Cutler-Hammer Instructions For Installation, Operation and Maintenance of Type DHP-VR Vaccum Replacement Circuit Breakers For DHP Switchgear

Download as pdf or txt
Download as pdf or txt
You are on page 1of 49

I. B.

6513C80C
Effective 11/97 Supersedes I.B.6513C80-B dated September, 1993
Cutler-Hammer
Instructions for Installation, Operation and Maintenance
of Type DHP-VR Vaccum Replacement Circuit Breakers for
DHP Switchgear
DHP-VR
5 kV Rating
DHP-VR
7.5 and 15 kV Ratings
I. B. 6513C80C Page iii
Effective 11/97
Cutler-Hammer
Power Distribution Components Division
Five Parkway Center
Pittsburgh, PA 15220
All possible contingencies which may arise during installation, operation or maintenance, and all details and
variations of this equipment do not purport to be covered by these instructions. If further information is
desired by purchaser regarding his particular installation, operation or maintenance of particular equipment,
contact a Cutler-Hammer representative.
IMPROPERLY INSTALLING OR MAINTAINING
THESE PRODUCTS CAN RESULT IN DEATH, SERI-
OUS PERSONAL INJURY OR PROPERTY DAMAGE.
READ AND UNDERSTAND THESE INSTRUCTIONS
BEFORE ATTEMPTING ANY UNPACKING, ASSEM-
BLY, OPERATION OR MAINTENANCE OF THE CIR-
CUIT BREAKERS.
INSTALLATION OR MAINTENANCE SHOULD BE
ATTEMPTED ONLY BY QUALIFIED PERSONNEL.
THIS INSTRUCTION BOOK SHOULD NOT BE CON-
SIDERED ALL INCLUSIVE REGARDING INSTALLA-
TION OR MAINTENANCE PROCEDURES. IF FUR-
THER INFORMATION IS REQUIRED, YOU SHOULD
CONSULT CUTLER-HAMMER.
THE CIRCUIT BREAKERS DESCRIBED IN THIS
BOOK ARE DESIGNED AND TESTED TO OPERATE
WITHIN THEIR NAMEPLATE RATINGS. OPERATION
OUTSIDE OF THESE RATINGS MAY CAUSE THE
EQUIPMENT TO FAIL, RESULTING IN DEATH, BODI-
LY INJURY AND PROPERTY DAMAGE.
ALL SAFETY CODES, SAFETY STANDARDS
AND/OR REGULATIONS AS THEY MAY BE
APPLIED TO THIS TYPE OF EQUIPMENT MUST BE
STRICTLY ADHERED TO.
THESE CIRCUIT BREAKER ELEMENTS ARE
DESIGNED TO BE INSTALLED PURSUANT TO THE
AMERICAN NATIONAL STANDARDS INSTITUTE
(ANSI). SERIOUS INJURY, INCLUDING DEATH,
CAN RESULT FROM FAILURE TO FOLLOW THE
PROCEDURES OUTLINED IN THIS MANUAL.
THESE CIRCUIT BREAKER ELEMENTS ARE SOLD
PURSUANT TO A NON-STANDARD PURCHASING
AGREEMENT WHICH LIMITS THE LIABILITY OF
THE MANUFACTURER.
!
WARNING
!
WARNING
I. B. 6513C80C Page iv
Effective 11/97
TABLE OF CONTENTS
PAGE
SECTION 1 INTRODUCTION
1-1 Available DHP-VR Breakers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
SECTION 2 SAFE PRACTICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
SECTION 3 RECEIVING, HANDLING AND STORAGE
3-1 Receiving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
3-2 Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
3-3 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
3-4 DHP-VR Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
SECTION 4 INSTALLATION
4-1 Initial Inspection and Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
4-2 SURE CLOSE MECHANISM Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
4-3 Mechanism Operated Cell (MOC) Switch Pantograph Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
4-4 Manual Operation Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
4-5 Vacuum Interrupter Integrity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
4-6 Insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
4-7 Contact Erosion and Wipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
4-8 Primary Circuit Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
4-9 Nameplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
4-10 Snubber Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
4-11 Electrical Operations Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
4-12 Lever Breaker Into Cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
4-13 Removing Breaker From Cell . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
SECTION 5 DESCRIPTION AND OPERATION
5-1 Interrupter Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
5-1.1 Vacuum Interrupter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
5-1.2 Contact Erosion Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
5-1.3 "T" Cutout Loading Spring Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
5-1.4 Contact Wipe and Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
5-1.5 Phase Barriers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
5-2 Stored Energy Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
5-2.1 Operation of Stored Energy Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
5-2.2 Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
5-2.3 Closing Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
5-2.4 Tripping Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
5-2.5 Trip Free Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
5-3 Control Scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
5-3.1 Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
5-3.2 Secondary Disconnects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
I. B. 6513C80C Page v
Effective 11/97
PAGE
5-4 Interlocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
5-4.1 Breaker-Cell Coding Plates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
5-4.2 Levering-in Interlock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
5-4.3 Anti-Close Interlock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
5-4.4 Floor Tripping and Closing Spring Release Interlocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
5-4.5 Rail Latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
5-5 Miscellaneous Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
5-5.1 Ground Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
5-5.2 MOC and TOC Switch Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
5-5.3 Operations Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
5-6 Levering Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
SECTION 6 INSPECTION AND MAINTENANCE
6-1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
6-2 Frequency of Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
6-3 Inspection and Maintenance Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
6-4 Vacuum Interrupter Integrity Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
6-5 Contact Erosion and Wipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
6-6 Insulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
6-7 Insulation Integrity Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
6-8 Primary Circuit Resistance Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
6-9 Mechanism Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
6-10 Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
6-11 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
SECTION 7 RENEWAL PARTS
7-1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
7-1.1 Ordering Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
TABLES
Table Title Page
1.1 Type DHP-VRVaccum Circuit Breaker Availability and Interchangeability ...........................................1
3.1 DHP-VR Weights.......................................................................................................................................7
5.1 Typical Opening and Closing Times........................................................................................................27
6.1 Vacuum Interrupter Integrity Test Voltage...............................................................................................36
I. B. 6513C80C Page vi
Effective 11/97
FIGURES
Figure Title Page
1-1 Outline and Dimensions (inches) Type DHP-VR Breakers (5 kV, 250 MVA Rating).................................2
1-2 Outline and Dimensions (inches) Type DHP-VR Breakers (5 kV, 350 MVA Rating).................................3
1-3 Outline and Dimensions (inches) Type DHP-VR Breakers (7.5 kV and 15 kV Ratings)............................4
3-1 Typical DHP-VR Tools and Accessories ...................................................................................................6
3-2 Front External View of DHP-VR Breaker (5 kV, 250 MVA Rating) ............................................................8
3-3 Rear External View of DHP-VR Breaker (5 kV, 250 MVA Rating).............................................................9
3-4 Front External View of DHP-VR Breaker (7.5 and 15 kV, 500 and 750 MVA Ratings) ...........................10
3-5 Rear External View of DHP-VR Breaker (7.5 and 15 kV, 500 and 750 MVA Ratings) ............................11
4-1 MOC Drive Spring....................................................................................................................................13
4-2 Drive Spring Adjusted for 0 to 1 MOC Switch..........................................................................................13
4-3 Drive Spring Adjustment Graphic ............................................................................................................13
4-4 Checking Drive Spring for Proper Adjustment for One Installed Moc Switch ..........................................13
4-5 Drive Spring Shown Adjusted for 2 MOC Switches.................................................................................14
4-6 Drive Spring Shown Adjusted for 3 MOC Switches.................................................................................14
4-7 MOC Pantograph Adjustment..................................................................................................................14
4-8 Snubber Adjustment ................................................................................................................................16
4-9 Positioning of 5 kV DHP-VR Breaker.......................................................................................................17
4-10 Positioning of 7.5 or 15 kV DHP-VR Breaker ..........................................................................................18
4-11 Final Engagement of 5 kV Secondary Contact........................................................................................18
4-12 Final Engagement of 7.5 or 15 kV Secondary Contact ...........................................................................18
4-13 Levering 5 kV Breaker to Connected Position.........................................................................................19
4-14 Levering 7.5 or 15 kV Breaker to Connected Position.............................................................................19
5-1 DHP-VR 5 kV Interrupter Assembly.........................................................................................................20
5-2 DHP-VR 7.5 or 15 kV Interrupter Assembly ............................................................................................20
5-3 DHP-VR 5 kV Design - Front Faceplate Removed..................................................................................23
5-4 DHP-VR 7.5 or 15 kV Design - Front Faceplate Removed......................................................................24
5-5 Closing Cam and Trip Linkage ................................................................................................................25
5-6 Charging Schematic ................................................................................................................................26
5-7 Typical DHP-VR DC and AC Control Schemes..................................................................................28
5-8 Male Secondary Contact Block (In Extended Position) On 5 kV DHP-VR Breaker.................................29
5-9 Male Secondary Contact Block (In Extended Position) On 15 kV DHP-VR Breaker...............................29
5-10 Code Plate Installed On 5 kV DHP-VR Breaker ......................................................................................30
5-11 Code Plate Installed On 15 kV DHP-VR Breaker ....................................................................................30
5-12 DHP-VR Breaker (5 kV) Floor Tripping Levers (Underneath Front View) ...............................................31
5-13 DHP-VR Breaker (7.5 or 15 kV) Floor Tripping Lever (Underneath Rear View)......................................31
5-14 DHP-VR Breaker (5 kV) Rail Latch..........................................................................................................31
5-15 DHP-VR Breaker (7.5 or 15 kV) Rail Latch..............................................................................................31
5-16 DHP-VR Breaker Ground Contact ...........................................................................................................32
5-17 DHP-VR Breaker (5 kV) Levering-in Device Nut Housing .......................................................................33
5-18 DHP-VR Breaker (7.5 or 15 kV) Levering-in Device Nut Housing...........................................................33
6-1 Lubrication Points ....................................................................................................................................34
6-2 Vacuum Interrupter Showing Contact Erosion Indicator with Breaker Open...........................................37
6-3 Vacuum Interrupter Showing Contact Erosion Indicator with Breaker Closed.........................................37
6-4 T Contact Wipe Indicator Example with Blue Spring ...........................................................................38
6-5 Wipe Indication Procedure.......................................................................................................................38
SECTION 1: INTRODUCTION
The purpose of this book is to provide instructions for
unpacking, storage, installation, operation and mainte-
nance of Type DHP-VR Vacuum Replacement Circuit
Breakers. They are horizontal drawout type removable
interrupting elements for use in existing DHP Metal-Clad
Switchgear. DHP-VR Circuit Breakers provide reliable
control, protection and performance, with ease of han-
dling and maintenance. Like ratings are interchangeable
with each other.
1-1 AVAILABLE DHP-VR BREAKERS
Refer to Table 1.1.
I. B. 6513C80C Page 1
Effective 11/97
!
WARNING
SATISFACTORY PERFORMANCE OF THESE
BREAKERS IS CONTINGENT UPON PROPER
APPLICATION, CORRECT INSTALLATION AND
ADEQUATE MAINTENANCE. THIS INSTRUCTION
BOOK MUST BE CAREFULLY READ AND FOL-
LOWED IN ORDER TO OBTAIN OPTIMUM PERFOR-
MANCE FOR LONG USEFUL LIFE OF THE CIRCUIT
BREAKERS.
TYPE DHP-VR BREAKERS ARE PROTECTIVE
DEVICES, AS SUCH, THEY ARE MAXIMUM RATED
DEVICES. THEREFORE, THEY SHOULD NOT
UNDER ANY CIRCUMSTANCE BE APPLIED OUT-
SIDE THEIR NAMEPLATE RATINGS.
Published DHP-VRVacuum Circuit Breaker ratings are per
current revision of ANSI C37.06 (symmetrical current basis).
Existing breaker rated per ANSI C37.06-1961 Table 2 (total
current basis.
Existing breaker rated post ANSI C37.06-1964 (symmetrical current basis).
At rated maximum kV.
K times rated short circuit current (KI).
xx 50DHP250 enclosures must be uprated to be compatible
with 50DHP-VR250U ratings
Existing Rated
DHP or DVP Continuous
Breaker Type Current at
60 Hz
(Amps)
50DHP250 1200
50DHP250 2000
H50DHP250 1200
H50DHP250 2000
XX 1200
XX 2000
50DHP350 1200
50DHP350 2000
75DHP500 1200
75DHP500 2000
75DVP500 1200
75DVP500 2000
150DHP500 1200
150DHP500 2000
150DVP500 1200
150DVP500 2000
H150DHP500 1200
H150DHP500 2000
150DHP750 1200
150DHP750 2000
150DHP750C 1200
150DHP750C 2000
150DVP750 1200
150DVP750 2000
H150DHP750 1200
H150DHP750 2000
H150DHP750C 1200
H150DHP750C 2000
150DHP1000 1200
150DHP1000 2000
DHP-VR Rated
Replacement Continuous
Breaker Type Current at
60 Hz
(Amps)
50DHP-VR250 1200
50DHP-VR250 2000
50DHP-VR250H 1200
50DHP-VR250H 2000
50DHP-VR250U 1200
50DHP-VR250U 2000
50DHP-VR350 1200
50DHP-VR350 2000
75DHP-VR500 1200
75DHP-VR500 2000
75DHP-VR500 1200
75DHP-VR500 2000
150DHP-VR500 1200
150DHP-VR500 2000
150DHP-VR500 1200
150DHP-VR500 2000
150DHP-VR500H 1200
150DHP-VR500H 2000
150DHP-VR750 1200
150DHP-VR750 2000
150DHP-VR750C 1200
150DHP-VR750C 2000
150DHP-VR750 1200
150DHP-VR750 2000
150DHP-VR750H 1200
150DHP-VR750H 2000
150DHP-VR750CH 1200
150DHP-VR750CH 2000
150DHP-VR1000 1200
150DHP-VR1000 2000
Rated
Voltage
Factor
K
1.24
1.24
1.24
1.24
1.19
1.19
1.19
1.19
1.25
1.25
1.25
1.25
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.30
1.30
Rated Withstand
Test Voltage
Low Freg. Impulse
kV RMS kV Crest
19 60
19 60
19 60
19 60
19 60
19 60
19 60
19 60
36 95
36 95
36 95
36 95
36 95
36 95
36 95
36 95
36 95
36 95
36 95
36 95
36 95
36 95
36 95
36 95
36 95
36 95
36 95
36 95
36 95
36 95
Rated
Short-
Circuit
Current
kA RMS
29
29
29
29
41
41
41
41
33
33
33
33
18
18
18
18
18
18
28
28
28
28
28
28
28
28
28
28
37
37
Maximum
Sym.
Interrupting
Capability
kA RMS
36
36
36
36
49
49
49
49
41
41
41
41
23
23
23
23
23
23
36
36
36
36
36
36
36
36
36
36
48
48
Closing
and Latch-
ing Capa-
bility kA
RMS/Crest
58/97
58/97
78/132
78/132
78/132
78/132
78/132
78/132
66/111
66/111
66/111
66/111
37/62
37/62
37/62
37/62
58/97
58/97
58/97
58/97
58/97
58/97
58/97
58/97
77/130
77/130
77/130
77/130
77/130
77/130
Table 1.1 DHP-VRVacuum Circuit Breaker Availability and Interchangeability
Nominal
Voltage
Class
(kV)
4.16
4.16
4.16
4.16
4.16
4.16
4.16
4.16
7.2
7.2
7.2
7.2
13.8
13.8
13.8
13.8
13.8
13.8
13.8
13.8
13.8
13.8
13.8
13.8
13.8
13.8
13.8
13.8
13.8
13.8
Rating A B C D
250 22.40 21.88 48.76 24.03
250U 22.40 21.88 48.76 24.03
I. B. 6513C80C Page 2
Effective 11/97
A
B
7.00 7.00
9.12 9.30
TYP.
C
L
BRKR
INSIDE EDGE
OF RAIL GUIDE
D
C
47.23
8.50
16.50
15.12
12.69
Figure 1-1 Outline and Dimensions (inches) Type DHP-VR Breakers (5 kV, 250 MVA Rating)
Rating A B C D
350 22.65 22.38 57.16 29.38
I. B. 6513C80C Page 3
Effective 11/97
A
B
7.00 7.00
9.12 9.30
TYP.
C
L
BRKR
INSIDE EDGE
OF RAIL GUIDE
D
C
47.23
8.50
16.50
15.12
12.69
Figure 1-2 Outline and Dimensions (inches) Type DHP-VR Breakers (5 kV, 350 MVA Rating)
Rating A B C
500 60.75 31.25 34.81
750 60.75 31.25 34.81
750C 73.75 31.00 38.35
1000 73.75 31.00 38.35
I. B. 6513C80C Page 4
Effective 11/97
Figure 1-3 Outline and Dimensions (inches) Type DHP-VR Breakers (7.5 kV and 15 kV Ratings)
10.00 10.00
BKR C
L
A
B
C
10.00
19.75
20.69
I. B. 6513C80C Page 5
Effective 11/97
SECTION 2: SAFE PRACTICES
Type DHP-VR breakers are equipped with high speed,
high energy operating mechanisms. They are designed
with several built-in interlocks and safety features to pro-
vide safe and proper operating sequences.
TO PROTECT THE PERSONNEL ASSOCIATED WITH
INSTALLATION, OPERATION, AND MAINTENANCE
OF THESE BREAKERS, THE FOLLOWING PRAC-
TICES MUST BE FOLLOWED:
Only qualified persons, as defined in the National
Electrical Safety Code, who are familiar with the
installation and maintenance of medium voltage cir
cuits and equipment, should be permitted to work on
these breakers.
Read these instructions carefully before attempting
any installation, operation or maintenance of these
breakers.
Always remove the breaker from the enclosure before
performing any maintenance. Failure to do so could
result in electrical shock leading to death, severe
personal injury or property damage.
Do not work on a breaker with the secondary test cou
pler engaged. Failure to disconnect the test coupler
could result in an electrical shock leading to death,
personal injury or property damage.
!
WARNING
Do not work on a closed breaker or a breaker with
closing springs charged. The closing spring should be
discharged and the main contacts open before work
ing on the breaker. Failure to do so could result in cut
ting or crushing injuries.
Do not use a circuit breaker by itself as the sole
means of isolating a high voltage circuit. Remove the
breaker to the Disconnect position and follow all lock-
out and tagging rules of the National Electrical Code
and any and all applicable codes, regulations and
work rules.
Do not leave the breaker in an intermediate position in
the cell. Always have the breaker either in the Test or
Connected position. Failure to do so could result in a
flash over and possible death, personal injury or prop-
erty damage.
Always remove the maintenance tool from the breaker
after charging the closing springs.
Breakers are equipped with safety interlocks. Do Not
defeat them. This may result in death, bodily injury or
equipment damage.
I. B. 6513C80C Page 6
Effective 11/97
SECTION 3: RECEIVING, HANDLING AND
STORAGE
Type DHP-VR circuit breakers are subjected to com-
plete factory production tests and inspection before
being packed. They are shipped in packages designed
to provide maximum protection to the equipment during
shipment and storage and at the same time to provide
convenient handling. Accessories such as the mainte-
nance tool, levering crank, etc. are shipped separately
(Figure 3-1).
3-1 RECEIVING
Until the breaker is ready to be delivered to the
switchgear site for installation, DO NOT remove it from
the wooden crate. If the breaker is to be placed in stor-
age, maximum protection can be obtained by keeping it
in its crate.
Upon receipt of the equipment, inspect the crates for
any signs of damage or rough handling. Open the crates
carefully to avoid any damage to the contents. Use a
nail puller rather than a crow bar when required.
When opening the crates, be careful that any loose
items or hardware are not discarded with the packing
material. Check the contents of each package against
the packing list.
Examine the breaker for any signs of shipping damage
such as broken, missing or loose hardware, damaged or
deformed insulation and other components. File claims
immediately with the carrier if damage or loss is detect-
ed and notify the nearest Cutler-hammer Sales Office.
Tools and Accessories
Maintenance Tool: Used to charge the closing springs.
(Style 8064A02G01)
Levering Crank: Used to crank the breaker between
Test and Connected positions.
(Style 509A931G01)
Lifting Yoke: Optional item used to lift
the breaker.
5kV. DHP-VR (Style 691C607G03)
7.5/15kV. DHP-VR (Style 691C607G01)
Turning Dolly: Optional item used to help maneuver
breaker when out of structure. (Style 677C889G01)
3-2 HANDLING
DO NOT USE ANY LIFTING DEVICE AS A PLAT-
FORM FOR PERFORMING MAINTENANCE, REPAIR
OR ADJUSTMENT OF THE BREAKER OR FOR
OPENING, CLOSING THE CONTACTS OR CHARG-
ING THE SPRINGS. THE BREAKER MAY SLIP OR
FALL CAUSING SEVERE PERSONAL INJURY.
ALWAYS PERFORM MAINTENANCE, REPAIR AND
ADJUSTMENTS ON A WORKBENCH CAPABLE OF
SUPPORTING THE BREAKER.
Type DHP-VR breaker shipping containers are designed
to be handled either by use of a rope sling and over-
head lifting device or by a fork lift truck. If containers
must be skidded for any distance, it is preferable to use
roller conveyors or individual pipe rollers.
Once a breaker has been inspected for shipping dam-
age, it is best to return it to its original shipping crate
until it is ready to be installed in the Metal-Clad
Switchgear.
When a breaker is ready for installation, a lifting yoke in
conjunction with an overhead lifter or portable floor lifter
can be used to move a breaker, if this is preferable to
rolling the breaker on the floor using self contained
wheels. If the breaker is to be lifted, position the lifting
yoke over the breaker and insert lifters into the breaker
side openings, with the lifting hole toward the inter-
rupters. Once the lifting yoke is securely seated in the
!
WARNING
Figure 3-1 Typical DHP-VR Tools and Accessories
I. B. 6513C80C Page 7
Effective 11/97
lifting holes, the breaker can be carefully lifted and
moved. Keep in mind, however, the faceplate on all 7.5
or 15 kV. DHP-VR breakers must be removed to use a
lifting yoke.
3-3 STORAGE
If the circuit breaker is to be placed in storage, maxi-
mum protection can be obtained by keeping it in the
original wooden crate. Before placing it in storage,
checks should be made to make sure that the breaker is
free from shipping damage and is in satisfactory operat-
ing condition.
The breaker is shipped with its contacts open and clos-
ing springs discharged. The indicators on the front panel
should confirm this. Insert the maintenance tool in the
manual charge socket opening (Figure 3-2 or 3-4).
Charge the closing springs by pumping the handle up
and down about 36 times until a crisp metallic click is
heard. This indicates that the closing springs are
charged and is shown by the closing spring charged
(yellow) indicator. Remove the maintenance tool. Push
the manual close button. The breaker will close as
shown by the breaker contacts closed (red) indicator.
Push the manual trip button. The breaker will trip as
shown by the breaker contacts open (green) indicator.
After completing this initial check, leave the closing
springs discharged and breaker contacts open.
Outdoor storage is NOT recommended. If unavoidable,
the outdoor location must be well drained and a tempo-
rary shelter from sun, rain, snow, corrosive fumes, dust,
dirt falling objects, excessive moisture, etc. must be pro-
vided. Containers should be arranged to permit free cir-
culation of air on all sides and temporary heaters should
be used to minimize condensation. Moisture can cause
rusting of metal parts and deterioration of high voltage
insulation. A heat level of approximately 400 watts for
each 100 cubic feet of volume is recommended with the
heaters distributed uniformly throughout the structure
near the floor.
Indoor storage should be in a building with sufficient
heat and circulation to prevent condensation. If the
building is not heated, the same general rule for heat as
for outdoor storage should be applied.
3-4 DHP-VR WEIGHTS
Refer to Table 3.1.
Circuit Breaker Type Amperes LBs.
50DHP-VR250 1200 435
50DHP-VR250 2000 510
50DHP-VR250U 1200 480
50DHP-VR250U 2000 510
50DHP-VR350 1200 495
50DHP-VR350 2000 525
75DHP-VR500 1200 510
75DHP-VR500 2000 565
150DHP-VR500 1200 480
150DHP-VR500 2000 565
H150DHP-VR500 1200 485
H150DHP-VR500 2000 565
150DHP-VR750 1200 485
150DHP-VR750 2000 565
150DHP-VR750C 1200 515
150DHP-VR750C 2000 595
150DHP-VR1000 1200 575
150DHP-VR1000 2000 600
Table 3.1
I. B. 6513C80C Page 8
Effective 11/97
Figure 3-2 Front External View of DHP-VR Breaker (5k V, 250 MVA Rating)
3
4
7
13
10
9
8
1
2
5
6
11
12
1
2
3
4
5
6
7
8
9
10
11
12
13
Manual Charge Socket
Spring Charged/Discharged Indicator
Operation Counter
Breaker Contacts Indicator
Nameplate
Push To Trip Button
Push To Close Button
Breaker Wheel
Secondary Contact Operating Rod
Secondary Contact Handle
Levering-in Operating Shaft
Turning Dolly Bracket
Removable Faceplate
14
14 Pull/Push Handle
15
15 Rail Latch
I. B. 6513C80C Page 9
Effective 11/97
Figure 3-3 Rear External View of DHP-VR Breaker (5 kV, 250 MVA Rating)
10
7
1
5
4
2
3
5
6
1
2
3
4
5
6
7
8
9
10
11
12
Lifter Yoke Opening
Phase Barrier
Primary Disconnect Contact
Secondary Disconnect Block
Snubber Bolt
Ground Contact
Levering-in Nut Housing
Guide Channel
Breaker Wheel
MOC Switch Operating Mechanism
V-flex Current Connectors
Vaccum Interrupter
8
9
11
12
I. B. 6513C80C Page 10
Effective 11/97
Figure 3-4 Front External View of DHP-VR Breaker (7.5 and 15 kV, 500 and 750 MVA Ratings)
3
4
7
11
8
1
2
5
6
9
10
1
2
3
4
5
6
7
Manual Charge Socket
Spring Charged/Discharged Indicator
Operation Counter
Breaker Contacts Indicator
Nameplate
Push To Trip Button
Push To Close Button
12
8
9
10
11
Secondary Engaging Handle
Levering-in Operating Shaft
Turning Dolly Bracket
Removable Faceplate
12
Pull/Push Handle
I. B. 6513C80C Page 11
Effective 11/97
Figure 3-5 Rear External View of DHP-VR Breaker (7.5 and 15 kV, 500 and 750 MVA Ratings)
9
7
1
5
4
2
3
5
6
1
2
3
4
5
7
8
9
10
Lifter Yoke Opening
Phase Barrier
Primary Disconnect Contact
Secondary Disconnect Block
Snubber Bolt
Levering-in Nut Housing
Guide Channel
MOC Switch Operating Mechanism
Vaccum Interrupter
8
10
6 Ground Contact
I. B. 6513C80C Page 12
Effective 11/97
SECTION 4: INSTALLATION
BEFORE PLACING THE BREAKER IN SERVICE,
CAREFULLY FOLLOW THE INSTALLATION PROCE-
DURE GIVEN BELOW. NOT FOLLOWING THE PRO-
CEDURE CAN FAIL TO UNCOVER SHIPPING DAM-
AGE THAT MAY RESULT IN INCORRECT BREAKER
OPERATION LEADING TO DEATH, BODILY INJURY,
AND PROPERTY DAMAGE.
4-1 INITIAL INSPECTION AND OPERATION
Before attempting to put the breaker in service, it should
be carefully examined and operated manually and elec-
trically.
Examine a breaker for loose or obviously damaged
parts.
4-2 SURE CLOSE MECHANISM ADJUSTMENT
FOR ALL TYPE DHP 15 KV HOUSINGS EQUIPPED
WITH MECHANISM OPERATED CELL (MOC)
SWITCHES, THE STEPS OUTLINED IN THIS PARA-
GRAPH MUST BE PERFORMED BEFORE
INSTALLING A REPLACEMENT DHP-VR CIRCUIT
BREAKER. FAILURE TO COMPLY COULD CAUSE
SEVERE PERSONAL INJURY, DEATH, EQUIPMENT
DAMAGE AND/OR IMPROPER OPERATION.
All 15 kV. Type DHP-VR Breakers utilize the DHP-VR
SURE CLOSE MECHANISM to control MOC velocity
and closely mimic the dynamics and velocities of older
breakers. It is imperative that this mechanism be
adjusted to match the number of MOC switches (from 0
to 3) mounted in the cell. If the adjustment is made on
the DHP-VR breaker to be compatible with one housing
with a given number of MOC switches, make sure the
adjustment is checked and compatible if the breaker is
moved to a different housing.
The breaker has been factory adjusted to operate one
mechanism operated cell (MOC) switch in the cell. This
means that for applications with either no MOC switch
or one MOC switch, no field adjustments are required.
It is only for the cases of 2 or 3 MOC switches that the
drive spring adjustment is required. The adjustment is
done with the breaker out of the cell, open and all
springs discharged. Refer to Figures 4-1 through 4-6
for reference assistance.
Finally, the SURE CLOSE mechanism provides an
effective way to evaluate the condition of the MOC in
the cell. If the SURE CLOSE drive spring is properly
adjusted, but the MOC does not fully open or close, it is
time to maintain the MOC in the cell. Maintenance usu-
ally means cleaning and lubricating the MOC mecha-
nism. If the MOC has seen a large number of cycles,
however, worn components may have to be replaced.
To adjust the SURE CLOSE drive spring for a specific
number of MOC switches, proceed with the following
steps:
Step 1: Remove the right hand phase barrier from the
breaker (Figure 3-5).
Step 2: Locate the MOC drive spring (Figure 4-1). It is
located in the left lower portion of the breaker
as viewed from the top rear of the breaker with
the phase barriers removed.
Step 3: From the factory, the drive spring comes set for
0 or 1 MOC switch. Refer to Figure 4-2 to see
how that adjustment would look. Notice that
there is a nut and a jam nut on the threaded rod
to make the adjustment easy. Also notice that
a step gauge is provided and bolted next to the
spring to further simplify the adjustment
(Figures 4-2 and 4-3).
Step 4: Anytime an adjustment is made, use a straight-
edge to make sure that the flat surface end of
the spring is properly aligned with the correct
step on the gauge for the number of installed
MOC switches. Figure 4-4 shows the alignment
being checked for one installed MOC switch.
Always refer back to the graphic in Figure 4-3 to
ensure adjustment of the spring to the proper
step on the gauge for the number of installed
MOC switches.
Step 5: Refer to Figures 4-5 and 4-6 to see the drive
spring adjusted for 2 installed MOC switches
and 3 installed MOC switches respectively.
Step 6: Any time an adjustment is made, make sure
that all nuts are secured in place and double
check for proper adjust with a straightedge as
described in Step 4.
Step 7: When the adjustment is completed, be sure to
!
WARNING
!
WARNING
I. B. 6513C80C Page 13
Effective 11/97
properly replace and secure the phase barrier
removed in Step 1.
4-3 MECHANISM OPERATED CELL (MOC) SWITCH
Figure 4-1 MOC Drive Spring
Figure 4-2 Drive Spring Adjusted for 0 or 1 MOC Switch
GAUGE
3MOC
2MOC
1MOC
ALIGN THIS
SURFACE WITH
THE STEP ON
THE GAUGE
RELATIVE TO
THE NUMBER
OF MOC
SWITCHES TO
BE OPERATED
Figure 4-3 Drive Spring Adjustment Graphic
Figure 4-4 Checking Drive Spring for Proper
Adjustment for One Installed MOC Switch
Drive Spring
1
M
O
C
2
M
O
C
3
M
O
C
1
MOC
2
MOC
3
MOC
Step Gauge
1
MOC
2
MOC
3
MOC
I. B. 6513C80C Page 14
Effective 11/97
PANTOGRAPH ADJUSTMENT
FOR ALL TYPE DHP HOUSINGS EQUIPPED WITH
MECHANISM OPERATED CELL (MOC) SWITCHES,
THE STEPS OUTLINED IN THIS PARAGRAPH MUST
BE PERFORMED BEFORE INSTALLING A
REPLACEMENT DHP-VR CIRCUIT BREAKER. FAIL-
URE TO COMPLETE THESE STEPS COULD RESULT
IN EQUIPMENT DAMAGE AND/OR IMPROPER
OPERATION.
Inspect the MOC pantograph in keeping with the follow-
ing steps and refer to Figure 4-7 additional assistance.
Step 1: Check for excessive wear in the bearing sur-
faces of all pivoting members.
Step 2: Check that the pantograph assembly is securely
bolted to the housing and that there is no miss-
ing hardware.
Step 3: Check that the top surface of the pantograph
channel is adjusted so the MOC operator pin on
the breaker is centered in the channel.
4-4 MANUAL OPERATION CHECK
Figure 4-5 Drive Spring Shown Adjusted for 2 MOC
Switches
Figure 4-6 Drive Spring Shown Adjusted for 3 MOC
Switches
C
L
ADJ UST HEIGHT OF CHANNEL UNTIL THE MOC
OPERATOR PIN ON THE BREAKER IS CENTERED
IN THE CHANNEL
CHANNEL SHOWN IN THE
OPEN POSITION
MOUNTING
HARDWARE
MOUNTING
HARDWARE
PIVOT
POINTS
BREAKER
FRONT
Figure 4-7 MOC Pantograph Adjustment
!
CAUTION
1
MOC
2
MOC
3
MOC
1
MOC
2
MOC
3
MOC
Place the maintenance tool into the manual charge
socket opening and charge the closing springs with
about 36 up and down strokes of the handle. When
charging is complete, the closing crank goes over center
with an audible click and the springs Charged /
Discharged Indicator shows Charged.
If the springs are to be charged on a closed breaker,
no click is heard at the end of charging operation.
Discontinue charging and remove the maintenance
tool as soon as Charged flag is fully visible.
Continued attempts to further charge may result in
damage to the mechanism.
Remove the maintenance tool.
Close and trip the breaker several times.
4-5 VACUUM INTERRUPTER INTEGRITY
Using a dry lint-free cloth or a paper towel, clean all the
insulating surfaces of the pole units. Conduct a vacuum
interrupter integrity check as described in Section 6-4.
4-6 INSULATION
Check breaker primary and secondary insulation per
Section 6-7.
4-7 CONTACT EROSION AND WIPE
Manually charge the closing springs and close the
breaker. Check contact erosion and wipe as described
in Section 6-5.
4-8 PRIMARY CIRCUIT RESISTANCE
Check the primary circuit resistance as described in
Section 6-8. The resistance should not exceed the val-
ues specified. Record the values obtained for future ref-
erence.
4-9 NAMEPLATE
I. B. 6513C80C Page 15
Effective 11/97
NOTICE
Compare the breaker nameplate information with
switchgear drawings for compatibility. Breaker and com-
partment code plates do match power ratings, but do
not match control voltages.
4-10 SNUBBER ADJUSTMENT
FOR ALL TYPE DHP HOUSINGS, THE ADJUSTMENT
STEPS OUTLINED IN THIS PARAGRAPH MUST BE
PERFORMED BEFORE INSTALLING A REPLACE-
MENT DHP-VR CIRCUIT BREAKER. FAILURE TO
COMPLETE THESE STEPS COULD RESULT IN
EQUIPMENT DAMAGE AND/OR IMPROPER OPERA-
TION.
Before levering a breaker into any and all housings, the
snubber bolts must be adjusted as outlined in steps 1
and 2. Refer to Figures 3-3, 3-5 and 4-8 for reference
purposes. If a breaker is moved from one housing to
another, the procedure must be repeated for the new
housing.
Step 1: Measure the distance from the floor plate to the
underside of the current transformer shelf on
both sides of the housing in line with the loca-
tion of the snubber bolts on each side of the
breaker (Figure 4-8).
Step 2: Adjust the height of the top of the snubber bolt to
be between 0.0 and 0.031 (0.0 and 1/32) inches
below the measured height of the current trans-
former shelf and tighten the locking nut.
4-11 ELECTRICAL OPERATIONS CHECK
After going through the above steps, the breaker is now
ready to be operated electrically. It is preferred that this
check be made with the breaker in the Test position in
the breaker compartment.
Since the Type DHP-VR Circuit Breaker is for use in
existing DHP Metal-Clad Switchgear, installation proce-
dures are similar. If it is necessary to reference anything
in the breaker compartment, refer to the original instruc-
tion books supplied with the assembly.
Refer to Figures 3-2 through 3-5, depending upon the
voltage rating of the breaker, for any parts identification
required during these installation procedures.
a. The circuit breakers faceplate and barriers must be
!
CAUTION
I. B. 6513C80C Page 16
Effective 11/97
SEE VIEW A-A
75/150 DHP-VR Ratings
SEE VIEW A-A SEE VIEW A-A
50 DHP-VR 250/250U Ratings 50 DHP-VR 350 Ratings
VIEW A-A
Snubber Bolt Adjustment
0.00 to
.031
Figure 4-8 Snubber Adjustment
I. B. 6513C80C Page 17
Effective 11/97
positioned properly and securely bolted in position, as
shown in Figures 3-2 through 3-5, before inserting the
breaker into the cell.
EXAMINE THE INSIDE OF THE CELL BEFORE
INSERTING THE BREAKER FOR EXCESSIVE DIRT
OR ANYTHING THAT MIGHT INTERFERE WITH THE
BREAKER TRAVEL.
KEEP HANDS OFF THE TOP EDGE OF THE FRONT
BARRIER WHEN PUSHING A BREAKER INTO A
CELL. FAILURE TO DO SO COULD RESULT IN BOD-
ILY INJURY, IF FINGERS BECOME WEDGED
BETWEEN THE BREAKER AND THE CELL. USE
THE HANDLES PROVIDED ON THE FRONT OF THE
BREAKER FACEPLATE, OR USE BOTH FULLY
OPENED HANDS FLAT ON THE FRONT OF THE
FACEPLATE.
b. Position the breaker in front of the cell, and line up the
guide channel on the rear right hand side of the
breaker near the floor with the guide rail on the right
hand side of the cell floor. Once the breaker is aligned
with the cell floor guide, push the breaker into the cell
until the rail latch at the front of the guide channel
catches in a notch in the guide rail, and prevents fur-
ther movement of the breaker toward the rear of the
cell (Figures 4-9 and 4-10). The breaker is now in the
Test position, and secondary contacts can be
engaged.
As soon as the secondary contacts make up, the
motor will charge the closing spring, if the control
circuit is energized.
c. To engage the secondary contacts on the 5kV.
design, lift the handle on the front left hand side of the
breaker chassis to a horizontal position. Once the rod
is pointing straight out from the breaker, push it manu-
ally to the rear until the secondaries are initially en-
gaged. At this point, the small horizontal pin in the
handle will have engaged two slots in the lever, which
is pivoted immediately above the handle. To insure
complete secondary engagement, push down firmly
on the curved end of the lever as far as it will go,
using your foot or hand (Figure 4-11). When using a
foot, care should be taken not to bend the lever by
using excessive force.
d. To engage the secondary contacts on the 7.5 or
15kV. designs, unlatch the secondary operating rod,
and move it to the left, until it points straight out from
the breaker. Push the rod manually to the rear until
the secondaries are initially engaged. Once initial
engagement is achieved, hold the operating rod firmly
in that position with one hand, while grasping the sec-
ondary engaging handle with the other hand. The sec-
ondary engaging handle is located to the right of the
operating rod, just inside a rectangular hole. By
pulling firmly on the engaging handle, complete sec-
ondary engagement will be insured (Figure 4-12).
e. The breaker may now be electrically closed and
tripped by using a control switch on the cell door, or it
may be manually operated by means of the close and
trip buttons, located on the faceplate of the breaker.
!
WARNING
NOTICE
!
CAUTION
Figure 4-9 Positioning of 5 kV DHP-VR Breaker
I. B. 6513C80C Page 18
Effective 11/97
Figure 4-10 Positioning of 7.5 or 15 kV DHP-VR Breaker
Figure 4-11 Final Engagement of 5 kV Secondary Contact
Figure 4-12 Final Engagement of 7.5 or 15 kV
Secondary Contact
4-12 LEVER BREAKER INTO CELL
Trip the breaker open before attempting to lever it into
the cell. A mechanical interlock will prevent levering the
breaker into or out of the cell, if the breaker is closed.
EXCESSIVE FORCE, APPLIED TO THE LEVERING-
IN MECHANISM WHILE THE BREAKER IS CLOSED,
COULD SHEAR OFF THE PIN THAT THE LEVERING
CRANK ENGAGES DURING OPERATION.
WHILE LEVERING THE BREAKER, NOTE ANY SUD-
DEN RESISTANCE TO LEVERING OR SIGNS OF
BINDING. DETERMINE THE CAUSE OF INTERFER-
ENCE AND CORRECT, AS APPROPRIATE, BEFORE
PROCEEDING
Press down on the rail latch on the front right side of the
breaker with your foot, and push the breaker toward the
rear of the cell as far as it will go. Be sure the breaker is
pushed in until it stops. This will bring the levering nut
on the breaker up to the screw in the cell.
Engage the levering crank on the levering shaft, push
moderately toward rear of cell, and turn crank clockwise.
!
CAUTION
I. B. 6513C80C Page 19
Effective 11/97
The breaker will move slowly toward the rear of the cell.
After the breaker starts to move, it is not necessary to
push (Figures 4-13 and 4-14). Continue cranking until
the crank turns freely, and the breaker stops moving.
When the breaker is fully engaged, the front face-plate
will almost touch the cell frame angles. The breaker is
now in the OPERATING or ENGAGED position, and
may be operated electrically using the control switch on
the cell door.
4-13 REMOVING BREAKER FROM CELL
The breaker may open and its closing spring may
discharge as it is withdrawn from the cell. It
depends on whether the breaker was left closed or
open, or whether the spring was left charged or dis-
charged.
To remove the breaker from the operating position, trip
the breaker open, and engage the levering crank on the
levering device shaft. Turn the crank counterclockwise
until the crank rotates freely. Pull the breaker toward the
front of the cell until the rail latch engages the slot in the
rail. The breaker is now secured in the TEST position.
To remove the breaker from the cell, press down on the
rail latch to free the breaker from the rail. Pull the break-
er out of the cell.
Figure 4-13 Levering 5 kV Breaker to Connected
Position
Figure 4-14 Levering 7.5 or 15 kV Breaker to
Connected Position
NOTICE
I. B. 6513C80C Page 20
Effective 11/97
SECTION 5: DESCRIPTION AND
OPERATION
Cutler-Hammer Type DHP-VR breakers are horizontal
drawout vacuum type removable interrupting elements
for use in existing DHP Metal-Clad Switchgear. The
breakers use vacuum interrupters to close and open the
primary circuit. The mechanism is a front mounted
spring stored energy type, which not only aids with per-
sonnel safety, but also provides ease of inspection and
accessibility for servicing. The same basic mechanism
is used for all ratings.
The DHP-VR vacuum circuit breaker is a direct roll in
replacement for DHP air magnetic and DVP vacuum cir-
cuit breakers. It is wheel mounted for ease of handling
and installation, and rolls in and out of the existing cell
on the floor. Modifications to the existing DHP or DVP
structures are not necessary in order to use DHP-VR
breakers.
DHP-VR vacuum circuit breakers correctly interface with
compartment cell switches (MOC and TOC switches).
Circuit breaker coding plates are maintained to prevent
an underrated circuit breaker from being installed in the
switchgear.
Safety interlocks, inherent in the original switchgear
design and required by ANSI Standards, are also main-
tained.
The primary insulation used on 5kV. DHP-VR vacuum
circuit breakers is glass polyester, while the primary
insulation used on 7.5 and 15 kV. DHP-VR vacuum cir-
cuit breakers is cycloaliphatic epoxy. Type SIS AWG#
14 wire, with cross-linked polyolefin insulation is used
on all DHP-VR control circuits. Secondary control termi-
nations on all DHP-VR breakers are ring type termina-
tions, consistent with existing DHP circuit breakers.
5-1 INTERRUPTER ASSEMBLY
Vacuum interrupters are mounted vertically and are sup-
ported from the fixed stem clamped to the bottom con-
ductor on the 5kV. design (Figure 5-1), and the top con-
ductor on the 7.5 or 15kV. design (Figure 5-2). A close
inspection of the two figures will reveal that the 5kV.
design is actually inverted, relative to the 7.5 or 15kV.
design. In both instances, however, the DHP-VR
includes the Cutler-Hammer patented V-flex current
transfer system. The current transfer system itself con-
sists of a series of tin-plated, high-conductivity copper
leaf conductors that are swaged onto the movable inter-
rupter stem. This provides a multipoint contact resulting
in low electrical and thermal resistance. Since the cur-
rent transfer from the movable stem to the circuit break-
er main conductor is a nonsliding design, no mainte-
nance is required.
Figure 5-1 DHP-VR 5k V Interrupter Assembly Figure 5-2 DHP-VR 7.5 or 15 kV Interrupter Assembly
I. B. 6513C80C Page 21
Effective 11/97
The vacuum interrupter system on all DHP-VR breakers
utilizes a visible T cutout contact loading spring indica-
tor. This T indicator is used to indicate that the loading
springs are maintaining the proper contact pressure to
keep the contacts closed (Figures 5-1 and 5-2).
5-1.1 VACUUM INTERRUPTER
Type DHP-VR breakers utilize vacuum interrupters for
interruption and switching functions. Vacuum interrup-
tion offers the advantages of enclosed interrupters,
reduced size and weight, short interrupting time, long
life, reduced maintenance, and environmental compati-
bility.
Arc interruption is simple and fast. In the closed position,
current flows through the interrupter. When the contacts
are opened, the arc is drawn between the contact sur-
faces. It is rapidly moved around the slotted contact sur-
faces by a selfinduced magnetic force, which prevents
gross contact erosion, as well as the formation of hot
spots on the contact surfaces. The arc burns in an ion-
ized metal vapor, which continually leaves the contact
area and condenses on the surrounding metal shield.
At current zero, the arc is extinguished and vapor pro-
duction ceases. Very rapid dispersion, cooling, recombi-
nation, and deionization of the metal vapor plasma,
together with the fast condensation of metal vapor prod-
ucts, cause the vacuum to be quickly restored. Hence,
the opened contacts withstand the transient recovery
voltage.
5-1.2 CONTACT EROSION INDICATOR
The purpose of the contact erosion indicator is to moni-
tor the erosion of the vacuum interrupter contacts, which
is very minimal over time with Cutler-Hammer vacuum
interrupters utilizing copper-chrome contact material. If
contact erosion reachers 1/8 inch, the interrupter must
be replaced. A contact erosion indicator mark is located
on the moving stem of the interrupter (Figures 6-2 and
6-3).
In order to determine if the contacts have eroded to the
extent that the interrupter must be replaced, close the
breaker and observe the erosion mark placed on each
moving stem from the rear of the breaker. If the mark on
the interrupter stem is visible, the interrupter is satisfac-
tory. It the mark is no longer visible, the interrupter
assembly must be replaced.
The erosion indicator is easily viewed from the rear on
the 7.5 or 15kV. designs. Because of the nature of the
5kV. DHP-VR inverted design, the erosion indicator is
not easily viewed, although it is possible with the use of
a light and a dental type mirror.
5-1.3 T CUTOUT LOADING SPRING INDICATOR
Since the T cutout loading spring indicator is part of all
DHP-VR breaker designs, an additional method is pro-
vided that will indicate conditions within the interrupter,
as well as the overall system condition. The visible T
indicator is used to indicate whether the loading springs
are maintaining the proper contact pressure to keep the
contacts closed. Severe contact erosion would lead to
an unacceptable indication from the T indicator
(Figures 6-4 and 6-5).
5-1.4 CONTACT WIPE AND STROKE
Contact wipe is the indication of (1) the force holding the
vacuum interrupter contacts closed and (2) the energy
available to hammer the contacts open with sufficient
speed for interruption.
Stroke is the gap between fixed and moving contacts of
a vacuum interrupter with the breaker open.
The circuit breaker mechanism provides a fixed amount
of motion to the operating rods. The first portion of the
motion is used to close the contacts (i.e. stroke) and the
remainder is used to further compress the preloaded
wipe spring. This additional compression is called wipe.
Wipe and stroke are thus related to each other. As the
stroke increases due to the erosion of contacts, the wipe
decreases. A great deal of effort has been spent in the
design of all Culter-Hammer vacuum breakers, in order
to eliminate the need for field adjustments of wipe or
stroke.
THERE IS NO PROVISION FOR IN SERVICE
ADJUSTMENTS OF CONTACT WIPE AND STROKE.
ALL SUCH ADJUSTMENTS ARE FACTORY SET AND
SHOULD NOT BE ATTEMPTED IN THE FIELD.
!
CAUTION
I. B. 6513C80C Page 22
Effective 11/97
5-1.5 PHASE BARRIERS
DO NOT PLACE THE BREAKER IN ITS COMPART-
MENT WITHOUT THE PHASE BARRIERS IN PLACE.
THE ABSENCE OF BARRIERS CAN CAUSE A CATA-
STROPHIC FAILURE DURING AN INTERRUPTION
OR OPERATION, CAUSING DEATH, SEVERE PER-
SONAL INJURY OR PROPERTY DAMAGE.
Phase barriers on all DHP-VR breakers are made of
glass polyester. They are all secured in place by bolts,
and are part of the breaker assembly. The 5kV. DHP-
VR breaker utilizes 4 barriers, while the 7.5 or 15 kV.
designs utilize 5 barriers (Figures 3-3 and 3-5).
5-2 STORED ENERGY MECHANISM
KEEP HANDS AND FINGERS AWAY FROM THE
BREAKERS INTERNAL PARTS WHILE THE BREAK-
ER CONTACTS ARE CLOSED OR THE CLOSING
SPRINGS ARE CHARGED. THE BREAKER CON-
TACTS MAY OPEN OR THE CLOSING SPRINGS DIS-
CHARGE CAUSING A CRUSHING INJURY.
DISCHARGE THE SPRINGS AND OPEN THE BREAK-
ER BEFORE PERFORMING ANY MAINTENANCE,
INSPECTION OR REPAIR ON THE BREAKER.
The spring stored energy operating mechanism is
arranged vertically in front of all DHP-VR breakers. It
includes all the elements for storing the energy, closing
and tripping of the breaker, as well as manual and elec-
trical controls. The manual controls are all front accessi-
ble. Motion to close and open the interrupter contacts is
provided through operating rods connecting the mecha-
nism pole shaft to the bell cranks of the interrupter
assemblies (Figures 5-3 and 5-4).
5-2.1 OPERATION OF STORED ENERGY
MECHANISM
The mechanism stores the closing energy by charging
the closing springs. The mechanism may rest in any one
of the four positions shown in Figure 5-5 and as follows:
a. Breaker open, closing springs discharged
b. Breaker open, closing springs charged
c. Breaker closed, closing springs discharged
d. Breaker closed, closing springs charged
5-2.2 CHARGING
Figure 5-6 is a schematic view of the spring charging
parts of the stored energy mechanism.
The major component of the mechanism is a cam shaft
assembly which consists of a drive shaft to which are
attached two closing spring cranks (one on each end),
the closing cam, drive plates, and a free-wheeling
ratchet wheel. The ratchet wheel is actuated by an
oscillating mechanism driven by the motor eccentric.
As the ratchet wheel rotates, it pushes the drive plates
which, in turn, rotate the closing spring cranks and the
closing cam with it.
The closing spring cranks have spring ends connected
to them, which are in turn coupled to the closing springs.
As the cranks rotate, the closing springs are charged.
When the closing springs are completely charged, the
spring cranks go over dead center, and the closing stop
roller comes against the spring release latch. The clos-
ing springs are now held in the fully charged position.
Closing springs may also be charged manually. Insert
the maintenance tool in the manual charging socket
(Figures 3-2 and 3-4). Move it up and down approxi-
mately 36 times until a clicking sound is heard, and the
closing springs charging indicator indicates "Charged".
Any further motion of the maintenance tool will result in
free wheeling of the ratchet wheel.
5-2.3 CLOSING OPERATION
Figure 5-5 shows the positions of the closing cam and
tripping linkage. Note that in Figure 5-5a, in which the
breaker is open and the closing springs are discharged,
the trip "D" shaft and the trip latch are in the unlatched
position.
Once charged, as in Figure 5-5b the closing springs can
be released to close the breaker by moving the spring
release latch out of the way. This is done electrically or
manually by depressing the spring release lever, which
turns the spring release latch out of the way of the clos-
ing stop roller. The force of the closing spring rotates the
cam shaft through the spring cranks. The closing cam,
being attached to the cam shaft, in turn rotates the pole
shaft through the main link to close the breaker.
In Figure 5-5c the linkage is shown with the breaker in
the closed position before the closing sprigs have been
recharged. Interference of the trip "D" shaft with the trip
latch prevents linkage from collapsing, and the breaker
is held closed.
!
WARNING
!
WARNING
I. B. 6513C80C Page 23
Effective 11/97
Figure 5-3 DHP-VR 5 kV Design - Front Faceplate Removed
8
7
4
9
1
2
3
4
5
6
LH Closing Spring
RH Closing Spring
Reset Opening Spring
Spring Release Assembly
Shunt Trip Assembly
Charging Motor
1
7
8
9
10
11
Operations Counter
Motor Cutoff Switch
Closing Cam
Ratchet Wheel
Manual Charge Socket
5
3
11
6
10
2
I. B. 6513C80C Page 24
Effective 11/97
Figure 5-4 DHP-VR 7.5 or 15 kV Design - Front Faceplate Removed
8
7
4
9
1
2
3
4
5
6
LH Closing Spring
RH Closing Spring
Reset Opening Spring
Spring Release Assembly
Shunt Trip Assembly
Charging Motor
1
7
8
9
10
11
Operations Counter
Motor Cutoff Switch
Closing Cam
Ratchet Wheel
Manual Charge Socket
5
3
11
6
10
2
I. B. 6513C80C Page 25
Effective 11/97
Figure 5-5a Breaker Open and Closing
Spring Not Charged
Figure 5-5b Breaker Open and Closing
Spring Charged
Figure 5-5c Breaker Closed and Closing
Spring Not Charged
Figure 5-5d Breaker Closed and Closing
Spring Charged
1
2
3
4
5
6
7
8
9
10
11
12
Pole Shaft
Main Link
Banana Link
Trip Latch
Shunt Trip Lever
Shunt Trip Coil
Cam Shaft
Closing Cam
Operating Rod
Main Link Roller
Trip Bar "D" Shaft
Trip Latch Reset Spring
1
2
3
4
5
6
7
8
9
10
11
12
Figure 5-5 Closing Cam and Trip Linkage
I. B. 6513C80C Page 26
Effective 11/97
Breaker Open, Springs Discharged Breaker Open, Springs Charged
1
2
3
4
5
6
7
8
9
10
11
12
13
14
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Pole Shaft
Anti-Close Interlock
Spring Release (Close) Latch
Spring Crank
Closing Spring
Closing Spring Fixed End
Spring Release (Close) Coil Spring Release Latch (Close Roller)
Spring Release (Close) Clapper
Holding Pawl
Ratchet Wheel
Drive Pawl
Motor Ratchet Lever
Cam Shaft
Figure 5-6 Charging Schematic
When the CS/C contact is made, the SR closes the
breaker. If the CS/C contact is maintained after the
breaker closes, the Y relay is picked-up. The Y/a con-
tact seals in Y until CS/C is opened. The Y/b contact
opens the SR circuit, so that even though the breaker
would subsequently open, it could not be reclosed
before CS/C was released and remade. This is the anti-
pump function.
5-3.1 TIMING
The opening and closing times for the circuit breakers
vary depending upon the control voltage and the power
rating. However, the typical ranges are as follows:
5-3.2 SECONDARY DISCONNECTS
The breaker control wiring is arranged for drawout dis-
connecting by means of a 15 point male plug arranged
to connect to a female receptacle mounted in the rear of
the existing DHP cell. The secondary contact plug is
mounted on a movable bracket on the left side of the
breaker truck (Figures 5-8 and 5-9). This permits it to be
extended to the rear while the breaker is in the test posi-
tion to make with the stationary receptacle in the cell so
that the control circuits are completed. Control wiring
terminates first at terminal blocks mounted at the rear of
the breaker truck, and continues from the terminal
blocks to the male contact plug.
Normally the secondary contacts are held stationary rel-
ative to the breaker chassis. This is accomplished by a
hinged joint in the hand operating rod which acts on the
edge of the lower front truck panel to hold the assembly
in position.
I. B. 6513C80C Page 27
Effective 11/97
Figure 5-5d shows the breaker in the closed position
after the closing springs have been recharged. Note that
the spring charging rotates the closing cam by one half
turn. Since the cam surface in contact with the main link
roller is cylindrical in this region, the spring charging
operation does not affect the mechanism linkage.
Since the primary contacts are completely enclosed in
the vacuum interrupter and not adjustable in any way, a
"Slow Close" capability is not provided with DHP-VR
breakers.
5-2.4 TRIPPING OPERATION
When the trip "D" shaft is turned either by the trip button
or trip coil, all links return to the original "open" condition
shown in Figure 5-5a.
5-2.5 TRIP FREE OPERATION
When the manual trip button is held depressed, any
attempt to close the breaker results in the closing
springs discharging, without any movement of the pole
shaft or vacuum interrupter stem.
5-3 CONTROL SCHEME
There are two basic control schemes for type DHP-VR
breakers, one for DC control and one for AC control
(Figure 5-7). There may be different control voltages or
more than one tripping element, but the principal mode
of operation is as follows:
As soon as the secondary disconnects engage, the
spring charging motor automatically starts charging the
closing springs, provided control power is available.
When the springs are charged, the motor cut off LS1/bb
switch turns the motor off. The breaker may be closed
by making the control switch close (CS/C) contact.
Automatically upon closing of the breaker, the motor
starts charging the closing springs. The breaker may be
tripped any time by making the control switch (CS/T)
contacts.
Note the position switch (PS1) contact in the spring
release circuit in the scheme. This contact remains
made while the breaker is being levered between the
TEST and Connected positions. Consequently, it pre-
vents the breaker from closing automatically, even
though the control switch close contact may have been
made while the breaker is levered to the Connected
position.
Circuit Breaker Type Time in Milliseconds
Closing Time
(From Initiation of Close 45-60
Signal to Contact Make)
Opening Time
(Initiation of Trip Signal 30-45
to Contact Break)
Reclosing Time
(Initiation of Trip 140-165
Signal to Contact Make)
Table 5.1
I. B. 6513C80C Page 28
Effective 11/97
Figure 5-7 Typical DHP-VR DC and AC Control Schemes
51
52 54 56 58
53 55 57
23
13
a b
NOT AVAILABLE WHEN
ST2 OR UV
OPTIONIS CHOSEN
M
Y
SR
ST
1
WL GL RL SPRING
CHARGED
INDICATING
LIGHT
P
N
LS1
bb
3A
1 2
24
CS
C
7
PS1 Y LS2
bb
LS2
aa
4
LC
b
21
Y
b
20
5
a
a
5
19
13
14
10
9
a b a
CS
T
PR
ST
2
UV
9UV
10UV
9A
10A
13
12
52
a
a
51
OPTIONS
D
C

S
O
U
R
C
E
6
5 53
b
3
22
PS2
bb
3
7
6
20 10
9
7 8 9 10
18 17 16 15
REMOVE J UMPER FROM BREAKER
TERMINAL BLOCK POSITIONS 5 & 6
ANDCONNECT ST2 COIL WHEN
ST2 OPTIONIS USED
ANSI STANDARD DHP-VR BREAKER DC CONTROL SCHEMATIC ' 97
11
14
7
51
52
18
23
MUST ADDJ UMPERS
AT SECONDARY TERMINAL BLOCKS
WHENST2 OPTIONIS USED
12
13
NOT AVAILABLE
WHENSPRING
CHARGE INDICATOR
IS USED
M
Y
SR
WL GL RL SPRING
CHARGED
INDICATING
LIGHT
1
2
LS1
bb 3A
1 2
24
CS
C
7
Y LS2
bb
LS2
aa
4
LC
b
21
Y
b
20
5
a
9
16
14
55
CS
T
PR
A
C

S
O
U
R
C
E
52
51
18
54
17
58
15
53 57
a b
NOT AVAILABLE WHEN
ST2 OR UV
OPTION IS CHOSEN.
b
a
13
AC (+)
CAP TRIP DEV
AC (-)
ST
1
a
a
10
9
6
19
6
1
0
U
V
14
9
U
V
11
UV
FOR ACUV
TRIP ONLY
ST
2
UV
9UV
10UV
9A
10A
13
12
52
a
51
OPTIONS
PS1
PS2
bb
5 53
12
6
3
22
b
56
13 55
14
9
20
7 8 10 13
23
REMOVE J UMPER FROM BREAKER
TERMINAL BLOCK POSITIONS 5 & 6
ANDCONNECT ST2 COIL WHEN
ST2 OPTION IS USED
11
14
7
51
18
23
a
52
MUST ADDJ UMPERS
AT SECONDARY TERMINAL BLOCKS
WHEN ST2 OPTION IS USED
ANSI STANDARD SHP-VR BREAKER AC CONTROL SCHEMATIC ' 97
3
7
NOT AVAILABLE
WHEN SPRING
CHARGE INDICATOR
IS USED
CS
C
CS
T
Y ANTI PUMP RELAY
SR SPRING RELEASE COIL (CLOSE COIL)
M SPRING CHARGING MOTOR
ST SHUNT TRIP COIL
PR PROTECTIVE RELAY
SECONDARY DISCONNECT
BKR. CONTROL SWITCH - CLOSE
BKR. CONTROL SWITCH - TRIP
Termi nal Bl ock
or Accessi bl e Termi nal
PS1 Posi ti on Swi tch 1
PS2 Posi ti on Swi tch 2
-
-
-
-
-
-
-
-
-
-
-
LS1
bb
LS2
aa
CLOSED UNTIL SPRINGS
ARE FULLY CHARGED
OPEN UNTIL SPRINGS
ARE FULLY CHARGED
LS2
bb
LC
CLOSED UNTIL SPRINGS
ARE FULLY CHARGED
OPEN UNTIL MECHANISM
IS RESET
PS1 OPEN IN ALL EXCEPT
BETWEEN ' TEST' AND
' CONNECTED' POSITIONS
PS2 CLOSED IN ALL EXCEPT
BETWEEN ' TEST' AND
' CONNECTED' POSITIONS
' C' AND ' NO' BROWN
' C' AND ' NC'
' C' AND ' NO'
' C' AND ' NO'
' C' AND ' NC' BLACK
SWITCH
' C' AND ' NO' BROWN
SWITCH
OPERATION SWITCH TERMINAL
BLACK
I. B. 6513C80C Page 29
Effective 11/97
To engage the secondary contacts on the 5kV. design
while the breaker is in the test position, lift the handle on
the front left hand side of the breaker chassis to a hori-
zontal position. Once the rod is pointing straight out
from the breaker, push it manually to the rear until the
secondaries are initially engaged. At this point, the small
horizontal pin in the handle will have engaged two slots
in the lever, which is pivoted immediately above the
handle. To insure complete secondary engagement,
push down firmly on the curved end of the lever as far
as it will go, using a foot or hand (Figure 4-11). When
using a foot, care should be taken not to bend the lever
by using excessive force.
To engage the secondary contacts on the 7.5 or 15kV.
design while the breaker is in the test position, unlatch
the secondary operating rod, and move it to the left until
it points straight out from the breaker. Push the rod
manually to the rear until the secondaries are initially
engaged. Once initial engagement is achieved, hold the
operating rod firmly in that position with one hand, while
grasping the secondary engaging handle with the other
hand. The secondary engaging handle is located to the
right of the operating rod, just inside a rectangular hole.
By pulling firmly on the engaging handle, complete sec-
ondary engagement will be insured (Figure 4-12).
5-4 INTERLOCKS
NEVER DISABLE OR DEFEAT ANY INTERLOCKS.
HAZARDOUS VOLTAGES WILL CAUSE DEATH,
SEVERE PERSONAL INJURY OR PROPERTY DAM-
AGE.
All DHP-VR breakers are equipped with interlocks that
are compatible with the existing DHP assembly struc-
ture. These interlocks will insure proper and safe break-
er operation.
5-4.1 BREAKER-CELL CODING PLATES
This is a combination of a notched plate in the cell and
interference bars on the breaker, so that only appropri-
ately rated breakers can be put into the cell (Figures
5-10 and 5-11).
5-4.2 LEVERING-IN INTERLOCK
The levering-in interlock is designed to prevent moving
the breaker into or out of the Operating position, if the
!
WARNING
Figure 5-8 Male Secondary Contact Block (In Extended
Position) On 5 kV DHP-VR Breaker
Figure 5-9 Male Secondary Contact Block (In Extended
Position) On 15 kV DHP-VR Breaker
I. B. 6513C80C Page 30
Effective 11/97
breaker contacts are closed. DHP-VR interlocks are
completely compatible with the existing levering screw
located in the existing DHP or DVP assembly structure.
DHP-VR 5kV. breakers utilize a levering-in interlock
design that is very similar to the design used on DHP
breakers. A key, which is spring operated by the closing
and opening action of the breaker, prevents levering of
the breaker, unless the breaker is open. Opening the
breaker removes the key from the levering-in shaft key-
way, and the breaker can be levered.
DHP-VR 7.5 and 15kV. breakers utilize a device that
also prevents levering a breaker with the contacts
closed, but is different in design from the 5kV. breaker.
It consists of a plate supported by a pin between the two
pole shaft levers. As the breaker closes, the plate falls
into the levering-in shaft keyway, by virtue of gravity.
Opening the breaker lifts the plate out of the keyway,
and the breaker can be levered.
5-4.3 ANTI-CLOSE INTERLOCK
This interlock prevents release of the closing springs
electrically or manually, if the breaker is already closed
(Figure 5-6). On a closed breaker, the interlock lever
moves toward the rear. In this position, the movement of
the spring release clapper does not lift the lever, and
thus the spring release latch cannot be moved.
5-4.4 FLOOR TRIPPING AND CLOSING SPRING
RELEASE INTERLOCKS
The floor tripping and closing spring release interlocks
operate to trip the breaker and discharge the closing
spring when the breaker is inserted into the cell to the
test position, or removed from the cell. Cam plates on
the cell floor lift trip levers on the underside of the break-
er to trip the breaker and/or discharge the closing
springs (Figures 5-12 and 5-13).
The floor tripping interlock also operates to hold the
breaker trip-free while it is traveling between the Test
and Connected positions. This is to prevent accidental
closing of the breaker in an intermediate position.
5-4.5 RAIL LATCH
The main function of the rail latch is to prevent damage
to the levering-in screw and nut (Figures 5-14 and 5-15).
It also functions to latch the breaker in the Test position,
as previously described in Section 4-8b.
Figure 5-10 Code Plate Installed On 5 kV DHP-VR
Breaker
Figure 5-11 Code Plate Installed On 15 kV DHP-VR
Breaker
I. B. 6513C80C Page 31
Effective 11/97
Figure 5-12 DHP-VR Breaker (5 kV) Floor Tripping
Levers (Underneath Front View)
Figure 5-13 DHP-VR Breaker (7.5 or 15 kV) Floor
Tripping Lever (Underneath Rear View)
Figure 5-14 DHP-VR Breaker (5 kV) Rail Latch
Figure 5-15 DHP-VR Breaker (7.5 or 15 kV) Rail Latch
Tripping Lever
Spring Release Lever

Tripping Lever
Spring Release Lever

I. B. 6513C80C Page 32
Effective 11/97
5-6 LEVERING DEVICE
The purpose of the levering device is to move the break-
er between the Test and Connected positions. On the
7.5 or 15kV. DHP-VR, the levering-in mechanism is
located in the mechanism, while it is located in the
breaker truck on the 5kV. DHP-VR. The levering nut is
fastened securely to the guide tube and is loosely
retained in a housing fastened to the extreme rear of the
breaker chassis (Figures 5-17 and 5-18).
The operation consists of engaging the rotatable lever-
ing nut on the circuit breaker with the levering screw
mounted on the rear wall of the cell. By traversing the
levering nut along the levering screw, the breaker is
moved between positions within the switchgear housing.
The guide tube is slotted lengthwise for a distance about
equal to the travel distance of the breaker. The levering-
in shaft has two rectangular hardened keys welded to it
which slide in the guide tube slot. Thus, as the levering-
in shaft is rotated, the guide tube and nut also rotate.
As the breaker is levered in by clockwise rotation, the
keys on the levering-in shaft move toward the end of the
guide tube slot. As the rear key comes out of the slot,
the levering-in shaft turns freely and the breaker moves
no further.
5-5 MISCELLANEOUS ITEMS
5-5.1 GROUND CONTACT
The ground contact is an assembly of spring loaded fin-
gers for all DHP-VR breaker designs providing a discon-
nectable means for grounding the breaker chassis, after
it has been inserted into a switchgear cell (Figure 5-16).
The ground contact is located on the underside of the
chassis next to the secondary contact block. An exten-
sion of the switchgear ground bus is secured to the cell
floor in such a position to engage the ground contact
automatically, when the breaker is pushed into the Test
position. It remains engaged in all positions from Test to
and including Connected.
5-5.2 MOC AND TOC SWITCH OPERATIONS
A mechanism attached to the right side of the DHP-VR
breaker engages a channel member of the Mechanism
Operated Cell Switch (MOC) located in the switchgear
cell (Figures 5-14 and 5-15). This mechanism permits
the contacts of the MOC Switch to be correlated with the
breakers contact position.
All 15 kV. Type DHP-VR Breakers utilize the DHP-VR
SURE CLOSE MECHANISM to control MOC velocity
and closely mimic the dynamics and velocities of
older breakers. It is imperative that this mechanism
be adjusted to match the number of MOC switches
(from 0 to 3) mounted in the cell. Always make sure
the mechanism is properly adjusted in keeping with
paragraph 4-2 of this manual before any attempt is
made to insert the breaker into the cell.
In addition, the MOC pantograph must be checked
in keeping with the instructions outlines in para-
graph 4-3 before any attempt is made to insert the
breaker into the cell.
The cell mounted Truck Operated Cell Switch (TOC) is
operated by movement of the breaker truck into or out of
the Connected position.
5-5.3 OPERATIONS COUNTER
All DHP-VR breakers are equipped with a mechanical
operations counter (Figures 3-2 and 3-4). As the break-
er opens, the linkage connected to the pole shaft lever
advances the counter reading by one.
NOTICE
Figure 5-16 DHP-VR Breaker Ground Contact
I. B. 6513C80C Page 33
Effective 11/97
The end of the guide tube is shaped like a steep-pitch
one-turn screw thread so that when the levering shaft is
rotated counter-clockwise, the rear key will catch and
enter the slot and rotate the guide tube and nut, with-
drawing the breaker. At the end of the travel, the nut dis-
engages from the screw and is spin free.
Figure 5-17 DHP-VR Breaker (5 kV) Levering-in Device
Nut Housing
Figure 5-18 DHP-VR Breaker (7.5 and 15 kV) Levering-
in Device Nut Housing
I. B. 6513C80C Page 34
Effective 11/97
SECTION 6: INSPECTION AND
MAINTENANCE
6-1 INTRODUCTION
DO NOT WORK ON A BREAKER IN THE CON-
NECTED POSITION.
DO NOT WORK ON A BREAKER WITH SEC-
ONDARY DISCONNECTS ENGAGED.
DO NOT WORK ON A BREAKER WITH SPRINGS
CHARGED OR CONTACTS CLOSED.
DO NOT DEFEAT ANY SAFETY INTERLOCKS.
DO NOT LEAVE MAINTENANCE TOOL IN THE
SOCKET AFTER CHARGING THE CLOSING
SPRINGS.
DO NOT STAND LESS THAN ONE METER AWAY
FROM THE BREAKER WHEN TESTING FOR VAC-
UUM INTEGRITY.
FAILURE TO FOLLOW ANY OF THESE INSTRUC-
TIONS MAY CAUSE DEATH, SERIOUS BODILY
INJURY, OR PROPERTY DAMAGE. SEE SECTION
2-SAFE PRACTICES FOR MORE INFORMATION.
6-2 FREQUENCY OF INSPECTION
Inspect the breaker once a year when operating in a
clean, non corrosive environment. For a dusty and cor-
rosive environment, inspection should be performed
twice a year. Additionally, it is recommended to inspect
the breaker every time it interrupts fault current.
Refer to the table on following page for maintenance
and inspection check points.
!
WARNING
A
A
View A A
Apply one drop of light
machine oil such as Mobil
One at locations shown.
Figure 6-1 Lubrication Points
I. B. 6513C80C Page 35
Effective 11/97
6-3 INSPECTION AND MAINTENANCE
PROCEDURES
No. /Section
1. Insulation
Insulation
Integrity
2. Power
Elements
3. Control
Circuit
Parts
4. Operating
Mechanism
Inspection Item
Stand off insulators, oper-
ating rods, tie-bars and
barriers
Main Circuit to Ground
Between Main Circuit
Terminals.
Control Circuit to Ground.
Vacuum Interrupters
Primary Disconnects
Closing and tripping devices
including disconnects.
Wiring
Terminals
Motor
Tightness of hardware.
Dust or foreign matter.
Lubrication
Deformation or excessive
wear.
Manual operation.
Criteria
No dirt
No cracking
Withstand 27 kV, 60 Hz
for 1 minute.
Withstand
15 kV, 60 Hz for 1 minute.
(5kV Ratings)
27kV, 60 Hz for 1 minute.
(15kV Ratings)
Withstand 1125 V, 60 Hz
for 1 minute.
Contact Erosion visibility
of mark.
Contact wipe visible.
Adequate Vacuum
Dirt on ceramic body.
No burning or damage
Smooth and correct operation
by control power.
Securely tied in proper place.
Tight
At-5000 Operations
No loose or missing parts.
No dust or foreign matter.
Smooth operation and no
excessive wear.
No excessive deformation
or wear.
Smooth operation.
Inspection Method
Visual check
Visual check
Hipot Tester
Hipot Tester
Hipot Tester
Visual-Close the breaker and
look for green mark on mov-
ing stem from the rear of the
breaker (see Fig. 6.2 and
6.3).
Visual (Fig. 6.4 and 6.5)
See Section 6.4
Visual check
Visual check
Test closing and tripping of
the breaker twice.
Visual check
Visual check
Check Counter
Visual and tightening with
appropriate tools.
Visual check
Sight and feel.
Visual and operational.
Manual charging closing and
tripping.
Corrective Action if Necessary
Clean with lint-free cloth.
Replace cracked unit
Clean and retest or replace.
Clean and retest or replace.
Clean and retest or replace.
If mark is not visible, replace
interrupter assembly.
Replace VI assembly.
Replace interrupter assembly if
vacuum is not adequate.
Clean with dry lint-free cloth.
Replace if burned, damaged or
eroded.
Replace any defective device-
Identify per troubleshooting chart.
Repair or tie as necessary
Tighten or replace if necessary.
Replace brushes.
Tighten or reinstate if necessary.
Clean as necessary.
Lubricate very sparingly with light
machine oil.
Remove cause and replace parts.
Correct per trouble-shooting chart
if necessary.
Bolt Size 8-32 10-32 .25-20 .31-18 .38-16 .50-13
Torque Lb. In. 24 36 72 144 300 540
In this case the equipment must be capable of delivering
5 milliamperes for one minute to avoid ambiguity due to
field emission or leakage currents and the test voltage
shall be as shown in Table 6.1.
The current delivery capability of 25 mA ac and 5 mA dc
apply when all three VIs are tested in parallel. If individ-
ual VIs are tested, current capability may be one third of
these values.
SOME DC HIGH POTENTIAL UNITS, OPERATING AS
UNFILTERED HALF-WAVE RECTIFIERS, ARE NOT
SUITABLE FOR USE TO TEST VACUUM INTER-
RUPTERS BECAUSE THE PEAK VOLTAGE
APPEARING ACROSS THE INTERRUPTERS CAN BE
SUBSTANTIALLY GREATER THAN THE VALUE
READ ON THE METER.
6-5 CONTACT EROSION AND WIPE
Since the contacts are contained inside the interrupter,
they remain clean and require no maintenance.
However, during high current interruptions there may be
a minimal amount of erosion from the contact surfaces.
Maximum permitted erosion is 1/8 inch. To determine
contact erosion, close the breaker and observe the vac-
uum interrupter moving stem from the rear of the break-
er. If the mark on each stem is visible, erosion has not
reached maximum value thus indicating satisfactory
contact surface of the interrupter. If the mark is not visi-
ble, the vacuum interrupter assembly must be replaced
(Figures 6-2 and 6-3).
The adequacy of contact wipe can be determined by
simply observing the vacuum interrupter side of the
operating rod assembly on a closed breaker. Figures
6-4 and 6-5 show the procedure for determining the
contact wipe. If the wipe is not adequate, the vacuum
interrupter assembly (Pole Unit) must be replaced. Field
adjustment is not possible.
Breaker Rated
Vacuum Interrupter Integrity Test Voltage
Maximum Voltage
ac 60 Hz dc
Up to and including
27 kV 40 kV
15.0 kV
I. B. 6513C80C Page 36
Effective 11/97
6-4 VACUUM INTERRUPTER INTEGRITY TEST
Vacuum interrupters used in Type DHP-VR circuit
breakers are highly reliable interrupting elements.
Satisfactory performance of these devices is dependent
upon the integrity of the vacuum in the interrupter and
the internal dielectric strength. Both of these parameters
can be readily checked by a one minute ac high poten-
tial test. (See Table 6.1 for appropriate test voltage.)
During this test, the following warning must be
observed:
APPLYING ABNORMALLY HIGH VOLTAGE ACROSS
A PAIR OF CONTACTS IN VACUUM MAY PRODUCE
X-RADIATION. THE RADIATION MAY INCREASE
WITH THE INCREASE IN VOLTAGE AND/OR
DECREASE IN CONTACT SPACING. X-RADIATION
PRODUCED DURING THIS TEST WITH RECOM-
MENDED VOLTAGE AND NORMAL CONTACT
SPACING IS EXTREMELY LOW AND WELL BELOW
MAXIMUM PERMITTED BY STANDARDS.
HOWEVER, AS A PRECAUTIONARY MEASURE
AGAINST POSSIBILITY OF APPLICATION OF HIGH-
ER THAN RECOMMENDED VOLTAGE AND/OR
BELOW NORMAL CONTACT SPACING, IT IS REC-
OMMENDED THAT ALL OPERATING PERSONNEL
STAND AT LEAST ONE METER AWAY IN FRONT OF
THE BREAKER.
With the breaker open and securely sitting on the floor,
connect all top primary studs (bars) together and the
high potential machine lead. Connect all bottom studs
together and ground them along with the breaker frame.
Start the machine at zero potential, increase to appropri-
ate test voltage and maintain for one minute.
Successful withstand indicates that all interrupters have
satisfactory vacuum level. If there is a breakdown, the
defective interrupter or interrupters should be identified
by an individual test and replaced before placing the
breaker in service.
After the high potential is removed, discharge any elec-
trical charge that may be retained, particularly from the
center shield of vacuum interrupters. To avoid any ambi-
guity in the ac high potential test due to leakage or dis-
placement (capacitive) current, the test unit should have
sufficient volt-ampere capacity. It is recommended that
the equipment be capable of delivering 25 milliamperes
for one minute.
Although an ac high potential test is recommended, a dc
test may be performed if only a dc test unit is available.
!
CAUTION
!
WARNING
Table 6.1
FAILURE TO REPLACE A VACUUM INTERRUPTER
ASSEMBLY WHEN CONTACT EROSION MARK IS
NOT VISIBLE OR WIPE IS UNSATISFACTORY, WILL
CAUSE THE BREAKER TO FAIL TO INTERRUPT
AND THEREBY CAUSE PROPERTY DAMAGE OR
PERSONAL INJURY.
6-6 INSULATION
In DHP-VR breakers, insulation maintenance primarily
consists of keeping all insulating surfaces clean. This
can be done by wiping off all insulating surfaces with a
dry lint free cloth or dry paper towel. In case there is any
tightly adhering dirt that will not come off by wiping, it
can be removed with a mild solvent or distilled water.
But be sure that the surfaces are dry before placing the
breaker in service. If a solvent is required to cut dirt, use
Stoddards Solvent Cutler-Hammer 55812CA or com-
mercial equivalent. Secondary control wiring requires
inspection for tightness of all connections and damage
to insulation.
6-7 INSULATION INTEGRITY CHECK
PRIMARY CIRCUIT:
The integrity of primary insulation may be checked by
the AC high potential test. The test voltage depends
upon the maximum rated voltage of the breaker. For the
breakers rated 4.76 kV, 8.25 kV and 15 kV, the test volt-
ages are 15 kV, 27 kV and 27 kV RMS, 60 Hz respec-
tively. Conduct the test as follows:
Close the breaker. Connect the high potential lead of
the test machine to one of the poles of the breaker.
Connect the remaining poles and breaker frame to
ground. Start the machine with output potential at zero
and increase to the test voltage. Maintain the test volt-
age for one minute. Repeat for the remaining poles.
Successful withstand indicates satisfactory insulation
strength of the primary circuit.
If a DC high potential machine is used, make certain
that the peak voltage does not exceed the peak of the
corresponding AC RMS test voltage.
SECONDARY CIRCUIT:
Isolate the motor by pulling apart the two insulated quick
disconnecting terminals in the two motor leads provided
for this purpose. Connect all points of the secondary dis-
connect pins with a shooting wire. Connect this wire to
the high potential lead of the test machine. Ground the
breaker frame. Starting with zero, increase the voltage
to 1125 RMS, 60 Hz. Maintain the voltage for one
I. B. 6513C80C Page 37
Effective 11/97
Figure 6-2 Vacuum Interrupter Showing Contact
Erosion Indicator With Breaker Open (Shown here for
clarity purposes only)
Figure 6-3 Vacuum Interrupter Showing Contact
Erosion Indicator With Breaker Closed (Indicators are
checked only when breaker is closed)
!
WARNING
I. B. 6513C80C Page 38
Effective 11/97
Figure 6-4 T Contact Wipe Indicator Example with Blue
Spring (if the T or any portion of it is visible as shown with
the breaker closed, the wipe is satisfactory, See Next
Figure for Graphic of All Possibilities)
minute. Successful withstand indicates satisfactory insu-
lation strength of the secondary control circuit. Remove
the shooting wire and reconnect the motor leads.
6-8 PRIMARY CIRCUIT RESISTANCE CHECK
Since the main contacts are inside the vacuum chamber
they remain clean and require no maintenance at any
time. Unlike most typical circuit breaker designs, DHP-
VR breakers do not have sliding contacts at the moving
stem either. Instead they use a highly reliable and
unique flexible clamp design that eliminated the need for
lubrication and inspection for wear.
If desired, the DC resistance of the primary circuit may
be measured as follows: close the breaker, pass at least
100 amps DC current through the breaker. With the low
resistance instrument, measure resistance across the
studs on the breaker side of the disconnects for each
pole. The resistance should not exceed 60, 40, 20
microohms for 1200, 2000, and 3000 amps respectively.
6-9 MECHANISM CHECK
Make a careful visual inspection of the mechanism for
any loose parts such as bolts, nuts, pins, rings, etc.
Check for excessive wear or damage to the breaker
components. Operate the breaker several times manu-
ally and electrically. Check the closing and opening
Figure 6-5 Wipe Indication Procedure (Performed Only
with Breaker Closed)
Any part of Red or Gray Indicator Visible
Wipe Satisfactory
Red or Gray Indicator Not Visible
Wipe Unsatisfactory
Any part of T Shape Indicator Visible
Wipe Satisfactory
T Shape Indicator Not Visible
Wipe Unsatisfactory
WHITE CONTACT SPRINGS
BLUE OR RED
CONTACT SPRINGS
I. B. 6513C80C Page 39
Effective 11/97
times to verify that they are in accordance with the limits
in Table 5.1.
6-10 LUBRICATION
All parts that require lubrication have been lubricated
during the assembly with molybdenum disulphide
grease. Cutler-Hammer M No. 53701QB. Over a period
of time, this lubricant may be pushed out of the way or
degrade. Proper lubrication at regular intervals is essen-
tial for maintaining the reliable performance of the
mechanism. Once a year or every 2000 operations
(1000 operations for 3000 amp breaker) whichever
comes first, the breaker should be relubricated. The
locations shown in Figure 6.1 should be lubricated with
a drop of light machine oil.
After lubrication, operate the breaker several times man-
ually and electrically.
Roller bearings are used on the pole shaft, the cam
shaft, the main link and the motor eccentric. These
bearings are packed at the factory with a top grade slow
oxidizing grease which normally should be effective for
many years. They should not be disturbed unless there
is definite evidence of sluggishness, dirt or parts are dis-
mantled for some reason.
If it becomes necessary to disassemble the mechanism,
the bearings and related parts should be thoroughly
cleaned, remove old grease in a good grease solvent. Do
not use carbon tetrachloride. They should then be washed
in light machine oil until the cleaner is removed. After the
oil has been drawn off, the bearings should be packed
with Cutler-Hammer Grease 53701QB or equivalent.
SYMPTOM
FAILS TO CLOSE
Closing Springs not charged
INSPECTION AREA
Control Circuit
Mechanism
PROBABLE DEFECTS
Control Power
(Fuse blown or switch off)
Secondary Disconnects
Motor Cut-off Switch
(Poor or burned contacts. Lever
not operational.)
Terminals and connectors
(Poor or burned contacts)
Motor
(Brushes worn or commutator
segment open)
Pawls
(Slipping or broken)
Ratchet Wheel
(Teeth worn or broken)
Cam Shaft Assy.
(Sluggish or jammed)
Oscillator
(Reset spring off or broken)
6-11 TROUBLESHOOTING CHART (CONTINUED ON
NEXT PAGE)
I. B. 6513C80C Page 40
Effective 11/97
SYMPTOM
FAILS TO CLOSE
Closing Springs Charged but
breaker does not close
UNDESIRABLY CLOSES
INSPECTION AREA
No Closing Sound
(Close Coil does not pick up)
Closing Sound
But no Close
Control Circuit
Mechanism
PROBABLE DEFECTS
Control Power
(Fuse blown or switch off)
Secondary Disconnects
Anti Pump Relay
(Y relay N.C. contact open or
burned or relay picks up)
Close Coil
(Open or burned)
Latch Check Switch
(Contact open - Bad switch or
trip bar not reset)
Auxiliary Switch
(b contact open or burned)
Motor Cut-off
(Contacts open or burned)
Trip Coil Assy.
(Clapper fails to reset)
Pole Shaft
(Not open fully)
Trip Latch Reset Spring
(Damaged or missing)
Trip Bar-D Shaft
(Fails to remain reset)
Trip Latch-Hatchet
(Fails to remain reset)
Trip Floor Tripper
(Fails to remain reset)
Close Latch
(Binding)
Close Latch Roller
(Binding)
Trip Circuit Energized
Close Circuit
(CS/C Getting shorted)
Close Release Latch
(Fails to reset)
Close Floor Tripper
(Fails to reset)
I. B. 6513C80C Page 41
Effective 11/97
SYMPTOM
FAILS TO TRIP
No Trip Sound
Trip Sound
But no Trip
UNDESIRABLY TRIPS
INSPECTION AREA
Control Circuit
Trip Mechanism
Trip Mechanism
Vacuum Interrupter
(One or more Welded)
Control Circuit
Mechanism
PROBABLE DEFECTS
Control Power
(Fuse blown or switch off)
Secondary Disconnect
Auxiliary Switch
(a contact not making poor or
burned)
Trip Coil
(Burned or open)
Terminals and Connections
(Poor or burned or open)
Trip Clapper
(J ammed)
Trip Bar, Trip Latch
(J ammed)
Pole Shaft
(J ammed)
Operating Rod Assembly
(Broken or pins out)
Control Power
(CS/T Switch, remains made)
Trip Coil Clapper
(Not resetting)
Trip Bar or Trip Latch
(Poor engagement of mating or
worn surfaces)
Trip Bar Reset Sprint
(Loss of torque)
I. B. 6513C80C Page 42
Effective 11/97
SECTION 7: RENEWAL PARTS
7-1 GENERAL
In order to minimize production downtime, it is recom-
mended that an adequate quantity of spare parts be
carried in stock. The quantity will vary from customer
to customer, depending upon the service severity and
continuity requirements. Each customer should devel-
op his own stock level based on operating experience.
7-1.1 ORDERING INSTRUCTIONS
a. Always specify the breaker rating information and
shop order number.
b. Describe the item, give the style number, and specify
the quantity required.
c. Specify the voltage for electrical components.
d. Specify the method of shipping desired.
e. Send all orders or correspondence to the nearest
Cutler-Hammer sales office.
I. B. 6513C80C
Effective 11/97
Style 6513C80C
Printed in U.S.A.
This instruction booklet is published solely for informa-
tion purposes and should not be considered all inclu-
sive. If further information is required, you should con-
sult Cutler-Hammer.
Sale of product shown in this literature is subject to
terms and conditions outlined in appropriate Cutler-
Hammer selling policies or other contractual agreement
between the parties. This literature is not intended to
and does not enlarge or add to any such contract. The
sole source governing the rights and remedies of any
purchaser of this equipment is the contract between the
purchaser and Cutler-Hammer.
NO WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING WARRANTIES OF FITNESS FOR A PAR-
TICULAR PURPOSE OR MERCHANTABILITY, OR
WARRANTIES ARISING FROM COURSE OF DEAL-
ING OR USAGE OF TRADE, ARE MADE REGARDING
THE INFORMATION, RECOMMENDATIONS AND
DESCRIPTIONS CONTAINED HEREIN. In no event
will Cutler-Hammer be responsible to the purchaser or
user in contract, in tort (including negligence), strict lia-
bility or otherwise for any special, indirect, incidental or
consequential damage or loss whatsoever, including but
not limited to damage or loss of use of equipment, plant
or power system, cost of capital, loss of power, addition-
al expenses in the use of existing power facilities, or
claims against the purchaser or user by its customers
resulting from the use of the information, recommenda-
tions and description contained herein.
Cutler-Hammer
Five Parkway Center
Pittsburgh, PA 15220

You might also like