Eq. Divididos 5 A 20 TR Solo Frio R-410

Download as pdf or txt
Download as pdf or txt
You are on page 1of 125

Split System Cooling

Cooling Units
6 to 20 Ton - 60 Hz, R-410A
Air Handlers
5 to 20 Ton - 60 Hz, R-410A

September 2009

SS-PRC028-EN

Introduction

Tranes reputation for providing quality comfort solutions continues with the development of the
next generation Light Commercial Odyssey Split Systems.
With wide network availability, flexible applications, installation ease, built-in reliability and easy
servicing, Odyssey will meet any number of customer applications. Add to that Tranes outstanding
customer service and you have the formula to make Odyssey the clear choice for continued
customer satisfaction.

Wide network availability


A broad distribution network provides owners, maintenance personnel, contractors, etc., the
means to get their hands on equipment when they need it. Whether its an emergency replacement
or a new construction project in its infancy stages, Tranes Odyssey products meet an array of needs
at the right time and right price

Flexible applications
No matter what the application, Odyssey provides the solution. A broad array of models and
tonnages are available with single or dual compressors, single or dual circuits and numerous
accessories. Condensing units can be installed on the ground or on a rooftop along with extended
piping runs, while air handlers can be free discharge on the ground or horizontally suspended with
long duct runs from a ceiling. Should application challenges arise, Odyssey delivers.

Easy to install
Small footprints and low weights combined with factory installed components like TXVs, filter
driers, etc., reduce installation time and cost. Colored and numbered wiring and factory tested
units make Odyssey the right choice.

Built-in reliability
Keeping in mind that productivity only occurs when equipment is operational, Trane has taken the
steps to ensure that Odyssey is up and running. Early indicators such as phase/reversal monitors
and loss of charge protection provide diagnostics which prevent failure and provide years of worryfree service and operation.

Easy to service
When preventive maintenance or service is required, technicians will find efficient access to both
air handlers and condensers. Panels provide complete, easy access coupled with standardized
cabinets in which all components are located in proximity. Odysseys improved design results in
minimum service times and costs.
With these capabilities, Odyssey provides customers high efficiency and superior performance for
the best all-around value in the market today.
2009 Trane All rights reserved

SS-PRC028-EN

Table of Contents
Features & Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Application Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Selection Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Model Number Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
General Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Performance Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Jobsite Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Typical Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Dimensional Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Mechanical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

SS-PRC028-EN

Features & Benefits


Standard Features

5-year Limited Compressor Warranty1

1-year Limited Parts Warranty

Anti-Short Cycle Timer

Colored and Numbered Wiring

Convertible Airflow

Crankcase Heaters

Easy Access Low Voltage Terminal Board (LTB)

Electromechanical or ReliaTel Microprocessor Controls

Filters are Standard on all Units

Foil-Faced and Edge Captured Insulation

High Pressure Control

IAQ Dual Sloped and Removable Drain Pans

Liquid Line Refrigerant Drier

Low Ambient Cooling to 0F on Microprocessor Models2

Low Ambient Cooling to 50F on Electromechanical Models

Low Pressure Control

Belt Drive Motors

Phase Loss/Reversal Monitor

Quick Access Panels

Single Point Power

Single Side Service

Standardized Components

Thermal Expansion Valve

Scroll Compressors

FrostStat - Evaporator Defrost Control (EDC)

Low Voltage Circuit Protection

Compressor Discharge Temperature Limit (DLT)

Options
Note: Refer to Model Number Description for option availability.

Factory Installed Options

ReliaTel Controls (Microprocessor)

Black Epoxy Pre-Coated Coils

Factory or Field Installed Options

LonTalk Communications Interface (LCI)

Hail/Vandal Guards

1
2

Not available for 20 Ton.


Modulating BAYLOAM recommended.

SS-PRC028-EN

Features & Benefits

Field Installed Options

High Static Motor Kit

Low Static Motor Kit

Electric Heaters

Trane Communications Interface (TCI)

Vibration Isolators

Hot Gas Bypass1

Zone Sensor

Thermostat

Low Ambient

Cabinet design ensures water integrity

Ease of Service, Installation and Maintenance

Mixed model build enables fastest in the industry ship cycle times

Outstanding Airflow Distribution

ReliaTel Controls

Unmatched Product Support is one of our finest assets. Trane Sales Representatives are a
Support Group that can assist you with:

Other Benefits

Product
Application
Service
Training
Special Applications
Specifications
Computer Programs and much more

Standard Features
Anti-Short Cycle Timer
Provides a 3 minute minimum ON time and 3 minute OFF time for compressors to enhance
compressor reliability by assuring proper oil return.

Belt Drive Motors


For additional static requirements, Odyssey 5-20
ton units offer standard belt drive motors to meet
and exceed a wide range of airflow needs.

Colored And Numbered Wiring


Save time and money tracing wires and diagnosing
the unit.

SS-PRC028-EN

Head Pressure Control recommended.

Features & Benefits

Compressors
Odyssey contains the best compressor technology
available to achieve the highest possible
performance. Dual compressors perform very well
under part load cooling conditions and system backup applications. Dual compressors are available on
10-20 ton models and allow for efficient cooling
utilizing 2-stages of compressor operation.

Controls ReliaTel or Electromechanical


ReliaTel microprocessor controls provide unit control for heating and cooling utilizing input from
sensors that measure indoor and outdoor temperature and other zone sensors. ReliaTel also
provides outputs for building automation systems and expanded diagnostics. For a complete list
of ReliaTel offerings, refer to the Other Benefits section within the Features and Benefits section
of this catalog. For the simpler job that does not require a building automation system, or expanded
diagnostics capabilities, Odyssey offers electromechanical controls. This 24-volt control includes
the control transformer and contactor pressure lugs for power wiring.

Convertible Units
The units ship in a horizontal configuration. They can
be easily converted to vertical by simply
repositioning the drain pan. Units come complete
with duct flanges so the contractor doesnt have to
field fabricate them. These duct flanges are a time
and cost saver.

Crankcase Heaters
These band heaters provide improved compressor
reliability by warming the oil to prevent migration
during off-cycles or low ambient conditions.

Dual Sloped Drain Pans


Every Odyssey unit has a non-corrosive, removable,
double-sloped drain pan thats easy to clean and
reversible to allow installation of drain trap in two
positions on either side of the unit.

Easy Access Low Voltage Terminal Board


Odysseys Low Voltage Terminal Board is external to
the line voltage electrical cabinet. It is extremely easy
to locate and attach the thermostat wire and test
operation of all unit functions. This is another cost
and time saving installation feature.

Foil-Faced Insulation
All internal air handler surfaces have cleanable foilfaced insulation. All edges are either captured or
sealed to ensure that insulation fibers do not get into
the airstream.

SS-PRC028-EN

Features & Benefits

Frostat
This control utilizes a capillary bulb embedded in the face of the evaporator coil which monitors
coil temperature to inhibit evaporator icing and protect the compressor. Recommended for
applications with low leaving air temperatures, low airflow and/or high latent load applications.

High Pressure Control


All units include High Pressure Control as standard.

Low Ambient Cooling


All Odyssey microprocessor units have cooling capabilities down to 0F as standard.
Electromechanical models have cooling capabilities to 50F as built, or to 0F by adding an optional
low ambient kit.

Low Voltage Connections


The wiring of the low voltage connections to the unit
and the zone sensors is as simple as 1-1, 2-2, and 33. This simplified system makes it easy for the
installer to wire.

Phase Monitor/Reversal Protection


Phase monitor shall provide 100% protection for motors and compressors against problems
caused by phase loss, phase imbalance, and phase reversal. Phase monitors are equipped with an
LED that provides an ON or FAULT indicator.

Quick-Access Panels
Remove a few screws for access to the standardized internal components and wiring.

Single Point Power


A single electrical connection powers the unit.

Single Side Service


Single side service is standard on all units.

Standardized Components
Components are placed in the same location on all Odyssey units. Because of these standardized
components throughout the Odyssey line, contractors/owners can stock fewer parts.

Thermal Expansion Valve with Bypass Check Valves


This feature is standard on all units.

Variety of Options
Factory Installed Options
Note: Refer to Model Number Description or Mechanical Specifications for availability.

Black Epoxy Pre-Coated Coils


The pre-coated coils are an economical option for protection in mildly corrosive environments.

Factory or Field Installed Options


Note: Refer to Model Number Description for option availability.

SS-PRC028-EN

Features & Benefits

LonTalk Communications Interface


The LonTalk communications interface allows
the unit to communicate as a TracerLCI-V
device or directly with generic LonTalk
Network Building Automation System
Controls.

Hail/Vandal Guards
These coil guards shall be either factory or
field installed for condenser coil protection.
This feature protects the condenser coil from
vandalism and/or hail damage. When ordered
factory installed, it also adds additional
shipping protection.

Field Installed Options


Note: Refer to Model Number Description or Mechanical Specifications availability.

Trane Communication Interface (TCI)


This module, when applied with ReliaTel, easily interfaces with Tranes Integrated Comfort
System.

Electric Heaters
Electric heat modules are available in a variety of voltages and capacities.

High/Low Static Motor


Available on many models, this high static motor accessory extends the capability of the standard
unit.

Low Ambient
Provides ability to cool space when outdoor ambient is below 50F. Choice of fan on/off or
modulating control.

Zone Sensors/Thermostats
Available in programmable, automatic and manual styles.

Other Benefits
Airflow Distribution
Airflow is outstanding. Odyssey can replace an older machine with old ductwork and, in many
cases, improve the comfort through better air distribution.

SS-PRC028-EN

Features & Benefits

Easy to Install, Service and Maintain


Because todays owners are very cost-conscious when it
comes to service and maintenance, the Trane Odyssey was
designed with direct input from service contractors. This
valuable information helped to design a product that would
get the service person off the job quicker and save the
owner money. Odyssey offers outstanding standard
features enhanced by a variety of factory and field installed
options, multiple control options, rigorously tested proven
designs and superior product and technical support.

Flexibility
Odyssey offers ultimate flexibility. Units are built to order in
our standard shortest in the industry ship cycle time.

ReliaTel Controls
ReliaTel controls provide unit control for heating and
cooling, utilizing input from sensors that measure outdoor
and indoor temperature.

ReliaTel Control Logic Enhances Quality and


Reliability
prevents the unit from short cycling, considerably
improving compressor life.
ensures that the compressor will run for a specific
amount of time which allows oil to return for better
lubrication, enhancing the reliability of the
compressor.
Odyssey units with ReliaTel reduces the number of
components required to operate the unit, thereby
reducing possibilities for component failure.

ReliaTel Makes Installing and Servicing Easy


ReliaTel eliminates the need for field installed time delay
relays.
ReliaTel controls provide these functions as an integral part of the unit. The contractor no longer
has to purchase these controls as options and pay to install them.
The wiring of the low voltage connections to the unit and the zone sensors is as easy as 1-1, 2-2,
and 3-3. This simplified system makes wiring easier for the installer.

ReliaTel Makes Testing Easy


ReliaTel requires no special tools to run the Odyssey unit through its paces. Simply place a jumper
between Test 1 (T1) and Test 2 (T2) terminals on the Low Voltage Terminal Board and the unit will
walk through its operational steps automatically.
The unit automatically returns control to the zone sensor after stepping through the test mode a
single time, even if the jumper is left on the unit.
As long as the unit has power and the system LED is lit, ReliaTel is operational. The light indicates
that the controls are functioning properly.
ReliaTel features expanded diagnostic capabilities when utilized with Trane Integrated
ComfortSystems.
SS-PRC028-EN

Features & Benefits

Some zone sensor options have central control panel lights which indicate the mode the unit is in
and possible diagnostic information.

Other ReliaTel Benefits


The ReliaTel built-in anti-short cycle timer, time delay relay and minimum on time control
functions are factory tested to assure proper operation.
ReliaTel softens electrical spikes by staging on fans, compressors and heaters.
Intelligent Fallback is a benefit to the building occupant. If a component fails, the unit will continue
to operate at predetermined temperature setpoint.
Intelligent Anticipation is a standard ReliaTel feature. It functions continuously as ReliaTel and zone
sensor(s) work together in harmony to provide much tighter comfort control than conventional
electromechanical thermostats.
The same ReliaTel Board fits all Split System Cooling and Heat Pump models. This provides
standardization of parts for contractors. Less money is tied up in inventory with ReliaTel.

Unit Cabinet
The compact cabinet takes up less room and is less costly to ship.

Rigorous Testing
All of Odysseys designs are rigorously rain tested to ensure water integrity. Actual shipping tests
are performed to determine packaging requirements. Units are test shipped around the country to
determine the best packaging. Factory shake and drop tests are used as part of the package design
process to help assure that the unit arrives at the job site in top condition.
Rigging tests include lifting a unit into the air and letting it drop one foot, assuring that the lifting
lugs and rails hold up under stress. A 100% coil leak test is performed at the factory. The condenser
coils are leak tested at 660 psig and evaporators to 450 psig.
All parts are inspected at the point of final assembly. Sub-standard parts are identified and rejected
immediately. Every unit receives a 100% unit run test before leaving the production line to ensure
it lives up to rigorous Trane requirements.

VariTrac Building Automation System


When Tranes changeover VAV System for light
commercial applications is coupled with
Odyssey, it provides the latest in technological
advances for comfort management systems and
can allow thermostat control in every zone
served by VariTrac.

10

SS-PRC028-EN

Features & Benefits

Available Accessories - TTA/TWE


MODEL

USED WITH

DESCRIPTION

Base (Subbase)
BAYBASE009A

TWE061D/E

BAYBASE010A

TWE090D/E

BAYBASE011A

TWE120D/E

BAYBASE012A

TWE150E, TWE180E

BAYBASE013A

TWE240E

Subbase

Drip Kit
BAYDRKT006A

TWE061D/E

BAYDRKT007A

TWE090D/E

BAYDRKT008A

TWE120D/E

BAYDRKT009A

TWE150E, TWE180E

BAYDRKT010A

TWE240E

Drip Kit

Coil Guard
BAYGARD058A

TTA073D, TTA090D

BAYGARD059A

TTA120D/E/F

BAYGARD060A

TTA150E

BAYGARD061A

TTA180E/F, TTA240E/F

Hail Guard

Return Air Grille


BAYGRLE001A

TWE061D/E

BAYGRLE002A

TWE090D/E

BAYGRLE003A

TWE120D/E

BAYGRLE004A

TWE150E, TWE180E

BAYGRLE005A

TWE240E

Return Air Grille

HOT GAS BY-PASS


BAYHGBP010A

TTA090D - TTA240F

Universal Hot Gas Bypass Kit

BAYHSMT104A

TWE061D1/E1

1.5HP (230/1) w/ 1VL44 motor sheave w/ AK54 fan sheave


w/ A44 belt

BAYHSMT105A

TWE061D3-4/E3-4

1.5HP (230-460/3) w/ 1VL44 motor sheave w/ AK54 fan sheave


w/ A44 belt

BAYHSMT106A

TWE061DW/EW

1.5HP (575/3) w/ 1VL44 motor sheave w/ AK54 fan sheave


w/ A44 belt

BAYHSMT107A

TWE090D1/E1

2 HP (230/1) w/ 1VL44 motor sheave w/ AK66 fan sheave


w/ A50 belt

BAYHSMT108A

TWE090D3/E3

2 HP (230/460/3) w/ 1VL44 motor sheave w/ AK66 fan sheave


w/ A50 belt

BAYHSMT109A

TWE090DW/EW

2 HP (575/3) w/ 1VL44 motor sheave w/ AK66 fan sheave


w/ A50 belt

BAYHSMT110A

TWE090D3/E3

3 HP (230/460/3) w/ 1VP44 motor sheave w/ AK54 fan sheave


w/ AX48 belt

BAYHSMT111A

TWE090DW/EW

3 HP (575/3) w/ 1VP44 motor sheave w/ AK54 fan sheave


w/ AX48 belt

BAYHSMT112A

TWE120D3/E3

3 HP (230/460/3) w/ 1VP44L motor sheave w/ AK74 fan sheave


w/ A51 belt

BAYHSMT113A

TWE120DW/EW

3 HP (575/3) w/ 1VP44L motor sheave w/ AK74 fan sheave


w/ A51 belt

BAYHSMT114A

TWE150E3

3 HP (230/460/3) w/ 1VP44L motor sheave w/ BK72 fan sheave


w/ A51 belt

BAYHSMT115A

TWE150EW

3 HP (575/3) w/ 1VP44L motor sheave w/ BK72 fan sheave


w/ A51 belt

BAYHSMT116A

TWE150E3

5 HP (230/3) w/ 1VP50L motor sheave w/ BK72 fan sheave


w/ BX55 belt

BAYHSMT117A

TWE150E3(a)

5 HP (460/3) w/ 1VP50L motor sheave w/ BK72 fan sheave


w/ BX55 belt

High Static Motor

Continued on next page

SS-PRC028-EN

11

Features & Benefits

MODEL

USED WITH

DESCRIPTION

BAYHSMT118A

TWE150EW

5 HP (575/3) w/ 1VP50L motor sheave w/ BK72 fan sheave w/


BX55 belt

BAYHSMT119A

TWE180E3

5 HP (230/3) w/ 1VP50L motor sheave w/ BK85 fan sheave


w/ BX58 belt

BAYHSMT120A

TWE180E3(a)

5 HP (460/3) w/ 1VP50L motor sheave w/ BK85 fan sheave


w/ BX58 belt

BAYHSMT121A

TWE180EW

5 HP (575/3) w/ 1VP50L motor sheave w/ BK85 fan sheave


w/ BX58 belt

BAYHSMT122A

TWE240E3/4

7.5 HP (230/460/3) w/ 1VP60 motor sheave w/ BK90 fan sheave


w/ BX60 belt

BAYHSMT123A

TWE240EW

7.5 HP (575/3) w/ 1VP60 motor sheave w/ BK90 fan sheave


w/ BX60 belt

Electric Heaters
BAYHTRL106A

TWE061D1-TWE120E1

4.33/5.76 KW Heater 208/240/1 Phase

BAYHTRL112A

TWE061D1-TWE120E1

8.65/11.52 KW Heater 208/240/1 Phase

BAYHTRL117A

TWE061D1-TWE120E1

12.98/17.28 KW Heater 208/240/1 Phase

BAYHTRL123A

TWE061D1-TWE120E1

17.30/23.04 KW Heater 208/240/1 Phase

BAYHTRL129A

TWE061D1-TWE120E1

21.65/28.80 KW Heater 208/240/1 Phase

BAYHTRL305A

TWE061D3-TWE120E3

3.75/5.00 KW Heater 208/240/3 Phase

BAYHTRL310A

TWE061D3-TWE120E3

7.45/9.96 KW Heater 208/240/3 Phase

BAYHTRL315A

TWE061D3-TWE120E3

11.25/14.96 KW Heater 208/240/3 Phase

BAYHTRL325A

TWE061D3-TWE120E3

18.71/24.92KW Heater 208/240/3 Phase

BAYHTRL335A

TWE061D3-TWE120E3

26.20/34.88 KW Heater 208/240/3 Phase

BAYHTRL405A

TWE061D4-TWE120E4

5.00 KW Heater 460/3 Phase

BAYHTRL410A

TWE061D4-TWE120E4

9.96 KW Heater 460/3 Phase

BAYHTRL415A

TWE061D4-TWE120E4

14.96 KW Heater 460/3 Phase

BAYHTRL425A

TWE061D4-TWE120E4

24.92 KW Heater 460/3 Phase

BAYHTRL435A

TWE061D4-TWE120E4

34.88 KW Heater 460/3 Phase

BAYHTRLW05A

TWE061DW-TWE120EW

5 KW Heater 575/3 Phase

BAYHTRLW10A

TWE061DW-TWE120EW

9.96 KW Heater 575/3 Phase

BAYHTRLW15A

TWE061DW-TWE120EW

14.96 KW Heater 575/3 Phase

BAYHTRLW25A

TWE061DW-TWE120EW

24.92 KW Heater 575/3 Phase

BAYHTRLW35A

TWE061DW-TWE120EW

34.88 KW Heater 575/3 Phase

BAYHTRM310A

TWE150E3-TWE240E3

7.50/10.0 KW Heater 208/230 3 Phase

BAYHTRM320A

TWE150E3-TWE240E3

14.96/19.92 KW Heater 208/230 3 Phase

BAYHTRM330A

TWE150E3-TWE240E3

22.50/29.92 KW Heater 208/230 3 Phase

BAYHTRM350A

TWE150E3-TWE240E3

37.42/49.84 KW Heater 208/230 3 Phase

BAYHTRM410A

TWE150E4-TWE240E4

10.0 KW Heater 460/3 Phase

BAYHTRM420A

TWE150E4-TWE240E4

19.92 KW Heater 460/3 Phase

BAYHTRM430A

TWE150E4-TWE240E4

29.92 KW Heater 460/3 Phase

BAYHTRM450A

TWE150EW-TWE240EW

49.84 KW Heater 460/3 Phase

BAYHTRMW10A

TWE150EW-TWE240EW

10.0 KW Heater 575/3 Phase

BAYHTRMW20A

TWE150EW-TWE240EW

19.92 KW Heater 575/3 Phase

BAYHTRMW30A

TWE150EW-TWE240EW

29.92 KW Heater 575/3 Phase

BAYHTRMW50A

TWE150EW-TWE240EW

49.84 KW Heater 575/3 Phase

TTA090D-TTA240F

Comm 3/4 Communications Interface

Trane Communication Interface


BAYICSI003A

Continued on next page

12

SS-PRC028-EN

Features & Benefits

MODEL

USED WITH

DESCRIPTION

Isolators
BAYISLT004A

TTA073D-TTA090D, TWE061D-TWE120E

BAYISLT005A

TTA120D/E/F

BAYISLT009A

TTA150E, TTA180E/F, TWE150E, TWE180E

BAYISLT010A

TTA240E/F, TWE240E

BAYISLT012B

TWE150E, TWE180E

BAYISLT013B

TWE061D/E

BAYISLT014A

TWE090D/E

BAYISLT015B

TWE120D/E

BAYISLT016B

TWE240E

BAYISLT019A

TWE061D/E, TWE090D/E, TWE120D/E

BAYISLT021A

TWE150E, TWE180E

BAYISLT023A

TTA073D, TTA086D, TTA090D, TTA120D

BAYISLT024A

TTA120E/F, TTA150E, TTA180E/F

BAYISLT025A

TTA240E/F

BAYISLT028A

TWE061D/E

BAYISLT029A

TWE090D/E, TWE120D/E

BAYISLT030A

TWE150E, TWE180E

BAYISLT031B

TWE240E

BAYISLT032A

TWE240E

Rubber Isolator Kit

Steel Spring Isolator Kit

Low Ambient
BAYLOAMU01A

TTA073, TTA090A

On/Off Fan Control Mounted in External Enclosure


(small cabinets)

BAYLOAMU02A

TTA120, TTA150, TTA180, TTA240

On/Off Fan Control Mounted in Unit Control Box


large cabinets)

BAYLOAM332A

TTA073D3, TTA090D3

Modulating P-66 Head Pressure Control w/ 208-230V


0.5 HP Hi-Eff Motor (external mount)

BAYLOAM333A

TTA120D3/E3/F3, TTA150E3

Modulating P-66 Head Pressure Control w/ 208-230V


1 HP Hi-Eff Motor (external mount)

BAYLOAM334A

TTA180E3/F3, TTA240E3/F3

Modulating P-66 Head Pressure Control w/ 208-230V


1 HP Hi-Eff Motor (internal mount)

BAYLOAM432A

TTA073D4, TTA090D4

Modulating P-66 Head Pressure Control w/ 460V


0.5 HP Hi-Eff Motor (external mount)

BAYLOAM433A

TTA120D4/E4/F4, TTA150E4

Modulating P-66 Head Pressure Control w/ 460V


1.0 HP Hi-Eff Motor (external mount)

BAYLOAM434A

TTA180E4/F4, TTA240E4/F4

Modulating P-66 Head Pressure Control w/ 460V


1.0 HP Hi-Eff Motor (internal mount)

TWE240E

Low Static Drive Kit

TTA090D-TTA240F

LonTalk Communications Interface

Low Static Drive Kit


BAYLSMT001A

LonTalk Communications Interface


BAYLTCI002B

Continued on next page

SS-PRC028-EN

13

Features & Benefits

MODEL

USED WITH

DESCRIPTION

Plenum
BAYPLNM015B

TWE061D/E

BAYPLNM016B

TWE090D/E

BAYPLNM017B

TWE120D/E

BAYPLNM018B

TWE150E, TWE180E

BAYPLNM019B

TWE240E

BAYPLNM020B

TWE061D/E

BAYPLNM021B

TWE090D/E

BAYPLNM022B

TWE120D/E

BAYPLNM030A

TWE061D/E

BAYPLNM031A

TWE090D/E

BAYPLNM032A

TWE120D/E

BAYPLNM033A

TWE150, TWE180E

BAYPLNM034A

TWE240E

Discharge Plenum & Grille

Hydronic Coil Discharge Plenum & Grille

Electric Heat Discharge Plenum & Grille

Time Delay Relay


BAYRLAY002

TTA090D-TTA240F

Time Delay Relay

BAYTFMR011A

TWE090D3, TWE090E3, TWE120D3, TWE120E3

75va transformer (230V)

BAYTFMR012A

TWE090D4/W, TWE090E4/W, TWE120D4/W,


TWE120E4/W

BAYTFMR013A

TWE075DD, TWE075ED, TWE090DK, TWE090EK,


TWE100DD, TWE100ED, TWE120DK, TWE120EK

Transformer

75va transformer

Water Kits
BAYWATR022A

TWE061D/E

BAYWATR023A

TWE090D/E

BAYWATR024A

TWE120D/E

BAYWATR025A

TWE150E, TWE180E

BAYWATR026A

TWE240E

BAYWATR027A

TWE061D/E

BAYWATR028A

TWE090D/E

BAYWATR029A

TWE120D/E

BAYWATR030A

TWE150E, TWE180E

BAYWATR031A

TWE240E

Steam Coil Enclosure

Hot Water Coil Enclosure

Wire Kit
BAYWRKT002A

TWE061D-TWE120E

180 Blower Discharge Reversal Kit

(a) When used with 460V application.

14

SS-PRC028-EN

Application Considerations
Application of this product should be within the cataloged airflow and performance considerations.

Clearance Requirements
The recommended clearances identified with unit dimensions should be maintained to assure
adequate serviceability, maximum capacity and peak operating efficiency. Actual clearances which
appear inadequate should be reviewed with the local Trane Representative.

180 Blower Rotation


The 5, 7, and 10 ton air handler blower section can be rotated 180 to change the discharge pattern.
This modification must be done in the field and requires an additional kit. See unit installer's guide.

Low Ambient Cooling


As manufactured, electromechanical units can operate to 50 F in the cooling mode of operation.
An accessory head pressure control will allow operation to 0 F outdoor ambient. When using these
units with control systems such as bypass changeover Variable Air Volume, make sure to consider
the requirement for a head pressure control to allow low ambient cooling.
Figure 1. Typical Split System Application

Air Handling
Unit

Split
Condensing
Unit

SS-PRC028-EN

15

Application Considerations

Figure 2. Typical Horizontal Air Handler Application

Isolator (4X)
(Spring or Rubber)
Support Rods and Attaching
Hardware (by others)

Electric Heater
Assembly

Air Handler

Heating Coil &


Enclosure Assembly
(Steam or Hot Water)

Figure 3. Typical Vertical Air Handler Application

Discharge Plenum &


Grille Assembly

Heating Coil &


Enclosure Assembly

Air Handler

Horizontal
Drain

Return-Air Grille

Vertical
Drain
Subbase

Isolators
(Spring or Rubber)

16

SS-PRC028-EN

Selection Procedure
Cooling Capacity
1. Calculate the buildings total and sensible cooling loads at design conditions. Use the Trane
calculation form or any other standard accepted method.
2. Size the equipment using Table 7, p. 26 to Table 17, p. 36. Match the cooling loads at design
conditions.
Example: The following are the building cooling requirements:
a. Electrical Characteristics: 460/60/3
b. Summer Design Conditions:
Entering Evaporator Coil: 80F DB/67F WB, Outdoor Ambient: 95F
c. Total Cooling Load: 86 MBh
d. Sensible Cooling Load: 60 MBh
e. Airflow: 3000 cfm
External Static Pressure: 0.77 inches of water gauge
Table 7, p. 26 shows that TTA090D with TWE090D has a gross cooling capacity of 94.8 MBh and 72.7
MBh sensible capacity at 95F DB ambient and 3000 cfm with 80F DB/67 F WB air entering the
evaporator.
To find the net cooling capacities, fan motor heat must be subtracted. Determine the total unit static
pressure:
External Static: 0.77 in.
Standard Filter: 0.10 in.
Supplementary Electric Heat: 0.23 in.
Total Static Pressure 1.10 in.
Note: The Evaporator Fan Performance Table has included the effect of a 1 in. filter already.
Therefore, the actual Total Static Pressure is 1.10 - 0.10 = 1.00 in.
With 3000 cfm and 1.00 inches, Table 35, p. 54 shows 1.97 Bhp (high static drive kit required).
Note: The formula below the table can be used to calculate Fan Motor Heat:
3.15 X Bhp = MBh
3.15 X 1.97 = 6.2 MBh
Net Total Cooling Capacity = 94.8 MBh - 6.2 = 88.6 MBh
Net Sensible Cooling Capacity = 72.7 MBh - 6.2 = 66.5 MBh

Heating Capacity
1. Calculate the building heating load using the Trane calculation form or any other standard
accepted method.
2. Size the system heating capacity to match the calculated building heating load. The following
are building heating requirements:
a. Total Heating Load: 97.0 MBh
b. 3000 cfm
c. Electric Supplementary Heaters
From Table 47, p. 64, the 34.88 kW heater has a capacity of 119,045 Btuh. From Table 56, p. 78, the
34.88 kW at 460v indicates the heater model number is BAYHTRL435A. This heater will adequately
cover the buildings heating requirement.

SS-PRC028-EN

17

Selection Procedure

Air Delivery Selection


External static pressure drop through the air distribution system has been calculated to be 0.77
inches of water gauge. From Table 46, p. 63 static pressure drop through the electric heater is 0.23
inches of water (0.77 + 0.23 = 1.00 in.). Enter Table 35, p. 54 for TWE090D at 3000 cfm and 1.00 static
pressure. The high static motor at 1020 RPM will give the desired airflow.

18

SS-PRC028-EN

Model Number Description


TTA

240

00

123

456

9 10

11

12

Model Number Description


All products are identified by a multiple-character model number that precisely identifies a
particular type of unit. An explanation of the alphanumeric identification code is provided. Its use
will enable the owner/operator, installing contractors, and service engineers to define the
operation, specific components, and other options for any specific unit.
Note: When ordering replacement parts or requesting service, be sure to refer to the specific
model number, serial number, and DL number (if applicable) stamped on the unit
nameplate.
DIGITS 1 - 3: Product Type
TTA = Split System Cooling

DIGITS 4 - 6: Nominal Gross Cooling Capacity (MBh)


073 = 6 Tons
090 = 7 Tons
120 = 10 Tons
150 = 12 Tons
180 = 15 Tons
240 = 20 Tons
DIGIT 7: Major Development Sequence
D = Single Circuit
E = Dual Circuit
F = Manifold Scroll Compressors
DIGIT 8: Electrical Characteristics
3 = 208-230/60/3
4 = 460/60/3
W = 575/60/3

D = 380-415/50/3
K = 380/60/3

DIGITS 9 - 10: Factory Installed Options


00 = Packed Stock
0S = Black Epoxy Coated Coil
0R = ReliaTel, no LCI Board
0T = ReliaTel, no LCI Board with Black Epoxy Coated Coil
0U = ReliaTel, with LCI Board
0W = ReliaTel, with LCI Board and Black Epoxy Coated Coil
H0 = Hail Guard with Packed Stock
HS = Hail Guard with Black Epoxy Coated Coil
HR = Hail Guard with ReliaTel, no LCI Board
HT = Hail Guard with ReliaTel, no LCI Board with Black Epoxy Coated Coil
HU = Hail Guard with ReliaTel, with LCI Board
HW = Hail Guard with ReliaTel, with LCI Board and Black Epoxy Coated Coil
DIGITS 11: Minor Design Sequence
A & B = Current Design Sequence
DIGITS 12: Service Digit
A = Current Service Digit

SS-PRC028-EN

19

Model Number Description

TWE

240

00

123

456

9 10

11

12

Model Number Description


All products are identified by a multiple-character model number that precisely identifies a
particular type of unit. An explanation of the alphanumeric identification code is provided. Its use
will enable the owner/operator, installing contractors, and service engineers to define the
operation, specific components, and other options for any specific unit.
Note: When ordering replacement parts or requesting service, be sure to refer to the specific
model number, serial number, and DL number (if applicable) stamped on the unit
nameplate.
DIGITS 1 - 3: Product Type
TWE = Split System Heat Pump/Cooling Air Handler
DIGITS 4 - 6: Nominal Gross Cooling Capacity (MBh)
061 = 5 Tons
090 = 7 Tons
120 = 10 Tons
150 = 12 Tons
180 = 15 Tons
240 = 20 Tons
DIGIT 7: Major Development Sequence
D = Single Circuit
E = Dual Circuit
DIGIT 8: Electrical Characteristics
1 = 208-230/60/1
3 = 208-230/60/3
4 = 460/60/3

W = 575/60/3
D = 380-415/50/3
K = 380/60/3

DIGITS 9 - 10: Factory Installed Options


00 = Packed Stock
DIGITS 11: Minor Design Sequence
A & B = Current Design Sequence
DIGITS 12: Service Digit
A = Current Service Digit

20

SS-PRC028-EN

General Data
Table 1.

R-410A Combinations - 60 Hz

TWE061D

TWE061E

See Note

See Note

TWE090D

TWE090E

TTA073D

See Note

TTA090D

TWE120D

TWE120E

TWE150E

TWE180E

TWE240E

TTA090D

TTA120E

(2) TTA073D

TTA180E

(2) TTA120D

TTA150E

TTA180F

(2) TTA120F

TTA120D

(2) TTA090D

TTA180E
TTA240E
TTA240F

Note: See ComfortSite for more information on small outdoor unit combinations.

Table 2.

General Data 6-10 Ton Condensing Units 60 Hz


6 Tons

7 Tons

10 Tons

Dual
Manifolded
Single Compressor Single Compressor Single Compressor
Compressor
Compressor
TTA073D3, D4, DW TTA090D3, D4, DW TTA120D3, D4, DW TTA120E3, E4, EW TTA120F3, F4, FW

Cooling Performance
Gross Cooling Capacity
Matched Air Handler

77,000

94,000

124,000

122,000

123,000

Condensing Unit Only

74,000

90,000

112,000

110,000

114,000

ARI Net Cooling Capacity

75,000

92,000

120,000

119,000

120,000

Efficiency
Matched Air Handler (EER)

11.2

11.2

11.2

11.2

11.2

Condensing Unit Only (EER)

12.5

12.4

12.2

12.2

12.2

System Integrated Part Load Value


(IPLV)

N/A

N/A

N/A

12.0

14.5

System (IEER)

13.0

12.2

12.2

11.7

14.5

Condensing Unit Only (IPLV)

N/A

N/A

N/A

15.9

17.2

6.70/5.92

8.22/7.26

10.72/9.18

10.62/9.01

10.72/9.35

Type

Scroll

Scroll

Scroll

Scroll

Manifolded Scrolls

No./Tons

1/5.6

1/6.9

1/8.6

2/4.2

2/4.3

System kW/Condensing Unit kW

Compressor

System Data
No. Refrigerant Circuits
Suction Line (in.) OD
Liquid Line (in.) OD

Outdoor Coil - Type


Tube Size (in.) OD

1 1/8

1 3/8

1 3/8

1 1/8

1 3/8

1/2

5/8

1/2

1/2

1/2

Lanced

Lanced

Lanced

Lanced

Lanced
0.375

0.375

0.375

0.375

0.375

Face Area (sq ft)

19.2

19.2

24.0

24.0

24.0

Rows/FPI

2/18

2/18

2/18

2/18

2/18

Outdoor Fan - Type

Propeller

Propeller

Propeller

Propeller

Propeller

No. Used/Diameter (in.)

1/26

1/26

1/28

1/28

1/28

Direct/1

Direct/1

Direct/1

Direct/1

Direct/1
9600

Drive Type/No. Speeds


CFM

6530

6530

9600

9600

No. Motor/HP

1/0.5

1/0.5

1/1

1/1

1/1

Motor RPM

1100

1100

1100

1100

1100

15.7

17.6

22.5

24.8

21.2

Refrigerant Charge
(Field Supplied)
(lbs of R410A)

Shipping Dimensions
(HxWxD)

SS-PRC028-EN

43.54 x 43 x 36.5 43.54 x 43 x 36.5

43.49 x 53 x 40.5

21

General Data

Table 3.

General Data 12 - 20 Ton Condensing Units 60 Hz


12 Tons

15 Tons

20 Tons

Dual
Dual
Manifolded
Dual
Manifolded
Compressor
Compressor
Compressor
Compressor
Compressor
TTA150E3, E4, EW TTA180E3, E4, EW TTA180F3, F4, FW TTA240E3, E4, EW TTA240F3, F4, FW
Cooling Performance
Gross Cooling Capacity
Matched Air Handler

154,000

185,000

186,000

263,000

254,000

Condensing Unit Only

144,000

178,000

182,000

270,000

266,000

ARI Net Cooling Capacity

150,000

180,000

180,000

254,000

246,000

Efficiency
Matched Air Handler (EER)

11.0

11.0

11.0

10.0

10.0

Condensing Unit Only (EER)

11.7

12.6

12.8

12.1

12.0

System Integrated Part Load


Value (IPLV)

13.4

13.2

13.4

11.2

12.0

System (IEER)

13.2

12.9

12.5

10.9

11.9

Condensing Unit Only (IPLV)

15.9

17.3

15.9

15.9

16.0

13.63/12.31

16.36/14.13

16.37/14.22

25.40/22.32

24.6/22.17

Type

Scroll

Scroll

Manifolded Scrolls

Scroll

Manifolded Scroll

No./Tons

2/5.6

2/6.9

2/6.9

2/10.1

2/10.1

System kW/
Condensing Unit (kW)

Compressor

System Data
No. Refrigerant Circuits
Suction Line (in.) OD
Liquid Line (in.) OD

Outdoor Coil - Type


Tube Size (in.) OD

1 1/8

1 3/8

1 5/8

1 3/8

1 5/8

1/2

1/2

5/8

1/2

5/8

Lanced

Lanced

Lanced

Lanced

Lanced
0.375

0.375

0.375

0.375

0.375

Face Area (sq ft)

30.6

52.6

52.6

52.6

52.6

Rows/FPI

2/18

2/18

2/18

2/18

2/18

Outdoor Fan - Type

Propeller

Propeller

Propeller

Propeller

Propeller

No. Used/Diameter (in.)

1/28

2/28

2/28

2/28

2/28

Direct/1

Direct/1

Direct/1

Direct/1

Direct/1

9800

19500

19500

19500

19500

1/1

2/1

2/1

2/1

2/1

1100

1100

1100

1100

1100

30.7

39

37.6

43.8

41.3

Drive Type/No. Speeds


CFM
No. Motor/HP
Motor RPM

Refrigerant Charge
(Field Supplied)
(lbs of R410A)

Shipping Dimensions
(HxWxD)

22

49.48 x 53.25 x 41

49.48 x 94.75 x 47

49.48 x 94.75 x 47

SS-PRC028-EN

General Data

Table 4.

General Data 5-10 Ton Air Handler 60 Hz


5 Tons

7 Tons

10 Tons

Single
Circuit
Single
Single
TWE061D1, Dual Circuit,
Circuit
Dual Circuit,
Single
Circuit,
Dual Circuit,
D3, D4, DW, TWE061E1, TWE090D1, TWE090E1,
Circuit
TWE120D3, Dual Circuit, TWE120E3,
DK
E3, E4
D3, DW
E3
TWE120D1
DW, DK
TWE120E1
EW, EK
System Data
No. Refrigerant
Circuits

Suction Line
Connection (in.) OD

1 1/8

1 1/8

1 3/8

1 1/8

1 3/8

1 3/8

1 1/8

1 1/8

Liquid Line
Connection (in.) OD

1/2

1/2

1/2

1/2

1/2

1/2

1/2

1/2

Indoor Coil Type

Lanced

Lanced

Lanced

Lanced

Lanced

Lanced

Lanced

Lanced

Tube Size (in.)

0.375

0.375

0.375

0.375

0.375

0.375

0.375

0.375

5.0

5.0

8.1

8.1

11.2

11.2

11.2

11.2

4/14

4/14

4/14

4/14

4/14

4/14

4/14

4/14

Expansion
Valve

Expansion
Valve

Expansion
Valve

Expansion
Valve

Expansion
Valve

Expansion
Valve

Expansion
Valve

Expansion
Valve

1 PVC

1 PVC

1 PVC

1 PVC

1 PVC

1 PVC

1 PVC

1 PVC

Indoor Fan Type

Centrifugal

Centrifugal

Centrifugal

Centrifugal

Centrifugal

Centrifugal

Centrifugal

Centrifugal

No. Used/Diameter
x Width (in.)

1/12 x 12

1/12 x 12

1/15 x 15

1/15 x 15

1/15 x 15

1/15 x 15

1/15 x 15

1/15 x 15

Drive Type/
No. Speeds

Belt/
Adjustable

Belt/
Adjustable

Belt/
Adjustable

Belt/
Adjustable

Belt/
Adjustable

Belt/
Adjustable

Belt/
Adjustable

Belt/
Adjustable

2000

2000

3000

3000

4000

4000

4000

4000

0.75/1.0

0.75/1.0

1.5/2.0/3.0

1.5/2.0/3.0

2.0

2.0/3.0

2.0

2.0/3.0

Face Area (sq. ft.)


Rows/FPI
Refrigerant Control
Drain Connection
Size (in.)

CFM
No. Motors
Motor HP Standard/Oversized
Motor RPM

1725

1725

1725

1725

1725

1725

1725

1725

Motor Frame Size

56

56

56H

56H

56HZ

56HZ

56HZ

56HZ

Filters - Type/
Furnished

Throwaway/
Yes

Throwaway/
Yes

Throwaway/
Yes

Throwaway/
Yes

Throwaway/
Yes

Throwaway/
Yes

Throwaway/
Yes

Throwaway/
Yes

(No.)/Size
Recommended

(1) 16 x 20 x 1 (1) 16 x 20 x 1 (3) 16 X 25 X 1 (3) 16 X 25 X 1 (4) 16 X 25 X 1 (4) 16 X 25 X 1 (4) 16 X 25 X 1 (4) 16 X 25 X 1


(1) 20 x 20 x 1 (1) 20 x 20 x 1

Shipping
Dimensions
(HxWxD)

SS-PRC028-EN

23

General Data

Table 5.

General Data 12 - 20 Ton Air Handler 60 Hz


12 Tons

15 Tons

20 Tons

Dual Circuit,
TWE150E3, EW, EK

Dual Circuit,
TWE180E3, EW, EK

Dual Circuit,
TWE240E3, E4, EW, EK

System Data
No. Refrigerant Circuits
Suction Line Connection (in.) OD
Liquid Line Connection (in.) OD

Indoor Coil - Type


Tube Size (in.)

1 3/8

1 3/8

1 3/8

1/2

1/2

5/8

Lanced

Lanced

Lanced
0.375

0.375

0.375

Face Area (sq. ft.)

16.3

16.3

21.7

Rows/FPI

4/14

4/14

3/14

Expansion Valve

Expansion Valve

Expansion Valve

1 PVC

1 PVC

1 PVC

Centrifugal

Centrifugal

Centrifugal

Refrigerant Control
Drain Connection Size (in.)

Indoor Fan - Type


No. Used/Diameter x Width (in.)

2/15 x 15

2/15 x 15

2/15 x 15

Belt/Adjustable

Belt/Adjustable

Belt/Adjustable

5000

6000

8000

2.0/3.0/5.0

3.0/5.0

3.0/5.0/7.5

Motor RPM

1755

1728/1750

1750/3470

Motor Frame Size

145T

56HZ

184T

Filters - Type/Furnished

Throwaway/Yes

Throwaway/Yes

Throwaway/Yes

(No.)/Size Recommended

(8) 15 X 20 X 2

(8) 15 X 20 X 2

(4) 16 X 25 X 2
(4) 16 X 20 X 2

Drive Type/No. Speeds


CFM
No. Motors
Motor HP - Standard/Oversized

Shipping Dimensions
(HxWxD)

24

SS-PRC028-EN

Performance Data
Table 6.

Gross Cooling Capacities (MBH) 6 Tons TTA073D Condensing Unit with 7.5 Tons TWE090D Air Handler (IP)
Ambient Temperature (F)
85

95

105

Entering Wet Bulb (F)

Ent
61
67
73
61
67
73
61
67
73
DB
CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

2160

2400

2640

2880

75

72.1

59.9

78.9

46.4

86.3

31.8

68.3

58.1

75.1

44.9

82.2

30.3

64.6

56.3

71.1

43.2

77.8

28.8

80

72.7

70.7

79.2

56.9

86.7

42.9

69.4

69.1

75.4

55.2

82.5

41.3

66.0

66.0

71.3

53.6

78.1

39.7

85

75.9

75.9

79.5

67.5

86.9

53.6

72.9

72.9

75.7

65.9

82.8

52.1

69.7

69.7

71.8

64.1

78.4

50.4

90

79.8

79.8

80.5

78.3

87.1

64.3

76.7

76.7

76.9

76.7

83.0

62.7

73.3

73.3

73.3

73.3

78.6

61.1

75

73.4

63.0

80.1

48.5

87.4

32.3

69.5

61.2

76.3

46.9

83.1

30.8

65.8

59.4

72.1

45.3

78.7

29.3

80

74.3

74.3

80.4

59.8

87.9

44.4

71.2

71.2

76.5

58.1

83.6

42.9

68.0

68.0

72.4

56.5

79.1

41.3

85

78.3

78.3

80.9

71.3

88.2

56.2

75.1

75.1

77.1

69.7

83.9

54.7

71.7

71.7

73.0

68.0

79.4

53.0

90

82.3

82.3

82.3

82.3

88.4

68.0

79.0

79.0

79.0

79.0

84.1

66.1

75.5

75.5

75.5

75.5

79.6

64.4

75

74.6

66.0

81.2

50.6

88.2

32.8

70.6

64.2

77.2

49.0

83.9

31.3

66.8

62.4

73.0

47.3

79.4

29.8

80

76.2

76.2

81.3

62.3

88.9

46.0

73.0

73.0

77.4

60.7

84.5

44.4

69.6

69.6

73.2

59.0

80.0

42.8

85

80.4

80.4

82.1

75.0

89.2

58.8

77.0

77.0

78.2

73.4

84.9

57.2

73.5

73.5

74.2

71.7

80.3

55.6

90

84.5

84.5

84.4

84.4

89.5

71.1

81.0

81.0

81.0

81.0

85.1

69.5

77.4

77.4

77.3

77.3

80.6

67.8

75

75.6

68.9

82.0

52.6

89.0

33.3

71.5

67.1

78.0

51.0

84.6

31.8

67.7

65.3

73.7

49.3

80.0

30.3

80

77.9

77.9

82.3

64.9

89.7

47.4

74.6

74.6

78.2

63.3

85.3

45.9

71.1

71.1

74.0

61.5

80.7

44.2

85

82.1

82.1

83.3

78.7

90.1

61.3

78.7

78.7

79.4

77.1

85.7

59.7

75.1

75.1

75.0

75.0

80.9

57.7

90

86.4

86.4

86.4

86.4

90.5

74.4

82.8

82.8

82.7

82.7

86.1

72.8

79.0

79.0

79.0

79.0

81.5

71.1

Ambient Temperature (F)


115
Ent

125
Entering Wet Bulb (F)

DB

61

67

73

61

67

73

CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

2160

2400

2640

2880

75

60.7

54.5

66.8

41.5

73.1

27.1

56.5

52.6

62.1

39.6

68.0

25.4

80

62.6

62.6

67.0

51.8

73.5

38.0

58.9

58.9

62.4

49.9

68.3

36.2

85

66.2

66.2

67.6

62.4

73.7

48.7

62.3

62.3

63.0

60.4

68.5

46.9

90

69.7

69.7

69.7

69.7

73.9

59.2

65.7

65.7

65.7

65.7

68.8

57.3

75

61.8

57.6

67.7

43.5

73.9

27.6

57.5

55.6

62.9

41.7

68.7

25.9

80

64.4

64.4

67.9

54.5

74.4

39.6

60.5

60.5

63.2

52.5

69.1

37.7

85

68.1

68.1

68.8

66.2

74.6

51.3

64.0

64.0

64.0

64.0

69.3

49.5

90

71.7

71.7

71.7

71.7

74.9

62.7

67.5

67.5

67.5

67.5

69.7

60.7

75

62.8

60.6

68.5

45.6

74.6

28.1

58.3

58.3

63.6

43.7

69.3

26.4

80

65.9

65.9

68.8

57.1

75.1

41.1

61.9

61.9

63.9

55.2

69.7

39.2

85

69.7

69.7

69.7

69.7

75.4

53.9

65.5

65.5

65.5

65.5

69.9

51.7

90

73.5

73.5

73.4

73.4

75.8

66.0

69.1

69.1

69.0

69.0

70.5

64.1 Notes:

75

63.7

63.5

69.1

47.6

75.2

28.6

59.5

59.5

64.1

45.7

69.8

26.8

80

67.3

67.3

69.5

59.7

75.7

42.5

63.2

63.2

64.6

57.7

70.3

40.7

85

71.1

71.1

71.1

71.1

75.9

55.9

66.8

66.8

66.8

66.8

70.5

54.0

90

74.9

74.9

75.0

75.0

76.6

69.3

70.4

70.4

70.4

70.4

71.3

67.4

SS-PRC028-EN

1. All capacities shown are gross and have


not considered indoor fan heat. To obtain
net cooling, subtract indoor fan heat.
2. MBH = Total Gross Capacity
3. SHC = Sensible Heat Capacity

25

Performance Data

Table 7.

Gross Cooling Capacities (MBH) 7.5 Tons TTA090D Condensing Unit with 7.5 Tons TWE090D Air Handler (IP)
Ambient Temperature (F)
85

95

105

Entering Wet Bulb (F)

Ent
61
67
73
61
67
73
61
67
73
DB
CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

2700

3000

75

89.1

74.8

96.9

58.0

105.8

38.9

84.6

72.6

92.5

56.2

101.0

37.2

80.3

70.6

87.8

54.3

95.8

35.5

80

89.8

88.5

97.1

70.7

105.9

52.8

85.9

85.9

92.7

68.8

101.1

51.0

82.2

82.2

88.0

66.9

96.0

49.2

85

93.9

93.9

97.5

84.2

106.0

66.3

90.3

90.3

93.2

82.3

101.2

64.6

86.5

86.5

88.6

80.3

96.1

62.7

90

98.4

98.4

98.9

97.9

106.1

79.8

94.7

94.7

94.7

94.7

101.4

78.1

90.7

90.7

90.7

90.7

96.3

76.2

75

90.6

78.7

98.3

60.6

107.1

39.6

85.9

76.4

93.8

58.8

102.1

37.9

81.6

74.4

88.9

56.9

96.9

36.1

80

91.8

91.8

98.5

74.2

107.2

54.7

88.2

88.2

94.8

72.7

102.3

52.9

84.4

84.4

89.1

70.4

97.1

51.0

85

96.5

96.5

99.1

88.9

107.3

69.5

92.8

92.8

95.5

87.4

102.4

67.7

88.8

88.8

90.0

85.0

97.2

65.9

101.2 101.2 101.1 101.1 107.5

84.3

97.3

97.3

97.3

97.3

102.7

82.5

93.2

93.2

93.1

93.1

97.5

80.4

90

3300

75

91.9

82.3

80

94.0

85

98.8

90
75
3600

80

99.4

63.3

108.1

40.2

87.2

80.1

94.8

61.4

103.1

38.5

82.8

78.1

89.9

59.5

97.8

36.7

94.0

99.6

77.6

108.3

56.5

90.2

90.2

94.9

75.5

103.3

54.7

86.2

86.2

90.1

73.5

98.0

52.9

98.8

100.5

93.5

108.5

72.6

94.9

94.9

96.0

91.6

103.5

70.8

90.7

90.7

91.3

89.6

98.1

68.9

103.6 103.6 103.5 103.5 108.7

88.4

99.5

99.5

99.5

99.5

103.8

86.5

95.2

95.2

95.2

95.2

98.6

84.6

93.1

85.9

100.4

65.8

109.0

40.9

88.3

83.7

95.7

64.0

103.9

39.2

83.8

81.6

90.7

62.1

98.5

37.4

95.9

95.9

100.6

80.6

109.2

58.3

92.0

92.0

95.9

78.7

104.2

56.5

87.8

87.8

91.0

76.7

98.8

54.6

85

100.8 100.8 101.8

97.9

109.4

75.6

96.8

96.8

97.3

96.1

104.3

73.8

92.5

92.5

92.4

92.4

98.9

71.9

90

105.7 105.7 105.6 105.6 109.8

92.5

101.5 101.5 101.5 101.5 104.8

90.6

97.1

97.1

97.1

97.1

99.5

88.6

Ambient Temperature (F)


115
Ent
DB

125
Entering Wet Bulb (F)

61

67

73

61

67

73

CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

2700

3000

3300

3600

26

75

75.7

68.5

82.7

52.3

90.2

33.5

70.6

66.1

77.0

50.0

83.9

31.4

80

78.1

78.1

82.9

64.8

90.4

47.2

73.5

73.5

77.2

62.5

84.1

45.0

85

82.2

82.2

83.6

78.2

90.5

60.7

77.5

77.5

78.1

75.8

84.3

58.5

90

86.4

86.4

86.3

86.3

90.8

74.2

81.4

81.4

81.3

81.3

84.6

71.7

75

76.9

72.2

83.7

54.9

91.2

34.2

71.8

69.8

77.9

52.6

84.7

32.0

80

80.1

80.1

83.9

68.1

91.4

49.0

75.3

75.3

78.1

65.7

85.0

46.8

85

84.4

84.4

85.0

82.9

91.5

63.8

79.4

79.4

79.3

79.3

85.1

61.6

90

88.6

88.6

88.5

88.5

91.9

78.3

83.4

83.4

83.4

83.4

85.6

75.9

75

78.1

75.9

84.5

57.5

92.0

34.8

72.7

72.7

78.6

55.2

85.4

32.6

80

81.8

81.8

84.8

71.3

92.2

50.9

76.9

76.9

79.0

68.9

85.7

48.6

85

86.2

86.2

86.1

86.1

92.3

66.9

81.0

81.0

81.0

81.0

85.8

64.7

90

90.5

90.5

90.5

90.5

92.9

82.5

85.1

85.1

85.1

85.1

86.5

80.1 Notes:

75

78.9

78.9

85.2

60.1

92.6

35.4

74.0

74.0

79.2

57.8

86.0

33.2

80

83.3

83.3

85.7

74.5

92.9

52.6

78.2

78.2

79.7

72.1

86.3

50.4

85

87.8

87.8

87.7

87.7

93.0

69.9

82.4

82.4

82.4

82.4

86.4

67.3

90

92.2

92.2

92.2

92.2

93.8

86.5

86.6

86.6

86.6

86.6

87.4

84.1

1. All capacities shown are gross and have


not considered indoor fan heat. To obtain
net cooling, subtract indoor fan heat.
2. MBH = Total Gross Capacity
3. SHC = Sensible Heat Capacity

SS-PRC028-EN

Performance Data

Table 8.

Gross Cooling Capacities (MBH) 7.5 Tons TTA090D Condensing Unit with 10 Tons TWE120D Air Handler (IP)
Ambient Temperature (F)
85

95

105

Entering Wet Bulb (F)

Ent
61
67
73
61
67
73
61
67
73
DB
CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

3100

75

95.4

84.3

102.9

63.6

111.3

41.4

90.4

81.9

98.2

61.7

106.2

39.6

85.8

79.8

93.2

59.8

100.7

37.8

80

97.1

97.1

103.1

79.2

111.9

58.1

93.3

93.3

98.4

77.2

106.8

56.3

89.1

89.1

93.5

75.1

101.4

54.4

85

102.0 102.0 104.0

95.4

112.1

74.5

98.0

98.0

99.4

93.4

107.1

72.7

93.8

93.8

94.6

91.3

101.7

70.8

90

106.9 106.9 106.8 106.8 112.4

90.1

102.8 102.8 102.7 102.7 107.5

88.2

98.4

98.4

98.3

98.3

102.2

86.2

75
3400

80

104.0

66.3

112.3

42.0

99.3

99.3

104.3

82.8

91.6

85.9

99.2

64.4

107.1

40.3

87.0

83.8

94.1

62.4

102.9

38.8

95.3

95.3

56.5

112.9

60.2

100.6

81.3

107.8

58.4

91.0

91.0

94.5

78.7

102.3

104.4 104.4 105.5 100.5 113.2

78.0

100.2 100.2 100.8

98.5

108.0

75.6

95.8

95.8

95.8

95.8

102.5

73.6

90

109.3 109.3 109.2 109.2 113.6

94.7

105.1 105.1 105.0 105.0 108.6

92.8

100.5 100.5 100.5 100.5 103.2

90.8

104.9

68.9

113.1

42.7

92.8

89.9

100.0

67.0

109.1

41.3

88.1

87.7

94.8

65.0

102.2

39.0

80

101.2 101.2 105.3

86.3

113.8

62.2

97.1

97.1

100.5

84.3

108.6

60.4

92.7

92.7

95.4

82.2

103.1

58.5

85

106.4 106.4 106.8 105.5 114.0

80.6

102.1 102.1 102.1 102.1 108.8

78.7

97.6

97.6

97.6

97.6

103.3

76.6

90

111.4 111.4 111.3 111.3 114.7

99.2

107.1 107.1 107.1 107.1 109.7

97.4

102.4 102.4 102.4 102.4 104.2

95.3

75
4000

88.3

85
75

3700

96.7

97.9

99.1

92.3

105.7

71.5

115.1

43.7

93.9

93.7

100.8

69.6

108.5

41.5

89.3

89.3

95.4

66.6

102.8

39.7

80

102.9 102.9 106.3

96.2

89.8

114.6

64.2

98.7

98.7

101.4

87.7

109.3

62.4

94.2

94.2

96.2

85.6

103.7

60.5

85

108.2 108.2 108.1 108.1 114.8

83.7

103.8 103.8 103.8 103.8 109.6

81.8

99.1

99.1

99.1

99.1

104.0

79.7

90

113.2 113.2 113.2 113.2 115.6 103.7 108.8 108.8 108.8 108.8 110.6 101.8 104.0 104.0 104.0 104.0 105.1

99.7

Ambient Temperature (F)


115
Ent

125
Entering Wet Bulb (F)

DB

61

67

73

61

67

73

CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

3100

3400

3700

4000

75

81.0

77.4

87.7

57.6

94.8

35.8

75.6

74.9

81.6

55.3

88.1

33.5

80

84.6

84.6

88.1

72.8

95.5

52.4

79.5

79.5

82.1

70.3

88.9

50.1

85

89.1

89.1

89.4

89.1

95.7

68.2

83.8

83.8

83.8

83.8

89.1

65.7

90

93.6

93.6

93.5

93.5

96.3

84.0

88.0

88.0

88.0

88.0

89.8

81.5

75

82.1

81.4

88.5

60.3

95.5

36.4

76.8

76.8

82.3

57.9

88.8

34.2

80

86.4

86.4

89.0

76.4

96.3

54.4

81.2

81.2

82.9

73.8

89.6

52.2

85

91.0

91.0

91.0

91.0

96.5

71.3

85.5

85.5

85.5

85.5

89.9

68.8

90

95.5

95.5

95.5

95.5

97.4

88.5

89.8

89.8

89.8

89.8

90.8

86.0

75

83.3

83.3

89.2

62.9

96.2

37.0

78.1

78.1

82.8

59.4

89.1

37.2

80

88.0

88.0

89.9

79.9

97.0

56.4

82.5

82.5

83.7

77.3

90.2

54.2

85

92.6

92.6

92.6

92.6

97.3

74.4

86.9

86.9

86.9

86.9

90.5

71.8

90

97.2

97.2

97.2

97.2

98.3

93.0

91.3

91.3

91.3

91.3

91.7

90.5 Notes:

75

84.5

84.5

89.7

64.3

96.7

37.6

79.2

79.2

83.3

61.6

89.6

35.4

80

89.3

89.3

90.6

83.3

99.0

58.9

83.7

83.7

84.4

80.7

90.6

56.3

85

94.0

94.0

94.0

94.0

98.0

77.4

88.2

88.2

88.2

88.2

91.1

74.8

90

98.7

98.7

98.7

98.7

99.2

97.4

92.7

92.7

92.7

92.7

92.6

92.6

SS-PRC028-EN

1. All capacities shown are gross and have


not considered indoor fan heat. To obtain
net cooling, subtract indoor fan heat.
2. MBH = Total Gross Capacity
3. SHC = Sensible Heat Capacity

27

Performance Data

Table 9.

Gross Cooling Capacities (MBH) 10 Tons TTA120D Condensing Unit with 10 Tons TWE120D Air Handler (IP)
Ambient Temperature (F)
85

95

105

Entering Wet Bulb (F)

Ent
61
67
73
61
67
73
61
67
73
DB
CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

3600

4000

4400

4800

75

116.8 100.6 128.1

77.2

139.8

51.6

111.3

122.0

74.7

133.2

49.3

105.5

115.6

72.2

126.2

46.8

80

118.8 118.8 128.4

95.4

140.2

70.8

114.1 114.1 122.3

92.9

133.6

68.4

109.0 109.0 115.9

90.2

126.6

65.9

85

125.2 125.2 129.2 114.2 140.5

89.6

120.2 120.2 123.2 111.6 133.8

87.2

115.0 115.0 117.0 109.0 126.8

84.6

90

131.5 131.5 131.4 131.4 140.9 108.4 126.4 126.4 126.3 126.3 134.2 106.0 120.9 120.9 120.8 120.8 127.2 103.2

75

118.8 106.0 129.9

141.4

52.5

113.2 103.5 123.6

78.3

134.7

50.1

107.3 100.8 117.1

75.7

127.6

47.7

80

122.2 122.2 130.2 100.5 141.9

73.5

117.3 117.3 124.0

97.9

135.1

71.1

111.9 111.9 117.4

95.1

128.0

68.5

85

128.8 128.8 131.4 120.9 142.3

94.2

123.6 123.6 125.3 118.4 135.4

91.7

118.1 118.1 119.0 115.8 128.2

89.1

90

135.3 135.3 135.2 135.2 142.7 114.4 129.9 129.9 129.8 129.8 135.9 111.9 124.1 124.1 124.0 124.0 128.9 109.3

75

120.6 111.3 131.3

142.8

53.3

114.9 108.8 125.0

135.9

51.0

109.0 106.1 118.3

79.2

128.7

48.5

80

125.1 125.1 131.7 105.0 143.4

76.1

119.9 119.9 125.4 102.4 136.4

73.7

114.5 114.5 118.8

99.8

129.2

71.1

85

131.9 131.9 133.4 127.5 143.7

98.6

126.5 126.5 127.3 125.0 136.7

96.1

120.8 120.8 120.7 120.7 129.4

93.6

90

138.5 138.5 138.5 138.5 144.4 120.4 132.9 132.9 132.8 132.8 137.5 117.9 126.9 126.9 126.9 126.9 130.3 115.3

75

122.2 116.5 132.6

143.9

54.2

116.5 114.0 126.1

136.9

51.8

110.2 110.2 119.3

129.6

49.4

80

127.7 127.7 133.1 109.6 144.6

78.7

122.3 122.3 126.7 107.0 137.5

76.2

116.7 116.7 120.0 104.4 130.1

73.7

85

134.6 134.6 135.2 134.0 144.9 103.0 129.0 129.0 128.9 128.9 137.8 100.5 123.1 123.1 123.0 123.0 130.4

97.5

90

141.4 141.4 141.3 141.3 145.8 126.2 135.5 135.5 135.5 135.5 138.9 123.8 129.4 129.4 129.3 129.3 131.6 121.2

80.7

84.3

87.8

98.0

81.8

85.3

95.4

82.7

Ambient Temperature (F)


115
Ent
DB

125
Entering Wet Bulb (F)

61

67

73

61

67

73

CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC
75
3600

4000

4400

4800

28

108.8

69.4

118.8

44.2

92.6

89.5

101.2

66.5

110.7

80

103.5 103.5 109.1

99.3

92.5

87.5

119.1

63.2

97.4

97.4

101.7

84.5

111.0

60.4

85

109.3 109.3 110.3 106.3 119.3

81.9

103.0 103.0 102.9 102.9 111.1

79.0

90

115.0 115.0 114.9 114.9 119.8 100.4 108.4 108.4 108.3 108.3 111.8

97.5

75

101.1

110.1

73.0

120.0

45.1

94.1

94.1

102.4

70.0

111.7

42.3

80

106.2 106.2 110.5

92.3

120.4

65.9

99.9

99.9

102.9

89.2

112.0

63.0

85

112.1 112.1 112.1 112.1 120.6

86.4

105.5 105.5 105.5 105.5 112.3

83.6

90

117.9 117.9 117.9 117.9 121.4 106.6 111.1 111.1 111.1 111.1 113.2 103.7

75

102.4 102.4 111.1

76.5

121.0

45.9

103.3

73.5

112.6

43.2

80

108.5 108.5 111.8

97.0

121.4

68.5

102.0 102.0 104.1

94.0

112.9

65.6

85

114.6 114.6 114.5 114.5 121.7

90.9

107.7 107.7 107.7 107.7 113.2

87.7

90

120.5 120.5 120.5 120.5 122.7 112.6 113.4 113.4 113.4 113.4 114.5 109.7 Notes:

75

104.3 104.3 112.0

121.8

46.8

80

110.6 110.6 112.9 101.6 122.3

85

116.7 116.7 116.6 116.6 122.6

90

122.7 122.7 122.7 122.7 124.0 118.5 115.4 115.4 115.3 115.3 115.7 115.6

98.0

79.9

96.1

97.8

96.1

97.8

41.5

104.1

76.9

113.3

44.0

71.0

103.8 103.8 105.1

98.6

113.7

68.1

94.7

109.6 109.6 109.5 109.5 114.1

91.7

1. All capacities shown are gross and have


not considered indoor fan heat. To obtain
net cooling, subtract indoor fan heat.
2. MBH = Total Gross Capacity
3. SHC = Sensible Heat Capacity

SS-PRC028-EN

Performance Data

Table 10. Gross Cooling Capacities (MBH) 10 Tons TTA120E Condensing Unit with 10 Tons TWE120E Air Handler (IP)
Ambient Temperature (F)
85

95

105

Entering Wet Bulb (F)

Ent
61
67
73
61
67
73
61
67
73
DB
CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

3600

4000

4400

4800

75

116.0

127.4

77.3

139.2

51.3

110.2

121.0

74.8

132.2

48.9

104.1

114.2

72.1

124.9

46.3

80

118.2 116.8 127.6

99.6

94.3

139.4

70.1

112.8 112.8 121.2

91.6

132.3

67.5

107.4 107.4 114.4

88.9

125.0

64.9

85

124.0 124.0 128.2 113.0 139.5

88.6

118.8 118.8 121.8 110.3 132.4

85.9

113.3 113.3 115.2 107.5 125.1

83.3

90

130.2 130.2 130.6 129.2 139.8 107.1 124.8 124.8 124.7 124.7 132.7 104.5 119.0 119.0 119.0 119.0 125.4 101.7

75

118.0 104.9 129.1

81.0

140.9

52.2

112.0 102.2 122.5

78.4

133.7

49.8

105.8

115.6

75.7

126.2

47.2

80

121.1 121.1 129.4

99.2

141.1

72.7

115.9 115.9 122.8

96.4

133.8

70.1

110.3 110.3 115.9

93.6

126.3

67.4

85

127.5 127.5 130.3 119.6 141.2

92.9

122.0 122.0 123.8 117.0 134.0

90.3

116.3 116.3 116.2 116.2 126.5

87.6

90

133.9 133.9 133.8 133.8 141.5 113.1 128.2 128.2 128.1 128.1 134.3 110.5 122.1 122.1 122.1 122.1 126.9 107.7

75

119.7 110.1 130.6

142.3

53.1

113.7 107.4 123.8

134.9

50.6

106.5 106.5 116.8

79.2

127.3

48.1

80

124.0 124.0 130.9 103.8 142.5

75.2

118.5 118.5 124.2 101.1 135.1

72.6

112.7 112.7 117.1

98.2

127.5

69.9

85

130.6 130.6 132.2 126.1 142.6

97.1

124.9 124.9 124.8 124.8 135.3

94.5

118.9 118.9 119.2 117.6 127.6

91.8

90

137.0 137.0 137.0 137.0 143.0 118.9 131.1 131.1 131.1 131.1 135.8 116.3 124.9 124.9 124.8 124.8 128.3 113.6

75

121.2 115.2 131.8

143.4

54.0

114.3 114.3 125.0

136.0

51.5

108.6 108.6 117.8

128.2

48.9

80

126.5 126.5 132.2 108.3 143.6

77.6

120.8 120.8 125.4 105.5 136.2

75.0

114.9 114.9 118.3 102.7 128.4

72.3

85

133.2 133.2 133.1 133.1 143.8 101.2 127.3 127.3 127.7 125.9 136.4

98.7

121.1 121.1 121.0 121.0 128.6

95.9

90

139.8 139.8 139.7 139.7 144.2 124.6 133.6 133.6 133.6 133.6 137.1 122.1 127.2 127.2 127.2 127.2 129.5 119.3

84.6

88.1

96.9

81.9

85.5

94.0

99.3

82.8

Ambient Temperature (F)


115
Ent

125
Entering Wet Bulb (F)

DB

61

67

73

61

67

73

CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC
75
3600

107.0

69.2

117.1

43.7

90.6

87.9

99.2

66.2

108.7

80

101.7 101.7 107.2

86.0

117.2

62.1

95.3

95.3

99.5

82.8

108.8

59.1

85

107.3 107.3 108.3 104.7 117.3

80.5

100.8 100.8 101.1

99.7

108.9

77.5

90

112.9 112.9 112.8 112.8 117.6

98.9

106.1 106.1 106.0 106.0 109.4

95.8

75
4000

4400

4800

97.6

99.3

91.0

108.2

72.8

118.3

44.5

92.1

92.1

100.3

69.8

109.7

80

104.3 104.3 108.6

90.7

118.4

64.6

97.7

97.7

100.7

87.5

109.8

61.7

85

110.1 110.1 110.4 108.8 118.5

84.8

103.3 103.3 103.2 103.2 110.0

81.9

90

115.7 115.7 115.7 115.7 119.1 104.9 108.7 108.7 108.6 108.6 110.7 101.9

75

100.6 100.6 109.3

76.4

119.3

45.4

94.0

94.0

101.2

73.3

110.6

80

106.5 106.5 109.7

95.3

119.4

67.1

99.7

99.7

101.8

92.1

110.7

64.1

85

112.4 112.4 112.3 112.3 119.5

89.0

105.4 105.4 105.3 105.3 110.9

85.9

90

118.2 118.2 118.1 118.1 120.4 110.8 110.9 110.9 110.9 110.9 112.0 107.8 Notes:

75

102.4 102.4 110.1

79.9

120.1

46.3

80

108.5 108.5 110.8

99.8

120.2

85

114.4 114.4 114.4 114.4 120.4

90

120.3 120.3 120.3 120.3 121.6 116.5 112.8 112.8 112.8 112.8 112.7 112.7

SS-PRC028-EN

96.4

40.8

95.6

95.6

41.7

42.6

101.9

76.9

111.3

43.4

69.5

101.5 101.5 102.8

96.6

111.4

66.5

93.0

107.2 107.2 107.1 107.1 111.7

90.0

1. All capacities shown are gross and have


not considered indoor fan heat. To obtain
net cooling, subtract indoor fan heat.
2. MBH = Total Gross Capacity
3. SHC = Sensible Heat Capacity

29

Performance Data

Table 11. Gross Cooling Capacities (MBH) One Compressor - 10 Tons TTA120F Condensing Unit with 10 Tons TWE120D
Air Handler (IP)
Ambient Temperature (F)
85

95

105

Entering Wet Bulb (F)

Ent
61
67
73
61
67
73
61
67
73
DB
CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

3600

4000

4400

4800

75

69.9

69.9

74.1

56.2

81.1

31.8

66.3

66.3

69.7

54.7

76.6

30.3

62.5

62.5

65.3

53.1

71.7

28.8

80

74.4

74.4

75.1

72.2

81.5

49.7

70.7

70.7

70.9

70.7

76.8

48.1

66.7

66.7

66.7

66.7

71.9

46.4

85

78.9

78.9

78.9

78.9

81.9

67.2

75.0

75.0

75.0

75.0

77.2

65.7

70.9

70.9

70.9

70.9

72.4

64.1

90

83.4

83.4

83.3

83.3

83.3

83.3

79.3

79.3

79.2

79.2

79.2

79.2

75.0

75.0

75.0

75.0

74.9

74.9

75

71.3

71.3

74.7

59.5

81.7

32.7

67.6

67.6

70.3

58.0

77.1

31.2

63.7

63.7

65.8

56.5

72.2

29.6

80

75.9

75.9

75.9

75.9

82.1

51.8

72.1

72.1

72.0

72.0

77.4

50.5

68.0

68.0

68.0

68.0

72.4

48.8

85

80.5

80.5

80.5

80.5

82.6

71.1

76.4

76.4

76.4

76.4

77.9

69.6

72.2

72.2

72.2

72.2

73.1

68.1

90

85.0

85.0

85.0

85.0

85.0

85.0

80.8

80.8

80.7

80.7

80.7

80.7

76.3

76.3

76.3

76.3

76.2

76.2

75

72.5

72.5

75.3

62.7

82.2

33.5

68.6

68.6

70.9

61.3

77.6

32.0

64.6

64.6

66.3

59.9

72.6

30.5

80

77.2

77.2

77.2

77.2

82.6

53.9

73.2

73.2

73.2

73.2

77.8

52.5

69.0

69.0

69.0

69.0

72.8

50.9

85

81.8

81.8

81.8

81.8

83.3

74.9

77.7

77.7

77.6

77.6

78.5

73.5

73.3

73.3

73.3

73.3

73.7

72.0

90

86.4

86.4

86.4

86.4

86.3

86.3

82.0

82.0

82.0

82.0

82.0

82.0

77.4

77.4

77.4

77.4

77.4

77.4

75

73.5

73.5

75.8

66.0

82.6

33.7

69.6

69.6

71.3

64.6

77.9

32.9

65.5

65.5

66.7

63.2

72.9

31.3

80

78.3

78.3

78.2

78.2

83.0

56.0

74.2

74.2

74.2

74.2

78.2

54.5

69.9

69.9

69.9

69.9

73.1

53.0

85

83.0

83.0

82.9

82.9

83.9

78.6

78.7

78.7

78.7

78.7

79.1

77.2

74.2

74.2

74.2

74.2

74.2

74.2

90

87.6

87.6

87.6

87.6

87.5

87.5

83.1

83.1

83.1

83.1

83.1

83.1

78.4

78.4

78.4

78.4

78.4

78.4

Ambient Temperature (F)


115
Ent
DB

125
Entering Wet Bulb (F)

61

67

73

61

67

73

CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

3600

4000

4400

4800

30

75

58.5

58.5

60.6

51.5

66.7

27.2

54.2

54.2

55.6

49.7

61.3

25.5

80

62.5

62.5

62.5

62.5

66.8

44.7

58.0

58.0

58.0

58.0

61.4

42.9

85

66.5

66.5

66.5

66.5

67.4

62.5

61.9

61.9

61.9

61.9

62.2

60.8

90

70.4

70.4

70.4

70.4

70.3

70.3

65.6

65.6

65.6

65.6

65.5

65.5

75

59.5

59.5

61.1

54.9

67.1

28.0

55.1

55.1

56.1

53.2

61.6

26.3

80

63.7

63.7

63.6

63.6

67.2

47.1

59.0

59.0

59.0

59.0

61.8

45.2

85

67.7

67.7

67.7

67.7

68.1

66.5

62.9

62.9

62.9

62.9

62.9

62.9

90

71.6

71.6

71.6

71.6

71.5

71.5

66.6

66.6

66.6

66.6

66.6

66.6

75

60.4

60.4

61.5

58.3

67.4

28.8

55.9

55.9

56.5

56.5

62.0

27.2

80

64.6

64.6

64.6

64.6

67.6

49.2

59.9

59.9

59.9

59.9

62.2

47.5

85

68.7

68.7

68.7

68.7

68.6

68.6

63.8

63.8

63.8

63.8

63.8

63.8

90

72.6

72.6

72.6

72.6

72.6

72.6

67.5

67.5

67.5

67.5

67.5

67.5 Notes:

75

61.2

61.2

61.9

61.7

67.7

29.7

56.5

56.5

56.9

55.2

62.2

28.0

80

65.4

65.4

65.4

65.4

67.9

51.4

60.6

60.6

60.6

60.6

62.4

49.6

85

69.5

69.5

69.5

69.5

69.5

69.5

64.6

64.6

64.6

64.6

64.5

64.5

90

73.5

73.5

73.5

73.5

73.5

73.5

68.2

68.2

68.2

68.2

68.2

68.2

1. All capacities shown are gross and have


not considered indoor fan heat. To obtain
net cooling, subtract indoor fan heat.
2. MBH = Total Gross Capacity
3. SHC = Sensible Heat Capacity

SS-PRC028-EN

Performance Data

Table 12. Gross Cooling Capacities (MBH) Both Compressors - 10 Tons TTA120F Condensing Unit with 10 Tons TWE120D
Air Handler (IP)
Ambient Temperature (F)
85

95

105

Entering Wet Bulb (F)

Ent
61
67
73
61
67
73
61
67
73
DB
CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

3600

4000

4400

4800

75

116.2

128.2

77.3

140.8

51.8

110.5

121.9

74.8

133.8

49.4

104.6

115.3

72.1

126.6

46.9

80

118.2 117.9 128.4

99.0

94.1

140.9

70.4

112.9 112.9 122.1

91.4

134.0

67.9

107.8 107.8 115.5

88.7

126.7

65.2

85

124.2 124.2 128.9 112.4 141.1

88.7

119.2 119.2 122.8 109.7 134.1

86.1

113.8 113.8 116.3 106.9 126.9

83.4

90

130.7 130.7 130.6 130.6 141.3 106.9 125.4 125.4 125.4 125.4 134.3 104.2 119.9 119.9 119.8 119.8 127.1 101.6

75

118.2 104.1 130.1

81.0

142.6

52.8

112.5 101.4 123.6

78.4

135.5

50.3

106.4

116.8

75.7

128.0

47.8

80

121.2 121.2 130.3

98.8

142.7

73.0

116.1 116.1 123.8

96.2

135.6

70.4

110.7 110.7 117.0

93.4

128.2

67.7

85

127.9 127.9 131.2 118.8 142.9

92.9

122.6 122.6 124.9 116.1 135.8

90.3

117.0 117.0 118.3 113.3 128.4

87.6

90

134.5 134.5 134.5 134.5 143.2 112.8 129.0 129.0 129.0 129.0 136.1 110.2 123.2 123.2 123.1 123.1 128.7 107.3

75

120.0 109.1 131.6

144.1

53.7

114.1 106.4 125.0

136.8

51.2

108.0 103.5 118.1

79.3

129.2

48.6

80

124.2 124.2 131.9 103.4 144.3

75.4

118.9 118.9 125.2 100.6 137.0

72.8

113.3 113.3 118.4

97.7

129.4

70.1

85

131.1 131.1 133.2 125.0 144.5

97.1

125.6 125.6 126.8 122.3 137.2

94.4

119.7 119.7 120.2 119.5 129.6

91.7

90

137.9 137.9 137.8 137.8 144.8 118.4 132.1 132.1 132.0 132.0 137.7 115.7 126.0 126.0 126.0 126.0 130.2 112.9

75

121.6 113.9 133.0

145.4

54.5

115.7 111.2 126.2

138.0

52.1

109.5 108.4 119.1

130.2

49.5

80

126.8 126.8 133.2 107.6 145.6

77.8

121.4 121.4 126.6 104.9 138.2

75.2

115.5 115.5 119.6 102.0 130.5

72.5

85

133.9 133.9 135.0 131.1 145.8 101.1 128.1 128.1 128.6 128.4 138.4

98.4

122.1 122.1 122.0 122.0 130.7

95.7

90

140.8 140.8 140.7 140.7 146.3 123.9 134.8 134.8 134.7 134.7 139.1 121.2 128.5 128.5 128.5 128.5 131.5 118.4

84.5

88.1

96.3

82.0

85.5

93.4

98.6

82.8

Ambient Temperature (F)


115
Ent

125
Entering Wet Bulb (F)

DB

61

67

73

61

67

73

CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC
75
3600

4000

4400

4800

108.2

69.4

118.8

44.2

91.5

87.4

100.6

66.4

110.5

80

102.2 102.2 108.4

98.3

90.5

85.8

119.0

62.4

96.1

96.1

100.9

82.7

110.6

41.4
59.5

85

108.1 108.1 109.5 104.0 119.2

80.6

101.7 101.7 102.2 101.0 110.8

77.6

107.3 107.3 107.2 107.2 111.2

95.5

90

113.9 113.9 113.8 113.8 119.5

98.8

75

100.0

109.6

72.9

120.1

45.1

93.2

92.5

101.8

69.9

111.6

80

104.9 104.9 109.8

90.3

120.3

64.9

98.6

98.6

102.1

87.2

111.8

62.0

85

111.0 111.0 111.5 110.4 120.5

84.8

104.3 104.3 104.3 104.3 111.9

81.8

90

116.9 116.9 116.8 116.8 121.0 104.4 110.0 110.0 110.0 110.0 112.7 101.3

75

101.6 100.6 110.7

76.5

121.2

46.0

102.7

73.5

112.5

43.1

80

107.3 107.3 111.1

94.8

121.4

67.3

100.7 100.7 103.3

91.6

112.7

64.4

85

113.4 113.4 113.4 113.4 121.6

88.9

106.6 106.6 106.5 106.5 112.9

85.9

90

119.5 119.5 119.5 119.5 122.4 110.0 112.3 112.3 112.3 112.3 113.9 106.9 Notes:

95.6

94.8

75

103.0 103.0 111.7

80.0

122.1

46.8

103.6

77.0

113.3

44.0

80

109.3 109.3 112.2

99.0

122.3

69.7

102.6 102.6 104.3

95.9

113.5

66.7

85

115.6 115.6 115.5 115.5 122.5

92.9

108.5 108.5 108.4 108.4 113.7

89.6

90

121.8 121.8 121.7 121.7 123.6 115.5 114.3 114.3 114.3 114.3 115.1 112.4

SS-PRC028-EN

96.5

94.8

96.5

42.3

1. All capacities shown are gross and have


not considered indoor fan heat. To obtain
net cooling, subtract indoor fan heat.
2. MBH = Total Gross Capacity
3. SHC = Sensible Heat Capacity

31

Performance Data

Table 13. Gross Cooling Capacities (MBH) 12.5 Tons TTA150E Condensing Unit with 12.5 Tons TWE150E Air Handler (IP)
Ambient Temperature (F)
85

95

105

Entering Wet Bulb (F)

Ent
61
67
73
61
67
73
61
67
73
DB
CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

4500

5000

5500

6000

75

146.0 123.7 159.9

174.1

64.1

138.7 120.2 151.8

165.4

61.0

130.9 116.5 143.4

156.3

57.9

80

148.1 147.1 160.2 117.0 174.3

96.1

87.1

141.2 141.2 152.1 113.6 165.6

92.9

83.9

134.5 134.5 143.6 110.1 156.5

89.5

80.6

85

155.0 155.0 160.8 139.9 174.5 109.7 148.5 148.5 152.8 136.3 165.8 106.5 141.6 141.6 144.6 132.8 156.7 103.2

90

162.5 162.5 162.4 162.4 174.7 132.3 155.7 155.7 155.7 155.7 166.0 129.0 148.6 148.6 148.5 148.5 157.0 125.7

75

148.3 130.0 162.0 100.5 176.1

65.2

140.9 126.5 153.8

167.2

62.1

133.0 122.9 145.1

158.0

59.0

80

151.6 151.6 162.3 122.8 176.3

90.2

145.0 145.0 154.0 119.4 167.4

87.0

138.0 138.0 145.4 115.9 158.2

83.7

85

159.4 159.4 163.3 147.7 176.6 115.0 152.5 152.5 155.2 144.2 167.6 111.7 145.3 145.3 146.9 140.7 158.4 108.4

97.2

93.9

90

167.0 167.0 166.9 166.9 176.8 139.6 159.9 159.9 159.9 159.9 168.0 136.4 152.5 152.5 152.4 152.4 158.9 133.1

75

150.5 136.2 163.8 104.9 177.8

66.2

142.9 132.7 155.4 101.6 168.7

63.2

134.9 129.1 146.6

159.4

60.0

80

155.1 155.1 164.1 128.5 178.0

93.2

148.3 148.3 155.7 125.1 169.0

90.0

141.0 141.0 147.0 121.6 159.6

86.7

85

163.1 163.1 165.5 155.3 178.3 120.0 156.0 156.0 157.4 151.9 169.2 116.8 148.5 148.5 148.4 148.4 159.8 113.4

98.2

90

170.8 170.8 170.8 170.8 178.7 146.8 163.5 163.5 163.4 163.4 169.7 143.2 155.8 155.8 155.8 155.8 160.5 139.8

75

152.4 142.2 165.4 109.2 179.2

67.3

144.7 138.7 156.8 105.9 170.0

64.2

136.7 135.1 147.8 102.5 160.5

61.0

80

158.2 158.2 165.7 134.0 179.5

96.1

151.1 151.1 157.2 130.3 170.3

92.9

143.7 143.7 148.4 126.7 160.8

89.6

85

166.3 166.3 167.6 162.7 179.7 125.0 159.0 159.0 158.9 158.9 170.5 121.7 151.3 151.3 151.2 151.2 161.0 118.4

90

174.2 174.2 174.1 174.1 180.3 153.3 166.6 166.6 166.6 166.6 171.2 150.0 158.7 158.7 158.7 158.7 162.0 146.6

Ambient Temperature (F)


115
Ent
DB

125
Entering Wet Bulb (F)

61

67

73

61

67

73

CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

4500

5000

5500

6000

75

122.8 112.7 134.4

146.7

54.6

114.0 108.7 124.7

136.2

51.0

80

127.2 127.2 134.7 106.4 146.9

77.2

119.3 119.3 125.0 102.6 136.4

73.5

85

134.2 134.2 135.9 129.2 147.1

99.7

126.0 126.0 126.6 125.3 136.6

95.9

90

140.9 140.9 140.9 140.9 147.5 122.2 132.5 132.5 132.4 132.4 137.1 118.5

75

124.8 119.1 136.0

148.2

55.6

115.9 115.1 126.0

137.5

52.1

130.5 130.5 136.4 112.2 148.4

80.2

122.3 122.3 126.6 108.4 137.7

76.5

85

137.6 137.6 138.2 137.1 148.6 104.9 129.1 129.1 129.0 129.0 137.9 101.1

90

144.5 144.5 144.5 144.5 149.2 129.3 135.7 135.7 135.7 135.7 138.7 125.4

75

126.6 125.3 137.3

149.4

56.6

117.8 117.8 127.2

138.6

53.1

80

133.3 133.3 137.8 117.7 149.6

83.2

124.9 124.9 127.9 113.7 138.8

79.5

85

140.5 140.5 140.4 140.4 149.8 109.9 131.7 131.7 131.7 131.7 139.0 106.2

90

147.5 147.5 147.5 147.5 150.7 136.2 138.5 138.5 138.4 138.4 140.2 132.4 Notes:

75

128.3 128.3 138.4

80
85

90.3

82.2

80

90

32

85.9

94.6

86.5

90.8

1. All capacities shown are gross and have


not considered indoor fan heat. To obtain
135.8 135.8 139.1 123.0 150.7 86.1 127.1 127.1 129.1 119.0 139.7 82.3
net cooling, subtract indoor fan heat.
143.0 143.0 143.0 143.0 150.9 114.8 134.0 134.0 133.9 133.9 140.0 111.1 2. MBH = Total Gross Capacity
3. SHC = Sensible Heat Capacity

98.9

150.4

57.7

119.9 119.9 128.1

95.1

139.4

54.1

150.1 150.1 150.1 150.1 152.1 143.0 140.8 140.8 140.8 140.8 141.6 139.2

SS-PRC028-EN

Performance Data

Table 14. Gross Cooling Capacities (MBH) 15 Tons TTA180E Condensing Unit with 15 Tons TWE180E Air Handler (IP)
Ambient Temperature (F)
85

95

105

Entering Wet Bulb (F)

Ent
61
67
73
61
67
73
61
67
73
DB
CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

5400

6000

6600

7200

75

172.9 140.0 190.5 114.8 209.4

164.7 135.6 181.8 111.3 199.9

73.9

156.2 131.3 172.5 107.6 189.6

70.2

80

174.2 164.4 191.1 133.4 209.8 102.0 164.9 164.9 182.4 129.6 200.4

77.2

98.4

157.7 157.7 173.1 125.5 190.3

94.5

85

180.6 180.6 191.3 157.3 210.4 126.3 173.8 173.8 182.7 153.4 201.0 122.6 166.4 166.4 173.6 149.3 190.9 118.7

90

189.8 189.8 193.1 181.8 210.9 150.4 182.8 182.8 182.7 182.7 201.5 146.7 175.2 175.2 175.1 175.1 191.3 142.7

75

175.6 145.8 193.5 120.3 212.3

158.8 137.5 175.0 113.0 192.0

71.4

80

176.5 176.5 194.2 139.2 212.9 105.2 169.6 169.6 185.3 135.4 203.3 101.5 162.7 159.3 175.7 131.3 192.8

97.6

85

185.9 185.9 194.6 165.1 213.6 131.5 178.8 178.8 185.9 161.2 203.9 127.8 171.1 171.1 176.5 157.0 193.5 123.9

78.7

167.5 141.8 184.6 116.7 202.6

75.2

90

195.5 195.5 195.3 195.3 214.1 157.7 188.1 188.1 188.0 188.0 204.5 153.9 180.2 180.2 180.9 177.3 194.0 149.9

75

178.3 151.8 196.0 125.7 214.7

80

180.9 180.9 196.8 144.8 215.5 108.2 174.2 171.3 187.7 140.9 205.7 104.5 166.1 165.2 177.6 136.2 195.0 100.6

85

190.6 190.6 197.5 172.5 216.3 136.6 183.2 183.2 188.6 168.6 206.4 132.8 175.2 175.2 179.1 164.4 195.7 128.8

80.0

170.0 147.7 186.9 122.1 204.8

76.4

161.1 143.4 177.2 118.3 194.0

72.5

90

200.4 200.4 200.3 200.3 216.9 164.7 192.8 192.8 193.3 190.5 206.6 160.4 184.6 184.6 184.7 184.3 196.1 156.2

75

180.6 157.5 198.3 131.0 216.8

80

185.1 182.7 199.1 150.1 217.7 111.1 177.4 177.0 189.4 145.7 207.7 107.4 169.3 169.3 179.5 141.2 196.9 103.4

85

194.7 194.7 200.1 179.6 218.6 141.4 187.1 187.1 191.1 175.7 208.5 137.6 178.8 178.8 181.6 171.6 197.7 133.6

90

204.8 204.8 205.2 203.1 218.9 170.8 197.0 197.0 196.9 196.9 208.9 166.8 188.5 188.5 188.4 188.4 198.2 162.6

81.0

172.2 153.4 189.0 127.4 206.7

77.1

163.2 149.1 179.0 123.6 195.8

73.1

Ambient Temperature (F)


115
Ent

125
Entering Wet Bulb (F)

DB

61

67

73

61

67

73

CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

5400

6000

6600

7200

75

147.1 126.9 162.3 103.6 178.5

66.3

137.2 122.1 151.2

166.1

61.8

80

150.6 146.9 163.0 121.2 179.3

90.4

141.5 140.1 151.9 116.6 167.1

85.9

85

158.4 158.4 163.8 144.9 179.9 114.5 149.5 149.5 153.0 140.3 167.7 110.0

90

166.9 166.9 167.7 163.6 180.3 138.5 157.7 157.7 157.9 156.6 168.0 133.3

75

149.5 133.0 164.6 109.0 180.5

67.3

139.4 128.2 153.2 104.6 168.0

62.6

80

154.2 153.0 165.0 126.4 181.6

93.4

145.0 145.0 153.7 121.4 169.1

88.9

85

162.7 162.7 166.5 152.6 182.3 119.6 153.4 153.4 153.3 153.3 169.8 115.1

90

171.6 171.6 171.7 170.8 182.5 145.1 161.9 161.9 161.8 161.8 170.3 140.3

75

151.7 138.9 166.6 114.3 182.4

68.0

139.5 139.5 154.9 109.9 169.5

65.0

80

157.5 157.5 167.0 131.5 183.5

96.4

148.2 148.2 155.5 126.6 170.8

91.8

85

166.6 166.6 166.4 166.4 184.3 124.6 156.9 156.9 156.7 156.7 171.6 120.0

90

175.6 175.6 175.5 175.5 184.7 151.8 165.6 165.6 165.5 165.5 172.3 147.0 Notes:

75

153.7 144.6 168.2 119.6 183.9

80
85
90

99.3

1. All capacities shown are gross and have


not considered indoor fan heat. To obtain
160.6 160.6 168.8 136.6 185.2 99.2 151.0 151.0 157.2 131.6 172.3 94.6
net cooling, subtract indoor fan heat.
169.9 169.9 169.8 169.8 186.0 129.3 159.9 159.9 160.8 155.6 172.7 123.9 2. MBH = Total Gross Capacity
3. SHC = Sensible Heat Capacity

70.5

142.1 142.1 156.4 113.8 170.8

66.3

179.2 179.2 179.1 179.1 186.7 158.2 168.8 168.8 168.7 168.7 174.1 153.4

SS-PRC028-EN

33

Performance Data

Table 15. Gross Cooling Capacities (MBH) 15 Tons TTA180E Condensing Unit with 20 Tons TWE240E Air Handler (IP)
Ambient Temperature (F)
85

95

105

Entering Wet Bulb (F)

Ent
61
67
73
61
67
73
61
67
73
DB
CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

6400

6700

7000

7300

75

185.4 161.3 203.8 127.6 223.7

80

189.9 186.9 204.3 153.2 224.1 113.8 181.9 181.1 194.7 149.2 213.8 110.0 173.5 173.5 184.4 144.6 202.7 106.0

82.9

176.7 157.2 194.2 123.9 213.4

79.4

167.5 152.8 184.0 119.9 202.2

75.4

85

199.5 199.5 205.5 183.8 224.7 144.4 191.7 191.7 196.2 179.8 214.3 140.5 183.4 183.4 186.4 175.7 203.2 136.5

90

209.9 209.9 210.6 207.7 225.2 174.9 201.9 201.9 202.1 201.9 214.7 170.7 193.3 193.3 193.2 193.2 203.8 166.5

75

186.7 164.8 205.0 130.3 224.9

80

191.8 190.4 205.5 156.5 225.4 115.5 183.7 183.7 195.7 152.1 215.0 111.7 175.4 175.4 185.5 147.8 203.8 107.7

85

201.9 201.9 207.0 188.2 225.9 147.3 194.0 194.0 197.7 184.3 215.5 143.5 185.5 185.5 185.3 185.3 204.3 139.4

83.6

177.9 160.7 195.3 126.5 214.4

80.0

168.7 156.3 185.0 122.5 203.1

76.2

90

212.5 212.5 212.8 211.9 226.3 178.7 204.4 204.4 204.2 204.2 216.0 174.7 195.5 195.5 195.4 195.4 204.9 170.6

75

187.9 168.3 206.1 133.0 226.0

80

193.5 193.5 206.5 159.4 226.5 117.3 185.7 185.7 196.8 155.2 216.0 113.4 177.3 177.3 186.5 150.9 204.7 109.4

85

204.2 204.2 208.5 192.5 227.1 150.2 196.1 196.1 199.1 188.6 216.6 146.3 187.5 187.5 187.3 187.3 205.2 142.2

84.3

179.1 164.1 196.4 129.2 215.4

80.5

169.9 159.8 185.9 125.2 204.0

76.9

90

214.9 214.9 214.8 214.8 227.6 182.6 206.6 206.6 206.5 206.5 217.2 178.7 197.6 197.6 197.5 197.5 206.1 174.5

75

189.1 171.7 207.2 135.7 227.0

80

195.5 195.5 207.6 162.4 227.6 118.9 187.5 187.5 197.9 158.3 217.0 115.1 179.0 179.0 187.5 153.9 205.6 111.0

85

206.3 206.3 209.9 196.8 228.2 153.0 198.1 198.1 198.0 198.0 217.5 149.1 189.3 189.3 189.1 189.1 206.1 145.0

90

217.1 217.1 217.1 217.1 228.8 186.5 208.7 208.7 208.6 208.6 218.3 182.5 199.6 199.6 199.6 199.6 207.1 178.4

84.9

180.3 167.6 197.4 131.9 216.2

81.4

168.8 168.8 186.8 127.9 204.8

77.5

Ambient Temperature (F)


115
Ent
DB

125
Entering Wet Bulb (F)

61

67

73

61

67

73

CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

6400

6700

7000

7300

75

157.7 148.3 172.9 115.6 190.0

145.8 145.8 160.8 111.0 176.7

67.1

80

164.7 164.7 173.5 140.1 190.7 101.7 154.9 154.9 161.5 135.2 177.5

97.0

85

174.3 174.3 174.1 174.1 191.2 132.2 164.2 164.2 165.2 159.6 178.0 127.5

90

183.9 183.9 183.8 183.8 192.0 162.1 173.4 173.4 173.3 173.3 179.1 157.4

75

156.8 156.8 173.8 118.3 190.9

148.5 142.0 161.6 113.6 177.4

67.7

80

166.5 166.5 174.5 143.2 191.7 103.4 156.5 156.5 162.5 138.3 178.3

98.7

85

176.2 176.2 176.1 176.1 192.2 135.0 165.9 165.9 166.7 162.5 178.9 130.4

90

186.0 186.0 185.9 185.9 193.1 166.2 175.3 175.3 175.2 175.2 180.1 161.4

75

158.4 158.4 174.7 120.9 191.7

80

168.2 168.2 175.4 146.3 192.5 105.1 158.0 158.0 163.3 141.3 179.1 100.4

85

178.1 178.0 179.2 174.4 193.0 137.9 167.6 167.6 168.0 165.4 179.4 132.6

90

187.9 187.9 187.8 187.8 194.1 170.1 177.1 177.1 177.0 177.0 181.2 165.3 Notes:

75

159.9 159.9 175.4 123.6 192.5

80
85
90

34

71.5

72.2

72.8

149.7 144.3 162.3 116.3 178.1

68.4

1. All capacities shown are gross and have


not considered indoor fan heat. To obtain
169.8 169.8 176.3 149.3 193.3 106.7 159.5 159.5 164.1 144.4 179.8 102.0
net cooling, subtract indoor fan heat.
179.8 179.8 180.6 176.1 193.9 140.7 169.1 169.1 169.3 168.3 180.2 135.3 2. MBH = Total Gross Capacity
3. SHC = Sensible Heat Capacity

73.5

150.8 146.5 163.0 118.9 178.8

69.0

189.8 189.8 189.6 189.6 195.2 174.0 178.7 178.7 178.7 178.7 182.2 169.3

SS-PRC028-EN

Performance Data

Table 16. Gross Cooling Capacities (MBH) One Compressor - 15 Tons TTA180F Condensing Unit with 15 Tons TWE180E
Air Handler (IP)
Ambient Temperature (F)
85

95

105

Entering Wet Bulb (F)

Ent
61
67
73
61
67
73
61
67
73
DB
CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

5400

6000

6600

7200

75

106.4 106.4 113.7

123.5

48.4

101.7 101.7 108.0

117.6

46.4

110.6

43.2

80

112.8 112.8 114.6 105.2 124.1

84.8

73.4

107.8 107.8 109.0 103.1 117.6

71.1

102.5 102.5 103.0 100.8 110.7

63.6

85

119.1 119.1 119.1 119.1 124.1

97.8

113.5 113.5 113.5 113.5 117.7

95.7

107.7 107.7 107.7 107.7 111.7

87.3

90

124.8 124.8 124.7 124.7 125.4 122.9 120.1 120.1 120.1 120.1 120.1 120.1 114.8 114.8 114.8 114.8 114.8 114.8

75

108.4 108.4 114.7

124.3

49.7

103.6 103.6 108.9

118.4

46.6

80

114.9 114.9 115.9 111.0 124.9

76.6

109.9 109.9 110.3 108.9 118.4

74.3

85

121.0 121.0 121.0 121.0 125.1 103.0 115.5 115.5 115.5 115.5 119.9 101.3 109.5 109.5 108.8 108.8 114.4 110.2

89.6

82.8

87.7

96.6

99.5

96.6

99.5

101.9

102.7

75.4

111.3

44.2

104.0 104.0 104.0 104.0 111.4

78.9

63.6

90

127.4 127.4 127.4 127.4 127.3 127.3 122.4 122.4 122.4 122.4 122.3 122.3 116.9 116.9 116.9 116.9 116.9 116.9

75

110.2 110.2 115.5

125.0

49.6

107.4 107.4 109.6

119.1

47.5

80

116.8 116.8 117.1 116.7 126.0

78.9

111.6 111.6 111.6 111.6 119.1

76.6

85

122.8 122.8 122.8 122.8 126.0 108.0 117.2 117.2 117.2 117.2 120.8 106.3 111.9 111.9 110.2 110.2 114.8 100.0

94.4

92.5

112.0

45.1

105.4 105.4 105.4 105.4 113.0

99.8

99.8

103.3

82.3

75.0

90

129.5 129.5 129.5 129.5 129.4 129.4 124.3 124.3 124.3 124.3 124.2 124.2 118.6 118.6 118.6 118.6 118.6 118.6

75

111.4 111.4 116.3

125.6

52.2

106.6 106.6 110.3

119.6

48.4

101.0 101.0 103.9

113.0

48.1

80

118.6 118.6 118.5 118.5 126.5

81.5

112.9 112.9 112.9 112.9 119.6

79.3

106.6 106.6 106.6 106.6 114.1

76.0

85

125.5 125.5 125.4 125.4 126.8 112.8 119.9 119.9 119.8 119.8 121.6 105.0 112.7 112.7 112.1 112.1 115.8 100.5

90

131.8 131.8 131.8 131.8 131.2 131.2 125.9 125.9 125.9 125.9 125.9 125.9 120.1 120.1 120.1 120.1 120.1 120.1

99.1

97.3

85.6

Ambient Temperature (F)


115
Ent

125
Entering Wet Bulb (F)

DB

61

67

73

61

67

73

CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

5400

6000

75

91.0

91.0

95.2

72.8

103.0

35.6

84.9

84.9

87.2

69.8

95.5

29.0

80

96.1

96.1

96.1

96.1

104.0

55.0

89.5

89.5

88.0

76.0

97.0

48.0

85

102.7 102.7 101.6 101.6 106.5

79.0

95.0

95.0

92.0

86.0

100.0

72.0

90

110.9 110.9 110.8 110.8 110.8 110.8 101.0 101.0

99.0

95.0

106.0 106.0

75

92.6

92.6

95.5

76.2

103.6

36.1

85.2

85.2

87.7

73.3

87.8

70.0

80

97.6

97.6

97.6

97.6

104.0

60.9

89.1

89.1

89.8

89.8

90.4

80.7

85

103.7 103.7 102.5 102.5 106.0

85.8

95.3

95.3

94.4

94.4

95.0

91.4

90

110.7 110.7 110.6 110.6 110.6 110.6 103.0 103.0 101.9 101.9 102.1 102.1

75
6600

93.9

96.0

79.6

106.0

39.9

87.4

87.4

89.0

76.4

99.8

35.0

98.6

98.6

107.1

69.8

93.6

93.6

92.7

92.7

101.0

65.1

85

106.1 106.1 104.0 104.0 108.9

93.7

99.8

99.8

97.3

97.3

102.9

88.2

90

112.2 112.2 112.2 112.2 112.2 112.2 106.0 106.0 105.0 105.0 106.1 106.1 Notes:

100.0 100.0

75
7200

93.9

80

95.0

95.0

96.5

82.8

105.9

41.0

99.3

99.3

87.0

87.0

89.8

79.1

98.4

33.9

93.9

93.9

92.5
97.6

92.5

99.4

59.8

97.6

101.3

85.4

80

101.3 101.3

107.3

67.4

85

107.7 107.7 105.1 105.1 108.8

93.1

90

113.5 113.5 113.5 113.5 113.5 113.5 106.2 106.2 106.5 106.5 105.2 107.0

SS-PRC028-EN

100.5 100.5

1. All capacities shown are gross and have


not considered indoor fan heat. To obtain
net cooling, subtract indoor fan heat.
2. MBH = Total Gross Capacity
3. SHC = Sensible Heat Capacity

35

Performance Data

Table 17. Gross Cooling Capacities (MBH) Both Compressors - 15 Tons TTA180F Condensing Unit with 15 Tons TWE180E
Air Handler (IP)
Ambient Temperature (F)
85

95

105

Entering Wet Bulb (F)

Ent
61
67
73
61
67
73
61
67
73
DB
CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

5400

6000

6600

7200

75

174.2 141.0 190.9 115.5 208.8

166.3 136.8 182.6 112.1 199.6

73.9

158.1 132.6 173.5 108.5 189.6

70.5

80

175.4 164.8 191.7 134.1 209.4 102.1 168.2 161.1 183.4 130.4 200.3

77.2

98.6

160.4 157.1 174.4 126.5 190.4

94.8

85

181.7 181.7 192.0 157.9 210.2 126.6 175.0 175.0 183.7 154.1 201.1 123.0 167.8 167.8 174.7 150.0 191.2 119.2

90

190.6 190.6 193.8 181.9 210.9 150.9 183.8 183.8 185.8 178.2 201.7 147.3 176.4 176.4 177.3 174.2 191.8 143.5

75

176.8 146.7 193.8 121.0 211.5

160.5 138.5 176.0 113.9 191.8

71.6

80

179.1 173.2 194.7 139.9 212.4 105.3 171.7 169.4 186.1 136.2 203.0 101.8 163.7 163.7 176.8 132.3 192.8

98.0

85

186.8 186.8 195.1 165.4 213.3 131.8 179.9 179.9 186.5 161.5 203.9 128.2 172.4 172.4 177.5 157.4 193.7 124.4

78.6

169.0 142.7 185.2 117.6 202.0

75.3

90

196.1 196.1 197.7 191.7 214.0 158.2 188.9 188.9 189.7 187.9 204.6 154.6 181.1 181.1 181.0 181.0 194.4 150.7

75

179.3 152.4 196.3 126.4 213.8

80

182.4 181.1 197.3 145.5 214.9 108.3 174.9 174.9 188.4 141.7 205.3 104.7 167.4 167.4 178.6 136.9 194.9 100.9

85

191.3 191.3 197.8 172.5 215.9 136.9 184.2 184.2 189.2 168.7 206.2 133.2 176.4 176.4 180.0 164.5 195.9 129.4

80.0

171.3 148.4 187.5 123.0 204.1

76.4

162.7 144.2 178.0 119.3 193.6

72.7

90

200.8 200.8 201.4 201.1 216.6 165.2 193.4 193.4 193.3 193.3 206.6 160.5 185.3 185.3 185.2 185.2 196.2 156.3

75

181.5 157.8 198.4 131.8 215.6

80

185.5 185.5 199.0 150.0 217.1 111.2 178.4 178.4 190.1 146.0 207.3 107.6 170.6 170.6 180.5 141.7 196.7 103.8

85

195.3 195.3 200.3 179.4 218.1 141.7 187.9 187.9 191.6 175.5 208.3 138.0 179.8 179.8 182.3 171.4 197.7 134.1

90

205.1 205.1 205.0 205.0 218.5 170.6 197.4 197.4 197.3 197.3 208.7 166.7 189.0 189.0 188.9 188.9 198.2 162.5

81.0

173.3 153.8 189.5 128.3 205.7

77.4

164.7 149.6 179.8 124.6 195.0

74.4

Ambient Temperature (F)


115
Ent
DB

125
Entering Wet Bulb (F)

61

67

73

61

67

73

CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

5400

6000

6600

7200

75

149.2 128.2 163.8 104.6 178.8

66.6

139.5 123.4 153.0 100.5 166.8

62.4

80

151.9 151.9 164.6 122.4 179.7

90.9

143.4 143.4 153.8 117.9 167.9

86.5

85

160.1 160.1 165.1 145.6 180.5 115.2 151.3 151.3 154.7 140.9 168.7 110.8

90

168.2 168.2 168.1 168.1 181.1 139.4 159.1 159.1 159.1 159.1 169.0 134.0

75

151.5 134.1 166.0 110.0 180.7

67.7

141.7 129.3 155.0 105.8 168.3

64.0

80

155.8 155.8 166.8 128.1 181.9

93.9

147.0 147.0 155.5 122.5 169.8

89.6

85

164.2 164.2 167.8 153.0 182.8 120.3 155.0 155.0 157.2 148.2 170.7 115.9

90

172.6 172.6 172.6 172.6 183.1 145.5 163.1 163.1 163.1 163.1 171.1 140.6

75

153.6 139.7 167.8 115.4 182.1

69.4

143.6 134.8 156.6 111.1 169.7

65.3

80

159.2 159.2 168.4 132.4 183.8

96.9

150.0 150.0 157.2 127.5 171.5

92.5

85

167.8 167.8 170.2 160.1 184.7 125.3 158.3 158.3 159.4 155.2 172.4 120.8

90

176.5 176.5 176.4 176.4 185.1 151.8 166.6 166.6 166.5 166.5 172.9 147.0 Notes:

75

155.5 145.1 169.4 120.7 183.6

80
85
90

36

1. All capacities shown are gross and have


not considered indoor fan heat. To obtain
162.1 162.1 170.1 137.2 185.3 99.7 152.7 152.7 158.7 132.2 172.8 95.2
net cooling, subtract indoor fan heat.
171.0 171.0 172.4 166.9 186.3 130.0 161.2 161.2 161.1 161.1 173.4 124.3 2. MBH = Total Gross Capacity
3. SHC = Sensible Heat Capacity

70.7

145.4 140.2 158.0 116.4 171.0

66.6

179.9 179.9 179.8 179.8 186.8 158.0 169.7 169.7 169.7 169.7 174.6 153.1

SS-PRC028-EN

Performance Data

Table 18. Gross Cooling Capacities (MBH) 20 Tons TTA240E Condensing Unit with 20 Tons TWE240E Air Handler (IP)
Ambient Temperature (F)
85

95

105

Entering Wet Bulb (F)

Ent
61
67
73
61
67
73
61
67
73
DB
CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

7200

8000

8800

9600

75

245.0 197.2 270.0 160.0 297.4 109.4 234.5 192.0 258.2 155.2 284.3 104.7 222.7 186.1 245.4 150.0 270.0

80

247.5 231.4 270.8 188.0 297.6 144.0 237.4 226.1 259.0 182.8 284.5 139.0 226.5 220.5 246.3 177.3 270.3 133.6

99.6

85

255.7 255.7 271.6 222.1 298.1 177.9 246.5 246.5 259.7 216.5 285.1 172.8 236.5 236.5 247.1 210.8 271.0 167.3

90

268.7 268.7 274.4 255.7 298.7 211.6 259.2 259.2 263.2 250.5 285.7 206.4 248.8 248.8 251.3 244.8 271.6 200.9

75

249.1 206.1 274.4 167.3 301.8 111.3 238.3 200.7 262.2 162.4 288.2 106.6 226.6 194.8 249.1 157.2 273.6 101.4

80

253.0 243.7 275.3 196.4 302.1 148.6 240.7 240.7 263.1 191.1 288.6 143.5 230.7 230.7 250.0 185.5 274.0 138.0

85

263.4 263.4 276.1 233.0 302.7 185.4 253.8 253.8 264.2 227.5 289.2 180.3 243.3 243.3 251.5 221.7 274.7 174.8

90

276.9 276.9 280.4 270.1 303.4 222.1 266.9 266.9 266.6 266.6 289.9 216.9 255.9 255.9 255.7 255.7 275.5 211.4

75

253.0 214.7 278.1 174.6 305.6 113.3 242.0 209.2 265.6 169.6 291.6 108.3 230.0 203.3 252.1 164.4 276.6 102.8

80

256.3 256.3 279.1 204.4 305.9 153.0 246.7 246.7 266.6 199.1 292.0 147.8 236.1 236.1 253.1 193.4 277.1 142.3

85

270.1 270.1 280.4 243.6 306.6 192.7 260.1 260.1 268.3 238.2 292.7 187.5 249.2 249.2 255.3 232.3 277.9 181.9

90

284.0 284.0 283.8 283.8 307.3 232.2 273.6 273.6 273.4 273.4 293.6 227.0 262.2 262.2 262.0 262.0 278.4 220.9

75

256.5 222.9 281.3 181.8 308.8 114.9 245.2 217.4 268.5 176.8 294.5 109.6 233.1 211.4 254.8 171.5 279.2 104.2

80

261.9 261.9 282.3 212.1 309.2 157.2 251.9 251.9 269.5 206.7 295.0 152.0 241.0 241.0 255.4 200.5 279.8 146.4

85

276.1 276.1 284.4 253.9 309.9 199.7 265.7 265.7 272.1 248.4 295.8 194.4 254.4 254.4 258.9 242.5 280.6 188.8

90

290.4 290.4 290.2 290.2 310.8 242.0 279.5 279.5 279.3 279.3 296.4 236.1 267.7 267.7 267.5 267.5 281.4 230.2

Ambient Temperature (F)


115
Ent

125
Entering Wet Bulb (F)

DB

61

67

73

61

67

73

CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

7200

8000

8800

9600

75

210.3 179.8 231.5 144.4 254.5

80

213.7 213.7 232.4 171.3 254.8 127.8 202.0 201.4 216.8 164.8 237.6 121.5

85

225.4 225.4 233.6 204.6 255.6 161.5 212.9 212.9 218.6 197.8 238.4 155.1

90

237.3 237.3 237.0 237.0 256.3 195.1 224.2 224.2 224.5 224.2 239.3 188.8

75

213.9 188.5 234.7 151.6 257.6

80

219.9 219.4 235.6 179.5 258.1 132.2 206.9 206.9 219.3 172.4 240.5 125.8

85

231.6 231.6 237.6 215.5 258.9 168.9 218.5 218.5 222.3 208.6 241.3 162.5

90

243.9 243.9 243.7 243.7 259.8 205.6 230.2 230.2 230.0 230.0 242.0 198.1

75

217.1 196.9 237.5 158.7 260.3

80

224.5 224.5 238.1 186.8 260.9 136.4 211.4 211.4 222.0 179.8 242.9 130.0

85

237.1 237.1 241.3 225.9 261.7 176.0 223.4 223.4 223.2 223.2 243.7 169.5

90

249.6 249.6 249.4 249.4 262.5 214.6 235.4 235.4 235.2 235.2 244.9 207.6 Notes:

75

220.0 204.9 239.8 165.8 262.5

80
85
90

94.1

95.6

97.0

196.5 173.0 215.9 138.3 237.1

199.8 181.6 218.7 145.4 239.8

202.8 189.9 221.1 152.5 241.9

88.0

89.3

91.8

1. All capacities shown are gross and have


not considered indoor fan heat. To obtain
229.0 229.0 240.7 194.0 263.3 140.5 215.4 215.4 224.3 186.9 244.9 134.0
net cooling, subtract indoor fan heat.
241.8 241.8 244.6 236.1 264.1 182.9 227.7 227.7 227.5 227.5 245.8 176.3 2. MBH = Total Gross Capacity
3. SHC = Sensible Heat Capacity

99.7

205.5 197.9 223.2 159.5 243.8

93.6

254.7 254.7 254.5 254.5 265.3 223.8 240.0 240.0 239.8 239.8 247.5 216.8

SS-PRC028-EN

37

Performance Data

Table 19. Gross Cooling Capacities (MBH) One Compressor - 20 Tons TTA240F Condensing Unit with 20 Tons TWE240E
Air Handler (IP)
Ambient Temperature (F)
85

95

105

Entering Wet Bulb (F)

Ent
61
67
73
61
67
73
61
67
73
DB
CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

7200

8000

8800

9600

75

143.7 136.8 158.0 116.7 173.8

67.2

137.4 133.9 150.6 113.9 165.4

64.5

130.5 130.5 142.5 109.8 156.3

61.6

80

151.0 151.0 158.2 129.6 173.9

93.8

145.0 145.0 150.8 126.6 165.6

90.9

138.4 138.4 142.7 123.2 156.5

87.7

85

159.6 159.6 160.0 158.0 174.2 122.2 153.3 153.3 153.2 153.2 165.8 119.3 146.3 146.3 146.2 146.2 156.7 116.1

90

168.2 168.2 168.1 168.1 174.3 149.8 161.6 161.6 161.5 161.5 166.0 146.7 154.2 154.2 154.2 154.2 157.1 143.4

75

145.9 143.5 159.7 122.5 175.4

69.0

139.6 139.6 152.1 119.7 166.9

66.3

133.1 133.1 143.8 116.6 157.6

63.4

80

154.3 154.3 160.0 135.6 175.7

97.2

148.1 148.1 152.4 132.4 167.1

94.2

141.2 141.2 144.1 129.1 157.8

91.0

85

163.1 163.1 163.0 163.0 175.9 127.8 156.6 156.6 156.5 156.5 167.3 124.5 149.3 149.3 149.2 149.2 158.0 121.1

90

172.0 172.0 171.9 171.9 176.2 157.4 165.1 165.1 165.0 165.0 167.9 154.3 157.4 157.4 157.3 157.3 158.9 151.0

75

148.2 148.2 161.2 129.3 176.8

142.1 142.1 153.4 126.5 168.1

68.0

135.4 135.4 145.0 123.4 158.7

65.1

80

157.2 157.2 161.4 141.2 177.1 100.3 150.7 150.7 153.7 138.1 168.4

97.3

143.6 143.6 145.5 134.7 159.0

94.1

85

166.2 166.2 166.1 166.1 177.3 132.7 159.4 159.4 159.3 159.3 168.6 129.6 151.9 151.9 151.8 151.8 159.1 126.1

70.8

90

175.3 175.3 175.2 175.2 178.0 164.7 168.1 168.1 168.0 168.0 169.6 161.6 160.1 160.1 160.0 160.0 160.6 158.2

75

150.5 150.5 162.4 136.1 178.0

137.3 137.3 145.9 129.7 159.6

66.8

80

159.7 159.7 162.8 146.6 178.4 103.4 153.1 153.1 155.1 143.5 169.5 100.3 145.7 145.7 146.8 140.1 159.9

97.1

85

168.9 168.9 168.8 168.8 178.6 137.6 161.9 161.9 161.8 161.8 169.7 134.4 154.1 154.1 154.1 154.1 160.1 131.0

90

178.2 178.2 178.1 178.1 179.7 171.7 170.7 170.7 170.6 170.6 171.2 168.6 162.1 162.1 162.1 162.1 162.0 162.0

72.5

144.2 144.2 154.6 133.3 169.2

69.8

Ambient Temperature (F)


115
Ent
DB

125
Entering Wet Bulb (F)

61

67

73

61

67

73

CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

7200

8000

8800

9600

75

123.6 123.6 133.7 106.5 146.4

58.5

115.8 115.8 124.0 103.0 135.6

55.1

80

131.1 131.1 133.9 119.6 146.7

84.3

122.9 122.9 124.5 115.8 135.9

80.7

85

138.6 138.6 138.5 138.5 146.8 112.2 130.0 130.0 129.9 129.9 136.1 108.4

90

146.1 146.1 146.1 146.1 147.6 139.9 137.0 137.0 137.0 137.0 137.4 136.0

75

125.9 125.9 134.8 113.3 147.5

60.2

117.9 117.9 124.9 109.3 136.6

56.8

80

133.6 133.6 135.3 125.5 147.8

87.6

125.2 125.2 125.9 121.6 136.9

83.9

85

141.3 141.3 141.2 141.2 148.0 117.5 132.4 132.4 132.3 132.3 137.1 113.6

90

148.9 148.9 148.9 148.9 149.4 147.4 139.5 139.5 139.5 139.5 139.4 139.4

75

127.9 127.9 135.8 119.6 148.5

61.9

119.7 119.7 125.8 115.8 137.4

58.5

80

135.8 135.8 136.7 131.1 148.8

90.7

127.1 127.1 127.0 127.0 137.7

87.0

85

143.6 143.6 143.5 143.5 149.0 122.5 134.4 134.4 134.4 134.4 137.9 118.5

90

151.4 151.4 151.3 151.3 151.2 151.2 141.6 141.6 141.6 141.6 141.5 141.5 Notes:

75

129.7 129.7 136.7 126.1 149.3

80
85
90

38

1. All capacities shown are gross and have


not considered indoor fan heat. To obtain
137.7 137.7 138.0 136.5 149.7 93.6 128.8 128.8 128.7 128.7 138.5 89.9
net cooling, subtract indoor fan heat.
145.6 145.6 145.6 145.6 149.9 127.3 136.2 136.2 136.1 136.1 138.7 123.3 2. MBH = Total Gross Capacity
3. SHC = Sensible Heat Capacity

63.6

121.3 121.3 126.6

98.1

138.1

60.2

152.7 152.7 152.7 152.7 152.7 152.7 143.5 143.5 143.4 143.4 143.3 143.3

SS-PRC028-EN

Performance Data

Table 20. Gross Cooling Capacities (MBH) Both Compressors - 20 Tons TTA240F Condensing Unit with 20 Tons TWE240E
Air Handler (IP)
Ambient Temperature (F)
85

95

105

Entering Wet Bulb (F)

Ent
61
67
73
61
67
73
61
67
73
DB
CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

7200

8000

8800

9600

75

237.0 189.3 261.7 156.2 288.4 106.0 226.8 184.2 250.2 151.6 275.6 101.5 215.5 178.8 237.7 146.6 261.6

80

238.8 221.9 262.0 180.5 288.4 139.0 229.0 216.9 250.6 175.5 275.6 134.0 218.4 211.6 238.1 170.2 261.7 128.8

96.6

85

246.3 246.3 262.4 212.6 288.5 170.9 237.5 237.5 250.9 207.6 275.7 165.9 227.8 227.8 238.6 202.2 261.9 160.7

90

258.6 258.6 264.4 244.8 288.8 202.7 249.5 249.5 253.6 239.8 276.0 197.7 239.4 239.4 241.9 234.5 262.2 192.4

75

241.2 197.7 265.9 163.6 292.9 108.1 230.5 192.6 254.1 158.8 279.6 103.4 218.9 187.2 241.2 153.8 265.2

80

244.0 233.2 266.4 188.2 292.8 143.2 234.0 228.2 254.5 183.2 279.6 138.2 223.2 222.9 241.7 177.7 265.3 132.9

85

253.6 253.6 266.7 223.0 293.0 177.9 244.4 244.4 255.1 218.0 279.7 172.8 234.2 234.2 242.4 212.3 265.5 167.5

98.5

90

266.4 266.4 270.1 258.1 293.3 212.4 256.7 256.7 259.0 253.0 280.0 207.3 246.2 246.2 246.0 246.0 265.8 201.9

75

244.7 205.8 269.5 170.8 296.4 110.0 233.8 200.7 257.3 166.0 282.9 104.9 222.0 194.9 244.1 160.9 268.2

80

248.7 244.1 270.0 195.6 296.5 147.2 237.7 237.7 257.9 190.5 282.9 142.2 227.5 227.5 244.7 185.0 268.3 136.8

85

260.0 260.0 270.7 233.1 296.7 184.5 250.4 250.4 258.8 227.6 283.1 179.4 239.8 239.8 246.1 222.1 268.5 174.0

99.6

90

273.2 273.2 275.2 270.8 297.0 221.6 263.1 263.1 263.0 263.0 283.5 216.5 252.1 252.1 252.0 252.0 268.9 211.0

75

247.7 213.2 272.6 178.0 299.7 111.3 236.8 208.0 260.2 173.1 285.7 106.2 225.0 202.4 246.7 168.0 270.7 100.9

80

252.3 252.3 273.2 202.6 299.7 151.1 242.7 242.7 260.7 197.4 285.7 146.0 232.1 232.1 247.3 191.9 270.8 140.6

85

265.7 265.7 274.3 242.3 299.9 190.9 255.7 255.7 262.3 237.1 286.0 185.7 244.7 244.7 249.4 231.5 271.1 180.3

90

279.3 279.3 279.1 279.1 300.3 230.4 268.8 268.8 268.6 268.6 286.4 225.3 257.3 257.3 257.2 257.2 271.5 219.8

Ambient Temperature (F)


115
Ent

125
Entering Wet Bulb (F)

DB

61

67

73

61

67

73

CFM (F) MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC MBH SHC

7200

8000

8800

9600

75

203.2 173.0 224.0 141.1 246.4

80

206.9 205.9 224.5 164.4 246.5 123.1 194.3 194.3 209.3 158.0 229.6 116.9

85

217.1 217.1 225.3 196.5 246.7 155.0 204.9 204.9 210.4 189.8 229.9 148.8

90

228.2 228.2 229.3 228.7 247.1 186.7 215.6 215.6 215.4 215.4 230.2 180.4

75

206.4 181.1 227.1 148.3 249.5

80

211.5 211.5 227.6 171.9 249.7 127.2 199.3 199.3 212.0 165.5 232.3 120.9

85

222.9 222.9 228.9 206.4 249.9 161.8 210.2 210.2 213.9 199.9 232.6 155.5

90

234.4 234.4 234.3 234.3 250.2 196.1 221.1 221.1 221.0 221.0 233.0 189.8

75

209.5 188.9 229.7 155.4 252.2

80

216.3 216.3 230.3 179.1 252.3 131.1 203.6 203.6 214.3 172.6 234.5 124.8

85

228.1 228.1 232.3 216.1 252.6 168.2 214.8 214.8 217.1 209.5 234.9 161.9

90

239.9 239.9 239.7 239.7 252.9 205.2 226.0 226.0 225.9 225.9 235.6 199.0 Notes:

75

212.2 196.3 232.0 162.4 254.3

80
85
90

91.3

92.6

93.9

189.6 166.5 208.8 135.1 229.5

192.8 174.5 211.5 142.2 232.1

195.6 182.3 213.7 149.3 234.3

85.5

87.3

89.1

1. All capacities shown are gross and have


not considered indoor fan heat. To obtain
220.5 220.5 232.6 185.9 254.5 134.8 207.4 207.4 216.3 179.4 236.5 128.5
net cooling, subtract indoor fan heat.
232.6 232.6 235.4 225.4 254.9 174.5 218.8 218.8 220.0 218.8 236.9 168.1 2. MBH = Total Gross Capacity
3. SHC = Sensible Heat Capacity

96.8

198.1 189.7 215.7 156.3 236.2

90.9

244.6 244.6 244.5 244.5 255.5 214.1 230.3 230.3 230.2 230.2 237.8 207.0

SS-PRC028-EN

39

Performance Data

Table 21. Gross Cooling Capacities (MBH) 6 Tons TTA073D Condensing Unit Only (IP)
Suction Temperature (F)

Outdoor
Temp (F)
65

75

85

95

105

115

125

30

35

40

45

50

55

Head Press (psig)

248.4

262.2

269.4

276.9

284.7

292.9

Capacity (Btuh/1000)

66.4

73.5

81.0

88.7

96.7

105.0

Unit Power (kW)

4.4

4.4

4.4

4.5

4.5

4.6

Head Press (psig)

292.6

299.8

307.3

315.0

323.1

331.5

Capacity (Btuh/1000)

62.6

69.4

76.4

83.8

91.3

99.1

Unit Power (kW)

4.7

4.8

4.8

4.9

5.0

5.0

Head Press (psig)

333.3

340.8

348.6

356.7

365.1

373.7

Capacity (Btuh/1000)

58.5

65.0

71.7

78.7

85.8

93.1

Unit Power (kW)

5.2

5.3

5.3

5.4

5.5

5.5

Head Press (psig)

377.5

385.4

393.5

401.9

410.6

419.4

Capacity (Btuh/1000)

54.2

60.4

66.8

73.4

80.1

87.0

Unit Power (kW)

5.7

5.8

5.9

5.9

6.0

6.1

Head Press (psig)

425.2

433.5

442.1

450.9

459.8

469.0

Capacity (Btuh/1000)

49.7

55.6

61.7

67.9

74.3

80.8

Unit Power (kW)

6.4

6.4

6.5

6.5

6.6

6.7

Head Press (psig)

476.7

485.5

494.4

503.5

512.7

522.1

Capacity (Btuh/1000)

45.0

50.6

56.3

62.3

68.3

74.4

Unit Power (kW)

7.0

7.1

7.1

7.2

7.3

7.3

Head Press (psig)

531.8

541.1

550.3

559.6

569.0

578.4

Capacity (Btuh/1000)

40.0

45.3

50.7

56.3

61.9

67.5

Unit Power (kW)

7.8

7.8

7.9

7.9

8.0

8.0

Note: Performance data calculated at 15F subcooling and 15F superheat and does not include capacity loss due to refrigerant lines.

Figure 4. TTA073D Capacity Curve


Capacity Curves - Condensing Unit Only

COMPRESSOR HIGH SUCTION LIMIT

135
125

105
INDOOR COIL FROST LIMIT

Gross Cooling Capacity (MBH)

115

95
85
75
65

65
75
85
95
105
115
125

55
45
35
25

30

35

40

45

50

55

60

65

70

75

Saturated Suction Temperature (F)

40

SS-PRC028-EN

Performance Data

Table 22. Gross Cooling Capacities (MBH) 7.5 Tons TTA090D Condensing Unit Only (IP)
Suction Temperature (F)

Outdoor
Temp (F)
65

75

85

95

105

115

125

30

35

40

45

50

55

Head Press (psig)

263.0

279.5

287.6

296.2

305.2

314.7

Capacity (Btuh/1000)

82.1

89.4

97.5

105.9

114.6

123.7

Unit Power (kW)

5.2

5.3

5.4

5.6

5.7

5.9

Head Press (psig)

310.2

318.4

327.0

336.1

345.5

355.4

Capacity (Btuh/1000)

77.2

84.7

92.4

100.5

108.9

117.5

Unit Power (kW)

5.6

5.8

5.9

6.1

6.2

6.4

Head Press (psig)

352.3

360.9

370.0

379.5

389.4

399.7

Capacity (Btuh/1000)

72.7

79.8

87.2

94.9

102.9

111.0

Unit Power (kW)

6.2

6.4

6.5

6.7

6.8

7.0

Head Press (psig)

398.1

407.1

416.6

426.5

436.8

447.6

Capacity (Btuh/1000)

68.0

74.7

81.8

89.1

96.6

104.4

Unit Power (kW)

6.9

7.0

7.2

7.3

7.5

7.7

Head Press (psig)

447.7

457.3

467.2

477.4

488.1

499.2

Capacity (Btuh/1000)

63.1

69.5

76.2

83.0

90.2

97.5

Unit Power (kW)

7.6

7.8

7.9

8.1

8.3

8.4

Head Press (psig)

501.4

511.3

521.5

532.1

543.1

554.4

Capacity (Btuh/1000)

58.1

64.1

70.3

76.7

83.4

90.2

Unit Power (kW)

8.4

8.6

8.8

8.9

9.1

9.2

Head Press (psig)

559.0

569.2

579.6

590.3

601.3

612.4

Capacity (Btuh/1000)

52.7

58.3

64.0

69.9

76.1

82.3

Unit Power (kW)

9.4

9.5

9.7

9.8

10.0

10.1

Note: Performance data calculated at 15F subcooling and 15F superheat and does not include capacity loss due to refrigerant lines.

Figure 5. TTA090D Capacity Curve


Capacity Curves - Condensing Unit Only

COMPRESSOR HIGH SUCTION LIMIT

155
145
135

INDOOR COIL FROST LIMIT

Gross Cooling Capacity (MBH)

125
115
105
95
85

65
75
85
95
105
115
125

75
65
55
45
25

30

35

40

45

50

55

60

65

70

75

Saturated Suction Temperature (F)

SS-PRC028-EN

41

Performance Data

Table 23. Gross Cooling Capacities (MBH) 10 Tons TTA120D Condensing Unit Only (IP)
Suction Temperature (F)

Outdoor
Temp (F)
65

75

85

95

105

115

125

30

35

40

45

50

55

Head Press (psig)

255.9

262.9

270.2

278.0

286.0

294.5

Capacity (Btuh/1000)

98.8

109.9

121.5

133.5

145.9

158.7

Unit Power (kW)

6.9

7.1

7.2

7.4

7.6

7.7

Head Press (psig)

292.9

300.2

307.8

315.7

324.0

332.6

Capacity (Btuh/1000)

93.8

104.3

115.2

126.6

138.3

150.3

Unit Power (kW)

7.5

7.7

7.8

8.0

8.2

8.3

Head Press (psig)

333.5

341.1

349.0

357.1

365.6

374.3

Capacity (Btuh/1000)

88.3

98.3

108.7

119.4

130.5

141.8

Unit Power (kW)

8.2

8.4

8.5

8.7

8.8

9.0

Head Press (psig)

377.8

385.7

393.8

402.2

410.9

419.8

Capacity (Btuh/1000)

82.6

92.0

101.8

112.0

122.4

133.1

Unit Power (kW)

9.0

9.2

9.3

9.5

9.6

9.8

Head Press (psig)

425.9

434.1

442.6

451.4

460.3

469.4

Capacity (Btuh/1000)

76.5

85.4

94.7

104.3

114.2

124.2

Unit Power (kW)

9.9

10.1

10.2

10.4

10.5

10.7

Head Press (psig)

478.1

486.8

495.6

504.7

513.8

523.1

Capacity (Btuh/1000)

70.1

78.6

87.3

96.4

105.6

115.0

Unit Power (kW)

11.0

11.1

11.3

11.4

11.5

11.7

Head Press (psig)

534.6

543.9

553.1

562.5

571.8

581.3

Capacity (Btuh/1000)

63.3

71.3

79.5

88.0

96.6

105.3

Unit Power (kW)

12.1

12.2

12.4

12.5

12.6

12.7

Note: Performance data calculated at 15F subcooling and 15F superheat and does not include capacity loss due to refrigerant lines.

Figure 6. TTA120D Capacity Curve

Capacity Curves - Condensing Unit Only

COMPRESSOR HIGH SUCTION LIMIT

205
195
185
175

155
INDOOR COIL FROST LIMIT

Gross Cooling Capacity (MBH)

165

145
135
125
115
105
95
85

65
75
85
95
105
115
125

75
65
55
25

30

35

40

45

50

55

60

65

70

75

Saturated Suction Temperature (F)

42

SS-PRC028-EN

Performance Data

Table 24. Gross Cooling Capacities (MBH) 10 Tons TTA120E Condensing Unit Only (IP)
Suction Temperature (F)

Outdoor
Temp (F)
65

75

85

95

105

115

125

30

35

40

45

50

55

Head Press (psig)

253.8

260.4

267.5

274.9

282.6

290.7

Capacity (Btuh/1000)

99.4

110.4

121.8

133.7

145.9

158.5

Unit Power (kW)

6.4

6.5

6.6

6.7

6.8

6.9

Head Press (psig)

290.3

297.2

304.4

312.0

319.9

328.1

Capacity (Btuh/1000)

93.7

104.0

114.8

126.0

137.5

149.3

Unit Power (kW)

7.0

7.1

7.2

7.3

7.4

7.6

Head Press (psig)

330.4

337.5

345.0

352.8

360.8

369.2

Capacity (Btuh/1000)

87.6

97.4

107.6

118.1

129.0

140.0

Unit Power (kW)

7.7

7.8

8.0

8.1

8.2

8.4

Head Press (psig)

374.2

381.5

389.2

397.2

405.4

413.9

Capacity (Btuh/1000)

81.3

90.4

100.0

110.0

120.2

130.6

Unit Power (kW)

8.6

8.7

8.9

9.0

9.2

9.3

Head Press (psig)

421.7

429.3

437.3

445.5

453.9

462.6

Capacity (Btuh/1000)

74.7

83.3

92.3

101.7

111.2

121.0

Unit Power (kW)

9.7

9.8

9.9

10.0

10.2

10.3

Head Press (psig)

473.3

481.3

489.5

498.0

506.5

515.3

Capacity (Btuh/1000)

67.7

75.9

84.3

93.1

102.1

111.2

Unit Power (kW)

10.8

11.0

11.1

11.2

11.3

11.4

Head Press (psig)

529.1

537.5

546.0

554.6

563.4

572.3

Capacity (Btuh/1000)

60.5

68.2

76.0

84.2

92.6

101.0

Unit Power (kW)

12.1

12.3

12.4

12.5

12.6

12.7

Note: Performance data calculated at 15F subcooling and 15F superheat and does not include capacity loss due to refrigerant lines.

Figure 7.

TTA120E Capacity Curve

Capacity Curves - Condensing Unit Only

COMPRESSOR HIGH SUCTION LIMIT

200
190
180
170

150

INDOOR COIL FROST LIMIT

Gross Cooling Capacity (MBH)

160

140
130
120
110
100

65
75
85
95
105
115
125

90
80
70
60
50
25

30

35

40

45

50

55

60

65

70

75

Saturated Suction Temperature (F)

SS-PRC028-EN

43

Performance Data

Table 25. Gross Cooling Capacities (MBH) One Compressor - 10 Tons TTA120F Condensing Unit Only (IP)
Suction Temperature (F)

Outdoor
Temp (F)
65

75

85

95

105

115

125

30

35

40

45

50

55

Head Press (psig)

216.1

219.4

222.9

226.6

230.3

234.4

Capacity (Btuh/1000)

48.2

54.2

60.8

67.7

74.7

82.3

Unit Power (kW)

3.5

3.5

3.5

3.5

3.5

3.5

Head Press (psig)

250.3

253.7

257.3

261.1

265.1

269.2

Capacity (Btuh/1000)

45.9

51.6

57.7

64.3

71.1

78.3

Unit Power (kW)

3.8

3.8

3.8

3.8

3.8

3.9

Head Press (psig)

288.2

291.7

295.4

299.3

303.4

307.5

Capacity (Btuh/1000)

43.4

48.9

54.6

60.8

67.3

74.0

Unit Power (kW)

4.1

4.1

4.2

4.2

4.2

4.2

Head Press (psig)

329.7

333.4

337.2

341.1

345.3

349.5

Capacity (Btuh/1000)

40.8

46.0

51.4

57.2

63.3

69.7

Unit Power (kW)

4.5

4.5

4.6

4.6

4.6

4.6

Head Press (psig)

375.2

378.9

382.8

386.9

391.1

395.5

Capacity (Btuh/1000)

37.9

42.9

48.1

53.5

59.2

65.1

Unit Power (kW)

5.0

5.0

5.0

5.1

5.1

5.1

Head Press (psig)

424.6

428.5

432.6

436.7

441.0

445.5

Capacity (Btuh/1000)

34.9

39.6

44.5

49.6

54.9

60.4

Unit Power (kW)

5.5

5.5

5.6

5.6

5.6

5.6

Head Press (psig)

478.3

482.4

486.5

490.7

495.0

499.3

Capacity (Btuh/1000)

31.6

36.1

40.7

45.4

50.3

55.3

Unit Power (kW)

6.1

6.1

6.1

6.2

6.2

6.2

Note: Performance data calculated at 15F subcooling and 15F superheat and does not include capacity loss due to refrigerant lines.

Figure 8. TTA120F - One Compressor - Capacity Curve

Capacity Curves - Condensing Unit Only

COMPRESSOR HIGH SUCTION LIMIT

110

100

80
INDOOR COIL FROST LIMIT

Gross Cooling Capacity (MBH)

90

70

60

50

65
75
85
95
105
115
125

40

30

20
25

30

35

40

45

50

55

60

65

70

75

Saturated Suction Temperature (F)

44

SS-PRC028-EN

Performance Data

Table 26. Gross Cooling Capacities (MBH) Both Compressors - 10 Tons TTA120F Condensing Unit Only (IP)
Suction Temperature (F)

Outdoor
Temp (F)
65

75

85

95

105

115

125

30

35

40

45

50

55

Head Press (psig)

255.3

262.3

269.6

277.3

285.3

293.7

Capacity (Btuh/1000)

100.9

112.0

123.6

135.8

148.3

161.3

Unit Power (kW)

6.5

6.6

6.7

6.8

7.0

7.1

Head Press (psig)

291.9

299.1

306.6

314.5

322.7

331.3

Capacity (Btuh/1000)

95.7

106.2

117.3

128.7

140.6

152.9

Unit Power (kW)

7.2

7.3

7.4

7.6

7.7

7.9

Head Press (psig)

331.9

339.4

347.2

355.3

363.7

372.5

Capacity (Btuh/1000)

90.2

100.2

110.6

121.5

132.8

144.3

Unit Power (kW)

8.0

8.1

8.3

8.4

8.6

8.7

Head Press (psig)

375.4

383.2

391.3

399.6

408.3

417.2

Capacity (Btuh/1000)

84.4

93.9

103.8

114.1

124.7

135.5

Unit Power (kW)

9.0

9.1

9.2

9.4

9.5

9.6

Head Press (psig)

422.5

430.6

439.0

447.6

456.5

465.6

Capacity (Btuh/1000)

78.2

87.3

96.6

106.3

116.3

126.5

Unit Power (kW)

10.0

10.1

10.3

10.4

10.5

10.7

Head Press (psig)

473.4

481.9

490.6

499.4

508.5

517.7

Capacity (Btuh/1000)

71.8

80.4

89.2

98.4

107.7

117.2

Unit Power (kW)

11.2

11.3

11.4

11.5

11.6

11.8

Head Press (psig)

527.9

536.8

545.8

554.9

564.1

573.3

Capacity (Btuh/1000)

65.0

73.1

81.4

89.9

98.6

107.4

Unit Power (kW)

12.4

12.5

12.6

12.7

12.8

12.9

Note: Performance data calculated at 15F subcooling and 15F superheat and does not include capacity loss due to refrigerant lines.

Figure 9. TTA120F - Both Compressors - Capacity Curve

Capacity Curves - Condensing Unit Only

COMPRESSOR HIGH SUCTION LIMIT

210
200
190
180

160
INDOOR COIL FROST

Gross Cooling Capacity (MBH)

170

150
140
130
120
110
100

65
75
85
95
105
115
125

90
80
70
60
50
25

30

35

40

45

50

55

60

65

70

75

Saturated Suction Temperature (F)

SS-PRC028-EN

45

Performance Data

Table 27. Gross Cooling Capacities (MBH) 12.5 Tons TTA150E Condensing Unit Only (IP)
Suction Temperature (F)

Outdoor
Temp (F)
65

75

85

95

105

115

125

30

35

40

45

50

55

Head Press (psig)

271.8

279.9

288.4

297.2

306.4

316.1

Capacity (Btuh/1000)

131.3

145.2

159.6

174.5

189.8

205.4

Unit Power (kW)

9.0

9.1

9.2

9.3

9.5

9.6

Head Press (psig)

309.7

318.0

326.8

335.9

345.4

355.2

Capacity (Btuh/1000)

123.8

137.0

150.6

164.7

179.1

193.7

Unit Power (kW)

9.8

9.9

10.1

10.2

10.4

10.5

Head Press (psig)

350.9

359.6

368.6

378.0

387.8

397.8

Capacity (Btuh/1000)

115.8

128.3

141.2

154.5

168.1

181.9

Unit Power (kW)

10.7

10.9

11.0

11.2

11.4

11.6

Head Press (psig)

395.5

404.6

414.0

423.6

433.6

443.9

Capacity (Btuh/1000)

107.3

119.2

131.5

144.0

156.9

169.9

Unit Power (kW)

11.8

12.0

12.1

12.3

12.5

12.6

Head Press (psig)

443.7

453.3

463.1

473.2

483.5

494.0

Capacity (Btuh/1000)

98.3

109.7

121.4

133.3

145.4

157.7

Unit Power (kW)

13.1

13.2

13.4

13.5

13.7

13.8

Head Press (psig)

495.8

505.8

516.0

526.5

537.2

547.9

Capacity (Btuh/1000)

89.0

99.8

110.9

122.2

133.6

145.1

Unit Power (kW)

14.4

14.6

14.7

14.9

15.0

15.1

Head Press (psig)

551.8

562.5

573.2

583.8

594.7

605.6

Capacity (Btuh/1000)

79.2

89.4

99.9

110.5

121.2

131.9

Unit Power (kW)

15.9

16.0

16.2

16.3

16.4

16.5

Note: Performance data calculated at 15F subcooling and 15F superheat and does not include capacity loss due to refrigerant lines.

Figure 10. TTA150E Capacity Curve

Capacity Curves - Condensing Unit Only


260
COMPRESSOR HIGH SUCTION LIMIT

250
240
230
220

200
INDOOR COIL FROST LIMIT

Gross Cooling Capacity (MBH)

210

190
180
170
160
150
140
130

65
75
85
95
105
115
125

120
110
100
90
80
70
25

30

35

40

45

50

55

60

65

70

75

Saturated Suction Temperature (F)

46

SS-PRC028-EN

Performance Data

Table 28. Gross Cooling Capacities (MBH) 15 Tons TTA180E Condensing Unit Only (IP)
Suction Temperature (F)

Outdoor
Temp (F)
65

75

85

95

105

115

125

30

35

40

45

50

55

Head Press (psig)

239.0

243.9

249.0

254.5

260.2

266.2

Capacity (Btuh/1000)

160.0

176.7

194.3

212.8

231.8

252.0

Unit Power (kW)

10.6

10.8

11.0

11.2

11.4

11.6

Head Press (psig)

274.6

279.8

285.2

290.9

296.9

303.2

Capacity (Btuh/1000)

150.8

166.9

183.9

201.7

220.2

239.4

Unit Power (kW)

11.4

11.6

11.8

12.0

12.2

12.5

Head Press (psig)

313.9

319.3

325.0

330.9

337.2

343.6

Capacity (Btuh/1000)

141.5

156.7

173.0

190.1

207.8

226.2

Unit Power (kW)

12.3

12.5

12.8

13.0

13.2

13.5

Head Press (psig)

356.8

362.5

368.4

374.6

381.0

387.7

Capacity (Btuh/1000)

131.8

146.3

161.7

178.0

194.9

212.4

Unit Power (kW)

13.5

13.7

13.9

14.1

14.4

14.6

Head Press (psig)

403.5

409.4

415.4

421.8

428.4

435.3

Capacity (Btuh/1000)

121.7

135.4

149.9

165.3

181.3

197.9

Unit Power (kW)

14.8

15.0

15.2

15.4

15.7

15.9

Head Press (psig)

454.2

460.3

466.5

472.9

479.7

486.7

Capacity (Btuh/1000)

111.2

124.1

137.6

152.0

167.0

182.5

Unit Power (kW)

16.3

16.5

16.7

16.9

17.1

17.3

Head Press (psig)

508.9

515.0

521.3

527.8

534.5

541.5

Capacity (Btuh/1000)

100.1

112.0

124.6

137.7

151.7

166.1

Unit Power (kW)

18.0

18.1

18.3

18.5

18.7

18.9

Note: Performance data calculated at 15F subcooling and 15F superheat and does not include capacity loss due to refrigerant lines.

Figure 11. TTA180E Capacity Curve

COMPRESSOR HIGH SUCTION LIMIT

320
310
300
290
280
270
260
250
240
230
220
210
200
190
180
170
160
150
140
130
120
110
100
90

INDOOR COIL FROST LIMIT

Gross Cooling Capacity (MBH)

Capacity Curves - Condensing Unit Only

65
75
85
95
105
115
125

25

30

35

40

45

50

55

60

65

70

75

Saturated Suction Temperature (F)

SS-PRC028-EN

47

Performance Data

Table 29. Gross Cooling Capacities (MBH) One Compressor - 15 Tons TTA180F Condensing Unit Only (IP)
Suction Temperature (F)

Outdoor
Temp (F)
65

75

85

95

105

115

125

30

35

40

45

50

55

Head Press (psig)

238.6

243.4

248.5

253.8

259.5

265.4

Capacity (Btuh/1000)

165.0

181.0

197.9

215.6

234.1

253.4

Unit Power (kW)

10.7

10.9

11.1

11.3

11.6

11.8

Head Press (psig)

274.3

279.3

284.6

290.2

296.1

302.2

Capacity (Btuh/1000)

156.6

172.0

188.2

205.3

223.0

241.5

Unit Power (kW)

11.5

11.7

11.9

12.1

12.4

12.6

Head Press (psig)

313.5

318.8

324.3

330.2

336.3

342.6

Capacity (Btuh/1000)

147.9

162.6

178.2

194.4

211.4

229.0

Unit Power (kW)

12.5

12.7

12.9

13.1

13.4

13.6

Head Press (psig)

356.4

361.9

367.7

373.7

380.0

386.6

Capacity (Btuh/1000)

138.8

152.8

167.6

183.1

199.2

215.9

Unit Power (kW)

13.6

13.8

14.1

14.3

14.5

14.7

Head Press (psig)

403.1

408.8

414.8

420.9

427.4

434.1

Capacity (Btuh/1000)

129.3

142.6

156.5

171.1

186.2

202.0

Unit Power (kW)

15.0

15.2

15.4

15.6

15.8

16.0

Head Press (psig)

453.8

459.7

465.7

472.0

478.6

485.4

Capacity (Btuh/1000)

119.3

131.8

144.8

158.4

172.6

187.3

Unit Power (kW)

16.5

16.7

16.9

17.1

17.3

17.5

Head Press (psig)

508.4

514.4

520.5

526.8

533.4

540.2

Capacity (Btuh/1000)

108.7

120.2

132.2

144.8

157.9

171.4

Unit Power (kW)

18.1

18.3

18.5

18.7

18.9

19.1

Note: Performance data calculated at 15F subcooling and 15F superheat and does not include capacity loss due to refrigerant lines.

Figure 12. TTA180F - One Compressor - Capacity Curve

Capacity Curves - Condensing Unit Only

COMPRESSOR HIGH SUCTION LIMIT

170
160
150

130
INDOOR COIL FROST LIMIT

Gross Cooling Capacity (MBH)

140

120
110
100
90
80

65
75
85
95
105
115
125

70
60
50
40
25

30

35

40

45

50

55

60

65

70

75

Saturated Suction Temperature (F)

48

SS-PRC028-EN

Performance Data

Table 30. Gross Cooling Capacities (MBH) Both Compressors - 15 Tons TTA180F Condensing Unit Only (IP)
Suction Temperature (F)

Outdoor
Temp (F)
65

75

85

95

105

115

125

30

35

40

45

50

55

Head Press (psig)

237.3

241.9

246.9

252.2

257.7

263.5

Capacity (Btuh/1000)

164.8

180.6

197.4

214.9

233.3

252.4

Unit Power (kW)

10.7

10.9

11.1

11.3

11.5

11.8

Head Press (psig)

272.7

277.7

282.9

288.3

294.1

300.1

Capacity (Btuh/1000)

156.3

171.6

187.7

204.5

222.1

240.3

Unit Power (kW)

11.5

11.7

11.9

12.1

12.3

12.6

Head Press (psig)

311.8

316.9

322.4

328.0

334.0

340.2

Capacity (Btuh/1000)

147.5

162.1

177.5

193.5

210.3

227.7

Unit Power (kW)

12.4

12.6

12.9

13.1

13.3

13.5

Head Press (psig)

354.5

359.9

365.5

371.4

377.5

383.9

Capacity (Btuh/1000)

138.3

152.2

166.8

182.0

197.8

214.3

Unit Power (kW)

13.6

13.8

14.0

14.2

14.4

14.7

Head Press (psig)

401.0

406.5

412.3

418.3

424.6

431.0

Capacity (Btuh/1000)

128.7

141.8

155.5

169.8

184.6

199.9

Unit Power (kW)

14.9

15.1

15.3

15.5

15.7

16.0

Head Press (psig)

451.4

457.1

463.0

468.9

475.2

481.7

Capacity (Btuh/1000)

118.6

130.8

143.6

156.7

170.3

184.4

Unit Power (kW)

16.4

16.6

16.8

17.0

17.2

17.4

Head Press (psig)

505.7

511.4

517.2

523.2

529.4

535.8

Capacity (Btuh/1000)

107.7

118.8

130.4

142.4

154.9

167.6

Unit Power (kW)

18.0

18.2

18.4

18.6

18.8

18.9

Note: Performance data calculated at 15F subcooling and 15F superheat and does not include capacity loss due to refrigerant lines.

Figure 13. TTA180F - Both Compressors - Capacity Curve

Capacity Curves - Condensing Unit Only

COMPRESSOR HIGH SUCTION LIMIT

95
90
85
80

INDOOR COIL FROST

Gross Cooling Capacity (kW)

75
70
65
60
55
50
45

18.3

40

23.9
29.4

35

35
40.6

30

46.1
51.7

25
-4

-2

10

12

14

16

18

20

22

24

Saturated Suction Temperature (C)

SS-PRC028-EN

49

Performance Data

Table 31. Gross Cooling Capacities (MBH) 20 Tons TTA240E Condensing Unit Only (IP)
Suction Temperature (F)

Outdoor
Temp (F)
65

75

85

95

105

115

125

30

35

40

45

50

55

Head Press (psig)

270.6

278.9

287.7

297.0

306.7

316.8

Capacity (Btuh/1000)

240.3

265.6

292.1

319.9

348.8

378.7

Unit Power (kW)

16.3

16.8

17.3

17.8

18.3

18.9

Head Press (psig)

308.8

317.5

326.6

336.2

346.1

356.5

Capacity (Btuh/1000)

228.7

252.7

277.8

304.1

331.4

359.6

Unit Power (kW)

17.6

18.0

18.6

19.1

19.7

20.2

Head Press (psig)

350.6

359.6

369.0

378.8

389.0

399.6

Capacity (Btuh/1000)

216.3

238.9

262.7

287.5

313.2

339.7

Unit Power (kW)

19.0

19.5

20.1

20.6

21.2

21.8

Head Press (psig)

396.0

405.2

414.9

424.9

435.4

446.2

Capacity (Btuh/1000)

203.1

224.4

246.7

270.0

294.1

319.0

Unit Power (kW)

20.7

21.2

21.8

22.3

22.9

23.5

Head Press (psig)

445.1

454.7

464.7

475.0

485.7

496.7

Capacity (Btuh/1000)

189.1

209.1

230.0

251.8

274.3

297.5

Unit Power (kW)

22.7

23.2

23.7

24.2

24.8

25.3

Head Press (psig)

498.3

508.2

518.4

528.9

539.7

550.8

Capacity (Btuh/1000)

174.3

192.9

212.4

232.6

253.5

274.9

Unit Power (kW)

24.8

25.3

25.8

26.3

26.9

27.4

Head Press (psig)

555.5

565.7

576.0

586.6

597.4

608.4

Capacity (Btuh/1000)

158.5

175.7

193.6

212.1

231.2

250.6

Unit Power (kW)

27.1

27.6

28.1

28.6

29.1

29.6

Note: Performance data calculated at 15F subcooling and 15F superheat and does not include capacity loss due to refrigerant lines.

Figure 14. TTA240E Capacity Curve


Capacity Curves - Condensing Unit Only
420
COMPRESSOR HIGH SUCTION LIMIT

400
380
360

320

INDOOR COIL FROST LIMIT

Gross Cooling Capacity (MBH)

340

300
280
260
240

65
75
85
95
105
115
125

220
200
180
160
140
25

30

35

40

45

50

55

60

Saturated Suction Temperature (F)

50

SS-PRC028-EN

Performance Data

Table 32. Gross Cooling Capacities (MBH) One Compressor - 20 Tons TTA240F Condensing Unit Only (IP)
Suction Temperature (F)

Outdoor
Temp (F)
65

75

85

95

105

115

125

30

35

40

45

50

55

Head Press (psig)

269.0

277.3

286.1

295.4

305.1

315.3

Capacity (Btuh/1000)

238.4

263.5

289.8

317.2

345.7

375.2

Unit Power (kW)

16.3

16.7

17.2

17.8

18.3

18.9

Head Press (psig)

306.5

315.0

324.0

333.5

343.5

353.8

Capacity (Btuh/1000)

226.5

250.2

275.1

301.0

327.9

355.5

Unit Power (kW)

17.5

18.0

18.5

19.0

19.6

20.2

Head Press (psig)

347.3

356.1

365.3

375.0

385.1

395.6

Capacity (Btuh/1000)

213.8

236.2

259.6

283.9

309.1

335.1

Unit Power (kW)

18.9

19.4

20.0

20.5

21.1

21.7

Head Press (psig)

391.6

400.6

410.0

419.8

430.0

440.6

Capacity (Btuh/1000)

200.2

221.3

243.2

266.0

289.5

313.7

Unit Power (kW)

20.6

21.1

21.6

22.2

22.7

23.3

Head Press (psig)

439.4

448.6

458.3

468.3

478.6

489.3

Capacity (Btuh/1000)

185.9

205.6

226.1

247.3

269.2

291.6

Unit Power (kW)

22.5

23.0

23.5

24.0

24.6

25.1

Head Press (psig)

491.0

500.4

510.1

520.2

530.6

541.4

Capacity (Btuh/1000)

170.8

189.1

208.0

227.7

247.9

268.5

Unit Power (kW)

24.6

25.0

25.5

26.0

26.6

27.1

Head Press (psig)

546.2

555.7

565.5

575.6

586.0

596.5

Capacity (Btuh/1000)

154.7

171.5

188.8

206.8

225.2

243.9

Unit Power (kW)

26.8

27.3

27.7

28.2

28.7

29.2

Note: Performance data calculated at 15F subcooling and 15F superheat and does not include capacity loss due to refrigerant lines.

Figure 15. TTA240F - One Compressor - Capacity Curves

Capacity Curves - Condensing Unit Only


220

COMPRESSOR HIGH SUCTION LIMIT

200

INDOOR COIL FROST LIMIT

Gross Cooling Capacity (MBH)

180

160

140

120

65
75
85
95
105
115
125

100

80

60
25

30

35

40

45

50

55

60

Saturated Suction Temperature (F)

SS-PRC028-EN

51

Performance Data

Table 33. Gross Cooling Capacities (MBH) Both Compressors - 20 Tons TTA240F Condensing Unit Only (IP)
Suction Temperature (F)

Outdoor
Temp (F)
65

75

85

95

105

115

125

30

35

40

45

50

55

Head Press (psig)

269.0

277.3

286.1

295.4

305.1

315.3

Capacity (Btuh/1000)

238.4

263.5

289.8

317.2

345.7

375.2

Unit Power (kW)

16.3

16.7

17.2

17.8

18.3

18.9

Head Press (psig)

306.5

315.0

324.0

333.5

343.5

353.8

Capacity (Btuh/1000)

226.5

250.2

275.1

301.0

327.9

355.5

Unit Power (kW)

17.5

18.0

18.5

19.0

19.6

20.2

Head Press (psig)

347.3

356.1

365.3

375.0

385.1

395.6

Capacity (Btuh/1000)

213.8

236.2

259.6

283.9

309.1

335.1

Unit Power (kW)

18.9

19.4

20.0

20.5

21.1

21.7

Head Press (psig)

391.6

400.6

410.0

419.8

430.0

440.6

Capacity (Btuh/1000)

200.2

221.3

243.2

266.0

289.5

313.7

Unit Power (kW)

20.6

21.1

21.6

22.2

22.7

23.3

Head Press (psig)

439.4

448.6

458.3

468.3

478.6

489.3

Capacity (Btuh/1000)

185.9

205.6

226.1

247.3

269.2

291.6

Unit Power (kW)

22.5

23.0

23.5

24.0

24.6

25.1

Head Press (psig)

491.0

500.4

510.1

520.2

530.6

541.4

Capacity (Btuh/1000)

170.8

189.1

208.0

227.7

247.9

268.5

Unit Power (kW)

24.6

25.0

25.5

26.0

26.6

27.1

Head Press (psig)

546.2

555.7

565.5

575.6

586.0

596.5

Capacity (Btuh/1000)

154.7

171.5

188.8

206.8

225.2

243.9

Unit Power (kW)

26.8

27.3

27.7

28.2

28.7

29.2

Note: Performance data calculated at 15F subcooling and 15F superheat and does not include capacity loss due to refrigerant lines.

Figure 16. TTA240F - Both Compressors - Capacity Curves

Capacity Curves - Condensing Unit Only


400
COMPRESSOR HIGH SUCTION LIMIT

380
360

320

INDOOR COIL FROST LIMIT

Gross Cooling Capacity (MBH)

340

300
280
260
240
220

65
75
85
95
105
115
125

200
180
160
140
25

30

35

40

45

50

55

60

Saturated Suction Temperature (F)

52

SS-PRC028-EN

Performance Data

Table 34. Evaporator Fan Performance TWE061 Air Handler


External Static Pressure (Inches of Water Gauge)
.10"
CFM

.20"

.30"

.40"

.50"

.60"

.70"

.80"

.90"

1.00"

RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP
3/4 HP Standard Motor & Drive

1600

738

0.33

790

0.38

840

0.44

888

0.50

936

0.56

0.62 1025

0.69

1070 0.76 1111 0.83

1700

719

0.33

771

0.38

821

0.44

869

0.50

914

0.56

959

0.62

1003 0.68 1047

980

0.75

1089 0.82 1129 0.90

1800

756

0.39

804

0.44

853

0.50

898

0.56

942

0.62

985

0.69

1028 0.75 1068

0.82

1109 0.89 1149 0.97

1900

792

0.45

838

0.51

884

0.57

928

0.63

971

0.69 1012

0.76

1052 0.83 1092

0.90

1131 0.97 1170 1.05

2000

829

0.52

873

0.58

917

0.64

959

0.71

1000 0.77 1040

0.84

1079 0.91 1117

0.98

1155 1.06 1192 1.14

2100

866

0.60

908

0.66

950

0.72

991

0.79

1030 0.86 1069

0.93

1106 1.00 1144

1.08

1179 1.15 1215 1.23

2200

903

0.68

944

0.74

983

0.81 1023

0.88

1061 0.95 1099

1.02

1134 1.10 1170

1.18

1206 1.26 1241 1.34

2300

940

0.78

979

0.84

1017 0.90 1055

0.97

1093 1.05 1129

1.13

1164 1.21 1198

1.28

1232 1.37 1266 1.45

2400

978

0.88 1015

0.94

1052 1.01 1089

1.08

1125 1.16 1160

1.24

1194 1.32 1227

1.40

1259 1.48 1292 1.57

1.5 HP High Static Kit


External Static Pressure
(Inches of Water Gauge)
1.10"

1.20"

1.30"

1.40"

CFM

RPM BHP RPM BHP RPM BHP RPM BHP

1600

1152 0.91 1191

0.99

1229 1.07 1264

1.14

1700

1170 0.98 1208

1.06

1246 1.14 1281

1.22

1800

1187 1.05 1226

1.13

1263 1.22 1300

1.30

1900

1207 1.13 1245

1.21

1281 1.30 1317

1.39

2000

1227 1.21 1265

1.30

1300 1.39 1335

1.48

2100

1250 1.31 1285

1.39

1319 1.48

2200

1274 1.42 1308

1.50

2300

1299 1.53

1.5 HP High Static Kit

2400

Notes:
1. Data includes pressure drop due to wet coil and 1" filter.
2. Fan motor heat (MBh) = 3.15 x BHP.
3. Tranes factory supplied motors, in commercial equipment, are definite purpose motors, specifically designed and tested to operate reliably and
continuously at all cataloged conditions. Using the full horsepower range of our fan motors as shown in our tabular data will not result in nuisance
tripping or premature motor failure. Our products warranty will not be affected.
4. For TWE061 Standard Drive use Table 41, p. 59, for High Static Drive use Table 42, p. 60.

SS-PRC028-EN

53

Performance Data

Table 35. Evaporator Fan Performance TWE090 Air Handler


External Static Pressure (Inches of Water Gauge)
.10"
CFM

.20"

.30"

.40"

.50"

.60"

.70"

.80"

.90"

1.00"

RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP
1.5 HP Standard Drive

2 HP High Static Drive Kit

2400

572

0.52

634

0.62

691

0.74

744

0.85

795

0.96

844

1.08

892

1.21

939

1.35

982

1.49

2550

592

0.59

652

0.70

707

0.82

759

0.95

809

1.06

856

1.18

902

1.31

947

1.45

990

1.59

2700

612

0.67

670

0.79

724

0.91

774

1.05

822

1.18

868

1.29

913

1.42

957

1.56

999

1.71

2850

575

0.68

633

0.73

689

0.89

741

1.01

790

1.15

837

1.29

882

1.42

925

1.55

967

1.68 1008 1.83

3000

599

0.76

654

0.82

709

0.99

760

1.13

807

1.26

853

1.41

896

1.56

939

1.69

980

1.82 1020 1.97

3150

623

0.85

675

0.93

729

1.11

778

1.25

825

1.39

869

1.54

911

1.70

953

1.85

992

1.98 1031 2.12

3300

647

0.95

697

1.09

749

1.22

797

1.38

842

1.52

886

1.67

927

1.83

967

2.00

1007 2.15 1045 2.30

3450

673

1.08

724

1.26

770

1.32

816

1.52

861

1.67

903

1.82

943

1.98

983

2.16

1020 2.33 1058 2.48

3600

698

1.21

746

1.43

790

1.43

836

1.67

880

1.83

922

1.98

961

2.14

999

2.32

1037 2.51 1073 2.68

3 HP Ultra High Static Drive Kit


External Static Pressure (Inches of Water Gauge)
1.10"

1.20"

1.30"

1.40"

1.50"

1.60"

1.70"

1.80"

1.90

2.00

CFM

RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP

2400

1023 1.62 1062

1.75

1101 1.89 1137

2.03

1172 2.16 1207

2.30

1241 2.44 1273

2.58

1303 2.71 1334 2.85

2550

1032 1.74 1071

1.88

1109 2.03 1145

2.17

1181 2.32 1215

2.46

1248 2.61 1281

2.75

1311 2.89 1341 3.04

2700

1040 1.86 1079

2.01

1117 2.17 1154

2.32

1189 2.47 1223

2.62

1255 2.77 1288

2.93

2850

1048 1.99 1087

2.14

1126 2.31 1161

2.47

1198 2.63 1232

2.79

1264 2.95

3000

1058 2.12 1096

2.29

1135 2.46 1171

2.63

1206 2.80 1239

3150

1069 2.27 1105

2.43

1142 2.60 1179

2.79

1214 2.96

3300

1082 2.45 1118

2.61

1154 2.78 1187

2.95

1164 2.96

2 HP High Static Drive Kit

3450

1094 2.63 1130

2.79

3600

1107 2.84 1144

3.00

3 HP Ultra High Static Drive Kit

2.96

Notes:
1. Data includes pressure drop due to wet coil and 1" filter.
2. Fan motor heat (MBh) = 3.15 x BHP.
3. Tranes factory supplied motors, in commercial equipment, are definite purpose motors, specifically designed and tested to operate reliably and
continuously at all cataloged conditions. Using the full horsepower range of our fan motors as shown in our tabular data will not result in nuisance
tripping or premature motor failure. Our products warranty will not be affected.
4. For TWE090 Standard Drive use Table 41, p. 59, for High Static Drive use Table 42, p. 60, for Ultra High Static Drive use Table 43, p. 61.

54

SS-PRC028-EN

Performance Data

Table 36. Evaporator Fan Performance TWE120 Air Handler


External Static Pressure (Inches of Water Gauge)
.10"
CFM

.20"

.30"

.40"

RPM BHP RPM BHP RPM BHP RPM BHP

.50"

.60"

.70"

.80"

.90"

1.00"

RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP
2 HP Standard Drive

3200

588

0.87

625

0.95

658

1.03

691

1.13

722

1.22

753

1.32

783

1.40

812

1.48

3400

611

1.01

646

1.09

679

1.18

711

1.27

742

1.38

771

1.48

799

1.57

828

1.67

3600

598

1.04

634

1.16

668

1.26

700

1.34

731

1.44

761

1.54

789

1.65

817

1.76

844

1.86

3800

588

1.17

624

1.24

658

1.29

691

1.43

722

1.53

752

1.62

781

1.72

809

1.83

835

1.95

862

2.07

4000

616

1.34

651

1.47

682

1.45

714

1.63

745

1.73

774

1.83

801

1.93

829

2.04

855

2.16

880

2.28

4200

643

1.52

677

1.70

706

1.65

738

1.81

767

1.95

795

2.05

823

2.15

849

2.26

874

2.38

899

2.50

4400

670

1.74

703

1.94

731

1.90

761

2.00

790

2.19

818

2.29

844

2.40

870

2.51

895

2.63

919

2.75

4600

698

1.97

729

2.19

756

2.20

785

2.21

814

2.44

840

2.56

866

2.67

891

2.78

915

2.90

4800

726

2.23

755

2.46

785

2.53

809

2.47

837

2.65

863

2.85

889

2.96

3 HP Hi Static Drive Kit


External Static Pressure (Inches of Water Gauge)
1.10"
CFM

1.20"

1.30"

1.40"

RPM BHP RPM BHP RPM BHP RPM BHP

1.50"

1.60"

1.70"

1.80"

1.90

2.00

RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP

3 HP Hi Static Drive Kit

3 HP High Static Drive w/ Field Supplied Sheave & Belt

3200

839

1.58

866

1.67

893

1.77

920

1.88

946

1.99

971

2.10

2.21 1019 2.32

1044

2.43 1066 2.54

3400

854

1.75

881

1.85

906

1.95

931

2.05

957

2.16

982

2.28

1007 2.40 1030 2.51

996

1054

2.63 1076 2.74

3600

871

1.96

896

2.05

922

2.15

946

2.25

970

2.36

993

2.47

1018 2.59 1042 2.72

1065

2.84 1087 2.96

3800

887

2.18

912

2.28

937

2.38

961

2.48

985

2.58 1008

2.70

1030 2.81 1053 2.93

4000

905

2.40

930

2.52

953

2.62

977

2.73

1000 2.83 1022

2.94

4200

923

2.63

947

2.76

970

2.89

993

3.00

4400

942

2.88

4600

4800

External Static Pressure (Inches of Water Gauge)


2.10"
CFM

2.20"

RPM BHP RPM BHP


3 HP High Static Drive
w/ Field Supplied Sheave & Belt

3200

1088 2.64 1109

2.75

3400

1098 2.86 1120

2.97

3600

3800

4000

4200

4400

4600

4800

Notes:
1. Data includes pressure drop due to wet coil and 1" filter.
2. Fan motor heat (MBh) = 3.15 x BHP.
3. Tranes factory supplied motors, in commercial equipment, are definite purpose motors, specifically designed and tested to operate reliably and
continuously at all cataloged conditions. Using the full horsepower range of our fan motors as shown in our tabular data will not result in nuisance
tripping or premature motor failure. Our products warranty will not be affected.
4. For TWE120 Standard Drive use Table 41, p. 59, for High Static Drives use Table 42, p. 60.

SS-PRC028-EN

55

Performance Data

Table 37. Evaporator Fan Performance TWE150 Air Handler


External Static Pressure (Inches of Water Gauge)
.10"
CFM

.20"

.30"

.40"

.50"

.60"

.70"

.80"

.90"

1.00"

RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP
2 HP Standard Drive

4000

614

0.85

658

0.98

698

1.12

728

1.22

756

1.32

786

1.43

817

1.56

4200

581

0.80

627

0.93

669

1.05

710

1.21

744

1.34

772

1.44

799

1.55

827

1.66

4400

595

0.88

640

1.02

682

1.15

722

1.29

758

1.45

789

1.58

814

1.68

840

1.79

4600

563

0.82

609

0.96

653

1.11

695

1.25

732

1.38

771

1.55

804

1.71

831

1.83

856

1.94

4800

579

0.90

624

1.05

667

1.20

707

1.35

745

1.50

783

1.66

817

1.83

847

1.98

872

2.10

5000

595

0.99

639

1.15

681

1.31

721

1.47

759

1.62

794

1.77

828

1.94

861

2.12

888

2.27

5200

568

0.95

612

1.09

655

1.25

695

1.42

735

1.58

771

1.74

806

1.90

840

2.06

873

2.25

903

2.43

5400

587

1.05

628

1.20

670

1.36

710

1.53

748

1.71

784

1.88

819

2.04

852

2.20

885

2.38

915

2.58

5600

605

1.16

645

1.31

686

1.48

724

1.66

762

1.83

798

2.01

832

2.19

864

2.35

896

2.52

928

2.73

5800

624

1.28

662

1.43

702

1.60

740

1.79

777

1.97

812

2.15

845

2.34

877

2.51

908

2.68

938

2.87

6000

643

1.40

679

1.56

719

1.74

755

1.92

791

2.12

826

2.30

858

2.49

891

2.68

920

2.86

950

3.03

2 HP Hi Static Drive w/ Field Supplied Sheave & Belt


External Static Pressure (Inches of Water Gauge)
1.10"
CFM

1.20"

1.30"

1.40"

1.50"

1.60"

1.70"

1.80"

1.90

2.00

RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP
2 HP Hi Static Drive w/ Field Supplied Sheave & Belt

3 HP High Static Drive Kit

4000

849

1.70

882

1.85

915

2.02

947

2.19

976

2.36 1002

2.52

1028 2.69 1053

2.86

1078 3.03 1101 3.20

4200

858

1.80

888

1.95

919

2.11

950

2.28

980

2.45 1010

2.64

1036 2.81 1061

2.98

1085 3.15 1109 3.33

4400

867

1.92

896

2.06

925

2.21

955

2.38

985

2.55 1013

2.73

1044 2.93 1070

3.11

1094 3.30 1117 3.47

4600

880

2.05

906

2.19

934

2.33

961

2.49

989

2.66 1018

2.84

1045 3.02 1074

3.22

1101 3.43 1125 3.61

4800

896

2.22

918

2.33

944

2.47

970

2.63

996

2.79 1023

2.96

1051 3.15 1078

3.34

1105 3.55 1131 3.74

5000

911

2.39

934

2.51

956

2.64

980

2.78

1005 2.93 1031

3.11

1057 3.28 1083

3.48

1109 3.67 1135 3.87

5200

927

2.57

950

2.71

972

2.83

993

2.95

1016 3.11 1040

3.27

1064 3.43 1090

3.62

1115 3.82 1139 4.01

5400

943

2.76

966

2.90

989

3.04 1008

3.17

1029 3.30 1051

3.45

1075 3.62 1098

3.79

1122 3.98 1146 4.17

5600

956

2.92

982

3.11

1004 3.25 1025

3.39

1045 3.52 1065

3.66

1085 3.81 1108

3.98

1130 4.16 1153 4.35

5800

969

3.09

996

3.29

1020 3.47 1041

3.62

1062 3.77 1081

3.91

1099 4.04 1120

4.20

1141 4.37 1162 4.55

6000

980

3.25 1008

3.46

1034 3.67 1057

3.86

1077 4.01 1097

4.16

1115 4.30 1134

4.45

1153 4.60 1174 4.78

5 HP Ultra High Static Drive


External Static Pressure (Inches of Water Gauge)
2.10"

2.20"

2.30

2.40

CFM

RPM BHP RPM BHP RPM BHP RPM BHP

4000

1126 3.38 1148

3.54

1170 3.73 1191

3.89

4200

1132 3.51 1155

3.69

1179 3.88 1200

4.06

4400

1141 3.66 1163

3.84

1186 4.03 1208

4.23

4600

1150 3.81 1172

4.00

1193 4.18 1215

4.37

4800

1157 3.96 1179

4.15

1202 4.36

5000

1161 4.09 1186

4.30

1210 4.52

5200

1164 4.21 1189

4.44

1214 4.66

5400

1170 4.38 1193

4.58

1218 4.81

5600

1176 4.55 1198

4.74

1222 4.97

5800

1184 4.74 1206

4.94

6000

1194 4.96

5 HP Ultra High Static Drive

Notes:
1. Data includes pressure drop due to wet coil and 1" filter.
2. Fan motor heat (MBh) = 3.15 x BHP.
3. Tranes factory supplied motors, in commercial equipment, are definite purpose motors, specifically designed and tested to operate reliably and
continuously at all cataloged conditions. Using the full horsepower range of our fan motors as shown in our tabular data will not result in nuisance
tripping or premature motor failure. Our products warranty will not be affected.
4. For TWE150 Standard Drive use Table 41, p. 59, for High Static Drive use Table 42, p. 60, for Ultra High Static Drive (3 HP) use Table 43, p. 61.

56

SS-PRC028-EN

Performance Data

Table 38. Evaporator Fan Performance TWE180 Air Handler


External Static Pressure (Inches of Water Gauge)
.10"
CFM

.20"

.30"

.40"

.50"

.60"

.70"

.80"

.90"

1.00"

RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP
3 HP Low Static Drive w/ Field Supplied Sheave & Belt

3 HP Standard Drive

4500

468

0.68

517

0.80

563

0.94

606

1.06

646

1.19

686

1.34

725

1.50

760

1.65

793

1.80

825

1.94

4800

492

0.80

539

0.94

583

1.08

624

1.21

663

1.34

701

1.49

738

1.66

774

1.82

807

1.98

839

2.14

5100

517

0.95

562

1.08

604

1.24

644

1.38

681

1.52

718

1.67

753

1.83

788

2.00

821

2.18

853

2.35

5400

542

1.11

585

1.25

625

1.41

663

1.57

700

1.71

735

1.86

769

2.02

802

2.20

835

2.38

866

2.57

5700

567

1.29

609

1.43

647

1.60

684

1.78

719

1.93

753

2.08

786

2.24

818

2.41

849

2.60

881

2.80

6000

593

1.48

632

1.64

669

1.80

705

1.99

739

2.16

773

2.32

804

2.48

835

2.66

865

2.84

895

3.04

6300

619

1.70

656

1.86

692

2.03

726

2.22

760

2.42

792

2.59

823

2.75

853

2.93

882

3.12

910

3.31

6600

644

1.94

681

2.11

715

2.28

748

2.48

781

2.69

811

2.87

841

3.04

871

3.22

899

3.40

927

3.60

6900

670

2.20

705

2.37

739

2.55

771

2.75

802

2.97

832

3.18

861

3.36

890

3.54

917

3.72

944

3.92

7200

696

2.49

730

2.66

763

2.85

794

3.05

824

3.27

853

3.49

881

3.70

909

3.89

936

4.08

963

4.28

5 HP High Static Drive Kit


External Static Pressure (Inches of Water Gauge)
1.10"
CFM

1.20"

1.30"

1.40"

1.50"

1.60"

1.70"

1.80"

1.90

2.00

RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP
5 HP Motor & Sheaves

5 HP Ultra High Static w/ Field Supplied Sheave & Belt

4500

856

2.09

885

2.24

912

2.38

939

2.53

965

2.67

2.81

1015 2.96 1039

3.10

1062 3.24 1085 3.39

4800

869

2.30

897

2.46

926

2.62

953

2.77

979

2.93 1004

3.08

1029 3.24 1051

3.38

1075 3.54 1097 3.69

5100

883

2.52

911

2.69

940

2.86

965

3.02

992

3.19 1017

3.36

1042 3.52 1065

3.68

1088 3.84 1111 4.02

5400

897

2.75

925

2.93

953

3.11

980

3.29

1005 3.47 1031

3.65

1055 3.82 1078

3.99

1102 4.17 1123 4.34

5700

910

2.99

940

3.19

966

3.38

993

3.57

1019 3.75 1044

3.94

1068 4.13 1092

4.32

1114 4.50 1137 4.69

6000

924

3.25

953

3.45

980

3.65 1008

3.86

1033 4.06 1057

4.26

1081 4.45 1105

4.66

1129 4.86 1150 5.05

6300

939

3.52

967

3.73

995

3.95 1022

4.17

1046 4.37 1071

4.59

1095 4.79 1119

5.01

6600

954

3.81

981

4.02

1009 4.25 1035

4.48

1061 4.71 1085

4.93

998

1074 5.04

6900

971

4.13

7200

988

4.48 1014

4.35

1022 4.57 1049

4.81

4.70

1039 4.93 1063

5.15

990

External Static Pressure (Inches of Water Gauge)


2.10"
CFM

2.20"

2.30

2.40

RPM BHP RPM BHP RPM BHP RPM BHP


5 HP Ultra High Static
w/ Field Supplied Sheave & Belt

4500

1106 3.52 1128

3.66

1149 3.80 1171

3.95

4800

1120 3.84 1141

3.99

1162 4.14 1183

4.30

5100

1132 4.17 1154

4.33

1175 4.49 1196

4.66

5400

1146 4.52 1167

4.69

1188 4.86 1209

5.04

5700

1159 4.87 1180

5.06

6000

6300

6600

6900

7200

Notes:
1. Data includes pressure drop due to wet coil and 1" filter.
2. Fan motor heat (MBh) = 3.15 x BHP.
3. Tranes factory supplied motors, in commercial equipment, are definite purpose motors, specifically designed and tested to operate reliably and
continuously at all cataloged conditions. Using the full horsepower range of our fan motors as shown in our tabular data will not result in nuisance
tripping or premature motor failure. Our products warranty will not be affected.
4. For TWE180 Low Static Drive use Table 40, p. 59, for Standard Drive use Table 41, p. 59, for High Static Drive use Table 42, p. 60.

SS-PRC028-EN

57

Performance Data

Table 39. Evaporator Fan Performance TWE240 Air Handler


External Static Pressure (Inches of Water Gauge)
.10"
CFM

.20"

.30"

.40"

.50"

.60"

.70"

RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP

.80"

RPM BHP RPM BHP

3 HP Low Static Drive Kit

.90"

1.00"

RPM BHP RPM BHP

5 HP Standard Drive

6400

652

1.55

693

1.70

732

1.86

769

2.02

802

2.17

833

2.33

867

2.53

901

2.75

6800

677

1.79

717

1.96

754

2.12

791

2.29

824

2.46

855

2.62

885

2.79

916

3.00

7200

661

1.87

703

2.05

742

2.24

778

2.42

812

2.59

846

2.77

878

2.95

906

3.11

934

3.29

7600

647

1.98

688

2.15

729

2.34

766

2.55

802

2.74

835

2.92

868

3.10

900

3.29

929

3.48

956

3.66

8000

677

2.29

716

2.47

755

2.67

791

2.88

826

3.09

858

3.28

889

3.47

921

3.67

951

3.87

979

4.06

8400

707

2.63

744

2.82

781

3.02

817

3.24

851

3.46

883

3.68

913

3.87

942

4.07

972

4.28 1000

4.49

8800

737

3.01

773

3.21

808

3.41

843

3.63

876

3.87

907

4.10

937

4.31

965

4.52

994

4.73 1022

4.95

9200

767

3.41

802

3.63

836

3.84

869

4.06

901

4.30

932

4.55

961

4.79

989

5.00

1016 5.21 1044

5.44

9600

797

3.86

831

4.08

863

4.30

896

4.53

927

4.78

957

5.03

986

5.29 1013

5.52

1040 5.75 1065

5.97

7.5 HP Ultra Hi Static Drive Kit

5 HP Hi Static Drive w/ Field


Supplied Sheaves

External Static Pressure (Inches of Water Gauge)


1.10"
CFM

1.20"

1.30"

1.40"

1.50"

1.60"

RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP RPM BHP
5 HP Standard Drive

6400

934

2.95

965

3.16

6800

948

3.22

979

7200

964

3.51

994

7600

982

996

1.70"

1.80"

RPM BHP RPM BHP

1.90

2.00

RPM BHP RPM BHP

5 HP Hi Static Drive w/ Field Supplied Sheaves

3.37 1028

3.58

1059 3.81 1091

4.03

1120 4.25 1148

4.46

1177 4.69 1204

4.90

3.45

1008 3.66 1039

3.89

1069 4.12 1099

4.35

1128 4.58 1156

4.81

1185 5.05 1212

5.28

3.75

1024 3.99 1052

4.22

1079 4.45 1108

4.69

1136 4.93 1166

5.19

1193 5.43 1219

5.67

3.85 1011

4.07

1039 4.31 1066

4.56

1095 4.82 1121

5.06

1148 5.31 1174

5.56

1202 5.82 1228

6.07

8000

1004 4.25 1029

4.45

1055 4.67 1082

4.92

1109 5.19 1136

5.46

1161 5.71 1186

5.97

1213 6.24 1236

6.48

8400

1027 4.70 1051

4.90

1075 5.10 1100

5.33

1125 5.58 1151

5.85

1177 6.14 1202

6.42

1225 6.68 1250

6.96

8800

1049 5.17 1074

5.39

1097 5.59 1120

5.81

1144 6.03 1168

6.30

1192 6.57 1216

6.85

1241 7.16 1264

7.44

9200

1071 5.68 1096

5.90

1120 6.13 1143

6.34

1164 6.56 1186

6.79

1209 7.05 1233

7.35

9600

1092 6.21 1117

6.45

1142 6.69 1166

6.93

1187 7.15 1208

7.38

7.5 HP Ultra High Static Drive Kit

7.5 HP Ultra High Motor w/ Field Supplied Fan Sheave & Belt

External Static Pressure (Inches of Water Gauge)


2.10"
CFM

2.20"

2.30

2.40

RPM BHP RPM BHP RPM BHP RPM BHP


7.5 HP Ultra High Motor w/ Field Supplied
Fan Sheave & Belt

6400

1230 5.11 1257

5.33

1282 5.54 1308

5.77

6800

1239 5.52 1265

5.75

1290 5.98 1315

6.20

7200

1246 5.92 1272

6.17

1298 6.41 1323

6.66

7600

1255 6.35 1282

6.61

1306 6.86

8000

1262 6.76 1289

7.04

1313 7.31

8400

1273 7.22

8800

9200

9600

Notes:
1. Data includes pressure drop due to wet coil and 1" filter.
2. Fan motor heat (MBh) = 3.15 x BHP.
3. Tranes factory supplied motors, in commercial equipment, are definite purpose motors, specifically designed and tested to operate reliably and
continuously at all cataloged conditions. Using the full horsepower range of our fan motors as shown in our tabular data will not result in nuisance
tripping or premature motor failure. Our products warranty will not be affected.
4. For TWE240 Low Static Drive use Table 40, p. 59, for Standard Drive use Table 41, p. 59, for High Static Drives (5 HP and 7 HP) use Table 42, p. 60.

58

SS-PRC028-EN

Performance Data

Table 40. Low Static Fan Drives


15 Ton TWE180 Low Static Drive
with Field Supplied Sheave and Belt(a)

20 Ton TWE240
Low Static Drive Kit

Motor Sheave Turns Open

Nominal RPM

Motor Sheave Turns Open

Nominal RPM

649

855

613

812

557

769

500

726

444

683

469

640

(a)TWE180 3HP Lo-Static w/ field installed belt and sheaves


Field Supplied Components Required:
Motor Sheave: Variable Pitch (2.4 - 3.4 Inch Pitch Diameter), 0.875 Inch Bore, Single Groove, Browning 1VL40
Blower Sheave: Fixed Pitch (9.5 Inch Pitch Diameter), 1.4375 Inch Bore, Single Groove, Browning AX59

Table 41. Standard Fan Drives


5 Ton TWE061 Standard Drive

7.5 Ton TWE090 Standard Drive

Motor Sheave Turns Open

Nominal RPM

Motor Sheave Turns Open

Nominal RPM

1071

847

1000

791

928

734

857

678

785

621

714

565

10 Ton TWE120 Standard Drive

12.5 Ton TWE150 Standard Drive

Motor Sheave Turns Open

Nominal RPM

Motor Sheave Turns Open

Nominal RPM

818

768

773

725

727

683

682

640

636

598

591

555

15 Ton TWE180 Standard Drive

20 Ton TWE240 Standard Drive (5 HP)

Motor Sheave Turns Open

Nominal RPM

Motor Sheave Turns Open

Nominal RPM

845

966

812

932

728

899

745

865

711

831

678

798

644

764

SS-PRC028-EN

59

Performance Data

Table 42. High Static Fan Drives


5 Ton TWE061 High Static Drive

7 Ton TWE090 High Static Drive

Motor Sheave Turns Open

Nominal RPM

Motor Sheave Turns Open

Nominal RPM

1346

1094

1279

1039

1212

984

1144

930

1077

875

1010

820

10 Ton TWE120
High Static Drive

10 Ton TWE120 High Static Drive


with Field Supplied Sheave and Belt(a)

Motor Sheave Turns Open

Nominal RPM

Motor Sheave Turns Open

Nominal RPM

972

1129

923

1073

875

1016

826

960

778

903

729

847

12 Ton TWE150
High Static Drive (3 HP)

12 Ton TWE150 High Static Drive


with Field Supplied Sheave and Belt(b)

Motor Sheave Turns Open

Nominal RPM

Motor Sheave Turns Open

Nominal RPM

1094

913

1039

862

991

806

942

749

893

693

820

659

15 Ton TWE180
High Static Drive

15 Ton TWE180 High Static Drive


with Field Supplied Sheave(c)

Motor Sheave Turns Open

Nominal RPM

Motor Sheave Turns Open

1024

Nominal RPM
1217

989

1175

953

1118

918

1062

882

1006

847

964

811

964

20 Ton TWE240 High Static Drive


with Field Supplied Sheave & Belt (5 HP)(d)
Motor Sheave Turns Open

Nominal RPM

1091

1053

1015

978

940

902

864

See next page for notes on required field supplied components

60

SS-PRC028-EN

Performance Data

(a) TWE120 3HP Hi-Static w/ field installed belt and sheaves


Field Supplied Components Required:
Motor Sheave: Variable Pitch (2.8 - 3.8 Inch Pitch Diameter), 0.875 Inch Bore, Single Groove, Browning 1VP44
Blower Sheave: Fixed Pitch (6.0 Inch Pitch Diameter), 1.0 Inch Bore, Single Groove, Browning AK64
Belt: Browning A50
(b)TWE150 2HP Hi-Static w/ field installed belt and sheaves
Field Supplied Components Required:
Motor Sheave: Variable Pitch (2.4 - 3.4 Inch Pitch Diameter), 0.875 Inch Bore, Single Groove, Browning 1VL40
Blower Sheave: Fixed Pitch (6.7 Inch Pitch Diameter), 1.4375 Inch Bore, Single Groove, Browning AK71
Belt: Browning A55
(c)TWE180 5HP Hi-Static w/ field installed belt and sheaves
Field Supplied Components Required:
Motor Sheave: Variable Pitch (3.4 - 4.4 Inch Pitch Diameter), 1.125 Inch Bore, Single Groove, Browning 1VP50
Blower Sheave: Fixed Pitch (6.6 Inch Pitch Diameter), 1.4375 Inch Bore, Single Groove, Browning BK72
Belt: Browning BX58
(d) TWE240 5HP Hi-Static w/ field installed belt and sheaves
Field Supplied Components Required:
Motor Sheave: Variable Pitch (3.4 - 4.4 Inch Pitch Diameter), 1.125 Inch Bore, Single Groove, Browning 1VP50
Blower Sheave: Fixed Pitch(7.4 Inch Pitch Diameter), 1.4375 Inch Bore, Single Groove, Browning BK115
Belt: Browning BX57

Table 43. Ultra High Static Fan Drives


7 Ton TWE090
Ultra High Static Drive Kit

12 Ton TWE150
Ultra High Static Drive (5 HP)

Motor Sheave Turns Open

Nominal RPM

Motor Sheave Turns Open

Nominal RPM

1346

1217

1241

1175

1136

1133

1030

1091

925

1048

820

1006

964

20 Ton TWE240 Ultra High Static Drive


(7.5 HP Motor)

20 Ton TWE240 Ultra High Static Drive


with Field Supplied Sheave (7.5 HP Motor)(a)

Motor Sheave Turns Open

Nominal RPM

Motor Sheave Turns Open

Nominal RPM

1294

1315

1243

1281

1191

1243

1140

1205

1089

1168

1037

1100

986

1111

(a)TWE240 7.5HP Ultra Hi-Static w/ field installed belt and sheaves


Field Supplied Components Required:
Motor Sheave: Variable Pitch (2.8 - 3.8 Inch Pitch Diameter), 1.125 Inch Bore, Single Groove, Browning 1VP44
Blower Sheave: Fixed Pitch (10.4 Inch Pitch Diameter), 1.4375 Inch Bore, Single Groove, Browning BK110
Belt: Browning BX62

SS-PRC028-EN

61

Performance Data

Table 44. Discharge Plenum and Grille Assembly Throw Distance (ft) Air Handler
Louver Angle Deflection Position
Tons

10

12

15

20

Model No.

TWE061D
TWE061E

TWE090D
TWE090E

TWE120D
TWE120E

TWE150E

TWE180E

TWE240E

CFM

Straight

20

40

55

1600

42

31

26

20

1800

46

37

29

22

2000

48

43

33

24

2200

51

50

36

25

2400

54

57

39

29

2400

52

43

35

29

2700

55

48

38

31

3000

58

53

42

32

3300

62

57

46

35

3600

66

60

50

37

3200

56

46

38

30

3600

62

51

42

33

4000

66

57

47

35

4400

71

62

52

38

4800

76

67

56

42

4900

47

38

32

25

5400

52

44

37

29

6000

57

49

41

32

6600

61

53

43

34

7200

65

57

46

35

4900

47

38

32

25

5400

52

44

37

29

6000

57

49

41

32

6600

61

53

43

34

7200

65

57

46

35

6400

56

46

38

30

7200

62

51

42

33

8000

66

57

47

35

8800

71

62

52

38

9600

76

67

56

42

Notes:
1. Throw distance values are based on a terminal velocity of 75 FPM.
2. Throw distance values at other terminal velocities may be established by multiplying throw
distances in the table above by throw factor.

62

Terminal
Velocity

Throw
Factor

50 FPM

x 1.50

100 FPM

x .75

150 FPM

x .50

SS-PRC028-EN

Performance Data

Table 45. Electric Heat Discharge Plenum and Grille Airflow (CFM)
Airflow (CFM)

Electric Heater
Model No.

Minimum

Maximum

BAYHTRL117A

2000

2400

BAYHTRL315A

2000

2400

BAYHTRL415A

2000

2400

BAYHTRL117A

3000

3600

BAYHTRL123A

3375

3600

BAYHTRL315A

2625

3600

BAYHTRL325A

3000

3600

BAYHTRL415A

2625

3600

BAYHTRL425A

2625

3600

BAYHTRL117A

3500

4800

BAYHTRL123A

4000

4800

BAYHTRL315A

4000

4800

BAYHTRL325A

3500

4800

BAYHTRL415A

3500

4800

BAYHTRL425A

3500

4800

12

TWE150E3
TWE150E3(a)

BAYHTRM330A

5250

6000

BAYHTRM430A

5250

6000

15

TWE180E3
TWE180E3(a)

BAYHTRM330A

5250

7200

BAYHTRM430A

5250

7200

20

TWE240E3
TWE240E4

BAYHTRM330A

7000

9600

BAYHTRM430A

7000

9600

Tons

Unit Model No.

TWE061D1, E1
TWE061D3, E3
TWE061D4, E4

7 1/2

10

TWE090D1, E1
TWE090D3, E3(a)
TWE090D3, E3(a)

TWE120D1, E1
TWE120D3, E3(a)
TWE120D3, E3(a)

(a) When wired for 460 volt, used with BAYHTRL4*** only.

Table 46. Static Pressure Drop Through Accessories (inches of water column)(a) Air Handlers

Tons
5

10

12

15

20

Unit Model No.


TWE061D
TWE061E
TWE090D
TWE090E
TWE120D
TWE120E

TWE150E

TWE180E

TWE240E

CFM

Return
Grille

Discharge
Plenum and
Grille(b)

Electric Heaters (kW)

Hydronic Coils

5-10

15-20

25-30

35-50

Steam

Hot Water

1600

0.12

0.21

0.08

0.08

0.14

.44

.31

2000

0.18

0.33

0.13

0.13

0.19

.62

.44

2400

0.28

0.47

0.19

0.19

0.37

.80

.59

2400

0.08

0.27

0.03

0.06

0.08

0.12

.38

.23

3000

0.13

0.4

0.06

0.12

0.17

0.23

.50

.33

3600

0.18

0.58

0.08

0.16

0.24

0.32

.66

.44

3200

0.07

0.43

0.06

0.13

0.19

0.26

.42

.40

4000

0.11

0.66

0.10

0.20

0.30

0.40

.59

.56

4800

0.15

0.95

0.14

0.28

0.42

0.57

.76

.75

4000

0.06

0.16

0.02

0.02

0.04

0.08

0.28

0.24

5000

0.10

0.25

0.03

0.03

0.08

0.12

0.44

0.38

6000

0.14

0.36

0.04

0.05

0.12

0.17

0.64

0.54

4800

0.09

0.23

0.03

0.03

0.06

0.08

.46

.38

6000

0.15

0.34

0.06

0.06

0.12

0.17

.64

.54

7200

0.2

0.49

0.08

0.08

0.16

0.24

.82

.72

6400

0.11

0.43

0.06

0.06

0.13

0.19

.50

.41

8000

0.17

0.66

0.10

0.10

0.20

0.30

.70

.58

9600

0.23

0.95

0.14

0.14

0.28

0.42

.89

.78

(a) Return air filter ESP included in Fan Performance Table data.
(b) At louver opening angle of 42 degrees. For ESP at other angle openings, see accessory installation guide.

SS-PRC028-EN

63

Performance Data

Table 47. Auxiliary Electric Heat Capacity - Air Handler


Stage 1
No. of
Stages

Total

Unit Model No.

5.00

5.00

17,065

5.00

17,065

TWE061D3, D4, DW

9.96

9.96

33,993

9.96

33,993

TWE061E3, E4

14.96

14.96

51,058

14.96

51,058

24.92

14.96

51,058

9.96

33,993

24.92

85,051

5.00

5.00

17,065

5.00

17,065

kW Input

BTUH
Output

Stage 2

Total
kW

kW Input

BTUH
Output

kW Input

BTUH
Output

TWE090(a),120D3(a),DW

9.96

9.96

33,993

9.96

33,993

TWE090E3(a)

14.96

14.96

51,058

14.96

51,058

TWE120E3(a), EW

24.92

14.96

51,058

9.96

33,993

24.92

85,051

TWE061,090,120D1

5.76

5.76

19,659

5.76

19,659

TWE060E1

11.52

11.52

39,318

11.52

39,318

TWE090E1

17.28

17.28

58,977

17.28

58,977

TWE120E1

23.04

11.52

39,318

11.52

39,318

23.04

78,636

TWE090,120D1, E1

28.8

17.28

58,977

11.52

39,318

28.8

98,295

TWE090(a),120D3(a), DW

34.88

19.92

67,987

14.96

51,058

34.88

119,045

TWE120E3(a), EW

TWE150E, 180E, 240E

10.00

10.00

34,130

10.00

34,130

10.00

10.00

34,130

10.00

34,130

19.92

19.92

67,987

19.92

67,987

29.92

19.92

67,987

10.00

34,130

29.92

102,117

49.84

29.92

102,117

19.92

67,987

49.84

170,104

Note: Heaters are rated at 240V, 480V and 600V. For other than rated voltage capacity = (Voltage/Related Voltage)2 x Rated Capacity.
(a) Field converted to 460V

64

SS-PRC028-EN

Performance Data

Table 48.

Steam Heating Coil Capacity - Air Handlers Steam Pressure (PSIG)


Steam Pressure (PSIG)
2 PSI

Unit
Airflow EAT LAT
Model No. (CFM) (F) (a)
1600

TWE061D
TWE061E

2000

2400

2400

TWE090D
TWE090E

3000

3600

3200

TWE120D
TWE120E

4000

4800

4000

TWE150E

5000

6000

5 PSI

Cond.
MBh lb/
LAT
(b)
(a)
hr(c)

10 PSI

Cond.
MBh lb/
LAT
(b)
(a)
hr(c)

15 PSI

Cond.
MBh lb/
LAT
(b)
(a)
hr(c)

25 PSI

Cond.
MBh lb/
LAT
(b)
(a)
hr(c)

MBh
(b)

Cond.
lb/
hr(c)

40

97

99

103

100

104

108

104

111

117

108

117

124

113

127

136

60

111

88

91

114

93

97

118

100

105

121

106

112

127

116

124

80

125

77

80

127

82

85

131

89

94

135

95

101

140

105

112

40

90

108

112

93

114

118

96

122

128

99

129

136

104

139

149

60

104

96

100

107

102

106

111

110

115

114

116

123

119

127

136

80

119

84

87

121

90

93

125

98

102

128

104

110

133

115

123

40

85

116

120

87

123

127

90

131

137

93

138

146

98

150

160

60

100

104

107

102

110

114

105

118

124

108

125

132

113

137

146

80

115

91

94

117

97

100

120

105

110

123

112

118

127

123

132

40

102

162

168

106

171

177

110

182

191

114

192

203

120

208

222

60

115

144

149

119

152

158

123

164

172

127

174

184

133

190

203

80

129

126

130

132

134

140

136

146

153

140

155

164

146

171

183

40

95

178

183

97

187

194

101

200

209

105

210

222

110

228

244

60

109

158

163

111

167

174

115

180

188

119

190

201

124

208

222

80

122

138

143

125

147

153

129

160

168

132

170

180

138

188

201

40

89

191

197

91

201

208

95

215

225

97

226

239

103

245

262

60

103

170

175

106

180

187

110

193

203

112

205

216

117

224

239

80

118

149

154

121

158

164

124

172

180

127

183

194

132

202

216

40

99

203

210

102

214

222

106

229

240

109

241

254

115

261

279

60

112

181

187

115

191

199

119

206

216

123

218

230

129

238

255

80

126

158

164

129

169

175

133

183

192

136

195

206

142

215

230

40

91

222

229

94

234

243

98

250

262

101

264

278

106

286

306

60

106

198

204

108

209

217

112

225

236

115

239

252

120

261

279

80

120

173

179

123

184

192

126

200

210

129

214

226

134

236

252

40

86

239

246

88

251

261

92

269

282

94

284

299

99

307

329

60

101

212

219

103

225

233

107

242

254

109

257

271

114

280

300

80

116

186

192

118

198

206

121

215

226

124

230

243

129

253

271

40

103

274

283

106

288

299

111

308

323

115

325

343

121

352

376

60

116

244

252

119

258

268

124

277

291

128

294

310

134

321

343

80

129

213

220

132

227

236

137

247

259

141

263

278

147

290

310

40

95

300

309

98

316

328

102

337

354

106

356

346

111

286

412

60

109

267

275

112

282

293

116

304

318

119

322

340

125

352

376

80

123

234

241

126

249

259

130

270

283

133

288

305

139

318

340

40

90

322

332

92

339

352

96

363

380

99

383

404

104

415

444

60

104

287

296

107

303

315

110

327

342

113

347

366

118

379

405

80

119

251

259

121

268

278

125

291

305

128

310

328

133

342

366

Continued on next page

SS-PRC028-EN

65

Performance Data

Table 48. (continued) Steam Heating Coil Capacity - Air Handlers Steam Pressure (PSIG)
Steam Pressure (PSIG)
2 PSI
Unit
Airflow EAT LAT
Model No. (CFM) (F) (a)
4800

TWE180E

6000

7200

6400

TWE240E

8000

9600

MBh
(b)

5 PSI
Cond.
lb/
LAT
(a)
hr(c)

MBh
(b)

10 PSI
Cond.
lb/
LAT
(a)
hr(c)

MBh
(b)

15 PSI
Cond.
lb/
LAT
(a)
hr(c)

MBh
(b)

25 PSI
Cond.
lb/
LAT
(a)
hr(c)

MBh
(b)

Cond.
lb/
hr(c)

40

97

295

304

100

310

322

104

332

348

107

350

369

113

379

406

60

110

262

271

113

278

288

117

299

313

121

317

334

126

346

370

80

124

230

237

127

245

254

131

266

279

134

284

299

140

313

334

40

90

322

332

92

339

352

96

363

380

99

383

404

104

415

444

60

104

287

296

107

303

315

110

327

343

113

347

366

118

379

405

80

119

251

259

121

268

278

125

291

305

128

310

328

133

342

366

40

84

346

356

87

364

378

90

390

408

93

411

434

97

446

477

60

99

308

318

102

326

338

105

351

368

108

373

393

112

407

435

80

115

270

278

117

287

299

120

313

327

123

334

352

127

368

394

40

95

379

391

97

399

414

102

427

447

105

450

475

110

488

522

60

109

337

348

111

357

371

115

384

403

119

408

430

124

445

476

80

123

295

305

125

315

327

129

342

358

133

365

385

138

402

430

40

88

414

426

90

436

452

94

467

488

97

492

519

102

534

571

60

102

368

380

105

390

405

108

420

440

111

446

470

116

487

521

80

117

322

333

120

344

357

123

374

392

126

399

421

131

440

471

40

83

443

457

85

468

485

88

501

524

91

529

558

95

574

613

60

98

395

407

100

418

434

103

451

473

106

479

505

110

524

560

80

113

346

357

115

369

383

119

402

421

121

429

453

125

473

506

Notes: Type NS Coil, 1 Row, 1" OD, SF Fins, 132 Fins per Foot.

(a)LAT - Leaving Air Temperature (F)


(b)MBh Capacity: BTU/HR/1000
(c) Cond. Lb/Hr - Condensate pound per hour

66

SS-PRC028-EN

Performance Data

Table 49. Hot Water Heating Coil Capacity - Air Handler

Tons

Unit
Model
No.

Airflow
(CFM)
1600

TWE061D
TWE061E

2000

2400

2400

TWE090D
TWE090E

3000

3600

3200

10

TWE120D
TWE120E

4000

4800

4000

12

TWE150E

5000

6000

4800

15

TWE180E

6000

7200

6400

20

TWE240E

8000

9600

Entering
Air
Temp.
(F)

GPM(a)

20.0
MBh(b)

40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80

10.9
9.0
7.2
12.3
10.2
8.1
13.5
11.2
9.0
17.0
14.2
11.4
19.3
16.1
12.9
21.2
17.7
14.2
24.5
20.2
15.9
27.8
22.9
18.1
30.7
25.3
19.9
31.7
26.4
21.1
36.0
29.9
23.8
39.7
32.9
26.2
35.2
29.3
23.3
40.0
33.3
26.4
44.2
36.6
29.1
46.8
39.0
31.2
53.0
44.2
35.3
58.6
48.8
39.0

106.1
88.3
70.6
119.8
99.6
79.5
132.0
109.6
87.4
165.9
138.4
111.1
187.9
156.7
125.5
207.3
172.7
138.2
239.1
197.3
155.6
271.7
223.8
176.2
300.0
246.9
194.0
318.0
264.4
210.9
360.6
299.6
238.7
397.0
329.6
262.3
343.9
285.7
227.7
390.3
323.9
257.7
431.3
357.6
284.2
456.2
380.2
304.5
517.5
430.9
344.6
572.0
475.9
380.2

Entering Water Temperature (F)


180
Water Temperature Drop (F)
30.0
LAT(c)
GPM(a) MBh(b)
LAT(c)
GPM(a)
101.0
111.0
121.0
95.0
106.0
117.0
91.0
102.0
114.0
104.0
113.0
123.0
98
108.0
119.0
93.0
104.0
115.0
109.0
117.0
125.0
103.0
112.0
121.0
98.0
107.0
117.0
113.3
120.9
128.6
106.5
115.3
124.0
101.0
110.7
120.3
106.0
115
124.0
100.0
110.0
120.0
95.0
106.0
116.0
106.0
115.0
124.0
100.0
110.0
120.0
94.0
106.0
116.0

6.6
5.4
4.2
7.4
6.1
4.7
8.1
6.6
5.2
10.4
8.5
6.7
11.7
9.6
7.5
12.9
10.6
8.3
14.3
11.5
8.6
16.2
13.0
9.7
17.8
14.3
10.7
19.2
15.6
12.1
21.7
17.6
13.6
23.8
19.3
14.9
21.2
17.2
13.3
23.9
19.5
15.0
26.4
21.4
16.5
28.4
23.3
18.2
32.1
26.3
20.5
35.4
28.9
22.5

96.5
79.1
61.8
108.6
88.8
69.2
119.2
97.4
75.7
152.3
125.2
98.3
171.9
141.1
110.6
189.1
155.0
121.2
210.0
168.4
126.1
237.5
190.3
142.6
261.3
209.1
156.7
287.7
234.4
181.1
325.2
264.5
203.8
357.0
290.0
223.1
310.3
252.7
195.0
350.8
285.3
219.9
386.5
313.9
241.6
416.5
341.2
266.0
470.9
385.2
299.8
519.1
424.2
329.6

96.0
106.0
116.0
90.0
101.0
112.0
86.0
97.0
109.0
98.0
108.0
118.0
93
103.0
114.0
88.0
100.0
111.0
100.0
108.0
116.0
95.0
104.0
113.0
90.0
100.0
110.0
106.3
114.0
121.7
100.0
108.8
117.6
94.9
104.6
114.3
100.0
108.0
117.0
94.0
104.0
114.0
89.0
100.0
111.0
100.0
109.0
118.0
94.0
104.0
115.0
90.0
101.0
112.0

4.5
3.6
2.7
5.0
4.0
3.0
5.5
4.4
3.3
7.1
5.7
4.4
8.0
6.4
4.9
8.8
7.1
5.4
9.1
6.9
4.0
10.3
7.8
5.0
11.3
8.6
5.6
12.8
10.2
7.4
14.4
11.4
8.4
15.8
12.5
9.1
14.1
11.2
8.2
15.9
12.6
9.2
17.5
13.8
10.1
19.3
15.4
11.6
21.7
17.4
13.0
23.9
19.1
14.3

40.0
MBh(b)

LAT(c)

87.4
70.3
53.4
97.9
78.6
59.6
107.1
85.9
64.9
139.2
112.5
86.1
156.5
126.3
96.5
171.6
138.3
105.4
178.7
134.8
78.7
201.9
153.3
97.3
221.7
168.9
110.2
256.5
203.2
148.9
288.8
228.3
167.5
316.1
249.5
182.8
276.3
218.5
159.9
311.4
246.2
180.5
342.1
270.6
198.3
376.7
301.7
227.0
424.5
339.6
255.2
466.8
373.3
280.0

90.0
100.0
111.0
851.0
96.0
107.0
811.0
931.0
105.0
93.0
103.0
113.0
88
991.0
110.0
84.0
95.0
107.0
91.0
99.0
103.0
86.0
95.0
102.0
82.0
92.0
101.0
99.1
106.9
114.3
93.3
102.1
110.9
88.6
98.3
108.1
93.0
102.0
111.0
884.0
98.0
108.0
84.0
95.0
105.0
94.0
103.0
113.0
89.0
99.0
109.0
85.0
96.0
107.0

Continued on next page

SS-PRC028-EN

67

Performance Data

Table 49. Hot Water Heating Coil Capacity - Air Handler (continued)

Tons

Unit
Model
No.

Entering
Airflow Air Temp.
(CFM)
(F)
GPM(a)

20.0
MBh(b)

40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
37.3
32.0
26.6
42.4
36.3
30.2
46.7
40.0
33.2
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80

124.9
107.0
89.1
141.3
120.9
100.6
155.8
133.3
110.8
194.8
167.1
139.6
220.9
189.4
158.1
244.0
209.1
174.3
284.7
242.6
200.6
324.1
275.8
227.7
358.3
304.7
251.3
126.3
134.0
141.6
118.5
127.2
135.9
112.0
121.7
131.3
406.0
347.5
289.1
461.4
394.6
327.9
510.4
436.3
362.2
536.5
460.2
384.0
609.2
522.2
435.4
673.9
577.4
481.0

1600

TWE061D
TWE061E

2000

2400

2400

TWE090D
TWE090E

3000

3600

3200

10

TWE120D
TWE120E

4000

4800

4000

12

TWE150E

5000

6000

4800

15

TWE180E

6000

7200

6400

20

TWE240E

8000

9600

12.9
11.0
9.2
4.5
12.4
10.4
6.0
3.7
11.4
20.0
17.2
14.4
22.7
9.5
16.3
25.1
21.5
17.9
29.3
25.0
20.6
33.4
28.4
23.4
36.9
31.4
25.9
374.5
320.9
267.4
425.4
364.3
303.2
468.8
401.2
333.6
41.8
35.8
29.8
7.5
40.6
33.8
52.5
44.9
37.3
55.2
47.4
39.5
62.7
53.8
44.8
69.4
59.4
49.5

Entering Water Temperature (F)


200.0
Water Temperature Drop (F)
30.0
LAT(c)
GPM(a) MBh(b)
LAT(c)
GPM(a)
112.0
122.0
131.0
105.0
116.0
126.0
100.0
111.0
123.0
115.0
124.0
134.0
108
118.0
129.0
102.0
113.0
125.0
122.0
130.0
138.0
115.0
124.0
132.0
109.0
118.0
128.0
23.0
19.4
15.9
26.0
22.0
17.9
28.6
24.2
19.7
118.0
127.0
135.0
111.0
121.0
130.0
105.0
116.0
126.0
117.0
126.0
135.0
110.0
120.0
130.0
105.0
115.0
126.0

7.9
6.7
5.5
8.9
7.5
6.2
9.8
8.3
6.8
12.4
10.6
8.7
14.0
11.9
9.8
15.5
13.1
10.8
17.6
14.7
11.9
19.9
16.7
13.4
22.0
18.4
14.8
345.9
292.5
293.1
391.7
330.8
269.9
430.6
363.3
296.1
25.6
21.6
17.7
29.0
24.5
19.9
32.0
27.0
22.0
34.1
28.9
23.8
38.6
32.7
26.8
42.7
36.1
29.6

115.4
97.8
80.2
130.1
110.1
90.2
143.1
120.9
98.9
181.2
153.9
126.8
204.9
173.9
143.0
225.7
191.4
157.1
256.8
215.2
173.6
291.0
243.6
196.2
320.7
268.1
215.6
119.7
127.4
135.1
112.2
121.0
129.8
106.2
115.8
125.5
373.4
315.4
257.6
423.0
356.9
291.0
466.7
393.5
320.5
497.8
422.1
346.5
563.8
477.6
391.5
622.3
526.8
431.4

106.0
116.0
126.0
100.0
111.0
122.0
95.0
106.0
118.0
110.0
119.0
129.0
103.0
113.0
124.0
981.0
109.0
120.0
114.0
122.0
130.0
107.0
116.0
125.0
102.0
111.0
121.0
15.8
13.1
10.5
17.8
14.8
11.8
19.5
16.2
12.9
112.0
121.0
129.0
105.0
115.0
125.0
100.0
110.0
121.0
112.0
121.0
130.0
105.0
115.0
125.0
100.0
111.0
121.0

5.5
4.6
3.7
6.1
5.1
4.1
6.7
5.6
4.5
8.6
7.2
5.9
9.7
8.2
6.6
0.7
9.0
7.2
11.7
9.6
7.4
13.3
10.8
8.4
14.6
11.9
9.2
316.5
263.1
209.7
357.2
296.5
235.8
391.7
324.8
257.8
17.5
14.6
11.6
19.8
16.4
13.1
21.8
18.0
14.3
23.6
19.7
15.9
26.6
22.2
17.9
29.3
24.5
19.6

40.0
MBh(b)

LAT(c)

106.3
88.9
71.7
119.4
99.7
80.3
131.0
109.2
87.8
168.2
141.2
114.3
189.6
159.0
128.5
208.4
174.4
140.9
228.6
186.9
144.3
258.2
211.0
163.2
283.7
231.6
179.4
113.0
120.7
128.3
105.9
114.7
123.5
100.2
109.9
119.6
341.0
283.4
225.7
385.0
319.6
254.3
423.8
351.4
279.5
459.4
384.2
308.9
518.8
433.3
347.9
571.5
476.7
382.6

101.0
111.0
121.0
95.0
106.0
117.0
90.0
102.0
114.0
105.0
114.0
124.0
98.0
109.0
119.0
93.0
105.0
116.0
106.0
114.0
122.0
99.0
109.0
118.0
94.0
104.0
114.0
37.3
32.0
26.6
42.4
36.3
30.2
46.7
40.0
33.2
105.0
114.0
123.0
99.0
109.0
119.0
94.0
105.0
116.0
106.0
115.0
124.0
100.0
110.0
120.0
95.0
106.0
117.0

Continued on next page

68

SS-PRC028-EN

Performance Data

Table 49. Hot Water Heating Coil Capacity - Air Handler (continued)

Tons

Unit
Model
No.

Entering
Airflow Air Temp.
(CFM)
(F)
GPM(a)

20.0
MBh(b)

40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40.1
34.7
29.4
45.5
39.4
33.4
50.2
43.5
36.7
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80
40
60
80

134.3
116.3
98.4
152.0
131.6
111.2
167.7
145.1
122.6
209.2
181.5
153.9
237.4
205.8
174.4
262.3
227.3
192.4
307.4
265.1
223.0
350.2
301.7
253.4
387.4
333.6
279.9
132.8
140.5
148.1
124.4
133.1
141.8
117.5
127.1
136.7
437.0
378.3
319.8
496.8
429.9
363.0
549.8
475.5
401.3
576.5
500.0
423.7
654.9
567.8
480.7
724.6
628.0
531.4

1600

TWE061D
TWE061E

2000

2400

2400

TWE090D
TWE090E

3000

3600

3200

10

TWE120D
TWE120E

4000

4800

4000

12

TWE150E

5000

6000

4800

15

TWE180E

6000

8000

6400

20

TWE240E

8000

9600

13.9
12.0
10.2
15.7
13.6
11.5
17.3
15.0
12.6
21.6
18.7
15.9
24.5
21.2
18.0
27.1
23.4
19.8
31.7
27.4
23.0
36.1
31.1
26.1
40.0
34.4
28.9
402.7
349.1
295.5
457.6
396.4
335.3
504.5
436.8
369.2
45.1
39.0
33.0
51.3
44.4
37.5
56.7
49.1
41.4
59.5
51.6
43.7
67.6
58.6
49.6
74.8
64.8
54.8

Entering Water Temperature (F)


210.0
Water Temperature Drop (F)
30.0
LAT(c)
GPM(a) MBh(b)
LAT(c)
GPM(a)
117.0
127.0
137.0
110.0
121.0
131.0
104.0
116.0
127.0
120.0
130.0
139.0
113.0
123.0
134.0
107.0
118.0
129.0
129.0
136.0
144.0
121.0
130.0
138.0
114.0
124.0
134.0
24.9
21.3
17.8
28.2
24.1
20.1
31.0
26.5
22.1
124.0
133.0
141.0
116.0
126.0
136.0
110.0
121.0
131.0
123.0
132.0
141.0
115.0
125.0
135.0
110.0
120.0
131.0

8.6
7.4
6.1
9.7
8.3
6.9
10.6
9.1
7.6
13.4
11.6
9.7
15.2
13.1
10.9
16.8
14.4
12.0
19.2
16.4
13.5
21.8
18.5
15.3
24.1
20.4
16.8
374.7
321.3
267.8
424.6
363.7
302.7
467.1
399.7
332.4
27.8
23.8
19.8
31.5
27.0
22.4
34.8
29.8
24.7
37.0
31.8
26.6
41.9
36.0
30.0
46.3
39.7
33.1

124.8
107.1
89.5
140.9
120.7
100.7
155.0
132.8
110.6
195.7
168.3
141.0
221.5
190.3
159.2
244.1
209.6
175.2
279.9
238.2
196.5
317.6
269.9
222.3
350.3
297.3
244.6
126.4
134.1
141.7
118.3
127.1
135.8
111.8
121.4
131.1
404.7
346.6
288.6
458.9
392.6
326.5
506.7
433.1
359.8
538.3
462.4
386.6
610.0
523.6
437.3
673.8
578.0
482.2

112.0
122.0
132.0
105.0
116.0
126.0
99.0
111.0
122.0
115.0
125.0
134.0
108.0
118.0
129.0
102.0
114.0
125.0
121.0
129.0
137.0
113.0
122.0
131.0
107.0
117.0
127.0
17.2
14.6
11.9
19.5
16.5
13.4
21.4
18.0
14.7
118.0
127.0
135.0
110.0
120.0
130.0
105.0
115.0
126.0
118.0
127.0
136.0
110.0
120.0
130.0
105.0
115.0
126.0

6.0
5.1
4.2
6.7
5.7
4.7
7.4
6.2
5.1
9.4
8.0
6.6
10.6
9.0
7.4
11.7
9.9
8.2
13.0
10.9
8.7
14.7
12.3
9.8
16.2
13.5
10.8
346.1
292.7
239.2
391.0
330.2
269.4
429.1
362.0
294.9
19.2
16.2
13.3
21.7
18.3
14.9
23.9
20.2
16.4
25.8
21.9
18.0
29.1
24.7
20.3
32.1
27.2
22.3

40.0
MBh(b)

LAT(c)

115.8
98.3
80.9
130.2
110.5
90.7
142.9
121.0
99.3
182.7
155.6
28.6
206.2
175.4
144.7
226.8
192.6
158.7
252.6
211.0
169.1
285.5
238.2
190.8
313.9
261.7
209.5
119.8
127.5
135.1
112.1
120.9
129.7
105.9
115.6
125.3
372.9
315.2
257.5
421.5
355.8
290.3
464.3
391.5
319.0
500.5
425.0
349.7
565.7
479.9
394.2
623.6
528.4
433.5

107.0
117.0
127.0
100.0
111.0
122.0
95.0
106.0
118.0
110.0
120.0
129.0
103.0
114.0
124.0
98.0
109.0
121.0
113.0
121.0
129.0
106.0
115.0
124.0
100.0
110.0
120.0
40.1
34.7
29.4
45.5
39.4
33.4
50.2
43.5
36.7
112.0
120.0
129.0
105.0
115.0
125.0
99.0
110.0
121.0
112.0
121.0
130.0
105.0
115.0
125.0
100.0
111.0
122.0

(a) GPM - Gallons Per Minute


(b) MBh Capacity: BTU/HR/1000
(c) LAT - Leaving Air Temperature (F)

SS-PRC028-EN

69

Performance Data

Table 50. Hot Water Heating Coil - Water Side Pressure Drop @ 180F Entering Water Temperature - Air Handler
Gallons Per Minute (GPM)
Tons

Unit Model
No.

10

12

14

16

18

20

22

24

26

28

30

32

34

36

38

Pressure Drop (Ft. of Water)

TWE061D,E

.02

.07

.15

.26

.40

.56

.75

.97

1.22

1.49

1.78

TWE090D,E

.06

.11

.16

.23

.30

.39

.48

.58

.70

.82

.95

10

TWE120D,E

.06

.09

.13

.17

.22

.27

.33

.39

.46

.54

.62

.70

.79

12

TWE150E

.11

.15

.20

.26

.32

.39

.47

.55

.64

.73

.83

.94

1.05 1.17 1.29

15

TWE180E

.11

.15

.20

.26

.32

.39

.47

.55

.64

.73

.83

.94

1.05 1.17 1.29

20

TWE240E

.17

.23

.30

.37

.45

.53

.63

.72

.83

.94

40

42

44

46

48

50

52

64

66

68

70

72

74

76

1.09 1.24 1.40 1.57


.89

.99

1.10

1.06 1.19 1.32 1.46

Continued
Gallons Per Minute (GPM)
Tons

Unit Model
No.

54

56

58

60

62

Pressure Drop (Ft. of Water)

TWE061D,E

TWE090D,E

10

TWE120DE

1.84

1.21 1.32 1.44 1.57 1.70

12

TWE150E

1.42 1.56 1.70 1.85 2.00

2.16

2.33

2.50

2.67

2.86

3.04 3.24 3.44 3.64 3.85 4.07

15

TWE180E

1.42 1.56 1.70 1.85 2.00

2.16

2.33

2.50

2.67

2.86

3.04 3.24 3.44 3.64 3.85 4.07

20

TWE240E

1.61 1.76 1.92 2.09 2.26

2.44

2.63

2.82

3.02

3.22

3.43 3.65 3.87 4.10 4.34 4.58 4.83 5.08 5.34

70

SS-PRC028-EN

Controls
ReliaTel Controlled Units
Zone Sensors are the building occupants comfort control devices. The following zone sensor
options are available for Odyssey units with ReliaTel control:

SS-PRC028-EN

Manual
Changeover

Manual/Automatic
Changeover

Manual/Automatic
Changeover

Heat, Cool or Off System


Switch. Fan Auto or Off
Switch. One temperature
setpoint lever.

Auto, Heat, Cool or Off System


Switch. Fan Auto or Off Switch.
Two temperature setpoint
levers.

Auto, Heat, Cool or Off System


Switch. Fan Auto or Off Switch.
Two temperature setpoint
levers. Status Indication LED
lights, System On, Heat, Cool, or
Service.

Manual/Automatic
Changeover

Remote
Sensor

Integrated Comfort
System

Auto, Heat, Cool or Off


System Switch. Fan Auto or
Off Switch. Two
temperature setpoint
levers.

Sensor(s) available for all zone


sensors to provide remote
sensing capabilities.

Sensor(s) available with


optional temperature
adjustment and override
buttons to provide central
control through a Trane
Integrated Comfort system.

71

Controls

Programmable
Night
Setback

Digital Display
Programmable
Thermostat (2H/2C)

Touchscreen
Programmable
Thermostat (2H/2C)

MON

Tue

Heat

System & Fan

Auto or manual changeover with


seven-day programming.
Keyboard selection of Heat,
Cool, Fan, Auto, or On. All
programmable sensors have
System On, Heat, Cool, Service
LED/indicators as standard.
Night Setback Sensors have one
(1) Occupied, one (1) Unoccupied, and one (1) Override
program per day.

Digital Display
Programmable Thermostat
with Built-In Relative
Humidity Sensing (3H/2C)

Auto

Override

TUE

WED

THU

FRI

SAT

FAN
ON
AUTO
CIRC

Hold Until

More

Two Heat/Two Cool digital


display thermostat. 7-day
programmable stat with
night setback shall be
available.

Digital Display
Thermostat
(3H/2C)

Tue

SUN

HEAT

SYSTEM
EM HEAT
HEAT
OFF
COOL
AUTO

RESET

DONE

EDIT

CANCEL
PERIOD

DEHUMIDIFIER

COOL

PM

WAKE

LEAVE

RETURN

SLEEP

CANCEL

Two Heat/Two Cool


programmable thermostat
with touch screen digital
display. Menu-driven
programming. Effortless setup. Program each day
separately with no need to
copy multiple days. All
programming can be done on
one screen. Easy to read and
use. Large, clear backlit digital
display.

Dual Thermistor
Remote Zone Sensor
This sensor will allow the
customer to reduce the total
number of remote sensors
to obtain space temperature
averaging. This sensor
should be utilized with
ReliaTel controls.

RA Remote Sensor

Three Heat/Two Cool digital


display thermostat with built-in
humidity control and display. This
thermostat combines both
humidity and dry bulb into one.
Fully programmable with night
setback.

72

Three Heat, Two Cool digital


display thermostat. Easy
access battery replacement.
Flip-out door for easy battery
replacement without
removing or disassembling
the thermostat.

Return Air Remote Sensor


which can be mounted in the
return air duct to report
return air temperature.

Room Remote Sensor


Space Remote Sensor which
can be mounted on the wall
to report/control from a
remote location in the
space.

SS-PRC028-EN

Electrical Data
Table 51. Electrical Characteristics Compressor and Condenser Fan Motors 60 Hz
Compressor Motor

Condenser Fan Motor


Amps

Tons

10

12

15

20

Unit
Model No.

Phase

Amps

RLA

LRA

(Ea.)

(Ea.)

No.

Volts

TTA073D3

208-230

22.4

TTA073D4

460

10.6

TTA073DK

380

TTA073DW

575

TTA090D3

208-230

TTA090D4

460

TTA090DK

380

TTA090DW

575

TTA120D3

208-230

30.1

TTA120D4

460

16.7

TTA120DK

380

19.8

TTA120DW

575

TTA120E3

208-230

TTA120E4

460

TTA120EK

380

TTA120EW

575

TTA120F3

TTA120F4

TTA120FW
TTA150E3

FLA

LRA

No.

Volts

Phase

(Ea.)

(Ea.)

149

208-230

3.1

8.1

75

460

1.6

3.8

11.3

88

380

2.7

7.9

54

575

1.2

25

164

208-230

3.1

8.1

12.9

100

460

1.6

3.8

14.3

94.3

380

2.7

10.6

78

575

1.2

225

208-230

14.4

114

460

2.5

5.8

140

380

3.4

7.8

12.4

80

575

5.1

16

110

208-230

14.4

7.8

52

460

2.5

5.8

10.4

65.6

380

3.4

7.8

38.9

575

5.1

208-230

17.6

123

208-230

14.4

460

9.6

62

460

2.5

5.8

575

6.1

40

575

5.1

208-230

22.4

149

208-230

14.4

TTA150E4

460

10.6

75

460

2.5

5.8

TTA150EK

380

11.3

88

380

3.4

7.8

TTA150EW

575

8.6

54

575

5.1

TTA180E3

208-230

25

164

208-230

14.4

TTA180E4

460

12.2

100

460

2.5

5.8

TTA180EK

380

14.3

94.3

380

3.4

7.8

TTA180EW

575

9.6

78

575

5.1

TTA180F3

208-230

25

164

208-230

14.4
5.8

TTA180F4

460

12.2

100

460

2.5

TTA180FK

380

14.3

94.3

380

3.4

7.8

TTA180FW

575

9.9

78

575

5.1

TTA240E3

208-230

39.1

267

208-230

14.4

TTA240E4

460

18.6

142

460

2.5

5.8

TTA240EK

380

23.1

160

380

3.4

7.8

TTA240EW

575

15.4

103

575

5.1

TTA240F3

208-230

39.1

267

208-230

14.4
5.8

TTA240F4

460

19.8

142

460

2.5

TTA240FK

380

23.1

160

380

3.4

7.8

TTA240FW

575

15.8

103

575

5.1

Note: Electrical characteristics reflect nameplate values and are calculated in accordance with cULus and ARI specifications.

SS-PRC028-EN

73

Electrical Data

Table 52. Unit Wiring Condensing Units 60 Hz

Tons

10

12

15

20

Unit Model Number

Unit Operating
Voltage Range

Minimum Circuit
Ampacity

Maximum Fuse or
HACR Circuit Breaker
Size(a)

TTA073D3

187-253

31.1

40

TTA073D4

414-506

14.9

20

TTA073DK

342-418

16.8

20

TTA073DW

518-632

11.1

15

TTA090D3

187-253

34.4

45

TTA090D4

414-506

17.7

25

TTA090DK

342-418

20.6

25

TTA090DW

518-632

14.5

20

TTA120D3

187-253

42.6

60

TTA120D4

414-506

23.4

30

TTA120DK

342-418

28.2

35

TTA120DW

518-632

17.5

25

TTA120E3

187-253

41.0

45

TTA120E4

414-506

20.1

25

TTA120EK

342-418

26.9

30

TTA120EW

518-632

15.5

20

TTA120F3

187-253

44.6

50

TTA120F4

414-506

24.1

30

TTA120FW

518-632

15.7

20

TTA150E3

187-253

55.4

70

TTA150E4

414-506

26.4

30

TTA150EK

342-418

28.8

35

TTA150EW

518-632

21.4

25

TTA180E3

187-253

66.3

80

TTA180E4

414-506

32.5

40

TTA180EK

342-418

39.0

45

TTA180EW

518-632

25.6

30

TTA180F3

187-253

66.3

80

TTA180F4

414-506

32.5

40

TTA180FK

342-418

39.0

45

TTA180FW

518-632

26.3

30

TTA240E3

187-253

98.0

110

TTA240E4

414-506

46.9

60

TTA240EK

342-418

58.8

70

TTA240EW

518-632

38.7

45

TTA240F3

187-253

98.0

110

TTA240F4

414-506

49.6

60

TTA240FK

342-418

58.8

70

TTA240FW

518-632

39.6

45

Note: Electrical characteristics reflect nameplate values and are calculated in accordance with cULus and ARI specifications.
7 and 10 ton values are system rated; 12, 15 and 20 ton values are condensing unit only rated.
(a) HACR type circuit breaker per NEC.

74

SS-PRC028-EN

Electrical Data

Table 53. Electrical Characteristics Standard and Low Static Motors 60 Hz Air Handler(a)
Standard Evaporator Fan Motor

Low Static Evaporator Fan Motor

Amps
Tons

10

12

15

Unit Model Number

No. Volts Phase Hp

Amps

FLA

LRA MCA MFS No. Volts Phase Hp

FLA

LRA MCA MFS

TWE061D1, E1

208

0.75

6.0

41.0

7.5

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE061D1, E1

230

0.75

5.9

45.0

7.4

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE061D3, E3

208

0.75

2.5

16.4

3.1

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE061D3, E3

230

0.75

2.4

16.4

3.0

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE061D4, E4

460

0.75

1.2

8.2

1.5

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE061DW

575

0.75

1.3

6.1

1.6

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE090D1, E1

208

1.50

6.8

31.5

8.5

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE090D1, E1

230

1.50

6.2

31.5

7.8

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE090D3, E3

208

1.50

5.3

34.3

6.6

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE090D3, E3

230

1.50

5.0

34.3

6.3

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE090D3, E3(b)

460

1.50

2.5

17.0

3.1

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

2.3

TWE090DW

575

1.50

1.8

13.6

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE120D1, E1

208

2.00

8.5

57.4 10.6

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE120D1, E1

230

2.00

7.7

57.4

9.6

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE120D3, E3

208

2.00

6.2

33.9

7.8

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE120D3, E3

230

2.00

5.8

33.9

7.3

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE120D3, E3(b)

460

2.00

2.9

33.9

3.6

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE120DW, EW

575

2.00

2.3

14.4

2.9

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE150E3

208

2.00

5.95

23.0

7.4

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE150E3

230

2.00

5.5

23.0

6.9

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE150E3(b)

460

2.00

2.75

23.0

3.4

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

2.8

TWE150EW

575

2.00

2.2

18.0

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE180E3

208

3.00

9.4

74.9 11.8

20

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE180E3

230

3.00

9.2

74.9 11.5

20

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE180E3(b)

460

3.00

4.6

39.3

5.8

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE180EW

575

3.00

3.4

24.6

4.3

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE240E3

208

5.00

14.5

98.0 18.1

25

208

3.00

9.4

74.9 11.8

20

TWE240E3

230

5.00

14.3

98.0 17.9

25

230

3.00

9.2

74.9 11.5

20

TWE240E4

460

5.00

6.7

47.0

8.4

15

460

3.00

4.6

39.3

5.8

15

TWE240EW

575

5.00

5.2

6.5

15

575

3.00

3.4

24.6

4.3

15

20

Continued on next page


(a) For additional information contact product support.
(b) Field wired for 460V.

SS-PRC028-EN

75

Electrical Data

Table 54. Electrical Characteristics High and Ultra-High Static Motors 60 Hz Air Handler(a)
High Static Evaporator Fan Motor

Ultra-High Static Evaporator Fan Motor

Amps
Tons

10

12

15

20

Unit Model Number

No. Volts Phase Hp

Amps

FLA

LRA MCA MFS No. Volts Phase Hp

FLA

LRA MCA MFS

TWE061D1, E1

208

1.50

6.8

31.5

8.5

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE061D1, E1

230

1.50

6.2

31.5

7.8

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE061D3, E3

208

1.50

5.3

34.3

6.6

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE061D3, E3

230

1.50

5.0

34.3

6.3

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE061D4, E4

460

1.50

2.5

17.0

3.1

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE061DW

575

1.50

1.8

13.6

2.3

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE090D1, E1

208

2.00

8.5

57.4 10.6

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE090D1, E1

230

2.00

7.7

57.4

9.6

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE090D3, E3

208

2.00

6.2

33.9

7.8

15

208

3.00

9.4

74.9 11.8

20

TWE090D3, E3

230

2.00

5.8

33.9

7.3

15

230

3.00

9.2

74.9 11.5

20

TWE090D3, E3(b)

460

2.00

2.9

33.9

3.6

15

460

3.00

4.6

39.3

15

5.8

TWE090DW

575

2.00

2.3

14.4

2.9

15

575

3.00

3.4

24.6

4.3

15

TWE120D1, E1

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE120D1, E1

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE120D3, E3

208

3.00

9.4

74.9 11.8

20

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE120D3, E3

230

3.00

9.2

74.9 11.5

20

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE120D3, E3(b)

460

3.00

4.6

39.3

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

5.8

TWE120DW, EW

575

3.00

3.4

24.6

4.3

15

N/A

N/A

N/A

N/A

N/A

N/A

TWE150E3

208

3.00

5.95

23.0

7.4

15

208

5.00

14.5

98.0 18.1

TWE150E3

230

3.00

5.5

23.0

6.9

15

230

5.00

14.3

98.0 17.9

25

TWE150E3(b)

460

3.00

2.75

23.0

3.4

15

460

5.00

6.7

47.0

15

18.0

2.8

8.4

25

TWE150EW

575

3.00

2.2

15

575

5.00

5.2

6.5

15

TWE180E3

208

5.00

14.5

98.0 18.1

25

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A
N/A

TWE180E3

230

5.00

14.3

98.0 17.9

25

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE180E3(b)

460

5.00

6.7

47.0

8.4

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE180EW

575

5.00

5.2

6.5

15

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

TWE240E3

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

208

7.50

20

TWE240E3

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

230

7.50

TWE240E4

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

460

7.50

9.0

61.4 11.3

20

TWE240EW

N/A

N/A

N/A

N/A

N/A

N/A

N/A

N/A

575

7.50

7.2

49.8

15

114.0 25.0

35

17.6 126.0 22.0

35

9.0

(a) For additional information contact product support.


(b) Field wired for 460V.

76

SS-PRC028-EN

Electrical Data

Table 55. Unit Wiring Air Handler 60Hz

Tons

Unit Model Number

Unit Operating
Voltage Range

Minimum Circuit
Ampacity

Maximum Fuse
or HACR Circuit
Breaker Size(a)

TWE06D1, E1

187-253

7.5

15

TWE061D3, E3

187-253

3.3

15

TWE061D4, E4

414-506

1.6

15

TWE061DK

342-418

1.8

15

TWE061DW

518-632

1.6

15

TWE090D1, E1

187-253

8.5

15

TWE090D3, E3(b)

187-253

6.6

15

TWE090D3, E3(c)

414-506

3.1

15

TWE090DK

342-418

3.1

15

TWE090DW

518-632

3.9

15

TWE120D1, E1

187-253

10.6

15

E3(b)

187-253

7.8

15

TWE120D3, E3(c)

414-506

3.6

15

TWE120DK

342-418

4.5

15

TWE120DW, EW

518-632

2.9

15

TWE120D3,
10

12

15

20

TWE150E3

187-253

6.9

15

TWE150E3(c)

414-506

3.4

15

TWE150EK

342-418

4.1

15

TWE150EW

518-632

2.8

15

TWE180E3

187-253

11.8

20

TWE180E3(c)

414-506

5.8

15

TWE180EK

342-418

9.8

15

TWE180EW

518-632

4.3

15

TWE240E3

187-253

18.1

25

TWE240E4

414-506

8.4

15

TWE240EK

342-418

10.4

15

TWE240EW

518-632

6.5

15

(a) HACR type circuit breaker per NEC.


(b) When wired for 208-230 volt.
(c) When wired for 460 volt.

SS-PRC028-EN

77

Electrical Data

Table 56. Unit Wiring with Electric Heat (Single Point Connection) 5, 7 and 10 Ton Air Handlers 60 Hz

Tons

Maximum
Fuse Heater
Used With Heater Model No. KW Rating(a)
BAYHTRL106A

10

10

78

4.33/5.76

Maximum Fuse or
Minimum Circuit
HACR Circuit
Control Stages
Ampacity(b)
Breaker Size(b)(c)
1

208-230/1/60

33/37

35/40

TWE061D1

BAYHTRL112A

8.65/11.52

59/67

60/70

TWE061E1

BAYHTRL117A

12.98/17.28

85/97

90/100

BAYHTRL123A

17.30/23.04

111/127(d)

125/150

BAYHTRL106A

4.33/5.76

34/38

35/40

60/68(d)

60/70

86/98

90/100

BAYHTRL112A

8.65/11.52

TWE090D1

BAYHTRL117A

12.98/17.28

TWE090E1

BAYHTRL123A

17.30/23.04

112/128(d)

125/150

BAYHTRL129A

21.65/28.80

138/158(d)

150/175

BAYHTRL106A

4.33/5.76

37/41

40/45

BAYHTRL112A

8.65/11.52

63/71(d)

70/80

TWE120D1

BAYHTRL117A

12.98/17.28

89/101

90/110

TWE120E1

BAYHTRL123A

17.30/23.04

115/131(d)

125/150

BAYHTRL129A

21.65/28.80

141/161(d)

150/175

BAYHTRL305A

3.75/5.00

17/19

20/20

TWE061D3

BAYHTRL310A

7.45/9.96

30/34

30/35

TWE061E3

BAYHTRL315A

11.25/14.96

43/49

45/50
70/80

TWE090D3

208-230/1/60

208-230/1/60

208-230/3/60

BAYHTRL325A

18.71/24.92

69/79(d)

BAYHTRL305A

3.75/5.00

20/22

20/25

BAYHTRL310A

7.45/9.96

33/37

35/40

BAYHTRL315A

11.25/14.96

46/52

50/60
80/90

208-230/3/60

BAYHTRL325A

18.71/24.92

72/82(d)

BAYHTRL335A

26.20/34.88

97/112(e)

100/125

BAYHTRL305A

3.75/5.00

21/23

25/25

BAYHTRL310A

7.45/9.96

34/38

35/40

TWE120D3

BAYHTRL315A

11.25/14.96

TWE120E3

BAYHTRL325A

18.71/24.92

BAYHTRL335A
BAYHTRL405A

TWE090E3

10

Unit Power
Supply

208-230/3/60

47/53

50/60

73/83(d)

80/90

26.20/34.88

98/113(e)

100/125

10

15

TWE061D4

BAYHTRL410A

9.96

TWE061E4

BAYHTRL415A

14.96

460/3/60

17

20

25

25

BAYHTRL425A

24.92

40

40

BAYHTRL405A

11

15

19

20

26

30

BAYHTRL410A

9.96

TWE090D3(f)

BAYHTRL415A

14.96

TWE090E3(f)

BAYHTRL425A

24.92

41

45

BAYHTRL435A

34.88

56

60

BAYHTRL405A

12

15

BAYHTRL410A

9.96

20

20

TWE120D3(f)

BAYHTRL415A

14.96

27

30

TWE120E3(f)

BAYHTRL425A

24.92

42

45

BAYHTRL435A

34.88

57

60

460/3/60

460/3/60

SS-PRC028-EN

Electrical Data

Table 56. Unit Wiring with Electric Heat (Single Point Connection) 5, 7 and 10 Ton Air Handlers 60 Hz

Tons

10

Maximum
Fuse Heater
Used With Heater Model No. KW Rating(a)

TWE061DW

TWE090DW

Unit Power
Supply

Maximum Fuse or
Minimum Circuit
HACR Circuit
Control Stages
Ampacity(b)
Breaker Size(b)(c)

BAYHTRLW05A

15

BAYHTRLW10A

9.96

15

15

BAYHTRLW15A

14.96

21

25

BAYHTRLW25A

24.92

575/3/60

33

35

BAYHTRLW05A

11

15

BAYHTRLW10A

9.96

17

20

BAYHTRLW15A

14.96

BAYHTRLW25A

24.92

575/3/60

23

25

36

40

BAYHTRLW35A

34.88

48

50

BAYHTRLW05A

10

15

16

20

22

25

BAYHTRLW10A

9.96

TWE120DW

BAYHTRLW15A

14.96

TWE120EW

BAYHTRLW25A

24.92

35

35

BAYHTRLW35A

34.88

47

50

575/3/60

(a) kW ratings are at: 208/240V for 208-230V air handlers.


480V for 460V air handlers
600V for 575V air handlers
For other than rated voltage, capacity = (Voltage/Rated Voltage)2 x Rated Capacity.
(b) Any power supply and circuits must be wired and protected in accordance with local codes.
(c) The HACR circuit breaker is for U.S.A. installations only.
(d) Field wire must be rated at least 75C.
(e) Field wire must be rated at least 90C.
(f) With motor field converted to 460V.

SS-PRC028-EN

79

Electrical Data

Table 57. Unit Wiring with Electric Heat (Single Point Connection) 12 - 20 Ton Air Handlers

Tons

12

15

20

12

15

20

12

15

20

Used With

TWE150E3

TWE180E3

TWE240E3

TWE150E3(e)

TWE180E3(e)

TWE240E4

TWE150EW

TWE180EW

TWE240EW

Heater
Model No.

Heater KW
Rating(a)

Unit Power
Supply

Control
Stages

Minimum Circuit
Ampacity(b)

Maximum Fuse or
HACR Circuit
Breaker Size(b)(c)
35/40

BAYHTRM310A

7.50/10.00

33/37

BAYHTRM320A

14.96/19.92

59/67

60/70

BAYHTRM330A

22.50/29.92

85/97

90/100

BAYHTRM350A

37.42/49.84

137/157

150/175

BAYHTRM310A

7.50/10.00

38/42

40/45

BAYHTRM320A

14.96/19.92

64/72

70/80

BAYHTRM330A

22.50/29.92

90/102

90/110

BAYHTRM350A

37.42/49.84

142/162(d)

150/175

BAYHTRM310A

7.50/10.00

45/49

50/50

BAYHTRM320A

14.96/19.92

71/79

80/80

BAYHTRM330A

22.50/29.92

97/109

100/110

BAYHTRM350A

37.42/49.84

149/169(d)

150/175

BAYHTRM410A

10

19

20

BAYHTRM420A

19.92

34

35

BAYHTRM430A

29.92

49

50

BAYHTRM450A

49.84

79

80

BAYHTRM410A

10

21

25

BAYHTRM420A

19.92

36

40

BAYHTRM430A

29.92

51

60

BAYHTRM450A

49.84

81

90

BAYHTRM410A

10

24

25

BAYHTRM420A

19.92

39

40

BAYHTRM430A

29.92

54

60

208-230/3/60

208-230/3/60

208-230/3/60

460/3/60

460/3/60

460/3/60

BAYHTRM450A

49.84

84

90

BAYHTRMW10A

10

15

20

BAYHTRMW20A

19.92

27

30

BAYHTRMW30A

29.92

39

40

BAYHTRMW50A

49.84

63

70

BAYHTRMW10A

10

17

20

BAYHTRMW20A

19.92

30

30

BAYHTRMW30A

29.92

42

45

BAYHTRMW50A

49.84

67

70

BAYHTRMW10A

10

20

25

BAYHTRMW20A

19.92

32

35

BAYHTRMW30A

29.92

45

45

BAYHTRMW50A

49.84

70

70

575/3/60

575/3/60

575/3/60

(a) kW ratings are at: 208/240V for 208-230V air handlers.


480V for 460V air handlers
600V for 575V air handlers
For other than rated voltage, capacity = (Voltage/Rated Voltage)2 x Rated Capacity.
(b) Any power supply and circuits must be wired and protected in accordance with local codes.
(c) The HACR circuit breaker is for U.S.A. installations only.
(d) Field wire must be rated at least 90C.
(e) With motor field wired for 460V.

80

SS-PRC028-EN

Jobsite Connections
For Electromechanical Controls
Wiring shown with dashed lines is to be furnished and installed by the customer. All customersupplied wiring must be copper only and must conform to NEC and local electrical codes. Codes
may require line of sight between disconnect switch and unit.

Note: When electric heater accessory is used, single point power entry or dual point power entry
is field optional. Single point power entry option is through electric heater only.
TTA073D/TWE090D
TTA090D/TWE090D
TTA090D/TWE120D
TTA120D/TWE120D
TTA120E/TWE120E
TTA120F/TWE120D

TTA150E/TWE150E
TTA180E/TWE180E
TTA180F/TWE180E(a)
TTA180E/TWE240E
TTA240E/TWE240E
TTA240F/TWE240E(a)

(2) TTA073D/TWE150E
(2) TTA090D/TWE180E
(2) TTA120D/TWE240E
(2) TTA120F/TWE240E

(a) Need to manifold the dual circuit indoor unit when connecting to a Manifolded outdoor unit.

Field Wiring:
A. 3 power wires. Line voltage for 3 phase (2 wires for single phase)
B. 3 power wires. Line voltage for 3 phase (2 wires for single phase)
C. Cooling only thermostat: 3 to 7 wires depending on stages of electric heat
D. 3 to 7 wires depending on type of outdoor unit(s)

SS-PRC028-EN

81

Jobsite Connections

For ReliaTel Controls


Wiring shown with dashed lines is to be furnished and installed by the customer. All customersupplied wiring must be copper only and must conform to NEC and local electrical codes. Codes
may require line of sight between disconnect switch and unit.

Notes:
1. When electric heater accessory is used, single point power entry or dual point power entry is
field optional. Single point power entry option is through electric heater only.
2. ***Choose only one of the following; Thermostat, Zone Sensor, or NSB Panel.
TTA073D/TWE090D
TTA090D/TWE090D
TTA120D/TWE120D
TTA120E/TWE120E
TTA120F/TWE120D

TTA120F/TWE120E(a)
TTA150E/TWE150E
TTA180E/TWE180E
TTA180F/TWE180E(a)
TTA240E/TWE240E

TTA240F/TWE240E(a)
(2) TTA073D/TWE150E
(2) TTA090D/TWE180E
(2) TTA120D/TWE240E
(2) TTA120F/TWE240E

(a) Need to manifold the dual circuit indoor unit when connecting to a Manifolded outdoor unit.

Field Wiring:
A. 3 power wires, line voltage for 3 phase, (2 power wires for single phase)
B. 3 power wires, line voltage for 3 phase, (2 power wires for single phase)
C. Cooling only thermostat: 3 to 7 wires depending on stages of electric heat
Zone Sensor: 4 to 10 wires depending on zone sensor model 1
D. 3 to 7 wires depending on type of outdoor unit(s).

82

See Zone Sensor wiring instructions for wiring information (ReliaTel Controls only).

SS-PRC028-EN

Jobsite Connections

This page intentionally left blank.

SS-PRC028-EN

83

Typical Wiring
Figure 17. Typical Single & Dual Compressor - Electromechanical Connection Diagram

84

SS-PRC028-EN

Typical Wiring

Figure 17. (continued from previous page) Typical Single & Dual Compressor - Electromechanical Connection Diagram

SS-PRC028-EN

85

Typical Wiring

Figure 18. Typical Single Compressor - Connection Diagram

86

SS-PRC028-EN

Typical Wiring

Figure 18. (continued from previous page) Typical Single Compressor - Connection Diagram

SS-PRC028-EN

87

Typical Wiring

Figure 19. Typical Dual Compressor - Connection Diagram

88

SS-PRC028-EN

Typical Wiring

Figure 19. (continued from previous page) Typical Dual Compressor - Connection Diagram

SS-PRC028-EN

89

Typical Wiring

Figure 20. Typical Power/Control Diagram (Single and Dual Compressor)

90

SS-PRC028-EN

Typical Wiring

Figure 20. (continued from previous page) Typical Power/Control Diagram (Single and Dual Compressor)

SS-PRC028-EN

91

Typical Wiring

Figure 21. Typical Air Handler Power/Control and Connection Diagram

92

SS-PRC028-EN

Typical Wiring

Figure 21. (continued from previous page) Typical Air Handler Power/Control and Connection Diagram

SS-PRC028-EN

93

Dimensional Data
Figure 22. 6-7 1/2 Ton Condensing Unit, Single Compressor
SEE NOTE 3
NOTES:
1. ACCESS OPENING IS FOR FIELD INSTALLED BAYLOAM ACCESSORY.
2. MINIMUM CLEARANCE FOR PROPER OPERATION IS 36" FROM
WALLS, SHRUBBERY, PRIVACY FENCES ETC. MINIMUM CLEARANCE
BETWEEN ADJACENT UNITS IS 72". RECOMMENDED SERVICE
CLEARANCE 48"
3. TOP DISCHARGE AREA SHOULD BE UNRESTRICTED FOR 100"
MINIMUM. UNIT SHOULD BE PLACED SO ROOF RUN-OFF WATER DOES
NOT POUR DIRECTLY ON UNIT
4. OUTDOOR AIR TEMPERATURE SENSOR OPENING (DO NOT BLOCK OPENING)

SERVICE PANEL

SEE NOTE 4
HAIL GUARD
(OPTIONAL)

SERVICE CLEARANCE
48" (SEE NOTE 2
FOR CLEARANCE)
HAIL GUARD
(OPTIONAL)

SEE NOTE 1
REFRIGERANT ACCESS

35 15/16"
WITH HAIL GUARD

LINE VOLTAGE

33 7/8"
CONTROL WIRING

SERVICE PANEL

39 3/16"

34 1/8"

26 15/16"

29 13/16"

14 3/8"

16 7/16"
1/16"
7 15/16"

6"

2 7/8"

6"

SUCTION LINE

1 7/8"

21 11/16"

40 15/16"

LIQUID LINE
33 13/16"

41 15/16"
WITH HAIL GUARD

SERVICE PANEL SIDE


3"

7/16" DIA. ISOLATOR MOUNTING


HOLES (OUTSIDE HOLES - 4 PLACES)

BOTTOM
OF UNIT

40 3/4" 34 3/4"

4 3/16"
1 13/16"

94

27 11/16"

2 5/16"

SS-PRC028-EN

Dimensional Data

Figure 23. 10 Ton Condensing Unit, Single Compressor


SEE NOTE 3

NOTES:
1. ACCESS OPENING IS FOR FIELD INSTALLED BAYLOAM ACCESSORY.
2. MINIMUM CLEARANCE FOR PROPER OPERATION IS 36" FROM
WALLS, SHRUBBERY, PRIVACY FENCES ETC. MINIMUM CLEARANCE
BETWEEN ADJACENT UNITS IS 72". RECOMMENDED SERVICE
CLEARANCE 48"
3. TOP DISCHARGE AREA SHOULD BE UNRESTRICTED FOR 100"
MINIMUM. UNIT SHOULD BE PLACED SO ROOF RUN-OFF WATER DOES
NOT POUR DIRECTLY ON UNIT
4. OUTDOOR AIR TEMPERATURE SENSOR OPENING (DO NOT BLOCK OPENING)

SERVICE PANEL

HAIL GUARD
(OPTIONAL)

SEE NOTE 4

SERVICE CLEARANCE
48" (SEE NOTE 2
FOR CLEARANCE
SEE NOTE 1

39 15/16"

REFRIGERANT ACCESS

WITH HAIL GUARD

4 1/4"

HAIL GUARD
(OPTIONAL)

1 1/4"

37 15/16"

LINE VOLTAGE
CONTROL WIRING

SERVICE PANEL

39 1/8"

34 1/16"

26 7/8"

29 3/4"

14 5/16"

7 1/2" 8 1/4"
1/16"

SUCTION LINE

6"

1 15/16"

1 7/8"
25 11/16"

6"

LIQUID LINE

2 7/8"

4 15/16"

50 15/16"

37 11/16"

51 15/16"
WITH HAIL GUARD
SERVICE PANEL SIDE
7/16" DIA. ISOLATOR MOUNTING
HOLES (OUTSIDE HOLES - 4 PLACES)

3"

50 3/4"

44 3/4"

BOTTOM
OF UNIT

3 13/16"
2 3/16"

SS-PRC028-EN

31 11/16"

1 11/16"

95

Dimensional Data

Figure 24. 10 Ton Condensing Unit, Dual Compressor


SEE NOTE 3
NOTES:
1. ACCESS OPENING IS FOR FIELD INSTALLED BAYLOAM ACCESSORY.
2. MINIMUM CLEARANCE FOR PROPER OPERATION IS 36" FROM
WALLS, SHRUBBERY, PRIVACY FENCES ETC. MINIMUM CLEARANCE
BETWEEN ADJACENT UNITS IS 72". RECOMMENDED SERVICE
CLEARANCE 48"
3. TOP DISCHARGE AREA SHOULD BE UNRESTRICTED FOR 100"
MINIMUM. UNIT SHOULD BE PLACED SO ROOF RUN-OFF WATER DOES
NOT POUR DIRECTLY ON UNIT
4. OUTDOOR AIR TEMPERATURE SENSOR OPENING (DO NOT BLOCK OPENING).

SERVICE PANEL

HAIL GUARD
(OPTIONAL)

SEE NOTE 4

SERVICE CLEARANCE
48" (SEE NOTE 2
FOR CLEARANCE)

39 15/16"
WITH HAIL GUARD

HAIL GUARD
(OPTIONAL)

1 1/4"

37 15/16"

LINE VOLTAGE

4 1/4"

SEE NOTE 1
REFRIGERANT ACCESS

CONTROL WIRING

SERVICE PANEL

34 1/16"

39 1/8"

29 3/4"

26 7/8"
14 5/16"

6 3/8" 7 7/8" 9 1/4"10 3/8"


1/16"

LIQUID LINE

6"
SUCTION LINE

1 7/8"
25 11/16"

6"
2 7/8"

5 1/16"

50 15/16"

37 11/16"

3 15/16"

51 15/16"
WITH HAIL GUARD

2 1/2"
SERVICE PANEL SIDE

3"

50 3/4"

44 3/4"

7/16" DIA. ISOLATOR MOUNTING


HOLES (OUTSIDE HOLES - 4 PLACES)

BOTTOM
OF UNIT

3 13/16"
2 3/16"

96

31 11/16"

1 11/16"

SS-PRC028-EN

Dimensional Data

Figure 25. 10 Ton Condensing Unit, Manifolded Compressor


SEE NOTE 3

SERVICE PANEL

HAIL GUARD
(OPTIONAL)

SEE NOTE 4

NOTES:
1. ACCESS OPENING IS FOR FIELD INSTALLED BAYLOAM ACCESSORY.
2. MINIMUM CLEARANCE FOR PROPER OPERATION IS 36" FROM
WALLS, SHRUBBERY, PRIVACY FENCES ETC. MINIMUM CLEARANCE
BETWEEN ADJACENT UNITS IS 72". RECOMMENDED SERVICE
CLEARANCE 48"
3. TOP DISCHARGE AREA SHOULD BE UNRESTRICTED FOR 100"
MINIMUM. UNIT SHOULD BE PLACED SO ROOF RUN-OFF WATER DOES
NOT POUR DIRECTLY ON UNIT
4. OUTDOOR AIR TEMPERATURE SENSOR OPENING (DO NOT BLOCK OPENING)

SERVICE CLEARANCE
48" (SEE NOTE 2
FOR CLEARANCE)

39 15/16"
WITH HAIL GUARD

1 1/4"

HAIL GUARD
(OPTIONAL)

4 1/4"

LINE VOLTAGE

SEE NOTE 1

REFRIGERANT ACCESS

37 15/16"

CONTROL WIRING

SERVICE PANEL

39 1/8"

29 3/4" 34 1/16"

26 7/8"
14 5/16"

8 5/16"
1/16"

SUCTION LINE
LIQUID LINE

6"

4 15/16"

1 7/8"
25 11/16"

6"
2 7/8"

1 15/16"

37 11/16"

50 15/16"
51 15/16"
WITH HAIL GUARD

SERVICE PANEL SIDE

7/16" DIA. ISOLATOR MOUNTING


HOLES (OUTSIDE HOLES - 4 PLACES)

3"

50 3/4"

44 3/4"

BOTTOM
OF UNIT

3 13/16"
2 3/16"

SS-PRC028-EN

31 11/16"

1 11/16"

97

Dimensional Data

Figure 26. 12 Ton Condensing Unit, Dual Compressor


NOTES:
1. ACCESS OPENING IS FOR FIELD INSTALLED BAYLOAM ACCESSORY.
2. MINIMUM CLEARANCE FOR PROPER OPERATION IS 36" FROM
WALLS, SHRUBBERY, PRIVACY FENCES ETC. MINIMUM CLEARANCE
BETWEEN ADJACENT UNITS IS 72". RECOMMENDED SERVICE
CLEARANCE 48"
3. TOP DISCHARGE AREA SHOULD BE UNRESTRICTED FOR 100"
MINIMUM. UNIT SHOULD BE PLACED SO ROOF RUN-OFF WATER DOES
NOT POUR DIRECTLY ON UNIT
4. OUTDOOR AIR TEMPERATURE SENSOR OPENING (DO NOT BLOCK OPENING).

SEE NOTE 3

SERVICE PANEL

SEE NOTE 4

HAIL GUARD
(OPTIONAL)

SERVICE CLEARANCE
48" (SEE NOTE 2
FOR CLEARANCE

1 1/4"
HAIL GUARD
(OPTIONAL)

39 15/16"
WITH HAIL GUARD

4 1/4"
LINE VOLTAGE

SEE NOTE 1

37 15/16"

REFRIGERANT ACESS

CONTROL WIRING

35 3/4"

SERVICE PANEL

44 3/4"

42 5/16"

6 3/8"

32 7/8"
14 5/16"

11 3/8"
7 7/8" 9 5/16"
1/16"

LIQUID LINE

6"

25 11/16"

6"

37 11/16"

SUCTION LINE

1 13/16"

2 7/8"

5 1/16"

50 15/16"

3 3/16"
SERVICE PANEL SIDE

51 15/16"
WITH HAIL GUARD

3"

7/16" DIA. ISOLATOR MOUNTING


HOLES (OUTSIDE HOLES - 4 PLACES)

50 3/4"

44 3/4"

BOTTOM
OF UNIT

3 13/16"
2 3/16"

98

31 11/16"

1 11/16"

SS-PRC028-EN

Dimensional Data

Figure 27. 15-20 Ton Condensing Unit, Dual Compressor

SEE NOTE 2

NOTES:
1. MINIMUM CLEARANCE FOR PROPER OPERATION IS 36" FROM
WALLS, SHRUBBERY, PRIVACY FENCES ETC. MINIMUM CLEARANCE
BETWEEN ADJACENT UNITS IS 72". RECOMMENDED SERVICE
CLEARANCE 48"
2. TOP DISCHARGE AREA SHOULD BE UNRESTRICTED FOR 100"
MINIMUM. UNIT SHOULD BE PLACED SO ROOF RUN-OFF WATER DOES
NOT POUR DIRECTLY ON UNIT
3. OUTDOOR AIR TEMPERATURE SENSOR OPENING (DO NOT BLOCK OPENING)

HAIL GUARD
(OPTIONAL)
SEE NOTE 3

SERVICE CLEARANCE
48" (SEE NOTE 1
FOR CLEARANCE)

SERVICE PANEL

DETAIL A

46"
WITH HAIL GUARD

95 7/16"
WITH HAIL GUARD

44"

41 7/16"

HAIL GUARD
(OPTIONAL)

HAIL GUARD
(OPTIONAL)

45 1/8"

SERVICE
PANEL

3 3/8"

1/16"

3/16"

6 5/8"
41 3/8"

9"

25 11/16"

9"

93 5/16"

9 1/4"
6 13/16"
7/16" DIA. ISOLATOR MOUNTING
HOLES (OUTSIDE HOLES - 4 PLACES)

1 3/16"

CONTROL
WIRING

LINE VOLTAGE

SERVICE PANEL SIDE


SUCTION LINE
REFRIGERANT ACCESS
39 7/8"

BOTTOM OF UNIT

18 3/4"
36 7/8"

41 1/2"

41 5/8"

14 5/8" 12 9/16"
5 9/16"
LIQUID LINES

4 3/8"
SUCTION LINE
3"

6 5/16"

2 3/16" 6 13/16"

3 11/16"

87"

15/16"

93"

FRONT DETAIL A
DIMENSIONAL DETAIL

SS-PRC028-EN

99

Dimensional Data

Figure 28. 15-20 Ton Condensing Unit, Manifolded Compressor

SEE NOTE 2

NOTES:
1. MINIMUM CLEARANCE FOR PROPER OPERATION IS 36" FROM
WALLS, SHRUBBERY, PRIVACY FENCES ETC. MINIMUM CLEARANCE
BETWEEN ADJACENT UNITS IS 72". RECOMMENDED SERVICE
CLEARANCE 48"
2. TOP DISCHARGE AREA SHOULD BE UNRESTRICTED FOR 100"
MINIMUM. UNIT SHOULD BE PLACED SO ROOF RUN-OFF WATER DOES
NOT POUR DIRECTLY ON UNIT
3. OUTDOOR AIR TEMPERATURE SENSOR OPENING (DO NOT BLOCK OPENING)

HAIL GUARD
(OPTIONAL)
SEE NOTE 3
SERVICE CLEARANCE
48" (SEE NOTE 1
FOR CLEARANCE)

SERVICE PANEL
DETAIL A
46"
WITH HAIL GUARD

95 7/16"
WITH HAIL GUARD

44"

HAIL GUARD
(OPTIONAL)

HAIL GUARD
(OPTIONAL)

45 1/8"

1/16"

3/16"

SERVICE
PANEL

41 1/4"
9"

25 11/16"

9"

93 5/16"

6 13/16"

7/16" DIA. ISOLATOR MOUNTING


HOLES (OUTSIDE HOLES - 4 PLACES)
CONTROL WIRING
SERVICE PANEL SIDE

1 3/16"

LINE VOLTAGE
SUCTION LINE
REFRIGERANT ACCESS
39 7/8"

BOTTOM OF UNIT

36 7/8"

41 1/2"

20 1/16"

14 5/8"

4 1/8"
3"

2 3/16" 6 13/16"

41 5/8"

LIQUID LINE

87"

15/16"
3 3/8"
6 5/16"
9 1/4"

93"

FRONT DETAIL A
DIMENSIONAL DETAIL

100

SS-PRC028-EN

Dimensional Data

Figure 29. 5 Ton Air Handler, Single Circuit


22
13 1/4"

SUPPLY
OPENING

HEATER CONTROL
AND SINGLE POWER
ENTRY WIRES

37 15/16"

16"

NOTES:
1 PANEL DEPTH 1/2" (TYP.ALL PANELS).
2. REMOVABLE DRAIN PAN AND ATTACHED DRAIN CONNECTION MAY BE INSTALLED ON END
OF UNIT IN EITHER THE VERTICAL OR HORIZONTAL CONFIGURATION, PLASTIC DRAIN PAN
ACCESS PLATE ON THE END OF UNIT OPPOSITE DRAIN CONNECTION MUST BE REMOVED TO
SLIDE DRAIN PAN OUT OF UNIT FOR CLEANING. ACCESS PLATE MUST BE RE-INSTALLED AFTER
SLIDING DRAIN PAN BACK INTO UNIT.
3. IF PERIODIC DRAIN PAN CLEANING IS REQUIRED, ALLOW ROOM FOR PARTIAL REMOVAL OF
DRAIN PAN CONNECTION AT END OF UNIT.
4. 1" FEMALE SCHED. 40 PVC PIPE DRAIN CONNECTION VERTICAL CONFIGURATION.
5. 1" FEMALE SCHED. 40 PVC PIPE DRAIN CONNECTION HORIZONTAL CONFIGURATION.

7 9/16"
3 9/16"

1 5/16"

HEATER VENTILATION

2 5/16"

12 7/16"

BOTTOM RETURN

SIDE RETURN

13 5/16"

6 7/8"
1 3/4"

32 1/2"
CONTROL WIRING

32 1/2"

2 3/4"

3 7/16"
COPPER LIQUID LINE
FIELD CONNECTION

5 15/16"
13 3/16"

LINE VOLTAGE
CONTROL BOX
ACCESS PANEL

COPPER SUCTION LINE


FIELD CONNECTION

1 11/16"

O.D. SUCTION LINE

DRAIN CONNECTION
FOR HORIZONTAL
(SEE NOTE 2,3,5)

REMOTE BULB TXV


17 5/16" 16 1/8"

20 1/16"

13 9/16"

12"

12" 13 9/16"
15/16"
FILTER ACCESS PANEL
22" MIN. DISTANCE
BOTH SIDE

15/16"

SEE NOTES 2,3,4

1 3/8"

1 3/8"

1 11/16"
LIQUID LINES

3 3/16"

3 11/16"

SEE NOTES 2,3,4


(4) - HOLE FOR HORIZONTAL
SUSPENSION
1 1/8"

35 5/8"
SUPPLY OPENING

3"

(4) HOLE FOR HORIZONTAL


SUSPENSION
BOTTOM RETURN

34 9/16"

48 1/16"

SIDE RETURN

FILTER
10 7/16"

BOTTOM RETURN
SUPPLY VERTICAL RETURN HORIZONTAL /
RETURN VERTICAL

SS-PRC028-EN

SIDE RETURN
SUPPLY HORIZONTAL RETURN VERTICAL /
RETURN HORIZONTAL

101

Dimensional Data

Figure 30. 5 Ton Air Handler, Dual Circuit


22
13 1/4"

SUPPLY
OPENING

HEATER CONTROL
AND SINGLE POWER
ENTRY WIRES

37 15/16"

16"

NOTES:
1 PANEL DEPTH 1/2" (TYP.ALL PANELS).
2. REMOVABLE DRAIN PAN AND ATTACHED DRAIN CONNECTION MAY BE INSTALLED ON END
OF UNIT IN EITHER THE VERTICAL OR HORIZONTAL CONFIGURATION, PLASTIC DRAIN PAN
ACCESS PLATE ON THE END OF UNIT OPPOSITE DRAIN CONNECTION MUST BE REMOVED TO
SLIDE DRAIN PAN OUT OF UNIT FOR CLEANING. ACCESS PLATE MUST BE RE-INSTALLED AFTER
SLIDING PAN DRAIN PAN BACK INTO UNIT.
3. IF PERIODIC DRAIN PAN CLEANING IS REQUIRED, ALLOW ROOM FOR PARTIAL REMOVAL OF
DRAIN CONNECTION AT END OF UNIT.
4. 1" FEMALE SCHED. 40 PVC PIPE DRAIN CONNECTION VERTICAL CONFIGURATION.
5. 1" FEMALE SCHED. 40 PVC PIPE DRAIN CONNECTION HORIZONTAL CONFIGURATION.

7 9/16"
3 9/16"

1 5/16"

HEATER VENTILATION

2 5/16"

12 7/16"

BOTTOM RETURN

SIDE RETURN

13 5/16"

6 7/8"

1 3/4"

32 1/2"

32 1/2"
CONTROL WIRING

3 7/16"

LINE VOLTAGE

COPPER LIQUID LINE


FIELD CONNECTION

5 15/16"
13 3/16"

CONTROL BOX
ACCESS PANEL
1 11/16"

SUCTION LINE

20 1/16"
12" 13 9/16"
FILTER ACCESS PANEL
22" MIN. DISTANCE
BOTH SIDE

16 1/8" 17 5/16"

17 5/16" 16 1/8"
17 7/8"

13 9/16"

COPPER LIQUID LINE


FIELD CONNECTION

15/16"

12"

15/16"

SEE NOTES 2,3,4

1 3/8"
1 3/8"

1 11/16"

LIQUID LINES

3 3/16"

SEE NOTES 2,3,4

1 1/8"

COPPER SUCTION LINE


FIELD CONNECTION

(2) REMOTE BULB TXV

DRAIN CONNECTION
FOR HORIZONTAL
(SEE NOTE 2,3,5)

3 11/16"

(4) - HOLE FOR HORIZONTAL


SUSPENSION

35 5/8"

1 11/16"
3 11/16"

SUPPLY OPENING

(4) HOLE FOR


HORIZONTAL
SUSPENSION

BOTTOM RETURN

3"

34 9/16"

2 3/4"

SIDE RETURN

48 1/16"

FILTER

SIDE RETURN
10 7/16"

102

BOTTOM RETURN

SUPPLY VERTICAL RETURN HORIZONTAL /


RETURN VERTICAL

SUPPLY HORIZONTAL RETURN VERTICAL /


RETURN HORIZONTAL

SS-PRC028-EN

Dimensional Data

Figure 31. 7 1/2 Ton Air Handler, Single Circuit


NOTES:
1 PANEL DEPTH 1/2" (TYP.ALL PANELS).
2. REMOVABLE DRAIN PAN AND ATTACHED DRAIN CONNECTION MAY BE INSTALLED ON END
OF UNIT IN EITHER THE VERTICAL OR HORIZONTAL CONFIGURATION, PLASTIC DRAIN PAN
ACCESS PLATE ON THE END OF UNIT OPPOSITE DRAIN CONNECTION MUST BE REMOVED TO
SLIDE DRAIN PAN OUT OF UNIT CLEANING. ACCESS PLATE MUST BE RE-INSTALLED AFTER
SLIDING DRAIN PAN BACK INTO UNIT.
3. IF PERIODIC DRAIN PAN CLEANING IS REQUIRED, ALLOW ROOM FOR PARTIAL REMOVAL OF
DRAIN PAN CONNECTION AT END OF UNIT.
4. 1" FEMALE SCHED. 40 PVC PIPE DRAIN CONNECTION VERTICAL CONFIGURATION.
5. 1" FEMALE SCHED. 40 PVC PIPE DRAIN CONNECTION HORIZONTAL CONFIGURATION.

25
15 7/8"

3/4"

SUPPLY
OPENING

14 3/8"

18 3/4" 47 1/2"
HEATER CONTROL
AND SINGLE
POWER ENTRY WIRES

2 1/4"

HEATER VENTILATION

1 13/16"

1 9/16"

6 13/16"

BOTTOM RETURN

16 7/8"

SIDE RETURN

16 1/16"

12 5/16"
8 5/16"

2 3/4"

42"

42"

2 3/4"

CONTROL WIRING
3 1/2"

LINE VOLTAGE

COPPER LIQUID LINE


FIELD CONNECTION

8 13/16"

CONTROL BOX
ACCESS PANEL

16"
1 3/16"

DRAIN CONNECTION
FOR HORIZONTAL
(SEE NOTE 2,3,5)

COPPER SUCTION LINE


FIELD CONNECTION

REMOTE BULB TXV


SUCTION LINE

22 7/8"

16 11/16" 17 7/16"

FILTER ACCESS PANEL


22" MIN. DISTANCE
BOTH SIDE

20"

17 3/8"

16 11/16"

3 5/8"

1 9/16"

1 11/16"

3 1/2"

SEE NOTES 2,3,4

LIQUID LINES
SEE NOTES 2,3,4
1 3/16"

45 1/8"

(4) - HOLE FOR


HORIZONTAL SUSPENSION
(4) HOLE FOR
HORIZONTAL
SUSPENSION

SUPPLY OPENING
6 3/4"

BOTTOM RETURN
54 1/16"

36 7/8"

SIDE RETURN

FILTER

10 7/16"

BOTTOM RETURN
SUPPLY VERTICAL RETURN HORIZONTAL /
RETURN VERTICAL

SS-PRC028-EN

SIDE RETURN
SUPPLY HORIZONTAL RETURN VERTICAL /
RETURN HORIZONTAL

103

Dimensional Data

Figure 32. 7 1/2 Ton Air Handler, Dual Circuit


NOTES:
1 PANEL DEPTH 1/2" (TYP.ALL PANELS).
2. REMOVABLE DRAIN PAN AND ATTACHED DRAIN CONNECTION MAY BE INSTALLED ON END
OF UNIT IN EITHER THE VERTICAL OR HORIZONTAL CONFIGURATION, PLASTIC DRAIN PAN
ACCESS PLATE ON THE END OF UNIT OPPOSITE DRAIN CONNECTION MUST BE REMOVED TO
SLIDE DRAIN PAN OUT OF UNIT FOR CLEANING. ACCESS PLATE MUST BE RE-INSTALLED AFTER
SLIDING DRAIN PAN BACK INTO UNIT.
3. IF PERIODIC DRAIN PAN CLEANING IS REQUIRED, ALLOW ROOM FOR PARTIAL REMOVAL OF
DRAIN PAN CONNECTION AT END OF UNIT.
4. 1" FEMALE SCHED. 40 PVC PIPE DRAIN CONNECTION VERTICAL CONFIGURATION.
5. 1" FEMALE SCHED. 40 PVC PIPE DRAIN CONNECTION HORIZONTAL CONFIGURATION.

25
15 7/8"

3/4"

SUPPLY
OPENING

14 3/8"

18 3/4" 47 1/2"

HEATER CONTROL
AND SINGLE
POWER ENTRY WIRES

16 1/16"

12 5/16"
8 5/16"

HEATER
VENTILATION

2 1/4"

1 13/16"

1 9/16"

6 13/16"

BOTTOM RETURN

16 7/8"

SIDE RETURN

2 3/4"

42"

42"

2 3/4"

CONTROL WIRING
3 1/2"
LINE VOLTAGE

COPPER LIQUID LINE


FIELD CONNECTION

8 13/16"

CONTROL BOX
ACCESS PANEL

16"
1 3/16"

DRAIN CONNECTION
FOR HORIZONTAL
(SEE NOTE 2,3,5)

COPPER SUCTION LINE


FIELD CONNECTION

(2) REMOTE BULB TXV


SUCTION LINE

22 7/8"
16 1/4"
11 1/16" 13 3/4"

16 3/4"

19 1/16"

20 1/16"

1 5/16"

FILTER ACCESS PANEL


22" MIN. DISTANCE
BOTH SIDE

20 1/16"

16 3/4" 16 1/4"
13 3/4"

1 5/16"

1 5/8"

SEE NOTES 2,3,4

1 5/8"

3 5/8"

3 5/8"

LIQUID LINES
SEE NOTES 2,3,4
1 3/16"

45 1/8"

(4) - HOLE FOR HORIZONTAL


SUSPENSION
SUPPLY OPENING
(4) HOLE FOR
HORIZONTAL
SUSPENSION

6 3/4"

BOTTOM RETURN
SIDE RETURN
54 1/16"

36 7/8"

FILTER
10 7/16"

BOTTOM RETURN
SUPPLY VERTICAL RETURN HORIZONTAL /
RETURN VERTICAL

104

SIDE RETURN
SUPPLY HORIZONTAL RETURN VERTICAL /
RETURN HORIZONTAL

SS-PRC028-EN

Dimensional Data

Figure 33. 10 Ton Air Handler, Single Circuit


NOTES:
1 PANEL DEPTH 1/2" (TYP.ALL PANELS).
2. REMOVABLE DRAIN PAN AND ATTACHED DRAIN CONNECTION MAY BE INSTALLED ON END
OF UNIT IN EITHER THE VERTICAL OR HORIZONTAL CONFIGURATION, PLASTIC DRAIN PAN
ACCESS PLATE ON THE END OF UNIT OPPOSITE DRAIN CONNECTION MUST BE REMOVED TO
SLIDE DRAIN PAN OUT OF UNIT FOR CLEANING. ACCESS PLATE MUST BE RE-INSTALLED AFTER
SLIDING DRAIN PAN BACK INTO UNIT.
3. IF PERIODIC DRAIN PAN CLEANING IS REQUIRED, ALLOW ROOM FOR PARTIAL REMOVAL OF
DRAIN PAN CONNECTION AT END OF UNIT.
4. 1" FEMALE SCHED. 40 PVC PIPE DRAIN CONNECTION VERTICAL CONFIGURATION.
5. 1" FEMALE SCHED. 40 PVC PIPE DRAIN CONNECTION HORIZONTAL CONFIGURATION.

25
15 15/16"

3/4"

SUPPLY
OPENING

22 1/4"

18 15/16"
HEATER CONTROL
AND SINGLE POWER
ENTRY WIRES
20 5/16"
16 5/16"

HEATER
VENTILATION

SIDE RETURN

15 15/16"

2 1/4"

1 13/16"

1 11/16"

6 13/16"

BOTTOM RETURN

16 7/8"

2 3/4"

58"

58"

2 3/4"

CONTROL WIRING
3 1/2"

LINE VOLTAGE

8 7/8"

CONTROL BOX
ACCESS PANEL

16 1/16"

DRAIN CONNECTION
FOR HORIZONTAL
(SEE NOTE 2,3,5)

COPPER LIQUID LINE


FIELD CONNECTION

REMOTE BULB TXV


COPPER SUCTION LINE
FIELD CONNECTION

SUCTION LINE
1 3/16"

22 7/8"

16 11/16"

FILTER ACCESS PANEL


22" MIN. DISTANCE
BOTH SIDE

17 3/8"

20"

17 3/8"

16 11/16"

1 11/16"

3 5/8"

3 5/8"

1 11/16"

SEE NOTES
2,3,4

LIQUID LINES
SEE NOTES 2,3,4
63 1/2"
1 3/16"

(4) - HOLEFOR
HORIZONTAL
SUSPENSION

61 1/8"

SUPPLY OPENING

(4) HOLE FOR


HORIZONTAL
SUSPENSION

BOTTOM RETURN

6 3/4"
SIDE RETURN

54 1/16"

36 7/8"
FILTER
BOTTOM RETURN
10 7/16"

SS-PRC028-EN

SUPPLY VERTICAL RETURN HORIZONTAL /


RETURN VERTICAL

SIDE RETURN
SUPPLY HORIZONTAL RETURN VERTICAL /
RETURN HORIZONTAL

105

Dimensional Data

Figure 34. 10 Ton Air Handler, Dual Circuit


NOTES:
1 PANEL DEPTH 1/2" (TYP.ALL PANELS).
2. REMOVABLE DRAIN PAN AND ATTACHED DRAIN CONNECTION MAY BE INSTALLED ON END
OF UNIT IN EITHER THE VERTICAL OR HORIZONTAL CONFIGURATION, PLASTIC DRAIN PAN
ACCESS PLATE ON THE END OF UNIT OPPOSITE DRAIN CONNECTION MUST BE REMOVED TO
SLIDE DRAIN PAN OUT OF UNIT FOR CLEANING. ACCESS PLATE MUST BE RE-INSTALLED AFTER
SLIDING DRAIN PAN BACK INTO UNIT.
3. IF PERIODIC DRAIN PAN CLEANING IS REQUIRED, ALLOW ROOM FOR PARTIAL REMOVAL OF
DRAIN PAN CONNECTION AT END OF UNIT.
4. 1" FEMALE SCHED. 40 PVC PIPE DRAIN CONNECTION VERTICAL CONFIGURATION.
5. 1" FEMALE SCHED. 40 PVC PIPE DRAIN CONNECTION HORIZONTAL CONFIGURATION.

25
15 15/16"

3/4"

SUPPLY
OPENING

22 1/4"

18 15/16" 63 1/2"
HEATER CONTROL
AND SINGLE
POWER ENTRY WIRES
16 5/16"

HEATER
VENTILATION

20 5/16"

2 1/4"

1 13/16"

1 11/16"

6 13/16"

BOTTOM RETURN

16 7/8"

SIDE RETURN

15 15/16"

2 3/4"

58"

58"

2 3/4"

CONTROL WIRING
3 1/2"

LINE VOLTAGE

8 7/8"

CONTROL BOX
ACCESS PANEL

16 1/16"

DRAIN CONNECTION
FOR HORIZONTAL
(SEE NOTE 2,3,5)

COPPER LIQUID LINE


FIELD CONNECTION

(2) REMOTE BULB TXV


COPPER SUCTION LINE
FIELD CONNECTION

SUCTION LINE
1 3/16"

22 7/8"
11" 13 11/16"
FILTER ACCESS PANEL
22" MIN. DISTANCE
BOTH SIDE

16 1/4"

16 11/16"

19"

20"

20 1/16"

16 3/4" 16 1/4"

13 3/4"

1 5/16"

1 5/16"

1 5/8"

1 5/8"

3 5/8"

3 5/8"

SEE NOTES
2,3,4

LIQUID LINES
SEE NOTES 2,3,4
(4) - HOLE FOR HORIZONTAL
SUSPENSION
1 3/16"

61 1/8"

SUPPLY OPENING

6 3/4"

(4) HOLE FOR


HORIZONTAL
SUSPENSION

BOTTOM RETURN
SIDE RETURN

54 1/16"

36 7/8"
FILTER
BOTTOM RETURN
10 7/16"

106

SUPPLY VERTICAL RETURN HORIZONTAL /


RETURN VERTICAL

SIDE RETURN
SUPPLY HORIZONTAL RETURN VERTICAL /
RETURN HORIZONTAL

SS-PRC028-EN

Dimensional Data

Figure 35. 12 -15 Ton Air Handler, Dual Circuit


28 1/8
16"

3 1/16"
NOTES:
1 PANEL DEPTH 1/2" (TYP.ALL PANELS).
2. REMOVABLE DRAIN PAN AND ATTACHED DRAIN CONNECTION MAY BE INSTALLED ON END
OF UNIT IN EITHER THE VERTICAL OR HORIZONTAL CONFIGURATION, PLASTIC DRAIN PAN
ACCESS PLATE ON THE END OF UNIT OPPOSITE DRAIN CONNECTION MUST BE REMOVED TO
SLIDE DRAIN PAN OUT OF UNIT FOR CLEANING. ACCESS PLATE MUST BE RE-INSTALLED AFTER SLIDING
DRAIN PAN BACK INTO UNIT.
3. IF PERIODIC DRAIN PAN CLEANING IS REQUIRED, ALLOW ROOM FOR PARTIAL REMOVAL OF
DRAIN PAN CONNECTION AT END OF UNIT.
4. 1" FEMALE SCHED. 40 PVC PIPE DRAIN CONNECTION VERTICAL CONFIGURATION.
5. 1" FEMALE SCHED. 40 PVC PIPE DRAIN CONNECTION HORIZONTAL CONFIGURATION.

14 1/8"

18 11/16"
SUPPLY
OPENING

13 7/8"

18 11/16"
17 7/8"
HEATER CONTROL
AND SINGLE POWER
ENTRY WIRES

LINE VOLTAGE

19 1/2"

SIDE RETURN

BOTTOM RETURN

BOTTOM RETURN

3 7/16"

3 5/16"

12 1/8"

2 3/4"

4 5/16"

CONTROL WIRING

SIDE RETURN

74 1/8"

2 3/4"

74 1/8"

4 1/4"
12 13/16"

20"
CONTROL BOX
ACCESS PANEL

COPPER LIQUID LINE


FIELD CONNECTION

DRAIN CONNECTION
FOR HORIZONTAL
(SEE NOTE 2,3,5)

(2) REMOTE BULB TXV


COPPER SUCTION LINE
FIELD CONNECTION

SUCTION LINE

1 1/4"
25 1/8"
12"

FILTER ACCESS PANEL


22" MIN. DISTANCE
BOTH SIDE

15 13/16" 18 5/16" 18 11/16"

22"

21 1/2"

21 1/2"

18 11/16"

18 3/8"

15 13/16"

1 5/16"

2"

2 1/8"
2 7/16"
4 1/4"

2 5/16"

SEE NOTES
2,3,4

4 1/8"

LIQUID LINES
(4) - HOLE FOR HORIZONTAL
SUSPENSION

SEE NOTES 2,3,4

(4) HOLE FOR


HORIZONTAL
SUSPENSION

79 5/8"
SUPPLY OPENING
1 3/16"

77 3/16"
BOTTOM RETURN

9 5/8"

SIDE RETURN

69 1/16"

48"

FILTER

BOTTOM RETURN

11 7/16"

SS-PRC028-EN

SUPPLY VERTICAL RETURN HORIZONTAL /


RETURN VERTICAL

SIDE RETURN
SUPPLY HORIZONTAL RETURN VERTICAL /
RETURN HORIZONTAL

107

Dimensional Data

Figure 36. 20 Ton Air Handler, Dual Circuit


31 1/8"
NOTES:
1 PANEL DEPTH 1/2" (TYP.ALL PANELS).
2. REMOVABLE DRAIN PAN AND ATTACHED DRAIN CONNECTION MAY BE INSTALLED ON END
OF UNIT IN EITHER THE VERTICAL OR HORIZONTAL CONFIGURATION, PLASTIC DRAIN PAN
ACCESS PLATE ON THE END OF UNIT OPPOSITE DRAIN CONNECTION MUST BE REMOVED TO
SLIDE DRAIN PAN OUT OF UNIT CLEANING. ACCESS PLATE MUST BE RE-INSTALLED AFTER
SLIDING DRAIN PAN BACK INTO UNIT.
3. IF PERIODIC DRAIN PAN CLEANING IS REQUIRED, ALLOW ROOM FOR PARTIAL REMOVAL OF
DRAIN PAN CONNECTION AT END OF UNIT.
4. 1" FEMALE SCHED. 40 PVC PIPE DRAIN CONNECTION VERTICAL CONFIGURATION.
5. 1" FEMALE SCHED. 40 PVC PIPE DRAIN CONNECTION HORIZONTAL CONFIGURATION.

16"
5 1/8"

20 11/16"

18 11/16"
SUPPLY
OPENING

13 7/8"

18 11/16"
HEATER CONTROL
AND SINGLE POWER
ENTRY WIRES

20 15/16"

SIDE RETURN

BOTTOM RETURN

20 15/16"

SIDE RETURN

BOTTOM RETURN

18 5/8"
2 15/16"

3"
4 3/4"

CONTROL WIRING

4 3/4"

83 1/8"

83 1/8"

LINE VOLTAGE

12 13/16"
CONTROL BOX
ACCESS PANEL

20"
COPPER LIQUID LINE
FIELD CONNECTION

DRAIN CONNECTION
FOR HORIZONTAL
(SEE NOTE 2,3,5)

REMOTE BULB TXV

COPPER SUCTION LINE


FIELD CONNECTION

SUCTION LINE

1 3/16"
28 1/2"
12 7/8"
FILTER ACCESS PANEL
22" MIN. DISTANCE
BOTH SIDE
LIQUID LINES
SEE NOTES 2,3,4

21 3/8" 21 13/16" 25 1/2"


15 7/8" 18 3/8" 19 1/8"
25 1/2" 21 13/16" 19 1/8"

18 3/8" 15 7/8"
SEE NOTES
2,3,4

1 11/16"
1 15/16"

1 9/16"

3 3/8"

1 7/8"

4"

3 1/4"

(4) - HOLE FOR HORIZONTAL


SUSPENSION

3 7/8"

92 9/16"
1 11/16"

89 3/16"

9 5/8"

50 13/16"

SIDE RETURN

SIDE RETURN
FILTER

71 7/8"
BOTTOM RETURN

11 7/16"

108

(4) HOLE FOR


HORIZONTAL
SUSPENSION

SUPPLY OPENING

BOTTOM RETURN
SUPPLY VERTICAL RETURN HORIZONTAL /
RETURN VERTICAL

SUPPLY HORIZONTAL RETURN VERTICAL /


RETURN HORIZONTAL

SS-PRC028-EN

Dimensional Data

Figure 37. 5-20 Tons Rubber Isolator Accessory Dimensions

Table 58. Rubber Isolator Dimensions in.


Model No.

BAYISLT004
BAYISLT005
BAYISLT009
BAYISLT010
BAYISLT013
BAYISLT014
BAYISLT015(a)
BAYISLT012
BAYISLT015(a)
BAYISLT016

3-1/8

1-3/4

1-1/4

1-1/4

3/8

2-3/8

3/8

1/4

3-7/8

2-3/8

1-3/4

1-3/4

3/8

3/8

1/4

2-1/4

1-3/8

3/4

3/8

1/2

2-1/4

4-1/2

1-7/8

1/4

5/8

3/4

(a) BAYISLT015 contains quantity 2 of the 2 1/4 x 2 x 3 isolators and quantity 3 of the 3 x 2 1/4 x 4 1/2 isolators.

Figure 38. 5-20 Tons Spring Isolator Accessory Dimensions in inches (mm)

SS-PRC028-EN

109

Dimensional Data

Figure 39. Electric Heater Accessory for 10 Ton and Under Air Handlers. All dimensions are in inches.

Figure 40. Electric Heater Accessory for over 10 Ton Air Handlers. All dimensions are in inches.

110

SS-PRC028-EN

Dimensional Data

Figure 41. Hot Water Coil Accessory. All dimensions are in inches (millimeters).

Table 59. Hot Water Coil Dimensions in.


Tons

Model No.

BAYWATR017

BAYWATR018

10

BAYWATR019

12

BAYWATR020

15

BAYWATR020

20

BAYWATR021

Q(a)

22 5/8 13 11/32

14

14

26

12

47 5/8 25 5/8 15 19/32

10 7/8 17 1/8

14

30

18

8 7/8

63 5/8 25 5/8 15 19/32

11 7/8 17 1/8

16

36

18

13 7/8 8 3/32 10 3/8 2 7/8 7 7/8 2 1/2 NPTI

38

4 11/32 8 1/4 2 7/8 10 1/2

2 NPT

8 3/32 10 3/8 2 7/8 7 7/8 2 1/2 NPTI

79 5/8

29

14 7/16

15 1/8 19 3/4

16

51

18

14 1/4 6 15/16 9 1/2 1 7/8

2 1/2 NPTI

79 5/8

29

14 7/16

15 1/8 19 3/4

16

51

18

14 1/4 6 15/16 9 1/2 1 7/8

2 1/2 NPTI

16 3/8

14 3/4 22 1/2

18

64

18

14 1/4

2 1/2 NPTI

92 5/8 31 1/8

8 7/8

9 1/2 3 3/4

(a) Note internal vs. external pipe threads

SS-PRC028-EN

111

Dimensional Data

Figure 42. Steam Coil Accessory. All dimensions are in inches.

Table 60. Air Handler Dimensions in.


Tons

Model No.

BAYWATR012

BAYWATR013

10

BAYWATR014

12

BAYWATR015

15

BAYWATR015

20

BAYWATR016

112

38

22 5/8

13 3/4

14 1/16

14

10 3/8 11 3/8

1 1/2

26

12

47 5/8 25 11/16 19 3/4

10 7/8 17 1/8

14

63 5/8 25 11/16 19 3/4

11 7/8 17 1/8

79 5/8

29

24 7/8

15

79 5/8

29

24 7/8

15

92 5/8

31 1/8

25 7/8

13 3/8 11 3/8 2 1/2

30

18

8 7/8 2 7/8 9 3/4

16

13 3/8 11 1/8 2 1/2

36

18

13 7/8 2 7/8 9 3/4

19 3/4

16

18 1/2 11 1/8 2 1/2

51

18

14 1/8 1 7/8 9 3/4

19 3/4

16

18 1/2 11 1/8 2 1/2

51

18

14 1/8 1 7/8 9 3/4

14 3/4 22 1/2

18

19 1/2

64

18

14 1/8 3 3/4 10 7/8

12

2 1/2

2 7/8 9 3/4

SS-PRC028-EN

Dimensional Data

Figure 43. Discharge Plenum and Grille Accessory

Table 61. Discharge Plenum and Grille Dimensions in. No Heat


Tons

Model No.

BAYPLNM015

37 15/16

21 15/16

28

BAYPLNM016

47 1/2

25

28

10

BAYPLNM017

63 1/2

25

28

Table 62. Hydronic Discharge Plenum and Grille Dimensions in.


Tons

Model No.

BAYPLNM020

37 7/8

21 7/8

14 3/4

BAYPLNM021

47 1/2

25

14 3/4

10

BAYPLNM022

63 1/2

25

14 3/4

12

BAYPLNM018(a)

79 1/2

27 11/16

22

15

BAYPLNM018(a)

79 1/2

27 11/16

22

20

BAYPLNM019(a)

92 1/2

30 7/16

24

(a) For use with hydronic heat or no heat.

SS-PRC028-EN

113

Dimensional Data

Figure 44. Discharge Plenum and Grille Accessory

C
A

Table 63. Discharge Plenum and Grille Dimensions (in.). For use with Electric Heat.
Tons

Model No.

BAYPLNM030

37 15/16

22 7/8

29

BAYPLNM031

47 1/2

25 7/8

29

10

BAYPLNM032

63 1/2

25 7/8

29

12

BAYPLNM033

79 1/2

29 3/8

35

15

BAYPLNM033

79 1/2

29 3/8

35

20

BAYPLNM034

92 1/2

31 3/8

35

Figure 45. Subbase Accessory

Table 64. Subbase Dimensions (in.)

114

Tons

Model No.

BAYBASE009

38

22.63

BAYBASE010

47 1/2

25.51

10

BAYBASE011

63 1/2

25.52

12

BAYBASE012

79 1/2

29.04

15

BAYBASE012

79 1/2

29.04

20

BAYBASE013

92 1/2

31.14

SS-PRC028-EN

Weights
Table 65. TTA Unit and Corner Weights lbs (60 Hz)
Corner Weights

Tons

Model No.

Shipping
Max (lbs)

Net Max (lbs)

TTA073D

365

300

85

90

44

81

TTA090D

363

298

84

89

44

81

TTA120D

467

395

133

103

70

89

TTA120E

510

438

137

127

88

86

TTA120F

509

438

129

140

83

86

10

12
15

20

TTA150E

543

468

130

151

79

108

TTA180E

850

723

207

204

151

161

TTA180F

852

725

196

208

153

168

TTA240E

970

837

262

240

164

171

TTA240F

966

835

257

249

153

176

Figure 46. TTA073, 090, 120, 150

Figure 47. TTA180, 240

Table 66. TWE Unit and Corner Weights - lbs (60 Hz)
Corner Weights - Vertical
Shipping Max (kg) Net Max (kg)

Corner Weights - Horizontal

Tons

Model No.

TWE061D/E

TWE090D/E

360

323

67

99

75

82

56

92

87

88

10

TWE120D/E

429

393

77

121

110

85

79

118

77

119

263

232

55

71

51

55

54

67

50

61

12

TWE150E

730

676

168

192

181

135

196

164

145

171

15

TWE180E

729

675

167

192

181

135

196

163

145

171

20

TWE240E

891

818

258

168

161

231

256

181

146

235

SS-PRC028-EN

115

Weights

Figure 48. Vertical - TWE061, 090, 120

Figure 49. Vertical - TWE150, 180, 240

Figure 50. Horizontal - TWE061, 090, 120

Figure 51. Horizontal - TWE150, 180, 240

Table 67. Accessory Weights (net lbs.) - 60 Hz


Unit
Used With Hot Water Steam
Tons
Coil
Coil

Discharge
Plenum
and
Grille(a)

Discharge Discharge
Return Electric
Plenum
Plenum
and
and
Air
Heat
Oversized
Grille Min/Max Subbase
Motor
Grille(b)
Grille(c)

RIS
Isolator
Floor
Mount

86

94

63

58

115

32/43

14.4

31

116

131

78

73

160

27/45

19.4

48

10

165

148

97

92

195

27/45

23.5

50

12

211

234

230

235

10

79/100

28.4

80

15

211

234

230

235

10

79/100

28.4

80

20

242

261

145

265

12

79/100

31.7

88

Continued
RIS
Unit
Isolator
Used With Suspended
Tons
Mount

Steel Spring
Isolator
Floor Mount

Steel
Spring
Isolator
Suspended
Mount

12

12

10

12

12

12

15

12

20

12

(a) For use with Hydronic Heat.


(b) For use when no heat is supplied.
(c) For use with electric heat.

116

SS-PRC028-EN

Weights

Table 68.

Accessory Weights (60Hz)

Control
Unit Model # Transformer

SS-PRC028-EN

Hail Guard

Sensors

Modulating
Low
Ambient

On/Off
Low Ambient

TTA073

20

23

TTA090

20

23

TTA120

27

23

TTA150

30

23

TTA180

53

23 (req. qty 2)

1 (req. qty 2)

TTA240

53

42 (req. qty 2)

1 (req. qty. 2)

117

Mechanical Specifications
TTA Condensing Units
General

Weatherproofed Steel Mounting/Lifting Rails

Hermetic Scroll Compressors

Plate Fin Condenser Coils

Fans and Motors

Standard Operating Range 50-125F (Min. 0F with Low Ambient Accy)

Nitrogen Holding Charge

Certified and Rated in Accordance with AHRI and DOE Standards

Certified to UL 1995

Casing

Zinc Coated, Heavy Gauge, Galvanized Steel

Weather Resistant Baked Enamel Finish

Meets 672 hr Salt Spray Test

Removable Single Side Maintenance Access Panels

Lifting Handles in Maintenance Access Panels

Unit Base Provisions for Forklift and/or Crane Lifting

Refrigeration System - Single Compressor (TTA073D, TTA090D, TTA120D)

Single Refrigeration Circuit with Integral Subcooling Circuit.

Single Direct Drive Hermetic Scroll Compressor

Suction Gas-Cooled Motor w/ 10% Voltage Utilization Range of Unit Nameplate Voltage

Crankcase Heater

Internal Temperature and Current Sensitive Motor Overloads

No Compressor Suction and/or Discharge Valves (Reduced Vibration/Sound)

Factory Installed Liquid Line Filter Drier

Phase Loss/Reverse Rotation Monitor

Liquid Line Service Valve (with gauge port)

Suction Line Service Valve (with gauge port)

External High Pressure Cutout Device

External Low Pressure Cutout Device

Evaporator Defrost Control

Loss of Charge Protection (Discharge Temperature Limit)

Refrigeration System - Dual Compressor (TTA120E, TTA150E, TTA180E,


TTA240E)

118

Two (2) Separate and Independent Refrigerant Circuits

Each Refrigeration Circuit Equipped with Integral Subcooling Circuit.

Two (2) Direct Drive Hermetic Scroll Compressor

Suction Gas-Cooled Motors w/ 10% Voltage Utilization Range of Unit Nameplate Voltage

Crankcase Heaters
SS-PRC028-EN

Mechanical Specifications

Internal Temperature and Current Sensitive Motor Overloads

Factory Installed Liquid Line Filter Driers

Phase Loss/Reverse Rotation Monitor

Liquid Line Service Valves (with gauge port)

Suction Line Service Valves (with gauge port)

No Compressor Suction and/or Discharge Valves (Reduced Vibration/Sound)

External High Pressure Cutout Devices

External Low Pressure Cutout Devices

Evaporator Defrost Control

Loss of Charge Protection (Discharge Temperature Limit)

Refrigeration System - Dual Manifolded Compressors (TTA120F, TTA180F,


TTA240F)

Single Refrigerant Circuit with Integral Subcooling Circuit.

Two (2) Direct Drive Hermetic Scroll Compressor

Suction Gas-Cooled Motors w/ 10% Voltage Utilization Range of Unit Nameplate Voltage

Crankcase Heaters

Internal Temperature and Current Sensitive Motor Overloads

No Compressor Suction and/or Discharge Valves (Reduced Vibration/Sound)

Factory Installed Liquid Line Filter Drier

Phase Loss/Reverse Rotation Monitor

Liquid Line Service Valve (with gauge port)

Suction Line Service Valve (with gauge port)

External High Pressure Cutout Devices

External Low Pressure Cutout Devices

Evaporator Defrost Control

Loss of Charge Protection (Discharge Line Thermostats)

Condenser Coil

3/8 Internally Enhanced Copper Tube Mechanically Bonded to Lanced Aluminum Plate Fins

Factory Pressure and Leak Tested to 660 psig.

Perforated Steel Hail Guards Available (Factory Installed Option or Field Installed Accessory)

Condenser Fan

26" or 28" Propeller Fan(s)

Direct Drive

Statically and Dynamically Balanced

Condenser Motor(s)

Permanently Lubricated Totally Enclosed or Open Construction

Built-In Current and Thermal Overloads

Ball or Sleeve Bearing Type

Controls

SS-PRC028-EN

Choice of Electro-mechanical or Microprocessor


119

Mechanical Specifications

Completely Internally Wired

Numbered and Colored Wires

Contactor Pressure Lugs or Terminal Block

Unit External Mounting Location for Disconnect Device

Single Point Power Entry

Factory Installed Options


Hail Guards

Condenser Coil Protection from Hail, Vandals, Etc.

Perforated, Painted Galvanized Steel

Factory or Field Installed

Black Epoxy Coated Condenser Coil

Thermoset Vinyl Coating

Bonded to Aluminum Fin Stock (Prior to Fin-Stamping Process)

Economical Protectant in Mildly Corrosive Environments

Lon Talk Communication Interface

Factory or Field Installed

Communications Board

Allows Unit Communication as a Tracer LCI-R Device

Allows Unit Communication with Generic LonTalk Network Building Automation Controls

Controls: Electro-Mechanical

24V Control Circuit

Control Transformer

Thermostat Compatible

Anti-Short Cycle Timer

Controls: Microprocessor

Centralized Processor

Indoor and Outdoor Temperature Sensors Drive Algorithms Making Decisions for All Heating,
Cooling, and Ventilation

Integrated Anti-Short Cycle Timer

Integrated Time Delay Between Compressors

Field Installed Accessories


Low Ambient (Fan ON/OFF)

Provides Unit Cooling Operation to Outdoor Ambient of 0F

Low Cost Solution

Liquid Line Temperature Controls Condenser Fan Operation

1 Kit Per Condenser Fan Required

Low Ambient (Modulating)

120

Provides Unit Cooling Operation to Outdoor Ambient of 0F

Wave-Chopper
SS-PRC028-EN

Mechanical Specifications

Discharge Line Pressure Controls Condenser Fan Operation

1 Kit Per Condenser Fan Required

Vibration Isolators

Neoprene-In-Shear or Spring Flex Choice

Reduce Vibration Transmission to Building Structures, Equipment, and Adjacent Spaces

Reduce Noise Transmission to Building Structures, Equipment, and Adjacent Spaces

Hot Gas Bypass

Provides Capacity Modulation Solution

Time Delay Relay

Electro-Mechanical Units Only

Prevent Simultaneous Starting of Both Compressors in Dual Compressor Units

24V

4 Minute Timing Period

Zone Sensor

Interfaces with Microprocessor Units

Manual or Automatic Programmable

System Malfunction Lights

Remote Sensor Options

Thermostat

1H/1C Available

2H/1C Available

Manual or Automatic Changeover Available

Automatic Programmable Electronic with Night Setback Available

Lon Talk Communication Interface

SS-PRC028-EN

Factory or Field Installed

Communications Board

Allows Unit Communication as a Tracer LCI-R Device

Allows Unit Communication with Generic LonTalk Network Building Automation Controls

121

Mechanical Specifications

TWE Air Handlers


General

Completely Factory Assembled

Convertible for Horizontal or Vertical Configuration

Convertible for Cooling Only or Heat Pump Application

Convertible for Left or Right External Connections (Refrigerant and/or Electrical)

Convertible for Front or Bottom Air Return

Nitrogen Holding Charge

Certified to UL 1995 for Indoor Blower Coil Units

Casing

Zinc Coated, Heavy Gauge, Galvanized Steel

Weather Resistant Baked Enamel Finish

Access Panels with Captive Screws

Completely Insulated with Foil Faced, Cleanable, Fire Retardant, Permanent,


Odorless Glass Fiber Material

Captured or Sealed Insulation Edges

Electrical Connection Bushings or Plugs

Refrigerant Connection Bushings or Plugs

Withstand Elevated Internal Static Pressure

Refrigeration System

Single or Dual Circuit

Distributor(s)

Thermal Expansion Valves (TXVs)

Evaporator Coil

3/8 Internally Enhanced Copper Tube Mechanically Bonded to Lanced Aluminum Plate Fins

Factory Pressure and Leak Tested to 449 psig.

Draw-Through Airflow

Dual Circuits Are Interlaced/Intertwined

Double Sloped, Removable, Cleanable, Composite Drain Pan

Four Drain Pan Positions

Indoor Fan

122

Double Inlet, Double Width, Forward Curved, Centrifugal Type Fan

Dual Fans On 12.5-20T Air Handlers

Adjustable Belt Drive

Permanently Lubricated Bearings

SS-PRC028-EN

Mechanical Specifications

Indoor Motor

Adjustable Motor Sheaves

Thermal Overload Protection

Permanently Lubricated Bearings

Meet Energy Policy of 1992 (EPACT)

Optional Over Sized Motors for High Static Applications

Controls

Completely Internally Wired

Numbered and Colored Wires

Magnetic Indoor Fan Contactor

Low Voltage Terminal Strip

Single Point Power Entry

Evaporator Defrost Control

Filters

Access From Side Coil Panels

Filters Slide on Rack

One Inch (1"), Throw-Away Filters on 5-10 Ton Units

Filter Rack Convertible to Two Inch (2") Capability on 5-10 Ton Units

Two Inch (2"), Throw-Away Filters on 12.5-20 Ton Units

Field Installed Accessories


Electric Heaters

Heavy Duty Nickel Chromium Elements

ETL Approved

Installs Directly On Fan Discharge

One or Two Stage Control (Dependent Upon Capacity)

Single Point Power Entry

Terminal Strip Connections

460V Heaters
Internally Wye Connected
Automatic Line Break High Limit Controls

230V Heaters
Internally Delta Connected
Automatic Reset of High Limit Controls Through Pilot Duty with Secondary Backup Fuse
Links

Hydronic Heat Coils

SS-PRC028-EN

One Row Steam

Two Row Hot Water

Installs Directly On Fan Discharge

Heavy Gauge Sheet Metal Casing Matches Air Handler

Convertible for Horizontal or Vertical Configurations


123

Mechanical Specifications

Discharge Plenums and Grilles

Vertical, Free Discharge Applications

Heavy Gauge Sheet Metal Casing Matches Air Handler

Satin Finished, 4-Way Adjustable Louver Grilles

Return Air Grilles

Vertical, Free Discharge Applications

Satin Finished, Non-Adjustable Louver Grilles

Replaces Front Lower Access Panel

Mounting Sub-Base

Vertical Floor Mount Configuration Requirement

Heavy Gauge Sheet Metal Casing Matches Air Handler

Provides Additional Clearance for Condensate Drain Trapping

Required When Isolators Are Used

Vibration Isolators

Neoprene-In-Shear or Spring Flex Choice

Floor or Suspended Applications

Reduce Vibration Transmission to Building Structures, Equipment, and Adjacent Spaces

Reduce Noise Transmission to Building Structures, Equipment, and Adjacent Spaces

Over Size Motors

124

High Static Applications

Motor, Sheaves, Belt Included

SS-PRC028-EN

Literature Order Number

SS-PRC028-EN

Date

September 2009

Supersedes

SS-PRC028-EN (July 2009)

www.trane.com
For more information, contact your local Trane
office or e-mail us at [email protected]

Trane has a policy of continuous product and product data improvement and reserves the right to
change design and specifications without notice. Only qualified technicians should perform the
installation and servicing of equipment referred to in this literature.

You might also like