Control Valve HP

Download as pdf or txt
Download as pdf or txt
You are on page 1of 48
At a glance
Powered by AI
The document provides installation, maintenance and parts information for Fisher Design HP and HPA control valves.

The document discusses specifications, installation, maintenance, trim removal and replacement, valve plug maintenance, lapping seats, parts ordering and a parts list for Fisher Design HP and HPA control valves.

The document describes maintenance tasks such as packing lubrication and maintenance, adding packing rings, replacing packing, trim removal, valve plug maintenance, and lapping seats.

Instruction Manual

Form 5299 April 2004

HP and HPA Valves

Design HP and HPA Control Valves


Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Scope of Manual . . . . . . . . . . . . . . . . . . . . . . . . . 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Packing Lubrication . . . . . . . . . . . . . . . . . . . . . . . 6 Packing Maintenance . . . . . . . . . . . . . . . . . . . . . 6 Adding Packing Rings . . . . . . . . . . . . . . . . . . . . 7 Replacing Packing . . . . . . . . . . . . . . . . . . . . . . . 7 Trim Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Valve Plug Maintenance . . . . . . . . . . . . . . . . . . 12 Lapping Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Trim Replacement . . . . . . . . . . . . . . . . . . . . . . . 16 Retrofit: Installing C-seal Trim . . . . . . . . . . . . . 18 Replacement of Installed C-seal Trim . . . . . . 20 Trim Removal (C-seal Constructions) . . . . . . . . . . . . . . . . 20 Lapping Metal Seats (C-seal Constructions) . . . . . . . . . . . . . . . . 21 Remachining Metal Seats (C-seal Constructions) . . . . . . . . . . . . . . . . 21 Trim Replacement (C-seal Constructions) . . . . . . . . . . . . . . . . 22 Parts Ordering . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Parts Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

W5785A-1

Figure 1. Design HP Valve with Type 657 Actuator

Introduction
Scope of Manual
This instruction manual includes installation, maintenance, and parts information for 1- through 6-inch Design HP valves with Class 900 and 1500 ratings; and 1- through 2-inch Design HP and HPA valves with Class 900, 1500, and 2500 ratings. Refer to separate manuals for instructions covering the actuator, positioner, and accessories. No person may install, operate, or maintain HP Series valves without first D being fully trained and qualified in valve, actuator, and accessory installation, operation, and maintenance, and D

carefully reading and understanding the contents of this manual. If you have any questions about these instructions, contact your Fisher sales office before proceeding. Note Fisher does not assume responsibility for the selection, use, or maintenance of any product. Responsibility for proper selection, use, and maintenance of any Fisher product remains solely with the purchaser and end-user.

www.Fisher.com

D101634X012

Instruction Manual

HP and HPA Valves


Table 1. Specifications

Form 5299 April 2004

End Connection Styles and Ratings(1,2,3,4) Flanged: Consistent with Class 900, 1500, and 2500 per ASME B16.34 Socket Welding: Consistent with Class 900, 1500, and 2500 per ASME B16.34 Buttwelding: Consistent with Class 900, 1500, and 2500 per ASME B16.34 Also see table 2 Shutoff Classifications See table 3 C-seal trim: High-temperature, Class V. See table 4 TSO (Tight Shutoff) trim: See tables 5 and 6 Flow Characteristic Standard Cage: J Equal percentage, J Modified equal percentage or, J Linear Standard Cage with Micro-Formt Valve Plug: (Design HPS and HPAS only): J Equal percentage or J Modified equal percentage Standard Cage with Micro-Flutet Valve Plug: (Design HPS and HPAS only): J Equal percentage or J Modified equal percentage
1. 2. 3. 4. 5.

Standard Cage with Micro-Flatt Valve Plug: (Design HPAS only): J Linear Cavitrolr III or Whisper Trimr III Cage: J Linear Special cages: Special characterized flow cages are available. Consult your local Fisher sales office. Flow Direction Standard Cage J Design HPD and HPAD: Normally flow down J Design HPS and HPAS: Normally flow up(5) J Design HPAS Micro-Flat: Flow down J Design HPT and HPAT: Normally flow down J Design HPS and HPAS Micro-Form: Flow up only Cavitrol III Cage: Flow down Whisper Trim III Cage: Flow up Approximate Weights (valve body and bonnet assemblies) See table 2 Additional Specifications For specifications such as materials, valve plug travels, and port, yoke boss, and stem diameters, see the Parts List section

DIN (or other) ratings and end connections can usually be supplied; consult your Fisher sales office. Class 900 and 1500 globe valves are identical for size 1- and 2-inch valves. Class 900 and 1500 globe valves for size 3-, 4-, and 6-inch valves, however, are not identical. The centerline-to-face dimension for Class 2500 1- and 2-inch Design HPA valves does not conform to ANSI/ISA S75.12. The pressure or temperature limits in this manual and any applicable standard limitations should not be exceeded. Design HPS and HPAS valves may be used flow down for on-off service only or where further limited by trim design. Design HPAS valves may be used flow down for erosive service.

Description
The HP Series high-pressure globe and angle valves (figure 1) have metal seats, cage guiding, quick change trim, and push-down-to-close valve plug action. The Design HPD, HPAD, HPT, and HPAT valves use balanced valve plugs. The Design HPS and HPAS valves use an unbalanced valve plug. To provide a seal between the cage and a balanced valve plug, the Design HPD and HPAD valve plugs use piston rings; the Design HPT and HPAT valve plugs use a pressure-assisted seal ring. A Whisper Trim cage can be used with a Design HPD, HPAD, HPS, HPAS, HPT, or HPAT valve plug. A Cavitrol III cage can be used with a Design HPS, HPAS, HPT, or HPAT valve plug.

C-seal trim is available for Design HPD valves, class 900 and 1500, in sizes 3, 4, and 6. With C-seal trim, a balanced valve can achieve high-temperature, Class V shutoff. Because the C-seal plug seal is formed from metal (N07718 nickel alloy, Inconel 718) rather than an elastomer, a valve equipped with the C-seal trim can be applied in processes with a fluid temperature of up to 593_C (1100_F), provided other material limits are not exceeded.

Specifications
Specifications for the HP Series valves are shown in table 1.

Instruction Manual
Form 5299 April 2004

HP and HPA Valves


at the beginning of the Maintenance section in this instruction manual.

Table 2. Approximate Weights (Valve and Bonnet Assemblies)


VALVE SIZE, INCHES KILOGRAMS CLASS Flg SWE & BWE 38 34 34 52 74 --97 --201 --455 36 72(1) 50 109(1) Flg POUNDS SWE & BWE

Globe Valves 1 1.5 x 1 2 3 4 6 900 & 1500 2500 2500 900 & 1500 2500 900 1500 900 1500 900 1500 900 & 1500 2500 900 & 1500 2500 42 45 --72 104 125 129 230 249 511 557 40 --69 --93 100 --158 229 276 284 507 548 1127 1228 88 --153 --85 76 76 115 164 --213 --444 --1003 80 160(1) 110 240(1)

WARNING
Some bonnet flanges have a tapped hole that was used to handle the bonnet during manufacture. Do not use this tapped hole to lift the valve assembly or personal injury may result.

CAUTION
When ordered, the valve configuration and construction materials were selected to meet particular pressure, temperature, pressure drop, and controlled fluid conditions indicated when the valve was ordered. Since some body/trim material combinations are limited in their pressure drop and temperature ranges, do not apply any other conditions to the valve without first contacting your Fisher sales office. 1. Before installing the valve, inspect it to ensure that the valve body cavity is free of foreign material.

Angle Valves 1 2

1. Only SWE is available for Class 2500.

Installation
WARNING
Always wear protective gloves, clothing, and eyewear when performing any installation operations to avoid personal injury. Personal injury or equipment damage caused by sudden release of pressure may result if the valve assembly is installed where service conditions could exceed the limits given in table 1 or on the appropriate nameplates. To avoid such injury or damage, provide a relief valve for over-pressure protection as required by government or accepted industry codes and good engineering practices. Check with your process or safety engineer for any additional measures that must be taken to protect against process media. If installing into an existing application, also refer to the WARNING

2. Clean out all pipelines to remove scale, welding slag, and other foreign materials before installing the valve. Note If the valve body being installed has small internal flow passages, such as with Whisper Trim III or Cavitrol III cages, consideration should be given to installing an upstream strainer to prevent the lodging of particles in these passages. This is especially important if the pipeline cannot be thoroughly cleaned or if the flowing medium is not clean. 3. Flow through the valve must be in the direction indicated by the flow arrow, which is stamped on or attached to the valve body. 4. Use accepted piping practices when installing the valve in the pipeline. For flanged valve bodies, use a suitable gasket between the body and pipeline flanges.

Instruction Manual

HP and HPA Valves


Table 3. Shutoff Classifications per ANSI/FCI 70-2 and IEC 60534-4
VALVE DESIGN PORT DIAMETER, mm (INCHES) 47.6 (1.875) and smaller HPD, HPAD 58.7 (2.3125) to 92.1 (3.625) 111.1 (4.375) and larger HPS, HPAS w/ Cavitrol III, or HPT, HPAT w/ Cavitrol III, or HPAS w/Micro-Flat HPS, HPAS, HPT, HPAT, HPS, HPAS w/ Micro-Form, or HPS, HPAS w/ Micro-Flute HPT w/ PEEK anti-extrusion rings All All 47.6 (1.875) to 136.5 (5.375)

Form 5299 April 2004

LEAKAGE CLASS II II - Standard III - Optional III - Standard IV - Optional V IV-Standard V-Optional V to 316_C (600_F)

Table 4. Additional Shutoff Classification per ANSI/FCI 70-2 and IEC 60534-4
VALVE DESIGN (CLASS) VALVE SIZE, INCHES 3 4 4 Design HPD with optional C-seal trim 4 PORT DIAMETER, mm (INCHES) 73.0 (2.875) 73.0 (2.875) 87.3 (3.4375) 92.1 (3.625) 111.1 (4.375) 115.8 (4.5625) 136.5 (5.375) 133.4 (5.25) CAGE STYLE Equal Percentage, Modified Equal Percentage, Linear (std. cage), Linear (Whisper III, A1, B1) Linear (Whisper III, D3), Linear (Cavitrol III, 3-stage) Linear (Cavitrol III, 2-stage) Equal Percentage, Modified Equal Percentage, Linear (std. cage), Linear (Whisper III, A1, B3, C3) Linear (Whisper III, D3) Linear (Cavitrol III, 3-stage) Equal Percentage, Modified Equal Percentage, Linear (std. cage), Linear (Whisper III, A1, B3, C3) Linear (Cavitrol III, 2-stage) LEAKAGE CLASS V V V V

Table 5. TSO (Tight Shutoff) Leakage Class per ANSI/FCI 70-2 and IEC 60534-4
Leakage Class TSO (Tight Shutoff) Maximum Leakage Valves with TSO trim are factory tested to a more stringent Fisher test requirement of no leakage at time of shipment. Test Medium Water Test Pressure Service P(1) Leakage Class V

1. Specify service P when ordering.

Table 6. TSO Shutoff Availability


TYPE HPS, HPT CONSTRUCTION Std or Cavitrol III trim. Replaceable, protected soft seat LEAK CLASS Standard TSO Optional ---

Instruction Manual
Form 5299 April 2004

HP and HPA Valves


Table 7. Recommended Torque for Packing Flange Nuts (non live-loaded)
STEM DIAMETER Inches 0.5 0.5 0.5 0.75 0.75 0.75 1 1 1 1.25 1.25 TORQUE VALVE BODY RATING Class 900 Class 1500 Class 2500 Class 900 Class 1500 Class 2500 Class 900 Class 1500 Class 2500 Class 900 Class 1500 NSm Min 12 15 18 27 34 41 42 52 61 56 68 Max 18 22 24 41 50 61 62 77 91 83 102 Min 9 11 13 20 25 30 31 38 45 41 50 lbfSft Max 13 16 18 30 37 45 46 57 67 61 75

STEM DIAMETER mm 12.7 12.7 12.7 19.1 19.1 19.1 25.4 25.4 25.4 31.8 31.8

5. Install a three-valve bypass around the valve if continuous operation is required during maintenance. 6. If the actuator and valve body are shipped separately, refer to the actuator mounting procedure in the appropriate actuator instruction manual. 7. If the valve body was shipped without packing installed in the packing box, install the packing before putting the valve body into service. Refer to instructions given in the Packing Maintenance procedure.

and maintenance frequency depends on the severity of service conditions. This section includes instructions for packing lubrication, packing maintenance, and trim maintenance. All maintenance operations may be performed with the valve in the line.

WARNING
Avoid personal injury or damage to property from sudden release of pressure or uncontrolled process fluid. Before starting disassembly: D Always wear protective gloves, clothing, and eyewear when performing any maintenance operations to avoid personal injury. D Disconnect any operating lines providing air pressure, electric power, or a control signal to the actuator. Be sure the actuator cannot suddenly open or close the valve. D Use bypass valves or completely shut off the process to isolate the valve from process pressure. Relieve process pressure on both sides of the valve. Drain the process media from both sides of the valve. D Vent the power actuator loading pressure and relieve any actuator spring precompression. D Use lock-out procedures to be sure that the above measures stay in effect while you work on the equipment.

WARNING
Personal injury could result from packing leakage. Valve packing was tightened before shipment; however, the packing might require some readjustment to meet specific service conditions. Valves with ENVIRO-SEALr live-loaded packing or HIGH-SEALt Heavy-Duty live-loaded packing will not require this initial re-adjustment. See the Fisher instruction manuals titled ENVIRO-SEAL Packing System for Sliding-Stem Valves or HIGH-SEAL Live-Loaded Packing System (as appropriate) for packing instructions. If you wish to convert your present packing arrangement to ENVIRO-SEAL packing, refer to the retrofit kits listed in the parts kit sub-section near the end of this manual.

Maintenance
Valve parts are subject to normal wear and must be inspected and replaced as necessary. Inspection

Instruction Manual

HP and HPA Valves


Table 8. Torque for Body-to-Bonnet Bolting Using Nickel Never-SeezR Lubricant
TORQUE VALVE RATING VALVE SIZE, INCHES 1 2 Class 900 & 1500 3 4 6 Class 2500 1 2 NSm B7, B16, BD and 660 Studs 260 390 730 970 1700 390 730 B8 and B8M Studs 150 240 530 730 1300 240 530 B7, B16, BD and 660 Studs 190 290 540 720 1250 290 540 lbfSft

Form 5299 April 2004

B8 and B8M Studs 110 180 390 540 950 180 390

D The valve packing box may contain process fluids that are pressurized, even when the valve has been removed from the pipeline. Process fluids may spray out under pressure when removing the packing hardware or packing rings, or when loosening the packing box pipe plug. D Check with your process or safety engineer for any additional measures that must be taken to protect against process media. Note The Design HP series valve uses spiral-wound gaskets which are crushed to provide their seal. A spiral-wound gasket should never be reused. Whenever a gasket seal is disturbed by removing or shifting gasketed parts, a new gasket must be installed upon reassembly. This is necessary to ensure a good gasket seal, since the used gasket will not seal properly. The spiral-wound gaskets are of special design. Failure to use Fisher replacement parts may result in valve damage. Note If the valve has ENVIRO-SEAL live-loaded packing installed (figure 4), see the Fisher instruction manual entitled ENVIRO-SEAL Packing System for Sliding Stem Valves for packing instructions. If the valve has HIGH-SEAL Heavy-Duty live-loaded packing installed (figure 4), see the Fisher instruction manual entitled

HIGH-SEAL Live-Loaded Packing System for packing instructions.

Packing Lubrication
Note To avoid lubricants breaking down at elevated temperatures, do not lubricate packing used in processes with temperatures over 260_C (500_F).

WARNING
Do not lubricate parts when used in oxygen service, or where the lubrication is incompatible with the process media. Any use of lubricant can lead to the sudden explosion of media due to the oil/oxygen mixture, causing personal injury or property damage. If a lubricator or lubricator/isolating valve (figure 2) is provided for PTFE/composition or other packings that require lubrication, it will be installed in place of the pipe plug (key 31, figure 16, 17, or 18). Use a good quality silicon-base lubricant. Packing used in oxygen service or in processes with temperatures over 260_C (500_F) should not be lubricated. To operate the lubricator, turn the cap screw clockwise to force the lubricant into the packing box. The lubricator/isolating valve operates the same way except the isolating valve must first be opened and then closed after lubrication is completed.

Packing Maintenance
If there is undesirable packing leakage in the spring-loaded PTFE V-ring packing shown in figure 3, tighten the packing flange nuts (key 21, figure 16, 17, or 18) until the shoulder on the packing follower

Instruction Manual
Form 5299 April 2004

HP and HPA Valves


31

LUBRICATOR

1. Isolate the control valve from the line pressure, release pressure from both sides of the valve body, and drain the process media from both sides of the valve. If using a power actuator, also shut-off all pressure lines to the power actuator, release all pressure from the actuator. Use lock-out procedures to be sure that the above measures stay in effect while you work on the equipment.
31

2. Remove the packing flange nuts (key 21) and lift the packing flange, upper wiper, and packing follower (keys 19, 27, and 28) away from the valve body. 3. It may be possible to dig out the old packing rings on top of the lantern ring, but use care to avoid scratching the valve plug stem or packing box wall. Clean all metal parts to remove particles that would prevent the packing from sealing. 4. Remove the stem connector and slip the packing rings over the end of the valve plug stem. 5. Reassemble the packing follower, upper wiper, packing flange, and packing flange nuts (keys 28, 27, 19, and 21). 6. Reconnect the body-actuator stem connection according to the appropriate actuator instruction manual. 7. Tighten the packing flange nuts only far enough to stop leakage under operating conditions. Check for leakage around the packing follower when the valve is being put into service. Retighten the packing flange nuts as required (see table 7).

10A9421-A AJ5428-D A0832-2/IL

LUBRICATOR/ISOLATING VALVE

Figure 2. Lubricator and Lubricator/Isolating Valve

(key 28, figure 16, 17, or 18) contacts the bonnet (key 18, figure 16, 17, or 18). If leakage continues, replace the packing by following the numbered steps presented in the replacing packing procedure. If there is undesirable packing leakage with other than spring-loaded PTFE V-ring packing, first try to limit the leakage and establish a stem seal by tightening the packing flange nuts (key 21, figure 16, 17, or 18) to at least the minimum recommended torque in table 7. However, do not exceed the maximum recommended torque in table 7 or excessive friction may result. If leakage continues, replace the packing by following the numbered steps presented in the Replacing Packing procedure. If the packing is relatively new and tight on the valve plug stem, and if tightening the packing flange nuts does not stop the leakage, it is possible that the stem is worn or nicked so that a seal cannot be made. The surface finish of a new stem is critical for making a good packing seal. If the leakage comes from the outside diameter of the packing, it is possible that the leakage is caused by nicks or scratches around the packing box wall. While replacing the packing according to the Replacing Packing procedure, inspect the valve plug stem and packing box wall for nicks or scratches.

Replacing Packing

WARNING
Refer to the WARNING at the beginning of the Maintenance section in this instruction manual. Key numbers referred to in this procedure are shown in figure 16, 17, or 18, unless otherwise indicated. 1. Isolate the control valve from the line pressure, release pressure from both sides of the valve body, and drain the process media from both sides of the valve. If using a power actuator, also shut-off all pressure lines to the power actuator, release all pressure from the actuator. Use lock-out procedures to be sure that the above measures stay in effect while you work on the equipment. 2. Remove the cap screws in the stem connector, and separate the two halves of the stem connector. Then exhaust all actuator pressure, if any was applied, and disconnect the actuator supply and any leakoff piping.

Adding Packing Rings


Key numbers referred to in this procedure are shown in figure 16, 17, or 18, unless otherwise indicated. When using packing with a lantern ring (key 24) it may be possible to add packing rings above the lantern ring as a temporary measure without removing the actuator from the valve body.

Instruction Manual

HP and HPA Valves


UPPER WIPER (KEY 27) PACKING FOLLOWER (KEY 28)

Form 5299 April 2004

PACKING FOLLOWER (KEY 28) FEMALE ADAPTOR (KEY 35) V-RING (KEY 23) MALE ADAPTOR (KEY 34) WASHER (KEY 25) SPRING (KEY 24) PACKING BOX RING (KEY 26)
12A8160-A

GRAPHITE RIBBON PACKING RING (KEY 23) KEY 22 1 GRAPHITE FILAMENT PACKING RING (KEY 23) 2 LANTERN RING (KEY 24)

PACKING BOX RING (KEY 26)


14A3412-C

PTFE V RING SINGLE PACKING


UPPER WIPER (KEY 27)

LOWER WIPER (KEY 33)

GRAPHITE RIBBON AND FILAMENT SINGLE PACKING


UPPER WIPER (KEY 27) PACKING FOLLOWER (KEY 28) PACKING RING (KEY 23)

PACKING FOLLOWER (KEY 28) FEMALE ADAPTOR (KEY 35) V-RING (KEY 23) MALE ADAPTOR (KEY 34)

PACKING FOLLOWER (KEY 28)

GRAPHITE RIBBON PACKING RING (KEY 23) GRAPHITE FILAMENT PACKING RING (KEY 23) 2 LANTERN RING (KEY 24)

KEY 22 1

LANTERN RING (KEY 24)

LANTERN RING (KEY 24)

1 PACKING BOX RING (KEY 26)


12A7839-A Sht 1

PACKING BOX RING (KEY 26)


14A3414-C 12A8163-A

PACKING BOX RING (KEY 26)

PTFE V RING DOUBLE PACKING

LOWER WIPER (KEY 33)

GRAPHITE RIBBON AND FILAMENT DOUBLE PACKING


2

PTFE/COMPOSITION DOUBLE PACKING

NOTES: 1 0.004 INCH (0.102 mm) THICK SACRIFICIAL ZINC WASHERS. USE ONLY ONE BELOW EACH GRAPHITE RIBBON RING.
C0747-1 / IL

HAS THE APPEARANCE OF A WOVEN OR BRAIDED RING.

Figure 3. Packing Arrangements

3. Remove either the yoke locknut (key 32) or the hex nuts (key 30), and remove the actuator from the bonnet (key 18). 4. Loosen the packing flange nuts (key 21) so that the packing (keys 22, 23, 209, or 210, figure 3) is not tight on the valve plug stem (key 6). Remove any travel indicator disk and stem locknuts from the valve plug stem threads.

CAUTION
When lifting the bonnet (key 18), be sure that the valve plug and stem assembly (keys 5 and 6) remains on the seat ring (key 4). This avoids damage to the seating surfaces as a

result of the assembly dropping from the bonnet after being lifted part way out. The parts are also easier to handle separately. Use care to avoid damaging gasket sealing surfaces. The Design HPD and HPAD piston rings (key 8) are brittle and in two pieces. Avoid damaging the piston rings by dropping or rough handling.

WARNING
To avoid personal injury or property damage caused by uncontrolled movement of the bonnet, loosen the

Instruction Manual
Form 5299 April 2004

HP and HPA Valves

39B4153-A

A6297-1 / IL

Typical HIGH-SEAL Graphite ULF Packing System

Typical ENVIRO-SEAL Packing System with PTFE Packing

200 STUD (KEY 200) 212 HEX NUT (KEY 212) SPRING PACK ASSEMBLY (KEY 217) GUIDE BUSHING (KEY 207) PACKING WASHERS (KEY 214) 201

213

217 PACKING FLANGE (KEY 201) PACKING RING (KEY 209) PACKING RING (KEY 210) PACKING BOX RING (KEY 211)

207 215

216 GUIDE BUSHING (KEY 208) 207 207

209 211

214

207
39B4612/A

A6722 / IL

Typical ENVIRO-SEAL Packing System with Graphite ULF Packing

Typical ENVIRO-SEAL Packing System with Duplex Packing

Figure 4. Live-Loaded Packing

Instruction Manual

HP and HPA Valves


bonnet by following the instructions in the next step. Do not remove a stuck bonnet by pulling on it with equipment that can stretch or store energy in any other manner. The sudden release of stored energy can cause uncontrolled movement of the bonnet. If the cage sticks to the bonnet, proceed carefully with bonnet removal and support the cage so that it will not fall unexpectedly from the bonnet. Note The following step also provides additional assurance that the valve body fluid pressure has been relieved. 5. Hex nuts (key 14) attach the bonnet to the valve body. Loosen these nuts or cap screws approximately 3 mm (0.125 inch). Then loosen the body-to-bonnet gasketed joint by either rocking the bonnet or prying between the bonnet and valve body. Work the prying tool around the bonnet until the bonnet loosens. If no fluid leaks from the joint, remove the nuts completely and carefully lift the bonnet and valve plug (keys 18 and 5) as a unit. 6. Unscrew the hex nuts (key 14) and carefully lift the bonnet off the valve stem. If the valve plug and stem assembly starts to lift with the bonnet, use a brass or lead hammer on the end of the stem and tap it back down. Set the bonnet on a cardboard or wooden surface to prevent damage to the bonnet gasket surface. 7. Remove the valve plug (key 5), bonnet gasket (key 11), cage (key 2), seat ring (key 4), and the seat ring gasket (key 12).

Form 5299 April 2004

9. Cover the opening in the valve body to protect the gasket surface and to prevent foreign material from getting into the valve body cavity. 10. Remove the packing flange nuts (key 21), packing flange (key 19), upper wiper (key 27), and packing follower (key 28). Carefully push out all the remaining packing parts from the valve side of the bonnet using a rounded rod or other tool that will not scratch the packing box wall. For extension bonnets, also remove the baffle (key 36 ) and retaining ring (key 37). 11. Clean the packing box and the following metal packing parts: packing follower, packing box ring (key 26), spring or lantern ring (key 24), and, for single arrangements of PTFE V-ring packing only, special washer (key 25). 12. Inspect the valve stem threads for any sharp edges that might cut the packing. A whetstone or emery cloth may be used to smooth the threads if necessary. 13. Remove the protective covering from the valve body cavity, and install the seat ring and cage using a new seat ring gasket (key 12) and bonnet gasket (key 11). Install the plug, then slide the bonnet over the stem and onto the studs (key 20). For a valve body with extension bonnet, also install the baffle and retaining rings (keys 36 and 37).

Note The prelubricated hex nuts (key 21) referred to in step 14 can be identified by a black film coating on the nut threads. The proper bolting procedures in step 14 includebut are not limited toensuring that the bonnet stud threads are clean, and that the hex nuts are evenly tightened to the specified torque values.

CAUTION
Inspect the seat ring, cage, bonnet, and body gasket surfaces. These surfaces must be in good condition, with all foreign material removed. Small burrs less than approximately 0.076 mm (0.003 inches) in height (the thickness of a human hair) can be ignored. Scratches or burrs that run across the serrations are not permitted under any conditions, since they will prevent the gaskets from sealing properly. 8. Clean all gasket surfaces with a good wire brush. Clean in the same direction as the surface serrations, not across them.

CAUTION
Failure to comply with good bonnet-to-body bolting practices and the torque values shown in table 8 may result in damage to the valve. Cheater bars or slug wrenches should not be used for this procedure. Hot torquing is not recommended.

10

Instruction Manual
Form 5299 April 2004

HP and HPA Valves


Table 9. Valve Stem Connection Torque and Drill Size for Pin Hole
VALVE STEM DIAMETER mm 12.7 19.1 12.7 Inches 0.5 0.75 0.5 0.75 1 0.5 0.75 1 0.75 1 0.75 1 1.25 HPS, HPAS HPS, HPAS HPD, HPAD, HPS, HPAS, HPT, HPAT HPS, HPAS HPD, HPAD, HPT, HPAT HPS, HPAS HPD, HPS, HPT HPD, HPS, HPT HPD, HPS, HPT HPD, HPT HPD, HPT HPD, HPT HPD, HPT HPD, HPT VALVE STEM CONNECTION TORQUE (MINIMUM-MAXIMUM) NSm LbfSft 81 - 115 237 - 339 81 - 115 237 - 339 237 - 339 420 - 481 81 - 115 237 - 339 420 - 481 237 - 339 420 - 481 237 - 339 420 - 481 827 - 908 60 - 85 175 - 250 60 - 85 175 - 250 175 - 250 310 - 355 60 - 85 175 - 250 310 - 355 175 - 250 310 - 355 175 - 250 310 - 355 610 - 670 DRILL SIZE FOR PIN Inches 0.125 0.1875 0.125 0.1875 0.125 0.25 0.125 0.1875 0.25 0.1875 0.25 0.1875 0.25 0.25

VALVE SIZE, INCHES 1

DESIGN

19.1 25.4 12.7

19.1 25.4 19.1 25.4 19.1 25.4 31.8

Note
VALVE STEM

PACKING FOLLOWER BONNET

TOP OF PACKING RING EVEN WITH BOTTOM OF ENTRANCE CHAMFER

When installing packing rings, prevent entrapping air between the rings. Add the rings one at a time without forcing them below the chamfer of the packing box entrance chamber. As each successive ring is added, the stack should not be pushed down more than the thickness of the added ring (figure 5). 15. Install new packing and the metal packing box parts according to the appropriate arrangement in figure 3. If desired, packing parts may be pre-lubricated with a silicon base grease for easier installation. Slip a smooth-edged pipe over the valve stem, and gently tamp each soft packing part into the packing box, being sure that air is not trapped between adjacent soft parts. 16. Slide the packing follower, wiper, and packing flange into position. Lubricate the packing flange studs (key 20) and the faces of the packing flange nuts (key 21). Replace the packing flange nuts. For the spring-loaded PTFE V-ring packing shown in figure 3, tighten the packing flange nuts until the shoulder on the packing follower (key 28) contacts the bonnet. For graphite packing, tighten the packing flange nuts to the maximum recommended torque shown in table 7. Then, loosen the packing flange nuts, and retighten them to the recommended minimum torque shown in table 7. For other packing types, tighten the packing flange nuts alternately in small equal increments until one

INSTALLING FIRST PACKING RING


A2207-2 / IL

INSTALLING SECOND PACKING RING

Figure 5. Installing Graphite Ribbon/Filament Packing Rings One at a Time

14. Lubricate the stud threads and the faces of the hex nuts (key 21) with Never-Seez Pure Nickel Special lubricant or equivalent (not necessary if new factory prelubricated hex nuts are used). Replace the hex nuts and tighten them finger-tight. Stroke the valve several times to center the trim. Torque the nuts in a crisscross pattern to no more than 1/4 of the nominal torque value specified in table 8. When all nuts are tightened to that torque value, increase the torque by 1/4 of the specified nominal torque and repeat the crisscross pattern. Repeat this procedure until all nuts are tightened to the specified nominal value. Apply the final torque value again and, if any nut still turns, tighten every nut again.

11

Instruction Manual

HP and HPA Valves


of the nuts reaches the minimum recommended torque shown in table 7. Then, tighten the remaining flange nuts until the packing flange is level and at a 90-degree angle to the valve stem. For ENVIRO-SEAL or HIGH-SEAL live-loaded packing, refer to the note at the beginning of the Maintenance section. 17. Mount the actuator on the valve body assembly, and reconnect the actuator and valve plug stems according to the procedures in the appropriate actuator instruction manual.

Form 5299 April 2004

5. Refer to the Valve Plug Maintenance procedure or to the Lapping Seats procedure. TSO trim: 1.6875 Inch Port Diameter (figure 8) 1. Remove the retainer, backup ring, anti-extrusion rings, and piston ring. 2. Remove the set screws that lock the outer plug to the stem. 3. Using a strap wrench or similar tool, unscrew the outer plug from the inner plug. Do not damage the outer plug guide surfaces. 4. Remove the protected soft seat seal. 5. Inspect the parts for damage and replace if needed. 6. Refer to the Valve Plug Maintenance procedure or to the Lapping Seats procedure. TSO trim: 2.6875 Inch and Larger Port Diameters (figure 9) 1. Remove the retainer, backup ring, anti-extrusion rings, and piston ring. 2. Remove the set screws that lock the outer plug to the inner plug. 3. Using a strap wrench or similar tool, unscrew the outer plug from the inner plug. Do not damage the outer plug guide surfaces. 4. Remove the protected soft seat seal. 5. Inspect the parts for damage and replace if needed. 6. Refer to the Valve Plug Maintenance procedure or to the Lapping Seats procedure.

Trim Removal
For C-seal construction, see the appropriate C-seal sections in this manual. Key numbers referenced in this procedure are shown in figure 16, 17, or 18, except where indicated. 1. Remove the actuator and bonnet by following steps 1 through 4 of the replacing packing procedure. Observe all warnings and cautions. 2. Lift the valve stem and attached valve plug out of the valve body. If the valve plug is to be reused, tape or otherwise protect the valve plug stem and the valve plug seating surface to prevent scratches. 3. Lift out the cage (key 2) and the bonnet gasket (key 11). For a 2-inch valve body with a Cavitrol III two stage cage, also remove the bonnet spacer and two gaskets.

Constructions other than TSO trim


1. Remove the seat ring (key 4) and the seat ring gasket (key 12). 2. Refer to the Valve Plug Maintenance procedure or to the Lapping Seats procedure.

TSO Trim
TSO trim: 0.8125 Inch Port Diameter (figure 7) 1. Remove the pin that locks the inner plug to the stem. 2. Using a strap wrench or similar tool, unscrew the outer plug from the inner plug. Do not damage the outer plug guide surfaces. 3. Remove the protected soft seat seal. 4. Inspect the parts for damage and replace if needed.

Valve Plug Maintenance


Key numbers used in this procedure are shown in figure 16, 17, or 18, except where indicated. 1. With the valve plug (key 5) removed according to the trim removal procedure, proceed as appropriate: For Design HPD and HPAD valves, the piston rings (key 8) are each in at least two sections; remove the sections from the grooves in the valve plug. For Design HPS and HPAS valves, proceed to step 2.

12

Instruction Manual
Form 5299 April 2004

HP and HPA Valves

INNER PLUG OUTER PLUG

CAGE

PROTECTED SOFT SEAT

SEAT RING

A7039 / IL

Figure 6. Detail of Protected Soft Seat

For Design HPT and HPAT valves, work the retaining ring (key 10) off the valve plug with a screwdriver. Carefully slide the backup ring and seal ring (keys 9 and 8) off the valve plug. 2. To replace the valve plug stem (key 6), drive out the pin (key 7), and unscrew the stem from the valve plug.

3. Thread the new stem into the valve plug and tighten it to the appropriate torque value given in table 9. Using the valve plug pin hole as a guide, drill the pin hole through the stem. Refer to table 9 for drill sizes. 4. Drive in the pin to lock the assembly. 5. If it is necessary to lap the seating surfaces, complete the lapping seats procedure before installing the Design HPD/HPAD piston rings or the Design HPT/HPAT seal ring. The Trim Replacement procedure provides piston ring and seal ring installation instructions and valve reassembly instructions.

CAUTION
Never reuse an old stem with a new valve plug. Using an old stem with a new plug requires drilling a new pin hole in the stem. This weakens the stem and may cause the stem to fail in service. If a new valve plug is required, always order a valve plug, stem, and pin as an assembly. Specify the correct part number of each of the three parts, but state that the parts are being ordered as an assembly. A used valve plug may be reused with a new stem.

Lapping Seats
Key numbers referenced in this procedure are shown in figure 16, 17, or 18, except where indicated. A certain amount of leakage should be expected with metal-to-metal seating in any valve body. If the leakage becomes excessive, however, the condition of the seating surfaces of the valve plug and seat ring can be improved by lapping. (Deep nicks should be machined out rather than ground out.) Use a

13

Instruction Manual

HP and HPA Valves

Form 5299 April 2004

OUTER PLUG

PIN

INNER PLUG

PROTECTED SOFT SEAT

A7111 / IL

Figure 7. Typical Unbalanced TSO Trim Assembly, Small Port Designs (0.8125 Inch Port Diameter)

good quality lapping compound of a mixture of 280 to 600-grit. Apply the compound to the bottom of the valve plug. Note The Design HP Series valves use spiral-wound gaskets. These gaskets provide their seal by being crushed and therefore should never be reused. This includes reusing a gasket after

the lapping procedure has been performed. An old gasket can be used to lap the seat, however the gasket must be replaced with a new gasket. To preserve the effects of lapping, do not change either the position of the seat ring in the valve body cavity or the position of the cage on the seat ring after lapping the seating surfaces. When the parts are removed for

14

Instruction Manual
Form 5299 April 2004

HP and HPA Valves

VALVE PLUG SEAL

VALVE PLUG SEAL

PROTECTED SOFT SEAT


A7096 / IL A7112 / IL

PROTECTED SOFT SEAT

Figure 8. Typical Balanced TSO Trim (1.6875 Inch Port Diameter)

Figure 9. Typical Balanced TSO Trim, Large Port Designs (2.6875 Inch and Larger Port Diameters)

cleaning and replacement of the old gaskets, return them to the original positions. Use the following procedure to lap the seating surfaces. 1. Install the following parts according to the instructions presented in the trim replacement procedure: old seat ring gasket (key 12), seat ring (key 4), cage (key 2), and old bonnet gasket (key 11). 2. Proceed as appropriate: For a Design HPD, HPAD, HPT, or HPAT valve, install the valve plug and stem assembly (keys 5 and 6)without piston rings or seal ring (key 8)into the cage.

For a Design HPS or HPAS valve, install the valve plug and stem assembly (keys 5 and 6) into the cage. 3. Install the bonnet (key 18) over the valve stem, and secure the bonnet with four of the hex nuts (key 14). 4. Attach a handle, such as a piece of strap iron secured by stem locknuts, to the valve stem. Rotate the handle alternately in each direction to lap the seats. 5. After lapping, disassemble as necessary (you may mark the position of the seat ring and cage with a soft tip marker). Clean the seating surfaces, replace the gaskets, reassembly (taking care to return the seat ring and cage to their original positions), and test for shutoff. Repeat the lapping procedure if necessary.

15

Instruction Manual

HP and HPA Valves


Table 10. Actuator Groups by Type Number
Group 1 71 & 90 mm (2.8125 & 3.5625 Inch) Yoke Boss 350Except 90 mm (3.5625 inch) Yoke Boss 472 & 473 585C 603 & 1B 644 & 645 655 657 & 667 1008 Group 100 127 mm (5-Inch) Yoke Boss 350 472 473 474 476 585C 657 Group 101 127 mm (5-Inch) Yoke Boss 667

Form 5299 April 2004

Trim Replacement WARNING


Observe the warning at the start of the Maintenance section. After all trim maintenance has been completed, reassemble the valve body by following the numbered steps below. Be certain that all gasketed surfaces have been well cleaned. Key numbers referenced in this procedure are shown in figure 16, 17, or 18, except where indicated.

halves. Place the new ring in the vise so that the jaws compress the ring into an oval. Compress the ring slowly until the ring snaps on both sides. If one side snaps first, do not try to tear or cut the other side. Instead, keep compressing until the other side snaps. The piston ring can also be fractured by scoring and snapping over a hard surface such as a table edge. Sawing or cutting is not recommended. Remove any protective tape or covering from the valve plug and stem assembly, and set it on a protective surface. Then, place the piston rings in the piston ring grooves with the fractured ends matched. For a Design HPT or HPAT valve, install the seal ring (key 8) onto the valve plug (key 5). Install the ring with the open side facing the seat ring end of the valve plug for flow-down applications (view A of figure 19) or with the open side facing the valve plug stem end of the valve plug for flow-up applications (view B of figure 19). Slide the backup ring (key 9) onto the valve plug. Secure with the retaining ring (key 10). 2. Install the valve plug into the cage.

CAUTION
Inspect the seat ring, cage, bonnet, and body gasket surfaces. These surfaces must be in good condition, with all foreign material removed. Small burrs less than approximately 0.076 mm (0.003 inches) in height (the thickness of a human hair) can be ignored. Scratches or burrs that run across the serrations are not permitted under any conditions, since they will prevent the gaskets from sealing properly. 1. Install the seat ring gasket (key 12) into the valve body. Install the seat ring (key 4). 2. Install the cage.

TSO Trim
TSO trim: 0.8125 Inch Port Diameter (figure 7) 1. Thread the outer plug onto the inner plug until the parts seat metal to metal, using a strap wrench or similar tool that will not damage the outer plug guide surfaces. 2. Mark the inner plug and outer plug with alignment marks in the assembled position. 3. Disassemble the outer plug from the inner plug and install the seal over the inner plug, so that the seal rests below the threaded area. 4. Thread the outer plug onto the inner plug and tighten with a strap wrench or similar tool until the

Constructions other than TSO trim


1. To install the piston rings and seal rings (key 8), proceed as appropriate: For a Design HPD or HPAD valve, if it is necessary to install new piston rings, the replacement piston rings will arrive in one piece. Use a vise with smooth or taped jaws to break a replacement piston ring into

16

Instruction Manual
Form 5299 April 2004

HP and HPA Valves


compressed properly. Do not damage the outer plug guide surfaces. 5. Install set screws centering the inner plug in the outer plug and torque to 11 NSm (8 lbfSft). 6. Assemble the piston ring, anti-extrusion rings, backup ring, and retainer.

alignment marks line up. This will ensure that the plug parts are metal to metal and the seal is compressed properly. Do not damage the outer plug guide surfaces. 5. Drill through the inner plug with the proper size drill bit (same size as stem pinning) and install the pin. TSO trim: 1.6875 Inch Port Diameter (figure 8) 1. Thread the outer plug onto the inner plug until the parts seat metal to metal, using a strap wrench or similar tool that will not damage the outer plug guide surfaces. 2. Mark the top of the outer plug and stem with alignment marks in the assembled position. 3. Disassemble the outer plug from the inner plug and install the seal over the inner plug, so that the seal rests below the threaded area. 4. Thread the outer plug onto the inner plug and tighten with a strap wrench or similar tool until the alignment marks line up. This will ensure that the plug parts are metal to metal and the seal is compressed properly. Do not damage the outer plug guide surfaces. 5. Install set screws centering the stem in the outer plug and torque to 11 NSm (8 lbfSft). 6. Assemble the piston ring, anti-extrusion rings, backup ring, and retainer. TSO trim: 2.6875 Inch and Larger Port Diameters (figure 9) 1. Thread the outer plug onto the inner plug until the parts seat metal to metal, using a strap wrench or similar tool that will not damage the outer plug guide surfaces. 2. Mark the top of the inner plug and outer plug with alignment marks in the assembled position. 3. Disassemble the outer plug from the inner plug and install the seal over the inner plug, so that the seal rests below the threaded area. 4. Thread the outer plug onto the inner plug and tighten with a strap wrench or similar tool until the alignment marks line up. This will ensure that the plug parts are metal to metal and the seal is

All Constructions
1. Install the bonnet gasket (key 11) on the cage. 2. Install the bonnet over the valve stem and onto the valve body. Note The prelubricated hex nuts (key 14) referred to in step 7 can be identified by a black film coating on the nut threads. The proper bolting procedures in step 7 includebut are not limited toensuring that the bonnet stud threads are clean, and that the hex nuts are evenly tightened to the specified torque values.

CAUTION
Failure to comply with good bonnet-to-body bolting practices and the torque values shown in table 8 may result in damage to the valve. Cheater bars or slug wrenches should not be used for this procedure. Hot torquing is not recommended. 3. Lubricate the stud threads and the faces of the hex nuts (key 14) with Never-Seez Pure Nickel Special lubricant or equivalent (not necessary if new factory prelubricated hex nuts are used). Replace the hex nuts, but do not tighten them. Torque the nuts in a crisscross pattern to no more than 1/4 of the nominal torque value specified in table 8. When all nuts are tightened to that torque value, increase the torque by 1/4 of the specified nominal torque and repeat the crisscross pattern. Repeat this procedure until all nuts are tightened to the specified nominal value. Apply the final torque value again and, if any nut still turns, tighten every nut again. 4. Install new packing and packing box part per steps 12 and 13 of the Replacing Packing procedure. Be certain to observe the note given prior to step 12 of that procedure.

17

Instruction Manual

HP and HPA Valves

Form 5299 April 2004

FLOW DOWN

FLOW UP

VIEW A
37B1399-A / IL

Figure 10. Design HPD with C-seal Trim

5. Mount the actuator by following the procedures in the actuator instruction manual. Check for packing leakage as the valve is being put into service. Retorque the packing flange nuts as required (see table 7).

where the C-seal plug seal must be pressed into the proper sealing position (figure 10). 2. Orient the C-seal plug seal for correct sealing action based on the process fluid flow direction through the valve. D The open interior of the C-seal plug seal must face up in a valve with flow-up construction (figure 10). D The open interior of the C-seal plug seal must face down in a valve with flow-down construction (figure 10). Note An installation tool must be used to properly position the C-seal plug seal on the valve plug. A tool is available as a spare part from Fisher or a tool could be manufactured following the dimensions given in figure 11. 3. Place the C-seal plug seal over the top of the valve plug and press the C-seal plug seal onto the plug using the C-seal installation tool. Carefully press the C-seal plug seal onto the plug until the installation tool contacts the horizontal reference surface of the valve plug (figure 12). 4. Apply a suitable high-temperature lubricant to the threads on the plug. Then, place the C-seal retainer onto the plug and tighten the retainer using an appropriate tool such as a strap wrench. 5. Using an appropriate tool such as a center punch, stake the threads on top of the plug in one place (figure 13) to secure the C-seal retainer.

Retrofit: Installing C-seal Trim


Note Additional actuator thrust is required for a valve with C-seal trim. When installing C-seal trim in an existing valve, contact your Fisher sales office for assistance in determining new actuator thrust requirements. Assemble the new valve plug/retainer assembly (with C-seal plug seal) using the following instructions:

CAUTION
To avoid leakage when the valve is returned to service, use appropriate methods and materials to protect all sealing surfaces of the new trim parts while assembling the individual parts and during installation in the valve body. 1. Apply a suitable high-temperature lubricant to the inside diameter of the C-seal plug seal. Also, lubricate the outside diameter of the valve plug

18

Instruction Manual
Form 5299 April 2004

HP and HPA Valves


DIMENSIONS, INCHES (See Drawing Below) A 3.25 4.00 4.11 4.96 5.62 7.25 8.25 B C D E 1.62 2.00 2.00 2.00 1.81 2.37 2.20 F G H 2.791 - 2.797 3.353 - 3.359 3.541 - 3.547 4.291 - 4.297 5.048 - 5.054 6.674 - 6.680 7.674 - 7.680 PART NUMBER (To Order A Tool) 24B9816X012 24B5612X012 24B3630X012 24B3635X012 23B9193X012 23B9180X012 24B9856X012

FOR VALVE PLUGS FITTING PORT SIZE (Inches) 2.875 3.4375 3.625 4.375 5.375 7 8

2.060 - 2.070 0.196 - 0.198 0.146 - 0.148 2.310 - 2.320 0.196 - 0.198 0.146 - 0.148 2.560 - 2.570 0.196 - 0.198 0.146 - 0.148 3.285 - 3.295 0.196 - 0.198 0.146 - 0.148 3.940 - 3.950 0.196 - 0.198 0.146 - 0.148 5.566 - 5.576 0.196 - 0.198 0.146 - 0.148 6.566 - 6.576 0.196 - 0.198 0.146 - 0.148

2.074 - 2.078 2.170 - 2.190 2.402 - 2.406 2.498 - 2.518 2.714 - 2.718 2.810 - 2.830 3.439 - 3.443 3.535 - 3.555 4.088 - 4.092 4.184 - 4.204 5.714 - 5.718 5.810 - 5.830 6.714 - 6.718 6.810 - 6.830

A B 45 X 0.06

8 - 9 E

F G H
A6777 / IL

45 X 0.02 BREAK SHARP CORNER 45 X 0.01 MAX

Figure 11. C-seal Plug Seal Installation Tool

6. Install the new plug/retainer assembly with C-seal plug seal on the new stem following the appropriate instructions in the Trim Replacement section in this manual. 7. Install piston rings by following instructions in the Trim Replacement section in this manual. 8. Remove the existing valve actuator and bonnet following the appropriate instructions in the Replacing Packing section in this manual.

Never reuse an old valve stem with a new plug or reinstall a valve stem after it has been removed. Replacing a valve stem requires drilling a new pin hole in the stem. This drilling weakens the stem and may cause failure in service. However, a used valve plug may be reused with a new valve stem. 9. Remove the existing valve stem and plug, cage, and seat ring from the valve body following the appropriate instructions in the Trim Removal section in this manual. 10. Replace all gaskets according to appropriate instructions in the Trim Replacement section in this manual.

CAUTION
Do not remove the existing valve stem from the valve plug unless you are planning to replace the valve stem.

19

Instruction Manual

HP and HPA Valves


DEFORM THREAD TO STAKE C-SEAL RETAINER

Form 5299 April 2004

INSTALLATION TOOL

PISTON RING

C-SEAL METAL PLUG SEAL

RETAINER VALVE PLUG

A6778/IL

HORIZONTAL REFERENCE SURFACE

C-SEAL METAL PLUG SEAL

VALVE PLUG

FLOW DOWN
NOTE: PRESS THE INSTALLATION TOOL OVER THE VALVE PLUG UNTIL THE TOOL CONTACTS THE HORIZONTAL REFERENCE SURFACE OF THE VALVE PLUG.
A6779 / IL

FLOW DOWN

Figure 13. Stake the Threads of the C-seal Retainer

Figure 12. Installing the C-seal Plug Seal Using the Installation Tool

assembly, the cage, and the seat ring become a matched set. 11. Install the new seat ring, cage, valve plug/retainer assembly, and stem into the valve body and completely reassemble the valve package following the appropriate instructions in the Trim Replacement section in this manual. With full actuator force applied and the valve plug fully seated, align the actuator travel indicator scale with the lower end of valve travel. Refer to the appropriate actuator instruction manual for information on this procedure.

CAUTION
To avoid excessive leakage and seat erosion, the valve plug must be initially seated with sufficient force to overcome the resistance of the C-seal plug seal and contact the seat ring. You can correctly seat the valve plug by using the same force calculated for full load when sizing your actuator. With no pressure drop through the valve, this force will adequately drive the valve plug to the seat ring, thus giving the C-seal plug seal a predetermined permanent set. Once this is done, the plug/retainer

Replacement of Installed C-seal Trim


Trim Removal (C-seal Constructions)
1. Remove the valve actuator and bonnet following the appropriate instructions in the Replacing Packing section in this manual.

CAUTION
To avoid leakage when the valve is returned to service, use appropriate methods and materials to protect all sealing surfaces of the trim parts during maintenance.

20

Instruction Manual
Form 5299 April 2004

HP and HPA Valves


RETAINER

Use caution when removing piston ring(s) and C-seal plug seal to avoid scratching any sealing surface.

CAUTION
Do not remove the valve stem from the plug/retainer assembly unless you are planning to replace the valve stem. Never reuse an old valve stem with a new plug or reinstall a valve stem after it has been removed. Replacing a valve stem requires drilling a new pin hole in the stem. This drilling weakens the stem and may cause failure in service. However, a used valve plug may be reused with a new valve stem. 2. Remove the plug/retainer assembly (with C-seal plug seal), cage, and seat ring from the valve body following the appropriate instructions in the Trim Removal section in this manual. 3. Locate the staked thread on top of the valve plug (figure 13). The staked thread secures the retainer. Use a drill with a 0.125 inch bit to drill out the staked area of the thread. Drill approximately 1/8-inch into the metal to remove the staking. 4. Locate the break between sections of the piston ring(s). Using an appropriate tool such as a flat-blade screwdriver, carefully pry out the piston ring(s) from the groove(s) in the C-seal retainer. 5. After removing the piston ring(s), locate the 0.25-inch diameter hole in the groove. In a retainer with two piston ring grooves, the hole will be found in the upper groove. 6. Select an appropriate tool such as a punch and place the tip of the tool into the hole with the body of the tool held tangent to the outside diameter of the retainer. Strike the tool with a hammer to rotate the retainer and free it from the valve plug. Remove the retainer from the plug. 7. Use an appropriate tool such as a flat-blade screwdriver to pry the C-seal plug seal off the plug. Use caution to avoid scratches or other damage to the sealing surfaces where the C-seal plug seal makes contact with the valve plug (figure 14). 8. Inspect the lower seating surface where the valve plug contacts the seat ring for wear or damage which would prevent proper operation of the valve. Also, inspect the upper seating surface inside the cage where the C-seal plug seal contacts the cage, and inspect the sealing surface where the C-seal plug seal makes contact with the plug (figure 14).
NOTE:
1 UPPER SEATING SURFACE IS THE AREA OF CONTACT BETWEEN THE C-seal METAL PLUG SEAL AND THE CAGE. C-seal METAL PLUG SEAL 1

VALVE PLUG

CAGE

UPPER SEATING SURFACE

CAGE
PLUG

SEAT RING

LOWER SEATING SURFACE

A6780/IL

Figure 14. Lower (Valve Plug to Seat Ring) and Upper (C-seal Plug Seal to Cage) Seating Surfaces

9. Replace or repair trim parts according to the following procedure for Lapping Metal Seats, Remachining Metal Seats, or other valve plug maintenance procedures as appropriate.

Lapping Metal Seats (C-seal Constructions)


Before installing a new C-seal plug seal, lap the lower seating surface (valve plug to seat ring, figure 14) following appropriate procedures in the Lapping Seats section in this manual.

Remachining Metal Seats (C-seal Constructions)


See figure 15. A valve plug with a C-seal metal plug seal features two seating surfaces. One seating surface is found where the valve plug contacts the seat ring. The second seating surface is found where the C-seal plug seal contacts the upper seating surface in the cage. If you machine the seats on the seat ring and/or plug, you must machine an equal dimension from the seating area in the cage.

21

Instruction Manual

HP and HPA Valves


C-seal RETAINER

Form 5299 April 2004

where the C-seal plug seal must be pressed into the proper sealing position (figure 10). 2. Orient the C-seal plug seal for correct sealing action based on the process fluid flow direction through the valve. D The open interior of the C-seal plug seal must face up in a valve with flow-up construction (figure 10). D The open interior of the C-seal plug seal must face down in a valve with flow-down construction (figure 10). Note An installation tool must be used to properly position the C-seal plug seal on the valve plug. A tool is available as a spare part from Fisher or a tool could be manufactured following the dimensions given in Figure 11. 3. Place the C-seal plug seal over the top of the valve plug and press it onto the plug using the installation tool. Carefully press the C-seal plug seal onto the plug until the installation tool contacts the horizontal reference surface of the valve plug (figure 12). 4. Apply a suitable high-temperature lubricant to the threads on the plug. Then, place the C-seal retainer onto the plug and tighten the retainer using an appropriate tool such as a strap wrench. 5. Using an appropriate tool such as a center punch, stake the threads on top of the plug in one place (figure 13) to secure the C-seal retainer. 6. Replace the piston rings following instructions in the Trim Replacement section in this manual.

UPPER SEATING SURFACE 0.020 INCH(4) 3

PLUG

MACHINING OF THE UPPER SEATING SURFACE MUST EQUAL THE TOTAL MACHINING OF THE LOWER SEATING SURFACE (PLUG PLUS SEAT RING). IF NOT, THE RETAINER MAY STRIKE THE UPPER SEATING SURFACE BEFORE THE VALVE PLUG PROPERLY SEATS ON THE LOWER SEATING SURFACE.

0.010 INCH(4)

CAGE

SEAT RING

0.010 INCH(4)

LOWER SEATING SURFACE


NOTE: 1 REMOVAL OF 0.010 INCH FROM THE VALVE PLUG PLUS 2 REMOVAL OF 0.010 INCH FROM THE SEAT RING MUST EQUAL 3 REMOVAL OF 0.020 INCH FROM THE UPPER SEATING

SURFACE IN THE CAGE


4. THESE VALUES ARE FOR EXAMPLE ONLY. REMOVE ONLY THE MINIMUM AMOUNT OF MATERIAL REQUIRED TO REFURBISH THE SEATS.

A6781 /IL

Figure 15. Example of Machining the Lower (Valve Plug to Seat Ring) and Upper (C-seal Plug Seal to Cage) Seating Surfaces

CAUTION
If metal is removed from the seat ring and plug and a corresponding amount is not removed from the cage seating area, the C-seal plug seal will be crushed as the valve closes and the C-seal retainer will strike the seating area of the cage, preventing the valve from closing.

7. Return the seat ring, cage, plug/retainer assembly, and stem to the valve body and completely reassemble the valve package following the appropriate instructions in the Trim Replacement section in this manual.

CAUTION
To avoid excessive leakage and seat erosion, the valve plug must be initially seated with sufficient force to overcome the resistance of the C-seal plug seal and contact the seat ring. You can correctly seat the valve plug by using the same force calculated for full load when sizing your actuator. With no pressure drop through the

Trim Replacement (C-seal Constructions)


1. Apply a suitable high-temperature lubricant to the inside diameter of the C-seal plug seal. Also, lubricate the outside diameter of the valve plug

22

Instruction Manual
Form 5299 April 2004

HP and HPA Valves


for technical assistance or when ordering replacement parts. When ordering replacement parts, also be sure to include the 11-character part number for each part required from the following parts list. Note Use only genuine Fisher replacement parts. Components that are not supplied by Fisher should not, under any circumstances, be used in any Fisher valve, because they will void your warranty, might adversely affect the performance of the valve, and might jeopardize worker and workplace safety. Note

valve, this force will adequately drive the valve plug to the seat ring, thus giving the C-seal plug seal a predetermined permanent set. Once this is done, the plug/retainer assembly, the cage, and the seat ring become a matched set. With full actuator force applied and the valve plug fully seated, align the actuator travel indicator scale with the lower end of valve travel. Refer to the appropriate actuator instruction manual for information on this procedure.

Parts Ordering
Each body-bonnet assembly is assigned a serial number, which can be found on the valve body. This same number also appears on the actuator nameplate when the valve body is shipped from the factory as part of a control valve assembly. Refer to the number when contacting your Fisher sales office

Fisher does not assume responsibility for the selection, use, or maintenance of any product. Responsibility for proper selection, use, and maintenance of any Fisher product remains solely with the purchaser and end-user.

23

Instruction Manual

HP and HPA Valves


Parts Kits
Packing Kits (non live-loaded)
Stem Diameter, mm (Inches) Yoke Boss Diameter, mm (Inches) PTFE (Contains keys 22, 24, 25, 26, 27) Double PTFE (Contains keys 22, 24, 26, 27) PTFE/Composition (Contains keys 23, 24, 25, 26) Single Graphite Ribbon/Filament (Contains keys 23, 23, 24, 26) Double Graphite Ribbon/Filament (Contains keys 23, 23, 24, 26) 12.7 (0.5) 71 (2.8125) RPACKX00022 RPACKX00052 RPACKX00082 RPACKX00112 RPACKX00172

Form 5299 April 2004

19.1 (0.75) 90 (3.5625) RPACKX00032 RPACKX00062 RPACKX00092 RPACKX00122 RPACKX00182

Repair Kits (ENVIRO-SEAL)


Stem Diameter, mm (Inches) Yoke Boss Diameter, mm (Inches) Double PTFE (Contains keys 214, 215, 218) Graphite ULF (Contains keys 207, 208, 209, 210, 214) Duplex (Contains keys 207, 209, 214, 215) 12.7 (0.5) 71 (2.8125) RPACKX00202 RPACKX00602 RPACKX00302 19.1 (0.75) 90 (3.5625) RPACKX00212 RPACKX00612 RPACKX00312 25.4 (1) 127 (5) RPACKX00222 RPACKX00622 RPACKX00322 31.8 (1.25) 127 (5, 5H) RPACKX00232 RPACKX00632 RPACKX00332

Retrofit Kits (ENVIRO-SEAL)


Stem Diameter, mm (Inches) Yoke Boss Diameter, mm (Inches) Double PTFE (Contains keys 200, 201, 211, 212, 214, 215, 216, 217, 218, tag, cable tie) Graphite ULF (Contains keys 200, 201, 207, 208, 209, 210, 211, 212, 214, 217, tag, cable tie) Duplex (Contains keys 200, 201, 207, 209, 211, 212, 214, 215, 216, 217, tag, cable tie) 12.7 (0.5) 71 (2.8125) RPACKXRT022 RPACKXRT272 RPACKXRT222 19.1 (0.75) 90 (3.5625) RPACKXRT032 RPACKXRT282 RPACKXRT232 25.4 (1) 127 (5) RPACKXRT042 RPACKXRT292 RPACKXRT242 31.8 (1.25) 127 (5, 5H) RPACKXRT052 RPACKXRT302 RPACKXRT252

Parts List
Numerous available combinations of valve parts make selection of some parts difficult; when ordering valve parts for which a part number is not listed, provide the valve serial number with the order, permitting proper selection of replacement parts to be made at the factory.

Key 10*

Note Part numbers are shown for recommended spares only. For part numbers not shown, contact your Fisher sales office. Key 1 Description Valve Body If you need a valve body as a replacement part, order by valve size, serial number, and desired material. Cage/Baffle Assy Bonnet Spacer Seat Ring Valve Plug Valve Stem Pin Seal Ring/Piston Ring Back Up Ring Part Number ---

2* 3 4* 5* 6* 7* 8* 9*

See following table See following table See following table See following table See following table See following table See following table

11* 12* 13 14 15 16 17

Description Part Number Retaining Ring (for Design HPT/HPAT only) S30200 (302 SST) For 38.1 mm (1.5 inch) port diameter 13A8519X012 For 47.6 mm (1.875 inch) port diameter 10A4220X012 For 63.5 mm (2.5 inch) port diameter 17A4311X012 For 73.0 mm (2.875 inch) port diameter 10A4219X012 For 87.3 mm (3.4375 inch) port diameter 10A5350X012 For 98.4 mm (3.625 inch) port diameter 16A5484X012 For 111.1 mm (4.375 inch) port diameter 10A4225X012 For 115.8 mm (4.5625 inch) port diameter 17A4415X012 For 133.4 mm (5.25 inch) port diameter 17A4398X012 For 136.5 mm (5.375 inch) port diameter 10A5410X012 N07750 (Inconel X750) for NACE For 38.1 mm (1.5 inch) port diameter 13A8519X032 For 47.6 mm (1.875 inch) port diameter 10A4220X082 For 63.5 mm (2.5 inch) port diameter 17A4311X032 For 73.0 mm (2.875 inch) port diameter 10A4219X082 For 87.3 mm (3.4375 inch) port diameter 10A5350X082 For 98.4 mm (3.625 inch) port diameter 16A5484X052 For 111.1 mm (4.375 inch) port diameter 10A4225X062 For 115.8 mm (4.5625 inch) port diameter 17A4415X032 For 133.4 mm (5.25 inch) port diameter 17A4398X042 For 136.5 mm (5.375 inch) port diameter 10A5410X052 Bonnet Gasket See following table Seat Ring Gasket See following table Stud, Cont Thd Hex Nut Lubricant (Never-Seez Nickel Special 8 lb [3.6 Kg] can) Nameplate Wire

24

*Recommended spare parts

Instruction Manual
Form 5299 April 2004

HP and HPA Valves

FLOW UP KEY 31 AND TAPPING ARE OPTIONAL

FLOW DOWN

FLOW j APPLY LUB FLOW

52B6054-B

DESIGN HPS TRIM MICRO FORM PLUG

DESIGN HPS TRIM MICRO FLUTE PLUG

Figure 16. Size 1 Design HPS Valve


Key 18 Description Bonnet--If you need a bonnet as a replacement part, order by valve size and stem diameter, serial number, and desired material. Packing Flange Stud Bolt Hex Nut Packing Set Packing Ring Spring or Lantern Ring Washer, Special Packing Box Ring Upper Wiper Follower Stud Bolt Hex Nut Pipe Plug (optional) Lubricator (optional) Lubricator/Isolating Valve (optional) Yoke Locknut (optional) Baffle Retaining Ring Drive Screw Part Number Key 39* 40 41 63* Description Piston Ring Washer Flow Arrow Anti-Extrusion Ring Part Number See following table

See following table

19 20 21 22* 23* 24 25 26* 27* 28 29 30 31 31 31 32 36 37 38

C-seal Trim (figure 10)


See following table See following table 2* 4* 5* 6* 8* 64* Cage Seat Ring Valve Plug/Retainer Valve Plug Stem, Nitronic 50 Piston Ring, graphite (2 reqd) C-seal, Inconel See following table See following table See following table See following table See following table See following table

See following table See following table

TSO Trim (figures 7, 8, and 9)


2* 4* 5* 8* 63* 9* 10* Cage Seat Ring Plug/Stem Assembly Seal Ring Anti-Extrusion Ring Back Up Ring Retaining Ring See following table See following table See following table See following table See following table See following table See following table

*Recommended spare parts

25

Instruction Manual

HP and HPA Valves

Form 5299 April 2004

KEY 31 AND TAPPING ARE OPTIONAL

FLOW UP

FLOW DOWN

53B6657 / IL

FLOW

53B6655 / IL

FLOW

DESIGN HPAD

DESIGN HPAS MICRO FLAT PLUG

Figure 17. Size 2 HPAD Valve

26

Instruction Manual
Form 5299 April 2004

HP and HPA Valves

KEY 31 AND TAPPING ARE OPTIONAL

FLOW

j APPLY LUB

DESIGN HPD TRIM


FLOW UP FLOW DOWN

EXTENSION BONNET BAFFLE ASSEMBLY (SIZE 2 ONLY) (GLOBE & ANGLE)

127 mm (5 INCH) YOKE BOSS (GLOBE & ANGLE)


52B6045-C / IL

Figure 18. Size 2-6 Design HPD Valve

27

Instruction Manual

HP and HPA Valves

Form 5299 April 2004

FLOW

DESIGN HPT TRIM (ALL SIZES)

2" 3" DESIGN HPS TRIM

FLOW

FLOW

DESIGN HPS TRIM MICRO FORM PLUG (2" ONLY)

FLOW

FLOW

FLOW

2" DESIGN HPT TRIM 2 STAGE CAVITROL III

2" DESIGN HPS TRIM 3 STAGE CAVITROL III

3" 6" DESIGN HPT TRIM 2 STAGE CAVITROL III

VIEW A

FLOW

3" 6" DESIGN HPT TRIM 3 STAGE CAVITROL III


52B6045-C / IL

21B2120-A A6137 / IL

FLOW UP

FLOW DOWN

2" 6" DESIGN HPT USING PEEK ANTI EXTRUSION RINGS

Figure 19. Size 2-6 Design HP Valve - Alternate Configurations

28

Instruction Manual
Form 5299 April 2004

HP and HPA Valves

FLOW

FLOW

DESIGN HPT TRIM WHISPER III, AVAILABLE IN DESIGN HPD (2" 6") AND DESIGN HPS (2" 3")

4" DESIGN HPD TRIM WHISPER III LEVEL D

FLOW

4" DESIGN HPT TRIM WHISPER III LEVEL D

FLOW

6" DESIGN HPT TRIM WHISPER III LEVEL D

VIEW B

FLOW

52B6045-C / IL

6" DESIGN HPD TRIM WHISPER III LEVEL D

Figure 19. Size 2-6 Design HP Valve - Alternate Configurations (Continued)

29

Instruction Manual

HP and HPA Valves


Keys 22*, 23*, 27*, 33*, 34*, and 35* Soft Packing Parts PACKING ARRANGEMENT PTFE KEY NUMBER 22 PACKING PART DESCRIPTION Packing set (1 reqd for single, 2 reqd for double)(1) [includes keys 23, 33, 34, and 35] Upper Wiper Graphite Ribbon Ring (2 reqd) Graphite Filament Ring [2 reqd for 12.7 mm (0.5 inch) stem; 3 reqd for all others] Graphite Ribbon Ring (3 reqd) Graphite Filament Ring [4 reqd for 12.7 mm (0.5 inch) stem; 5 reqd for all others] Packing Ring [10 reqd for 12.7 mm (0.5 inch) stem; 8 reqd for all others] Upper Wiper VALVE STEM SIZE 12.7 mm (0.5 Inch) 19.1 mm (0.75 Inch) 25.4 mm (1-Inch) 1R290201012 1R290401012 1R290601012

Form 5299 April 2004

31.8 mm (1.25 Inch) 1R290801012

27 Low chloride graphite ribbon and filament, single 23 23

1J872706332 1V3802X0022 1E3190X0222

1J872806332 1V2396X0022 1E3191X0282

1J872906332 1U6768X0022 1D7518X0132

1J873006332 1V5666X0022 1D7520X0162

Low chloride graphite ribbon and filament, double

23 23

1V3802X0222 1E3190X0222

1V2396X0022 1E3191X0282

1U6768X0022 1D7518X0132

1V5666X0022 1D7520X0162

PTFE/composition, double

23

1E3199001042

1E319101042

1D7518X0012

1D7520X0012

27

1J872706332

1J872806332

1J872906332

1J873006332

*Recommended spare part. 1. Key 22 for double construction contains one extra Lower Wiper for all stem sizes. Discard upon assembly.

Key 26* Packing Box Ring QUANTITY REQUIRED PACKING TYPE Single Packing 1 1 1 1 1 1 1 1 --------Double Packing 1 1 1 1 1 1 1 1 1 1 1 1 VALVE STEM CONNECTION mm 12.7 19.1 25.4 31.8 12.7 19.1 25.4 31.8 12.7 19.1 25.4 31.8 Inches 0.5 0.75 1 1.25 0.5 0.75 1 1.25 0.5 0.75 1 1.25 MATERIAL S31600 (316) Stainless Steel 1J873235072 1J873335072 1J873435072 1J873535072 1J873235072 1J873335072 1J873435072 1J873535072 1J873235072 1J873335072 1J873435072 1J873535072

PTFE V-Ring

Low Chloride Graphite Ribbon and Filament

PTFE/Composition

Key 2* Cage for Valves Without Whisper Trim III Cage or Cavitrol III Trim VALVE SIZE, INCHES 1 2 3 4 6 CAGE DESCRIPTION Quick opening Equal percentage Linear Equal percentage Linear Equal percentage Linear Equal percentage Linear TRAVEL mm 29 29, 38 38 38, 51 51 38, 51 51 64, 76 76 Inches 1.125 1.125, 1.5, 1.5 1.5, 2 2 1.5, 2 2 2.5, 3 3 S17400 (17-4 SST) w/H1075 Heat Treatment 22B6047X012 32B6028X012 32B6025X012 42B8240X012 42B8242X012 42B9320X012 42B9322X012 43B0261X012 43B0079X012 MATERIAL SA-182-F22 Ion Nitride 22B6047X022 32B6028X022 32B6025X022 42B8240X022 42B8242X022 42B9320X022 42B9322X022 43B0261X022 43B0079X022 S31600 (316 Stainless Steel) Electrolized 22B6048X012 32B6029X012 32B6026X012 42B8241X012 42B8243X012 42B9321X012 42B9323X012 43B0080X012 43B0081X012 NACE MR0175 S17400 H1150 DBL 22B6047X032 32B6028X032 32B6025X032 42B8240X032 42B8242X032 42B9320X032 42B9322X032 43B0261X032 43B0079X032

30

*Recommended spare parts

Instruction Manual
Form 5299 April 2004

HP and HPA Valves


MATERIAL TRAVEL PORT DIAMETER mm 0.75 0.75 1 1.25 1.5 19, 29 19, 29 19, 29 19, 29 29, 38 Inches 0.75, 1.125 0.75, 1.125 0.75, 1.125 0.75, 1.125 1.125, 1.5 S17400 (17-4 SST) w/H1075 Heat Treatment 23B6618X012 33B6642X012 33B6628X012 33B6631X012 32B4234X012 SA-182-F22 Ion Nitride 23B6618X022 33B66420X22 33B6628X022 33B6631X022 32B4234X022 S31600 (316 Stainless Steel) Electrolized 23B6619X012 33B6643X012 31B2079X012 31B2080X012 31B2086X012

Key 2* Cage for Angle Valves with Restricted Port Equal Percentage Trim VALVE SIZE, INCHES 1 Class 1500 NACE MR017590 S17400 H1150 DBL 23B6618X032 33B6642X032 33B6628X032 33B6631X032 32B4234X032

VALVE RATING

Key 2* Cage or Cage and Baffle Assembly for Valves with Whisper Trim III Cage MATERIAL VALVE RATING VALVE SIZE, INCHES PORT DIAMETER CAGE DESCRIPTION mm 2 3 Level A1 Level A1 Level B1 Level A1 Level A3 Level B3 Level C3 Level D3(1) Level A1 Level B3 Level C3 Level D3(1) 47.6 73.0 73.0 92.1 92.1 92.1 92.1 73.0 136.5 136.5 136.5 111.1 Inches 1.875 2.875 2.875 3.625 3.625 3.625 3.625 2.875 5.375 5.375 5.375 4.375 mm 51 51 51 51 51 51 51 51 76 76 76 76 Inches 2 2 2 2 2 2 2 2 3 3 3 3 TRAVEL S17400 (17-4 Stainless Steel) with H1075 Heat Treatment 32B6057X012 42B8244X012 42B8245X012 32B9324X012 32B9325X012 32B9326X012 32B9327X012 32B9328X012 43B0082X012 43B0083X012 43B0084X012 33B0085X012 S17400 Stainless Steel with H1150 Heat Treatment For Sour Gas Service 32B6057X032 42B8244X032 42B8245X032 32B9324X022 32B9325X022 32B9326X022 32B9327X022 32B9328X022 43B0082X022 43B0083X022 43B0084X022 33B0085X022

F22 Ion Nitride

32B6057X022 42B8244X022 42B8245X022 32B9324X032 32B9325X032 32B9326X032 32B9327X032 32B9328X032 43B0082X032 43B0083X032 43B0084X032 33B0085X032

Class 1500

6
1. Cage and baffle assembly.

Key 2* Cage Assembly for Design HPS, HPAS(1), HPT, or HPAT(1) Valves with Cavitrol III Trim MATERIAL VALVE RATING VALVE SIZE, INCHES 1 2 Class 1500 3 4 6
1. 1- and 2-inch only.

CAGE ASSEMBLY DESCRIPTION Full 2-stage Full 2-stage Full 3-stage Full 2-stage Full 3-stage Full 2-stage Full 3-stage Full 2-stage Full 3-stage

PORT DIAMETER mm 22.2 44.5 25.4 63.5 47.6 87.3 73 133.4 115.8 Inches 0.875 1.75 1 2.5 1.875 3.4375 2.875 5.25 4.5625

TRAVEL mm 38 51 51 64 64 76 76 102 102 Inches 1.5 2 2 2.5 2.5 3 3 4 4

S17400 (17-4 Stainless Steel) w/H1075 Heat Treatment 32B8266X022 33B0160X012 32B6070X012 32B8522X012 32B8255X012 32B9331X012 32B9334X012 33B0088X012 33B0091X012

S17400 w/H1150 Heat Treatment for Sour Gas Service 32B8266X012 33B0160X022 32B6070X022 32B8522X022 32B8255X022 32B9331X022 32B9334X022 33B0088X022 33B0091X022

*Recommended spare parts

31

Instruction Manual

HP and HPA Valves


C-seal Parts for Design HPD Valve (Keys 2*, 5*, 4*, 64*, 8*, and 6*)
VALVE PORT TRAVEL SIZE DIA TRIM STEM DIAMETER

Form 5299 April 2004

Inch

Inch

Inch
201B 202

mm
19.1 19.1 19.1 25.4 19.1 19.1

Inch
0.75 0.75 0.75 1 0.75 0.75 1 1 0.75 1 1 1 1 1.25 1.25

CHARACTERISTIC
Linear Equal % Linear Equal %

CAGE

PLUG/ RETAINER

SEAT RING

C-seal

PISTON RING (2 reqd)

STEM

Key 2
44B9820X012 47B1674X012 --44B7068X012

Key 5

Key 4

Key 64

Key 8

Key 6

27B1676X012 22B6095X012 24B3621X012 14B3620X012 1U3416X0042 24B7070X012 22B6095X012 24B3621X012 14B3620X012 1U3416X0042 24B7070X012 22B6095X012 24B3621X012 14B3620X012 1U3416X0042 24B9822X012 22B6095X012 24B3621X012 14B3620X012 1K7447X0042 37B2274X012 22B9339X012 23B9198X012 14B5340X012 10A9265XV62 34B5342X022 22B9339X012 23B9198X012 14B5340X012 10A9265XV62 34B5342X012 22B9339X012 23B9198X012 14B5340X012 11A3429XG52

2.875

2 208 210 201B

Whisper III-A1 47B2276X012 Whisper III-B1 48B0643X012 Linear Equal % Linear Equal % Linear Equal % Linear Equal % 44B9820X012 47B1674X012 --47B1672X012 44B3622X012 --44B3622X012 ---

3.625

202 25.4 203 208 202 207 25.4 19.1 25.4 25.4 25.4 25.4 31.8 31.8

Whisper III-A1 34B9836X012 34B9837X012 22B9339X012 23B9198X012 14B5340X012 11A3429XG52 Whisper III-C3 34B5343X012 34B5342X022 22B9339X012 23B9198X012 14B5340X012 10A9265XV62 Whisper III-A1 37B0194X012 34B5342X012 22B9339X012 23B9198X012 14B5340X012 11A3429XG52 Equal % 43B9204X012 34B3619X012 23B0094X012 11A3429XG52 24B2191X012 13B9186X012 10A6073X072 Whisper III-B3 47B3201X012 37B3203X012 23B0093X012 Whisper III-A1 47B3208X012 34B3619X012 Linear 47B8742X012 37B8744X012 23B0094X012 Whisper III-A1 47B3208X012 34B3619X022

5.375

208 201B 208

32

*Recommended spare parts

Instruction Manual
Form 5299 April 2004

HP and HPA Valves


TRIM DIAMETER Inch mm Inch 2 810A 816 810A 816 810A 816 810A 19.1 12.7 19.1 19.1 25.4 0.75 0.5 0.75 0.75 1
TVL STEM

TSO Parts for Design HPS and HPT Valves (Keys 2*, 4*, and 5*)
VALVE PORT SIZE DIA

Inch 2-In HPS 3-In HPT

Inch 0.8125

ACTUATOR GROUP 1 400 1 1 100 & 101 401, 403 402 401, 403 402 404 405, 406 407 404 405, 406 407 1

CHARACTERISTIC Cavitrol III 3-Stage Cavitrol III 3-Stage

CAGE

SEAT RING

PLUG/ STEM ASSY

Key 2 32B6070X012 32B6070X012 32B8255X012 32B8255X022 32B8255X012 32B8255X022 32B9334X012

Key 4 37B9555X012 38B1877X012 27B6587X012 27B6588X012 27B6587X012 27B6588X012 27B6596X012 27B6597X012 27B6596X012 27B6597X012 38B2652X012 38B2653X012 38B2652X012

Key 5 27B9559X022 27B9559X032 27B3115X022 27B3115X032 27B3115X042 27B3115X052 27B6604X012 27B6604X022 27B6604X032 27B6604X042 38B2647X012 38B2647X022 38B2647X052 38B2647X062 38B2654X012 38B2654X022 38B2654X032 38B2654X072 38B2654X082 38B2654X092 38B2274X012 38B2274X032 38B2275X012

1.6875

2.5

4-In HPT

2.6875

816 810A 816 810A

Cavitrol III 3-Stage

32B9334X022 32B9334X012 32B9334X022 33B0091X012 33B0091X022

19.1 816 6-In HPT 4.375 4 810A 25.4 816 812 2.5 & 3 818 2.5 3 5.1875 3 2.5 3 3 818 25.4 812 25.4 19.1

0.75

Cavitrol III 3-Stage

33B0091X012

33B0091X022 Linear Equal % Linear Equal % Linear Equal % Linear Mod Equal % Linear Mod Equal % Linear Equal % Linear Mod Equal % Linear Mod Equal % 43B0079X012 43B0261X012 43B0079X032 43B0261X032 43B0079X012 43B0261X012 43B0079X012 43B0261X012 43B0079X012 43B0261X012 43B0079X032 43B0261X032 43B0079X032 43B0261X032 43B0079X032 43B0261X032

38B2653X012 38B2283X012 38B2284X012

0.75 1 100 1 100 101 100 1 100 101

6-In HPT

38B2283X012

38B2275X022 38B2275X022 38B2275X052

38B2284X012

38B2275X062 38B2275X062

*Recommended spare parts

33

Instruction Manual

HP and HPA Valves


TSO Parts for Design HPS and HPT Valves (Keys 8*, 63*, 9*, and 10*)
VALVE PORT SIZE DIA TVL STEM

Form 5299 April 2004

Inch 2-In HPS 3-In HPT

Inch 0.8125

TRIM DIAMETER Inch mm Inch 2 810A 816 810A 816 810A 816 810A 19.1 12.7 19.1 19.1 25.4 0.75 0.5 0.75 0.75 1

ACTUATOR GROUP 1 400 1 1 100 & 101 401, 403 402 401, 403 402 404 405, 406 407 404 405, 406 407 1

CHARACTERISTIC Cavitrol III 3-Stage Cavitrol III 3-Stage

SEAL RING

ANTI-EXT RING

BACKUP RING

RETAINING RING

Key 8 -----

Key 63 -----

Key 9 ----10A4218X022 10A4218X012 10A4218X022 10A4218X012 10A4217X012

Key 10 ----10A4220X012 10A4220X082 10A4220X012 10A4220X082 10A4219X012 10A4219X052 10A4219X012 10A4219X052 17A4415X042 17A4415X032 17A4415X042

1.6875

2.5

10A4216X102

22B4694X012

4-In HPT

2.6875

816 810A 816 810A

Cavitrol III 3-Stage

10A4215X102

22B2617X012

10A4217X022 10A4217X012 10A4217X022

17A4413X042 17A4413X042 Cavitrol III 3-Stage 17A4413X042

21B2141X012 21B2141X012 21B2141X012

17A4414X012 17A4414X022 17A4414X012

19.1 816 6-In HPT 4.375 4 810A 25.4 816 812 2.5 & 3 818 2.5 3 5.1875 3 2.5 3 3 818 25.4 812 25.4 19.1

0.75

17A4413X042 Linear Equal % Linear Equal % Linear Equal % Linear Mod Equal % Linear Mod Equal % Linear Equal % Linear Mod Equal % Linear Mod Equal % 10A5411X102 10A5411X102

21B2141X012 21B9342X012 21B9342X012

17A4414X022 10A5409X012 10A5409X022

17A4415X032 10A5410X012 10A5410X052

0.75 1 100 1 100 101 100 1 100 101

6-In HPT

10A5411X102

21B9342X012

10A5409X012

10A5410X012

10A5411X102

21B9342X012

10A5409X022

10A5410X052

34

*Recommended spare parts

Instruction Manual
Form 5299 April 2004

HP and HPA Valves


PORT DIAMETER mm 6.4 9.5 Micro-Form, Micro-Flute 12.7 19.1 25.4 HPAS 19.1 6.4 9.5 12.7 Micro-Form and Micro-Flute 19.1 25.4 31.8 38.1 19.1 HPAS 25.4 31.8 38.1 HPD, HPT, HPS 47.6 73.0 92.1 Inches 0.25 0.375 0.5 0.75 1 0.75 0.25 0.375 0.5 0.75 1 1.25 1.5 0.75 1 1.25 1.5 1.875 2.875 3.625 S41600 (416 SST) 22B6020X012 22B6021X012 22B6022X012 22B6023X012 22B6019X012 23B6626X012 23B0170X012 22B4186X012 23B0172X012 23B0174X012 23B0176X012 22B6000X012 22B6002X012 23B6652X012 23B6629X012 23B6658X012 22B4235X012 22B6004X012 22B6094X012 22B9338X012 SEAT RING MATERIAL S31600 (316 SST) CoCr-A Seat ------22B6064X012 22B6065X012 23B6627X012 23B0171X012 22B4208X012 23B0173X012 23B0175X012 23B0177X012 22B6001X012 22B6003X012 23B6653X012 22B4241X012 22B4242X012 22B4243X012 22B6005X012 22B6095X012 22B9339X012 S31600 CoCr-A Seat & Bore 22B6061X012 22B6062X012 22B6063X012 -----------------------------------

Key 4* Seat Ring for Constructions without Cavitrol III Cage VALVE SIZE, INCHES

DESIGN

All HPD and HPT Whisper III Level A1, A3, B3, C3 HPD and HPT Whisper III Level D3 HPD and HPT Whisper III Level A1, B3, C3 HPD and HPT Whisper III Level D3

73.0

2.875

22B9340X012

22B9341X012

---

136.5

5.375

23B0093X012

23B0094X012

---

111.1

4.375

23B0095X012

23B0096X012

---

Key 4* Seat Ring for Valve with Cavitrol III Trim VALVE RATING, CLASS VALVE SIZE, INCHES 1 2 1500 3 4 6 2-STAGE S44004 (440C SST) with Heat Treatment 22B8353X012 23B0163X012 22B6096X012 22B9342X012 23B0097X012 S31600 (316 SST) CoCr-A 22B8354X012 23B0164X012 22B6097X012 22B9343X012 23B0098X012 3-STAGE S44004 with Heat Treatment --22B6068X012 22B6098X012 22B9344X012 23B0099X012 S31600 CoCr-A --22B6069X012 22B6099X012 22B9345X012 23B0100X012

*Recommended spare parts

35

Instruction Manual

HP and HPA Valves


Key 4* Seat and Liner for Buttweld End and Socket Weld End Angle Valves VALVE RATING, CLASS VALVE SIZE, INCHES DESIGN PORT DIAMETER mm Inches 6.4 1 Micro-Flute 9.5 12.7 6.4 Micro-Flute 1500 2 HPAS 9.5 12.7 19.1 25.4 31.8 38.1 HPAD, HPAT Key 4* Seat and Liner for ANSI and DIN Flanged Angle Valves VALVE RATING, CLASS VALVE SIZE, INCHES DESIGN PORT DIAMETER mm Inches 6.4 1 Micro-Flute 9.5 12.7 6.4 Micro-Flute 1500 2 HPAS 9.5 12.7 19.1 25.4 31.8 38.1 HPAD, HPAT 47.6 0.25 0.375 0.5 0.25 0.375 0.5 0.75 1 1.25 1.5 1.875 47.6 0.25 0.375 0.5 0.25 0.375 0.5 0.75 1 1.25 1.5 1.875

Form 5299 April 2004

SEAT AND LINER MATERIAL S44004 (440C SST) R30006 (Alloy 6) 23B6623X012 23B6625X012 23B6624X012 23B6650X012 23B7141X012 23B6651X012 23B6647X012 23B7143X012 23B7145X012 23B7147X012 23B6645X012 23B6623X022 23B6625X022 23B6624X022 23B6650X022 23B7141X022 23B6651X022 23B6647X022 23B7143X022 23B7145X022 23B7147X022 23B6645X022

SEAT AND LINER MATERIAL S44004 (440C SST) R30006 (Alloy 6) 23B6620X012 23B6622X012 23B6621X012 23B6648X012 23B7140X012 23B6649X012 23B6646X012 23B7142X012 23B7144X012 23B7146X012 23B6644X012 23B6620X022 23B6622X022 23B6621X022 23B6648X022 23B7140X022 23B6649X022 23B6646X022 23B7142X022 23B7144X022 23B7146X022 23B6644X022

36

*Recommended spare parts

Instruction Manual
Form 5299 April 2004

HP and HPA Valves


MATERIAL

Key 5* Valve Plug for Design HPS and HPAS Valves with Micro-Form Plug
VALVE STEM CONNECTION PORT DIAMETER Trim 201A S41600 (416 Stainless Steel) Size 1 Trim 202, 203, 204, 210 Size 2 Trim 202 S31600 (316 Stainless Steel) CoCr-A Seat, Guide, and Contour 16A5404X012 19A6765X032 16A5405X012 16A5406X012 16A5408X012 16A5407X012 16A5409X012 23B0165X012 11B7697X012 18A4133X012 23B0167X012 28A1638X052 26A5410X052 19A7924X032 10B8013X012 28A1640X132 26A5411X122 12B0079X012 28A1642X062 26A5412X072

VALVE SIZE, INCHES

mm

Inches

mm 6.4 9.5 12.7 19.1 25.4 19.1 25.4 6.4 12.7 19.1 25.4 31.8 38.1 19.1 25.4 31.8 38.1 25.4 31.8 38.1

Inches 0.25 0.375 0.5 0.75 1 0.75 1 0.25 0.5 0.75 1 1.25 1.5 0.75 1 1.25 1.5 1 1.25 1.5

Size 2 Trim 203, 204, 210 S31600 (316 Stainless Steel) CoCr-A Seat, Guide, and Contour --------------23B0165X022 11B7697X042 18A4133X022 23B0167X022 28A1638X012 26A5410X012 19A7924X052 10B8013X042 28A1640X012 26A5411X012 12B0079X022 28A1642X012 26A5412X012

12.7 1 19.1

0.5

0.75

12.7

0.5

2 19.1 0.75

16A5327X012 12B2696X052 16A5328X012 16A5329X012 16A5331X012 16A5330X012 16A5332X012 23B0188X012 10B3297X012 19A5980X042 23B0166X012 18A1637X012 16A5402X012 23B0168X012 18A4222X012 18A1639X012 16A5333X012 23B0169X012 18A1641X012 16A5334X012

25.4

Key 5* Valve Plug for 1-Inch Design HPS and HPAS Valves with Micro-Flute Plug (Flow-Up Only) PORT DIAMETER mm 1 Flute 2 Flutes 3 Flutes 3 Flutes 3 Flutes 6.4 6.4 6.4 9.5 12.7 Inches 0.25 0.25 0.25 0.375 0.5 MATERIAL Trim 201A S44004 (440C Stainless Steel) with Heat Treatment 18A1643X012 18A1644X012 18A1645X012 18A1647X012 18A1649X012 Trim 202, 203, 204 S31600 (316 Stainless Steel) with Alloy 6 (CoCr-A) Seat, Guide, and Tip 17A8607X052 18A1646X012 17A8608X052 18A1648X012 18A1650X012

VALVE RATING

PLUG STYLE

Class 1500

Key 5* Valve Plug for Design HPAS Valves with Micro-Flute Plug (Flow-Down Only) MATERIAL VALVE RATING VALVE SIZE, INCHES PORT DIAMETER PLUG STYLE mm 6.4 9.5 12.7 12.7 6.4 9.5 12.7 12.7 Inches 0.25 0.375 0.5 0.5 0.25 0.375 0.5 0.5 Trim 201A S44004 (440C Stainless Steel) with Heat Treatment 18A1643X012 21B4245X012 21B4246X012 21B4244X012 21B4247X012 21B4251X012 21B4252X012 22B5881X012 Size 1 Trim 202, 203, 204 Size 2 Trim 202 S31600 (316 Stainless Steel) with Alloy 6 (CoCr-A) Seat, Guide, and Tip 17A8607X052 21B4240X012 21B4243X012 21B4230X012 21B4254X012 21B4255X012 21B4259X012 22B5882X012

Size 2 Trim 203, 204

1 1500 2

1 Flute 2 Flute 1 Flute 2 Flute

--------21B4254X022 21B4255X022 21B4259X022 22B5882X022

*Recommended spare parts

37

Instruction Manual

HP and HPA Valves


Key 5* Valve Plug for Cavitrol III Trim VALVE PORT STEM CAGE ACTUATOR CONNECTION DIAMETER S44004 (440C ASSEMBLY GROUP Stainless Steel) DESCRIPTION w/ Heat Treatment mm Inches mm Inches w/ S20910 Stem 2-stage 2-stage 3-stage 1 1 1 1 1 400 3 HPT 2-stage 1 100 101 400 3 HPT 3-stage 1 100 101 2-stage 4 HPT 3-stage 1 100, 101 1 100, 101 401, 403 402 404 2-stage 405, 406 407 404 405, 406 6 HPT 407 401, 403 402 404 3-stage 405, 406 407 404 405, 406 407 12.7 19.1 12.7 19.1 19.1 12.7 19.1 25.4 25.4 12.7 19.1 25.4 25.4 19.1 25.4 19.1 25.4 19.1 19.1 25.4 25.4 25.4 31.8 31.8 31.8 19.1 19.1 25.4 25.4 25.4 31.8 31.8 31.8 0.5 0.75 0.5 0.75 0.75 0.5 0.75 1 1 0.5 0.75 1 1 0.75 1 0.75 1 0.75 0.75 1 1 1 1.25 1.25 1.25 0.75 0.75 1 1 1 1.25 1.25 1.25 22.2 22.2 44.5 44.5 25.1 63.5 63.5 63.5 63.5 47.6 47.6 47.6 47.6 87.3 87.3 73 73 133.4 133.4 133.4 133.4 133.4 133.4 133.4 133.4 0.875 0.875 1.75 1.75 1 2.5 2.5 2.5 2.5 1.875 1.875 1.875 1.875 3.4375 3.4375 2.875 2.875 5.25 5.25 5.25 5.25 5.25 5.25 5.25 5.25 22B8351X022 22B8351X032 37A2294X052 37A2294X062 22B6074X012 37A4303X052 37A4304X052 37A4304X052 37A4305X062 37A4320X052 37A4321X112 37A4321X132 37A4321X142 24A5259X092 24A5260X072 38A0014X062 38A0015X032 37A4390X042 37A4390X052 37A4391X072 37A4391X082 37A4391X092 37A4392X052 37A4392X062 37A4392X072 37A4407X042 37A4407X052 37A4408X062 37A4408X072 37A4408X082 37A4409X052 37A4409X062 37A4409X072 MATERIAL S31600 (316 Stainless Steel) w/ CoCr-A Seat and Guide w/ S20910 Stem 22B8352X022 22B8352X032 37A2295X102 37A2295X112 22B6075X012 37A4306X032 37A4307X042 37A4308X052 37A4308X062 37A4322X042 37A4323X102 37A4323X112 37A4323X122 24A5280X052 24A5281X092 38A0016X062 38A0017X032 37A4393X042 37A4393X052 37A4394X052 37A4394X062 37A4394X072 37A4395X052 37A4395X062 37A4395X072 37A4410X042 37A4410X052 37A4411X052 37A4411X062 37A4411X072 37A4412X052 37A4412X062 37A4412X072

Form 5299 April 2004

VALVE SIZE

VALVE DESIGN

S31600 w/ CoCr-A Seat and Guide w/ S31600 Stem 22B8351X042 22B8351X052 37A2294X072 37A2294X082 22B6074X032 37A4303X062 37A4304X062 37A4305X012 37A4305X032 37A4320X062 37A4321X122 37A4321X032 37A4321X042 24A5259X062 24A5260X062 38A0014X022 38A0015X022 37A4390X022 37A4390X032 37A4391X022 37A4391X032 37A4391X042 37A4392X022 37A4392X032 37A4392X042 37A4407X022 37A4407X032 37A4408X092 37A4408X032 37A4408X102 37A4409X022 37A4409X082 37A4409X042

HPS, HPAS HPT, HPAT HPS, HPAS

115.8 4.5625 115.8 4.5625 115.8 4.5625 115.8 4.5625 115.8 4.5625 115.8 4.5625 115.8 4.5625 115.8 4.5625

38

*Recommended spare parts

Instruction Manual
Form 5299 April 2004

HP and HPA Valves

Key 5* Valve Plug for a 2 to 6-Inch Class 1500 Globe Valve Without Micro-Form, Micro-Flute, or Cavitrol III Trim Also for Use with a 2 to 3-Inch Globe Valve with a Whisper Trim III Cage
MATERIAL VALVE SIZE, INCHES VALVE STEM CONNECTION PORT DIAMETER Trim 201 and 207 Size 2 and 3 Trim 201 Size 4 and 6 S41600 (416 Stainless Steel) 32B6006X012 32B6008X012 32B6010X012 32B6012X012 16A5344X012 16A5345X012 16A5346X012 32B8246X012 32B8248X012 32B8250X012 36A5350X012 36A5351X012 36A5352X012 16A5354X012 16A5355X012 32B9346X012 32B9348X012 36A5358X012 36A5359X012 36A5362X012 36A5363X012 36A5364X012 39A6740X012 36A5365X012 36A5366X012 36A5367X012 30B2224X012 Trim 202 and 208 Size 2 and 3 Trim 202 Size 4 and 6 S31600 (316 Stainless Steel) CoCr-A Seat/Guide 32B6007X022 32B6008X022 ----36A5423X062 36A5424X082 36A5425X042 32B8247X032 32B8249X032 32B8251X032 ------36A5433X042 36A5434X062 32B9347X022 32B9349X022 ----36A5441X092(1) 36A5441X132(2) 36A5442X102(1) 36A5442X112(2) 36A5443X082(1) 36A5443X092(2) 38A6943X072(1) 38A6943X082(2) --------Trim 204 and 209, 210 Size 2 and 3 Trim 204, 210 Size 4 and 6 S31600 32B6007X012 32B6008X012 32B6011X012 32B6013X012 36A5423X012 36A5424X012 36A5425X012 32B8247X022 32B8249X022 32B8251X022 36A5429X012 36A5430X012 36A5431X012 36A5433X012 36A5434X012 32B9347X032 32B9349X032 36A5437X132 36A5438X092 36A5441X092 36A5442X102 36A5443X082 38A6943X072 36A5444X012 36A5445X012 36A5446X012 38A8300X012

VALVE DESIGN

mm 12.7 19.1 12.7 19.1 12.7 19.1 25.4 12.7 19.1 25.4 12.7 19.1 25.4 19.1 25.4 19.1 25.4 19.1 25.4 19.1 25.4 HPD 31.8 6 50.8 19.1 25.4 31.8 50.8

Inches 0.5 0.75 0.5 0.75 0.5 0.75 1 0.5 0.75 1 0.5 0.75 1 0.75 1 0.75 1 0.75 1 0.75 1 1.25 2 0.75 1 1.25 2

mm 47.6 47.6 47.6 47.6 47.6 47.6 47.6 73 73 73 73 73 73 73 73 92.1 92.1 92.1 92.1 136.5 136.5 136.5 136.5 136.5 136.5 136.5 136.5

Inches 1.875 1.875 1.875 1.875 1.875 1.875 1.875 2.875 2.875 2.875 2.875 2.875 2.875 2.875 2.875 3.625 3.625 3.625 3.625 5.375 5.375 5.375 5.375 5.375 5.375 5.375 5.375

Trim 203 S31600 CoCr-A Seat/Guide 32B6007X012 32B6008X012 32B6011X012 32B6013X012 36A5423X012 36A5424X012 36A5425X012 32B8247X012 32B8249X012 32B8251X012 36A5429X012 36A5430X012 36A5431X012 36A5433X012 36A5434X012 32B9347X012 32B9349X012 36A5437X092 36A5438X062 36A5441X052 36A5442X042 36A5443X042 38A6943X042 36A5444X012 36A5445X012 36A5446X012 38A8300X012

HPD 2 HPT HPS

HPD 3

HPT HPS HPD

4 HPT

HPT

1. For -20_ to 650_F (-29_ to 343_) temperature range (Trim 202). 2. For 500_ to 1050_F (260_ to 566_C) temperature range (Trim 202H).

Key 5* Valve Plug for a 2-Inch Class 1500 Angle Valve Without Micro-Form, Micro-Flute, Micro-Flat, or Cavitrol III Trim Also for Use with a 2-Inch Angle Valve with a Whisper Trim III Cage MATERIAL VALVE SIZE, INCHES VALVE STEM CONNECTION VALVE DESIGN mm 12.7 19.1 12.7 19.1 12.7 19.1 25.4 Inches 0.5 0.75 0.5 0.75 0.5 0.75 1 mm 47.6 47.6 47.6 47.6 47.6 47.6 47.6 Inches 1.875 1.875 1.875 1.875 1.875 1.875 1.875 PORT DIAMETER Trim 201 Size 1 and 2 Trim 207 Size 2 Whisper III S41600 (416 SST) 32B6006X012 32B6008X012 32B6010X012 32B6012X012 16A5344X012 16A5345X012 16A5346X012 Trim 202 Size 1 and 2 Trim 208 Size 2 Whisper III S31600 (316 SST) CoCr-A Seat/Guide 32B6007X022 32B6008X022 ----36A5423X062 36A5424X082 36A5425X042 Trim 204 Size 1 and 2 Trim 209 Size 2 Whisper III S31600 CoCr-A Seat/Guide 32B6007X012 32B6008X012 32B6011X012 32B6013X012 36A5423X012 36A5424X012 36A5425X012

Trim 203 S31600 CoCr-A Seat/Guide 32B6007X012 32B6008X012 32B6011X012 32B6013X012 36A5423X012 36A5424X012 36A5425X012

HPAD 2 HPAT HPAS

*Recommended spare parts

39

Instruction Manual

HP and HPA Valves


Key 5* Valve Plug for a 1- to 2-Inch Class 1500 Angle Valve without Micro-Form, Micro-Flute, Micro-Flat, or Cavitrol III Trim With Restricted Port Equal Percentage Cage, Flow Down Only VALVE SIZE, INCHES 1 VALVE STEM CONNECTION mm HPAS 19.1 19.1 2 HPAS 19.1 25.4 25.4 Inches 0.75 0.75 0.75 1 1 PORT DIAMETER mm 19.1 19.1 25.4 31.8 38.1 Inches 0.75 0.75 1 1.25 1.5 MATERIAL Trim 201 S41600 (416 SST) 13B6632X012 13B6660X012 23B6630X012 23B6659X012 22B4236X012 Trim 202 S31600 (316 SST) CoCr-A Seat/Guide 13B6633X012 13B6661X012 21B2095X012 21B2098X022 21B2099X022 Trim 203 S31600 CoCr-A Seat/Guide 13B6633X012 13B6661X012 21B2095X012 21B2098X012 21B2099X012

Form 5299 April 2004

VALVE DESIGN

Trim 204 S31600 CoCr-A Seat/Guide 13B6633X012 13B6661X012 21B2095X012 21B2098X022 21B2099X022

Key 5* Valve Plug for 4- and 6-Inch Valves with Whisper III Trim MATERIAL VALVE SIZE, INCHES VALVE STEM CONNECTION VALVE DESIGN mm 19.1 25.4 19.1 25.4 19.1 25.4 19.1 25.4 25.4 31.8 HPD 25.4 6 31.8 25.4 31.8 25.4 31.8 1.25 1 1.25 1 1.25 111.1 136.5 136.5 111.1 111.1 4.375 5.375 5.375 4.375 4.375 39A9102X022 36A5366X072 36A5367X062 39A9101X022 39A9103X022 1 111.1 4.375 39A9100X022 Inches 0.75 1 0.75 1 0.75 1 0.75 1 1 1.25 mm 92.1 92.1 73 73 92.1 92.1 73 73 136.5 136.5 Inches 3.625 3.625 2.875 2.875 3.625 3.625 2.875 2.875 5.375 5.375 PORT DIAMETER Trim 207 Size 4 and 6 S41600 (416 Stainless Steel) 32B9346X012 32B9348X012 32B8248X012 32B8250X012 36A5358X012 36A5359X012 36A5351X012 36A5352X012 36A5363X092 36A5364X052 Trim 208 Size 4 and 6 S31600 (316 Stainless Steel) CoCr-A Seat/Guide 32B9347X022 32B9349X022 32B8249X032 32B8251X032 --------36A5442X112(1) 36A5442X122(2) 36A5443X092(1) 36A5443X102(2) 39A9104X152(1) 39A9104X162(2) 39A9106X152(1) 39A9106X162(2) --------Trim 209 Size 4 and 6 S31600 CoCr-A Seat/Guide 32B9347X032 32B9349X032 32B8249X022 32B8251X022 36A5437X132 36A5438X092 36A5430X012 36A5431X012 36A5442X112 36A5443X092 39A9104X152 39A9106X152 36A5445X062 36A5446X032 39A9105X072 39A9107X072

HPD 4 HPT

HPT

1. For 29 to 343_C (20 to 650_F) temperature range (Trim 208). 2. For 260 to 566_C (500 to 1050_F) temperature range (Trim 208H).

Key 5* Valve Plug for Design HPAS Valves with Micro-Flat Plug/Seat Ring VALVE STEM CONNECTION PORT DIAMETER MATERIAL Trim 201A S44004 (440C Stainless Steel) 23B0645X012 23B0647X012 23B0649X012 32B4237X012 Trim 202, 203, 204 S31600 (316 Stainless Steel) CoCr-A Seat, Guide, and Contour 23B0646X012 23B0648X012 23B0650X012 32B4239X012

VALVE RATING

VALVE SIZE, INCHES

mm 12.7 19.1 2 19.1

Inches 0.5 0.75 0.75

mm 9.5 12.7 19.1 25.4

Inches 0.375 0.5 0.75 1

Class 1500

40

*Recommended spare parts

Instruction Manual
Form 5299 April 2004

HP and HPA Valves


PORT DIAMETER PORT DIAMETER mm Inches MATERIAL Trim 202, 203, 204 S31600 (316 Stainless Steel) CoCr-A Seat, Guide, and Contour 23B0646X022 23B0648X022 32B4239X022 23B0646X032 23B0648X032 32B4239X032

Key 5* Valve Plug for Design HPAS Valves with Micro-Flat Plug/Seat and Liner

VALVE RATING

VALVE SIZE, INCHES

VALVE STEM CONNECTION

mm

Inches

Trim 201 S44004 (440C Stainless Steel)

For ANSI and DIN Flanged Valves Class 1500 1 2 12.7 19.1 0.5 0.75 9.5 12.7 25.4 9.5 12.7 25.4 0.375 0.5 1 0.375 0.5 1 23B0645X022 23B0647X022 32B4237X022 23B0645X032 23B0647X032 32B4237X032

For Butt Weld and Socket Weld Valves Class 1500 1 2 12.7 19.1 0.5 0.75

Key 6* Valve Plug Stem for Class 1500 Standard and Whisper Valves with Whisper Trim III Cage
VALVE STEM CONNECTION mm Inches mm VALVE STEM TRAVEL Inches Micro-Form or MicroFlute with 6.4 mm (0.25 inch) port MATERIAL DESCRIPTION S20910(1) S20910(1) S31600(2) (Nitronic 50) (for (For Standard (For Standard Extension Style Bonnet) Bonnet) 1 Bonnet) 1N8210X0092 10A8840XAA2 S31600(2) (For Extension Bonnet)

VALVE ACTUATOR SIZE, GROUP INCHES

19.1

0.75

1N821035162 10A8840X512

12.7 1 1

0.5

19.1

0.75

Micro-Flute or Micro-Flat with 9.5 or 12.7 mm 1N8210X0092 (0.375 or 0.5 inch) port Micro-Form with 12.7, 19.1 or 25.4 mm (0.5, 0.75, or 1-inch) port 10A8840XT82

10A8840XAA2

1N821035162 10A8840X512

19.1, 29

0.75, 1.125

1P6694X0092

10A8840XB42 1P669435162

19.1, 29 19.1 0.75 19.1, 29

0.75, 1.125 0.75, 1.125

Micro-Form with 19.1 or 25.4 mm (0.75 or 1-inch) 1K5878X0092 port HPAS with 19.1 mm (0.75 inch) port Micro-Form, Micro-Flute HPD, HPAD, HPT, HPAT, HPS, HPAS 16A4704X472

1L3841X0032 16A4704X522

1K5878X0012 1L384135162 16A4704X322 16A4704X532

12.7

0.5

19.1, 29, 38 0.75, 1.125, 1.5

1N8210X0092

23B0035X052

1N821035162 23B0035X062

1 19.1 0.75

19.1, 29, 38 0.75, 1.125, 1.5

Micro-Form, Micro-Flat 1P6696X0032 HPD, HPAD, HPT, HPAT HPAS with 16A4704X462 19.1 mm (0.75 inch) port HPAS with 25.4 mm (1-inch) port - Continued 16A4704X472

1P6697X0142 16A4704X482 16A4704X502

1P6696X0012 1P669735162 16A4704X042 16A4704X492 16A4704X322 16A4704X512

19.1, 29

0.75, 1.125

*Recommended spare parts

41

Instruction Manual

HP and HPA Valves


Key 6* Valve Plug Stem for Class 1500 Standard and Whisper Valves with Whisper Trim III Cage (Continued)
VALVE STEM CONNECTION mm Inches mm VALVE STEM TRAVEL Inches Micro-Form with 25.4 mm (1-inch) port 19 0.75 MATERIAL DESCRIPTION

Form 5299 April 2004

VALVE ACTUATOR SIZE, GROUP INCHES

S20910(1) S20910(1) S31600(2) (Nitronic 50) (for (For Standard (For Standard Extension Style Bonnet) Bonnet) 1 Bonnet) 10A3282X222 11A3429XN82 11A3429XN82 13A9206X362 1L1990X0022 1L1990X0022 1L1990X0022 13A9206X382 11A3429XN92

S31600(2) (For Extension Bonnet)

10A3282X012 11A3429X152 10A3282X012 11A3429X152 13A9206X312 13A9206X372 11A3429X232 1L199035162 11A3429X232 1L199035162 11A3429X232 1L199035162 13A9206X332 13A9206X392 1K778335162 11A3429X922

Micro-Form with 10A3282X222 31.8 mm (1.25 inch) port HPAS with 31.8 mm (1.25 inch) port Micro-Form with 25.4 mm (1-inch) port 13A9206X302 11A3429XG52

Micro-Form with 11A3429XG52 31.8 mm (1.25 inch) port Micro-Form with 38.1 mm (1.5 inch) port 100 2 25.4 1 29 1.125 HPAS with 31.8 mm (1.25 inch) port HPS, HPAS with 47.6 mm (1.875 inch) port HPS, HPAS with 47.6 mm (1.875 inch) port Micro-Form with 38.1 mm (1.5 inch) port 38 1.5 HPS, HPAS with 47.6 mm (1.875 inch) port 11A3429XG52 13A9206X322 1K7783X0032

11A3429XG52 1L2687X0152 1L2687X0152

1L1990X0022 11A3429XL32 11A3429XL32

11A3429X232 1L199035162 1L2687X0012 11A3429X452 1L2687X0012 11A3429X452

101

25.4

19, 29, 38

0.75, 1.125, 1.5

Micro-Form, HPS, HPAS with 38.1 mm (1.5) & 1K7447X0042 47.6 mm (1.875) port HPAS with 31.8 mm (1.25 inch) port HPD with 73 mm (2.875 inch) port HPT with 73 mm (2.875 inch) port HPD with 73 mm (2.875 inch) port 13A9206X342 1U2179X0072 1U4369X0072 10A9265XV62 1P6696X0032 10A9265XV72 1K7783X0032 1L2687X0152 1N3256X0052 1L2687X0152 1K9289X0102 1N6682X0072 1L1446X0052 1K7447X0042 1L2687X0152

1L9086X0032 13A2906X402 -----------------------------

1K744735162 1L9086X00A2 13A9206X352 13A9206X412 1U217935162 1U4369X0012 10A9265X122 1P6696X0012 10A9265X202 1K778335162 1L2687X0012 1N325635162 1L2687X0012 1K928935162 1N6682X0032 1L144635162 1K744735162 1L2687X0012 -----------------------------

12.7

0.5

38, 50.8

1.5, 2

1 19.1 0.75 38, 50.8 1.5, 2

HPT with 73 mm (2.875 inch) port HPS with 73 mm (2.875 inch) port HPD

3 38 100 25.4 1 50.8 2 1.5

HPT HPS HPD HPT HPS HPD

101

25.4

38, 50.8

1.5, 2

HPT HPS - Continued -

42

*Recommended spare parts

Instruction Manual
Form 5299 April 2004

HP and HPA Valves


VALVE STEM CONNECTION mm Inches mm VALVE STEM TRAVEL Inches HPD with 92.1 mm (3.625 inch) port(3) HPD with 73 mm (2.875 inch) port(4) HPT with 92.1 mm (3.625 inch) port(3) HPT with 73 mm (2.875 inch) port(4) HPD with 92.1 mm (3.625 inch) port(3) HPD with 73 mm (2.875 inch) port(4) HPT with 92.1 mm (3.625 inch) port(3) HPT with 73 mm (2.875 inch) port(4) HPD with 92.1 mm (3.625 inch) port(3) HPD with 73 mm (2.875 inch) port(4) HPT with 92.1 mm (3.625 inch) port(3) HPT with 73 mm (2.875 inch) port(4) HPD with 92.1 mm (3.625 inch) port(3) HPD with 73 mm (2.875 inch) port(4) HPT with 92.1 mm (3.625 inch) port(3) HPT with 73 mm (2.875 inch) port(4) HPD with 136.5 mm (5.375 inch) port HPT with 136.5 mm (5.375 inch) port HPD with 136.5 mm (5.375 inch) port(3) HPD with 111.1 mm (4.375 inch) port(4) HPT with 136.5 mm (5.375 inch) port(3) HPT with 111.1 mm (4.375 inch) port(4) HPD with 136.5 mm (5.375 inch) port(3) HPD with 111.1 mm (4.375 inch) port(4) HPT with 136.5 mm (5.375 inch) port(3) HPT with 111.1 mm (4.375 inch) port(4) - Continued MATERIAL DESCRIPTION S20910(1) (For Standard Bonnet) 1L4001X0042 1L4001X0042 10A6088X052 1K5879X0032 1K7891X0242 1L8776X0032 10A3282X222 1N3256X0052 11A3429XG82 1N3256X0052 11A3429XG52 1N6682X0072 11A3429XG52 1K7783X0032 1P5164X0152 1L2687X0152 S31600(2) (For Standard Bonnet) 1L400135162 1L400135162 10A6088X012 1K587935162 1K7891X0012 1L877635162 10A3282X012 1N325635162 11A3429XN62 1N325635162 11A3429X232 1N6682X0032 11A3429X232 1K778335162 1P516435162 1L2687X0012

Key 6* Valve Plug Stem for Class 1500 Standard and Whisper Valves with Whisper Trim III Cage (Continued)
VALVE ACTUATOR SIZE, GROUP INCHES

19.1

0.75

38, 50.8

1.5, 2

38

1.5

100

25.4

50.8

101

25.4

38, 50.8

1.5, 2

19.1

0.75

63.5, 76.2

2.5, 3

1U5071X0042

1J507135162

10A3282X222 1K7783X0032 10A3282X222 1K7783X0032 11A3429XG52 1L2687X0152 11A3429XG52 1L2687X0152

10A3282X012 1K778335162 10A3282X012 1K778335162 11A3429X232 1L2687X0012 11A3429X232 1L2687X0012

63.5 6 100 25.4 1

2.5

76.2

*Recommended spare parts

43

Instruction Manual

HP and HPA Valves


Key 6* Valve Plug Stem for Class 1500 Standard and Whisper Valves with Whisper Trim III Cage (Continued)
VALVE ACTUATOR SIZE, GROUP INCHES VALVE STEM CONNECTION mm Inches mm VALVE STEM TRAVEL Inches HPD with 136.5 mm (5.375 inch) port(3) HPD with 111.1 mm (4.375 inch) port(4) HPT with 136.5 mm (5.375 inch) port(3) HPT with 111.1 mm (4.375 inch) port(4) HPD with 136.5 mm (5.375 inch) port(3) HPD with 111.1 mm (4.375 inch) port(4) HPT with 136.5 mm (5.375 inch) port(3) HPT with 111.1 mm (4.375 inch) port(4) HPD with 136.5 mm (5.375 inch) port HPT with 136.5 mm (5.375 inch) port HPD with 136.5 mm (5.375 inch) port HPT with 136.5 mm (5.375 inch) port HPD with 136.5 mm (5.375 inch) port(3) HPD with 111.1 mm (4.375 inch) port(4) HPT with 136.5 mm (5.375 inch) port(3) HPT with 111.1 mm (4.375 inch) port(4) HPD with 136.5 mm (5.375 inch) port(3) HPD with 111.1 mm (4.375 inch) port(4) HPT with 136.5 mm (5.375 inch) port(3) HPT with 111.1 mm (4.375 inch) port(4) 31.8 x 50.8 1.25 x2 HPD with 136.5 mm (5.375 inch) port HPT with 136.5 mm (5.375 inch) port MATERIAL DESCRIPTION S20910(1) (For Standard Bonnet)

Form 5299 April 2004

S31600(2) (For Standard Bonnet)

63.5

2.5

1L2298X0202

1L2298X0012

31.8

1.25

100

76.2

10A6073X072

10A6073X012

63.5 31.8 x 50.8 6 1.25 x2 76.2

2.5

29A5895X482

---

29A5895X472

---

11A3429XG52 1L2687X0152 11A3429XG52 1L2687X0152

11A3429X232 1L2687X0012 11A3429X232 1L2687X0012

25.4

63.5, 76.2

2.5, 3

101 31.8 1.25 63.5, 76.2 2.5, 3

10A6073X072

10A6073X012

63.5, 76.2

2.5, 3

29A5895X472

---

1. Manufactured in U.S.A. 2. Manufactured in Europe and Japan. 3. Standard trim and Whisper Trim III Levels A1, A3, B3, C3. 4. Whisper Trim III Level D3.

44

*Recommended spare parts

Instruction Manual
Form 5299 April 2004

HP and HPA Valves


VALVE STEM CONNECTION mm Inches 19.1 12.7 0.5 19.1 19.1, 29 19.1 12.7 0.75 0.5 0.75 19.1, 29 19.1, 25.4, 29, 38 19.1, 25.4, 29, 38 mm 0.75 0.75 0.75, 1.125 0.75, 1.125 0.75, 1, 1.125, 1.5 0.75, 1, 1.125, 1.5 VALVE STEM TRAVEL Inches Micro-Form or MicroFlute with 6.4 mm (0.25-inch) port Micro-Flute with 9.5 or 12.7 mm (0.375 or 0.5 inch) port Micro-Form with 12.7, 19.1 or 25.4 mm (0.5, 0.75, or 1-inch) port Micro-Form with 19.1 or 25.4 mm (0.75 or 1-inch) port Micro-Form HPD, HPT, HPS Micro-Form HPD, HPT MATERIAL DESCRIPTION S20910 (For Standard Bonnet)

Key 6* Valve Plug Stem for Design HP Class 2500 Standard and Whisper Valves with Whisper Trim III Cage
VALVE ACTUATOR SIZE, GROUP INCHES

1N8210X0092 1N8210X0092 10A8840XT82 10A9265XV62 1U2263X0082 10A9265XV72

1 19.1

Key 7* Pin, 316 Stainless Steel (Globe Valve Body) VALVE RATING, CLASS VALVE SIZE, INCHES 1 2 1500 3 4 6 STEM DIAMETER DESIGN HPS HPS HPD, HPT HPS HPD, HPT HPD, HPT HPD, HPT 12.7 mm (0.5 Inch) 1B599635072 1B599635072 1V322735072 --1V322735072 ----19.1 mm (0.75 Inch) 1C5093X0022 1F723635072 1V322735072 1F723635072 1V326035072 1V326035072 1V326035072 25.4 mm (1-Inch) --1D269735072 --1D269735072 1V334035072 1V334035072 1V334035072 31.8 mm (1.25 Inch) ------------1V334035072 31.8 x 50.8 mm (1.25 x 2-Inch) ------------15A4000X012

Key 7* Pin, 316 Stainless Steel (Angle Valve Body) VALVE RATING, CLASS VALVE SIZE, INCHES DESIGN PORT SIZE 0.25, 1.5 0.75, 1 All 0.375, 0.5 0.75 0.75 0.25, 1.5 Micro-Form 1500 Micro-Flute Micro-Flat 2 HPAS 0.75 1, 1.25, 1.5 All 1 0.75 1 1.25 1.5 1.875 HPAD, HPAT 1.875 STEM DIAMETER 12.7 mm (0.5 Inch) 1B599635072 1B599635072 1B599635072 1B599635072 ----1B599635072 1B599635072 1B599635072 1B599635072 ----------1B599635072 1V322735072 19.1 mm (0.75 Inch) --1C5093X0022 ----1C5093X0022 1B627035072 --1F723635072 1F723635072 --1F723635072 1B627035072 1B599635072 ----1F723635072 1V322735072 25.4 mm (1-Inch) ----------------1D269735072 --------1B813635072 1K249735072 1D269735072 ---

Micro-Form 1 Micro-Flute Micro-Flat HPAS

*Recommended spare parts

45

Instruction Manual

HP and HPA Valves


Key 8* Graphite Piston Ring for Design HPD (2- to 6-Inch) and HPAD (2-inch) Only VALVE SIZE, INCHES 2 3 4 6 QUANTITY mm 2 2 2 2 4 3 47.6 73.0 73.0 92.1 111.1 136.5 PORT DIAMETER Inches 1.875 2.875 2.875 3.625 4.375 5.375 CLASS 1500 253_C to 426_C (425_F to 800_F) 1U2216X0012 1U2300X0012 1U2300X0012 16A5482X012 1U2392X0012 11A9727X022

Form 5299 April 2004

427_C to 537_C (801_F to 1000_F) 1U2216X0022 1U2300X0022 1U2300X0022 16A5482X022 1U2392X0022 11A9727X032

Key 8* Seal Ring and Key 39* Graphite Piston Ring for Design HPT (2- to 6-inch) and HPAT (2-inch only) without Cavitrol III Trim, Hastelloy with Glass and Moly-Filled PTFE VALVE SIZE, INCHES 2 3 4 6 Without Whisper Trim III 6 With Whisper Trim III PORT DIAMETER mm 47.6 73.0 73.0 92.1 111.1 136.5 111.1 136.5 Inches 1.875 2.875 2.875 3.625 4.375 5.375 4.375 5.375 KEY 8 SEAL RING Valve Body Rating Class 1500 10A4216X012 10A4215X012 10A4215X012 16A5485X012 10A4223X012 10A5411X022 10A4223X012 10A5411X022 KEY 39 PISTON RING ------------1U2392X0012(1) ---

1. For use only with Whisper Trim III Level D with 111.1 mm (4.375 inch) port.

Key 8* Seal Ring for Cavitrol III Trim Only, Hastelloy with Glass and Moly-Filled PTFE VALVE SIZE, INCHES 2 3 4 6 2-STAGE 17A2296X012 17A4309X012 10A5351X022 17A4396X012 3-STAGE --10A4216X012 10A4215X012 17A4413X012

Key 9* Back-Up Ring for All Design HPT (2- to 6-inch) and HPAT (2-inch only) Valves Except Those with Cavitrol III Trim VALVE SIZE, INCHES 2 3 4 6 PORT DIAMETER mm 47.6 73.0 73.0 92.1 111.1 136.5 Inches 1.875 2.875 2.875 3.625 4.375 5.375 S31600 (316 SST) 10A4218X012 10A4217X022 10A4217X022 16A5483X022 10A4224X022 10A5409X022 MATERIAL S41600 (416 SST) 10A4218X022 10A4217X012 10A4217X012 16A5483X012 10A4224X012 10A5409X012

46

*Recommended spare parts

Instruction Manual
Form 5299 April 2004

HP and HPA Valves


PORT DIAMETER mm 44.5 63.5 47.6 87.3 73.0 133.4 115.8 Inches 1.75 2.5 1.875 3.4375 2.875 5.25 4.5625 S41600 (416 SST) 13A8520X012 17A4310X012 10A4218X022 10A5349X012 10A4217X012 17A4397X012 17A4414X012 MATERIAL S31600 (316 SST) 13A8520X022 17A4310X022 10A4218X012 10A5349X022 10A4217X022 17A4397X022 17A4414X022

Key 9* Back-Up Ring for Design HPT (2- to 6-inch) and HPAT (2-inch only) Valves with Cavitrol III Trim VALVE SIZE, INCHES 2 (2-Stage) 3 (2-Stage) 3 (3-Stage) 4 (2-Stage) 4 (3-Stage) 6 (2-Stage) 6 (3-Stage)

Keys 5*, 8*, 9*, 10*, and 63* Design HPT Above 232_C (450_F) Using PEEK(1) Anti-Extrusion Rings VALVE SIZE, INCHES 2 3 PORT DIAMETER mm Std, Whisper III Std, Whisper III Std, Whisper III A,B,C Whisper III D 47.6 73.0 KEY 63 KEY 8 KEY 9 Back-Up Ring S41600 10A4218X022 10A4218X022 10A4217X012 10A4217X012 10A4217X012 16A5483X012 16A5483X012 10A4217X012 10A4217X012 10A5409X012 10A5409X012 10A5409X012 10A5409X012 10A5409X012 10A5409X012 10A4224X012 10A4224X012 KEY 10 Retaining Ring S30200 10A4220X012 10A4220X012 10A4219X012 10A4219X012 10A4219X012 16A5484X012 16A5484X012 10A4219X012 10A4219X012 10A5410X012 10A5410X012 10A5410X012 10A5410X012 10A5410X012 10A5410X012 10A4225X012 10A4225X012 KEY 5 Anti-Extrusion Valve Plug S41600 31B2146X012 31B2147X012 31B2148X012 31B2149X012 31B2150X012 31B2151X012 31B2152X012 31B2149X012 31B2150X012 31B2153X012 31B2154X012 31B2154X022 31B2155X012 31B2155X022 31B2156X012 31B2134X022 31B2135X022 Anti-Extrusion Seal Ring Ring Inches PEEK N10276/PTFE 1.875 2.875 22B4694X012 22B4694X012 22B2617X012 22B2617X012 22B2617X012 21B2115X012 21B2115X012 22B2617X012 22B2617X012 21B9342X012 21B9342X012 21B9342X012 21B9342X012 21B9342X012 21B9342X012 21B9341X012 21B9341X012 10A4216X032 10A4216X032 10A4215X032 10A4215X032 10A4215X032 16A5485X062 16A5485X062 10A4215X032 10A4215X032 10A5411X032 10A5411X032 10A5411X032 10A5411X032 10A5411X032 10A5411X032 10A4223X032 10A4223X032 STEM CONNECTOR DIAMETER mm 12.7 19.1 12.7 19.1 25.4 19.1 25.4 19.1 25.4 19.1 25.4 25.4 31.8 31.8 50.8 25.4 31.8 Inches 0.5 0.75 0.5 0.75 1 0.75 1 0.75 1 0.75 1 1 1.25 1.25 2 1 1.25

TRIM

4 4

92.1 73.0

3.625 2.875

DIA B DIA B Std, DIA C 136.5 Whisper III DIA B A,B,C DIA C DIA B Whisper III 111.1 D

5.375

4.375

1. PolyEtherEtherKetone.

Gasket Set* (Includes Key 11 Bonnet Gasket and Key 12 Seat Ring Gasket)(1) VALVE RATING, CLASS VALVE SIZE, INCHES 1 (std) 2 (std) 1500 Globe and Angle Valves 2 (Cavitrol III, 2-Stage) 3 (std) 4 (std) 6 (std) 1 (std) 2500 Globe and Angle Valves 2 (std) 2 (Cavitrol III, 2-Stage) MATERIAL N06600 (Inconel 600)/Graphite 12B7100X012 12B7100X032 12B7100X072 12B7100X052 12B7100X082 12B7100X112 ------N07750 (Inconel X750)/Graphite 12B7100X022 12B7100X042 --12B7100X062 ----12B7100X122 12B7100X132 12B7100X142

1. Gaskets should always be replaced as sets, not separately.

*Recommended spare parts

47

Instruction Manual

HP and HPA Valves

Form 5299 April 2004

C-seal is a mark owned by Pressure Science, Inc. Cavitrol, ENVIRO-SEAL, FIELDVUE, Fisher, HIGH-SEAL, Micro-Flat, Micro-Flute, MicroForm, and Whisper Trim are marks owned by Fisher Controls International LLC, a business of Emerson Process Management. The Emerson logo is a trademark and service mark of Emerson Electric Co. All other marks are the property of their respective owners. This product is covered by one or more of the following patents: 5,129,625; 5,131,666; 5,056,757; 5,230,498; and 5,299,812 or under pending patents The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. We reserve the right to modify or improve the designs or specifications of such products at any time without notice. Fisher does not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and maintenance of any Fisher product remains solely with the purchaser and end-user. Emerson Process Management Fisher Marshalltown, Iowa 50158 USA Cernay 68700 France Sao Paulo 05424 Brazil Singapore 128461 www.Fisher.com
48 EFisher Controls International LLC 1991, 2004; All Rights Reserved Printed in USA

You might also like