Circuit Maker

Basic Tutorial of Circuit Maker
Introduction
In this course, we will be using the free student edition of a commercial program,
CircuitMaker, to design and simulate logic circuits.
Starting a New Design

This program is user-friendly and well designed, but it is not something that you
can just pick up and start using without some trial and error on part of the user, or
with some kind of instruction. This is because it assumes you already know how
to design digital logic circuits, and does not provide any tutorial material.
Next we give you some pointers in order to help you get started and to avoid
some common problems. There is also some help that comes with the program,
but it tends to be sketchy.
1. The first thing to observe is that CircuitMaker can be used to design and
simulate both analog and digital signals. (Wherever you see "Spice" in the
help system, it's talking about analog simulation.) You can build your
circuit with out concern for this fact, but when you simulate it (run it), you
must be sure to do so in digital mode. If you don't, you'll get an error
message, probably telling you that you need a ground node "before a valid
spice Netlist can be generated". To avoid this problem click on the toolbar
button with the symbol for a transistor on it (shown in the next figure).
Just get in the habit of clicking on the transistor button (it turns into an
AND gate) every time you start running CircuitMaker.
2. If you care about the neatness of your diagrams, select Grid (1) under the
Options menu, and select the "Snap to grid" option.
3. Use the Devices menu (2) to select gates, etc. to add to your circuit. Use
the Wire Tool (3) to connect inputs and outputs together.
3
4. The most common input device is the digital logic switch, which alternates
between outputting 0 and 1 each time you click on in. You can type a
lower-case 's' to get one, or look for it in Hotkeys2 under the Devices
menu, or select browse from the Devices menu, and select Digital ->
Power.
5. You can simulate your circuit one step (or propagation delay) at a time (4),
or let it run at "full speed" (5.) Either way, you can use the probe tool (6) to
look at the logic value of any part of your circuit. The probe will show H
("high"), L ("low"), or Z (indeterminate) as you make it hover over various
parts of the circuit.
4 5 6
6. Sometimes, you will want to look at the waveforms for various parts of the
circuit as you run your simulations. Use F12 to turn this option on, or press
the waveform toolbar button (7). The waveforms are displayed in a
separate window, so select "tile" from the Window menu to get them both
to show on the screen.
7. The most common way to add traces to the waveforms window is to
attach the Scope (8) tool to the wires you want to look at. Type a capital T
to get a Scope tool, or select it from the Hotkeys2 menu under the Devices
menu. To give meaningful names to your waveforms, double-click on the
scope tool and type in the name you want to use.
8. You can move waveforms up and down by dragging their names in the
waveforms window. The white boxes (9) to the left of the names are used
for setting breakpoints. Breakpoints can be used to stop the simulation
when the certain conditions are met. You can learn how to use
breakpoints from the on-line help.
9. To generate input values automatically or to have a clock signal, you have

to generate them using a Data Sequencer (10). Type capital G to get one,
or browse to it under Digital/Instruments under the Devices menu. Here's
how to set it up so that pins 1-3 on the right side can be used as an inputs
signals.
10
Double click on the device, and you will get an "Edit Data Sequencer"
dialog box. First of all, resist the temptation to turn on the "Use External
Clock" option; it generates values at the proper rate for simulation (one
propagation delay per step) all by itself. The data sequencer can generate
up to 8 digital input signals with up to 32 different sequences. Each input

sequence is stored in an address. For example, Edit the first 8 rows of the
"Address - Data" box so that addresses 1, 2, 3, 4 contain 00
(hexadecimal), and addresses 5, 6, 7, 8 contain 01. Set the Start and Stop
Addresses to 1 and 8 respectively.
When the simulation runs, the sequencer will output 000 on pins Nos. 13 for four propagation delays, then will output 001 on the same pins for
another four propagation delays, and so on. The process repeats as long
as the simulation runs. For example, connect scopes to the signals you
want to check out, and display their respective waveforms in the waveform
window.
10. Use the Digital Options dialog box to control the size of a step when
running the simulation in single step mode, to set the conditions for break
points and to set the simulation speed. Choose Simulation > Digital to
display the dialog box.
You can define the Step Size in either ticks or cycles. A cycle always
consists of 10 ticks. A tick is the smallest unit of delay for the digital
simulator. It takes one tick to perform a single step of the simulation for all
devices.
Adjust X Magnification to view a larger or smaller section of the waveforms

in the digital Waveforms window. By default, the magnification is set to 8.
A smaller value zooms out, a greater value zooms in.
Use Simulation Speed to control how fast the simulation runs. This could
be useful, for example, if the simulation is running too fast to view the
states of a seven-segment display. Setting this field to a lower number
slows down the simulation so you can view the changes of the display.
Another method of slowing the simulation would be to run it in single step
mode or set breakpoints.
Use the Breakpoint and Conditions options in conjunction with the
waveforms window to set breakpoints. The following table illustrates the
results of various combinations of settings.
Combination Result
Level-And
All break conditions must be met before the simulation stops.
Level-Or
Any one of the break conditions stops the simulation.
Edge-And
The simulation stops when the proper edge occurs on all of
the specified waveforms.

Edge-Or
The simulation stops if a transition to any of the specified
conditions occurs.

Circuit Maker

Uploaded by

Copyright:

Available Formats

Circuit Maker

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Circuit Maker

Uploaded by

Copyright:

Available Formats

Basic Tutorial of Circuit Maker

Starting a New Design

9. To generate input values automatically or to have a clock signal, you have

up to 8 digital input signals with up to 32 different sequences. Each input

Adjust X Magnification to view a larger or smaller section of the waveforms

All break conditions must be met before the simulation stops.

Any one of the break conditions stops the simulation.

The simulation stops when the proper edge occurs on all of

the specified waveforms.

The simulation stops if a transition to any of the specified

You might also like