MEPFSGEN

Pall Polypropylene Filters

Selection Guide
1
Determining Operating Conditions
Selecting the appropriate filter requires knowledge of the application parameters.
The following information is required to guide the user.
1. Define the fluid
Type of fluid to be filtered: Gas Liquid (aqueous) Liquid (solvent)
Name of fluid to be filtered: _____________________________________________________________
Name of solvent (if the fluid to be filtered is solvent-based) __________________________________
Presence/absence of solid content: Suspension (e.g.,slurry) Solution
Viscosity: ______________________________ mPaS
pH: ______________________________
Temperature
1
: ______________________________
Pressure
2
: ______________________________ MPa kg/cm
2
Note:
1
The maximum operating temperature for polypropylene is 80 /176. Contact Pall for higher temperature options.
2
The temperature and pressure of the gas to be filtered is required to determine the standard volume.
2. Determine the required removal rating
Removal rating: Nominal m Absolute m
In-service filter: Existing N/A
Filter part no.: _______________________________________________________________________
Note:
Determine the need for an absolute or nominal rating. If the removal rating of the current filter or a filter
used in a similar application is unknown, note the part number and contact Pall.
3. Determine the flow rate
Liquid flow rate: L m
3
/ minute hour batch
For batch filtration, processing time: ________________ minute hour
2
Select the Filter Medium and Configuration
Select the appropriate medium from the selection chart below, using the type of fluid to be filtered
(viscosity, solids concentration) and removal ratings as a guide. If the fluid to be filtered is not listed, select
the filter medium and configuration recommended for a similar type of fluid.
Pleated Type
Process water, Air
HDC

Poly-Fine

Depth Type
Abrasives, Slurries
Profile

Nexis

NXA
Nexis

NXT
Claris

Pleated Depth Type

Gel removal from high-viscosity liquids
High-viscosity slurries and pastes
Profile

UP
Poly-Fine

XLD
Profile

Star
Media Configurations
3
Characteristics of Polypropylene Media and
Applications
Depth Media
Depth filters are constructed by depositing fibrous material onto a rotating center core and forming a tapered pore structure.
Four types of products are available.
Profile

Filter
The Profile II filter cartridge is an absolute rated
depth filter. This all-polypropylene filter has a
continuously graded pore structure for built-in
prefiltration and long service life.
Applications
These filters are the ideal choice for filtering
polishing slurries used for the following
applications; chemical mechanical planarization
(CMP); hard disk drive (HDD) and bulk wafer
polishing. Profile II filters are recommended for
applications requiring the removal of particles
below 5 microns.
Nexis

A Series Filter
The Nexis A filter cartridge is a more economical
absolute rated depth filter. This all-polypropylene
filter features proprietary CoLD (Co-located Large
Diameter) fiber technology to enhance the filters
strength and minimize contaminant unloading.
In addition, this filter has been optimized with a
graded pore structure for outstanding dirt holding
capacity and long service life.
Applications
These cartridges are suitable for filtering, slurries
and high viscosity liquids such as coatings
containing various suspended solids. Nexis A
Series filters offer highly cost effective
performance for applications requiring an
absolute rated filter to remove particles 5 microns
and larger.
Nexis

T Series Filter
The Nexis T filter cartridge is a nominally rated
depth filter. This all-polypropylene filter features
proprietary CoLD (Co-located Large Diameter)
Melt fiber technology to enhance the filters
strength and resist contaminant unloading. In
addition, this filter has been optimized with a
graded pore structure for outstanding dirt holding
capacity and long service life. Nexis T filters are
available in a wide range of nominal micron
ratings from 0.5 micron to 200 microns.
Applications
These filters are the ideal choice to replace string
wound filters for improved and economical
filtration. in high-viscosity fluids, cooling water
and plating solutions.
Tapered Pore Structure
CoLD Melt
TM
Fiber Structure
Claris

Series Filter
The Claris filter cartridge is a nominally rated,
depth filter that utilizes an extruded core made
from very dense fibers. It is Palls most
economical, depth filtration product.
Claris filters are available in a wide range of
nominal ratings from1 to 75 microns.
Applications
These filters are widely used for filtering large
volumes of liquid such as water in swimming
pools, non-critical process water and chemicals
in the photovoltaic industry.

Constant pore
final filter layer
Continuously graded pore
prefilter layer
Support
fiber
Filtration
fiber
Heat
sealed
4
Profile

Star Filter
The Profile Star filter is an all-polypropylene,
pleated-depth filter that combines the exceptional
dirt-holding capacity of depth filters with the high
flow rates of pleated filters. While the Profile Star
filter has a pressure drop and flow capability
comparable to many competitive, pleated, non-
depth polypropylene filters, it excels in the removal
of such contaminants as gels and agglomerates.
Applications
These filters are the ideal choice for filtering both
high-concentration slurries and high-viscosity
pastes, where fine dispersion classification and gel
removal are required. A highly successful
application for Profile Star series, is filtering color
resists used in the manufacture of LCD color filters.
Profile

UP Filter
The Profile UP filter is an innovative combination
of depth and pleated filtration technologies. This
all-polypropylene product consists of a pleated,
depth medium using the Ultipleat

filter geometry
for high effective filtration area. The result is a
filter having superior flow rates with very low
differential pressures.
Applications
Because of their pleated depth structure and very
high flow capabilities, Profile UP filters are
recommended for a wide range of fluids, with
varying viscosities and solids concentrations.
Poly-Fine

XLD Filter
The Poly-Fine XLD filter combines the best
attributes of depth and pleated filtration
technologies. This allpolypropylene product
combines the high flow capacity and low pressure
drop of pleated filters, with the gel retention
capability and long life of a depth filter. The multi-
layer media structure has been developed for fine
dispersion classification and gel retention.
Applications
These filters are the ideal choice for the filtration
of high-viscosity and high-concentration slurries
where a more cost effective solution is required.
Pleated-Depth Media
Pleated depth filters are formed using a pleated cylinder made of thick filter media with a tapered pore
structure. Three types of filters with different pleated cylinder structures are available.
HDC

Filter
The HDC II filter cartridge is a high filtration area,
all-polypropylene pleated cartridge exhibiting very
low differential pressures. Unlike other
polypropylene pleated filters, the HDC cartridge
utilizes a proprietary medium construction
composed of a continuously varying fiber diameter
to produce a pore size distribution from coarse
(upstream) to fine (downstream). This unique
construction permits more contaminants to be
trapped in the outer layers of the medium, thus
substantially increasing dirt-holding capacity.
Applications
These filters are the ideal choice for process water
and air where very high flow rates are required. HDC II
filters are especially recommended for the removal of
liquid particles below 5 micron or airborne particles
below 0.1 micron.
Poly-Fine

Filter
The Poly-Fine II filter cartridge has a pleated
construction, providing for very low pressure drops
and high flow rates. This most economical pleated,
polypropylene product comes in a range of
removal ratings from 0.45 to 200 microns.
Applications
These filters are the ideal choice for process water
and air when a more cost effective solution is required.
Pleated Media
Pleated filters are formed using a pleated cylinder made of polypropylene filter media. Two types of products
made with different filter media are available.
5
Table 1
DFA
TM
Filter Assembly
(HDC II, Profile Star)
PDF Filter Assembly
(Poly-Fine II, Nexis A, Nexis T)
*Single open end/Double open end and 254-762 mm / 10-30 inch size are available in all filter media.
Junior style 4463 series is availbale in HDC II only.
Filter Configurations Selection and Sizing Guide
(Standard Cartridges and Capsules) - Table 1
After selecting the most suitable filter medium, determine the size and number of filters required based on
the configurations and sizing selection chart below. For pressure drop values, refer to the relevant data
sheet. The recommended flow rate indicated below is provided as a guideline to optimize filter life.
5
254 mm
10 inch
508 mm
20 inch
762 mm
30 inch
10
30
45
50
70
90
110
51 mm
2 inch
102 mm
4 inch
4463 Series
Capsule/Junior Cartridge
Maximum Liquid Flow Rate
Recommended Liquid Flow Rate
Double Open End Single Open End
For flow rates above 90 L/min, increase the number of
cartridges to be used in parallel or refer to Table 2 (large type cartridge).
F
l
o
w

R
a
t
e

p
e
r

C
a
r
t
r
i
d
g
e

(
L
/
m
i
n
)
Cartridge Capsule
Junior style 4463 Series (102 mm / 4 inch)
Double Open End, Gasket Type
Single Open End, O-Ring Type
6
Table 2
Filter Configuration Selection and Sizing Guide
(Large Flow Cartridges) - Table 2
Pall large flow cartridges are designed to be very cost effective for flow rates greater than 90 L/min.
The recommended flow rate indicated below is provided as a guideline to optimize filter life.
254 mm
10 inch
508 mm
20 inch
762 mm
30 inch
1524 mm
60 inch
800
600
400
200
2000
1500
1000
190
230
270
300
380
450
660
1300
1900
Marksman
TM
Poly-FineXLD
Maximum Liquid Flow Rate
Recommended Liquid Flow Rate
Marksman Poly-FineII Ultipleat High Flow
F
l
o
w

R
a
t
e

p
e
r

C
a
r
t
r
i
d
g
e

(
L
/
m
i
n
)
Marksman
TM
(Poly-Fine XLD, Poly-Fine II)
Ultipleat High Flow
(Profile UP, HDCII)
Large Flow Cartridge
Pall Microelectronics
25 Harbor Park Drive
Port Washington, NY 11050
+1 516 484 3600 telephone
+1 800 360 7255 toll free US
[email protected]
Nihon Pall Ltd.
6--1, Nishishinjuku,
Shinjuku-ku
Tokyo 163-1325 Japan
Phone: +81.3.6901.5710
Fax: +81.3.5322.2109
Visit us on the web at www.pall.com
Pall Corporation has ofces and plants throughout the world. For Pall
representatives in your area, please go to www.pall.com/contact
Because of technological developments related to the products, systems, and/or services
described herein, the data and procedures are subject to change without notice. Please consult
your Pall representative or visit www.pall.com to verify that this information remains valid.
Products in this document may be covered by one or more of the following patent numbers: EP 1
165 205; US 6,342,283; US 6,662,842; US 7,473,360; EP 0 830 191; US 5,591,335; US
5,653,833; US 5,681,469; US 5,690,782; US 5,730,820; US 5,733,581; US 5,741,395; USD
5,783,011; EP 0 982 061; EP 1 380 331; US 5,543,047; US 5,690,765; US 5,725,784;
US 6,113, 784; US 7,083,564; US 7,318.800; EP 0 667 800;
Copyright 2011. Pall Corporation, Pall, Claris, CoLD Melt, DFA, HDC, Marksman, Nexis,
Poly-Fine and Ultipleat are trademarks of Pall Corporation. indicates a trademark registered in
the USA.
is a service mark of Pall Corporation.
Sept 2011 MEPFSGEN