679 02 Fenner Chain Drives

CHAIN DRIVES
Section : 2
Section 2:
Chain Drives
Roller chain technology has evolved over the
centuries. During this time new design features and
production processes have been introduced. The new
Fenner roller chain products are a result of this
technology.
BS and ANSI transmission roller chains up to

1" simplex and 1" triplex
A comprehensive range of Fenner Taper

Lock sprockets, plus pilot bore sprockets and
platewheels
Stainless steel and 'lube-free' variants also

available
All Fenner chains can be supplied to specific
lengths
Chain Drives: Design Data Required
Chain Drives
Type of prime mover, or driving machine
Roller Chain Drive Selection
Electric motor starting arrangement
Roller Chain
Rotational speed of prime mover
Attachment Chain
13
Power rating of prime mover
Double Pitch Chain
14
Type of driven machine
Double Pitch Conveyor Chain
14
Rotational speed of driven machine
Special & Attachment Chain
15
Power absorbed by driven machine
Agricultural Chain
16
Hours/day duty & start/stop frequency
Leaf Chain
17
Both driven & driver machine shaft diameters
Page
3
7
Taper Lock Sprokets
20
Centre distance & space restraints:
> fixed centres?

> availability of lubrication?
Pilot Bore Sprockets
23
Platewheel Sprockets
27
Any environmental issues:

> ambient temperature

> noise limits
> water, oil mist, solvents etc.
Installation & Maintenance
30
Visit www.fptgroup.com
for the Drive Design Assistant
Accessories 32
Fenner Advanced Chain Technology
Fenner PLUS
Lubrication Free Chain
High Performance Chain
> Built-in lubrication

> Sintered bushes impregnated with oil
> Operating speed of up to 2.5m/sec
> Fit and forget reliability
> Easy Pin eXtraction feature
> Enhanced performance in hostile
environments
The Mark of Engineering Excellence
www.fptgroup.com
CHAIN DRIVES
Section : 2
Chain Drive Selection

SELECTION
(a) Service Factor
TABLE 1 SERVICE FACTORS
Types of Prime Mover

'Soft' Starts
From Table 1, determine the service factor which is

applicable to the drive.
(b) Design Power

Multiply the normal running power by the service factor.
This gives the Design Power which is used as the basis for
selecting the drive.
(c) Chain Pitch

Refer to Table 2 (page 4) and trace to the right along the
horizontal axis to the rev/min of the faster shaft. Trace
upwards along the vertical axis to the Design Power. At the
point of intersection, note the recommended chain pitch or
pitches if there is an overlap.
Electric motors:
A.C. Direct-on-line start
D.C. Series and compound
wound.
Internal combustion engines with
less than 4 cylinders.
Hours per day duty

Types of Driven Machine
(d) Speed Ratio
10 and
under
Over 10
to 16
Over 16
10 and
Under
Over 10
to 16
Over16
1.0
1.1
1.2
1.1
1.2
1.3
1.1
1.2
1.3
1.2
1.3
1.4
1.3
1.4
1.5
1.5
1.6
1.7
Light Duty
Divide the speed of the faster shaft by the speed of the

slower shaft to obtain the speed ratio.
Agitators (uniform density),

Belt conveyors (uniformly
loaded).
(e) Sprocket Sizes

Refer to Table 4 (page 6) and select driving and driven
sprockets to match the Speed Ratio found in step (d).
See sprocket pitch recommendations on page 4.
Medium Duty
Agitators and mixers (variable
density). Belt conveyors (not
uniformly loaded), Kilns,
Laundry machinery,
Lineshafts, Machine tools,
Printing machinery, Sawmill
and woodworking machinery,
Screens (rotary).
(f) Power Rating

Refer to the power rating tables (page 5) for the pitch of
chain chosen in step (c). Read down the left hand column
to the rotational speed of the faster shaft. On this line read
the power rating for the simplex chain selected. These
tables are for 19 tooth sprockets, if a sprocket with a
different number of teeth is used, the power rating should
be multiplied by the Sprocket Factor from the table at the
bottom of page 5.
If the power rating figure does not equal or preferably
exceed the Design Power, calculated in step (b), either
select a larger pitch or a multiple strand (duplex or triplex)
chain.
Single strand chain offers the most economical solution,
and should be used where possible. However, for
limitations in space, high speed or smooth running
requirements a smaller pitch, duplex or triplex drive may be
considered.
Heavy Duty
Brick machinery, Bucket
elevators, Conveyors (heavy
duty), Hoists, Quarry plant,
Rubber machinery, Screens
(vibrating), Textile machinery.
(g) Chain Length
EXAMPLE
To find the Chain length in pitches, use the formula below.

L = 2C + T + t + KP
P
2
C
L = Length of chain in pitches.
C = Centre distance in mm.
P =
Pitch of chain in mm.
T =
Number of teeth on large sprocket.
t = Number of teeth on small sprocket.
K = Factor from Table 3 (page 6).
The calculated number of pitches should be rounded up to
an even, whole number of pitches. If the centre distance
cannot be adjusted, to allow for the use of an even number
of pitches, it may be necessary to use an offset or cranked
link, in which case the chain power rating will need to
be reduced, consult your local Authorised Distributor.
Re-calculate the exact centre distance required for the
adjusted number of pitches. For recommended centre
distance, refer to Table 5 below.
If a jockey or tensioning sprocket is used, add an extra 2
pitches.
To obtain the chain length, multiply the number of pitches
by the pitch of the chain.
Length of chain in feet =

'Heavy' Starts
Electric motors:
A.C. Star-delta start
D.C. Shunt wound
Internal combustion engines with 4
or more cylinders. All prime movers
fitted with centrifugal clutches, dry
or fluid couplings.
Select a chain drive to transmit 1.5 kW from a gearbox

running at 80 rev/min and driven by a direct-on-line
electric motor, to a uniformly loaded conveyor drive shaft
which is required to run at approximately 40 rev/min for
12 hours per day. Gearbox output shaft is 35mm and the
conveyor headshaft is 65mm diameter.
(a) Service Factor
g) Chain Length
From Table 1 the Service Factor is 1.2.
Recommended centre distance for 16B-1 chain is 1000

mm (Table 5 below).
Therefore the chain length as per selection step (g)
(chain length) is 108 pitches including a connecting link.
(b) Design Power

= 1.5 x 1.2 = 1.8 kW.
(c) Chain Pitch

By referring to Table 2 (page 4), the intersection of design
power and the rev/min of the faster shaft indicates a 16B
1 pitch chain.
Drive Specification
From Table 4 (page 6) sprockets of 19 and 38 teeth give

a ratio of 2 : 1.
108 pitches or 9 feet of Fenner 16B-1 chain

81-19 Driver Sprocket with a 2517 x 35mm bore
81-38 Driven Sprocket with a 3020 x 65mm bore
Alternative selection
Recommended centre distance for 12B-2 chain is 900 mm
(Table 5 below).
Therefore the chain length as per selection step (g) (chain
length) is 124 pitches including a connecting link.
(f) Power Rating
Alternative Drive Specification
(d) Speed Ratio

80

40 = 2:1
(e) Sprocket Size
LP
305
sprocket, running at 80 rev/minute, the power rating for 16B1 simplex chain is 3.79 kW. As this exceeds the required
design power the selection is satisfactory.
If space limitations demand smaller sprocket dimensions,
alternative selections would be: use 12B-2 duplex chain
which has a power rating of 2.11 kW at 80 rev/min or 15 T
driving to 30 T on 16 B-1 1" simplex chain - power rating 0.8
x 3.79 = 3.03 kW
The power ratings for 16B chain are given on page 5. The
required power rating from step (b) is 1.8 kW. For a 19T driver
124 pitches or 7.75 feet of Fenner 12B-2 chain

62-19 Driver Sprocket with a 2012 x 35mm bore
62-38 Driven Sprocket with a 3020 x 65mm bore.
TABLE 5 - RECOMMENDED CENTRE DISTANCE

Chain Pitch
Centre Distance
Inches
3/8"
1/2"
5/8"
3/4"
1"
1.1/4"
1.1/2"
1.3/4"
2"
mm
9.525
12.7
15.875
19.05
25.4
31.75
38.1
44.45
50.8
mm
450
600
750
900
1000
1200
1350
1500
1700
FEN01/14 : Drive Design & Maintenance Manual
Section : 2
chan drives

TABLE 2 - RECOMMENDED CENTRE DISTANCE
200
100
LARGER SIZES ARE

AVAILABLE CONSULT YOUR LOCAL
AUTHORISED DISTRIBUTOR
80
60
50
40
30
20
10
2B
DESIGN POWER kW
8
6
5
2"
8
0.
(5
B
28
4.
4
"(
1.
4B
38
1.
20
5m
.7
31
"(
1.
B
16
m
.1
"(
5m
25
(
1"
B
12
4m
"
m
(19
B
10
0.8
"
5 /8
B
08
0.6
0.5
87
.
(15
.
12
0.4
06
0.3
7m
"(
9.
"(
3 /8
5m
0.2
4000
3000
800
600
1000
2000
Rev/min of FASTER SHAFT
500
400
300
100
200
80
60
50
40
30
10
20
0.1
GENERAL RECOMMENDATIONS ON SPROCKET SIZES

19 teeth and above
Sprockets running at medium to maximum speeds on normal applications (see power
ratings for speeds on page 5).
17 teeth
Permissible to use this sprocket on very small pitches ie, 8mm and 3/8". Refer to section
above, but should be restricted to slow speed drives (see power ratings for speeds on
page 5).
15 teeth or less
Should be avoided unless shaft speed is below 100 revs/min.
23 teeth and above

Recommended for impulse applications.
When ratios are low, the use of sprockets with high numbers of teeth minimises joint
articulation, chain pull and bearing loads. If a small number of teeth are used on high
speed, high load applications, hardening of teeth should be considered. Ratios

over 7:1 are not recommended for single strand drives. In all drives where
ratios exceed 5:1 the designer should consider using compound drives for
maximum service life.
On drives where ratios exceed 3:1 the shaft centre distance should not be less
than the sum of the sprocket pitch circle diameters.
For drives with vertical shafting always use multi-strand chains.
chain drives
Section : 2

POWER RATINGS (KW) FOR BRITISH STANDARD CLASSIC CHAIN BASED ON 19 TOOTH DRIVER SYSTEM
06B
Rev/min
faster
shaft
20
40
60
80
100
200
400
600
800
1000
1200
1400
1600
1800
2000
2200
2400
2600
2800
3000
/8" (9.5mm) PITCH
19 Tooth
Duplex
Triplex
0.06
0.11
0.16
0.20
0.25
0.46
0.86
1.24
1.60
1.96
2.31
0.10
0.19
0.27
0.34
0.43
0.78
1.46
2.11
2.72
3.33
3.93
0.15
0.27
0.40
0.50
0.62
1.15
2.15
3.10
4.00
4.90
5.77
2.65
2.99
3.33
3.66
3.99
4.31
4.63
4.95
5.27
4.51
5.10
5.66
6.22
6.78
7.33
7.87
8.42
8.96
6.62
7.47
8.32
9.15
9.97
10.77
11.57
12.37
13.17
Rev/min
faster
shaft
10
20
30
40
50
60
70
80
90
100
200
300
400
500
600
700
800
900
1000
1200
10
25
50
100
150
200
300
400
500
600
700
500
600
800
900
1200
1400
1600
1800
Duplex
Triplex
0.19
0.36
0.51
0.66
0.84
0.96
1.10
1.24
1.38
1.55
2.90
0.32
0.61
0.87
1.12
1.43
1.63
1.87
2.11
2.35
2.64
4.93
0.48
0.90
1.28
1.65
2.10
2.40
2.75
3.10
3.45
3.88
7.25
4.07
5.27
6.62
7.60
8.95
9.84
11.26
12.03
14.55
6.92
8.96
11.25
12.92
15.22
16.73
19.14
20.45
25.74
10.18
13.18
16.55
19.00
22.38
24.60
28.5
35.08
36.38
300
400
500
600
700
800
900
1000
Duplex
Triplex
2.22
5.03
9.40
17.50
25.30
32.70
47.20
61.60
74.60
88.00
94.00
3.77
8.55
15.98
29.75
43.01
55.59
80.24
104.72
126.82
149.60
159.80
5.55
12.58
23.50
43.75
63.25
81.75
118.00
154.00
186.50
220.00
235.00
0.07
0.14
0.20
0.26
0.31
0.37
0.42
0.48
0.58
1.09
1.57
0.12
0.24
0.34
0.44
0.53
0.63
0.71
0.82
0.99
1.85
2.67
0.17
0.35
0.50
0.65
0.77
0.92
1.05
1.20
1.45
2.72
3.92
2.03
2.48
2.92
3.78
4.63
5.45
6.26
7.06
7.85
3.45
4.22
4.96
6.43
7.87
7.27
10.64
12.00
13.35
5.07
6.20
7.30
9.45
11.57
13.62
15.65
17.65
19.62
Duplex
Triplex
0.31
0.58
1.09
1.57
2.03
2.48
2.92
3.36
3.79
4.21
4.63
0.53
0.99
1.85
2.67
3.45
4.22
4.96
5.71
6.44
7.16
7.87
0.78
1.45
2.73
3.93
5.08
6.20
7.30
8.40
9.48
10.53
11.58
8.64
12.45
16.13
19.72
23.23
26.69
30.10
33.46
36.79
14.69
21.17
27.42
33.52
39.49
45.37
51.17
56.88
62.54
21.60
31.13
40.33
49.30
58.08
66.73
75.25
83.65
91.98
19 Tooth
10
25
50
100
150
200
250
300
350
400
450
500
600
Lubrication
Type of
Simplex
Duplex
Triplex
3.44
7.83
14.32
27.30
39.39
51.10
62.66
73.18
84.30
94.70
105.90
116.40
133.50
5.85
13.31
24.34
46.41
66.96
86.87
106.52
124.41
143.31
160.99
180.03
197.88
226.95
8.60
19.58
35.80
68.25
98.48
127.75
156.65
182.95
210.75
236.75
264.75
291.00
333.75
/ " (15.875 mm) PITCH
10B
Rev/min
faster
shaft
58
19 Tooth
Type of
Simplex
Duplex
Triplex
10
20
30
40
50
60
70
80
100
200
300
400
0.13
0.25
0.36
0.46
0.57
0.67
0.76
0.86
1.07
1.96
2.88
0.22
0.43
0.61
0.78
0.96
1.13
1.29
1.47
1.78
3.33
4.80
0.33
0.63
0.89
1.15
1.40
1.66
1.90
2.15
2.62
4.90
7.05
3.65
6.21
9.13
500
600
800
900
1000
1200
1500
4.55
5.25
6.81
7.76
8.33
9.81
12.01
7.80
8.94
11.58
13.19
14.16
16.68
20.42
1.17
13.15
17.03
19.40
23.33
24.42
29.90
20B
Rev/min
faster
shaft
10
25
50
100
150
200
250
300
350
400
450
500
600
700
800
Lubrication
1." (31.75mm) PITCH

19 Tooth
Type of
Simplex
Duplex
Triplex
1.02
2.50
4.65
8.65
12.40
16.20
19.73
23.27
26.70
30.20
33.50
1.73
4.25
7.90
14.70
21.08
27.54
33.54
39.56
45.40
51.34
56.95
2.55
6.25
11.63
21.63
31.00
40.50
49.33
58.18
66.75
75.50
83.75
36.92
43.50
49.95
55.50
62.76
73.95
84.91
94.35
92.30
108.75
124.88
138.75
Lubrication
1." (44.45mm) PITCH
Rev/min
faster
shaft
Lubrication
Lubrication
Type of
Simplex
28B
Type of
Simplex
Triplex
19 Tooth
5
10
20
30
40
50
60
70
80
90
100
200
1." (38.1mm) PITCH
Duplex
1" (25.4mm) PITCH
Rev/min
faster
shaft
Lubrication
19 Tooth
Type of
Simplex
16B
Type of
Simplex
19 Tooth
10
20
30
40
50
60
70
80
100
200
300
400
" (19mm) PITCH
24B
Rev/min
faster
shaft
Lubrication
19 Tooth
" (12.7mm) PITCH
Rev/min
faster
shaft
Type of
Simplex
12B
08B
Lubrication
1
32B
Rev/min
faster
shaft
10
25
50
100
150
200
250
300
350
400
500
2" (50.8mm) PITCH

19 Tooth
Type of
Simplex
Duplex
Triplex
4.54
10.44
19.40
36.10
51.80
67.30
82.10
97.00
112.00
126.00
154.00
7.72
17.75
32.98
61.37
88.06
114.41
139.57
164.90
190.40
214.20
261.80
11.35
26.10
48.50
90.25
129.50
168.25
205.25
242.50
280.00
315.00
385.00
Lubrication
1
Sprocket Factor
No of Teeth
Factor
11
0.5
13
0.65
15
0.8
17
0.9
19
1.0
21
1.1
23
1.2
25
1.3
27
1.4
For detail of lubrication types see page 30
For driver sprockets other than 19 tooth, multiply the power rating by the Sprocket Factor (above) to calculate the actual power rating.
Section : 2
chain drives

TABLE 3 K FACTOR
T-t
T-t
T-t
T-t
T-t
T-t
T-t
T-t
T-t
11
21
11
31
24
41
43
51
66
61
94
71
128
81
166
12
22
12
32
26
42
45
52
68
62
97
72
131
82
170
13
23
13
33
28
43
47
53
71
63
101
73
135
83
175
14
24
15
34
29
44
49
54
74
64
104
74
139
84
179
15
25
16
35
45
51
55
77
65
107
75
142
85
183
16
26
17
36
33
46
54
56
79
66
110
76
146
86
187
17
27
18
37
35
47
56
57
82
67
114
77
150
87
192
18
28
20
38
37
48
58
58
85
68
117
78
154
88
196
19
29
21
39
39
49
61
59
88
69
121
79
158
89
201
10
20
10
30
23
40
41
50
63
60
91
70
124
80
162
90
205
TABLE 4 SPEED RATIOS

Number of Teeth - Driving Sprocket
Number of Teeth - Driving Sprocket
10
11
12
13
14
15
16
17
18
19
20
23
24
25
27
30
11
1.10
1.00
12
1.20
1.09
1.00
13
1.30
1.18
1.08
1.00
14
1.40
1.27
1.17
1.08
1.00
15
1.50
1.36
1.25
1.15
1.07
1.00
16
1.60
1.45
1.33
1.23
1.14
1.07
1.00
17
1.70
1.55
1.42
1.31
1.21
1.13
1.06
1.00
18
1.80
1.64
1.50
1.38
1.29
1.20
1.13
1.06
1.00
19
1.90
1.73
1.58
1.46
1.36
1.27
1.19
1.12
1.06
1.00
20
2.00
1.82
1.67
1.54
1.43
1.33
1.25
1.18
1.11
1.05
1.00
21
2.10
1.91
1.75
1.62
1.50
1.40
1.31
1.24
1.17
1.11
1.05
1.00
22
2.20
2.00
1.83
1.69
1.57
1.47
1.38
1.29
1.22
1.16
1.10
1.05
1.00
23
2.30
2.09
1.92
1.77
1.64
1.53
1.44
1.35
1.28
1.21
1.15
1.10
1.05
1.00
24
2.40
2.18
2.00
1.85
1.71
1.60
1.50
1.41
1.33
1.26
1.20
1.14
1.09
1.04
1.00
25
2.50
2.27
2.08
1.92
1.79
1.67
1.56
1.47
1.39
1.32
1.25
1.19
1.14
1.09
1.04
1.00
26
2.60
2.36
2.17
2.00
1.86
1.73
1.63
1.53
1.44
1.37
1.30
1.24
1.18
1.13
1.08
1.04
27
2.70
2.45
2.25
2.08
1.93
1.80
1.69
1.59
1.50
1.42
1.35
1.29
1.23
1.17
1.13
1.08
1.00
28
2.80
2.54
2.33
2.15
2.00
1.87
1.75
1.65
1.56
1.47
1.40
1.33
1.27
1.22
1.17
1.12
1.04
29
2.90
2.64
2.42
2.23
2.07
1.93
1.81
1.71
1.61
1.53
1.45
1.38
1.32
1.26
1.21
1.16
1.07
30
3.00
2.73
2.50
2.31
2.14
2.00
1.88
1.76
1.67
1.58
1.50
1.43
1.36
1.30
1.25
1.20
1.11
1.00
38
3.80
3.45
3.17
2.92
2.71
2.53
2.38
2.24
2.11
2.00
1.90
1.81
1.73
1.65
1.58
1.52
1.41
1.27
57
5.70
5.18
4.75
4.38
4.07
3.80
3.56
3.35
3.17
3.00
2.85
2.71
2.59
2.48
2.38
2.28
2.11
1.90
76
7.60
6.91
6.33
5.85
5.43
5.07
4.75
4.47
4.22
4.00
3.80
3.62
3.45
3.30
3.17
3.04
2.81
2.53
95
9.50
8.64
7.92
7.31
6.79
6.33
5.94
5.59
5.28
5.00
4.75
4.52
4.32
4.13
3.96
3.80
3.52
3.17
CHAIN LENGTH CONVERSION DATA

Chain Pitch (ins)
6mm
8mm
"
/"
38
"
/"
3/4"
22
1.00
Ratios in bold type can generally be achieved using Fenner Taper Lock sprockets.
5 8
21
10
Pitches (ft)
Pitches/Metre
Chain Pitch (ins)
Pitches/Ft
Pitches/metre
50.8
38.1
48
32
24
19.2
16
166.67
125.00
157.48
104.99
78.74
62.99
52.49
1"
12
9.6
8
6.86
6
39.37
31.49
26.25
22.50
19.68
1"
1"
1"
2"
chain drives
Section : 2
Roller Chain
Roller Chain Links
Conn Link
Conn Link
Rivet Pin Link
Spring Clip Type
Cotter Type
Rivet-on Type
Double Offset Link
Inner Link
Offset Link
SPRING CLIP CONNECTING LINK
BRITISH STANDARD (BS)

04B
04B
04B
04B
05B
05B
05B
05B
06B
06B
06B
06B
06B
06B
08B
10B
08B
10B
08B
10B
08B
10B
08B
10B
08B
10B
12B
12B
12B
12B
12B
12B
16B
16B
16B
16B
16B
16B
20B
24B
28B
32B
20B
24B
28B
32B
COTTER CONNECTING LINK
20B
24B
28B
32B
AMERICAN STANDARD (ASA)

25
35
40
41
50
60
80
35
40
41
50
60
80
100
120
140
160
25
35
40
41
50
60
80
100
120
140
160
25
35
40
41
50
60
80
25
35
40
41
50
60
80
100
120
140
180
35
40
41
50
60
80
100
120
140
180
50H
60H
80H
100H
120H
40H
50H
60H
80H
100H
120H
40H
50H
60H
80H
100H
120H
40H
50H
60H
80H
100H
120H
50H
60H
80H
100H
120H
A2040
A2050
A2060
C2040
C2050
C2060/H
C2080/H
C2100/H
C2120/H
C2042
A2040
A2050
A2060
C2040
C2050
C2060/H
C2080/H
C2100/H
C2120/H
C2042
A2040
A2050
A2060
C2040
C2050
C2060/H
C2042
A2040
A2050
A2060
C2040
C2050
C2060/H
C2080/H
C2100/H
C2120/H
C2042
C2052
C2052
C2052
C2052
C2052
C2062/H
C2062/H
C2082/H
C2102/H
C2102/H
C2122/H
C2062/H
C2082/H
C2102/H
C2102/H
C2122/H
C2062/H
C2082/H
C2102/H
C2102/H
C2122/H
C2062/H
RIVET PIN LINK
ASA HEAVY DUTY

40H
50H
60H
80H
INNER LINK
DOUBLE PITCH
A2040
A2050
A2060
C2040
C2050
C2060/H
C2042
ENDLESS - EVEN NO. OF LINKS
ENDLESS - odd NO. OF LINKS
Odd number of links, with inner at each end and 1

standard connecting link.
Even number of links, with inner at one end and outer at

other end plus 1 offset link.
OFFSET LINK
DOUBLE OFFSET LINK
ENDLESS - ODD NO. OF LINKS
Odd number of links, with outer at each end plus 1 double

offset link.
Section : 2
chain drives
British Standard Roller Chains

BS 228, ISO R606, DIN 8187
Pt
Product Code
Fenner PLUS
ISO Chain
No
Pt
ISO Pitch
Roller
Diameter
Width
Between
Inner Plates
Pin
Diameter
P
(mm)
d1 max
(mm)
b1 min
(mm)
d2 max
(mm)
L max
(mm)
Lc max
(mm)
Pin Length
Pt
Inner Plate
Depth
Plate
Thickness
Transverse
Pitch
Fenner
PLUS Min
Tensile
Strength
Weight per
foot
h2 max
(mm)
T/t max
(mm)
Pt
(mm)
Q min
kN
q
kg/m
SIMPLEX
028A0111
#06B-1
9.525
6.35
5.72
3.27
13.50
14.10
8.23
1.30
9.00
0.122
028B0111
08B-1
12.700
8.51
7.75
4.45
16.60
18.20
11.80
1.60
18.20
0.210
028C0111
10B-1
15.875
10.16
9.65
5.08
19.00
20.90
13.70
1.70
23.00
0.259
028D0111
12B-1
19.050
12.07
11.68
5.72
22.30
24.20
16.20
1.85
30.50
0.357
028E0111
16B-1
25.400
15.88
17.02
8.28
35.10
37.40
20.80
4.15/3.10
66.00
0.811
028F0111
20B-1
31.750
19.05
19.56
10.19
40.50
45.00
25.40
4.5/3.5
105.00
1.134
028G0111
24B-1
38.100
25.40
25.40
14.63
53.10
57.80
32.30
6.0/4.8
180.00
2.149
028T0111
28B-1
44.450
27.94
30.95
15.9
65.10
69.50
37.00
7.5/6.0
235.00
2.731
028U0111
32B-1
50.800
29.21
30.99
17.81
63.60
71.00
42.30
7.0/6.0
270.00
3.048
028V0111
40B-1
63.500
39.37
38.10
22.89
79.00
89.20
52.80
8.5/8.0
365.00
4.938
028Z0111
48B-1
76.200
48.26
45.72
29.24
99.10
107.00
64.20
12/10
600.00
7.598
DUPLEX
028A0211
#06B-2
9.525
6.35
5.72
3.27
23.80
24.40
8.23
1.30
10.24
17.60
0.226
028B0211
08B-2
12.700
8.51
7.75
4.45
30.60
32.20
11.80
1.60
13.92
36.40
0.411
028C0211
10B-2
15.875
10.16
9.65
5.08
35.75
37.50
13.70
1.70
16.59
46.00
0.506
028D0211
12B-2
19.050
12.07
11.68
5.72
41.80
43.60
16.20
1.85
19.46
61.00
0.707
028E0211
16B-2
25.400
15.88
17.02
8.28
68.00
69.30
20.80
4.15/3.10
31.88
132.00
1.609
028F0211
20B-2
31.750
19.05
19.56
10.19
77.00
81.50
25.40
4.5/3.5
36.45
210.00
2.243
028G0211
24B-2
38.100
25.40
25.40
14.63
101.80
106.20
33.40
6.0/4.8
48.36
360.00
4.221
028T0211
28B-2
44.450
27.94
30.95
15.9
124.60
129.10
37.00
7.5/6.0
59.56
470.00
5.73
028U0211
32B-2
50.800
29.21
30.99
17.81
124.60
129.60
42.30
7.0/6.0
58.55
540.00
6.035
028V0211
40B-2
63.500
39.37
38.10
22.89
152.00
161.50
52.80
8.5/8.0
72.29
730.00
9.778
028Z0211
48B-2
76.200
48.26
47.70
29.22
190.40
198.20
64.20
12/10
91.21
1200.00
15.087
TRIPLEX
028A0311
#06B-3
9.525
6.35
5.72
3.27
34.00
34.60
8.23
1.30
10.24
26.50
0.335
028B0311
08B-3
12.700
8.51
7.75
4.45
44.60
46.10
11.80
1.60
13.92
54.60
0.616
028C0311
10B-3
15.875
10.16
9.65
5.08
52.30
54.10
13.70
1.70
16.59
69.00
0.795
028D0311
12B-3
19.050
12.07
11.68
5.72
61.40
63.10
16.20
1.85
19.46
91.50
1.975
028E0311
16B-3
25.400
15.88
17.02
8.28
99.90
101.20
20.80
4.15/3.1
31.88
198.00
2.396
028F0311
20B-3
31.750
19.05
19.56
10.19
113.50
117.90
25.40
4.5/3.5
36.45
315.00
3.353
028G0311
24B-3
38.100
25.40
25.40
14.63
150.20
154.60
33.40
6.0/4.8
48.36
540.00
6.190
028T0311
28B-3
44.450
27.94
30.95
15.9
184.60
188.70
37.00
7.5/6.0
59.56
705.00
8.534
028U0311
32B-3
50.800
29.21
30.99
17.81
184.60
188.20
42.30
7.0/6.0
58.55
810.00
9.022
028V0311
40B-3
63.500
39.37
38.10
22.89
224.60
233.80
52.80
8.5/8.0
72.29
1095.00
14.617
028Z0311
48B-3
76.200
48.26
47.70
29.22
281.60
289.40
64.20
12/10
# Straight side plates.
All Fenner PLUS chains are equivalent to or exceed ISO 606 minimum tensile strength. The above dimensions are for Fenner PLUS chain, some non-functional
dimensions may differ slightly for Fenner Standard chain
8
91.21
1800.00
24.444
Chain is sold in units of feet or metres,
depending on geographical market
For weight in metres multiply by 3.281
chain drives
Section : 2
American Standard Roller Chains

ANSI B29.1, ISO R606, DIN 8188
ANSI standard chain is dimensionally similar

to BS chain but with generally thicker plates
resulting in a narrower b1 dimension between
inner plates.
The pitching between strands of duplex and
triplex chain, dimension Pt may also vary
from BS chain.
Care should be taken to ensure that correct
sprockets are used with ANSI chain.
Pt
Product Code
ANSI
Chain
No
ISO Chain
No
ISO Pitch
Roller
Diameter
Width
Between
Inner
Plates
Pin
Diameter
P (mm)
d1 ma
(mm)
b1 min
(mm)
d2 max
(mm)
L max
(mm)
Pt
Inner Plate
Depth
Plate
Thickness
Transverse
Pitch
Lc max
(mm)
h2 max
(mm)
t/T max
(mm)
Pt (mm)
Pin Length
Pt
Fenner
PLUS Min
Tensile
Strength
Weight per
foot
q
kg/m
SIMPLEX
028L0111
40
08A-1
12.700
7.930
7.85
3.98
16.30
17.80
11.50
1.50
16.50
0.18
028N0111
50
10A-1
15.875
10.150
9.55
5.09
20.45
22.20
13.70
2.03
27.00
0.304
028P0111
60
12A-1
19.050
11.910
12.65
5.96
25.40
27.70
16.20
2.42
38.00
0.414
028Q0111
80
16A-1
25.400
15.880
15.88
7.94
32.80
35.00
20.80
3.25
62.00
0.786
028R0111
100
20A-1
31.750
19.050
19.05
9.53
39.60
44.70
25.40
4.00
99.00
1.183
028S0111
120
24A-1
38.100
22.220
25.40
11.10
49.60
54.30
35.20
4.80
140.00
1.695
028W0111
140
28A-1
44.450
25.400
25.40
12.70
53.50
59.00
42.00
5.60
178.00
2.268
028X0111
160
32A-1
50.800
28.580
31.75
14.27
64.00
69.60
48.20
6.40
228.00
3.06
028Y0111
200
40A-1
63.500
39.670
38.10
19.85
77.90
87.20
58.00
8.00
380.00
5.09
028Z0111
240
48A-1
76.200
47.630
47.60
23.80
94.50
103.00
71.80
9.50
700.00
7.22
DUPLEX
028L0211
40-2
08A-2
12.700
7.930
7.85
3.98
30.80
32.2
11.50
1.50
14.38
33.00
0.366
028N0211
50-2
10A-2
15.875
10.150
9.55
5.09
38.90
40.4
13.70
2.03
18.11
54.00
0.609
028P0211
60-2
12A-2
19.050
11.910
12.65
5.96
48.30
50.5
16.20
2.42
22.78
76.00
0.829
028Q0211
80-2
16A-2
25.400
15.880
15.87
7.94
62.30
64.3
20.80
3.25
29.29
124.00
1.554
028R0211
100-2
20A-2
31.750
19.050
19.05
9.53
75.50
80.5
25.40
4.00
35.76
198.00
2.347
028S0211
120-2
24A-2
38.100
22.220
25.40
11.10
95.30
99.7
35.20
4.80
45.44
280.00
3.340
028W0211
140-2
28A-2
44.450
25.400
25.40
12.70
102.60
107.9
42.00
5.60
48.87
356.00
4.499
028X0211
160-2
32A-2
50.800
28.580
31.75
14.27
123.30
144.4
48.20
6.40
58.55
456.00
6.065
028Y0211
200-2
40A-2
63.500
39.670
38.10
19.85
150.20
158.8
58.00
8.00
71.55
760.00
10.119
028Z0211
240-2
48A-2
76.200
47.600
47.60
23.80
182.20
190.8
71.80
9.50
87.83
1400.00
14.400
TRIPLEX
028L0311
40-3
08A-3
12.700
7.930
7.85
3.98
45.30
46.6
11.50
1.50
14.38
49.50
0.550
028N0311
50-3
10A-3
15.875
10.150
9.55
5.09
57.00
58.5
13.70
2.03
18.11
81.00
0.908
028P3011
60-3
12A-3
19.050
11.910
12.65
5.96
71.10
73.3
16.20
2.42
22.78
114.00
1.243
028Q3011
80-3
16A-3
25.400
15.880
15.88
7.94
91.80
93.6
20.80
3.25
29.29
186.00
2.340
028R3011
100-3
20A-3
31.750
19.050
19.05
9.53
112.10
116.3
25.40
4.00
35.76
297.00
3.511
028S0311
120-3
24A-3
38.100
22.220
25.40
11.10
140.90
145.2
35.20
4.80
45.44
420.00
5.011
028W0311
140-3
28A-3
44.450
25.400
25.40
12.70
152.40
156.8
42.00
5.60
48.87
534.00
6.730
028X0311
160-3
32A-3
50.800
28.580
31.75
14.27
182.00
182
48.20
6.40
58.55
684.00
9.070
028Y0310
200-3
40A-3
63.500
39.670
38.10
19.85
222.20
230.4
58.00
8.00
71.55
1140.00
15.148
028Z0311
240-3
48A-3
76.200
47.600
47.60
23.80
270.00
278.6
71.80
9.50
87.83
2100.00
21.490
Cottered chain can be supplied for all chains of 19.05 mm pitch and above.
All Fenner PLUS chains are equivalent to or exceed ISO 606 minimum tensile strength. The above dimensions are for Fenner PLUS chain, some non-functional
dimensions may differ slightly for Fenner Standard chain
Chain is sold in units of feet or metres,

depending on geographical market
For weight in metres multiply by 3.281
Section : 2
chain drives
British Standard Fenner PLUS Lubrication Free Roller Chain

BS 228, ISO R606, DIN 8187
Pt
Pt
Product Code
ISO Chain
No.
Pitch
Roller
Diameter
P
(mm)
d1 max
(mm)
Width
Beteen Inner Pin Diameter
Plates
b1 min
(mm)
d2 max
(mm)
Pin Length
L max
(mm)
Lc max
(mm)
Inner Plate
Depth
Plate
Thickness
h2 max
(mm)
t/T max
(mm)
Pt
Fenner PLUS
Transverse
Weight per
Min Tensile
Pitch
Foot
Strength
Pt
(mm)
Q min
(kN)
q
kg/m
SIMPLEX
028B0114
08B-1
12.700
8.51
7.75
4.45
16.60
18.20
11.80
1.6
17.80
0.210
028C0114
10B-1
15.875
10.16
9.65
5.08
19.00
20.90
13.70
1.7
22.20
0.259
028D0114
12B-1
19.050
12.07
11.68
5.72
22.30
24.20
16.20
1.85
28.90
0.357
028E0114
16B-1
25.400
15.88
17.02
8.28
35.10
37.40
20.80
4.15/3.1
60.00
0.811
DUPLEX
028B0214
08B-2
12.700
8.51
7.75
4.45
30.60
32.20
11.80
1.6
13.92
31.10
0.411
028C0214
10B-2
15.875
10.16
9.65
5.08
35.75
37.50
13.70
1.7
16.59
44.50
0.506
028D0214
12B-2
19.050
12.07
11.68
5.72
41.80
43.60
16.20
1.85
19.46
57.80
0.707
028E0214
16B-2
25.400
15.88
17.02
8.28
68.00
69.30
20.80
4.15/3.1
31.88
106.00
1.609
TRIPLEX
028B0314
08B-3
12.700
8.51
7.75
4.45
44.60
46.10
11.80
1.6
13.92
44.50
0.616
028C0314
10B-3
15.875
10.16
9.65
5.08
52.30
54.10
13.70
1.7
16.59
66.70
0.795
028D0314
12B-3
19.050
12.07
11.68
5.72
61.40
63.10
16.20
1.85
19.46
86.70
1.975
028E0314
16B-3
25.400
15.88
17.02
8.28
99.90
101.20
20.80
4.15/3.1
31.88
160.00
2.396
Chain is sold in units of feet or metres, depending on geographical market
10
Section : 2
Pt
chain drives
American Standard Roller Chains

AMERICAN STANDARD ROLLER CHAINS
"H" SERIES ROLLER CHAINS
Pt
Pt
ANSI H Series chains are dimensionally identical to ANSI standard chains

except that the sideplates are thicker. The heavier side plates provide some
additional fatigue resistance. They are primarily intended for applications
where occasional shock loads are likely to cause fatigue failures in the
chain. Whilst there is an increase in tensile strength, the wear life of the
case hardened pins remains the same as for standard chain.
Pt
Simplex H series chains operate on standard ANSI sprockets. Multiple

strand H chain require non-standard ANSI sprockets because of the
thicker side plates.
Roller
Diameter
Width
Between
Inner Plates
Pin
Diameter
P
(mm)
d1 max
(mm)
b1 min
(mm)
d2 max
(mm)
Pt
Product Code
ANSI Chain
No
Pitch
Pin Length
L max
(mm)
LC max
(mm)
Inner Plate
Depth
Plate
Thickness
Minimum
Tensile
Strength
Average
Tensile
Strength
Weight per
Metre
h2 max
(mm)
t/T max
(mm)
Q min
(kN)
Q0
(kN)
q
kg/m
40H
12.700
7.95
7.85
3.96
18.80
19.90
12.00
2.03
14.10
19.10
0.82
50H
15.875
10.16
9.40
5.08
22.10
23.40
15.09
2.42
22.20
30.20
1.25
Pt
028L5114
028N0114
028P0114
60H
19.050
11.91
12.57
5.94
29.20
31.00
18.00
3.25
31.80
42.70
1.87
028Q0114
80H
25.400
15.88
15.75
7.92
36.20
37.70
24.00
4.00
56.70
71.40
3.10
028R0114
100H
31.750
19.05
18.90
9.53
43.60
46.90
30.00
4.80
88.50
112.40
4.52
028S0114
120H
38.100
22.23
25.22
11.10
53.50
57.50
35.70
5.60
127.00
160.90
6.60
028W0114
140H
44.450
25.40
25.22
12.70
57.60
62.20
41.00
6.40
172.40
217.30
8.30
028X0114
160H
50.800
28.58
31.55
14.27
68.20
73.00
47.80
7.20
226.80
285.80
10.30
028Z0114
200H
63.500
39.68
37.85
19.85
86.60
93.50
60.00
9.50
353.80
444.50
19.16
Note; Refer to your local Autorised Distributor for dimensional details of ANSI "H" Series multiple strand chain
"SH" SERIES ROLLER CHAINS

ANSI SH series chains are identical to H series but they have a
different pin material, which is through hardened. The surface hardness
is less than that of the carburised pins in the ANSI standard and ANSI
H series chains but through hardened pins provide additional fatigue
resistance, at some slight sacrifice in wear life.
Simplex SH series chains operate on standard ANSI sprockets.
Multiple strand SH series chain requires non-standard ANSI sprockets
because of the thicker side plates.
Product Code
ANSI Chain
No
Pitch
Roller
Diameter
Width
Between
Inner Plates
Pin
Diameter
P
(mm)
d1 max
(mm)
b1 min
(mm)
d2 max
(mm)
Pin Length
L max
(mm)
LC max
(mm)
Inner Plate
Depth
Plate
Thickness
Minimum
Tensile
Strength
Average
Tensile
Strength
Weight per
Metre
h2 max
(mm)
T max
(mm)
Q min
(kN)
Q0
(kN)
q
kg/m
028L5115
40SH
12.700
7.95
7.85
3.96
18.80
19.90
12.00
2.03
22.40
24.80
0.82
028N0115
50SH
15.875
10.16
9.40
5.08
22.10
23.40
15.09
2.42
30.40
36.20
1.25
028P0115
60SH
19.050
11.91
12.57
5.94
29.20
31.60
18.00
3.25
44.10
50.40
1.87
028Q0115
80SH
25.400
15.88
15.75
7.92
36.20
37.70
24.00
4.00
88.20
93.00
3.10
028R0115
I00SH
31.750
19.05
18.90
9.53
43.60
46.90
30.00
4.80
116.60
129.10
4.52
028S0115
I20SH
38.100
22.23
25.22
11.10
53.50
57.50
35.70
5.60
158.20
175.30
6.60
028W0115
I40SH
44.450
25.40
25.22
12.70
57.60
62.20
41.00
6.40
206.00
266.50
8.30
028X0115
I60SH
50.800
28.58
31.55
14.27
68.20
73.00
47.80
7.20
274.00
293.00
10.30
028Z0115
200SH
63.500
39.68
37.85
19.85
86.60
93.50
60.00
9.50
506.10
562.30
19.16
11
Section : 2
chain drives
Roller Chain
ROLLER CHAINS WITH STRAIGHT SIDE PLATES
Pin
DiameteR
P
(mm)
d1 max
(mm)
b1 min
(mm)
d2 max
(mm)
Pin Length
L max
(mm)
LC max
(mm)
Plate Depth
Plate
Thickness
Minimum
Tensile
Strength
h2 max
(mm)
t/T max
(mm)
Q min
(kN)
Average
Tensile
Strength
Weight per
Metre
Q0
(kN)
q
kg/m
Pt
Width
Between
Inner Plates
Pt
Product Code
Roller
Diameter
Pt
DIN ISO
Chain No
Pitch
028B0410
C08B-1
12.700
8.51
7.75
4.45
16.70
18.20
11.80
1.60
18.00
19.50
0.80
028C0410
C10B-1
15.875
10.16
9.65
5.08
19.50
20.90
14.70
1.70
22.40
27.09
1.06
028D0410
C12B-1
19.050
12.07
11.68
5.72
22.50
25.20
16.00
1.85
29.00
32.20
1.32
028E0410
C16B-1
25.400
15.88
17.02
8.28
36.10
39.10
21.00
4.15/3.1
60.00
72.80
3.08
028E0410
C16B-/24
25.400
15.88
17.02
8.28
36.10
39.10
24.00
4.15/3.1
60.00
72.80
3.49
028F0410
C20B-1
31.750
19.05
19.56
10.19
41.30
45.00
26.40
4.5/3.5
95.00
106.70
4.16
028G0410
C24B-1
38.100
25.40
25.40
14.63
53.40
57.80
33.20
6.0/4.8
160.00
178.00
7.47
STAINLESS STEEL CHAINS

Material: AISI 304 Stainless Steel for optimum corrosion resistance,
having regard for tensile strength and wear life considerations.
Stainless steel chain is not as hard or as strong as carbon steel chain.
AISI 304 Stainless Steel may have some slight residual magnetism
due to cold working of the pins, bushes and rollers in manufacture.
For applications where non-magnetic chain is required consult your
local Authorised Distributor.
Pitch
Product Code
Chain No
P
(mm)
Width
Roller
Pin
Between
Diameter Inner
Plates Diameter
d1 max
(mm)
b1 min
(mm)
d2 max
(mm)
L max
(mm)
LC max
(mm)
h2 max
(mm)
t/T max
(mm)
Minimum
Tensile
Strength
Average
Tensile
Strength
Weight per
Metre
Q min
(kN)
Q0
(kN)
q
kg/m
028H0112
04B-1SS
6.000
4.00
2.80
1.85
6.80
7.80
5.00
0.60
2.00
2.40
0.11
028J0112
05B-1SS
8.000
5.00
3.00
2.31
8.20
8.90
7.10
0.80
3.50
4.10
0.20
028A0412
*06B-1SS
9.525
6.35
5.72
3.28
13.15
14.10
8.20
1.30
6.20
6.80
0.41
028B0112
08B-1SS
12.700
8.51
7.75
4.45
16.70
18.20
11.80
1.60
12.00
14.30
0.70
028C0112
10B-1SS
15.875
10.16
9.65
5.08
19.50
20.90
14.70
1.70
14.50
17.20
0.94
028D0112
12B-1SS
19.050
12.07
11.68
5.72
22.50
24.20
16.00
1.85
18.50
20.90
1.16
028E0112
16B-1SS
25.400
15.88
17.02
8.28
36.10
37.40
21.00
4.15/3.1
40.00
47.60
2.73
028F0112
20B-1SS
19.05
19.56
10.19
41.30
45.00
26.40
4.5/3.5
59.00
69.60
3.73
028K0112
35SS
31.750
9.525
5.08
4.77
3.58
12.40
13.17
9.00
1.30
5.50
6.60
0.33
028L0112
40SS
12.700
7.95
7.85
3.96
16.60
17.80
12.00
1.50
9.60
10.80
0.63
028N0112
50SS
15.875
10.16
9.40
5.08
20.70
22.20
15.00
2.03
15.20
17.20
1.03
028P0112
60SS
19.050
11.91
12.57
5.94
25.90
27.70
18.00
2.42
21.70
26.40
1.51
028Q0112
80SS
25.400
15.88
15.75
7.92
32.70
35.00
24.00
3.25
38.90
46.60
2.62
* Straight Side Plates.
Bushing chain, d1 indicates the external diameter of the bushing.
12
Inner Plate
Plate
Depth
Thickness
Pin Length
chain drives
Section : 2
Special Chain and Attachment Chain

AMERICAN STANDARD ROLLER CHAINS
FENNER SPECIAL CHAINS
Pitch
Roller
Diameter
Width
Between Inner
Plates
Pin
Diameter
P
(mm)
d1 max
(mm)
b1 min
(mm)
d2 max
(mm)
Chain No.
04BH
415
Also available are the extended range of Special chains which

are widely used industrial standards but not part of any ISO or
ANSI International Standards.
Pin Length
L max
(mm)
LC max
(mm)
Inner Plate
Depth
Plate
Thickness
Minimum
Tensile
Strength
Average
Tensile
Strength
Weight per
Metre
h2 max
(mm)
t/T max
(mm)
Q min
(kN)
Q0
(kN)
q
kg/m
6.00
4.00
2.80
1.85
8.40
9.40
5.00
0.90
5.00
5.30
0.14
12.70
7.77
4.76
3.60
11.00
12.40
9.70
1.00
6.86
7.60
0.32
415H
12.70
7.77
4.76
3.96
13.10
14.50
12.00
1.50
14.40
16.10
0.55
415B
12.70
7.75
4.88
4.09
12.90
14.40
10.30
1.30
12.00
14.20
0.44
415BF1
12.70
7.75
4.88
4.09
11.50
13.00
10.30
1.00
9.00
10.60
0.38
423
12.70
8.51
6.40
4.45
15.60
17.10
12.40
1.70
19.60
21.90
0.71
478
12.70
7.80
4.80
4.00
11.60
13.65
10.46
1.25
9.80
12.80
0.39
08BF
12.70
8.51
5.55
4.45
14.60
16.10
11.80
1.60
17.80
19.20
0.66
12BV
19.05
12.07
11.68
6.10
24.50
26.50
16.00
2.42
36.00
39.90
1.43
12BH
19.05
12.07
11.68
5.94
25.20
26.80
16.00
2.42
40.00
44.40
1.45
12BHF1
19.05
12.07
11.68
6.10
25.00
27.20
16.50
2.50
44.00
48.80
1.46
16BF1
25.40
15.88
12.20
8.28
31.40
32.70
21.00
4.15/3.1
60.00
71.40
2.60
16BF2
25.40
15.88
17.02
8.28
38.60
39.80
21.00
4.15
60.00
71.40
3.08
16BF5
25.40
15.88
12.70
8.28
30.80
32.10
20.00
3.5/3.0
50.00
57.50
2.37
16BH
24BH
25.40
38.10
15.88
25.40
17.02
25.40
8.90
14.63
35.70
58.60
38.90
63.40
24.10
36.20
4.0/3.1
7.5/6.0
80.00
225.00
94.20
250.30
3.11
9.00
13
Section : 2
chain drives
Double Pitch Chain
DOUBLE PITCH TRANSMISSION CHAINS
ANSI Chain
No
ISO Chain
No
A2040
208B
A2050
210B
A2060
212B
A2080
216B
Pitch
Roller
Diameter
Width
Between
Inner Plates
Pin
Diameter
P
(mm)
d1 max
(mm)
b1 min
(mm)
d2 max
(mm)
25.40
7.95
7.85
3.96
16.60
17.80
12.00
1.50
14.10
16.70
0.42
25.40
8.51
7.75
4.45
16.70
18.20
11.80
1.60
18.00
19.40
0.45
31.75
10.16
9.40
5.08
20.70
22.20
15.00
2.03
22.20
28.10
0.73
31.75
10.16
9.65
5.08
19.50
20.90
14.70
1.70
22.40
27.50
0.65
38.10
11.91
12.57
5.94
25.90
27.70
18.00
2.42
31.80
36.80
1.02
38.10
12.07
11.68
5.72
22.50
25.20
16.00
1.85
29.00
32.20
0.76
50.80
15.88
15.75
7.92
32.70
36.50
24.00
3.25
56.70
65.70
1.70
50.80
15.88
17.02
8.28
36.10
39.10
21.00
4.15/3.10
60.00
72.80
1.75
Pin Length
L max
(mm)
LC max
(mm)
Inner Plate
Depth
Plate
Thickness
Minimum
Tensile
Strength
Average
Tensile
Strength
Weight per
Metre
h2 max
(mm)
t/T max
(mm)
Q min
(kN)
Q0
(kN)
q
kg/m
DOUBLE PITCH CONVEYOR CHAINS

SMALL ROLLER TYPE
LARGE ROLLER TYPE
ANSI
Chain No
Pitch
Roller
Diameter
Width
Between Inner
Plates
Pin
Diameter
P
(mm)
d1 max
(mm)
b1 min
(mm)
d2 max
(mm)
L max
(mm)
LC max
(mm)
Inner Plate
Depth
Plate
Thickness
Minimum
Tensile
Strength
Average
Tensile
Strength
Weight per
Metre
h2 max
(mm)
t/T max
(mm)
Q min
(kN)
Q0
(kN)
q kg/m
C2040
25.40
7.95
7.85
3.96
16.60
17.80
12.00
1.50
14.10
16.70
0.50
C2042
25.40
15.88
7.85
3.96
16.60
17.80
12.00
1.50
14.10
16.70
0.84
C2050
31.75
10.16
9.40
5.08
20.70
22.20
15.00
2.03
22.20
28.10
0.78
C2052
31.75
19.05
9.40
5.08
20.70
22.20
15.00
2.03
22.20
28.10
1.27
C2060
38.10
11.91
12.57
5.94
25.90
27.70
18.00
2.42
31.80
36.80
1.12
C2062
38.10
22.23
12.57
5.94
25.90
27.70
18.00
2.42
31.80
36.80
1.61
C2060H
38.10
11.91
12.57
5.94
29.20
31.60
18.00
3.25
31.80
41.60
1.44
C2062H
38.10
22.23
12.57
5.94
29.20
31.60
18.00
3.25
31.80
41.60
2.07
C2080H
50.80
15.88
15.75
7.92
36.20
39.40
24.40
4.00
56.70
70.00
2.54
C2082H
50.80
28.58
15.75
7.92
36.20
39.40
24.40
4.00
56.70
70.00
3.58
C2100H
63.50
19.05
18.90
9.53
43.60
46.90
30.00
4.80
88.50
112.40
3.56
C2102H
63.50
39.67
18.90
9.53
43.60
46.90
30.00
4.80
88.50
112.40
5.38
C2120H
76.20
22.23
25.22
11.10
53.50
57.50
35.70
5.60
127.00
160.90
5.26

14
Pin Length
chain drives
Section : 2
Special Chain and Attachment Chain

DOUBLE PITCH TRANSMISSION CHAINS
TYPE A - BUSHED
TYPE B - BUSHED
TYPE C - ROLLER
Pitch
Chain No
P
(mm)
Width
Bush / Roller Between
Diameter Inner Plates
d1 max
(mm)
b1 min
(mm)
Pin Diameter
d2 max
(mm)
Pin Length
d3 max
(mm)
L max
(mm)
LC max
(mm)
Inner Plate
Depth
Plate
Thickness
h2 max
(mm)
t/T max
(mm)
Minimum
Tensile
Strength
Average
Tensile
Strength
Weight per
Metre
Q min kN)
Q0
(kN)
q
kg/m
Type
08BHP
12.700
8.51
7.75
6.55
4.50
16.40
17.60
11.80
1.60/1.30
11.10
12.10
0.56
10BHP
15.875
10.16
9.65
5.94
4.04
19.30
20.60
14.70
1.70
17.00
20.80
0.86
12BHP
19.050
12.07
11.68
6.50
4.00
21.60
22.80
15.90
1.85
23.60
25.90
1.09
40HP
12.700
7.95
7.85
5.63
4.00
16.50
17.60
12.00
1.50
11.00
12.20
0.54
50HP
15.875
10.16
9.40
7.03
5.13
20.70
21.90
15.09
2.03
20.00
22.60
0.91
60HP/5.01
19.050
11.91
12.70
7.00
5.01
25.50
26.60
18.00
2.42
20.00
22.40
1.35
60HP/6.00
19.050
11.91
12.70
8.31
6.00
25.80
26.80
18.00
2.42
24.00
26.90
1.29
80HP
25.400
15.88
15.75
11.40
8.05
32.50
33.80
24.00
3.25
50.00
58.30
2.26
C2040HP
25.400
7.95
7.85
5.63
4.00
16.50
17.60
12.00
1.50
11.00
12.60
0.46
C2050HP
31.750
10.16
9.40
7.22
5.12
20.50
21.80
15.00
2.03
20.40
22.80
0.76
C2060HP
38.100
11.91
12.70
8.31
6.00
25.80
26.80
18.00
2.42
24.00
27.10
1.02
C2080HP
50.800
15.88
15.75
11.40
8.05
32.50
33.80
24.00
3.25
50.00
55.20
1.81
15
Section : 2
chain drives
Agricultural Chain
'S' TYPE STEEL AGRICULTURAL CHAINS
All 'S' type chain and attachments can be supplied zinc plated. Please specify at time of order.
Pitch
Roller
Diameter
P
(mm)
d1 max
(mm)
Chain No
Width
Between Inner Pin Diameter
Plates
b1 min
(mm)
d2 max
(mm)
Pin Length
L max
(mm)
LC max
(mm)
Inner Plate
Depth
Plate
Thickness
Minimum
Tensile
Strength
Average
Tensile
Strength
Weight per
Metre
h2 max
(mm)
t/T max
(mm)
Q mim
(kN)
Q0
(kN)
q
kg/m
S32
29.21
11.43
15.88
4.45
26.70
28.80
13.20
1.80
18.00
21.60
0.86
S42
34.93
14.27
19.05
7.00
34.30
37.00
19.80
2.80
27.00
50.80
1.60
S45
41.40
15.24
22.23
5.72
37.70
40.40
17.30
2.80
18.00
36.10
1.66
S52
38.10
15.24
22.23
5.72
37.70
40.40
17.30
2.80
18.00
36.10
1.68
S55
41.40
17.78
22.23
5.72
37.70
40.40
17.30
2.80
18.00
36.10
1.80
S55R
41.40
17.78
22.23
8.90
41.00
44.00
22.40
3.50
45.00
73.10
2.49
S62
41.91
19.05
25.40
5.72
40.30
43.00
17.30
2.50
27.00
36.10
1.87
S77
58.34
18.26
22.23
8.90
43.20
46.40
26.20
4.00
45.00
73.10
2.65
S88
66.27
22.86
28.58
8.90
49.80
53.00
26.20
4.00
45.00
73.10
3.25
Fenner Classic
> Shot peened rollers and side plates

> Case hardened pins
Robust chain for everyday use
> Solid rollers for increased wear life
Contact you local Authorised Distributor for more information
> BS and ANSI ranges available
16
> Fit and forget reliability

> Stainless steel product available
chain drives
Section : 2
Leaf Chain
BL SERIES LEAF CHAINS
CHAIN LACING
Pitch
ANSI Chain No
ISO Chain No
P
(mm)
BL422
BL423
BL434
BL444
BL446
BL466
BL522
BL523
BL534
BL544
BL546
BL566
LH0822
LH0823
LH0834
LH0844
LH0846
LH0866
LH1022
LH1023
LH1034
LH1044
LH1046
LH1066
BL622
BL623
BL634
BL644
BL646
BL666
LH1222
LH1223
LH1234
LH1244
LH1246
LH1266
BL822
BL823
BL834
BL844
BL846
BL866
LH1622
LH1623
LH1634
LH1644
LH1646
LH1666
BL1022
BL1023
BL1034
BL1044
BL1046
BL1066
LH2022
LH2023
LH2034
LH2044
LH2046
LH2066
BL1222
BL1223
BL1234
BL1244
BL1246
BL1266
LH2422
LH2423
LH2434
LH2444
LH2446
LH2466
BL1422
BL1423
BL1434
BL1444
BL1446
BL1466
LH2822
LH2823
LH2834
LH2844
LH2846
LH2866
BL1622
BL1623
BL1634
BL1644
BL1646
BL1666
LH3222
LH3223
LH3234
LH3244
LH3246
LH3266
Plate Depth
Plate
Thickness
Pin Diameter
h2 max
(mm)
t/T max
(mm)
d2 max
(mm)
Chain Lacing
12.700
1/2"
15.875
5/8"
2x2
2x3
3x4
4x4
4x6
6x6
2x2
2x3
3x4
4x4
4x6
6x6
19.050
3/4"
2x2
2x3
3x4
4x4
4x6
6x6
25.400
1"
2x2
2x3
3x4
4x4
4x6
6x6
31.750
1.1/4"
2x2
2x3
3x4
4x4
4x6
6x6
38.100
1.1/2"
2x2
2x3
3x4
4x4
4x6
6x6
44.450
1.3/4"
2x2
2x3
3x4
4x4
4x6
6x6
50.800
2"
2x2
2x3
3x4
4x4
4x6
6x6
12.07
15.09
18.11
24.13
30.18
36.20
42.24
48.26
Q min
(kN)
22.20
22.20
33.40
44.50
44.50
66.70
33.40
33.40
48.90
66.70
66.70
100.10
27.60
27.60
41.40
56.00
56.00
81.70
43.10
43.10
65.60
84.50
84.50
125.10
7.94
17.37
20.73
27.43
30.78
37.49
44.20
48.90
48.90
75.60
97.90
97.90
146.80
63.60
63.60
102.80
120.90
120.90
190.80
1.45
1.80
2.50
2.90
3.60
4.30
9.54
21.34
25.48
33.76
37.90
46.18
54.46
84.50
84.50
129.00
169.00
169.00
253.60
108.20
108.20
170.00
214.60
214.60
324.50
2.20
2.70
3.80
4.30
5.40
6.50
11.11
25.37
30.33
40.23
45.19
55.09
65.00
115.60
115.60
182.40
231.30
231.30
347.00
150.80
150.80
231.60
291.40
291.40
430.30
3.40
4.30
6.00
6.90
8.60
10.30
12.71
29.62
35.43
47.07
52.88
64.52
76.15
151.20
151.20
244.60
302.50
302.50
453.70
192.00
192.00
315.90
381.10
381.10
543.60
4.60
5.80
8.10
9.30
11.60
13.90
14.29
33.55
40.16
53.37
59.97
73.18
86.39
191.30
191.30
315.80
382.60
382.60
578.30
225.70
225.70
372.60
451.20
451.20
682.40
6.10
7.60
10.60
12.20
15.20
18.20
17.46
39.01
46.58
61.72
69.29
84.43
99.57
289.10
289.10
440.40
578.30
578.30
857.40
341.10
341.10
519.60
680.40
680.40
1000.70
8.00
10.00
14.00
16.00
20.00
24.00
2.44
5.96
4.90
5.77
6.55
7.52
Q0
(kN)
Weight per
Metre
q
kg/m
0.64
0.80
1.12
1.28
1.60
1.92
0.88
1.10
1.50
1.80
2.20
2.65
5.09
4.09
Minimum
Average Tensile
Tensile Strength
Strength
L max
(mm)
11.05
13.16
17.40
19.51
23.75
27.99
12.90
15.37
20.32
22.78
27.74
32.69
2.08
3.30
Pin Length
17
Section : 2
chain drives
Leaf Chain
LL SERIES LEAF CHAINS
ISO Chain
No
LL0822
LL0844
LL0866
LL1022
LL1044
LL1066
LL1088
LL1222
LL1244
LL1266
LL1288
LL1622
LL1644
LL1666
LL1688
LL2022
LL2044
LL2066
LL2088
LL2422
LL2444
LL2466
LL2488
LL2822
LL2844
LL2866
LL2888
LL3222
LL3244
LL3266
LL3288
LL4022
LL4044
LL4066
LL4088
LL4822
LL4844
LL4866
LL4888
Pitch
P
(mm)
12.700
1/2"
15.875
5/8"
19.050
3/4"
25.400
1"
31.750
1.1/4"
38.100
1.1/2"
44.450
1.3/4"
50.800
2"
63.500
2.1/2"
76.200
3"
Chain
Lacing
2x2
4x4
6x6
2x2
4x4
6x6
8x8
2x2
4x4
6x6
8x8
2X2
4X4
6X6
8X8
2X2
4X4
6X6
8X8
2X2
4X4
6X6
8X8
2X2
4X4
6X6
8X8
2X2
4X4
6X6
8X8
2X2
4X4
6X6
8X8
2X2
4X4
6X6
8X8
Plate
Depth
Minimum
Plate
Pin
Tensile
Thickness Diameter Pin Length Strength
h2 max
(mm)
t/T max
(mm)
d2 max
(mm)
10.60
1.30
4.45
13.70
1.60
5.08
16.00
1.85
5.72
21.0
3.10
8.28
26.40
3.70
10.19
33.40
5.00
14.63
37.08
6.00
15.90
42.00
6.00
17.81
52.76
8.25
22.89
63.88
10.30
29.24
L max
(mm)
7.60
13.00
18.20
9.20
15.80
22.10
28.80
10.40
17.90
25.40
32.90
17.20
29.60
42.40
55.40
20.10
33.80
50.10
65.40
28.40
46.30
66.40
86.60
32.20
56.40
80.60
105.20
33.20
57.40
81.60
105.00
44.70
77.90
111.10
145.50
56.10
97.40
138.90
182.40
Q min
(kN)
17.80
31.10
44.50
22.30
44.50
66.70
89.00
28.90
57.80
86.70
115.60
58.00
144.00
200.00
288.00
95.00
190.00
285.00
380.00
170.00
340.00
510.00
680.00
200.00
400.00
600.00
800.00
260.00
520.00
780.00
1050.00
360.00
780.00
1080.00
1560.00
560.00
1120.00
1168.00
2240.00
Average Weight per

Tensile
Metre
Strength
Q0
(kN)
20.40
35.70
50.90
25.50
51.00
76.30
101.90
33.20
66.40
99.70
132.90
66.70
164.60
230.00
331.20
109.20
218.50
324.60
435.10
195.50
380.80
571.20
775.20
224.00
448.00
672.00
896.00
291.20
582.40
873.60
1176.00
703.20
873.60
1209.60
1747.20
627.20
1554.40
1308.10
2508.80
q
kg/m
0.35
0.69
1.00
0.54
1.06
1.57
2.10
0.73
1.44
2.15
2.84
1.52
2.90
4.30
5.71
2.33
4.40
6.79
8.75
4.47
8.22
12.22
16.30
5.10
9.90
14.60
19.40
5.80
11.40
16.90
24.00
10.30
20.00
29.50
39.10
18.50
35.70
53.00
70.40
AL SERIES LEAF CHAINS

ANSI
Chain No
AL322
AL422
AL444
AL466
AL522
AL534
AL544
AL566
AL622
AL644
AL666
AL822
AL844
AL866
AL1022
AL1044
AL1066
AL1222
AL1244
AL1266
AL1444
AL1466
AL1644
AL1666
18
Pitch
P
(mm)
9.525 3/8"
12.700
1/2"
15.875
5/8"
19.050
3/4"
25.400
1"
31.750
1.1/4"
38.100
1.1/2"
44.450
1.3/4"
50.800
2"
Chain
Lacing
2X2
2X2
4X4
6X6
2X2
3X4
4X4
6X6
2X2
4X4
6X6
2X2
4X4
6X6
2X2
4X4
6X6
2X2
4X4
6X6
4X4
6X6
4X4
6X6
Plate
Depth
h2 max
(mm)
7.70
Plate
Pin
Thickness Diameter
t/T max
(mm)
1.30
d2 max
(mm)
3.58
10.40
1.50
3.96
12.80
2.03
5.08
15.60
2.42
5.94
20.50
3.25
7.92
25.60
4.00
9.53
30.50
4.80
11.10
36.40
5.60
12.64
41.60
6.40
14.21
Pin Length Minimum

Tensile
Strength
L max
(mm)
6.80
7.90
14.40
20.50
10.30
17.00
18.90
26.90
12.40
22.70
32.40
16.00
29.40
42.50
19.60
35.90
52.30
24.30
43.80
63.00
51.30
74.56
58.06
84.46
Q min
(kN)
9.00
14.10
28.20
42.30
22.00
33.00
44.00
66.00
37.00
64.00
101.00
56.70
113.40
170.00
88.50
177.00
265.00
127.00
254.00
381.00
372.70
559.00
471.00
706.00
Average Weight per

Tensile
Metre
Strength
Q0
(kN)
10.20
16.90
35.20
52.70
27.50
46.00
55.00
82.50
44.40
78.80
118.60
68.60
135.60
202.30
107.10
203.60
315.30
151.10
299.70
426.30
413.60
620.40
522.80
783.60
CHAIN LACING
q
kg/m
0.23
0.39
0.74
1.10
0.61
1.10
1.19
1.79
0.86
1.69
2.52
1.54
3.00
4.46
2.37
4.68
7.00
3.65
7.05
10.44
10.34
15.16
12.98
19.41
CHAIN LACING
Section : 2
Fenner PLUS Chain

High Performance Roller Chain
> Enhanced performance in hostile

environments
> Operates successfully with irregular
lubrication
> Shot peened plates for fatigue resistance
> Special wax lubrication as standard
> Case hardened bearing pins for wear and
'stretch' resistance
> EPX Easy Pin eXtraction feature
The Mark of Engineering Excellence
www.fptgroup.com
Section : 2
chain drives
Taper Lock Sprockets
TYPE 1
TYPE 2
TYPE 3
TYPE 4
TYPE 5
STEEL C45
TYPE 6
TYPE 7
TYPE 8
TYPE 9
CAST IRON GG22
06B T/L SPROCKET 3/8" (9.5mm) PITCH

Tooth Width
B1 5.3mm
b1 5.2mm
B2 15.4mm
B3 25.6mm
Pitch Dia Outer
Dia
No.of
Teeth
dp
de
(mm)
(mm)
Dia
Over
Chain
A
(mm)
Simplex Taper Lock

Product
code
Desig- Bush Type

nation No.
L
(mm)
N
(mm)
Product
code
Desig- Bush Type

nation No.
Length Hub
Bore Dia
L
(mm)
N
(mm)
Product
code
Desig- Bush Type

nation No.
Length Hub
Bore Dia
L
(mm)
N
(mm)
17
51.84
56
60
026A0117
3117
1008
22.2
45
026A0217
3217
1008
22.2
45
026A0317 3317
1008
25.6
19
57.86
62
66
026A0119
3119
1008
22.2
45
026A0219
3219
1008
22.2
45
026A0319 3319
1008
25.6
20
60.89
64
68
026A0120
3120
1008
22.2
46
21
63.91
68
72
026A0121
3121
1008
22.2
46
026A0221
3221
1008
22.2
49
026A0321 3321
1008
25.6
23
69.95
74
78
026A0123
3123
1210
25.4
63
026A0223
3223
1210
25.4
59
026A0323 3323
1210
25.6
25
76.00
80
84
026A0125
3125
1210
25.4
63
026A0225
3225
1210
25.4
65
026A0325 3325
1210
25.6
27
82.05
86
90
026A0127
3127
1210
25.4
63
026A0227
3227
1210
25.4
70
026A0327 3327
1210
25.6
30
91.12
95
99
026A0130
3130
1210
25.4
63
026A0230
3230
1210
25.4
75
026A0330 3330
1615
38.0
79
38
115.34
119
123
026A0138
3138
1210
25.4
70
026A0238
3238
1610
25.4
80
026A0338 3338
1615
38.0
90
45
136.55
141
145
026A0145
3145
1210
25.4
70
026A0245
3245
1610
25.4
80
57
172.90
177
181
026A0157
3157
1210
25.4
83
026A0257
3257
1610
25.4
80
76
230.48
234
239
026A0176
3176
1210
25.4
83
026A0276
3276
1610
25.4
92
95
288.08
292
296
026A0195
3195
1210
25.4
83
026A0295
3295
1610
25.4
92
Taper Lock bushes supplied as a separate items

20
Triplex Taper Lock
Duplex Taper Lock

Length Hub
Bore Dia
chain drives
Section : 2

08B T/L SPROCKET " (12.7mm) PITCH
Tooth Width
B1 7.2mm
b1 7.0mm
B2 21.0mm
B3 34.9mm
No.of
Teeth
Pitch
Dia.
dp
(mm)
Dia
Outer Over
Dia Chain
de
(mm)
A
(mm)
Simplex Taper Lock
Product
code
Desig- Bush Type

nation No.
Triplex Taper Lock
Duplex Taper Lock

Length Hub
Bore Dia
L
(mm)
N
(mm)
Product
code
Desig- Bush
nation No.
Type
Length Hub
Bore Dia
L
(mm)
N
(mm)
Product
code
Desig- Bush Type

nation No.
Length Hub
Bore Dia
L
(mm)
15
61.09
66
73
026B0115
4115
1008
22.2
45
026B0215
4215
1008
22.2
46
026B0315
4315
1008
34.9
17
69.11
74
81
026B0117
4117
1210
25.4
60
026B0217
4217
1210
25.4
56
026B0317
4317
1210
34.9
19
77.17
82
89
026B0119
4119
1210
25.4
63
026B0219
4219
1210
25.4
62
026B0319
4319
1210
34.9
20
81.19
86
93
026B0120
4120
1610
25.4
65
21
85.22
90
97
026B0121
4121
1610
25.4
71
026B0221
4221
1610
25.4
70
026B0321
4321
1610
34.9
23
93.27
99
106
026B0123
4123
1610
25.4
76
026B0223
4223
1610
25.4
79
026B0323
4323
1610
34.9
25
101.32
106
113
026B0125
4125
1610
25.4
76
026B0225
4225
2012
32.0
87
026B0325
4325
2012
34.9
27
109.40
114
121
026B0127
4127
1610
25.4
76
026B0227
4227
2012
32.0
87
026B0327
4327
2012
34.9
30
121.50
126
133
026B0130
4130
2012
32.0
90
026B0230
4230
2012
32.0
87
026B0330
4330
2012
34.9
38
153.80
159
166
026B0138
4138
2012
32.0
90
026B0238
4238
2012
32.0
100
026B0338
4338
2012
34.9
45
57
182.07
188
195
026B0145
4145
2012
32.0
100
026B0245
4245
2012
32.0
100
230.53
236
243
026B0157
4157
2012
32.0
110
026B0257
4257
2012
32.0
110
76
307.31
312
319
026B0176
4176
2012
32.0
110
026B0276
4276
2012
32.0
110
95
384.10
389
396
026B0195
4195
2012
32.0
110
026B0295
4295
2012
32.0
110
N
(mm)
Taper Lock bushes supplied as a separate item
10B T/L SPROCKET 5/8" (15.9mm) PITCH

Tooth Width
B1 9.1mm
b1 9.0mm
B2 25.5mm
B3 42.1mm
No .of
Teeth
Pitch
dp
(mm)
Dia
Outer Over
Dia Chain
de
(mm)
A
(mm)
Simplex Taper Lock

Product
code
Desig- Bush Type

nation No.
Triplex Taper Lock
Duplex Taper Lock

Length Hub
Bore Dia
L
(mm)
N
(mm)
Product
code
Desig- Bush Type

nation No.
Length Hub
Bore Dia
L
(mm)
N
(mm)
Product
code
Desig- Bush Type

nation No.
Length Hub
Bore Dia
L
(mm)
N
(mm)
13
66.34
73
81
026C0113
5113
1008
22.2
47
15
76.35
83
91
026C0115
5115
1210
25.4
60
026C0215
5215
1210
25.4
026C0315
5315
1210
42.1
17
86.39
93
101
026C0117
5117
1210
25.4
71
026C0217
5217
1610
25.4
026C0317
5317
1210
42.1
19
96.44
103
111
026C0119
5119
1610
25.4
75
026C0219
5219
1610
25.4
026C0319
5319
1615
42.1
20
21
101.49
108
116
026C0120
5120
1610
25.4
76
106.50
114
122
026C0121
5121
1610
25.4
76
026C0221
5221
1610
25.4
026C0321
5321
1615
42.1
23
116.59
124
132
026C0123
5123
1610
25.4
76
026C0223
5223
1610
25.4
026C0323
5323
2012
42.1
25
27
126.67
134
142
026C0125
5125
2012
32.0
90
026C0225
5225
2012
32.0
90
026C0325
5325
2517
45.0
105
136.75
144
152
026C0127
5127
2012
32.0
90
026C0227
5227
2012
32.0
90
026C0327
5327
2517
45.0
110
30
151.87
159
167
026C0130
5130
2012
32.0
90
026C0230
5230
2012
32.0
90
026C0330
5330
2517
45.0
120
38
192.23
200
208
026C0138
5138
2012
32.0
100
45
227.58
235
243
026C0145
5145
2012
32.0
100
57
288.19
296
304
026C0157
5157
2012
32.0
110
76
384.15
392
400
026C0176
5176
2012
32.0
110
Taper Lock bushes supplied as a separate items
21
Section : 2
chain drives

12B T/L SPROCKET " (19.0mm) PITCH
Tooth Width
B1 11.1mm
b1 10.8mm
B2 30.3mm
B3 49.8mm
No.of
Teeth
Pitch
Dia
Dia
Outer Over
Dia Chain
dp
(mm)
de
(mm)
A
(mm)
Simplex Taper Lock

Product
code
Desig- Bush Type

nation No.
Triplex Taper Lock
Duplex Taper Lock

Length Hub
Bore Dia
L
(mm)
N
(mm)
Product
code
Desig- Bush Type

nation No.
Length Hub
Bore Dia
L
(mm)
N
(mm)
Product
code
Desig- Bush Type

nation No.
Length Hub
Bore Dia
L
(mm)
13
79.60
88
96
026D0113
6113
1210
25.4
60
15
91.62
100
108
026D0115
6115
1610
25.4
70
026D0215
6215
1610
25.4
026D0315
6315
1615
49.8
17
103.68
112
120
026D0117
6117
1610
25.4
76
026D0217
6217
1610
25.4
026D0317
6317
2012
49.8
026D0219
6219
2012
32.0
026D0319
6319
2012
49.8
19
115.75
124
132
026D0119
6119
2012
32.0
90
20
121.78
130
138
026D0120
6120
2012
32.0
95
90
21
127.81
136
144
026D0121
6121
2517
44.5
102
026D0221
6221
2517
44.5
108
026D0321
6321
2517
49.8
23
139.90
149
157
026D0123
6123
2517
44.5
108
026D0223
6223
2517
44.5
108
026D0323
6323
2517
49.8
N
(mm)
25
151.99
160
168
026D0125
6125
2517
44.5
108
026D0225
6225
2517
44.5
130
026D0325
6325
2517
49.8
27
164.09
172
180
026D0127
6127
2517
44.5
108
026D0227
6227
2517
44.5
130
026D0327
6327
3020
50.8
140
30
182.25
191
197
026D0130
6130
2517
44.5
108
026D0230
6230
2517
44.5
130
026D0330
6330
3020
50.8
140
38
230.68
239
247
026D0138
6138
2517
44.5
108
026D0238
6238
3020
50.8
140
026D0338
6338
3020
50.8
140
45
273.10
283
291
026D0145
6145
2517
44.5
108
026D0245
62-45
3020
50.8
140
026D0345
63-45
3020
50.8
140
57
345.82
355
363
026D0157
6157
2517
44.5
124
026D0257
6257
3020
50.8
160
026D0357
6357
3020
50.8
150
76
460.98
470
478
026D0176
6176
2517
44.5
124
026D0276
6276
3020
50.8
160
026D0376
6376
3020
50.8
160
95
576.17
585
593
026D0195
6195
2517
44.5
124
026D0295
6295
3020
50.8
160
16B T/L SPROCKET 1" (25.4mm) PITCH

Tooth Width
B1 16.2mm
b1 15.8mm
B2 47.7mm
B3 79.6mm
No.of
Teeth
Pitch
Dia
dp
(mm)
Dia
Outer Over
Dia Chain
de
(mm)
A
(mm)
Simplex Taper Lock
Product
code
Length Hub
Bore Dia
L
(mm)
Product
code
N
(mm)
Desig- Bush Type

nation No.
Length Hub
Bore Dia
L
(mm)
N
(mm)
Product
code
Desig- Bush Type

nation No.
Length Hub
Bore Dia
L
(mm)
N
(mm)
13
106.15
117
127
026E0113
8113
1610
38.1
73
15
122.17
133
143
026E0115
8115
1610
38.1
76
026E0215
8215
2012
44.5
17
138.23
149
159
026E0117
8117
2012
32.0
90
026E0217
8217
2517
44.5
026E0317
8317
2517
76.2
19
154.33
165
175
026E0119
8119
2517
44.5
108
026E0219
8219
2517
44.5
026E0319
8319
3030
76.2
20
162.38
173
183
026E0120
8120
2517
44.5
108
026E0220
82-20
2517
44.5
21
170.43
181
191
026E0121
8121
2517
44.5
110
026E0221
8221
3020
50.8
140
026E0321
8321
3030
76.2
23
186.54
198
208
026E0123
8123
2517
44.5
110
026E0223
8223
3020
50.8
140
026E0323
8323
3525
89.0
25
202.67
214
224
026E0125
8125
2517
44.5
110
026E0225
8225
3020
50.8
140
026E0325
8325
3525
89.0
27
218.79
230
240
026E0127
8127
2517
44.5
110
026E0227
8227
3020
50.8
140
026E0327
8327
3525
89.0
30
243.00
254
264
026E0130
8130
3020
50.8
140
026E0230
8230
3020
76.2
140
026E0330
8330
3525
89.0
38
307.59
321
331
026E0138
8138
3020
50.8
140
026E0238
8238
3020
76.2
140
026E0338
8338
3525
89.0
175
45
364.13
377
387
026E0145
8145
3020
50.8
140
026E0245
8245
3020
76.2
140
026E0345
8345
4030
102.0
215
57
461.09
474
484
026E0157
8157
3020
50.8
157
026E0257
8257
3525
89.0
175
026E0357
8357
4030
102.0
215
76
614.63
627
637
026E0176
8176
3020
50.8
157
026E0276
8276
3525
89.0
175
026E0376
8376
4030
102.0
215
22
Desig- Bush Type

nation No.
Triplex Taper Lock
Duplex Taper Lock
chain drives
Section : 2
Pilot Bored Sprockets

05B PILOT BORED SPROCKET 8 X 3mm PITCH
No. of
Teeth
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
45
57
76
95
114
Pitch
Dia
Outer
Dia
dp
de
20.90
23.39
25.89
28.39
30.91
33.42
35.95
38.48
41.01
43.53
46.07
48.61
51.14
53.68
56.21
58.75
61.29
63.83
66.37
68.91
71.45
73.99
76.53
79.08
81.61
84.16
86.70
89.25
91.79
94.33
96.88
99.42
101.97
114.69
145.22
193.59
241.96
290.33
24.00
26.60
29.20
31.70
34.20
36.70
39.20
41.70
44.30
46.80
49.30
51.90
54.40
57.00
59.50
62.00
64.60
67.50
69.50
72.20
74.80
77.30
79.80
82.40
84.90
87.50
90.00
92.50
95.00
97.60
100.20
102.70
105.30
118.00
148.60
197.70
246.10
294.50
Duplex (027J02--)
Simplex (027J01--)
Hub Length Stock
Hub Length Stock
Dia Bore Bore Type Dia Bore Bore Type
N
L
D
N
L
D
13
15
17
18
20
23
25
28
30
30
30
30
30
35
35
35
35
35
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
58
78
78
78
88
12
12
12
13
13
13
13
13
14
14
14
14
14
14
14
14
14
14
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
20
20
34
34
39
06B PILOT BORED SPROCKET

No. of
Teeth
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
45
57
76
95
114
Pitch
Dia
Outer
Dia
dp
de
24.89
27.85
30.82
33.80
36.80
39.79
42.80
45.81
48.82
51.83
54.85
57.87
60.89
63.91
66.93
69.95
72.97
76.00
79.02
82.05
85.07
88.09
91.12
94.15
97.17
100.20
103.23
106.26
109.29
112.32
115.35
118.37
121.40
136.55
172.91
230.49
288.08
345.68
28.00
31.00
34.00
37.00
40.00
43.00
46.30
49.30
52.30
55.30
58.30
61.30
64.30
68.00
71.00
73.50
77.00
80.00
83.00
86.00
89.00
92.00
94.70
98.30
101.30
104.30
107.30
110.40
113.43
116.40
119.50
122.50
125.50
140.70
176.90
234.50
292.50
350.30
6
6
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
13
15
17
19
21
24
26
29
32
34
37
39
40
40
40
40
40
40
50
50
50
50
50
60
60
60
60
60
60
60
60
60
60
78
78
78
88
88
18
18
18
18
18
18
18
18
20
20
20
20
20
20
20
20
20
20
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
38
38
38
43
43
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
Tooth Width
B1 2.8mm
b1 2.7mm
B2 8.3mm
Type A = Steel C45

Type B = Cast Iron GG22
To complete the product code insert the number of teeth required (027J0109 = 05B-1 8mm pitch 9 tooth pilot
bore sprocket)
/8" X 7/32" PITCH
Tooth Width
B1 5.3mm
b1 5.2mm
Hub Length Stock
Hub Length Stock
Hub Length Stock
Dia Bore Bore Type Dia Bore Bore Type Dia Bore Bore Type B2 15.4mm
B3 25.6mm
N
L
D
N
L
D
N
L
D
Simplex (027A01--)
15
16
20
22
25
28
31
34
37
40
43
45
46
48
50
52
54
57
60
60
60
60
60
65
65
65
65
65
70
70
70
70
70
70
70
70
80
80
22
22
22
25
25
25
25
25
28
28
28
28
28
28
28
28
28
28
28
28
28
28
30
30
30
30
30
30
30
30
30
30
30
32
32
32
40
40
8
8
8
8
8
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
14
14
14
14
14
14
14
14
14
14
19
19
19
19
20
Triplex (027A03--)
Duplex (027A02--)
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
15
18
20
22
25
28
31
34
37
40
43
46
49
52
55
58
61
64
67
70
73
76
79
80
80
80
80
80
90
90
90
90
90
80
80
80
80
95
22
22
22
25
25
25
25
25
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
32
32
32
32
45
8
8
8
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
16
16
16
16
16
16
16
16
16
16
19
19
19
19
20
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
15
18
20
22
25
28
31
34
37
40
43
46
49
52
55
58
61
64
67
70
73
76
79
80
80
80
85
85
90
90
90
90
90
90
90
100
100
100
32
32
32
35
35
35
35
35
35
35
35
35
35
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
56
56
56
56
56
8
8
10
10
10
10
12
12
12
12
12
12
12
14
14
14
14
14
14
14
14
14
14
16
16
16
16
16
16
16
16
16
16
24
24
24
24
24
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
FINISHED BORES
For bore and keywayed sprockets,
the maximum finished bore
diameter is normally hub diameter
N 1.5
Type A = Steel C45

23
Section : 2
chain drives

No. of
Teeth
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
45
57
76
95
114
Pitch
Dia
Outer
Dia
dp
de
33.18
37.13
41.10
45.07
49.07
53.06
57.07
61.09
65.10
69.11
73.14
77.16
81.19
85.22
89.24
93.27
97.29
101.33
105.36
109.40
113.42
117.46
121.50
125.54
129.56
133.60
137.64
141.68
145.72
149.76
153.80
157.83
161.87
182.07
230.54
307.33
384.11
460.91
37.20
41.00
45.20
48.70
53.00
57.40
61.80
65.50
69.50
73.60
77.80
81.70
85.80
89.70
93.80
98.20
101.80
105.80
110.00
114.00
118.00
122.00
126.10
130.20
134.30
138.40
142.60
146.70
151.00
154.60
158.60
162.70
166.80
188.00
236.40
313.30
390.10
466.90
Tooth Width
Triplex (027B03--)
Simplex (027B01--)
Duplex (027B02--)
B1
7.2mm
Hub Length Stock
Hub Length Stock
Hub Length Stock
b1 7.0mm
Dia Bore Bore Type Dia Bore Bore Type Dia Bore Bore Type
B2 21.0mm
B3 34.9mm
N
L
D
N
L
D
N
L
D
20
24
26
29
33
37
41
45
50
52
56
60
64
68
70
70
70
70
70
70
70
80
80
90
90
90
90
90
90
90
90
90
90
70
70
80
80
80
25
25
25
25
28
28
28
28
28
28
28
28
28
28
28
28
28
28
30
30
30
30
30
30
30
30
30
30
35
35
35
35
35
40
40
40
45
45

No. of
Teeth
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
45
57
76
95
114
24
Pitch
Dia
Outer
Dia
dp
de
41.48
46.42
51.37
56.34
61.34
66.32
71.34
76.36
81.37
86.39
91.42
96.45
101.49
106.52
111.55
116.58
121.62
126.66
131.70
136.75
141.78
146.83
151.87
156.92
161.95
167.00
172.05
177.10
182.15
187.20
192.24
197.29
202.34
227.58
288.18
384.16
480.14
576.13
47.00
52.60
57.50
63.00
68.00
73.00
78.00
83.00
88.00
93.00
98.30
103.30
108.40
113.40
118.00
123.40
128.30
134.00
139.00
144.00
148.70
153.80
158.80
163.90
168.90
174.50
179.00
184.10
189.10
194.20
199.20
204.20
209.30
235.00
296.00
392.10
488.50
584.10
" X 5/16" PITCH
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
14
14
14
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
19
19
23
23
24
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
20
24
28
32
35
38
42
46
50
54
58
62
66
70
70
70
75
80
85
85
90
95
100
100
100
100
100
100
100
100
100
100
100
90
90
100
100
100
32
32
32
35
35
35
35
35
35
35
35
35
35
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
50
50
56
56
63
10
10
10
12
12
12
12
12
14
14
14
14
14
16
16
16
16
16
16
16
16
16
16
20
20
20
20
20
20
20
20
20
20
23
23
23
23
24
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
20
24
28
32
35
38
42
46
50
54
58
62
66
70
70
70
75
80
85
85
90
95
100
110
110
110
110
110
120
120
120
120
120
100
100
100
120
120
46
46
46
50
50
50
50
50
50
50
50
50
50
55
55
55
55
55
55
55
55
55
55
55
55
55
55
55
55
55
55
55
55
60
60
60
67
67
10
12
12
14
14
14
14
14
16
16
16
16
16
16
16
16
16
16
20
20
20
20
20
20
20
20
20
20
25
25
25
25
25
24
24
24
24
24
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
25
25
25
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
35
35
35
35
35
35
35
35
35
35
35
35
35
35
35
40
45
50
56
56
To complete the product code insert the number of teeth required (027B0109 =
08B-1 " pitch 9 tooth pilot bore sprocket)
/8" X 3/8" PITCH
Triplex (027C03--)
Simplex (027C01--)
Duplex (027C02--)
Hub Length Stock
Hub Length Stock
Hub Length Stock
N
L
D
N
L
D
N
L
D
25
30
35
37
42
47
52
57
60
60
70
70
75
75
80
80
80
80
85
85
90
90
90
95
95
95
95
95
100
100
100
100
100
80
90
90
100
100
Type A = Steel C45

10
10
10
12
12
12
12
12
12
12
14
14
14
16
16
16
16
16
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
19
23
23
23
24
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
25
30
35
39
44
49
54
59
64
69
74
79
84
85
90
95
100
105
110
110
115
115
120
120
120
120
120
120
120
120
120
120
120
100
100
100
110
125
40
40
40
40
40
40
40
40
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
45
50
56
63
63
70
12
12
12
14
14
14
14
14
16
16
16
16
16
16
16
16
16
16
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
30
30
30
30
30
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
25
30
35
39
44
49
54
59
64
69
74
79
84
85
90
95
100
105
110
110
115
115
120
120
120
120
120
120
120
120
120
120
120
100
100
110
125
125
55
55
55
55
55
55
55
55
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
60
63
67
70
80
12
12
16
16
16
16
16
16
16
16
16
16
16
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
25
25
25
25
25
32
32
35
35
35
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
Tooth Width
B1
9.1mm
b1 9.0mm
B2 25.5mm
B3 42.1mm
FINISHED BORES
N 1.5
Type A = Steel C45

To complete the product code insert the number of teeth required (027C0109 =
10B-1 5/8" pitch 9 tooth pilot bore sprocket)
chain drives
Section : 2

12B PILOT BORED SPROCKETS " X 7/16" PITCH
No. of
Teeth
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
45
57
76
95
114
Pitch
Dia
Outer
Dia
dp
de
49.78
55.70
61.64
67.61
73.61
79.59
85.61
91.63
97.65
103.67
109.71
115.75
121.78
127.82
133.86
139.90
145.94
152.00
158.04
164.09
170.13
176.19
182.25
188.31
194.35
200.40
206.46
212.52
218.58
224.64
230.69
236.75
242.81
273.10
345.81
460.99
576.17
691.36
57.60
62.00
69.00
75.00
81.50
87.50
93.60
99.80
105.50
111.50
118.00
124.20
129.70
136.00
141.80
149.00
153.90
160.00
165.90
172.30
178.00
184.10
190.50
196.30
203.30
209.30
214.60
221.00
226.80
232.90
239.80
245.10
251.30
282.50
354.00
469.90
585.10
700.60
Hub Length Stock

Hub Length Stock
Hub Length Stock
N
L
D
N
L
D
N
L
D
Tooth Width
B1 11.1mm
b1 10.8mm
B2 30.3mm
B3 49.8mm
31
37
42
46
52
58
64
70
75
80
80
80
80
90
90
90
90
90
95
95
95
95
95
95
95
95
95
95
100
100
100
100
100
100
100
100
100
100
Type A = Steel C45

Simplex (027D01--)
30
30
30
35
35
35
35
35
35
35
35
35
35
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
40
56
56
56
65
65
12
12
12
14
14
14
14
14
16
16
16
16
16
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
24
30
30
30
30
Triplex (027D03--)
Duplex (027D02--)
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
31
37
42
47
53
59
65
71
77
83
89
95
100
100
100
110
110
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
110
120
135
135
135
45
45
45
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
63
63
63
70
70
12
12
12
16
16
16
16
16
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
25
25
25
25
25
30
30
30
30
45
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
31
37
42
47
53
59
65
71
77
83
89
95
100
100
100
110
110
120
120
120
120
120
120
130
130
130
130
130
130
130
130
130
130
140
140
160
170
170
65
65
65
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
75
82
82
16
16
16
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
25
30
40
40
40
50
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
To complete the product code insert the number of teeth required (027D0109 = 12B-1 " pitch 9 tooth pilot bore sprocket)
16B PILOT BORED SPROCKETS 1" X 17.02mm PITCH

No. of
Teeth
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
45
57
76
95
114
Pitch
Dia
Outer
Dia
dp
de
66.37
74.27
82.19
90.14
93.14
106.12
114.15
122.17
130.20
138.22
146.28
154.33
162.38
170.43
178.48
186.53
194.59
202.66
210.72
218.79
226.85
234.92
243.00
251.08
259.13
267.21
275.28
283.36
291.44
299.51
307.59
315.67
323.75
364.13
461.08
614.65
768.22
921.81
77.00
85.00
93.00
99.50
109.00
117.00
125.00
133.00
141.00
149.00
157.00
165.20
173.20
181.20
189.30
197.50
205.50
213.50
221.60
229.60
237.70
245.80
254.00
262.00
270.00
278.50
287.00
296.20
304.60
312.60
320.70
328.80
336.90
377.00
474.00
627.00
781.10
935.60
Simplex (027E01--)
Triplex (027E03--)
Duplex (027E02--)
Hub Length Stock

Hub Length Stock
Hub Length Stock
N
L
D
N
L
D
N
L
D
42
50
55
61
69
78
84
92
100
100
100
100
100
110
110
110
110
110
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
125
125
140
140
140
35
35
35
40
40
40
40
40
14
45
45
45
45
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
70
70
80
80
80
16
16
16
16
16
16
16
16
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
25
30
35
35
40
40
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
42
50
56
64
72
80
88
96
104
112
120
128
130
130
130
130
130
130
130
130
130
130
130
140
140
140
140
140
140
140
140
140
140
150
170
175
175
175
65
65
65
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
70
75
90
95
95
95
16
16
16
20
20
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
40
40
40
45
45
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
42
50
56
64
72
80
88
96
104
112
120
128
130
130
130
130
130
130
130
130
130
130
130
140
140
140
140
140
140
140
140
140
140
160
180
200
200
200
95
95
95
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
110
110
115
20
20
20
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
45
45
45
50
50
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
Tooth Width
B1 16.2mm
b1 15.8mm
B2 47.7mm
B3 79.6mm
FINISHED BORES
N 1.5
Type A = Steel C45

To complete the product code insert the number of teeth required (027E0109 = 16B-1 1" pitch 9 tooth pilot bore sprocket)
25
Section : 2
chain drives

20B PILOT BORED SPROCKETS 1." X " PITCH
No. of
Teeth
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
57
76
de
Hub Length Stock

Hub Length Stock
Hub Length Stock
N
L
D
N
L
D
N
L
D
Tooth Width
B1 18.5mm
b1 18.2mm
B2 54.6mm
B3 91.0mm
98.10
108.00
117.90
127.80
137.80
147.80
157.80
167.90
177.90
187.90
198.00
208.10
218.10
228.20
238.30
248.30
258.40
268.50
278.60
288.60
298.70
308.80
318.90
329.00
339.10
349.20
359.30
369.40
379.50
389.50
399.60
409.70
419.80
591.50
783.50
53
63
70
77
88
98
108
118
120
120
120
120
120
140
140
140
140
140
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
135
140
Type A = Steel C45

Pitch
Dia
Outer
Dia
dp
82.96
92.84
102.74
112.68
122.68
132.65
142.68
152.72
162.75
172.78
182.85
192.91
202.98
213.04
223.11
233.17
243.23
253.33
263.40
273.49
283.56
293.65
303.75
313.85
323.91
334.01
344.10
354.20
364.30
374.39
384.49
394.59
404.69
576.35
768.32
Simplex (027F01--)
40
40
40
45
45
45
45
45
50
50
50
50
50
55
55
55
55
55
55
55
55
55
55
55
55
55
55
55
55
55
55
55
55
80
90
20
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
40
50
Triplex (027F03--)
Duplex (027F02--)
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
53
63
70
80
90
100
110
120
120
120
120
120
120
140
140
140
140
140
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
170
180
75
75
75
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
100
110
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
30
30
30
30
30
50
50
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
53
63
70
80
90
100
110
120
120
120
120
120
120
140
140
140
140
140
150
150
150
150
150
150
150
150
150
150
150
150
150
150
150
180
200
110
110
110
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
115
130
140
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
30
30
30
30
30
30
30
30
30
30
50
50
A
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
To complete the product code insert the number of teeth required (027F0109 = 20B-1 1." pitch 9 tooth pilot bore sprocket)
FINISHED BORES
N 1.5
26
chain drives
Section : 2
05B PLATEWHEEL 8 X 3mm PITCH
06B PLATEWHEEL
Tooth Width
B1 2.8mm
b1 2.7mm
B2 8.3mm
Tooth Width
B1
b1
B2
B3
(027J00-- for simplex)
No. of
Teeth
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
57
76
95
Pitch Dia
Outer Dia
Stock Bore
dp
de
Simp D1 Dup D2
20.90
23.39
25.89
28.39
30.91
33.42
35.95
38.48
41.01
43.53
46.07
48.61
51.14
53.68
56.21
58.75
61.29
63.83
66.37
68.91
71.45
73.99
76.53
79.08
81.61
84.16
86.70
89.25
91.79
94.33
96.88
99.42
101.97
104.51
107.05
109.60
112.14
114.69
117.23
119.77
122.32
145.22
193.59
241.96
MATERIAL: Steel grade C45
24.00
26.60
29.20
31.70
34.20
36.70
39.20
41.70
44.30
46.80
49.30
51.90
54.40
57.00
59.50
62.00
64.60
67.50
69.50
72.20
74.80
77.30
79.80
82.40
84.90
87.50
90.00
92.50
95.00
97.60
100.20
102.70
105.30
107.80
110.40
112.90
115.50
118.00
120.60
123.10
125.60
148.60
197.70
246.10
6
6
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
14
20
20
8
8
8
8
8
8
8
8
10
10
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
14
14
14
14
14
14
14
14
16
20
20
08B PLATEWHEEL " X 5/16" PITCH
/8" X 7/32" PITCH
(027A00-- for simplex)
No. of
Teeth
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
57
76
95
(027B00-- for simplex)

Tooth Width
B1
b1
B2
B3
5.3mm
5.2mm
15.4mm
25.6mm
Pitch Dia Outer Dia

dp
24.89
27.85
30.82
33.80
36.80
39.79
42.80
45.81
48.82
51.83
54.85
57.87
60.89
63.91
66.93
69.95
72.97
76.00
79.02
82.05
85.07
88.09
91.12
94.15
97.17
100.20
103.23
106.26
109.29
112.32
115.35
118.37
121.40
124.43
127.46
130.49
133.52
136.55
139.58
142.61
145.64
172.91
230.49
288.08
de
28.00
31.00
34.00
37.00
40.00
43.00
46.30
49.30
52.30
55.30
58.30
61.30
64.30
68.00
71.00
73.50
77.00
80.00
83.00
86.00
89.00
92.00
94.70
98.30
101.30
104.30
107.30
110.40
113.40
116.40
119.50
112.50
125.50
128.50
131.60
134.60
137.60
140.70
143.70
146.70
149.70
176.90
234.90
292.50
Stock Bore
Simp D1 Dup D2 Trip D3
6
7
7
8
8
8
8
8
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
16
16
16
16
16
16
16
16
16
20
20
8
8
8
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
14
14
14
14
14
14
14
14
14
14
16
16
16
16
16
16
16
16
16
20
20
8
8
10
10
10
10
12
12
12
12
12
12
12
14
14
14
14
14
14
14
14
14
14
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
20
25
25
No. of
Teeth
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
57
76
95
7.2mm
7.0mm
21.0mm
34.9mm
Pitch Dia Outer Dia

dp
33.18
37.13
41.10
45.07
49.07
53.06
57.07
61.09
65.10
69.11
73.14
77.16
81.19
85.22
89.24
93.27
97.29
101.33
105.36
109.40
113.42
117.46
121.50
125.54
129.56
133.60
137.64
141.68
145.72
149.76
153.80
157.83
161.87
165.91
169.95
173.99
178.03
182.07
186.10
190.14
194.18
230.54
307.33
384.11
de
37.20
41.00
45.20
48.70
53.00
57.40
61.80
65.50
69.50
73.60
77.80
81.70
85.80
89.70
93.80
98.20
101.80
105.80
110.00
114.00
118.00
122.00
126.10
130.20
134.30
138.40
142.60
146.70
151.00
154.60
158.60
162.70
166.80
171.40
175.40
179.70
183.80
188.00
192.10
196.20
200.30
236.40
313.30
390.10
Stock Bore
8
8
8
10
10
10
10
10
10
10
10
10
10
12
12
12
12
12
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
20
20
20
20
20
20
20
20
20
25
25
10
10
10
10
10
10
10
10
12
12
12
12
12
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
20
20
20
20
20
20
20
20
20
20
20
20
20
25
25
25
10
10
10
12
12
12
12
12
16
16
16
16
16
16
16
16
16
16
16
16
16
16
16
20
20
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
25
25
To complete the product code insert the number of teeth required (027B0009 = 08B-1 " pitch 9 tooth simplex platewheel)
27
Section : 2
chain drives
10B PLATEWHEEL
/8" X 3/8" PITCH
12B PLATEWHEEL " X 7/16" PITCH
(027C00-- for simplex)

Tooth Width
B1
b1
B2
B3
No. of
Teeth
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
57
76
95
Tooth Width
B1
b1
B2
B3
9.1mm
9.0mm
25.5mm
42.1mm
Pitch Dia Outer Dia

dp
41.48
46.42
51.37
56.34
61.34
66.32
71.34
76.36
81.37
86.39
91.42
96.45
101.49
106.52
111.55
116.58
121.62
126.66
131.70
136.75
141.78
146.83
151.87
156.92
161.95
167.00
172.05
177.10
182.15
187.20
192.24
197.29
202.34
207.39
212.44
217.49
222.53
227.58
232.63
237.68
242.73
288.18
384.16
480.14
de
47.00
52.60
57.50
63.00
68.00
73.00
78.00
83.00
88.00
93.00
98.30
103.30
108.40
113.40
118.00
123.40
128.30
134.00
139.00
144.00
148.70
153.80
158.80
163.90
168.90
174.50
179.00
184.10
189.10
194.20
199.20
204.20
209.30
214.80
219.90
224.90
230.00
235.00
240.10
245.10
250.20
296.00
392.10
488.50
(027E00-- for Simplex)
Stock Bore
10
10
10
10
10
10
10
10
12
12
12
12
12
12
12
12
12
12
16
16
16
16
16
16
16
16
16
16
20
20
20
20
20
20
20
20
20
20
20
20
20
25
25
30
10
10
10
10
10
10
10
12
12
12
12
12
12
16
16
16
16
16
16
16
16
16
16
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
25
25
25
25
25
30
12
12
12
12
12
12
12
12
16
16
16
16
16
16
16
16
16
16
20
20
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
25
25
25
25
25
30
30
No. of
Teeth
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
57
76
95
Tooth Width
B1
b1
B2
B3
11.1mm
10.8mm
30.3mm
49.8mm
Pitch Dia Outer Dia

dp
49.78
55.70
61.64
67.61
73.61
79.59
85.61
91.63
97.65
103.67
109.71
115.75
121.78
127.82
133.86
139.90
145.94
152.00
158.04
164.09
170.13
176.19
182.25
188.31
194.35
200.40
206.46
212.52
218.58
224.64
230.69
236.75
242.81
248.87
254.93
260.98
267.04
273.10
279.16
285.21
291.27
345.81
460.99
576.17
de
57.60
62.00
69.00
75.00
81.50
87.50
93.60
99.80
105.50
111.50
118.00
124.20
129.70
136.00
141.80
149.00
153.90
160.00
165.90
172.30
178.00
184.10
190.50
196.30
203.30
209.30
214.60
221.00
226.80
232.90
239.00
245.10
251.30
257.30
264.50
270.50
276.50
282.50
287.90
294.00
300.10
355.40
469.90
585.10
Stock Bore
12
12
12
14
14
14
14
14
14
14
14
14
14
16
16
16
16
16
16
16
16
16
16
20
20
20
20
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
30
30
12
12
12
14
14
14
14
14
16
16
16
16
16
16
16
16
16
16
20
20
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
25
25
25
25
25
30
30
12
12
12
16
16
16
16
16
16
16
16
16
16
20
20
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
30
30
30
No. of
Teeth
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
57
76
95
To complete the product code insert the number of teeth required (027C0009 = 10B-1 5/8" pitch 9 tooth simplex platewheel)
NOTE: Platewheels for use with friction torque limiting devices may require a special surface finish.
28
16B PLATEWHEEL 1" X 17.02mmPITCH
(027D00-- for Simplex)
16.2mm
15.8mm
47.7mm
79.6mm
Pitch Dia Outer Dia

dp
66.37
74.27
82.19
90.14
98.14
106.12
114.15
122.17
130.20
138.22
146.28
154.33
162.38
170.43
178.48
186.53
194.59
202.66
210.72
218.79
226.85
234.92
243.00
251.08
259.13
267.21
275.28
283.36
291.44
299.51
307.59
315.67
323.75
331.82
339.90
347.98
356.06
364.13
372.21
380.29
388.36
461.07
614.65
768.22
de
77.00
85.00
93.00
99.50
109.00
117.00
125.00
133.00
141.00
149.00
157.00
165.20
173.20
181.20
189.30
197.50
205.50
213.50
221.60
229.60
237.70
245.80
254.00
262.00
270.00
278.50
287.00
296.20
304.60
312.60
320.70
328.80
336.90
345.00
353.00
361.10
369.10
377.10
385.20
393.20
401.30
474.00
627.00
781.10
Stock Bore
Simp D1 Dup D2 TripD3
14
14
15
15
15
15
15
15
19
19
19
19
19
20
20
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
30
30
30
16
16
16
20
20
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
30
30
30
16
16
16
20
20
20
20
20
25
25
25
25
25
25
25
25
25
25
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
40
40
40
chain drives
Section : 2
20B PLATEWHEEL 1." X " PITCH
(027F00-- for Simplex)
Tooth Width
B1
b1
B2
B3
No. of
Teeth
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
57
76
95
18.5mm
18.2mm
54.6mm
91.0mm
Pitch Dia Outer Dia

dp
82.96
92.84
102.74
112.68
122.68
132.65
142.68
152.72
162.75
172.78
182.85
192.91
202.98
213.04
223.11
233.17
243.23
253.33
263.40
273.49
283.56
293.65
303.75
313.85
323.91
334.01
344.10
354.20
364.30
374.39
384.49
394.59
404.69
414.77
424.86
434.96
445.06
455.17
465.25
475.35
485.45
576.35
768.32
960.25
de
98.10
108.00
117.90
127.80
137.80
147.80
157.80
167.90
177.90
187.90
198.00
208.10
218.10
228.20
238.30
248.30
258.40
268.50
278.60
288.60
298.70
308.80
318.90
329.00
339.10
349.20
359.30
369.40
379.50
389.50
399.60
409.70
419.80
429.90
440.00
450.10
460.20
470.30
480.40
490.50
500.60
591.50
783.50
975.20
Stock Bore
16
16
16
16
20
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
30
30
30
30
30
30
30
30
30
30
30
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
20
20
20
20
20
20
20
20
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
30
30
30
30
30
30
30
30
30
30
30
40
40
40
40
40
40
40
40
40
40

To complete the product code insert the number of teeth
required (027C0009 = 20B-1 1." pitch 9 tooth simplex
platewheel)
NOTE: Platewheels for use with friction torque limiting devices may require a special surface finish.
29
Section : 2
chain drives
Installation and Maintenance

INSTALLATION NOTES
CHAIN TENSION
Shafts must be parallel. Supporting structures must

be of sufficient rigidity to maintain true alignment.
Chains should be fairly tight at installation with only

a small amount of slack. With vertical drives the
chain should be kept snug. After the first few weeks
of operation, re-check chain tension and adjust if
necessary.
Mount sprockets as close as possible to bearings.

Check correct alignment of each sprocket by
use of a straight edge.
Roller chain can be used in practically any position
provided the shafts are parallel.
Where the slack strand is nearly vertical, or where
torque variation causes waves or whip in the chain,
an idler must be used to take up the excessive slack.
The idler should preferably be near to the larger
sprocket in the drive, located on the outside of the
slack strand of the chain. Where layout makes this
impossible it is permissible to locate the idler on the
inside of the chain.
Chain Tensioners
FIXED CENTRE APPLICATIONS

An idler sprocket is generally recommended for fixed
centre drives. It should be positioned on the slack
side as close to the larger sprocket as feasible. The
tensioning sprocket should have a minimum of three
teeth engaged and be a minimum of four links away
from the nearest sprocket.
Reversible
Drives
Multi Sprocket
Drives
Chain
Engagement
Lubrication
Effective lubrication is essential in order to ensure
optimum wear life from any chain.
To be effective it must form a film of lubricant
between the wearing parts, (the pin and bush), of the
chain. It has therefore to be of suitable viscosity and
be delivered to the gap between the sideplates such
that it can penetrate into the space between the pin
and bush. The viscosity, amount and type of lubricant
is governed by the size of chain and the operating
conditions involved. Oil will only penetrate into the
bearing area of the chain when the chain is slack,
therefore oil should be delivered to the slack strand
just after the driver sprocket.
High speed drives are especially critical. These
generally require a continuous stream of lubricant
applied across the full chain width in order to act as
a coolant as well as lubricating the bearing area.
Three basic lubrication methods are recommended
for use with Fenner roller chain.
Type 1
Drip Feed (for linear chain speeds

up to 1 m/sec.)
Oil drops directed between the side plate gaps with

a drip feed lubricator. Brush applicators may also be
used, provided they are positioned to ensure that the
oil is correctly delivered to the gap between the side
plates. Volume and frequency should be sufficient to
prevent discolouration of the lubricant in the chain
joints. Any discolouration of the lubricant or of the
pin will indicate insufficient lubrication penetrating
into the bearing area. Air movement, due to the
motion of the drive, can disturb and mis-direct the oil
drops, therefore, with due regard for safety, check
the applicator while the drive is running.
30
Vertical
Positioning
Normal
Positioning
Type 2 Oil Bath or Disc Lubricator (for

linear chain speeds up to 6 m/sec.)
With oil bath lubrication the lower strand of chain
runs through an oil sump. With the chain running,
the oil level in the sump should immerse the chain at
its lowest point. The oil level and condition of the oil
should be checked periodically to ensure sufficient
volume of oil is present and that it has not emulsified
or become contaminated.
Chain Lubrication
Link
Plates
Clearances for
Lubricant
A disc or oil slinger may also be used. In which case

the disc picks up oil from the sump and deposits it
on the chain, usually through a trough. The chain
operates above the oil level. The diameter of the
disc should be sufficient to ensure a rim speed
between 3 and 15 m/s.
Type 3
Pump and Sump (for high speed

drives).
Oil is pumped from the sump by a circulating pump

capable of delivering a constant stream of oil, evenly
distributed across the full width of the chain. The
oil should be supplied on the inside of the chain loop
and at the lower strand, when chain speeds exceed
10 m/s.
Bush
Roller
Pin
chain drives
Section : 2
Taper Lock Installation Instructions

TO INSTALL
1.
After ensuring that the mating tapered

surfaces, bore and shaft, are completely clean
and free from oil or dirt, insert the bush into the
hub so that holes line up.
2.
Sparingly oil thread and point of grub screws,

or thread and under head of cap screws. Place
screws loosely in holes threaded in hub, shown
thus in diagram.
3.
If a key is to be fitted, place it in the shaft

keyway before fitting the bush. It is essential
that it is a parallel key and side fitting only and
has TOP CLEARANCE.
4.
Clean shaft and fit hub to shaft as one unit and

locate in position desired, remembering that
bush will nip the shaft first and then hub will
be slightly drawn on to the brush.
5.
Using a hexagon wrench tighten screws

gradually and alternately to torque shown in
table below.
6.
Hammer against large-end of bush, using a

block or sleeve to prevent damage. (This will
ensure that the bush is seated squarely in
the bore.) Screws will now turn a little more.
Repeat this alternate hammering and screw
tightening once or twice to achieve maximum
grip on the shaft.
7.
After drive has been running under load for a

short time stop and check tightness of screws.
8.
Fill empty holes with grease to exclude dirt.
INSERT BUSH
INSERT SCREWS AND LOCATE ON SHAFT
TIGHTEN SCREWS FINGER TIGHT
TIGHTEN SCREWS ALTERNATELY
TIGHTEN SCREWS TO THE CORRECT TORQUE

SETTING
REMOVING A TAPER LOCK BUSH
TO REMOVE
1.
Slacken all screws by several turns, remove

one or two according to number of removal
holes shown thus
in diagram. Insert
screws into removal holes after oiling thread
and under head of cap screws.
2.
Tighten screws alternately until bush is

loosened in hub and assembly is free on the
shaft.
3.
Remove assembly from shaft.
REMOVAL HOLES
Bush Size
1008
1108
1210
1610
1615
2012
2517
3020
3030
3525
3535
4030
4040
4535
4545
5040
5050
Screw tightening
torque (Nm)
5.6
5.6
20.0
20.0
20.0
30.0
50.0
90.0
90.0
115.0
115.0
170.0
170.0
190.0
190.0
270.0
270.0
Qty
Size (BSW)
1/4"
1/4"
3/8"
3/8"
3/8"
7/16"
1/2"
5/8"
5/8"
1/2"
1/2"
5/8"
5/8"
3/4"
3/4"
7/8"
7/8"
Hex Socket
size (mm)
10
10
12
12
14
14
14
14
Large end diameter

(mm)
35.0
38.0
47.5
57.0
57.0
70.0
85.5
108.6
108.0
127.0
127.0
146.0
146.0
162.0
162.0
178.0
178.0
Bush Length (mm)
22.3
22.3
25.4
25.4
38.1
31.8
44.5
50.8
76.2
63.5
89.0
76.2
102.0
89.0
114.0
102.0
127.0
Approx mass (kg)
0.1
0.1
0.2
0.3
0.5
0.7
1.5
2.7
3.6
3.8
5.0
5.6
7.7
7.5
10.0
11.1
14.0
Screw
details
31
Section : 2
chain drives
Accessories
CHAIN PULLERS
PIN EXTRACTORS
For drawing ends of a chain length together, to allow

insertion of connecting links.
Splitting chain to required length is simple with this

easy to use tool. The pin extractor may be used with
almost any size and make of roller chain.
Catalogue Code
Catalogue
Code
028Z0035
Model
35
028Z0001
5 8
028Z0002
1"
028Z0003
2"
FREEWHEEL
SizeUNITS
/"
Bore
Catalogue Code
Chain
sizes
Jaw
Spread
Weight
/8""
50mm
0.14 kg
RSJ
13/8"
2"
027Z0000
13/8"
13/8"
027Z0019
5/
8"
027Z0022
2"
027Z0024
028Z0050
50
"1"
85mm
0.45 kg
NVF
028Z0080
80
1"3"
125mm
0.90 kg
" x 5/16" x 19T

" x 5/16" x 19T
" x
" x 19T
3/
16
" x 3/16" x 19T
32
Max Pitch
027Z0001
027Z0020

679 02 Fenner Chain Drives

Uploaded by

Copyright:

Available Formats

679 02 Fenner Chain Drives

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

679 02 Fenner Chain Drives

Uploaded by

Copyright:

Available Formats

What are the different types of chain drives discussed?

What are the different types of chain drives discussed?

What factors need to be considered when selecting a chain drive?

What factors need to be considered when selecting a chain drive?

CHAIN DRIVES

BS and ANSI transmission roller chains up to

A comprehensive range of Fenner Taper

Stainless steel and 'lube-free' variants also

Type of prime mover, or driving machine

Roller Chain Drive Selection

Electric motor starting arrangement

Rotational speed of prime mover

Power rating of prime mover

Double Pitch Chain

Type of driven machine

Double Pitch Conveyor Chain

Rotational speed of driven machine

Special & Attachment Chain

Power absorbed by driven machine

Hours/day duty & start/stop frequency

Both driven & driver machine shaft diameters

Taper Lock Sprokets

Centre distance & space restraints:

> fixed centres?

Pilot Bore Sprockets

Any environmental issues:

> ambient temperature

Installation & Maintenance

Fenner Advanced Chain Technology

> Built-in lubrication

The Mark of Engineering Excellence

Chain Drive Selection

TABLE 1 SERVICE FACTORS

Types of Prime Mover

From Table 1, determine the service factor which is

(b) Design Power

(c) Chain Pitch

Hours per day duty

(d) Speed Ratio

Divide the speed of the faster shaft by the speed of the

Agitators (uniform density),

(e) Sprocket Sizes

(f) Power Rating

(g) Chain Length

To find the Chain length in pitches, use the formula below.

Length of chain in feet =

Select a chain drive to transmit 1.5 kW from a gearbox

(a) Service Factor

From Table 1 the Service Factor is 1.2.

Recommended centre distance for 16B-1 chain is 1000

(b) Design Power

(c) Chain Pitch

From Table 4 (page 6) sprockets of 19 and 38 teeth give

108 pitches or 9 feet of Fenner 16B-1 chain

(f) Power Rating

Alternative Drive Specification

(d) Speed Ratio

(e) Sprocket Size

124 pitches or 7.75 feet of Fenner 12B-2 chain

TABLE 5 - RECOMMENDED CENTRE DISTANCE