Hot Standby Router Protocol Features and Functonality From Cisco

Download as pdf or txt
Download as pdf or txt
You are on page 1of 14

Hot Standby Router Protocol Features and

Functionality
Document ID: 9234
Contents
Introduction
Prerequisites
Requirements
Components Used
Conventions
HSRP Background and Operations
Dynamic Router Discovery Mechanisms
HSRP Operation
HSRP Addressing
Cisco IOS Release and HSRP Functionality Matrix
Cisco IOS Boot Images and HSRP Functionality
HSRP Features
Preemption
Interface Tracking
Use BurnedIn Address
Multiple HSRP Groups
Configurable MAC Address
Syslog Support
HSRP Debugging
Enhanced HSRP Debugging
Authentication
IP Redundancy
SNMP Management Information Base
HSRP Support for Multiprotocol Label Switching Virtual Private Networks
HSRP Support for ICMP Redirects
HSRP Interface and Media Support
Ethernet
Token Ring
802.1Q
ISL
FDDI
MAC Refresh
Bridge Group Virtual Interface
Subinterfaces
Related Information
Introduction
This document describes the features and functionality of Hot Standby Router Protocol (HSRP).
Prerequisites
Requirements
There are no specific requirements for this document.
Components Used
This document is not restricted to specific software and hardware versions.
Conventions
For more information on document conventions, refer to Cisco Technical Tips Conventions.
HSRP Background and Operations
One way to achieve near100 percent network uptime is to use HSRP, which provides network redundancy
for IP networks, ensuring that user traffic immediately and transparently recovers from first hop failures in
network edge devices or access circuits.
By sharing an IP address and a MAC (Layer 2) address, two or more routers can act as a single "virtual"
router. The members of the virtual router group continually exchange status messages. This way, one router
can assume the routing responsibility of another, should it go out of commission for either planned or
unplanned reasons. Hosts continue to forward IP packets to a consistent IP and MAC address, and the
changeover of devices doing the routing is transparent.
Dynamic Router Discovery Mechanisms
Below are descriptions of dynamic router discovery mechanisms that are available to hosts. Many of these
mechanisms don't provide the network resiliency required by network administrators. This may be because the
protocol wasn't initially intended to provide network resiliency or because it isn't feasible for every host on a
network to be running the protocol. In addition to what is listed below, it is important to note that many hosts
only allow you to configure a defaultgateway.
Proxy Address Resolution Protocol
Some IP hosts use proxy Address Resolution Protocol (ARP) to select a router. When a host runs proxy ARP,
it sends an ARP request for the IP address of the remote host it wants to contact. A router, Router A, on the
network replies on behalf of the remote host and provides its own MAC address. With proxy ARP, the host
behaves as if the remote host were connected to the same segment of the network. If Router A fails, the host
continues to send packets destined for the remote host to the MAC address of Router A even though those
packets have nowhere to go and are lost. You can either wait for ARP to acquire the MAC address of another
router, Router B, on the local segment by sending another ARP request, or reboot the host to force it to send
an ARP request. In either case, for a significant period of time, the host can't communicate with the remote
host, even though the routing protocol has converged, and Router B is prepared to transfer packets that would
otherwise go through Router A.
Dynamic Routing Protocol
Some IP hosts run (or snoop) a dynamic routing protocol such as the Routing Information Protocol (RIP) or
Open Shortes Path First (OSPF) to discover routers. The drawback of using RIP is that it is slow to adapt to
changes in the topology. Running a dynamic routing protocol on every host may not be feasible for a number
of reasons, including administrative overhead, processing overhead, security issues, or lack of a protocol
implementation for some platforms.
ICMP Router Discovery Protocol
Some newer IP hosts use ICMP Router Discovery Protocol (IRDP) (RFC 1256 ) to find a new router when
a route becomes unavailable. A host that runs IRDP listens for hello multicast messages from its configured
router and uses an alternate router when it no longer receives those hello messages. The default timer values
of IRDP mean that it's not suitable for detection of failure of the first hop. The default advertisement rate is
once every 7 to 10 minutes, and the default lifetime is 30 minutes.
Dynamic Host Configuration Protocol
Dynamic Host Configuration Protocol (DHCP) (RFC 1531 ) provides a mechanism for passing
configuration information to hosts on a TCP/IP network. A host that runs a DHCP client requests
configuration information from a DHCP server when it boots onto the network. This configuration
information typically comprises an IP address and a default gateway. There is no mechanism for switching to
an alternative router if the default gateway fails.
HSRP Operation
A large class of legacy host implementations that don't support dynamic discovery are capable of configuring
a default router. Running a dynamic router discovery mechanism on every host may not be feasible for a
number of reasons, including administrative overhead, processing overhead, security issues, or lack of a
protocol implementation for some platforms. HSRP provides failover services to these hosts.
Using HSRP, a set of routers works in concert to present the illusion of a single virtual router to the hosts on
the LAN. This set is known as an HSRP group or a standby group. A single router elected from the group is
responsible for forwarding the packets that hosts send to the virtual router. This router is known as the Active
router. Another router is elected as the Standby router. In the event that the Active router fails, the Standby
assumes the packetforwarding duties of the Active router. Although an arbitrary number of routers may run
HSRP, only the Active router forwards the packets sent to the virtual router.
To minimize network traffic, only the Active and Standby routers send periodic HSRP messages once the
protocol has completed the election process. If the Active router fails, the Standby router takes over as the
Active router. If the Standby router fails or becomes the Active router, then another router is elected as the
Standby router.
On a particular LAN, multiple hot standby groups may coexist and overlap. Each standby group emulates a
single virtual router. The individual routers may participate in multiple groups. In this case, the router
maintains separate state and timers for each group.
Each standby group has a single, wellknown MAC address, as well as an IP address.
HSRP Addressing
In most cases when you configure routers to be part of an HSRP group, they listen for the HSRP MAC
address for that group as well as their own burnedin MAC address. The exception is routers whose Ethernet
controllers only recognize a single MAC address (for example, the Lance controller on the Cisco 2500 and
Cisco 4500 routers). These routers use the HSRP MAC address when they are the Active router, and their
burnedin address when they are not.
HSRP uses the following MAC address on all media except Token Ring:
0000.0c07.ac** (where ** is the HSRP group number)
Token Ring interfaces use functional addresses for the HSRP MAC address. Functional addresses are the only
general multicast mechanism available. There are a limited number of Token Ring functional addresses
available and many of them are reserved for other functions. You can use the following three addresses with
HSRP:
c000.0001.0000 (group 0)
c000.0002.0000 (group 1)
c000.0004.0000 (group 2)
Note: When HSRP runs in a multiplering sourceroute bridging (SRB) environment and the HSRP routers
reside on different rings, using the functional addresses can cause Routing Information Field (RIF) confusion.
For example, in an SRB environment, it is possible that an HSRP standby router resides on a different ring
than the active router. When this standby router becomes active, stations on the same ring as the old active
router need a new RIF in order to send packets to the new active router. However, since the standby (new
active) router is using the same functional address as the previous active router the stations are not aware that
they must send explorers for a new RIF. For this reason, the usebia command was introduced.
Cisco IOS Release and HSRP Functionality Matrix
This document shows which HSRP features are supported in which Cisco IOS Software releases. Click on a
feature to see a detailed description. An interim release number indicates in which release a feature first
appeared, or a release where the functionality of that feature changed.
Feature
10.0 10.2 10.3 11.0 11.1 11.2 11.3 12.0 12.0T 12.1 12.1T
Preemption
X X X X X X X X X X X
Multiple
Groups
(MHSRP)
X X X X X X X X X
Ethernet
802.10 SDE
X X X X X X X
Interface
Tracking
X X X X X X X
Use BIA
8.0 X X X X X X
Preempt
Delay
X X 6.1 X X X
Ethernet
LANE
X X X X X X
Token Ring
LANE
X X X X X
ISL
X X X X X
Syslog
Support
X X X X X
MAC
Refresh
Interval
1.0 X X X
SNMP MIB
3.0 X X
MHSRP and 3.4 X X
Use BIA
IP
Redundancy
3.4 X X
BVI
6.2 X X
802.1Q
8.1 X X
Enhanced
HSRP
Debugging
0.2 X
HSRP ICMP
Redirects
3
HSRP
MPLS VPNs
3
Cisco IOS Boot Images and HSRP Functionality
HSRP functionality was included in Cisco IOS boot images until the integration of Cisco bug ID CSCec16720
(registered customers only) . Cisco bug ID CSCec16720 removed HSRP from boot images with the exception
of:
c7200bootmz
c7200kbootmz
c10kebootmz
c4500bootmz
c7200bootmz
c7200kbootmz
c7400kbootmz
ubr7200bootmz
c6400rbootmz
rpmbootmz
rpmxfbootmz
rspbootmz
urmwbootmz
c5350bootmz
c5400bootmz
c7301bootmz
c5850bootmz
c4gwycbootmz
ubr910rbootmz
ubr910rbootmz
ubr925k8bootmz
c5850tbbootmz
HSRP Features
Preemption
The HSRP preemption feature enables the router with highest priority to immediately become the Active
router. Priority is determined first by the priority value that you configure, and then by the IP address. In each
case a higher value is of greater priority.
When a higher priority router preempts a lower priority router, it sends a coup message. When a lower priority
active router receives a coup message or hello message from a higher priority active router, it changes to the
speak state and sends a resign message.
Preempt Delay
The preempt delay feature allows preemption to be delayed for a configurable time period, allowing the router
to populate its routing table before becoming the active router.
Before Cisco IOS Software release 12.0(9), the delay started when the router reloaded. In Cisco IOS release
12.0(9) the delay starts when preemption is first attempted.
To configure HSRP priority and preemption, use the standby [group] [priority number] [preempt [delay
[minimum] seconds] [sync seconds]] command.
Refer to the HSRP Documentation for more information on configuring HSRP.
Interface Tracking
Interface tracking allows you to specify another interface on the router for the HSRP process to monitor in
order to alter the HSRP priority for a given group.
If the specified interface's line protocol goes down, the HSRP priority of this router is reduced, allowing
another HSRP router with higher priority can become active (if it has preemption enabled).
To configure HSRP interface tracking, use the standby [group] track interface [priority] command.
When multiple tracked interfaces are down, the priority is reduced by a cumulative amount. If you explicitly
set the decrement value, then the value is decreased by that amount if that interface is down, and decrements
are cumulative. If you do not set an explicit decrement value, then the value is decreased by 10 for each
interface that goes down, and decrements are cumulative.
The following example uses the following configuration, with the default decrement value of 10.
Note: When an HSRP group number is not specified, the default group number is group 0.
interface ethernet0
ip address 10.1.1.1 255.255.255.0
standby ip 10.1.1.3
standby priority 110
standby track serial0
standby track serial1
The HSRP behavior with this configuration is:
0 interfaces down = no decrease (priority is 110)
1 interface down = decrease by 10 (priority becomes100)
2 interfaces down = decrease by 10 (priority becomes 90)
The above HSRP behavior is true even if the decrement values are configured explicitly as below.
interface ethernet0
ip address 10.1.1.1 255.255.255.0
standby ip 10.1.1.3
standby priority 110
standby track serial0 10
standby track serial1 10
Before Cisco IOS release 12.1, if you start a router with a down interface, HSRP interface tracking regards the
interface as up.
This defect has Cisco bug ID CSCdp32289 (registered customers only) .
Use BurnedIn Address
The use burnedin address (BIA) feature allows HSRP groups to use an interface's burnedin MAC address
instead of an HSRP MAC address. Use BIA was first implemented in Cisco IOS release 11.1(8). To configure
HSRP to use the BIA, use the standby usebia [scope interface] command.
The usebia command was implemented to overcome the limitations of using a functional address for the
HSRP MAC address on Token Ring interfaces.
Note: When HSRP runs in a multiplering sourcerouted bridging environment and the HSRP routers reside
on different rings, using the functional addresses can cause Routing Information Field (RIF) confusion. For
this reason, the usebia command was introduced.
The usebia feature also enables the use of DECnet, Xerox Network Systems (XNS), and HSRP on the same
router by allowing the DECnet MAC address (the BIA) to be used as the HSRP MAC address. The usebia
command is also useful in networking situations where a device's BIA has been configured in other devices on
the LAN.
However, the usebia command has several disadvantages:
When a router becomes active, the virtual IP address is moved to a different MAC address. The newly
active router sends a gratuitous ARP response, but not all host implementations handle the gratuitous
ARP correctly.

Proxy ARP breaks when usebia is configured. A atandby router cannot cover for the lost proxy ARP
database of a failed router.

Prior to Cisco IOS release 12.0(3.4)T, only one HSRP group is allowed if usebia is configured.
When you configure the usebia command on a subinterface, it actually shows up on the main interface and
is applied to all subinterfaces. In Cisco IOS release 12.0(6.2) and later, the usebia command is extended
with the optional scope interface keywords to allow it to be applied to a single subinterface.
This defect has Cisco bug ID CSCdm25468 (registered customers only) .
Multiple HSRP Groups
The multiple HSRP (MHSRP) groups feature was added in Cisco IOS release 10.3. This feature further
enables redundancy and loadsharing within networks, and allows redundant routers to be more fully utilized.
While a router is actively forwarding traffic for one HSRP group, it can be in standby or in the listen state for
another group.
As of Cisco IOS release 12.0(3.4)T, you can use the usebia command with multiple HSRP groups enabled.
Refer to Load Sharing with HSRP to configure HSRP in order to take advantage of multiple paths.
Configurable MAC Address
Normally you use HSRP to help end stations locate the first hop gateway for IP routing. The end stations are
configured with a default gateway. However, HSRP can provide first hop redundancy for other protocols.
Some protocols, such as Advanced PeertoPeer Networking (APPN), use the MAC address to identify the
first hop for routing purposes.
In this case, it is often necessary to be able to specify the virtual MAC address using the standby
macaddress command. The virtual IP address is unimportant for these protocols. The actual syntax of the
command is standby [group] macaddress macaddress.
Note: You cannot use this command on a Token Ring interface.
Syslog Support
Support for syslog messaging for HSRP information was added in Cisco IOS release 11.3. This feature allows
for more efficient logging and tracking of the current active and standby routers on syslog servers.
HSRP Debugging
Before Cisco IOS release 12.1, the HSRP debugging command was relatively simple. To enable HSRP
debugging, you would simply use the debug standby command, which enabled output of HSRP state and
packet information for all standby groups on all interfaces.
A debug condition was added in Cisco IOS release 12.0(2.1) that allows the output from the standby debug
command to be filtered based upon interface and group number. The command utilizes the debug condition
paradigm introduced in Cisco IOS release 12.0, as follows: debug condition standby interface group . The
interface you specify must be a valid interface capable of supporting HSRP. The group can be any group (0
255).
You can set debug conditions for groups that do not exist, which allows you to capture debug information
during the initialization of a new group.
You must enable standby debug order for any debug output to be produced. If you don't configure any
standby debug conditions, then debug output is produced for all groups on all interfaces. If you configure at
least one standby debug condition, then standby debug output is filtered according to all standby debug
conditions.
Enhanced HSRP Debugging
Before Cisco IOS release 12.1(0.2), HSRP debugging was of limited use because information was lost in the
noise from periodic hello messages. Thus the enhanced debugging feature was added in Cisco IOS 12.1(0.2).
The following table explains the command options for enhanced debugging.
Command
Description
debug standby Displays all HSRP errors,
events, and packets.
debug standby terse
Displays all HSRP errors,
events, and packets, except
hello and advertisement
packets.
debug standby errors
Displays HSRP errors.
debug standby events [[all |
terse] | [icmp | protocol |
redundancy | track]] [detail]
Displays HSRP events.
debug standby packets [[all |
terse] | [advertise | coup |
hello | resign]] [detail]
Displays HSRP packets.
You can filter the debug output using interface and HSRP group conditional debugging. To enable interface
conditional debugging, use the debug condition interface interface command. To enable HSRP conditional
debugging, use the debug condition standby interface group command.
An interface debug condition applies only when you have set no standby debug conditions. HSRP debugging
is further enhanced in Cisco IOS software release 12.1(1.3), based on the improvements that were made to the
HSRP state table.
This defect has Cisco bug ID CSCdp57811 (registered customers only) .
These enhancements display the HSRP state table events. In the output below the a/, b/, c/, and so on, refer to
the events of the HSRP finite state machine, which are documented in RFC 2281 .
SB1: Ethernet0/2 Init: a/HSRP enabled
SB1: Ethernet0/2 Active: b/HSRP disabled (interface down)
SB1: Ethernet0/2 Listen: c/Active timer expired (unknown)
SB1: Ethernet0/2 Active: d/Standby timer expired (20.0.0.3)
SB1: Ethernet0/2 Speak: f/Hello rcvd from higher pri Speak router
SB1: Ethernet0/2 Active: g/Hello rcvd from higher pri Active router
SB1: Ethernet0/2 Speak: h/Hello rcvd from lower pri Active router
SB1: Ethernet0/2 Standby: i/Resign rcvd
SB1: Ethernet0/2 Active: j/Coup rcvd from higher pri router
SB1: Ethernet0/2 Standby: k/Hello rcvd from higher pri Standby router
SB1: Ethernet0/2 Standby: l/Hello rcvd from lower pri Standby router
SB1: Ethernet0/2 Active: m/Standby mac address changed
SB1: Ethernet0/2 Active: n/Standby IP address configured
Authentication
The HSRP authentication feature consists of a shared cleartext key contained within the HSRP packets. This
feature prevents the lower priority router from learning the standby IP address and standby timer values from
the higher priority router.
To configure the HSRP authentication string, use the standby authentication string command.
IP Redundancy
HSRP provides stateless redundancy for IP routing. HSRP by itself is limited to maintaining its own state. It
assumes that each router builds and maintains its own routing tables independently of other routers. The IP
redundancy feature provides a mechanism that allows HSRP to provide a service to client applications so that
they can implement statefull failover.
IP redundancy does not provide a mechanism for peer applications to exchange state information. This is left
to the applications themselves, and is essential if the applications are to provide statefull failover.
IP redundancy is currently (as of January 2000) implemented only for Mobile IP Home Agents. Following is a
sample configuration:
configure terminal
router mobile
ip mobile homeagent standby hsrpgroup1
!
interface e0/2
no shutdown
ip address 20.0.0.1 255.0.0.0
standby 1 ip 20.0.0.11
standby 1 name hsrpgroup1
Note: As of Cisco IOS release 12.1(3)T, the keyword redundancy is accepted in addition to the keyword
standby. The standby keyword will be phased out in a later Cisco IOS release. The correct command will
then be ip mobile homeagent redundancy hsrpgroup1.
Future uses of IP Redundancy may include:
NAT Need to provide redundant gateways.
IPSEC Need to synchronize state information in order to operate when HSRP is in use.
DHCP Server DHCP servers implemented in various routers.
NBAR, CBAC Need to mirror firewall states for asymmetric routing.
GPRS Needs a way to track TCP state.
PIX
SNMP Management Information Base
SNMP Management Information Base (MIB) support was added to Cisco IOS release 12.0(3.0)T. There are
two relevant MIBs for HSRP:
ciscoMgmt 106: The MIB module for managing HSRP
ciscoMgmt 107: The extension MIB module for managing HSRP
Prior to Cisco IOS release 12.0(6.1)T, a walk of the extended HSRP MIB when a Bridge Group Virtual
Interface (BVI) is present causes the router to crash.
This defect has Cisco bug ID CSCdm61257 (registered customers only) .
HSRP Support for Multiprotocol Label Switching Virtual Private Networks
HSRP support for Multiprotocol Label Switching Virtual Private Networks (MPLS VPNs) was added in
Cisco IOS release 12.1(3)T.
HSRP on an MPLS VPN interface is useful when you have an Ethernet connected between two Provider
Edges (PEs) and you have either of the following:
A Customer Edge (CE) with a default route to the HSRP virtual IP address.
One or more hosts with the HSRP virtual IP address configured as the default gateway.
The network diagram below shows two PEs with HSRP running between their VPN routing/forwarding
(VRF) interfaces. We configured the CE with the HSRP virtual IP address as its default route. And we
configured HSRP to track the interfaces connecting the PEs to the rest of the provider network. For example,
if interface E1 of PE1 fails, the HSRP priority will be reduced such that PE2 takes over forwarding packets to
the virtual IP/MAC address.
These are the configurations:
Router PE1
Router PE2
conf terminal
!
ip cef
!
ip vrf vrf1
rd 100:1
routetarget export 100:1
routetarget import 100:1
!
interface ethernet0
no shutdown
ip vrf forwarding vrf1
ip address 10.2.0.1 255.255.0.0
standby 1 ip 10.2.0.20
standby 1 priority 105
standby 1 preempt delay minimum 10
standby 1 timers 3 10
standby 1 track ethernet1 10
standby 1 track ethernet2 10
conf terminal
!
ip cef
!
ip vrf vrf1
rd 100:1
routetarget export 100:1
routetarget import 100:1
!
interface ethernet0
no shutdown
ip vrf forwarding vrf1
ip address 10.2.0.2 255.255.0.0
standby 1 ip 10.2.0.20
standby 1 priority 100
standby 1 preempt delay minimum 10
standby 1 timers 3 10
standby 1 track ethernet1 10
standby 1 track ethernet2 10
You can use the following commands to verify that the HSRP virtual IP address is in the correct VRF ARP
and Cisco Express Forwarding tables:
ed1pe1# show ip arp vrf vrf1
Protocol Address Age (min) Hardware Addr Type Interface
Internet 10.2.0.1 00d0.bbd3.bc22 ARPA Ethernet0/2
Internet 10.2.0.20 0000.0c07.ac01 ARPA Ethernet0/2
ed1pe1# show ip cef vrf vrf1
Prefix Next Hop Interface
0.0.0.0/0 10.3.0.4 Ethernet0/3
0.0.0.0/32 receive
10.1.0.0/16 10.2.0.1 Ethernet0/2
10.2.0.0/16 attached Ethernet0/2
10.2.0.1/32 receive
10.2.0.20/32 receive
224.0.0.0/24 receive
255.255.255.255/32 receive
HSRP Support for ICMP Redirects
HSRP is based on the concept that the HSRP peer routers protecting a subnet can provide access to all other
subnets that comprise the network. Therefore, it is irrelevant which router becomes the active HSRP router, as
all routers had routes to every subnet.
HSRP makes use of a special virtual IP address and virtual MAC address, which are logically attached to the
HSRP active router. ICMP redirects are automatically disabled on an interface when using HSRP on that
interface. IOS 12.1(3)T onwards, ICMP Redirects feature enables ICMP redirects on interfaces configured
with HSRP. Refer to HSRP Support for ICMP Redirects for more details. This is done to prevent hosts from
being redirected away from the HSRP virtual IP address. It is possible that the two (or more) routers on a
subnet don't have identical connectivity to the rest of the network. That is, for a particular destination IP
address, one or the other of the routers may have a much better path to that address, or may even be the only
router attached to that address.
The ICMP protocol allows a router to redirect an endstation to send packets for a particular destination to
another router on the same subnet, if the first router knows that the other router has a better path to that
particular destination. As was the case for default gateways, if the router to which an endstation has been
redirected for a particular destination fails, then the endstation's packets to that destination were not delivered.
In standard HSRP, this is exactly what happens. For this reason, we recommend disabling ICMP redirects if
HSRP is turned on.
Extending the relationship between ICMP redirects and HSRP provides a solution to this problem, allowing
you to take advantage of the benefits of both HSRP and ICMP redirects. Two (or more) HSRP groups are run
on each subnet, with at least as many HSRP groups configured as there are routers participating. The priorities
are configured so that each of the routers is master of at least one HSRP group. When one router determines to
redirect an endstation to a different router for a specific destination, then instead of redirecting the endstation
to that other router's IP address, it finds an HSRP group that is being mastered by that router, and redirects the
endstation to the corresponding virtual IP address. If that target router then fails, HSRP ensures that another
router takes over its job and, perhaps, redirects the endstation to yet another, again virtual, router.
HSRP Interface and Media Support
This section explains which interfaces and media HSRP supports, and possible caveats when running HSRP
over these media.
Since Cisco IOS Software release 10.0, HSRP functionality has been available on Ethernet, Token Ring and
Fiber Distributed Data Interface (FDDI). Fast Ethernet and ATM interfaces are also supported by HSRP.
Virtual LANs (VLANs) allow logical network topologies to overlay the physical switched infrastructure such
that any arbitrary collection of LAN ports can be combined into an autonomous user group or community of
interest. HSRP VLAN support was added in Cisco IOS release 11.1 for IEEE 802.10 Secure Data Exchange
(SDE), and in Cisco IOS release 11.3 for Cisco InterSwitch Link (ISL).
Ethernet
Several Ethernet (Lance and QUICC) controllers in lowend products can only have a single unicast MAC
address in their address filter. On these platforms only a single HSRP group is permitted, and the interface
address is changed to the HSRP virtual MAC address when the group becomes Active. If you are using HSRP
on routers with multiple interfaces of this type, you should configure each interface with a different HSRP
group number.
Note: The Cisco 7200 router also uses the Lance Ethernet controller, but it supports MHSRP in software.
Cisco recommends that you have no more than twentyfour HSRP Ethernet Interface Processors (EIPs) due to
the time it takes to update the address filters for HSRP. Having more than twentyfour HSRP EIPs can cause
instability and excessive CPU load.
This defect has Cisco bug ID CSCdj29595 (registered customers only) .
If you have more than twentyfour EIPs, try replacing the EIPs with Versatile Interface Processors (VIPs) and
Ethernet port adapters. VIPs have been approved for up to eighty HSRP groups. You can also reduce the
number of HSRP groups, and increase the HSRP hello and hold time.
Token Ring
One limitation of running HSRP on a Token Ring interface is that you cannot reprogram the address filter on
the Token Ring chipset the same way you can on Ethernet, FDDI or ATM emulation. Token Ring uses
functional addresses, of which there are only a small number available that do not conflict with other uses of
the functional address space.
When running HSRP in a sourceroute bridging (SRB) environment, the use of functional addresses can
cause RIF confusion. See the HSRP Addressing section for more information. Also, try configuring the
usebia command.
802.1Q
Cisco recommends using Cisco IOS software release 12.0(8.1)T or later for HSRP over 802.1Q.
ISL
HSRP over ISL is available in Cisco IOS releases 11.2(6)F, 11.3, 12.X. It is recommended to use release
12.0(7) or later in order to avoid the issue described in Cisco bug ID CSCdm68811 (registered customers
only) .
FDDI
A FDDI port adapter strips frames from the ring if it sees one of its own MAC addresses in the MAC source.
If a network event causes both routers to go active, then both routers send HSRP hello packets with the same
virtual MAC address. Each router mistakenly strips the other router's hello packet from the network, and both
stay active.
This defect has Cisco bug ID CSCdj30049 (registered customers only) .
The solution to this problem in Cisco IOS release 11.2(11.1) is for HSRP routers in an FDDI environment to
use their own unique burnedin MAC address to exchange messages and run the HSRP protocol. To ensure
that learning bridges and switches cache the correct port entry for the virtual MAC address, the active router
also sends periodic refresh messages using the HSRP MAC address.
Note: The Cisco 4500 router's hardware contentaddressable memory (CAM) on an FDDI interface may not
be populated correctly after a reload if you have configured multiple RIP networks and HSRP groups. The
only workaround at this time is to clear the interfaces to restore the CAM. This defect has Cisco bug ID
CSCdm93122 (registered customers only) .
MAC Refresh
HSRP routers in an FDDI environment use their own unique burnedin MAC address to exchange messages
and run the HSRP protocol. To ensure that learning bridges and switches cache the correct port entry for the
virtual MAC address the active router also sends periodic refresh messages using the HSRP MAC address.
This defect has Cisco bug ID CSCdj30049 (registered customers only) .
If you do not have a switch or learning bridge on your network, you can disable the sending of refresh packets
as shown below:
interface fddi 1/0/0
ip address 10.1.1.1 255.255.255.0
standby ip 10.1.1.250
standby macrefresh 0
Bridge Group Virtual Interface
HSRP support for Bridge Group Virtual Interfaces (BVIs) was added in Cisco IOS release 12.0(6.2)T.
Subinterfaces
HSRP groups on subinterfaces must have a group number unique among all other groups on all subinterfaces
on the same main interface. This is because subinterfaces do not receive a unique SNMP interface index. If
you had two groups with the number N on different subinterfaces, then in the MIB, group N on subinterface
1 and group N on subinterface 2 would appear to be the same group.
Related Information
HSRP Support Page
HSRP FAQ
Technical Support & Documentation Cisco Systems
Contacts & Feedback | Help | Site Map
2013 2014 Cisco Systems, Inc. All rights reserved. Terms & Conditions | Privacy Statement | Cookie Policy | Trademarks of
Cisco Systems, Inc.
Updated: May 25, 2006 Document ID: 9234

You might also like