Scribd Logo
Upload

Welcome to Scribd!

  • 671 views

    Turbovisory System

    Uploaded by

    Lily Sharma
    The Turbovisory system monitors three things on thermal turbines: eccentricity using eddy current sensors to measure shaft movement, turbine speed using a toothed wheel and magnetic probe, and speeder gear position using potentiometers. It provides critical information to safely operate and load large turbines by interpreting measurements of shaft alignment, rotational speed, and control mechanisms. This helps minimize the time to start up and load the plant while maintaining safe operation given the small clearances needed for high efficiency.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOCX, PDF, TXT or read online from Scribd

    Turbovisory System

    Uploaded by

    Lily Sharma
    671 views2 pages
    The Turbovisory system monitors three things on thermal turbines: eccentricity using eddy current sensors to measure shaft movement, turbine speed using a toothed wheel and magnetic probe, and speeder gear position using potentiometers. It provides critical information to safely operate and load large turbines by interpreting measurements of shaft alignment, rotational speed, and control mechanisms. This helps minimize the time to start up and load the plant while maintaining safe operation given the small clearances needed for high efficiency.

    Original Description:

    research

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The Turbovisory system monitors three things on thermal turbines: eccentricity using eddy current sensors to measure shaft movement, turbine speed using a toothed wheel and magnetic probe, and speeder gear position using potentiometers. It provides critical information to safely operate and load large turbines by interpreting measurements of shaft alignment, rotational speed, and control mechanisms. This helps minimize the time to start up and load the plant while maintaining safe operation given the small clearances needed for high efficiency.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    671 views2 pages

    Turbovisory System

    Uploaded by

    Lily Sharma
    The Turbovisory system monitors three things on thermal turbines: eccentricity using eddy current sensors to measure shaft movement, turbine speed using a toothed wheel and magnetic probe, and speeder gear position using potentiometers. It provides critical information to safely operate and load large turbines by interpreting measurements of shaft alignment, rotational speed, and control mechanisms. This helps minimize the time to start up and load the plant while maintaining safe operation given the small clearances needed for high efficiency.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 2

    TURBOVISORY SYSTEM

    Introduction: Mass of the Thermal turbine is very huge and when operating a machine of this size with the small clearences required to achieve high plant efficiency. The correct interpretation of the information provided allows the plant to be run up and loaded in the minimum time consistent with safe operation. It is the purpose of the turbine supervisory equipment to provide this information. The measurements covered by the Turbovisory system include: 1.) Eccentricity 2.) Turbine Speed. 3.) Speeder gear Position. Eccentricity: It is defined as the out of centre excursion of the axis of rotation of shaft. It is normally measured as the diameter of the locus, traced out by the shaft centre. For practical reasons, the measurement is made on the shaft, within the bearing pedestal. The change in radial air gap within the cylinder is inferred from this measurement. Eddy Current Measurement System: The system for measuring the eccentricity, consists of a transducer that operates on Eddy current principle. The tip of the transducer contains a coil of wire, which is connected to the signal sensor. The signal sensor contains an oscillator circuit, a detector or a demodulator circuit. In this system, the transducer coil and connecting cable form a part of the oscillator circuit which generates a high frequency current in the measurement coil, at a frequency of 1 or 2MHz. This current produces a magnetic field around the pickup coil and the turbine shaft that brought into the proximity of the coil links with the magnetic flux, producing eddy currents in the conducting material. These eddy currents alter the operating point of the oscillator, modifying the amplitude of the signal, proportional to the gap between pickup coil and shaft.

    The average voltage is used to indicate gap from the transducer tip. The varying voltage is the AC vibration signal. The slope of the curve, showing the change in the transducer output voltage as the gap changes is the sensitivity of the system (2V/mm).

    Speed measuring through Toothed wheel and probe: Of the variety of the speed detection methods, the toothed wheel, and magnetic probe is probably the most useful choice. It is difficult to design toothed wheel systems which will inherently produce an accurate sinusoidal output. In practice they normally produce output pulses of which, only the leading edge is significant. No information is transmitted except at the instant that the pulses occur which need a high pulse repetition rate, if good stability is required. In general, the angular machining accuracy of the teeth and mounting eccentricity of the wheel on the shaft will be independent of the number of teeth. A probe system producing substantially a square wave output is usually desirable. It must be suitable for use where a relatively large air gap exists between probe tip and toothed wheel, which will accommodate the varying hydrodynamic conditions in the bearings.

    Speeder gear Position: Wire wound potentiometers are used for the measurement of speeder gear position and this is transmited to the control room by electronic system.

    You might also like