Heightworksiratatrainingmanualversion2 140911074418 Phpapp02 PDF

Rope
Access
Training
Manual
Acknowledgments
Some text in this document has been taken directly from the following documentation:
IRATA.org
IRATA International Code of Practice
IRATA International Training and Certification Scheme
Equipment user instructions (Petzl)
All Drawings by Heightworks with help from V Rigger
Copyright
All rights of the owner of the work are reserved. Unauthorised copying is prohibited where
there is a commercial or financial benefit
Candidate Name:
IRATA Number:
Course Dates:
Location:
IRATA Instructor(s):
I010 020914 Rev 2.0 IRATA Training Manual TACS Version
ABOUT THIS MANUAL
PLANNING AND MANAGEMENT
IRATA International system

Legal Framework
Legislation
Work at Height Regulations
Lifting Operations and Lifting equipment regulations (LOLER)
Personal Protective Equipment regulations (PPE)
The Provision and Use of work Equipment Regulations (PUWER)
The Reporting of Injuries Diseases and Dangerous Occurrences Regulations
The Control of Substances Hazardous to Health Regulations (COSCHH)
The Management of Health and Safety at Work Regulations
Risk assessment and Method Statement
Selection of access method
Selection of personnel & competence.
Exclusion zones & protection of third parties
Planning for emergencies and first aid
Suspension intolerance.
8
10
11
11
11
12
12
12
12
13
13
14
14
15
16
17
ROPE ACCESS EQUIPMENT.
21
Selection, PPE, EN Standards and CE Marking.

Equipment Traceability, Care and Maintenance , Storage, Lifespan.
Equipment Strength.
Inspection
Rope Access Equipment Setup
Helmets
Harnesses
Cowstails / Dynamic Rope
Ascenders
Descenders.
Back-up Devices
Maillons
Karabiners
Tape Slings
Wire Strops
Low Stretch Ropes
Etriers/ Footloops
Edge Protection
Pulleys
Locking Pulleys
Work Seat.
Fall Arrest Lanyards
Adjustable Work Positioning Lanyards
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
CONTENTS
CONTENTS
CONTENTS
KNOTS
45
Figure of 8
Figure of 9
Double Figure of 8
Alpine Butterfly
Barrel Knot
Stopper Knot
Flemish Bend
47
48
49
50
51
52
53
ANCHOR SYSTEMS
55
Anchor Systems
Hazard Avoidance
Rope Protection
Basic Anchor Systems
Angles of Rigging
Small Y-Hang
Wide Y-Hang
Re-anchors
Deviation
Angles Deviation
Retrievable Rigging
Work Restraint / Horizontal Lifelines
Vertical Fall Arrest Systems
Tensioned Ropes
Forces on Tensioned Ropes
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
RIGGING FOR RESCUE AND HAULING
71
Lowering
Releasable Attachments
Haulinglocking devices
2:1 Hauling System
3:1 Hauling System
Increasing Mechanical Advantage
Forces in Hauling Systems
Friction in Hauling Systems
Back-up Systems for Hauling and Lowering
Basic Hauling
Hanging Haul
Cross Haul
Complex Rescue System / Team Rescue
72
73
74
75
76
77
78
80
81
82
82
84
86
ROPE ACCESS MANOEUVRES
89
Back Up Devices
Descent
Ascent
Changeovers
Single Anchor Deviations
Double Anchor Deviations
90
90
90
90
91
92
Rope to Rope Transfers

Re- Anchors
Passing Mid-Rope Knots
Edge Obstructions
Use of Work Seats
Passing Mid-rope Protection
93
94
95
96
96
97
CLIMBING TECHNIQUES
99
Horizontal Aid Climbing

Vertical Aid Climbing
Climbing with Fall Arrest Lanyards
Fall Factors
Clearance Distance
Lead Climbing
100
101
102
103
105
107
Rope Rescues
109
Principles of Rescue
Descent Rescue
Ascent Rescue
Deviation Rescue
Rope to Rope Transfer Rescue
Re-Anchor Rescue
Large Re-Anchor Rescue
Mid-Transfer Rescue
Rescue Passing Mid Rope Knots
Tensioned Ropes for Rescue
110
111
112
113
114
115
116
117
118
119
121
Rescue from Aid Climb

Rescue from Fall Arrest Equipment
Short Link Rescue
122
123
124
Course Notes
125
CONTENTS
Climbing Rescues
ABOUT THIS MANUAL

This course manual is provided to supplement your IRATA Rope
Access Course. The manual is not a substitute for training and
should be used in conjunction with the following
documentation:
IRATA International Code of Practice
IRATA International Training, Assessment and Certification
Scheme
Equipment user instructions
ABOUT THIS MANUAL
Information for all candidates
Information for Level 2

and Level 3 candidates
Information for Level 3

candidates
PLANNING AND
MANAGEMENT
IRATA INTERNATIONAL SYSTEM

IRATA is the sole global trade association in the work-at-height sector; it has member
companies in every continent.
Industrial rope access has been developed by IRATA in the last 25 years to a point
where it is the chosen means of access for much of the work in the offshore oil and
gas industry as well as a range of projects in construction, civil engineering, the built
and natural environment and much more. Its success is based on thorough training
and strict work guidelines that deliver an unrivalled safe working record year after
year.
IRATA Internationals safe system of work comprises three main elements;
a) the code of practice (ICOP);
b) the training, assessment and certification scheme (TACS);
c) audited member companies, and their operating procedures.
International Code of Practice:
The code of practice gives recommendations and guidance on the use of IRATA International rope access methods, including training, to provide a safe system of work. It
is intended for use by IRATA International members, IRATA International rope access
technicians, national or regional enforcement agencies, safety officers and those who
commission rope access work, e.g. building contractors; multi-national oil and gas
companies; the renewable energy sector. This code of practice is applicable to the use
of IRATA International rope access methods for industrial purposes, i.e. for access to
buildings, other structures (on or offshore) or natural features, such as cliff faces,
where ropes are used as the primary means of access, egress or support and as the
primary means of protection against a fall.
Training and certification scheme:
This document details the requirements of IRATA Internationals training, assessment
and certification scheme (the scheme) and offers guidance to assist implementation.
It provides:
the levels of certification for new and existing IRATA International rope access
technicians, and explains the training syllabuses and assessment criteria required to attain and revalidate them;
guidance for candidates, including pre-training requirements and topics covered;
requirements and guidance for IRATA International trainer member companies;
requirements and guidance for IRATA International instructors;
requirements and guidance for IRATA International assessors, including the

marking process.
The scheme does not include operating procedures: these are drawn up for the specific task by operating companies following the IRATA International code of practice.
The ICOP also includes more information on the applicability of IRATA Internationals
rope access qualifications in the workplace.
Audited member companies and their operating procedures:

IRATA member companies are required to pass an IRATA audit every 3 years. This audit
is carried out by an independent auditor appointed by IRATA. The audited procedures
state how the IRATA member company will operate in accordance with IRATA Internationals requirements for quality assurance, safety, training and working practices.
Under the IRATA ICOP 2.6.1.2, only Level 3 rope access technicians are permitted to be
rope access safety supervisors. For more information concerning Supervision see IRATA
ICOP 2.6.
IRATA International qualifications and requirements are laid out in IRATA TACS Section
3,4,and 5. All technicians shall show awareness of the levels of technician competence,
and the requirements for revalidation and progression between levels.
Following the IRATA member companies procedures, IRATA ICOP and IRATA TACS will
help to ensure that work is carried out in a safe and professional manner and that the
member companies quality standards are met. Any documentation generated on-site
such as toolbox talks, equipment records, daily reports and accident reports etc are essential for site safety and the companies audit.
LEGAL FRAMEWORK
In the UK all work is governed by the Health And Safety At Work Act 1974, this act
places general duties on employers, clients, contractors, owners, employees and the
self-employed.
The Health and Safety Executive (HSE) is the body responsible for the encouragement, regulation and enforcement of workplace health, safety and welfare, and for
research into occupational risks in England and Wales and Scotland.
The HSE are also responsible for the production of the following documents:
Regulations
Regulations are law, approved by an act of parliament or European directive.
A breach of the regulations by either an individual or a corporation is a crime in the
UK which carries a fine of up to 20,000.
Approved codes of practice (ACOP)
Offer practical examples of good practice .
Have special legal status, if employers are prosecuted for a breach of health and
safety law, and it is proved that they have not followed the relevant provisions of the
ACOP, a court can find them at fault unless they can show that they have complied
with the law in some other way.
Guidance
The main purposes of guidance are:
Help people understand what the law says
To help people comply with the law
To give technical advice
Following guidance is not compulsory and employers are free to take other action.
But if they do follow guidance they will normally be doing enough to comply with
the law.
The IRATA ICOP is a voluntary code of practice and as such compliance is not a legal
requirement under UK law. However, it is mandatory for members of IRATA International to comply with the principles of the code of practice and this is a condition of
their membership.
10
LEGISLATION
WORK AT HEIGHT REGULATIONS 2005
In the regulations arrangements 2.(1). Work at Height is defined as:
Work in any place from where, if measures required by these regulations were not taken, a person could fall a distance liable to cause personal injury.
This means:
There is no minimum height requirement for work at height. Work at Height includes
all work activities where there is a need to control the risk of falling any distance liable
to cause personal injury, regardless of work task and duration. This includes getting to
and returning from the place of work.
Avoid -
working at height if at all possible
Prevent -
falls from height by utilising:Collective measure -Safe Work Platforms/Mobile Elevated Work Plat
forms/Scaffolds
Personal measure - Work Restraint/ Work Positioning/Work
Suspension
Minimise -
the consequences of falls by utilising:Collective measures - Airbags/ Safety Nets

Personal measures - Fall Arrest Equipment
Collective measures always take precedence over personal measures.

Planning work at height must also include planning for rescue/emergencies.
LIFTING OPERATIONS AND LIFTING EQUIPMENT REGULATIONS 1998
LOLER applies to rope access because the term load used in LOLER includes the lifting or lowering of a person.
3 main aims of LOLER:
Lifting operations are properly planned and managed.
Lifting equipment is used in a safe manner.
Lifting equipment is thoroughly inspected at suitable intervals by a competent
person.
Types of inspection under LOLER
- Pre-use
- 6 monthly
- Interim inspection
Hierarchy of measures
11
LEGISLATION
PERSONAL PROTECTIVE EQUIPMENT REGULATIONS 1992
Employers provide suitable and sufficient PPE
Employers provide training and information-sample of equipment instructions
PPE is inspected, maintained and stored correctly
Employees use, not interfere and report defects or deficiencies in its use
Category 1: Simple: (e.g. Gloves)
Category 2: Intermediate: (e.g. Boots, Helmets)
Category 3: Complex: e.g. Protection against mortal danger
Most rope access equipment is Cat 3 PPE. Cat 3 PPE must have CE mark and EN
Number.
PROVISION AND USE OF WORK EQUIPMENT REGULATIONS 1998
Any equipment which is used by an employee at work is covered under the regulations.
Employers must ensure that work equipment is:
Suitable for use and for the purpose and conditions in which it is to be used
Maintained in a safe condition for use
Inspected- to ensure that it is safe for use
Employers must also ensure that any risks created by the use of the equipment are
eliminated/ controlled by:
Hardware measures providing suitable guards, protection devices, stop buttons etc.
Software measures following safe systems of work, providing information and training etc.
REPORTING of INJURIES, DIESEASES and DANGEROUS OCCOURANCES
REGULATIONS 1995
The following must be reported:
A death or major injury
An over 7 day injury
A work related disease
A dangerous occurrence
CONTROL OF SUBTANCES HAZARDOUS TO HEALTH 2002
The COSHH regulations require employers to assess the risk to their employees, and
to prevent or adequately control those risks.
Part 15: Tells you what the dangers are.
Part 4- 8 : Tells you about emergencies, storage and handling.
8 steps to COSHH assessment:
Work out what hazardous substances are used in your work place and find out the
risks from using these substances to people's health.
12
Decide what precautions are needed before starting work with hazardous substances.
Prevent people being exposed to hazardous substances, but where this is not reasonably practicable, control the exposure.
Make sure control measures are used and maintained properly and that safety procedures are followed.
If required, monitor exposure of employees to hazardous substances.
If required, prepare plans and procedures to deal with accidents, incidents and
emergencies.
Make sure employees are properly informed, trained and supervised.
MANAGEMENT OF HEALTH AND SAFETY AT WORK REGULATIONS 1999
Any high risk job must have a risk assessment carried out by a competent person
(work at height is a high risk job) - A competent person is someone deemed by the
company to be suitably trained and experienced.
RISK ASSESMENT AND METHOD STATEMENT
Risk Assessment
A risk assessment is a careful, systematic examination of the hazards in the workplace that could cause harm to people or damage to equipment or property.
When undertaking a risk assessment it is important to balance hazard vs. risk.
A hazard is something that has the potential to cause harm/ damage to a person or
property.
A risk is the likelihood of that harm/damage actually occurring.
The HSE produce a simple guide to risk assessment:
5 steps to risk assessment1.
2.
3.
4.
5.
Identify the hazards

Decide who might be harmed and how
Evaluate the risks and decide on precautions
Record your findings and implement them
Review your assessment and update if necessary
For further information and sample risk assessments see IRATA ICOP Annex A and
part 2.2.4.
Carry out health surveillance where your assessment has shown that this is necessary or COSHH makes specific requirements.
13
Method statement
Method statement should set out working procedures to be followed for each stage
of the job and are an effective way of producing a safe system of work. All method
statements must include a rescue plan.
See IRATA ICOP annex N- recommended list of information to be held onsite.
Risk Assessments and Method Statements are essential for communicating safe
work practices and must be read and understood by all persons involved with the
work.
For further information on the contents of a method statement see IRATA ICOP
Annex B and 2.2.5.
Further Information
Further information about legislation applicable to the UK can be found in IRATA
ICOP Part 4.
SELECTION OF ACCESS METHOD
When deciding that rope access is a suitable access method for the work to be carried out, reference to the hierarchy of control measures taken from the Work At
Height Regs 2005 should be made.
For further information on assessing rope access as a suitable work method see
IRATA ICOP 2.2.3
SELECTION OF PERSONNEL AND COMPETENCE
IRATA ICOP 2.3 and 2.4 gives guidance on the selection of rope access technicians.
14
EXCLUSION ZONES AND PROTECTION OF THIRD PARTIES
Protect below
worksite
Protect anchor area
Exclusion zones may need to be set up above, below or

around rope access operations to protect people from exposed edges, dropped objects or protect the anchor system.
The site supervisor will Identify the exclusion area below the
worksite, set up any barriers or signage as required. Ensure
consideration is made for doorways access routes
(emergency exits)
Set up protection for the anchor area. Consider protection of

third parties from any hazard created by the worksite and any
risk of third parties either accidently or purposefully effecting
the rigged equipment.
Intermediate
protection
Any areas during the work where third parties may be effected
(balconies-, walkways, sub roofs etc) - will be controlled as
required.
Set up any debris netting where necessary .
Tools / equipment
controlled
All small tools and equipment will be attached to the harness

via a lanyard and /or a suitable tool bag / bucket will be
used to minimise the risk of dropped objects.
Large tools >8kg will be attached to a separate safety line .
Further information about exclusion zones can be found in IRATA ICOP 2.11.8
Third Party
Protection
15
PLANNING FOR EMERGENCIES AND FIRST AID

Arrangements for emergencies and first aid must be made during the planning stage
of any rope access operation. Full details of these arrangements must be included as
part of the risk assessment / method statement.
It is the responsibility of the IRATA Level 3 to take ownership of the rescue plan, communicate the emergency arrangements to the work team, implement any pre rigged
or rig for rescue system and ensure its effectiveness throughout the work task.
Elements of the rescue plan include:
Designated anchor points;

Required equipment;
Team size, competence, supervision and communication;
Step-by-step procedure for rescue;
First aid provision;
Contingency plan covering possible complications.
First aid equipment and the level of training required must be adequate and appropriate for the environment the work team is operating in.
If working in remote locations the need for a more comprehensive first aid kit and advanced training maybe required, it maybe advantages to make special arrangements
with the local emergency services and inform them of your location.
16
SUSPENSION INTOLERANCE
Also Called:
Suspension Trauma, Suspension Syncope,
Orthostatic Intolerance,
Harness-induced Pathology.
The following information is taken from IRATA
ICOP Annex G.
Suspension intolerance is a condition in which

a suspended person, e.g. In a harness, can
experience certain unpleasant symptoms,
which can lead to unconsciousness and eventually death. The reason for this is that the
body is not tolerant of being in an upright position and motionless at the same time. Persons
likely to be affected are those who are suspended in a generally upright position and who
are motionless, for example, when seriously
injured or unconscious, or when fastened vertically in a stretcher.
The condition been suspected in cases of

mountain climbers who fell and were suspended for up to several hours. Some of
these climbers died after rescue up to eleven days after their fall, for reasons that
have been postulated by medical professionals as being due to suspension intolerance. There have also been instances of cave explorers becoming stuck on their ropes
and who have died either while still on them or not long after being rescued. The reason for some of these deaths was again attributed to suspension intolerance. Some of
the symptoms have been experienced by rescuees feigning unconsciousness in rescue
training scenarios. The condition has been produced under experimental circumstances in persons who were suspended in a harness in a generally upright position and
who were motionless. In these clinical trials, where the test subjects were told not to
move, most experienced many of the effects of suspension intolerance, some including loss of consciousness, in just a few minutes. Others managed for longer before reporting symptoms. A similar situation might arise in a worker who falls into suspension
and is not moving, e.g. due to being exhausted, badly injured or unconscious.
WARNING! The advice given in this annex is

known best practice at the time of publication.
It is essential that persons responsible for rescue plans and rescues keep themselves fully
up to date with current practices.
17
Muscular action in moving the legs normally assists the return against gravity of
blood in the veins back to the heart. When the body is motionless, these muscle
pumps do not operate and if the person is in an upright position, an excess of blood
pools in the veins of the legs, which are capable of a large expansion and, therefore,
have considerable capacity. The excess of blood in the veins is known as venous
pooling. The retention of blood in the venous system reduces the circulating blood
volume and causes a disturbance of the circulatory system. This can lead to a critical reduction of blood supply to the brain and symptoms which include a feeling by
the person that they are about to faint, nausea, breathlessness, disrupted vision,
paleness, giddiness, localized pain, numbness, hot flushes, initially an increase in
pulse and blood pressure and then a decrease in blood pressure below normal. The
symptoms are known as pre-syncope and, if the condition is allowed to develop unchecked, can lead to unconsciousness (fainting) when it is known as syncope
and eventually death. It is possible that other organs critically dependent on a good
blood supply, such as the kidneys, could also suffer damage, with potentially serious
consequences. It seems that even the fittest person may not be immune to the effects of suspension intolerance.
Normal movement of the legs (e.g. When ascending, descending or working while
suspended) will activate the muscles, which should minimize the risk of excessive
venous pooling and the onset of pre-syncope. It is recommended that harness legloops are wide and well-padded, as this should help to spread the load and reduce
possible restrictions to blood-flow through the arteries and veins in the legs. The use
of a work seat should be considered if one position is expected to be sustained for
an extended period.
Although there is little evidence of the effects of suspension intolerance occurring in

the industrial rope access environment, an effective rescue plan is essential to ensure that, following an incident, a casualty can be removed quickly from the suspended position and cared for in a proper manner. The longer the casualty is suspended without moving, the greater the chances there are of the effects of suspension intolerance developing and the more serious it is likely to be.
18
A person suspended motionless in a harness awaiting rescue is likely to tolerate

suspension with the knees elevated. During rescue, elevation of the legs and
movement of them by the casualty or assisted by the rescuer, where safely possible,
may helpful. The casualty should be removed from suspension as soon as possible.
This is particularly important for a casualty who is motionless.
During and after rescue, standard first aid guidance should be followed, with an emphasis on airway, breathing and circulation management (ABC). Assessment of any
injuries should include those which may not be apparent, e.g. Damage to the neck,
back and vital organs.
In accordance with the advice given in a literature research and assessment carried
out by the UK Health and Safety Laboratory (HSL) in 2008 (HSE/RR708 Evidence
based review of the current guidance on first aid measures for suspension trauma),
the fully conscious casualty may be laid down and the semi-conscious or unconscious casualty placed in the recovery position (also known as the open airway position). This differs from earlier advice.
All casualties who have been suspended motionless in a harness should be taken to
hospital immediately for further professional medical care and observation. Medical
personnel should be advised that the casualty maybe suffering from the effects of
suspension intolerance.
Those preparing rescue plans should regularly review current best practice.
Rope access personnel should be able to recognise the symptoms of suspension pre
-syncope.
Motionless head-up suspension can lead to pre-syncope and sometimes syncope in
most normal subjects within 1 hour and to 20% of subjects within 10 minutes. Syncope can follow thereafter at an unpredictable time.
19
20
ROPE ACCESS EQUIPMENT
ROPE ACCESS
EQUIPMENT
21
Overview
This section aims to provide you with a thorough knowledge of the equipment
commonly used in rope access.
Selection
Rope access equipment should be chosen based on an assessment of:

Suitability of the equipment for the intended task and intended work environ
ment
Intended purpose as specified by the manufacturer
The likelihood and consequences of misuse of the equipment including
known incidents
Competence of the end user
Compatibility with existing equipment
Conformance with relevant standards
PPE
There are three categories of PPE according to its level of complexity and the level of
hazard against which it protects:
Category 1Simple (Protect against minor irritations or abrasions)
Category 2Intermediate (Helmets, Protective footwear)
Category 3Complex (Protect against mortal danger)
Most rope access suspension equipment and fall arrest equipment is Cat 3 PPE.
EN Standards and CE Marking

All PPE used in industrial rope access must meet the required standards for use in
the country they are to be used in. Within the European Union a CE mark on a product indicates that the item has been type tested and meets a minimum standard.
The EN number marked on an item indicates the relevant standard the item has
been tested against. Both the EN and CE marks are not intended to be an indication
of the quality of an item of equipment.
22
Equipment traceability
All equipment, when used in industrial rope access must be traceable to inspection
records and certificates of conformity. Normally this is achieved by unique ID numbers on the equipment, whatever method is used to identify equipment it is important we do not alter, damage or affect the performance of the equipment.
Care and Maintenance

Consult the manufacturers recommendations on how best to care for and maintain
your equipment.
Equipment should be stored in a secure area where access is restricted to necessary competent personnel only. Equipment should be stored in line with manufacturers recommendation, normally a cool , dry area away from direct sunlight. Care
should be taken to ensure that there are no potential causes of damage to stored
equipment, e.g., chemicals, sharp edges, heat etc.
Lifespan
All rope access equipment has a life span, consult the manufacturers recommendations for the item of equipment in question. In extreme cases the life of a piece of
equipment may be as short as its first use due to the environment that it is subjected to or any damage or degradation that may have occurred.
Storage
23
EQUIPMENT STRENGTH
BL: Breaking Load: The maximum load that can be applied to an item of equipment
before it breaks.
WLL: Working Load Limit: The maximum load, as determined by the manufacturer
that an item of equipment is designed to raise, lower or suspend.
SWL: Safe Working Load: The maximum load, as determined by a competent person
that an item of equipment is designed to raise, lower or suspend under particular
conditions.
It is normally recognised that the safe working load is 1 person or 2 people in an
emergency. For a more accurate calculation the below formula should be used.
Factor of Safety:
Metal Items: 5:1
SWL=B L
FOS
Textile Items: 10:1

E.g.
Low Stretch Rope
BL=3000kg
SWL=3000 = 300kg
10
Steel Karabiner
BL=2500kg
SWL=2500= 500kg
5
Textile items have a higher Factor of Safety as they are more susceptible to wear,
heat and chemical damage knotted ropes are also up to 50% weaker depending upon which knot is used.
Never exceed the SWL of the weakest item of equipment in the rope access system.
24
INSPECTION
There are 3 types of inspection to which all rope access equipment should be subjected to. These are the pre-use check, the thorough examination and in certain circumstances an interim inspection.
Pre-use Check- carried out by the user of the equipment and consists of a visual,
tactile and functional check. The results of a pre-use check are not normally recorded.
Thorough examination carried out by company appointed competent person before
equipment is used for the first time and then at 6 monthly intervals. The results of a
thorough examination should be recorded.
Further information regarding equipment inspection can be found in the manufacturers information that should be supplied with the item, and the IRATA ICOP:
Annex H- Equipment inspection checklists,
Annex I List of information to be recorded following a detailed inspection of rope
access equipment,
Annex J Resistance to chemicals and other properties of some of the man-made
fibres used in the manufacture of rope access equipment.
Interim inspection where equipment is used in arduous conditions or exceptional

circumstances are liable to jeopardize safety, interim inspections can be carried out
by a competent person in addition to the pre-use check and the thorough examination. Interim inspections should be recorded.
25
ROPE ACCESS EQUIPMENT SETUP
26
HELMETS
Helmets should be chosen that conform to a style more
appropriate to rope access applications than those of a
standard industrial helmet.
The helmet
should provide resistance to side impacts as well as from
above. It should have a fully adjustable cradle for comfort and a chinstrap to prevent
accidental loss. Helmets without a peak will prove beneficial when working in a vertical environment, in that vision will not be obscured whilst looking up.
What is it called?
Helmet.
Primary Function?
Protect the head.
Secondary Function?
May allow the attachment of additional PPE, lights, ear defenders, visors etc.
Correct Use
Do:
Ensure the helmet is traceable to relevant inspection records/certificates of conformity.
Ensure the helmet is inspected before each use.
Wear the helmet the correct way around.
Ensure the helmet is correctly fitted and adjusted to fit.
Check that paint and stickers will not alter the physical properties of your helmet over
time.
Protect your helmet from exposure to chemicals and solvents.
Don't:
Sit or stand on it.
Pack it to tightly.
Drop it.
Allow it to impact sharp or pointed objects.
Expose your helmet to high temperatures.
Conformity:
EN 397: Specification for industrial safety helmets.
EN 14052: High performance industrial helmets.
EN 12492: Mountaineering equipment Helmets for mountaineers Safety requirements and test methods.
Additional Information:
Manufacturers user instructions
IRATA ICOP section 2.7.12
HELMETS
Strength:
Not applicable
27
HARNESSES
Work positioning harnesses for rope access work
may be a sit harness or full body harness, depending on the nature of the work being carried out. If
the harness is to be used in a fall arrest situation a
full body harness must be used.
What is it called?
Petzl Navaho Full Body Harness.
Primary Function?
Support of rope access technician in work restraint, work positioning, work suspension or fall
arrest.
Secondary Function?
May allow the carrying of tools and equipment on gear loops.
May have a chest ascender built in to the harness.
Correct Use
Do:
Ensure the harness is traceable to relevant inspection records/certificates of conformity.
Ensure the harness is inspected before each use.
Ensure the harness is correctly fitted, adjusted to fit and correct size is selected.
Check that paint and other contaminants will not alter the physical properties of your
harness over time, such as buckle adjustment.
HARNESSES
Don't:
Allow it to contact sharp or pointed objects.
Expose your harness to high temperatures.
Overload gear loops.
Subject your harness to exposure to chemicals and solvents.
Conformity:
EN813: PPE against falls from height: Sit harness.
EN358: PPE against falls from height: Work positioning systems.
EN361: PPE against falls from height: Full body harness.
Strength:
Main D rings breaking load= 15kN minimum
Gear loop= 10kg maximum
IRATA ICOP Section 2.7.3
IRATA ICOP Annex D
IRATA ICOP Annex J
28
COWSTAILS/ DYNAMIC ROPE

Cowstails are tied into the central waist D-ring on the harness using dynamic rope.
Dynamic ropes cushion impacts and must be used during certain procedures to absorb the energy of possible falls. Cowstails should be able to withstand any forces
that might be imposed on them in times of emergency.
Cowstails that are not made from dynamic rope must not be subjected to a fall. This
equipment is for suspension only.
What is it called?
Cowstails, Device Lanyard, Anchor Lanyard.
Primary Function?
Connection from the harness to an attachment point.
Correct Use
Do:
Ensure the cowstails are traceable to relevant inspection records/certificates of conformity.
Ensure the cowstails are inspected before each use.
Ensure the knots in cowstails are correctly tied and tightened under body weight.
Protect your cowstails from exposure to chemicals and solvents.
Monitor Knots whilst in use.
Don't:
Expose your cowstails to high temperatures.
Conformity:
EN 892: Mountaineering equipment Dynamic mountaineering ropes Safety requirements and test methods.
Strength:
25kN
COWSTAILS
Secondary Function?
Dynamic rope must be used when belaying a lead climber.
Attachment of tools and work equipment.
29
ASCENDERS
Ascending devices are attached to the
working line and are used when the
rope access technician wishes to
climb up it. Typically, ascenders are used in pairs, a handled ascender and a chest
ascender. An ascender slides long the rope in one direction and jams in the other
direction. The cams teeth initiate a clamping action that pinches the rope between
the cam and the frame. The slot in the cam allows mud to be evacuated. Toothed
ascenders must never be used in a shock loading situation as damage or failure of
the rope may occur
What is it called?
Ascenders, Jammers, Hand Jammers, Chest Jammer, Croll, Ascension.
Primary Function?
Ascend a rope.
Secondary Function?
May be used in hauling systems, descending a rope.
ASCENDERS
Correct Use
Do:
Ensure the ascender is traceable to relevant inspection records/certificates of conformity.
Ensure the ascender is inspected before each use.
Ensure the ascender is compatible with the rope diameter.
Install the ascender on the rope the correct way around.
Don't:
Shock load or overload.
Use on wire rope.
Drop it.
Strength:
Rope damage will occur between 4-6Kn depending on rope diameter
Conformity:
EN567: Mountaineering equipment Rope clamps Safety requirements and test
methods.
EN12841-B: Personal fall protection equipment Rope access systems Rope adjustment devices.
30
DESCENDERS
Descending devices are used to attach the rope access
technician to the working line and to control the rate of descent
What is it called?
Descender, ID
Primary Function?
Make a controlled descent of a rope
Secondary Function?
May be used in hauling systems
Correct Use
Do:
Ensure the descender is traceable to relevant inspection records/certificates of conformity
Ensure the descender is inspected before each use
Ensure the descender is compatible with the rope diameter
Ensure the descender is correctly installed on to the rope
Protect your descender from exposure to chemicals and solvents
Strength:
150kg in normal use
250kg in a rescue
Slips at around 600kg
Conformity:
EN341-A: PPE against falls from height: Descender devices
EN12841-C: Personal fall protection equipment Rope access systems Rope adjustment devices.
DESCENDERS
Don't:
Shock load or overload
Drop it
Let go of the tail end of the rope whilst the descender is not locked off.
31
BACK UP DEVICE
Back-up devices are attached to a rope access
technicians safety line. In the event of a failure of
the working line or loss of control by the rope access technician, back-up devices are intended to
lock on to the safety line without causing catastrophic damage to the safety line.
What is it called?
Back-Up Device.
Primary Function?
Arrest a fall following an uncontrolled descent or failure of the working line.
Secondary Function?
Back up device in a lowering system.
BACK UP DEVICES
Correct Use
Do:
Ensure the back-up device is traceable to relevant inspection records/certificates of
conformity.
Ensure the back-up device is inspected before each use.
Use the correct energy absorber (ASAP).
Use a dynamic rope cowstail maximum length of 60cm (Shunt).
Ensure the rope diameter is compatible with the device.
Ensure the back-up device is installed on the rope correctly.
Maintain a high attachment.
Don't:
Allow loops of slack rope to gather between the device and the anchor point.
Operate a descender and shunt simultaneously.
Strength:
1 person
2 people in a rescue using an L57 Absorbica (ASAP)
Slips down the rope at 2.5-3 kN (Shunt)
Conformity:
EN353-2: PPE against falls from height: Guided type fall
arrestors. Part 2. Specification for guided type fall arrestors on a flexible anchorage line.
EN12841-A: Personal fall protection equipment Rope
access systems Rope adjustment devices.
32
MAILLON
ed
be
Screw link connectors are more

appropriate than other types of
connector for infrequently operatconnections or where there might
a risk of cross loading across the
gate.
What is it called?
Maillon , Screw Link
Primary Function?
Attaching equipment to the ventral harness attachment point.
To make a semi-permanent connection, or where there is a risk of cross loading a
karabiner.
Secondary Function?
Attaching rope to anchor points.
Correct Use
Do:
Ensure the maillon is traceable to relevant inspection records/certificates of conformity.
Ensure the maillon is inspected before each use.
Ensure that maillon is compatible with other equipment used in the rope access system.
Strength:
Semi-circular 10mm: 45 Kn Breaking Load
Delta 8mm: 27.5Kn Breaking Load
Delta10mm : 45 Kn Breaking Load
Conformity:
EN 362: PPE against falls from height: Connectors.
EN 12275: Mountaineering equipment Connectors Safety requirements and test
methods.
MAILLONS
Don't:
Over tighten the screw closure.
Exceed loads recommended by the manufacturer.
Drop it.
Store with the gate open.
33
KARABINERS
All karabiners, when used in rope access must have a locking
mechanism, either screw gate or self locking.
Both aluminium and steel karabiners are used in rope access, aluminium karabiners
What is it called?
Karabiner, Carabiner, Krab, Connector.
Primary Function?
To temporarily connect elements of a rope access system together.
Secondary Function?
Connecting tools, equipment and bags.
Correct Use
Do:
Ensure the karabiner is traceable to relevant inspection records/certificates of conformity.
Ensure the karabiner inspected before each use.
Ensure any load placed on the karabiner is along the major axis.
Ensure that the gate is closed and locked.
Don't:
Place any load across the gate.
Load over an edge.
Allow 3 way loading.
Drop it.
KARABINERS
Strength:
22Kn minimum breaking load across the major axis.
Conformity:
EN 362: PPE against falls from height: Connectors.
IRATA ICOP Annex F.3.7
34
TAPE SLINGS
Tape slings are used to create an anchor point when placed around a structure. They are normally made from textile webbing and may have a protective
sleeve to reduce damage to the sling.
What is it called?
Tape sling, Sling, Anchor Sling.
Primary Function?
Used as a temporary/ moveable anchor point.
Secondary Function?
Releasable attachments.
Lanyard for tools.
Correct Use
Do:
Ensure slings are traceable to relevant inspection records/certificates of conformity.
Ensure the sling is inspected before each use.
Protect from sharp edges/objects.
Protect your slings from exposure to chemicals and solvents.
Don't:
Allow it to contact sharp or pointed objects
Expose your sling to high temperatures
Strength:
22- 30Kn Breaking Load
IRATA ICOP Annex J
SLINGS
Conformity:
EN 566: Mountaineering equipment Slings Safety requirements and test methods.
EN 795: Protection against falls from height Anchor devices Requirements and
testing.
35
WIRE STROPS
Wire stops are used to create an
anchor point around a structure.
Wire stops are often encased
within a protective sleeve to protect the structure and strop from
damage. Wire strops are less susceptible to damage from heat, chemicals and cuts.
What is it called?
Wire strop, strop, anchor slings.
Primary Function?
Used as a temporary/ moveable anchor point.
Secondary Function?
Can be used as an attachment to a rope or anchor point whilst carrying out hazardous work.
Correct Use
Do:
Ensure the strop is traceable to relevant inspection records/certificates of conformity.
Ensure the strop is inspected before each use.
Don't:
Drop it.
WIRE STROPS
Strength:
30 kN Breaking Load.
Conformity:
EN 795: Protection against falls from height Anchor devices Requirements and
testing.
36
LOW STRETCH ROPE

Low stretch rope is used to create an anchor line system.
What is it called?
Low stretch rope, semi-static rope, anchor lines
Primary Function?
Rope access anchor lines, working and safety.
Secondary Function?
Hauling equipment and tools
Do:
Ensure the rope is traceable to relevant inspection records/certificates of conformity
Ensure the rope is inspected before each use
Protect from sharp edges/ objects
Protect your rope from exposure to chemicals and solvents
Store in suitable places.
Don't:
Sit or stand on it
Drop it
Allow it to contact sharp or pointed objects
Expose friction and high temperatures.
Strength:
27kN Breaking Load
Conformity:
EN 1891: PPE against falls from height: Low stretch kernmantle rope
IRATA ICOP Annex J
LOW STRETCH ROPE
Correct Use
37
ETRIERS/ FOOTLOOPS
Footloops are used in addition with a hand
ascender when climbing a rope. Etriers are
used as a multi step footloop generally for
aid climbing or when maintaining a comfortable work position whilst suspended.
What is it called?
Etrier, Footloops.
Primary Function?
Allow for convenient climbing up a rope or
along a structure.
Secondary Function?
Use for a counterbalance technique during a rescue.
Correct Use
FOOTLOOPS/ ETRIER
Do:
Ensure the footloop is inspected before each use
Protect your footloop from exposure to chemicals and solvents
Use the correct length for your body height or the task.
Don't:
Use as a load bearing item of equipment
Conformity:
None
38
EDGE PROTECTION
The best form of rope protection is to rig ropes to avoid edges and hazardous objects, where this is not reasonable practicable suitable rope protection equipment
must be used. Ropes must be protected from contact with sharp or abrasive surfaces or hot surfaces, failure to do this may lead to the ropes failing with catastrophic
results. Rope protection may take many forms such heavy duty wool carpet, simple
canvas padding or edge rollers.
What is it called?
Rope protector, edge rollers, edge pad.
Primary Function?
Protect the ropes form sharp edges, abrasion or hot surfaces.
Correct Use
Do:
Ensure the protector is inspected before each use
Ensure the protector is correctly installed and in the correct place
Ensure the rope protector is fixed into position
Don't:
Assume your rope protection is adequate.
Use PVC rope protectors due to potential melting of the PVC caused by friction.
Conformance:
None
IRATA ICOP Section 2.11.3.5 to 2.11.3.8
IRATA Safety Bulletin 22
EDGE PROTECTION
Secondary Function?
None
39
PULLEYS
Pulleys are used to reduce the friction of
any rope running through it for example
when building hauling systems, or when
changing the direction of moving ropes.
Pulleys may be fixed cheek or swing
cheek, other styles of specialist pulley are
available but these are the most common
types. As a rough guide the larger the pulley wheel is then the more efficient it is.
Pulleys which include ball bearings will
reduce friction further.
What is it called?
Pulley, Block.
Primary Function?
Reduce friction of a moving rope.
Secondary Function?
Used in hauling systems to reduce friction.
To change the direction/deviate moving ropes.
Correct Use
Do:
Ensure the pulley is inspected before each use.
Ensure the pulley is compatible with other components in the system.
PULLEYS
Don't:
Drop it
Overload it
Use a swing cheek pulley with one cheek open.
Strength:
15-40 kN
Conformity:
EN 12278: Mountaineering equipment Pulleys Safety requirements and test
methods
40
LOCKING PULLEYS
Locking pulleys are used as
a progress capture device in
hauling systems, they are
especially useful for long or
heavy hauls as they minimise friction in the system.
What is it called?
Pro Traxion, Micro Traxion, Locking Pulley.
Primary Function?
Progress capture device for hauling systems.
Correct Use
Do:
Ensure the pulley is inspected before each use.
Ensure the pulley is compatible with other components in the system.
Ensure that the device is installed on to the rope in the correct direction.
Don't:
Subject the device to possible shock loads
Drop it
Overload it
Use a swing cheek pulley with one cheek open.
Strength:
Rope Clamp:WLL 2.5kN
WLL: 5-6 kN
Conformity:
EN 12278: Mountaineering equipment Pulleys Safety requirements and test methods
EN567: Mountaineering equipment Rope clamps Safety requirements and test methods.
LOCKING PULLEYS
Secondary Function?
As a Pulley
AS an emergency ascender
41
WORK SEAT
A work seat is used to provide comfort to
a rope access technician when suspended for long periods of time, a work seat
is not part of the fall prevention system
What is it called?
Work seat, comfort seat.
Primary Function?
Increase the comfort and support of a rope access technician.
Secondary Function?
None.
Correct Use
Do:
Ensure the work seat is inspected before each use
Protect your work seat from exposure to chemicals and solvents
Ensure the harness remains the primary means of support
Don't:
Use the work seat as the primary means of support
WORKSEAT
42
FALL ARREST LANYARDS

Double fall arrest lanyards are used to allow users to remain
constantly attached whilst moving on a structure. Single fall arrest lanyards can only protect a worker involved in work in a
fixed position. It is important that two single lanyards are not
used to create a double lanyard as this can potentially double
the impact force generated by a fall.
Length and style of lanyards should be suitable for the task.
The overall length of the lanyard will be determined by the energy absorber used, this must not exceed 2m including all connectors.
What is it called?
Fall Arrest Lanyards, energy absorbing lanyards.
Primary Function?
Arrest a fall.
Correct Use
Do:
Ensure the fall arrest lanyard is traceable to relevant inspection records/certificates
of conformity.
Ensure the fall arrest lanyard is inspected before each use.
Use fall arrest lanyards with a full body fall arrest harness.
Protect your fall arrest lanyards from exposure to chemicals and solvents.
Ensure there is sufficient clearance distance required should the energy absorber be
deployed.
Ensure that connectors are compatible with the structure.
Don't:
Drop it.
Expose your fall arrest lanyards to high temperatures.
Continue to use or reuse after a significant fall has been arrested.
Conformity:
EN 355: PPE against falls from height: Energy absorbers.
EN 354: PPE against falls from height: Lanyards
IRATA ICOP Annex E
FALL ARREST LANYARDS
Secondary Function?
Use as a work restraint lanyard.
43
ADJUSTABLE WORK POSITIONING LANYARD

Work positioning lanyards are often used to
support a rope access technician, either partially or fully.
What is it called?
Work positioning lanyard, Grillon, work restraint lanyard.
Primary Function?
To support a rope access technician on a
structure.
Secondary Function?
May be used as a restraint lanyard.
Releasable attachment.
Anchor point.
Correct Use
Do:
Ensure the work positioning lanyard is traceable to relevant inspection records/
certificates of
conformity
Ensure the work positioning lanyard is inspected before each use
Protect your work positioning lanyard from exposure to chemicals and solvents
Don't:
Fall onto a work positioning lanyard
Allow it to contact sharp or abrasive edges.
GRILLON
Conformity:
EN 358: PPE against falls from height: Work positioning systems.
IRATA ICOP 2.7.1.5.2
IRATA ICOP Annex E.3
44
KNOTS
KNOTS
45
Tying knots and rigging ropes are a fundamental part of rope access, this section
aims to give guidance of what knots are acceptable in rope access, there uses, common methods of rigging ropes and the principles of safe rigging.
Additional information can be found in the IRATA ICOP Section 2.7.9, 2.112.11.9.3.2 and IRATA ICOP Annex F.
The anchor system used for rope access should be unquestionable reliable.
It is beyond the scope of this manual to provide information on installation and testing of various anchor systems, all anchors used in rope access should meet the requirements of local legislation, guidance and manufacturers recommendations.
Knots form an important part of rope access. They are used to attach ropes to anchors during rigging and for attaching rope access personnel. As such the ability to
tie knots and have a fundamental knowledge of various knots and their uses is essential.
The key to tying knots correctly is that they must be neat and dressed properly as
this will impact directly on their strength, energy absorbency and the ease with
which they can be untied. This is also an obvious gauge of the level of care and
competency of the rope access technician.
See IRATA ICOP 2.11.5
The following knots will be addressed in this section:
Figure of 8 on the bight
Figure of 9 on the bight
Double figure of 8 on the bight (Bunny Knot)
Alpine butterfly
Barrel knot
Stopper knot
Once a knot has been tied, dressed and tightened properly it should have a tail of
not less than 10cm (4 inches) (IRATA ICOP 2.11.5.4), when using a stopper knot in
the ends of ropes the tail should be at least 30cm (12 inches) (IRATA ICOP
2.11.3.9).
KNOTS
If a tail end is too long then an additional stopper knot must be added to prevent
descending off this tail if unintentionally used.
46
FIGURE OF EIGHT
Overview
The fig.8 is the most commonly used knot for rigging ropes,
the knot forms a strong and secure loop in the end of the
rope.
What is it called?
Figure of 8 on the bight, Figure of eight.
Primary function
To form a loop in the end of a rope.
Secondary function
A variation of a figure of eight can be used to tie two ropes
together.
Can be rethreaded around attachment or anchor point.
Correct use
Dos
Ensure the knot is loaded end to end.
Keep the loop as small as possible.
Ensure the length of the tail is 10cm minimum.
Strength
23-34% Loss
FIGURE OF EIGHT
Don'ts
Allow the loop to be cross loaded.
47
FIGURE OF 9
Overview
The figure of 9 is used in place of a figure of 8 however it is
slightly stronger and easier to untie after heavy or prolonged
loading.
What is it called?
Figure of 9 on the bight, figure of 9.
Primary function
To form a loop in the end of a rope and attached to anchor
points.
Secondary function
None.
Correct use
Dos
Don'ts
FIGURE OF 9
Strength
15-30% Loss
48
DOUBLE FIGURE OF 8
Overview
The Double Figure of Eight is another variant of the Figure of Eight
knot and whilst basically the same, once tied it will give two loops
that can be used as attachments. This is normally applied where
the load on the rope needs to be shared between two anchors in
close proximity to each other.
The advantage of the Double Figure of Eight is that should one
loop fail it will not cause the other to lose strength or slip. The disadvantage of this knot however is the amount of rope used to tie
it.
What is it called?
Double figure of 8 on the bight, bunny Knot, bunny Ears.
Primary function
To attach each anchor line to 2 different anchor points.
Secondary function
May be used to attach to a casualty so they may be hauled in an
upright position when connecting to both ventral and sternal harness attachment points.
Correct use
Don'ts
Rig both ropes with one knot.
Attach both loops to the same anchor point.
Strength
23-39% Loss
DOUBLE FIG 8
Dos
Ensure the knot is loaded correctly.
Keep the common loop towards the centre of the knot.
49
ALPINE BUTTERFLY
Overview
The alpine butterfly is a mid rope knot suitable for multidirectional loading, because of this it is used to form y-hangs, isolate damaged sections of rope and make points of attachment
along a rope.
What is it called?
Alpine butterfly, Alpine, Butterfly.
ALPINE BUTTERFLY
Primary function
Used in conjunction with a figure of 8 on the bight to form a Yhang.
Secondary function
To isolate damaged rope.
To make a point of attachment mid way along a rope.
Correct use
Dos
Ensure that when tightening the knot it is pulled along the length
of the rope.
Don'ts
Allow the knot to capsize and become mis-loaded.
Strength
28-39% Loss
50
BARREL KNOT
Overview
A barrel knot is used in the end of the cowstails as it
grips the karabiner tightly and prevents it from being
cross loaded. In testing the barrel knot has shown to
have greater shock absorbing qualities than other
knots used on the ends of cowstails. Great care must
be taken when using a barrel knot to ensure it has
been tied the correct way so when the cowstail is
weighted, the knot tightens around the karabiner and
does not pull through.
What is it called?
Barrel knot, Scaffold knot.
Primary function
Used to terminate cowstails.
Secondary function
Used where a rigging must be kept as compact as possible
Correct use
Dos
Ensure the knot tightens around the karabiner when
loaded.
Ensure the tail end is 10cm (4 inches) long.
Strength
23-33% Loss
BARREL KNOT
Don'ts
Overload as the knot becomes very difficult to untie.
51
STOPPER KNOT
Overview
A stopper knot is used to prevent rope access technicians abseiling off the end of the rope. A stopper knot
will be in the end of every rope that is rigged. See IRATA ICOP 2.11.3.9
What is it called?
Stopper knot
Primary function
To prevent descending off the end of the rope.
Secondary function
None.
Correct use
Dos
Ensure a stopper knot is present in the end of each
rope that is rigged.
Ensure the tail below the knot is a least 30cm
(12inches).
Don'ts
Use a knot that may roll off the end of the rope.
STOPPER KNOT
Strength
N/A
52
FLEMISH BEND
Overview
A Femish bend is used to join two
ropes together
What is it called?
Flemish Bend or Figure 8 variation
Primary function
To join two ropes together
Secondary function
None.
Correct use
Dos
Ensure the length of the tail is 10cm
minimum.
Don'ts
FLEMISH BEND
Strength
23-34% Loss
53
54
ANCHOR SYSTEMS
ANCHOR SYSTEMS
55
ANCHOR SYSTEMS
All persons engaged in industrial rope access techniques must have two independent points of attachment, this may be achieved by using two strops around a beam
whilst aid climbing or with the use of an anchor system whilst abseiling. These
should be arranged so that in the event of one point of attachment failing the technician remains protected by the other point of attachment and cannot suffer a fall.
Typical arrangements of anchor system include:
Basic Anchor System
Small Y-Hang
Wide Y Hang
Re-anchor
Deviation
Pull Through
Work restraint/ horizontal lifelines
Vertical fall arrest lines
Tensioned ropes
Releasable anchors
ANCHOR SYSTEMS
The ability to build a basic anchor system and a small Y-hang are skills required at
all levels. Levels 2 and 3 are required to have a knowledge of more advanced rigging
systems.
What ever type of system is rigged consideration must be given to avoiding sharp,
hot or abrasive surfaces. Where these can not be avoided adequate rope protection
must be installed. This rope protection must be resilient enough to comfortably control the hazard.
For additional information on installing and placing anchors see IRATA ICOP Annex F.
56
HAZARD AVOIDANCE
Rig Ropes
Ensure method
statement is
adhered to
Select anchors
Attach ropes to
anchors
Identify and install

edge protection
system where
necessary
mid rope abrasion
elimination or
protection
protection from any
hazardous tools or
work

rope protection
below work area
The supervisor should ensure that the RAMS are adhered to at

all times during the rope access operation. If there is any need
to deviate from this company management should be contacted, the RAMS should be amended and agreed with the client
before any work commences.
Anchor points should be selected by the Supervisor in accordance with the RAMS. IRATA ICOP annex F, 2.7.9 and 2.11.2 can
be used for onsite . In all cases they should be unquestionably
reliable for both normal and rescue loads and a minimum of
two separate anchors per person should be used.
Consideration should be made to any abrasion points on the
anchor points and suitable attachment slings, strops or connectors will be used.
Where possible ropes should be rigged to avoid any edges,
where this is not possible suitable edge protection should be
installed as per RAMS a radius of greater than 5mm will be
achieved
Any abrasion points or other obstructions that may affect the
integrity of the rope should, where practicable be avoided by
the use of re-belays or deviations. If this is not practical suitable
rope protectors should be used. where the rope protectors are
used to protect the rope 1 protector should be fastened to each
rope
The rope immediately above the technicians descender and
backup device should be protected if the task involves the use
of tools or equipment that may affect it (cutting, welding etc).
The RAMS should outline the specific method of protection to
be used.
The rope below the technician should be protected from falling
debris and being walked on. Good housekeeping, and coiled or
bagged ropes may be used.
HAZARD AVOIDANCE
Inspect equipment
All team equipment should be inspected every time it is used,

this should be done by the technician carrying out the rigging
under the supervision of the IRATA l3 supervisor
57
ROPE PROTECTION
The correct use of rope protection is a critical element when rigging ropes, in the
first instance the need for rope protection must be avoided by the use of other rigging systems such as re-belays and deviations.
Where the use of rope protection is unavoidable then consider the use of edge pads
and rope protectors. An assessment must be made as to the severity of the abrasion point and therefore the type of rope protector selected.
ROPE PROTECTION
Edge pads are often fixed to the structure and allow a wide area to be protected and
allow for some side-ways movement of rope access technicians.
Rope protectors provide a limited amount of protection to ropes when rigged over an
edge. When using a rope protector ropes must not be allowed to move from side to
side across the edge as this may cause catastrophic failure of both rope protector
and ropes. See IRATA Safety Bulletin 22.
When using rope protectors it is important that they are fixed into position and can
not become dislodged. When securing rope protectors they should be attached to
the back-up rope by a knot that will not slide down the rope.
Candidates: Shall show awareness of the potential consequences of such hazards affecting
equipment and of methods for removing, avoiding, containing or reducing them. All candidates
shall show awareness of how their movement on the ropes may increase the risk from such hazards.
All candidates shall demonstrate attaching wrap-around style rope protectors.
Level 2 and Level 3 candidates shall be capable of identifying common hazards and shall demonstrate selecting and implementing appropriate methods of rigging or protection.
Trainers: shall emphasize the application of the hierarchical approach (as is detailed in ICOP Part 2,
2.7 and 2.11, and Annex P), which prioritizes the removal of hazards before considering avoidance
through rigging methods or mitigation through rope protection. The level of protection offered by various rope protection methods should be explained. Consideration should be given to arranging separate protection for each rope.
Assessors: Should look for the appropriate choice of method and that adequate protection is
achieved.
58
BASIC ANCHOR SYSTEM

A basic anchor system uses anchors that are close
together, with the least amount of components to
keep the system as simple as possible. When using
the above
systems the load is shared equally between the two
anchor points.
Candidates: All candidates shall demonstrate the rigging of a basic anchor system.
Level 2 and 3 candidates shall be expected to demonstrate rigging at height
Trainers: shall include the basic principles of rigging and attachments in rope access work, e.g. each rope should have its own separate anchor. Both rope systems
may be connected to each other for added security. Emphasis should be placed on
checking that the ropes are correctly rigged so that, if one should fail, a shock load
would not be passed on through the system. Knots should be dressed and set. Emphasis should also be placed on the use of different types of slings and rigging
equipment, appropriate to the structure.
Assessors: may observe demonstrations at ground level for level 1. A variety of
knots and methods are acceptable.
BASIC ANCHOR SYSTEM
A basic anchor system may use two figure of 8

knots, two karabiners and two strops these may
both be clipped together to achieve load sharing.
59
ANGLES OF RIGGING
ANGLES OF RIGGING
All rope access technicians' should have an understanding of the angles of rigging
and how the internal angle of a Y-hang affects the forces transferred to the anchor
points.
The preferred angle of rigging a Y-hang is 90 or less.
The maximum angle of normal rigging is 120. At this angle all the forces in the
system are equal.
Above 120 and there is more force on the anchor points than there is suspended
on the rope. Accurate calculations are required when rigging using large angles.
60
SMALL Y-HANG
A Y-hang is used where a load is to be shared between two different anchor points or the ropes
need to be in a certain position.
A small Y-hang is used when the anchors are too
far apart for a basic anchor system.
A Y-hang is constructed using a fig. 8 or fig. 9 knot
in the end of the rope, and connected to one anchor.
An alpine butterfly is tied further down the rope,
this can then be attached to the second anchor
point.
The alpine butterfly can then be adjusted to ensure equal loading on both anchor points, or to position the rope in a required position.
SMALL Y-HANG
Alternatively a double figure of eight on the bight

can be used to achieve a small Y hang.
61
WIDE Y HANG
Where a Y-Hang is rigged with anchor 1.5m or more apart then this would be
considered a wide Y-hang.
A wide Y-hang is rigged with a double anchor system, two strops and two karabiners
are required on each side of the Y-hang.
WIDE Y-HANG
The use of a double anchor system is to protect from an out-of-control swing caused
by a single item of failure.
Candidates: All candidates shall demonstrate the rigging of a small Y-hang between
anchors less than one metre apart. Level 2 and 3 candidates shall demonstrate the
rigging of a Y-hang between wider anchor points, where the consequence of failure
of any one item needs consideration. Level 2 and 3 candidates shall be expected to
demonstrate rigging at height. Training shall expand on the instruction for the basic
anchor system, and explain the need to avoid large angles wherever possible. Anchors shall be equally loaded and positional adjustment demonstrated.
Trainers: shall emphasise the consequences of failure of any one item of equipment,
and the need for double anchor systems where a swing could cause injury to personnel, or damage to equipment or property. Inclusion of extra rigging rope may be appropriate in some circumstances.
Assessors: may observe demonstrations at ground level for Level 1. A variety of
62
RE-ANCHORS
Ropes are re-anchored to either avoid a hazard or to position a rope access technician closer to the work area.
A re-anchor may also be used to reduce the length of a
single drop into multiple smaller drops to help limit the
amount of stretch in the rope over long distances.
When rigging a re-anchor, consideration should be given
to the size of the loops, if the loops are too small or too
tight then passing through the re-anchor will be difficult.
For level 2 and 3 candidates consideration must be given to rescue past a re-anchor, again, the larger the
loops the easier it is to pass yourself and a casualty
through the re-anchor.
The right hand picture shows a
re-anchor rigged using two figure of 8 knots, two karabiners
and two strops, a re-anchor
may also be rigged using a Yhang if the anchors are offset
or a distance apart.
Candidates: Level 2 and 3 candidates shall demonstrate the correct rigging of a re-anchor at height.
For Level 2 candidates the offset shall be less than 1.5 metres, whilst for Level 3 candidates the offset may be any distance apart.
Trainers: shall emphasise the consequences of failure of any one item of equipment. Rigging should
consider ease of use, and take account of options and methods for rescue; generally shallow re-belay
loops make both access and rescue more difficult, particularly where the offset is large.
Assessors: should note that a variety of knots and methods are acceptable.
RE-ANCHORS
A re-anchor under 1.5m is considered small. A re-anchor over

1.5m should be considered as
wide.
63
DEVIATION
Single Anchor
Deviation
Double Anchor
Deviation
Deviations are a method of rigging which allows re-direction of the path of the
ropes. Ropes may be deviated to provide more accurate positioning for the rope
access technician or to avoid hazards. Unlike re-anchors, deviations allow positioning with a system rigged for rescue. On a continuously overhanging structure, or to
constrain movement, a series of deviations may be used. Deviations can be divided into two types:
DEVIATION
Single-anchor deviations are used to deviate the ropes (or the working line alone)
by a small angle only. Single-anchor deviations are only appropriate where their
failure would not result in serious consequences (such as a large swing into a
structure, or contact with a sharp edge) and are normally rigged as a single anchor
system.
Double-anchor deviations may deviate the ropes by a greater angle and distance
than a single-anchor deviation, and allow the ropes and user to be protected
against more serious hazards such as a sharp edge or a large swing into a structure. Such a deviation utilizes a double anchor system, with suitably rated anchors
and connection components, to provide protection against failure of any one item.
Where a large angle is created, users should consider whether a re-anchor may be
more appropriate.
Candidates: Level 2 and 3 candidates shall demonstrate the correct rigging of either type of deviation
with due regard to the angle and distance required to achieve the repositioning, and the ease of use/
passing in both ascent and descent. At Level 2 the type of deviation required shall be specified; at
Level 3 candidates shall choose the appropriate type for a given situation.
Trainers: shall explain which type of deviation is appropriate for which situation, and where other
types of rigging (such as re-anchors) may be more appropriate. Anchor loading, and required anchor
strength in relation to the angle of deflection of the rope should be explained.
64
ANGLES OF DEVIATION
ANGLES OF DEVIATION
65
RETRIEVABLE RIGGING
RETRIEVABLE RIGGING
The use of a pull-through allows the ropes to be retrieved once work has been completed. A pull through is often used at the end of an aid climb job as an easy way to
exit the work area and to save climbing back to the start.
When rigging a pull through it is important to consider suitable rope protection, but
this should be rigged in a way that still allows the ropes to be pulled down.
It is vital that users of a pull through get on the correct side of it. Whilst transferring
onto a pull through it is advisable to keep a separate point of attachment on to the
structure.
Avoid cross loading or loading karabiners over an edge, if this is unavoidable
Maillons may be more suitable.
Pull-through should be considered temporary rigging for access or egress, and therefore are not considered appropriate for rescues.
Candidates: Level 2 and 3 candidates shall demonstrate the correct rigging of a pullthrough from both the ground and from the anchor points.
Trainers: shall emphasise the need to protect the ropes against unseen abrasion.
Good rope management shall be explained to ensure two independent systems are
maintained, and to avoid cross loading of karabiners.
Assessors: should note that candidates need only demonstrate one pull-through at
assessment, at the assessors discretion. A variety of methods is acceptable.
66
Work restraint systems should, if rigged properly, prevent rope access technicians
from being in a position where a fall could take place.
Where a restraint system is used, the use of a single rope may be acceptable.
If horizontal lifelines are to be used to fully suspend a rope access technician then a
double rope system should be rigged.
When a restraint system is rigged over a long distance it may be necessary to use
intermediate anchors for support and to limit the amount of deflection so a fall prevention remains.
Work restraint systems should be rigged as high as possible, but still within reach of
workers.
Additional work restraint systems can be attached to the horizontal lifeline or attached directly to anchor points to allow a rope access technician to belay themselves or another technician towards an unprotected edge.
Candidates: Level 2 and 3 candidates shall demonstrate appropriate rigging of work
restraint lines. Candidates shall ensure that the restraint method does indeed prevent them from entering a fall hazard zone and shall demonstrate knowledge of
work restraint equipment, including where and when it is appropriate to use it within
rope access.
Trainers: shall emphasise that this access method restrains users within a safe area
where they remain supported by the structure. Trainers should explain that work restraint lines can be rigged in a variety of ways, from a simple fixed-length lanyard anchored to a single anchor, to a system including an adjustable lanyard running along
a second horizontal line anchored at both ends. When restraint lines are long, or
when using a running system, allowance must be made for any potential sag and
stretch of the line.
Assessors: shall verify candidates understanding and rigging of work restraint systems. The use of one point of attachment or single ropes for work restraint may be
appropriate.
WORK RESTRAINT / HORIZONTAL LIFELINES
WORK RESTRAINT/ HORIZONTAL LIFELINES
67
VERTICAL FALL ARREST SYSTEMS
VERTICAL FALL ARREST SYSTEMS
Vertical fall arrest systems are typical rigged on ladders and

open lattice structures to provide rope access workers with
a temporary fall arrest system whilst accessing a work area.
The user will attach to this system using an appropriate fall
arrest device which will automatically lock into place in the
event of a fall. Falls will be kept to a minimum and deviation from vertical climbing is limited. Temporary systems
will be made from rope however permanent wire and rail
systems are used.
A vertical fall arrest system can be used as an alternative to
fall arrest lanyards or self retracting life lines.
Vertical safety systems can be employed to create a moveable anchor point for fall protection. These can be either fixed
(Wire rope or Rail) or temporary (Textile rope or Webbing).
When using temporary rope based systems fall arrest consider the effects of sharp and abrasive edges at all points
between the anchor and the user.
When using a vertical fall arrest system it is possible to rig it
in a rig for rescue or releasable style.
Candidates: Level 2 and 3 candidates shall demonstrate

rigging a temporary fall arrest system to protect a vertical climb.
Trainers: should explain when it is appropriate to use such a system, the requirements for anchor strength and considerations for rescue.
Assessors: should ensure candidates take account of clearance distances and user
numbers.
68
Tensioned ropes
Tensioned ropes may be used horizontally to traverse a structure or diagonally to redirect the path of descent.
Tensioned lines are normally rigged
with one end of the ropes fixed in position, the other end is put through
a descender, as pictured above, to
allow the ropes to be tensioned and
released as required.
The ropes are tensioned with a 3:1
pulley system with 1 person pulling
by hand. It is important that when
the ropes are tensioned that they are
not over tensioned and place excessive forces on the anchor points.
When attaching to tensioned ropes 2 points of contact must be maintained, to share

the load equally on the system connectors should be around both ropes. This is normally achieved by using a long and a short cowstail. Always consider the use of a
releasable attachment.
Candidates: Level 2 and 3 candidates shall demonstrate rigging tensioned ropes at

any positional angle.
Trainers: should emphasise that potentially higher forces may be placed on the anchors due to the creation of wide rigging angles, and that ropes should be under as
little tension as possible. Options and methods for rescue should be discussed, particularly the incorporation of releasable rigging at one or both ends. Trainers should
explain how to share the technicians load across both ropes to reduce sag.
TENSIONED ROPES
When rigging horizontal tensioned ropes rope access technicians should pay close
attention to the angles of rigging, forces on the anchors and safe working loads of
the equipment used. A Level 3 should be able to demonstrate the calculations
involved with this type of rigging setup.
69
Forces on tensioned ropes

0kN
0kN
0kN
3.06kN
3.06kN
3.06kN
3.06kN
1kN
1.42kN
FORCES ON TENSIONED ROPES
1.42kN
1.42kN
1.11kN
1.42kN
1.11kN
1.11kN
1.11kN
1kN
The diagram above demonstrates the importance of sharing the load over both
ropes.
70
RIGGING FOR
RESCUE AND
HAULING
71
LOWERING
When using a descender as a lowering device, the manufacturers instructions may require the use of an
additional braking karabiner to increase control.
LOWERING
This can be achieved by passing the

tail end of the rope through a karabiner above the descender.
Petzl ID Descender, Shown with

additional braking karabiner
72
Hanging a hauling system or casualty from a releasable attachment is preferable to

having to changeover a locking jammer haul or lift a casualty again during a snatch
rescue.
When making a releasable attachment from a length of cord or a footloop it must not
be treated as a point of attachment. Rated slings are considered to be an attachment
whilst fully locked off, but not when released. It is advisable to back these up with a
long cowstail.
Fully rated systems such as a Petzl Grillon or a descender threaded on a length of rope
allow for longer lowers and are rated and can be treated as a point of attachment
RELESABLE ATTACHMENTS
RELEASABLE ATTACHMENTS
73
HAULING
Locking Devices
Any hauling system requires some way of locking the rope that is being hauled on.
This can be achieved by the use of purpose built self-locking pulleys, pulley and rope
grab combinations or a descender.
HAULING
Petzl Rescue Pulley

and Hand Jammer
Petzl ID Descender
Petzl Pro Traxion
The use of a self-locking pulley is a simple, and the most efficient way to set up a
hauling system, but its is difficult to lower a load once it has been raised.
Using a descender as the locking mechanism allows the hauling system to be converted to a lowering system quickly and easily, it does however create more friction
and requires more effort to haul a load.
74
HAULING
2:1 Hauling System
2:1 hauling systems are very efficient when rigged through a locking pulley (a descender creates too much friction for long hauls). The disadvantage of this type of
system is the amount of rope required (2 x the height of lift) and the increased
chance of tangles due to the loop in the system.
2:1 Hauling System
2:1 Hauling System
2:1 HAULING SYSTEM
A 2:1 with the descender at the bottom of the loop is a useful way of lifting a casualty short distances during snatch rescues.
75
HAULING
3:1 Hauling System
3:1 Hauling System shown with a Change of

Direction pulley.
This arrangement is very efficient for hauling
and uses less rope than a 2:1 system. If a
short lower is also required consider using a
grillon for your anchor or using a descender
on the safety line to aid easy changeovers.
If the system is mainly for lowering the locking pulley can be exchanged for a descender
3:1 HAULING SYSTEM
33 kg
100 kg
76
HAULING
Increasing the Mechanical Advantage
20 kg
100 kg
100 kg
5:1 Hauling System
9:1 Hauling System
Note: Both hauling systems use the same number of pulleys, but the different configurations make a difference to the effort required to lift the load.
MECHANICAL ADVANTAGE
11.1 kg
77
HAULING
FORCES IN HAULING SYSTEMS
Forces in Hauling systems
78
When using hauling systems with high mechanical advantages potential problems arise
where loads may become snagged on the structure. The load applied by the rescuer is multiplied through the system and creates a potential for failure of rope and equipment or further injury to a casualty, particularly where toothed ascenders are used. Consider the use
of a Shunt in place of the Basic ascender as pictured.
FORCES IN HAULING SYSTEMS
HAULING
79
HAULING
FRICTION IN HAULING SYSTEMS
Friction
In all hauling systems rigging angles

and friction will make a huge difference to the efficiency of the system.
Try and keep angles as small as possible and always use pulleys, simply
placing the rope through a karabiner
will virtually take all of the mechanical
advantage out of a system.
Also try to choose large diameter pulleys or pulleys with roller bearings,
often called Rescue pulleys they are
more efficient than the smaller Fixe
type pulleys.
80
Petzl ASAP
Petzl ID Descender
All hauling systems require a suitable back up system to be used.

A Petzl ID can be used as a back-up device in a haul system, this suffers from similar problems as the shunt as it can not be operated simultaneously with the haul
system. The ID can, however be converted to a hauling and lowering system if there
is a problem with the main hauling system or a second person wishes to haul and
make the haul easier.
A Petzl Shunt may be used as a back up device in a hauling system, during the haul
both the hauling and back-up rope must be operated independently of each other
which may be time consuming when hauling over a long distance.
A Petzl ASAP, when used as a back-up system may allow both the hauling and backup ropes to be taken in and lowered at the same time, but the ASAP has a tendency
to let rope run through it if not locked off.
BACK-UP SYSTEMS
BACK-UP SYSTEMS FOR HAULING AND LOWERING
81
HAULING
Basic Hauling
A basic hauling system is to be set up on a platform and a casualty raised up to the
platform level, manoeuvred over the edge, then lowered to the floor.
The rescuer must consider their own safety during this rescue, the rescuer must operate the hauling system from behind a fixed barrier or handrail, or consider the use
of work restraint/horizontal lifelines.
The hauling system that is used can be anyone of the systems shown on the pervious pages, and used with a suitable back-up system.
Where the casualty will have to be manoeuvred over and edge the use of a high deviation and/or a tag line may be considered.
The casualty is to be attached to the hauling system so that they are kept as upright
as possible during the haul and lower.
Hanging Haul
Rescue of a casualty suspended on a set of ropes, with both working and back-up
rope under tension, and must be hauled up to a safe area, there is no slack rope in
the system, but a spare rope is available for a separate hauling system. The rescuer
can use additional rope to create slack in the system and install a hauling system to
retrieve the casualty.
HAULING
Rescuer to position themselves at the casualties anchor points.

Set up two anchor point, one for the hauling system, one for the back-up system.
Attach the haul rope directly to the casualties harness, this will be done either
prior to ascending , by a person in the rescue team, or by the casualty if able.
In unusual situations where none of these are possible it may be an option to
send a weighted jammer down the casualties working rope until it hits the casualties attachment.
Install the rope in to the locking mechanism of the hauling system and remove
any slack.
Build the hauling system.
Raise the casualty up far enough to install the casualties back-up rope into the
hauling system back-up device.
Continue to haul the casualty.
Take care to keep slack in the back-up rope to a minimum.
82
Candidates: All candidates shall show awareness of the use of hauling systems for rescue.
Level 2 and Level 3 candidates shall demonstrate rigging of all three hauling systems and their operation to allow evacuation of a casualty to a platform or stance. Hauling exercises may be conducted
from platform(s) or suspended on equipment at height (hanging haul).
Trainers: Shall explain the advantages of a pre-rigged system and when an additional system
may be appropriate.
Trainers shall emphasize the use of a pulley system, the need for a suitable back-up and an understanding of mechanical advantages and loads on the equipment. Trainers should explain how to haul
the casualty to a platform stance and bring the casualty to rest on the platform. This may include moving the casualty over safety barriers and the use of a tag line.
Assessors: Shall look for the efficient implementation of the system and correct use of
equipment.
Assessors shall be satisfied that the candidate has a general awareness of the potential difficulties
that could be encountered and has an understanding of the mechanical advantages and loads on
the equipment, in particular, those that could result in equipment failure.
HAULING
Assessors should note that candidates need only demonstrate one hauling exercise at assessment, at the assessors discretion. A variety of methods is acceptable.
83
CROSS HAUL
A cross haul involves to use of two or more hauling systems to manoeuvre a casualty
from one position to another.
During this rescue, the rescuers may use a basic haul system from a platform or a
hanging haul, or a combination of haul systems.
The casualty should be attached to the hauling systems so that they are kept as upright as possible.
In a simple scenario one rescuer no1 will haul the casualty up whilst rescuer no2
takes in the slack rope.
Once the casualty has been raised up, rescuer no1 converts their hauling system to a
lowering system, rescuer no2 builds their haul system.
With careful hauling and lowering between the two rescuers the casualty can be
transferred horizontally to a new position.
Once the casualty is hanging on rescuer no2s system, rescuer no1s system can be
disconnected.
The casualty can now be move onwards with another hauling system or lowered to
the ground.
Throughout the rescue it is important to maintain constant communication between
the hauling/lowering teams.
CROSS HAUL
Rescuers must be aware of the loadings on the equipment and the angles created
between the two hauling systems, keeping the internal angles as small as possible.
Candidates: Level 2 and Level 3 candidates shall demonstrate a cross haul of a casualty
between two points.
Trainers: Should explain how two (or more) sets of haul/lower ropes and back-up systems are rigged
and connected to the casualty. The casualty shall be transferred horizontally using the two systems.
Assessors: Should look for a cross haul that avoids the potential for an out-of-control swing, (e.g. one
caused by the failure of a single item of equipment) by the use of an appropriate back-up. Where two
persons are involved in the cross-haul rescue, assessors should be satisfied that appropriate communication is maintained.
84
EXAMPLES OF CROSS HAUL SYSTEMS
Cross Haul operated form below.
CROSS HAUL
Cross Haul operated form above.
85
COMPLEX RESCUE SYSTEMS/ TEAM RESCUE
COMPLEX RESCUE SYSTEM/ TEAM RESCUE

During advanced rescues Level 3 candidates shall take account of the following:
Team management. Candidates shall make the most effective use of their given
team, taking into account the skill level of each member. Candidates shall position themselves so that they are in the most suitable place to co-ordinate the
work task and likely rescue scenario.
Communication. Candidates shall communicate their intentions within the team
so that each team member is clear on his/her role for the planned method of
work and rescue. Clear instructions shall be given to each team member during each stage of the team rescue. Consideration shall also be given to communicating with emergency services and other site personnel.
Equipment. Candidates shall select suitable and sufficient equipment for the given task, taking into consideration the competence of the individual team
members and compatibility of components.
Casualty management. Candidates shall demonstrate best practice when managing the casualtys needs, including keeping the casualty upright, providing
comfort measures (e.g. a work seat or stretcher) and limiting the time spent
immobile in suspension.
A level 3 rope access supervisor must be able to plan and manage a task and make
appropriate provision for rescue, using all team members.
Elements of the planning stage include, but are not limited to:
A risk assessment, which covers hazard identification, likelihood of an incident

occurring and control measures to minimise the risk.
Prior agreement of operating procedures.
Selection of competent personnel.
Communication.
Selection of appropriate equipment.
Specific procedures to deal with hazardous materials, machinery, fixtures and
tools, and environmental hazards.
A level 3 rope access supervisor should give a toolbox talk before the start of the exercise to ensure all team members know what they have to do and how the rescue
system works. A level 3 may have to demonstrate to other team members.
A level 3 supervisor should give clear instructions throughout the exercise. Do not assume that other team members, regardless of level of training or experience will
know what steps to take. Eg. Do not say Clip on that karabiner, instead say Clip
that karabiner to the casualties D ring and screw up the gate. Then ask them to hold
it up so you can see it , to check it.
86
Trainers: Should note that this exercise is designed to test the candidates ability both to create
and implement a rescue plan.
Assessors: Should plan this exercise to allow candidates between 45 and 60 minutes to plan and
rig the exercise, and 15 to 30 minutes for the execution of the rescue. Assessors may use this exercise to check for a satisfactory completion of IRATA form 061, Job planning.
COMPLEX RESCUE SYSTEMS/ TEAM RESCUE
Candidates: Level 3 candidates shall demonstrate planning and rigging a complex rope access system, and then carrying out the associated team exercise. The system should allow evacuation of a
casualty around three-dimensional obstacles.
87
88
ROPE ACCESS
MANOEUVRES
89
ROPE ACCESS MANOEUVRES

The aim of this section is to lay out the individual rope access manoeuvres required by
all rope access technicians using a step by step approach, for level 1 candidates, all
manoeuvres should be completed on a pre-rigged course. Level 2 and 3 candidates
may be required both to rig ropes, and then to perform manoeuvres on their own rigging.
Use of the back-up device
The back-up device, which is connected to the safety line, is used to protect against
falls before,
during and after attachment of the rope access technician to the working line. It
should be the first
item to be attached to the anchor lines, i.e. before ascending or descending devices,
and the last item to be removed at the point of egress, i.e. after removing the descending device or ascending devices. The back-up device should be managed at all times in
such a way that the potential fall distance is minimized.
All candidates shall demonstrate throughout the whole of the assessment the use of
a back-up device (and device lanyard, where appropriate) in accordance with best
practice, the IRATA trainer member companys risk assessment and the manufacturers instructions. This includes checking the position and function of the back-up device at appropriate times.
Ascending
Climbing a rope is the second basic technique in rope access and is accomplished by
the alternate use of two ascenders, typically a chest ascender and a handled ascender
with a footloop.
All candidates shall demonstrate attaching ascenders and the back-up device to a set
of pre-rigged ropes, ascending, and detaching from the ropes to another system or
safe area.
Descending
The controlled descent of ropes is a core technique in rope access. Rope access technicians must be able to control their speed and stop as required.
All candidates shall demonstrate attaching a descender and back-up device to a set of
pre-rigged ropes. Before descending candidates shall demonstrate checking the position and function of the back-up device. During descent candidates shall demonstrate
safe control of the tail rope.
Candidates shall demonstrate stopping and locking off the descender device.
Changeovers
Changing from ascent mode to descent mode, and vice-versa, is an essential basic
technique in rope access, and forms the basis of many other manoeuvres.
All candidates shall demonstrate changing from ascent to descent and vice-versa.
The typical methods of descending and ascending ropes will not be covered in this section as they are covered in detail in IRATA ICOP Annex K.
90
SINGLE ANCHOR DEVIATIONS
IN ASCENT
Ascend the rope to the deviation
Push the deviation sling up until it is horizontal, you
may need to ascend further.

Move the back up device to a position as high as it
will go.
Take hold of both ropes underneath your devices and
clip them into the spare karabiner in the deviation

sling.
Ensure the karabiner is locked.
Pull yourself along the deviation sling and remove the
karabiner above your devices

Using the deviation sling and the rope slowly lower
yourself out to the vertical, you will now be above the

deviation sling.
IN DESCENT
Descend to a position level with the deviation anchor
point; be careful not to descend too low.

Make sure the spare karabiner in the deviation sling
is
unlocked.
Using the rope and the deviation sling, pull yourself
towards the deviation anchor point.

When the sling has gone slack, clip the spare karabiner around the ropes above
your devices.
Ensure the karabiner is connected around both ropes and is locked.
Undo the lower karabiner and remove the ropes.
Candidates: All candidates shall demonstrate passing a single-anchor deviation in both ascent and
descent modes.
All candidates shall demonstrate passing a double-anchor deviation in both ascent and descent
modes.
Trainers: Shall ensure all candidates understand the two different types of deviations and the need for
single or double protection as appropriate. Trainers shall stress the need to avoid out-of-control swings
when passing deviations. Normally, no equipment needs to be removed from the working line or safety
line in order to pass a deviation.
Assessors: Should note that a small out-of-control swing shall be considered a minor discrepancy.
However, a swing that could cause injury to personnel or damage to equipment or property shall be
considered a major discrepancy.
SINGLE ANCHOR DEVIATIONS
Single-anchor deviations are used to deviate the ropes (or the working line alone) by a
small angle only. Single-anchor deviations are only appropriate where their failure would
not result in serious consequences (such as a large swing into a structure, or contact
with a sharp edge) and are normally rigged as a single anchor system. The sling is also
rigged with a spare karabiner at the end of the deviation.
91
DOUBLE ANCHOR DEVIATIONS
DOUBLE ANCHOR DEVIATIONS
Double-anchor deviations may deviate

the ropes by a greater angle and distance than a single-anchor deviation,
and allow the ropes and user to be protected against more serious hazards
such as a sharp edge or a large swing
into a structure. Such a deviation utilizes
a double anchor system, with suitably
rated anchors and connection components, to provide protection against failure of any one item. Where a large angle
is created, users should consider whether a re-anchor may be more appropriate.
IN ASCENT
Ascend the rope to the deviation
Push the deviation sling up until it
is horizontal, you may need to ascend further.

Move the back up device to a posi
tion as high as it will go.
Attach a long cowstail to the first sling or anchor point.
Remove the deviation sling and replace it around both ropes beneath your ascend
ers.
Remove the long cowstail and connect it to the second sling or anchor.
Remove the second deviation sling and replace it around both ropes beneath your
ascenders.
Remove the long cowstail
Using the deviation sling and the rope slowly lower yourself out to the vertical, you
will now be above the deviations.

IN DESCENT
Descend to a position level with the deviation anchor point; be careful not to de
scend too low.
Using the rope and the deviation sling, pull yourself towards the deviation anchor
point.
Attach a long cowstail to the first sling or anchor point.
Remove the deviation sling and replace it around both ropes above your descend
er.
Remove the long cowstail and connect it to the second sling or anchor.
Remove the second deviation sling and replace it around both ropes above your
descender.
Remove the long cowstail.
You will now be below the deviations.
92
ROPE TO ROPE TRANSFER

During the rope to rope transfer technicians must be aware of a single item failure
causing an out of control swing.
The two sets of ropes being used must be joined securely together to enable the technician to move between them.
This manoeuvre will be carried out without extra equipment. As no additional backup
devices are available connect to an alpine butterfly knot with a cowstail.
Whilst on a set of ropes do a change over into descent equipment.

Tidy the two sets of ropes, one set on one side of the body, the other set on the
other side of the body, this will help to avoid tangles later on.
Choosing one rope as the new working line place this into the chest ascender
and pull through the slack, being careful not to deviate too far from vertical.
Place the hand jammer above the chest ascender.
Place the additional alpine butterfly knot into the backup rope, connect a
cowstail to the alpine butterfly ensuring slack is kept to a minimum.
Slowly descend or ascend to transfer your weight onto the new set of ropes.
When the new ropes are fully weighted and the old ropes have gone slack remove the descender and backup device.
You are now on a new set of ropes.
Candidates: Shall demonstrate transferring from one set of ropes to another set of ropes, which may
be at any distance apart.
Trainers: Shall draw attention to the possibility of out-of-control swings, and the need for four points of
attachment where necessary. Candidates may use two back-up devices but must have the practical
knowledge of using an appropriate knot as the secondary back-up.
Assessors: Should note that a variety of recognised techniques are acceptable, but failure to install or
maintain appropriate back up on one side of a wide rope-to-rope transfer leaving the possibility of a
large out-of-control-swing shall be considered a major discrepancy.
ROPE TO ROPE TRANSFER
93
RE-ANCHORS
A re-anchor is a technique for re-anchoring the ropes part way down, either to avoid a
hazard or to move you in to a better work position. A re-anchor is also an effective
measure of reducing the rope stretch on a long drop. Both long and short re-anchors
can be approached following the method detailed below.
IN ASCENT
Ascend the rope to the intermediate anchors.
Change over into descent equipment
Attach a long cowstail into the anchor point.
Remove your back-up device and replace it on one of the ropes above the an
chors.
Stand up in your foot loop, open your chest ascender and remove the rope.
Place the other rope from above the anchors into the chest ascender and pull
through the slack.

Remove your hand jammer and place it above your chest ascender.
Ascend the rope until you can reach to remove your long cowstail.
You will now be above the re-anchor.
RE-ANCHORS
IN DESCENT
Descend until level with the intermediate anchors.
Pull yourself in and attach a short cowstail to the anchors.
Lower yourself down until you are suspended by the short cowstail.
Remove your descender and replace it on one of the ropes below the anchors.
Remove your back-up device and replace it on one of the ropes below the an
chors.
Attach your foot loop to the anchors, stand up and remove the short cowstail.
Remove the foot loop.
You will now be below the re-anchor.
Candidates: Shall demonstrate, in both ascent and descent modes, passing a re-anchor whose offset
shall be less than 1.5 metres. Level 2 and 3 candidates shall demonstrate passing a re-anchor whose
offset may be any distance apart.
Trainers: Shall emphasise that a back-up must protect any potential out-of-control swing or movement
that may cause injury to personnel or damage to equipment or property. Therefore, a wide re-anchor (or
loop) may require techniques similar to a rope-to-rope transfer, and the use of two back-up devices.
Assessors: Should note that a variety of techniques are acceptable for this manoeuvre. Assessors
should note that a small out-of-control swing shall be considered a minor discrepancy. However, a
swing that could cause injury to personnel or damage to equipment or property shall be considered a
major discrepancy.
94
PASSING MIDROPE KNOTS

In this manoeuvre it is assumed that knots are present in both working and backup
ropes, the knot is an alpine butterfly with an additional overhand knot used to isolate a
damaged section of rope. The knots are at the same level in both ropes. Knots in ropes
may also be used to join ropes together. Whenever a joining knot is tied, a loop should
accompany it to assist the technician in passing the knot(s). The implications of tying a
knot mid rope in a rescue situation should be considered.
IN ASCENTWORKING ROPE
Ascend the rope to the knot.
Install the descender underneath the chest ascender and lock off.
Remove the hand jammer and place above the knot.
Stand in the foot loop, remove the chest ascender and replace above the knot.
Remove the descender.
IN DESCENT WORKING ROPE

Descend to the knot.
Change over from descent to ascent.
With the descender now unloaded, replace it below the knot.
Descend a short distance on the ascenders to the knots.
To reduce the chance of hanging from the backup device it may be necessary to
move it now.
Stand in the footloop and remove the chest ascender, lower yourself onto the de
scender.
You should be able to retrieve your hand jammer easily.
IN DESCENT BACK UP ROPE

Using the shortest possible cowstail clip into the safe loop between the alpine
butterfly and the overhand knot.

Remove the backup device and place it below the knot.
Remove the cowstail.
Candidates: Shall demonstrate passing such a knot in both ascent and descent. Knots may be in either
one or both ropes, and may be level or offset. Level 2 and 3 candidates shall demonstrate identifying,
isolating and passing minor damage in a rope by tying appropriate knots (Level 1s should be capable of
doing so under supervision). In addition, Level 2 and 3 candidates may be required to tie knots to join
ropes.
Trainers: Shall emphasise that in the workplace damaged rope should be replaced as soon as possible.
Knots may complicate rescue; therefore knots joining ropes should be avoided wherever possible, and
knots used to isolate damaged rope shall be considered an emergency temporary measure. Single knots
used to isolate damage should not be used as an attachment.
Assessors: Should note that a variety of techniques and knots are acceptable for this manoeuvre. Damage to rope may be simulated with the use of marker tape or similar methods.
PASSING MID-ROPE KNOTS
IN ASCENT BACK UP ROPE

Ascend the rope to the knot.
Move the backup device as high as possible below the knot.
Using the shortest possible cowstail clip into the safe loop between the alpine
butterfly and the overhand knot.

Remove the backup device and place it above the knot.
Remove the cowstail.
95
EDGE OBSTRUCTIONS
EDGE OBSTRUCTONS
Always attach to the ropes from a safe area where there is no risk of a fall occurring,
if this is not possible then work restraint or fall arrest techniques may be utilised to
reach the work area safely. When ascending over an edge care must be taken not to
have a potential for falls onto ascenders. Consider attaching with a long cowstail or
changing onto a descender. The use of an additional etreir, tied to the rope may assist with passing an edge obstruction.
Candidates: Shall demonstrate passing a top edge obstruction, where anchor points are
at or near right angles to the line of descent, in both ascent and descent modes.
Trainers: Shall ensure candidates take care to attach their equipment correctly before
approaching the edge. Trainers shall draw attention to hazards associated with edges, including rope
stretch and the potential for shock loads.
Assessors: Should look for appropriate safe control during this manoeuvre, and avoidance of shock
loads and cross loads on equipment.
WORKSEAT
USE OF WORK SEATS

The use of a seat is to aid the comfort of the rope access technician only. It must
never be used as a primary means of support, for this reason a work seat is not considered an item of PPE and therefore requires no testing or certification
Candidates: Shall demonstrate the correct attachment and use of a work seat.
Trainers: Shall emphasise that the work seat is not typically part of the fall protection system, but is
intended to provide additional comfort only.
Assessors: Should note that a variety of seats and techniques are acceptable.
96
PASSING MID ROPE PROTECTION

Wrap-around canvas rope protectors may be installed mid-rope to protect the
ropes against minor abrasive hazards.
IN DESCENT
Descend to the rope protectors
Open the rope protectors, whilst holding yourself off the structure
Remove the rope protectors and replace securely on the ropes above your de
vices
As you ascend re-secure the rope protectors around each rope, ensuring the
rope protectors protect the ropes from abrasion for the next climber.
Candidates: Shall demonstrate passing and replacing mid-rope protection in either ascent
or descent. Normally separate protectors should be used for each rope.
Trainers: Should ensure that candidates are able to, pass the protectors and reinstate them
in the appropriate place, including securing them to either structure or rope as required. Trainers
should ensure such exercises are carried out in a realistic practical setting, i.e. at a potential contact
hazard on a structure.
Assessors: Should look for safe and appropriate use of rope protectors and their correct
installation.
PASSING MID ROPE PROTECTOIN
IN ASCENT
Ascend the ropes to the bottom of the rope protectors.
Open the rope protectors, whilst holding yourself off the structure.
Remove the rope protectors and replace securely on each rope underneath your
devices.
Re-secure the rope protectors around each rope, ensuring the rope protectors
protect the ropes from abrasion for the next climber.
97
98
CLIMBING
TECHNIQUES
99
HORIZONTAL AID CLIMBING
The use of aid climbing techniques enable rope access technicians to reach parts of a
structure without the use of ropes, instead fixed (bolts) or movable anchors (tape
slings or wire strops) are used. Additional foot loops or etrier are often required for aid
climbing.
HORIZONTAL AID CLIMBING
A typical and efficient setup utilises an etrier on the end of each of your two long
cowstail and a spare karabiner connected to your short cowstail.
These cowstails are then connected to your anchors with the left cowstail on the left
anchor.
The short cowstail connected to the middle anchor
And the right cowstail on the right anchor.
To pass an obstruction you must always maintain two points of attachment with the
structure, by using three cowstails to climb with this ensures you always have two
points of attachment leaving one cowstails to move past the obstruction.
Candidates: Shall demonstrate horizontal aid climbing, progressing primarily in

suspension by moving along:
a) a series of fixed anchors;
b) with the use of moveable anchors such as strops or slings.
Trainers: Shall emphasise the need for a minimum of two independent attachments at all
times; therefore the use of at least three lanyards is required. Trainers shall emphasise the need to
select suitably positioned and sufficiently strong anchors, and also the need to minimise potential fall
distances and shock loads.
Assessors: Should be aware that this exercise is intended to demonstrate the candidates
ability to both move across the structure, and to change from aid to ropes and vice versa.
Suitable aid climbs for assessment should cover at least five metres horizontal movement,
and with movable anchors should pass at least two separate obstructions.
100
VERTICAL AID CLIMBING
Candidates: Level 2 and 3 candidates shall demonstrate vertical aid climbing, progressing primarily in
suspension in an upward direction.
Trainers: shall explain the suitability of different types of lanyards, and emphasise the need
to minimise potential fall factors, distances and shock loads.
Assessors: should note that a variety of lanyards and techniques are acceptable. Suitable aid climbs for
assessment should cover at least three metres vertical distance.
VERTICAL AID CLIMBING
When aid climbing vertically the same procedure is

used as for horizontal aid climbing. Consideration
needs to be made to the possibility of a failure of
equipment resulting in a fall factor of above 1. An
energy absorbing lanyard can be used to allow for
the higher forces involved, however the increase in
clearance distances required must also be considered.
101
CLIMBING WITH FALL ARREST LANYARDS
CLIMBING WITH FALL ARREST LANYARDS

Fall arrest lanyards can only be used with a full body fall arrest harness to EN361.
Heightworks Ltd and IRATA recommend the use of a front (sternal) fall arrest point,
although a rear (dorsal) fall arrest point may be used in certain situations. Whilst using fall arrest lanyards only one lanyard needs to attached to the structure at a time,
this is one point of attachment; the other point of attachment is your hands and feet.
It is important that the fall arrest lanyards selected will arrest the fall before you hit
the ground or structure. Use as short lanyards as practical and always attach them
as high as you can in relation to your own body. Ensure that connectors on the lanyard are compatible with the structure.
The unused leg of a Y shaped lanyard must not be attached back to your harness,
this can potentially isolate the energy absorber and prevent it from extending during a
fall.
Any attachment point must be unquestionably reliable and fixed, attachment to vertical and diagonal steelwork should be avoided as this can result in increased fall factors (>FF2).
When combining fall arrest lanyards with a work positioning lanyard, attach the work
positioning lanyard to an independent attachment where it cannot slip. Do not remove your fall arrest lanyards. It is important that work positioning equipment does
not become slack as they do not include an energy absorption.
Candidates: All candidates shall demonstrate a vertical climb with the use of a pre-installed temporary or permanent fall arrest system.
All candidates shall demonstrate climbing using a twin-tailed fall arrest lanyard, maintaining appropriate attachments at all times. Candidates shall demonstrate changing to and from work positioning (i.e.
supported by a work positioning lanyard such as a cows tail) during this exercise.
Trainers: Should ensure candidates understand the specific equipment requirements of fall arrest
systems, including a full body harness, an energy absorber and appropriate connectors, which meet
the requirements of recognized standards.
Trainers should ensure candidates are able to identify safe anchor points, that they connect to them
correctly and that they understand the need for an adequate clearance distance below. Specific
guidance on clearance distances is typically provided in manufacturers instructions.
102
A fall factor measures the theoretical severity of a fall and is calculated using the following formula:
FF=
Length of fall
Length of rope or lanyard
EN355 Energy absorbing lanyards are designed to reduce the impact force to below
6KN when using a lanyard of maximum length 2m and a 100kg load.
The distance of fall should be kept to a minimum, the less distance of fall the less energy will be created this will affect how far the energy absorber deploys and have an
impact on clearance distances. Users of fall arrest lanyards should use lanyards that
are as short as practical for the task and aim to keep their fall factor to a maximum of
1. Where fall factors of more than 1 are unavoidable extra care must be taken with regard to any obstructions in the path of the fall.
Extreme care must be taken when lanyards with no energy absorbers are used. Falls of
any distance are forbidden and longer falls (2-4m) are likely to cause serious or fatal
injuries.
When using dynamic rope cowstails for fall protection the maximum permissible fall
factor is 1. Consideration must be made as to the length of the cowstail (approx 60cm)
and the knots used to terminate the cowstail. A barrel knot will provide more shock absorbency than an overhand or figure of 8 knot.
Guidance on fall factors, clearance distances and associated risks is provided in ICOP
Part 3, Annex Q.
FALL FACTORS
Heavy (>100kg) users of fall arrest equipment must be careful as not to overload the
energy absorber during a fall. A 120kg person can fall a maximum of 3.3m onto a 2m
lanyard in order to create a load of less than 6KN, this is just above a fall factor 1.5. It
can be advantageous to use shorter lanyards which will not allow a fall greater than
3.3m to be created (1.65m with a full sized energy absorber).
103
FF 0
FF 1
It is acceptable to fall onto a

work restraint , fall arrest or dynamic rope lanyard (cowstail)
FALL FACTORS
It is acceptable to fall up to 2m
onto a fall arrest lanyard or 60cm
onto a dynamic rope cowstail
(FF1). It would be advisable to
use Barrel knots in your cowstails
to minimise shock loads
FF 2
It is acceptable to fall up to 4m (FF2)onto a fall arrest lanyard although this is not recommended and
measures should be put in place to prevent this.
Although the lanyard is designed to hold the fall you
are likely to strike the structure during the fall and
be left in an exposed position post fall
Where fall arrest lanyards are used the energy absorber will extend in order to dissipate energy. Care
should be taken in ensuring that there is adequate
clearance below the operative. (see clearance distances overleaf)
104
LANYARD LENGTH
1.5M
FREEFALL DISTANCE
3M
OVERALL CLEARANCE DISTANCE = 6.5M
ABSORBER EXTENSION
APPROX 1.5M
BODY LENGTH
2M
This shows a worse case scenario for a 1.5m lanyard, a 2m lanyard positioned for a
fall factor 2 fall would result in worse fall in terms of fall distance.
The clearance distance can be greatly reduced by limiting fall factors to 1 and reducing the length of the lanyards. By reducing the freefall distance you reduce the
energy in the fall , this will result in less extension from the energy absorber.
CLEARANCE DISTANCE
FF 2
105
LANYARD LENGTH
1.5M
FREEFALL DISTANCE
3M
FF 2
CLEARANCE DISTANCE
OVERALL CLEARANCE DISTANCE = 6.5M
ABSORBER EXTENSION
APPROX 1.5M
BODY LENGTH
2M
This shows a worse case scenario for a 1.5m lanyard, a 2m lanyard positioned for a
fall factor 2 fall would result in worse fall in terms of fall distance.
The clearance distance can be greatly reduced by limiting fall factors to 1 and reducing the length of the lanyards. By reducing the freefall distance you reduce the
energy in the fall , this will result in less extension from the energy absorber.
106
Various techniques exist for direct progression on a structure using personal fall protection equipment. These techniques can be broadly split into two methods:
Aid climbing suspended by work positioning lanyards (such as cows tails);
Climbing with fall arrest equipment (such as energy-absorbing lanyards or preinstalled fall arrest systems).
In some situations, a combination of the two methods may be used. Guidance on other methods, such as lead climbing, is provided in ICOP Part 3, Annex L.
LEAD CLIMBING
Although lead climbing will not form part of a IRATA assessment, it is recommended
that Level 3 candidates read and understand this annex.
107
108
ROPE
RESCUES
109
PRINCIPLES OF RESCUE
Before rope access work begins all team members should fully understand the rescue plan should an incident occur. A thorough rescue plan should be part of the risk
assessment and method statement.
All team members should be briefed on:
Their role and responsibilities during a rescue
Sequence of events during a rescue
Location of rescue and first aid equipment
Communications, between rescue team members and emergency services
All team members should fully understand the techniques involved in carrying out a
rescue. If the rescue plan is particularly complex then a rescue drill maybe required.
Rescue equipment and a first aid kit should accompany the rope access team, this
should include enough equipment to retrieve a casualty from any rope access situation. Dedicated rescue equipment should not be used for any other task.
PRINCIPLES OF RESCUE
If the Risk Assessment dictates that in the event of a rescue being required the rescuer cannot access the casualtys position, or that the time required setting up and implementing a rescue would prove too lengthy, a rescue system should be pre-rigged. If
deemed necessary, this may be attached to the operative throughout the work task or
ropes could be rigged to include the haul system.
Before any rescue is implemented it is important that the team supervisor or rescue
co-ordinator assesses the situation, then tries to communicate with the suspected
casualty to ascertain his/her condition and to decide whether a rescue is necessary.
The rescuers orders of priorities are:
Not to endanger themselves
To prevent further injury to the casualty
To evacuate the casualty to the point of safety as soon as possible, where essential
and effective treatment may be administered.
Casualty management must be constantly addressed throughout any rescue, with the
rescuer taking sufficient steps so as not to worsen any injury sustained by the casualty. The casualty should be suspended by the sternal attachment point as this may
help to manage the casualties airway. The casualty should be protected against impact with any obstacles whilst the rescue is in progress.
It is the responsibility of the rope access team to provide first aid to a casualty until
medical care arrives. The rope access team must insure that suitable equipment is
at the work site and that the team are suitably trained. Location and work activity will
determine what measures are implemented.
110
DESCENT RESCUE
A snatch rescue may be implemented in the unlikely event of a casualty becoming
incapacitated. This may be done on a separate set of ropes or using the casualties
ropes.
All ways start in descent mode, at level 1 the casualty will also be in descent.
Same rope:
Casualty in descent mode
Ascend the casualties ropes using the casualties backup rope as your working
rope and the casualties working rope as your backup.

Ascend the casualties ropes until level with the casualty.
It may be necessary to move your hand jammer above the casualties backup
device to prevent them becoming locked together.

Use a karabiner around the casualties chest harness and clip it around the
working rope.
This will keep the casualty upright.
Ensure all ropes are cleared from between rescuer and casualty to prevent tan
gles whilst descending.
Connect a long cowstail between you and the casualties waist D ring.
Using your short cowstails connect to the karabiner of the casualties descender.
Remove your backup device.
Descend on your ascenders to transfer your weight onto the casualties de

scender.
Pass the breaking rope through a karabiner connected to a structural part of
the harness below the descender (NOT the gear loop).

Descend under control.
Candidates: All candidates shall demonstrate the rescue of an unconscious casualty (i.e. feigning
immobility) in descent mode, from an adjacent set of ropes.
Level 2 and 3 candidates shall demonstrate a descent rescue using the casualtys own ropes.
Trainers: Shall emphasise that candidates may be required to approach the casualty from
above or below.
Assessors: Should check that correct attachments are maintained and that a controlled
descent is made.
DESCENT RESCUE
Separate rope:
Descend until level with the casualty.
Ensure all ropes are cleared from between rescuer and casualty to prevent tan
gles whilst descending.
Connect a long cowstail between you and the casualties waist D ring.
Using your short cowstail or 2 karabiners, make a connection to the karabiner
from your descender to the ventral attachment point to the casualties chest D
ring.
Lower the casualty slowly to transfer their weight onto your descender
Your casualty will now be in an upright position, suspended from your descend
er.
Pass the breaking rope through a karabiner connected to a structural part of
the harness below the descender (NOT the gear loop).

Descend under control, the casualties backup device may be left in place as
additional security.
111
ASCENT RESCUE
Rescue of a casualty from their ascenders. This may be done on a separate set of
ropes or using the casualties ropes. This technique uses a counterbalance to lift the
casualty a short distance. Note: this does not create any mechanical advantage.
ASCENT RESCUE
Position yourself at the same height as the casualty.

Remove the casualties hand jammer and then Install a second back-up device
onto the rope above the casualties chest jammer.
Changeover onto your descender and re-position yourself.
Attach the casualties descender to their chest attachment point and thread
the casualties working line in to it, and lock it off.
Thread the your foot loop through the karabiner on your second back-up device
above the casualty and connect it to the top of their chest ascender/maillon.
Stand up with a straight leg, all your weight must be pushing down your leg
must be straight.
Reach down and pull up on the casualties harness, the casualty should raise a
short distance and the rope in the chest ascender go slack.
Remove the rope from the chest ascender, pull any slack rope through the descender and lock it off.
Sit down and remove the foot loop.
You and the casualty should now be both on descenders with high back up devices.
The rescue can now completed the same as a snatch rescue form a descender.
Candidates: Level 2 and 3 candidates shall demonstrate a mid-rope rescue of an unconscious

casualty, i.e. feigning immobility, while suspended on ascenders. The rescuer should be able to
ascend or descend to a casualty, de-weight the casualty and descend to the ground.
Trainers: Shall ensure that the candidate is able to demonstrate a rescue from ascent mode
of an unconscious casualty, using both of the following methods:
a) from a separate set of ropes;
b) using the casualtys own ropes.
Assessors: Should note that candidates need only demonstrate one rescue from ascent
during assessment, at the assessors discretion.
112
DEVIATION RESCUE
Rescue of a casualty from above a deviation.
There are many different ways to pass through a deviation with a casualty.
If the deviation is small it may be possible to use the same technique as the rope
manoeuvre.
For a larger deviation, an adjustable sling, such as a mariners knot may be used;
Descend with the casualty until you are level with the deviation.
Take a spare sling and a karabiner, clip the karabiner and the sling around the
ropes above you.
Thread the other end of the sling through the spare karabiner in the deviation
sling.
Keeping the sling as neat as possible, wrap the end of the sling between the
karabiner around the ropes and the karabiner in the deviation.
This should pull you and the casualty towards the deviation and release the
tension on the karabiner in the deviation below you.
To tie off the mariners hitch, wrap the tail end of the sling around the sling between the karabiners, then push the end through the middle of the sling and
secure with a karabiner.
You should now be underneath a new deviation with no weight on the old deviation sling.
Remove the old deviation karabiner.
Descend to the ground under control.
Candidates: Level 2 candidates shall demonstrate descending with a casualty through a single positional deviation.
Level 3 candidates shall demonstrate descending with a casualty through a double deviation.
Trainers: should emphasise the avoidance of out-of-control swings, loading of the casualtys cowstails, and potential slack in the back-up line.
Assessors: should look for the avoidance of loading of the casualtys cows-tails.
DEVIATION RESCUE
113
ROPE TO ROPE TRANSFER RESCUE

Descending with a casualty and transferring from one set of ropes to another.
The rescue is carried out in the same way as a basic rope to rope transfer, this
rescue is made easier by the use of additional equipment from the casualty.
ROPE TO ROPE TRANSFER RESCUE
Descend under control with the casualty, stop and lock off the descender.
Ensure the back up device is in a high position.
Sort out both sets of rope to ensure there are no tangles during the manoeuvre.
Take the spare descender and connect it to the harness next to the loaded descender, making sure both casualties and rescuers connections are in the
same karabiner.
Thread the new working rope into the descender and pull through as much
slack rope as possible.
Install the spare back up device on to the new back up rope.
Descend/ascend across on to the new ropes, remove the attachments from
the original ropes.
You should now be on a new set of ropes and tangle free.
Candidate: Level 2 and 3 candidates shall demonstrate transferring, with a casualty, from one set of
ropes to another set of ropes rigged more than 3 metres apart.
Trainers: should emphasise:
a) good casualty management;
b) maintaining four appropriate points of attachment when required;
c) potential use of the casualtys personal equipment;
Assessors: should look for a rope-to-rope transfer that avoids the potential for an out-of control swing,
e.g. one caused by the failure of a single item of equipment, by the use of appropriate back-ups.
114
RESCUE OF A CASUALTY FROM ABOVE A RE-ANCHOR.
Ascend or descend to the casualty until you are level with them.
If the casualty is in ascent mode then an ascent rescue will have to be performed first.
With the casualty on their descender, and the rescuer on a descender transfer
one person so that both casualty and rescuer are suspended by one descender
and a back-up device. Whilst connecting to the casualty ensure that you sort
out both ropes so there are no tangles between you and the re-anchor.
Descend to the re-anchor using extra friction.
Stop when level with the re-anchor and make sure both casualty and the
rescuer are on the same side of the loop.
Take the spare descender and connect it to the harness next to the loaded
descender, making sure both casualties and rescuers connections are in the
same karabiner.
Thread the rope from under the re-anchor into the descender and pull through
as much slack rope as possible.
Install the spare back-up device onto the back-up rope below the re-anchor.
Descend/rope to rope transfer across on to the ropes below the re-anchor, remove the gear from above the re-anchor.
You should now be below the re-anchor and tangle free.
Candidates: Level 2 and 3 candidates shall demonstrate descending with a casualty through a small re
-anchor, with an offset of no more than 1.5 metres.
Trainers: should emphasise the avoidance of tangles with the re-anchor loops and loading
of the casualtys cows-tails.
Assessors: should look for a lack of tangles and the avoidance of loading of the casualtys
cows-tails.
RE-ANCHOR RESCUE
This rescue is made easier by the use of additional equipment from the casualty.
Rescuers should be aware of the possibility of tangles of ropes in this manoeuvre,
especially descending into the loop of the re-anchor and ending up with the casualty
on one side and the rescuer on the other.
115
LARGE RE-ANCHOR RESCUE

Rescue of a casualty through a large re-anchor, sometimes called a loop rescue.
This rescue can be made easier during the rigging stage of setting up your worksite,
by making the loops of the re-anchor as large as possible. The smaller the loops the
harder it is to move you and a casualty through them. The move through the loop is
treated the same as a rope to rope transfer, the main difference being that you will
have to climb one side of the loop to prevent yourself and the casualty becoming
stuck. Do not descend into the bottom of the loop.
LARGE RE-ANCHOR RESCUE
If the casualty is in the bottom of the loop in may be necessary to ascend one
side of the loop with the casualty in order to gain some slack in the system.
Once at the casualty, both casualty and rescuer need to be suspended from a
descender and a back up device, leaving one set of equipment spare.
Sort out the loop of rope to ensure there are no tangles during the manoeuvre.
Take the spare descender and connect it to the harness next to the loaded descender, making sure both casualties and rescuers connections are in the
same karabiner.
Thread the rope from the other side of the loop into the descender and pull
through as much slack rope as possible.
Install the spare back up device on to the other side of the loop.
Descend/rope to rope transfer across on to the other side of the loop, you may
need to use a spare jammer and pulley as a 2:1 pulley system to climb the
ropes to avoid the bottom of the loop.
You should now be on one side of the loop and tangle free.
You may have to complete another rope to rope transfer onto ropes that reach
the ground.
116
MID-TRANSFER RESCUE
Rescue of a casualty from the mid point of a rope to rope transfer.
Candidates: Level 3 candidates shall demonstrate the rescue of an unconscious casualty, i.e. Feigning immobility, who is suspended:
a) at any point during a wide (more than 3 metres apart) rope-to-rope transfer;
b) at any point whilst crossing a wide (more than 1.5 metres offset) re-anchor (aka a loop).
The candidate shall attend to the casualty, manoeuvre them out of the situation, and return them to a
safe platform such as the floor.
Trainers: shall stress the consequences of failure of any one item of equipment and the
need for four points of attachment.
Assessors: should look for a rescue that avoids the potential for an out-of-control swing,
e.g. one caused by the failure of a single item of equipment, by the use of an appropriate back-up.
Assessors should note that candidates need only demonstrate one mid-transfer rescue
during assessment, at the assessors discretion.
MID-TRANSFER RESCUE
Ascend or descend to the casualty until you are level with them.
Position yourself level with the casualty on your descender,
Using a long cowstail make a connection to the casualties waist D-ring.
Attach an additional descender to the casualties waist D-ring, thread the rope from
the chest ascender into the descender.
Using a counterbalance remove the casualties chest ascender.
Using a short cowstail make a connection into both of the casualties descenders.
You should now be hanging below the casualty using their equipment.
Continue to descend to complete the rope to rope transfer.
Descend to ground under control.
117
RESCUE PASSING MID ROPE KNOTS

Rescue of a casualty and descend a set of ropes with knots tied below the rescuer
and casualty. The knots are to isolate damaged rope and cannot be removed. The
knots may be at the same height or off set.
RESCUE PASSING MID ROPE KNOTS
Descend to the knots under control.

Do not abseil on to the knot, leave a short distance between the descender
and the knot.
Attach a rope grab to the rope above your descender. Install a releasable attachment to the rope grab and to your loaded attachment point.
Install a second descender to the working rope directly below the knot.
Transfer your weight onto the releasable attachment and remove the original
descender.
Lower your weight onto the descender below the knot.
Pass knot on back-up rope.
Candidate: shall demonstrate descending with a casualty passing a set of mid-rope

knots, and taking into account any stretch in ropes. The rescuer should take full advantage of the
casualtys personal equipment.
Trainers: should ensure that knots are pre-tied in the working and back-up ropes. These
knots may be offset or at the same level.
Assessors: should look for efficiency in the use of the additional equipment provided via the
casualty and in the execution of the exercise.
118
TENSIONED ROPES FOR RESCUE

The use of a pair of tensioned ropes either horizontally or diagonally to keep a
casualty above the floor.
The ropes can be tensioned by using a 3:1 hauling system, using 1 person pulling
hand tight. This ensures forces on the anchors will remain within the SWL.
When connecting the casualty to the tensioned ropes two karabiners must be used
around both ropes, typically this is one short cowstails and a long cowstails. If the
casualty has to pass an intermediate anchor/ deviation, especially on horizontal tensioned ropes consideration should be given to having the casualty hanging from a
releasable point of attachment.
Due to the large angles involved in rigging horizontal tensioned ropes, Level 3 candidates should be aware of the forces involved on the ropes, anchors and other equipment, especially when subject to two person loading.
Candidate: Level 3 candidates shall demonstrate the use of tensioned ropes for rescue purposes.
Trainers: should ensure that during this manoeuvre candidates keep the casualty above the
ground during a horizontal or diagonal transfer, while using a pair of tensioned ropes. Anchors should
be equalised and the load shared between the two ropes.
Assessors: should note that tensioned ropes may be rigged as part of a planned evacuation
procedure, and this exercise may be assessed as part of the complex rescue.
TENSIONED ROPES FOR RESCUE
It is important that when the ropes a tensioned that both ropes are tensioned equally.
119
120
CLIMBING
RESCUES
121
RESCUE FROM AN AID CLIMB
RESCUE FROM AN AID CLIMB
Rescue of a casualty from an aid climb, suspended on either fixed or moveable anchors.
The rescuer will aid climb to the casualty and either rig a set of ropes and de
scend with the casualty or rig a lowering system and lower the casualty to the
ground.
In both cases the counter balance used in the ascent rescue will be used to
transfer the casualty onto the ropes rigged by the rescuer.

For the counter balance to be effective it must be fixed as high as possible
above the casualty.

Abseil Rescue
Using a spare rope, rig a set of ropes next to the casualty, try to keep the rig
ging as neat and small as possible.
Connect the casualties back-up device to the ropes.
Connect the casualties descender to their sterna (chest) D-ring.
Thread the descender onto the ropes and remove as much slack as possible.
Using a footloop through a high anchor point, use a counter balance to lift the
casualty from the aid climb.

Lower the casualty slowly onto their descender.
Make two attachments to the casualty.
Lowering Rescue
Using an additional rope, descender and back-up device rig a lowering system
next to the casualty.

Connect both ends of the rope to the casualties sternal attachment point and
remove as much slack as possible.


Lower the casualty slowly onto the lowering ropes.
Add extra friction to the descender.
Lower the casualty to the ground under control.
Candidates: Level 2 and 3 candidates shall demonstrate the rescue of a casualty who is suspended
by work-positioning lanyards such as cows tails.
Trainers: should note that the rescuer shall climb to the casualty with sufficient equipment,
including ropes (this may be a kit pre-rigged by the rescuer). The rescuer may either remain on the
structure and lower the casualty to safety, or rig ropes and descend with the casualty.
Assessors: should note that candidates need only demonstrate one climbing rescue during assessment, at the assessors discretion.
122
RESCUE FROM FALL ARREST EQUIPMENT
The rescuer will position themselves above the casualty and either rig a set of
ropes and descend with the casualty or rig a lowering system and lower the
casualty to the ground.
In both cases the counter balance used in the ascent rescue will be used to
transfer the casualty onto the ropes rigged by the rescuer.
For the counter balance to be effective it must be fixed as high as possible
above the casualty.
Abseil Rescue
Using a spare rope, rig a set of ropes next to the casualty, try to keep the rig
ging as neat and small as possible.
Connect the casualties back-up device to the ropes.
Connect the casualties descender to their sterna (chest) D-ring.
Thread the descender onto the ropes and remove as much slack as possible.

Lower the casualty slowly onto their descender.
Make two attachments to the casualty.
Lowering Rescue
Using an additional rope, descender and back-up device rig a lowering system
next to the casualty.

Connect both ends of the rope to the casualties sternal attachment point and
remove as much slack as possible.


Lower the casualty slowly onto the lowering ropes.
Add extra friction to the descender.
Lower the casualty to the ground under control.
Candidates: Level 2 and 3 candidates shall demonstrate the rescue of a casualty who is suspended
either by a fall arrest system (temporary or fixed) or by twin-tailed fall arrest lanyards.
Trainers: should note that the rescuer shall climb to the casualty with sufficient equipment, including
ropes (this may be a kit pre-rigged by the rescuer). The rescuer may either remain on the structure
and lower the casualty to safety, or rig ropes and descend with the casualty.
Assessors: should note that candidates need only demonstrate one climbing rescue during assessment, at the assessors discretion.
RESCUE FROM FALL ARREST EQUIPMENT
Rescue of a casualty who has fallen and if suspended on fall arrest lanyards.
123
SHORT LINK RESCUE

Rescue of a casualty who is suspended from a one connector link into a short strop
or a two connector link into a bolt anchor, in both cases no higher anchors are
available.
SHORT LINK RESCUE
The rescuer will aid climb into position next to the casualty, for this rescue it
may be necessary to share anchor points, always ensuring you and the casualty have a suitable back up.
When rigging ropes to attach the casualty to make sure the rigging is as small
and as neat as you can. If aid climb bolts are smooth then barrel knots may be
tied directly into them, if you must use additional karabiners knots must be as
small as possible i.e. Barrel knot.
Thread the casualties backup device and descender on to the ropes, remember the casualty must be in an upright position once on the ropes.
The rescue uses a footloop through the highest point, the bolt itself or karabiner, and using a counterbalance technique to lift the casualty off their anchor
point and onto the descent ropes.
The footloop attachment to the casualty must be as low down on the harness
as possible in order to maximise the distance available to lift the casualty.
This may be done by threading the footloop through the harness and the choking it back on its self.
Once the casualty is on the descent ropes the rescuer will then attach themselves to the casualty and descend under control to the ground.
Candidates: Level 3 candidates shall demonstrate the rescue of an unconscious casualty, i.e. Feigning immobility, from an aid climb, where the casualty is directly attached by a short connection and
where there are no higher anchors.
Trainers: should note that the casualty shall be directly attached to the anchor point with a
short connection. This shall normally be a two-connector attachment into a bolt anchor or a oneconnector attachment into a short wire-strop anchor. The rescuer shall not use any higher anchor
points.
Assessors: should take into account the difficulty in carrying out this type of rescue and
concentrate their assessment on safety aspects of the exercise.
124
COURSE NOTES
COURSE NOTES
125
COURSE NOTES
COURSE NOTES
126
COURSE NOTES
COURSE NOTES
127
Heightworks Ltd
Sidney Street,
Wolverhampton,
West Midlands,
WV2 4HH
UK.
www.heightworks.com
[email protected]

Heightworksiratatrainingmanualversion2 140911074418 Phpapp02 PDF

Uploaded by

Copyright:

Available Formats

Heightworksiratatrainingmanualversion2 140911074418 Phpapp02 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Heightworksiratatrainingmanualversion2 140911074418 Phpapp02 PDF

Uploaded by

Copyright:

Available Formats

Rope

I010 020914 Rev 2.0 IRATA Training Manual TACS Version

ABOUT THIS MANUAL

PLANNING AND MANAGEMENT

IRATA International system

ROPE ACCESS EQUIPMENT.

Selection, PPE, EN Standards and CE Marking.

I010 020914 Rev 2.0 IRATA Training Manual TACS Version

RIGGING FOR RESCUE AND HAULING

ROPE ACCESS MANOEUVRES

Rope to Rope Transfers

Horizontal Aid Climbing

Rescue from Aid Climb

I010 020914 Rev 2.0 IRATA Training Manual TACS Version

ABOUT THIS MANUAL

ABOUT THIS MANUAL

Information for all candidates

Information for Level 2

Information for Level 3

I010 020914 Rev 2.0 IRATA Training Manual TACS Version

PLANNING AND MANAGEMENT

I010 020914 Rev 2.0 IRATA Training Manual TACS Version

IRATA INTERNATIONAL SYSTEM

PLANNING AND MANAGEMENT

guidance for candidates, including pre-training requirements and topics covered;

requirements and guidance for IRATA International trainer member companies;

requirements and guidance for IRATA International instructors;

requirements and guidance for IRATA International assessors, including the

I010 020914 Rev 2.0 IRATA Training Manual TACS Version

Audited member companies and their operating procedures:

PLANNING AND MANAGEMENT

I010 020914 Rev 2.0 IRATA Training Manual TACS Version

PLANNING AND MANAGEMENT

I010 020914 Rev 2.0 IRATA Training Manual TACS Version

working at height if at all possible

the consequences of falls by utilising:Collective measures - Airbags/ Safety Nets

Collective measures always take precedence over personal measures.

PLANNING AND MANAGEMENT

I010 020914 Rev 2.0 IRATA Training Manual TACS Version

PLANNING AND MANAGEMENT

I010 020914 Rev 2.0 IRATA Training Manual TACS Version

Identify the hazards

PLANNING AND MANAGEMENT

I010 020914 Rev 2.0 IRATA Training Manual TACS Version

PLANNING AND MANAGEMENT

I010 020914 Rev 2.0 IRATA Training Manual TACS Version

EXCLUSION ZONES AND PROTECTION OF THIRD PARTIES

Protect anchor area

Exclusion zones may need to be set up above, below or

Set up protection for the anchor area. Consider protection of

All small tools and equipment will be attached to the harness

PLANNING AND MANAGEMENT

I010 020914 Rev 2.0 IRATA Training Manual TACS Version

PLANNING FOR EMERGENCIES AND FIRST AID

PLANNING AND MANAGEMENT

Elements of the rescue plan include:

Designated anchor points;

I010 020914 Rev 2.0 IRATA Training Manual TACS Version

Suspension intolerance is a condition in which