENG1(2)
*** CONTINUED ***
AH
28-24-00
OPT 10000-003
2-400 PAGE
3
DEC 01/14
28-24-00

OPT 10000-003
4
DEC14

005

____________________________________________
SYSTEM
______
BREAKERS :
- ON PANEL 122VU
1WE
2WE
3WE
4WE
006
ENG FIRE/EXTING
L BTL SQUIBS
ENG FIRE/EXTING
R BTL/SQUIBS
ENG FIRE/EXTING
L BTL SQUIBS
ENG FIRE/EXTING
R BTL SQUIBS
CTL & IND/HOT SPLY/

CTL & IND/HOT SPLY/
___________
PREPARATION
1. POSITION A 3.8 M (13FT) PLATFORM TO GAIN
ACCESS TO ENGINE.
2. REMOVE ACCESS DOOR 475AT (485AT) AS FOLLOWS.
007
____________________________________________
REMOVAL
540000-RAI-10000
008
_________________________________
OPERATIONAL
REF.
REF.
REF.
REF.
FIG.
FIG.
FIG.
FIG.
261200-OPT-00100
282100-OPT-00120
282161-RAI-00100
282000-OPT-00130
1. TEST OF LP FUEL FIRE SHUT OFF CONTROL SYSTEM

- CHECK THAT ENG 1(2) FIRE HANDLES 7WD AND
8WD ARE PUSHED.
*** CONTINUED ***
AH
28-24-00
OPT 10000-003
2-400 PAGE
4
DEC 01/14
28-24-00

OPT 10000-003
5
DEC14
2. ON CIRCUIT BREAKER PANEL 121VU, OPEN THE

3QG(4QG) FUEL/LP VALVES/ENG 1(2)/MOTOR 2
3. A. ON PANEL 20VU, LOWER THE FIRE HANDLE,
PULL DOWN THE LOCKING HOLD-PLATE (SNAPWIRE IS BREAKED) PULL ENG 1(2) FIRE
HANDLE.
- ON FUEL/ENG 1(2)/LP VALVE ANNUNCIATOR,
B. ON ACTUATOR, CHECK THAT MECHANICAL INDEX
IS IN }F} POSITION (CLOSED)
C. - ON PANEL 20VU, PUSH ENG 1(2) FIRE
HANDLE 7WD(8WD).
IS IN }O} POSITION (OPEN).
4. ON CIRCUIT BREAKER PANEL 121VU:
A. OPEN THE FOLLOWING CIRCUIT BREAKER.
1QG(2QG) FUEL/LP VALVES/ENG 1(2)/MOTOR 1
B. CLOSE CIRCUIT BREAKER 3QG(4QG)
C. ON PANEL 20VU, PULL ENG 1(2) FIRE HANDLE
7WD(8WD)
- ON FUEL/ENG 1(2) /LP VALVE ANNUNCIATOR
IS IN }F} POSITION (CLOSED).
*** CONTINUED ***
AH
28-24-00
OPT 10000-003
2-400 PAGE
5
DEC 01/14

28-24-00
OPT 10000-003
6
DEC14
E. ON PANEL 20VU, PUSH ENG 1(2) FIRE HANDLE

7WD(8WD)
LOCK THE HOLD-PLATE, INSTALL SNAP-WIRE
AND SECURE IT WITH GUARANTEE SEAL.
F. ON ACTUATOR, CHECK THAT MECHANICAL INDEX
IS IN O POSITION (OPEN).
5. ON CIRCUIT BREAKER PANEL, CLOSE CIRCUIT
BREAKER 1QG(2QG).
009
_______________________________________________
ENERGIZATION
REMOVE SAFETY TAGS.
1. ON PANEL 21VU:
- 3KF(4KF).
2. ON PANEL 121VU:
- 1HA(2HA)
3. ON PANEL 122VU:
4. ON PANEL 129VU:
- 1KF(2KF).
*** CONTINUED ***

AH
28-24-00
OPT 10000-003
2-400 PAGE
6
DEC 01/14
28-24-00

010
OPT 10000-003
7
DEC14
________
CLOSE
UP
INSTALL ACCESS DOOR 475AT (485AT) AS FOLLOWS.
011

_______________________________________
BY BOLTS
________
540000-RAI-10000
012

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
013
_______________________
CLOSE-UP
OF FUEL SYSTEM
EQUIPMENT.
*****
AH
E N D
O F
T E X T
*****
28-24-00
OPT 10000-003
2-400 PAGE
7
DEC 01/14
28-24-00
8
AH
FUEL DISTRIBUTION
OPERATIONAL TEST
OPT 10000-003
DEC14
28-24-00
OPT 10000-003
2-400
PAGE
8
DEC 01/14
28-24-00
9
AH
ENG FIRE HANDLE
OPT 10000-003
DEC14
28-24-00
OPT 10000-003
2-400
PAGE
9
DEC 01/14
28-24-00
10
AH
FUEL LP VALVE
OPT 10000-003
DEC14
28-24-00
OPT 10000-003
2-400
PAGE
10
DEC 01/14
28-24-00
11
AH
FUEL DISTRIBUTION
LEGEND
OPT 10000-003
DEC14
28-24-00
OPT 10000-003
2-400
PAGE
11
DEC 01/14
28-24-00
OPERATIONAL TEST OF THE

ENGINE SUPPLY HOSE FOR
LEAKAGE, ELEC PUMP ON
OPT 10010-001
1
DEC14
ZONING DATA
___________
ZONE
: 210
435
445
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
GSE
: 01 STEP LADDER
___
MEN
_________
MAN-HOURS
PUBLICATION
___________
JIC
SUPPLY
AH
24-46-00-EAD-10000
28-24-00
OPT 10010-001
2-400 PAGE
1
DEC 01/14
28-24-00

001
OPT 10010-001
2
DEC14
_______
WARNING
1. COMPLY WITH SAFETY INSTRUCTIONS OF ELECTRICAL POWER SUPLLY CHAPTER.
AROUND WORKING AREA.
3. ONLY USE EXPLOSION PROOF INSPECTION LIGHTS
002
___________
PREPARATION
1. MAKE CERTAIN THAT ALL CIRCUIT BREAKERS ARE
CLOSED.
2. ENERGIZE THE AIRCRAFT AS FOLLOWS :
3. OPEN ENGINE COWLS 445AL AND 435AL.
003

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
004
________________
OPERATIONAL
TEST
REF. FIG. 282400-OPT-00100
REF. FIG. 282400-FUT-00100
NOTE : THIS TEST IS PERFORMED TO CHECK ENGINE
FEED LP VALVE FOR LEAKAGE.
NOTE : AS LEAKAGE TEST OF ENGINE FEED LP VALVE
IS IDENTICAL ON EACH ENGINE, ONLY ONE
TYPICAL TEST WILL BE DESCRIBED.
1. ON UPPER PANEL 25VU, PRESS PUSHBUTTON SWITCH
FUEL/ENG1 (2)/PUMP
- RUN LEGEND ON
*** CONTINUED ***
AH
28-24-00
OPT 10010-001
2-400 PAGE
2
DEC 01/14
28-24-00

OPT 10010-001
3
DEC14
- OFF LEGEND OFF

AFTER A FEW SECONDS :
- FEED LO PR LEGEND OFF.
2. THE PUMP BEING IN OPERATION, CHECK THROUGH
THE DRAIN HOLE LOCATED ON RIGHT SIDE OF THE
BOTTOM STRUCTURE, THAT THERE IS NO LEAK OF
FUEL.
3. CHECK THAT THERE IS NO LEAK ON PIPE (1)
LOCATED BETWEEN FUEL HEATER AND INTERMEDIATE
FRAME. CHECK CORRECT CONDITION OF PIPE AND
THAT IT DOES NOT TOUCH THE ENGINE.
4. ON UPPER PANEL 25VU, PRESS AND RELEASE
PUSHBUTTON SWITCH FUEL/ENG1 (2)/PUMP
- RUN LEGEND OFF
- OFF LEGEND ON
5. CUT ELECTRICAL POWER SUPPLY AS FOLLOWS :
005

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
006
________
CLOSE
UP
EQUIPMENT.
2. PLACE THE AIRCRAFT IN THE INITIAL CONFIGURATION.
*****
AH
E N D
O F
T E X T
*****
28-24-00
OPT 10010-001
2-400 PAGE
3
DEC 01/14
28-24-00
4
AH
FUEL DRAINING IN BOTTOM

STRUCTURE
OPT 10010-001
DEC14
28-24-00
OPT 10010-001
2-400
PAGE
4
DEC 01/14
28-24-00
5
AH

SHUT OFF VALVE
OPT 10010-001
DEC14
28-24-00
OPT 10010-001
2-400
PAGE
5
DEC 01/14
28-24-61
FUEL LP VALVE
RAI 10000-001
1
MAR12
ZONING DATA
___________
ZONE
ACCESS
: 475
485
: 475AT 485AT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
SPARE
: 01 FUEL LP VALVE (MECA)

01 DUAL MOTOR ACTUATOR
282460-01-100
282460-01-040
EXPENDABLE
: 01
01
01
02
04
282460-01-030
282160-05-050
282160-05-060
282160-05
282160-05-110
O-RING
O-RING
O-RING
O-RING
O-RING
BULK MATERIAL : PURE MINERAL VASELINE

DRY LUBRICANT
_________
MAN-HOURS
04-012
06-001
PUBLICATION
___________
JIC
JIC
FUEL LP VALVE
AH
54-00-00-RAI-10000
28-24-00-OPT-10000
28-24-61
RAI 10000-001
2-400 PAGE
1
MAR 01/12
28-24-61
FUEL LP VALVE
001
RAI 10000-001
2
MAR12
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
1. MAKE CERTAIN THAT THERE IS NO FUEL IN FUEL
TANKS FOR REMOVAL OF FUEL LP VALVE (MECHANIC
AL PART).
3. ON PANEL 121VU,
BREAKERS :
1QG(2QG) FUEL/FUEL LP VALVES/ENG1(2)/MOTOR 1
3QG(4QG) FUEL/FUEL LP VALVES/ENG1(2)/MOTOR 2
*** CONTINUED ***
AH
28-24-61
RAI 10000-001
2-400 PAGE
2
MAR 01/12
28-24-61
FUEL LP VALVE
RAI 10000-001
3
MAR12

4. INSTALL ACCESS PLATFORM, 3 M (10 FT) TO GAIN
ACCESS TO ENGINE.
5. REMOVE ACCESS COWL 475AT(485AT) AS FOLLOW :
003
____________________________________________
REMOVAL
540000-RAI-10000
004
REMOVAL OF FUEL LP VALVE DUAL MOTOR

___________________________________
ACTUATOR
________
REF. FIG. 282161-RAI-00100
1. DISCONNECT ELECTRICAL CONNECTORS (1) AND (2)
2. REMOVE SCREW (4) AND NUT (3) FROM CLAMP (5).
3. REMOVE CLAMP (5).
4. REMOVE DUAL MOTOR ACTUATOR (6).
5. BLANK ELECTRICAL CONNECTORS.
6. BLANK ORIFICES AND CONNECTORS OF REMOVED
EQUIPMENT.
005
________________________
REMOVAL
OF FUEL LP VALVE
REF. FIG. 282461-RAI-00100
NOTE : AS REMOVAL OF COUPLINGS B IS IDENTICAL, ONLY ONE TYPICAL REMOVAL WILL BE
TREATED. NEVERTHELESS, IN ORDER TO
FACILITATE REMOVAL OF FUEL LP VALVE, IT
IS NECESSARY TO DISCONNECT SIMULTANEOUSLY BOTH COUPLINGS B.
*** CONTINUED ***
AH
28-24-61
RAI 10000-001
2-400 PAGE
3
MAR 01/12
28-24-61
FUEL LP VALVE
RAI 10000-001
4
MAR12

2. DISCONNECT BONDING STRIPS (2) OF ELBOWS
(3) AND (13).
3. UNSCREW NUT (14), MOVE SLEEVE (17) BACK.
COLLECT ADAPTERS (16) AND (21).
4. SLIDE SPACER (18).
5. DISCONNECT BONDING STRIP (19).
6. UNSCREW NUT (20).
7. REMOVE FASTENERS (12) AND (4).
8. MOVE ELBOW (3) BACK AND REMOVE FUEL LP
VALVE (7).
9. DISCONNECT LINE (1) FROM COUPLINGS B.
COLLECT RING (23).
10.DISCARD SEALS (5), (6), (8), (15), (22) AND
(25).
11.BLANK ORIFICES, TANK AND ELBOW (13) SIDES.
12.REMOVE PRESSURE SWITCH (10). DISCARD SEAL
(9).
006
_____________________________
INSTALLATION
OF FUEL LP VALVE
REF. FIG. 282461-RAI-00100
REMOVAL.
2. INSTALL NEW SEALS (5), (6) AND (8). (SEALS
MUST BE PREVIOUSLY LUBRICATED WITH CLEAN
FUEL).
*** CONTINUED ***
AH
28-24-61
RAI 10000-001
2-400 PAGE
4
MAR 01/12
28-24-61
FUEL LP VALVE
RAI 10000-001
5
MAR12
3. INSTALL FASTENERS (4). TIGHTEN.

4. INSTALL NEW SEAL (25) BETWEEN CLIPS (24) AND
(26) (SEAL MUST BE PREVIOUSLY LUBRICATED IN
CLEAN FUEL).
5. INSTALL RING (23) INSIDE INNER LINE.
6. COMPRESS FUEL LP VALVE/LINE/ELBOW ASSEMBLY.
POSITION IT ON ITS LOCATION.
7. INSTALL FASTENERS (12). TIGHTEN.
8. INSTALL CLIPS (24), (26) AND SEAL (25) IN
CONTACT WITH RING (23).
9. APPLY DRY LUBRICANT ON NUT (20) THREADS.
TORQUE NUT (20) TO 0.4 M.DAN.
10.CONNECT BONDING STRIP (19).
11.INSTALL NEW SEALS (15) AND (22) (SEALS MUST
BE PREVIOUSLY LUBRICATED IN CLEAN FUEL).
12.MOVE SPACER (18) FORWARD.
13.MOVE SLEEVE (17) FORWARD. INSTALL ADAPTERS
(21). CONTINUE TO MOVE SLEEVE (17) FORWARD
IN ORDER TO RETAIN ADAPTERS (21) AND SPACER
(18).
14.INSTALL ADAPTERS (16). APPLY DRY LUBRICANT
ON NUT (14) THREADS AND TORQUE NUT (14) TO
0.7 M.DAN.
15.CONNECT BONDING STRIPS (2) ON B COUPLINGS
AND LINE (1).
16.INSTALL A NEW SEAL (9) ON PRESSURE SWITCH
(10) (SEAL MUST BE PREVIOUSLY LUBRICATED IN
CLEAN FUEL).
*** CONTINUED ***
AH
28-24-61
RAI 10000-001
2-400 PAGE
5
MAR 01/12
28-24-61
FUEL LP VALVE
RAI 10000-001
6
MAR12
17.INSTALL PRESSURE SWITCH (10).

18.CONNECT ELECTRICAL CONNECTOR (11).
007
INSTALLATION OF FUEL LP VALVE DUAL MOTOR

________________________________________
ACTUATOR
________
REF. FIG. 282161-RAI-00100
1. PREPARATION OF REPLACEMENT COMPONENT (IF REQUIRED).
2. INSTALL DUAL MOTOR ACTUATOR (6).
3. INSTALL CLAMP (5).
4. INSTALL SCREW (4), NUT (3) AND TIGHTEN.
5. CONNECT ELECTRICAL CONNECTORS (1) AND (2).
008
________
CLOSE-UP
1. ON PANEL 121VU,
CIRCUIT BREAKERS :
009

_______________________________________
BY BOLTS
________
540000-RAI-10000
010
________
CLOSE-UP
*** CONTINUED ***
AH
28-24-61
RAI 10000-001
2-400 PAGE
6
MAR 01/12
28-24-61
FUEL LP VALVE
RAI 10000-001
7
MAR12
6. REMOVE PLATFORM.
011
_________________________________
OPERATIONAL
282400-OPT-10000
*****
AH
E N D
O F
T E X T
*****
28-24-61
RAI 10000-001
2-400 PAGE
7
MAR 01/12
28-24-61
8
AH
FUEL LP VALVE
RAI 10000-001
MAR12
28-24-61
RAI 10000-001
2-400
PAGE
8
MAR 01/12
28-24-61
9
AH
FUEL LP VALVE
RAI 10000-001
MAR12
28-24-61
RAI 10000-001
2-400
PAGE
9
MAR 01/12
28-24-62
FUEL LP VALVE ACTUATOR
RAI 10000-001
1
MAR12
ZONING DATA
___________
ZONE
ACCESS
: 475
485
: 475AT 485AT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
_________
MAN-HOURS
ELAPSED TIME
GSE
SPARE
: 01 DUAL MOTOR ACTUATOR
282460-01-040
FUEL LP VALVE
54-00-00-RAI-10000
PUBLICATION
___________
JIC
JIC
AH
28-24-00-OPT-10000
28-24-62
RAI 10000-001
2-400 PAGE
1
MAR 01/12
28-24-62
001
RAI 10000-001
2
MAR12
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
1. POSITION A 4M (13FT.) ACCESS PLATFORM TO
GAIN ACCESS TO ENGINE.
2. MAKE CERTAIN THAT ENG1 (ENG2) FUEL LP VALVES
9QG (10QG) ARE CLOSED.
3. DISPLAY A WARNING NOTICE IN FLIGHT COMPARTMENT TO PROHIBIT ENERGIZATION OF FUEL
SYSTEM.
4. ON PANEL 121VU,
BREAKERS :
*** CONTINUED ***
AH
28-24-62
RAI 10000-001
2-400 PAGE
2
MAR 01/12
28-24-62
RAI 10000-001
3
MAR12

5. REMOVE ACCESS COWL 475AT(485AT) AS FOLLOWS :
003
____________________________________________
REMOVAL
540000-RAI-10000
004
REMOVAL OF FUEL LP VALVE DUAL MOTOR

___________________________________
ACTUATOR
________
REF. FIG. 282161-RAI-00100
1. DISCONNECT ELECTRICAL CONNECTORS (1) AND (2)
2. REMOVE SCREW (4) AND NUT (3) FROM CLAMP (5).
3. REMOVE CLAMP (5).
4. REMOVE DUAL MOTOR ACTUATOR (6).
5. BLANK ELECTRICAL CONNECTORS.
6. BLANK ORIFICES AND CONNECTORS OF REMOVED
EQUIPMENT.
005
INSTALLATION OF FUEL LP VALVE DUAL MOTOR

________________________________________
ACTUATOR
________
REF. FIG. 282161-RAI-00100
1. PREPARATION OF REPLACEMENT COMPONENT (IF REQUIRED).
2. INSTALL DUAL MOTOR ACTUATOR (6).
3. INSTALL CLAMP (5).
*** CONTINUED ***
AH
28-24-62
RAI 10000-001
2-400 PAGE
3
MAR 01/12
28-24-62
RAI 10000-001
4
MAR12
4. INSTALL SCREW (4), NUT (3) AND TIGHTEN.

5. CONNECT ELECTRICAL CONNECTORS (1) AND (2).
006
________
CLOSE-UP
1. ON PANEL 121VU,
CIRCUIT BREAKERS :
007

_______________________________________
BY BOLTS
________
540000-RAI-10000
008
________
CLOSE-UP
6. REMOVE PLATFORM.
009
_________________________________
OPERATIONAL
282400-OPT-10000
*****
AH
E N D
O F
T E X T
*****
28-24-62
RAI 10000-001
2-400 PAGE
4
MAR 01/12
28-24-62
5
AH
FUEL LP VALVE
RAI 10000-001
MAR12
28-24-62
RAI 10000-001
2-400
PAGE
5
MAR 01/12
28-25-51
REFUEL/DEFUEL VALVE IN
LANDING GEAR FAIRING
RAI 10000-001
1
MAR12
ZONING DATA
___________
ZONE
ACCESS
: 196
614
: 196ES
614AB
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
SPARE
: 01 REFUELING VALVE
EXPENDABLE
: 01 SEAL
AH
___
MEN
_________
MAN-HOURS
28-25-51
RAI 10000-001
2-400 PAGE
1
MAR 01/12
28-25-51
001
RAI 10000-001
2
MAR12
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
1. ON PANEL 121 VU
OPEN FOLLOWING CIRCUIT BREAKER :
2QU
FUEL/FUELLING CTL & IND
2. REMOVE PANEL 196ES.
003
___________________________________
REMOVE
OF REFUELING DEFUELING VALVE
REF. FIG. 282551-RAI-00100
1. REMOVE FASTENER (5) OF THE RETAINING CABLE
OF BLANKING CAP (6).
*** CONTINUED ***
AH
28-25-51
RAI 10000-001
2-400 PAGE
2
MAR 01/12
28-25-51
RAI 10000-001
3
MAR12
2. UNSCREW AND REMOVE NUTS (3),

RECOVER WASHERS (2).
3. REMOVE VALVE (4).
4. DISCARD SEAL (7) LOCATED ON PIPING
FLANGE (1).
004
_________________________________________
INSTALLATION
OF REFUELING DEFUELING VALVE
REF. FIG. 282551-RAI-00100
1. INSTALL NEW SEAL (7) ON PIPING FLANGE (1).
2. INSTALL REFUELING VALVE (4) ON ITS LOCATION.
3. SCREW THE SCREWS (3) WITH WASHERS (2).
4. CONNECT RETAINING CABLE OF BLANKING CAP (6)
BY MEANS FASTENER (5).
005
________
CLOSE-UP
CLEAR OF TOOLS AND MISCELLANEOUS ITEMS.
2. INSTALL PANEL 196ES.
3. ON PANEL 121 VU
CLOSE FOLLOWING CIRCUIT BREAKER :
2QU
FUEL/FUELLING CTL & IND
006
____________________________
CHECK
OF REFUEL/DEFUEL VALVE
1. DURING REFUELING OR DEFUELING OPERATION,
CARRY OUT THE FOLLOWING :
A. CHECK REFUEL/DEFUEL VALVE FOR CORRECT
OPERATION
B. LEAKAGE CHECK.
*****
AH
E N D
O F
T E X T
*****
28-25-51
RAI 10000-001
2-400 PAGE
3
MAR 01/12
28-25-51
4
AH
REFUEL/DEFUEL VALVE
RAI 10000-001
MAR12
28-25-51
RAI 10000-001
2-400
PAGE
4
MAR 01/12
28-25-52

OF REFUELING CONTROL
PANEL (RCP)
RAI 10000-001
1
DEC14
ZONING DATA
___________
ZONE
ACCESS
: 192
: 192JR
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
_________
MAN-HOURS
ELAPSED TIME
SPARE
: 01 REFUEL CONTROL PANEL
282580
: POWER SUPPLY FROM

BATTERIES
24-31-00-EAD-10000
PUBLICATION
___________
JIC
AH
28-25-52
RAI 10000-001
2-400 PAGE
1
DEC 01/14
28-25-52

PANEL (RCP)
001
RAI 10000-001
2
DEC14
_______
WARNING
WARNING C.D.C.C.L.
CONTROL LIMITATION
CONTROL LIMITATION.
CONFIGURATION.
002
___________
PREPARATION
1. ON PANEL 121VU, OPEN, SAFETY AND TAG THE
1QT FUEL/FCU CHAN1
2QT FUEL/FCU CHAN2
2QU FUEL/FUELING CTL & IND
2. OPEN ACCESS DOOR 192JR.
003
__________________________________
REMOVAL
OF REFUELING CONTROL PANEL
REF. FIG. 282552-RAI-00100
1. UNLOOSE THE SCREWS (2) SECURING THE
REFUELING CONTROL PANEL (1).
2. EXTRACT THE REFUELING CONTROL PANEL (1).
3. UNPLUG THE ELECTRICAL CONNECTOR (3).
4. PUT BLANKING CAP ON THE ELECTRICAL
CONNECTOR.
*** CONTINUED ***
AH
28-25-52
RAI 10000-001
2-400 PAGE
2
DEC 01/14
28-25-52

PANEL (RCP)
004
RAI 10000-001
3
DEC14
_______________________________________
INSTALLATION
OF REFUELING CONTROL PANEL
REF. FIG. 282552-RAI-00100
1. REMOVE BLANKING CAP FROM ELECTRICAL
CONNECTOR (3).
2. PLUG IN ELECTRICAL CONNECTOR TO THE
3. INSERT THE REFUELING CONTROL PANEL IN
THE PANEL STRUCTURE.
4. TIGHTEN SCREWS (2) TO SECURE
005
________
CLOSE-UP
1. ON PANEL 121VU REMOVE SAFETY CLIPS AND
TAGS AND CLOSE CIRCUIT BREAKERS PREVIOUSLY
OPENED.
006
_________________________________
ENERGIZING
OF SYSTEM FROM BATTERY
243100-EAD-10000
007
FUNCTIONAL TEST OF
__________________
REFUELING CONTROL PANEL
_______________________
(RCP)
_____
CHECK THAT VALUES ARE THE SAME :
- ON ENGINE SECONDARY PAGE (MFD UPPER WINDOW),
- AND ON REFUELING CONTROL PANEL 100QU.
008
____________________________________
DE-ENERGIZING
243100-EAD-10000
*** CONTINUED ***

AH
28-25-52
RAI 10000-001
2-400 PAGE
3
DEC 01/14
28-25-52

PANEL (RCP)
009
RAI 10000-001
4
DEC14
________
CLOSE-UP
1. MAKE CERTAIN THAT WORKING AREA IS CLEAN
AND CLEAR OF TOOLS AND MISCELLANEOUS ITEMS
OF EQUIPMENT.
2. CLOSE ACCESS DOOR PREVIOUSLY OPENED.
*****
AH
E N D
O F
T E X T
*****
28-25-52
RAI 10000-001
2-400 PAGE
4
DEC 01/14
28-25-52
5
AH
REFUELING CONTROL PANEL
RAI 10000-001
DEC14
28-25-52
RAI 10000-001
2-400
PAGE
5
DEC 01/14
28-25-71

ASSEMBLY
RAI 10000-001
1
MAR12
ZONING DATA
___________
ZONE
ACCESS
: 290
: 295BL 296CR
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
SPARE
: 01 REFUEL VALVE
282570-30-070
EXPENDABLE
: 01
01
01
02
06
282570-32-050
282570-28-040
282570-28-050
282570-30-060
282570-30-030
SEAL
SEAL
SEAL
SEALS
WASHERS
BULK MATERIAL : PETROLATUM AIR 3565A
_________
MAN-HOURS
04-012
PUBLICATION
___________
JIC
JIC

OF WING-TO-FUSELAGE
FAIRINGS
: REFUELING
AH
53-93-00-RAI-10000
12-11-00-FLG-10020
28-25-71
RAI 10000-001
2-400 PAGE
1
MAR 01/12
28-25-71

ASSEMBLY
001
RAI 10000-001
2
MAR12
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
1. RELEASE FOLLOWING CIRCUIT BREAKER :
2QU
FUEL/FUELING/CTL & IND.
2. REMOVE PANELS 295 BL AND 296 CR, BY USING
THE PROCEDURE DESCRIBED BELOW:
003
____________________________________
REMOVAL
539300-RAI-10000
*** CONTINUED ***

AH
28-25-71
RAI 10000-001
2-400 PAGE
2
MAR 01/12
28-25-71

ASSEMBLY
004
RAI 10000-001
3
MAR12
________________________________________
REMOVAL
OF FUEL REFUELING VALVE ASSEMBLY
REF.FIG 282571 RAI 00100
1. REMOVE CLAMPS (4) OF PIPE (3).
2. UNSCREW NUT (15), PUSH BACK (3).
3. DISCONNECT ELECTRICAL CONNECTORS (5).
4. REMOVE FASTENERS (7) OF THE ADAPTER FLANGE
(8).
5. UNSCREW NUT (9), PUSH BACK PIPE (10) AND
REMOVE ADAPTER (8).
6. DISCARD SEALS (6) AND (11).
7. REMOVE FASTENERS (12).
8. REMOVE FUEL REFUEL/DEFUEL VALVE ASSEMBLY.
9. DISCARD SEALS (13) AND (14).
005
INSTALLATION OF FUEL REFUELING

______________________________
DEFUELING VALVE ASSEMBLY
________________________
REF.FIG 282571 RAI 00100
1. INSTALL NEW SEALS (13) AND (4).
2. INSTALL REFUEL/DEFUEL COUPLING (16) ON ITS
LOCATION.
3. INSTALL FASTENERS (12), TIGHTEN.
4. INSTALL CONNECTOR (1) PROVIDED OF ITS SEAL
(2).
5. CONNECT PIPE (3), TIGHTEN NUT (15).
*** CONTINUED ***
AH
28-25-71
RAI 10000-001
2-400 PAGE
3
MAR 01/12
28-25-71

ASSEMBLY
RAI 10000-001
4
MAR12
6. INSTALL CLAMPS (4) OF PIPE (3).

7. PLACE JOINTS (6) AND (11).
8. CONNECT PIPE (8), INSTALL FASTENERS (7),
TIGHTEN.
9. SCREW NUT (9), TIGHTEN.
10.CONNECT ELECTRICAL CONNECTORS (5).
006
________
CLOSE
UP
1. MAKE CERTAIN WORKING AREA IS CLEAN AND CLEAR
OF TOOLS AND MISCELLANEOUS ITEMS OF
EQUIPMENTS.
2. CLOSE FOLLOWING CIRCUIT BREAKER :
- 2QU FUEL/FUELING/CTL 2IND.
3. INSTALL PANELS 295BL AND 296 CR :
- SEE JOB INSTRUCTION CARD 539300 RAI 10000.
007
_________________________________________
INSTALLATION
539300-RAI-10000
008
________
CLOSE-UP
*** CONTINUED ***
AH
28-25-71
RAI 10000-001
2-400 PAGE
4
MAR 01/12
28-25-71

ASSEMBLY
RAI 10000-001
5
MAR12

6. REMOVE PLATFORM.
009
_________
REFUELING
121100-FLG-10020
*****
AH
E N D
O F
T E X T
*****
28-25-71
RAI 10000-001
2-400 PAGE
5
MAR 01/12
28-25-71
6
AH
FUEL REFUEL/DEFUEL
VALVE ASSEMBLY
RAI 10000-001
MAR12
28-25-71
RAI 10000-001
2-400
PAGE
6
MAR 01/12
28-25-71

OF REFUEL/DEFUEL
ELECTROVALVE
RAI 10010-001
1
MAR12
ZONING DATA
___________
ZONE
ACCESS
: 290
614
: 295BL 296CR
614AB
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
_________
MAN-HOURS
ELAPSED TIME
SPARE
: 01 VALVE (L/R) REFUELLING
282571-01
EXPENDABLE
: 02 O-RING
04 SREW
04 WASHER
282571-01
282571-01
282571-01

OF WING-TO-FUSELAGE
FAIRINGS
: REFUELING
53-93-00-RAI-10000
PUBLICATION
___________
JIC
JIC
AH
12-11-00-FLG-10020
28-25-71
RAI 10010-001
2-400 PAGE
1
MAR 01/12
28-25-71

OF REFUEL/DEFUEL
ELECTROVALVE
001
RAI 10010-001
2
MAR12
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
1. RELEASE FOLLOWING CIRCUIT BREAKER :
2QU
FUEL/FUELING/CTL & IND.
2. REMOVE PANELS 295 BL AND 296 CR, BY USING
THE PROCEDURE DESCRIBED BELOW:
003
____________________________________
REMOVAL
539300-RAI-10000
*** CONTINUED ***

AH
28-25-71
RAI 10010-001
2-400 PAGE
2
MAR 01/12
28-25-71

OF REFUEL/DEFUEL
ELECTROVALVE
004
RAI 10010-001
3
MAR12
______________________________
REMOVAL
REF. FIG.282571-RAI-00110
2. REMOVE THE FOUR SCREWS (6) AND WASHERS (5).
3. REMOVE REFUEL/DEFUEL VALVE (4) FROM BODY
(1).
4. REMOVE 0-RINGS (2) AND (3) FROM THEIR RESPECTIVE GROOVE.
5. INSTALL PROTECTIVE PLUGS.
005
INSTALLATION OF REFUEL/DEFUEL VALVE

___________________________________
(LEFT OR RIGHT)
_______________
REF. FIG. 282571-RAI-00110.
1. REMOVE PROTECTIVE PLUGS.
2. INSTALL THE TWO O RINGS (2) AND (3) IN THEIR
RESPECTIVE GROOVE.
3. INSTALL VALVE ASSEMBLY (4) ON BODY (1).
4. SCREW AND TIGHTEN THE FOUR SCREWS (6)
EQUIPPED WITH WASHERS (5).
5. CONNECT ELECTRICAL CONNECTORS (7).
(FOOLPROOFING DIVICE PREVENTS CROSS-CONNECTION OF LEFT AND RIGHT CONNECTORS).
006
________
CLOSE
UP
1. MAKE CERTAIN WORKING AREA IS CLEAN AND CLEAR
OF TOOLS AND MISCELLANEOUS ITEMS OF
EQUIPMENTS.
*** CONTINUED ***
AH
28-25-71
RAI 10010-001
2-400 PAGE
3
MAR 01/12
28-25-71

OF REFUEL/DEFUEL
ELECTROVALVE
RAI 10010-001
4
MAR12
2. CLOSE FOLLOWING CIRCUIT BREAKER :

- 2QU FUEL/FUELING/CTL 2IND.
3. INSTALL PANELS 295BL AND 296 CR :
- SEE JOB INSTRUCTION CARD 539300 RAI 10000.
007
_________________________________________
INSTALLATION
539300-RAI-10000
008
____________________________
CHECK
1. DURING REFUELING OR DEFUELING OPERATION,
CARRY OUT THE FOLLOWING :
A. CHECK REFUEL/DEFUEL VALVE FOR CORRECT
OPERATION
B. LEAKAGE CHECK.
009
_________
REFUELING
121100-FLG-10020
*****
AH
E N D
O F
T E X T
*****
28-25-71
RAI 10010-001
2-400 PAGE
4
MAR 01/12
28-25-71
5
AH
ELECTROVALVE
REFUEL/DEFUEL
RAI 10010-001
MAR12
28-25-71
RAI 10010-001
2-400
PAGE
5
MAR 01/12
28-25-73
DETAILED VISUAL
INSPECTION OF HIGH
LEVEL SENSOR
DVI 10000-001
1
MAR12
ZONING DATA
___________
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
___
MEN
_________
MAN-HOURS
PUBLICATION
___________
JIC
HIGH LEVEL SENSOR
AH
28-25-73-RAI-10000
28-25-73
DVI 10000-001
2-400 PAGE
1
MAR 01/12
28-25-73
DETAILED VISUAL
INSPECTION OF HIGH
LEVEL SENSOR
001
DVI 10000-001
2
MAR12
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
NOTE:
REMOVE HIGH LEVEL SENSOR WITHOUT DISCONNECT
ELECTRICAL CONNECTOR AND CLAMPS.
003
____________________________
REMOVAL
OF HIGH LEVEL SENSOR
282573-RAI-10000
004

_____________________________
HIGH LEVEL SENSOR
_________________
REF. FIG. 282573 RAI 00100
*** CONTINUED ***
AH
28-25-73
DVI 10000-001
2-400 PAGE
2
MAR 01/12
28-25-73
DETAILED VISUAL
INSPECTION OF HIGH
LEVEL SENSOR
DVI 10000-001
3
MAR12
CHECK THAT :
- WIRES ARE NOT BROKEN ESPECIALLY AT
CONNECTION.
005
_________________________________
INSTALLATION
282573-RAI-10000
006
________
CLOSE-UP
6. REMOVE PLATFORM.
*****
AH
E N D
O F
T E X T
*****
28-25-73
DVI 10000-001
2-400 PAGE
3
MAR 01/12
28-25-73
4
AH
HIGH LEVEL SENSOR
DVI 10000-001
MAR12
28-25-73
DVI 10000-001
2-400
PAGE
4
MAR 01/12
28-25-73
FUNCTIONAL TEST OF HIGH

LEVEL SENSOR AND AUTO
CLOSURE OF VALVES
FUT 10000-001
1
DEC14
ZONING DATA
___________
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
_________
MAN-HOURS
PUBLICATION
___________
JIC
SUPPLY
AH
24-46-00-EAD-10000
28-25-73
FUT 10000-001
2-400 PAGE
1
DEC 01/14
28-25-73

CLOSURE OF VALVES
001
FUT 10000-001
2
DEC14
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
003
___________
PREPARATION
2. POSITION ACCESS PLATFORM.
*** CONTINUED ***

AH
28-25-73
FUT 10000-001
2-400 PAGE
2
DEC 01/14
28-25-73

CLOSURE OF VALVES
004
FUT 10000-001
3
DEC14
_____________________________________
FUNCTIONAL
TEST OF HIGH LEVEL SENSORS
REF. FIG. 282573-FUT-00120
1. CHECK CORRECT OPERATION OF HIGH LEVEL
SENSORS.
A. ON REFUELING PANEL 5004VU:
(1)PLACE REFUELING/REFUEL/OFF/DEFUEL
SWITCH IN REFUEL POSITON.
(2)PLACEREFUELING/REFUEL VALVE/LH AND RH
SWITCHES IN OPEN POSITION
- REFUELING/VALVE LH/RH OPEN LIGHTS
COME ON.
- HIGH LEVEL/TANK1 AND TANK2 LIGHTS
ARE OFF.
NOTE : IN THE OPPOSITE CASE PERFORM A
PARTIAL DEFUELING.
(AMM: 121128-DFG-10000).
B. REFUEL, BY TANK, ABOVE MAXIMUM VALUE OF
2500 KG (5500 LBS) OR 3180 LITERS
(840.7 US GALLONS FOR A DENSITY = 0,785):
ON PANEL 5004VU:
(1)HIGH LEVEL/TANK1 AND TANK2 LIGHTS
COME ON.
(2)VALVE LH/RH OPEN LIGHTS ARE OFF.
- REFUELING VALVE ARE CLOSED.
C. ON FUEL TANKER INDICATOR:
- POINTER AT ZERO.
D. ON REFUELING PANEL 5004VU:
SWITCH IN OFF POSITION.
(2)PLACE REFUELING/REFUEL VALVE/LH AND
*** CONTINUED ***
AH
28-25-73
FUT 10000-001
2-400 PAGE
3
DEC 01/14
28-25-73

CLOSURE OF VALVES
FUT 10000-001
4
DEC14
RH SWITCHES IN NORM

POSITION.
005

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
006
________
CLOSE-UP
USED).
EQUIPMENT.
*****
AH
E N D
O F
T E X T
*****
28-25-73
FUT 10000-001
2-400 PAGE
4
DEC 01/14
28-25-73
5
AH
DEFUEL/REFUEL PANEL
FUT 10000-001
DEC14
28-25-73
FUT 10000-001
2-400
PAGE
5
DEC 01/14
28-25-73

CLOSURE OF VALVES
FUT 10000-002
1
DEC14
ZONING DATA
___________
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
_________
MAN-HOURS
PUBLICATION
___________
JIC
JIC

(DISPLAY UNITS
EXPLORATION)
SUPPLY
AH
31-63-00-PRO-10000
24-46-00-EAD-10000
28-25-73
FUT 10000-002
2-400 PAGE
1
DEC 01/14
28-25-73

CLOSURE OF VALVES
001
FUT 10000-002
2
DEC14

___________________________________
EXPLORATION)
____________
_______________________
316300-PRO-10000
DISPLAY UNITS (DU).
002
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
*** CONTINUED ***

AH
28-25-73
FUT 10000-002
2-400 PAGE
2
DEC 01/14
28-25-73

CLOSURE OF VALVES
003
FUT 10000-002
3
DEC14

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
004
___________
PREPARATION
005
_____________________________________
FUNCTIONAL
REF. FIG. 282573-FUT-00120
1. CHECK CORRECT OPERATION OF HIGH LEVEL
SENSORS.
A. ON REFUELING CONTROL PANEL 100QU
SWITCH IN REFUEL POSITON.
(2)PLACEREFUELING/REFUEL VALVE/LH(RH)
SWITCHES IN OPEN POSITION
- REFUELING/VALVE OPEN/LH(RH) LIGHTS
COME ON.
- HIGH LEVEL/LH(RH) LIGHTS ARE OFF.
NOTE : IN THE OPPOSITE CASE PERFORM A
PARTIAL DEFUELING.
(AMM: 121128-DFG-10000).
B. REFUEL, BY TANK, ABOVE MAXIMUM VALUE OF
2500 KG (5500 LBS) OR 3180 LITERS
(840.7 US GALLONS FOR A DENSITY = 0,785):
ON REFUELING CONTROL PANEL 100QU
(1)HIGH LEVEL/LH (RH) LIGHTS COME ON.
(2)VALVE OPEN/LH(RH) LIGHTS ARE OFF.
*** CONTINUED ***
AH
28-25-73
FUT 10000-002
2-400 PAGE
3
DEC 01/14
28-25-73

CLOSURE OF VALVES
FUT 10000-002
4
DEC14
- REFUELING VALVE ARE CLOSED.

C. ON FUEL TANKER INDICATOR:
- POINTER AT ZERO.
D. ON REFUELING CONTROL PANEL 100QU
SWITCH IN OFF POSITION.
(2)PLACE REFUELING/REFUEL VALVE/LH(RH)
SWITCHES IN NORM POSITION.
006

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
007
________
CLOSE-UP
USED).
EQUIPMENT.
*****
AH
E N D
O F
T E X T
*****
28-25-73
FUT 10000-002
2-400 PAGE
4
DEC 01/14
28-25-73
5
AH
DEFUEL/REFUEL PANEL
FUT 10000-002
DEC14
28-25-73
FUT 10000-002
2-400
PAGE
5
DEC 01/14
28-25-73

RAI 10000-002
1
MAR12
ZONING DATA
___________
ZONE
: 523
623
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
_________
MAN-HOURS
ELAPSED TIME
SPARE
: 01 FUEL HIGH LEVEL SENSOR
282570-14-070
EXPENDABLE
: 02 WASHERS
02 SCREWS
282570-14-070
282570-14-050

OF NACA INTAKE
: FUNCTIONAL TEST OF HIGH
LEVEL SENSOR
28-12-71-RAI-10000
PUBLICATION
___________
JIC
JIC
AH
28-25-73-FUT-10000
28-25-73
RAI 10000-002
2-400 PAGE
1
MAR 01/12
28-25-73

001
RAI 10000-002
2
MAR12
_______
WARNING
WARNING C.D.C.C.L.
CONTROL LIMITATION
CONTROL LIMITATION.
CONFIGURATION.
002
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
*** CONTINUED ***
AH
28-25-73
RAI 10000-002
2-400 PAGE
2
MAR 01/12
28-25-73

RAI 10000-002
3
MAR12

003
____________________________
REMOVAL
OF THE NACA INTAKE
281271-RAI-10000.
004
_________________________________
REMOVAL
OF FUEL HIGH LEVEL SENSOR
REF. FIG. 282573-RAI-00100
2. REMOVE SCREWS (2) AND WASHERS (3)
3. REMOVE HIGH LEVEL SENSOR (1).
005
______________________________________
INSTALLATION
OF FUEL HIGH LEVEL SENSOR
REF. FIG. : 282573-RAI-00100
1. INSTALL HIGH LEVEL SENSOR (1) ON ITS SUPPORT
FASTEN IT BY MEANS OF SREWS (2) AND WASHERS
(3).
006
_________________________________
INSTALLATION
OF THE NACA INTAKE
281271-RAI-10000.
007
________
CLOSE-UP
*** CONTINUED ***
AH
28-25-73
RAI 10000-002
2-400 PAGE
3
MAR 01/12
28-25-73

RAI 10000-002
4
MAR12
6. REMOVE PLATFORM.
008
_____________________________________
FUNCTIONAL
282573-FUT-10000
*****
AH
E N D
O F
T E X T
*****
28-25-73
RAI 10000-002
2-400 PAGE
4
MAR 01/12
28-25-73
5
AH
HIGH LEVEL SENSOR
RAI 10000-002
MAR12
28-25-73
RAI 10000-002
2-400
PAGE
5
MAR 01/12
28-25-74

OF OVERWING REFUELING
CAP FOR CORROSION CHECK
RAI 10000-003
1
DEC14
ZONING DATA
___________
ZONE
ACCESS
: 520
523
620
623
: 523GT
623GT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
: 01 PLATFORM 3 M (10 FT)
EXPENDABLE
: 04 SEAL
BULK MATERIAL : SEALANT

DINITROL AV15
DINITROL AV30
_________
MAN-HOURS
28-25-74
09-019
05-027
05-027
PUBLICATION
___________
JIC

AH
57-00-00-OAC-10000
28-25-74
RAI 10000-003
2-400 PAGE
1
DEC 01/14
28-25-74

001
RAI 10000-003
2
DEC14
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
2. INSTALL PLATFORM, TO GAIN ACCESS TO TOP
SKIN.
003
_______________________________
OPENING
570000-OAC-10000
*** CONTINUED ***
AH
28-25-74
RAI 10000-003
2-400 PAGE
2
DEC 01/14
28-25-74

RAI 10000-003
3
DEC14

004
______________________
REMOVAL
OF CAP SNAP ON
REF.FIG.:282574-RAI-00100
1. REMOVE THE FUEL CAP(2) LOCATED ON WING UPPER
SURFACE:
- BY MEANS OF SCREWDRIVER LOOSE THE
SCREW (1) (4/5 TURNS)
- PRESS AND UNSCREW THE CAP (2) A QUARTER
OF TURN,THEN RELEASE IT.
005
_____
CHECK
REF.FIG. 282574-RAI-00100
1. REMOVE THE SCREW (1) FROM FUEL TANK CAP (2)
2. VISUALLY CHECK THE SCREW (1) AND THE CAP (2)
FOR ABSENCE OF CORROSION.
3. BY MEANS OF A PAINTBRUSH AND FUEL AS SOLVENT
CLEAN THE SCREW (1) AND THE CAP (2).
4. BE CAREFUL TO CLEAN REFUELLING FILTER (4)
THE WING ORIFICE COLLAR AND THE REFUELLING
PANEL.
5. CHECK THE PARTS FOR ABSENCE OF CORROSION.
IF ANY DAMAGED IS DETECTED PERFORM FOLLOWING
OPERATION:
A. REMOVE SCREW (6) AND FLANGE (7)
B. REMOVE AND DISCARD SEAL (5)
- FOR INDEEP INVESTIGATION REFER TO ATR MANUAL
CPCICF CHAPT.2 GENERALITY AND
*** CONTINUED ***
AH
28-25-74
RAI 10000-003
2-400 PAGE
3
DEC 01/14
28-25-74

RAI 10000-003
4
DEC14
CHAPT.28-25-00 FUEL SYSTEM-GRAVITY

REFUELLING CAP.
- FILL THE DATA FORM 2.7 THEN RETURN IT TO ATR
6. INSTALL NEW SEAL (5)
7. INSTALL FLANGE (7) AND SCREW (6)
8. SEAL WITH MAT.09-019C BETWEEN THE FLANGE
EDGE (7) AND THE REFUELLING PANEL
006
___________________________
INSTALLATION
OF CAP SNAP ON
REF.FIG. 282574-RAI-00100
1. LUBRICATE THE SCREW (1) BY CLEAN FUEL AND
REINSTALL IT ON FUEL CAP (2).
2. INSTALL THE NEW SEAL (3)
3. INSTALL THE FUEL CAP (2) BY PRESSING AND
TURNING IT A QUARTER OF TURN.
4. BY MEANS OF A SCREWDRIVER,TIGHTEN THE SCREW
(1) (4/5 TURNS) TO LOCK THE CAP (2).
NOTE: THE CAP MUST BE FLUSH WITH THE WING
UPPER SURFACE.
5. APPLY A SEALBEAD OF PR (09-019) BETWEEN THE
EDGE OF FUEL TANK ACCESS AND THE EDGE OF
REFUELLING PANEL (5).
WAIT UNTIL THE PR IS TACK FREE, THEN APPLY
DINITROL AV15 (05-027P) OR AV30 (05-027N)
ON THE ENTIRE SURFACE OF THE FUEL TANK
CAP (2) AND THE REFUELLING PANEL (5).
*** CONTINUED ***

AH
28-25-74
RAI 10000-003
2-400 PAGE
4
DEC 01/14
28-25-74

007
RAI 10000-003
5
DEC14
_______________________________
CLOSING
570000-OAC-10000
008
________
CLOSE-UP
6. REMOVE PLATFORM.
*****
AH
E N D
O F
T E X T
*****
28-25-74
RAI 10000-003
2-400 PAGE
5
DEC 01/14
28-25-74
6
AH
OVERWING REFUELING
FILTER
RAI 10000-003
DEC14
28-25-74
RAI 10000-003
2-400
PAGE
6
DEC 01/14
28-41-71

OF TANK FUEL TEMPERATURE
SENSOR
RAI 10000-002
1
DEC14
ZONING DATA
___________
ZONE
ACCESS
: 210
531
: 531AB
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
MECHANIC
ELECTRIC
___
MEN
_________
MAN-HOURS
01
01
ELAPSED TIME
GSE

01 WING ACCESS PLATFORM
01 THERMOMETER
SPARE
: 01 FUEL TEMPERATURE SENSOR
284170
EXPENDABLE
: 01 SEAL
284170

LOWER SURFACE TRAILING
EDGES
: REFUELING
57-54-20-OAC-10000
PUBLICATION
___________
JIC
JIC
AH
12-11-00-FLG-10020
28-41-71
RAI 10000-002
2-400 PAGE
1
DEC 01/14
28-41-71

SENSOR
001
RAI 10000-002
2
DEC14
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
1. MAKE CERTAIN THAT LEFT TANK IS DEFUELLED
(DEFUEL IF NECESSARY, REF. JIC 121100-DFG10000).
3. POSITION ACCESS PLATFORM 3 M (10 FT) TO
GAIN ACCESS TO WING LOWER SURFACE.
*** CONTINUED ***

AH
28-41-71
RAI 10000-002
2-400 PAGE
2
DEC 01/14
28-41-71

SENSOR
003
RAI 10000-002
3
DEC14
_______________________________________
OPENING
OF LOWER SURFACE TRAILING EDGES
JIC : 575420-OAC-10000
OPEN TRAILING EDGES MENTIONED IN ACCESS
SECTION OF JOB CARD PAGE 1.
004
DE-ENERGIZATION OF FUEL TEMPERATURE

___________________________________
ELECTRICAL CIRCUIT
__________________
1. ON PANEL 120VU, OPEN, SAFETY AND TAG
CIRCUIT BREAKER
2QL
FUEL/TEMP/TANK/IND
2. ON PANEL 121VU, OPEN, SAFETY AND TAG
CIRCUIT BREAKER
2QE
FUEL/FUEL FEED/X FEED
005
__________________________________
REMOVAL
OF FUEL TEMPERATURE SENSOR
REF. FIG. 284171-RAI-00100
1. DISCONNECT CONNECTOR (1).
2. INSTALL BLANKING CAPS ON CONNECTORS (1) AND
(2).
3. UNSAFETY SENSOR (3), UNSCREW AND REMOVE.
5. BLANK BARED ORIFICE ON FEEDER TANK.
006
_______________________________________
INSTALLATION
OF FUEL TEMPERATURE SENSOR
1. REMOVE BLANKING PLUG INSTALLED ON FEEDER
TANK ORIFICE.
2. CHECK THAT AREA IS CLEAN.
*** CONTINUED ***
AH
28-41-71
RAI 10000-002
2-400 PAGE
3
DEC 01/14
28-41-71

SENSOR
RAI 10000-002
4
DEC14
3. REMOVE BLANKING CAPS INSTALLED ON CONNECTORS

(1) AND (2).
4. CHECK CONDITION OF PINS.
5. POSITION A NEW SEAL (4) ON SENSOR (3).
(SEAL MUST BE PREVIOUSLY LUBRICATED WITH
CLEAN FUEL).
6. POSITION SENSOR (3) EQUIPPED WITH SEAL (4).
SCREW IN AND TIGHTEN SENSOR (3).
TORQUE TO 4-6 NM (35.5-53 LBS/INCH)
7. WIRELOCK SENSOR (3).
8. CONNECT CONNECTORS (1) AND (2).
007
ENERGIZATION OF FUEL TEMPERATURE ELECTRICAL

___________________________________________
CIRCUIT
_______
1. ON PANEL 120VU, REMOVE SAFETY CLIP AND TAG
AND CLOSE CIRCUIT BREAKER 2QL.
2. ON PANEL 121VU, REMOVE SAFETY CLIP AND TAG
AND CLOSE CIRCUIT BREAKER 2QE.
008
_________
REFUELING
121100-FLG-10020
009
CHECK OF FUEL TEMP INDICATION PART 1/2

_______________________________________
(CLEANING/DRYING OF FUEL TEMP PROBE AREA)
_________________________________________
1. CLEAN TEMPERATURE SENSOR ATTACHMENT AREA
USING A CLEAN CLOTH.
2. CHECK FOR ABSENCE OF LEAKAGE OR SEEPING AT
FUEL TEMPERATURE SENSOR-TO-REAR SPAR
JUNCTION.
*** CONTINUED ***
AH
28-41-71
RAI 10000-002
2-400 PAGE
4
DEC 01/14
28-41-71

SENSOR
RAI 10000-002
5
DEC14

EQUIPMENT.
010

_______________________________________
(INDICATION CHECK)
__________________
1. OPEN THE OVERWING REFUELING CAP.
2. BY MEANS A THERMOMETER, MEASURE AND NOTE THE
FUEL TEMPERATURE.
3. CLOSE THE OVERWING REFUELING CAP.
4. ON PANEL 120VU, CLOSE CIRCUIT BREAKER:
2QL
5. CHECK ON FUEL TEMPERATURE INDICATOR (PANEL
25VU) THAT INDICATED VALUE IS IN ACCORDANCE
WITH THE ONE RECORDED IN THE THERMOMETER
011
_______________________________________
CLOSING
JIC : 575420-OAC-10000
CLOSE TRAILING EDGES PREVIOUSLY OPENED.
012
________
CLOSE-UP
2. REMOVE NO SMOKING NOTICES.
*****
AH
E N D
O F
T E X T
*****
28-41-71
RAI 10000-002
2-400 PAGE
5
DEC 01/14
28-41-71
6
AH
FUEL TEMPERATURE SENSOR
RAI 10000-002
DEC14
28-41-71
RAI 10000-002
2-400
PAGE
6
DEC 01/14
28-41-71
7
AH

EDGE
RAI 10000-002
DEC14
28-41-71
RAI 10000-002
2-400
PAGE
7
DEC 01/14
28-41-81

OF FUEL TEMPERATURE
INDICATOR
RAI 10000-001
1
DEC14
ZONING DATA
___________
ZONE
: 210
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
: 01 WING ACCESS PLATFORM

01 THERMOMETER
_________
MAN-HOURS
PUBLICATION
___________
JIC

SUPPLY
AH
24-40-00-EAD-10000
28-41-81
RAI 10000-001
2-400 PAGE
1
DEC 01/14
28-41-81

OF FUEL TEMPERATURE
INDICATOR
001
RAI 10000-001
2
DEC14
___________
PREPARATION
1. ON PANEL 120VU, OPEN, SAFETY AND TAG CIRCUIT
BREAKER
2QL
FUEL/TK TEMP IND
2. ON PANEL 25VU,
REMOVE FUEL TEMPERATURE INDICATOR (1QL) BY
USING BELOW PROCEDURE:
002
STANDARD REMOVAL OF FLIGHT COMPARTMENT

______________________________________
EQUIPMENT
_________
NOTE:THE SHAPE OF LOCKING COLLARS,THE QUANTITY
OF BINDING SCREWS AS WELL AS THE SHAPE
AND QUANTITY OF CONNECTORS MAY BE DIFFERENT
ACCORDING THE EQUIPMENT.
NEVERTHELESS,THE REMOVAL AND INSTALLATION
PROCEDURE IS IDENTICAL.
REF. FIG. 310000-RAI-00101
CAUTION: DO NOT LOOSEN LOCKING COLLAR
ATTACHMENT SCREWS.
1. REMOVE CABIN PANEL VU (1).
2. SUFFICIENTLY LOOSEN BINDING SCREWS (6) OF
EQUIPMENT LOCKING COLLAR (2) ON CABIN PANEL
VU (1).(DO NOT COMPLETELY UNSCREW).
3. PULL EQUIPMENT (4) ALONG ITS LOCKING COLLAR
(2).
4. DISCONNECT CONNECTORS(3) FROM RECEPTACLE (5)
5. REMOVE EQUIPMENT (4).
6. INSTALL PROTECTIVE CAP ON EACH CONNECTOR (3)
AND ON EACH RECEPTACLE (5).
*** CONTINUED ***
AH
28-41-81
RAI 10000-001
2-400 PAGE
2
DEC 01/14
28-41-81

OF FUEL TEMPERATURE
INDICATOR
003
RAI 10000-001
3
DEC14
STANDARD INSTALLATION OF FLIGHT COMPARTMENT

___________________________________________
EQUIPMENT
_________
REF. FIG. 310000-RAI-00101
1. CLEAN AND INSPECT INSTRUMENT CABIN PANEL VU
(1) AND EQUIPMENT (4) INTERFACE AREA.
2. REMOVE PROTECTIVE CAPS INSTALLED ON CONNECTORS (3) AND RECEPTACLES (5).
3. MAKE CERTAIN THAT PINS ARE IN CORRECT CONDITION AND CONNECT CONNECTORS (3) WITH RECEPTACLES (5).
4. INSTALL EQUIPMENT (4) BY SLIDING IT ALONG
ITS LOCKING COLLAR (2).
5. POSITION EQUIPMENT AND TIGHTEN LOCKING COLLAR (2) BINBING SCREWS (6).
6. INSTALL CABIN VU PANEL (1).
004
___________________________________________
ENERGIZATION
244000-EAD-10000
005

_______________________________________
(INDICATION CHECK)
__________________
2. BY MEANS A THERMOMETER, MEASURE AND NOTE THE
FUEL TEMPERATURE.
4. ON PANEL 120VU, CLOSE CIRCUIT BREAKER:
2QL
*** CONTINUED ***
AH
28-41-81
RAI 10000-001
2-400 PAGE
3
DEC 01/14
28-41-81

OF FUEL TEMPERATURE
INDICATOR
RAI 10000-001
4
DEC14
5. CHECK ON FUEL TEMPERATURE INDICATOR (PANEL

25VU) THAT INDICATED VALUE IS IN ACCORDANCE
WITH THE ONE RECORDED IN THE THERMOMETER
006
______________________________________________
DE-ENERGIZATION
244000-EAD-10000
*****
AH
E N D
O F
T E X T
*****
28-41-81
RAI 10000-001
2-400 PAGE
4
DEC 01/14
28-41-81
5
AH
FLIGHT COMPARTMENT
EQUIPMENT
RAI 10000-001
DEC14
28-41-81
RAI 10000-001
2-400
PAGE
5
DEC 01/14
28-42-00

QUANTITY INDICATION
FUT 10000-002
1
DEC14
ZONING DATA
___________
ZONE
ACCESS
: 190
210
: 192JR
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
_________
MAN-HOURS
PUBLICATION
___________
JIC
JIC
JIC
SUPPLY
: DEFUELING
: REFUELING
AH
24-46-00-EAD-10000
12-11-00-DFG-10000
12-11-00-FLG-10020
28-42-00
FUT 10000-002
2-400 PAGE
1
DEC 01/14
28-42-00

QUANTITY INDICATION
001
FUT 10000-002
2
DEC14
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
003
___________
PREPARATION
*** CONTINUED ***

AH
28-42-00
FUT 10000-002
2-400 PAGE
2
DEC 01/14

QUANTITY INDICATION
004
28-42-00
FUT 10000-002
3
DEC14
_________
DEFUELING
121100-DFG-10000
005

_______________________
QUANTITY INDICATOR
__________________
REF. FIG. 282573-FUT-00120
1. ON PANEL 121VU
. CHECK THAT THE FOLLOWING CIRCUIT BREAKERS
ARE CLOSED :
- 1QT (2QT) FUEL/FQI L R TANK
- 2QU FUEL/FUELLING CTL & IND
2. ON REFUELING PANEL 5004VU
A. PLACE REFUEL/OFF/DEFUEL SWITCH (4QU) IN
POSITION :
- REFUEL.
B. PLACE REFUEL VALVES/LH (RH) SWITCH 5QU
(6QU) IN POSITION :
- NORM (REFUEL/DEFUEL VALVES OPEN)
C. WHEN FUEL PRESSURE FROM TANKER IS NORMAL
(3.5 BARS), THE VALVE/LH (RH)/OPEN
OF ACTUATING INDICATOR LIGHT, COMES ON.
FULL TANK TO 2500 KG (5500 LBS).
CHECK OF THIS SAME VALUE IS DISPLAYED :
.ON FUEL QUANTITY INDICATOR LEFT(RIGHT)
ON PANEL 4VU.
.ON FUEL REPEATER INDICATOR LEFT(RIGHT)
(IF IT IS PROVIDE) ON PANEL 5004VU.
D. ON PANEL 5004VU :
- PLACE REFUEL VALVES/LH(RH) SWITCH IN
SHUT POSITION. SHUT DOWN PRESSURE
FROM TANKER.
*** CONTINUED ***
AH
28-42-00
FUT 10000-002
2-400 PAGE
3
DEC 01/14
28-42-00

QUANTITY INDICATION
FUT 10000-002
4
DEC14
3. EXECUTE THE SAME CHECK (2.) ON THE OTHER

TANK.
WHEN THE BOTH INDICATORS ARE CHECKED, PLACE
REFUEL/OFF/DEFUEL SWITCH ON OFF POSITION
- VALVE/LH(RH)/OPEN INDICATOR LIGHTS GO
OFF.
- PLACE REFUEL VALVES/LH(RH) SWITCHES IN
NORM POSITION.
006
_________
REFUELING
121100-FLG-10020
007

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
008
________
CLOSE-UP
USED).
EQUIPMENT.
*****
AH
E N D
O F
T E X T
*****
28-42-00
FUT 10000-002
2-400 PAGE
4
DEC 01/14
28-42-00
5
AH
DEFUEL/REFUEL PANEL
FUT 10000-002
DEC14
28-42-00
FUT 10000-002
2-400
PAGE
5
DEC 01/14
28-42-00

QUANTITY INDICATION
FUT 10000-003
1
DEC14
ZONING DATA
___________
ZONE
ACCESS
: 190
210
: 192JR
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
_________
MAN-HOURS
PUBLICATION
___________
JIC
JIC
JIC
JIC

(DISPLAY UNITS
EXPLORATION)
SUPPLY
: DEFUELING
: REFUELING
AH
31-63-00-PRO-10000
24-46-00-EAD-10000
12-11-00-DFG-10000
12-11-00-FLG-10020
28-42-00
FUT 10000-003
2-400 PAGE
1
DEC 01/14
28-42-00

QUANTITY INDICATION
001
FUT 10000-003
2
DEC14

___________________________________
EXPLORATION)
____________
_______________________
316300-PRO-10000
DISPLAY UNITS (DU).
002
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
*** CONTINUED ***

AH
28-42-00
FUT 10000-003
2-400 PAGE
2
DEC 01/14
28-42-00

QUANTITY INDICATION
003
FUT 10000-003
3
DEC14

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
004
___________
PREPARATION
005
_________
DEFUELING
121100-DFG-10000
006

_______________________
QUANTITY INDICATION
___________________
REF. FIG. 282573-FUT-00120
1. ON PANEL 121VU
. CHECK THAT THE FOLLOWING CIRCUIT BREAKERS
ARE CLOSED :
- 1QT (2QT) FUEL/FCU CHAN 1(2)
- 2QU FUEL/FUELLING CTL & IND
2. ON REFUELING CONTROL PANEL 100QU
A. PLACE REFUEL/OFF/DEFUEL SWITCH IN
REFUEL POSITION.
B. PLACE REFUEL VALVES/LH (RH) SWITCH IN
NORM POSITION (REFUEL/DEFUEL VALVES
OPEN).
C. WHEN FUEL PRESSURE FROM TANKER IS NORMAL
(3.5 BARS), THE VALVE/OPEN/LH (RH)
*** CONTINUED ***
AH
28-42-00
FUT 10000-003
2-400 PAGE
3
DEC 01/14

QUANTITY INDICATION
28-42-00
FUT 10000-003
4
DEC14
OF ACTUATING INDICATOR LIGHT, COMES ON.

FULL TANK TO 2500 KG (5500 LBS).
CHECK OF THIS SAME VALUE IS DISPLAYED :
.ON MFD UPPER WINDOW, IN ENGINE SD PAGE
.ON FUEL REPEATER INDICATOR LEFT(RIGHT)
(IF IT IS PROVIDE) ON REFUELING CONTROL
PANEL 100QU.
D. ON REFUELING CONTROL PANEL 100QU
- PLACE REFUEL VALVES/LH(RH) SWITCH IN
SHUT POSITION. SHUT DOWN PRESSURE
FROM TANKER.
3. EXECUTE THE SAME CHECK (2.) ON THE OTHER
TANK.
WHEN THE BOTH INDICATORS ARE CHECKED, PLACE
REFUEL/OFF/DEFUEL SWITCH ON OFF POSITION
- VALVE/LH(RH)/OPEN INDICATOR LIGHTS GO
OFF.
- PLACE REFUEL VALVES/LH(RH) SWITCHES IN
NORM POSITION.
007
_________
REFUELING
121100-FLG-10020
008

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
009
________
CLOSE-UP
*** CONTINUED ***
AH
28-42-00
FUT 10000-003
2-400 PAGE
4
DEC 01/14
28-42-00

QUANTITY INDICATION
FUT 10000-003
5
DEC14

USED).
EQUIPMENT.
*****
AH
E N D
O F
T E X T
*****
28-42-00
FUT 10000-003
2-400 PAGE
5
DEC 01/14
28-42-00
6
AH
DEFUEL/REFUEL PANEL
FUT 10000-003
DEC14
28-42-00
FUT 10000-003
2-400
PAGE
6
DEC 01/14
28-42-00

QUANTITY INDICATION WITH
SET PSD40-1 OR SIMILAR
FUT 10010-002
1
DEC14
ZONING DATA
___________
ZONE
: 210
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
GSE
: 01
01
01
01
___
MEN
CAPACITANCE METER
FUEL QTY PROBE TEST SET
INTERFACE CABLE
INTERFACE CABLE
_________
MAN-HOURS
PSD40-1
PSD40-555-1
PSD40-555-2
PUBLICATION
___________
JIC

OF FUEL QTY INDICATOR
AH
28-42-81-RAI-10000
28-42-00
FUT 10010-002
2-400 PAGE
1
DEC 01/14
28-42-00

001
FUT 10010-002
2
DEC14
___________
PREPARATION
FOLLOWING CIRCUIT BREAKERS :
1QT FUEL/FQI/L TANK
2QT FUEL/FQI/R TANK
3. POSITION CAPACITANCE METER AND INTERFACE
SET IN THE CABIN.
002
__________________________________
REMOVAL
OF FUEL QUANTITY INDICATOR
284281-RAI-10000
003
FUNCTIONAL TEST OF FUEL QUANTITY INDICATOR

__________________________________________
PART 1/2
________
(LEFT TANK AND RIGHT TANK CAPACITANCES)
_______________________________________
REF. FIG. 284272-FUT-00100
1. REMOVE PROTECTIVE CAPS INSTALLED ON
CONNECTORS (2)(3)(7)(8) AND RECEPTACLE (5).
2.TOTAL CAPACITANCE MEASUREMENT (LEFT TANK):
A. CONNECT THE COAXIAL CABLE (8) AND THE
MULTIPIN PLUG (3) ON SET TEST
BY USING CABLE 555-1.
B. PERFORM THE MEASUREMENT OF THE
CAPACITANCE AND RECORD THE VALUE.
LH TANK TOTAL CAPACITANCE = _______PF
C. DISCONNECT THE COAXIAL CABLE AND THE
MULTIPIN PLUG FROM SET TEST.
3.TOTAL CAPACITANCE MEASUREMENT (RIGHT TANK):
MULTIPIN PLUG (2) ON SET TEST
BY USING CABLE 555-2.
*** CONTINUED ***
AH
28-42-00
FUT 10010-002
2-400 PAGE
2
DEC 01/14
28-42-00

FUT 10010-002
3
DEC14

RH TANK TOTAL CAPACITANCE = _______PF
004
_______________________________________
INSTALLATION
284281-RAI-10000
005
FUNCTIONAL TEST OF FUEL QUANTITY INDICATOR

__________________________________________
PART 2/2
________
(CHECK FUEL QUANTITIES)
_______________________
1. ON PANEL 121VU, CLOSE CIRCUIT BREAKERS 1QT
AND 2QT.
REF.FIG. 284200-FUT-00110(CORRESPONDANCE CHART)
REF.FIG. 284272-FUT-00100
2. BY MEANS OF CORRESPONDANCE CHART,
DETERMINE LH AND RH FUEL QUANTITIES
CORRESPONDING TO TOTAL CAPACITANCES
PREVIOUSLY RECORDED :
LH CORRESPONDING QUANTITY = _________KG.
RH CORRESPONDING QUANTITY = _________KG.
3. RECORD THE FUEL QUANTITY DISPLAYED ON FUEL
QUANTITY INDICATOR, ON LEFT HAND AND RIGHT
HAND SIDES.
4. CHECK THAT FUEL QUANTITIES READ ON
INDICATOR ARE VERY CLOSE TO
CORRESPONDING QUANTITIES DETERMINED
JUST PREVIOUSLY.
NOTE: ADMISSIBLE TOLERANCE: APPROX. +/- 50KG
5. MEASURE THE FUEL QUANTITY, CONTAINED INTO
EACH TANK, USING THE DRIPSTRICKS.
6. CHECK THAT BOTH VALUES:
*** CONTINUED ***
AH
28-42-00
FUT 10010-002
2-400 PAGE
3
DEC 01/14
28-42-00

FUT 10010-002
4
DEC14
- READ ON INDICATOR
- DETERMINED ACCORDING TO CAPACITIES
ARE CLOSE TO FUEL QUANTITY ESTIMATED
BY DRIPSTRICK.
NOTE: TOLERANCE: +/- 200 KG FOR EACH SIDE.
*****
AH
E N D
O F
T E X T
*****
28-42-00
FUT 10010-002
2-400 PAGE
4
DEC 01/14
28-42-00
5
AH
FUEL QUANTITY
INDICATING
FUT 10010-002
DEC14
28-42-00
FUT 10010-002
2-400
PAGE
5
DEC 01/14
28-42-00
6
AH
CHART OF KG/PF
CORRESPONDENCE
FUT 10010-002
DEC14
28-42-00
FUT 10010-002
2-400
PAGE
6
DEC 01/14
28-42-00

FUT 10010-003
1
DEC14
ZONING DATA
___________
ZONE
: 210
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
GSE
: 01
01
01
01
AH
___
MEN
CAPACITANCE METER
INTERFACE CABLE
ADAPTOR
_________
MAN-HOURS
PSD40-1
PSD40-555-1
98S28005002-000
28-42-00
FUT 10010-003
2-400 PAGE
1
DEC 01/14
28-42-00

001
FUT 10010-003
2
DEC14
___________
PREPARATION
2. ON PANEL 121VU,
A. OPEN THE FOLLOWING CIRCUIT BREAKERS:
1QT FUEL/FCU CHAN 1
2QT FUEL/FCU CHAN 2
3. PROVIDE CAPACITANCE METER AND INTERFACE SET.
4. BEFORE UNDERTAKING MAINTENANCE WORK ON THE
AIRCRAFT, DISPLAY WARNING NOTICES
PROHIBITING OPERATION ON THE LANDING GEAR.
002
FUNCTIONAL TEST OF FUEL CONTROL UNIT

____________________________________
PART 1/2
________
(LEFT TANK AND RIGHT TANK CAPACITANCES)
_______________________________________
REF. FIG. 284272-FUT-00100
1. OPEN THE NLG DOORS 713/714 AND THE FORWARD
AVIONNIC DOOR 811.
2. DISCONNECT CONNECTORS B1 AND B2 FROM FCU
PLUGS B1 AND B2.
3. TOTAL CAPACITANCE MEASUREMENT (LEFT TANK):
A. CONNECT THE CONNECTOR B1 TO THE
CAPACITANCE METER BY USING ADAPTOR
98S28005002-000 AND CABLE 555-1.
LH TANK TOTAL CAPACITANCE = _______PF
C. DISCONNECT CABLE 555-1 AND ADAPTOR
98S28005002-000 FROM CONNECTOR B1.
4. TOTAL CAPACITANCE MEASUREMENT (RIGHT TANK):
*** CONTINUED ***
AH
28-42-00
FUT 10010-003
2-400 PAGE
2
DEC 01/14
28-42-00

FUT 10010-003
3
DEC14
A. CONNECT THE CONNECTOR B2 TO THE

CAPACITANCE METER BY USING ADAPTOR
98S28005002-000 AND CABLE 555-1.
RH TANK TOTAL CAPACITANCE = _______PF
5. RECONNECT CONNECTORS B1 AND B2 ON FCU PLUGS
6. INSTALL THE FORWARD AVIONIC COMPARTMENT
DOOR AND CHECK THAT THE SEAL DOOR IS
CORRECTLY PLACED.
7. CLOSE THE NOSE LANDING GEAR DOORS 713/714.
003
FUNCTIONAL TEST OF FUEL CONTROL UNIT

____________________________________
PART 2/2
________
(CHECK FUEL QUANTITIES)
_______________________
1. ON PANEL 121VU, CLOSE CIRCUIT BREAKERS 1QT,
2QT AND 2QU.
REF.FIG. 284200-FUT-00110(CORRESPONDANCE CHART)
REF.FIG. 284272-FUT-00100
2. BY MEANS OF CORRESPONDANCE CHART,
DETERMINE LH AND RH FUEL QUANTITIES
CORRESPONDING TO TOTAL CAPACITANCES
PREVIOUSLY RECORDED :
LH CORRESPONDING QUANTITY = _________KG.
RH CORRESPONDING QUANTITY = _________KG.
3. RECORD THE FUEL QUANTITY DISPLAYED ON MFD
UPPER WINDOW, ENGINE SD PAGE FOR
LEFT HAND AND RIGHT HAND SIDES.
4. CHECK THAT FUEL QUANTITIES READ ON
DISPLAY ARE VERY CLOSE TO
CORRESPONDING QUANTITIES DETERMINED
JUST PREVIOUSLY.
*** CONTINUED ***
AH
28-42-00
FUT 10010-003
2-400 PAGE
3
DEC 01/14
28-42-00

FUT 10010-003
4
DEC14
NOTE: ADMISSIBLE TOLERANCE: APPROX. +/- 50KG

5.MEASURE THE FUEL QUANTITY, CONTAINED INTO
EACH TANK, USING THE DRIPSTRICKS.
6.CHECK THAT BOTH VALUES:
- READ ON DISPLAY
- DETERMINED ACCORDING TO CAPACITIES
ARE CLOSE TO FUEL QUANTITY ESTIMATED BY
DRIPSTRICK.
NOTE: TOLERANCE: +/- 200 KG FOR EACH SIDE.
*****
AH
E N D
O F
T E X T
*****
28-42-00
FUT 10010-003
2-400 PAGE
4
DEC 01/14
28-42-00
5
AH
FUEL QUANTITY
INDICATING
FUT 10010-003
DEC14
28-42-00
FUT 10010-003
2-400
PAGE
5
DEC 01/14
28-42-00
6
AH
CHART OF KG/PF
CORRESPONDENCE
FUT 10010-003
DEC14
28-42-00
FUT 10010-003
2-400
PAGE
6
DEC 01/14
28-42-00

QUANTITY INDICATION IN
LOW LEVEL RANGE
FUT 10020-001
1
DEC14
ZONING DATA
___________
ZONE
: 500
600
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
_________
MAN-HOURS
ELAPSED TIME
GSE
: 01 WATER DRAIN PURGING TOOL
98S12003000000
EXPENDABLE
: 01 O-RING
05 SCREW
284270
284270
: JACKING FOR A/C

: QUICK LEVELLING
SUPPLY
: DEFUELING
FUEL QUANTITY PROBE
07-11-00-JUP-10000
PUBLICATION
___________
JIC
JIC
JIC
JIC
JIC
AH
08-21-00-PRO-10000
24-46-00-EAD-10000
12-11-00-DFG-10000
28-42-72-RAI-10000
28-42-00
FUT 10020-001
2-400 PAGE
1
DEC 01/14
28-42-00

LOW LEVEL RANGE
001
FUT 10020-001
2
DEC14
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________________
AIRCRAFT
JACKING UP
071100-JUP-10000
003
_______________
QUICK
LEVELLING
082100-PRO-10000
004

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
*** CONTINUED ***
AH
28-42-00
FUT 10020-001
2-400 PAGE
2
DEC 01/14
28-42-00

LOW LEVEL RANGE
005
FUT 10020-001
3
DEC14
_________
DEFUELING
121100-DFG-10000
006
___________________
ADDITIONAL
DRAINING
REF. FIG. 122428-DRN-00100
ON RIGHT AND LEFT TANKS
- AT EACH WATER DRAIN, DRAIN FUEL UNTIL FLOW
CEASES, USING TOOL 98S12003000000
- REMOVE FUEL QUANTITY PROBES WITHOUT
DISCONNECT THEM, AND LAY THEM ON THE WING
UPPER SURFACE WITH THE PROCEDURE HERE BELOW.
007
______________________________
REMOVAL
OF FUEL QUANTITY PROBE
284272-RAI-10000
008
__________________________________________
FUNCTIONAL
TEST OF FUEL QUANTITY INDICATOR
REF. FIG. 284200-FUT-00120
1. ON WING UPPER SURFACE,
A. WHEN FUEL QUANTITY PROBES ARE DRY (FUEL
TANK EMPTY),
- CHECK THAT COCKPIT FUEL QUANTITY
INDICATOR DISPLAY 0.
B. INSTAL FUEL QUANTITY PROBES PREVIOUSLY
REMOVED (REF. JIC. 284272-RAI-10000).
2. CALIBRATION
A. PERFORM A CALIBRATION FROM 0 TO 400 KG
OF FUEL PER TANK, BY UPLIFTING FUEL BY
*** CONTINUED ***
AH
28-42-00
FUT 10020-001
2-400 PAGE
3
DEC 01/14
28-42-00

LOW LEVEL RANGE
FUT 10020-001
4
DEC14
100 KG INCREMENTS, ALTERING LEFT AND

RIGHT TANK FUEL FILLING.
B. CHECK THAT AT EACH INCREMENT THE
DIFFERENCE (QTY INTRODUCED-QTY INDICATED)
REMAINS POSITIVE OR EQUAL TO 0.
___________________________________
LEFT TANK
RIGHT TANK
___________________________________________
QTY
QTY
QTY
INTRODUCEDINDICATED DELTAINDICATED DELTA
(A)
(B)
(A-B)
(B)
(A-B)
________________________________________
100 KG
________________________________________
200 KG
________________________________________
300 KG
________________________________________
400 KG
________________________________________
009

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
010
____________________________________
LOWERING
071100-JUP-10000
011
________
CLOSE-UP
REF.FIG. 284272-RAI-00100
1. ON PANEL 4VU, CHECK THAT FUEL QUANTITY
INDICATED ON }FQI} IS IN ACCORDANCE WITH THE
FUEL QUANTITY INTO TANKS.
*** CONTINUED ***
AH
28-42-00
FUT 10020-001
2-400 PAGE
4
DEC 01/14
28-42-00

LOW LEVEL RANGE
FUT 10020-001
5
DEC14

EQUIPMENT.
REMOVE ACCESS PLATFORM.
*****
AH
E N D
O F
T E X T
*****
28-42-00
FUT 10020-001
2-400 PAGE
5
DEC 01/14
28-42-00
6
AH
COCKPIT FUEL QUANTITY

INDICATOR
FUT 10020-001
DEC14
28-42-00
FUT 10020-001
2-400
PAGE
6
DEC 01/14
28-42-00
7
AH
DRAINAGE SYSTEM
FUT 10020-001
DEC14
28-42-00
FUT 10020-001
2-400
PAGE
7
DEC 01/14
28-42-00
8
AH
TYPICAL REM/INSTALLATION
OF FUEL QUANTITY OR FUEL
TEMP/QUANTITY PROBE
FUT 10020-001
DEC14
28-42-00
FUT 10020-001
2-400
PAGE
8
DEC 01/14
28-42-00

LOW LEVEL RANGE
FUT 10020-002
1
DEC14
ZONING DATA
___________
ZONE
: 500
600
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
_________
MAN-HOURS
ELAPSED TIME
GSE
: 01 WATER DRAIN PURGING TOOL
98S12003000000
EXPENDABLE
: 01 O-RING
05 SCREW
284270
284270

(DISPLAY UNITS
EXPLORATION)
: JACKING FOR A/C
: QUICK LEVELLING
SUPPLY
: DEFUELING
FUEL QUANTITY PROBE
31-63-00-PRO-10000
PUBLICATION
___________
JIC
JIC
JIC
JIC
JIC
JIC
AH
07-11-00-JUP-10000
08-21-00-PRO-10000
24-46-00-EAD-10000
12-11-00-DFG-10000
28-42-72-RAI-10000
28-42-00
FUT 10020-002
2-400 PAGE
1
DEC 01/14
28-42-00

LOW LEVEL RANGE
001
FUT 10020-002
2
DEC14

___________________________________
EXPLORATION)
____________
_______________________
316300-PRO-10000
DISPLAY UNITS (DU).
002
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
*** CONTINUED ***

AH
28-42-00
FUT 10020-002
2-400 PAGE
2
DEC 01/14
28-42-00

LOW LEVEL RANGE
003
FUT 10020-002
3
DEC14
___________________
AIRCRAFT
JACKING UP
071100-JUP-10000
004
_______________
QUICK
LEVELLING
082100-PRO-10000
005

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
006
_________
DEFUELING
121100-DFG-10000
007
___________________
ADDITIONAL
DRAINING
REF. FIG. 122428-DRN-00100
ON RIGHT AND LEFT TANKS
- AT EACH WATER DRAIN, DRAIN FUEL UNTIL FLOW
CEASES, USING TOOL 98S12003000000
- REMOVE FUEL QUANTITY PROBES WITHOUT
DISCONNECT THEM, AND LAY THEM ON THE WING
UPPER SURFACE WITH THE PROCEDURE HERE BELOW.
008
______________________________
REMOVAL
284272-RAI-10000
*** CONTINUED ***

AH
28-42-00
FUT 10020-002
2-400 PAGE
3
DEC 01/14

LOW LEVEL RANGE
009
28-42-00
FUT 10020-002
4
DEC14
___________________________________________
FUNCTIONAL
TEST OF FUEL QUANTITY INDICATION
REF. FIG. 284200-FUT-00120
1. ON WING UPPER SURFACE,
A. WHEN FUEL QUANTITY PROBES ARE DRY (FUEL
TANK EMPTY),
- CHECK THAT ON MFD UPPER WINDOW, IN
ENGINE SD PAGE, THE FUEL QUANTITY
INDICATION DISPLAY 0.
B. INSTAL FUEL QUANTITY PROBES PREVIOUSLY
REMOVED (REF. JIC. 284272-RAI-10000).
2. CALIBRATION
A. PERFORM A CALIBRATION FROM 0 TO 400 KG
(880 LBS ) OF FUEL PER TANK, BY UPLIFTING
FUEL BY 100 KG (220 LBS) INCREMENTS,
ALTERING LEFT AND RIGHT TANK FUEL
FILLING.
B. CHECK THAT AT EACH INCREMENT THE
DIFFERENCE (QTY INTRODUCED-QTY INDICATED)
___________________________________
LEFT TANK
RIGHT TANK
___________________________________________
QTY
QTY
QTY
INTRODUCEDINDICATED DELTAINDICATED DELTA
(A)
(B)
(A-B)
(B)
(A-B)
________________________________________
100 KG
(220 LBS)
________________________________________
200 KG
(440 LBS)
________________________________________
300 KG
(660 LBS)
*** CONTINUED ***

AH
28-42-00
FUT 10020-002
2-400 PAGE
4
DEC 01/14
28-42-00

LOW LEVEL RANGE
FUT 10020-002
5
DEC14
________________________________________
400 KG
(880 LBS)
________________________________________
010

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
011
____________________________________
LOWERING
071100-JUP-10000
012
________
CLOSE-UP
REF.FIG. 284272-RAI-00100
CHECK THAT FUEL QUANTITY INDICATED IS IN
ACCORDANCE WITH THE QUANTITY CONTENTS
INTO TANKS.
EQUIPMENT.
REMOVE ACCESS PLATFORM.
*****
AH
E N D
O F
T E X T
*****
28-42-00
FUT 10020-002
2-400 PAGE
5
DEC 01/14
28-42-00
6
AH
DRAINAGE SYSTEM
FUT 10020-002
DEC14
28-42-00
FUT 10020-002
2-400
PAGE
6
DEC 01/14
28-42-00
7
AH
TEMP/QUANTITY PROBE
FUT 10020-002
DEC14
28-42-00
FUT 10020-002
2-400
PAGE
7
DEC 01/14
28-42-00
TEST OF FUEL QUANTITY

INDICATOR
TST 10000-001
1
DEC14
ZONING DATA
___________
ZONE
ACCESS
: 192
210
: 192JR
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
___
MEN
_________
MAN-HOURS
PUBLICATION
___________
JIC
SUPPLY
AH
24-46-00-EAD-10000
28-42-00
TST 10000-001
2-400 PAGE
1
DEC 01/14
28-42-00

INDICATOR
001
TST 10000-001
2
DEC14

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
002
__________________________________________
DE-ENERGIZATION
1. ON PANEL 121VU
- 1 QT(2QT) FUEL/FQI/NORM PWR SUPPLY/L
(R) TANK.
- 2QU
FUEL/FUELLING/CTL & IND.
003
_______________________________
TEST
REF. FIG. 282573-FUT-00120
1. ON REFUELING PANEL 5004VU
A. PLACE
- REFUELING/REFUEL/OFF/DEFUEL SWITCH 4QU
IN OFF POSITION
- REFUELING/REFUEL VALVE/L(R) SWITCH 5QU
(6QU) IN SHUT POSITION.
B. PRESS REFUELING/FQI TEST PUSHBUTTON
SWITCH AND THEN RELEASE, NO DISPLAY.
2. ON PANEL 121VU,
A. CLOSE CIRCUIT BREAKERS 1QT (2QT).
B. ON PANEL 4VU, LEFT (RIGHT) FUEL QUANTITY
INDICATOR 3QT READS FUEL QUANTITY REMAINING IN TANK CONCERNED.
3. ON PANEL 121VU
A. OPEN CIRCUIT BREAKERS 1QT (2QT).
*** CONTINUED ***
AH
28-42-00
TST 10000-001
2-400 PAGE
2
DEC 01/14
28-42-00

INDICATOR
TST 10000-001
3
DEC14
B. ON PANEL 4VU, LEFT (RIGHT) FUEL QUANTITY

INDICATOR 3QT DOES NOT GIVE ANY READING.
4. ON PANEL 121VU.
A. CLOSE CIRCUIT BREAKERS 1QT (2QT) AND THEN
2QU.
B. ON PANEL 4VU, FUEL QUANTITY INDICATOR
3QT READS QUANTITY REMAINING.
5. ON REFUELING PANEL 5004VU :
A. PRESS AND HOLD REFUELING FQI TEST PUSHBUTTON SWITCH 4QT.
- ON PANEL 4VU, LEFT (RIGHT) FUEL QUANTITY INDICATOR 3QT READS 8888.
B. RELEASE REFUELING FQI TEST PUSHBUTTON
SWITCH 4QT
- ON PANEL 4VU LEFT (RIGHT) FUEL QUANTITY INDICATOR 3QT READS FUEL QUANTITY
REMAINING IN TANK CONCERNED.
C. PLACE REFUELING/REFUEL VALVE/L(R) TANK
SWITCH 5QU (6QU) IN NORM POSITION.
6. ON PANEL 4VU
A. PRESS AND HOLD FUEL
3QT TEST PUSHBUTTON
- LEFT (RIGHT) FUEL
3QT READS : 8888.
- LOW LEVEL LIGHT
QUANTITY INDICATOR
SWITCH
QUANTITY INDICATOR
L (R) COMES ON.
B. RELEASE FUEL QUANTITY INDICATOR 3QT TEST

PUSHBUTTON SWITCH
- LEFT (RIGHT) FUEL QUANTITY INDICATOR
3QT READS FUEL QUANTITY REMAINING IN
TANK CONCERNED.
-LOW LEVEL LIGHT L (R) GOES OFF.
*** CONTINUED ***
AH
28-42-00
TST 10000-001
2-400 PAGE
3
DEC 01/14
28-42-00

INDICATOR
TST 10000-001
4
DEC14
7. ON PANEL 121VU
A. OPEN CIRCUIT BREAKERS 1QT (2QT).
B. ON PANEL 4VU, FUEL QUANTITY INDICATOR 3QT
DOES NOT GIVE ANY READING.
004
_______________________________________
ENERGIZATION
1. ON PANEL 121VU
- 1QT, 2QT, 2QU.
005

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
*****
AH
E N D
O F
T E X T
*****
28-42-00
TST 10000-001
2-400 PAGE
4
DEC 01/14
28-42-00
5
AH
DEFUEL/REFUEL PANEL
TST 10000-001
DEC14
28-42-00
TST 10000-001
2-400
PAGE
5
DEC 01/14
28-42-72
DETAILED VISUAL
INSPECTION OF FUEL
QUANTITY PROBES
DVI 10000-001
1
MAR12
ZONING DATA
___________
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
___
MEN
_________
MAN-HOURS
PUBLICATION
___________
JIC
FUEL QUANTITY PROBE
AH
28-42-72-RAI-10000
28-42-72
DVI 10000-001
2-400 PAGE
1
MAR 01/12
28-42-72
DETAILED VISUAL
INSPECTION OF FUEL
QUANTITY PROBES
001
DVI 10000-001
2
MAR12
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
REMOVE FUEL QUANTITY PROBES WITHOUT DISCONNECT
ELECTRICAL CONNECTOR AND WITHOUT REMOVING
CLAMPS.
PAY ATTENTION TO ELECTRICAL HARNESS USING THE
PROCEDURE HERE BELOW.
003
______________________________
REMOVAL
284272-RAI-10000
*** CONTINUED ***

AH
28-42-72
DVI 10000-001
2-400 PAGE
2
MAR 01/12
28-42-72
DETAILED VISUAL
INSPECTION OF FUEL
QUANTITY PROBES
004
DVI 10000-001
3
MAR12

___________________________________________
PROBES
______
REF. FIG.: 284272-RAI-00100
CHECK THAT :
- WIRES ARE NOT BROKEN ESPECIALLY AT
CONNECTION.
- ELECTRICAL HARNESS AND CLAMP ARE CORRECTLY
FIXED ON PROBES.
- ELECTRICAL HARNESS DO NOT HAVE ANY SIGN
OF CHAFING.
- LOW LEVEL SENSOR AND THERMISTANCE SENSOR
ARE NOT DAMAGED(IF INSTALLED).
005
___________________________________
INSTALLATION
284272-RAI-10000
006
________
CLOSE-UP
6. REMOVE PLATFORM.
*****
AH
E N D
O F
T E X T
*****
28-42-72
DVI 10000-001
2-400 PAGE
3
MAR 01/12
28-42-72
4
AH
TEMP/QUANTITY PROBE
DVI 10000-001
MAR12
28-42-72
DVI 10000-001
2-400
PAGE
4
MAR 01/12
28-42-72

QUANTITY PROBE SYSTEM
FUT 10000-003
1
MAR15
ZONING DATA
___________
ZONE
: 210
522
622
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
: 01
01
01
01
01
01
EXPENDABLE
: 01 O-RING
05 SCREW
284270
284270

EDGES
OF FUEL QTY INDICATOR
57-54-20-OAC-10000
ACCESS PLATFORM 4M (13FT)

INTERFACE CABLE
INTERFACE CABLE
INTERFACE CABLE
INTERFACE CABLE
_________
MAN-HOURS
PSD60-2R
PSD40-556YYY
PSD40-556ZZZ
PSD40-555-1
PSD40-555-2
PUBLICATION
___________
JIC
JIC
AH
28-42-81-RAI-10000
28-42-72
FUT 10000-003
2-400 PAGE
1
MAR 01/15
28-42-72

001
FUT 10000-003
2
MAR15
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
CROSSCHECK OF FUEL QUANTITY INDICATION

______________________________________
PART (1/2)
__________
ON 4VU, ON FUEL QUANTITY INDICATOR:
1. RECORD CURRENT FUEL QUANTITY INDICATED
FOR LH TANK PRELIMINARY INDICATION:
________ KG.
FOR RH TANK PRELIMINARY INDICATION:
________ KG.
*** CONTINUED ***

AH
28-42-72
FUT 10000-003
2-400 PAGE
2
MAR 01/15
28-42-72

003
FUT 10000-003
3
MAR15
___________
PREPARATION
1QT FUEL/FQI/L TANK
2QT FUEL/FQI/R TANK
3. PROVIDE ACCESS PLATFORM 4M (13FT) FOR
4. PROVIDE FUEL QUANTITY TEST SET AND INTERFACE CABLES.
004
___________________________________________
OPENING
OF LOWER SURFACE WING TRAILING EDGE
575420-OAC-10000
005
REMOVAL OF PROBES FROM TANKS

____________________________
(WITHOUT DISCONNECTING)
_______________________
REF. FIG. 284272-RAI-00100
NOTE : CONNECT GROUND OF FUEL TEST SET TO
AIRPLANE STRUCTURE.
1. REMOVE AND DISCARD SCREWS (4) FROM FUEL
QUANTITY PROBES.
2. REMOVE AND DISCARD O-RING (3).
3. BY USING THE EXTRACT HOLES (6), REMOVE AND
PLACE PROBES ON WINGS WITHOUT DISCONNECTING
THEIR CONNECTOR.
NOTE : CHECK CONDITION OF EACH DISCONNECTED
PLUG CONNECTOR AND RECEPTACLE CONNECTOR
- DAMAGE OF PINS AND INSULATION
*** CONTINUED ***
AH
28-42-72
FUT 10000-003
2-400 PAGE
3
MAR 01/15
28-42-72

FUT 10000-003
4
MAR15
- OXIDATION
- CORRECT CONNECTION OF LOCKING SYSTEM.
- REMOVE, IF NECESSARY, THE ELECTRICAL
FUSE INSTALLED ON REAR SPAR CONNECTORS
006
__________________________________
FUNCTIONAL
TEST OF PROBES ON WINGS
REF. FIG. 284272-FUT-00120
1. DISCONNECT CONNECTOR 501VC (600VC) LOCATED
AT THE REAR OF WINGS AND CONNECT FUEL TEST
SET (PROBE 1: INTERFACE CABLE -556YYY)
- CHECK THAT PROBE (A) VALUE IS 8.5 +/0.8 PF, AND RECONNECT CONNECTOR.
SET (PROBE 2: INTERFACE CABLE -556ZZZ)
- CHECK THAT PROBE (B) VALUE IS 12.9 +/0.5 PF, AND RECONNECT CONNECTOR.
- CHECK THAT PROBE (C) VALUE IS 51.4 +/0.5 PF, AND RECONNECT CONNECTOR.
- CHECK THAT PROBE (D) VALUE IS 18.7 +/0.5 PF, AND RECONNECT CONNECTOR.
- CHECK THAT PROBE (E) VALUE IS 38.65 +/0.5 PF, AND RECONNECT CONNECTOR.
*** CONTINUED ***
AH
28-42-72
FUT 10000-003
2-400 PAGE
4
MAR 01/15
28-42-72

FUT 10000-003
5
MAR15
- CHECK THAT PROBE (F) VALUE IS 14.5 +/0.5 PF, AND RECONNECT CONNECTOR.
007
_______________________________________
CLOSING
575420-OAC-10000
008
__________________________________
REMOVAL
284281-RAI-10000
009
________________________
FUNCTIONAL
TEST IN CABIN
REF. FIG. 284272-FUT-00100
1. REMOVE PROTECTIVE CAPS INSTALLED ON
CONNECTORS (2)(3)(7)(8) AND RECEPTACLE (5).
2.TOTAL CAPACITANCE MEASUREMENT (LEFT TANK):
MULTIPIN PLUG (3) ON SET TEST BY USING
CABLE 555-1.
B. PERFORM THE MEASUREMENT OF TOTAL
SYSTEM CAPACITANCE:
NOTE: THE CAPACITANCE VALUE MUST BE INCLUDED
BETWEEN 143.2 PF AND 148 PF
3.TOTAL CAPACITANCE MEASUREMENT (RIGHT TANK):
MULTIPIN PLUG (2) ON SET TEST BY USING
CABLE 555-2.
B. PERFORM THE MEASUREMENT OF TOTAL
SYSTEM CAPACITANCE:
NOTE: THE CAPACITANCE VALUE MUST BE INCLUDED
BETWEEN 143.2 PF AND 148 PF
MULTIPIN PLUG OF THE FROM SET TEST.
*** CONTINUED ***
AH
28-42-72
FUT 10000-003
2-400 PAGE
5
MAR 01/15
28-42-72

010
FUT 10000-003
6
MAR15
_______________________________________
INSTALLATION
284281-RAI-10000
011
__________________________________
RE-INSTALLATION
OF PROBES ON TANKS
REF.FIG. 284272-RAI-00100
R
R
R
R
1. CHANGE THE O-RING, WHICH MUST BE PREVIOUSLY

LUBRICATED WITH CLEAN FUEL. INSTALL EACH
PROBE (TAKE CARE OF THE POSITIONING) INTO
ITS PLACE.

012
________
CLOSE-UP
1. REMOVE WARNING NOTICE.
2. ON PANEL 121VU, REMOVE SAFETY CLIPS AND TAGS
AND CLOSE CIRCUIT BREAKERS PREVIOUSLY
OPENED.
3. REMOVE ACCESS PLATFORM AND MAKE CERTAIN
THAT WORKING AREA IS CLEAN AND CLEAR OF
TOOLS AND MISCELLANEOUS ITEMS OF EQUIPMENT.
013
CROSSCHECK FUEL QUANTITY INDICATION

___________________________________
PART (2/2)
__________
ON 4VU, ON FUEL QUANTITY INDICATOR:
1. CHECK COHERENCE OF FUEL QUANTITY INDICATED
FOR LEFT TANK WITH INDICATION PREVIOUSLY
RECORDED BEFORE TEST IN CROSSCHECK
(PART 1/2).
FOR RIGHT TANK WITH INDICATION PREVIOUSLY
*** CONTINUED ***
AH
28-42-72
FUT 10000-003
2-400 PAGE
6
MAR 01/15
28-42-72

FUT 10000-003
7
MAR15

(PART 1/2).
*****
AH
E N D
O F
T E X T
*****
28-42-72
FUT 10000-003
2-400 PAGE
7
MAR 01/15
28-42-72
8
AH
TEMP/QUANTITY PROBE
FUT 10000-003
MAR15
28-42-72
FUT 10000-003
2-400
PAGE
8
MAR 01/15
28-42-72
9
AH
FUEL QUANTITY
INDICATING
FUT 10000-003
MAR15
28-42-72
FUT 10000-003
2-400
PAGE
9
MAR 01/15
28-42-72

FUT 10000-004
1
MAR15
ZONING DATA
___________
ZONE
: 522
622
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
: 01
01
01
01
01
01
EXPENDABLE
: 01 O-RING
05 SCREW
284270
284270

(DISPLAY UNITS
EXPLORATION)
EDGES
31-63-00-PRO-10000
ACCESS PLATFORM 4M (13FT)

INTERFACE CABLE
INTERFACE CABLE
INTERFACE CABLE
ADAPTOR
_________
MAN-HOURS
PSD60-2R
PSD40-556YYY
PSD40-556ZZZ
PSD40-555-1
98S28005002-000
PUBLICATION
___________
JIC
JIC
AH
57-54-20-OAC-10000
28-42-72
FUT 10000-004
2-400 PAGE
1
MAR 01/15
28-42-72

001
FUT 10000-004
2
MAR15

___________________________________
EXPLORATION)
____________
_______________________
316300-PRO-10000
DISPLAY UNITS (DU).
002
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
*** CONTINUED ***

AH
28-42-72
FUT 10000-004
2-400 PAGE
2
MAR 01/15
28-42-72

003
FUT 10000-004
3
MAR15
CROSSCHECK OF FUEL QUANTITY INDICATION

______________________________________
PART (1/2)
__________
ON MFD UPPER WINDOW (ENGINE SD PAGE):
FOR LH TANK PRELIMINARY INDICATION:
________ KG.
FOR RH TANK PRELIMINARY INDICATION:
________ KG.
004
___________
PREPARATION
1QT FUEL/FCU CHAN 1
2QT FUEL/FCU CHAN 2
3. PROVIDE ACCESS PLATFORM 4M (13FT) FOR
4. PROVIDE FUEL QUANTITY TEST SET AND
INTERFACE CABLES.
005
___________________________________________
OPENING
575420-OAC-10000
*** CONTINUED ***

AH
28-42-72
FUT 10000-004
2-400 PAGE
3
MAR 01/15
28-42-72

006
FUT 10000-004
4
MAR15
REMOVAL OF PROBES FROM TANKS

____________________________
(WITHOUT DISCONNECTING)
_______________________
REF. FIG. 284272-RAI-00100
NOTE : CONNECT GROUND OF FUEL TEST SET TO
AIRPLANE STRUCTURE.
1. REMOVE AND DISCARD SCREWS (4) FROM FUEL
QUANTITY PROBES.
2. REMOVE AND DISCARD O-RING (3).
3. BY USING THE EXTRACT HOLES (6), REMOVE AND
PLACE PROBES ON WINGS WITHOUT DISCONNECTING
THEIR CONNECTOR.
NOTE : CHECK CONDITION OF EACH DISCONNECTED
PLUG CONNECTOR AND RECEPTACLE CONNECTOR
- DAMAGE OF PINS AND INSULATION
- OXIDATION
- CORRECT CONNECTION OF LOCKING SYSTEM.
- REMOVE, IF NECESSARY, THE ELECTRICAL
FUSE INSTALLED ON REAR SPAR CONNECTORS
007
__________________________________
FUNCTIONAL
TEST OF PROBES ON WINGS
REF. FIG. 284272-FUT-00120
SET (PROBE 1: INTERFACE CABLE -556YYY)
- CHECK THAT PROBE (A) VALUE IS 8.5 +/0.8 PF, AND RECONNECT CONNECTOR.
- CHECK THAT PROBE (B) VALUE IS 12.9 +/0.5 PF, AND RECONNECT CONNECTOR.
*** CONTINUED ***
AH
28-42-72
FUT 10000-004
2-400 PAGE
4
MAR 01/15
28-42-72

FUT 10000-004
5
MAR15

- CHECK THAT PROBE (C) VALUE IS 51.4 +/0.5 PF, AND RECONNECT CONNECTOR.
- CHECK THAT PROBE (D) VALUE IS 18.7 +/0.5 PF, AND RECONNECT CONNECTOR.
- CHECK THAT PROBE (E) VALUE IS 38.65 +/0.5 PF, AND RECONNECT CONNECTOR.
- CHECK THAT PROBE (F) VALUE IS 14.5 +/0.5 PF, AND RECONNECT CONNECTOR.
008
_______________________________________
CLOSING
575420-OAC-10000
009
________________________
FUNCTIONAL
TEST IN CABIN
AVIONIC DOOR 811.
2. DISCONNECT CONNECTORS B1 AND B2 FROM
FCU PLUGS B1 AND B2.
3. TOTAL CAPACITANCE MEASUREMENT (LEFT TANK):
A. CONNECT THE CONNECTOR B1 ON SET TEST BY
USING ADAPTOR 98S28005002-000 AND
CABLE 555-1.
B. PERFORM THE MEASUREMENT OF TOTAL SYSTEM
*** CONTINUED ***
AH
28-42-72
FUT 10000-004
2-400 PAGE
5
MAR 01/15
28-42-72

FUT 10000-004
6
MAR15
CAPACITANCE:
NOTE: THE CAPACITANCE VALUE MUST BE
INCLUDED BETWEEN 143.2 PF AND
148 PF
4. TOTAL CAPACITANCE MEASUREMENT (RIGHT TANK):
A. CONNECT THE CONNECTOR B2 ON SET TEST BY
USING ADAPTOR 98S28005002-000 AND
CABLE 555-1.
B. PERFORM THE MEASUREMENT OF
TOTAL SYSTEM CAPACITANCE:
NOTE: THE CAPACITANCE VALUE MUST BE
INCLUDED BETWEEN 143.2 PF AND
148 PF
5. CONNECT CONNECTORS B1 AND B2 ON FCU
PLUGS B1 AND B2.
CORRECTLY PLACED.
010
__________________________________
RE-INSTALLATION
OF PROBES ON TANKS
REF.FIG. 284272-RAI-00100
R
R
R
R
1. CHANGE THE O-RING, WHICH MUST BE PREVIOUSLY

LUBRICATED WITH CLEAN FUEL. INSTALL EACH
PROBE (TAKE CARE OF THE POSITIONING) INTO
ITS PLACE.
*** CONTINUED ***

AH
28-42-72
FUT 10000-004
2-400 PAGE
6
MAR 01/15
28-42-72

011
FUT 10000-004
7
MAR15
________
CLOSE-UP
1. REMOVE WARNING NOTICE.
2. ON PANEL 121VU, REMOVE SAFETY CLIPS AND TAGS
AND CLOSE CIRCUIT BREAKERS PREVIOUSLY
OPENED.
3. REMOVE ACCESS PLATFORM AND MAKE CERTAIN
THAT WORKING AREA IS CLEAN AND CLEAR OF
TOOLS AND MISCELLANEOUS ITEMS OF EQUIPMENT.
012
CROSSCHECK FUEL QUANTITY INDICATION

___________________________________
PART (2/2)
__________
ON MFD UPPER WINDOW (ENGINE SD PAGE):
FOR LEFT TANK WITH INDICATION PREVIOUSLY
(PART 1/2).
FOR RIGHT TANK WITH INDICATION PREVIOUSLY
(PART 1/2).
*****
AH
E N D
O F
T E X T
*****
28-42-72
FUT 10000-004
2-400 PAGE
7
MAR 01/15
28-42-72
8
AH
TEMP/QUANTITY PROBE
FUT 10000-004
MAR15
28-42-72
FUT 10000-004
2-400
PAGE
8
MAR 01/15
28-42-72
9
AH
FUEL QUANTITY
INDICATING
FUT 10000-004
MAR15
28-42-72
FUT 10000-004
2-400
PAGE
9
MAR 01/15
28-42-72
FUNCTIONAL TEST OF
FUEL GAGE
ELECTRICAL FUSE
FUT 10005-002
1
MAR12
ZONING DATA
___________
ZONE
: 530
630
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
MECHANIC
ELAPSED TIME
GSE
: 01 MULTIMETER
___
MEN
_________
MAN-HOURS
00
PUBLICATION
___________
JIC

EDGES
AH
57-54-20-OAC-10000
28-42-72
FUT 10005-002
2-400 PAGE
1
MAR 01/12
28-42-72
FUNCTIONAL TEST OF
FUEL GAGE
ELECTRICAL FUSE
001
FUT 10005-002
2
MAR12
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
1. INSTALL WARNING NOTICE PROHIBITING OPERATION
2. NOTE FUEL QUANTITY IN LH AND RH TANKS
INDICATED BY THE COCKPIT FUEL QTY INDICATOR
FUEL QTY
L.TK: ______________
R.TK: ______________
3. INSTALL PLATFORM TO GAIN ACCESS TO TRAILING
EDGE RH (LH).
*** CONTINUED ***
AH
28-42-72
FUT 10005-002
2-400 PAGE
2
MAR 01/12
28-42-72
FUNCTIONAL TEST OF
FUEL GAGE
ELECTRICAL FUSE
003
FUT 10005-002
3
MAR12
___________________________________________
OPENING
575420-OAC-10000
004
FUNCTIONAL TEST OF FUEL GAGE

____________________________
ELECTRICAL FUSE
_______________
REF.FIG.:284272-FUT-00105
NOTE:THE FOLLOWING PROCEDURE IS THE SAME FOR
ALL FUEL GAGE ELECTRICAL FUSES.
1. REMOVE THE ELECTRICAL CONNECTOR(1)
2. REMOVE THE ELECTRICAL FUSE (2) FROM THE
FUEL GAGE ELECTRICAL SOCKET (3)
REF.FIG.:284272-FUT-00115
3. BY MEANS OF A MULTIMETER AND FOLLOWING
THE ASSOCIATED TABLE OF FIG.284272-FUT-00115
CHECK PIN TO PIN THE ELECTRICAL FUSE(2)
FOR CORRECT VALUE.
4. CAREFULLY REINSTALL THE ELECTRICAL FUSE (2)
ON GAGE ELECTRICAL SOCKET (3).
5. REINSTALL THE ELECTRICAL CONNECTOR (1) ON
ELECTRICAL FUSE (2).
005
_________________________________
CHECK
OF FUEL QUANTITY INDICATION
NOTE THE FUEL QUANTITY IN LH AND RH TANKS
INDICATED BY THE COCKPIT FUEL QTY INDICATOR
AND VERIFY THE CONSISTENCY WITH VALUES NOTED
DURING THE PREPARATION OF THIS TEST.
*** CONTINUED ***

AH
28-42-72
FUT 10005-002
2-400 PAGE
3
MAR 01/12
28-42-72
FUNCTIONAL TEST OF
FUEL GAGE
ELECTRICAL FUSE
006
FUT 10005-002
4
MAR12
_______________________________________
CLOSING
575420-OAC-10000
007
________
CLOSE-UP
AND CLEAR OF TOOLS AND MISCELLANEOUS ITEM
OF EQUIPMENT.
2. CHECK FOR CORRECT CLOSURE THE PANEL
PREVIOUSLY OPENED.
4. REMOVE WARNING NOTICE IN FLIGHT COMPARTMENT.
*****
AH
E N D
O F
T E X T
*****
28-42-72
FUT 10005-002
2-400 PAGE
4
MAR 01/12
28-42-72
5
AH

GAUGE ELECTRICAL FUSE
FUT 10005-002
MAR12
28-42-72
FUT 10005-002
2-400
PAGE
5
MAR 01/12
28-42-72
6
AH
TABLE VALUES OF
ELECTRICAL FUSE
FUT 10005-002
MAR12
28-42-72
FUT 10005-002
2-400
PAGE
6
MAR 01/12
28-42-72
FUNCTIONAL TEST OF
FUEL GAGE
ELECTRICAL FUSE
FUT 10005-003
1
DEC14
ZONING DATA
___________
ZONE
: 530
630
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
MECHANIC
ELAPSED TIME
GSE
: 01 MULTIMETER
___
MEN
_________
MAN-HOURS
00
PUBLICATION
___________
JIC
JIC

(DISPLAY UNITS
EXPLORATION)
EDGES
AH
31-63-00-PRO-10000
57-54-20-OAC-10000
28-42-72
FUT 10005-003
2-400 PAGE
1
DEC 01/14
28-42-72
FUNCTIONAL TEST OF
FUEL GAGE
ELECTRICAL FUSE
001
FUT 10005-003
2
DEC14

___________________________________
EXPLORATION)
____________
_______________________
316300-PRO-10000
DISPLAY UNITS (DU).
002
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
*** CONTINUED ***

AH
28-42-72
FUT 10005-003
2-400 PAGE
2
DEC 01/14
28-42-72
FUNCTIONAL TEST OF
FUEL GAGE
ELECTRICAL FUSE
003
FUT 10005-003
3
DEC14
___________
PREPARATION
2. ON MFD UPPER WINDOW, IN ENGINE SECONDARY SD
PAGE, NOTE FUEL QUANTITY IN LH AND RH TANKS
FUEL QTY
L.TK: ______________
R.TK: ______________
3. INSTALL PLATFORM TO GAIN ACCESS TO TRAILING
EDGE RH (LH).
004
___________________________________________
OPENING
575420-OAC-10000
005
FUNCTIONAL TEST OF FUEL GAGE

____________________________
ELECTRICAL FUSE
_______________
REF.FIG.:284272-FUT-00105
ALL FUEL GAGE ELECTRICAL FUSES.
1. REMOVE THE ELECTRICAL CONNECTOR(1)
2. REMOVE THE ELECTRICAL FUSE (2) FROM THE
FUEL GAGE ELECTRICAL SOCKET (3)
REF.FIG.:284272-FUT-00115
3. BY MEANS OF A MULTIMETER AND FOLLOWING
THE ASSOCIATED TABLE OF FIG.284272-FUT-00115
CHECK PIN TO PIN THE ELECTRICAL FUSE(2)
FOR CORRECT VALUE.
4. CAREFULLY REINSTALL THE ELECTRICAL FUSE (2)
*** CONTINUED ***
AH
28-42-72
FUT 10005-003
2-400 PAGE
3
DEC 01/14
28-42-72
FUNCTIONAL TEST OF
FUEL GAGE
ELECTRICAL FUSE
FUT 10005-003
4
DEC14
ON GAGE ELECTRICAL SOCKET (3).

5. REINSTALL THE ELECTRICAL CONNECTOR (1) ON
ELECTRICAL FUSE (2).
006
_________________________________
CHECK
ON MFD UPPER WINDOW, IN ENGINE SECONDARY SD
PAGE, NOTE THE FUEL QUANTITY IN LH AND RH TANKS
AND VERIFY THE CONSISTENCY WITH VALUES NOTED
DURING THE PREPARATION OF THIS TEST.
007
_______________________________________
CLOSING
575420-OAC-10000
008
________
CLOSE-UP
AND CLEAR OF TOOLS AND MISCELLANEOUS ITEM
OF EQUIPMENT.
2. CHECK FOR CORRECT CLOSURE THE PANEL
PREVIOUSLY OPENED.
*****
AH
E N D
O F
T E X T
*****
28-42-72
FUT 10005-003
2-400 PAGE
4
DEC 01/14
28-42-72
5
AH

GAUGE ELECTRICAL FUSE
FUT 10005-003
DEC14
28-42-72
FUT 10005-003
2-400
PAGE
5
DEC 01/14
28-42-72
6
AH
TABLE VALUES OF
ELECTRICAL FUSE
FUT 10005-003
DEC14
28-42-72
FUT 10005-003
2-400
PAGE
6
DEC 01/14
28-42-72

LOW LEVEL ALERT
FUT 10010-003
1
DEC14
ZONING DATA
___________
ZONE
ACCESS
: 210
400
: 435AL 445AL
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
01 CONTAINER, 5L (1,3 USGAL)
01 DRAIN TOOL WITH A/C PUMP
_________
MAN-HOURS
98S28003002000
PUBLICATION
___________
JIC
JIC
JIC
JIC
: JACKING FOR A/C

: PRECISE LEVELING
SUPPLY
HINGED ENGINE COWLS
AH
07-11-00-JUP-10000
08-22-00-PRO-10000
24-46-00-EAD-10000
54-00-00-OAC-10000
28-42-72
FUT 10010-003
2-400 PAGE
1
DEC 01/14
28-42-72

LOW LEVEL ALERT
001
FUT 10010-003
2
DEC14
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________________
AIRCRAFT
JACKING UP
071100-JUP-10000
003
________________
PRECISE
LEVELING
082200-PRO-10000
004

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
*** CONTINUED ***
AH
28-42-72
FUT 10010-003
2-400 PAGE
2
DEC 01/14
28-42-72

LOW LEVEL ALERT
005
FUT 10010-003
3
DEC14
______________________
CHECK
OF MFC OPERATION
1. ON PANEL 25VU, CHECK THAT THE FOLLOWING
PUSHBUTTON SWITCHES ARE PRESSED
(OFF LEGENDS ARE OFF):
6UA1
6UA2
7UA1
7UA2
006
MFC/1B/FAULT/OFF
MFC/2B/FAULT/OFF
MFC/1A/FAULT/OFF
MFC/2A/FAULT/OFF
___________
PREPARATION
1. INSTALL ACCESS PLATFORM AT LOWER SURFACE.
2. OPEN COWLS OF LEFT (RIGHT) ENGINE 435AL
(445AL) AS FOLLOWS:
007
___________________________________
OPENING
540000-OAC-10000
008
TRANSFERING/DRAINING FUEL
_________________________
BY AIRCRAFT ELECTRIC PUMP
_________________________
REF. FIG. 284272-FUT-00110.
1. MAKE SURE THAT THE TOTAL FUEL QUANTITY IN
TANKS IS LESS THAN 2200 KG (4840 LB). IN
EACH TANK, FUEL MINIMAL QUANTITY MUST BE
UPPER TO 200 KG (441 LB). TO OBTAIN DESIRED
QUANTITY, USE DESCRIBED PROCEDURE IN JOB
INSTRUCTION CARD (AMM): 121100-DFG-10000.
2. ON PANEL 25VU, MAKE SURE THAT FUEL/X FEED
FLOWBAR IS CROSS LINE.
3. CHECK LEFT SIDE LOW LEVEL SYSTEM:
A. UNSCREW UNION (3) AND DISENGAGE LINE
(2) FROM LEFT ENGINE FUEL HEATER.
*** CONTINUED ***
AH
28-42-72
FUT 10010-003
2-400 PAGE
3
DEC 01/14

LOW LEVEL ALERT
28-42-72
FUT 10010-003
4
DEC14
B. INSTALL END FITTING (4) OF THE TOOL

98S28003002000 ON LINE (2).
MAKE SURE THAT HOSE ASSEMBLY (5) IS CORRECTLY CONNECTED TO END FITTING (4).
ON RIGHT WING, INSTALL HOSE (7) INTO THE
REFUEL GRAVITY PORT (8). IF NECESSARY,
ADD A PIECE OF HOSE.
THIS PROCEDURE PERMITS TO PERFORM FUEL
TRANSFER FROM ONE TANK TO THE ANOTHER.
C. OPEN VALVE (6) OF TOOL.
(1)ON PANEL 25VU, PRESS ENG 1(2)/PUMP
PUSHBUTTON SWITCH. RUN LEGEND COMES
ON. THE RELATED PUMP OPERATES.
(2)WHEN LOW LEVEL LIGHT COMES ON, ON
FUEL QUANTITY INDICATOR ON PANEL 4VU:
- ON CREW ALERTING PANEL, FUEL LIGHT
COMES ON
- ON PANELS 3VU AND 5VU, MASTER
CAUTION LIGHTS COME ON
- SINGLE SHIME SOUNDS.
D. ON TOOL, CLOSE VALVE (6)
(1)ON PANEL 25VU, RELEASE ENG 1(2)/PUMP
PUSHBUTTON SWITCH. RUN LEGEND GOES
OFF, OFF LEGEND COMES ON.
INHIBIT WARNINGS.
(2)ON LEFT (RIGHT) WING, REMOVE FEEDER
TANK ACCESS PANEL 522CT (622CT).
THIS ENABLES TO VISUALLY CONTROL FUEL
LEVEL IN FEEDER TANK.
E. ON PANEL 25VU, PRESS ENG 1(2)/PUMP
PUSHBUTTON SWITCH. RUN LEGEND COMES ON.
THE RELATED PUMP OPERATES.
(1)ON LEFT (RIGHT) WING, CHECK THAT
FEEDER TANK IS REFUELED WHEN ELECTRIC
PUMP OPERATES.
(2)WHEN THE FEEDER TANK IS COMPLETELY
FULL, QUICKLY OPEN VALVE (6) OF TOOL
TO AVOID FUEL SPILLAGE.
*** CONTINUED ***
AH
28-42-72
FUT 10010-003
2-400 PAGE
4
DEC 01/14
28-42-72

LOW LEVEL ALERT
FUT 10010-003
5
DEC14
(3)MAKE SURE THAT SOME FUEL CONTINUES TO

BE TRANSFERRED FROM ONE TANK TO ANOTHER BEFORE FUEL LEVEL DROPS IN LEFT
(RIGHT) FEEDER TANK.
F. ON PANEL 25VU, RELEASE ENG 1(2)/PUMP
PUSHBUTTON SWITCH. RUN LEGEND LIGHT
GOES OFF, OFF LEGEND COMES ON.
INHIBIT WARNINGS.
G. REMOVE HOSE (7) FROM REFUEL GRAVITY PORT.
NOTE: PLACE END OF TUBE INTO A CONTAINER
TO DRAIN THE FUEL FROM HOSES (5)
AND (7) OF TOOL.
WHEN HOSES ARE EMPTY, DISCONNECT END (4)
AND REMOVE TOOL.
H. LOOSEN. BUT DO NOT UNSCREW UNION (1).
INSTALL UNION (3) ON ENGINE FUEL HEATER.
CAUTION :
SIMULTANEOUSLY INSTALL UNIONS (1) AND (3)
THE INSTRUCTIONS BELOW MUST BE OBSERVED
TO INSTALL LINE (2):
- DO NOT TIGHTEN ONE UNION ONLY.
- MANUALLY SCREW BOTH UNIONS SIMULTANEOUSLY AND CHECK THAT LINE IS NOT
TWISTED.
- TIGHTEN UNIONS.
4. CHECK OF RIGHT LOW LEVEL SYSTEM:
DO THE SAME TEST AGAIN BUT CONNECT TOOL
TO RIGHT ENGINE FUEL HEATER LINE.
009
___________________________________
CLOSING
540000-OAC-10000
*** CONTINUED ***

AH
28-42-72
FUT 10010-003
2-400 PAGE
5
DEC 01/14
28-42-72

LOW LEVEL ALERT
010
FUT 10010-003
6
DEC14
____________________________________
LOWERING
071100-JUP-10000
011

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
012
________
CLOSE-UP
6. REMOVE PLATFORM.
*****
AH
E N D
O F
T E X T
*****
28-42-72
FUT 10010-003
2-400 PAGE
6
DEC 01/14
28-42-72
7
AH
INSTALLATION FOR CHECK

FUEL LOW LEVEL ALARM
FUT 10010-003
DEC14
28-42-72
FUT 10010-003
2-400
PAGE
7
DEC 01/14
28-42-72

LOW LEVEL ALERT
FUT 10010-004
1
DEC14
ZONING DATA
___________
ZONE
ACCESS
: 210
400
: 435AL 445AL
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELAPSED TIME
GSE
01 CONTAINER, 5L (1,3 USGAL)
01 DRAIN TOOL WITH A/C PUMP
_________
MAN-HOURS
98S28003002000
PUBLICATION
___________
JIC
JIC
JIC
JIC
JIC

(DISPLAY UNITS
EXPLORATION)
: JACKING FOR A/C
: PRECISE LEVELING
SUPPLY
HINGED ENGINE COWLS
AH
31-63-00-PRO-10000
07-11-00-JUP-10000
08-22-00-PRO-10000
24-46-00-EAD-10000
54-00-00-OAC-10000
28-42-72
FUT 10010-004
2-400 PAGE
1
DEC 01/14
28-42-72

LOW LEVEL ALERT
001
FUT 10010-004
2
DEC14

___________________________________
EXPLORATION)
____________
_______________________
316300-PRO-10000
DISPLAY UNITS (DU).
002
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
*** CONTINUED ***

AH
28-42-72
FUT 10010-004
2-400 PAGE
2
DEC 01/14
28-42-72

LOW LEVEL ALERT
003
FUT 10010-004
3
DEC14
___________________
AIRCRAFT
JACKING UP
071100-JUP-10000
004
________________
PRECISE
LEVELING
082200-PRO-10000
005

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
006
______________________
CHECK
OF MFC OPERATION
6UA1
6UA2
7UA1
7UA2
007
MFC/1B/FAULT/OFF
MFC/2B/FAULT/OFF
MFC/1A/FAULT/OFF
MFC/2A/FAULT/OFF
___________
PREPARATION
1. INSTALL ACCESS PLATFORM AT LOWER SURFACE.
2. OPEN COWLS OF LEFT (RIGHT) ENGINE 435AL
(445AL) AS FOLLOWS:
008
___________________________________
OPENING
540000-OAC-10000
*** CONTINUED ***

AH
28-42-72
FUT 10010-004
2-400 PAGE
3
DEC 01/14

LOW LEVEL ALERT
009
28-42-72
FUT 10010-004
4
DEC14
TRANSFERING/DRAINING FUEL
_________________________
BY AIRCRAFT ELECTRIC PUMP
_________________________
REF. FIG. 284272-FUT-00110.
1. MAKE SURE THAT THE TOTAL FUEL QUANTITY IN
TANKS IS LESS THAN 2200 KG (4840 LB). IN
EACH TANK, FUEL MINIMAL QUANTITY MUST BE
UPPER TO 200 KG (441 LB). TO OBTAIN DESIRED
QUANTITY, USE DESCRIBED PROCEDURE IN JOB
INSTRUCTION CARD (AMM): 121100-DFG-10000.
2. ON PANEL 25VU, MAKE SURE THAT FUEL/X FEED
FLOWBAR IS CROSS LINE.
CROSSFEED VALVE IS CLOSED AND FLOWBAR
IS CROSS LINE.
3. CHECK LEFT SIDE LOW LEVEL SYSTEM:
A. UNSCREW UNION (3) AND DISENGAGE LINE
(2) FROM LEFT ENGINE FUEL HEATER.
B. INSTALL END FITTING (4) OF THE TOOL
98S28003002000 ON LINE (2).
MAKE SURE THAT HOSE ASSEMBLY (5) IS CORRECTLY CONNECTED TO END FITTING (4).
ON RIGHT WING, INSTALL HOSE (7) INTO THE
REFUEL GRAVITY PORT (8). IF NECESSARY,
ADD A PIECE OF HOSE.
THIS PROCEDURE PERMITS TO PERFORM FUEL
TRANSFER FROM ONE TANK TO THE ANOTHER.
C. OPEN VALVE (6) OF TOOL.
(1)ON PANEL 25VU, PRESS ENG 1(2)/PUMP
PUSHBUTTON SWITCH. RUN LEGEND COMES
- RUN LEGEND COMES ON.
- THE RELATED PUMP OPERATES.
ON MFD UPPER WINDOW, IN ENGINE SD PAGE
- ENG 1(2) ELECTRIC PUMP IS RUN.
(2)ON MFD UPPER WINDOW, IN ENGINE SD PAGE
WHEN FEEDER TANK IS DISPLAY IN AMBER:
*** CONTINUED ***
AH
28-42-72
FUT 10010-004
2-400 PAGE
4
DEC 01/14

LOW LEVEL ALERT
28-42-72
FUT 10010-004
5
DEC14
- ON EWD, IN ALERT WINDOW, FUEL LO

LVL MESSAGE IS DISPLAYED
- MASTER CAUTION LIGHTS COME ON
- SINGLE SHIME SOUNDS.
D. ON TOOL, CLOSE VALVE (6)
(1)ON PANEL 25VU, RELEASE ENG 1(2)/PUMP
PUSHBUTTON SWITCH.
- RUN LEGEND GOES OFF.
- ENG 1(2) ELECTRIC PUMP IS OFF.
INHIBIT WARNINGS.
(2)ON LEFT (RIGHT) WING, REMOVE FEEDER
TANK ACCESS PANEL 522CT (622CT).
THIS ENABLES TO VISUALLY CONTROL FUEL
LEVEL IN FEEDER TANK.
E. ON PANEL 25VU, PRESS ENG 1(2)/PUMP
PUSHBUTTON SWITCH:
- RUN LEGEND COMES ON.
- ENG 1(2) ELECTRIC PUMP IS RUN.
THE RELATED PUMP OPERATES.
(1)ON LEFT (RIGHT) WING, CHECK THAT
FEEDER TANK IS REFUELED WHEN ELECTRIC
PUMP OPERATES.
(2)WHEN THE FEEDER TANK IS COMPLETELY
FULL, QUICKLY OPEN VALVE (6) OF TOOL
TO AVOID FUEL SPILLAGE.
(3)MAKE SURE THAT SOME FUEL CONTINUES TO
BE TRANSFERRED FROM ONE TANK TO ANOTHER BEFORE FUEL LEVEL DROPS IN LEFT
(RIGHT) FEEDER TANK.
F. ON PANEL 25VU, RELEASE ENG 1(2)/PUMP
PUSHBUTTON SWITCH:
- RUN LEGEND LIGHT GOES OFF,
ON MFD UPPER WINDOW, IN ENGINE SD PAGE:
- ENG 1(2) ELECTRIC PUMP IS OFF.
*** CONTINUED ***
AH
28-42-72
FUT 10010-004
2-400 PAGE
5
DEC 01/14
28-42-72

LOW LEVEL ALERT
FUT 10010-004
6
DEC14
INHIBIT WARNINGS.
G. REMOVE HOSE (7) FROM REFUEL GRAVITY PORT.
NOTE: PLACE END OF TUBE INTO A CONTAINER
TO DRAIN THE FUEL FROM HOSES (5)
AND (7) OF TOOL.
WHEN HOSES ARE EMPTY, DISCONNECT END (4)
AND REMOVE TOOL.
H. LOOSEN. BUT DO NOT UNSCREW UNION (1).
INSTALL UNION (3) ON ENGINE FUEL HEATER.
CAUTION :
SIMULTANEOUSLY INSTALL UNIONS (1) AND (3)
THE INSTRUCTIONS BELOW MUST BE OBSERVED
TO INSTALL LINE (2):
- DO NOT TIGHTEN ONE UNION ONLY.
- MANUALLY SCREW BOTH UNIONS SIMULTANEOUSLY AND CHECK THAT LINE IS NOT
TWISTED.
- TIGHTEN UNIONS.
4. CHECK OF RIGHT LOW LEVEL SYSTEM:
DO THE SAME TEST AGAIN BUT CONNECT TOOL
TO RIGHT ENGINE FUEL HEATER LINE.
010
___________________________________
CLOSING
540000-OAC-10000
011
____________________________________
LOWERING
071100-JUP-10000
012

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
*** CONTINUED ***
AH
28-42-72
FUT 10010-004
2-400 PAGE
6
DEC 01/14
28-42-72

LOW LEVEL ALERT
013
FUT 10010-004
7
DEC14
________
CLOSE-UP
6. REMOVE PLATFORM.
*****
AH
E N D
O F
T E X T
*****
28-42-72
FUT 10010-004
2-400 PAGE
7
DEC 01/14
28-42-72
8
AH
INSTALLATION FOR CHECK

FUEL LOW LEVEL ALARM
FUT 10010-004
DEC14
28-42-72
FUT 10010-004
2-400
PAGE
8
DEC 01/14
28-42-72
FUNCTIONAL TEST OF
FEEDER TANK LOW LEVEL
SENSOR
FUT 10020-003
1
DEC14
ZONING DATA
___________
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
___
MEN
_________
MAN-HOURS
PUBLICATION
___________
JIC
SUPPLY
AH
24-46-00-EAD-10000
28-42-72
FUT 10020-003
2-400 PAGE
1
DEC 01/14
28-42-72
FUNCTIONAL TEST OF
SENSOR
001
FUT 10020-003
2
DEC14
___________
PREPARATION
REF. FIG. 284272-FUT-00140
NOTE 1:
AVOID TO START THE ENGINE 1 AND 2 AS WELL AS
THE FUEL ELECTRICAL PUMPS 1 AND 2 AT LEAST
THIRTY MINUTES OR MORE BEFORE TO PERFORM THE
TEST.
NOTE 2:
IF TEST IS NOT STATISFACTORY, WAIT OVERNIGHT
TO ALLOW THE FEED FUEL TANK TO EMPTY,THEN
REPEAT THE TEST.
1. ON OVERHEAD PANEL 25VU CHECK THAT THE
FOLLOWING PUSH-BOTTON SWITCHES ARE PRESSED:
6UA1
6UA2
7UA1
7UA2
002
MFC/1B/FAULT/OFF
MFC/2B/FAULT/OFF
MFC/1A/FAULT/OFF
MFC/2A/FAULT/OFF

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
003
FUNCTIONAL TEST OF FEEDER TANK LOW LEVEL

________________________________________
SENSOR.
_______
NOTE:
PERFORM THIS TEST FOR BOTH THE FUEL PUMP AND
BOTH THE MFC (1/2) MODULE }B}.
REF. FIG. 284272-FUT-00140
1.
MAKE SURE THAT MFC 1A/2A AND 1B/2B

PUSHBUTTON ARE RELEASED. (FOUR FAULT/OFF
LEGENDS ARE ON).
*** CONTINUED ***
AH
28-42-72
FUT 10020-003
2-400 PAGE
2
DEC 01/14
28-42-72
FUNCTIONAL TEST OF
SENSOR
FUT 10020-003
3
2.
PRESS MFC 1B (2B) PUSHBUTTON.

FAULT/OFF LEGEND GOES OFF
3.
MAKE SURE THAT FEEDER FUEL TANK IS NOT

FULL.
4.
MAKE SURE THAT FUEL QUANTITY INTO FUEL TANK

IS ABOVE 160KG.(352 LBS) WITH NO LOW LEVEL
LIGHT ILLUMINATED ON FQI.
5.
PULL OUT THE FUEL PUMP CIRCUIT BREAKER 1QA

AND 2QAFUEL/FUELFEED/ENG1(ENG2) ELEC PUMP
6.
MAKE SURE THAT FUEL PUMP CIRCUIT BREAKER

3QA AND 4QA FUEL/FUELFEED/ENG1(ENG2) CTL
& CAUT ARE CLOSED.
7.
PRESS FUEL/ENG1/PUMP PUSHBUTTON 11QA

(FUEL/ENG2/PUMP PUSHBUTTON 12QA)
(NOTE:RUN INDICATION WILL NOT ILLUMINATE)
8.
AFTER ABOUT 10MN, CHECK THAT:

ON FQI LH(RH) SIDE,LOW LVL LIGHT COMES ON
ON CAP FUEL LIGHT COMES ON
ON 4VU CAUTION LIGHT FLASHES
SINGLE CHIME SOUND.
9.
CLEAR CAUTION LIGHT. ALARMS DISAPPEARS.
DEC14
10. RELEASE FUEL/ENG1(2)/PUMP 11QA (12QA)

PUSHBUTTON.
004
________
CLOSE-UP
REF. FIG. 284272-FUT-00140
CLEAR OF TOOLS AND MISCELLANEUS ITEMS OF
EQUIPEMENTS.
*** CONTINUED ***

AH
28-42-72
FUT 10020-003
2-400 PAGE
3
DEC 01/14
28-42-72
FUNCTIONAL TEST OF
SENSOR
005
FUT 10020-003
4
DEC14

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
*****
AH
E N D
O F
T E X T
*****
28-42-72
FUT 10020-003
2-400 PAGE
4
DEC 01/14
28-42-72
5
AH
FUNCTIONAL TEST OF FE
EDER TANK LOW LEVEL
SENSOR
FUT 10020-003
DEC14
28-42-72
FUT 10020-003
2-400
PAGE
5
DEC 01/14
28-42-72
FUNCTIONAL TEST OF
SENSOR
FUT 10020-004
1
DEC14
ZONING DATA
___________
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
___
MEN
_________
MAN-HOURS
PUBLICATION
___________
JIC
JIC

(DISPLAY UNITS
EXPLORATION)
SUPPLY
AH
31-63-00-PRO-10000
24-46-00-EAD-10000
28-42-72
FUT 10020-004
2-400 PAGE
1
DEC 01/14
28-42-72
FUNCTIONAL TEST OF
SENSOR
001
FUT 10020-004
2
DEC14

___________________________________
EXPLORATION)
____________
_______________________
316300-PRO-10000
DISPLAY UNITS (DU).
002
___________
PREPARATION
REF. FIG. 284272-FUT-00140
NOTE 1:
AVOID TO START THE ENGINE 1 AND 2 AS WELL AS
THE FUEL ELECTRICAL PUMPS 1 AND 2 AT LEAST
THIRTY MINUTES OR MORE BEFORE TO PERFORM THE
TEST.
NOTE 2:
IF TEST IS NOT STATISFACTORY, WAIT OVERNIGHT
TO ALLOW THE FEED FUEL TANK TO EMPTY,THEN
REPEAT THE TEST.
1. ON OVERHEAD PANEL 25VU CHECK THAT THE
FOLLOWING PUSH-BOTTON SWITCHES ARE PRESSED:
6UA1
6UA2
7UA1
7UA2
003
MFC/1B/FAULT/OFF
MFC/2B/FAULT/OFF
MFC/1A/FAULT/OFF
MFC/2A/FAULT/OFF

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
*** CONTINUED ***
AH
28-42-72
FUT 10020-004
2-400 PAGE
2
DEC 01/14
28-42-72
FUNCTIONAL TEST OF
SENSOR
004
FUT 10020-004
3
DEC14
FUNCTIONAL TEST OF FEEDER TANK LOW LEVEL

________________________________________
SENSOR.
_______
NOTE:
PERFORM THIS TEST FOR BOTH THE FUEL PUMP AND
BOTH THE MFC (1/2) MODULE }B}.
REF. FIG. 284272-FUT-00140
1.
MAKE SURE THAT MFC 1A/2A AND 1B/2B

PUSHBUTTON ARE RELEASED. (FOUR FAULT/OFF
LEGENDS ARE ON)
2.
PRESS MFC 1B (2B) PUSHBUTTON.

FAULT/OFF LEGEND GOES OFF
3.
MAKE SURE THAT FEEDER FUEL TANK IS NOT

FULL.
4.
MAKE SURE THAT:

- FUEL QUANTITY INTO FUEL TANK IS ABOVE
160KG.(352 LBS) BY NO LO LEVEL
INDICATION ON OUTER PART OF FUEL
INDICATION (MFD UPPER WINDOW, ENGINE SD
PAGE),
- FEEDER TANK IS NOT DISPLAYED IN AMBER ON
INNER PART OF FUEL INDICATION (MFD UPPER
WINDOW, IN ENGINE SD PAGE)
5.
PULL OUT THE FUEL PUMP CIRCUIT BREAKER 1QA

AND 2QAFUEL/FUELFEED/ENG1(ENG2) ELEC PUMP
6.
MAKE SURE THAT FUEL PUMP CIRCUIT BREAKER

3QA AND 4QA FUEL/FUELFEED/ENG1(ENG2) CTL
& CAUT ARE CLOSED.
7.
PRESS FUEL/ENG1/PUMP PUSHBUTTON 11QA

(FUEL/ENG2/PUMP PUSHBUTTON 12QA)
(NOTE:RUN INDICATION WILL NOT ILLUMINATE)
8.
AFTER ABOUT 10MN, CHECK THAT:

*** CONTINUED ***
AH
28-42-72
FUT 10020-004
2-400 PAGE
3
DEC 01/14
28-42-72
FUNCTIONAL TEST OF
SENSOR
FUT 10020-004
4
DEC14
- FEEDER TANK IS DISPLAYED IN AMBER ON

INNER PART OF FUEL INDICATION (MFD UPPER
WINDOW, ENGINE SD PAGE),
- FUEL LO LVL MESSAGE IS DISPLAYED (EWD,
ALERT WINDOW),
- SINGLE CHIME SOUND.
9.
CLEAR CAUTION LIGHT. ALARMS DISAPPEARS.
10. RELEASE FUEL/ENG1(2)/PUMP 11QA (12QA)

PUSHBUTTON.
005
________
CLOSE-UP
REF. FIG. 284272-FUT-00140
CLEAR OF TOOLS AND MISCELLANEUS ITEMS OF
EQUIPEMENTS.
006

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
*****
AH
E N D
O F
T E X T
*****
28-42-72
FUT 10020-004
2-400 PAGE
4
DEC 01/14
28-42-72
5
AH
FUNCTIONAL TEST OF FE
EDER TANK LOW LEVEL
SENSOR
FUT 10020-004
DEC14
28-42-72
FUT 10020-004
2-400
PAGE
5
DEC 01/14
28-42-72
OPERATIONAL TEST OF LOW

LEVEL ALERT INDICATION
SYSTEM
OPT 10000-001
1
DEC14
ZONING DATA
___________
ZONE
ACCESS
: 192
210
: 192JR
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
___
MEN
_________
MAN-HOURS
PUBLICATION
___________
JIC
SUPPLY
AH
24-46-00-EAD-10000
28-42-72
OPT 10000-001
2-400 PAGE
1
DEC 01/14
28-42-72

SYSTEM
001
OPT 10000-001
2
DEC14
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
003
___________
PREPARATION
1. ON RIGHT MAIN LANDING GEAR FAIRING
OPEN REFUELING PANEL ACCESS DOOR (5004VU).
2. PROVIDE EMPTY FUEL TANKER.
*** CONTINUED ***

AH
28-42-72
OPT 10000-001
2-400 PAGE
2
DEC 01/14
28-42-72

SYSTEM
004
OPT 10000-001
3
DEC14
______________________
CHECK
OF MFC OPERATION
6UA1
6UA2
7UA1
7UA2
005
MFC/1B/FAULT/OFF
MFC/2B/FAULT/OFF
MFC/1A/FAULT/OFF
MFC/2A/FAULT/OFF
____________________________________
FUNCTIONAL
TEST OF LOW LEVEL SENSORS
REF. FIG. 282573-FUT-00120
1. ON PANEL 121VU,
CHECK THAT THE FOLLOWING CIRCUIT BREAKERS
ARE CLOSED :
2QU
FUEL/FUEL FUELING/CTL & IND
1QT(2QT) FUEL/FQI/L (R) TANK
1QA(2QA) FUEL/FUEL FEED/ENG1(2)/ELEC
PUMP
3QA(4QA) FUEL/FUEL FEED/ENG1(2)/CTL &
CAUTION.
2. ON REFUELING PANEL 5004VU:
A. PLACE REFUELING/REFUEL/OFF/DEFUELSWITCH
4QU IN DEFUEL POSITION.
B. PLACE REFUELING/REFUEL VALVE/LH(RH)
SWITCH 5QU (6QU) IN OPEN POSITION.
C. REFUELING/LH (RH) VALVE/OPEN LIGHT
151QU(150QU) COMES ON.
D. DEFUEL APPROPRIATE TANK UNTIL LOW LEVEL
THRESHOLD OF 160 KG (352LBS).
(AMM: 121100-DFG-10000).
3. ON PANEL 4VU (COCKPIT), ON FUEL QUANTITY
*** CONTINUED ***
AH
28-42-72
OPT 10000-001
2-400 PAGE
3
DEC 01/14
28-42-72

SYSTEM
OPT 10000-001
4
DEC14
INDICATOR:
A. LO LVL CAUTION LIGHT COMES ON,
. ON CREW ALERTING PANEL FUEL LIGHT
COMES ON
. ON PANELS 3VU AND 5VU, MASTER CAUTION
LIGHTS COME ON
. INGLE CHIME SOUNDS.
- SHUT DOWN DEFUELING OPERATION.
- INHIBE ALARMS.
B. THE VALUE INDICATED IS: 160 KG (352 LBS)
4. ON PANEL 5004VU:
4QU IN OFF POSITION.
B. PLACE 5QU(6QU) SWITCH ON NORM POSITION.
C. REFUELING/LH (RH) VALVE/OPEN LIGHT GOES
OFF.
5. REPEAT THE SAME CHECK FOR OTHER TANK.
006

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
007
________
CLOSE-UP
4. CLOSE REFUELING PANEL DOOR 192JR (EVENTUAL*** CONTINUED ***
AH
28-42-72
OPT 10000-001
2-400 PAGE
4
DEC 01/14
28-42-72

SYSTEM
OPT 10000-001
5
DEC14
LY).
USED).
EQUIPMENT.
*****
AH
E N D
O F
T E X T
*****
28-42-72
OPT 10000-001
2-400 PAGE
5
DEC 01/14
28-42-72
6
AH
DEFUEL/REFUEL PANEL
OPT 10000-001
DEC14
28-42-72
OPT 10000-001
2-400
PAGE
6
DEC 01/14
28-42-72

SYSTEM
OPT 10000-002
1
DEC14
ZONING DATA
___________
ZONE
ACCESS
: 192
210
: 192JR
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
___
MEN
_________
MAN-HOURS
PUBLICATION
___________
JIC
JIC

(DISPLAY UNITS
EXPLORATION)
SUPPLY
AH
31-63-00-PRO-10000
24-46-00-EAD-10000
28-42-72
OPT 10000-002
2-400 PAGE
1
DEC 01/14
28-42-72

SYSTEM
001
OPT 10000-002
2
DEC14

___________________________________
EXPLORATION)
____________
_______________________
316300-PRO-10000
DISPLAY UNITS (DU).
002
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
*** CONTINUED ***

AH
28-42-72
OPT 10000-002
2-400 PAGE
2
DEC 01/14
28-42-72

SYSTEM
003
OPT 10000-002
3
DEC14

___________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
004
___________
PREPARATION
1. ON RIGHT MAIN LANDING GEAR FAIRING
OPEN REFUELING PANEL ACCESS DOOR (5004VU).
2. PROVIDE EMPTY FUEL TANKER.
005
______________________
CHECK
OF MFC OPERATION
6UA1
6UA2
7UA1
7UA2
006
MFC/1B/FAULT/OFF
MFC/2B/FAULT/OFF
MFC/1A/FAULT/OFF
MFC/2A/FAULT/OFF
____________________________________
FUNCTIONAL
TEST OF LOW LEVEL SENSORS
REF. FIG. 282573-FUT-00120
1. ON REFUELING PANEL 100QU:
IN DEFUEL POSITION.
SWITCH IN OPEN POSITION.
C. REFUELING/LH (RH) VALVE/OPEN LIGHT
COMES ON.
D. DEFUEL APPROPRIATE TANK UNTIL LOW LEVEL
THRESHOLD OF 160 KG (352LBS).
*** CONTINUED ***
AH
28-42-72
OPT 10000-002
2-400 PAGE
3
DEC 01/14
28-42-72

SYSTEM
OPT 10000-002
4
DEC14
(AMM: 121100-DFG-10000).
2. A. . ON EWD, IN ALERT WINDOW, FUEL LO LVL
MESSAGE APPEARS.
. MASTER CAUTION LIGHTS FLASH.
. SINGLE CHIME SOUNDS.
- SHUT DOWN DEFUELING OPERATION.
- INHIBE ALARMS.
B. ON MFD UPPER WINDOW, IN ENGINE SD PAGE,
THE VALUE INDICATED IS: 160KG (352LBS)
3. ON PANEL 100QU:
IN OFF POSITION.
SWITCH ON NORM POSITION.
C. REFUELING/LH (RH) VALVE/OPEN LIGHT GOES
OFF.
4. REPEAT THE SAME CHECK FOR OTHER TANK.
007

______________________________________________
FREQUENCY NETWORK
_________________
244600-EAD-10000
008
________
CLOSE-UP
4. CLOSE REFUELING PANEL DOOR 192JR (EVENTUAL*** CONTINUED ***
AH
28-42-72
OPT 10000-002
2-400 PAGE
4
DEC 01/14
28-42-72

SYSTEM
OPT 10000-002
5
DEC14
LY).
USED).
EQUIPMENT.
*****
AH
E N D
O F
T E X T
*****
28-42-72
OPT 10000-002
2-400 PAGE
5
DEC 01/14
28-42-72
6
AH
DEFUEL/REFUEL PANEL
OPT 10000-002
DEC14
28-42-72
OPT 10000-002
2-400
PAGE
6
DEC 01/14
28-42-72

TEMP/QUANTITY PROBE
RAI 10000-003
1
DEC14
ZONING DATA
___________
ZONE
ACCESS
: 522
622
: 522BT 522DT 522ET 523CT 523DT 523FT
622BT 622DT 622ET 623CT 623DT 623FT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
GSE
: 01 TOP WING ACCESS PLATFORM
SPARE
: 01
01
01
01
01
01
PROBE
PROBE
PROBE
PROBE
PROBE
PROBE
EXPENDABLE
: 02
02
03
02
02
02
02
02
01
01
02
02
NUT
NUT
CLAMP
CLAMP
CLAMP
CLAMP
O-RING
O-RING
O-RING
O-RING
NUT
NUT
AH
___
MEN
RIB
RIB
RIB
RIB
RIB
RIB
4/5
5/6
14/15
18/19
9/10
21/22
_________
MAN-HOURS
284270-01-030
284270-01-040
284270-02-030
284270-02-040
284270-03-030
284270-05-030
284270-03-070
284270-05-090
284270-01
284270-02
284270-03
284270-05
284270-01-020
284270-02-020
284270-03-020
284270-05-020
284270-01-090
284270-02-090
28-42-72
RAI 10000-003
2-400 PAGE
1
DEC 01/14

TEMP/QUANTITY PROBE
28-42-72
RAI 10000-003
2
DEC14
PUBLICATION
___________
JIC
: FUNCTIONAL TEST OF FUEL

QUANTITY INDICATOR
AH
28-42-00-FUT-10000
28-42-72
RAI 10000-003
2-400 PAGE
2
DEC 01/14
28-42-72

TEMP/QUANTITY PROBE
001
RAI 10000-003
3
DEC14
_________
PRINCIPLE
ALL LH AND RH WING PROBES ALLOW TO MESURE
FUEL QUANTITY.
NEVERTHELESS, ON AIRCRAFT EQUIPPED WITH NAS
(NEW AVIONIC SUITE), THE FIRST PROBE CLOSER
TO FUSELAGE (EACH SIDE) ALLOWS TO MESURE
EITHER FUEL QUANTITY AND TEMPERATURE.
002
_______
WARNING
WARNING C.D.C.C.L.
CONTROL LIMITATION
CONTROL LIMITATION.
CONFIGURATION.
003
_______________________________
FUEL
REQUIREMENTS.
*** CONTINUED ***
AH
28-42-72
RAI 10000-003
2-400 PAGE
3
DEC 01/14
28-42-72

TEMP/QUANTITY PROBE
RAI 10000-003
4
DEC14

TRANSFER ONLY).
004
___________
PREPARATION
1. MAKE CERTAIN THAT FUEL LEVEL IS BELOW THE
LEVEL OF WORKING AREA.
(PERFORM DEFUELLING OPERATION IF NECESSARY)
3. INSTALL ACCESS PLATFORM TO GAIN ACCESS TO
THE WING UPPER SIDE.
005
REMOVAL OF FUEL QUANTITY OR FUEL TEMP/QUANTITY

______________________________________________
PROBE
_____
REF. FIG. 284272-RAI-00100
1. REMOVE SCREWS (4) RETAINING FUEL QUANTITY
PROBE.
2. BY MEANS OF THE EXTRACT HOLE (6), SLIGHTLY
LIFT FUEL QUANTITY PROBE AND DISCONNECT
PLUG(S) FROM CONNECTOR(S) (2).
NOTE : MARK THE MOST LOWER TYRAP POSITION
ON HARNESS AND FUEL QUANTITY PROBE.
3. REMOVE SCREW (7), WASHER (8), NUT (9) AND
DISCARD IT.
*** CONTINUED ***
AH
28-42-72
RAI 10000-003
2-400 PAGE
4
DEC 01/14
28-42-72

TEMP/QUANTITY PROBE
RAI 10000-003
5
4. REMOVE CLAMPS (5) ATTACHING

PROBE. DISCARD THE CLAMP.
DEC14
WIRING TO THE
5. REMOVE PROBE.
6. REMOVE AND DISCARD PROBE SEAL (3).
7. BLANK EQUIPMENT CONNECTORS.
AS ADJACENT AREA.
NOTE : -TAKE ALL NECESSARY PRECAUTIONS TO
ENSURE THAT ELECTRICAL HARNESSES DO
NOT FALL INTO TANK.
-CHECK AGGREGATION STATE OF FIXED
PLUG (EXTERNAL LEAKAGE MARK) OF TANK
REAR PARTITION.
006
INSTALLATION OF FUEL QUANTITY OR FUEL

_____________________________________
TEMP/QUANTITY PROBE
___________________
REF. FIG. 284272-RAI-00130
REF. FIG. 284272-RAI-00100
1. REMOVE BLANKS.
REQUIRED).
3. CLEAN BONDING PLATE AND APPLY A SLIGHT FILM
OF MASTINOX 6856K.
5. INSTALL CLAMP (5) ATTACHING WIRINGTO THE
PROBE WITH SCREW (7), WASHER (8) AND NEW
NUT (9).
6. MAKE CERTAIN THAT ELECTRICAL CONNECTOR(S)
*** CONTINUED ***
AH
28-42-72
RAI 10000-003
2-400 PAGE
5
DEC 01/14
28-42-72

TEMP/QUANTITY PROBE
RAI 10000-003
6
DEC14
IS (ARE) IN GOOD CONDITION.

NOTE : PROBE N3 IS PROVIDED WITH FOOL-PROOFING :
- GREEN BUSH OR MARKING PROBE ON PROBE
- MARKING COMPENSATOR ON COMPENSATOR
PROBE.
7. CONNECT ELECTRICAL CONNECTOR(S) (2).
REF. FIG. 284272-RAI-00130
8. ALIGN FUEL WIRING (1) ON PROBE
(FORMING A COIL) AND ATTACH IT,
- FIRST IN THE LOWEST POSITION USING
CORRESPONDING TYRAP (2)
- THEN ON MID PROBE HEIGHT USING
CORRESPONDING TYRAP (3).
9. SLOWLY INTRODUCE PROBE ON TANK AND FIX THE
THIRD TYRAP (4) ON PROBE IN HIGHEST
POSITION PLACING THE WIRE IN A U
FORM IN ORDER TO ADJUST THE WIRE LENGTH.
THIS IS IN ORDER TO AVOID A POTENTIAL RISK
OF CHAFING BETWEEN WIRE AND FUEL LINE.
REF. FIG. :284272-RAI-00100
10. PLACE IMMERSED SECTION OF PROBE IN CLEAN
FUEL.
11. INSTALL FUEL QUANTITY PROBE.
12. INSTALL SCREWS (4) AND TIGHTEN.
007
TEST OF FUEL QUANTITY INDICATORS : READING OF

_____________________________________________
FUEL QUANTITY INDICATORS.
_________________________
284200-FUT-10000
*** CONTINUED ***

AH
28-42-72
RAI 10000-003
2-400 PAGE
6
DEC 01/14
28-42-72

TEMP/QUANTITY PROBE
008
RAI 10000-003
7
DEC14
________
CLOSE-UP
6. REMOVE PLATFORM.
*****
AH
E N D
O F
T E X T
*****
28-42-72
RAI 10000-003
2-400 PAGE
7
DEC 01/14
28-42-72
8
AH
TEMP/QUANTITY PROBE
RAI 10000-003
DEC14
28-42-72
RAI 10000-003
2-400
PAGE
8
DEC 01/14
28-42-72
9
AH
WIRE INSTALLATION
ON PROBES
RAI 10000-003
DEC14
28-42-72
RAI 10000-003
2-400
PAGE
9
DEC 01/14
28-42-72

TEMP/QUANTITY PROBE
RAI 10000-004
1
DEC14
ZONING DATA
___________
ZONE
ACCESS
: 522
622
: 522BT 522DT 522ET 523CT 523DT 523FT
622BT 622DT 622ET 623CT 623DT 623FT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
GSE
: 01 TOP WING ACCESS PLATFORM
SPARE
: 01
01
01
01
01
01
PROBE
PROBE
PROBE
PROBE
PROBE
PROBE
EXPENDABLE
: 02
02
03
02
02
02
02
02
01
01
02
02
NUT
NUT
CLAMP
CLAMP
CLAMP
CLAMP
O-RING
O-RING
O-RING
O-RING
NUT
NUT
AH
___
MEN
RIB
RIB
RIB
RIB
RIB
RIB
4/5
5/6
14/15
18/19
9/10
21/22
_________
MAN-HOURS
284270-01-030
284270-01-040
284270-02-030
284270-02-040
284270-03-030
284270-05-030
284270-03-070
284270-05-090
284270-01
284270-02
284270-03
284270-05
284270-01-020
284270-02-020
284270-03-020
284270-05-020
284270-01-090
284270-02-090
28-42-72
RAI 10000-004
2-400 PAGE
1
DEC 01/14

TEMP/QUANTITY PROBE
28-42-72
RAI 10000-004
2
DEC14
PUBLICATION
___________
JIC
: FUNCTIONAL TEST OF FUEL

QUANTITY INDICATOR
AH
28-42-00-FUT-10000
28-42-72
RAI 10000-004
2-400 PAGE
2
DEC 01/14
28-42-72

TEMP/QUANTITY PROBE
001
RAI 10000-004
3
DEC14
_________
PRINCIPLE
ALL LH AND RH WING PROBES ALLOW TO MESURE
FUEL QUANTITY.
NEVERTHELESS, ON AIRCRAFT EQUIPPED WITH NAS
(NEW AVIONIC SUITE), THE FIRST PROBE CLOSER
TO FUSELAGE (EACH SIDE) ALLOWS TO MESURE
EITHER FUEL QUANTITY AND TEMPERATURE.
002
_______
WARNING
WARNING C.D.C.C.L.
CONTROL LIMITATION
CONTROL LIMITATION.
CONFIGURATION.
003
_______________________________
FUEL
REQUIREMENTS.
*** CONTINUED ***
AH
28-42-72
RAI 10000-004
2-400 PAGE
3
DEC 01/14
28-42-72

TEMP/QUANTITY PROBE
RAI 10000-004
4
DEC14

TRANSFER ONLY).
004
___________
PREPARATION
1. MAKE CERTAIN THAT FUEL LEVEL IS BELOW THE
LEVEL OF WORKING AREA.
(PERFORM DEFUELLING OPERATION IF NECESSARY)
3. INSTALL ACCESS PLATFORM TO GAIN ACCESS TO
THE WING UPPER SIDE.
005
REMOVAL OF FUEL QUANTITY OR FUEL TEMP/QUANTITY

______________________________________________
PROBE
_____
REF. FIG. 284272-RAI-00100
PROBE.
2. BY MEANS OF THE EXTRACT HOLE (6), SLIGHTLY
LIFT FUEL QUANTITY PROBE AND DISCONNECT
PLUG(S) FROM CONNECTOR(S) (2).
NOTE : MARK THE MOST LOWER TYRAP POSITION
ON HARNESS AND FUEL QUANTITY PROBE.
3. REMOVE SCREW (7), WASHER (8), NUT (9) AND
DISCARD IT.
*** CONTINUED ***
AH
28-42-72
RAI 10000-004
2-400 PAGE
4
DEC 01/14
28-42-72

TEMP/QUANTITY PROBE
RAI 10000-004
5
4. REMOVE CLAMPS (5) ATTACHING

PROBE. DISCARD THE CLAMP.
DEC14
WIRING TO THE
5. REMOVE PROBE.
6. REMOVE AND DISCARD PROBE SEAL (3).
7. BLANK EQUIPMENT CONNECTORS.
AS ADJACENT AREA.
NOTE : -TAKE ALL NECESSARY PRECAUTIONS TO
ENSURE THAT ELECTRICAL HARNESSES DO
NOT FALL INTO TANK.
-CHECK AGGREGATION STATE OF FIXED
PLUG (EXTERNAL LEAKAGE MARK) OF TANK
REAR PARTITION.
006
INSTALLATION OF FUEL QUANTITY OR FUEL

_____________________________________
TEMP/QUANTITY PROBE
___________________
REF. FIG. 284272-RAI-00130
REF. FIG. 284272-RAI-00100
1. REMOVE BLANKS.
REQUIRED).
3. CLEAN BONDING PLATE AND APPLY A SLIGHT FILM
OF MASTINOX 6856K.
5. INSTALL CLAMP (5) ATTACHING WIRINGTO THE
PROBE WITH SCREW (7), WASHER (8) AND NEW
NUT (9).
6. MAKE CERTAIN THAT ELECTRICAL CONNECTOR(S)
*** CONTINUED ***
AH
28-42-72
RAI 10000-004
2-400 PAGE
5
DEC 01/14
28-42-72

TEMP/QUANTITY PROBE
RAI 10000-004
6
DEC14
IS (ARE) IN GOOD CONDITION.

NOTE : PROBE N3 IS PROVIDED WITH FOOL-PROOFING :
- GREEN BUSH OR MARKING PROBE ON PROBE
- MARKING COMPENSATOR ON COMPENSATOR
PROBE.
7. CONNECT ELECTRICAL CONNECTOR(S) (2).
REF. FIG. 284272-RAI-00130
8. ALIGN FUEL WIRING (1) ON PROBE
(FORMING A COIL) AND ATTACH IT,
- FIRST IN THE LOWEST POSITION USING
CORRESPONDING TYRAP (2)
- THEN ON MID PROBE HEIGHT USING
CORRESPONDING TYRAP (3).
9. SLOWLY INTRODUCE PROBE ON TANK AND FIX THE
THIRD TYRAP (4) ON PROBE IN HIGHEST
POSITION PLACING THE WIRE IN A U
FORM IN ORDER TO ADJUST THE WIRE LENGTH.
THIS IS IN ORDER TO AVOID A POTENTIAL RISK
OF CHAFING BETWEEN WIRE AND FUEL LINE.
REF. FIG. :284272-RAI-00100
10. PLACE IMMERSED SECTION OF PROBE IN CLEAN
FUEL.
11. INSTALL FUEL QUANTITY PROBE.
12. INSTALL SCREWS (4) AND TIGHTEN.
007
TEST OF FUEL QUANTITY INDICATORS : READING OF

_____________________________________________
FUEL QUANTITY INDICATORS.
_________________________
284200-FUT-10000
*** CONTINUED ***

AH
28-42-72
RAI 10000-004
2-400 PAGE
6
DEC 01/14
28-42-72

TEMP/QUANTITY PROBE
008
RAI 10000-004
7
DEC14

_______________________________________
(CLEANING/DRYING OF FUEL TEMP PROBE AREA)
_________________________________________
1. CLEAN FUEL TEMP/QUANT PROBE N1 L(R)
ATTACHMENT AREA USING A CLEAN CLOTH.
2. CHECK FOR ABSENCE OF LEAKAGE OR SEEPING AT
FUEL TEMP/QUANT PROBE N1 L(R) JUNCTIONS.
EQUIPMENT.
009

_______________________________________
(INDICATION CHECK)
__________________
2. BY MEANS A THERMOMETER, MEASURE AND NOTE
THE FUEL TEMPERATURE.
4. ON PANEL 121VU, CLOSE CIRCUIT BREAKERS:
- 1QT FUEL/FCU CHAN 1
- 2QT FUEL/FCU CHAN 2
5. CHECK FUEL TEMPERATURE INDICATED ON MFD
UPPER WINDOW SD ENGINE PAGE IS IN
ACCORDANCE WITH THE ONE RECORDED IN THE
THERMOMETER.
010
________
CLOSE-UP
*** CONTINUED ***
AH
28-42-72
RAI 10000-004
2-400 PAGE
7
DEC 01/14
28-42-72

TEMP/QUANTITY PROBE
RAI 10000-004
8
DEC14
6. REMOVE PLATFORM.
*****
AH
E N D
O F
T E X T
*****
28-42-72
RAI 10000-004
2-400 PAGE
8
DEC 01/14
28-42-72
9
AH
TEMP/QUANTITY PROBE
RAI 10000-004
DEC14
28-42-72
RAI 10000-004
2-400
PAGE
9
DEC 01/14
28-42-72
10
AH
WIRE INSTALLATION
ON PROBES
RAI 10000-004
DEC14
28-42-72
RAI 10000-004
2-400
PAGE
10
DEC 01/14
28-42-72

HARNESS
RAI 10010-002
1
DEC14
ZONING DATA
___________
ZONE
: 530
630
540
640
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELECTRIC
___
MEN
_________
MAN-HOURS
01
ELAPSED TIME
SPARE
: 02 SEAL
284270
EXPENDABLE
: 00 SAFETY WIRE
00 MASTINOX
Z2CN18-10
6856K
BULK MATERIAL : ROPE

PUBLICATION
___________
JIC
JIC
: DEFUELLING
: REFUELING
AH
12-11-00-DFG-10000
12-11-00-FLG-10020
28-42-72
RAI 10010-002
2-400 PAGE
1
DEC 01/14
28-42-72

HARNESS
001
RAI 10010-002
2
DEC14
_______
WARNING
WARNING C.D.C.C.L.
CONTROL LIMITATION
CONTROL LIMITATION.
CONFIGURATION.
002
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
*** CONTINUED ***
AH
28-42-72
RAI 10010-002
2-400 PAGE
2
DEC 01/14
28-42-72

HARNESS
RAI 10010-002
3
DEC14

003
__________
DEFUELLING
121100-DFG-10000
NOTE: THIS OPERATION IS TO BE PERFORMED ONLY
FOR REMOVAL OF DOORS LOCATED IN FUEL
AREA.
004
___________
PREPARATION
ALL THE FUEL QUANTITY PROBE HARNESS
1.MAKE CERTAIN THAT FUEL TANK(S) IS (ARE)
EMPTY.
3. INSTALL ACCESS PLATFORM,TO GAIN ACCESS TO
WING TOP SKIN AND TO WING REAR SPAR LH (RH).
4. IN ZONE 530-540/630-640 OPEN ACCESS DOOR
RELATED TO THE HARNESS NEEDS TO BE CHANGED.
005
______________________________
REMOVAL
REF.FIG. 284272-RAI-00110
ON THE UPPER WING PANEL
PROBE.
2. BY MEANS OF THE EXTRACT HOLE (6) SLIGHTLY
LIFT FUEL QUANTITY PROBE.
3. UNSCREW AND REMOVE:SCREW(7) WASHER(8) NUT(9)
*** CONTINUED ***
AH
28-42-72
RAI 10010-002
2-400 PAGE
3
DEC 01/14
28-42-72

HARNESS
RAI 10010-002
4
DEC14
CLAMPS(5) AND (10).

4. DISCONNECT PLUG(S) FROM CONNECTOR(S) (2).
5. REMOVE THE HARNESS FROM THE PROBE,IN THE
SAME TIME MARK THE LOWEST TYRAP POSITION ON
FUEL QTY PROBE AND HARNESS.RECORD THE LENGTH
OF THE HARNESS COILED TO THE PROBE.
6. PROTECT THE FUEL QUANTITY PROBE TO AVOID ANY
DAMAGE AND/OR CONTAMINATION.
7. TIE THE ROPE TO THE DISCONNECTED PLUG(S).
006
______________________________________
REMOVAL
OF FUEL QUANTITY PROBE HARNESS
REF.FIG. 284272-RAI-00120
ON WING REAR SPAR:
1. IDENTIFY THE FUEL QUANTITY PROBE HARNESS
THAT NEEDS TO BE CHANGED (I.E. 501VC, 503VC
505VC....).
2. LOOSEN THE NUT ELECTRICAL PLUG (16) WITHOUT
REMOVE IT.
3. UNSCREW THE BOLT (10) REMOVE THE WASHER (11)
REMOVE THE BRACKET (12).
4. DISASSEMBLY THE ELECTRICAL PLUG (14) FROM
THE BRACKET (12).
6. SMOOTLY PULL OUT THE CABLE FROM ITS METALIC
CONDUIT UNTIL THE CONNECTION ROPE/CABLE,
COMES OUT.
7. DISCONNECT THE ROPE FROM THE CABLE AVOIDING
TO DAMAGE THE COAXIAL CONNECTOR.
*** CONTINUED ***
AH
28-42-72
RAI 10010-002
2-400 PAGE
4
DEC 01/14
28-42-72

HARNESS
007
RAI 10010-002
5
DEC14
___________________________________________
INSTALLATION
REF.FIG. 284272-RAI-00120
ON WING REAR SPAR SIDE:
1. LUBRIFICATE WITH CLEAN FUEL, INSTALL AND
HOLD THE NEW SEAL (13) ON THE BRACKET (12).
2. PUT ON THE NEW HARNESS AND ASSEMBLY THE
ELECTRICAL PLUG (14) BY NUT (16) ON
BRAKET (12).TIGHTEN FOLLOWING THE VALUES
SHOWED IN THE FIGURE.
3. INSTALL SAFETY WIRE (15) (IF INSTALLED).
4. TIE THE ROPE TO THE CABLE,PAY ATTENTION
TO THE COAXIAL CONNECTOR(S)
ON UPPER WING PANEL:
1. BY MEANS OF THE ROPE, SMOOTLY PULL IN THE
HARNESS WHILE,ON WING REAR SPAR SIDE,
HELP THE ELECTRICAL CABLE TO SLOW DOWN
INTO FUEL TANK THEN INTO METALIC CONDUIT.
2. PULL OUT THE HARNESS UNTIL THE CONNECTION
ROPE/CABLE COMES OUT AND THE BRACKET (12)IS
IN ITS CORRECT POSITION TO BE ASSEMBLIED.
3. DISCONNECT THE ROPE FROM THE HARNESS.
MAKE CERTAIN THAT COAXIAL CONNECTOR(S)
IS IN GOOD CONDITION.
REF ITEM 003 STEP 5.
4. MARK THE POSITION OF THE LOWEST TYRAP ON THE
NEW HARNESS USING THE OLD ONE.
5. SECURE THE HARNESS TO AVOID IT FALL INTO
*** CONTINUED ***
AH
28-42-72
RAI 10010-002
2-400 PAGE
5
DEC 01/14
28-42-72

HARNESS
RAI 10010-002
6
DEC14
FUEL TANK.
ON WING REAR SPAR:
6. INSTALL BRACKET (12) BY MEANS OF BOLT (10)
AND WASHER (11).
TIGHTEN BY A TORQUE VALUE OF:
0.40 - 0.50 MDAN (35,4 - 44,2 LBS.IN.)
008
___________________________________
INSTALLATION
REF. FIG. 284272-RAI-00110
1. REMOVE CAPS AND/OR PROTECTION FROM FUEL
QUANTITY PROBE.
2. INSTALL NEW SEAL (3),PREVIOUSLY LUBRIFICATED
WITH CLEAN FUEL,ON FUEL QUANTITY PROBE.
3. INSTALL CLAMP (5) AND(10),TO FIX THE HARNESS
TO PROBE, BY MEANS OF SCREW (7), WASHER (8),
AND NUT (9).
4. ALIGN FUEL QUANTITY PROBE AND HARNESS TYRAP
MARK AND FIX WITH A TYRAP.
COIL HARNESS OVER THE TYRAP AND FIX WITH
SOME OTHER TYRAPS IN ORDER TO AVOID THE
HARNESS CHAFING IN FUEL TANK.
5. CHECK THAT ELECTRICAL CONNECTOR(S) IS(ARE)
IN GOOD CONDITION.
6. CONNECT THE COAXIAL PLUG(S) TO THE FUEL
QUANTITY PROBE.
7. CLEAN PROBE BONDING PLATE AND APPLY A SLIGHT
FILM OF MASTINOX 6856K
8. INSTALL FUEL QUANTITY PROBE BY MEANS OF
*** CONTINUED ***
AH
28-42-72
RAI 10010-002
2-400 PAGE
6
DEC 01/14
28-42-72

HARNESS
RAI 10010-002
7
DEC14
SCREWS (4) AND TIGHTEN.

009
________
CLOSE-UP
1. CLOSE ACCESS PANEL PREVIOUSLY OPENED.
CLEAR OF TOOLS AND MISCELLANEOUS ITEM OF
EQUIPMENT.
5. PARK THE A/C ON A FLAT PLACE OF PARKING AREA
010
_________
REFUELING
121100-FLG-10020
011
________________________________
TEST
REF. FIG. 284272-TST-00130
A. BY MEANS OF REFUELLING OPERATION AND THE
TABLE IN THE FIGURE, CHECK THE CORRECT
FUEL QUANTITY INDICATION.
B. PERFORM A CALIBRATION FROM 0 TO 500 KG
(1100 LBS) FILLING BOTH THE FUEL TANKS BY
STEP OF 100KG (220LBS).
IN THE COCKPIT
ON THE FUEL QUANTITY INDICATOR:
C. FOR EACH STEP, CHECK THAT THE DIFFERENCE:
QUANTITY INTRODUCED-QUANTITY INDICATED
D. CHECK THAT LOW LEVEL INDICATION GOESOFF WHEN
*** CONTINUED ***
AH
28-42-72
RAI 10010-002
2-400 PAGE
7
DEC 01/14
28-42-72

HARNESS
RAI 10010-002
8
DEC14
THE FUEL QUANTITY IS REACHING THE VALUE OF

160KG (353 LBS).
E. COMPETE THE REFUELLING OPERATION FOLLOWING
THE JIC IN USE.
*****
AH
E N D
O F
T E X T
*****
28-42-72
RAI 10010-002
2-400 PAGE
8
DEC 01/14
28-42-72
9
AH
RENOVAL/INSTALLATION OF
FUEL QUANTITY PROBE
RAI 10010-002
DEC14
28-42-72
RAI 10010-002
2-400
PAGE
9
DEC 01/14
28-42-72
10
AH
FUEL QTY PROBE HARNESS
RAI 10010-002
DEC14
28-42-72
RAI 10010-002
2-400
PAGE
10
DEC 01/14
28-42-72
11
AH
RECORDING TABLE OF FUEL

QUANTITY INDICATION
RAI 10010-002
DEC14
28-42-72
RAI 10010-002
2-400
PAGE
11
DEC 01/14
28-42-72

HARNESS
RAI 10010-003
1
DEC14
ZONING DATA
___________
ZONE
: 530
630
540
640
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
ELECTRIC
_________
MAN-HOURS
01
ELAPSED TIME
SPARE
: 02 SEAL
284270
EXPENDABLE
: 00 SAFETY WIRE
00 MASTINOX
Z2CN18-10
6856K
BULK MATERIAL : ROPE

PUBLICATION
___________
JIC
JIC
JIC

(DISPLAY UNITS
EXPLORATION)
: DEFUELLING
: REFUELING
AH
31-63-00-PRO-10000
12-11-00-DFG-10000
12-11-00-FLG-10020
28-42-72
RAI 10010-003
2-400 PAGE
1
DEC 01/14
28-42-72

HARNESS
001
RAI 10010-003
2
DEC14

___________________________________
EXPLORATION)
____________
_______________________
316300-PRO-10000
DISPLAY UNITS (DU).
002
_______
WARNING
WARNING C.D.C.C.L.
CONTROL LIMITATION
CONTROL LIMITATION.
CONFIGURATION.
003
_______________________________
FUEL
REQUIREMENTS.
*** CONTINUED ***
AH
28-42-72
RAI 10010-003
2-400 PAGE
2
DEC 01/14
28-42-72

HARNESS
RAI 10010-003
3
DEC14

TRANSFER ONLY).
004
__________
DEFUELLING
121100-DFG-10000
NOTE: THIS OPERATION IS TO BE PERFORMED ONLY
FOR REMOVAL OF DOORS LOCATED IN FUEL
AREA.
005
___________
PREPARATION
ALL THE FUEL QUANTITY PROBE HARNESS
1.MAKE CERTAIN THAT FUEL TANK(S) IS (ARE)
EMPTY.
3. INSTALL ACCESS PLATFORM,TO GAIN ACCESS TO
WING TOP SKIN AND TO WING REAR SPAR LH (RH).
4. IN ZONE 530-540/630-640 OPEN ACCESS DOOR
RELATED TO THE HARNESS NEEDS TO BE CHANGED.
*** CONTINUED ***
AH
28-42-72
RAI 10010-003
2-400 PAGE
3
DEC 01/14
28-42-72

HARNESS
006
RAI 10010-003
4
DEC14
______________________________
REMOVAL
REF.FIG. 284272-RAI-00110
ON THE UPPER WING PANEL
PROBE.
2. BY MEANS OF THE EXTRACT HOLE (6) SLIGHTLY
LIFT FUEL QUANTITY PROBE.
3. UNSCREW AND REMOVE:SCREW(7) WASHER(8) NUT(9)
CLAMPS(5) AND (10).
4. DISCONNECT PLUG(S) FROM CONNECTOR(S) (2).
5. REMOVE THE HARNESS FROM THE PROBE,IN THE
SAME TIME MARK THE LOWEST TYRAP POSITION ON
FUEL QTY PROBE AND HARNESS.RECORD THE LENGTH
OF THE HARNESS COILED TO THE PROBE.
6. PROTECT THE FUEL QUANTITY PROBE TO AVOID ANY
DAMAGE AND/OR CONTAMINATION.
7. TIE THE ROPE TO THE DISCONNECTED PLUG(S).
007
______________________________________
REMOVAL
REF.FIG. 284272-RAI-00120
ON WING REAR SPAR:
1. IDENTIFY THE FUEL QUANTITY PROBE HARNESS
THAT NEEDS TO BE CHANGED (I.E. 501VC, 503VC
505VC....).
2. LOOSEN THE NUT ELECTRICAL PLUG (16) WITHOUT
REMOVE IT.
3. UNSCREW THE BOLT (10) REMOVE THE WASHER (11)
*** CONTINUED ***
AH
28-42-72
RAI 10010-003
2-400 PAGE
4
DEC 01/14

HARNESS
28-42-72
RAI 10010-003
5
DEC14
REMOVE THE BRACKET (12).

4. DISASSEMBLY THE ELECTRICAL PLUG (14) FROM
THE BRACKET (12).
6. SMOOTLY PULL OUT THE CABLE FROM ITS METALIC
CONDUIT UNTIL THE CONNECTION ROPE/CABLE,
COMES OUT.
7. DISCONNECT THE ROPE FROM THE CABLE AVOIDING
TO DAMAGE THE COAXIAL CONNECTOR.
008
___________________________________________
INSTALLATION
REF.FIG. 284272-RAI-00120
ON WING REAR SPAR SIDE:
1. LUBRIFICATE WITH CLEAN FUEL, INSTALL AND
HOLD THE NEW SEAL (13) ON THE BRACKET (12).
2. PUT ON THE NEW HARNESS AND ASSEMBLY THE
ELECTRICAL PLUG (14) BY NUT (16) ON
BRAKET (12).TIGHTEN FOLLOWING THE VALUES
SHOWED IN THE FIGURE.
3. INSTALL SAFETY WIRE (15) (IF INSTALLED).
4. TIE THE ROPE TO THE CABLE,PAY ATTENTION
TO THE COAXIAL CONNECTOR(S)
1. BY MEANS OF THE ROPE, SMOOTLY PULL IN THE
HARNESS WHILE,ON WING REAR SPAR SIDE,
HELP THE ELECTRICAL CABLE TO SLOW DOWN
INTO FUEL TANK THEN INTO METALIC CONDUIT.
2. PULL OUT THE HARNESS UNTIL THE CONNECTION
*** CONTINUED ***
AH
28-42-72
RAI 10010-003
2-400 PAGE
5
DEC 01/14
28-42-72

HARNESS
RAI 10010-003
6
DEC14
ROPE/CABLE COMES OUT AND THE BRACKET (12)IS

IN ITS CORRECT POSITION TO BE ASSEMBLIED.
3. DISCONNECT THE ROPE FROM THE HARNESS.
MAKE CERTAIN THAT COAXIAL CONNECTOR(S)
IS IN GOOD CONDITION.
REF ITEM 003 STEP 5.
4. MARK THE POSITION OF THE LOWEST TYRAP ON THE
NEW HARNESS USING THE OLD ONE.
5. SECURE THE HARNESS TO AVOID IT FALL INTO
FUEL TANK.
ON WING REAR SPAR:
6. INSTALL BRACKET (12) BY MEANS OF BOLT (10)
AND WASHER (11).
TIGHTEN BY A TORQUE VALUE OF:
0.40 - 0.50 MDAN (35,4 - 44,2 LBS.IN.)
009
___________________________________
INSTALLATION
REF. FIG. 284272-RAI-00110
1. REMOVE CAPS AND/OR PROTECTION FROM FUEL
QUANTITY PROBE.
2. INSTALL NEW SEAL (3),PREVIOUSLY LUBRIFICATED
WITH CLEAN FUEL,ON FUEL QUANTITY PROBE.
3. INSTALL CLAMP (5) AND(10),TO FIX THE HARNESS
TO PROBE, BY MEANS OF SCREW (7), WASHER (8),
AND NUT (9).
4. ALIGN FUEL QUANTITY PROBE AND HARNESS TYRAP
MARK AND FIX WITH A TYRAP.
COIL HARNESS OVER THE TYRAP AND FIX WITH
*** CONTINUED ***
AH
28-42-72
RAI 10010-003
2-400 PAGE
6
DEC 01/14
28-42-72

HARNESS
RAI 10010-003
7
DEC14
SOME OTHER TYRAPS IN ORDER TO AVOID THE

HARNESS CHAFING IN FUEL TANK.
5. CHECK THAT ELECTRICAL CONNECTOR(S) IS(ARE)
IN GOOD CONDITION.
6. CONNECT THE COAXIAL PLUG(S) TO THE FUEL
QUANTITY PROBE.
7. CLEAN PROBE BONDING PLATE AND APPLY A SLIGHT
FILM OF MASTINOX 6856K
8. INSTALL FUEL QUANTITY PROBE BY MEANS OF
SCREWS (4) AND TIGHTEN.
010
________
CLOSE-UP
1. CLOSE ACCESS PANEL PREVIOUSLY OPENED.
CLEAR OF TOOLS AND MISCELLANEOUS ITEM OF
EQUIPMENT.
5. PARK THE A/C ON A FLAT PLACE OF PARKING AREA
011
_________
REFUELING
121100-FLG-10020
012
________________________________
TEST
1. BY MEANS OF REFUELLING OPERATION, CHECK
THE CORRECT FUEL QUANTITY INDICATION.
2. PERFORM A CALIBRATION FROM 0 TO 500 KG
(1100 LBS) FILLING BOTH THE FUEL TANKS BY
*** CONTINUED ***
AH
28-42-72
RAI 10010-003
2-400 PAGE
7
DEC 01/14
28-42-72

HARNESS
RAI 10010-003
8
DEC14
STEP OF 100KG (220LBS).

3. FOR EACH STEP, CHECK THAT THE DIFFERENCE
QUANTITY INTRODUCED-QUANTITY INDICATED
4. ON EWD, IN ALERT WINDOW, CHECK THAT
FUEL LO LVL MESSAGE GOES OFF WHEN THE
FUEL QUANTITY IS REACHING THE VALUE OF
160KG (353 LBS).
5. COMPETE THE REFUELLING OPERATION FOLLOWING
THE JIC IN USE.
*****
AH
E N D
O F
T E X T
*****
28-42-72
RAI 10010-003
2-400 PAGE
8
DEC 01/14
28-42-72
9
AH
RENOVAL/INSTALLATION OF
FUEL QUANTITY PROBE
RAI 10010-003
DEC14
28-42-72
RAI 10010-003
2-400
PAGE
9
DEC 01/14
28-42-72
10
AH
FUEL QTY PROBE HARNESS
RAI 10010-003
DEC14
28-42-72
RAI 10010-003
2-400
PAGE
10
DEC 01/14
28-42-81
FUEL QUANTITY INDICATOR
RAI 10000-002
1
DEC14
ZONING DATA
___________
ZONE
: 120
210
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
_________
MAN-HOURS
ELAPSED TIME
SPARE
: 01 INDICATOR
284280-01-030
: TEST OF FUEL QUANTITY

INDICATOR
28-42-00-TST-10000
PUBLICATION
___________
JIC
AH
28-42-81
RAI 10000-002
2-400 PAGE
1
DEC 01/14
28-42-81
001
RAI 10000-002
2
DEC14
___________
PREPARATION
REF. FIG. 284272-FUT-00100
ON PANEL 121VU,
BREAKERS :
1QT
FUEL/FQI/L TANK
2QT
FUEL/FQI/R TANK
ITEM OF EQUIPMENT CONCERNED BY THE REMOVAL/
INSTALLATION PROCEDURE IS LOCATED ON LOWER
LEFT SECTION OF UPPER CENTER INSTRUMENT
PANEL 4VU.
002
STANDARD REMOVAL OF FLIGHT COMPARTMENT

______________________________________
EQUIPMENT
_________
NOTE:THE SHAPE OF LOCKING COLLARS,THE QUANTITY
OF BINDING SCREWS AS WELL AS THE SHAPE
AND QUANTITY OF CONNECTORS MAY BE DIFFERENT
ACCORDING THE EQUIPMENT.
NEVERTHELESS,THE REMOVAL AND INSTALLATION
PROCEDURE IS IDENTICAL.
REF. FIG. 310000-RAI-00101
CAUTION: DO NOT LOOSEN LOCKING COLLAR
ATTACHMENT SCREWS.
1. REMOVE CABIN PANEL VU (1).
2. SUFFICIENTLY LOOSEN BINDING SCREWS (6) OF
EQUIPMENT LOCKING COLLAR (2) ON CABIN PANEL
VU (1).(DO NOT COMPLETELY UNSCREW).
3. PULL EQUIPMENT (4) ALONG ITS LOCKING COLLAR
(2).
4. DISCONNECT CONNECTORS(3) FROM RECEPTACLE (5)
*** CONTINUED ***
AH
28-42-81
RAI 10000-002
2-400 PAGE
2
DEC 01/14
28-42-81
RAI 10000-002
3
DEC14
5. REMOVE EQUIPMENT (4).

6. INSTALL PROTECTIVE CAP ON EACH CONNECTOR (3)
AND ON EACH RECEPTACLE (5).
003
STANDARD INSTALLATION OF FLIGHT COMPARTMENT

___________________________________________
EQUIPMENT
_________
REF. FIG. 310000-RAI-00101
1. CLEAN AND INSPECT INSTRUMENT CABIN PANEL VU
(1) AND EQUIPMENT (4) INTERFACE AREA.
2. REMOVE PROTECTIVE CAPS INSTALLED ON CONNECTORS (3) AND RECEPTACLES (5).
3. MAKE CERTAIN THAT PINS ARE IN CORRECT CONDITION AND CONNECT CONNECTORS (3) WITH RECEPTACLES (5).
4. INSTALL EQUIPMENT (4) BY SLIDING IT ALONG
ITS LOCKING COLLAR (2).
5. POSITION EQUIPMENT AND TIGHTEN LOCKING COLLAR (2) BINBING SCREWS (6).
6. INSTALL CABIN VU PANEL (1).
004
________
CLOSE-UP
1. ON PANEL 121VU,
REMOVE SAFETY CLIPS AND TAGS AND CLOSE
CIRCUIT BREAKERS: 1QT,2QT
005
_______________________________
TEST
284200-TST-10000
*** CONTINUED ***

AH
28-42-81
RAI 10000-002
2-400 PAGE
3
DEC 01/14
28-42-81
006
RAI 10000-002
4
DEC14
____________________________________
CROSSCHECK
OF FUEL QUANTITY ON BOARD
REF.FIG.284281-CHK-00100
REF.FIG.284281-CHK-00110
CHECK CHOERENCE OF FUEL QUANTITY INDICATED ON
THE FQI AND THE PHYSICAL QUANTITY IN THE
TANKS BY MEAN OF DRIPSTICKS.
SEE JOB INSTRUCTION CARD:
12-11-28 CHK 10000
CONVERT VOLUME OBTAINED THROUGH DRIPSTICK IN
WEIGHT BY MEAN OF CONVERSION TABLE OF FIGURES
TAKING INTO ACCOUNT FUEL DENSITY OF THE DAY.
*****
AH
E N D
O F
T E X T
*****
28-42-81
RAI 10000-002
2-400 PAGE
4
DEC 01/14
28-42-81
5
AH
FLIGHT COMPARTMENT
EQUIPMENT
RAI 10000-002
DEC14
28-42-81
RAI 10000-002
2-400
PAGE
5
DEC 01/14
28-42-81
6
AH
FUEL QUANTITY
INDICATING
RAI 10000-002
DEC14
28-42-81
RAI 10000-002
2-400
PAGE
6
DEC 01/14
28-42-81
7
AH
VOLUME/WEIGHT CROSSCHECK
OF FUEL QUANTITY
RAI 10000-002
DEC14
28-42-81
RAI 10000-002
2-400
PAGE
7
DEC 01/14
28-42-81
8
AH
OF FUEL QUANTITY
RAI 10000-002
DEC14
28-42-81
RAI 10000-002
2-400
PAGE
8
DEC 01/14
28-42-82

OF FUEL QTY REPEATER
RAI 10000-001
1
DEC14
ZONING DATA
___________
ZONE
ACCESS
: 192
: 192JR
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
_________
MAN-HOURS
ELAPSED TIME
SPARE
: 01 REPEATER IND FUEL QTY
284280-060-010
: POWER SUPPLY FROM

BATTERIES
24-31-00-EAD-10000
PUBLICATION
___________
JIC
AH
28-42-82
RAI 10000-001
2-400 PAGE
1
DEC 01/14
28-42-82

001
RAI 10000-001
2
DEC14
___________
PREPARATION
1QT FUEL/FQI LH TANK
2QT FUEL/FQI RH TANK
2QU FUEL/FUELLING CTL & IND
2. OPEN REFUELING PANEL ACCESS DOOR 192JR.
002
__________________________
REMOVE
OF PROTECTIVE COVER
REF. FIG. 284282-RAI-00100
1. REMOVE SCREWS (6) SECURING THE PROTECTIVE
COVER (4).
2. REMOVE THE PROTECTIVE COVER (4) WITH THE
FIXING SUPPORT (5) OF PROTECTIVE COVER DOOR.
003
REMOVAL OF DUAL FUEL

____________________
QUANTITY REPEATER
_________________
REF. FIG. 284282-RAI-00100
1. UNLOOSE THE SCREWS (2) SECURING THE FUEL
QUANTITY REPEATER INDICATOR (1).
2. EXTRACT THE INDICATOR (1).
3. UNPLUG THE ELECTRICAL CONNECTORS (3).
4. PUT BLANKING CAP ON THE ELECTRICAL CONNECTORS.
004
INSTALLATION OF DUAL FUEL

_________________________
QUANTITY REPEATER
_________________
REF. FIG. 284282-RAI-00100
1. REMOVE BLANKING CAP FROM ELECTRICAL CON*** CONTINUED ***
AH
28-42-82
RAI 10000-001
2-400 PAGE
2
DEC 01/14
28-42-82

RAI 10000-001
3
DEC14
NECTORS (3).
2. PLUG IN ELECTRICAL CONNECTORS TO THE FUEL
QUANTITY REPEATER INDICATOR (1).
3. INSERT THE INDICATOR IN THE PANEL STRUCTURE
4. TIGHTEN SCREWS (2).
005
________________________________
INSTALLATION
OF PROTECTIVE COVER
REF. FIG. 284282-RAI-00100
1. INSTALL THE PROTECTIVE COVER (4) WITH THE
FIXING SUPPORT (5).
006
________
CLOSE-UP
OPENED.
007
_________________________________
ENERGIZING
243100-EAD-10000
008
_______________
FUNCTIONAL
TEST
1. CHECK THAT:
ON PANEL 4VU, ON FUEL QUANTITY INDICATOR
(3QT)
ON PANEL 5004VU, ON FUEL QUANTITY REPEATER
(6QT)
THE VALUES ARE IDENTICAL.
*** CONTINUED ***

AH
28-42-82
RAI 10000-001
2-400 PAGE
3
DEC 01/14
28-42-82

009
RAI 10000-001
4
DEC14
____________________________________
DE-ENERGIZING
243100-EAD-10000
010
________
CLOSE-UP
OF EQUIPMENT.
*****
AH
E N D
O F
T E X T
*****
28-42-82
RAI 10000-001
2-400 PAGE
4
DEC 01/14
28-42-82
5
AH
FUEL REPEATER INDICATOR
RAI 10000-001
DEC14
28-42-82
RAI 10000-001
2-400
PAGE
5
DEC 01/14
28-42-83

OF FUEL QTY PRESELECTOR
RAI 10000-001
1
DEC14
ZONING DATA
___________
ZONE
ACCESS
: 192
: 192JR
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
SPARE
: 01 FUEL QTY PRESELECTOR
AH
___
MEN
_________
MAN-HOURS
284280-065-010
28-42-83
RAI 10000-001
2-400 PAGE
1
DEC 01/14
28-42-83

001
RAI 10000-001
2
DEC14
___________
PREPARATION
1QT FUEL/FQI LH TANK
2QT FUEL/FQI RH TANK
2QU FUEL/FUELLING CTL & IND
2. OPEN REFUELING PANEL ACCESS DOOR 192JR.
002
__________________________
REMOVE
OF PROTECTIVE COVER
REF. FIG. 284283-RAI-00100
1. REMOVE SCREWS (6) SECURING THE PROTECTIVE
COVER (4).
2. REMOVE THE PROTECTIVE COVER (4) WITH THE
FIXING SUPPORT (5) OF PROTECTIVE COVER DOOR.
003
_______
REMOVAL
REF. FIG. 284283-RAI-00100
1. UNLOOSE THE SCREWS (2) SECURING THE FUEL
QUANTITY PRESELECTOR (1).
2. EXTRACT THE PRESELECTOR (1).
3. UNPLUG THE ELECTRICAL CONNECTOR (3).
4. PUT BLANKING CAP ON THE ELECTRICAL CONNECTOR.
004
____________
INSTALLATION
REF. FIG. 284283-RAI-00100
1. REMOVE BLANKING CAP FROM ELECTRICAL CONNECTOR (3).
*** CONTINUED ***
AH
28-42-83
RAI 10000-001
2-400 PAGE
2
DEC 01/14
28-42-83

RAI 10000-001
3
DEC14
2. PLUG IN ELECTRICAL CONNECTOR TO THE FUEL

QUANTITY PRESELECTOR (1).
3. INSERT THE PRESELECTOR IN THE PANEL
STRUCTURE.
005
________________________________
INSTALLATION
OF PROTECTIVE COVER
REF. FIG. 284283-RAI-00100
1. INSTALL THE PROTECTIVE COVER (4) WITH THE
FIXING SUPPORT (5).
006
________
CLOSE-UP
OPENED.
007
_______________
FUNCTIONAL
TEST
1. WHEN REFUELING, CHECK THAT ELECTROVALVES
CLOSE AT THE VALUE DISPLAYED ON PRESELECTOR.
2. VERIFY THE SAME VALUES ON THE BOTH FUEL
QUANTITY INDICATORS 3QT (4VU) AND 6QT
(5004VU).
008
________
CLOSE-UP
OF EQUIPMENT.
*****
AH
E N D
O F
T E X T
*****
28-42-83
RAI 10000-001
2-400 PAGE
3
DEC 01/14
28-42-83
4
AH
PRESELECTOR
RAI 10000-001
DEC14
28-42-83
RAI 10000-001
2-400
PAGE
4
DEC 01/14
28-42-84

OF FUEL CONTROL UNIT
RAI 10000-001
1
DEC14
ZONING DATA
___________
ZONE
ACCESS
: 214
: 0811
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
___
MEN
_________
MAN-HOURS
ELAPSED TIME
SPARE
: 01 FUEL CONTROL UNIT
284210

(DISPLAY UNITS
EXPLORATION)
: OPERATIONAL TEST OF FWD
COMPT DOOR WARNING
31-63-00-PRO-10000
PUBLICATION
___________
JIC
JIC
AH
52-41-00-OPT-10000
28-42-84
RAI 10000-001
2-400 PAGE
1
DEC 01/14
28-42-84

001
RAI 10000-001
2
DEC14

___________________________________
EXPLORATION)
____________
_______________________
316300-PRO-10000
DISPLAY UNITS (DU).
002
___________
PREPARATION
1. ON PANEL 120VU,
A. OPEN
1QT
2QT
2QU
THE FOLLOWING CIRCUIT BREAKERS:

FUEL/FCU CHAN 1
FUEL/FCU CHAN 2
FUEL/FUELING CTL & IND

AVIONNIC DOOR 811.
003
____________________________
REMOVAL
REF. FIG. 284284-RAI-00100
1. DISCONNECT ELECTRICAL CONNECTORS FROM
FUEL CONTROL UNIT (1) AND INSTALL PROTECTIVE CAP.
2. INSTALL PREOTECTIVE CAP ON THE FUEL CONTROL
*** CONTINUED ***
AH
28-42-84
RAI 10000-001
2-400 PAGE
2
DEC 01/14
28-42-84

RAI 10000-001
3
DEC14
UNIT (1).
3. REMOVE SCREWS (2) AND WASHERS (3).
4. REMOVE FUEL CONTROL UNIT (1).
004
_________________________________
INSTALLATION
REF. FIG. 284284-RAI-00100
1. INSTALL THE CONTROL UNIT (1).
2. INSTALL WASHERS (3) AND SCREWS (2) AND
TIGHTEN SCREWS.
3. REMOVE PROTECTIVE CAPS.
4. CONNECT ELECTRICAL CONNECTORS (TO FUEL
CONTROL UNIT).
005
________
CLOSE-UP
CLEAR OF TOOLS OR MISCELLANEOUS ITEM OF
EQUIPMENT.
CORRECTLY PLACED.
4. CLOSE CIRCUIT BREAKERS PREVIOUSLY OPENED.
006
_____________________________________
OPERATIONAL
TEST OF FUEL CONTROL UNIT
ON MFD UPPER WINDOW, IN ENGINE SECONDARY SD
PAGE, VERIFY THAT THE FUEL QUANTITIES MATCH
WITH THE EXPECTED VALUES.
*** CONTINUED ***

AH
28-42-84
RAI 10000-001
2-400 PAGE
3
DEC 01/14
28-42-84

007
RAI 10000-001
4
DEC14
____________________________________
CROSSCHECK
OF FUEL QUANTITY ON BOARD
REF.FIG.284281-CHK-00100
REF.FIG.284281-CHK-00110
CHECK COHERENCE OF FUEL QUANTITY INDICATED ON
MFD UPPER WINDOW, IN ENGINE SECONDARY PAGE AND
THE PHYSICAL QUANTITY IN THE TANK BY MEAN OF
DRIPSTICKS.
SEE JOB INSTRUCTION CARD:
12-11-28 CHK 10000
CONVERT VOLUME OBTAINED THROUGH DRIPSTICK IN
WEIGHT BY MEAN OF CONVERSION TABLE OF FIGURES
TAKING INTO ACCOUNT FUEL DENSITY OF THE DAY.
008
__________________________________________
OPERATIONAL
TEST OF FWD COMPT DOOR WARNING
524100-OPT-10000
*****
AH
E N D
O F
T E X T
*****
28-42-84
RAI 10000-001
2-400 PAGE
4
DEC 01/14
28-42-84
5
AH

RAI 10000-001
DEC14
28-42-84
RAI 10000-001
2-400
PAGE
5
DEC 01/14
28-42-84
6
AH
OF FUEL QUANTITY
RAI 10000-001
DEC14
28-42-84
RAI 10000-001
2-400
PAGE
6
DEC 01/14
28-42-84
7
AH
OF FUEL QUANTITY
RAI 10000-001
DEC14
28-42-84
RAI 10000-001
2-400
PAGE
7
DEC 01/14
28-43-71

OF MANUAL MAGNETIC
INDICATOR
RAI 10000-001
1
MAR12
ZONING DATA
___________
ZONE
ACCESS
: 522
622
: 522AZ 522BB 522CT 523CT 523GT
622AZ 622BB 622CT 623CB 623GT
PREPARATION
___________
PROVISION
WORK
: SKILL
_____
ELAPSED TIME
GSE
: 01 FUEL TANKER
01 ACCESS PLATFORM 3M (10FT)
SPARE
: 02 INDICATOR-MANUAL MAGNETIC
02 INDICATOR-MANUAL MAGNETIC
284370-01
284370-02
EXPENDABLE
: 10
08
02
10
08
02
08
284370-01
284370-01
284370-01
284370-02
284370-02
284370-02
284370-02
O-RING
NUT
SCREW
O-RING
NUT
SCREW
PROTECTIVE CAP
BULK MATERIAL : BALTANE

MEK
PETROLATUM
SEALANT
SEALANT
SEALANT
AH
___
MEN
_________
MAN-HOURS
11-004
11-003
04-012
09-019
09-001
09-002
28-43-71
RAI 10000-001
2-400 PAGE
1
MAR 01/12

OF MANUAL MAGNETIC
INDICATOR
28-43-71
RAI 10000-001
2
MAR12
PUBLICATION
___________
JIC

AH
57-00-00-OAC-10000
28-43-71
RAI 10000-001
2-400 PAGE
2
MAR 01/12
28-43-71

OF MANUAL MAGNETIC
INDICATOR
001
RAI 10000-001
3
MAR12
_______________________________
FUEL
REQUIREMENTS.
TRANSFER ONLY).
002
___________
PREPARATION
ACCESS TO WING LOWER SURFACE AND PLATFORM
3.76 M (12.34 FT), TO GAIN ACCESS TO WING
UPPER SURFACE.
2. DEFUEL COMPLETELY INTO TANKER.
(SEE JOB INST CARD: 121100-DFG-10000)
OF FUEL SYSTEM.
4. FOR INTERNAL MAGNETIC INDICATOR:
- REMOVE ACCESS DOORS 522CT (622CT), 522AZ
*** CONTINUED ***
AH
28-43-71
RAI 10000-001
2-400 PAGE
3
MAR 01/12
28-43-71

OF MANUAL MAGNETIC
INDICATOR
RAI 10000-001
4
MAR12
(622AZ)
FOR EXTERNAL MAGNETIC INDICATOR:
- REMOVE ACCESS DOORS 523HT (623HT), 523GT
(623GT)
USE THE POCEDURE OF WING ACCESS DOORS AS
FOLLOWS :
003
_______________________________
OPENING
570000-OAC-10000
004
REMOVAL OF MANUAL MAGNETIC INDICATOR BETWEEN

____________________________________________
RIB 5 TO 6
__________
REF. FIG. 284371-RAI-00100
1. INTO TANK, REMOVE NUTS (1). DISCARD NUTS.
3. REMOVE MANUAL MAGNETIC INDICATOR (3).
5. CLEAN CARREFULLY SEALANT ON MANUAL MAGNETIC
INDICATOR AND ON MAGNETIC INDICATOR HOUSING
WITH MATERIAL 11-003 AND 11-004B.
AS ADJACENT AREA.
005
REMOVAL OF MANUAL MAGNETIC INDICATOR BETWEEN

____________________________________________
RIB 22 TO 23
____________
REF. FIG. 284371-RAI-00110
1. INTO TANK,
A. REMOVE PROTECTIVE CAP (1).
B. REMOVE NUTS (2). DISCARD NUTS.
*** CONTINUED ***
AH
28-43-71
RAI 10000-001
2-400 PAGE
4
MAR 01/12
28-43-71

OF MANUAL MAGNETIC
INDICATOR
RAI 10000-001
5
MAR12
C. REMOVE SEALANT AROUND THE MANUAL MAGNETIC

INDICATOR BASE.
3. REMOVE MANUAL MAGNETIC INDICATOR (4).
5. CLEAN CARREFULLY SEALANT ON MANUAL MAGNETIC
INDICATOR AND INTO TANK WITH MATERIAL 11-003
11-004B.
AS ADJACENT AREA.
006
INSTALLATION OF MANUAL INDICATOR BETWEEN

________________________________________
RIB 5 AND 6
___________
REF. FIG. 284371-RAI-00100
REQUIRED).
2. INSTALL O-RINGS (4) AND (5). (O-RINGS MUST
BE PREVIOUSLY LUBRICATED WITH MATERIAL
04-012).
3. CLEAN BONDING PLATE AND COAT WITH A FILM OF
GREASE.
4. CLEAN AND INSPECT COMPONENT INTERFACE AND/
OR ADJACENT AREA.
5. APPLY A LAYER OF MATERIAL 09-019 ON MANUAL
MAGNETIC INDICATOR HOUSING).
6. INSTALL MANUAL MAGNETIC INDICATOR (3).
*** CONTINUED ***
AH
28-43-71
RAI 10000-001
2-400 PAGE
5
MAR 01/12
28-43-71

OF MANUAL MAGNETIC
INDICATOR
RAI 10000-001
6
MAR12
8. INTO TANK, INSTALL NUTS (1). TIGHTEN.

007
INSTALLATION OF MANUAL INDICATOR BETWEEN

________________________________________
RIB 22 AND 23
_____________
REF. FIG. 284371-RAI-00110
REQUIRED).
2. INSTALL O-RINGS (5) AND (6). (O-RINGS MUST
BE PREVIOUSLY LUBRICATED WITH MATERIAL
04-012).
3. CLEAN BONDING PLATE AND COAT WITH A FILM OF
GREASE.
4. CLEAN AND INSPECT COMPONENT INTERFACE AND/
OR ADJACENT AREA.
5. INSTALL MANUAL MAGNETIC INDICATOR (4).
7. INTO TANK.
A. INSTALL NUTS (2). TIGHTEN (TIGHTENING
TORQUE 44.3 TO 53.1 LBF.IN/ 0.6 TO
0.7 M.DAN).
B. INSTALL PROTECTIVE CAP (1) ON NUTS.
C. APPLY A LAYER OF MATERIAL 09-002 AROUND
MANUAL MAGNETIC INDICATOR.
D. APPLY A LAYER OF MATERIAL 09-001 AROUND
ATTACHMENTS.
008
________
CLOSE-UP
INSTALL ACCESS DOORS 522AZ (622AZ), 522CT
(622CT) AND 523GT (623GT) AS FOLLOWS :
*** CONTINUED ***

AH
28-43-71
RAI 10000-001
2-400 PAGE
6
MAR 01/12
28-43-71

OF MANUAL MAGNETIC
INDICATOR
009
RAI 10000-001
7
MAR12
________________________________
CLOSING
570000-OAC-10000
010
________
CLOSE-UP
6. REMOVE PLATFORM.
011
______________________________________
CHECKING
OF MANUAL MAGNETIC INDICATORS
1. REFUEL FUEL TANK CONCERNED BY REMOVAL OF MANUAL MAGNETIC INDICATOR.
2. CHECK THAT THERE IS NO LEAKAGE AT LEVEL OF
SEALS.
*****
AH
E N D
O F
T E X T
*****
28-43-71
RAI 10000-001
2-400 PAGE
7
MAR 01/12
28-43-71
8
AH
MANUAL MAGNETIC
INDICATOR BETWEEN
RIB 5 AND 6
RAI 10000-001
MAR12
28-43-71
RAI 10000-001
2-400
PAGE
8
MAR 01/12
28-43-71
9
AH
MANUAL MAGNETIC
INDICATOR BETWEEN
RIB 21 AND 22
RAI 10000-001
MAR12
28-43-71
RAI 10000-001
2-400
PAGE
9
MAR 01/12
12 - MAR 01/15
28-10-00-DVI-10005-002
28-10-00-DVI-10010-003
28-21-61-RAI-10000-001
28-21-71-DVI-10000-001
28-21-71-RAI-10000-001
28-21-72-RAI-10000-001
28-21-73-RAI-10000-001
28-21-74-RAI-10000-001
28-21-77-RAI-10000-001
28-21-78-RAI-10010-001
28-21-78-RAI-10030-001
28-21-79-RAI-10000-001
28-42-72-FUT-10000-003
28-42-72-FUT-10000-004
AH
MINOR
MINOR
MINOR
MINOR
MINOR
MINOR
MINOR
MINOR
MINOR
MINOR
MINOR
MINOR
MINOR
MINOR
INFORMATION
INFORMATION
INFORMATION
INFORMATION
INFORMATION
INFORMATION
INFORMATION
INFORMATION
INFORMATION
INFORMATION
INFORMATION
INFORMATION
INFORMATION
INFORMATION
ADDITION
ADDITION
ADDITION
ADDITION
ADDITION
ADDITION
ADDITION
ADDITION
ADDITION
ADDITION
ADDITION
ADDITION
ADDITION
ADDITION
ALL
ALL
ALL
ALL
ALL
ALL
ALL
ALL
ALL
ALL
ALL
ALL
051 TO 062
063 TO 065
12
PAGE
1
MAR 01/15
PAGE
1 TO
10 MAR/15
ALL
1 TO
12 MAR/15
ALL
1 TO
5 APR/05
ALL
1 TO
3 APR/05
ALL
1 TO
3 MAR/11
ALL
1 TO
10 MAR/12
ALL
1 TO
1 TO
4 APR/05
5 MAR/12
ALL
ALL
1 TO
4 MAR/12
ALL
1 TO
5 MAR/12
ALL
1 TO
3 APR/05
ALL
1 TO
4 DEC/14
ALL
1 TO
3 DEC/14
ALL
1 TO
5 DEC/14
51 TO
62
1 TO
5 DEC/14
63 TO
65
1 TO
4 DEC/14
ALL
REVISION NO 12 - MAR/15
R 28-10-00-DVI-10005-002 DETAILED VISUAL

BY VIDEO CAMERA
R 28-10-00-DVI-10010-003 DETAILED VISUAL
28-11-00-CLN-10000-001 CLEANING FOR REMOVAL OF
28-11-00-DVI-10000-001 DETAILLED VISUAL INSPECTION OF WING FUEL
BARRIER PLATE
28-11-00-GVI-10000-001 GENERAL VISUAL INSPECTION OF WING LOWER
SURFACE FUEL LEAK
28-11-72-RAI-10000-001 REMOVAL AND INSTALLATION
28-12-00-DAR-10000-001 INERTING
OF NACA INTAKE
28-12-72-OPT-10000-001 OPERATIONAL TEST OF
FLOAT VALVE
OF VENT FLOAT VALVE
28-20-00-CHK-10010-001 CHECK OF REFUELLING DUCT
28-20-00-CHK-10020-002 REMOVAL OF DOUBLE SKIN
28-20-00-DVI-10000-002 DETAILED VISUAL
DUCT
VENTING VALVE
VENTING VALVE
OF AIRSTREM
AH
1
MAR/15
PAGE
1 TO
6 DEC/14
51 TO
62
1 TO
7 DEC/14
63 TO
65
1 TO
6 DEC/14
51 TO
62
1 TO
8 DEC/14
63 TO
65
1 TO
5 MAR/15
ALL
1 TO
4 MAR/15
ALL
1 TO
6 MAR/15
ALL
1 TO
10 MAR/15
ALL
1 TO
5 MAR/15
ALL
1 TO
5 MAR/15
ALL
1 TO
4 APR/05
ALL
1 TO
7 MAR/15
ALL
1 TO
6 DEC/14
51 TO
62
1 TO
6 DEC/14
63 TO
65
1 TO
6 MAR/15
ALL
1 TO
6 MAR/15
ALL
1 TO
8 MAR/15
ALL
28-20-00-OPT-10030-002 OPERATIONAL TEST OF L/R

28-20-00-OPT-10030-003 OPERATIONAL TEST OF L/R
FEED LO PRESS
INDICATING SYSTEM
FEED LO PRESS
INDICATING SYSTEM
28-21-61-RAI-10000-001 REMOVAL/INSTALLATION OF
SWITCH
HARNESS
CANISTER
28-21-78-FUT-10000-001 FUNCTIONAL TEST OF
NOZZLE ASSY
R
R
R
R
R
R
R
R
AH
2
MAR/15
PAGE
1 TO
8 DEC/14
51 TO
62
1 TO
13 DEC/14
63 TO
65
1 TO
6 MAR/12
ALL
1 TO
5 MAR/12
ALL
1 TO
10 DEC/14
51 TO
62
1 TO
11 DEC/14
63 TO
65
1 TO
6 APR/05
ALL
1 TO
10 DEC/14
51 TO
62
1 TO
11 DEC/14
63 TO
65
1 TO
5 DEC/14
ALL
1 TO
9 MAR/12
ALL
1 TO
5 MAR/12
ALL
1 TO
4 MAR/12
ALL
1 TO
5 DEC/14
63 TO
1 TO
6 MAR/12
ALL
1 TO
5 MAR/12
ALL
1 TO
4 MAR/12
ALL
28-23-00-OPT-10000-002 OPS TEST OF FUEL CROSS

28-23-00-OPT-10000-003 OPS TEST OF FUEL CROSS
ACTUATOR
28-24-00-FUT-10000-002 FUNCTIONAL TEST OF FUEL
LP VALVE
LP VALVE
28-24-00-FUT-10010-001 LEAKAGE TEST OF FUEL
FEED PIPES
28-24-00-OPT-10000-002 OPERATIONAL TEST OF LP
28-24-00-OPT-10000-003 OPERATIONAL TEST OF LP
28-24-00-OPT-10010-001 OPERATIONAL TEST OF THE
FUEL LP VALVE
PANEL (RCP)
ASSEMBLY
OF REFUEL/DEFUEL
ELECTROVALVE
INSPECTION OF HIGH
LEVEL SENSOR
AH
65
3
MAR/15
PAGE
1 TO
5 DEC/14
51 TO
62
1 TO
5 DEC/14
63 TO
65
1 TO
5 MAR/12
ALL
1 TO
6 DEC/14
ALL
1 TO
7 DEC/14
51 TO
62
1 TO
5 DEC/14
51 TO
62
1 TO
5 DEC/14
51 TO
62
1 TO
6 DEC/14
63 TO
65
1 TO
6 DEC/14
51 TO
62
1 TO
6 DEC/14
63 TO
65
1 TO
8 DEC/14
51 TO
62
1 TO
7 DEC/14
63 TO
65
1 TO
5 DEC/14
51 TO
62
1 TO
4 MAR/12
ALL
1 TO
9 MAR/15
51 TO
62
1 TO
9 MAR/15
63 TO
65
1 TO
6 MAR/12
51 TO
54 TO
58 TO
52
56
62
28-25-73-FUT-10000-001 FUNCTIONAL TEST OF HIGH

CLOSURE OF VALVES
28-25-73-FUT-10000-002 FUNCTIONAL TEST OF HIGH
CLOSURE OF VALVES
SENSOR
OF FUEL TEMPERATURE
INDICATOR
QUANTITY INDICATION
QUANTITY INDICATION
LOW LEVEL RANGE
LOW LEVEL RANGE
28-42-00-TST-10000-001 TEST OF FUEL QUANTITY
INDICATOR
INSPECTION OF FUEL
QUANTITY PROBES
R 28-42-72-FUT-10000-003 FUNCTIONAL TEST OF FUEL
R 28-42-72-FUT-10000-004 FUNCTIONAL TEST OF FUEL
FUEL GAGE
ELECTRICAL FUSE
AH
4
MAR/15
PAGE
1 TO
6 DEC/14
63 TO
65
1 TO
7 DEC/14
51 TO
62
1 TO
8 DEC/14
63 TO
65
1 TO
5 DEC/14
51 TO
62
1 TO
5 DEC/14
63 TO
65
1 TO
6 DEC/14
51 TO
62
1 TO
6 DEC/14
63 TO
65
1 TO
9 DEC/14
51 TO
62
1 TO
10 DEC/14
63 TO
65
1 TO
11 DEC/14
51 TO
62
1 TO
10 DEC/14
63 TO
65
1 TO
8 DEC/14
51 TO
62
1 TO
5 DEC/14
51 TO
62
1 TO
4 DEC/14
51 TO
62
1 TO
7 DEC/14
63 TO
65
1 TO
9 MAR/12
ALL

FUEL GAGE
ELECTRICAL FUSE
LOW LEVEL ALERT
LOW LEVEL ALERT
SENSOR
SENSOR
28-42-72-OPT-10000-001 OPERATIONAL TEST OF LOW
SYSTEM
28-42-72-OPT-10000-002 OPERATIONAL TEST OF LOW
SYSTEM
TEMP/QUANTITY PROBE
TEMP/QUANTITY PROBE
HARNESS
HARNESS
OF MANUAL MAGNETIC
INDICATOR
AH
5
MAR/15

Ata 28

Uploaded by

Copyright:

Available Formats

Ata 28

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ata 28

Uploaded by

Copyright:

Available Formats

28-10-00

DETAILED VISUAL INSPECTION OF FUEL PUMP

DETAILED VISUAL INSPECTION OF HIGH LEVEL

DETAILED VISUAL INSPECTION OF FUEL QUANTITY

DETAILED VISUAL INSPECTION OF

REF.:NDTM CHAP.57-11-00 PART 1/9

5. CLAMP CONDITION ON FUEL LINE

-DAMAGE OF ELASTOMER SHEATH ON CLAMP (BROKEN

FUEL LINES INSTALLATION

VENT LINES INSTALLATION

7. ANY SPILLED FUEL MUST BE ABSORBED AND DRIED.

LOAD RELIEVING OF OUTER WING

LOAD RELIEVING OF OUTER WING

LOAD RELIEVING OF OUTER WING

*** CONTINUED ***

DETAILED VISUAL INSPECTION OF FUEL PUMP

DETAILED VISUAL INSPECTION OF HIGH LEVEL

DETAILED VISUAL INSPECTION OF FUEL QUANTITY

REMOVAL OF WING REMOVABLE PANELS __________________________________

*** CONTINUED ***

DETAILED VISUAL INSPECTION OF

INSPECT THE FOLLOWING ITEMS:

-DAMAGE OF ELASTOMER SHEATH ON CLAMP (BROKEN

INSTALLATION OF WING REMOVABLE PANELS _______________________________________

FUEL LINES INSTALLATION

VENT LINES INSTALLATION

CLEANING FOR REMOVAL OF

BULK MATERIAL : METHYL ALCOHOL

: DRAINING OF WATER FROM

CLEANING FOR REMOVAL OF

FUEL/FUEL FEED/X FEED

B. DEFUEL THE TANK AND PERFORM A COMPLETE

DRAINING OF WATER FROM

CLEANING FOR REMOVAL OF

REMOVAL OF WING REMOVABLE PANELS __________________________________

CLEANING FOR REMOVAL OF MICROBIOLOGIC DEBRIS

CLEANING FOR REMOVAL OF

3. RINSE WITH CLEAN WATER TO REMOVE DETERGENT

CLEANING FOR REMOVAL OF

USING THE PROCEDURE DESCRIBED INTO THE JOB

INSTALLATION OF WING REMOVABLE PANELS _______________________________________

DETAILLED VISUAL INSPECTION OF WING FUEL

DETAILLED VISUAL INSPECTION OF WING FUEL

DETALLED VISUAL INSPECTION OF FUEL BARRIER

OVERFLOW FUEL BARRIER

GENERAL VISUAL INSPECTION OF WING LOWER

GENERAL VISUAL INSPECTION OF WING LOWER

GENERAL VISUAL INSPECTION OF LOWER WING SURFACE

FUEL LEAK AREA

REMOVAL AND INSTALLATION

: 01 UNDERWING ACCESS PLATFORM

BULK MATERIAL : BALTANE

: OPENING AND CLOSING OF

REMOVAL AND INSTALLATION

: REMOVAL AND INSTALLATION

REMOVAL AND INSTALLATION

REMOVAL AND INSTALLATION

REMOVAL OF WATER DRAINS BETWEEN RIB 5 TO 6

* CONTINUED *

* CONTINUED *

* CONTINUED *

* CONTINUED *

* CONTINUED *