Scribd Logo
Upload

Welcome to Scribd!

  • 374 views

    DIGISOL-RANGER Series-DG-BR4000NEWireless Repeater With Router DG-BG4100N

    Uploaded by

    moseschitturi
    Configuring of Digisol repeaeter

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    DIGISOL-RANGER Series-DG-BR4000NEWireless Repeater With Router DG-BG4100N

    Uploaded by

    moseschitturi
    374 views10 pages
    Configuring of Digisol repeaeter

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Configuring of Digisol repeaeter

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    374 views10 pages

    DIGISOL-RANGER Series-DG-BR4000NEWireless Repeater With Router DG-BG4100N

    Uploaded by

    moseschitturi
    Configuring of Digisol repeaeter

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 10

    V1.

    0
    2013-02-04


    RANGER SERIES
    DG-BR4000N/E
    Setup Guide :
    Internet browsing on smartphones
    (This Guide applies to all Hardware Versions of DG-BG4011N)
    SETUP GUIDE
    Wireless Repeater Mode
    (DG-BG4100N is the Main router and DG-BR4000N/E acts as a
    wireless repeater)
    SETUP GUIDE Wireless Repeater Mode





    COPYRIGHT
    Copyright 2013 by Smartlink Network Systems Ltd. All rights reserved. No part of this publication
    may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
    language or computer language, in any form or by any means, electronic, mechanical, magnetic,
    optical, chemical, manual or otherwise, without the prior written permission of this company This
    company makes no representations or warranties, either expressed or implied, with respect to the
    contents hereof and specifically disclaims any warranties, merchantability or fitness for any
    particular purpose. Any software described in this manual is sold or licensed "as is". Should the
    programs prove defective following their purchase, the buyer (and not this company, its distributor,
    or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or
    consequential damages resulting from any defect in the software. Further, this company reserves
    the right to revise this publication and to make changes from time to time in the contents thereof
    without obligation to notify any person of such revision or changes.

    Trademarks
    DIGISOL is a trademark of Smartlink Network Systems Ltd. All other trademarks are the property
    of the respective manufacturers.











    SETUP GUIDE Wireless Repeater Mode




    DG-BR4000N/E can be configured in Repeater mode with ADSL Router DG-BG4100N.
    Network devices used in this setup:
    DG-BR4000N/E
    DG-BG4100N
    Wireless Laptop
    Network Setup:
    In the Following setup, DG-BG4100N (Main Router) is connected to Internet using the ADSL Connection.
    We are connecting DG-BR4000N/E (Repeater) to extend the wireless range of the Main Router i.e. DG-
    BG4100N.



    Access the web GUI of the router. The default IP of the router is 192.168.1.1 and the user name is
    admin and password is admin.
    Click on Network > WLAN on the top and Basic on the left hand side. Select the Mode to
    AP+WDS.
    NOTE: Ensure that the channel number is set to some fixed value. In this setup it is set to channel
    number 11.
    Step 1 : Configure the ADSL Router
    SETUP GUIDE Wireless Repeater Mode




    Click Apply Changes to save the settings.



    Click on Network > WLAN on top and then WDS on the left hand side. Select the check box Enable
    WDS and enter the Wireless MAC Address of DG-BR4000N/E as shown in below figure. Click Apply
    Changes to save the settings.

    Step 2 : Enable WDS in DG-BG4100N
    SETUP GUIDE Wireless Repeater Mode





    Click on Network > WLAN on top and then WDS Security on the left hand side. Select the
    Encryption to WEP and enter a Pre-Shared Key. In this example we enter the key as 0123456789.
    Click Apply Changes to save the settings.












    Step 3 : Configure the Wireless security for DG-BG4100N
    SETUP GUIDE Wireless Repeater Mode





    Access the web GUI of the router, default IP is 192.168.2.1 and the username is admin and the
    password is 1234.
    If the router IP is default then we need to change it to some other IP other than the DG-BG4100N IP
    address. In the following screen, we will assign an IP 192.168.1.100 to the router. Click Apply to save
    the settings.

    Now, login to the router using the new IP address. In this setup it is 192.168.1.100.









    Step 4 : Configure the DG-BR4000N/E LAN IP address
    SETUP GUIDE Wireless Repeater Mode





    To configure the wireless settings on the router, click on Wireless Settings > Wireless Basic Settings.
    Configure the desired SSID and then set the Channel to one which is configured on DG-BG4100N. In
    this setup the channel on DG-BG4100N was set to 11, hence we will set the same channel on router.

    In the same page, select the Security Option to WEP and enter the same Pre-shared kay as enterned in
    the router DG-BG4100N.

    Step 3 : Configure the Wireless Settings on DG-BR4000N/E
    SETUP GUIDE Wireless Repeater Mode




    Click Apply to save the setting.


    Click on the Wireless Settings > Wireless Repeater. Select the check box for Enable Wireless
    repeater and then select the Radio Button for Wireless Repeater.

    The Repeater IP Address should be set to its own IP address i.e. DG-BR4000N/E LAN IP Address. In this
    set up the router IP is 192.168.1.100, hence the same is entered here. The Base Station MAC Address
    should be the Wireless MAC Address of DG-BR4100N.
    Click Apply to save the settings.
    The DG-BG4100N and DG-BR4000N/E configuration is now complete. You can now connect a wireless
    client to DG-BR4000N/E then then ping to the DG-BG4100N LAN IP i.e 192.168.1.1.





    Step 4 : Configure the Wireless Repeater settings on DG-BR4000N/E
    SETUP GUIDE Wireless Repeater Mode




    Verification:
    On the wireless client seach for the wireless network and select and connect to 4000NE SSID. Once
    connected then ping to the LAN IP of DG-BR4000N/E i.e 192.168.1.100. If you get reply then ping to
    192.168.1. 1 i.e. the IP address of DG-BG4100N.







    Wireless Client Connect to DG-
    BR4000N/E SSID i.e. 4000N/E
    Wireless Client can ping to
    the DG-BR4000N/E LAN IP
    wirelessly i.e. 192.168.2.2
    Wireless Client can
    ping to DG-BG4100N
    IP wirelessly i.e.
    192.168.1.1
    SETUP GUIDE Wireless Repeater Mode

    You might also like