BM Tda1517p

BM Semiconductors
2 6 W Hi-fi stereo power amplier

FEATURES Requires very few external components High output power Fixed gain Good ripple rejection Mute/standby switch AC and DC short-circuit safe to ground and VP Thermally protected Meet the Hi-Fi audio performance Capability to handle high energy on outputs (VP = 0 V) Almost no switch-on/switch-off pop noise Electrostatic discharge protection. QUICK REFERENCE DATA SYMBOL VP IORM Iq(tot) Isb Isw |ZI| Po SVRR cs Gv Vno(rms) Tc PARAMETER supply voltage repetitive peak output current total quiescent current standby current switch-on current input impedance output power supply voltage ripple rejection channel separation closed loop voltage gain noise output voltage (RMS value) crystal temperature RL = 4 ; THD = 0.5% RL = 4 ; THD = 10% fi = 100 Hz to 10 kHz CONDITIONS 50 48 40 19 MIN. 6.0 40 0.1 5 6 20 50 TYP. 14.4 GENERAL DESCRIPTION
TDA1517P
The BM TDA1517P is an integrated class-AB dual output amplifier in a plastic DIP18 power package. It can delivery 2*6W with a great low Iq standby mode. The device is primarily designed for LCD-TV, monitor and for multi-media AV center Hi-Fi applications.
MAX. 18.0 2.5 80 100 40 21 150
UNIT V A mA A A k W W dB dB dB V C
Notes: Not only the Signal to Noise(S/N), also the Frequency Response(FR), the Hi-Fi BM-TDA1517P is much better than SL1517 and YD1517, and the switch on-off pop noise is lowest, which the performance customer can verify ! It can pin to pin replace YD1517 and SL1517 or D1517 without changing PCB or external.
2011-Jan
www.bookly.com
Bookly Micro
2 6 W stereo power amplier

BLOCK DIAGRAM
TDA1517P
handbook, full pagewidth
non-inverting input 1
1 60 k
mute switch
Cm
4 VA 2 k 18 k power stage
output 1
VP 8 stand-by switch VA 15 k x1 supply voltage ripple rejection output 3 15 k mute reference voltage 18 k mute switch stand-by reference voltage mute/stand-by switch input
TDA1517
2 k non-inverting input 2 VA 9 60 k input reference voltage mute switch signal ground 2 SGND 7 VP Cm power stage power ground 5 (substrate)
MLC351
output 2
PGND
Fig.1 Block diagram.
2011-Jan
www.bookly.com
Bookly Micro

PINNING SYMBOL INV1 SGND SVRR OUT1 PGND OUT2 VP M/SS INV2 PIN 1 2 3 4 5 6 7 8 9 input 1 signal ground supply voltage ripple rejection output output 1 power ground output 2 supply voltage mute/standby switch input input 2 DESCRIPTION
TDA1517P
ndbook, halfpage
INV1 SGND SVRR OUT1 PGND OUT2 VP M/SS INV2
1 2 3 4 5 6 7 8 9
MLC353
18 17 16 15 TDA1517P 14 13 12 11 10
Pins 10 to 18 should be connected to large area GND for heatsink .
Fig.3 Pin configuration for DIP18
FUNCTIONAL DESCRIPTION The TDA1517 contains two identical amplifiers with differential input stages. The gain of each amplifier is fixed at 20 dB. A special feature of the device is the mute/standby switch which has the following features: Low standby current (<100 A) Low mute/standby switching current (low cost supply switch) Mute condition. 2011-Jan 3 www.bookly.com
Bookly Micro

LIMITING VALUES In accordance with the Absolute Maximum Rating System . SYMBOL VP VP(sc) VP(r) ERGO IOSM IORM Ptot Tstg Tamb Tc PARAMETER supply voltage AC and DC short-circuit safe voltage reverse polarity energy handling capability at outputs non-repetitive peak output current repetitive peak output current total power dissipation storage temperature operating ambient temperature crystal temperature see Fig.4 VP = 0 V CONDITIONS 45 20 MIN.
TDA1517P
MAX. 18 18 6 200 4 2.5 15 +150 +85 150 V V V
UNIT
mJ A A W C C C
THERMAL RESISTANCE SYMBOL Rth j-c Rth j-p Rth j-a TYPE NUMBER TDA1517P TDA1517P TDA1517P PARAMETER thermal resistance from junction to case thermal resistance from junction to pins 8 15 VALUE UNIT K/W K/W K/W
thermal resistance from junction to ambient 50
handbook, halfpage
18
MLC354
P (W) 12 (1)
(2) 6
0 25 0 50 100 150 o T amb ( C)
(1) Rth j-c = 8 K/W. (2) Rth j-p = 15 K/W.
Fig.4 Power derating curve.
2011-Jan
www.bookly.com
Bookly Micro

DC CHARACTERISTICS VP = 14.4 V; Tamb = 25 C; measured in Fig.6; unless otherwise specied. SYMBOL Supply VP Iq(tot) VO V8 VO Isb Vsw Note 1. The circuit is DC adjusted at VP = 6 to 18 V and AC operating at VP = 8.5 to 18 V. supply voltage total quiescent current DC output voltage note 1 6.0 14.4 40 6.95 12 PARAMETER CONDITIONS MIN. TYP.
TDA1517P
MAX.
UNIT
18.0 80
V mA V
Mute/standby switch switch-on voltage level see Fig.5 8.5 V
Mute condition output signal in mute position VI(max) = 1 V; fi = 20 Hz to 15 kHz 2 mV A A
Standby condition DC current in standby condition switch-on current 100 40
2011-Jan
www.bookly.com
Bookly Micro

AC CHARACTERISTICS VP = 14.4 V; RL = 4 ; f = 1 kHz; Tamb = 25 C; measured in Fig.6; unless otherwise specied. SYMBOL Po THD flr fhr Gv SVRR PARAMETER output power total harmonic distortion low frequency roll-off high frequency roll-off closed loop voltage gain supply voltage ripple rejection on mute standby |Zi| Vno input impedance noise output voltage on on mute cs |Gv| Notes 1. Output power is measured directly at the output pins of the IC. 2. Frequency response externally fixed. channel separation channel unbalance Rs = 0 ; note 4 Rs = 10 ; note 4 note 5 Rs = 10 40 50 70 50 0.1 note 3 48 48 80 50 60 75 CONDITIONS THD = 0.5%; note 1 THD = 10%; note 1 Po = 1 W at 3 dB; note 2 at 1 dB 4 5.5 20 19 MIN. 5 6.0 0.1 45 20 TYP. 21
TDA1517P
MAX.
UNIT W W % Hz kHz dB dB dB dB k V V V dB dB
100 1
3. Ripple rejection measured at the output with a source impedance of 0 , maximum ripple amplitude of 2 V (p-p) and a frequency between 100 Hz and 10 kHz. 4. Noise voltage measured in a bandwidth of 20 Hz to 20 kHz. 5. Noise output voltage independent of Rs (VI = 0 V).
2011-Jan
www.bookly.com
Bookly Micro
TDA1517P
handbook, halfpage
18 V11 (V)
8.5 6.4
3.3 2 0
,,,,,,, ,,,,,,, ,,,,,,, ,,,,,,, ,,,,,,, ,,,,,,, ,,,,,,, ,,,,,,,

MLC355
ON (IP = 40 mA)
mute (IP = 40 mA)
standby (I P
100 A)
Fig.5 Standby, mute and on conditions.
APPLICATION INFORMATION
handbook, full pagewidth
standby switch 100 F 3 input reference voltage internal 1/2 V P 8 7 VP 100 nF 2200 F
TDA1517
220 nF input 1 60 k 1 20 dB 20 dB 60 k 9 220 nF input 2
5 1000 F
6
MLC356
signal ground
power ground
1000 F
Fig.6 Application circuit diagram.
2011-Jan
www.bookly.com
Bookly Micro
TDA1517P
DIP18: plastic heat-dissipating dual in-line package; 18 leads
D seating plane
ME
A2
A1 L
b1 b b2 10
w M
c (e 1) MH
18
pin 1 index E
5 scale
10 mm
DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT mm inches A max. 4.7 0.19 A1 min. 0.51 0.02 A2 max. 3.7 0.15 b 1.40 1.14 0.06 0.04 b1 0.67 0.50 0.03 0.02 b2 1.05 0.75 0.04 0.03 c 0.47 0.38 0.02 0.01 D (1) 21.85 21.35 0.87 0.84 E (1) 6.5 6.2 0.26 0.24 e 2.54 0.10 e1 7.62 0.30 L 3.9 3.1 0.15 0.12 ME 8.32 8.02 0.33 0.32 MH 8.7 7.7 0.34 0.30 w 0.25 0.01 Z (1) max. 1.0 0.04
Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
2011-Jan
www.bookly.com

BM Tda1517p

Uploaded by

Copyright:

Available Formats

BM Tda1517p

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

BM Tda1517p

Uploaded by

Copyright:

Available Formats

BM Semiconductors

2 6 W Hi-fi stereo power amplier

MAX. 18.0 2.5 80 100 40 21 150

2 6 W stereo power amplier

handbook, full pagewidth

Fig.1 Block diagram.

2 6 W stereo power amplier

INV1 SGND SVRR OUT1 PGND OUT2 VP M/SS INV2

Pins 10 to 18 should be connected to large area GND for heatsink .

Fig.3 Pin configuration for DIP18

2 6 W stereo power amplier

MAX. 18 18 6 200 4 2.5 15 +150 +85 150 V V V

thermal resistance from junction to ambient 50

0 25 0 50 100 150 o T amb ( C)

(1) Rth j-c = 8 K/W. (2) Rth j-p = 15 K/W.

Fig.4 Power derating curve.

2 6 W stereo power amplier

Mute/standby switch switch-on voltage level see Fig.5 8.5 V

Mute condition output signal in mute position VI(max) = 1 V; fi = 20 Hz to 15 kHz 2 mV A A

Standby condition DC current in standby condition switch-on current 100 40

2 6 W stereo power amplier

2 6 W stereo power amplier

,,,,,,, ,,,,,,, ,,,,,,, ,,,,,,, ,,,,,,, ,,,,,,, ,,,,,,, ,,,,,,,

mute (IP = 40 mA)

Fig.5 Standby, mute and on conditions.

handbook, full pagewidth

Fig.6 Application circuit diagram.

2 6 W stereo power amplier

DIP18: plastic heat-dissipating dual in-line package; 18 leads

You might also like