SERVICE MANUAL

MODEL 8210 SWEEP/FUNCTION GENERATOR

DAGATRONICS CORPORATION

CONTENTS

1. PERFORMANCE CHECK

PROCEDURE

2. ADJUSTMENT PROCEDURE 3. TROUBLESHOOTING PROCEDURE 4. PARTS LIST 5. CIRCUIT DIAGRAM

1. PERFORMANCE CHECK PROCEDURE

1-1. General This section contains the Procedures required to check and maintain specified instrument performance. The adjustments should be performed at an ambient temperature of 23C 5C and a relative humidity of less than 60%. It allows the instrument to stabilize at this environment for a minimum of 30 minutes.

1-2. Equipment's required Table 1-1 is shown test equipment's required. Table 1-1 Equipment's required No . 1. 2. 3. 4. 5. 6. 7. Equipment name Frequency Counter Oscilloscope AC Millivolt Meter Distortion Analyzer DC Power Supply Signal Generator FEEDTHROUGH TERMINATION 50 Specification DC to 60 MHz DC to 20 MHz Up to 30 Vrms 0.01% 100kHz DC 0 to 10V 200mHz to 110 MHz Remark

1-3. Performance check 1-3-1. OUTPUT FREQUENCY RANGE SPECIFICATION 0.1 Hz TO 10 MHz ACCURACY +/- 5 % OF SETTING EQUIPMENT FREQUENCY COUNTER BNC CABLE FEEDTHROUGH TERMINATION 50 (if necessary) PROCEDURE 2. Set 8210 as follows; - Function ; SINE WAVE (

)
3

- ATT ; 0 dB(PULL OUT) - AMPLITUDE ; CENTER - COUNT ; INT(PULL OUT) - DC OFFSET ; OFF(PUSH IN) - SYM ; OFF(PUSH IN) - SWEEP ; OFF(PUSH IN) 2. Connect the frequency counter to output terminal. 3. Set the frequency counter to frequency measurement. 4. Set the output frequency of this product by FREQUENCY RANGE and DIAL and verify counter frequency reading as follows; 8210 setting Range 1M 100k 10k 1k 100 10 1 Frequency 10.000 MHz 100.00 kHz 1.0000 MHz 10.000 kHz 100.00 kHz 1.0000 kHz 10.000 kHz 100.00 Hz 1.0000 kHz 10.000 Hz 100.00 Hz 1.0000 Hz 10.000 Hz 100.00 mHz Counter reading

** For reading less than 200 mHz, you can read by period value. 200mHz ; 5.000 sec 100 mHz ; 10.000 sec 1-3-2. AMPLITUDE AND ATTENUATION SPECIFICATION Amplitude range ;100mVp-p to 10Vp-p IN TO 50 Attenuation ;20 dB ACCURACY Lower than 100mVp-p(IN TO 50) at MIN. Higher than 10Vp-p(IN TO 50) at MAX.
4

EQUIPMENT Oscilloscope AC Millivoltmeter BNC CABLE FEEDTHROUGH TERMINATION 50 PROCEDURE 1. Set this product as follows; - Function ; SINE WAVE ( ) - ATT ; 0 dB(PULL OUT) - AMPLITUDE ; CENTER - COUNT ; INT(PULL OUT) - DC OFFSET ; OFF(PUSH IN) - SYM ; OFF(PUSH IN) - SWEEP ; OFF(PUSH IN) 2. Connect the oscilloscope through FEEDTHROUGH TERMINATION 50 to output terminal. 3. Set Amplitude Control to Min. position and check the output level is lower than 100mVp-p(less 5div in 20mV/div). 4. Set Amplitude Control to Max. position and check the output level is higher than 10Vp-p(higher than 4div in 5V/div). 5. Set Amplitude Control to Min. position and connect AC Millivoltmeter to output terminal. 6. Set the Range of AC millivoltmeter to 3V range and adjust Amplitude control for 0dB reading on AC millivoltmeter. 7. Push in 20dB ATT switch and check the reading of AC Millivoltmeter is -20 dB. 1-3-3. SINE WAVE CHARACTERISTICS SPECIFICATION Total harmonic Distortion(THD) ; 1 % (10Hz to 100kHz) EQUIPMENT Distortion analyzer BNC CABLE FEEDTHROUGH TERMINATION 50 (if necessary) PROCEDURE 1. Set this product as follows; - Function ; SINE WAVE ( ) - ATT ; 0 dB(PULL OUT) - AMPLITUDE ; CENTER
5

- COUNT ; INT(PULL OUT) - DC OFFSET ; OFF(PUSH IN) - SYM ; OFF(PUSH IN) - SWEEP ; OFF(PUSH IN) 2. Connect the distortion analyzer to output terminal. 3. Check the distortions of output signal are less than 1% from 10Hz to 100kHz. 1-3-4. TRIANGLE/SQUARE WAVE CHARACTERISTICS SPECIFICATION Linearity of Triangle Wave ; 99 % (10Hz to 100kHz) Rise and Fall Time of Square Wave ; Less than 120nS at 10MHz Max. output level EQUIPMENT Oscilloscope BNC CABLE FEEDTHROUGH TERMINATION 50 (if necessary) PROCEDURE 1. Set this product as follows; - Function ; TRIANGLE WAVE ( ) - ATT ; 0 dB(PULL OUT) - AMPLITUDE ; CENTER - COUNT ; INT(PULL OUT) - DC OFFSET ; OFF(PUSH IN) - SYM ; OFF(PUSH IN) - SWEEP ; OFF(PUSH IN) 2. Connect the oscilloscope to output terminal. 3. Check the linearity of Triangle wave from 10Hz to 100kHz. 4. Change the function to SQUARE WAVE( ) and check the rise and fall time at 10MHz Max. output level. 1-3-5. TTL OUTPUT SPECIFICATION TTL OUTPUT - Rise and Fall Time ; Less than 25nS - Output Level ; TTL LEVEL (H 2.4V , L 0.4V) EQUIPMENT Oscilloscope BNC CABLE

PROCEDURE 1. Set this product as follows; - FREQ. RANGE ; 10k - FREQ. DIAL ; 10kHz - COUNT ; INT(PULL OUT) - DC OFFSET ; OFF(PUSH IN) - SYM ; OFF(PUSH IN) - SWEEP ; OFF(PUSH IN) 3. Set the oscilloscope to 1V/div, 5uS/div and connect to TTL output terminal. 4. Check the rise and fall time of TTL SQUARE WAVE on CRT( 5div ). 1-3-5. DC OFFSET CONTROL SPECIFICATION MIN. ; lower than -10 V DC (Open circuit) MAX. ; higher than +10 V DC (Open circuit) EQUIPMENT Oscilloscope BNC CABLE PROCEDURE 1. Set this product as follows; - Function ; SQUARE ( ) - ATT ; 0 dB(PULL OUT) - FREQ. RANGE ; 10k - FREQ. DIAL ; 10kHz - AMPLITUDE ; CENTER 2. Set Oscilloscope to 5V/DIV, 10uS/DIV, DC Coupling and connect to output terminal. 3. Adjust Amplitude Control for 2DIV on CRT. 4. Pull out DC OFFSET Control and set to MIN. position and check the DC OFFSET level is lower than -10V(Lower than -2DIV). 5. Set DC OFFSET Control to MAX. position and check the DC OFFSET level is higher than +10V(Higher than +2DIV). 1-3-6. SYMMETRY CONTROL SPECIFICATION MIN. ; lower than 1:10 MAX. ; higher than 10:1

EQUIPMENT Oscilloscope BNC CABLE FEEDTHROUGH TERMINATION 50 (if necessary) PROCEDURE 1. Set this product as follows; - Function ; SQUARE ( ) - ATT ; 0 dB(PULL OUT) - AMPLITUDE ; CENTER - COUNT ; INT(PULL OUT) - DC OFFSET ; OFF(PUSH IN) - SYM ; OFF(PUSH IN) - SWEEP ; OFF(PUSH IN) 2. Connect the oscilloscope to output terminal. 3. Set the output frequency to 10kHz. 4. Pull out SYM Control and adjust to Min. position. And check the symmetry(duty ratio) is lower than 1:10. 5. Adjust SYM Control to Max. position and check the symmetry(duty ratio) ishigher than 10:1. 1-3-7. SWEEP FUNCTION SPECIFICATION Sweep Width ; 1:1 to 100:1 Sweep Rate ; 0.5Hz to 50Hz(20mS to 2 S) EQUIPMENT Oscilloscope Frequency Counter BNC CABLE FEEDTHROUGH TERMINATION 50 (if necessary) PROCEDURE 1. Set this product as follows; - Function ; SINE WAVE ( ) - ATT ; 0 dB(PULL OUT) - AMPLITUDE ; CENTER - COUNT ; INT(PULL OUT) - DC OFFSET ; OFF(PUSH IN) - SYM ; OFF(PUSH IN) 2. Connect the oscilloscope and Frequency Counter to output terminal. 3. Set Freq. Range to 10k and adjust Freq. Dial to 1.00 kHz (Start Frequency).
8

4. Pull out SWIDTH Control and adjust to max. position ( 100kHz, Stop frequency). 5. Adjust Sweep Rate Control for desired rate and check sweep operating. 1-3-8. VCF IN FUNCTION SPECIFICATION Out-put frequency should be changed from minimum frequency to maximum frequency in each frequency range by changing VCF INPUT Voltage from 0 to 10V DC. EQUIPMENT Power supply BNC CABLE PROCEDURE 1. Set this product as follows; - Function ; SINE WAVE ( ) - Frequency Range ; 10K - Frequency Control ; Max. - ATT ; 0 dB(PULL OUT) - AMPLITUDE ; CENTER - COUNT ; INT(PULL OUT) - DC OFFSET ; OFF(PUSH IN) - SYM ; OFF(PUSH IN) 2. Set Power Supply to 0V and connect to VCF IN Terminal. 3. Check the output frequency is 1.00kHz 0.2kHz. 4. Increase the output voltage of Power Supply up to +10V and check the output frequency as following table. VCF Voltage 0 2.000 V 4.000 V 6.000 V 8.000 V 10.00 V 1-3-9. FREQUENCY COUNTER SPECIFICATION Frequency range ; 200mHz to 110MHz Input sensitivity ; 100mVrms EQUIPMENT Signal generator
9

Output Frequency 1.000 kHz 20.00 kHz 40.00 kHz 60.00 kHz 80.00 kHz 100.00 kHz

Tolerance 0.2kHz 4 kHz 8 kHz 12 kHz 16 kHz 20 kHz

PROCEDURE 1. Set the COUNT to EXT(PUSH IN). 2. Connect the signal generator to EXT COUNT IN terminal. 3. Set the signal generator to 100mVrms, 200mHz and check the reading of 8210. 4. Vary the output frequency from 200mHz to 110MHz and check the 8210 displays correct frequencies. 5. Push in LPF(Low Pass Filter) and check the LPF is working (-3dB +/-0.2dB point at approx. 120kHz). < Check procedure > a. Apply 120KHz signal with minimum input level into EXT COUNT IN. b. Push in LPF switch and check gate time(Frequency display) is stopped. c. Increase input level and check the gate time(Frequency display) is starting to and check the input level is increased about 3dB(+/-0.2dB) from minimum input level. 2. ADJUSTMENT PROCEDURE 2-1. Preliminary Set-up Remove top cover. Apply power, and allow at least 30 minutes for warm-up. 2-2. Power supply a. Check the voltage in each position according to table 2-1. Table 2-1 Power supply outputs Check position Output Pin of U6,15,20 Output Pin of U5 Output Pin of U7 Anode of ZD1 Upper leg of R68 Supplying Voltage + 5 V + 15 V - 15 V - 5 V + 21 V Tolerance 0.5V 0.5V 0.5V 0.5V 2 V Remark U6,15 : Assembled at Rear panel

10

2-4. PRE-ADJUSTMENTS EQUIPMENT Oscilloscope BNC CABLE FEEDTHROUGH TERMINATION 50 (if necessary) PROCEDURE 2-4-1. TRIANGLE WAVE OFFSET 1. Set this product as follows; - Function ; TRIANGLE WAVE ( - ATT ; 20 dB(PUSH IN) - AMPLITUDE ; MIN. - FREQUENCY ; 10kHz - COUNT ; INT(PULL OUT)

- DC OFFSET ; OFF(PUSH IN) - SYM ; OFF(PUSH IN) 2. Set the oscilloscope to 0.5V/DIV, 20uS/DIV , DC Coupling and set the vertical position to horizontal graticule center. 3. Connect the oscilloscope to output terminal. 4. Set AMPLITUDE control for 2DIV on CRT and adjust SFR15(OFFSET ADJUSTER) for 0 OFFSET of waveform(The waveform should be in center. +/- 0.1DIV from horizontal graticule center). 2-4-2.SQUARE WAVE LEVEL 1. Set this product as follows; - Function ; SQUARE WAVE ( - ATT ; 0 dB(PULL OUT) - AMPLITUDE ; MAX. - FREQUENCY ; 10kHz - COUNT ; INT(PULL OUT) - DC OFFSET ; OFF(PUSH IN) - SYM ; OFF(PUSH IN)

2. Change the function to SQUARE WAVE 3. Set the oscilloscope to 5V/DIV, 20uS/DIV 4. Check the output level of Square Wave is

more than 17Vpp.

11

2-4-3.SINE WAVE LEVEL Adjust. 1. Set this product as follows; Function ; SINE WAVE ( ATT ; 0 dB(PULL OUT) AMPLITUDE ; MAX. FREQUENCY ; 10kHz COUNT ; INT(PULL OUT) DC OFFSET ; OFF(PUSH IN) SYM ; OFF(PUSH IN)

2. Change the function to SINE WAVE 3. Set the oscilloscope to 5V/DIV, 20uS/DIV 4. Adjust SFR10 , SFR13 for displaying 4DIV on CRT. (SFR10 : + DIV from horizontal graticule center for up-side of waveform , SFR13 : - DIV from horizontal graticule center for down-side of waveform.

2-4-4. SINE WAVE DISTORTION ADJUST EQUIPMENT Distortion Analyzer BNC CABLE FEEDTHROUGH TERMINATION 50 (if necessary) PROCEDURE 1. Set this product as follows; - Function ; SINE WAVE ( ) - ATT ; 0 dB(PULL OUT) - AMPLITUDE ; Max. - FREQUENCY ; 10kHz 2. Connect Distortion analyzer to Output terminal. 3. Adjust SFR8, SFR11, SFR12 for minimum distortion reading on Distortion analyzer. (less than 0.5 %)

12

2-4-5. AMPLITUDE CONTROL AND ATTENUATOR CHECK EQUIPMENT Oscilloscope AC Millivoltmeter BNC CABLE FEEDTHROUGH TERMINATION 50 PROCEDURE 1. Set this product as follows ; - Function ; SINE WAVE ( ) - ATT ; 0 dB(PULL OUT)) - AMPLITUDE ; CENTER - COUNT ; INT(PULL OUT) - DC OFFSET ; OFF(PUSH IN) - SYM ; OFF(PUSH IN) 2. 3. 4. 5. 6. 7. 8. - SWEEP ; OFF(PUSH IN) Connect the oscilloscope through FEEDTHROUGH TERMINATION 50 to output terminal. Set Amplitude Control to Min. position and check the output level is lower than 1Vp-p(less 5div in 200mV/div). Set Amplitude Control to Max. position and check the output level is higher than 10Vp-p(higher than 4div in 5V/div). Set Amplitude Control to Min. position and connect AC Millivoltmeter to output terminal. Set the Range of AC millivoltmeter to 3V range and adjust Amplitude control for 0dB reading on AC millivoltmeter. Push in 20dB ATT switch and check the reading of AC Millivoltmeter is -20 dB. Check the amplitude of TRIANGLE & SQUARE WAVE same as paragraph 3 to 7.

2-5. FREQUENCY RANGE ADJUSTMENT EQUIPMENT Frequency Counter BNC CABLE FEEDTHROUGH TERMINATION 50 PROCEDURE 1. Set this product as follows; - Function ; TRIANGLE WAVE ( - ATT ; 20 dB(PULL OUT) - AMPLITUDE ; CENTER - COUNT ; INT(PULL OUT) - DC OFFSET ; OFF(PUSH IN)

13

2. 2. 3. 4. 5. 6. 7. 8.

- SYM ; OFF(PUSH IN) - SWEEP ; OFF(PUSH IN) Connect the Frequency Counter to Output Terminal. Set Frequency Range to 1M and Frequency Control(Dial) to MAX. Position. Adjust SFR1 for 10.500 MHz frequency reading on counter. Change Frequency Range to 100k and adjust SFR2 for 1.0500 MHz frequency reading on counter. Change Frequency Range to 10k and adjust SFR3 for 105.00 kHz frequency reading on counter. Change Frequency Range to 1k and adjust SFR4 for 10.50 kHz frequency reading on counter. Change Frequency Range to 100 and adjust SFR5 for 1.050 kHz frequency reading on counter. Change the frequency range to 10 and 1, and check the frequency reading in each range. (10 : 105.00 Hz , 1 : 10.500Hz)

9. After adjustment, check the frequency Control(Dial) at MIN. and MAX. as following table. 8210 setting Range Frequency Control 1M MIN. MAX. 100k MIN. MAX. 10k MIN. MAX. 1k MIN. MAX. 100 MIN. MAX. 10 MIN. MAX. 1 MIN. MAX. Tolerance Less than 100.0 kHz Higher than 10.5 MHz Less than 10.0 kHz Higher than 1.05 MHz Less than 1.0 kHz Higher than 100.5 kHz Less than 100 Hz Higher than 10.5 kHz Less than 10.0 Hz Higher than 1.0 kHz Less than 1 Hz Higher than 100 Hz Less than 100 mHz Higher than 10 Hz

2-6. SYMMETRY ADJUST EQUIPMENT Oscilloscope BNC CABLE FEEDTHROUGH TERMINATION 50 (if necessary) PROCEDURE 1. Set this product as follows; - Function ; SQUARE ( )
14

- ATT ; 0 dB(PULL OUT) - AMPLITUDE ; CENTER - COUNT ; INT(PULL OUT) - DC OFFSET ; OFF(PUSH IN) - SYM ; OFF(PUSH IN) - SWEEP ; OFF(PUSH IN) 2. Connect the oscilloscope to output terminal. 3. Set the output frequency to 100kHz. 4. Pull out SYM Control and adjust to Min. position. And adjust SFR6 the symmetry(duty ratio) is lower than 1:10. 5. Adjust SYM Control to Max. position and adjust SFR7 the symmetry(duty ratio) ishigher than 10:1. 2-7. FREQUENCY COUNTER ADJUST EQUIPMENT 10MHz Standard Signal Source Signal Generator up to 110MHz BNC CABLE FEEDTHROUGH TERMINATION 50 (if necessary) PROCEDURE 1. Set this product as follows; - COUNT ; EXT(PUSH IN) 2. Connect 10MHz Standard Signal to the EXT COUNT IN terminal and adjust TC1 for 10.0000 MHz reading on Counter Display. 3. Set Signal generator to 110MHz, 100mVrms and connect the EXT COUNT IN terminal. 4. Adjust SFR16 (Shield Box IN) for 110.0000 MHz reading on Counter Display. Reduce the output level of Signal Generator Slowly and adjust SFR16 for Minimum input sensitivity(as possible as less than 100mVrms). 5. Change the out frequency of Signal Generator from 110MHz to 200mHz and check the minimum input voltage is less than 100mVrms. 6. Push in LPF(Low Pass Filter) and check the LPF is working (-3dB +/-0.2dB point at approx. 120kHz). < Check procedure > a. Apply 120KHz signal with minimum input level into EXT COUNT IN. b. Push in LPF switch and check gate time(Frequency display) is stopped. c. Increase input level and check the gate time(Frequency display) is starting to and check the input level is increased about 3dB(+/-0.2dB) from minimum input level.
15

3. Troubleshooting Procedure
3-1. Troubleshooting techniques 3-1-1. Check the function selector and switch setting. Incorrect switch settings can give a false indication of instrument malfunction. If there is any question about the correct function or operation, refer to OPERATOR'S MANUAL. 3-1-2. Check associated equipments before proceeding, ensure that any equipments used with this product is operating correctly and verify that out and input signals are properly connected and that the interconnecting cables are not defective. 3-1-3. Visual Check Look for broken terminals, damaged components, mounting status of components, damaged circuit boards, or other clues to the cause of a malfunction. 3-2. Troubleshooting procedure 3-2-1. NO Display 1. Check the FUSE and if it is broken, change to new one with same rating. 2. Check the output voltage of power transformer. -. 17 to 18 Vac between pin 1 and 2 of CN14, and between pin 2 and 3 of CN14 on main board. -. 8 to 10 Vac between pin 1 and 2 of CN4,CN24, and between pin 2 and 3 of CN4,CN24 on main board. 3. Check the DC Power Voltage. -. +5VDC at U6 and U15 output(U6,15 Assembled at rear panel) 4. Check the frequency at pin 19 of U12. It should be 10MHz. 5. Check the connector cable from CN12,CN13(main board) to display board. 3-2-2. Triangle Wave Out-put 1. Check the Function switch operation and select Triangle Wave. 2. Check the DC Power Voltage for Generator Circuit. -. +15VDC at U5 output -. +5VDC at U6,U15,U20 output ( U6,15 :assembled at rear panel) -. -5VDC at Anode of ZD1. -. -15VDC at U7 output -. +21VDC at upper leg of R68 3. Check the waveform at Q7 Emitter. The Triangle Wave should be appeared. 4. If not, check the operation of Amplifier and Triangle oscillator (U1 A/B/D, U2 A/B, Q1,Q2,Q3,Q4,Q5,Q6,D1,D2,D3,D5,Q7). 16

5. Check the Range Selector Switch operation and Frequency Control Volume and Cable connection from VR1 to CN2(Main Board). 6. Check the Amplitude VR4 and Cable connection from VR to CN5 on main board. 7. Check the waveform at R46. The Triangle Wave should be appeared. 8. If not, check the operation of Differential Amplifier(Q12,Q13,Q14,Q15,Q16). 9. Check the Attenuator switch(20 dB) and cable connection from CN7 to Output terminal. 3-2-3. Square Wave Out-put 1. Check the Function switch operation and select Square Wave. 2. Check the waveform at D1(of DD1) Cathode. The Triangle Wave should be appeared. 3. Check the waveform at D2(of DD1) Cathode. The Square Wave should be appeared. 4. If not, check the step 3-2-2. 4 and 5. 5. Check the waveform at 9pin of U3. The Square Wave should be appeared. 6. If not, check the operation of U3. 6. Check the waveform at R45. The Square Wave should be appeared. 7. If not, check the step 3-2-2. 8 and 9. 3-2-4. Sine Wave Out-put 1. Check the Function switch operation and select Sine Wave. 2. Check the waveform at Q7 Emitter. The Triangle Wave should be appeared. 3. If not, check the step 3-2-2. 4 and 5. 4. Check the waveform at Q11 Collector. The Sine Wave should be appeared. 5. If not, check the operation of Sine Shaper(Q8,Q9,Q10,Q11). 6. Check the waveform at R45. The Sine Wave should be appeared. 7. If not, check the step 3-2-2. 8 and 9. 3-2-5. TTL Output 1. Check the connection of cable for TTL Output terminal and Control Volume. 2. Check the waveform at Pin 9 of U3. The Square Wave should be appeared. 3. If not, check the step 3-2-3. 4. Check the waveform at pin 6 of U4. The TTL Level Square Wave should be appeared. 5. If not, check the operation of U4. 3-2-6. Sweep Operation(Width and Rate) 1. Check the cable connection(CN8,CN9) for Width and Rate Control Volume. 2. Vary the Width volumeand check the level of Pulse at pin 7 of U2 is varied. 3. Vary the Rate volume and check the period of Pulse at pin 14 of U2 is varied. 4. If not, check the operation of U2 C/D , D9 and Q17.

17

3-2-7. Frequency Range and Frequency Dial 1. Check the cable connection from CN2(Main Board) to Frequency Control Volume. 2. Check the operation of Range selector switch(Key Switch operation). 3-2-8. Attenuator(20dB) 1. Check the operation of each Attenuator switch. 2. If not working, check the R146,147,148 3-2-9. Frequency Counter(INT/EXT) 1. Check the INT/EXT selector switch operation and set to INT. 2. Check the output frequency at Output terminal by using Frequency counter and check the frequency at R83 is same with output frequency. 3. Check the frequency of reference signal at pin18 and 19 of U12. It should be 10.000MHz. 4. If not, check Reference Oscillator(X1,T1,C54,). 5. Check the frequency at pin3 of U9 and pin 7of U18. It should be same as output frequency. 6. If not, check the operation of Input Amplifier and Devider(Q18,Q19,U8,Q20,Q21,U18). 7. Check the cable connection between CN12(main board) and CN13(Display Board). 8. Check the operation of Counter Circuit, Micro-processor(U12), Driver(U4,5),

Scanner(U10,11) 9. Check the operation of Display Controller(U13,U14,Q22-28) on Display Board.

10. Check LPF function as follows; a. Check the status of LPF S/W(push in) b. Check the voltage at the left leg of R108. It should be around +5V. c. Check the voltage at the anode of D16. It should be around 1.4-1.5V. d. Check the voltage at cathode of D16. It should be around on 0.7-0.8V.

18

4. PARTS LIST
4-1.. Main PCB Parts List

Part Name CER.CAPACITOR CER.CAPACITOR.SMD CER.CAPACITOR.SMD CER.CAPACITOR.SMD CER.CAPACITOR.SMD CER.CAPACITOR.SMD CER.CAPACITOR.SMD CER.CAPACITOR.SMD CER.CAPACITOR.SMD CER.CAPACITOR.SMD CER.CAPACITOR.SMD CER.CAPACITOR.SMD CER.CAPACITOR.SMD CER.CAPACITOR.SMD TRIMMER CAPACITOR MICA CAPACITOR MICA CAPACITOR M/F.CAPACITOR M/F CAPACITOR(BOX) M/F CAPACITOR(BOX) M/F CAPACITOR(BOX) MYLER CAPACITOR ELEC.CAPACITOR ELEC.CAPACITOR ELEC.CAPACITOR ELEC.CAPACITOR ELEC.CAPACITOR ELEC.CAPACITOR ELEC.CAPACITOR ELEC.CAPACITOR SWITCHING DIODE.SMD SWITCHING DIODE.SMD

Specification 0.01uF50V(10nF) 3pF 15pF50V 22pF50V 30pF50V 33pF50V 50pF50V 0.01uF50V(10nF) 0.1uF50V(100nF) 130pF50V 150pF50V 1.5pF50V 470pF50V 4700pF50V(4.7nF) CTC05F500,50pF/2READ 33pF/63V 680pF/63V 0.47uF250V 0.0068uF/63V(6.8nF) 0.068uF/63V(68nF) 0.68uF63V(680nF) 0.22uF100V(220nF) 10uF35V 22uF16V 47uF35V 100uF25V 1000uF35V 220uF35V 2200uF35V 470uF25V 1N4148 HSMS-2825-TR1

q"ty 2.00 C100,101 1.00 C72 1.00 C9 1.00 C87 2.00 C54,C84 1.00 C82 2.00 C01,C02

Referance.

12.00 C2,8,15,29,31,33,34,39,45,47,90,91 25.00 C17-19,49-53,56,59,61,67-71,74-76,78,80,81,94,202 3.00 C10,38,41 2.00 C13,66 1.00 C73 1.00 C44 2.00 C85,86 1.00 T1 1.00 C3 1.00 C4 1.00 C37 1.00 C5 1.00 C6 1.00 C7 1.00 C36 1.00 C55 10.00 C1,12,14,22,23,25,28,30,32,35 6.00 C27,40,42,43,46,48 2.00 C77,79 2.00 C21,24 1.00 C20 1.00 C58 3.00 C60,200,201 13.00 D3-11,14,15,16,17 1.00 D1-1

19

Part Name C/F. RESISTOR.SMD C/F. RESISTOR.SMD C/F. RESISTOR.SMD C/F. RESISTOR.SMD C/F. RESISTOR.SMD C/F. RESISTOR.SMD C/F. RESISTOR.SMD C/F. RESISTOR.SMD C/F. RESISTOR.SMD C/F. RESISTOR.SMD C/F. RESISTOR.SMD C/F. RESISTOR.SMD C/F. RESISTOR.SMD C/F. RESISTOR.SMD C/F. RESISTOR.SMD C/F. RESISTOR.SMD C/F. RESISTOR.SMD C/F. RESISTOR.SMD C/F. RESISTOR.SMD C/F. RESISTOR.SMD

Specification 22J, 1/8W 220J, 1/8W 2.2KJ, 1/8W 22KJ, 1/8W 240J, 1/8W 270J, 1/8W 2.7KJ, 1/8W 300J, 1/8W 33J, 1/8W 330J, 1/8W 33KJ, 1/8W 39KJ, 1/8W 470J, 1/8W 4.7KJ, 1/8W 51J, 1/8W 510J, 1/8W 5.1KJ, 1/8W 62J, 1/8W 7.5KJ, 1/8W 8.2KJ, 1/8W

q"ty 3.00 28,47,102 3.00 4,29,118 4.00 9,10,90,91 1.00 89 1.00 147 1.00 41 1.00 11 1.00 39 3.00 27,72,170 4.00 34,95,98,99 1.00 40 1.00 71

Referance.

7.00 93,94,96,97,100,101,108 1.00 30 1.00 114 4.00 86,87,R01,R02 3.00 74,75,76 2.00 146,148 2.00 7,73 1.00 104 1.00 SFR11 2.00 SFR10,13 8.00 SFR1,2,3,4,5,6,7,16 2.00 SFR12,15 1.00 SFR8 4.00 21,35,37,38 1.00 117 2.00 23,25 1.00 136 2.00 12,16 (1.2K,F) 2.00 R13,17 1.00 133 2.00 137,139 (22,F) 1.00 135 1.00 R115 (243,F)

SEMI-FIXED RESISTOR VZ067TH1, 100B SEMI-FIXED RESISTOR VZ067TH1, 1KB SEMI-FIXED RESISTOR VZ067TH1, 10KB SEMI-FIXED RESISTOR VZ067TH1, 100KB SEMI-FIXED RESISTOR VZ067TH1, 2KB M/F. RESISTOR.SMD M/F. RESISTOR.SMD M/F. RESISTOR.SMD M/F. RESISTOR.SMD M/F. RESISTOR.SMD M/F. RESISTOR.SMD M/F. RESISTOR.SMD M/F. RESISTOR.SMD M/F. RESISTOR,SMD M/F. RESISTOR.SMD 1KF, 1/8W 100KF, 1/8W 11KF, 1/8W 120F, 1/8W 1.21KF, 1/8W 121KF,1/8W 1.5KF, 1/8W 21.5F, 1/8W 2.2KF, 1/8W 249F, 1/8W

20

Part Name M/F. RESISTOR.SMD M/F. RESISTOR.SMD M/F. RESISTOR.SMD M/F. RESISTOR.SMD M/F. RESISTOR.SMD M/F. RESISTOR.SMD M/F. RESISTOR.SMD M/F. RESISTOR.SMD M/F. RESISTOR

Specification 24.9KF, 1/8W 3.32KF, 1/8W 42.2F, 1/8W 430F, 1/8W 4.99KF, 1/8W 56.2F, 1/8W 576F, 1/8W 825 1/8W F

q"ty 1.00 129 (24.3K,F) 1.00 119 (3.4K,F) 1.00 120 2.00 22,24 1.00 132 1.00 138 (56,F) 1.00 121 2.00 127,130 1.00 32 1.00 66 1.00 1.00 1.00 P-S/W1 1.00 U3 2.00 U1,2 Rohm 1.00 U20 1.00 U5 1.00 U7 1.00 U8 1.00 U17 1.00 U4 1.00 U18 2.00 U10,11 1.00 U14 1.00 U13 1.00 U9 1.00 1.00 10M 20PPM . 1.00 1.00 1.00 U15 Ass'y 1.00 U15 Ass'y 3.00 U37,15,20 0.00 MAIN PCB GND 2.00 Q16,29 Ass'y 2.00 U7,15 Assy' 1.00 U20 Ass'y

Referance.

900F, 1/4W

OXIDE FILM RESISTOR 560J, 1W KEY SWITCH KEY SWITCH POWER SWITCH I.C.(TI) I.C.SMD I.C.(SAM.MOTO.NS.) I.C.(SAM.MOTO) I.C.(SAM.MOTO) I.C.(MOTO.) I.C.(HAR.RCA) I.C.SMD(SIG) I.C(NS) I.C.SMD(NS.HIT.PHI.) I.C.SMD(NS.HIT.SGS.) I.C.(TOSHIBA) I.C.(AMD) WIRE ASS'Y(1365#30) CRYSTAL MAIN PCB SHIELD CASE NUT SCREW, MACHINE SCREW, TAPPING SPRING, COIL HEAT SINK HEAT SINK HEAT SINK SPUN90X1CO21 SPUN40X1C041 JPP2295MPACS72 SN75107AN BA10324AF MC7805 MC7815 MC7915 MC10116 CA3096AE SN7400/SN74S00 74F191N SN74HC393 SN74HC138 TD62783AP GAL16V8 IN PUT CABLE,250mm 10.0000MHz(HC-49/U) 8210-M12 Zn-pl 0.3t 104x40x18 M3, NI-PL M3x8BH, NI-PL T3x6BH,ZN-PL 6x2x7(SHIELD ) TR , 8.3, 16 78SERIES () 8210 17x9x19

21

4-2.. Display

PCB Parts List

Specification 8pin,YW02508, HDSP-H513#001 HDSP-K513#001 BL-R2130A-T(5x5X10) 8210-DIS-01 Q'ty 2.00 CN12,13 1.00 FND(SINGLE ) 3.00 FND1,2,3 5.00 LED 1-5 1.00 Referance

Part Name WAFER FND(hp) FND(hp) LED DISPLAY PCB(80SER.)

4-3.. VR PCB Parts List

Part Name WAFER WAFER VARIABLE RESISTOR VARIABLE RESISTOR VARIABLE RESISTOR VARIABLE RESISTOR VARIABLE RESISTOR VR PCB(80SER.) Specification 3pin,YW02503, 4pin,YW02504, V16L4(7x5)S15KCB10K V16L4(7x5)S15KCB5K V16L4(7x5)S15KCB50K V16L4N15KCB10K V16L4N15KCB500 8210-VR-02 Q'ty Referance

5.00 CN8(WIDTH),CN9(RATE),CN2(FREQ),CN5(AMP),CN6(OFFSET) 1.00 CN3(SYM) 1.00 VR5(WIDTH), 1.00 VR4(OFFSET) 1.00 VR2(SYM) 2.00 VR6(RATE),VR1(FREQ), 1.00 VR3(AMP) 1.00

4-4. Front Panel Assembly Parts.

Part Name BNC CONNECTOR WIRE ASS'Y( WIRE ASS'Y( BRACKET, VR PCB BRACKET, BNC FRONT PANEL, ABS KNOB, VR, ABS PLATE, FRONT, PC ACRYLE FILTER NUT(VR) NUT(BNC,F) NUT SCREW, MACHINE SCREW, TAPPING WASHER, PLAIN WASHER,PLAIN(VR) WASHER,LATCH(BNC) WASHER,PLAIN(BNC S.) DISPLAY PCB ASS'Y VR PCB ASS'Y M3, NI-PL M3x4BH,NI-PL T3x8BH, ZN-PL :3,:12/NI-PL 7.2x12x0.2t/NI-PL 9.5x13x0.5t/NI-PL 10x13x0.3t/NI-PL FG-8210/DAGA FG-8210/DAGA ) ) Specification BNC-RB-4CUTTING 2pin 150mm 2pin 220mm BN-LGP,160x25x30 BN(80SER.)-AG/FG BN(80SER-)-12965 Pi10x13mm,DARK-GRAY 8210DAG 8210-DAG Q'ty Referance

4.00 OUTPUT,TTL SYNC, VCF, EXT COUNTER IN 1.00 VCF 2.00 TTL.OUTPUT 1.00 1.00 1.00 6.00 1.00 1.00 6.00 VR 4.00 BNC BRACKET 2.00 BNC BRACKET 2.00 BNC BRACKET 5.00 VR PCB 2.00 EXT COUNT IN BNC 6.00 VR 4.00 BNC 4.00 BNC 1.00 1.00

22

4-5. Rear Panel Assembly Parts.

Part Name FUSE(UL,VDE) FUSE HOLDER EMI GASKET MOTOR FAN GND CONNECTOR AC INLET(SAM IL) POWER TRANS I.C.(SAM.MOTO.NS.) HEAT TUBE HEAT TUBE WIRE ASS'Y(1015#22) WIRE ASS'Y(1015#22) WIRE ASS'Y(1015#22) BRACKET, TRANS REAR PANEL PRESS NUT(GND TERMINAL) NUT SCREW, MACHINE SCREW,MACHINE SCREW, MACHINE WASHER, PLAIN WASHER, SPRING WASHER, LATCH POWER

Specification 50F,250V200mA(20mm) R3-11,BN 71TS-FK10-R10-170-00 DC5V,0.5W (40x40)

Q'ty 1.00 FUSE HOLDER IN

Referance

1.00 REAR PANEL ASS'Y 1.00 REAR PANEL ASS'Y 1.00 REAR PANEL ASS'Y 1.00 REAR PANEL ASS'Y

NFU-101,NOISE FILTER FG-8210,8220 MC7805 Pi5 x 15 mm Pi 12 x 60 mm GND WIRE,180mm,LUG DIW,120mm,BLACK 3pin 2Wire ,220mm

1.00 REAR PANEL ASS'Y 1.00 REAR PANEL ASS'Y 2.00 REAR PANEL ASS'Y (U5,U15) 3.00 AC INLET,FUSE HOLDER 1.00 FUSE HOLDER 3.00 REAR PANEL ASS'Y 1.00 AC IN-FUSE 1.00

BN-DAG, 27x10.5,2T BN-DAG,FG-8210 INCH M3, NI-PL M3x10BH, M3x16BH M3x8BH-W, NI-PL :3,:10/NI-PL :3,:5, ZN-PL 4x6.5x0.3t

2.00 TRANS 1.00 2.00 GND CONNECTOR 8.00 TRANS,REGULATOR, FAN 2.00 NOISE FILTER (AC INLET) 2.00 FAN 2.00 TRANS 4.00 TRANS,AC INLET 2.00 TRANS 1.00 GND CONNECTOR

23

4-6. Others.

Part Name I.C.(ATMEL) CABLE TIE WIRE ASS'Y(#24) WIRE ASS'Y(#24) WIRE ASS'Y( WIRE ASS'Y( ) )

Specification AT89C52 100mm, WHITE 3-3pin 150mm 4-4pin 150mm 8-8pin 220mm 3-3pin 150mm 0.6t 210x202(156)x35 Znpl 0.6t 210x202x35 BN(80SER,)-12965 BN(80SER.)-12965 BN(80SER.)-12965 BN-DAG,37x8.5, BN-DAG,32x8.5, 71TS-FK10-R10-170-00 BN-DAG, 248X163 20x40,5T, BN-DAG(80SER.) BN(80SER.)-12965 M3x6BH,H5, NI-PL M4x45BH, ZN-PL T3x8BH, H6, NI-PL Pi3x50, 8210MAIN :3,:5, ZN-PL SUI40-24-125-45-13 FG-8210/DAGA FG-8210/DAGA FG-8210/DAGA

Q'ty 1.00 U12 10.00 6.00 1.00 2.00 1.00 1.00 MOUNT POLE- TOP 1.00 MONUT POLE-BOTTOM 1.00 1.00 1.00 2.00 BOTTOM CASE 2.00 TOP CASE

Referance

SHIELD CASE 8210 TOP SHIELD CASE 8K-BOT BOTTOM CASE, ABS TOP CASE, ABS HANDLE, ABS RUBBER FOOT RUBBER FOOT EMI GASKET SHIELD PLATE SPONGE PAD KNOB, POWER, ABS KNOB, PUSH S/W, ABS SCREW, MACHINE SCREW, MACHINE SCREW, TAPPING MOUNTING POLE WASHER, SPRING EMI AIR VENT FILTER FRONT PANEL ASS'Y REAR PANEL ASS'Y MAIN PCB ASS'Y

1.00 BOTTOM SHIELD CASE ASS'Y 0.00 SHIELD CASE BOTTOM 6.00 MAIN PCB AC LINE PART

1.00 POWER STICK 13.00 KEY S/W 0.00 SHIELD TOP + MOUNT POLE 4.00 TOP+BOTTOM CASE 3.00 PCB -BOTTOM CASE 1.00 MAIN PCB-SHIELD CASE 1.00 SHIELD TOP + MOUNT POLE 2.00 TOP,BOTTOM SHIELD 1.00 1.00 1.00

24

4-7. Packing

Part Name FUSE(UL,VDE) POWER CORD(230V) CABLE ASS'Y( STYROFOAM BOX SILICA GEL STICKER, S/N, 230V MANUAL(8210) INNER BOX (8000SER.) CARTON BOX() VINYLE BAG VINYLE BAG )

Specification 50F,250V200mA(20mm) KKP-30,SVT3/18A"VDE" BNC TO CLIP( BENCH, 300x150x65mm 3g BN(80SER.),15W200mA FG8210, DAG DAG-BN,340x310x165 BN,645x355x365 70x100mm,Zipper Type 265x400mm )

Q'ty 1.00 SPARE FUSE. 1.00 "VDE" 1.00 2.00 1.00

Referance

1.00 15w ,230V/200mA F 1.00 1.00 0.25 4CTN.(IN BOX -340x310x165) 1.00 SPARE FUSE. 1.00 PRODUCT.

5. CIRCUIT DIAGRAM - Refer to Attached File.

25

R83 10K

COUNTER 06-R150#1 + C40 47/16V +5VD C39 103 R87 510 C44 470P(C/C) BNC4 EXT COUNT IN 1 C37 474/250V SW5 EXT/INT SW C38 130P 2 R85 100K Q18 2N5486 3 1 R88 150 C9 47/16V + R95 330 U8A MC10116 2 4 13 5 9 C41 130P D11 1N4148 R86 510 SFR16 10K 2 + C43 47/16V + C46 47/16 C45 103 15 1 10 9 +5VD C90 103 SW6 L.P.F C12 103 D17 1N4148 14 4 5 11 A B C D QA QB QC QD RCO 3 2 6 7 13 1 R90 2.2K R91 2.2K Q19 2N3906 8 6 11 3 12 14 R99 330 C48 47/16V + C47 103

+5V(A)

U8B MC10116 10

1/16

Q20 2N3906 U8C MC10116 15

R92 150 7

R102 22

Q21 2N3906

D10 1N4148

R93 470 R89 22K

R94 470

R96 470

R97 470

R98 330 R100 470 R101 470

R103 120

R108 470

D16 1N4148

C91 103

CLK G D/U LOAD MX/MN U18 74LS191

12

06-U9#3 06-U9#5 06-U9#4

R01 510

C01 50P

R02 510

C02 50P

Title Model Size Sheet

8210 - 05
COUNTER PREAMP CIRCUIT

Drawing

Design

Checked

Approved

A3

Rev Scale

02
2:1

5 of 6
2002/04/13

Date

DAGATRON

/Sa /Sb /Sf /Sg /Sa /Sb /F3 /F4 /Sf /Sa /Sb /Sf /Sg /Sa /Sb /F5 /F6 /Sf /Sa /Sb /Sf /Sg /Sa /Sb /F7 /F8 /Sf /Sa /Sb /Sf /Sg /Sa /Sb /F9

mHZ HZ KHZ MHZ G.T

D1 D2 D3 D4 D5

/Sc /Sd /Se

1 2 3 4 5 6 7 8 9

1 2 3 4 5 6 7 8 9

1 2 3 4 5 6 7 8 9 FND3 SEGMENT

+5V(D)

8.8. 8.8. 8.8. 8.

18 17 16 15 14 13 12 11 10 18 17 16 15 14 13 12 11 10 18 17 16 15 14 13 12 11 10 C52 104 C56 104 C53 104 /Se /Sd /Sc /Sh /Se /Sd /Sg /Sc /Sh /Se /Sd /Sc /Sh /Se /Sd /Sg /Sc /Sh /Se /Sd /Sc /Sh /Se /Sd /Sg /Sc /Sh /F3 /F4 /F5 /F6 /F7 /F8 /F9

FND1 SEGMENT

FND2 SEGMENT

C49 104

C50 104

C51 104

8 7 6 5 4 3 2 1

U9 PAL16R4 12 13 14 15 16 17 18 19 F0 F1 F2 F3 F4 F5 F6 F7 I0 I1 I2 I3 I4 I5 I6 I7 I8 I9 1 2 3 4 5 6 7 8 9 11

J13 CN13 05-U18#14 05-U18#7 05-U18#6 1 2 3 4 5 6 7 8 J13' CN13' U13 TB62783 I0 I1 I2 I3 I4 I5 I6 I7 O1 O2 O3 O4 O5 O6 O7 O8 18 17 16 15 14 13 12 11 1 2 3 4 5 6 7 8 J3 CN3 1 2 3 4 5 6 7 8 J3' CN3' 1 2 3 4 5 6 7 8 /Sa /Sb /Sc /Sd /Se /Sf /Sg /Sh

/Se /Sd /Sc /Sh /Se

10 9 8 7 6

1 2 3 4 5 FND4 SEGMENT

/CO0

/CO1

/CO2

/CO3

/CO0 /CO1 /CO2 /CO3 /CO4 /CO5 /CO6 /CO7 /CO4

1 2 3 4 5 6 7 8

1 2 3 4 5 6 7 8

/CO5

/CO6

U12 89C52 U10A 74LS393 1 2 A CLR QA QB QC QD 3 4 5 6 16 17 13 21 22 23 24 25 26 27 15 28 14 3 4 5 6 39 38 37 36 35 34 33 32 WR RD INT1 P2.0 P2.1 P2.2 P2.3 P2.4 P2.5 P2.6 T1 P2.7 T0 P0.0 P0.1 P0.2 P0.3 P0.4 P0.5 P0.6 P0.7 EA/VP RESET X1 31 9 19 /a /b /c /d /e /f /g /h

Q22 A1015

Q23 A1015

Q24 A1015

Q25 A1015

Q26 A1015

Q27 A1015

Q28 A1015

Q32 A1015

U10B 74LS393 13 12 A CLR QA QB QC QD 11 10 9 8

P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 RXD TXD INT0

1 2 3 4 5 6 7 8 10 11 12

R105 10 /CM0 /CM1

R106 10 /CM2

R107 10 /CM3

R108 10 /CM4

R109 10 /CM5

R110 10 /CM6

R111 10 /CM7

R112 10

/CO7

U14 74LS138 1 2 3 +5V(D) +5V(D) 6 4 5 A B C G1 G2A G2B Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 15 14 13 12 11 10 9 7 /CM0 /CM1 /CM2 /CM3 /CM4 /CM5 /CM6 /CM7 05-SW5#5 R150 1K R104 8.2K

+5V(D)

U11A 74LS393 1 2 A CLR QA QB QC QD

R149 10

+ Y1 10MHZ

C55 10/16V

Q30 C1815

13 12

A CLR

29 30

QA QB QC QD

11 10 9 8

PSEN ALE/P

U11B 74LS393

X2

18 T1 20P

C64 30P

C57 56P

Title Model

8210 - 06
CPU CONTROL CIRCLE A3
Rev Scale

Drawing

Design

Checked

Approved

Size Sheet Date

02
2:1

6 of 6
2002/04/13

DAGATRON

4
D8 1N4148 J8 CN8 1 2 3

Sweep Width

VR5 10KB

SW1 SWEEP WIDTH 3 2 1 8

R70 1K

+15V

+15V

D
1 -15V +15V R73 7.5K J9 CN9 2 1 2 3 R71 39K 9 10 R72 33 8 + U2C GL324 C36 0.22uF(MYLER) R75 5.1K R74 5.1K 13 12 14 + U2D GL324 R76 5.1K Q17 2N3906 5 6 C31 0.01(C/C) +

D
SFR8 2.2KB

C30 22/16V

3 R11 2.7K 02-U30A#12 7 U2B GL324 Q2 2N3904 + 11 D9 1N4148 R77 10K C33 0.01(C/C) -15V + C32 22/16V 4

Sweep Rate

VR6 10KB

C
BNC1 VCF IN 1 2 J1 CN1 1 2 C304 104 R1 10K R3 1K U1B GL324 7 2 3 1 + U1A GL324 R8 1K Q1 2N3906 R300 470 R2 1K R4 220

R9 2.2K

SFR6 10KB

3 2 5 + 6 R10 2.2K 1

J2 CN2 2 1 2 3 R114 51

Frequency

VR1 10KB

SFR1 10KB 3 SFR2 10KB 3 SFR3 10KB 3 +15V SFR4 10KB 3 R6 1K SFR5 10KB 3

+21V 1 C29 0.01(C/C) 1 4 10 1 9 3 + C28 22/25V -15V J3 CN3 4 3 2 1 VR2 50KB SFR7 10KB 2 3

+ 11 U1C GL324

8 2

02-U30B#3

3 1 R7 7.5K C2 0.22uF -5V + 1 8 22/16 C37 SW2 Symm Title Model Size Sheet Date

8210 - 01
FREQ/VCF IN CIRCUIT A3
Rev Scale

Drawing

Design

Checked

Approved

02
2:1

1 of 6
2002/3/30

DAGATRON
1

4
02-R19#1 02-U4A#1 02-R32#1

2
+15V

+5V

R46 2K

C19 0.1(MON) R117 100KF 2 SFR15 100K R118 220 1 2 3 4 5 6 R119 3.32KF R120 R121 42.2F 576 7 8 U17 CA3096 Q1B Q1E Q1C Q2E Q2B Q2C Q3E Q3B SUB Q5C Q5B Q5E Q4C Q4B Q4E Q3C 16 15 14 13 12 11 10 9

R126 100 R124 1K R125 1K C67 0.1(MON)

C76 0.1(MON) R138 56.2F R140 10(1/2W) C78 0.1(MON) D5 1N4148

R69 10

R127 825F

C75 0.1(MON) R139 21.5F

+ C77 100/25V

C35 22/16V +

C34 0.01

SW1 SINE

SW2 TRIANGLE

SW3 SQUARE

R128 150

Q14 2N3563 Q15 2N3906 Q16 2N2219 R147 240

3 SFR10 1KB

C17 0.1(MON) R37 1KF

C66 150P

C
R33 2K C87 22P

R132 4.99KF C68 0.1(MON)

C71 0.1(MON)

D6 1N4148 R146 62 R148 62

Q10 C3198

R135 10(1/2W) R129 24.9KF R115 249 R134 1.5KF R136 2.2KF

R141 10(1/2W) R144 100(1/2W) BNC3 6 5 1 2 2 1 3 SW3 ATT C82 100P RG58

R41 270 R40 33K Q8 Q9 C1815 C3198 2 SFR12 100KB 3 2 R43 1K 1 R42 220 Q11 C3198 3 J5 CN5 2 3 2 1 R116 R47 10K 22 1

OUTPUT
1 2

R122 1.1K +15V R123 1.21K C72 1.5pF C69 0.1(MON) C18 0.1(MON) R160 1K Q12 2N5771 J6 CN6 SW4 DC OFFSET 1 2 3 2 1 R161 1K R131 100 C70 0.1(MON) R130 825F C74 0.1(MON) C80 0.1(MON) + C73 1.5pF D7 1N4148 Q29 2N2905 Q13 2N3904 D14 1N4148 100/25V C79 R142 10(1/2W) R145 100(1/2W)

R34 330

3 SFR11 100B R35 1KF

R42 1K R38 1KF

VR3 AMP 500B

SFR13 1KB R36 1K 1 2

R137 21.5F

R136 144F

R74 10(1/2W) C81 0.1(MON)

VR4 5K

C14 22/10V

R44 10

-15V C15 0.01uF(CER) Title Model

A
-5V

8210 - 03
AMPLFIER CIRCUIT A3
Rev Scale

Drawing

Design

Checked

Approved

Size Sheet Date

02
2:1

3 of 6
2002/04/13

DAGATRON
1

+21V +21V

R68 10/0.5W

C20 2200/35V +15V

J14' CN14' 1 2 3

J14 CN14 1 2 3 2 -

DB1 DB06M U5 7815 + 4 1 + C21 1000/35V GND VIN VOUT 3 + C22 22/16V 1 VIN U6 7805 GND VOUT 3 + C23 22/16V +5V

+15V

+5V

U7 7915 2 VIN GND VOUT 3 C25 22/16V -15V 1 -15V

C
R66 560/1W

C24 1000/35V

2 + U15 7805 GND VOUT 3 + C60 470/16V C61 104 2 U20 7805 1 GND VIN VOUT 3 C201 470/16V + C203 104 2 Title Model Size Sheet Date

T2 TRANSFORMER POWER 11 F1 NOISE FILTER 1 3 2 F2 FUSE J15' CN15' 1 2 3 J15 CN15 1 2 3 SW8 POWER S/W 1 2 3 4 ST1 SELECT J16' CN16' 1 2 3 J16 CN16 1 2 3 1 2 3 4 5 6 7 8 9 J5' CN5' 1 2 3 J5 CN5 1 2 3 D22 1N4003 C202 104 J4' CN4' 1 2 3 J4 CN4 1 2 3 D13 1N4003 FAN DC FAN 1 2 D12 1N4003 1 C59 104 + C58 2200/16V VIN

10 C306 104/1KV C307 104/1KV

D20 1N4003

+ C200 470/16V

8210 - 04
POWER SUPPLY CIRCUIT A3
Rev Scale

4 of 6
2002/04/13

ZD1 5.1V

-5V

C27 47/35V

-5V +5V(D)

+5V(D)

J17 CN17 1 2

Drawing

Design

Checked

Approved

02
2:1

DAGATRON

+15V

D
R12 1.2KF R13 120KF +5V L2 INDUCTOR AUDIO C100 10n +5V L1 INDUCTOR AUDIO Q5 2N5486 C101 10n(C/C) 14 2 C305 10n C12 100/10V

R26 1K D1-2 HSMS2825

01-R11#1

14 6 8

VCC+ S 2G

Q7 2N3563 C86 472 Q4 3563 1 U30A 072 R15 10K 3 2 R001 ??? C7 0.68n(BOX) 1 Q6 2N5486 C84 30P(C/C)

C10 130P

11 12 2 1

2B 2A 1B 1A

2Y

VCC-

1Y 1G

4 U4 SN75107

R30 4.7K

R29 4.7K

01-CN3#1

3 2

+ -

R20 1K

R21 1KF

13

1 5 3 2 L3 INDUCTOR AUDIO U4A 74LS00 R31 240

B
R18 10 R16 1.2KF R17 120KF R19 1.5K C9 15P(C/C)

12

14 U30D 072

13

R14 10K

Q3 5771 C3 33P C4 680P(BOX)

R23 11KF D3 1N4148 R24 430F 4

C85 472 D1-1 HSMS2825

BNC2 6 R27 33 R28 22 C13 150P J10 CN10 1 2 TTL SYNC OUT R170 33

C5 6.8n(BOX) C6 68n(BOX) D4 1N4148 C8 0.01(C/C)

5 U4B 74LS00

OUTPUT
1

R24 430

R25 11KF -5V

R32 2.2K

03-SW3#6 03-SW3#2 03-R46#1

Shield Box

Title Model Size Sheet Date

8210 - 02
OSCILLATOR/TTL CIRCUIT A3
Rev Scale

Drawing

Design

Checked

Approved

02
2:1

2 of 6
2002/3/30

DAGATRON
1