Group 2 and 3 - Lab 4

Lab Assignment: 4
INWK 6117
Group 2
Vignesh Puli Janardhanan (B00567154)
Alagappan Vairavan (B00566817)
Kanika Poply (B00558593)
Group 3
Srinivas Yadalla (B00564873)
Vignesh Murali (B00571459)
Srinath Jayraman (B00561608)
1. Enable debugging on each router and show the output:
2. Show ip route. Discuss the output?

We can see all four loopbacks in 9R4 routing table.
3. Show ip route < loopback of YR4/XR4> on YR4/XR4. Discuss the output?

It displays the route to 172.16.3.3 from 9R4 i.e. 172.16.2.2
4. Show mpls traffic-eng tunnels. Discuss the output?

This command displays the explicit route followed and information about the tunnel
running from 172.16.1.1 to 172.16.4.4.
5. Show mpls traffic-eng tunnels brief. Discuss the output.

It shows that LSP tunnels are running from 9R1 to 10R1
6. Ping from 10R2 to 9R2

10R2#ping
Protocol [ip]:
Target IP address: 10.1.3.3
Repeat count [5]:
Datagram size [100]:
Timeout in seconds [2]:
Extended commands [n]: y
Source address or interface: 10.1.21.2
Type of service [0]:
Set DF bit in IP header? [no]:
Validate reply data? [no]:
Data pattern [0xABCD]:
Loose, Strict, Record, Timestamp, Verbose[none]:
Sweep range of sizes [n]:
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.3.3, timeout is 2 seconds:
Packet sent with a source address of 10.1.21.2
!!!!!
Ping from 9R2 to 10R2

9r2#ping
Protocol [ip]:
Repeat count [5]:
Datagram size [100]:
Extended commands [n]: y
Source address or interface: 10.1.2.2
Type of service [0]:
Set DF bit in IP header? [no]:
Validate reply data? [no]:
Data pattern [0xABCD]:
Sweep range of sizes [n]:
Sending 5, 100-byte ICMP Echos to 10.1.3.3, timeout is 2 seconds:
Packet sent with a source address of 10.1.2.2
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
9r2#
7. Trace route from tunnel head to tunnel end and also the vice versa?
9r2#traceroute
Protocol [ip]:

Source address: 10.1.2.2
Numeric display [n]:
Probe count [3]:
Minimum Time to Live [1]:
Maximum Time to Live [30]:
Port Number [33434]:
Tracing the route to 10.1.3.3
1
2
3
4
5
10.1.12.1 0 msec 0 msec 0 msec

192.168.14.4 0 msec 0 msec 4 msec
192.168.44.14 0 msec 0 msec 4 msec
192.168.41.1 0 msec 0 msec 4 msec
10.1.21.2 0 msec 0 msec *
10R2#traceroute
Protocol [ip]:
Probe count [3]:
1 10.1.21.1 0 msec 0 msec 0 msec

2 192.168.141.4 0 msec 0 msec 0 msec
3 192.168.14.1 4 msec 0 msec 0 msec
4 10.1.12.2 4 msec 0 msec *
Trace route for explicitly defined path:

10R2#traceroute
Protocol [ip]:
Probe count [3]:
1 10.1.21.1 0 msec 0 msec 0 msec

2 192.168.41.4 0 msec 0 msec 4 msec
3 192.168.44.4 0 msec 0 msec 4 msec
4 192.168.14.1 0 msec 0 msec 4 msec
5 10.1.12.2 0 msec 0 msec *
8. Submit running configuration of all the routers?

Running Configuration on 9S1
9S1(config)#do show run
Building configuration...
Current configuration : 1841 bytes

!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname 9S1
!
!
no aaa new-model
system mtu routing 1500
vtp domain inwk
vtp mode transparent
ip subnet-zero
!
!
!
!
no file verify auto
spanning-tree mode pvst
spanning-tree extend system-id
!
vlan internal allocation policy ascending
!
vlan 2
name B
!
vlan 3
name C
!
vlan 4
name D
!
vlan 12,14
!
!
interface GigabitEthernet0/1
switchport access vlan 12
switchport mode access
!
!
shutdown
!
!
shutdown
!
shutdown
!
shutdown
!
!
shutdown
!
!
shutdown
!
!
!
!
!
!
!
!
!
!
!
!
!
shutdown
!
!
!
!
!
interface Vlan1
no ip address
!
ip classless
ip http server
!
!
control-plane
!
!
line con 0
line vty 5 15
!
!
monitor session 1 source vlan 1 rx
monitor session 1 destination interface Gi0/23
end
Running configuration on 10S1

10s1#sh run

!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
!
hostname 10s1
!
no logging console
!
no aaa new-model
system mtu routing 1500
vtp domain INWK

vtp mode transparent
ip subnet-zero
!
!
!
!
no file verify auto
spanning-tree mode pvst
spanning-tree extend system-id
!
vlan internal allocation policy ascending
!
vlan 2-4,21,41
!
!
!
!
shutdown
!

!
shutdown
!
shutdown
!
shutdown
!
shutdown
!
shutdown
!
shutdown
!
shutdown
!
!
shutdown
!
!
!
shutdown
!
shutdown
!
shutdown
!
shutdown
!
shutdown
!
shutdown
!
shutdown
!
shutdown
!
shutdown
!
shutdown
!
shutdown
!
shutdown
!
shutdown
!
interface Vlan1
no ip address
!
ip classless
ip http server
!
!
!
control-plane
!
!
line con 0
line vty 5 15
!
end
Running Configuration on 9R1

9R1#sh run
!
version 15.0
service timestamps debug datetime msec
service timestamps log datetime msec
!
hostname 9R1
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
!
!
!
!
!
!
no ipv6 cef
ip source-route
ip cef
!
!
!
!
!
multilink bundle-name authenticated
!
mpls traffic-eng tunnels
no mpls ip
!
!
!
!
voice-card 0
!
!
!
!
!
!
license udi pid C3900-SPE100/K9 sn FOC15074H97
hw-module pvdm 0/0
!
!
!
!
redundancy
!
!
!
!
!
!
!
!
!
interface Loopback0
ip address 172.16.1.1 255.255.255.255
!
!
interface Tunnel1
ip unnumbered Loopback0
tunnel mode mpls traffic-eng
tunnel destination 172.16.4.4
tunnel mpls traffic-eng autoroute announce
tunnel mpls traffic-eng priority 1 1
tunnel mpls traffic-eng bandwidth 6667
tunnel mpls traffic-eng path-option 1 explicit identifier 910
tunnel mpls traffic-eng path-option 2 dynamic
!
no routing dynamic
!
ip address 10.1.12.1 255.255.255.0
duplex auto
speed auto
mpls ip
!
!
no ip address
shutdown
duplex auto
speed auto
!
!
ip address 192.168.14.1 255.255.255.0
duplex auto
speed auto
mpls ip
!
ip rsvp bandwidth 100000
!
interface Serial0/0/0
no ip address
shutdown
no fair-queue
no clock rate 2000000
!
!
no ip address
shutdown
!
!
!
router ospf 1
mpls traffic-eng router-id Loopback0
mpls traffic-eng area 0
router-id 172.16.1.1
log-adjacency-changes
network 172.16.1.1 0.0.0.0 area 0
network 192.168.14.0 0.0.0.255 area 0
!
router bgp 1
no synchronization
bgp router-id 172.16.1.1
bgp log-neighbor-changes
neighbor 10.1.12.2 remote-as 10
neighbor 172.16.4.4 update-source Loopback0
neighbor 172.16.4.4 next-hop-self
no auto-summary
!
ip forward-protocol nd
!
no ip http server
no ip http secure-server
!
!
ip explicit-path identifier 910 enable
next-address 172.16.2.2
!
!
!
!
!
nls resp-timeout 1
cpd cr-id 1
!
!
control-plane
!
!
!
voice-port 0/1/0
!
voice-port 0/1/1
!
voice-port 0/2/0
!
voice-port 0/2/1
!
!
!
!
!
!
!
gatekeeper
shutdown
!
!
line con 0
line aux 0
line vty 0 4
login
!
scheduler allocate 20000 1000
end
9r2#sh run
!
version 12.4
!
hostname 9r2
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
!
resource policy
!
no network-clock-participate slot 2
ip subnet-zero
ip cef
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface Loopback0
ip address 10.1.2.2 255.255.255.255
!
ip address 10.1.12.2 255.255.255.0
duplex auto
speed auto
media-type rj45
negotiation auto
!
no ip address
shutdown
duplex auto
speed auto
media-type rj45
negotiation auto
!
interface Serial1/0
no ip address
shutdown
serial restart-delay 0
!
interface Serial1/1
no ip address
shutdown
!
interface Serial1/2
ip address 169.1.24.2 255.255.255.0
shutdown
!
interface Serial1/3
no ip address
shutdown
!
interface FastEthernet2/0
no ip address
shutdown
duplex auto
speed auto
!
no ip address
shutdown
duplex auto
speed auto
!
router bgp 10
no synchronization
network 10.1.2.2 mask 255.255.255.255
no auto-summary
!
ip classless
!
!
ip http server
!
!
!
!
!
control-plane
!
!
!
!
!
!
!
!
!
!
line con 0
stopbits 1
line aux 0
stopbits 1
line vty 0 4
login
!
!
end
9r2#

9R4#show run

!
version 12.4
!
hostname 9R4
!
boot-start-marker
boot-end-marker
!
logging buffered 4096 debugging
no logging console
!
no aaa new-model
!
resource policy
!
ip subnet-zero
ip cef
!
!
!
!
!
no mpls ip
voice-card 0
no dspfarm
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface Loopback0
ip address 172.16.2.2 255.255.255.255
!
ip address 192.168.44.4 255.255.255.0
duplex auto
speed auto
media-type rj45
negotiation auto
mpls ip
!
no ip address
shutdown
duplex auto
speed auto
media-type rj45
negotiation auto
!
no ip address
shutdown
duplex auto
speed auto
!
ip address 192.168.14.4 255.255.255.0
duplex auto
speed auto
mpls ip
!
bandwidth 155000
ip address 192.168.141.4 255.255.255.0
clock rate 2000000
!
no ip address
shutdown
clock rate 2000000
!
router ospf 1
router-id 172.16.2.2
network 172.16.2.2 0.0.0.0 area 0
network 192.168.14.0 0.0.0.255 area 0
network 192.168.44.0 0.0.0.255 area 0
network 192.168.141.0 0.0.0.255 area 0
!
ip classless
!
!
ip http server
!
!
!
!
!
control-plane
!
!
!
voice-port 0/1/0
!
voice-port 0/1/1
!
voice-port 0/2/0
!
voice-port 0/2/1
!
voice-port 0/3/0
!
voice-port 0/3/1
!
!
!
!
!
!
!
!
line con 0
stopbits 1
line aux 0
stopbits 1
line vty 0 4
login
!
!
End
Running configuration on 10R1

10R1#sh run

!
! Last configuration change at 14:58:28 UTC Tue May 8 2012
!
version 15.0
!
hostname 10R1
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
!
!
!
!
!
!
no ipv6 cef
ip source-route
ip cef
!
!
!
!
no ip domain lookup
!
multilink bundle-name authenticated
!
mpls label protocol ldp
!
!
!
!
voice-card 0
!
!
!
!
!
!
license udi pid C3900-SPE100/K9 sn FOC15032SEG
hw-module pvdm 0/0
!
!
!
!
redundancy
!
!
!
!
!
!
!
!
!
interface Loopback0
ip address 172.16.4.4 255.255.255.255
!
!
interface Tunnel1
ip unnumbered Loopback0
tunnel mode mpls traffic-eng
tunnel destination 172.16.1.1
tunnel mpls traffic-eng autoroute announce
tunnel mpls traffic-eng priority 1 1
tunnel mpls traffic-eng bandwidth 6667
tunnel mpls traffic-eng path-option 1 explicit identifier 1
tunnel mpls traffic-eng path-option 2 dynamic
!
no routing dynamic
!
ip address 10.1.21.1 255.255.255.0
duplex auto
speed auto
!
!
no ip address
shutdown
duplex auto
speed auto
!
!
ip address 192.168.41.1 255.255.255.0
duplex auto
speed auto
!
!
no ip address
shutdown
!
!
bandwidth 155000
ip address 192.168.141.1 255.255.255.0

!
!
!
router ospf 1
network 172.16.4.4 0.0.0.0 area 0
network 192.168.41.0 0.0.0.255 area 0
network 192.168.141.0 0.0.0.255 area 0
!
router bgp 1
no synchronization
neighbor 172.16.1.1 update-source Loopback0
neighbor 172.16.1.1 next-hop-self
no auto-summary
!
ip forward-protocol nd
!
no ip http server
!
!
ip explicit-path identifier 1 enable
!
!
!
!
!
nls resp-timeout 1
cpd cr-id 1
!
!
control-plane
!
!
!
voice-port 0/1/0
!
voice-port 0/1/1
!
voice-port 0/2/0
!
voice-port 0/2/1
!
!
!
!
!
!
!
gatekeeper
shutdown
!
!
line con 0
line aux 0
line vty 0 4
login
!
end

10R2#sh run

!
version 12.4
!
hostname 10R2
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
!
resource policy
!
ip subnet-zero
ip cef
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface Loopback0
ip address 10.1.3.3 255.255.255.255
!
ip address 10.1.21.2 255.255.255.0
duplex auto
speed auto
media-type rj45
negotiation auto
!
no ip address
shutdown
duplex auto
speed auto
media-type rj45
negotiation auto
!
interface Serial1/0
no ip address
shutdown
!
interface Serial1/1
no ip address
shutdown
!
interface Serial1/2
no ip address
shutdown
!
interface Serial1/3
no ip address
shutdown
!
no ip address
shutdown
duplex auto
speed auto
!
no ip address
shutdown
duplex auto
speed auto
!
router bgp 20
no synchronization

network 10.1.3.3 mask 255.255.255.255
no auto-summary
!
ip classless
!
!
ip http server
!
!
!
!
!
control-plane
!
!
!
!
!
!
!
!
!
!
line con 0
stopbits 1
line aux 0
stopbits 1
line vty 0 4
login
!
!
End
10R4#sh run

!
version 12.4
!
hostname 10R4
!
boot-start-marker
boot-end-marker
!
!
no aaa new-model
!
resource policy
!
ip subnet-zero
ip cef
!
!
!
!
!
no mpls ip
voice-card 0
no dspfarm
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
interface Loopback0
ip address 172.16.3.3 255.255.255.255
!
ip address 192.168.44.14 255.255.255.0
duplex auto
speed auto
media-type rj45
negotiation auto
mpls ip
!
no ip address
shutdown
duplex auto
speed auto
media-type rj45
negotiation auto
!
no ip address
shutdown
duplex auto
speed auto
!
ip address 192.168.41.4 255.255.255.0
duplex auto
speed auto
mpls ip
!
no ip address
shutdown
no fair-queue
!
no ip address
shutdown
clock rate 2000000
!
router ospf 1
network 172.16.3.3 0.0.0.0 area 0
network 192.168.41.0 0.0.0.255 area 0
network 192.168.44.0 0.0.0.255 area 0
!
ip classless
!
!
ip http server
!
!
!
!
!
control-plane
!
!
!
voice-port 0/1/0
!
voice-port 0/1/1
!
voice-port 0/2/0
!
voice-port 0/2/1
!
voice-port 0/3/0
!
voice-port 0/3/1
!
!
!
!
!
!
!
!
line con 0
stopbits 1
line aux 0
stopbits 1
line vty 0 4
login
!
!
End
9. How will you describe unequal cost load balancing from this lab?
Unequal cost load balancing in MPLS is done by using 16 hash buckets for next-hop which are
shared in rough rough propostion to configured tunnel bandwidth or load-share value.
10. Capture the output from the sniffer and comment on them?
Path message is contained in RSVP message. The explicit route followed is 192.168.14.4 192.168.141.1 - 172.16.4.4 to destination 172.16.1.1
ICMP echo request from 9R2 to 10R2
ICMP echo reply from 10R2 to 9R2

Group 2 and 3 - Lab 4

Uploaded by

Copyright:

Available Formats

Group 2 and 3 - Lab 4

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Group 2 and 3 - Lab 4

Uploaded by

Copyright:

Available Formats

Lab Assignment: 4

1. Enable debugging on each router and show the output:

2. Show ip route. Discuss the output?

3. Show ip route < loopback of YR4/XR4> on YR4/XR4. Discuss the output?

4. Show mpls traffic-eng tunnels. Discuss the output?

5. Show mpls traffic-eng tunnels brief. Discuss the output.

6. Ping from 10R2 to 9R2

Ping from 9R2 to 10R2

Target IP address: 10.1.3.3

10.1.12.1 0 msec 0 msec 0 msec

1 10.1.21.1 0 msec 0 msec 0 msec

Trace route for explicitly defined path:

1 10.1.21.1 0 msec 0 msec 0 msec

8. Submit running configuration of all the routers?

Current configuration : 1841 bytes

Running configuration on 10S1

Current configuration : 1907 bytes

vtp domain INWK

switchport mode access

Running Configuration on 9R1

Running Configuration on 9R4

Current configuration : 1857 bytes

Running configuration on 10R1

Current configuration : 2506 bytes

mpls traffic-eng tunnels

Running configuration on 10R2

Current configuration : 1447 bytes

bgp router-id 10.1.3.3

Current configuration : 1656 bytes

ICMP echo request from 9R2 to 10R2

ICMP echo reply from 10R2 to 9R2

You might also like