SIEMENS Catalouge

Electropneumatic positioners
SIPART PS2
SIPART PS2, PS2 PA, PS2 FF,
PS2 EEx d, PS2 EEx d PA and PS2 EEx d FF
Overview
SIPART PS2 electropneumatic positioner
Benefits
SIPART PS2 positioners are characterized by significant advantages:
Simple installation and automatic commissioning (self-adjustment of zero and span)
Simple operation with
- Local operation and configuration of the device using three
input keys and a user-friendly two-line LCD
- Programming through SIMATIC PDM;
very high-quality control thanks to an online adaptation procedure
Negligible air consumption in stationary operation
"Tight shut-off" function (ensures maximum positioning pressure on the valve seat)
Numerous functions can be activated by simple configuring
(e.g. characteristics and limits)
Extensive diagnosis functions for valve and actuator
Only one device version for linear and part-turn actuators
Few moving parts, hence Insensitive to vibrations
External non-contacting position sensor as option for extreme
ambient conditions
Application
The SIPART PS2 positioner is used, for example, in the following
branches:
Chemical industry
Power stations
Paper and glass
Food and pharmaceuticals
Offshore plants
SIPART PS2 EEx d electropneumatic positioner in flameproof casing
The SIPART PS2 positioner is available:

For single-action actuators: in plastic, stainless steel or aluminium casings
For double-action actuators: in plastic casings and stainless
steel casings
For non-hazardous applications
For hazardous applications in the designs
- as intrinsically-safe device (EEx ia/ib) or
- in flameproof casing (EEx d) or
- in Ex n design (non sparking)
and in the versions:
With 0/4 ... 20 mA control communication through HART signal (as option)
With PROFIBUS PA communications interface (EEx ia)
With Foundation Fieldbus (FF) communications interface.
Explosion-proof versions
The basic version of the device is available in an intrinsicallysafe design with degree of protection EEx ia/ib or in a non-intrinsically-safe design for zone 2 (see Technical data for intrinsically-safe versions).
SIPART PS2 or SIPART PS2 in stainless steel casing
The SIPART PS2 electropneumatic positioner is used to control

the final control element of pneumatic linear or part-turn actuators. The electropneumatic positioner moves the actuator to a
valve position corresponding to the setpoint. Additional function
inputs can be used to block the valve or to set a safety position.
A binary input is present as standard in the basic device for this
purpose.
A non-intrinsically-safe application is permissible in zone 1 for

the SIPART PS2 EEx d flameproof version (see Technical data).
It is then permissible to use all option modules (except external
actuator travel detection systems and NCS).
Stainless steel casing for extreme ambient conditions
The SIPART PS2 is available in a stainless steel casing for use in
particularly aggressive environments (e.g. offshore operation,
chlorine plants etc.). The device functions are the same as with
the basic device.
Siemens FI 01 2005
6/3
SIPART PS2
Design
The SIPART PS2 positioner is a digital field device with a highlyintegrated microcontroller.
The positioner consists of the following components:
Casing and cover
PCB with corresponding electronics with or without communication through HART
or with electronics for communication in accordance with
- PROFIBUS PA specification, IEC 61158-2; bus-supplied
device, or
- Foundation Fieldbus (FF) specification, IEC 61158-2,
bus-supplied device
Actuator travel detection system
Terminal housing with screw terminals
Pneumatic valve manifold with piezoelectric valve precontrol.
The use of linear potentiometers is recommendable for very

small actuators with a short valve travel since, on the one hand,
the space required by the linear potentiometer is very small and,
on the other, the transmission characteristic is optimum for a
small travel.
The valve manifold is located in the housing, the pneumatic connections for the inlet air and the positioning pressure on the righthand side. A pressure gauge block and/or a safety solenoid
valve can be connected there as options. The circuit board container in the casing provides slots for separately ordered boards
with the following functions:
I y module
Position feedback as a two-wire signal 4 to 20 mA.
Separate connection of actuator travel detection system and controller

unit
Non-contacting position sensor (NCS)
Alarm module (3 outputs, 1 input)

Signaling of two limits of the travel or angle by binary signals.
The two limits can be set independently as maximum or minimum values.
Output of an alarm if the setpoint position of the final control
element is not reached in automatic mode or if a device fault
occurs.
Second binary input for alarm signals of for triggering safety
reactions or for blocking/signaling function or safety position.
All signals in the ly and alarm modules as well as the SIA module
are electrically isolated from one another and from the basic unit.
The outputs indicate self-signaling faults.
Limit signaling through slot-type initiators (SIA module)
Two limits can be signaled redundantly as NAMUR signals
(DIN19234) by slot-type initiators using an easy-to-fit module.
The module additionally contains an alarm output (see Alarm
module).
Stainless steel casing for extreme ambient conditions
The SIPART PS2 is available in a stainless steel casing for use in
particularly aggressive environments (e.g. offshore operation,
chlorine plants etc.). The device functions are the same as with
the basic device.
Separate mounting of actuator travel detection system and
controller unit
The actuator travel detection system and controller unit can be
connected separately for all casing versions of the SIPART PS2
(except flame-proof design). Measurement of the travel or angle
is carried out directly on the actuator. The controller unit can then
be fitted a certain distance away, e.g. on a mounting pipe or similar, and is connected to the travel detection system by an electric cable and to the actuator by one or two pneumatic lines.
Such a split design is frequently advantageous if the ambient
conditions at the fitting exceed the specified values for the positioner.
The following can be used for measuring the travel or angle:
NCS sensor
External position detection system C73451-A430-D87
A commercially available potentiometer (10 k resistance)
6/4
Siemens FI 01 2005
Non-contacting position sensor (NCS) for part-turn actuators (left) and for
linear actuators (right)
The actuator travel detection unit can also consist of a non-contacting position sensor instead of a potentiometer. All coupling
elements are omitted such as coupling wheel and driver pin with
part-turn actuators or lever and pick-up bracket with linear actuators.
This results in:
Even greater resistance to vibration and shock
No wear of sensor
Problem-free mounting on very small actuators
Negligible hysteresis with very small travels.
The sensor does not require an additional power supply, i.e.
SIPART PS2 can be operated in a 2-wire system. The NCS (Non
Contacting Position Sensor) consists of a potted sensor housing
which must be mounted permanently and a magnet which is
mounted on the spindle or lever shaft of linear actuators or on the
shaft butt of part-turn actuators.
The installation of a special EMC filter module in the positioner
(controller unit) is necessary in order to provide and guarantee a
connection level with EMC according to EN61326/A1 and
NAMUR NE21 when using external sensors (see Ordering data
for "EMC filter module").
SIPART PS2
Function
The SIPART PS2 electropneumatic positioner works in a completely different way to normal positioners.
Mode of operation
Comparison of the setpoint and the actual value takes place
electronically in a microcontroller. If the microcontroller detects a
deviation, it uses a 5-way switch procedure to control the piezoelectric valves, which in turn regulate the flow of air into the actuating chambers.
The microprocessor then outputs an electric control command to
the piezoelectric valve in accordance with the magnitude and direction of the deviation (deviation between setpoint w and control output x). The piezoelectric valve converts the command into
a pneumatic positional increment.
The positioner outputs a continuous signal in the area where
there is a large control deviation (high-speed zone); in areas of
moderate control deviation (slow-speed zone) it outputs a sequence of pulses. No positioning signals are output in the case
of a small control deviation (adaptive or variable dead zone).
The SIPART PS2 positioner is fitted to the linear or part-turn actuator using an appropriate mounting assembly.
The linear or rotary motion of the actuator is detected by the
mounting assembly and transferred through a rigid connection
to a potentiometer made of a wear-resistant plastic conductive
material.
The angular error of the pick-up in cases where the assembly is
mounted on a linear actuator is corrected automatically.
When connected in a 2-wire system, the SIPART PS2 draws its
power exclusively from the 4 to 20 mA setpoint signal. The electric power is connected through the 2-wire bus signal also with
PROFIBUS operation (SIPART PS2 PA). The same applies for the
Foundation Fieldbus version.
Pneumatic valve manifold with piezoelectric valve precontrol
The piezoelectric valve can release very short control pulses.
A high positioning accuracy can then be achieved. The pilot
element is a piezoelectric bending converter which switches the
pneumatic main control unit. The valve manifold is characterized
by an extremely long service life.
Local operation
Local operation is performed with the built-in LCD and the three
input keys. Switching between the operating levels Automatic,
Manual and Configuring is possible with the press of a button.
In Manual mode the drive can move over the entire range.
Operation and monitoring with the
SIMATIC PDM communications program
The SIMATIC PDM communications software permits easy remote operation and monitoring using a PC or laptop. The positioner can also be configured using this program. Parameters
which provide important information for maintenance and fault
diagnosis of the complete unit can additionally be determined
using process data and comparison data.
The SIMATIC PDM program is available for communication
through the HART interface and also for the PROFIBUS PA coupling.
Automatic commissioning
With a simple configuration menu the SIPART PS2 can be quickly
adapted to the fitting and adjusted by means of an automatic
startup function.
During initialization, the microcontroller determines the zero
point, full-scale value, the direction of action and the positioning
speed of the actuator. From this data it establishes the minimum
pulse time and the dead zone, thus optimizing the control.
Low air consumption
A hallmark of the SIPART PS2 is its own extremely low consumption of air. Normal air losses on conventional positioners are very
costly. Thanks to the use of modern piezoelectric technology, the
SIPART PS2 consumes air only when it is needed, which means
that it pays for itself within a very short time
Extensive diagnosis functions
The SIPART PS2 (6DR5...) has various monitoring functions with
which changes on the actuator and valve can be detected and
signaled if applicable when a selectable limit has been exceeded. This information may be important for diagnosis of the
actuator or valve. The measured values to be determined and
monitored, some of whose limits can be adjusted, include:
Travel integral
Number of changes in direction
Alarm counter
Self-adjusting dead zone
Valve limit position (e.g. wear of valve seat)
Operating hours (also according to temperature and positioning ranges) as well as min./max. temperature
Operating cycles of piezoelectric valves
Valve positioning time
Actuator leakages
Configuring
The following settings, for example, can be configured in configuring mode as required with the SIPART PS2 positioner:
Input current range 0 to 20 mA or 4 to 20 mA
Rising or falling characteristic at the setpoint input
Positioning speed limit (setpoint ramp)
Split-range operation; adjustable start-of-scale and full-scale
values
Response threshold (dead zone); self-adjusting or fixed
Direction of action; rising or falling output pressure with rising
setpoint
Limits (start-of-scale and full-scale values) of positioning
range
Limits (alarms) of the final control element position; minimum
and maximum values
Automatic "tight shut-off" (with adjustable response threshold)
The travel can be corrected in accordance with the valve characteristic.
Function of binary inputs
Function of alarm output etc.
Configuring the SIPART PS2 variants is identical in the main
points.
When operating the SIPART PS2 through the HART interface,

the connection is made directly to the 2-wire cable to the
SIPART PS2 positioner through a HART modem that can be connected to the PC COM interface. The signals needed for communication in conformity with the HART protocol are superimposed on the current signal in accordance with the Frequency
Shift Keying (FSK) method.
Siemens FI 01 2005
6/5
SIPART PS2
1
HART
2
BE1
3V
_
I W+
Inlet air
pZ
Exhaust
+24 V
p1
+5 V
W
I Wy
A
+U
p1
p2
Microcontroller
p2
Exhaust
W
x
x
U
6
I
5
BE2
A1
A2
I
9
8
p2
A1
1
2
3
4
5
6
A2
Motherboard with microcontroller and input circuit

Control panel with LCD and pushbuttons
Piezoelectric valve unit, always present
Valve unit, present as accessory in double-action positioner
Iy module for SIPART PS2 controller
Alarm module for 3 alarm outputs and one binay input
SIPART PS2, electropneumatic positioner, function diagram
6/6
Siemens FI 01 2005
p1
Travel
7 SIA module (slot initiator alarm module)

8 Spring loaded pneumatic actuator (single-action)
9 Springless pneumatic actuator (double-action)
Note:
Alarm module (6) and SIA module (7) can only be inserted
as alternatives.
p1
Travel
SIPART PS2
Technical specifications
Vibration resistance
SIPART PS2 (all versions)

General data
Travel range (linear actuators)
3 ... 130 mm (0.12 ... 5.12 inch)

(angle of feedback shaft 16 ... 90)
Angle of rotation (part-turn actuators)
30 ... 100
Installation
On linear actuators
On part-turn actuators
Using attachment set

6DR4004-8V and where necessary with an additional lever arm
6DR4004-8L on actuators
according to IEC 534-6 (NAMUR)
with ribs, bars or flat face
Using attachment set
6DR4004-8D on actuators with
mounting plane according to
VDI/VDE 3845 and DIN 3337:
The required mounting console
has to be provided on the actuator side; shaft with groove and
female thread M6
Controller
Five-point switch
Dead zone
- dEbA = Auto
- dEbA = 0.1 ... 10%
Self-adjusting
Self-adjusting or can be set as
fixed value
Self-adjusting or can be set as
fixed value
A/D converter
Scan time
Resolution
Transmission error
Temperature effect
10 ms
0.05%
0.2%
0.1%/10 K ( 0.1%/18 F)
Cycle time
20 mA/HART device
PA device
FF device
20 ms
60 ms
60 ms (min. loop time)
Binary input BE1 (terminals 9/10;

electrically connected to the basic
device)
Suitable only for floating contact;

max. contact load < 5 mA with
3V
Degree of protection
IP65 to EN 60 529/NEMA 4x
Mounting position
Any; pneumatic connections and

exhaust opening not facing up in
wet environment
CE marking
Conformity as regards EMC

Directive 89/336 EC in accordance with the following standards
EMC requirements
EN 61326/A1 Appendix A.1 and

NAMUR NE21 August 98
Material
Housing
- 6DR5..0-... (plastic)
- 6DR5..1-... (metal)
- 6DR5..2-... (stainless steel)
- 6DR5..5-... (metal, pressureproof)
Pressure gauge block
Glass-fiber-reinforced Macrolon
GK AISi12
Austenitic stainless steel mat.
No. 1.4581
GK AISi12
Aluminium AIMgSi, coated
Harmonic oscillations
(sine-wave) according to
DIN EN 60062-2-6/05.96
3.5 mm (0.14 inch), 2 ... 27 Hz

3 cycles/axis
Bumping (half-sine)
to DIN EN 60068-2-29/03.95
150 m/s (492 ft/s), 6 ms,

1000 shocks/axis
Noise (digitally controlled)

to DIN EN 60068-2-64/08.95
10 ... 200 Hz; 1 (m/s)/Hz

(3.28 (ft/s)/Hz)
98.1 m/s (321.84 ft/s),

27 ... 300 Hz, 3 cycles/axis
200 ... 500 Hz; 0.3 (m/s)/Hz

(0.98 (ft/s)/Hz)
4 hours/axis
Recommended continuous duty
range of the complete fitting
30 m/s ( 98.4 ft/s) without resonance sharpness
Weight, basic device

Plastic casing
Metal casing, aluminium
Metal casing, stainless steel
Metal casing EEx d version
Approx. 0.9 kg (0.90 kg)

Approx. 5.2 kg (11.46 lb)
Dimensions
See Dimension drawing
Climate class to DIN EN 60721-3-4 To IEC 721

Storage 1)
1K5, but -40 ... +80 C

(1K5, but -40 ... +176 F)
Transport 1)
2K4, but -40 ... +80 C

(2K4, but -40 ... +176 F)
Operation 2)
4K3, but -30 ... +80 C

(4K3, but -22 ... +176 F)
Certificate and approvals

Classification according to pressure For gases of fluid group 1, comequipment
plies with requirements of
directive (DRGL 97/23/EC)
article 3, paragraph 3 (sound
engineering practice SEP)
Pneumatic data
Power supply (inlet air)
Pressure
1.4 ... 7 bar (20.3 ... 101.5 psi):

Sufficiently greater than max.
drive pressure (actuating pressure)
Air quality to ISO 8573-1

Solid particle size and density
Class 2
Pressure dew point
Class 2 (min. 20 K (36 F) below

ambient temperature)
Oil content
Class 2
Unthrottled flow
Inlet air valve 3)
- 2 bar (29 psi)
- 4 bar (58 psi)
- 6 bar (87 psi)
4.1 Nm/h (18.1 USgpm)

7.1 Nm/h (31.3 USgpm)
9.8 Nm/h (43.1 USgpm)
Outlet air valve 3)

- 2 bar (29 psi)
- 4 bar (58 psi)
- 6 bar (87 psi)
8.2 Nm/h (36.1 USgpm)

13.7 Nm/h (60.3 USgpm)
19.2 Nm/h (84.5 USgpm)
Valve leakage
< 610-4 Nm/h (0.0026 USgpm)
Throttle ratio
Adjustable up to : 1
Power consumption in the controlled state
< 3.610-2 Nm/h (0.158 USgpm)
Types of actuators
In plastic casing
In aluminium casing
In flameproof casing
In stainless steel casing
Single-action and double-action

Single-action
1) During commissioning at 0 C ( 32 F) make sure that the valves are

flushed long enough with the dry medium.
2) At -10 C the display refresh rate of the LCD is limited. Only T4 is permissible when using Iy module.
3) With EEx d version (6DR5..5-...) the values are reduced by approx. 20%
Siemens FI 01 2005
6/7
SIPART PS2
SIPART PS2
Basic device
without Ex protection
Basic device
with EEx-d protection
(flameproof casing)
Basic device
Basic device
with EEx ia/ib protection with EEx n protection
Explosion protection to
EN 50014, EN 50020 and EN 50021
Without
EEx d
II 2 G EEx d II C T6
EEx ia/ib
II 2 G EEx ia/ib II C T6
EEx n
II 3 G EEx nA L [L] II C T6
Zone 1
Zone 2
Mounting location
Zone 1
-30 ... +80 C

Permissible ambient temperature for
(-22 ... +176 F)
operation
(for basic devices with EEX ia/ib and
EEx n protection the following applies:
At -10 C (+14 F) the display refresh
rate of the LCD is limited. Only T4 is
permissible when using Iy module.)
T4: -30 ... +80 C (-22 ... +176 F)

T5: -30 ... +65 C (-22 ... +149 F)
T6: -30 ... +50 C (-22 ... +122 F)
Electrical data
Input
2-wire connection (terminals 6/8)
Rated signal range
4 ... 20 mA
4 ... 20 mA
4 ... 20 mA
4 ... 20 mA
Current to maintain the power supply
3.6 mA
3.6 mA
3.6 mA
3.6 mA
- Typical
6.36 V (corresponds to
318 )
318 )
390 )
390 )
- Max.
324 )
324 )
415 )
415 )
- Typical
395 )
- Max.
420 )
- Typical
330 )
330 )
- Max.
336 )
336 )
- Typical
420 )
420 )
420 )
- Max.
440 )
440 )
440 )
Required load voltage

UB (corresponds to at 20 mA)
Without HART (6DR50..)
Without HART (6DR53..)
With HART (6DR51..)
With HART (6DR52..)
Static destruction limit
40 mA
Internal capacitance Ci
Without HART
22 nF
With HART
7 nF
0.12 mH
Internal inductance Li
Without HART
With HART
0.24 mH
For connection to power circuits with
intrinsically safe
Uo 30 V DC
Ik 100 mA
P1W
Ui 30 V DC
Ii 100 mA
6/8
Siemens FI 01 2005
SIPART PS2
SIPART PS2
Basic device
Basic device
(flameproof casing)
Basic device
Basic device
18 ... 35 V DC
18 ... 30 V DC
3-/4-wire device (terminals 2/4

and 6/8) (6DR52.. and 6DR53..)
Power supply UH
18 ... 35 V DC
Current consumption IH
(UH - 7.5 V)/2.4 kW [mA] (UH - 7.5 V)/2.4 kW [mA] (UH - 7.5 V)/2.4 kW [mA] (UH - 7.5 V)/2.4 kW [mA]
18 ... 30 V DC
22 nF
0.12 mH
intrinsically safe
Uo 30 V DC
Ik 100 mA
P1W
Ui 30 V DC
Ii 100 mA
Current input IW
Rated signal range
4 ... 20 mA
4 ... 20 mA
4 ... 20 mA
4 ... 20 mA
Load voltage at 20 mA
10 )
10 )
1 V (corresponds to
50 )
1 V (corresponds to
50 )
22 nF
Internal inductance (Li)
0.12 mH
intrinsically safe
Uo 30 V DC
Ik 100 mA
P1W
Ui 30 V DC
Ii 100 mA
Electrical isolation
between UH and IW
between UH and IW
between UH and IW
(2 intrinsically safe circuits)
between UH and IW
Test voltage
840 V DC (1 s) or 700 V DC (50 Hz, 1 s)
Connections
Electric
Screw terminals 2.5

AWG28-12
Cable gland M20 or
NPT
Screw terminals 2.5

AWG28-12
EEx d certified cable
gland M20x1.5, NPT
or M25x1.5
Pneumatic
Female thread G1/4 DIN 45141 or 18 NPT
Screw terminals 2.5

AWG28-12
Cable gland M20 or
NPT
Screw terminals 2.5

AWG28-12
Cable gland M20 or
NPT
External position sensor (potentiometer or NCS; as option)

Uo
<5V
<5V
Io
< 75 mA
< 75 mA
Is
<160 mA
<160 mA
Po
<120 mW
<120 mW
Maximum permissible external capaci-

tance Co
< 1 F
< 1 F
Maximum permissible external inductance Lo
< 1 mH
< 1 mH
Siemens FI 01 2005
6/9
SIPART PS2
SIPART PS2 PA
SIPART PS2 PA
Basic device
Basic device
(flameproof casing)
Basic device
Basic device
Without
EN 50.014, EN 50.020 and EN 50.021
EEx d
EEx ia/ib
II 2 G EEx d II C T4/T5/T6 II 2 G EEx ia/ib II C T6
EEx n
II 3 G EEx nA L [L] II C T6
Mounting location
Zone 1 or zone 2
Zone 2
-30 ... +80 C

Permissible ambient temperature for
(-22 ... +176 F)
operation
(for basic devices with Ex protection
the following applies: At -10 C
(+14 F) the display refresh rate of the
LCD is limited. Only T4 is permissible
when using Iy module.)
Zone 1
T4: -30 ... +80 C (-22 ... +176 F)

T5: -30 ... +65 C (-22 ... +149 F)
T6: -30 ... +50 C (-22 ... +122 F)
Electrical data
Input
Power supply (terminals 6/7)
Bus-supplied
Bus voltage
9 ... 32 V
Bus connection with FISCO supply

unit,
ia or ib group IIC or IIB
9 ... 32 V
9 ... 24 V
9 ... 32 V
17.5 V
- Max. supply voltage Uo
- Max. short-circuit current Io
- Max. power Po
Bus connection with barrier,

380 mA
5.32 W
- Max. supply voltage (Uo)
24 V
- Max. short-circuit current (Io)
250 mA
- Max. power Po
1.2 W
Current consumption
10.5 mA 10%
10.5 mA 10%
10.5 mA 10%
10.5 mA 10%
Fault current
0 mA
0 mA
0 mA
0 mA
Effective internal inductance
Li 8 mH
Effective internal capacitance
Negligible
Connection
Certified intrinsically safe

circuit
Safety shutdown can be activated with

coding bridge (terminals 81/82; electrically isolated from the basic device)
Input resistance
> 20 k
> 20 k
> 20 k
> 20 k
Signal status "0" (shutdown active)
0 ... 4.5 V or unused
Signal status "1" (shutdown not active)
13 ... 30 V
13 ... 30 V
13 ... 30 V
13 ... 30 V
Effective Internal capacitance Ci
Negligible
Effective internal inductance Li
Negligible
For connection to power supply with
Intrinsically safe
- Max. supply voltage Ui
< 30 V
< 30 V
- Max. short-circuit current Ii
<100 mA
<100 mA
- Maximum power Pi
<1W
Between basic device

and the input for safety
shutdown, as well as the
outputs of the option
modules

modules
The basic device and the

input to the safety shutdown, as well as the outputs of the option
modules, are individual,
intrinsically-safe circuits

modules
Test voltage
840 V DC, 1 s
840 V DC, 1 s
840 V DC, 1 s
840 V DC, 1 s
6/10
Siemens FI 01 2005
SIPART PS2
SIPART PS2 PA
SIPART PS2 PA
Basic device
Basic device
(flameproof casing)
Basic device
Basic device
Communication
Layers 1 and +2 according to PROFIBUS PA, transmission technique according to IEC 1158-2;
slave function; layer 7 (protocol layer) according to PROFIBUS DP,
EN 50170 standard with the extended PROFIBUS functions
(all data acyclic, manipulated variable, feedbacks and status also cyclic)
C2 connections
Four connections to master class 2 are supported,

automatic connection setup 60 s after break in communication;
Device profile
PROFIBUS PA profile B, version 3.0, more than 150 objects
Response time to master message
Typical 10 ms
Device address
126 (when delivered)
PC parameterizing software
SIMATIC PDM, for Windows 95 or Windows NT;

supports all device objects. The software is not included in the scope of delivery
Connections
Electric
Screw terminals 2.5

AWG28-12
Cable gland M20 or
1/2 NPT
Screw terminals 2.5

AWG28-12
EEx d certified cable
gland M20x1.5, 1/2 NPT
or M25x1.5
Screw terminals 2.5

AWG28-12
Cable gland M20 or
1/2 NPT
Screw terminals 2.5

AWG28-12
Cable gland M20 or
1/2 NPT
Pneumatic
Female thread G
DIN 45141 ( -18 NPT)
Female thread G
DIN 45141 ( -18 NPT)
Female thread G
DIN 45141 ( -18 NPT)
Female thread G
DIN 45141 ( -18 NPT)
Uo
<5V
<5V
Io
<75 mA
<75 mA
Is
<160 mA
<160 mA
Po
<120 mW
<120 mW
Maximum permissible external capacitance Co
< 1 F
< 1 F
< 1 mH
< 1 mH
External position sensor

(potentiometer or NCS; as option)
Siemens FI 01 2005
6/11
SIPART PS2
SIPART PS2 FF
SIPART PS2 FF
Basic device
Basic device
with EEx d protection,
flameproof casing
(available soon)
Basic device
with EEx ia/ib protection
EN 50014, EN 50020 and EN 50021
Without
EEx d
II 2 G EEx d II C T4/T5/T6
EEx ia/ib
II 2 G EEx ia/ib II C T6
Zone 1 or zone 2
Zone 1
Mounting location
Permissible ambient temperature for operation -30 ... +80 C (-22 ... +176 F)
(for basic devices with Ex protection the following applies: At -10 C (+14 F) the display refresh rate of the LCD is limited. Only
T4 is permissible when using Iy module.)
T4: -30 ... +80 C (-22 ... +176 F)

T5: -30 ... +65 C (-22 ... +149 F)
T6: -30 ... +50 C (-22 ... +122 F)
Electrical data
Input
Power supply (terminals 6/7)
Bus-supplied
Bus-supplied
Bus-supplied
Bus voltage
9 ... 32 V
9 ... 32 V
9 ... 24 V
Bus connection with FISCO supply unit, ia or

ib group IIC or IIB
17.5 V
380 mA
- Max. power Po
5.32 W
Bus connection with barrier,

24 V
250 mA
- Max. power Po
1.2 W
Electrical data
Current consumption
10.5 mA 10%
10.5 mA 10%
10.5 mA 10%
Fault current
0 mA
0 mA
0 mA
Effective internal inductance
Li 8 mH
Effective internal capacitance
Negligible
Connection
Certified intrinsically safe circuit
Input resistance
> 20 k
> 20 k
> 20 k
Signal status "0" (shutdown active)
Signal status "1" (shutdown not active)
13 ... 30 V
13 ... 30 V
13 ... 30 V
Effective Internal capacitance Ci
Negligible
Safety shutdown can be activated with coding bridge (terminals 81/82; electrically isolated from the basic device)
Effective internal inductance Li
Negligible
For connection to power supply with
Intrinsically safe
- Max. supply voltage Ui
< 30 V
- Maximum short-circuit current Ii
<100 mA
- Maximum power Pi
<1W
Between basic device and the

input for safety shutdown, as
well as the outputs of the option
modules
Between basic device and the

input for safety shutdown, as
well as the outputs of the option
modules
The basic device and the input

to the safety shutdown, as well
as the outputs of the option
modules, are individual, intrinsically-safe circuits
Test voltage
840 V DC, 1 s
840 V DC, 1 s
840 V DC, 1 s
6/12
Siemens FI 01 2005
SIPART PS2
SIPART PS2 FF
SIPART PS2 FF
Basic device
Basic device
with EEx d protection,
flameproof casing
(available soon)
Basic device
with EEx ia/ib protection
Communication
Communications group and class
According to technical specification of the Fieldbus Foundation for H1 communication
Function blocks
Group 3, Class 31PS (publisher, subscriber)

1 resource block (RB2)
1 analog output function block (AO)
1 PID function block (PID)
1 transducer block (standard advanced positioner valve)
Execution times of the blocks
AO: 50 ms
PID: 80 ms
Physical layer profile
123, 511
FF registration
Tested with ITK 4.51 or higher
Connections
Electric
Screw terminals 2.5 AWG28-12

Cable gland M20 or NPT

EEx d certified cable gland
M20x1.5, NPT or M25x1.5
Pneumatic
Female thread G1/4 DIN 45 141 ( -18 NPT)

Cable gland M20 or NPT
External position sensor

(potentiometer or NCS; as option)
Uo
<5V
Io
<75 mA
Is
<160 mA
Po
<120 mW
Maximum permissible external capacitance Co
< 1 F
< 1 mH
Siemens FI 01 2005
6/13
SIPART PS2
Option modules
Without Ex protection
With Ex protection
Ex protection to EN 50 014 and EN 50 020
II 2G EEx ia/ib II C T4/T5/T6
II 3G EEx nA L [L] II C T6
Mounting location
Zone 1
Zone 2
Permissible ambient temperature for opera- -30 ... +80 C (-22 ... +176 F)
tion
(For devices with Ex protection: Only in conjunction with the basic device 6DR5... -.E....
Only T4 is permissible when using Iy module)
T4: -30 ... +80 C (T4: -22 ... +176 F)

T5: -30 ... +65 C (-22 ... +149 F)
T6: -30 ... +50 C (-22 ... +122 F)
Electrical data
Alarm module
6DR4004-8A (without Ex protec- 6DR4004-6A (with Ex protection) 6DR4004-6A (with Ex protection)

tion)
Binary alarm outputs A1, A2 and alarm output

Signal status High (not responded)
Signal status Low* (responded)
(* Low is also the status when the basic
device is faulty or has not electric power supply)
Active, R = 1 k, +3/-1%*
Disabled, IR < 60 A
2.1 mA
1.2 mA
(* When used in the flameproof (Switching threshold with supcasing the current consumption ply to DIN 19234: UH = 8.2 V,
is limited to 10 mA per output.) Ri = 1k)
2.1 mA
1.2 mA
(Switching threshold with supply to DIN 19234: UH = 8.2 V,
Ri = 1k)
5.2 nF
Negligible
Power supply UH
35 V
Connection to power circuits with
intrinsically safe switching

amplifier DIN 19234
Uo 15.5 V DC
Ik 25 mA, P 64 mW
Ui 15.5 V DC
Electrically connected to the basic device

- Signal status 0
- Signal status 1
- Contact load
Floating contact, open

Floating contact, closed
3 V, 5 A

3 V, 5 A

3 V, 5 A
Electrically isolated from the basic device

- Signal status 0
- Signal status 1
- Natural resistance
4.5 V or open
13 V
25 k
4.5 V or open
13 V
25 k
4.5 V or open
13 V
25 k
Binary input BE2
Static destruction limit
35 V
Internal inductance and capacitance
Negligible
Connection to power circuits
Intrinsically safe Ui 25.2 V
Ui 25.2 V DC
The 3 outputs, the input BE2 and the basic device are electrically isolated from each other
Test voltage
840 V DC, 1 s
SIA module (not for EEx d version)
6DR4004-8G (without Ex protec- 6DR4004-6G (with Ex protection)

tion)
6DR4004-6G (with Ex protection)
Limit transmitter with slot-type initiators and

alarm output
2-wire connection
2-wire connection
2-wire connection
Ex protection
Without
II 2 G EEx ia/ib IIC T6
II 2 G EEx nA L [L] IIC T6
Connection
2-wire system to DIN 19234

(NAMUR), for switching amplifier (NAMUR), for switching amplifier (NAMUR), for switching amplifier
to be connected on load side
2 slot-type initiators
Type SJ2-SN
Type SJ2-SN
Type SJ2-SN
Function
NC (normally closed)
Connection to power circuits with
nominal voltage 8 V
Current consumption:
3 mA (limit value not
responded)
1 mA (limit value
responded)
Intrinsically safe switching

amplifier DIN 19 234
Ui 15.5 V DC
Ii 25 mA, Pi 64 mW
Ui 15.5 V DC
Pi 64 mW
Internal capacitance
41 nF
Internal inductance
100 mH
The 3 outputs are electrically

isolated from the basic device


Test voltage
840 V DC, 1 s
840 V DC, 1 s
840 V DC, 1 s
Alarm output
See Alarm module
See Alarm module
See Alarm module
6/14
Siemens FI 01 2005
840 V DC, 1 s
840 V DC, 1 s
SIPART PS2
Accessory modules
Without Ex protection
With Ex protection
Explosion protection to EN 50014 and

EN 50020
II 2G EEx ia/ib II C T4/T5/T6
II 3G EEx nA L [L] II C T6
Mounting location
Zone 1
Zone 2
Electrical data
Permissible ambient temperature for oper- -30 ... +80 C (-22 ... +176 F)
ation
(For devices with Ex protection: Only in
conjunction with the basic device
6DR5... -.E.... Only T4 is permissible when
using Iy module. )
T4: -30 ... +80 C (-22 ... +176 F)

T5: -30 ... +65 C (-22 ... +149 F)
T6: -30 ... +50 C (-22 ... +122 F)
Iy module
6DR4004-8J (without Ex protection)
6DR4004-6J (with Ex protection)
6DR4004-6J (with Ex protection)
DC output for position feedback
2-wire connection
2-wire connection
2-wire connection
Nominal signal range i
4 ... 20 mA, short-circuit-proof
Total operating range
3.6 ... 20.5 mA
3.6 ... 20.5 mA
3.6 ... 20.5 mA
Power supply UH
+12 ... +35 V
+12 ... +30 V
+12 ... +30 V
External load RB [kW]
(UH [V] - 12 V) /i [mA]
(UH [V] - 12 V) /i [mA]
(UH [V] - 12 V) /i [mA]
Transmission error
0.3%
0.3%
0.3%
Temperature effect
0.1%/10 K ( 0.1%/18 F)
0.1%/10 K ( 0.1%/18 F)
0.1%/10 K ( 0.1%/18 F)
Resolution
0.1%
0.1%
0.1%
Residual ripple
1%
1%
1%
11 nF
Negligible
Intrinsically safe: Ui 30 V DC
Ii 100 mA; Pi 1 W (only T4)
Ui 30 V DC
Ii 100 mA; Pi 1 W (only T4)

Electrically isolated from the

basic device

basic device

basic device
Test voltage
840 V DC, 1 s
840 V DC, 1 s
840 V DC, 1 s
NCS sensor
(not for EEx d version)
Position range
Linear actuator
3 ... 130 mm (0.12 ... 5.12 inch), 3 ... 130 mm (0.12 ... 5.12 inch), 3 ... 130 mm (0.12 ... 5.12 inch),
to 200 mm (7.87 inch) on request to 200 mm (7.87 inch) on request to 200 mm (7.87 inch) on request
Part-turn actuator
30 ... 100
Linearity (after correction by SIPART PS2)

Linear actuator
1%
Part-turn actuator
1%
30 ... 100
30 ... 100
1%
1%
1%
1%
Hysteresis
0.2%
0.2%
0.2%
Continuous working temperature
-40 ... +85 C (-40 ... +185 F),

extended temperature range on
request
-40 ... +85 C (-40 ... +185 F),

request
-40 ... +85 C (-40 ... +185 F),

request
Degree of protection of casing
IP68/NEMA 4x
IP68/NEMA 4x
IP68/NEMA 4x
Siemens FI 01 2005
6/15
SIPART PS2
Dimensional drawings
29.5 29.5
(1.16) (1.16)
72 (2.83)
95 (3.74)
99 (3.89)1)
50 x 4 (1.97 x 0.16) x M6
182 (7.17)
29.5
(1.16)
59 (2.32)
50 x 4 (1.97 x 0.16) x M6
95 (3.74)
All air
11.2 (0.44)
connections
G 1/4 or 1/4 NPT
182 (7.17)
96.6 (3.80)
97 (3.82)1)
All air
connections
11.2 (0.44)
G 1/4 or 1/4 NPT
M20 x 1.5
1) For stainless steel version only
Plastic and stainless steel casing (top), aluminium casing (center), plastic and metal casing (bottom), dimensions in mm (inch)
0GHHS[

00 RU
137[

Flameproof casing left, dimensions in mm (inch)

h9
Siemens FI 01 2005

&RQQHFWLRQ<RQO\IRUGRXEOHDFWLRQYHUVLRQ

6/16

0GHHS[
(

<

DOODLUFRQQHFWLRQV
*RU137

0GHHS[

SIPART PS2
Electric connection of 2-, 3- and 4-wire device (6DR52.. and
6DR53..)
Mounting level of positioner
Devices of types 6DR52.. and 6DR53.. can be operated in a 2-,

3- and 4-wire system.
25 (0,98)
M6
4 +0,1 (0.16+0.04)
12
(0.47)
4
(0,16)
>4 mm
(0.16)
Mounting plate
+
I
*) R 250 W if req.
I H+
i y = 4 to
20 mA
Part-turn actuator
IW
35 (1.38)
2
3
4
5
6
7
8
HART
modem
PC/Laptop
SIPART PS2 electropneumatic positioner, example of connection for communication through HART for 6DR52..
6,
*) Only required with current sources not conforming to HART
Two-wire system
F05-Lkr.-
50 (1.97)
+
Mounting onto part-turn actuators; mounting plate (scope of delivery of

actuator manufacturer), extract from VDI/VDE 3845, dimensions in mm
(inch)
4 ... 20 mA
Schematics
_
Electric connection of 2-wire devices (6DR50.. and 6DR51..)

Devices of types 6DR50.. and 6DR51.. are operated in a 2-wire
system.
Two-wire system
J
4 ... 20 mA
+
_
2
3
4
5
6
7
8
9
BE1
10
Three-/Four-wire system
6
7
8
9
BE1
10
+
18 ... 30 V
_
*)
SIPART PS2 electropneumatic positioner, input circuit for 6DR50.. and

6DR51..
Electric connection of PROFIBUS PA device (6DR55..) and

Foundation Fieldbus devices (6DR56..)
+
0/4 ...
20 mA _
2
3
4
5
6
7
8
9
BE1
10
*) Jumper between 5 and 7 only for three-wire system

+
30 V
+
PROFIBUS-PA and
FOUNDATION fieldbus connection
24 V
81
82
*)
SIPART PS2 electropneumatic positioner, input circuits for 6DR52..
6
7
9
10
+3 V
BE1
*) Input for safety shutdown (activated using coding jumper)
SIPART PS2 PA and SIPART PS2 FF electropneumatic positioner, input

circuit for 6DR55.. and 6DR56..
Siemens FI 01 2005
6/17
SIPART PS2
Selection and Ordering Data
Order No.
Order No.
SIPART PS2, PS2 PA und PS2 FF

electropneumatic positioner
6 DR 5 777 - 0 7777 - 77A7
SIPART PS2, PS2 PA und PS2 FF

electropneumatic positioner
6 DR 5 777 - 0 7777 - 77A7
Design
Two-wire
without HART (4 to 20 mA)
}
with HART, without explosion protec-}
tion (except EEx d)
Two-wire, three-wire, four-wire
with HART, with explosion protection}
without HART, without explosion pro-}
tection
PROFIBUS PA connection
Foundation Fieldbus connection
For actuator
single-action
double-action
}
}
Housing
Plastic
}
Aluminium; only single-action
}
Stainless steel; not for EEx d version: }
not FM/CSA
Aluminium; EEx d casing (flameproof)1)
Explosion protection
Without
}
With explosion protection EEx ia/ib or
EEx d (CENELEC/FM/CSA)1)
With explosion protection EEx n
(CENELEC)
Connection thread
electric/pneumatic
M20 x 1,5 / G1/4
1/2 NPT / 1/4 NPT
M20 x 1,5 / 1/4 NPT
1/2 NPT / G1/4
M25 x 1,5 / G1/4 (EEx d version
only)1)
With PROFIBUS plug M12 / G1/4
With PROFIBUS plug M12 / N1/4
VDI/VDE 3847
Option modules
built-in, incl. 2nd cable gland
Without
Siemens FI 01 2005
0
1
Instruction manual
German/English
French/Spanish/Italian
2
3
Attached gauge block assembly

Without
A
B
5
6
1
2
} Available ex stock
1
) without cable gland
0
1
2
Order No.
Accessories
NCS sensor
for non-contacting detection of position
(not with EEx d version), cable length 6 m
(19.68 ft)
6 D R 4 00 0 4 - 7 N N 7 0
N
E
Without explosion protection
With explosion protection
for part-turn actuators
for linear actuators up to 14 mm (0.55 inch)
for linear actuators >14 mm (0.55 inch), up

to 130 mm (5.12 inch) with standard mounting kit
An EMC filter module for the controller unit
is also required.
(separate ordering data see next page)
G
N
M
P
Q
R
S
V
Limit monitor
built-in, incl. 2nd cable gland
Without
6/18
Customer-specific design
Without
SIPART PS2
Order No.
Accessories
Alarm module for 3 alarm outputs and 1 binary input (functionality: 2 limit monitors, 1 fault
alarm, 1 binary input)
- Without explosion protection }
- With explosion protection
}
- CENELEC 1)
SIA module (slot-type initiator
alarm module, not for 6DR4 version and not for EEx d version)
- Without
- With
Iy module for position feedback
signal (4 to 20 mA)
}
- CENELEC
HART module (only for 6DR400
version)
}
- CENELEC
HART modem for connecting to }
PC or laptop for 6DR40... and
6DR5...
Mounting kit for NAMUR partturn actuators
(VDI/VDE 3845, without mounting }
plate)
The following mounting plates
can be used with the NAMUR
part-turn actuator mounting kit
6DR4004-8D.
Size W x L x H (H = height of shaft
butt)
30 x 80 x 20 mm
}
30 x 80 x 30 mm
}
30 x 130 x 30 mm
}
30 x 130 x 30 mm
}
Mounting kit for other part-turn
actuators
The following mounting plates
can be used together with the
NAMUR part-turn actuator mounting kit 6DR4004-8D.
SPX (DEZURIK) Power Rac,
}
sizes R1, R1A, R2 and R2A
Masoneilan Camflex II
}
Fisher 1051/1052/1061, sizes }
30, 40, 60 to 70
Fisher 1051/1052, size 1033
}
Mounting kit for NAMUR linear
actuators
NAMUR linear actuator
}
mounting kit with short lever
arm (2 to 35 mm)
Lever arm for travels from 35 mm }
to 130 cm (1.38 inch to
5.12 inch)
Reduced mounting kit for linear }
actuator (without fixing angle
and U-bracket), with short lever
with up to 35 mm travel
(1.38 inch)
Reduced mounting kit for linear }
actuator (without fixing angle
and U-bracket), with long lever
with >35 mm travel (1.38 inch)
6DR4004-8A
6DR4004-6A
6DR4004-7A
6DR4004-8G
6DR4004-6G
6DR4004-8J
6DR4004-6J
6DR4004-7J
6DR4004-8H
6DR4004-6H
6DR4004-7H
7MF4997-1DA
6DR4004-8D
TGX:16152-105
TGX:16152-147
TGX:16300-149
TGX:16300-151
TGX:16152-328
TGX:16152-350
TGX:16152-364
TGX:16152-348
6DR4004-8V
6DR4004-8L
6DR4004-8VK
6DR4004-8VL
Mounting kit for other linear

actuators
Retrofitting kit for Moore series }
72 and 750 valve positioners
Fisher type 657/667, size 30
}
to 80
SAMSON actuator type 3277 }
(yoke dimension (H5) =
101 mm 2) (integrated connection without tube)
Pipe mounting
Mounting bracket for pipe mount- }
ing of the SIPART PS2 position
(e.g. when using the NCS sensor)
TGX:16152-117
TGX:16152-110
6DR4004-8S
TGX:16152-117
Mounting kit to VDI/VDE 3847

SIPART PS2 mounting block for }
single-action actuators, incl.
mounting material
SIPART PS2 mounting block for }
double-action actuators, incl.
mounting material
Mounting block for actuator, for }
mounting on IEC 534-6 interface
(NAMUR yoke), incl. mounting
material and mounting kit
6DR4004-8VK
VDI/VDE 3847 adapter block for }
part-turn actuators (to NAMUR
3847)
6DR4004-8CE
6DR4004-8CD
6DR4004-8CA
On request
Additional actuator items can be

found at the following Internet
address:
www.siemens.com/sipartps2
Customer-specific actuators available on request.
Pressure gauge block including
pressure gauge
For single-action SIPART PS2
positioner (2 pressure gauges,
scaled in MPa and bar)
For double-action SIPART PS2
positioner (3 pressure gauges,
scaled in MPa and bar)
Connection block, for safety
solenoid valve with extended
mounting flange to NAMUR
For mounting to IEC 534-6
6
6DR4004-1M 3)
6DR4004-2M 3)
6DR4004-1B
For SAMSON actuator (integrated mounting) see above
6DR4004-1C 4)
Rating plate set Ex n (for

6DR400.-.E) for conversion to
Ex n mode approval (zone 2)
C73451-A430-D55
External position detection system (with explosion protection to

CENELEC) for separate mounting of position sensor and controller (for for EEx d version),
comprising SIPART PS2 plastic
casing with integral potentiometer
and sliding clutch (without electronics and valve block)
For the CE marking, the EMC filter
module is additionally required for
the controller unit.
(separate ordering item below)
C73451-A430-D78
EMC filter module for connection

of external position sensor
(10 k) (not for EEx d version)
C73451-A430-D23
} Available ex stock.
1) U.S. certification by FM institute
2) With a yoke dimension H5 = 95 mm, only the SIPART PS2 in a metal casing can be used.
3) 1MN or -2MN with NPT thread, scaled in MPa and psi.
4) Only together with 6DR4004-8S and 6DR4004-1M.
Siemens FI 01 2005
6/19
SIPART PS2
Documentation
Instruction Manual SIPART PS2
German/English
French/Italian/Spanish
A5E00074600
A5E00074601

PROFIBUS PA
German/English
French/Italian/Spanish
A5E00120716
A5E00120717
Instruction Manual NCS Sensor

German/English/French/
Spanish/Italian
A5E00097485
Manual for SIPART PS2/

PS2 EEx d (6DR5xxx)
German
English
A5E00074630
A5E00074631
Manual for SIPART PS2

PROFIBUS PA
German
English
A5E00127924
A5E00127926

EEx d
German/English
A5E00165376

EEx d PA
German/English
A5E00165378
SITRANS I outgoing isolator

HART (see "SITRANS I supply
units and input isolators") with
24 V DC power supply
230 V AC power supply
7NG4130-1AA11
7NG4130-1BA11
Note
All the above mentioned manuals are included on CD-ROM or
can be downloaded from the Internet.
Following manuals are available in addition as downloads from
the Internet or are included on CD-ROM:
Instruction Manual SIPART PS2 FF, Electropneumatic Positioner (6DR56xx) with Foundation Fieldbus
- German/English: A5E00214570
Instruction Manual SIPART PS FF, Electropneumatic Positioner
(6DR56xx) with Foundation Fieldbus
- German: A5E00214568
- English: A5E00214569
6/20
Siemens FI 01 2005
SIPART PS2
Scope of delivery for positioner
More infomation
1 SIPART PS2 positioner as ordered

1 CD-ROM with the complete documentation for all versions
and accessories
1 each "SIPART PS2 Configuring Instructions - a concise overview" in German and English
Training
Scope of delivery for mounting kit 6DR4004-8V

(for linear actuators)
1 mounting bracket
2 mounting prisms
1 U-bracket
1 lever arm with adjustable pick-up roll
2 U-bolts
Various screws and lock washers
On request
Refer to Catalog ITC for details of training courses for these devices.
Special versions
Scope of delivery for mounting kit 6DR4004-8D

(for part-turn actuators)
1 coupling wheel
1 driver pin
8 scales
1 pointer
Various screws and lock washers
Note: The mounting consoles and the screws for mounting onto
the part-turn actuator are not included in the scope of delivery
and must be provided by the customer (see Technical data).
Siemens FI 01 2005
6/21
SIPART PS2
Mounting of SIPART PS2 on linear actuators
6/22
Siemens FI 01 2005
Mounting of SIPART PS2 on part-turn actuators
SIPART PS2
Mounting of SIPART PS2 EEx d on linear actuators
Mounting of SIPART PS2 EEx d on part-turn actuators
Siemens FI 01 2005
6/23

SIEMENS Catalouge

Uploaded by

Copyright:

Available Formats

SIEMENS Catalouge

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SIEMENS Catalouge

Uploaded by

Copyright:

Available Formats

Electropneumatic positioners

SIPART PS2 electropneumatic positioner

SIPART PS2 EEx d electropneumatic positioner in flameproof casing

The SIPART PS2 positioner is available:

SIPART PS2 or SIPART PS2 in stainless steel casing

The SIPART PS2 electropneumatic positioner is used to control

A non-intrinsically-safe application is permissible in zone 1 for

The use of linear potentiometers is recommendable for very

Separate connection of actuator travel detection system and controller

Non-contacting position sensor (NCS)

Alarm module (3 outputs, 1 input)

When operating the SIPART PS2 through the HART interface,

Motherboard with microcontroller and input circuit

SIPART PS2, electropneumatic positioner, function diagram

7 SIA module (slot initiator alarm module)

SIPART PS2 (all versions)

3 ... 130 mm (0.12 ... 5.12 inch)

Angle of rotation (part-turn actuators)

Using attachment set

Binary input BE1 (terminals 9/10;

Suitable only for floating contact;

Any; pneumatic connections and

Conformity as regards EMC

EN 61326/A1 Appendix A.1 and

3.5 mm (0.14 inch), 2 ... 27 Hz

150 m/s (492 ft/s), 6 ms,

Noise (digitally controlled)

10 ... 200 Hz; 1 (m/s)/Hz

98.1 m/s (321.84 ft/s),

200 ... 500 Hz; 0.3 (m/s)/Hz

30 m/s ( 98.4 ft/s) without resonance sharpness

Weight, basic device

Approx. 0.9 kg (0.90 kg)

See Dimension drawing

Climate class to DIN EN 60721-3-4 To IEC 721

1K5, but -40 ... +80 C

2K4, but -40 ... +80 C

4K3, but -30 ... +80 C

Certificate and approvals

1.4 ... 7 bar (20.3 ... 101.5 psi):

Air quality to ISO 8573-1

Pressure dew point

Class 2 (min. 20 K (36 F) below

4.1 Nm/h (18.1 USgpm)

Outlet air valve 3)

8.2 Nm/h (36.1 USgpm)

< 610-4 Nm/h (0.0026 USgpm)

Power consumption in the controlled state

< 3.610-2 Nm/h (0.158 USgpm)

Single-action and double-action

1) During commissioning at 0 C ( 32 F) make sure that the valves are

-30 ... +80 C

T4: -30 ... +80 C (-22 ... +176 F)

Current to maintain the power supply

Required load voltage

Without HART (6DR53..)

With HART (6DR51..)

With HART (6DR52..)

Static destruction limit