Toshiba 2820C MFP Management Guide

MULTIFUNCTIONAL DIGITAL SYSTEMS
MFP Management Guide
2008 TOSHIBA TEC CORPORATION All rights reserved

Under the copyright laws, this manual cannot be reproduced in any form without prior written permission of TTEC. No patent liability
is assumed, however, with respect to the use of the information contained herein.
Preface
Thank you for purchasing TOSHIBA Multifunctional Digital Systems or Multifunctional Digital Color Systems. This manual
explains the instructions for administrators to set up and manage the Multifunctional Digital Systems or Multifunctional
Digital Color Systems. Read this manual before using your Multifunctional Digital Systems or Multifunctional Digital Color
Systems. Keep this manual within easy reach, and use it to configure an environment that makes the best use of the eSTUDIOs functions.
How to read this manual

Symbols in this manual
In this manual, some important items are marked with the symbols shown below. Be sure to read these items before using
this equipment.
Indicates a potentially hazardous situation which, if not avoided, could result in death, serious
injury, or serious damage, or fire in the equipment or surrounding assets.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate
injury, partial damage to the equipment or surrounding assets, or loss of data.
Indicates information to which you should pay attention when operating the equipment.
Other than the above, this manual also marks information that may be useful for the operation of this equipment with the
following signs:
Describes handy information that is useful to know when operating the equipment.
Pages describing items related to what you are currently doing. See these pages as required.
Screens
y Screens in this manual may differ from the actual displays depending on the use-environment of the equipment, such
as the installed status of options.
y Screens of when paper in the A/B format is used are given in this manual. If you use paper in the LT format, the display
or the order of buttons may differ from that of your equipment.
Trademarks
y
y
y
y
y
y
y
y
y
y
y
y
y
The official name of Windows 2000 is Microsoft Windows 2000 Operating System.
The official name of Windows XP is Microsoft Windows XP Operating System.
The official name of Windows Vista is Microsoft Windows Vista Operating System.
The official name of Windows Server 2003 is Microsoft Windows Server 2003 Operating System.
The official name of Windows Server 2008 is Microsoft Windows Server 2008 Operating System.
Microsoft, Windows, Windows NT, and the brand names and product names of other Microsoft products are
trademarks of Microsoft Corporation in the US and other countries.
Apple, AppleTalk, Macintosh, Mac, Mac OS, Safari, TrueType, and LaserWriter are trademarks of Apple Inc. in the US
and other countries.
Adobe, Adobe Acrobat, Adobe Reader, Adobe Acrobat Reader, and PostScript are trademarks of Adobe Systems
Incorporated.
Mozilla, Firefox and Firefox logo are trademarks or registered trademarks of Mozilla Foundation in the U.S. and other
countries.
IBM, AT and AIX are trademarks of International Business Machines Corporation.
NOVELL, NetWare, and NDS are trademarks of Novell, Inc.
TopAccess is a trademark of Toshiba Tec Corporation.
Other company names and product names in this manual are the trademarks of their respective companies.
Preface
CONTENTS
Preface....................................................................................................................................... 1
Chapter 1
SETTING ITEMS (USER)

Entering User Menu.................................................................................................................. 8
Setting General Functions....................................................................................................... 9
Setting the auto clear mode................................................................................................... 9
Changing the display language ........................................................................................... 10
Setting the reversed display mode ...................................................................................... 11
Adjusting the display contrast.............................................................................................. 12
Setting the calibrations ........................................................................................................ 13
Setting the registration......................................................................................................... 15
Setting Copy Functions ......................................................................................................... 16
Setting Fax Functions ............................................................................................................ 19
Setting Scan Functions.......................................................................................................... 20
Setting e-Filing Functions ..................................................................................................... 23
Printing Lists........................................................................................................................... 24
Setting Drawer ........................................................................................................................ 27
Managing Address Book ....................................................................................................... 30
Managing contacts in address book .................................................................................... 30
Managing groups in address book ...................................................................................... 42
Checking E-mail...................................................................................................................... 58
Setting BIP Printing................................................................................................................ 59
Chapter 2
SETTING ITEMS (ADMIN)

Entering Admin Menu ............................................................................................................ 63
Setting General Functions..................................................................................................... 65
Setting the device information ............................................................................................. 65
Setting the notification ......................................................................................................... 66
Changing the administrator password ................................................................................. 68
Setting the date and time .................................................................................................... 70
Setting the energy saver modes.......................................................................................... 72
Setting the calibration and registration display level............................................................ 76
Setting the drawer set pop-up and paper jam recovery pop-up .......................................... 77
Setting the status message ................................................................................................. 78
Setting the calibration .......................................................................................................... 79
Setting the registration......................................................................................................... 84
Setting the panel calibration ................................................................................................ 85
Setting Network Functions .................................................................................................... 87
Setting the TCP/IP protocol (IPv4) ...................................................................................... 87
Setting the IPv6 protocol ..................................................................................................... 91
Setting the IPX/SPX protocol............................................................................................... 98
Setting the NetWare settings............................................................................................. 100
Setting the SMB protocol................................................................................................... 102
Setting the AppleTalk protocol........................................................................................... 104
Setting the HTTP network service ..................................................................................... 106
Setting the Ethernet speed ................................................................................................ 108
Setting the LDAP/SNMP network services and the filtering functions............................... 109
CONTENTS
IPsec (IP security) setting.................................................................................................. 111

Decrypting the user certificate ........................................................................................... 113
Network check ................................................................................................................... 115
Setting Copy Functions ....................................................................................................... 118
Setting Fax Functions .......................................................................................................... 120
Setting the discard and reduction print option for the RX print .......................................... 120
Setting File Functions .......................................................................................................... 122
Setting E-mail Functions ..................................................................................................... 123
Setting Internet Fax Functions............................................................................................ 124
Setting Security Functions .................................................................................................. 125
Setting List/Report ............................................................................................................... 127
Printing Lists......................................................................................................................... 132
Setting Printer/e-Filing Functions....................................................................................... 133
Wireless Settings and Bluetooth Settings ......................................................................... 134
Change User Password ....................................................................................................... 135
IEEE 802.1X Authentication Setting.................................................................................... 136
Setting IEEE802.1X authentication ................................................................................... 136
Chapter 3
MANAGING COUNTERS (COUNTER MENU)

Total Counter ........................................................................................................................ 152
Print Out Total Counter........................................................................................................ 155
Department Counter............................................................................................................. 156
Managing Department Codes.............................................................................................. 160
Logging on as administrator .............................................................................................. 160
Printing department code list ............................................................................................. 162
Enabling department codes............................................................................................... 163
Resetting all department counters..................................................................................... 164
Deleting all department codes ........................................................................................... 165
Registering a new department code.................................................................................. 166
Editing department codes.................................................................................................. 168
Deleting department codes................................................................................................ 171
Resetting the counter for each department ....................................................................... 172
Setting output limitations for all departments..................................................................... 173
Setting the no limit black function ...................................................................................... 174
Chapter 4
APPENDIX
List Print Format................................................................................................................... 178
Total counter list ................................................................................................................ 178
Department code list.......................................................................................................... 179
Address book information.................................................................................................. 180
Group number information................................................................................................. 181
Function list (User) ............................................................................................................ 182
NIC configuration page...................................................................................................... 183
Function list (Administrator)............................................................................................... 184
CONTENTS
PS3 font list ....................................................................................................................... 198

PCL font list ....................................................................................................................... 199
INDEX ................................................................................................................................................................... 201
CONTENTS
CONTENTS
SETTING ITEMS (USER)
1.
Entering User Menu ................................................................................................................. 8

Setting General Functions....................................................................................................... 9
Setting the auto clear mode ...................................................................................................................................9
Changing the display language ............................................................................................................................10
Setting the reversed display mode ....................................................................................................................... 11
Adjusting the display contrast...............................................................................................................................12
Setting the calibrations .........................................................................................................................................13
Setting the registration .........................................................................................................................................15
Setting Copy Functions ......................................................................................................... 16

Setting Fax Functions............................................................................................................ 19
Setting Scan Functions ......................................................................................................... 20
Setting e-Filing Functions ..................................................................................................... 23
Printing Lists .......................................................................................................................... 24
Setting Drawer ........................................................................................................................ 27
Managing Address Book ....................................................................................................... 30
Managing contacts in address book .....................................................................................................................30
Managing groups in address book .......................................................................................................................42
Checking E-mail ..................................................................................................................... 58

Setting BIP Printing................................................................................................................ 59
1 SETTING ITEMS (USER)
Entering User Menu

Follow the steps below to enter the USER menu in the USER FUNCTIONS screen.
Press the [USER FUNCTIONS] button on the control panel to enter the USER
FUNCTIONS menu.
Press the [USER] tab.
Continue the user setting operation that you require.
The USER menu is displayed.
P.9 Setting General Functions

P.16 Setting Copy Functions
P.19 Setting Fax Functions
P.20 Setting Scan Functions
P.23 Setting e-Filing Functions
P.24 Printing Lists
P.27 Setting Drawer
P.30 Managing Address Book
P.58 Checking E-mail
P.59 Setting BIP Printing
[BIP PRINTING] is available only when the Bluetooth Module (optional) is installed. For instructions on how to
set the BIP printing, refer to the GN-2010 Operators Manual for Bluetooth Module.
Entering User Menu
Setting General Functions

Setting the auto clear mode
This function sets how long the machine waits before clearing the previous functions set on the control panel.
Press [GENERAL] in the USER menu.
The GENERAL menu is displayed.
To display the USER menu, see the following page:

P.8 Entering User Menu
Press [AUTO CLEAR].
The AUTO CLEAR screen is displayed.
Press the button that indicates the desired time in seconds.
The auto clear mode has been set to the selected time.
If you want to disable the auto clear mode, press [NO LIMIT].
Even if [NO LIMIT] is selected, the screen will be cleared after 45 seconds when users are operating in the
USER FUNCTION, JOB STATUS, or TEMPLATE screen.
Changing the display language

The language used on the touch panel can be changed to a different one.

Press [CHANGE LANGUAGE].
The CHANGE LANGUAGE screen is displayed.
Press the desired language button.
The touch panel is displayed in the selected language.
10

1.SETTING ITEMS (USER)
Setting the reversed display mode

You can change the touch panel to be displayed in the reversed display mode in which the white portion is black and the
black portion is white.
Changing to the reversed display mode helps to display the touch panel more clearly when it is too bright.

Press [REVERSED DISPLAY].
The REVERSED DISPLAY screen is displayed.
11
Press [ON] to enable the reversed display, or [OFF] to disable the reversed display.
When you select [ON], the touch panel is displayed in the reversed display mode.
Adjusting the display contrast

This function allows you to adjust the touch panel contrast.

12

Press [DISPLAY SETTING].
The DISPLAY SETTING menu is displayed.
Adjust the touch panel contrast.
Use
to brighten the touch panel display. Use
to darken the touch panel display.
Setting the calibrations

This function allows the machine to automatically calibrate the color gradation for copy and printing jobs when the color
cannot be adjusted accurately because the shading or the hue of the image has deviated.
y The calibration setting in the USER menu can be configured only when an administrator has set the calibration
display level to [USER].
P.76 Setting the calibration and registration display level
y Place LT or A4 paper (recommended paper) in the drawer before starting the calibration. If any other paper is used,
calibration may not be performed properly.
y If the glass is dirty or any foreign objects are stuck to the glass, the calibration may not be performed properly.
Keep the glass clean.
y Never raise the original cover or the Reversing Automatic Document Feeder, or open the front cover while the
calibration is in progress. If this does happen, the calibration cannot be finished properly.
y Interrupt copying is not available during the calibration.
y If the color often deviates, call your service technician.
Place the paper to be used for the calibration in the drawer.

Place paper in the large capacity feeder if it is installed. If it is not, place paper in the uppermost drawer in which A4
or LT has been registered.
13

Press [CALIBRATION].
The CALIBRATION menu is displayed.
Refer to Step 1 in the following operations.

To perform the copy calibration, see the following page:
P.81 Setting the copy calibration
To perform the print calibration, see the following page:
P.82 Setting the print calibration
Instructions on how to perform the copy and print calibrations are the same when they are performed in the
ADMIN menu.
14

Setting the registration

When color misregistration occurs, this function allows you to align the position of each color.
The registration setting in the USER menu can be configured only when an administrator has set the registration
display level to [USER].

Press [REGISTRATION].
The REGISTRATION menu is displayed.
Refer to Step 3 in the following operation.

P.84 Setting the registration
Instructions on how to perform the registration are the same when it is performed in the ADMIN menu.
15
Setting Copy Functions

You can change the initial settings (defaults) for copy jobs.
Press [COPY] in the USER menu.
The COPY screen is displayed.

Specify the following items as you require and press
EXPOSURE FOR COLOR Press the desired mode button.

EXPOSURE FOR BLACK Press the desired mode button.
COLOR MODE Press the desired mode button. Only [BLACK] can be selected when the no limit black function
is enabled.
IMAGE DIRECTION Press the desired mode button. For details on the image direction option, refer to the
Copying Guide.
16

Press the desired media type button and press
For e-STUDIO2330C/2820C/2830C/3520C/3530C/4520C
For e-STUDIO5520C/6520C/6530C
For more information about the paper type, refer to the Copying Guide.
Press the desired mode button for the ORIGINAL MODE FOR COLOR and ORIGINAL
MODE FOR BLACK options and press
.
17
Specify the following items as you require and press [OK].
ORIGINAL MODE FOR AUTO COLOR Press the desired mode button that applies when you copy documents
in auto color mode.
OMIT BLANK PAGE ADJUSTMENT Use
and
to select the appropriate sensitivity from 7 levels to
detect blank pages from the scanned data in a copy job. The higher the level is, the more likely the equipment is to
detect blank pages. For more information about the omit blank page function, refer to the Copying Guide.
ACS ADJUSTMENT Use the buttons to select the appropriate sensitivity from 7 levels to detect whether the
data scanned in the auto color copy mode is color or black. The higher the level is, the more likely the equipment is
to detect the scanned data as color document.
The default settings are changed as specified.
18
Setting Fax Functions

You can change the initial settings (defaults) for fax and Internet Fax jobs.
If the FAX Unit (optional) is not installed, only three options are available: RESOLUTION, ORIGINAL MODE and
EXPOSURE. For details on other fax options, refer to the GD-1250/GD-1260/GD-1270 Operators Manual for FAX
Unit.
If the FAX Unit (optional) is not installed, the setting items in this menu are applied to Internet Fax transmission jobs.
Press [FAX] in the USER menu.
The FAX screen is displayed.

RESOLUTION Press the desired mode button.

ORIGINAL MODE Press the desired mode button.
EXPOSURE Press the
or
button to specify the default exposure manually, or press [AUTO] to select
auto mode for the default exposure mode.
19
Setting Scan Functions

You can change the initial settings (defaults) for scan jobs.
Press [SCAN] in the USER menu.
The SCAN screen is displayed.

COLOR MODE Press the desired mode button.

COMPRESS Press the desired mode button that applies to scan jobs in gray scale, full color, or auto color
mode.
SINGLE/2-SIDE SCAN Press the desired mode button.
y [SINGLE] Press this button to set single page scan mode as the default scan mode.
y [BOOK] Press this button to set book scan mode as the default scan mode. This enables scans of both
sides of originals in the same direction.
y [TABLET] Press this button to set tablet scan mode as the default scan mode. This enables scans of the
front page in the general direction, and scans of the back page rotated 180 degree.
ROTATION Press the desired mode button.
20

PREVIEW SETTING Press [ON] to enable the preview function to preview the scans before you save or e-mail
them. Press [OFF] to disable the preview function.
INITIAL PREVIEW TYPE Select [PAGE FIT] or [WIDTH FIT] for the preview screen.
OMIT BLANK PAGE ADJUSTMENT Use
and
to select the appropriate sensitivity from 7 levels to
detect blank pages from the scanned data in a scan job. The higher the level is, the more likely the equipment is to
detect blank pages. For more information about the omit blank page function, refer to the Scanning Guide.
ACS ADJUSTMENT Use the buttons to select the appropriate sensitivity from 7 levels to detect whether the
data scanned in the auto color scan mode is color or black. The higher the level is, the more likely the equipment is
to detect the scanned data as a color document.
IMAGE QUALITY FOR BLACK IN ACS Press the desired mode button that applies when scanning a black
original in the auto color mode.
B/W ADJUSTMENT IN ACS Press the
or
button to specify the exposure that applies when scanning a
black original in the auto color mode. If you move to the left, the black and white in an original will be scanned
lightly. If you move to the right, the black and white in an original will be scanned deeply.
RESOLUTION Select the corresponding button for the default resolution applied when scanning in color mode.
ORIGINAL MODE Press the desired mode button applied for color scans.
EXPOSURE Press the
or
button to specify the default exposure for color scans manually, or press
[AUTO] to select auto mode as the default exposure mode for color scans.
BACKGROUND ADJUSTMENT Press the
or
button to specify the contrast for color scans. If you move
to the left, the background color will be lighter. If you move to the right, the background color will be darker.
21
RESOLUTION Select the corresponding button for the default resolution applied when scanning in gray scale
mode.
EXPOSURE Press the
or
button to specify the default exposure for gray scale scans manually, or press
[AUTO] to select auto mode as the default exposure mode for gray scale scans.
or
button to specify the contrast for gray scale scans. If you
move to the left, the background color will be lighter. If you move to the right, the background color will be darker.
RESOLUTION Select the corresponding button for the default resolution applied when scanning in black mode.
ORIGINAL MODE Press the desired mode button applied for black scans.
EXPOSURE Press the
or
button to specify the default exposure for black scans manually, or press
[AUTO] to select auto mode as the default exposure mode for black scans.
or
button to specify the contrast for black scans. If you
move to the left, the background color will be lighter. If you move to the right, the background color will be darker.
22
Setting e-Filing Functions

You can set the image quality type for printing color documents that have been stored by Scan to e-Filing.
Press [E-FILING] in the USER menu.
The E-FILING screen is displayed.

In the PRINTING IMAGE MODE option, press the desired mode button and press [OK].
[GENERAL] Press this button to apply proper color quality for printing a general color document.
[PHOTOGRAPH] Press this button to apply proper color quality for printing photos.
[PRESENTATION] Press this button to apply proper image quality for printing a vivid document.
[LINE ART] Press this button to apply proper image quality for printing a document containing many characters
or line arts.
Setting e-Filing Functions
23
Printing Lists
This function allows you to print the following lists.
y Address Book Information
You can print the address book information that shows all registered contacts in the equipment.
y Group Numbers Information
You can print the group numbers information that shows all registered groups and members in the equipment.
y Function List (User)
You can print the function list that shows the function flow under [USER] of the user functions.
The list is printed on paper that is fed from the drawer in which LT-R or A4-R paper is set and exits to the inner tray.
Press [LIST] in the USER menu.
The LIST menu is displayed.

Continue the operation that you require.
P.25 Printing the address book information

P.26 Printing the group number information
P.26 Printing the function list (User)
24
Printing Lists

Printing the address book information
Press [ADDRESS BOOK].
The ADDRESS BOOK menu is displayed.
Press [ID SORT] to print it as sorted by the ID number, or [NAME SORT] to print it as
sorted by the last name.
y When the department management is disabled, the address book information is printed.
y When the department management is enabled, the screen to input the department code is displayed. Enter the
department code using the digital keys and press [OK] to print the address book information.
For an output example of the address book information, see the following page:
P.180 Address book information
Printing Lists
25
Printing the group number information
Press [GROUP NUMBERS].
y When the department management is disabled, the group number information is printed.
department code using the digital keys and press [OK] to print the group number information.
For an output example of the group number information, see the following page:
P.181 Group number information
Printing the function list (User)
Press [FUNCTION].
y When the department management is disabled, the function list is printed.

department code using the digital keys and press [OK] to print the function list.
For an output example of the function list, see the following page:
P.182 Function list (User)
26
Printing Lists
Setting Drawer
This function allows you to set the paper size and paper type for each drawer.
Press [DRAWER] in the USER menu.
The Drawer screen is displayed.

Press the drawer portion in the illustration to highlight the drawer for which you want
to change the paper size, and press the desired paper size button.
y The selected paper size is displayed in the drawer in the illustration.

y If you want to change the paper type from plain paper to another or want to specify the use purpose of paper in
the drawer, press [PAPER TYPE] and proceed to step 3.
Setting Drawer
27
y The selected paper size is displayed in the drawer in the illustration.

y If you want to change the paper type from plain paper to another or want to specify the use purpose of paper in
the drawer, press [PAPER TYPE] and proceed to step 3.
y Selecting [AUTO (mm)] or [AUTO (inch)] allows the equipment to automatically detect the size of paper in the
drawer. To set A/B format paper such as A3 and A4, press [AUTO (mm)]. To set LT format paper such as LD
and LT, press [AUTO (inch)]. When paper is placed in the drawer, the equipment automatically detects the
paper size.
The equipment may fail to detect the paper size and indicates UNDEF for the drawer if the LT format paper is
placed in the drawer for which [AUTO (mm)] is set or vice versa. In this case, select the correct button.
Press the drawer portion in the illustration to highlight the drawer for which you want
to change the paper type, and press the desired paper type button.
You can select either [RECYCLED PAPER], [THICK1], [THICK2], or [THICK3] for the paper type.
28
Setting Drawer

You can select either [PLAIN 1], [PLAIN 2], [RECYCLED PAPER], [THICK1], [THICK2], or [THICK3] for the paper
type.
y For details on the paper type, refer to the Copying Guide.

y You can select either [INSERT], [COVER], [SPECIAL], or [FAX] to restrict the uses for a specific job. For
example, if you select [INSERT] for a drawer, the paper in the drawer is always used for copy insertion.
Setting Drawer
29
Managing Address Book

Managing contacts in address book
The address book is accessible by pressing [ADDRESS BOOK]. Entries in the address book are used to specify e-mail
addresses and/or fax numbers for fax transmission and Scan to E-mail.
In the address book, you can register up to 1000 contacts, which can contain a fax number, an e-mail address, or both in
each contact. When the FAX Unit (optional) is installed, you can also specify the option settings for the fax transmission in
each contact, such as transmission type, ECM, quality transmission, line select, and subaddress settings.
You can use the registered fax numbers to specify the destinations for fax transmissions only when the FAX Unit
(optional) is installed.
In the ADDRESS BOOK menu, you can perform the following operations to manage contacts.
y P.30 Registering contacts
y P.34 Editing contacts
y P.36 Deleting contacts
y P.38 Searching for contacts
You can import and export address book data in CSV format in the TopAccess administrator mode. For details, refer to
the TopAccess Guide.
Registering contacts
The following two methods can be used to register new contacts in the address book.
P.30 Registering contacts from the [USER FUNCTIONS] button
P.33 Registering contacts from log lists
Registering contacts from the [USER FUNCTIONS] button
Press [ADDRESS] in the USER menu.
The ADDRESS menu is displayed.

30

The ADDRESS BOOK screen is displayed.
Press an undefined button to create a new contact and press [ENTRY].
The ADDRESS BOOK REGISTRATION screen is displayed.
If the touch panel does not display an undefined contact, press
to display the next screen.
31
Press each button on the touch panel to enter the following contact information.
[FIRST NAME] Press this button to enter the first name of the contact. This name will appear in the address
book list on the touch panel.
[LAST NAME] Press this button to enter the last name of the contact. This name will appear in the address book
list on the touch panel.
[FAX NO.] Press this button to enter the fax number of the contact.
[2ND FAX] Press this button to enter the second fax number of the contact.
[E-MAIL] Press this button to enter the e-mail address of the contact.
[CORP.] Press this button to enter the company name of the contact.
[DEPT.] Press this button to enter the department name of the contact.
[KEYWORD] Press this button to enter a keyword for the contact. This keyword can be used to search for this
contact.
y You must at least enter either [FIRST NAME] or [LAST NAME], and either [FAX NO.] or [E-MAIL] to register
the contact.
y Press [PAUSE] on the touch panel to enter - in [FAX NO.] and [2ND FAX]. If you enter - in them, a threesecond pause is added for dialing the fax number.
When you press each button, the on-screen keyboard is displayed. Enter the value using the on-screen
keyboard and digital keys and press [OK] to set the entry.
Press [OPTION] to specify the default settings for a fax transmission.
y This is available only when the FAX Unit (optional) is installed.

y For details on the settings, refer to the GD-1250/GD-1260/GD-1270 Operators Manual for FAX Unit.
Press [OK] to register the contact.
The contact is registered in the address book.
32

Registering contacts from log lists

You can register information such as remote fax numbers and e-mail addresses in the address book from the send/receive
log screen.
The following information can be registered from the Send log:
y Remote fax numbers that were dialed by direct entry using the digital keys, or that were searched for by the LDAP
server
y E-mail addresses that were manually entered, or that were searched for by the LDAP server
The following information can be registered from the Receive log:
y Remote fax numbers that were dialed by direct entry using the digital keys, or that were searched for by the LDAP
server for a polling reception
y E-mail address of the sender
The following information can be registered from the Scan log:
y E-mail addresses that were manually entered
1
2
Press [JOB STATUS] on the touch panel.

Press the [LOG] tab and press [SEND] (or [RECEIVE] or [SCAN]).
The SEND (or RECEIVE or SCAN) LOG list is displayed.
Select the job that includes the fax number or e-mail address you want to register into
the address book, and press [ENTRY].
To register e-mail addresses specified as Bcc contacts into the address book from the scan log, it is necessary
to enable the [Bcc Address Display] option from the TopAccess - Email menu. If the [Bcc Address Display]
option is disabled, the description [Bcc Address] is displayed instead of an e-mail address on the scan log
screen. In this case, even if you select the description [Bcc Address], [ENTRY] cannot be used. For instructions
on how to enable the [Bcc Address Display] option, refer to the TopAccess Guide.
33
Enter the contact information.
For the description of each item, see step 4 in the following operation:

Press [OK] to register the contact.
The contact is registered in the address book.
Editing contacts
You can edit existing contacts in the address book.

34

Press the contact that you want to edit and press [EDIT].
The ADDRESS BOOK EDIT screen is displayed.
y If the touch panel does not display the contact that you want to edit, press
y You can quickly search for the contact that you want to edit. To search for the contact, see the following
page:
P.38 Searching for contacts
Press each button on the touch panel to edit the contact information.

35
Press [OK] to save the contact.
The contact is edited.
Deleting contacts
You can delete existing contact in the address book.

36

Press the contact that you want to delete and press [DELETE].
The delete confirmation screen is displayed.
If the touch panel does not display the contact that you want to delete, press
Press [YES] to delete the contact.
The selected contact is deleted.
Press [NO] to cancel the deletion.
37
Searching for contacts

The following two methods can be used to search the address book for contacts. They are useful to find the contact that
you want to edit.
P.38 Searching for contacts by ID number
P.39 Searching for contacts by entering a search string
Searching for contacts by ID number

Press [KNOWN ID].
The KNOWN ID screen is displayed.
38

Enter the ID Number using the digital keys and press [OK].
The touch panel displays the found contact. Press the contact and press [EDIT] to edit
the contact information, or press [DELETE] to delete the contact.
For instructions on editing the contact, see the following page:

P.34 Editing contacts
Searching for contacts by entering a search string

39
Press [SEARCH].
The ADDRESS SEARCH screen is displayed.
Press the corresponding button(s) for the desired search category.
When you press each button, the on-screen keyboard is displayed.
40

Enter the search string using the keyboard and digital keys, and press [OK].
Contacts that contain the search string for the specified items will be found.
Specify the search string in the items that you require and press [SEARCH].
The touch panel displays the found contacts. Press the desired contact and press [OK]
to edit the contact information.
For instructions on editing the contact, see the following page:

P.34 Editing contacts
41
Managing groups in address book

You can create groups that contain multiple contacts. This enables you to specify groups instead of specifying each
recipient separately when operating Scan to E-mail, or fax or Internet Fax transmissions.
In the address book, you can register up to 200 groups and each group can contain up to 400 members.
y One fax number or one e-mail address is counted as one destination. If you select a contact that contains both a
fax number and an e-mail address, it results in two destinations in the group.
y You can register fax numbers in the groups, however, you can use them to specify the destinations for fax
transmission only when the FAX Unit (optional) is installed.
In the GROUP menu, you can perform the following operations to manage groups.
y P.42 Creating new groups
y P.45 Editing groups
y P.51 Deleting groups
y P.52 Searching for groups
Creating new groups

You can create a new group in the address book.

Press [GROUP].
The GROUP screen is displayed.
42

Press an undefined button to create a new group and press [ENTRY].
The GROUP NO. REGISTRATION screen is displayed.
If the touch panel does not display an undefined group, press
Press [GROUP NAME].
The on-screen keyboard is displayed.
Enter the group name using the keyboard and digital keys, and press [OK].
43
Press [OK].
The CHECK OF GROUP MEMBER screen is displayed.
Select the contacts that you want to add to the group, and then press [OK].
y To add or remove contacts by selecting each contact manually, see the following page:
P.47 Adding or removing contacts
y To add contacts by searching for them by ID number, see the following page:
P.48 Adding contacts by searching by ID number
y To add contacts by searching for them with a search string, see the following page:
P.49 Adding contacts by searching with a search string
44
The new group is created and it appears on the touch panel.

Editing groups
You can edit the names of groups, or add or remove members in groups.
Editing group names

Press [GROUP].
Press the group that you want to edit and press [EDIT].
The GROUP NO. EDIT screen is displayed.
If the touch panel does not display the group that you want to edit, press
45
Press [GROUP NAME] to edit the group name.
Enter the group name using the keyboard and digital keys, and press [OK].
Press [OK].
The CHECK OF GROUP MEMBER screen is displayed.
46

On the screen, the contacts that have been registered in the group are highlighted.
y To add or remove contacts by selecting each contact manually, see the following page:
P.47 Adding or removing contacts
y To add contacts by searching for them by ID number, see the following page:
P.48 Adding contacts by searching by ID number
y To add contacts by searching for them with a search string, see the following page:
P.49 Adding contacts by searching with a search string
Press [OK] to save the settings.
Adding or removing contacts
Press contacts that are not highlighted to add them to the group, or press highlighted
contacts to remove them from the group.
y To add both the fax number and e-mail address of a contact to the group, press the contact name.
y To add only the fax number of a contact to the group, press
in the contact.
y To add only the e-mail address of a contact to the group, press
in the contact.
y Press
or
to display contacts on different pages.
y You can also clear all highlighted contacts by pressing [ALL CLEAR].
Press [OK] to save the group.
47
Adding contacts by searching by ID number
Press [KNOWN ID].
The touch panel displays the found contact. Press the contact to add it to the group.
in the contact.
in the contact.
y Press
or
y You can also clear all highlighted contacts by pressing [ALL CLEAR].
48

Adding contacts by searching with a search string
Press [SEARCH].
The ADDRESS SEARCH screen is displayed.
Press the corresponding button(s) for the desired search category.
When you press each button, the on-screen keyboard is displayed.
Contacts that contain the search string for the specified items will be found.
49
Specify the search string in the items that you require and press [SEARCH].
The touch panel displays the found contacts. Press the contacts that you want to add
to the group.
in the contact.
in the contact.
Press
50
or

Deleting groups
You can delete a group from the address book.

Press [GROUP].
Press the group that you want to delete and press [DELETE].
If the touch panel does not display the group that you want to delete, press
51
Press [YES] to delete the group.
The selected group is deleted.
Searching for groups

The following two methods can be used to search the address book for groups. This function is useful for finding a group
that you want to edit.
P.52 Searching for groups by ID number
P.54 Searching for groups by group name
Searching for groups by ID number

52

Press [GROUP].
Press [KNOWN ID].
53
The touch panel displays the found group. Press the group and press [EDIT] to edit the
group information, or press [DELETE] to delete the group.
For instructions on editing groups, see the following page:

P.45 Editing groups
Searching for groups by group name

Press [GROUP].
54

Press [SEARCH].
The GROUP SEARCH screen is displayed.
Press [GROUP NAME] to specify the search string.
Groups that contain the search string in the [GROUP NAME] box will be found.
55
Press [SEARCH].
The touch panel displays the found groups. Press a group and press [OK] to edit the
group information.
For instructions on editing groups, see the following page:

P.45 Editing groups
Confirming the members of a group

You can confirm the contacts that are registered in a group.

56

Press [GROUP].
Press [CONTENTS] of the group whose members you want to confirm.
The contacts registered in the group are displayed.
57
Checking E-mail
This function allows you to check for new e-mails (Internet Faxes) on the POP3 server.
It is necessary to configure the POP3 server using TopAccess to perform this function. For instructions on how to
configure the POP3 server, refer to the TopAccess Guide.
The equipment also automatically checks for new e-mails on the POP3 server.
Press [CHECK E-MAIL] in the USER menu.
The equipment begins communicating with the POP3 server. If a new e-mail is on the POP3 server, the equipment
automatically prints the e-mail data after retrieving it from the POP3 server.

58
Checking E-mail
Setting BIP Printing

[BIP PRINTING] is available only when the Bluetooth Module (optional) is installed. For instructions on how to set the BIP
printing, refer to the GN-2010 Operators Manual for Bluetooth Module.
Setting BIP Printing
59
SETTING ITEMS (ADMIN)
2.
Entering Admin Menu ............................................................................................................ 63

Setting General Functions..................................................................................................... 65
Setting the device information ..............................................................................................................................65
Setting the notification ..........................................................................................................................................66
Changing the administrator password ..................................................................................................................68
Setting the date and time .....................................................................................................................................70
Setting the energy saver modes...........................................................................................................................72
Setting the calibration and registration display level ............................................................................................76
Setting the drawer set pop-up and paper jam recovery pop-up ...........................................................................77
Setting the status message ..................................................................................................................................78
Setting the calibration ...........................................................................................................................................79
Setting the registration .........................................................................................................................................84
Setting the panel calibration .................................................................................................................................85
Setting Network Functions.................................................................................................... 87

Setting the TCP/IP protocol (IPv4) .......................................................................................................................87
Setting the IPv6 protocol ......................................................................................................................................91
Setting the IPX/SPX protocol ...............................................................................................................................98
Setting the NetWare settings..............................................................................................................................100
Setting the SMB protocol....................................................................................................................................102
Setting the AppleTalk protocol............................................................................................................................104
Setting the HTTP network service ......................................................................................................................106
Setting the Ethernet speed.................................................................................................................................108
Setting the LDAP/SNMP network services and the filtering functions................................................................109
IPsec (IP security) setting................................................................................................................................... 111
Decrypting the user certificate ............................................................................................................................ 113
Network check .................................................................................................................................................... 115
Setting Copy Functions ....................................................................................................... 118

Setting Fax Functions.......................................................................................................... 120
Setting the discard and reduction print option for the RX print ...........................................................................120
Setting File Functions.......................................................................................................... 122

Setting E-mail Functions ..................................................................................................... 123
Setting Internet Fax Functions............................................................................................ 124
Setting Security Functions.................................................................................................. 125
Setting List/Report ............................................................................................................... 127
Printing Lists ........................................................................................................................ 132
Setting Printer/e-Filing Functions....................................................................................... 133
Wireless Settings and Bluetooth Settings......................................................................... 134

Change User Password....................................................................................................... 135
IEEE 802.1X Authentication Setting ................................................................................... 136
Setting IEEE802.1X authentication .................................................................................................................... 136
2 SETTING ITEMS (ADMIN)
Entering Admin Menu

When the administrator password has been set, you must enter the administrator password to enter the ADMIN menu in
the USER FUNCTIONS screen.
Press the [USER FUNCTIONS] button on the control panel to enter the USER
FUNCTIONS menu.
Press the [ADMIN] tab.
Press [PASSWORD].
The ADMINISTRATOR PASSWORD screen is displayed.
Enter the administrator password and press [OK].
The ADMIN menu is displayed.
If the administrator password has not been changed before, enter the default administrator password 123456.
If you enter incorrect passwords three times in a row, the equipment cannot be operated for 30 seconds.
Entering Admin Menu
63
Continue the administrative operation that you require.
P.65 Setting General Functions

P.87 Setting Network Functions
P.118 Setting Copy Functions
P.120 Setting Fax Functions
P.122 Setting File Functions
P.123 Setting E-mail Functions
P.124 Setting Internet Fax Functions
P.125 Setting Security Functions
P.127 Setting List/Report
P.132 Printing Lists
P.133 Setting Printer/e-Filing Functions
P.134 Wireless Settings and Bluetooth Settings
P.135 Change User Password
P.136 IEEE 802.1X Authentication Setting
y [WIRELESS SETTINGS] in the ADMIN menu is available only when the Wireless LAN Module (optional) is
installed. For instructions on how to use the WIRELESS SETTINGS, refer to the GN-1050 Operators
Manual for Wireless LAN Module.
y [Bluetooth SETTINGS] in the ADMIN menu is available only when the Bluetooth Module (optional) is
installed. For instructions on how to use the Bluetooth SETTINGS, refer to the GN-2010 Operators
Manual for Bluetooth Module.
64
Entering Admin Menu

Setting the device information
You can set the device information of this equipment. These items appear in the Device page of TopAccess, a web-based
device management utility.
Press [GENERAL] in the ADMIN menu.
To display the ADMIN menu, see the following page:

P.63 Entering Admin Menu
Press [DEVICE INFORMATION].
The DEVICE INFORMATION screen is displayed.
65
Specify the following items as required and press [OK].
[LOCATION] Press this button to enter the location of this device.

[SERVICE PHONE NUMBER] Press this button to enter the service call number.
[CONTACT INFORMATION] Press this button to enter the name of the service technician.
[ADMIN. MESSAGE] Press this button to enter an administration message for users.
When you press each button, the on-screen keyboard is displayed. Enter a value using the keyboard and digital
keys, and press [OK] to set the entry. To enter [SERVICE PHONE NUMBER], enter the number using only the
digital keys.
Setting the notification

You can set the notification mail to send a notification message when specified events occur on the equipment, such as
toner empty, paper empty, and serviceman call.
You can specify up to three e-mail addresses for the destination of the notification message.
You can specify events that you want to be notified about using the TopAccess web utility. For instructions on how to
specify events for notification, refer to the TopAccess Guide.
To enable this function, there must be a SMTP server in your network. In addition, the settings to enable the Internet
Fax transmission on this equipment must be configured correctly.

66

2.SETTING ITEMS (ADMIN)
Press [NOTIFICATION].
The NOTIFICATION screen is displayed.
Press [E-MAIL].
Enter the e-mail address using the keyboard and digital keys and press [OK].
You can specify up to three e-mail addresses to which notification messages will be sent, as required. When
you enable notification, you must enter at least one e-mail address.
67
Press [ON] for the e-mail address to receive notification and press [OK].
To disable notification for an e-mail address, press [OFF].
[ON] is available after you enter an e-mail address.
Changing the administrator password

You can change the administrator password.

Press [PASSWORD SETUP].
The PASSWORD SETUP screen is displayed.
68

Press [OLD PASSWORD].
Enter the current administrator password and press [OK].
The input password appears as asterisks (*).
If the administrator password is being changed for the first time, enter 123456 in the [OLD PASSWORD] box.
Set new password and complete the setting.

1) Press [NEW PASSWORD] to enter new password.
2) Press [RETYPE NEW PASSWORD] to enter the new password again.
3) Press [OK].
When you press [NEW PASSWORD] and [RETYPE NEW PASSWORD], the on-screen keyboard is displayed.
Enter the value using the keyboard and digital keys, and press [OK] to set the entry.
You can enter 6 - 10 alphanumeric characters for the administrators password. Symbols cannot be used.
69
Setting the date and time

The clock built in to this equipment can be set by entering the date and time using the digital keys.

Press [CLOCK].
The CLOCK menu is displayed.
Press [DATE/TIME].
y If you want to change the date format only, skip to step 5.

y When you press [DATE/TIME], the DATE/TIME screen is displayed.
70

Highlight the section that you want to edit using the arrow buttons, enter the number
using the digital keys, and press [OK].
You will be returned to the CLOCK menu.
The DAY section describes the days of week using numbers. The numbers corresponding to the days of the
week are as follows:
1: Sun, 2: Mon, 3:Tue, 4: Wed, 5: Thu, 6: Fri, 7: Sat
Press [DATE FORMAT].
The DATE FORMAT screen is displayed.
Press the desired date format button.
71
Setting the energy saver modes

The following energy saver modes are available in this menu.
y Weekly timer
Using the built-in weekly timer, you can have the equipment automatically turned ON and OFF at specified times. For
instance, you can set the timer for the starting time and closing time of your office so that the copier will automatically
turn itself ON and OFF at those specified times.
You can turn on the power by simply pressing the [START] button on the control panel when the device is in the sleep
mode by the weekly timer.
When the power switch is turned off, the weekly timer does not work.
y Auto power save mode
This function allows the equipment to automatically go into the energy saving mode if it is left inactive for a certain
period of time.
y Sleep mode
This function puts the equipment into the sleep mode (unnecessary electricity is cut off at standby) if it is left inactive
for a certain period of time.
Neither [AUTO POWER SAVE] nor [SLEEP MODE] is available for the European version.

Press [ENERGY SAVER].
The ENERGY SAVER menu is displayed.
72

P.73 Setting the weekly timer

P.74 Setting the auto power save mode
P.75 Setting the sleep mode
Setting the weekly timer
Press [WEEKLY TIMER].
The TIMER screen is displayed.
Check the settings on the display. If corrections are required, press [CHANGE].
If no corrections are required, press [OK] and complete the operation.
73
Make settings for the weekly timer.

1) Press the desired day of the week button.
2) Press [ON] to enter the time the device wakes up from the sleep mode.
Use the arrow buttons to move the cursor and enter Hour and Minute.
3) Press [OFF] to enter the time to put the device into the sleep mode.
Use the arrow buttons to move the cursor and enter Hour and Minute.
4) Press [OK] to save the settings.
y If you want to clear an entered time, press the [CLEAR] button on the control panel.
y If you want to put the equipment into the sleep mode during the entire day, enter the same time in both the
[ON] and [OFF] boxes.
Example) When you enter 0:00 in both the [ON] and [OFF] boxes for [SUN],
the equipment automatically goes into the sleep mode at the [OFF] time specified for [SAT]. The sleep mode
is kept until the [ON] time specified for [MON] comes.
y If you do not want to put the equipment into the sleep mode during the entire day, make settings for the
desired day of the week button as follows:
[ON]: 0:00 / [OFF]: 24:00
The equipment does not go into the sleep mode during the entire day, which is activated by the weekly timer
function. However, the equipment automatically goes into the sleep mode according to the time value set for
[SLEEP MODE] (or the preset time value for activating the sleep mode), if it is left inactive for a certain
period of time.
Setting the auto power save mode
Press [AUTO POWER SAVE].
The AUTO POWER SAVE screen is displayed.
74

Press the desired period of time (in minutes) that this equipment will wait before the
auto power save mode is activated.
The auto power save mode setting is completed.
Setting the sleep mode
Press [SLEEP MODE].
The SLEEP MODE screen is displayed.
Press the desired period of time (in minutes) that this equipment should wait before the
sleep mode is activated.
The sleep mode setting is completed.
75
Setting the calibration and registration display level

You can set whether this equipment will use the calibration and registration settings that are operated by a user or
administrator.
When you select the admin mode for the calibration display level, [CALIBRATION] under the USER menu disappears.
When you select the user mode for the calibration display level, [CALIBRATION] under the ADMIN menu disappears.
When you select the admin mode for the registration display level, [REGISTRATION] under the USER menu disappears.
When you select the user mode for the registration display level, [REGISTRATION] under the ADMIN menu disappears.
Press [GENERAL] in the Admin menu.

Press [DISPLAY LEVEL].
The DISPLAY LEVEL screen is displayed.
Press [USER] or [ADMIN] for each option and press [OK].
The display level setting is completed.
76

Setting the drawer set pop-up and paper jam recovery pop-up
You can set whether or not to display a message to ask users to change the paper size setting every time you open the
drawer.
You can also set whether or not to display a message to ask users to continue the copying or printing after fixing a paper
jam.

Press [POP-UP].
The POP-UP screen is displayed.
Press [ENABLE] or [DISABLE] for each option and press [OK].
DRAWER SET When this option is enabled, this equipment displays a message asking users to change the
paper size setting every time they open the drawer.
PAPER JAM RECOVERY When this option is enabled, this equipment displays a message asking users to
continue copying or printing when the paper jam is fixed. When this option is disabled, copying or printing will be
continued automatically when the paper jam is fixed.
77
Setting the status message

This function allows the equipment to display the status message at the bottom of the touch panel to notify you of the
occurrence of specified events, such as when paper has run out and toner is low.

Press [STATUS MESSAGE].
The STATUS MESSAGE menu is displayed.
78

Press [ON] or [OFF] for each status message and press [OK].
TONER NEAR EMPTY MESSAGE When you select [ON], this message will be displayed on the touch panel
when toner is low in each toner cartridge.
PAPER EMPTY MESSAGE When you select [ON], this message will be displayed on the touch panel if there is
no paper in a drawer.
LEFT DRAWER (LCF) PAPER EMPTY MESSAGE When you select [ON], this message will be displayed on
the touch panel if the left tray of the Tandem Large Capacity Feeder is out of paper.
The status message LEFT DRAWER (LCF) PAPER EMPTY MESSAGE applies only to e-STUDIO5520C/
6520C/6530C with the Tandem Large Capacity Feeder installed.
Setting the calibration

This function allows the machine to automatically calibrate the color gradation for copy jobs or print jobs when the color
cannot be adjusted accurately because the shading or the hue of the image has deviated.
y The calibration setting in the ADMIN menu can be performed only when an administrator has set the calibration
display level to [ADMIN].
y Place LT or A4 paper (recommended paper) in the drawer before starting the calibration. If any other paper is used,
calibration may not be performed properly.
y If the glass is dirty or any foreign objects are stuck to the glass, the calibration may not be performed properly.
Keep the glass clean.
y Never raise the original cover or the Reversing Automatic Document Feeder, or open the front cover while the
calibration is in progress. If this does happen, the calibration cannot be finished properly.
y Interrupt copying is not available during the calibration.
y If the color often deviates, call your service technician.
Place the paper to be used for the calibration in the drawer.

Place paper in the large capacity feeder if it is installed. If it is not, place paper in the uppermost drawer in which A4
or LT has been registered.
79

Press [CALIBRATION].
The CALIBRATION menu is displayed.
P.81 Setting the copy calibration

P.82 Setting the print calibration
For e-STUDIO 5520C/6520C/6530C, [600dpi PRINT] and [1200dpi PRINT] are provided instead of [PRINT].
80

Setting the copy calibration
Press [COPY].
Press [DEFAULT] to set the default calibration setting, or [CALIBRATION] to adjust the
calibration setting.
y When you press [DEFAULT], the system maintains the default calibration setting and returns to the previous
screen.
y When you press [CALIBRATION], a chart is printed out and the calibration guide illustration is displayed on the
touch panel.
Place the printed chart face down on the glass with the bottom toward you and the top
left aligned against the original scale on the left side, so that two black rectangular
marks are placed on the left side.
Press the [START] button on the control panel.

When the calibration setting is completed, the GENERAL menu will be displayed.
If the chart is not properly placed, the message Set chart correctly is displayed on the touch panel. In this
case, return to step 3 and realign the chart.
81
Setting the print calibration
Press the following buttons as required.

Press [PRINT].
Press either of the following buttons.

y [600dpi PRINT]
Press this button to calibrate for the 600 dpi print jobs.
y [1200dpi PRINT]
Press this button to calibrate for the 1200 dpi print jobs.
Press [DEFAULT] to set the default calibration setting, or [CALIBRATION] to adjust the
calibration setting.
y When you press [DEFAULT], the system maintains the default calibration setting and returns to the previous
screen.
y When you press [CALIBRATION], a chart is printed out and the calibration guide illustration is displayed on the
touch panel.
82

Place the printed chart face down on the glass with the bottom toward you and the top
left aligned against the original scale on the left side, so that two black rectangular
marks are placed on the left side.
Press the [START] button on the control panel.

After scanning the printed chart, the following message is displayed:
[Apply Calibration Setting?]
If the chart is not properly placed, the message Set chart correctly is displayed on the touch panel. In this
case, return to step 3 and realign the chart.
Press [YES] to apply the calibration setting, or [NO] to cancel it.
83
Setting the registration

When color misregistration occurs, this function allows you to align the position of each color.
The registration setting in the ADMIN menu can be performed only when an administrator has set the registration
display level to [ADMIN].

Press [REGISTRATION].
The REGISTRATION menu is displayed.
Press [YES] to start the registration.
The registration process begins.
84

Setting the panel calibration

When the buttons on the touch panel are hardly to be pressed, this function allows you to adjust the position of each
button.

Press [PANEL CALIBRATION].
The panel calibration operation screen (1) is displayed.
Touch the center of the + mark with a stylus, referring to the message displayed on the
touch panel.
The panel calibration operation screen (2) is displayed.
85
Touch the center of the + mark with a stylus, referring to the message displayed on the
touch panel.
When the panel calibration operation is completed, the GENERAL menu will be displayed.
While the panel calibration operation is being performed, any other operations on the touch panel cannot be
performed. If you open the front cover of the equipment during the panel calibration operation and instructions
to replace toner cartridges are displayed, close the front cover, and complete the panel calibration operation,
and then replace toner cartridges.
86
Setting Network Functions

Setting the TCP/IP protocol (IPv4)
You can set the TCP/IP protocol that is commonly used for most network system. It is recommended that the TCP/IP
protocol be configured because TopAccess, the web-based device management utility, and e-Filing, the web-based utility
that allows you to manage files in e-Filing, will be available with the TCP/IP protocol. In addition, other network features of
this equipment use the TCP/IP protocol.
In the TCP/IP menu, you can select the addressing mode, and assign the IP address, subnet mask and default gateway (if
manually assigned).
How the TCP/IP protocol is configured depends on the network configuration of your network.
y When you assign the TCP/IP using the Auto-IP addressing or DHCP server:
If you do not know how the TCP/IP settings should be assigned, you can select the dynamic addressing mode. When
the dynamic addressing mode is selected, this equipment will obtain the IP address, subnet mask, default gateway,
primary WINS server address, secondary WINS server address, POP3 server address, and SMTP server address
from the DHCP server if the network supports the DHCP. If the network does not support the DHCP, this equipment will
assign the appropriate IP address using the auto-IP addressing. However, the auto-IP addressing may not work
properly when the router is placed in the network.
y When you assign the TCP/IP using only the DHCP server:
If your local area network has been configured with the DHCP server and you do not want to enable the auto-IP
addressing, you can select the no auto-IP addressing mode. When the no auto-IP addressing mode is selected, the IP
address, subnet mask, default gateway, primary WINS server address, secondary WINS server address, POP3 server
address, and SMTP server address will be automatically obtained from the DHCP server, and the auto-IP addressing
will be disabled. To enable the DHCP addressing only, please configure the TCP/IP settings as described in the
following procedure.
y When you connect to a local area network where static IP addresses are used:
If your local area network has been configured with a static IP address, you must assign the specific IP address,
subnet mask, and default gateway as required.
Press [NETWORK] in the ADMIN menu.
The NETWORK menu is displayed.

87
Press [IPv4].
The IPv4 screen is displayed.
P.88 Setting the TCP/IP for auto-IP and DHCP server

P.89 Setting the TCP/IP for DHCP server only
P.90 Setting the TCP/IP for static IP address
Setting the TCP/IP for auto-IP and DHCP server
Press [DYNAMIC] in the ADDRESS MODE option and press [OK].
You will be returned to the NETWORK menu.
88

Continue to another network setting if required, then press [APPLY NOW].
The NETWORK INITIALIZING message is displayed and this equipment starts initializing the network interface
card to apply the changes.
Setting the TCP/IP for DHCP server only
Press [NO AUTO IP] in the ADDRESS MODE option and press [OK].
89
Setting the TCP/IP for static IP address
Press [STATIC] in the ADDRESS MODE option.
Specify the following items as required and complete the setting.

1) Press [IP ADDRESS] and enter the IP address of this device using the digital keys.
2) Enter the subnet mask and default gateway as required.
3) Press [OK].
90

Setting the IPv6 protocol

You can set the IPv6 protocol on this equipment.
This IPv6 menu allows you to enable or disable the IPv6 protocol used on this equipment. In this menu, you can also set
IPv6 configurations, such as the IPv6 address, by selecting the address mode.
How the IPv6 address is obtained depends on the address mode you select.
y When you select the manual mode:
You assign the IPv6 address, prefix and default gateway manually. In this mode, you can assign one IPv6 address to
this equipment.
P.91 Setting the IPv6 protocol manually
y When you select the stateless mode:
This equipment can obtain multiple IPv6 addresses from the DHCPv6 server and routers automatically. In this mode,
up to 9 IPv6 addresses can be registered on this equipment.
P.94 Setting the IPv6 protocol automatically (in a stateless network environment)
Up to 7 IPv6 addresses can be obtained from routers. One IPv6 address can be obtained from the DHCPv6 server.
One link local address is also generated automatically.
y When you select the stateful mode:
You can automatically obtain the IPv6 address from the DHCPv6 server. In this mode, you can register one IPv6
address to this equipment.
P.96 Setting the IPv6 protocol automatically (in a stateful network environment)
If you change IPv6 PROTOCOL from [ENABLE] to [DISABLE] when the INTERNET PROTOCOL VERSION option
for SMB is IPv6, it is necessary to reboot this equipment to apply the change. When the message Reboot the
machine is displayed on the touch panel, power OFF the equipment then power it back ON by using the [POWER]
button on the control panel.
Setting the IPv6 protocol manually

91
Press [IPv6].
Specify the following items as required and press
IPv6 PROTOCOL Press [ENABLE] to enable the IPv6 protocol, or [DISABLE] to disable the IPV6 protocol.
LLMNR Press [ENABLE] to enable the LLMNR (Linklocal Multicast Name Resolution) protocol, or [DISABLE] to
disable the LLMNR protocol.
ADDRESS MODE Select [MANUAL].
Link Local Address The unique address used for the IPv6 is displayed.
y The link local address cannot be connected to another routed IPv6 network.
y [ENABLE] and [DISABLE] for the LLMNR protocol are available when you select [ENABLE] for the IPv6
protocol.
92

DHCP (OPTIONS) Select whether or not the optional information (IPv6 address for the DNS server, etc.), except
the IPv6 address for this equipment, which is issued from the DHCPv6 server, is used on this equipment. Press
[ENABLE] to use the information, or [DISABLE] not to use it.
[IP ADDRESS] Press this button to assign the IPv6 address for this equipment.
[PREFIX] Press this button to assign the prefix for the IPv6 address.
[GATEWAY] Press this button to assign the default gateway.
In MANUAL mode, you cannot select the DHCP (IP Address) option.
When you press [IP ADDRESS], [PREFIX] or [GATEWAY], the on-screen keyboard is displayed. Enter the
value using the keyboard and digital keys, and press [OK] to set the entry.
If Duplicate Address Detection (DAD) detects duplicate addresses, the message IPv6 ADDRESS CONFLICT
is displayed on the touch panel.
93
Setting the IPv6 protocol automatically (in a stateless network environment)

Press [IPv6].
ADDRESS MODE Select [STATELESS].
protocol.
94

Specify the following items as required.
KEEP CONFIGURATION Select the method for handling IPv6 address data when a new IPv6 address is
provided from the same router providing the current IPv6 address to this equipment. Press [ENABLE] to retain the
current IPv6 address data and add the new IPv6 address to this equipment. Press [DISABLE] to overwrite the
current IPv6 address data with the new IPv6 address.
DHCP (IP Address) Press [ENABLE] to use the IPv6 address issued from the DHCPv6 server in a stateless
network environment, or [DISABLE] not to use it.
DHCP (OPTIONS) Press [ENABLE] to use the optional information (IPv6 address for the DNS server, etc.)
issued from the DHCPv6 server in a stateless network environment, or [DISABLE] not to use it.
When you select [ENABLE] for the DHCP (IP Address) option, [ENABLE] is automatically set for the DHCP
(OPTIONS) option.
Press
IPv6 addresses obtained from routers are displayed.
Up to 7 IPv6 addresses can be retained.
When this equipment receives a router advertisement (RA) from a router with an M flag configuration of 0, the
DHCPv6 function is disabled. If you change a router advertisement (RA) M flag configuration from 0 to 1,
reboot this equipment by using the [POWER] button on the control panel to enable the DHCPv6 function.
Press [OK].
95
Setting the IPv6 protocol automatically (in a stateful network environment)

Press [IPv6].
96

ADDRESS MODE Select [STATEFUL].
protocol.
DHCP (IP Address) Select whether or not the IPv6 address issued by the DHCPv6 server is used for this
equipment. Press [ENABLE] to use the address, or [DISABLE] not to use it.
DHCP (OPTIONS) Select whether or not the optional information (IPv6 address for the DNS server, etc.), except
the IPv6 address for this equipment, which is issued from the DHCPv6 server, is used on this equipment. Press
[ENABLE] to use the information, or [DISABLE] not to use it.
y In Stateful mode, you cannot assign [IP ADDRESS], [PREFIX] or [GATEWAY] manually.
y Either the DHCP (IP Address) option or the DHCP (OPTIONS) option must be in [ENABLE].
97
Setting the IPX/SPX protocol

You can set the IPX/SPX protocol on this equipment. The IPX/SPX protocol is usually used to communicate with the
NetWare file server through the network.

Press [IPX/SPX].
The IPX/SPX screen is displayed.
98

ENABLE IPX/SPX Press [ENABLE] to enable the IPX/SPX protocol, or [DISABLE] to disable the IPX/SPX
protocol.
FRAME TYPE Press [AUTO] to automatically detect the appropriate frame type, or press another frame type
button. If you do not know the frame type that must be used, select [AUTO].
99
Setting the NetWare settings

You can set the NetWare network mode and the NetWare configuration to be connected.
This option must be set when you use the NetWare file server for Novell printing.

Press [NETWARE].
The NETWARE screen is displayed.
100

ENABLE BINDERY Press [ENABLE] to enable communicating with the NetWare file server in bindery mode, or
[DISABLE] to disable bindery mode.
ENABLE NDS Press [ENABLE] to enable communicating with the NetWare file server in NDS mode, or
[DISABLE] to disable NDS mode.
[CONTEXT] Press this button to enter the NDS context in which the NetWare print server for this equipment is
located. This must be entered when you connect the NetWare file server in NDS mode.
[TREE] Press this button to enter the NDS tree. This must be entered when you connect the NetWare file server
in NDS mode.
[SEARCH ROOT] Press this button to enter the NetWare file server name. It is recommended that this be
entered when you connect the NetWare file server in bindery mode.
y When you press [CONTEXT], [TREE] and [SEARCH ROOT], the on-screen keyboard is displayed. Enter
the value using the keyboard and digital keys, and press [OK] to set the entry.
y You can enable both bindery and NDS modes at the same time.
101
Setting the SMB protocol

When you want to make this equipment visible in the Windows network, you must enable the SMB protocol and enter the
NetBIOS name and workgroup to specify the device name of this equipment and workgroup where it will be visible.
If your network uses the WINS server to allow SMB communications across segments, you must specify the WINS server
address so that this equipment will be visible from the different segments.
This must be enabled for SMB printing, Save as file to the network folder using SMB, and sharing the FILE_SHARE
folder (that is the local folder of this equipment) in the network.

Press [SMB].
The SMB screen is displayed.
102

SMB PROTOCOL Select whether the SMB protocol is enabled or disabled.

When you want to enable the SMB protocol to enable saving as a file to network folder using SMB and sharing the
FILE_SHARE folder of this equipment, but not to enable the SMB printing, press [DISABLE PRINT SHARE].
When you want to enable the SMB protocol to enable the SMB printing, but not to enable saving as a file to
network folder using SMB and sharing the FILE_SHARE folder of this equipment, press [DISABLE FILE SHARE].
[NetBIOS NAME] Press this button to enter the Windows computer name of this device if this device is
connected to the Windows network. This must be specified when you want to enable SMB printing.
LOGON This displays the Windows network logon environment. workgroup will be displayed if this equipment
is logged on to the workgroup network and domain will be displayed if this equipment is logged on to the domain
network. This option can be specified only from TopAccess. For details, refer to the TopAccess Guide.
[WINS PRIMARY] Press this button and enter the IP address of the primary WINS server using the digital keys
if required.
[WINS SECONDARY] Press this button and enter the IP address of the secondary WINS server using the
digital keys if required.
INTERNET PROTOCOL VERSION Press [IPv4] to enable the IPv4 protocol. In this case, use of the IPv6
protocol is not available. Press [IPv6] to enable the IPv6 protocol. In this case, use of the IPv4 protocol is not
available.
y When you press [NetBIOS NAME], the on-screen keyboard is displayed. Enter the value using the
keyboard and digital keys, and press [OK] to set the entry.
y [IPv4] and [IPv6] for the INTERNET PROTOCOL VERSION option are available when you enable the IPv6
protocol.
P.91 Setting the IPv6 protocol
y When you select [DISABLE] or [DISABLE FILE SHARE], the Save as File to MFP Local function will be
disabled.
y If this equipment is configured to log on to the domain in the SMB Session of TopAccess administrator mode
but workgroup is displayed, logging on to the domain network has failed. In that case, confirm that the
Windows Server and the SMB Session settings are correct.
y When you set Domain for the Logon setting in the SMB Session of TopAccess administrator mode, this
equipment will log on to the domain network after turning ON the power or changing the network settings
and pressing [APPLY NOW].
y You can enter only alphanumeric characters and - (hyphenation) for NetBIOS names. If you use any other
characters, a warning message will be displayed.
y Do not enter an IP address that starts with 0 (i.e. 0.10.10.10), 127 (i.e. 127.10.10.10), or 224 (i.e.
224.10.10.10). If you enter such an address, the equipment cannot communicate with the WINS server.
y If you enter 0.0.0.0 for [WINS PRIMARY] and [WINS SECONDARY], this equipment will not use the WINS
server.
y When [DYNAMIC] or [NO AUTO IP] is selected for the ADDRESS MODE option in the TCP/IP setting, this
equipment can obtain the IP address for [WINS PRIMARY] and [WINS SECONDARY] from the DHCP
server.
y When selecting [IPv6] for the INTERNET PROTOCOL VERSION option, you cannot set [WINS PRIMARY]
and [WINS SECONDARY].
y If you change the INTERNET PROTOCOL VERSION option from [IPv4] to [IPv6] or vice versa, it is
necessary to reboot the equipment to apply the change. When the message Reboot the machine is
displayed on the touch panel, power OFF the equipment and then power it back ON by using the [POWER]
button on the control panel.
103
Setting the AppleTalk protocol

The AppleTalk protocol must be enabled and properly configured to enable AppleTalk printing with a Macintosh computer.

Press [APPLETALK].
The APPLETALK screen is displayed.
104

ENABLE APPLETALK Press [ENABLE] to enable the AppleTalk, or [DISABLE] to disable the AppleTalk.
[DEVICE NAME] Press this button to enter the AppleTalk name of this equipment.
[DESIRED ZONE] Press this button to enter the AppleTalk zone name this equipment has joined. If your
AppleTalk network has not been configured with a zone, you do not have to enter the zone name.
When you press [DEVICE NAME] and [DESIRED ZONE], the on-screen keyboard is displayed. Enter a value
using the keyboard and digital keys, and press [OK] to set the entry.
105
Setting the HTTP network service

This function allows you to enable or disable the HTTP network server service that provides the web-based utility on this
equipment, such as TopAccess and the e-Filing web utility.

Press [HTTP].
The HTTP screen is displayed.
106

ENABLE HTTP SERVER Press [ENABLE] to enable the HTTP network server service, or [DISABLE] to disable
the HTTP network server service. This option must be enabled for TopAccess and the e-Filing web utility.
[PRIMARY PORT NUMBER] Press this button to enter the primary port number to be used for HTTP access
from the other client. It is recommended that you use the default port number 80 if you are not sure about
changing this port number.
[SECONDARY PORT NUMBER] Press this button to enter the secondary port number to be used to access
TopAccess and the e-Filing web utility. It is recommended that you use the default port number 8080 if you are not
sure about changing this port number.
ENABLE SSL Press [ENABLE] to enable the SSL for accessing TopAccess and the e-Filing web utility, or
[DISABLE] to disable the SSL for accessing TopAccess and the e-Filing web utility. When this option is enabled,
the data transferred between the equipment and client computers will be encrypted using a private key when
operating TopAccess and the e-Filing web utility.
To enable SSL, you must create a self-signed certificate in the equipment or import a server certificate using
TopAccess. If the self-signed certificate is not created or the server certificate is not imported, SSL cannot be
enabled.
107
Setting the Ethernet speed

This function allows you to specify the ethernet speed.

Press [ETHERNET].
The ETHERNET screen is displayed.
Press [AUTO] to automatically detect the appropriate ethernet speed, or press another
ethernet speed button, then press [OK].
y When you select a specific ethernet speed, you must select the same ethernet speed as set in the
connected network. If you do not know the ethernet speed that must be used, select [AUTO].
y If the network is not stable, power OFF the equipment and then power it back ON.
108

Setting the LDAP/SNMP network services and the filtering functions

This function allows this equipment to access the LDAP directory service. The equipment can search the LDAP server for
contacts to specify recipients for Internet Faxes, fax transmissions, and Scan to E-mail jobs.
In this setting menu, you can also change the SNMP read community name, and change the IP/MAC address filtering
functions from [ENABLE] to [DISABLE] or vice versa.
If the LDAP network service is enabled, you can register the LDAP directory service, and then this equipment can
search for contacts in the LDAP server. To add the LDAP directory service, you must operate using TopAccess. For
more information about registering the directory service, refer to the TopAccess Guide.
When the LDAP network service is disabled, it is not possible to use the users e-mail address as From Address from
the LDAP server during the User Authentication for Scan to Email.

109
Press [OTHER].
The OTHER screen is displayed.
ENABLE LDAP Press [ENABLE] to enable the LDAP network service, or [DISABLE] to disable it.
[SNMP READ COMMUNITY] Press this button to enter the SNMP read community name for SNMP access if
required.
ENABLE IP FILTERING Press [ENABLE] to enable the IP filtering function, or [DISABLE] to disable it.
ENABLE MAC ADDRESS FILTERING Press [ENABLE] to enable the MAC address filtering function, or
[DISABLE] to disable it.
When you press [SNMP READ COMMUNITY], the on-screen keyboard is displayed. Enter a value using the
y If you specify a community name other than public for the read community, the applications that use MIB
(TopAccessDocMon, TWAIN driver, File Downloader, and AddressBook Viewer) will be unavailable. The
SNMP communication of the printer driver also will be unavailable, and obtaining the configurations,
confirming the department code, and obtaining the available boxes in e-Filing will be disabled.
y When the Read Community option is blank, SNMP communications between the SNMP browser of the
client PC and this equipment will be disabled.
110

IPsec (IP security) setting

When the IPSec Enabler (optional) is adopted, the encrypted communication is enabled using the IPsec (IP Security
Protocol).
The following operations are available in this menu.
y Viewing the IPsec policy name currently applied
y Enabling / Disabling IPsec communication
y Flushing IPsec session
Settings required for IPsec such as entry of IPsec policies can be performed using TopAccess. For details, refer to the
TopAccess Guide.
[IPsec] is available only when the IPSec Enabler (optional) is adopted.

111
Press [IPsec].
The IP SECURITY screen is displayed.
POLICY NAME IPsec policy name currently applied is displayed.

[ENABLE] Press this button to enable IPsec communication.
[DISABLE] Press this button to disable IPsec communication.
[FLUSH CONNECTIONS] Press this button to manually clear (flush) the current IPsec session, for starting a
new session.
[FACTORY DEFAULT] Press this button to reset the IPsec settings back to the factory defaults.
When you press [FLUSH CONNECTION], a message asking you to perform the operation is displayed.
112

Decrypting the user certificate

When you import the following certificates using the Security Service option in TopAccess, this function allows you to enter
the password to decrypt a certificate.
y Server certificate used for SSL
y Certificate for IPsec
y Certificate for IEEE802.1X
This function must be performed after importing the required certificate using TopAccess. For more information about
importing the certificate, refer to the TopAccess Guide.

Press [USER CERTIFICATE].
The USER CERTIFICATE screen is displayed.
113
Press the desired certificate button ([Server Protocol], [IPsec] or [802.1X]) and press
[PASSWORD].
Enter the password for the certificate using the keyboard and digital keys and press
[OK].
The input password appears as asterisks (*).
Press [OK].
Pressing [OK] returns you to the ADMIN menu and displays NETWORK INITIALIZING. This equipment starts
initializing the network interface card to apply the changes.
114

Network check
Two functions are available in the Network Check menu.
You can use the ping function to check the connection status between this equipment and the servers on the network. You
can also use the traceroute function to view and check the network path of the desired server.

Press [NETWORK CHECK].
The NETWORK CHECK screen is displayed.
115
Select the server you want to check and press [PING] or [TRACEROUTE].
The check result is displayed.

y When the ping function is performed, the check result IP address 128 (TTL: Time to live) fixed OK/NG is
displayed.
y When the traceroute function is performed, the check result IP address 1 to 128 (TTL: Time to live) OK/NG is
displayed.
When the ping/traceroute command can reach a server, the IP address is displayed for the check result for the
server. If the command cannot reach it for some reason, the host name is displayed instead of the IP address.
There are two ways to select the server you want to check.
To select the desired server from the server list displayed on the touch panel:
Checkable servers and supported protocols are as follows.
- Secondary DNS server (IPv4/IPv6)
- Primary DNS server (IPv4/IPv6)
- Primary WINS server (IPv4)
- Secondary WINS server (IPv4)
- SMTP server (IPv4/IPv6)
- POP3 server (IPv4/IPv6)
- Primary SNTP server (IPv4/IPv6)
116

Secondary SNTP server (IPv4/IPv6)

LDAP server 1
LDAP server 2
LDAP server 3
LDAP server 4
LDAP server 5
Remote server 1
Remote server 2
To designate the desired server manually:

Enter the server name, IPv4 address, or IPv6 address manually.
When you press the Manual Input column, the on-screen keyboard is displayed. Enter the value using the
When you enter a WINS name for the network path of the remote server 1 / 2 in TopAccess Save as file
Setting, the network check function cannot be performed with those servers selected from the server list. In
this case, designate the IP address of the remote server 1 / 2 manually to perform the network check function.
Press [RETURN].
117

You can change the system behaviors for the copy operation, such as maximum number of copies, auto 2-sided mode,
and the sort mode priority.
Press [COPY] in the ADMIN menu.
The COPY screen is displayed.

Specify following items as required and press
MAXIMUM COPIES Press the number button that indicates the maximum number of copies to be allowed.
AUTO 2-SIDE MODE Press the button of the 2-Sided mode that initially applies to copy settings when originals
are placed in the Automatic Document Feeder.
y [OFF] When this button is selected, the initial setting of the 2-Sided mode will be [1 -> 1 SIMPLEX] when
originals are placed in the Automatic Document Feeder.
y [1->2] When this button is selected, the initial setting of the 2-Sided mode will be [1 -> 2 DUPLEX] when
y [2->2] When this button is selected, the initial setting of the 2-Sided mode will be [2 -> 2 DUPLEX] when
y [USER] When this button is selected, the screen to select the 2-Sided mode will be displayed when originals
are placed in the Automatic Document Feeder.
SORT MODE PRIORITY Select the default sort mode that is applied for copy jobs. If [STAPLE] is selected, the
output is stapled on the upper left corner as the default. To staple copies, the optional finisher must be installed.
118

AUTOMATIC CHANGE OF PAPER SOURCE Selecting [ON] for this function allows the equipment to feed the
same size of paper from a different drawer even if the specified drawer from which paper is being fed is empty.
This function is always enabled when copy operations are performed using Automatic Paper Selection (APS). To
learn more about APS, refer to the Copying Guide.
PAPER OF DIFFERENT DIRECTION Selecting [ON] for this function allows the equipment to feed the same
size of paper that is set in a different direction if the drawer from which paper is being fed is empty.
Paper feeding when the drawer is out of paper during copying is as follows:
This is an example when the drawer for feeding paper is automatically changed while data is being copied on
A4-size paper.
Options
AUTOMATIC CHANGE OF
PAPER SOURCE
Paper Feeding
PAPER OF DIFFERENT
DIRECTION
ON
ON
Using Automatic Paper

Selection (APS)
Specifying the drawer

manually
A4 and A4-R paper are fed.
ON
OFF
A4 paper is fed.
A4 paper is fed.
OFF
ON
OFF
OFF
A4 paper is fed.
SUSPEND PRINTING IF STAPLER EMPTY When this is set to [ON], this equipment quit a job with stapling
when the stapler is empty. When this is set to [OFF], this equipment will continue the job without stapling.
DEFAULT MODE OF AUTO COLOR Press the default color mode for auto color.
119

If the FAX Unit and the 2nd Line for FAX Unit (both units are optional) are not installed, only the following option is
available: Discard and Reduction Print option for RX Print. For details on other fax options, refer to the GD-1250/
GD-1260/GD-1270 Operators Manual for FAX Unit.
If the FAX Unit (optional) is not installed, the setting items in this menu are applied to received Internet Fax jobs.
Setting the discard and reduction print option for the RX print
Set print settings for received Internet Fax originals that are to be printed.
Two print settings are available: discard print and reduction print.
Discard Print: ON, OFF
y ON (default setting):
When originals are up to 10mm larger than the printing area, the area of the originals that exceeds the paper printing
area is discarded.
y OFF: The received original is printed on two sheets of paper if its length exceeds the paper printing area.
* For DISCARD setting details, contact your service technician.
RX Reduction Print: ON, OFF
y ON (default setting):
If the received original is longer than the recording paper, it will be vertically reduced to 90% to fit on the recording
paper.
y OFF: The received original is printed on two sheets of paper if its length exceeds the paper printing area.
Press [FAX] in the ADMIN menu.
The FAX menu is displayed.

Press [RX PRINT].
The RX PRINT screen is displayed.
120

Press [ON] or [OFF] for each item as required and press [OK].
The registered items can be confirmed in the function list.

P.184 Function list (Administrator)
121
Setting File Functions

This function allows you to automatically delete files stored by the Scan to File operation. This function is used to
periodically delete stored files in local storage to maintain available hard disk space.
Press [FILE] in the ADMIN menu.
The MAINTENANCE menu is displayed.

Enable the storage maintenance function and complete the setting.

1) Press [ON].
2) Using the digital keys, enter the number of days that the system will preserve files before deleting them.
You can enter 1 to 99 days. To correct the value, press the [CLEAR] button on the control panel to delete the
input value and re-enter the number of days.
3) Press [OK].
When you press [OFF], press [OK] to complete the setting.
122
Setting File Functions
Setting E-mail Functions

This function allows you to set the following items.
y E-mail Message Properties
You can configure the following message properties of e-mail documents that will be sent by the Scan to E-mail
operation.
- FROM ADDRESS
- FROM NAME
- BODY
y Scan to E-mail Fragmentation
You can send a Scan to E-mail job split into the fragment size specified. This option can reduce transmission errors
caused by network traffic problems.
Press [E-MAIL].
The E-MAIL screen is displayed.

[FROM ADDRESS] Press this button to enter the e-mail address of this equipment.
[FROM NAME] Press this button to enter the identification name of this equipment.
[BODY] Press this button to enter the body message.
FRAGMENT MESSAGE SIZE (KB) Press the desired fragment size button. Press [NONE] to disable the
fragmentation.
To enable Scan to E-mail, you must enter an e-mail address in the [FROM ADDRESS] box.
When you press each button ([FROM ADDRESS], [FROM NAME] and [BODY]), the on-screen keyboard is
displayed. Enter a value using the keyboard and digital keys, and press [OK] to set the entry.
Setting E-mail Functions
123
Setting Internet Fax Functions

This function allows you to set the following items.
y Internet Fax Message Properties
You can configure the following message properties of Internet Faxes that will be sent by Internet Fax transmission.
- FROM ADDRESS
- FROM NAME
- BODY
y Internet Fax Fragmentation
You can send the Internet Fax job split into the fragment size specified. This option can reduce transmission errors
caused by network traffic problems.
y Internet Fax Body String Transmission
You can specify whether the body string will be transmitted or not.
Press [INTERNET FAX] in the ADMIN menu.
The INTERNET FAX screen is displayed.

[FROM ADDRESS] Press this button to enter the e-mail address of this equipment.
[FROM NAME] Press this button to enter the identification name of this equipment.
[BODY] Press this button to enter the body message.
FRAGMENT PAGE SIZE (KB) Press the desired fragment size button. Press [NONE] to disable the
fragmentation.
BODY STRING TRANSMISSION Press [ENABLE] to enable the body string transmission, or [DISABLE] to
disable the body string transmission.
To enable Internet Fax, you must enter an e-mail address to the [FROM ADDRESS] box.
When you press each button ([FROM ADDRESS], [FROM NAME] and [BODY]), the on-screen keyboard is
124
Setting Internet Fax Functions
Setting Security Functions

You can configure the default values for the encryption setting that is applied when data scanned on this equipment is
generated as a secure PDF file. You can also configure whether or not to use the forced encryption mode.
This setting is applied to operations for Scan to File or USB and Scan to E-mail.
Press [SECURITY] in the ADMIN menu.
The PDF SECURITY SETTINGS screen is displayed.

125
[USER PASSWORD] Press this button to enter a password required to open a secure PDF file. 12345 is the
default user password.
USE AUTHENTICATION CODE AS PASSWORD Press [ENABLE] to use a user authentication user name for
[USER PASSWORD] or [DISABLE] to use a password entered in the [USER PASSWORD] box.
[MASTER PASSWORD] Press this button to enter a password required to change the security setting of a
secure PDF file. 123456 is the default master password.
Encryption LevelSelect the encryption level for a secure PDF file.
y 128bit AESThe encryption level compatible for Acrobat7.0, PDF V1.6 is set.
y 128bit RC4The encryption level compatible for Acrobat5.0, PDF V1.4 is set.
y 40bit RC4The encryption level compatible for Acrobat3.0, PDF V1.1 is set.
AuthoritySelect the authority for a secure PDF file.
y PRINTPrinting is allowed.
y CHANGEChanging the document is allowed.
y EXTRACTContent Copying or Extraction is allowed.
y ACCESSIBILITYContent Extraction for Accessibility is allowed.
Forced Encryption Press [ENABLE] to allow this equipment to output only secure PDF files when data
scanned is generated and output. Press [DISABLE] to allow this equipment to output file formats (JPEG, TIFF, etc.)
other than the secure PDF.
When you press each button ([USER PASSWORD] and [MASTER PASSWORD]), the on-screen keyboard is
y Different passwords must be set for [USER PASSWORD] and [MASTER PASSWORD].
y Enter 1 to 32 alphanumeric characters for [USER PASSWORD] and [MASTER PASSWORD]. The input
password appears as asterisks (*).
y When the lock icon next to the [USER PASSWORD] box is highlighted, the user cannot change the
password.
y When the lock icon next to the [MASTER PASSWORD] box is highlighted, the user cannot change the
encryption level or authority.
y If 40bitRC4 is selected and either Extract or Accessibility is selected or deselected, both settings are
enabled or disabled accordingly.
y When you select [ENABLE] for the forced encryption mode, outputting file formats (JPEG, TIFF, etc.) other
than secure PDF is prohibited. Furthermore, the following Scan to File operations which cannot generate
secure PDFs will be unavailable.
- Copy & File
- Fax & File
- Internet Fax & File
- Network Fax & File
126
Setting List/Report
This menu allows you to make required settings for printing the following reports:
y Transmission / Reception journal
There are two types of journals available on this equipment. Journals can be printed either automatically or manually.
This function allows you to set auto-print for the journals, and the number of transactions appears in the journal list.
The old journals will be deleted and only the specified number of journals beginning with the newest one will be
printed. The most recent 100 journals can be exported as a file from TopAccess administrator mode.
y Communication report
The communication report allows you to print a report after every transmission. Reports can be printed automatically
only. This function allows you to select the conditions for printing communication reports for each transmission type
separately.
y Reception list
The reception list allows you to print a reception list after receiving a document to a mailbox on this equipment. This
function allows you to enable or disable printing a reception list for the following mailbox transmissions:
- Relay Station Receiving a relay transmission from an originator as a relay hub.
- Local Reserving a document to a mailbox within this equipment locally.
- Remote Reserving a document to a mailbox within this equipment remotely from another facsimile.
Press [LIST/REPORT] in the ADMIN menu.
The LIST/REPORT screen is displayed.

Press [REPORT SETTING].
The REPORT SETTING menu is displayed.
Setting List/Report
127
P.128 Setting the transmission / reception journal

P.129 Setting the communication report
P.130 Setting the reception list
Setting the transmission / reception journal
Press [JOURNAL].
The JOURNAL screen is displayed.
AUTO Press [ON] to enable printing the transmission and reception journals automatically. When you enable
this option, the transmission and reception journals will be printed when specified numbers of transmissions are
completed.
TX JOURNAL Press the number button to specify the number of transmissions that will be printed in a
transmission journal.
RX JOURNAL Press the number button to specify the number of receptions that will be printed in a reception
journal.
128
Setting List/Report

Setting the communication report
Press [COMM. REPORT].
The COMM. REPORT screen is displayed.
Specify the conditions for each transmission type and press
[OFF] Press this button to disable printing the communication report.

[ALWAYS] Press this button to print a communication report for every transmission.
[ON ERROR] Press this button to print a communication report only when an error occurs.
The DIRECT TX and POLLING settings are available only when the FAX Unit (optional) is installed.
When you press [ALWAYS] or [ON ERROR] for MEMORY TX or MULTI TX, the PRINT 1st PAGE IMAGE?
message is displayed. Press [YES] to print the communication report with the first page image, or press [NO] to
print the communication report without the page image.
Setting List/Report
129
Specify the conditions for each transmission type and press [OK].
The RELAY ORIGINATOR, RELAY STATION and RELAY DESTINATION settings are available only when the
FAX Unit (optional) is installed.
When you press [ALWAYS] or [ON ERROR] for each transmission type, the PRINT 1st PAGE IMAGE? message
is displayed. Press [YES] to print the communication report with the first page image, or press [NO] to print the
communication report without the page image.
Setting the reception list
Press [RECEPTION LIST].
The RECEPTION LIST screen is displayed.
130
Setting List/Report

Specify whether the reception list will be printed for each transmission and press [OK].
RELAY STATION Select [ON] to print the reception list when receiving a relay transmission from an originator.
LOCAL Select [ON] to print the reception list when reserving a document to a mailbox within the machine
locally.
REMOTE Select [ON] to print the reception list when receiving a document to a mailbox within the machine
remotely from another facsimile.
Setting List/Report
131
Printing Lists
This menu allows you to print the NIC configuration page, function list, PS3 font list, and PCL font list.
*
For examples of each list format, see the following page:

P.178 List Print Format
Press [LIST/REPORT] in the ADMIN menu.
The LIST/REPORT screen is displayed.

Press [LIST].
The LIST screen is displayed.
Press the button for the list that you want to print.
The selected list is printed.
132
Printing Lists
Setting Printer/e-Filing Functions

This menu allows you to make settings for the printer and e-Filing functions that will apply to the print jobs or e-Filing jobs.
Press [PRINTER/E-FILING] in the ADMIN menu.
The PRINTER/E-FILING screen is displayed.

AUTOMATIC CHANGE OF PAPER SOURCE Selecting [ON] for this function allows the equipment to feed the
same size of paper from a different drawer even if the specified drawer from which paper is being fed is empty.
This function is always enabled when print operations are performed by selecting [Auto] for the paper source on the
print dialog box. For more information about the print dialog box, refer to the Printing Guide.
PAPER OF DIFFERENT DIRECTION Selecting [ON] for this function allows the equipment to feed the same
size of paper that is set in a different direction if the drawer from which paper is being fed is empty.
Paper feeding when the drawer is out of paper during printing is as follows:
This is an example when the drawer for feeding paper is automatically changed while data is being printed on
A4-size paper.
Options
AUTOMATIC CHANGE OF
PAPER SOURCE
Paper Feeding
PAPER OF DIFFERENT
DIRECTION
ON
ON
Selecting [Auto] for the paper

source
Specifying the drawer

manually
ON
OFF
A4 paper is fed.
A4 paper is fed.
OFF
ON
OFF
OFF
A4 paper is fed.
SUSPEND PRINTING IF STAPLER EMPTY Select [ON] to enable suspension of printing if the stapler is empty.
When this is enabled, this equipment will stop printing if the stapler is empty. When this is disabled, this equipment
will print a document without stapling even if the stapler is empty.
Setting Printer/e-Filing Functions
133
Wireless Settings and Bluetooth Settings

There is also [WIRELESS SETTINGS] in the ADMIN menu. This button will be available only when the Wireless LAN
Module (optional) is installed. For instructions on how to operate the WIRELESS SETTINGS, refer to the GN-1050
Operators Manual for Wireless LAN Module.
There is also [Bluetooth SETTINGS] in the ADMIN menu. This button will be available only when the Bluetooth Module
(optional) is installed. For instructions on how to operate the Bluetooth SETTINGS, refer to the GN-2010 Operators
Manual for Bluetooth Module.
134
Wireless Settings and Bluetooth Settings
Change User Password

When the MFP Local Authentication feature is used, administrators can change the authentication password assigned for
each user in case the user forgets the password.
Press [CHANGE USER PASSWORD] in the ADMIN menu.
The CHANGE USER PASSWORD screen is displayed.

[CHANGE USER PASSWORD] is available only when the MFP Local Authentication feature is enabled. For
more information about enabling this feature, refer to the TopAccess Guide.
Set a new password.

1)
2)
3)
4)
Press [USER NAME] to enter the user name for which the password is to be changed.
Press [NEW PASSWORD] to enter the new password.
Press [RETYPE NEW PASSWORD] to enter the new password again.
Press [OK] to save the new password.
y When you press each button ([USER NAME], [NEW PASSWORD] and [RETYPE NEW PASSWORD]), the
on-screen keyboard is displayed. Enter a value using the keyboard and digital keys, and press [OK] to set
the entry.
y The input password appears as asterisks (*) in the [NEW PASSWORD] and [RETYPE NEW PASSWORD]
boxes.
135
IEEE 802.1X Authentication Setting

This menu allows you to make settings for IEEE 802.1X authentication that will apply to wired networks.
This equipment supports the following authentication methods:
y EAP-MD5
y EAP-MSCHAPv2
y EAP-TLS
y PEAP
The following protocol is available for inner authentication:
- EAP-MSCHAPv2
y EAP-TTLS
The following protocols are available for inner authentication:
- PAP
- CHAP
- EAP-MSCHAPv2
- EAP-MD5
The following certificates are required for each authentication method using TopAccess to enable IEEE 802.1X
authentication:
Authentication Method
Inner Authentication Method
CA Certificate
User Certificate
EAP-MD5
EAP-MSCHAPv2
EAP-TLS
Required
Required
PEAP
EAP-MSCHAPv2
Required
EAP-TTLS
PAP
Required
CHAP
Required
EAP-MD5
Required
EAP-MSCHAPv2
Required
For instructions on how to install certificates, refer to the TopAccess Guide.

The settings for IEEE 802.1X authentication depend on the authentication method you select.
Setting IEEE802.1X authentication
Press [802.1X SETTING] in the ADMIN menu.
The WIRED 802.1X SETTINGS screen is displayed.

136

Specify the following items as required and press [Next].
802.1X Press [ENABLE] to enable IEEE802.1X authentication, or [DISABLE] to disable it.

FALL BACK MODE Press [ON] to automatically disable IEEE802.1X authentication when the IEEE 802.1X
authentication switch is not available.
[CHECK SETTINGS] Press this button to confirm the options currently selected.
[FACTORY DEFAULT] Press this button to reset the IEEE802.1X authentication settings back to the factory
defaults.
[CHECK SETTINGS] and FALL BACK MODE are available when you enable IEEE802.1X authentication.
When changing IEEE802.1X authentication from [ENABLE] to [DISABLE], press [Next], and on the Confirm
the following settings screen that appears, press [APPLY NOW] to complete the setting.
P.138 Setting EAP-MSCHAPv2

P.139 Setting EAP-MD5
P.140 Setting EAP-TLS
P.142 Setting PEAP
P.143 Setting EAP-TTLS
137
Setting EAP-MSCHAPv2
Select [EAP-MSCHAPv2] and press [Next].
The WIRED 802.1X SETTINGS (EAP-MSCHAPv2) screen is displayed.
[EAP-USER NAME] Press this button to enter the EAP-User name.

[PASSWORD] Press this button to enter the authentication password.
[RETYPE PASSWORD] Press this button to re-enter the authentication password.
When you press the above buttons, the on-screen keyboard is displayed. Enter a value using the keyboard and
digital keys, and press [OK] to set the entry.
Confirm the settings and press [APPLY NOW].
138

Setting EAP-MD5
Select [EAP-MD5] and press [Next].
The WIRED 802.1X SETTINGS (EAP-MD5) screen is displayed.

139
Setting EAP-TLS
The CA certificate and user certificate must be installed in this equipment before performing settings for IEEE 802.1X
authentication. For instructions on how to install the certificates, refer to the TopAccess Guide.
Select [EAP-TLS] and press [Next].
The WIRED 802.1X SETTINGS (EAP-TLS) screen is displayed.

Use Username from Common Name in the User Certificate Press [ENABLE] to use a common name in the
user certificate as the EAP-User name.
When you enable the [Use Username from Common Name in the User Certificate] option, any user name
cannot be manually entered to the [EAP-USER NAME] box.
When you press [EAP-USER NAME], the on-screen keyboard is displayed. Enter a value using the keyboard
and digital keys, and press [OK] to set the entry.
140

The user certificate installed in this equipment is displayed. Confirm the certificate and
press [Next].
[CRL Verification] shows whether the certificate revocation list (CRL) is enabled or disabled. To use CRL, it is
necessary to upload the certificate revocation list to the equipment from the TopAccess - Security Service
menu. Changing the CRL verification option from [Enable] to [Disable] or vice versa is also performed from
TopAccess. For details, refer to the TopAccess Guide.
141
Setting PEAP
y The CA certificate must be installed in this equipment before performing settings for IEEE 802.1X authentication.
For instructions on how to install the certificate, refer to the TopAccess Guide.
y PEAP is not available for Windows Server 2008.
Select [PEAP] and press [Next].
The WIRED 802.1X SETTINGS (PEAP) screen is displayed.
Select [EAP-MSCHAPv2] for the inner authentication method and press [Next].

142

Setting EAP-TTLS
The CA certificate must be installed in this equipment before performing settings for IEEE 802.1X authentication. For
instructions on how to install the certificate, refer to the TopAccess Guide.
Select [EAP-TTLS] and press [Next].
The WIRED 802.1X SETTINGS (EAP-TTLS) screen is displayed.
143
Select the desired inner authentication method and continue the operation that you
require.
P.144 Setting EAP-MSCHAPv2 for inner authentication

P.145 Setting PAP for inner authentication
P.147 Setting CHAP for inner authentication
P.148 Setting EAP-MD5 for inner authentication
Setting EAP-MSCHAPv2 for inner authentication
Select [EAP-MSCHAPv2] and press [Next].
[EAP-USER NAME] Press this button to enter the EAP-User Name.

144

Setting PAP for inner authentication
Select [PAP] and press [Next].
The WIRED 802.1X SETTINGS (PAP) screen is displayed.
145

146

Setting CHAP for inner authentication
Select [CHAP] and press [Next].
The WIRED 802.1X SETTINGS (CHAP) screen is displayed.

147
Setting EAP-MD5 for inner authentication
Select [EAP-MD5] and press [Next].
The WIRED 802.1X SETTINGS (EAP-MD5) screen is displayed.
148


Error messages
The following error messages may be displayed on the touch panel.
Message
Cause
[802.1X] Auth Server/Switch couldnt be contacted
y The RADIUS server service is stopped.

y Configuration for the RADIUS server is not correct.
y The IEEE 802.1X switch has problem.
[802.1X] Authentication failed
y The username or password that the user entered is not

correct.
y The certificates uploaded are wrong.
[802.1X] Falling back to non-802.1X mode
Network communication has begun using the fall back function,

ignoring IEEE 802.1X authentication.
149
MANAGING COUNTERS (COUNTER MENU)
3.
Total Counter ........................................................................................................................ 152

Print Out Total Counter ........................................................................................................ 155
Department Counter............................................................................................................. 156
Managing Department Codes.............................................................................................. 160
Logging on as administrator ...............................................................................................................................160
Printing department code list ..............................................................................................................................162
Enabling department codes................................................................................................................................163
Resetting all department counters......................................................................................................................164
Deleting all department codes ............................................................................................................................165
Registering a new department code...................................................................................................................166
Editing department codes...................................................................................................................................168
Deleting department codes.................................................................................................................................171
Resetting the counter for each department ........................................................................................................172
Setting output limitations for all departments......................................................................................................173
Setting the no limit black function .......................................................................................................................174
3 MANAGING COUNTERS (COUNTER MENU)
Total Counter
This menu allows you to display and confirm the following total counters:
y Print counter
The print counter contains the following counters:
- Copy counter Indicates the number of sheets that have been printed by copy operations.
- Fax counter Indicates the number of sheets that have been printed by fax receptions.
- Printer counter Indicates the number of sheets that have been printed by print operations and e-mail
receptions (Internet Fax receptions).
- List counter Indicates the number of sheets that have been printed by system page print operations.
y Scan counter
The scan counter contains the following counters:
- Copy counter Indicates the number of originals that have been scanned by copy operations.
- Fax counter Indicates the number of originals that have been scanned by fax and Internet Fax transmissions.
- Network counter Indicates the number of originals that have been scanned by scan operations.
The total counters cannot be cleared.
1
2
Press the [COUNTER] button on the control panel to enter the COUNTER menu.
Press [TOTAL COUNTER].
The TOTAL COUNTER menu is displayed.
P.153 Displaying print counter

P.154 Displaying scan counter
152
Total Counter

3.MANAGING COUNTERS (COUNTER MENU)
Displaying print counter
Press [PRINT COUNTER].
The Print Counter is displayed.
Press the following buttons as required:
y
y
y
y
Press [COPY] to display the total number of copies classified by size group.
Press [FAX] to display the total number of faxes classified by size group.
Press [PRINTER] to display the total number of prints classified by size group.
Press [LIST] to display the total number of printed lists classified by size group.
Total Counter
153
Displaying scan counter
154
Press [SCAN COUNTER].
The SCAN COUNTER is displayed.
Total Counter
Print Out Total Counter

This menu allows you to print the total counter list.
1
2
Press [PRINT OUT TOTAL COUNTER].
y When the department management is disabled, the total counter list is printed.
department code using the digital keys and press [OK] to print the total counter list.
For an output example of the total counter list, see the following page:
P.178 Total counter list
Print Out Total Counter
155
Department Counter
This menu allows you to display and confirm the following counters for each department:
The department counter is available only when this equipment has been managed using the department code.
P.160 Managing Department Codes
y Print counter for department code
This feature allows you to display the number of the print counter for each department code.
The print counter contains the following counters:
- Copy counter Indicates the number of sheets that have been printed by copy operations.
- Fax counter Indicates the number of sheets that have been printed by polling operations.
- Printer counter Indicates the number of sheets that have been printed by print operations.
- List counter Indicates the number of sheets that have been printed by system page print operations.
y Scan counter for department code
This feature allows you to display the number of the scan counter for each department code.
The scan counter contains the following counters:
- Copy counter Indicates the number of originals that have been scanned by copy operations.
- Fax counter Indicates the number of originals that have been scanned by fax and Internet Fax transmissions.
- Network counter Indicates the number of originals that have been scanned by scan operations.
y Fax communications counter for department code
This feature allows you to display the number of the Fax and Internet Fax transmission and reception counter for each
department code.
The fax communication counter contains the following counters:
- Transmit Indicates the number of pages that are sent by Fax transmissions.
- Reception Indicates the number of pages that are received by polling operations.
1
2
Press [COUNTER] on the control panel to enter the COUNTER menu.

Press [DEPARTMENT COUNTER].
The DEPARTMENT CODE screen is displayed.
156
Enter the department number using the digital keys and press [OK].
Department Counter

P.157 Displaying print counter for department code

P.158 Displaying scan counter for department code
P.159 Displaying fax communications counter for department code
Displaying print counter for department code
Press [PRINT COUNTER].
The Print Counter for the specified department code is displayed.
Department Counter
157
Press the following buttons as required.
y
y
y
y
Press [COPY] to display the total number of copies classified by size group.
Press [FAX] to display the total number of faxes classified by size group.
Press [PRINTER] to display the total number of prints classified by size group.
Press [LIST] to display the total number of printed lists classified by size group.
Displaying scan counter for department code
158
Press [SCAN COUNTER].
The SCAN COUNTER for the specified department code is displayed.
Department Counter

Displaying fax communications counter for department code
Press [FAX COMMUNICATION].
The FAX COMMUNICATION counter for the specified department code is displayed.
Department Counter
159
Managing Department Codes

Logging on as administrator
You can audit the copy quantity of copy, print, scan, and facsimile pages performed by setting a department code. Up to
1000 department codes can be registered.
To manage the department codes, you must know the administrator password for this equipment. It is recommended that
this action be performed only by an authorized administrator.
If the User Management Setting is enabled and you log in using a user name with Account Manager privileges, you do
not have to enter the administrator password to display the DEPARTMENT MANAGEMENT menu.
1
2
Press [DEPARTMENT MANAGEMENT].
The ADMINISTRATOR PASSWORD screen is displayed.
Press [PASSWORD].
160

Enter the administrator password and press [OK].
The DEPT. MANAGEMENT menu is displayed.
If the administrator password has not been changed before, enter the default administrator password 123456.
If you enter incorrect passwords three times in a row, the equipment cannot be operated for 30 seconds.
P.162 Printing department code list

P.163 Enabling department codes
P.164 Resetting all department counters
P.165 Deleting all department codes
P.166 Registering a new department code
P.168 Editing department codes
P.171 Deleting department codes
P.172 Resetting the counter for each department
P.173 Setting output limitations for all departments
P.174 Setting the no limit black function
Menus other than DEPARTMENT MANAGEMENT and DEPARTMENT REGISTRATION will be available
after you register a department code and enable the department management feature.
161
Printing department code list

You can print out the department code list and counters for each department code.
In the DEPT. MANAGEMENT menu, press [PRINT OUT DEPARTMENT CODES].
Printing begins.
y For instructions on how to display the screen above, see the following page:
P.160 Logging on as administrator
y For an output example of the department code list, see the following page:
P.179 Department code list
162

Enabling department codes

In the initial setting, the department code feature is disabled. If you want to manage the counter separately by department
codes, you must enable department codes. When department management is enabled, the department code input screen
will be displayed before entering the copy, scan, fax, and e-Filing operation screens to manage the operations for each
department code. In addition, print jobs that are sent from computers can be managed for each department code.
y [DEPARTMENT MANAGEMENT] will be available after registering a department code. Before enabling the
department code, register the required department code.
y Using TopAccess, you can also configure department code enforcement settings specifying whether invalid jobs,
for which a department code is not specified or for which the department code is invalid, will be printed or stored in
the invalid job list when department management is enabled. For instructions on how to set the department code
enforcement, refer to the TopAccess Guide.
y The department management function does not support Web Services Scan. Web Services Scan jobs performed
when department management is enabled are always counted as Undefined Department Name.
In the DEPT. MANAGEMENT menu, press [DEPARTMENT MANAGEMENT].
The DEPARTMENT MANAGEMENT screen is displayed.
For instructions on how to display the screen above, see the following page:
Press [ENABLE] to enable the department code, or [DISABLE] to disable the

department code.
163
Resetting all department counters

This function clears all department counters to 0.
y This function is available only when the department code is enabled.

y This function clears only the department counters. You cannot clear the total counter.
In the DEPT. MANAGEMENT menu, press [RESET ALL COUNTERS].
The clear confirmation screen is displayed.
Press [YES] to clear all department counters.
Press [NO] to cancel the clear operation.
164

Deleting all department codes

This function deletes all registered department codes.
[DELETE ALL] will be available after you enable the department management function and register a department
code.
In the DEPT. MANAGEMENT menu, press [DELETE ALL].
Press [YES] to delete all department codes.
165
Registering a new department code

This function allows you to register new department codes.
After registering the department code(s), you must enable the department management function.
In the DEPT. MANAGEMENT menu, press [DEPARTMENT REGISTRATION].
Press an undefined button to create a new department code and press [CHANGE].
If the touch panel does not display an undefined department code, press
166

Enter the department name using the keyboard and digital keys, and press [OK].
The REGISTRATION DEPARTMENT CODE screen is displayed.
Set the department code.

1) Press the [NEW CODE] box and enter a 5-digit code using the digital keys.
2) Press the [RETYPE NEW CODE] box and re-enter the 5-digit code using the digital keys.
3) Press [OK] to save the department code.
The LIMITATION screen appears.
The department code must be a 5-digit code excluding 00000.
y If you enter the code, asterisks (*) appear in the [NEW CODE] and [RETYPE NEW CODE] boxes.
y If you want to clear the code to retype it, press the [CLEAR] button on the control panel.
167
Set the limitation of this department code as required and press [OK] to register the
new department code.
COLOR Press [ON] to enable color output limitation for this department code. When you select [ON], enter the
maximum number of the color outputs for this department code in the [Limitation] box using the digital keys. You
can enter up to 99999999. If not setting an output limitation for color outputs, press [OFF].
BLACK Press [ON] to enable black output limitation for this department code. When you select [ON], enter the
maximum number of black outputs for this department code in the [Limitation] box using the digital keys. You can
enter up to 9999999. If not setting an output limitation for black outputs, press [OFF].
y If you enter 0 for the limitation, it will disable printing any copies or prints using this department code.
y When the No Limit Black function is enabled, you cannot set the limitation for black.
y When the number of outputs exceeds the limitation during the job being printed, a few copies that exceed
the limitation are printed and counted because the equipment cannot stop the job immediately.
Editing department codes

This function allows you to edit an existing department code.
168

Press the department button that you want to edit and press [CHANGE].
The message This department code is already registered. Do you wish to replace this code? is displayed.
If the touch panel does not display the department code that you want to edit, press
screen.
to display the next
Press [OK].
Enter the department name using the keyboard and digital keys, and press [OK].
The CHANGE DEPARTMENT CODE screen is displayed.
169
Change the department code to a different one.

1)
2)
3)
4)
Press [CURRENT CODE] to enter the current department code using the digital keys.
Press [NEW CODE] to enter a new 5-digit code using the digital keys.
Press [RETYPE NEW CODE] to re-enter the new 5-digit code using the digital keys.
Press [OK] to save the department code.
The LIMITATION screen appears.
y When you enter the code, asterisks (*) appear in each box ([CURRENT CODE], [NEW CODE] and
[RETYPE NEW CODE]).
y If you want to clear the code to retype it, press the [CLEAR] button on the control panel.
The department code must be a 5-digit code, excluding 00000.
Set the limitation of this department code as required and press [OK].
170

Deleting department codes

This function allows you to delete an existing department code.
Press the department button that you want to delete and press [DELETE].
If the touch panel does not display the department code that you want to delete, press
screen.
to display the next
Press [YES] to delete the department code.
171
Resetting the counter for each department

This function allows you to reset the counter for the specified department code.
Press the department button whose counter you want to reset and press [RESET
COUNTERS].
The clear confirmation screen is displayed.
If the touch panel does not display the department code whose counter you want to clear, press
the next screen.
Press [YES] to clear the department code counter.
Press [NO] to cancel the clear operation.
172
to display

Setting output limitations for all departments

This function allows you to set the output limitations for all departments through a single operation.
When you select [ON], output will be disabled for all departments.
When you select [OFF], unlimited outputs will be allowed for all departments.
When you select [ON], the limitation settings for each department code will be set to [ON] and the [Limitation] box will
be set to 0. If you want to change the limitation settings for each department code, change the limitation settings by
editing a department code.
P.168 Editing department codes
In the DEPT. MANAGEMENT menu, press [ALL LIMIT].
The ALL LIMIT screen is displayed.
COLOR Press [ON] to disable color copies/prints for all departments, or [OFF] to permit unlimited color copies/
prints for all departments.
BLACK Press [ON] to disable black copies/prints for all departments, or [OFF] to permit unlimited black copies/
prints for all departments.
The all limit function for black cannot be set when the no limit black function is enabled.
The output limitation settings are saved. After you press [OK], the message WAIT is displayed until the setting
is applied. This may take some time depending on the number of registered department codes.
173
Setting the no limit black function

When the no limit black function is enabled, users can perform unlimited black copies/prints on this equipment and it will
not count the number of black copies/prints for each department code.
When the department management function is disabled, the no limit black function is also disabled. Therefore, the no
limit black function is disabled every time you enable the department management function. If you want to enable the
no limit black function, you must enable it after enabling the department management function.
In the DEPT. MANAGEMENT menu, press [NO LIMIT BLACK].
The NO LIMIT BLACK COPY/PRINT screen is displayed.
Press [ENABLE] to enable the no limit black function, or [DISABLE] to disable the no
limit black function.
The no limit black setting is saved.
174

When the MFP Local Authentication feature is used, this function allows each user to change his or her authentication
password that has been entered in the authentication screen.
1
2
Press [CHANGE USER PASSWORD].
The CHANGE USER PASSWORD screen is displayed.
[CHANGE USER PASSWORD] is available only when the MFP Local Authentication feature is enabled.
Change the password.

1) Press [NEW PASSWORD] to enter the new password.
2) Press [RETYPE NEW PASSWORD] to re-enter the new password.
3) Press [OK] to save the new password.
You will be returned to the User Authentication screen.
y When you press each button ([NEW PASSWORD] and [RETYPE NEW PASSWORD]), the on-screen
keyboard is displayed. Enter a value using the keyboard and digital keys, and press [OK] to set the entry.
y The input password appears as asterisks (*) in the [NEW PASSWORD] and [RETYPE NEW PASSWORD]
boxes.
175
APPENDIX
4.
List Print Format................................................................................................................... 178

Total counter list..................................................................................................................................................178
Department code list...........................................................................................................................................179
Address book information...................................................................................................................................180
Group number information .................................................................................................................................181
Function list (User) .............................................................................................................................................182
NIC configuration page.......................................................................................................................................183
Function list (Administrator)................................................................................................................................184
PS3 font list ........................................................................................................................................................198
PCL font list ........................................................................................................................................................199
4 APPENDIX
List Print Format

Total counter list
Output example of the TOTAL COUNTER LIST
TOTAL COUNTER LIST

TIME
S/N
PRINT COUNTER
TOTAL
COPY
FAX
PRINTER
LIST
TOTAL
COPY
TWIN/MONO COLOR
BLACK
TOTAL
99999
99999
99999
99999
99999
99999
99999
99999
99999
99999
99999
99999
299996
299996
299996
299996
399996
399996
399996
1199988
BLACK
TOTAL
FULL COLOR
TWIN/MONO COLOR
SMALL
LARGE
16667
16667
16666
16665
16667
16667
399996
399996
TOTAL
33334
33331
33334
99999
FAX
FULL COLOR
TWIN/MONO COLOR
BLACK
TOTAL
SMALL
LARGE
16667
16667
16666
16665
16667
16667
399996
399996
TOTAL
33334
33331
33334
99999
PRINTER
FULL COLOR
TWIN/MONO COLOR
BLACK
TOTAL
SMALL
LARGE
16667
16667
16666
16665
16667
16667
399996
399996
TOTAL
33334
33331
33334
99999
LIST
FULL COLOR
TWIN/MONO COLOR
BLACK
TOTAL
SMALL
LARGE
16667
16667
16666
16665
16667
16667
399996
399996
TOTAL
33334
33331
33334
99999
SCAN COUNTER
178
FULL COLOR
: 15-05-'08 20:47
: 0987654321
FULL COLOR
TWIN/MONO COLOR
BLACK
TOTAL
SMALL
LARGE
16667
16667
16666
16665
16667
16667
399996
399996
TOTAL
33334
33331
33334
99999
List Print Format
4 APPENDIX
4.APPENDIX
Department code list

Output example of the DEPARTMENT CODE LIST
DEPARTMENT CODE LIST

TIME
DEPT NO.
DEPARTMENT
D 1
00001
: 15-05-'08 20:47
PRINT COUNTER
FULL COLOR
COPY
SMALL
LARGE
TWIN/MONO COLOR
PRINT
TOTAL
99999
99999
99999
99999
199998
199998
199998
199998
399996
COPY
FAX
COPY
LIMIT
SMALL
LARGE
-
PRINT
TOTAL
99999
99999
99999
99999
199998
199998
199998
199998
399996
BLACK
SMALL
LARGE
PRINT
TOTAL
LIST
99999
99999
99999
99999
99999
99999
99999
99999
399996
399996
199998
199998
199998
199998
799992
FULL COLOR
TRANSMIT
RECEPTION
99999
99999
99999
99999
199998
199998
DEPT NO.
DEPARTMENT
D 2
00002
SCAN COUNTER
FAX COMMUNICATION
SMALL
LARGE
LIMIT
SMALL
LARGE
TWIN/MONO COLOR
NETWORK
COPY
NETWORK
COPY
BLACK
COPY
FAX
NETWORK
99999
99999
99999
99999
99999
99999
99999
99999
99999
99999
99999
99999
99999
99999
199998
199998
199998
199998
199998
199998
199998
PRINT COUNTER
FULL COLOR
COPY
SMALL
LARGE
TWIN/MONO COLOR
PRINT
TOTAL
99999
99999
99999
99999
199998
199998
199998
199998
399996
LIMIT
COPY
SMALL
LARGE
PRINT
TOTAL
99999
99999
99999
99999
199998
199998
199998
199998
399996
List Print Format
179
4 APPENDIX
Address book information

Output example of the ADDRESS BOOK INFORMATION
ADDRESS BOOK INFORMATION
180
: 15-05-'08 20:47
FAX NO.1
: 99999999999
FAX NO.2
: 99999999990
NAME
: MFP_00000183
NO.
NAME
001
USER01
00000000001
[email protected]
OFF
MEMORY
OFF
002
USER01
00000000002
[email protected]
OFF
MEMORY
OFF
003
USER01
00000000003
[email protected]
OFF
MEMORY
OFF
004
USER01
00000000004
[email protected]
OFF
MEMORY
OFF
005
USER01
00000000005
[email protected]
OFF
MEMORY
OFF
006
USER01
00000000006
[email protected]
OFF
MEMORY
OFF
007
USER01
00000000007
[email protected]
OFF
MEMORY
OFF
008
USER01
00000000008
[email protected]
OFF
MEMORY
OFF
009
USER01
00000000009
[email protected]
OFF
MEMORY
OFF
010
USER01
00000000010
[email protected]
OFF
MEMORY
OFF
011
USER01
00000000011
[email protected]
OFF
MEMORY
OFF
OFF
012
USER01
00000000012
[email protected]
OFF
MEMORY
OFF
OFF
List Print Format
FAX NUMBER/E-MAIL ADDRESS
TIME
QUALITY TX
TX TYPE
LINE
ECM
ATT
4 APPENDIX
4.APPENDIX
Group number information

Output example of the GROUP NUMBER INFORMATION
GROUP NUMBER INFORMATION
NO.
NAME
001
GROUP01
TIME
: 15-05-'08 20:47
FAX NO.1
: 99999999999
FAX NO.2
: 99999999990
NAME
: MFP_00000183
ADDRESS BOOK
001
001
002
003
004
005
005
006
006
007
007
008
008
009
009
010
010
011
012
013
014
014
015
015
016
016
017
017
018
018
019
019
020
020
002
GROUP02
005
007
009
015
060
065
003
GROUP03
005
005
006
007
008
009
List Print Format
181
4 APPENDIX
Function list (User)

Output example of the FUNCTION LIST (User)
FUNCTION LIST
S/N
: 0987654321
TIME
: 15-05-'08 20:47
F/W Ver.
: T380SY0U010
FAX NO.1
: 99999999999
M-ROM Ver.
: 380M-014
FAX NO.2
: 99999999990
S-ROM Ver.
: 380S-01
NAME
: MFP_00000183
GENERAL
TOTAL COUNTER
DRAWER
DRAWER
DRAWER
DRAWER
DRAWER
AUTO CLEAR
9999
:
:
:
:
:
LT
A3
A4-R
B5
45
EXPOSURE FOR COLOR

EXPOSURE FOR BLACK
COLOR MODE
IMAGE DIRECTION
BYPASS FEED
ORIGINAL MODE FOR COLOR
ORIGINAL MODE FOR BLACK
ORIGINAL MODE FOR AUTO COLOR
:
:
:
:
:
:
:
:
MANUAL
AUTO
BLACK
DISABLE
PLAIN
TEXT/PHOTO
TEXT/PHOTO
TEXT/PHOTO
COLOR MODE
COMPRESS
B/W ADJUSTMENT IN ACS
ROTATION
SINGLE/2-SIDE SCAN
IMAGE QUALITY FOR BLACK
PREVIEW SETTING
INITIAL PREVIEW TYPE
OMIT BLANK PAGE ADJUSTMENT
ACS ADJUSTMENT
COLOR
RESOLUTION
ORIGINAL MODE
EXPOSURE
BACKGROUND ADJUSTMENT
:
:
:
:
:
:
:
:
:
:
BLACK
MID
3
0
SINGLE
STANDARD
OFF
PAGE FIT
0
2
:
:
:
:
200dpi
TEXT
AUTO
1
2
3
4
COPY
SCAN
For further information about the items printed in the function list, see the following page:
P.184 Function list (Administrator)
182
List Print Format
4 APPENDIX
4.APPENDIX
NIC configuration page

Output example of the NIC Configuration Page
===================================================================================
Unit Serial No
: 04998820
Network Address
: 00:40:af:7e:28:55
Network Topology
: Ethernet
Network Mode
: Auto
Novell Network Information

Print Server Name
Password Defined
Search Root not defined
Directory Services Tree
Directory Services Context
Scan Rate
Frame Type
TCP/IP Network Information
Address Mode
:
IP Address
:
Subnet Mask
:
Default Gateway
:
Primary DNS Server :
DNS Name
:
Host Name
:
Primary WINS Server :
NetBios Name
:
IPP Network Information
IPP without SSL
IPP with SSL
Version : T000SY00000
Connector: RJ45
enabled
: MFP_04998820
:
:
:
:
:
ORG
dept1.org
5
Auto Sense
for IPv4
Static IP
10.10.70.120
255.255.255.0
10.10.70.1
0.0.0.0
enabled
MFP-04998820
0.0.0.0
MFP-04998820
enabled
: http://10.10.70.120:631/Print
: https://10.10.70.120:443/Print
AppleTalk Network Information

enabled
AppleTalk Printer Name: MFP_00C67861
AppleTalk Zone
: *
AppleTalk Type
: LaserWriter
AppleTalk Frame Type : 802.2 SNAP On 802.3
===================================================================================
Novell Connection Information
File Server Name: NWSRV
Queue Name: MFP_QUEUE
AppleTalk Connection Information
AppleTalk Printer Name: MFP_00C67861
Raw Socket Connection Information
Port Number: 9100
List Print Format
183
4 APPENDIX
Function list (Administrator)

Output example of the FUNCTION LIST (Administrator)
FUNCTION LIST
S/N
: 0987654321
TIME
: 15-05-'08 20:47
F/W Ver.
: T380SY0U010
FAX NO.1
: 99999999999
M-ROM Ver.
: 380M-014
FAX NO.2
: 99999999990
S-ROM Ver.
: 380S-01
NAME
: MFP_00000183
GENERAL
TOTAL COUNTER
MAIN / PAGE MEMORY SIZE
DRAWER
DRAWER 1
DRAWER 2
DRAWER 3
DRAWER 4
AUTO CLEAR
ENERGY SAVER
WEEKLY TIMER
TIMER SUNDAY
TIMER MONDAY
TIMER TUESDAY
TIMER WEDNESDAY
TIMER THURSDAY
TIMER FRIDAY
TIMER SATURDAY
AUTO POWER SAVE
SLEEP MODE
:
:
9999
512 MB / 256 MB
:
:
:
:
:
LT
LD
LT-R
A4
45
:
:
:
:
:
:
:
:
:
ON
00:00
00:00
00:00
00:00
00:00
00:00
00:00
15
60
DRAWER
PAPER JAM RECOVERY
:
:
ENABLE
DISABLE
EXPOSURE FOR COLOR

EXPOSURE FOR BLACK
COLOR MODE
IMAGE DIRECTION
BYPASS FEED
ACS ADJUSTMENT
MAXIMUM COPIES :
:
:
:
:
:
:
:
:
MANUAL
AUTO
BLACK
DISABLE
PLAIN
TEXT/PHOTO
TEXT/PHOTO
TEXT/PHOTO
OFF
24:00
24:00
24:00
24:00
24:00
24:00
24:00
POP-UP
COPY
9999
The Function List for an administrator shows the setting list for all functions. The following table shows all functions that
are printed in an administrators function list, and the User column indicates which functions are printed in a users
function list. This table also describes each function.
GENERAL
Function
184
Description
User
TOTAL COUNTER
Shows the total counter.
YES
MAIN / PAGE MEMORY SIZE
Shows the main memory size and page memory size.
NO
DRAWER - DRAWER 1
Shows the paper size for drawer 1.
YES
DRAWER - DRAWER 2
YES
DRAWER - DRAWER 3 *1
YES
DRAWER - DRAWER 4 *2
YES
DRAWER
- LARGE CAPACITY FEEDER *3
Shows the paper size for the large capacity feeder
AUTO CLEAR
Shows the time (in seconds) it takes the touch panel

display to clear the previous settings and return to the initial
screen.
List Print Format
YES
YES
4 APPENDIX
4.APPENDIX
GENERAL
Function
Description
User
Shows the time to enter the energy saver mode (ON time),
and the time to exit the energy saver mode (OFF time) for
each day (Sunday to Saturday).
NO
ENERGY SAVER - AUTO POWER SAVE
Shows the time to enter the power save mode (in minutes).
NO
ENERGY SAVER - SLEEP MODE
Shows the time to enter the sleep mode (in minutes).
NO
ENERGY SAVER - WEEKLY TIMER
*1 DRAWER 3 is printed only when Drawers 3 & 4 are installed.

*2 DRAWER 4 is printed only when Drawers 3 & 4 are installed.
*3 LARGE CAPACITY FEEDER is printed only when the LCF is installed.
POP-UP
Function
Description
User
DRAWER
Shows whether the drawer set pop-up is enabled or

disabled.
NO
PAPER JAM RECOVERY
Shows whether the paper jam recovery pop-up is enabled

or disabled.
NO
COPY
Function
Description
User
EXPOSURE FOR COLOR
Shows the default exposure setting for color copies.
YES
EXPOSURE FOR BLACK
Shows the default exposure setting for black copies.
YES
COLOR MODE
Shows the default color mode for copies.
YES
IMAGE DIRECTION
Shows whether the image direction is enabled or disabled.
YES
BYPASS FEED
Shows the default paper type of the bypass feed.
YES
Shows the default original mode for color copies.
YES
Shows the default original mode for black copies.
YES
Shows the default original mode for auto color copies.
YES
Shows the omit blank page adjustment level.
YES
ACS ADJUSTMENT
Shows the ACS adjustment level.
YES
MAXIMUM COPIES
Shows the maximum copies that are allowed to be set.
NO
AUTO 2-SIDE MODE
Shows the default auto 2-sided mode.
NO
SORT MODE PRIORITY
Shows the default sort mode.
NO
AUTOMATIC CHANGE OF PAPER SOURCE
Shows whether the Automatic Change of Paper Source

function is enabled or disabled.
NO
PAPER OF DIFFERENT DIRECTION
Shows whether the Paper of Different Direction function is

enabled or disabled.
NO
SUSPEND PRINTING IF STAPLER EMPTY
Shows whether this equipment suspends printing when

stapler empty occurs.
NO
DEFAULT MODE OF AUTO COLOR
Shows the default color mode for auto color mode.
NO
SCAN
Function
Description
User
COLOR MODE
Shows the default color mode for scan.
YES
COMPRESS
Shows the default compression setting.
YES
B/W ADJUSTMENT IN ACS
Shows the default B/W resolution in ACS.
YES
List Print Format
185
4 APPENDIX
SCAN
Function
Description
User
ROTATION
Shows the default rotation mode.
YES
SINGLE/2-SIDED SCAN
Shows the default 2-sided scan mode.
YES
IMAGE QUALITY FOR BLACK
Shows the default image quality setting that applies when

scanning a black original in auto color mode.
YES
PREVIEW SETTING
Shows whether the preview function is enabled or disabled.
YES
INITIAL PREVIEW TYPE
Shows the default preview type.
YES
Shows the omit blank page adjustment level.
YES
ACS ADJUSTMENT
Shows the ACS adjustment level.
YES
COLOR - RESOLUTION
Shows the resolution for color scans.
YES
COLOR - ORIGINAL MODE
Shows the default original mode for color scans.
YES
COLOR - EXPOSURE
Shows the default exposure setting for color scans.
YES
COLOR - BACKGROUND ADJUSTMENT
Shows the default background adjustment setting for color

scans.
YES
GRAY SCALE - RESOLUTION
Shows the resolution for grayscale scans.
YES
GRAY SCALE - EXPOSURE
Shows the default exposure setting for grayscale scans.
YES
GRAY SCALE
- BACKGROUND ADJUSTMENT
Shows the default background adjustment setting for

grayscale scans.
YES
BLACK - RESOLUTION
Shows the resolution for black scans.
YES
BLACK - ORIGINAL MODE
Shows the default original mode for black scans.
YES
BLACK - EXPOSURE
Shows the default exposure setting for black scans.
YES
BLACK - BACKGROUND ADJUSTMENT
Shows the default background adjustment setting for black

scans.
YES
Description
User
FAX
Function
186
FAX ROM VERSION
Shows the ROM version of the Fax unit.
YES
RESOLUTION
Shows the default resolution setting for a fax/Internet Fax

transmission.
YES
ORIGINAL MODE
Shows the default original mode for a fax/Internet Fax

transmission.
YES
EXPOSURE
Shows the default exposure setting for a fax/Internet Fax

transmission.
YES
TX TYPE *1
Shows the default transmission type.
YES
TTI
Shows whether the TTI is enabled or disabled.
NO
RTI
Shows whether the RTI is enabled or disabled.
YES
ECM *1
Shows whether the ECM is enabled or disabled.
YES
INITIAL SETUP - MONITOR VOLUME *1
Shows the monitor volume setting.
NO
INITIAL SETUP
- COMPLETION TONE VOLUME *1
Shows the complete volume setting.
INITIAL SETUP - RX MODE *1
Shows the default RX mode.
NO
INITIAL SETUP - DIAL TYPE *1
Shows the dial type of line 1.
NO
List Print Format
NO
4 APPENDIX
4.APPENDIX
FAX
Function
Description
User
INITIAL SETUP - DIAL TYPE (LINE2) *2
Shows the dial type of line 2.
NO
LINE-2 MODE *2
Shows the line 2 mode.
NO
LINE-2 MODE - START *2
Shows the start time to use Line 2 for receptions only. This
applies only when RX ONLY (TIMER) is set to LINE-2
MODE.
NO
Shows the end time to finish using Line 2 for receptions

only. This applies only when RX ONLY (TIMER) is set to
LINE-2 MODE.
NO
RX PRINT - DISCARD
Shows whether the discard function is enabled or disabled.
NO
RX PRINT - REDUCTION
Shows whether reduction is enabled or disabled.
NO
RX PRINT - DUPLEX PRINT *1
Shows whether duplex print is enabled or disabled.
NO
RX PRINT - ROTATE SORT *1
Shows whether rotate sort is enabled or disabled.
NO
RECOVERY TX *1
Shows whether recovery transmission is enabled or

disabled.
NO
RECOVERY TX - STORED TIME *1
Shows how many hours a recovery transmission job is to

be stored.
NO
LINE-2 MODE - END *2
FAX RECEIVED FORWARD - AGENT1
*1
Shows the agent type if the Fax Received Forward is

registered.
NO
FAX RECEIVED FORWARD - AGENT2
*1
Shows the agent type if the Fax Received Forward is

registered.
NO
*1 These are printed only when the FAX Unit (optional) is installed.
*2 These are printed only when the FAX Unit (optional) and 2nd Line for FAX Unit (optional) are installed.
E-FILING
Function
PRINTING IMAGE MODE
Description
User
Shows the default printing image mode.
YES
FILE
Function
Description
User
MAINTENANCE
Shows whether storage maintenance is enabled or

disabled.
NO
STORAGE MAINTENANCE
Shows how many days the data in the local folder is stored.
This applies only when the maintenance function is
enabled.
NO
Description
User
FRAGMENT MESSAGE SIZE (KB)
Shows the fragment message size that applies to an e-mail

transmission.
NO
FROM ADDRESS
Shows the senders e-mail address that applies to an email transmission.
NO
FROM NAME
Shows the senders name that applies to an e-mail

transmission.
NO
NUMBER OF RETRY
Shows how many times this equipment tries to send an email when it had previously failed.
NO
RETRY INTERVAL
Shows the interval of an e-mail transmission.
NO
E-MAIL
Function
List Print Format
187
4 APPENDIX
E-MAIL
Function
Description
User
ADDRESS SPECIFYING METHOD
Shows the address specifying method that applies to an email transmission.
NO
BCC ADDRESS DISPLAY
Shows whether Bcc address display is enabled or disabled.
NO
Description
User
INTERNET FAX
Function
FRAGMENT PAGE SIZE (KB)
Shows the fragment message size that applies to an

Internet Fax transmission.
NO
BODY STRING TRANSMISSION
Shows whether the body string transmission is enabled or

disabled.
NO
FROM ADDRESS
Shows the senders e-mail address that applies to an

Internet Fax transmission.
NO
FROM NAME
Shows the senders name that applies to an Internet Fax

transmission.
NO
INTERNET FAX RECEIVED FORWARD - AGENT1
Shows the agent type if the Internet Fax Received Forward

is registered.
NO
INTERNET FAX RECEIVED FORWARD - AGENT2
Shows the agent type if the Internet Fax Received Forward

is registered.
NO
NUMBER OF RETRY
Shows how many times this equipment tries to send an

Internet Fax when it had previously failed.
NO
RETRY INTERVAL
Shows the interval of an Internet Fax transmission.
NO
REPORT SETTING
Function
188
Description
User
JOURNAL - AUTO
Shows whether auto journal print is enabled or disabled.
NO
JOURNAL - TX JOURNAL
Shows how many transmissions will be printed in a

transmission journal.
NO
JOURNAL - RX JOURNAL
Shows how many receptions will be printed in a reception

journal.
NO
COMM. REPORT - MEMORY TX
Shows the conditions for printing a memory transmission

report.
NO
COMM. REPORT - DIRECT TX
Shows the conditions for printing a direct transmission

report.
NO
COMM. REPORT - MULTI TX
Shows the conditions for printing a multi transmission

report.
NO
COMM. REPORT - POLLING *1
Shows the conditions for printing a polling report.
NO
COMM. REPORT - RELAY ORIGINATOR*1
Shows the conditions for printing a relay originator report.
NO
COMM. REPORT - RELAY STATION*1
Shows the conditions for printing a relay station report.
NO
COMM. REPORT - RELAY DESTINATION*1
Shows the conditions for printing a relay destination report.
NO
RECEPTION LIST - LOCAL
Shows whether a reception list will be printed or not after

reserving a document to a mailbox within the equipment.
NO
RECEPTION LIST - REMOTE

reserving a document to a mailbox within the equipment
remotely from another facsimile.
NO
List Print Format
4 APPENDIX
4.APPENDIX
REPORT SETTING
Function
RECEPTION LIST - RELAY STATION
Description
User

receiving a relay transmission from an originator as a relay
hub.
NO
*1 These are printed only when the FAX Unit (optional) is installed.
PRINTER/E-FILING
Function
Description
User
AUTOMATIC CHANGE OF PAPER SOURCE
Shows whether the Automatic Change of Paper Source

function is enabled or disabled.
NO
PAPER OF DIFFERENT DIRECTION
Shows whether the Paper of Different Direction function is

NO
SUSPEND PRINTING IF STAPLER EMPTY
Shows whether this equipment suspends printing when

stapler empty occurs.
NO
WIRED 802.1X SETTING

Function
Description
User
ENABLE 802.1X
Shows whether the wired 802.1X authentication is enabled

or disabled.
NO
ENABLE FALL BACK
Shows whether the fall back mode is enabled or disabled.
NO
FALL BACK RETRY COUNT
Shows the fall back retry count.
NO
EAP-METHOD
Shows the current EAP-method.
NO
WIRELESS SETTINGS
Function
WIRELESS LAN
Description
User
Shows whether the Wireless LAN function is enabled or

disabled.
NO
WIRELESS SETTINGS are printed only when the Wireless LAN Module (optional) is installed.
BLUETOOTH SETTINGS
Function
Description
User
BLUETOOTH
Shows whether the Bluetooth function is enabled or

disabled.
NO
BLUETOOTH NAME
Shows the Bluetooth name of this equipment.
NO
DEVICE ADDRESS
Shows the device address of this equipment.
NO
ALLOW DISCOVERY
Shows whether the Allow Discovery function is enabled or

disabled.
NO
SECURITY
Shows whether the security function is enabled or disabled.
NO
REQUIRED PIN
Shows the PIN number.
NO
DATA ENCRYPTION
Shows whether the data encryption is enabled or disabled.
NO
List Print Format
189
4 APPENDIX
BLUETOOTH SETTINGS are printed only when the Bluetooth Module (optional) is installed.
NETWORK SETTING - GENERAL PRODUCT - GENERAL
Function
ETHERNET SPEED DUPLEX MODE
Description
Shows the Ethernet speed setting.
User
NO
NETWORK SETTING - NETWORK - TCP/IP

Function
Description
User
ADDRESS MODE
Shows the TCP/IP address mode.
NO
IP ADDRESS
Shows the IP address of this equipment.
NO
SUBNET MASK
Shows the subnet mask of this equipment.
NO
DEFAULT GATEWAY
Shows the default gateway address of this equipment.
NO
NETWORK SETTING - NETWORK - IPv6

Function
190
Description
User
ENABLE IPv6
Shows whether the IPv6 protocol is enabled or disabled.
NO
ADDRESS MODE
Shows the IPv6 address mode.
NO
LLMNR
Shows whether the LLMNR (Linklocal Multi-cast Name

Resolution) is enabled or disabled.
NO
LINK LOCAL ADDRESS
Shows the link local address of this equipment.
NO
IP ADDRESS
Shows the IPv6 address of this equipment.
NO
PREFIX LENGTH
Shows the prefix length of the IPv6 address.
NO
DEFAULT GATEWAY
Shows the default gateway address of this equipment.
NO
USE DHCPv6 SERVER FOR OPTIONS
Shows whether the optional information is obtained from

the DHCPv6 server.
NO
KEEP CONFIGURATION FOR STATELESS
Shows whether the stateless address configuration is kept.
NO
USE STATFULL FOR IP ADDRESS (M FLAG)
Shows whether the stateful usage (IP address acquisition

M flag) is enabled or disabled.
NO
USE STATFULL FOR OPTIONS (O FLAG)
Shows whether the stateful usage (optional information

acquisition O flag) is enabled or disabled.
NO
List Print Format
4 APPENDIX
4.APPENDIX
NETWORK SETTING - NETWORK - IPv6

Function
IP ADDRESS1
Description
User
IP address, prefix length and gateway which are issued

from routers.
NO
PREFIX LENGTH1
NO
GATEWAY1
NO
IP ADDRESS2
NO
PREFIX LENGTH2
NO
GATEWAY2
NO
IP ADDRESS3
NO
PREFIX LENGTH3
NO
GATEWAY3
NO
IP ADDRESS4
NO
PREFIX LENGTH4
NO
GATEWAY4
NO
IP ADDRESS5
NO
PREFIX LENGTH5
NO
GATEWAY5
NO
IP ADDRESS6
NO
PREFIX LENGTH6
NO
GATEWAY6
NO
IP ADDRESS7
NO
PREFIX LENGTH7
NO
GATEWAY7
NO
USE STATFUL FOR IP ADDRESS
Shows whether the stateful usage (IP address acquisition)

is enabled or disabled.
NO
USE STATFUL FOR OPTIONS
Shows whether the stateful usage (optional information

acquisition) is enabled or disabled.
NO
NETWORK SETTING - NETWORK - IPX/SPX

Function
Description
User
ENABLE IPX/SPX
Shows whether the IPX/SPX protocol is enabled or

disabled.
NO
FRAME TYPE
Shows the frame type to be selected.
NO
NETWORK SETTING - NETWORK - APPLETALK

Function
Description
User
ENABLE APPLE TALK
Shows whether the AppleTalk protocol is enabled or

disabled.
NO
DEVICE NAME
Shows the AppleTalk device name.
NO
DESIRED ZONE
Shows the AppleTalk zone.
NO
List Print Format
191
4 APPENDIX
NETWORK SETTING - SESSION - LDAP SESSION

Function
Description
User
ENABLE LDAP
Shows whether the LDAP is enabled or disabled.
NO
ENABLE SSL
Shows whether the LDAP SSL is enabled or disabled.
NO
NETWORK SETTING - SESSION - DNS SESSION

Function
Description
User
ENABLE DNS
Shows whether the DNS is enabled or disabled.
NO
PRIMARY DNS SERVER ADDRESS
Shows the primary DNS server address if it has been set.
NO
SECONDARY DNS SERVER ADDRESS
Shows the secondary DNS server address if it has been

set.
NO
PRIMARY DNS SERVER ADDRESS (IPv6)
Shows the primary DNS server IPv6 address if it has been

set.
NO
SECONDARY DNS SERVER ADDRESS (IPv6)
Shows the secondary DNS server IPv6 address if it has

been set.
NO
NETWORK SETTING - SESSION - DDNS SESSION

Function
Description
User
ENABLE DDNS
Shows whether the DDNS is enabled or disabled.
NO
HOST NAME
Shows the host name of this equipment.
NO
DOMAIN NAME
Shows the domain name of this equipment.
NO
NETWORK SETTING - SESSION - SMB SESSION

Function
Description
User
SMB SERVER PROTOCOL
Shows whether the SMB protocol is enabled or disabled.
NO
ENABLE IPv6
Shows whether the IPv6 protocol is enabled or disabled.
NO
NETBIOS NAME
Shows the NetBIOS name of this equipment.
NO
LOGON
Shows the logon setting.
NO
WORKGROUP
Shows the workgroup of this equipment.
NO
DOMAIN
Shows the domain name of this equipment.
NO
PRIMARY DOMAIN CONTROLLER
Shows the primary domain controller address if it has been

set.
NO
BACKUP DOMAIN CONTROLLER
Shows the backup domain controller address if it has been

set.
NO
LOGON USER NAME
Shows the logon user name of this equipment for the

domain if it has been set.
NO
PRIMARY WINS SERVER
Shows the primary WINS server address if it has been set.
NO
SECONDARY WINS SERVER
Shows the secondary WINS server address if it has been

set.
NO
SMB SIGNING OF SMB SERVER
Shows the setting of the SMB Signing of SMB Server.
NO
SMB SIGNING OF SMB CLIENT
Shows the setting of the SMB Signing of SMB Client.
NO
NETWORK SETTING - SESSION - NETWARE SESSION

Function
ENABLE BINDERY
192
List Print Format
Description
Shows whether the bindery mode is enabled or disabled.
User
NO
4 APPENDIX
4.APPENDIX
NETWORK SETTING - SESSION - NETWARE SESSION

Function
Description
User
ENABLE NDS
Shows whether the NDS mode is enabled or disabled.
NO
CONTEXT
Shows the NDS context.
NO
TREE
Shows the NDS tree.
NO
SEARCH ROOT
Shows the NDS Search Root.
NO
NETWORK SETTING - SESSION - BONJOUR SESSION

Function
Description
User
ENABLE BONJOUR
Shows whether Bonjour is enabled or disabled.
NO
LINK-LOCAL HOST NAME
Shows the link-local host name of this equipment for

Bonjour.
NO
SERVICE NAME
Shows the service name of this equipment for Bonjour.
NO
NETWORK SETTING - SESSION - LLTD SESSION

Function
Description
User
LLTD ENABLE
Shows whether the LLTD (Link Layer Topology Discovery)

protocol is enabled or disabled.
NO
DEVICE NAME
Shows the device name displayed on the Network Map.
NO
NETWORK SETTING - NETWORK SERVICE - HTTP NETWORK SERVICE

Function
Description
User
ENABLE HTTP SERVER
Shows whether the HTTP network service is enabled or

disabled.
NO
PRIMARY PORT NUMBER
Shows the primary port number for the HTTP network

service.
NO
SECONDARY PORT NUMBER
Shows the secondary port number for the HTTP network

service.
NO
ENABLE SSL
Shows whether the SSL for the HTTP network service is

NO
SSL PORT NUMBER
Shows the SSL port number for the HTTP network service.
NO
NETWORK SETTING - NETWORK SERVICE - SMTP CLIENT NETWORK SERVICE

Function
Description
User
ENABLE SMTP CLIENT
Shows whether the SMTP client is enabled or disabled.
NO
AUTHENTICATION
Shows whether SMTP authentication is enabled or

disabled.
NO
POP BEFORE SMTP
Shows whether POP Before SMTP is enabled or disabled.
NO
SMTP SERVER ADDRESS
Shows the IP address of the SMTP server that has been

assigned.
NO
LOGIN NAME
Shows the login name used for SMTP authentication.
NO
PORT NUMBER
Shows the port number to be used for sending an e-mail or

Internet Fax to the SMTP server.
NO
ENABLE SSL
Shows whether the SSL for the SMTP client is enabled or

disabled.
NO
List Print Format
193
4 APPENDIX
NETWORK SETTING - NETWORK SERVICE - SMTP SERVER NETWORK SERVICE

Function
Description
User
ENABLE SMTP SERVER
Shows whether the SMTP server is enabled or disabled.
NO
PORT NUMBER
Shows the port number to be used for receiving Internet

Faxes using the SMTP protocol.
NO
ENABLE OFFRAMP GATEWAY
Shows whether the offramp gateway is enabled or

disabled.
NO
ENABLE OFFRAMP SECURITY
Shows whether offramp security is enabled or disabled.
NO
ENABLE OFFRAMP PRINT
Shows whether offramp print is enabled or disabled.
NO
E-MAIL ADDRESS
Shows the e-mail address of this equipment if the SMTP

server is enabled and it has been set.
NO
NETWORK SETTING - NETWORK SERVICE - POP3 NETWORK SERVICE

Function
Description
User
ENABLE POP3 CLIENT
Shows whether the POP3 client is enabled or disabled.
NO
POP3 SERVER ADDRESS
Shows the IP address of the POP3 server if it has been

assigned.
NO
AUTHENTICATION
Shows whether POP3 authentication is enabled or

disabled.
NO
TYPE POP3 LOGIN
Shows the POP3 login type.
NO
ACCOUNT NAME
Shows the POP3 account name if it has been set.
NO
SCAN RATE
Shows the scan rate to check the POP3 server for new
messages (in minutes).
NO
PORT NUMBER
Shows the port number to be used for accessing the POP3

server.
NO
ENABLE SSL
Shows whether the SSL for the POP3 network service is

NO
SSL PORT NUMBER
Shows the SSL port number to be used for accessing the

POP3 server.
NO
NETWORK SETTING - NETWORK SERVICE - FTP CLIENT NETWORK SERVICE

Function
DEFAULT PORT NUMBER
Description
Shows the default port number to be used for saving a
document to the network folder using FTP.
User
NO
NETWORK SETTING - NETWORK SERVICE - FTP SERVER NETWORK SERVICE

Function
Description
User
ENABLE FTP SERVER
Shows whether the FTP server service is enabled or

disabled.
NO
DEFAULT PORT NUMBER
Shows the default port number to be used for receiving

data using FTP.
NO
ENABLE SSL
Shows whether SSL for the FTP network service is enabled

or disabled.
NO
SSL PORT NUMBER
Shows the SSL port number to be used for accessing the

FTP server.
NO
NETWORK SETTING - NETWORK SERVICE - SNMP NETWORK SERVICE

Function
ENABLE SNMP V1/V2
194
List Print Format
Description
Shows whether SNMP is enabled or disabled.
User
NO
4 APPENDIX
4.APPENDIX
NETWORK SETTING - NETWORK SERVICE - SNMP NETWORK SERVICE

Function
Description
User
READ COMMUNITY
Shows the read community name.
NO
ENABLE SNMP V3
Shows whether the SNMP V3 is enabled or disabled.
NO
ENABLE SNMP V3 TRAP
Shows whether the SNMP V3 trap is enabled or disabled.
NO
ENABLE AUTHENTICATION TRAP
Shows whether the authentication trap is enabled or

disabled.
NO
ENABLE ALERTS TRAP
Shows whether the alerts trap is enabled or disabled.
NO
IP TRAP ADDRESS1
Shows the IP address that has been set for IP trap address
1.
NO
IP TRAP COMMUNITY
Shows the IP Trap community name.
NO
IPX TRAP ADDRESS
Shows the IPX trap address.
NO
NETWORK SETTING - NETWORK SERVICE - SNTP NETWORK SERVICE

Function
Description
User
ENABLE SNTP
Shows whether SNTP is enabled or disabled.
NO
PRIMARY SNTP ADDRESS
Shows the primary SNTP server address if it has been set.
NO
SECONDARY SNTP ADDRESS
Shows the secondary SNTP server address if it has been

set.
NO
PORT NUMBER
Shows the port number to be used for accessing the SNTP

server.
NO
SCAN RATE
Shows the scan rate to check the SNTP server for adjusting
the time setting.
NO
NETWORK SETTING - NETWORK SERVICE - WEB SERVICES SETTING

Function
Description
User
FRIENDLY NAME
Shows the display name of this equipment.
NO
WEB SERVICES PRINT
Shows whether Web Service print is enabled or disabled.
NO
PRINTER NAME
Shows the printer name of this equipment.
NO
PRINTER INFORMATION
Shows the printer information of this equipment.
NO
WEB SERVICES SCAN
Shows whether Web Service scan is enabled or disabled.
NO
SCANNER NAME
Shows the scanner name of this equipment.
NO
SCANNER INFORMATION
Shows the scanner information of this equipment.
NO
NETWORK SETTING - NETWORK SERVICE - FILTERING

Function
Description
User
ENABLE IP FILTERING
Shows whether the IP filtering is enabled or disabled.
NO
ENABLE MAC ADDRESS FILTERING
Shows whether the MAC address filtering is enabled or

disabled.
NO
NETWORK SETTING - PRINT SERVICE SETTING - RAW TCP PRINT

Function
Description
User
ENABLE RAW TCP
Shows whether Raw TCP printing is enabled or disabled.
NO
PORT NUMBER
Shows the port number to be used for Raw TCP printing.
NO
List Print Format
195
4 APPENDIX
NETWORK SETTING - PRINT SERVICE SETTING - LPD PRINT

Function
Description
User
ENABLE LPD
Shows whether LPR printing is enabled or disabled.
NO
PORT NUMBER
Shows the port number to be used for LPR printing.
NO
BANNERS
Shows whether a banner will be printed for each LPR print

job.
NO
NETWORK SETTING - PRINT SERVICE SETTING - IPP PRINT

Function
Description
User
ENABLE IPP
Shows whether IPP printing is enabled or disabled.
NO
ENABLE PORT80
Shows whether Port80 is used for IPP printing.
NO
PORT NUMBER
Shows the port number to be used for IPP printing.
NO
URL
Shows the URL for IPP printing.
NO
ADMINISTRATORS NAME
Shows the administrators user name allowed to perform

the [Cancel All Documents] function.
NO
AUTHENTICATION
Shows whether the authentication for IPP printing is

NO
USER NAME
Shows the user name for authentication.
NO
ENABLE SSL
Shows whether SSL for IPP printing is enabled or disabled.
NO
SSL PORT NUMBER
Shows the SSL port number to be used for IPP printing.
NO
SSL URL
Shows the SSL URL for IPP printing.
NO
NETWORK SETTING - PRINT SERVICE SETTING - FTP PRINT

Function
Description
User
ENABLE FTP PRINT
Shows whether FTP printing is enabled or disabled.
NO
PRINT USER NAME
Shows the user name for FTP printing.
NO
PRINT PASSWORD
Shows the password for FTP printing.
NO
PORT NUMBER
Shows the port number to be used for FTP printing.
NO
NETWORK SETTING - PRINT SERVICE SETTING - NETWARE PRINT

Function
Description
User
LOGIN NAME
Shows the login name for the NetWare file server.
NO
PASSWORD
Shows the password for the NetWare file server.
NO
PRINT QUEUE SCAN RATE
Shows how often the equipment scans the queue on

NetWare file server (in second).
NO
NETWORK SETTINGS - PRINT AND NOTIFICATION SERVICE - E-MAIL PRINT

Function
196
Description
User
ENABLE PRINT HEADER
Shows whether the header will be printed or not for e-mail

printing.
NO
ENABLE PRINT MESSAGE BODY
Shows whether the message body will be printed or not for

e-mail printing.
NO
MAXIMUM E-MAIL BODY PRINT
Shows the maximum number of pages to print the body

strings of the received e-mail print job.
NO
ENABLE PRINT E-MAIL ERROR
Shows whether an e-mail error report will be printed or not.
NO
List Print Format
4 APPENDIX
4.APPENDIX
NETWORK SETTINGS - PRINT AND NOTIFICATION SERVICE - E-MAIL PRINT

Function
Description
User
ENABLE E-MAIL ERROR FORWARD
Shows whether an e-mail error message will be sent or not.
NO
E-MAIL ERROR TRANSFER ADDRESS
Shows the e-mail address to which an e-mail error

message will be sent if it is to be set.
NO
ENABLE PARTIAL E-MAIL
Shows whether the equipment allows printing an e-mail job

that is partially received.
NO
PARTIAL WAIT TIME
Shows how long the equipment will wait to receive data for
a partial e-mail job before printing (in seconds).
NO
MDN REPLY
Shows whether MDN Reply is enabled or disabled.
NO
List Print Format
197
4 APPENDIX
PS3 font list

Output example of the PS3 Font List
198
List Print Format
4 APPENDIX
4.APPENDIX
PCL font list

Output example of the PCL Font List
List Print Format
199
INDEX
Numerics
[1200dpi PRINT] ........................................................82
2ND TEL ...................................................................32
[600dpi PRINT] ..........................................................82
A
ACS ADJUSTMENT ............................................ 18, 21
[ADDRESS BOOK] ....................................................25
ADDRESS BOOK EDIT ..............................................35
Address Book Information ...........................................24
Address book information .........................................180
ADDRESS BOOK REGISTRATION .............................31
ADDRESS MODE .........................................88, 89, 90
MANUAL ...............................................................92
STATEFUL ............................................................97
STATELESS ..........................................................94
ADDRESS SEARCH ..................................................40
ADMIN
Changing user password .......................................135
COPY ..................................................................118
E-MAIL ................................................................123
FAX .....................................................................120
FILE ....................................................................122
GENERAL .............................................................65
IEEE 802.1X Authentication ...................................136
INTERNET FAX ....................................................124
LIST/REPORT ............................................. 127, 132
NETWORK ............................................................87
SECURITY ...........................................................125
[ADMIN] tab ..............................................................63
[ADMIN. MESSAGE] ..................................................66
[ALL LIMIT] .............................................................173
[APPLETALK] ..........................................................104
Authority
ACCESSIBILITY ...................................................126
CHANGE .............................................................126
EXTRACT ............................................................126
PRINT .................................................................126
AUTO 2-SIDE MODE ...............................................118
[AUTO CLEAR] ............................................................9
Auto clear mode ..........................................................9
[AUTO POWER SAVE] ...............................................74
Auto power save mode ...............................................72
Auto-IP .....................................................................88
AUTOMATIC CHANGE OF PAPER SOURCE ... 119, 133
B
B/W ADJUSTMENT IN ACS ........................................21
BACKGROUND ADJUSTMENT ..................................21
[BODY] .......................................................... 123, 124
Body String Transmission .........................................124
C
[CALIBRATION] .................................................. 14, 80
[CHANGE LANGUAGE] .............................................10
[CHANGE USER PASSWORD] ........................ 135, 175
Change user password .............................................175
[CHAP] ...................................................................147
CHAP .....................................................................136
[CHECK E-MAIL] .......................................................58
CHECK OF GROUP MEMBER ............................ 44, 46
[CHECK SETTINGS] ................................................137
[CLOCK] ...................................................................70
COLOR MODE ................................................... 16, 20
[COMM. REPORT] ...................................................129
Communication report ..............................................127
COMPRESS ............................................................. 20
[CONTACT INFORMATION] ...................................... 66
Contacts
Deleting ................................................................ 36
Editing .................................................................. 34
Registering ............................................................ 30
Searching .............................................................. 38
[CONTENTS] ............................................................ 57
[CONTEXT] ............................................................ 101
[COPY] .................................................................... 16
Copy calibration ........................................................ 81
CORP. ..................................................................... 32
COUNTER MENU ................................................... 151
D
[DATE FORMAT] ...................................................... 71
[DATE/TIME] ............................................................ 70
DEFAULT MODE OF AUTO COLOR ........................ 119
[DELETE ALL] ........................................................ 165
Department Code
Registering .......................................................... 166
Department code
Deleting ...................................................... 165, 171
Editing ................................................................ 168
Enabling .............................................................. 163
Printing ............................................................... 162
Resetting all counters ........................................... 164
Resetting counter ................................................. 172
Department code list ............................................... 179
[DEPARTMENT COUNTER] .................................... 156
Department counter ................................................. 156
[DEPARTMENT MANAGEMENT] ..................... 160, 163
[DEPARTMENT REGISTRATION] ............166, 168, 171
DEPT. ...................................................................... 32
[DESIRED ZONE] ................................................... 105
[DEVICE INFORMATION] .......................................... 65
[DEVICE NAME] ..................................................... 105
DHCP (IP Address) ............................................. 95, 97
DHCP (OPTIONS) ........................................93, 95, 97
DHCP Server ............................................................ 88
DIRECT TX ............................................................ 129
DISABLE FILE SHARE ............................................ 103
DISABLE PRINT SHARE ......................................... 103
Discard Print ........................................................... 120
[DISPLAY LEVEL] ..................................................... 76
[DISPLAY SETTING] ................................................. 13
[DRAWER] ............................................................... 27
DRAWER SET .......................................................... 77
[DYNAMIC] .............................................................. 88
E
[EAP-MD5] ............................................................. 139
EAP-MD5 ....................................................... 136, 148
[EAP-MSCHAPv2] ...................................138, 142, 144
EAP-MSCHAPv2 .................................................... 136
[EAP-TLS] .............................................................. 140
EAP-TLS ................................................................ 136
[EAP-TTLS] ............................................................ 143
EAP-TTLS .............................................................. 136
[EAP-User Name]
................138, 139, 140, 142, 144, 146, 147, 149
[E-FILING] ................................................................ 23
[E-MAIL] ................................................................... 67
E-MAIL .................................................................... 32
ENABLE APPLETALK ............................................. 105
ENABLE BINDERY ................................................. 101
INDEX
201
ENABLE HTTP SERVER ..........................................107

ENABLE IPX/SPX ......................................................99
ENABLE NDS ..........................................................101
ENABLE SSL ..........................................................107
Encryption Level
128bit AES ...........................................................126
128bit RC4 ...........................................................126
40bit RC4 .............................................................126
[ENERGY SAVER] .....................................................72
[ETHERNET] ...........................................................108
EXPOSURE ....................................................... 19, 21
EXPOSURE FOR BLACK ...........................................16
EXPOSURE FOR COLOR ..........................................16
F
[FACTORY DEFAULT]
IEEE802.1X authentication ....................................137
IPsec ...................................................................112
FALL BACK MODE ..................................................137
[FAX] ........................................................................19
[FAX COMMUNICATION] .........................................159
FAX NO. ...................................................................32
FIRST NAME ............................................................32
[FLUSH CONNECTIONS] .........................................112
Forced Encryption ....................................................126
FRAGMENT MESSAGE SIZE ...................................123
FRAGMENT PAGE SIZE ..........................................124
Fragmentation ................................................ 123, 124
FRAME TYPE ...........................................................99
[FROM ADDRESS] ......................................... 123, 124
[FROM NAME] ............................................... 123, 124
[FUNCTION] .............................................................26
FUNCTION .............................................................132
Function List (Administrator) ......................................184
Function List (User) ....................................................24
Function list (User) ...................................................182
Group Numbers Information ....................................... 24

GROUP SEARCH ..................................................... 55
H
[HTTP] ................................................................... 106
I
[ID SORT] ................................................................ 25
[IEEE802.1X SETTING] ........................................... 136
IMAGE DIRECTION .................................................. 16
IMAGE QUALITY FOR BLACK IN ACS ....................... 21
INITIAL PREVIEW TYPE ........................................... 21
Inner authentication
CHAP ................................................................. 147
EAP-MD5 ............................................................ 148
EAP-MSCHAPv2 ................................................. 144
PAP .................................................................... 145
INTERNET PROTOCOL .......................................... 103
[IP ADDRESS] .......................................................... 93
IP ADDRESS ............................................................ 90
IP Filtering .............................................................. 110
[IPsec] ................................................................... 112
[IPv4] ....................................................................... 88
[IPv6] ...........................................................92, 94, 96
IPv6 Protocol ................................................92, 94, 97
[IPX/SPX] ................................................................. 98
J
[JOB STATUS] ......................................................... 33
JOURNAL .............................................................. 128
K
KEEP CONFIGURATION .......................................... 95
KEYWORD .............................................................. 32
[KNOWN ID] ....................................................... 48, 53
KNOWN ID ............................................................... 38
[GATEWAY] ..............................................................93
Gateway ...................................................................90
GENERAL
Administrator password ...........................................68
Auto clear ................................................................9
Calibration ...................................................... 14, 79
Change language ...................................................10
Date and time .........................................................70
Device information ..................................................65
Display contrast ......................................................12
Display level ...........................................................76
Energy saver mode .................................................72
Notification .............................................................66
Panel calibration .....................................................85
Pop-up message ....................................................77
Registration ..................................................... 15, 84
Reversed display mode ...........................................11
Status Message ......................................................78
Group
Creating .................................................................42
Deleting .................................................................51
Editing ...................................................................45
Searching ..............................................................52
[GROUP NAME] ...........................................43, 46, 55
GROUP NO. EDIT .....................................................45
GROUP NO. REGISTRATION ....................................43
Group number information ........................................181
[GROUP NUMBERS] .................................................26
LAST NAME ............................................................. 32

LDAP (Lightweight Directory Access Protocol) ........... 110
Link Local Address ........................................92, 94, 97
[LIST] ............................................................... 24, 132
LLMNR ........................................................92, 94, 97
LOCAL ................................................................... 131
[LOCATION] ............................................................. 66
[LOG] tab ................................................................. 33
LOGON ................................................................. 103
202
INDEX
M
MAC ADDRESS FILTERING .................................... 110
[MASTER PASSWORD] .......................................... 126
MAXIMUM COPIES ................................................ 118
Message Properties ........................................ 123, 124
N
[NAME SORT] .......................................................... 25
NetBIOS NAME ...................................................... 103
[NETWARE] ........................................................... 100
NETWORK
AppleTalk protocol ............................................... 104
Ethernet speed .................................................... 108
HTTP network service .......................................... 106
IPsec .................................................................. 111
IPv6 protocol ......................................................... 91
IPX/SPX protocol ................................................... 98
LDAP/SNMP network services

and Filtering functions ...........................................109
NetWare Settings ..................................................100
Network check ......................................................115
SMB protocol ........................................................102
TCP/IP protocol (IPv6) .............................................87
User certificate .....................................................113
[NETWORK CHECK] ...............................................115
NIC CONFIGURATION PAGE ...................................132
NIC configuration page .............................................183
[NO AUTO IP] ............................................................89
[NO LIMIT BLACK] ...................................................174
[NOTIFICATION] .......................................................67
O
[OLD PASSWORD] ....................................................69
OMIT BLANK PAGE ADJUSTMENT ..................... 18, 21
ORIGINAL MODE ............................................... 19, 21
ORIGINAL MODE FOR AUTO COLOR ........................18
ORIGINAL MODE FOR BLACK ...................................17
ORIGINAL MODE FOR COLOR ..................................17
[OTHER] .................................................................110
Output limitations .....................................................173
P
[PANEL CALIBRATION] .............................................85
[PAP] ......................................................................145
PAP ........................................................................136
PAPER JAM RECOVERY ...........................................77
PAPER OF DIFFERENT DIRECTION ............... 119, 133
[PASSWORD SETUP] ................................................68
PCL FONT LIST ......................................................132
PCL font list .............................................................199
[PEAP] ....................................................................142
PEAP .....................................................................136
POLICY NAME ........................................................112
POLLING ................................................................129
[POP-UP] ..................................................................77
[PREFIX] ...................................................................93
PREVIEW SETTING ..................................................21
[PRIMARY PORT NUMBER] .....................................107
[PRINT] ....................................................................82
Print calibration ..........................................................82
[PRINT COUNTER] ......................................... 153, 157
[PRINT OUT DEPARTMENT CODES] .......................162
[PRINT OUT TOTAL COUNTER] ...............................155
PRINTER/E-FILING .................................................133
PRINTING IMAGE MODE ...........................................23
Printing out total counter ...........................................155
PS3 FONT LIST ......................................................132
PS3 font list .............................................................198
R
[RECEIVE] ................................................................33
Reception journal .....................................................127
[RECEPTION LIST] ..................................................130
Reception list ...........................................................127
Reduction Print ........................................................120
[REGISTRATION] ............................................... 15, 84
RELAY DESTINATION .............................................130
RELAY ORIGINATOR ..............................................130
RELAY STATION ........................................... 130, 131
REMOTE ................................................................131
[REPORT SETTING] ................................................127
[RESET ALL COUNTERS] ........................................164
[RESET COUNTERS] ..............................................172
RESOLUTION .................................................... 19, 21

[REVERSED DISPLAY] ............................................. 11
ROTATION .............................................................. 20
RX JOURNAL ......................................................... 128
[RX PRINT] ............................................................ 120
RX Print ................................................................. 120
S
[SCAN] .............................................................. 20, 33
[SCAN COUNTER] ......................................... 154, 158
[SEARCH] ....................................................40, 49, 55
[SEARCH ROOT] .................................................... 101
[SECONDARY PORT NUMBER] .............................. 107
[SEND] .................................................................... 33
[SERVICE PHONE NUMBER] .................................... 66
SINGLE/2-SIDE SCAN .............................................. 20
[SLEEP MODE] ........................................................ 75
Sleep mode .............................................................. 72
[SMB] .................................................................... 102
SMB PROTOCOL ................................................... 103
[SNMP READ COMMUNITY] ................................... 110
SORT MODE PRIORITY ......................................... 118
[STATIC] .................................................................. 90
Static IP Address ...................................................... 90
[STATUS MESSAGE] ................................................ 78
Storage maintenance .............................................. 122
Subnet mask ............................................................ 90
SUSPEND PRINTING IF STAPLER EMPTY ...... 119, 133
T
[TOTAL COUNTER] ................................................ 152
Total counter list ..................................................... 178
Transmission journal ............................................... 127
[TREE] ................................................................... 101
TX JOURNAL ......................................................... 128
U
USE AUTHENTICATION CODE AS PASSWORD ...... 126
Use Username from Common Name
in the User Certificate ........................................... 140
USER
ADDRESS BOOK .................................................. 30
CHECK E-MAIL ..................................................... 58
COPY ................................................................... 16
DRAWER .............................................................. 27
E-FILING .............................................................. 23
FAX ...................................................................... 19
GENERAL ............................................................... 9
LIST ..................................................................... 24
SCAN ................................................................... 20
[USER CERTIFICATE] ............................................ 113
[USER PASSWORD] ............................................... 126
[USER] tab ................................................................. 8
W
[WEEKLY TIMER] ..................................................... 73
Weekly timer ............................................................ 72
WINS PRIMARY ..................................................... 103
WINS SECONDARY ............................................... 103
INDEX
203
204
INDEX
FC-5520C/6520C/6530C
FC-2330C/2820C/2830C/3520C/3530C/4520C
OME080017B0
MULTIFUNCTIONAL DIGITAL SYSTEMS

MFP Management Guide
2-17-2, HIGASHIGOTANDA, SHINAGAWA-KU, TOKYO, 141-8664, JAPAN
2008 TOSHIBA TEC CORPORATION All rights reserved
R071220F0002-TTEC
Ver02 2008-10

Toshiba 2820C MFP Management Guide

Uploaded by

Copyright:

Available Formats

Toshiba 2820C MFP Management Guide

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Toshiba 2820C MFP Management Guide

Uploaded by

Copyright:

Available Formats

MULTIFUNCTIONAL DIGITAL SYSTEMS

MFP Management Guide

2008 TOSHIBA TEC CORPORATION All rights reserved

How to read this manual

SETTING ITEMS (USER)

SETTING ITEMS (ADMIN)

IPsec (IP security) setting.................................................................................................. 111

MANAGING COUNTERS (COUNTER MENU)

PS3 font list ....................................................................................................................... 198

SETTING ITEMS (USER)

Entering User Menu ................................................................................................................. 8

Setting Copy Functions ......................................................................................................... 16

Checking E-mail ..................................................................................................................... 58

1 SETTING ITEMS (USER)

Entering User Menu

Press the [USER] tab.

Continue the user setting operation that you require.

The USER menu is displayed.

P.9 Setting General Functions

Entering User Menu

1 SETTING ITEMS (USER)

Setting General Functions

Press [GENERAL] in the USER menu.

The GENERAL menu is displayed.

To display the USER menu, see the following page:

Press [AUTO CLEAR].

The AUTO CLEAR screen is displayed.

Press the button that indicates the desired time in seconds.

Setting General Functions

1 SETTING ITEMS (USER)

Changing the display language

Press [GENERAL] in the USER menu.

The GENERAL menu is displayed.

To display the USER menu, see the following page:

Press [CHANGE LANGUAGE].

The CHANGE LANGUAGE screen is displayed.

Press the desired language button.

The touch panel is displayed in the selected language.

Setting General Functions

1 SETTING ITEMS (USER)

Setting the reversed display mode

Press [GENERAL] in the USER menu.

The GENERAL menu is displayed.

To display the USER menu, see the following page:

Press [REVERSED DISPLAY].

The REVERSED DISPLAY screen is displayed.

Setting General Functions

1 SETTING ITEMS (USER)

Adjusting the display contrast

Press [GENERAL] in the USER menu.

The GENERAL menu is displayed.

To display the USER menu, see the following page:

Setting General Functions

1 SETTING ITEMS (USER)

Press [DISPLAY SETTING].

The DISPLAY SETTING menu is displayed.

Adjust the touch panel contrast.

to brighten the touch panel display. Use

to darken the touch panel display.

Setting the calibrations