Anritsu Ethernet Tester PDF

Network Master Series
MT9090A
Mainframe
MU909060A Series
Gigabit Ethernet Module
Operation Manual
Fifth Edition
For safety and warning information, please read this

manual before attempting to use the equipment.
Keep this manual with the equipment.
ANRITSU CORPORATION
Document No.: M-W3166AE-5.0
Safety Symbols
To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the
following safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of
the symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu
equipment. In addition, there may be other labels attached to products that are not shown in the diagrams in this
manual.
Symbols used in manual
DANGER
This indicates a very dangerous procedure that could result in serious injury or
death if not performed properly.
WARNING
This indicates a hazardous procedure that could result in serious injury or death if
not performed properly.
CAUTION
This indicates a hazardous procedure or danger that could result in light-to-severe

injury, or loss related to equipment malfunction, if proper precautions are not taken.
Safety Symbols Used on Equipment and in Manual

The following safety symbols are used inside or on the equipment near operation locations to provide information
about safety items and operation precautions. . Ensure that you clearly understand the meanings of the symbols
and take the necessary precautions BEFORE using the equipment.
This indicates a prohibited operation. The prohibited operation is indicated
symbolically in or near the barred circle.
This indicates an obligatory safety precaution. The obligatory operation is
indicated symbolically in or near the circle.
This indicates a warning or caution. The contents are indicated symbolically in or
near the triangle.
This indicates a note. The contents are described in the box.
These indicate that the marked part should be recycled.
Network Master Series

MT9090A Mainframe
MU909060A Series Gigabit Ethernet Module
Operation Manual
24 March
2009 (First Edition)
24 March
2010 (Fifth Edition)
Copyright 2009-2010, ANRITSU CORPORATION.
All rights reserved. No part of this manual may be reproduced without the prior written permission of the
publisher.
The contents of this manual may be changed without prior notice.
Printed in Japan
ii
For Safety
WARNING
1. ALWAYS refer to the operation manual when working near locations
at which the alert mark shown on the left is attached. If the advice in
the operation manual is not followed there is a risk of personal injury
or reduced equipment performance. The alert mark shown on the left
may also be used with other marks and descriptions to indicate other
dangers.
2. IEC 61010 Standard
The IEC 61010 standard specifies four categories to ensure that an
instrument is used only at locations where it is safe to make
measurements. This instrument is designed for measurement
category I (CAT I). DO NOT use this instrument at locations specified
as category II, III, or IV as defined below.
Measurement category I (CAT I):
Secondary circuits of a device that is not directly connected to a
power outlet.
Measurement category II (CAT II):
Primary circuits of a device that is directly connected to a power
outlet, e.g., portable tools or home appliance.
Measurement category III (CAT III):
Primary circuits of a device (fixed equipment) to which power is
supplied directly from the distribution panel, and circuits running from
the distribution panel to power outlet.
Measurement category IV (CAT IV):
Building service-line entrance circuits, and circuits running from the
service-line entrance to the meter or primary circuit breaker
(distribution panel).
iii
For Safety
WARNING
3. Laser radiation warning
NEVER look directly into the cable connector on the equipment
nor into the end of a cable connected to the equipment. There is a
risk of injury if laser radiation enters the eye.
The Laser Safety label is attached to the equipment for safety use
as indicated in "Laser Safety" later in this section.
Repair
4. This equipment cannot be repaired by the operator. DO NOT attempt

to remove the equipment covers or unit covers or to disassemble
internal components. Only qualified service personnel with knowledge
of electrical fire and shock hazards should service this equipment.
There are high-voltage parts in this equipment presenting a risk of
severe injury or fatal electric shock to untrained personnel. In addition,
there is a risk of damage to precision components.
Calibration
5. The performance-guarantee seal verifies the integrity of the equipment.

To ensure the continued integrity of the equipment, only Anritsu
service personnel, or service personnel of an Anritsu sales
representative, should break this seal to repair or calibrate the
equipment. If the performance-guarantee seal is broken by you or a
third party, the performance of the equipment cannot be guaranteed.
Be careful not to break the seal by opening the equipment or unit
covers.
6. This equipment should always be positioned in the correct manner. If
the cabinet is turned on its side, etc., it will be unstable and may be
damaged if it falls over as a result of receiving a slight mechanical
shock.
Always set up the equipment in a position where the power switch
can be reached without difficulty.
Falling Over
iv
For Safety
WARNING
Replacing Battery
7. When replacing the battery, use the specified battery and insert it
with the correct polarity. If the wrong battery is used, or if the battery
is inserted with reversed polarity, there is a risk of explosion causing
severe injury or death.
Battery Fluid
8. DO NOT short the battery terminals and never attempt to disassemble

the battery or dispose of it in a fire. If the battery is damaged by any of
these actions, the battery fluid may leak. This fluid is poisonous.
DO NOT touch the battery fluid, ingest it, or get in your eyes. If it is
accidentally ingested, spit it out immediately, rinse your mouth with
water and seek medical help. If it enters your eyes accidentally, do
not rub your eyes, rinse them with clean running water and seek
medical help. If the liquid gets on your skin or clothes, wash it off
carefully and thoroughly.
LCD
9. This instrument uses a Liquid Crystal Display (LCD). DO NOT subject

the instrument to excessive force or drop it. If the LCD is subjected to
strong mechanical shock, it may break and liquid may leak.
This liquid is very caustic and poisonous.
DO NOT touch it, ingest it, or get in your eyes. If it is ingested
accidentally, spit it out immediately, rinse your mouth with water and
seek medical help. If it enters your eyes accidentally, do not rub your
eyes, rinse them with clean running water and seek medical help. If
the liquid gets on your skin or clothes, wash it off carefully and
thoroughly.
For Safety
CAUTION
Check Terminal
1. Never input a signal of more than the indicated value between the
measured terminal and ground. Input of an excessive signal may
damage the equipment.
vi
For Safety
Class 1, 1M, 2, 2M, 3R, 3B and 4 indicate the danger degree of the
laser radiation specified below according to IEC 60825-1:2001.
Class 1:
Lasers that are safe under reasonably foreseeable conditions

of operation, including the use of optical instruments for
intrabeam viewing.
Class 1M: Lasers emitting in the wavelength range from 302.5 to 4000
nm that are safe under reasonably foreseeable conditions of
operation, but may be hazardous if the user employs optics
within the beam. Two conditions apply:
a) for diverging beams, if the user views the laser output with
certain optical instruments (for example, eye loupes,
magnifiers and microscopes) within a distance of 100 mm;
or
b) for collimated beams, if the user views the laser output
with certain optical instruments (for example, telescopes
and binoculars).
Class 2, 2M, 3R, 3B and 4 does not apply.
CAUTION
Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
The use of optical instruments with this product will increase eye
hazard.
vii
For Safety
WARNING
Laser Safety
The laser in the plug-in unit provided for this equipment is classified as
Class 1 according to the IEC 60825-1:2001 standard.
Table 1 Laser Safety Classifications Based on IEC 60825-1:2001

SFP Type
viii
Class
Class 1 AEL (W)
Pulse Width (s)/

Nominal
Laser Aperture
Repetition Rate Wavelength (nm)
LX and FX
0.0156
CW
1310
Figure 1,
1 or 2
ZX
0.01
CW
1550
Figure 1,
1 or 2
SX
0.000709
CW
850
Figure 1,
1 or 2
For Safety
Table 3 Indication Labels on Product (Ex: Label list)
Type
Sample
Affixed to:
Model Name
Explanation
Figure 1, C
All
Certification
Figure 1, B
All
Identification
Figure 1, A
All
Warning
Figure 1, D
All
ix
For Safety
Laser Radiation Markings
1 2
A
B
C D
Figure 1 Locations of Laser Beam Apertures and Affixed Labels
For Safety
FOR EU & EFTA CUSTOMERS
Please Recycle.
Ni-MH
Read the following when using products to which the mark shown on the
above is attached.
The product that you have purchased contains a rechargeable battery.
The battery is recyclable. At the end of its useful life, under various state
and local laws, it may be illegal to dispose of this battery into the
municipal waste. Check with your local solid-waste disposal officials for
details of recycling options or proper disposal in your area.
Before disposing of this product, discharge the battery and mail it to
your Anritsu Service or Sales office.
1. Disconnect the AC adapter, if used.
2. Turn the power switch to on.
3. Leave the product on until the power indicator goes off; the battery is
now discharged.
4. Remove the battery.
5. Insulate the battery terminals with adhesive tape.
6. Please recycle in accordance with your national or regional
legislation.
Nach gebrauch der Verkaufsstelle zurckgeben.
Aprs usage rapporter au point de vente.
xi
For Safety
CAUTION
External
Storage Media
This equipment uses USB flash drives as external storage media for
storing data and programs.
If this media is mishandled or becomes faulty, important data may be
lost. To prevent this chance occurrence, all important data and
programs should be backed-up.
Anritsu will not be held responsible for lost data.
Pay careful attention to the following points.
Never remove the USB flash drive from the instrument while it is
being accessed.
The USB flash drive may be damaged by static electric charges.
xii
For Safety
CAUTION
Use in a residential
environment
This instrument is designed for an industrial environment.

In a residential environment this instrument may cause radio
interference in which case the user may be required to take adequate
measures.
xiii
Equipment Certificate
Anritsu Corporation certifies that this equipment was tested before shipment
using calibrated measuring instruments with direct traceability to public
testing organizations recognized by national research laboratories, including
the National Institute of Advanced Industrial Science and Technology, and
the National Institute of Information and Communications Technology, and
was found to meet the published specifications.
Anritsu Warranty
Anritsu Corporation will repair this equipment free-of-charge if a malfunction
occurs within one year after shipment due to a manufacturing fault, under the
condition that this warranty is void when:
The fault is outside the scope of the warranty conditions described in the
operation manual.
The fault is due to mishandling, misuse, or unauthorized modification or
repair of the equipment by the customer.
The fault is due to severe usage clearly exceeding normal usage.
The fault is due to improper or insufficient maintenance by the customer.
The fault is due to natural disaster including fire, flooding, earthquake,
etc.
The fault is due to use of non-specified peripheral equipment, peripheral
parts, consumables, etc.
The fault is due to use of a non-specified power supply or in a
non-specified installation location.
In addition, this warranty is valid only for the original equipment purchaser. It
is not transferable if the equipment is resold.
Anritsu Corporation shall assume no liability for injury or financial loss of the
customer due to the use of or a failure to be able to use this equipment.
Anritsu Corporation Contact

In the event that this equipment malfunctions, contact an Anritsu Service and
Sales office. Contact information can be found on the last page of the printed
version of this manual, and is available in a separate file on the CD version.
xiv
Notes On Export Management

This product and its manuals may require an Export License/Approval by
the Government of the product's country of origin for re-export from your
country.
Before re-exporting the product or manuals, please contact us to confirm
whether they are export-controlled items or not.
When you dispose of export-controlled items, the products/manuals need
to be broken/shredded so as not to be unlawfully used for military purpose.
Reuse parts
Anritsu group promotes recycling activities in order to reuse available
resources and save energy. This product may use recycled parts
(mechanical components) that conform to Anritsus quality standards.
xv
FOR CALIFORNIA USA ONLY

This product contains a CR Coin Lithium Battery which contains
Perchlorate Material special handling may apply; See
www.dtsc.ca.gov/hazardouswaste/perchlorate
xvi
Crossed-out Wheeled Bin Symbol

Equipment marked with the Crossed-out Wheeled Bin Symbol complies with
council directive 2002/96/EC (the WEEE Directive) in European Union.
For Products placed on the EU market after August 13, 2005, please contact
your local Anritsu representative at the end of the product's useful life to
arrange disposal in accordance with your initial contract and the local law.
xvii
Notice
The following actions are strictly prohibited for all of the software installed
in this product or otherwise provided by Anritsu:
1. Copying, except for archival purposes.
2. Transferring to a third party separately from this product.
3. Analyzing the incorporated software including but not limited to
modifying, decompiling, disassembling, and reverse engineering.
Cautions against computer virus infection

Copying files and data
Only files that have been provided directly from Anritsu or generated
using Anritsu equipment should be copied to the instrument.
All other required files should be transferred by means of USB or
CompactFlash media after undergoing a thorough virus check.
Adding software
Do not download or install software that has not been specifically
recommended or licensed by Anritsu.
Network connections
Ensure that the network has sufficient anti-virus security protection in
place.
xviii
CE Conformity Marking
Anritsu affixes the CE conformity marking on the following product(s) in
accordance with the Council Directive 93/68/EEC to indicate that they
conform to the EMC directive of the European Union (EU).
CE marking
1. Product Model
Model:
MT9090A Mainframe
MU909060A1 Gigabit Ethernet Module RJ45 SFP
MU909060A2 Gigabit Ethernet Module RJ45 RJ45
MU909060A3 Gigabit Ethernet Module SFP SFP
2. Applied Directive
EMC:
Directive 2004/108/EC
3. Applied Standards
EMC: EN 300 386 TC and OTC
IEC 61000-4-2 (ESD)
IEC 61000-4-3 (EMF)
IEC 61000-4-4 (Burst)
IEC 61000-4-5 (Surge)
IEC 61000-4-6 (CRF)
Performance Criteria*
B
A
B
B
A
*: Performance Criteria
A: During testing, normal performance within the
specification limits.
B: During testing, temporary degradation, or loss of
function or performance which is self-recovering.
C: During testing, temporary degradation, or loss of
function or performance which requires operator
intervention or system reset occurs.
Harmonic current emissions:
EN 61000-3-2: 2006 (Class A equipment)
: No limits apply for this equipment with an active input
power under 75 W.
xix
C-Tick Conformity Marking

Anritsu affixes the C-Tick mark on the following product(s) in accordance
with the regulation to indicate that they conform to the EMC framework of
Australia/New Zealand.
C-Tick mark
1. Product Model
Model:
MT9090A Mainframe
MU909060A1 Gigabit Ethernet Module RJ45 SFP
MU909060A2 Gigabit Ethernet Module RJ45 RJ45
MU909060A3 Gigabit Ethernet Module SFP SFP
2. Applied Standards
EMC: Emission:
xx
EN 55 022, Class B
About This Manual

The purpose of this operation manual is to explain how to set up the
MU909060A Series Gigabit Ethernet Module and how to use the various
features and modes. This manual is designed to appeal to professionals
with the technical background to use this type of instrument.
Descriptions in this manual assume a knowledge of Ethernet and IP
technology.
Table of Contents
For Safety ....................................................
iii
About This Manual........................................
Chapter 1 Overview....................................
1-1
1.1
1.2
1.3
1.4
1.5
1.6
1.7
Configuration.................................................................
Front Panel ...................................................................
Back Panel....................................................................
Bottom Panel ................................................................
Top Connector Panel ....................................................
Changing Test Module..................................................
Basic Usage Notes .......................................................
1-2
1-4
1-8
1-13
1-14
1-27
1-29
Chapter 2 General Operation ....................
2-1
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
Power Up/Power Down.................................................

General Functions.........................................................
Mass Storage................................................................
Print Screen ..................................................................
Status Screen ...............................................................
Result Screens..............................................................
Save and Load..............................................................
Setup.............................................................................
PDF Reports .................................................................
2-3
2-5
2-11
2-16
2-17
2-22
2-26
2-29
2-30
Chapter 3 Ethernet Application.................
3-1
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
II
Application Ethernet Status ..........................................

Application Ethernet Setup ...........................................
Generator Test..............................................................
BER Test.......................................................................
Stimuli ...........................................................................
Ping Test.......................................................................
Cable Test.....................................................................
RFC2544 Tests.............................................................
3-2
3-3
3-23
3-30
3-32
3-36
3-39
3-41
1
Chapter 4 Application Reflector................
4.1
4.1
4.2
4.3
Status ............................................................................
Status ............................................................................
Setup Interface..............................................................
Result ............................................................................
4-1
4-2
4-2
4-3
4-7
2
3
Chapter 5 Pass Through............................

5.1
5.1
5.2
5.3
5.4
5-1
Status ............................................................................
Status ............................................................................
Setup Interface..............................................................
Testing ..........................................................................
Result ............................................................................
5-2
5-2
5-3
5-5
5-6
Chapter 6 Updating Firmware ...................
6-1
6.1
Updating Firmware........................................................
6-2
Chapter 7 Service Information ..................
7-1
7.1
7.2
7-2
7-6
Appendix A Specifications .........................
A-1
A.1
A.2
A-1
A-6
Appendix B Software Licenses ..................
B-1
B.1
Software Licenses.........................................................
6
7
Index
Specifications................................................................
Parts and Accessories ..................................................
Appendix
Self Diagnostics ............................................................

Maintenance .................................................................
B-2
Index .......................................................... Index-1
III
IV.
Chapter 1 Overview
It is important to know the layout, use, and functions of the front panel,
back panel, and top connector panel of the Network Master.
1.2
1.3
1.4
1.5
1.6
1.7
Configuration..............................................................
1.1.1 Standard Configuration .................................
1.1.2 Option ............................................................
Front Panel ................................................................
1.2.1 LCD................................................................
1.2.2 Panel Keys ....................................................
Back Panel.................................................................
1.3.1 Power and Batteries ......................................
1.3.2 Installing Ni-MH Battery Pack........................
1.3.3 Battery Replacement
Ni-MH Pack To AA Ni-MH .............................
Bottom Panel .............................................................
Top Connector Panel.................................................
1.5.1 AC Charger/Adapter ......................................
1.5.2 Battery Status LED ........................................
1.5.3 RJ45 Port.......................................................
1.5.4 SFP Port ........................................................
1.5.5 Connecting Peripheral Devices .....................
1.5.6 Cautions on Handling Optical Fiber Cables ..
Changing Test Module...............................................
Basic Usage Notes ....................................................
Overview
1.1
1-2
1-2
1-3
1-4
1-5
1-6
1-8
1-9
1-10
1-12
1-13
1-14
1-15
1-18
1-19
1-20
1-22
1-25
1-27
1-29
1-1
Chapter 1 Overview
1.1 Configuration
1.1.1
7B
Standard Configuration
The table below lists the standard configuration of the Network Master
series Gigabit Ethernet Module.
If you find any missing or broken components, immediately contact
Anritsu or our sales dealer.
Table 1.1.1-1 Standard configuration

Item
Model or
order No.
Qty.
Body
Module
MT9090A
MU909060A1
Mainframe
1
1*
Accessary
MU909060A2
MU909060A3
W3173AE

Quick guide
Network Master Gigabit
Ethernet Tester CD
AC charger/adapter
Ni-MH battery pack
Strap
1*
1*
1
Z1234A
G0203A
G0202A
Z1023A
*:Exclusive
1-2
Name
1
1
1
1
Remarks
One RJ-45,One
SFP
Two RJ-45
Two SFP
1.1
1.1.2
8B
Configuration
Option
Below Options are available for Gigabit Ethernet Module.

Table 1.1.2-1 Option
MU909060A1-001
MU909060A1-002
MU909060A2-001
MU909060A2-002
MU909060A3-001
MU909060A3-002
Name
RFC2544 test
Multistream
RFC2544 test
Multistream
RFC2544 test
Multistream
Overview
Model
Remark
Software Option
Software Option
Software Option
Software Option
Software Option
Software Option
RFC2544 test
This option enables RFC 2544 testing described in Section 3.8 RFC 2544
test.
Multistream
This option generates Multistream described in Section 3.3 Generator
Test.
1-3
Chapter 1 Overview
1.2 Front Panel

The front panel contains the operation controls and LCD display.
Figure 1.2-1 Front Panel Layout
LCD
Soft keys
Start key
Arrow keys and Set key
Menu/Power key
1-4
1.2
1.2.1
9B
Front Panel
LCD
The graphical user interface varies with the selected mode but each
screen shares common elements as shown in the figure below.
Overview
Screen title
Displays title of current screen
Time display
Battery or plug
icon
Presentation field
Displays current time in 24-hour format

(hh:mm:ss)
Shows unit connected to external power
supply (plug icon) or operating on battery
power (battery icon) with graphic
illustrating remaining charge
Changes with screen display
Soft keys
Display on-screen details
1-5
Chapter 1 Overview
1.2.2
10B
Panel Keys
Soft keys
The unit has four soft keys (F1 thru F4) on the
right hand side of the LCD. The function of each
key is determined by the current operation mode
and is displayed on the screen to the left of the
key.
Start key
Press to start the test.
1-6
1.2
Front Panel
Arrow keys and Set key
The arrow keys (Left/Right/Up/Down) have the

following functions:
Moves cursor/highlight to left
Moves cursor/highlight to right
Moves cursor/highlight up
Moves cursor/highlight down
Selects highlighted item
Menu/Power key
When unit is off:
Press the Menu/Power key to power up.
When unit is on:
Press the Menu/Power key to display the
pop-up menu.
Power Down can be selected from the
pop-up menu.
1-7
Overview
Left arrow key

Right arrow key
Up arrow key
Down arrow key
Set key
Chapter 1 Overview
1.3 Back Panel

The back panel contains the battery compartment and a fastener to
secure the test module to the Network Master main unit. There are also
various compliance and warning labels as well as the model/serial
number (item 3 in Figure 1.3-1).
Figure 1.3-1 Back Panel
1-8
Battery compartment
Fastener
Module model/serial label
Compliance and warning labels
1.3
1.3.1
1B
Back Panel
Power and Batteries
The unit can be powered in three ways.

External AC charger/adapter:
External car plug cord/adapter (optional):

Use this adapter to provide power from a car to charge the Ni-MH
battery pack.
Ni-MH rechargeable battery pack:

When installed, this battery powers the unit.
Note
Only use the Anritsu Ni-MH battery pack. Anritsu does not
guarantee the safety and function of other battery packs.
Replaceable batteries:
If no AC charger/adapter or Ni-MH battery is available, the unit can
be powered by four AA Ni-MH batteries.
1-9
Overview
Use this adapter to provide power from an AC source or to charge

the Ni-MH (nickel-metal hydride) battery pack. For details see AC
Charger/Adapter.
Chapter 1 Overview
1.3.2
12B
Installing Ni-MH Battery Pack

Install the Ni-MH battery pack as described below.
1. Power down the unit.
2.
Open the battery compartment (Figure 1.3-1) by pulling the latch

while lifting the battery compartment cover.
3.
Remove any installed batteries.
4.
Plug the connector on the Ni-MH battery pack into the socket next
to the module release latch (white plastic latch in battery
compartment).
5.
Slide the Ni-MH battery pack into the battery compartment making
sure that the battery release pull (red ribbon) is tucked underneath
the pack, but leaving enough of the release pull exposed to remove
the battery pack later when necessary. Also ensure the THIS SIDE
UP label is visible.
6.
Close the battery compartment cover.
Figure 1.3.2-1 Open Battery Compartment
Ni-MH battery pack plug

Module release latch
Ni-MH battery pack
Battery release pull (red ribbon)
1-10
1.3
Back Panel
WARNING
1
Overview
ALWAYS power down the Network Master before

removing the Ni-MH battery pack.
The battery pack and/or Network Master may be
damaged if the power is on while the pack is removed.
WARNING
Before storing the Network Master for a long time (1
to 2 months), remove the Ni-MH battery pack to avoid
damage to the battery pack and/or Network Master.
If storing the Network Master with the Ni-MH battery pack
installed, always recharge the battery pack periodically
(every 1 to 2 months).
1-11
Chapter 1 Overview
1.3.3
13B
Battery Replacement Ni-MH Pack To AA Ni-MH

Replace the Ni-MH battery pack with AA Ni-MH batteries as described
below:
1. Power down the unit. Open the battery compartment (Figure 1.3-1
for location) by pulling the latch while lifting the battery
compartment cover.
2.
Using the battery release pull (red ribbon), lift out the Ni-MH
Battery Pack and unplug it from its socket next to the module
release latch (white plastic latch).
3.
Insert four new AA Ni-MH batteries in the compartment according

to the battery polarity symbols (+ and ) next to the battery contacts.
4.
Close the battery compartment cover.
WARNING
ALWAYS power down the unit before removing old
AA Ni-MH batteries.
If the batteries are removed while the power is on,
settings and data files may be lost.
WARNING
Remove AA Ni-MH batteries from the Network Master
when storing it for a long period of time (1 to 2
months).
Storing the Network Master for a long period of time with
AA Ni-MH batteries installed will decrease the discharge
capacity of the batteries.
1-12
1.4
Bottom Panel
1.4 Bottom Panel

The bottom panel has a label with the main unit model/serial number.
1
Overview
Figure 1.4-1 Bottom Panel
1-13
Chapter 1 Overview
1.5 Top Connector Panel

The top connector panel contains the measurement ports used to connect
optical fibers or RJ45 cables to the network under test plus USB ports for
uploading and downloading files. The 9 V DC Power Connector and
Battery Status LED are also on the top panel.
Figure 1.5-1 shows a typical top panel.
Note
The top panel configuration differs with the installed optics and options.
Figure 1.5-1 MU909060A1 Top Panel with

Open Measurement Ports Cover
Measurement Port A
Measurement Port B
9 V DC Power Connector
Battery Status LED
USB (Type A) port
USB (Type B) port
Table 1.5-1 Models Names and Measurement Ports
Model Name
MU909060A1
MU909060A2
MU909060A3
1-14
Measurement Port A
RJ45
RJ45
SFP
Measurement Port B
SFP
RJ45
SFP
1.5
1.5.1
14B
Top Connector Panel
AC Charger/Adapter
The unit includes an AC Charger/Adapter. The Ni-MH Battery Pack
requires 3 hours to charge fully. The Network Master will not recharge
the Ni-MH Battery Pack while it is operating.
Figure 1.5.1-1 AC Charger/Adapter with Guard
Guard
Release
1-15
Overview
The AC Charger/Adapter transformer has four interchangeable plugs.

Use the correct plug.
Chapter 1 Overview
To prepare the AC Charger/Adapter:
1.
Pull the Release and remove the Guard if it is in place (Figure

1.5.1-1).
2.
Select the required plug from the AC Charger/Adapter kit. See the
following figure.
3.
Hold the Release down and insert the plug adapter, making sure
that the tab on the plug adapter is seated in the slot on the top of the
AC Charger/Adapter transformer.
4.
Release the Release, making sure that the tab on the Release is
seated in the slot on the base of the plug adapter.
AC Power Operation
Operate the Network Master on AC power as described below.
1-16
1.5
Top Connector Panel
To use the AC Charger/Adapter:

1.
Open the cover on the Network Master 9 V DC Connector on the top

connector panel (Figure 1.5-1) and plug in the jack from the AC
Charger/Adapter.
2.
Plug the AC Charger/Adapter transformer into an AC outlet.
Overview
Note
Ensure that the AC Charger/Adapter transformer has the correct
plug.
3.
Press the Menu/Power key
to start the Network Master.
CAUTION
Use the Network Master only with the Anritsu AC
Charger/Adapter.
Anritsu does not guarantee the safety and functionality of
other AC charger/adapters.
To charge the Ni-MH Battery Pack:
1.
Power down the unit.
2.
Open the cover on the Network Master 9 V DC Connector on the top

connector panel (Figure 1.5-1) and plug in the jack from the AC
Charger/Adapter.
3.
Plug the AC Charger/Adapter transformer into an AC outlet.
Note
Ensure that the AC Charger/Adapter transformer has the correct
plug.
4.
When the battery pack is fully charged, the Battery Status LED is
lit green. See Battery Status LED for details. A full charge takes
about 3 hours.
Note
The Network Master will not charge the battery pack while it is
being operated.
1-17
Chapter 1 Overview
1.5.2
15B
Battery Status LED

The Battery Status LED displays the current status of the
Ni-MH Battery Pack:
Red:
The battery pack is not charging for one of the following reasons:
When starting to charge, the temperature of the battery pack is lower

than 5C or higher than 45C. In this situation, disconnect the AC
adapter from the Network Master and wait until the temperature of
the battery pack is within the 5 to 45C range.
While charging, the temperature of the battery pack becomes lower
than 5C or higher than 60C. In this situation, charging resumes
automatically as soon as the temperature of the battery pack is within
the 5 to 45C range.
Charging has not finished within about 3 hours it normally takes to
charge the battery pack fully. To avoid overcharging, the unit stops
charging after about 3 hours.
If the Battery Status LED is always red, there is a problem with the
battery pack. Please contact the Anritsu Technical Support Center or
your local Anritsu representative (see Anritsu Corporation Contact).
Orange
The AC Charger/Adapter is plugged in and the battery pack is

charging.
Green
The AC Charger/Adapter is plugged in and the battery pack is fully
charged or the Network Master is operating. The battery pack will
continue charging in maintenance charge mode.
Note
Charging or discharging can be started at any time with minimum
battery memory issues. The battery pack can be left in
maintenance charge indefinitely.
1-18
1.5
1.5.3
16B
Top Connector Panel
RJ45 Port
See Table 1.5-1 for details on which models have the RJ45 option.
Connecting Cable to RJ45 port
1.
Open the cover on the port (Figure 1.5-1).
2.
Plug the RJ45 cable into the port
1-19
1
Overview
The RJ45 port (item 1 in Figure 1.5-1) offers access to the optional RJ45
test port. This port has an RJ45 connector that accepts standard RJ45
cables.
Note
Chapter 1 Overview
1.5.4
17B
SFP Port
The SFP ports (item 2 in Figure 1.5-1) are located on the top panel of the
Network Master and are accessed by opening the sliding cover (Figure
1.5-1). The modules can be either optical or electrical. The optical
modules have LC connectors and the electrical modules have an RJ45
connector.
Cleaning Optical Connectors
Cleaning the optical connectors as described below.
1.
Open the port cover.
2.
Blow clean, dry compressed air on the tip of the ferrule.
3.
Wipe the ferrule tip clean with a precision cleaning tissue or a lint
free (foam) swab moistened with isopropyl alcohol.
4.
Dry the ferrule tip with clean, dry compressed air.
Dirty Ferrule Tip
Clean Ferrule Tip
Figure 1.5.3.1-1 Magnified Ferrule Tip

5.
1-20
Option: With the Network Master powered down, inspect the ferrule
using a hand-held microscope or magnifier. It should look like the
clean ferrule tip in Figure 1.5.3.1-1.
1.5
Top Connector Panel
Connecting Fiber to Optical SFP modules

The optical SFP modules are used to connect optical fiber for optical test
applications.
1.
Open the cover on the port (Figure 1.5-1).
2.
Connect the test fiber to the measurement port.
Overview
To connect a fiber to the SFP module:
WARNING
Never force the connector ferrule or insert it at an
angle into the adapter.
Optical fibers suffer loss caused by microbends or other
stress. Position the patch cord to minimize mechanical
strain.
1-21
Chapter 1 Overview
1.5.5
18B
Connecting Peripheral Devices

The unit has two USB ports for connecting a USB device or PC.
USB (Type A) port
The USB (Type A) port is used to connect a USB memory stick (version
1.1) to the unit. Some USB memory sticks are not supported by this port.
Figure 1.5.5-1 USB (Type A) Port

The following message is displayed when the unit detects that a USB
device has been connected.
Figure 1.5.5-2 USB Storage Device Detected Dialog

Press the Set key to close the dialog and set the USB device as the
default storage.
1-22
1.5
Top Connector Panel
When the USB device is removed the following message is displayed

(Figure 1.5.5-2).
1
Overview
Figure 1.5.5-2 USB Storage Device Removed Dialog

Press the Set key to close the dialog so the internal drive is set as the
default storage drive.
WARNING
Do not remove USB memory while it is being
accessed or the memory or data may be damaged.
1-23
Chapter 1 Overview
USB (Type B) port
The internal memory of the Network Master can be accessed directly
from a PC by connecting a PC to the USB (Type B) using a USB A to USB
B cable.
Figure 1.5.5.2-1 USB (Type B) Port
WARNING
Before disconnecting the USB cable between the
Network Master and PC always press Safely Remove
Hardware in the Notification area in Microsoft
Windows, otherwise the internal memory on the
Network Master may be damaged.
1-24
1.5
1.5.6
19B
Top Connector Panel
Cautions on Handling Optical Fiber Cables
Optical fiber cables may degrade in performance or be damaged if

handled improperly.
Overview
Note the following points when handling them.
CAUTION
Do not pull the cable when removing the
connector.
Doing so may break the optical fiber inside the cable,
or remove the cable sheath from the optical
connector.
CAUTION
Do not excessively bend, fold, or pinch an
optical fiber cable.
Doing so may break the optical fiber inside the cable.
Keep the bend radius of an optical fiber cable at 30
mm or more. If the radius is less, optical fiber cable
loss will increase.
1-25
Chapter 1 Overview
CAUTION
Do not excessively pull on or twist an optical
fiber cable.
Also, do not hang anything by using a cable. Doing
so may break the optical fiber inside the cable.
CAUTION
Be careful not to hit the end of an optical
connector against anything hard such as the floor
or a desk by dropping the optical fiber cable.
Doing so may damage the connector end and
increase connection loss.
WARNING
Do not touch the end of a broken optical fiber
cable.
The broken optical fiber may pierce the skin, causing
injury.
CAUTION
Do not disassemble optical connectors.
Doing so may cause part to break or the performance
to degrade.
1-26
1.6
Changing Test Module
1.6 Changing Test Module

Remove the installed test module from the Network Master and install
the new test module as described below.
Overview
To change the test module:

1.
Power down the unit.
2.
Disconnect the AC Charger/Adapter, if connected.
3.
Loosen the Captive Fastener on the back panel (item 2 in Figure

1.3-1). When loose, the fastener slips free but remains attached to
the test module.
4.
Open the battery compartment (Figure 1.3-1) and remove the

battery pack or AA Ni-MH batteries.
5.
Hold down the module release latch (white plastic latch in battery
compartment item 2 in Figure 1.3.2-1) while pulling on the
Network Master to separate it from the test module.
Release the module Release latch after the Network Master and test
module have bee separated.
WARNING
The Network Master and test module are a close fit.
Be careful when separating the two.
6.
To install the new test module, align the two tabs on the back of the
Network Master (end opposite 100-pin connector) with the two slots
on the new test module (Figure 1.6-1).
1-27
Chapter 1 Overview
Figure 1.6-1 Alignment Tabs and Slots
Alignment tabs on Network Master main unit

Alignment slots on module
7.
Applying firm but gentle pressure, place the Network Master main
unit on the test module. DO NOT force the two sections together.
8.
Tighten the Captive Fastener.
9.
Replace any removed battery pack or AA Ni-MH batteries.
10. Replace the battery compartment cover.
1-28
1.7
Basic Usage Notes
1.7 Basic Usage Notes
WARNING
Overview
Measurement port cover

The cover prevents dust and other contaminants collecting in the
measurement port. Keep this cover closed except when a cable is
connected.
Condensation
Condensation may occur in the Network Master when it is taken into a
warm room after use outdoors, etc. In this case, allow the Network
Master to dry out thoroughly before powering up.
Temperature range
Use the unit within the operating temperature range (0 to +40C) and
store it within the storage temperature range (20 to +60C). If the unit
is left in a car or other enclosed space for a long time during summer, the
ambient temperature may exceed the specified range, resulting in
malfunction.
Safety
Only use the Anritsu AC Charger/Adapter or Ni-MH Battery Pack,
otherwise the unit may be damaged.
Laser
NEVER look directly into the Network Master optical connector or end of
a connected cable, otherwise laser light may enter the eye and cause
injury. In addition, some SFP modules output high-power optical signals.
To prevent damage to connected equipment, check that any connected
photo-receiver will not be saturated. Anritsu accepts no responsibility for
damage caused to connected communications devices.
Maintenance
Anritsu recommends annual inspections (charged) of the Network Master
by an Anritsu Customer Service Center.
For other usage notes, read the safety-related information in this manual
thoroughly before use.
1-29
Chapter 1 Outline
1-30.
Chapter 2 General Operation

This chapter describes the general system operation and setup.
2.1
2.2
2.4
2.5
2.6
2.7
2.8
2-3
2-3
2-3
2-4
2-5
2-5
2-5
2-5
2-6
2-8
2-9
2-9
2-9
2-11
2-11
2-12
2-12
2-13
2-14
2-15
2-16
2-17
2-18
2-19
2-20
2-21
2-21
2-22
2-22
2-23
2-24
2-25
2-26
2-26
2-27
2-28
2-28
2-29
2-29
2
General Operation
2.3
Power Up/Power Down..............................................

2.1.1 Power Up.......................................................
2.1.2 Power Down ..................................................
2.1.3 Temperature Monitoring ................................
General Functions .....................................................
2.2.1 Top Menu ......................................................
2.2.2 Mass Storage Menu ......................................
2.2.3 Launching Applications .................................
2.2.4 General Functions Pop-Up Menu..................
2.2.5 Setup .............................................................
2.2.6 Help Function ................................................
2.2.7 About Function ..............................................
2.2.8 Set to Defaults..................................................
Mass Storage.............................................................
2.3.1 Creating New Folder......................................
2.3.2 Deleting File...................................................
2.3.3 Deleting Multiple Files ...................................
2.3.4 Copying File...................................................
2.3.5 Copying Multiple Files ...................................
2.3.6 Renaming File or Folder................................
Print Screen ...............................................................
Status Screen ............................................................
2.5.1 Basic ..............................................................
2.5.2 ETH................................................................
2.5.3 IP ...................................................................
2.5.4 SFP................................................................
2.5.5 Top Bar..........................................................
Result Screens...........................................................
2.6.1 Result overview .............................................
2.6.2 Summary .......................................................
2.6.3 Event Log ......................................................
2.6.4 Statistics ........................................................
Save and Load...........................................................
2.7.1 Save Setup ....................................................
2.7.2 Load Setup ....................................................
2.7.3 Save Results .................................................
2.7.4 Load Results..................................................
Setup..........................................................................
2.8.1 Intelligent Setup.............................................
2-1

2.9
2-2
PDF Reports .............................................................. 2-30

2.9.1 Setup ............................................................. 2-31
2.9.2 Generating a report ....................................... 2-33
2.1
Power Up/Power Down
2.1 Power Up/Power Down

2.1.1
Power Up
Press the Menu/Power key. The Network Master performs a brief
self-test during which the Anritsu splash screen is displayed before
changing to the Top Menu screen.
2
General Operation
Figure 2.1.1-1 Top Menu Screen
Caution
If a screen similar to the one shown above is not displayed
after power up, the Network Master may have failed the
self-test. Switch the unit off and on (power down/power
up) again. If the problem persists, contact the Anritsu
Technical Support Center or your local Anritsu
representative.
2.1.2
Power Down
1.
Press the Menu/Power key to display a pop-up menu.
2.
Use the Down arrow key to highlight Power Down in the menu.
3.
Press the Set key to accept the highlighted menu selection. The
following message appears: Are you sure you want to Power Down?
4.
Highlight Yes and press the Set key.

Forcibly Power Down at any time by pressing the Menu/Power key
for 10 s.
2-3
2.1.3
Temperature Monitoring
The temperatures of the instrument and any connected SFP modules are
monitored.
Note
The temperature of the SFP module is only monitored if the
module complies with the SFP Transceiver MultiSource Agreement
and has integrated digital diagnostic monitoring functions.
If the temperature of the instrument or one of the SFP modules reaches
its maximum specified value, the instrument will automatically power
down. Before this happens a pop-up temperature alarm dialog is
displayed to notify that a power down is imminent (Figure 2.1.3-1).
Figure 2.1.3-1 Temperature Alarm Pop-up Dialog

The pop-up dialog indicates whether the instrument or one of the SFP
modules has reached the maximum temperature.
Note
There is a 4-second delay from displaying the pop-up dialog until
power down is started.
2-4
2.2
General Functions
2.2 General Functions

2.2.1
Top Menu
The Top Menu provides access to:
2.2.2
The Ethernet application

The Reflector application
The Self Diagnostics application
The Pass Through application
The mass storage menu by pressing the F4 key
The General Functions pop-up menu by pressing the Menu/Power key
Mass Storage Menu

At the Top Menu, press Mass Storage (F4). The Mass Storage screen is
displayed in the File Operations mode, to copy, delete, or rename files, as
well as to create new folders.
2.2.3
Launching Applications
1.
At the Top Menu, use the Left/Right/Up/Down arrow keys to

highlight the application to launch and press the Set key.
2.
The Top Menu screen closes and the selected application is launched.
2-5
2
General Operation
2.2.4
General Functions Pop-Up Menu

Press the Menu/Power key to display the General Functions pop-up
menu.
Figure. 2.2.4-1 General Functions Pop-up Menu

This menu provides access to the following:
Cancel
Cancel editing of the active popup.
PDF Report
Generates a PDF file of the results that are currently in

memory. Available on the Result overview and on the
specific result screens.
Setup
Accesses general setup for Network Master

Only visible from Top Menu
Load
Opens Mass Storage screen in Load mode to load setup or

result file
Only visible when test not running and not from Top
Menu
Refer to 2.7.2 Load Setup and 2.7.4 Load Results for
further details.
Save
Opens Mass Storage screen in Save mode to save setup

file
Only visible when test not running and not from Top
Menu
Refer to 2.7.1 Save Setup for further details.
Help
Displays help for current screen
Mass Storage Opens Mass Storage screen in File Operations mode, to

copy, delete, or rename files, as well as to create new
folders
2-6
Print Screen
Captures current screen as bitmap file to internal

memory
Top Menu
Closes currently running application and opens Top Menu

screen
2.2
Power Down
General Functions
Starts power down
2
General Operation
2-7
2.2.5
Setup
Use the following procedure to access the Setup screen
1.
With the Network Master powered up, press the Menu/Power key at
the Top Menu. The General Functions pop-up menu is displayed
with Setup highlighted.
2.
Press the Set key. The Setup screen is displayed.
Figure 2.2.5-1 Setup screen

3.
Use the Up and Down arrow keys to highlight Date & Time.
(a) Press the Set key. The Date and Time dialog box is displayed.
Use the Left and Right arrow keys to highlight the required
selection.
(b) Use the Up and Down arrow keys to scroll to the desired
setting.
(c)
Repeat steps 3(a) and 3(b) until the required date and time are
displayed in the dialog box.
(d) Press OK (F1) to accept the new date and time setting.
2-8
4.
Highlight Color Theme and use the Left and Right arrow keys to
scroll to the required color theme.
5.
Highlight Language and use the Left and Right arrow keys to scroll
to the required language.
6.
Highlight Auto Backlight and use the Left and Right arrow keys to
scroll to the required time interval to turn off the backlight
automatically when no keys have been pressed. Press any key to
restore the backlight. This function is active only when the
instrument is battery powered.
7.
Highlight Auto Power Off and then use the Left and Right arrow
keys to scroll to the desired time interval to automatically power
down the Network Master when no keys have been pressed. This
function is active only when the instrument is battery powered.
8.
Highlight Apply and press the Set key to apply the displayed
general settings.
2.2
2.2.6
General Functions
Help Function
Basic help information is available in the Setup screens and the Top
Menu.
To access Help:
Press the Menu/Power key in any of the Setup screens or the Top
Menu screen.
2.
Highlight Help in the pop-up menu.
3.
Press the Set key. The bottom half of the screen displays a dialog
containing the help.
4.
Press the Set key again to close the dialog box.
2
General Operation
2.2.7
1.
About Function
The About Function accesses the Version/Serial Number Information
window listing the framework and test application software version
levels, as well as the serial numbers of the Controller and Module.
To access the Version/Serial number information:
1.
Press the Menu/Power key in any of the Setup screens.
2.
Select About from the pop-up menu and press the Set key.
3.
The Version/Serial number info window is displayed.
4.
Review the information in the window and then

(a) With OK highlighted, press the Set key to close the window
Or
(b) Highlight Save and press the Set key. The version information
is saved to a text file in the Data folder and the window closes.
2.2.8 Set to Defaults

Use the following procedure to return to the factory default settings.
To reset the General Setup defaults from the Top Menu:
1.
Press the Menu/Power key.
2.
Highlight Setup at the pop-up menu and press the Set key. The
General Setup appears.
3.
Highlight Defaults and press the Set key.
4.
Highlight Apply and press the Set key. The Setup defaults are now
set and the Top Menu screen is re-displayed.
Note
The application-specific setup remains unchanged.
2-9

Note
As of the current software release, the Auto Backlight and Auto
Power Off parameters are the only General Setup parameters
re-set via the Defaults button.
To set the application-specific setups to factory default from the Top
Menu:
1.
Highlight the application to be reset.
2.
Press the Set key to start the application.
3.
4.
Highlight Load at the pop-up menu and press the Set key.
5.
Set Device to Internal and Folder to /data/
6.
Highlight factory_default.cfg.
7.
Press LOAD SETUP (F1).
Note
Only the currently active application is reset to factory default any
other application remain unchanged.
2-10
2.3
Mass Storage
2.3 Mass Storage

The Mass Storage selection accesses to the following file operations:
Creating new folder
Deleting files
Copying files
Renaming files
To access the Mass Storage file operations from an application:
Press the Menu/Power key. The General Functions pop-up menu is

displayed.
2.
Highlight Mass Storage and press the Set key. The Mass Storage
File Operations screen is displayed.
To access the Mass Storage file operations from the Top Menu:
1.
Press Mass Storage (F4).
Figure. 2.3-1 Mass Storage In File Operations Mode
2.3.1
Creating New Folder

Use the following procedure to create a new folder at the Mass Storage
File Operations screen.
1.
Access the Mass Storage screen in the File Operations mode.
2.
With the Device field highlighted, use the Left and Right arrow keys
to select the mass storage device: Internal or USB.
If no USB device is connected to the Network Master, the selection is
set automatically to Internal.
3.
Select the location for the new folder.
4.
Press File Operations (F1). The File Operations pop-up menu is

displayed with the New Folder selection highlighted.
5.
Press the Set key. The pop-up menu closes and a folder named
newFolder is added to the current directory.
2-11
General Operation
1.
2.3.2
Deleting File
Use the following procedure to delete a file at the Mass Storage File
Operations screen.
1.
Access the Mass Storage File Operations screen.
2.
If no USB device is connected to the Network Master, the selection is
set automatically to Internal.
3.
Navigate to and highlight the required file.
4.

displayed.
5.
Highlight Delete and press the Set key.
6.
The Confirm Delete dialog box is displayed. Select Yes and press the
Set key.
The dialog box closes and the file is deleted from the currently
displayed directory.
2.3.3
Deleting Multiple Files

Use the following procedure to delete multiple files at the Mass Storage
1.
2.
If no USB device is connected to the Network Master, the device
selection is set automatically to Internal.
3.
Navigate to the required directory/folder.
4.
Press Multi-Select Off (F2). The red label on the soft key changes to
On and an empty checkbox is displayed before each file name in the
current directory/folder.
5.
Highlight the first file to delete and press the Set key. A checkmark
is displayed in the checkbox for the highlighted file. Repeat until all
the required files are selected and continue to step 6.
Or
To select all the files in the current folder, press File Operations (F1),
highlight Select All, press the Set key, and continue from step 6.
2-12
6.
Press File Operations (F1) and then highlight Delete in the pop-up
menu.
7.
Press the Set key. The Confirm Delete dialog box is displayed.
2.3
2.3.4
Mass Storage
8.
Select Yes and press the Set key. The selected files are deleted.
9.
Press Exit (F4) to close the Mass Storage screen.
Copying File
Use the following procedure to copy a file at the Mass Storage File
Operations screen.
2.
3.
Navigate to and highlight the required file.
4.

displayed.
5.
Highlight Copy and press the Set key. The Destination window is
displayed in front of the Mass Storage File Operations screen.
Figure 2.3.4-1 Mass Storage Screen with Destination Window

6.
7.
Navigate to the required destination.
8.
Press Paste (F1). The Copied File(s) dialog is displayed. Confirm

that the file has been pasted to the required location and press the
Set key to close the dialog box and return to the Mass Storage
screen.
9.
2-13
General Operation
1.
2.3.5
Copying Multiple Files

Use the following procedure to copy multiple files in the Mass Storage
1.
2.
3.
Navigate to the required directory/folder.
4.
Press Multi-Select Off (F2). The red label on the soft key changes to
On and an empty checkbox is displayed before each file name in the
current directory/folder.
5.
Highlight the first file to copy and press the Set key. A checkmark is
displayed in the checkbox for the highlighted file. Repeat until all
the required files are selected and continue from step 6.
Or
To select all the files in the current folder, press File Operations (F1),
highlight Select All, press the Set key and then continue from step 6.
6.

displayed.
7.
Highlight Copy and press the Set key. The Destination window is
displayed in front of the Mass Storage File Operations screen.
8.
9.
Navigate to the required destination.
10. Press Paste (F1). The Copied File(s) dialog is displayed. Confirm
that the files have been pasted to the required location and press the
Set key to close the dialog and return to the Mass Storage screen.
11. Press Exit (F4) to close the Mass Storage screen.
Warning
When copying a file from one folder to another folder,
there is no warning message even if there is a file with the
same name in the destination folder. The old file will be
overwritten.
2-14
2.3
2.3.6
Mass Storage
Renaming File or Folder

Data files and folders can be renamed by accessing the Rename function
at the Mass Storage File Operations screen.
1.
2.
3.
Navigate to and highlight the required file or folder.
4.

displayed.
5.
Highlight Rename and press the Set key. The soft keyboard screen is
displayed.
(a) Use the BKSP soft key (F2) to clear the entry in the name field.
(b) Use the Left/Right/Up/Down arrow keys to highlight the
required letter in the character matrix.
(c)
Press the Set key to add the highlighted letter to the name field.
(d) Repeat steps 5(b) and 5(c) to complete the file/folder name.
6.
When the file/folder name is completed, press OK (F4). The

file/folder is saved with the new name and the unit returns to the
Mass Storage screen.
7.
2-15
General Operation

2.4 Print Screen

Use the Print Screen function to capture the current screen (screen
dump) as a bitmap (bmp) file. Bitmap files are saved in the Internal Data
directory.
1.
With the screen to be printed displayed, press the Menu/Power key.

A pop-up menu is displayed.
2.
Highlight Print Screen and press the Set key.
3.
The Print Screen Complete dialog box is displayed in 2 or 3 seconds.

Press the Set key to save the bitmap file to the Data folder in
internal memory.
Screen dumps are given a file name automatically with the following
format:
[email protected]
YYYY
MM
DD
HH
MM
SS
= Year
= Month
= Day
= Hour, 24-hour clock
= Minutes
= Seconds
For example [email protected]
2-16
2.5
Status Screen
2.5 Status Screen

When starting the Ethernet, the Reflector, or the Pass Through
application, the Status screen is displayed to give a quick overview of the
current traffic and link status. The Status screen consists of the following
tabs:
2-17
General Operation
Basic
ETH
IP
SFP (only for MU909060A1 and MU909060A3)
They are explained in the following sections together with the Top bar. To
toggle between tabs use the Left and Right arrow keys.
2.5.1
Basic
The Basic tab is the first tab (Figure 2.5.1-1) that is displayed when
starting an application (either Ethernet, Reflector or Pass Through). This
tab gives an overview of what connectors the hardware has and
information about link speed, mode and time.
1
2
3
4
5
6
7
8
Figure 2.5.1-1 Status (Basic)
[1] The picture shows the type of physical connector used by the
Network Master; the above shows two RJ-45 connectors. The two
states of the SFP connector are shown below.
SFP slot with module
SFP slot without module
[2] This shows the link speed and half (HDX) or full (FDX) duplex link
mode.
[3] This shows the current utilization as a percentage.
[4] This shows the percentages of incoming frames with errors.
[5] This shows the pin/pair crossing and what standard the current link
is using.
[6] This shows the elapsed link time for the two ports.
[7] This shows the total transmitted frames.
[8] This shows the total received frames.
Note
Timers/counters used in items 6, 7, and 8 above are reset when the
link is lost.
2-18
2.5
2.5.2
Status Screen
ETH
The ETH tab (Figure 2.5.2-1) shows an overview of the link auto
negotiation status, the capabilities of the link partners, and faults
occurring during linkup if any.
2
General Operation
1
2
3
4
5
6
7
Figure 2.5.2-1 Status (ETH)
[1] This display goes green when auto negotiation is completed.
[2] This display goes green if the link partner has MAC pause
implemented.
[3] This display goes green if the link partner supports asymmetric
pause.
[4] This display goes red when an error is discovered at the link partner.
[5] This displays whether the port is master or slave; it is supported
only for 1000 Mbps.
[6] This displays possible link speeds for full duplex (FDX).
[7] This displays possible link speeds for half duplex (HDX).
2-19
2.5.3
IP
The IP tab (Figure 2.5.3-1) shows an overview of the IP and DNS status;
the following information is displayed for one stream at both ports and
only for IPv4:
IP
Gateway
Network Mask
DNS
Lease time when DHCP lookup enabled
Note
When IPv6 is enabled, only the source IP is displayed.
If the multi-stream option is installed, a stream can be selected using the
Stream soft key (F4) at the bottom of the soft key menu.
Figure 2.5.3-1 Status (IP)
2-20
2.5
2.5.4
Status Screen
SFP
The SFP tab (Figure 2.5.4-1) is only available when the Network Master
has SFP slot(s). This tab displays hardware information for the
supported SFP modules.
2
General Operation
Figure 2.5.4-1 Status (SFP)
2.5.5
Top Bar
The Top bar (Figure 2.5.5-1) is shared by all screens and consists of six
sections.
Figure 2.5.5-1 Top Bar

1 This displays the title of the current screen.
2 A rotating star indicates that a test is running.
3 This indicates that incoming traffic is being filtered.
4 This indicates the port hardware and link for Port A and Port B. The
port type is indicated by the following icons.
(a) RJ-45 electrical
(b) SFP Optical
5 This indicates the time using the 24-hour clock.
6 This displays the power status.
(a) The Network Master is connected to the AC power adapter
.
(b) The Network Master is operating on battery
Note
The Network Master must be off to charge the battery.
2-21
2.6 Result Screens

2.6.1
Result overview
The Result overview screen is displayed automatically when a test is
started by pressing the Start key or when test results are loaded as
described in 2.7.4 Load Results.
The Result overview screen can also be accessed manually by pressing
the Result soft key (F3) on the general soft key panel displayed on the
Status and Test Automator screens.
If no test is running or no test has been started since the Ethernet
application was selected at the Top Menu, the Result overview screen is
blank.
Figure 2.6.1-1 Result overview Screen with Test Schedule

The test schedule displayed on the Result overview screen is similar to
the test schedule setup on the Test Automator screen. An LED at the left
of each test shows the test status as follows:
A grey (blinking) LED indicates the running test.
A green LED indicates that the test has been completed successfully
without errors.
A red LED indicates that the test has completed, but an error
occurred during the test.
A black LED indicates that the test has not yet been executed.
To access a more detailed result screen for the individual tests in the test
schedule, navigate to the required test using the Up and Down arrow
keys and press the Set key.
2-22
2.6
2.6.2
Result Screens
Summary
When the test schedule is executed, in addition to displaying the Result
overview screen, a Summary screen (Figure 2.6.2-1) is displayed for
viewing the event log and detailed statistics about the frames received
during execution of the tests in the schedule.
2
General Operation
Figure 2.6.2-1 Summary Screen Event Log Tab

To display the Summary screen, press the Summary soft key (F4) on the
Result overview screen or the specific test result screens. Press the Back
soft key (F1) to return to the previous screen.
Note
The Summary screen is shared by all tests in the test schedule.
Use the Left and Right arrow keys to toggle between the tabs on the
Summary screen.
2-23
2.6.3
Event Log
The event log is found at the Event Log tab on the Summary screen.
All relevant events occurring during execution of tests in the test
schedule are recorded in the event log. Each event includes a time stamp
with 1-second resolution in the format HH:MM:SS and a text description
of the event.
HH
MM
SS
2-24

= Minutes
= Seconds
2.6
2.6.4
Result Screens
Statistics
During execution of tests in the test schedule, detailed frame statistics
are calculated and displayed at the Statistics tab on the Summary
screen.
2
General Operation
Figure 2.6.4-1 Summary Screen Statistics Tab

The frame statistics for each port are as follows:
Total
Total number of frames received during test

schedule
Unicast
Number of received Unicast frames
Multicast
Number of received Multicast frames
Broadcast
Number of received Broadcast frames
FCS Errors
Number of frames with Frame Check Sequence

(FCS) errors detected during test schedule
Fragmented
Number of received fragmented frames
Oversized
Number of received oversized frames
Undersized
Number of received undersized frames
Collisions
Number of collisions detected (HDX only)
Preamble violations
Number of detected Preamble violations
IFG violations
Number of detected Inter Frame Gap (IFG)

violations
Severe IFG violations
Number of detected severe IFG violations
2-25
2.7 Save and Load

2.7.1
Save Setup
When saving a setup, a file containing the Interface setup and Test setup
is generated with file extension .cfg. The file name can be set by the user.
To save setup:
1. Press the Menu/Power key. The General Functions pop-up menu is
displayed.
2.
Highlight Save and press the Set key. The Mass Storage Save screen
is displayed.
3.
If the file name is to be changed, press the Set key to display the soft
keyboard screen.
4.
Use the Left and Right arrow keys to select the Device.
5.
Use the Up and Down arrow keys to select the Folder and file.
Figure 2.7.1-1 Mass Storage Save Screen

6.
2-26
Press SAVE SETUP to save (F1).
2.7
2.7.2
Save and Load
Load Setup
Setups can be loaded from internal memory or from a USB flash drive.
A setup file is supported only by its relevant application, i.e., a setup file
created by the Reflector application can only be loaded by the Reflector
application.
To load the setup file:

displayed.
2.
Highlight Load and press the Set key. The Mass Storage Load
screen is displayed.
3.
Use the Left and Right arrow keys to select the Device
4.
Use the Up and Down arrow keys and Set key to select the Folder
and file.
5.
When the required file is highlighted, press LOAD SETUP (F1) to

load it.
Figure 2.7.2-1 Mass Storage Load Screen

There is a file named factory_default.cfg in internal memory. It
contains the factory defaults. The factory default file only resets the
current application to the factory defaults; it does not reset any other
applications.
Note
A setup file can only be loaded by the same application as was used
to save it. For example, a Reflector setup file can only be loaded by
the Reflector application.
Note
Loading a setup requires the Network Master to have the same SW
options installed as when the setup was first saved. If any options
are missing, a pop-up window is displayed, showing the missing
SW options.
2-27
General Operation
1.
2.7.3
Save Results
When a test schedule is finished or stopped by the user, the results are
saved automatically to internal memory.
The path to the results is /Data/results. The extension for saved result
files is .res.
The results files are given a file name automatically with the format:
[email protected]
YYYY
MM
DD
HH
MM
SS
= Year
= Month
= Day
= Minutes
= Seconds
An example of a file name is [email protected].

The time in the file name is the time when the schedule was finished or
stopped.
2.7.4
Load Results
Results can be loaded from internal memory or from a USB flash drive.
Loading results reloads the contents on the result screens. Only one
result file can be loaded at one time.
When a new result file is loaded, a new result window displays the file
contents.
To load a Results file:
1.

displayed.
2.
Highlight Load and press the Set key. The Mass Storage load screen
is displayed.
3.
Use the Left and Right arrow keys to select the Device.
4.
Use the Up and Down arrow keys to select the Folder and file.
5.
Press LOAD RESULTS (F2) to load the results.
The Load Results screen is the same as the Load Setup screen. See
Figure 2.7.1-1
2-28
2.8
Setup
2.8 Setup
The setup for Network Master Gigabit Ethernet module applications is
comprised of several settings, and falls into two categories:
Interface setup
Settings for the instruments Ethernet interfaces.
Test setup
Settings for supported instrument tests.
Settings are controlled via checkboxes and pop-up dialogs. The specific
settings and how to change them are described in the Application
Ethernet and Application Reflector sections on pages 3-1 and 4-1,
respectively.
2.8.1
Intelligent Setup
Some settings depend on other settings. When these settings are changed,
it may be necessary to make additional changes to comply with the
required change.
The Intelligent setup function bridges the two setup categories. Changes to
the Interface setup may require changes to the Test setup and vice versa.
If a setting change requires additional changes, the Dependency pop-up
dialog is displayed (Figure 2.8.1-1).
Figure 2.8.1-1 Dependency Pop-up

[1] This lists the changes that must be enforced before the setting
changes can be performed. Use the Up and Down arrow keys to
scroll through the list.
[2] Select the OK button to change the setting, including all the settings
listed in item 1.
[3] Select the Cancel button to cancel the new setting.
2-29
General Operation
2.9 PDF Reports

The Network Master is able to generate a PDF report with the following
content:
Test schedule, setup and results.

Test statistics and event log.
Instrument setup.
User defined comments and logo.
The reports can be stored on an USB memory stick or on the internal

memory.
To access the PDF report screen:
1.
Navigate to either the Result overview, test specific or Summary

screen.
2.
3.
Select PDF report from the list.
Figure 2.9-1 Menu popup with PDF report
Note:
PDF Reports are only available in the Ethernet application.
2-30
2.9
2.9.1
PDF Reports
Setup
The PDF report screen consists of three tabs:
Basic
Comment
Logo
2
General Operation
To navigate between the tabs press the F2 soft key named Next Tab.
Basic
From this tab it is possible to setup what should be included in the
report.
Figure 2.9.1-1 PDF report Basic screen

Receivers/Transceivers
Select which port(s) to include results

and setups from.
General Include Setup
Check if interface and test setups

should be included in the report.
General Include Comment
Check if comments should be included

in the report.
2-31

Comment
From this tab it is possible to add comments that will be included on the
first page in the report. The comments will only be added if Include
Comment is checked under the Basic tab.
Figure 2.9.1-2 PDF report Comment screen

Use the Up/Down arrow keys to navigate between the fields and press
the Set key to edit the content.
2-32
2.9
PDF Reports
Logo
From this tab it is possible to add a logo to the report. The logo will
appear in the top left corner of every page.
2
General Operation
Figure 2.9.1-3 PDF report logo screen

Include Logo
If checked a logo will be included in the report.
Path
Choose a logo. This will open the Mass Storage

screen. When the desired logo is found press the
F1 soft key to load the image.
Note
The supported image formats are JPG and PNG.
2.9.2
Generating a report
To generate a report:
1.
Press the F4 soft key named Generate.
2.
Type in the desired name for the report in the Save As field.
3.
Select USB or Internal storage in the Device field.
4.
Navigate to the desired folder.
5.
Press the F1 soft key, called Save report, to save the report.
2-33
Figure 2.9.1-1 Save PDF report screen

Note
The PDF file extension (.pdf) is added automatically.
2-34.
Chapter 3 Ethernet Application

This chapter explains the functions of the Ethernet application.
3-2
3-3
3-4
3-15
3-19
3-20
3-23
3-23
3-29
3-30
3-30
3-31
3-32
3-32
3-35
3-36
3-36
3-38
3-39
3-39
3-40
3-41
3-41
3-48
3-53
3-56
3
Ethernet Application
3.1 Application Ethernet Status .......................................

3.2 Application Ethernet Setup ........................................
3.2.1 Interface General Setup.............................................
3.2.2 Interface Filter Setup .....................................
3.2.3 Advanced Setup ............................................
3.2.4 Test Automator ..............................................
3.3 Generator Test...........................................................
3.3.1 Generator Test Setup ....................................
3.3.2 Generator Test Results .................................
3.4 BER Test....................................................................
3.4.1 BER Test Setup.............................................
3.4.2 BER Test Results ..........................................
3.5 Stimuli ........................................................................
3.5.1 Stimuli Errors and Alarms..............................
3.5.2 Using Stimuli..................................................
3.6 Ping Test....................................................................
3.6.1 Ping Test Setup .............................................
3.6.2 Ping Test Results ..........................................
3.7 Cable Test..................................................................
3.7.1 Cable Test Setup...........................................
3.7.2 Cable Test Results ........................................
3.8 RFC2544 Tests..........................................................
3.8.1 RFC2544 Throughput Test Setup .................
3.8.2 RFC2544 Latency Test Setup .......................
3.8.3 RFC2544 Burst Test Setup ...........................
3.8.4 RFC2544 Tests Results ................................
3-1
Chapter 3 Application Ethernet
3.1 Application Ethernet Status

The Status screen is the first screen displayed when starting the
Ethernet application.
It gives an overview of the current hardware and Ethernet status. For
details about the Status screen tabs, refer to section 2.5.
Figure 3.1-1 Status Screen

The three buttons on the right are controlled by the F1 to F3 soft keys.
F1
Displays Status screen

See Figure 3.1-1.
F2
Displays /hides Setup selector

See section 3.2.
F3
Displays Result overview screen

See section 2.6.1.
3-2
3.2
Application Ethernet Setup
3.2 Application Ethernet Setup

There are two different types of setup for the Ethernet application.
Interface
Test Automator
Pressing the F2 soft key displays a selector to select between these two
types of setup.
3
Figure 3.2-1 Setup Selector

The interface setup is where the common setup for all tests is done.
Navigation throughout all the interface setup screens is done with the
Up, Down, Left and Right arrow keys. The red frame in Figure 3.2.1-1
shows the current selected item. The selection is set by pressing the Set
key.
3-3
3.2.1
Interface General Setup

Preface
Interface setup soft keys
2
3
Figure 3.2.1-1 Interface Setup Screen, MAC Setup Pane

[1] Soft keys on Interface Setup screen
Back
Returns to previous screen
Next Tab
Switches between General, Filter and Advanced

setup
Port A/B
Displays current port and changes port when

pressed
Stream 1 - 8
When the Multistream option is installed, this

soft key displays the current stream and selects
the stream when pressed.
[2] Tabs for General, Filter and Advanced setup

[3] Sets and displays status of headers in transmitted frames
Green indicates transmitted frames contains header
Black indicates transmitted frames will not contain header
Pressing the Set key while a header is selected toggles the header
on/off.
[4] Pane showing content of configured header or information about
header
3-4
3.2
Port setup pane
1
2
3
Figure 3.2.1-2 Interface Setup Screen, Port Setup Pane

[1] Indicates whether port interface is RJ-45 or SFP
[2] Displays pop-up to select between Auto Negotiation and Forced
[3] Displays pop-up to select advertised line speeds and duplexing
method during auto negotiation
[4] Displays pop-up to select preferred/required clock mode during 1000
Mbps auto negotiation
[5] Enables/disables physical layer Flow Control
3-5

MAC setup pane
Figure 3.2.1-3 Interface Setup Screen, MAC Setup Pane

[1] Sets Source MAC address
When the factory defaults are loaded, the Source MAC address is set
to the factory-assigned port-specific MAC address. Refer to section
2.7.2.
Note
Each port has one unique MAC address. When the Multistream
option is installed, the same address is set at all streams
3-6
3.2
VLAN setup pane
1
2
3
3
Figure 3.2.1-4 Interface Setup Screen, VLAN Setup Pane

[1] Sets VLAN ID
[2] Sets CFI (Canonical Format Indicator) Flag
[3] Sets VLAN Priority
LLC1 setup pane
1
2
3
Figure 3.2.1-5 Interface Setup Screen, LLC1 Setup Pane

[1] Displays value of DSAP (Destination Service Access Points) byte
[2] Displays value of SSAP (Source Service Access Points) byte
[3] Displays value of Control byte
3-7

SNAP setup pane
The SNAP header can only be inserted when the LLC1 header is present.
Figure 3.2.1-6 Interface Setup Screen, SNAP Setup Pane

[1] Displays value of OUI (Organization code) header field
3-8
3.2
IPv4 setup pane

The IPv4 header cannot be selected with the IPv6 header. If the IPv4
header is selected while the IPv6 header is already selected, the IPv6
header is deselected automatically.
1
2
3
4
5
Figure 3.2.1-7 Interface Setup Screen, IPv4 Setup Pane

[1] Sets value of Source IP Address or displays assigned IP address
when DHCP enabled
[2] To use DHCP, put a checkmark in the Use DHCP checkbox. This
makes the Network Master send a DHCP request. The status of the
request is indicated by the LED icon.
Black indicates DHCP not enabled
Green indicates DHCP enabled and DHCP request completed
Red indicates DHCP enabled but DHCP request not completed
Pressing the Setup button displays the DHCP Setup pop-up.
Figure 3.2.1-8 DHCP Setup Pop-Up
3-9

[3] Activating the Setup button brings up the DNS Setup pop-up.
Figure 3.2.1-9 DNS Setup Pop-Up

Set the IP addresses for the DNS servers at this pop-up. When the
DNS addresses are obtained using DHCP, the displayed IP
addresses are marked with an asterisk symbol (*).
[4] To use a gateway, put a checkmark in the Use Gateway checkbox.
Pressing the Setup button displays the Gateway Setup pop-up.
Figure 3.2.1-10 Gateway Setup Pop-Up

Set the gateway information at this pop-up. When the gateway IP
Address and subnet mask are obtained using DHCP, are marked
with an asterisk symbol (*).
[5] Sets value of DSCP/TOS header field
3-10
3.2
IPv4 setup pane (continued)
1
2
3
4
5

[1] Putting a checkmark in the More fragments (MF) checkbox sets the
More fragments bit in the flags section of the IP header.
[2] Putting a checkmark in the Dont fragment (DF) checkbox sets the
Dont fragment bit in the flags section of the IP header.
[3] Putting a checkmark in the Reserved (RES) checkbox sets the
Reserved bit in the flags section of the IP header.
[4] Sets Fragment Offset
[5] Sets TTL value
[6] Sets Protocol value
When UDP (See Figure 3.2.1-14) or TCP (See Figure 3.2.1-15) is
selected at the UDP or TCP Interface Setup panes this field displays
the corresponding protocol value.
3-11

IPv6 setup pane
The IPv6 header cannot be selected with the IPv4 header. If the IPv6
header is selected while the IPv4 header is already selected, the IPv4
header is deselected automatically.
1
2
3
4
5
[1] Sets value of Source IP Address
[2] Sets value of Traffic Class
[3] Sets value of Flow Label
[4] Sets value of Next Header field
When UDP (See Figure 3.2.1-14) or TCP (See Figure 3.2.1-15) is
selected at the UDP or TCP setup pane, this field displays the
corresponding protocol value.
[5] Sets value of Hop Limit
3-12
3.2
UDP setup pane
1
2
3
Figure 3.2.1-14 Interface Setup Screen, UDP Setup Pane

[1] Sets Source Port
[2] Sets Destination Port
3-13

TCP setup pane
1
2
3
4
5
6
Figure 3.2.1-15 Interface Setup Screen, TCP Setup Pane
[1] Sets Source Port
[2] Sets Destination Port
[3] Sets Sequence number
[4] Sets Ack. number (acknowledge number)
[5] Sets Reserved field
[6] Sets Flags field
TCP setup pane (continued)
1
2
Figure 3.2.1-16 Interface Setup Screen, TCP Setup Pane
[1] Sets Window value
[2] Sets Urgent Pointer value
3-14
3.2
3.2.2
Interface Filter Setup

From the Interface Filter Setup it is possible to setup filtering of
incoming frames. The user interface is similar to the Interface Setup so it
is easy to navigate and setup
Figure 3.2.2-1 Interface Setup Screen, Filter Tab

[1] Set and display status of filters for incoming frames
Filter applied to incoming frames
Filter not applied to incoming frames
Pressing the Set key while a filter is selected toggles the filter
on/off.
[2]
This symbol indicates a wildcard meaning Dont care

indicating that whatever it is replacing is not part of the filter. A
filter expression for a MAC address with the format
11:22:33:44:55:
means all frames where the first 5 bytes are
11:22:33:44:55 pass the filter regardless of the value of the last byte.
3-15

MAC filter setup pane
1
2
Figure 3.2.2-2 Interface Filter Setup Screen, MAC Filter Pane

[1] Sets filter value for Source MAC address
[2] Sets filter value for Destination MAC address
VLAN filter setup pane
1
2
3
Figure 3.2.2-3 Interface Filter Setup Screen, VLAN Filter Pane

[1] Sets filter value for VLAN ID
[2] Sets filter value for CFI Flag
[3] Sets filter value for VLAN Priority
3-16
3.2
MPLS filter setup pane
1
2
3
4
5
Figure 3.2.2-4 Interface Filter Setup Screen, MPLS Filter Pane

[1] Sets filter value for MPLS Label
[2] Sets filter value for MPLS TTL
[3] Sets filter value for Experimental Bit1
[6] Sets filter value for Bottom of stack flag
IPv4 filter setup pane
1
2
Figure 3.2.2-5 Interface Filter Setup Screen, IPv4 Filter Pane

[1] Sets filter value for Source IP Address
[2] Sets filter value for Dest. IP Address
3-17

IPv6 filter setup pane
1
2
Figure 3.2.2-6 Interface Filter Setup Screen, IPv6 Filter Pane

[1] Sets filter value for Source IP Address
[2] Sets filter value for Dest. IP Address
UDP/TCP filter setup pane
1
2
Figure 3.2.2-7 Interface Filter Setup Screen, UDP/TCP Filter Pane

[1] Sets filter value for UDP/TCP Source Port
[2] Sets filter value for UDP/TCP Dest. Port
3-18
3.2
3.2.3
Advanced Setup
Incoming Frames setup pane
1
2
[1] Answers ARP requests with MAC and IP addresses matching

settings shown in Figs. 3.2.1-3 and 3.2.1-7 when checkbox checked
[2] Answers pings (ICMP echo requests) with MAC and IP addresses
matching settings shown in figures 3.2.1-3 and 3.2.1-7 when
checkbox checked
[3] Network Master functions as master or slave at RFC2544
End-to-End test when checkbox checked
RX Setup pane
1
2
3
4
Figure 3.2.3-2 Interface Advanced Setup Screen, Rx Setup

[1] Sets minimum number of expected bytes in Preamble
[2] Ignore Preamble violations in results when checkbox checked
[3] Sets limit for minimum number of bytes expected in IFG
[4] Sets maximum number of bytes in frame before handled as oversized
frame
3-19
Figure 3.2.3-1 Interface Advanced Setup Screen, Incoming Frames
3.2.4 Test Automator

The Test Automator function selects the test or series of tests to run.
This initial setup screen is displayed when Test Automator is selected.
Figure 3.2.4-1 Test Automator Setup Screen

The Test Automator screen has the following soft keys.
Status (F1)
Returns to status screen
Setup (F2)
Displays setup selector shown in Figure 3.2-1.
Result (F3)
Displays results summary
The Test schedule box is navigated using the Up, Down, Left and Right
arrow keys. The red square shown in Figure 3.2.4-1 indicates the current
selection. To set the selection, press the Set key.
After the required tests have been set in Test schedule box press the
Start key to start.
3-20
3.2
Pressing the Set key shown in Figure 3.2.4-1 displays the test selection
pop-up shown in Figure 3.2.4-2.
Use the Up and Down arrow keys to navigate between the tests . Press
the Set key to select the test.
When a test is selected it is displayed in the Test schedule box.
Figure 3.2.4-3 Test Automator with Tests
3-21
Figure 3.2.4-2 Test Selection Pop-Up

Use the Up, Down, Left and Right arrow keys to move the red frame to
the following options:
Test setup: pressing Set while this is selected displays the
test-specific setup screens. This setup is described in the sections
about specific tests.
Remove test: pressing Set while this is selected, removes the test
from the Test schedule box.
Move test: pressing Set while this is selected moves the test as
shown:
Figure 3.2.4-4 Test Schedule with Test Movement Enabled

As shown in Figure 3.2.4-4, when the arrow is in bold, use the Up and
Down arrow keys to move the selected test up or down in the list.
Figure 3.2.4-5 Test Schedule with Test Moved

Pressing Set disables movement so the Up, Down, Left and Right arrow
keys can be used to select between the three test options again.
Figure 3.2.4-6 Test Schedule with Movement Disabled after Test

Moved
3-22
3.3
Generator Test
3.3 Generator Test

The Generator function is used to generate traffic and monitor an
Ethernet connection. It works in conjunction with Interface Setup.
The framing is set at the Interface Setup screen; the Generator Test
setup is used to define the line load and frame size profile.
3.3.1
Generator Test Setup
The Generator test setup screen has four panes:
Mode/Duration
Generator
Destination
Payload
The Mode/Duration pane shown in Figure 3.3.1-1 sets the port-specific

traffic duration and generator modes.
Figure 3.3.1-1 Generator Setup Screen, Mode/Duration Pane
3-23
3
Up to eight Generator tests can be added to the Test Automator. Each

test has seperate setup parameters. To setup a Generator test, press the
icon at the Test Automator screen. See section 3.2.4 for further
information about the Test Automator function.

There are two generator modes as described below:
Generator+Monitor
Generates traffic with the framing that is setup at Interface Setup and
at a rate specified at the Generator pane.
Monitor only
Starts Generator test without transmitting frames
Note
If a test is started in the Generator+Monitor mode with no active
streams, it switches automatically to the Monitor Only mode
during the test.
There are three Duration modes:
Continuous
Generator test runs until stopped manually
Seconds
Generator test runs for specified number of seconds
Frames
Generator test stops after specified number of frames sent
If no active streams are specified, the test stops immediately.
Note
When Continuous mode is set, the test runs until the user presses
the Start key, which will stop the whole test schedule. All tests in
the test schedule after this test are therefore never executed.
3-24
3.3
Generator Test
The Generator setup pane defines the Line Load and how Frame Size
changes during the test.
1
2
3
Note
Multiple streams are supported only if the Multistream option is
installed.
Pressing the Stream soft key (F4) displays the Stream Selector pop-up
(Figure 3.3.1-3). Green indicates an active stream and black indicates an
inactive stream (Stream Line Load set to Off.).
Figure 3.3.1-3 Generator Setup Screen, Stream Selector
3-25
Figure 3.3.1-2 Generator Setup Screen, Generator Pane

[1] Specifies line load used by stream
Line load can be displayed as either percentage or Mbps. The stream
is inactive when Stream Line Load is set to Off.
Total line load at the bottom of the pane shows the percentage and
number of active streams. More streams cannot be activated when
the total line load is 100%. Total line load is only displayed when the
Multistream option is installed.
[2] Defines how Frame Size should change during test
The following profiles are available:
Constant
Frame Size does not
change and constant size is
specified in Start field
Random
Generator sends frames of
random sizes between
values specified at Start
and End
Stepped
Frame Size incremented by
value specified at Step
from Start to End for
interval specified at
Duration and repeated
until test stopped
Note
When Generator Mode is set to Monitor Only, all active streams
are ignored.
3-26
3.3
Generator Test
The Destination setup pane is where destination the MAC and IP are
defined. The source MAC and IP are set at the Interface Setup screen.
3
MAC
The Destination MAC can be specified either manually or resolved by
ARP lookup. Put a checkmark in the Use ARP checkbox to enable ARP
lookup. A percentage of the current Stream Line Load can be used for
sending broadcast frames.
IP
The Dest. IP Address can be specified either manually or resolved by
DNS lookup. Put a checkmark in the Use DNS checkbox to enable DNS
lookup and input the host name.
The LED icon shows the lookup progress/result:
Black indicates Lookup not executed
Gray (Blinking) indicates lookup in progress
Green indicates Lookup succeeded
Red indicates Lookup failed
3-27
Figure 3.3.1-4 Generator Setup Screen, Destination Pane

The Payload setup pane specifies the frame payload. Detection of
Multistream frame loss is also enabled here.
Figure 3.3.1-5 Generator Setup Screen, Payload Pane

When the Multistream Frame Loss checkbox is checked, the transmitter
inserts the specified sequence number at the start of the frame payload
and the receiver starts detecting the sequence numbers.
To set up the generator, the user must consider the following:
Whether the instrument should act only as a monitor or should
generate traffic too.
The test duration.
The number of streams used when the Multistream option is installed.
The Frame Size Profile to use.
Whether the destination addresses are specified.
The type of payload to use.
3-28
3.3
3.3.2
Generator Test
Generator Test Results

The Generator Result screen (Figure 3.3.2-1) is accessed from the Result
overview screen. It summarizes traffic flow based on streams. Use the
Port (F3) and Stream (F4) soft keys to select which results are displayed.
Item
Description
Tx Total Frames
Tx Total Bytes
Tx Broadcast Frames
Tx Broadcast Bytes
Number of transmitted frames

Number of transmitted bytes
Number of transmitted broadcast frames
Number of transmitted broadcast bytes
Number of received error-free unicast
frames
Number of received bytes
Number of received frames with errors
Rx Good Frames
Rx Good Bytes
Rx Errored Frames
When Multistream Frame Loss is enabled, an extra results box is

displayed (Figure 3.3.2-2). The frame loss is displayed as the number of
frames and as a percentage.
Figure 3.3.2-2 Generator Results Screen with Frame Loss
3-29
Figure 3.3.2-1 Generator Results Screen, Normal
3.4 BER Test

The BER test is a quick and easy way to test a connection for bit errors.
The BER test setup is similar to the Generator test setup, but the BER
test can only be set for one stream. Refer to section 3.3.1 for details.
3.4.1 BER Test Setup

Up to eight BER Tests can be added to the test schedule in Test
Automator. Each test has seperate set of parameters. To setup a BER
test, press the
icon at the Test Automator screen. See section 3.2.4
for further information about Test Automator.
The BER test adds extra information to the transmitted frames that the
receivers detect and report as errors if the information is missing.
The only pane for the BER test is the BERT setup pane.
1
2
3
Figure 3.4.1-1 BERT Setup Pane

[1] Select Port
Enables the test port(s).

[2] Include address in filter on receiver
Adds extra filtering to specify what packets receiver detects
[3] Framed/Unframed
When Unframed is selected, the BERT generator transmits only a
Preamble and payload with no headers. When using this type of
transmission, it is also possible to add a sequence number to ensure
data packets are received in the correct sequence.
3-30
3.4
BER Test
Note
When the Both Ports setting is selected at Select Port, a Port
selection button is displayed at the F3 soft key on both the Setup
and Results screens.
3.4.2 BER Test Results

The BER Test results screen is accessed from the Result overview screen
(see section 2.6.1). It shows an overview of the incoming data and errors.
3
Figure 3.4.2-1 BERT Results Screen

Item
Pattern Bit Count
Pattern Errors
Pattern Errors(%)
Seq. Errors
Seq. Sync. Lost
Frame Loss
Frame Loss Seconds
Description
Number of received pattern bits
Number of received errored pattern bits
Pattern errors calculated as percentage
Number of packages received out of
sequence
Number of times sequence
synchronization lost based on gap in
received sequence numbers of 16
Number of lost frames when using
framed BERT
Number of seconds with frame loss
3-31
3.5 Stimuli
The Stimuli function is used to insert various errors, violations and
alarms. It is accessed using soft keys and there are Stimuli for:
Generator Test F2 soft key
BER Test F2 soft key
Note
Some types of errors are only supported by specific tests as
explained later.
3.5.1 Stimuli Errors and Alarms

There are two main types of stimuli:
Alarms
Error/Violations
Alarm insertion can be enabled or disabled, whereas errors and
violations can be inserted in bursts either manually or at intervals.
Figure 3.5.1-1 Stimuli Alarms pop-up

The Alarms pop-up which is the default Stimuli pop-up has two buttons:
Clear
This button resets Stimuli settings.
Alarms
This button reselects different types of alarms. When an alarm is
selected, it is immediately enabled if a test is running.
To switch between Errors/Violations and Alarms, use the Left and Right
arrow keys.
Figure 3.5.1-2 Stimuli Errors/Violations pop-up
3-32
3.5
Stimuli
The Errors/Violations pop-up has five buttons:

Clear
This button resets Stimuli settings and switches the pop-up back to
that the one shown in Figure 3.5.1-1.
Error/Violations
This button selects the type of inserted error or violation.
Error Insertion
This button defines how errors are inserted. Under normal
circumstances, one of following can be inserted:
Off
Sends selected error or violation each time Apply button pressed

Burst/Sec
Sends burst every 1 s
Burst/10Sec
Sends burst every 10 s
Burst*1E-2 to Burst*1E-7
This Error Insertion setting is only supported by the error type
PRBS Bit Error. When set the transmitted frames contains the
selected ratio of PRBS bit errors.
Error Burst Length
This button sets the number of errors per burst.
Apply
This button applies the above settings to the. Changes do not take
effect until this button is pressed.
The Apply button is only enabled during testing. Stimuli changes
made during setup are applied when starting the test, unless Manual
is chosen.
3-33
No Errors/Violations are inserted

Manual

The Network Master can generate two types of alarms and 10 types of
errors and violations.
Alarms:
Item
No Link
Remote Fault
Description
Turns off current port to simulate link
loss
Signals remote fault to link partner
during auto negotiation
Errors and Violations:

Item
IFG
FCS
Preamble
PAUSE frames
IP Checksum
Fragmented IP
Layer 4 Checksum
Error Symbol
PRBS Bit Error
BERT Seq. Error
Description
Detects Inter Frame Gap violation when
two received frames are too close
The standard minimum IFG is 12 bytes.
Inserts frames with wrong Frame Check
Sequence (FCS)
Inserts Preamble 1 byte shorter than
standard 8 bytes
Used as Ethernet flow control method by
sending Pause frames to stop transmitter
for defined time
Generate frames with wrong IP header
checksum
Generate fragmented frames broken into
smaller frames at IP layer level
This usually happens when frames are
routed through a network.
Inserts wrong UDP or TCP header
checksum
Inserts errored symbol at PHY 10-bit
coding
Inserts bit error in PRBS payload
Generates sequence error by changing
sequence numbers of two frames used for
BERT
Note
The PRBS Bit Error and BERT Seq. Error items are only
supported at BER tests.
3-34
3.5
Stimuli
3.5.2 Using Stimuli

Stimuli are accessed from the test setup and results screens.
If a Stimuli setting is changed during setup, it is applied when the test is
started. Manual insertion of Error/Violations are only applied when the
apply button is pressed.
Errors, violations and alarms can be inserted when the test is running.
Alarms are enabled immediately but errors and violations are enabled
only when the Apply button is pressed. Use this button each time an
error or violation is inserted manually.
Restarting the test does not clear the current Stimuli settings and
they are reapplied when the insertion method is not set to Manual
or Off. To not reapply Stimuli, clear them before restarting the
test.
Note
Each Generator test or BER test has separate Stimuli settings; if a
test is removed from Test Automator and added again later, the
stimuli settings will still be there.
3-35
Note
3.6 Ping Test

The Ping test is a quick and easy way to test, troubleshoot and verify a
connection and latency.
3.6.1
Ping Test Setup

Up to eight Ping tests can be added to the test schedule in Test
Automator. Each test has its own set of parameters. To setup a Ping test,
press the
icon at the Test Automator screen. See section 3.2.4 for
more information on Test Automator.
The Ping setup screen consists of two panes:
Destination
Test Config.
Destination pane
Figure 3.6.1-1 Ping Test Setup Screen, Destination Pane
MAC
The Destination MAC can be specified either manually or resolved by
ARP lookup. Put a checkmark in the Use ARP checkbox to enable ARP
lookup.
IP
The Dest. IP Address can either be specified manually or resolved by
DNS lookup. Put a checkmark in the Use DNS checkbox to enable DNS
lookup and input the host name.
3-36
3.6
Ping Test
The LED icon shows the lookup progress/result:

Black indicates lookup not execute.
Gray (Blinking) indicates lookup in progress
Green indicates lookup succeeded
Red indicates lookup failed
Test Config pane
3
Figure 3.6.1-2 Ping Test Setup Screen, Test Config. Pane

Item
Port Selection
Test Duration Mode
Test Duration Value

Interval
Frame size
Timeout
Description
The test can run on either Port A or Port B.
The test can run in three different modes.
Continuous when requiring
continuous Ping test
Seconds when time-limiting test in
seconds
Frames when limiting length by
number of ping requests
Frames or seconds
Number of seconds between ping requests
Frames are transmitted back-to-back at 0.
Frame size in bytes
Timeout in ms
Note
If the actual timeout period is longer than Interval, the Interval
setting is overruled.
Note
When Continuous mode is set, the test runs until the user presses
the Start key, which will stop the whole test schedule. All tests in
the test schedule after this test are therefore never executed.
3-37
3.6.2
Ping Test Results

The Ping results screen is divided into three parts.
Port A/B ping results (left)
Summary (top right)
Round trip time (bottom right)
Figure 3.6.2-1 The Ping Results Screen
3-38
Item
Description
Port A/B ping results
This lists the send requests. When a ping

test is running, the list always contains
the latest ping request. Navigate the list
using the Up and Down arrow keys. Press
the Set key to switch between the latest
results and manually navigating the list.
Summary
This displays the number of sent requests

and number of received and lost replies.
Round trip time
This displays the minimum, maximum

and average round trip times.
3.7
Cable Test
3.7 Cable Test

The Ethernet Cable Test uses Time Domain Reflectometry (TDR) to
validate and detect open and short CAT5/CAT5E cables. This test is
useful for installing and troubleshooting cables.
3.7.1
Cable Test Setup

Up to eight Cable tests can be added to the test schedule in Test
Automator. Each test has its own set of parameters. To setup the Cable
test, press the
icon at the Test Automator screen. See section 3.2.4
for more information on Test Automator.
3
Figure 3.7.1-1 Cable Test Port Selector Screen

Press the Set key to display the port selector pop-up.
Figure 3.7.1-2 Cable Test Port Selection Pop-Up

Use the Up and Down arrow keys to select the test port and set the port
using the Set key.
3-39
3.7.2
Cable Test Results
1
2
3
4
5
6
7
8
Figure 3.7.2-1 Cable Test Result Screen
[1] Displays approximate cable length
[2] Shows connected pin pairs
[3] Shows status of pairs
The pair status can be:
Normal Pair neither short nor open
Short Pair has short circuit
Open Pair open
Fail Test failed
[4] Shows whether pair Tx, Rx or bi-directional (e.g. BI DA, Bi
directional Data A)
[5] Shows pair polarity
[6] Shows approximate length (1 m) to short or open circuit
OK is displayed when there is no short or open circuit.
[7] Shows amplitude(Amp) of pair reflection (1V to +1 V)
[8] Shows pair skew (8 ns)
3-40
3.8
RFC2544 Tests
3.8 RFC2544 Tests

RFC2544 is a benchmarking methodology that defines several tests for
describing the performance characteristics of a network device (or
complete network). The Network Master includes several setups (test
modes) for covering all aspects of RFC2544 testing.
Note:
RFC2544 tests require the RFC2544 test option.
3.8.1 RFC2544 Throughput Test Setup
Up to eight RFC2544 Throughput tests can be added to the test schedule

in Test Automator. Each test has its own set of parameters. To setup a
icon at the Test Automator
RFC2544 Throughput test, press the
screen. See section 3.2.4 for more information on Test Automator.
Figure 3.8.1-1 RFC2544 Throughput Setup Screen, Test Mode Pane
To return to the Test Automator screen, press Back (F1).
3-41
The RFC2544 Throughput test measures the highest line load at which
the DUT (Device Under Test) can forward frames of specific size without
lost frames. It also displays the frame loss rate for different line loads for
a specific frame size.

Test Mode pane
The RFC2544 test mode and test port(s) are set at the Test Mode pane.
Note
The RFC2544 tests run independently on two ports. If both ports
are selected, the port panes display the Port A/B soft key. Use this
soft key to select which port to set.
The RFC2544 Throughput test can run in three modes:
Mode
Switch Router Test
Single Ended
Network Test
End to End Network

Test
Description
In this mode Network Master tests the
data link layer on a connected switch or
router. Both ports must be active and
linked. The IP and MAC addresses must
be swapped, ensuring that the switch
forwards frames from port A to port B
and vice versa.
This test is used when testing network by
reflecting traffic back to the Network
Master. It requires a device to reflect the
traffic back, such as a second Network
Master in reflector mode.
In this test mode, two Network Master
units work together performing a
RFC2544 test. The unit initiating the test
is the Master and the other unit is the
Slave. Control data is sent from the
Master on port A (or port B if only port B
is used). When the test is started on the
Master, the unit will try to contact the
Slave on the control port using the
Destination IP and MAC address (or
using ARP if selected). If the slave
receives the communication on a port
with matching Source address, the test
begins.
Note
Apart from the Address setup, both the Master and Slave Network
Master should have the Accept incoming End-to-End configuration
frames option enabled. See section 3.2.3 Interface Advanced setup.
3-42
3.8
RFC2544 Tests
The only setups at the Slave side are the source addresses and enabling
of Accept incoming End-to-End configuration frames. The complete
RFC2544 setup is transferred from the Master when the test is started.
Note:
When the test is started at the Master, a pop-up on the Slave
indicates that the unit is being remotely controlled and displays a
Disconnect key. The pop-up disappears when the test is completed
or stopped at the Master.
End-to-End setup
When the End-to-End test mode is selected the End to End pane is
displayed.
Figure 3.8.1-2 RFC2544 Throughput setup screen, End to End pane
When End to End One way test is selected, packets are sent only in one
direction during the test. Use the One way Direction selection to specify
the direction in which packets should be sent.
Test results can be stored on the slave if required. Select the Store
results on slave side checkbox to enable this feature. Results are always
stored on the Master side.
3-43
3
When the test is completed, the test results are transferred from the
Slave to the Master where they can be viewed by pressing the Results
Remote/Local soft key.

Duration pane
All RFC2544 tests are executed in steps. A step is a specific combination
of a frame size and line load. During a step, frames with the specified
size are transmitted at the specific line load. The number of steps run
during a test depends on the selected number of frame sizes and line
loads.
The Step Duration time can be set in number of seconds (min.3 seconds)
on the Duration pane. This is approximately the duration of each test
step.
The Test Repetitions field sets the number of times the complete test will
run. The possible setting range is 1 to 1000 times.
Figure 3.8.1-3 RFC2544 Throughput Setup Screen, Duration Pane
Destination pane
The destination setup is similar to that of the Ping test setup. See section
3.6.1 for further details.
3-44
3.8
RFC2544 Tests
Frame Size pane

The Frame Size pane has checkboxes for the predefined sizes 64, 128,
256, 512, 768, 1024, 1280, 1518 and Jumbo Frame. The jumbo frame size
can be set from 1519 to 10000.
Note
The RFC test cannot be started without selecting at least one
frame size.
Line Load pane
The Line Load setting range used in the test is specified as Min and Max.
The load is varied in intervals with the value specified in the Step field.
The test always starts at Max: and decreases until the line load is equal
to Min. Line loads can be in either Mbps or as a percentage of the current
line speed.
Figure 3.8.1-5 RFC2544 Throughput Setup Screen, Line Load Pane

If the Stop on no frame loss at maximum utilization checkbox is selected,
the test continues to test the next frame size when the current test step
at a specific line load and frame size do not have any frames lost. In
other words, the test ignores the rest of the steps.
3-45
Figure 3.8.1-4 RFC2544 Throughput Setup Screen, Frame Size Pane

If the Auto Search checkbox is checked, the test finds the maximum line
load at which no frames are lost, using the specified Resolution and
search mode. When Auto Search is selected the Step parameter is not
used.
Note
The Stop on no frame loss at maximum utilization and Auto
Search mechanisms cannot be enabled simultaneously.
Auto Search can run in two modes:
Item
Binary
Smart
Description
Performs binary search of specified line
load interval from Max to Min
Assumes higher probability of frame loss
occurring closer to Max: and performs
skewed binary search, searching higher
line loads first
The Resolution field specifies the auto search precision as a percentage of

the current line speed. A higher precision (lower percentage) increases
the test duration. The supported precisions are 0.1%, 1.0% and 10.0%.
3-46
3.8
RFC2544 Tests
Advanced pane
Various test-specific settings are on the Advanced pane.

When the Transmit learning frames prior to test checkbox is selected, the
RFC2544 test sends learning frames before the first test-step starts on
each port. This is used to train the network-equipment, so initial results
are more typical.
The receiver uses a filter to determine which frames should be counted in
the results. When the Include address in frame filter on receiver
checkbox is selected, the receiver uses the MAC and IP addresses of each
incoming frame in addition to the filter key used by default.
If more than one test repetition is performed (by setting Test Repetitions
> 1 at the Duration pane), enabling the Accumulate repeated steps
displays only one repetition in the result window. This repetition holds
the accumulated results for all repetitions during the test.
Throughput can be calculated at different layers of the OSI model. Use
the Calculation Layer field at the layer where throughput should be
calculated.
All throughput calculations are averaged over 1-second measurement
intervals. To average across the entire Step Duration, set the
Throughput Type field to Average. Otherwise, the throughput values will
be the Maximum obtained during the step.
3-47
Figure 3.8.1-6 RFC2544 Throughput Setup Screen, Advanced Pane
3.8.2 RFC2544 Latency Test Setup

The RFC2544 Latency test measures the latency of frames forwarded by
the DUT to clarify the DUT processing overhead for forwarding forward
frames. The test is performed for different line loads for a specific frame
size.
Up to eight RFC2544 Latency tests can be added to the test schedule in
Test Automator. Each test has its own set of parameters. To setup a
icon at the Test Automator screen.
RFC2544 Latency test, press the
See section 3.2.4 for more information on Test Automator.
Figure 3.8.2-1 RFC2544 Latency Setup Screen, Test Mode Pane
3-48
3.8
RFC2544 Tests
Test Mode pane

[1] Selects RFC2544 test mode
[2] Selects RFC2544 test port(s)
Note
The RFC2544 tests run independently on two ports. If both ports
are selected, the port specific panes display a Port A/B soft key.
Use this soft key to select the port to setup.
The RFC2544 Latency test runs in three modes:
Router Latency Test
Switch Router Test
Single Ended
Network Test
Description
In this test mode, the latency-test sends
ping frames to measure the response time
for router equipment. The line load setup
for the Router Latency Test is measured
in kbps. The maximum line load for the
Router Latency Test is 1000 kbps. The
Network Master can respond to incoming
ping frames, so it can be used to run the
Router Latency Test port to port if
required. The Router Latency Test
supports both IPv4/ICMPv4 and
IPv6/ICMPv6.
In this test mode, one Network Master
can switch the data link layer of a switch
or router. Both ports must be active and
linked in this mode. IP and MAC
addresses must be swapped, ensuring
that the switch forwards frames from
port A to port B and vice versa.
This test is used when testing network by

reflecting traffic back to the Network
Master. It requires a device to reflect the
traffic back, such as a second Network
Master in reflector mode.
3-49
Item

Duration pane
of a frame size and line load. During a step, frames with the specified
size are transmitted at the specific line load. The number of steps run
during a test depends on the selected number of frame sizes and line
loads.
The Step Duration time can be set in number of seconds (3 seconds) on
the Duration pane. This is approximately the time duration of each test
step.
run. The possible setting range is 1 to 1000 times. The Duration pane is
similar to the RFC2544 Throughtput Duration pane; see Figure 3.8.1-3.
Destination pane
The Destination setup is similar to that of the Ping test setup. See
section 3.6.1 for further details.
Frame Size pane
can be set from 1519 to 10000. The Frame Size pane is similar to the
RFC2544 Throughtput Frame Size pane; see Figure 3.8.1-4.
Note
The RFC test cannot be started without selecting at least one frame size.
3-50
3.8
RFC2544 Tests
Line Load pane

The line load range used in the test is specified as Min: and Max. The
load is varied in intervals using the value specified in the Step field. The
test always starts at Max: and decreases until the line load is equal to
Min. Line loads are either in Mbps or as a percentage of the current line
speed. However, in the Router Latency mode, line loads are presented in
kbps.
3
Figure 3.8.2-2 RFC2544 Latency Setup Screen, Line Load Pane in
Router Latency Mode
The RFC2544 Latency test can reference a preceding RFC2544
Throughput test and only run passed steps. Select the Only run steps
where preceding test passed checkbox to enable this feature and select a
Throughput test in the Reference Test field.
Figure 3.8.2-3 RFC2544 Latency Setup Screen, Line Load Pane
3-51

Note
The reference function requires the Throughput and Latency tests
to be in the same mode. Hence, it cannot be used when the Latency
test is in the Router Latency mode. The two tests must also use the
same port(s).
Using the Tolerance Level (utilization multiplier) field, it is possible to
tune the line loads used in the Latency test compared to the line loads
used in the referenced Throughput test. If the Tolerance Level is 100.0%,
the two tests use the same line loads; if 50.0% is set, the Latency test line
loads are half the line loads of the Throughput test, etc.
Advanced pane
The advanced setup is similar to that of the RFC2544 Throughput test
setup. See section 3.8.1 for further details.
3-52
3.8
RFC2544 Tests
3.8.3 RFC2544 Burst Test Setup

The RFC2544 Burst test is also called the burstability or back-to-back
test. It determines the largest number of frames transmitted with
minimum IFG (Inter Frame Gap) that the DUT can handle without
frame loss.
Up to eight RFC2544 Burst tests can be added to the test schedule in
Test Automator. Each test has its own set of parameters. To setup a
icon at the Test Automator screen. See
RFC2544 Burst test press the
section 3.2.4 for more information on Test Automator.
3
Figure 3.8.3-1 RFC2544 Burst Setup Screen, Test Mode Pane
3-53

Test Mode pane
The Test Mode setup is similar to that of the RFC2544 Throughput test
Duration pane
of a frame size and burst size. During a step, a specific number of frames
with a specified size are transmitted back-to-back. The number of steps
run during a test depends on the selected number of frame sizes and
burst sizes.
The Step Duration time can be set in number of seconds (3 seconds) on
the Duration pane. This is approximately the time duration of each test
step.
run. The possible setting range is 1 to 1000 times. The Duration pane is
similar to the RFC2544 Throughtput Duration pane; see Figure 3.8.1-3.
Destination pane
The Destination setup is similar to that of the Ping test setup. See 3.6.1
for further details.
Frame Size pane
can be set from 1519 to 10000. The Frame Size pane is similar to the
RFC2544 Throughtput Frame Size pane; see Figure 3.8.1-4.
Note
The RFC2544 test cannot be started without selecting at least one frame
size.
3-54
3.8
RFC2544 Tests
Burst Size pane

Burst Sizes can be set in two modes: Stepped or Constant. Use the Burst
Mode field to select the mode.
In the Stepped mode, the test burst size range is specified by Start burst
size and End burst size. The burst size is varied in intervals with the
value specified in the Step burst size field.
Figure 3.8.3-3 RFC2544 Burst Setup Screen, Burst Size Pane in

Constant Mode
In Constant mode, only one burst size is used for each frame size. The
burst size is specified in the Constant burst size field.
Advanced pane
The advanced setup is similar to that of the RFC2544 Throughput test
3-55
Figure 3.8.3-2 RFC2544 Burst Setup Screen, Burst Size Pane in

Stepped Mode
3.8.4
RFC2544 Tests Results

The RFC2544 tests results screen is divided in two. The left side lists all
currently tested steps. The steps are identified by Repetition and Step
separated by a colon. During testing, the results reflect the currently
running step. To navigate through previously performed steps, press the
Set key. A gray frame is displayed around the currently shown step. Use
the Up and Down arrow keys to navigate through the steps. Pressing the
Set key again removes the gray frame and the results follow the
currently running step automatically.
The right side of the screen displays results for the current step with
transmission (Tx) data at the top and receive (Rx) results at the bottom.
Note
Red numbers indicates frame loss.
3-56
3.8
RFC2544 Tests
RFC2544 Throughput:
Item
Description
Tx Utilization(Mbps)
Tx Frame Size(bytes)
Tx Total Frames
Tx Frame Rate(Fps)
Rx Total Frames
Rx Utilization(%)
Rx
Throughput(Mbps)
Transmitter use in Mbps

Size of transmitted frames
Number of transmitted frames
Transmitter frame rate
Number of received frames
Receiver use as percentage
Rx Frame Loss Min

Rx Frame Loss Max
Rx Frame Loss Avg
Minimum frame loss for step

Maximum frame loss for step
Average frame loss for step
Lost frames divided by expected number
of frames as percentage
Minimum for step
Maximum for step.
Average for step
Rx Loss Rate Min(%)
Rx Loss Rate Max(%)
Rx Loss Rate Avg(%)
Receiver use in Mbps
3-57
Figure 3.8.4-1 RFC2544 Throughput Results Screen, Single Ended

Test Mode

RFC2544 Latency:
Figure 3.8.4-2 RFC2544 Latency Results Screen, Switch Router Test

Mode
Item
Rx Jitter Min
Rx Jitter Max
Rx Jitter Avg
Rx Latency Min
Rx Latency Max
Rx Latency Avg
Description
Minimum jitter for step
Maximum jitter for step
Average jitter for step
Minimum latency for step
Maximum latency for step
Average latency for step
Note
When in the Router Latency Test mode, Mbps in Tx Utilization
and Rx Throughput changes to kbps.
3-58
3.8
RFC2544 Tests
RFC2544 Burst:
Item
Tx Burst Size
Rx Frame Loss Min
Rx Frame Loss Max
Rx Frame Loss Avg
Description
Transmitter burst size
Minimum frame loss for step
Maximum frame loss for step
Average frame loss for step
When Accumulate repeated steps is enabled, steps with the same Frame
Size and Line Load are accumulated, meaning Min/Max/Avg is measured
over all repetitions for a step.
To change the Tx port and corresponding Rx port, press the F3 soft key.
Note
The Tx and Rx ports vary with test mode and port relations. In the
Switch Router Test mode, Port A transmits to Port B and vice
versa. The Tx and Rx ports are then Tx (Port A) with Rx (Port B)
and Tx (Port B) with Rx (Port A).
When testing in the End to End Network Test mode, a new soft key
labeled Results is displayed to change between local and remote results
by pressing the F2 soft key.
3-59
Figure 3.8.4-3 RFC2544 Burst Results Screen, Switch Router Test

Mode

Figure 3.8.4-4 Results Soft Key showing Local Results (left) and
Remote Results (right)
Note
The Results soft key is only displayed when testing has ended.
3-60
Chapter 4 Application Reflector

The Reflector application is used to reflect incoming traffic, while giving
the user a simultaneous view of the current statistics.
4.1
4.2
4.3
Status.........................................................................
Setup Interface...........................................................
4.2.1 Port ................................................................
4.2.2 Reflector ........................................................
Result.........................................................................
4.3.1 Reflector ........................................................
4.3.2 Event Log and Statistics................................
4-2
4-3
4-4
4-6
4-7
4-7
4-8
4
Application Reflector
4-1
4.1 Status
The Status screen is the first screen that is displayed when starting the
Reflector application.
It gives an overview of the current hardware and Ethernet status. For
details about the Status screen tabs, refer to section 2.5.
Figure 4.1-1 Status Window, Basic tab

F1

See Figure 4.1-1.
F2
Activates Setup Interface screen

which is used to setup ports and
the Reflector test
See section 4.2.
F3
Shows test results for both ports

See section 4.3
These are the main soft keys for the Reflector application and they are
shared by all screens.
4-2
4.2
Setup Interface
4.2 Setup Interface

The Setup Interface screen consists of two panels:
Port Panel (Figure 4.2.1-1)
Reflector Panel (Figure 4.2.2-1)
When entering this screen, a new Port button (F4) is added at the bottom
of the soft key menu.
Figure 4.2-1 Port Button (Port A)

This button displays the currently active port and also allows the user to
switch between Port A and Port B.
4
4-3
4.2.1
Port
1
2
3
4
5
Figure 4.2.1-1 Setup Interface, Port Auto Negotiate

The arrow keys and the Set key are used to navigate and select settings.
See section 1.1.2.
The above figure shows the port setup screen when Auto Negotiate is
selected:
When Auto Negotiate selected at Port Mode (Figure 4.2.1-1):
[1] This switches the port on and off.
[2] This indicates the current interface type for the selected port (RJ-45
or SFP).
[3] This selects the mode for the linking port. There are two modes:
Auto Negotiate (Figure 4.2.1-1), or Forced (Figure 4.2.1-2).
[4] This selects the link speed modes broadcast by the Network Master.
[5] This selects which link partner is the master and which is the slave
during auto negotiation (1000 Mbps mode only).
4-4
4.2
Setup Interface
3
5
6
Figure 4.2.1-2 Setup Interface, Port Forced

When Forced selected at Port Mode (Figure 4.2.1-2):
[5] This selects the speed mode used by the Network Master.
[6] This scans and displays supported speeds.

[7] This is the Auto Detect (above item 6) start and stop button.
4-5
4.2.2
Reflector
The Reflector screen is used for making specific settings for the Reflector
test.
1
2
3
4
5
6
Figure 4.2.2-1 Setup Interface (Reflector)
[1] This is the mask setting that specifies the range of reflected MAC
addresses, excluding multicast and broadcast. See the following
example below for clarification.
Example 1: Reflects all MAC addresses with
the last three bytes of FC-0A-01
Example 2: Reflects only specified MAC
address A0-52-43-FC-0A-01
[2] This enables/disables IP address swapping for reflected data
packages.
[3] This sets the local IP address.
[4] This sets the local MAC address.
[5] This enables/disables answers to ARP requests.
[6] This enables/disables answers to ping requests. All ping requests are
reflected regardless of this setting.
4-6
4.3
Result
4.3 Result
The Result screen is blank when no test has been run, but starts
displaying results as soon as the test is started by pressing the Start key
(section 1.1.2). To disable the Reflector application, press the Start key
again.
After starting the test, the Network Master switches automatically to the
Result screen if it is not already displayed.
Note
1. The Network Master only reflects traffic while a test is running.
on the top bar indicates that the Reflector
2. An icon
application is enabled.
When the Result screen is opened, the default screen is the Reflector
screen (Figure 4.3.1-1) and displays an overview of current traffic
conditions. This screen is refreshed every 1 s until the Reflector test is
stopped.
2
Figure 4.3.1-1 Result overview Screen
[1] This is the overview of incoming traffic. Use the Statistics tab for
more detailed information.
[2] This is the overview of outgoing (reflected) traffic. The Reflector only
reflects unicast traffic.
4-7
4.3.1 Reflector
4.3.2 Event Log and Statistics

The Event Log and Statistics tabs are explained in section 2.6.3 and 2.6.4.
As mentioned above, the Statistics tab gives a detailed view of incoming
traffic. The Reflector tab gives an overview of received and reflected
traffic.
4-8.
Chapter 5 Pass Through

The Pass Through application passes the incoming traffic from one port
to the other, while simultaneously giving the user a view of the current
statistics.
5.1
5.2
5.3
5.4
Status.........................................................................
Setup Interface...........................................................
5.2.1 Port ................................................................
Testing .......................................................................
Result.........................................................................
5.4.1 Pass Through ................................................
5.4.2 Event Log ......................................................
5.4.3 Statistics ........................................................
5-2
5-3
5-3
5-5
5-6
5-6
5-7
5-7
5
Pass Through
5-1
Chapter 5 Pass through
5.1 Status
The Status screen is the first screen that is displayed when starting the
Pass Through application.
It gives an overview of the current hardware, Ethernet and SFP
(Optional) status. For details about the Status screen tabs, refer to
section 2.5.
Figure 5.1-1 Status Window, Basic tab

F1

See Figure 5.1-1.
F2
Activates Setup Interface screen

which is used to setup the ports
See section 5.2.
F3
Shows test results for both ports

See section 5.4
These are the main soft keys for the Pass Through application and they
are shared by all screens.
5-2
5.2
Setup Interface
5.2 Setup Interface

The Setup Interface screen consists of one panel:
Port Panel (Figure 5.2.1-1)
When entering this screen, a new Port button (F4) is added at the bottom
of the soft key menu.
Figure 5.2-1 Port Button, Port A

This button displays the currently active port and also allows the user to
switch between Port A and Port B.
5.2.1
Port
Pass Through
1
2
3
4
5
Figure 5.2.1-1 Setup Interface, Port Auto Negotiate

The Up/Down arrow keys and the Set key are for navigate and select
settings. See Section 1.2.2 Panel Keys.
When Auto Negotiate selected at Port Mode (Figure 5.2.1-1):
[1] This switches the port on and off.
[2] This indicates the current interface type for the selected port (RJ-45
or SFP).
[3] This selects the mode for the linking port. There are two modes:
Auto Negotiate (Figure 5.2.1-1), or Forced (Figure 5.2.1-2).
[4] This selects the link speed modes advertised by the Network Master.
[5] This selects which link partner is the master and which is the slave
during auto negotiation (1000 Mbps mode only).
5-3
5
6
Figure 5.2.1-2 Setup Interface, Port Forced

When Forced selected at Port Mode (Figure 5.2.1-2):
[5] This selects the speed mode used by the Network Master.
[6] This displays the Auto Detect result.
[7] This is the Auto Detect start and stop button.
5-4
5.3 Testing
5.3 Testing
To enable the pass through mode press the Start key. To disable the pass
through mode, press the Start key again.
Note
The Network Master will only pass frames while a test is running
icon on the
and port speed and duplex match, indicated by this
top bar.
If during testing link is lost or speed or duplex no longer matches, pass
through will be disabled. Pass through will be enabled when link is
reestablished and speed and duplex match.
5
Pass Through
5-5
5.4 Result
The Result screen is blank when no test has been run, but starts
displaying results as soon as the test is started. After starting the test,
the Network Master automatically switches to the Result overview
screen if it is not already displayed.
5.4.1 Pass Through

When the Result screen is opened, the default tab is Pass Through
(Figure 5.4.1-1). This tab displays an overview of current traffic
conditions and is refreshed every one second until the test is stopped.
Figure 5.4.1-1 Result Screen

[1] This is the overview of incoming traffic. Use the Statistics tab for
more detailed information.
5-6
5.4
Result
5.4.2 Event Log
Figure 5.4.2-1 Event Log

As described in section 5.3 pass through can be disabled/enabled if
certain conditions are met. This will be indicated in the Event Log with
the lines Pass though disabled or Pass though enabled, see figure 5.4.2-1.
The Event Log tab is explained more in depth in section 2.6.3.
Pass Through
5.4.3 Statistics
The Statistics tab is explained in 2.6.4.
5-7
5-8.
Chapter 6 Updating Firmware

The application software is updated by uploading the latest Anritsu
firmware. The firmware file extension is BBM.
6.1
Updating Firmware .................................................... 6-2
6
Updating Firmware
6-1
6.1 Updating Firmware

Use the following procedure to update the firmware.
CAUTION
Always connect the AC Charger/Adapter to the instrument
before updating the firmware.
1.
Copy the BBM file released by Anritsu to a USB flash drive (version
1.1 or later).
2.
Plug the USB flash drive into the USB (Type A) port on the
instrument.
3.
Hold down the F1 key while powering up the instrument (press the
Menu/Power key).
Figure 6.1-1 First Firmware Update Screen

4.
Release the Menu/Power key when the Anritsu splash screen

appears, but continue pressing the F1 key until the first Firmware
Update screen is displayed (Figure 6.1-1).
Note
If there is more that one BBM file saved on the USB flash drive,
the Choose Update File dialog is displayed in front of the first
Firmware Update screen. Select (highlight) the correct BBM file
and press the Set key to continue.
6-2
6.1
5.
Updating Firmware
The Finding Update File text changes to Extracting Update File.

When the update file is fully extracted, the Installing New Firmware
screen is displayed (Figure 6.1-2).
Figure 6.1-2 Installing New Firmware Screen

If desired the controller can be re-installed by selecting the
Re-Install Controller. This is only relevant when the version of the
currently installed controller and the version in the BBM update are
the same. If the Controller version in the BBM update file is newer
than the version currently installed, the new controller firmware is
installed automatically independently of this checkbox.
6.
Press the Set key to continue. The first Installing Update screen is
displayed (Figure 6.1-3).
Figure 6.1-3 First Installing Update screen
7.
The installation is complete when the Finish button is displayed

(Figure 6.1-4). Press the Set key to finish the firmware version
upgrade.
6-3
6
Updating Firmware
If wanted the internal user drives can be reformatted during

installation by selecting the Format Drives During Installation
checkbox..
Figure 6.1-4 Finished button
Warning
When Format Drives During Installation is checked,
all user data is lost. Backup all user data before
installing updates.
6-4.
Chapter 7 Service Information

This chapter describes the Self Diagnostics function and maintenance.
7.1
7.2
Self Diagnostics .........................................................

7.1.1 Starting and Stopping Self Diagnostics .........
7.1.2 Progress Bar..................................................
7.1.3 Test Results...................................................
7.1.4 Pass/Fail Indication .......................................
7.1.5 Scrolling In Result Box ..................................
7.1.6 Cursor Key Navigation...................................
7.1.7 Soft Key Navigation .......................................
Maintenance ..............................................................
7.2.1 Cleaning Optical Connectors.........................
7.2.2 Cleaning Network Master ..............................
7.2.3 User Calibration.............................................
7.2.4 Repacking for Shipment ................................
7-2
7-2
7-2
7-3
7-4
7-4
7-4
7-5
7-6
7-6
7-6
7-6
7-6
7
Service Information
7-1
7.1 Self Diagnostics

Self Diagnostics is an application that can verify whether the Network
Master Gigabit Ethernet module hardware is working properly.
Self Diagnostics is a separate application and can only be accessed from
the Top Menu. Therefore if an application is running it must be stopped
first by returning to the Top Menu.
Do the following to start the Self Diagnostics application:
1.
Navigate to the Top Menu by powering on the Network Master or

return from the currently running application.
2.
Highlight the Self Diagnostics button and press the Set key.
7.1.1 Starting and Stopping Self Diagnostics

To start Self Diagnostics:
1.
Highlight the Start button at the Self Diagnostics screen and press
the Set key, or press the Start key.
Figure 7.1.1-1 Highlighted Start button at Self Diagnostics Screen

While Self Diagnostics is running, the text on the Start button changes to
Stop.
To stop Self Diagnostics:
1.
7.1.2
Highlight the Stop button at the Self Diagnostics screen and press
the Set key, or press the Start key.
Progress Bar
When Self Diagnostics is running, a progress bar indicates progress of
the tests towards completion.
Figure 7.1.2-1 Progress Bar
7-2
7.1
7.1.3
Self Diagnostics
Test Results
When Self Diagnostics has been started, the Result box displays
information about completed tests.
Figure 7.1.3-1 Test Results in Result Box

Each completed test is described by a single line of text describing:
Test completed with or without errors
What has been tested
In addition, some tests contain information on test results (Figure
7.1.3-2).
Figure 7.1.3-2 Test Completed with Result Information

If a test is completed with an error, the text line starts with the word
ERROR (Figure 7.1.3-3).
7
Service Information
Figure 7.1.3-3 Example of Test Completed with Error
7-3
7.1.4
Pass/Fail Indication
When Self Diagnostics is completed, an LED on the GUI indicates
whether the diagnostics were completed with or without errors; if there
are errors, it indicates how many.
Figure 7.1.4-1 Indication of Test Completed Without Errors
Figure 7.1.4-2 Indication of Test Completed With Errors
7.1.5
Scrolling In Result Box

Because Self Diagnostics runs more tests than can be displayed at once
in the Result box, a scroll bar is displayed when the Result box is
overflowing.
Navigating and scrolling between individual tests in the Result box are
explained below.
7.1.6
Cursor Key Navigation

The Up and Down arrow keys are used to scroll in the result box if there
is any results and to toggle focus between the Start/Stop button and the
result box.
7-4
7.1
7.1.7
Self Diagnostics
Soft Key Navigation

When Self Diagnostics has completed with errors, the F1 and F2 soft
keys are used to navigate between errors.
Figure 7.1.6-1 Error Navigation Soft Keys

When the last error in the list is selected so there is no next error to
navigate to, the Next Error soft key is grayed out. The same applies to
the Previous Error soft key when the first error in the list is selected.
7
Service Information
7-5
7.2 Maintenance
User maintenance is limited to the following:
Cleaning connectors
Cleaning Network Master case
Warning
Do NOT attempt to service the Network Master yourself.
Request servicing by authorized Anritsu personnel only.
7.2.1
Cleaning Optical Connectors

Refer to the cleaning instructions in section 1.4.4.
7.2.2
Cleaning Network Master

If necessary, follow these steps to clean the unit case:
Unplug the power cord from the top panel before cleaning.
Clean the unit with a soft cloth lightly dampened with isopropyl
alcohol.
Do NOT clean the RJ-45 connector, and electric connector between the
module and main frame with any solvents. Use dry compressed air to
blow out any dust.
Caution
Do NOT use chemically active or abrasive materials to
clean the instrument.
7.2.3
User Calibration
The Network Master does not need calibration.
7.2.4
Repacking for Shipment

Keep the original packing for future use. Use the original packing when
returning the Network Master to Anritsu for servicing. Contact Anritsu
for instructions on returning the instrument.
7-6.
Appendix A Specifications
A.1
A.2
Specifications............................................................. A-2
Parts and Accessories ............................................... A-7
Appendix
Appendix A
A-1
A.1 Specifications
Table A.1-1 Specifications
Items
Specifications
Controller number
Controller name
Module number
Module name
MT9090A
Main Frame
MU909060A1, MU909060A2, MU909060A3
Gigabit Ethernet module
Application
Installation
Commissioning
QoS Verification
In-service troubleshooting
Multistream (SW option)
RFC 2544 Test (SW option)
MU909060A1: Gigabit Ethernet module with one electrical RJ-45 port
One electrical or optical SFP module can be installed.
MU909060A2: Gigabit Ethernet module with two electrical RJ-45 ports
MU909060A3: Gigabit Ethernet module
Two electrical or optical SFP modules can be installed.
Electrical interfaces (if installed): 10/100/1000 Mbps RJ-45 (10BASE-T,
100BASE-TX, 1000BASE-T)
Optical interfaces (if installed, depending on model and SFP module): 100
or 1000 Mbps LC connector (100BASE-FX, 1000BASE-SX, 1000BASE-LX
or 1000BASE-ZX)
Option 001
RFC 2544 Test option
Module
configurations
SW Options
Option 002
Ethernet
Interfaces
Multistream option
Duplex modes: Full duplex; Electrical 10/100 Mbps also Half duplex
Test configurations: Monitor/Generate, Pass Through, Reflector
Reflector delay: 2.44 s @ 1000 Mbps, 5.16 s @ 100 Mbps,
31.93 s @ 10 Mbps
Specification of optical modules purchased from Anritsu for Network

Master Gigabit Ethernet tester:
NB: Correct functioning is only guaranteed with Anritsu optical modules
specifically for MU909060A Series. Modules with extended temperature
range (up to +85C) must be used.
A-2
A.1
Items
Specifications
Specifications
Description
Min. input sensitivity

and wavelength range
Output power and

wavelength
1000BASE-S
X 850 nm
Multimode
1000BASE-L
X 1310 nm
Single mode
17
dBm
Min. 770 nm
Max. 860 nm
9.5 to
1.5 dBm
830 to 860
nm
20
dBm
10 to 3
dBm
1270 to
1355 nm
1000BASE-Z
X 1550 nm
Single mode
22
dBm
3 to 2
dBm
1480 to
1580 nm
100BASE-F
X 1310 nm
Multimode
31
dBm
20 to 15
dBm
1280 to
1380 nm
100BASE-L
X 1310 nm
Single mode
28
dBm
Min. 1260 nm
Max. 1580
nm
Min. 1260 nm
Max. 1580
nm
Min. 1270 nm
Max. 1600
nm
Min. 1260 nm
Max. 1600
nm
15 to 8
dBm
1261 to
1360 nm
Supported encapsulations: EtherType II (DIX v.2), IEEE 802.3 with 802.2

(LLC1), IEEE 802.3 with SNAP
A-3
Appendix A
Frame statistics:
Total frames, Unicast/multicast/broadcast frames
Number of fragmented frames, Oversized frames, Undersized (runts)
frames, FCS errored frames, Collisions (10/100 Mbps Half duplex)
Preamble violations, IFG violations (10/100Mbps non SFP), Severe IFG
violations (SFP)
Appendix
Measurements
and dedicated
tests
Traffic generation:
Variable line rate traffic generation, up to full line rate
Traffic shaping: Constant, Burst
Frame sizes can be set to constant, stepped or random length.
Configurable Ethernet (MAC) and IP source and destination addresses
(supports IPv4 and IPv6), UDP/TCP address and DSCP/TOS byte
Request IP source address from DHCP server (on/off)
Adjustable frame size from 38 to 10,000 bytes
User-defined VLAN ID and VLAN priority
User-defined traffic mix of unicast and broadcast frames
Generate and respond to pause frames
Answer incoming ARP request (On/Off)
Optional Ethernet (MAC) and IP address swapping (reflector configuration)
Status:
Link status, Signal and Frames present (utilization), Errored frames, Rx/Tx
frame count, Link time, Remote fault, Speed, Full/Half duplex, MDI/MDIX,
Interface type, Link partner abilities (Pause Capable and Asymmetric
pause Request), Local clock (1000 Mbps), DHCP lease time, Optical level of
optical interfaces
Items
Specifications
Electrical cable test:
Detection of MDI/MDIX mode, Link speed and status, Cable status and
distance to fault (if any), Polarity, Skew for 1000 Mbps
Pin mapping: Tx/Rx for 10/100 Mbps, DA, DB, DC, DD for 1000 Mbps
BER Test:
Generation and detection of test patterns, Count of errors in received test
pattern
Pattern generation: Unframed, Framed with IP header or Framed with IP
and TCP/UDP header
Test patterns:
PRBS 9, PRBS 11, PRBS 15, PRBS 20, PRBS 23, PRBS 29, PRBS 31, HF
test pattern, CRPAT, JTPAT, SPAT
Detection of sequence errors and loss of sequence synchronization
Ping test:
For connectivity and configuration check
Round Trip Time (RTT)
Supports IPv4 and IPv6 addressing
Answer incoming Ping requests (On/Off)
RFC 2544 Tests (option):
Single ended network test and Switch/Router test modes: Throughput and
utilization, Frame loss, Latency, Packet jitter, Back-to-back frames
(burstability)
End-to-end network test mode (two Network Master Gigabit Ethernet
testers in masterslave setup): Throughput and utilization, Frame loss,
Back-to-back frames (burstability)
Router latency test mode: IP ping-based latency, IP ping-based packet jitter
Multistream (option):
Number of streams: Max. 8 active streams on Ethernet line
Available information per stream: Frame loss count/rate, Frames and bytes
received, Frames and bytes transmitted
Report generation:
Generation of customized test result reports as pdf files with user logo and
comments
Event log:
Major events during test with 1-s precision time stamp, including Link/No
link and test Start/Stop
A-4
A.1
Items
Other functions
Specifications
Specifications
Date and time display/setting
Color theme: Default, Outdoor White, Night, Orange Crush, Lush Green
Language: English, Japanese, Spanish (Spain), Chinese (simplified)
Battery level indication
Internal memory:
40 MB internal memory for results, setups and screen shots
Stored configurations:
The user can save a number of configuration files for recall. Configuration
files can be transferred to other instruments using a USB memory stick or
PC.
Test Automator:
The user can create a macro to run several tests in sequence. The user can
also load, save, import and export test macros.
Display
Service interfaces
Laser safety
Power supply
Weight
21 W max. from AC supply

Up to 3 hours of continuous measurement (MU909060A2) with backlight on
at 25C using dedicated battery pack (Ni-MH 2700 mAh) or 4 AA Ni-MH
batteries
3.6 hours (Typical) at +10 to +30C with power off
MT9090A mainframe:
96 (H) x 180 (W) x 18 (D) mm
MU909060A1, MU909060A2, MU909060A3 Gigabit Ethernet Module:
96 (H) x 190 (W) x 30 (D) mm
800 g max.
Main frame and module with dedicated battery pack
A-5
Appendix A
Battery charging
time
Dimensions
Appendix
Power
consumption
Battery operation
time
4.3-inch color transmissive LCD (480 272 pixels, with LED backlight)
1 USB 1.1 Type A
(for USB memory stick)
1 USB 1.1 Type B
(USB mass storage; internal device accessed as removable media on PC
while connected to PC with USB cable)
Only applicable to MU909060A1 and MU909060A3
IEC 60825-1 Class 1, 21CFR1040.10
THIS PRODUCT COMPLIES WITH 21 CFR 1040.10 AND 1040.11
EXCEPT FOR DEVIATIONS PURSUANT TO LASER NOTICE. NO.50,
DATED JUNE 24, 2007.
Dedicated battery pack or four AA Ni-MH batteries
AC Adapter: 100 to 240 V, 50/60 Hz
Items
Specifications
Environmental
conditions
Operating
Temperature
Humidity
0 to +40C
85%, No condensation
Storage
Temperature
Humidity
20 to +60C
80%, No condensation
Vibration
IEC 60 068-2-6 Fc and IEC 60 068-2-64 Fh
Shock
IEC 60 068-2-27 Ea
Drop and topple
IEC 60 068-2-31 Ec
Bump
IEC 60 068-2-29 Eb
Free fall
IEC 60 068-2-32 Ed
EMC
EN 300 386
Dust proof,
Drip proof
JIS C0920 IP51
A-6
A.2
Parts and Accessories
A.2 Parts and Accessories

Table A.2-1 Parts and Accessories
Items
Model Name
G0240A
G0241A
G0242A
G0243A
G0244A
G0246A
J1271
J1273
Printed version
W3173AE
CLETOP type (one)

6 reel / pack
Pipe type (600 pcs. per pack)
Ni-MH Battery pack, 4.8 Vdc, 2700 mAh
100 to 240 Vac, 50/60 Hz, 9 Vdc, 1.67 A
Appendix A
Printed version
J1275
J1275B
J1275C
J1275D
Z0914A
Z0915A
Z1211A
G0202A
G0203A
J1402A
B0600A
B0601A
B0602A
Z1023A
W3166AE
Appendix
1000 Mbps SX SFP

1000 Mbps LX SFP
1000 Mbps ZX SFP
100 Mbps FX SFP
100 Mbps LX SFP
10/100/1000 Mbps RJ-45 SFP
OPTICALFIBERCORD (DUPLEX, SM,
LC-LC CONNECTOR), 2M
OPTICALFIBERCORD (DUPLEX, GI,
LC-LC CONNECTOR), 2M
LAN CABLE (CAT5E, STRAIGHT), 1M
LAN CABLE (CAT5E, STRAIGHT), 5M
LAN CABLE (CAT5E, CROSS), 1M
LAN CABLE (CAT5E, CROSS), 5M
Ferrule cleaner
Replacement reel for ferrule cleaner
Ferrule side face cleaner (MU, LC)
NiMH Battery pack
AC adapter
Car plug cord
Hard case
Standard soft case
Deluxe soft case
Strap
Network Master Gigabit Ethernet Tester
Operation Manual
- MT9090A Mainframe
- MU909060A1/2/3 Gigabit Ethernet Module
Network Master Gigabit Ethernet Tester Quick
Start Guide
- MT9090A Mainframe
- MU909060A1/2/3 Gigabit Ethernet Module
Specifications
A-7
A-8.
Appendix B Software Licenses

The MT9090A and MU909060A1/MU909060A2/MU909060A3 include the
software listed in the table below. These software are not covered by the
Anritsu Software License Agreement.
The details of each software license can be accessed at the following
URL:
https://www1.anritsu.co.jp/Download/Mservice/Login.asp
B.1
Software Licenses ..................................................... B-2
Appendix
Appendix B
B-1
Appendix B Software Licenses
B.1 Software Licenses

Table B.1-1 Software Licenses
Package name
B-2.
License
linux-2.6.20.1
busybox
e2fsprogs
sys5utils
util-linux
inetutils 1.5
freetype 2.1.7
mtd-utils
U-Boot 1.1.4
GPL
GPL1
GPL1
GPL1
GPL1
GPL1
FTL2GPL1
GPL1
GPL1
Microwindows
MPL3
flnx 0.18
dosfstools 2.11
portman 5 beta
Haru Free PDF
Library
Libpng
Tinyxml
Zlib
Lwip
LGPLexceptions4
GPL1
Other5
Remarks
zlib/libpng License
zlib/libpng License
zlib/libpng License
zlib/libpng License
BSD License
Microwindows was
downloaded
from
CVS on 2 Aug 2006.
Index
AC Charger/Adapter ..................................1-15
Calibration ....................................................7-6
Accumulate repeated steps
CFI (Canonical Format Indicator)...............3-7
RFC2544..................................................3-59
Advanced pane
RFC2544 Burst .......................................3-55
RFC2544 Latency ...................................3-52
RFC2544 Throughput.............................3-47
Alarms pop-up ............................................3-32
Amp
Cable Test................................................3-40
Answers ARP requests ...............................3-19
Changing Test Module ...............................1-27

Cleaning Optical Connectors .....................1-20
Collisions.....................................................2-25
Comment.....................................................2-32
Control...........................................................3-7
Destination pane
Generator ................................................3-27
Ping Test..................................................3-36
RFC2544 Burst .......................................3-54
RFC2544 Latency ...................................3-50
Answers pings ............................................3-19

Arrow keys ....................................................1-7
DF (Don't fragment) ...................................3-11
Back Panel ....................................................1-8
DNS Setup ..................................................3-10
Basic ............................................................2-31
DSAP Destination Service Access Points
Basic tab .....................................................2-18
.......................................................................3-7
Battery Status LED ...................................1-18
DSCP/TOS ..................................................3-10
BBM file ........................................................6-2
Duration pane
BERT Seq. Error ........................................3-34
RFC2544 Burst .......................................3-54

RFC2544 Latency ...................................3-50
RFC2544 Throughput.............................3-44
Binary
RFC2544 Throughput.............................3-46
BKSP soft key.............................................2-15
bmp..............................................................2-16
Bottom Panel ..............................................1-13
End to End Network Test
Burst Size pane
RFC2544 Throughput.............................3-42
End-to-End setup
RFC2544 Burst .......................................3-55
RFC2544 Throughput.............................3-43
Burst*1E-2..................................................3-33
Error Burst Length ....................................3-33
Burst/10Sec.................................................3-33
Error Symbol ..............................................3-34
Burst/Sec.....................................................3-33
Errors/Violations pop-up ............................3-33

ETH tab.......................................................2-19
Event Log
Pass Through ............................................5-7
Event Log tab..............................................2-24
Index-1
Index
Broadcast ....................................................2-25
Index
Fail
Jumbo Frame
Cable Test................................................3-40
RFC2544 Latency ...................................3-50
FCS..............................................................3-34
FCS (Frame Check Sequence) Errors .......2-25
Filter Tab ....................................................3-15
Layer 4 Checksum......................................3-34
Flow Control .................................................3-5

Flow Label ..................................................3-12
Line Load pane
Forcibly Power Down ...................................2-3
RFC2544 Latency ...................................3-51

RFC2544 Throughput.............................3-45
Format Drives During Installation.............6-3
Load Results ...............................................2-28
Fragmented ................................................2-25
Load Setup ..................................................2-27
Fragmented IP............................................3-34
Logo ................................................... 2-31, 2-33
Frame Loss .................................................3-31

Frame Loss Seconds...................................3-31
Frame Size pane
RFC2544 Burst .......................................3-54
RFC2544 Latency ...................................3-50
RFC2544 Throughput.............................3-45
Front Panel ...................................................1-4
Gateway Setup ...........................................3-10

Generator setup pane.................................3-25
Hop Limit....................................................3-12
Maintenance .................................................7-6
Mass Storage ..............................................2-11
Menu/Power key ...........................................1-7
MF ...............................................................3-11
Mode/Duration pane
Generator Test ........................................3-23
Move test.....................................................3-22
MPLS...........................................................3-17
Multicast .....................................................2-25
Multistream Frame Loss ...........................3-28
Next Header................................................3-12
Next Tab
IFG ..............................................................3-34
Ethernet ....................................................3-4
IFG violations .............................................2-25
Ni-MH Battery Pack ..................................1-10
Include Comment .......................................2-31
No Link .......................................................3-34
Intelligent Setup ........................................2-29
Normal
Interface setup............................................2-29
IP Checksum...............................................3-34
IP tab...........................................................2-20
IPv4 setup pane............................................3-9
IPv6 setup pane..........................................3-12
Index-2
Cable Test ................................................3-40
Index
Open
Receivers/Transceivers...............................2-31
Cable Test................................................3-40
Rechargeable battery pack ..........................1-9
Optical Fiber Cables ..................................1-25
Reflector ........................................................4-1
Option ...........................................................1-3
Re-Install Controller ....................................6-3
OUI................................................................3-8
Remote Fault ..............................................3-34
Oversized ....................................................2-25
Remove test.................................................3-22
Rename .......................................................2-15
Repetition
Panel Keys ....................................................1-6

Path .............................................................2-33
Pattern Bit Count.......................................3-31
Pattern Errors ............................................3-31
Pattern Errors(%).......................................3-31
PAUSE frames............................................3-34
Payload pane
Generator ................................................3-28
PDF report ..................................................2-30
ping results .................................................3-38
polarity
Cable Test................................................3-40
Port
Pass Through ............................................5-3
Reflector ....................................................4-4
Port Button ...................................................4-3
PRBS Bit Error...........................................3-34
Preamble .....................................................3-34
Print Screen.........................................2-6, 2-16
Replaceable batteries ...................................1-9

RES..............................................................3-11
Result
Pass Through ............................................5-6
Reflector.....................................................4-7
Result overview ..........................................2-22
Result overview screen...............................2-22
Result screen
Reflector.....................................................4-7
Result soft key ............................................2-22
Round trip time ..........................................3-38
Router Latency Test
RFC2544 Latency ...................................3-49
Rx Errored Frames.....................................3-29
Rx Frame Loss Avg
RFC2544........................................ 3-57, 3-59
Rx Frame Loss Max
RFC2544........................................ 3-57, 3-59
Rx Frame Loss Min
RFC2544........................................ 3-57, 3-59
Index-3
Index
Preamble violations....................................2-25
RFC2544..................................................3-56
Index
Rx Good Bytes ............................................3-29
Rx Good Frames .........................................3-29
Rx Jitter Avg
RFC2544..................................................3-58
Rx Jitter Max
RFC2544..................................................3-58
Rx Jitter Min
RFC2544..................................................3-58
Rx Latency Avg
RFC2544..................................................3-58
Rx Latency Max
RFC2544..................................................3-58
Rx Latency Min
RFC2544..................................................3-58
Rx Loss Rate Avg(%)
RFC2544..................................................3-57
Rx Loss Rate Max(%)
RFC2544..................................................3-57
Rx Loss Rate Min(%)
RFC2544..................................................3-57
Rx Throughput(Mbps)
RFC2544..................................................3-57
Rx Total Frames
RFC2544..................................................3-57
Rx Utilization(%)
RFC2544..................................................3-57
Setup Interface
Pass Through ............................................5-3
Reflector.....................................................4-3
Severe IFG violations.................................2-25
SFP tab........................................................2-21
Shipment.......................................................7-6
Short
Cable Test ................................................3-40
Single Ended Network Test
RFC2544 Latency ...................................3-49
RFC2544 Throughput.............................3-42
Skew
Cable Test ................................................3-40
Smart
RFC2544 Throughput.............................3-46
Soft keys........................................................1-5
Source MAC ..................................................3-6
SSAP (Source Service Access Points) ..........3-7
Standard Configuration ...............................1-2
Start key........................................................1-6
Statistics
Pass Through ............................................5-7
Statistics tab ...............................................2-25
Status
Pass Through ............................................5-2
Reflector.....................................................4-2
Status screen
Save Results ...............................................2-28

Save Setup ..................................................2-26
screen dump................................................2-16
Self Diagnostics ............................................7-2
Seq. Errors ..................................................3-31
Seq. Sync. Lost ...........................................3-31
Set key...........................................................1-7
Setup
PDF Reports............................................2-31
Index-4
Ethernet ....................................................3-2
Step
RFC2544..................................................3-56
Stream 1 - 8
Ethernet ....................................................3-4
Summary
Ping..........................................................3-38
Summary screen .........................................2-23
Summary soft key.......................................2-23
Switch Router Test
RFC2544 Latency ...................................3-49
RFC2544 Throughput.............................3-42
Index
Tx Frame Rate(Fps)
RFC2544..................................................3-57
Temperature Monitoring..............................2-4
Test Automator ...........................................3-20
Test Mode pane
RFC2544 Burst .......................................3-54
RFC2544 Latency ...................................3-49
RFC2544 Throughput.............................3-42
Test Repetitions
RFC2544 Throughput.............................3-44
Tx Frame Size(bytes)
RFC2544..................................................3-57
Tx Total Bytes.............................................3-29
Tx Total Frames..........................................3-29
RFC2544..................................................3-57
Tx Utilization(Mbps)
RFC2544..................................................3-57
Test schedule ..............................................3-20
Test setup...........................................2-29, 3-22
Undersized ..................................................2-25
Testing
Unframed ....................................................3-30
Pass Through ............................................5-5

Tolerance Level
Unicast ........................................................2-25
Updating Firmware......................................6-2
RFC2544 Latency ...................................3-52
USB (Type A) port ......................................1-22
Top Bar........................................................2-21
USB (Type B) port ......................................1-24
Top Connector Panel ..................................1-14

Top Menu ......................................................2-5
Total.............................................................2-25
Traffic Class................................................3-12
Tx Broadcast Bytes ....................................3-29
Tx Broadcast Frames .................................3-29
Tx Burst Size
VLAN setup pane .........................................3-7
Wildcard ......................................................3-15
RFC2544..................................................3-59
Index
Index-5
Index
Index-6.

Anritsu Ethernet Tester PDF

Uploaded by

Copyright:

Available Formats

Anritsu Ethernet Tester PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Anritsu Ethernet Tester PDF

Uploaded by

Copyright:

Available Formats

Network Master Series

For safety and warning information, please read this

Document No.: M-W3166AE-5.0

Symbols used in manual

This indicates a hazardous procedure or danger that could result in light-to-severe

Safety Symbols Used on Equipment and in Manual

These indicate that the marked part should be recycled.

Network Master Series

4. This equipment cannot be repaired by the operator. DO NOT attempt

5. The performance-guarantee seal verifies the integrity of the equipment.

8. DO NOT short the battery terminals and never attempt to disassemble

9. This instrument uses a Liquid Crystal Display (LCD). DO NOT subject

Lasers that are safe under reasonably foreseeable conditions

Table 1 Laser Safety Classifications Based on IEC 60825-1:2001

Class 1 AEL (W)

Pulse Width (s)/

Figure 1 Locations of Laser Beam Apertures and Affixed Labels

This instrument is designed for an industrial environment.

Anritsu Corporation Contact

Notes On Export Management

FOR CALIFORNIA USA ONLY

Crossed-out Wheeled Bin Symbol

Cautions against computer virus infection

C-Tick Conformity Marking

About This Manual

About This Manual........................................

Chapter 2 General Operation ....................

Power Up/Power Down.................................................

Chapter 3 Ethernet Application.................

Application Ethernet Status ..........................................

Chapter 5 Pass Through............................

Chapter 6 Updating Firmware ...................

Chapter 7 Service Information ..................

Appendix A Specifications .........................

Appendix B Software Licenses ..................

Self Diagnostics ............................................................

Index .......................................................... Index-1

Table 1.1.1-1 Standard configuration

Gigabit Ethernet Module

Below Options are available for Gigabit Ethernet Module.

1.2 Front Panel

Figure 1.2-1 Front Panel Layout

Displays title of current screen

Displays current time in 24-hour format

Display on-screen details

Arrow keys and Set key

The arrow keys (Left/Right/Up/Down) have the

Left arrow key

1.3 Back Panel

Figure 1.3-1 Back Panel

Power and Batteries

The unit can be powered in three ways.

External car plug cord/adapter (optional):

Ni-MH rechargeable battery pack:

Use this adapter to provide power from an AC source or to charge

Installing Ni-MH Battery Pack

Open the battery compartment (Figure 1.3-1) by pulling the latch

Remove any installed batteries.

Close the battery compartment cover.