Ece III Network Analysis (10es34) Notes

Network Analysis
10ES34
PART A
UNIT 1: Basic Concepts: Practical sources, Source transformations, Network reduction using Star Delta transformation, Loop and node analysis With linearly dependent and independent sources for DC and AC networks, Concepts of super node and super mesh 7 Hours UNIT 2:
Network Topology: Graph of a network, Concept of tree and co-tree, incidence matrix, tie-set, tie-set and cut-set schedules, Formulation of equilibrium equations in matrix form, Solution of resistive networks, Principle of duality. 7 Hours
UNIT 3:
Network Theorems 1: Superposition, Reciprocity and Millmans theorems
UNIT 4: Network Theorems - II:
Thevinins and Nortons theorems; Maximum Power transfer theorem 6 Hours
TS
UNIT 5: Resonant Circuits: Series and parallel resonance, frequency-response of series and Parallel circuits, Q factor, Bandwidth. 6Hours
CI
UNIT 6:
Transient behavior and initial conditions: Behavior of circuit elements under switching condition and their Representation, evaluation of initial and final conditions in RL, RC and RLC circuits for AC and DC excitations.
TU D
EN
PART B
UNIT 7: Laplace Transformation & Applications : Solution of responses, waveform Synthesis networks, step, ramp and impulse
CITSTUDENTS.IN
TS .IN
6 Hours
7 Hours
Network Analysis
10ES34
7 Hours
UNIT 8: Two port network parameters: Definition of z, y, h and transmission parameters, modeling with these parameters, relationship between parameters sets 6 Hours TEXT BOOKS: 1. Network Analysis, M. E. Van Valkenburg, PHI / Pearson Education, 3rd Edition. Reprint 2002. 2. Networks and systems, Roy Choudhury, 2nd edition, 2006 re-print, New Age International Publications.
Question Paper Pattern: Student should answer FIVE full questions out of 8 questions to be set each carrying 20 marks, selecting at least TWO questions from each part.
Coverage in the Texts:
UNIT 1: Text 2: 1.6, 2.3, 2.4 (Also refer R1:2.4, 4.1 to 4.6; 5.3, 5.6; 10.9 This book gives concepts of super node and super mesh) UNIT 2: Text 2: 3.1 to 3.11
UNIT 5: Text 2 8.1 to 8.3
UNIT 6: Text 1 Chapter 5;
UNIT 7: Text 1 7.4 to 7.7; 8.1 to 8.5
CI
CITSTUDENTS.IN
UNIT 8: Text 1 11.1 to 11.
TS
UNIT 3 and UNIT 4: Text 2 7.1 to 7.7
TU D
EN
REFERENCE BOOKS: 1. , Engineering Circuit Analysis, Hayt, Kemmerly and DurbinTMH 6th Edition, 2002 2. Network analysis and Synthesis, Franklin F. Kuo, Wiley International Edition, 3. Analysis of Linear Systems, David K. Cheng, Narosa Publishing House, 11th reprint, 2002 4. Circuits, Bruce Carlson, Thomson Learning, 2000. Reprint 2002
TS .IN
Network Analysis
10ES34
INDEX SHEET
SL.NO 1 UNIT 01 UNIT 01 UNIT 01 UNIT 01 UNIT 01 UNIT 01 UNIT 01 UNIT 01 University syllabus 1: Basic Concepts Assignment Questions - 2: Network Topology Assignment Questions - 3: Network Theorems 1 Assignment Questions - 4: Network Theorems - II Assignment Questions - 5: Resonant Circuits Assignment Questions - 6: Transient behavior and initial conditions Assignment Questions 7: Laplace Transformation & Applications Assignment Questions 8: Two port network parameters Assignment Questions TOPIC PAGE NO. 2-3 5-14 15-17 18-37 38-39 40-47 48-49 50-58 59-60 61-69 70-71 72-83 84-85 86-95 96-97 98-110 111-112
CI
CITSTUDENTS.IN
TS
TU D
EN
TS .IN
3
Network Analysis
10ES34
Unit: 1 : Basic Concepts Syllabus of unit 1:
Hrs: 07
Practical sources, Source transformations, Network reduction using Star Delta transformation, Loop and node analysis With linearly dependent and independent sources for DC and AC networks Concepts of super node and super mesh.
Recommended readings:
1. Network Analysis, M. E. Van Valkenburg, PHI / Pearson Education
2. Networks and systems, Roy Choudhury, 2 edition, New Age International Publications .
4. Network analysis , Roy Choudry.
CI
CITSTUDENTS.IN
TS
TU D
EN
4
3. Network theory , Ganesh Rao.
TS .IN
Network Analysis
10ES34
BASIC LAWS:
1. OHMS LAW IAB-Current from A to B
V=IZ
IAB +
Z VAB -
VAB=Voltage of A w.r.t B
2. KCL i1+i4+i5=i2+i3
i1 i2 i3 i4 i5
I2 V1 E1 + + Z1 I1 +
Z2
EN
+ + - E2 vrise= Z3 V3 I3 -
3. KVL
V2
Reference Direction E1-E2=V1 -V2+V3-V4=I1Z1 -I2 Z2+I3Z3-I4Z4
TS
SERIES + V1 - + V 2 + Vn Z1
TU D
I4 Z4 V4
Zn
CONNECTIONS
PARELLEL
Z2
CI
Z=
1
Z K = Z1 + Z 2 + Z 3 Z n
Y=
1
Voltage Division Vi =(Zi/Z)V
Current Division II=(Yi/Y)I
CITSTUDENTS.IN
TS .IN
or i=0 algebraic sum iin= iiout ( Iin=-Iout) v=0 algebraic sum vdrop (Vrise= Vdrop)
Y1 Y2 Yn
I1
I2
In
YK = Y1 + Y2 + Y3 Yn
Network Analysis I=V/Z=V1/Z1=V2/Z2=-------------V=I/Y=I1/Y1=I2/Y2=-------------
10ES34
Problems
1.Calculate the voltages V12,V23,V34 in the network shown in Fig, if Va=17.32+j10 Vb=30 80 0 V and VC=15 -100V with Calculator in complex and degree mode V12 = -Vc + Vb 3 = (0-15 -100 +30 80 ) = 45 800 V * + Va V23 = Va-Vb+Vc = Va V12 = 17.32+10i- 45 800 = 35.61 -74.520 + Vc 0 V34 = Vb - Va = 30 80 - 17.32-10i = 23 121.78 1 2 4
EN
I2 7[2
3. In the circuit determine what voltage must be applied across AB in order that a current of 10 A may flow in the capacitor I1 5[2 6[2 8[2 10 [2
TS
I2 = V = (30.6 9.550 ) Z2 I3 = V = (30.6 9.550 ) Z2
TU D
2.How is current of 10A shared by 3 impedances Z1=2-J5[2 Z2 = 6.708 26.56 and Z3 = 3 + J4 all connected in parallel Ans: Z = Y-1 = ((2-5i)-1 + (6.708 26.56)-1 +(3+4i)-1 = 3.06 9.550 V=1Z = 30.6 9.550 I1 = V/Z1=(30.6 9.550 ) : (2-5i) =5.68 77.750 : (6.708 26.56) = 4.56 -170 : (3+4i) = 6.12 -43.60
TS .IN
+ Vb
C
CI
8[2
VAC= (7-8i)(10) = 106.3 -48.80
I1 = VAC = 13.61 -990 5+6i I = I1+I2 = 10 00 +13.61 -990 = 15.576 -59.660 V =V1+V2 = 106.3 -48.8 + (15.576 -59.66) (8+10i)=289 -220
CITSTUDENTS.IN
Network Analysis
10ES34
Practical sources:
Network is a system with interconnected electrical elements. Network and circuit are the same. The only difference being a circuit shall contain at least one closed path. Electrical Elements Sources Independent Sources M Dependant Sources N Passive Elements R (Energy Consuming Element) L C (Energy storing (Energy storing element in a magnetic field) element in an Electric field)
EN
B (a) N
Voltage Source (ideal)
Current Source (ideal)
TS .IN
kix gvx +kvx (b) (c) (a)Current controlled current source (b) Voltage controlled current source (c) Voltage controlled voltage source (d) Current controlled voltage source (Source quantity is determined by a voltage or current existing at some other Location in the circuit) These appear in the equivalent models for many electronic devices like transistors, OPAMPS and integrated circuits.
+vix (d)
E +
CI
CITSTUDENTS.IN
TS
M (Value of source Quantity is not affected in anyway by activities in the reminder of the circuit.)
TU D
Network Analysis
10ES34
gV1 C1 i1
Voltage controlled current source Node (Junction) Ki1 Current controlled Voltage source
TS .IN
Practical current source
Practice Voltage source
Mesh (loop)
Loop
Reference node
TYPES OF NETWORKS
The network not satisfying this condition is nonlinear Ex:- Linear Resistors, Inductors, Capacitors. Nonlinear Semiconductors devices like transistors, saturated iron core inductor, capacitance of a p-n function. Passive and active Networks: A Linear network is passive if (i) the energy delivered to the network is nonnegative for any excitation. (ii) no voltages and currents appear between any two terminals before any excitation is applied. Example:- R,L and C.
CI
CITSTUDENTS.IN
Active network:- Networks containing devices having internal energy Generators, amplifiers and oscillators. Unilateral & Bilateral: The circuit, in which voltage current relationship remains unaltered with the reversal of polarities of the source, is said to be bilateral. Ex:- R, L & C If V-I relationships are different with the reversal of polarities of the source, the circuit is said to be unilateral. Ex:- semiconductor diodes.
TS
TU D
Linear and Nonlinear Networks: A network is linear if the principle of superposition holds i.e if e1(t), r1 (t) and e2(t), r2 (t) are excitation and response pairs then if excitation is e1 (t) + e2 (t) then the response is r1 (t) + r2(t).
EN
Network Analysis
10ES34
Lumped & Distributed: Elements of a circuit, which are separated physically, are known as lumped elements. Ex:- L & C. Elements, which are not separable for analytical purposes, are known as distributed elements. Ex:- transmission lines having R, L, C all along their length. In the former care Kirchhoffs laws hold good but in the latter case Maxwells laws are required for rigorous solution. Reciprocal: A network is said to be reciprocal if when the locations of excitation and response are interchanged, the relationship between them remains the same.
Source Transformation:
ZS ES
a ZL
EN
IS ZP IL = IS .Z P
Z p + ZL
In network analysis it may be required to transform a practical voltage source into its equivalent practical current source and vice versa . These are done as explained below a ZL
b b fig 1 fig 2 Consider a voltage source and a current source as shown in Figure 1 and 2. For the same load ZL across the terminals a & b in both the circuits, the currents are IL= ES Z s+ZL in fig 1 and in fig 2
For equivalence ES = IS ZS+ZL Therefore ES = IS Z P and ZS = Z P
TS
IS =
CI
Therefore CITSTUDENTS.IN
ES ES = ZP ZS Transformation from a practical voltage source to a practical current source eliminates a node. Transformation from a practical current source to a current source eliminates a mesh. A practical current source is in parallel with an impedance Zp is equivalent to a voltage source Es=Is Zp in series with Zp. A practical voltage source Es in series with a impedance Zs is equivalent to a current source Es/Zs in parallel with Zs.
TU D
.
ZP Z P+ZL
TS .IN
Network Analysis
10ES34
SOURCE SHIFTING:
Source shifting is occasionally used to simplify a network. This situation arises because of the fact than an ideal voltage source cannot be replaced by a current source. Like wise ideal current source cannot be replaced by a voltage source. But such a source transformation is still possible if the following techniques are fallowed. c Z3 a Z1 + E _O x Z2 + x E b a c Z3
Z1
(a) E shift operation
TU D
Z4
EN
Z1 Z4 I Z2 Z3 I
Z1
TS
Z2
TS .IN
+ x E E + Z2 b x O I Z1 Z2 Z4 I Z3 I 10
CI
CITSTUDENTS.IN
Z3
(b) I shift operation
Network Analysis
10ES34
Sources with equivalent terminal characteristics
+ V1 V2 + -
+ V1+V2 V1
+ -
+ V2=V1
+ v1=v2
(i)Series voltage sources
(ii) Parallel voltage sources(ideal)
i1
i2
i1+i2
(iii) Parallel current sources
+ V z Z
+ V -
EN
ZZ I + V I
(v)Voltage source with parallel Z
TU D
+ V I
TS
(vii) V and I in Parallel
CI
Delta-star transformation:
A set of star connected (Y o:r T) immittances can be replaced by an equivalent set of mesh ( or 7t) connected immittances or vice versa. Such a transformation is often necessary to simplify passive networks, thus avoiding the need for any mesh or nodal analysis.
For equivalence, the immittance measured between any two terminals under specified conditions must be the same in either case.
CITSTUDENTS.IN
TS .IN
i1 i1 i1=i2 (iv)Series current sources(ideal) I (vi)Current source with series Z - + V I (viii) V and I in Series 11
Network Analysis
10ES34
to Y transformation: Consider three -connected impedances ZAB, ZBC and ZCA across terminals A, B and C. It is required to replace these by an equivalent set ZA, ZB and ZC connected in star. A ZAB B ZBC ZAC C B ZB A ZA C ZC
In , impedance measured between A and B with C open is ZAB (ZBC + ZCA) ZAB+ ZBC + ZCA
With C open, in Y, impedance measured between A and B is ZA+ZB. ZAB (ZBC + ZCA) -----------(1) For equivalence ZA+ZB = ZAB+ ZBC + ZCA
Adding (1), (2) and (3)
2 (ZA+ ZB + ZC) = ZA =
Substituting for ZB + ZC from (2) = ZA = ZCA ZAB ZAB+ ZB + ZCA
TS
If
(ZAB ZBC + ZBCZCA + ZCAZAB) ZAB+ ZBC + ZCA
CI
Similarly by symmetry
TU D
Z
CA
For impedance measured between C and A with B open ZCA (ZAB + ZBC) ZC + ZA = --------------------------------(3) ZAB+ ZBC + ZCA
2 (ZAB ZBC + ZBCZCA + ZCAZAB) ZAB+ ZBC + ZCA - (ZB + ZC)
ZB = ZC =
ZAB ZBC ZAB ZBC ZCA ZAB Z!J . 3
ZAB = ZBC = ZCA = Z!J then ZA = ZB = ZC = ZY =
Y to A transformation: Consider three Y connected admittance Ya, Yb and Yc across the terminals A, B and C. It is required to replace them by a set of equivalent !J admittances Yab, Ybc and Yca. CITSTUDENTS.IN 12
EN
Z AB Z AB
Similarly for impedance measured between B and C with A open -----------------------------(2) ZB + ZC = ZBC (ZCA + ZAB) ZAB+ ZBC + ZCA
TS .IN
Network Analysis Admittance measured between A and B with B & C shorted In Y In !J YA (YB + YC) YA+ YB + YC YAB + YCA
10ES34
A YAB B
YAC C YBC YA (YB + YC) YA+ YB + YC
YA
For equivalence YAB + YCA =
-------------------------(1)
YAB =
YA YB - (YBC + YCA) YA substituting from (3)
YA YB YA YB YB YC : YBC = : YCA = Y + YB + YC A YA+ YB + YC YA+ YB + YC In terms of impedances, ZA ZB + ZBZC + ZCZA ZAB = YA + YB + YC = ZC YA YB Z Z + ZBZC + ZCZA Similarly ZBC = A B ZA ZA ZB + ZBZC + ZCZA ZCA = ZB If ZA = ZB = ZC = ZY then ZAB = ZBC = ZCA = Z!J = 3ZY .
CI
CITSTUDENTS.IN
TS
TU D
Admittance between C and A with A & B shorted YC (YA + YB) ---------------------------------(3) YCA + YBC = YA+ YB + YC YAYB + YBYC + YCYA Adding (1), (2) and (3) YAB + YBC + YCA = YA+ YB + YC
EN
Admittance between B and C with C & A shorted YBC + YAB = YB (YC + YA) ------------------------------------(2) YA+ YB + YC
TS .IN
C YC YB 13
Network Analysis
10ES34
Assignment questions:
1) Distinguish the following with suitable examples. i) Linear and non-linear elements. ii) Unilateral and trilateral elements. iii) Independent and dependent sources. 2) Write the mesh equation for the circuit shown in Fig. 1 and determine mesh currents using mesh analysis.
Fig. 1
3) Establish star delta relationship suitably 4) Using source transformation, find the power delivered by the'50 V voltage source in the circuit shown in Fig.
CI
CITSTUDENTS.IN
TS
5) Find the power delivered by the 5A current source in the circuit shown in Fig.4 by using the nodal method.
TU D
EN
14
TS .IN
Network Analysis
10ES34
6) For the network shown in fig. 2, determine the voltage V using source shift and / or source
transformation techniques only. Then verify by node equations
7) Use mesh current method to determine the current in the capacitor of 6 of the bridge network shown in fig. 5.
8) Use node equations to determine what value of E will cause Vx to be zero for the network
CI
CITSTUDENTS.IN
TS
shown in fig. 6.
TU D
EN
15
TS .IN
Network Analysis 9) Obtain the delta connected equipment of the network shown in fig. 1.
10ES34
10) c) Find the voltage across the capacitor of 20 reactance of the network shown in fig. 2, by reducing the network to contain one source only, by source transformation techniques.
11) c) Use 3 mesh equations for the network shown in fig. 5 to determine R and C. such that the
current in 3+j4 is zero . Take = 50 rad/sec.
CI
CITSTUDENTS.IN
TS
TU D
EN
TS .IN
16
Network Analysis
10ES34
Unit: 2
Network Topology :
Hrs: 07
Syllabus of unit
1. Network Analysis, M. E. Van Valkenburg, PHI / Pearson Education 2. Networks Publications . and systems, Roy Choudhury, 2 edition,
CI
CITSTUDENTS.IN
TS
TU D
EN
17
TS .IN
Graph of a network, Concept of tree and co-tree, incidence matrix, tie-set, tie-set and cut-set schedules, Formulation of equilibrium equations in matrix form, Solution of resistive networks, Principle of duality
New Age International
Network Analysis
10ES34
Net work Topology

Definition:
The term circuit topology refers to the science of placement of elements and is a study of the geometric configurations. Circuit topology is the study of geometric properties of a circuit useful for describing the circuit behavior Terms used in Topology: The following terms are often used in network topology Graph: In the given network if all the branches are represented by line segments then the resulting figure is called the graph of a network (or linear graph). The internal impedance of an ideal voltage source is zero and hence it is replaced by a short circuit and that of an ideal current source is infinity and hence it is represented by an open circuit in the graph. Example: Network
Branch (or Twig):
It is a path directly joining two nodes. There may be several parallel paths between two nodes.
Oriented Graph If directions of currents are marked in all the branches of a graph then it is called an oriented (or directed) graph .
CI
Connected graph A network graph is connected if there is a path between any two nodes .In our further discussion,let us assume that the graph is connected. Since, if it is not connected each disjoint part may be analysed separately as a connected graph. 1 2
TS
TU D
Node It is a point in the network at which two or more circuit elements are joined. In the graph shown 1, 2, 3 and 4 are nodes.
EN
4
CITSTUDENTS.IN
TS .IN
Graph 3
18
Network Analysis
10ES34
Unconnected graph If there is no path between any two nodes,then the graph is called an unconnected graph. 1 2 4 1 2 4 3 3 5 3 5 5
TS .IN
E E E D C C
Planar graph A planar graph is a graph drawn on a two dimensional plane so that no two branches intersect at point which is not a node. B C A B A D
Non planar graph A graph on a two dimensional plane such that two or more branches intersect at a point other than node on a graph.
CI
Graph
Co- tree A Co- tree is a set of branches which are removed so as to form a tree or in other words, a co- tree is a set of branches which when added to the tree gives the complete graph. Each branch so removed is called a link. Number of links = l = b (n-1) where b = Total number of branches n = Number of nodes
CITSTUDENTS.IN
TS
Tree of a graph Tree is a set of branches with all nodes not forming any loop or closed path. (*) Contains all the nodes of the given network or all the nodes of the graph (*) No closed path (*) Number of branches in a tree = n-1 , where n=number of nodes B C A B A 2 2 4 5 6 5 D
TU D
EN
Two possible trees
19
Network Analysis
10ES34
Complete Incidence matrix ( i )Complete incidence matrix:
An incidence matrix in which the summation of elements in any column in zero is called a complete incidence matrix.
TU D CI
Nodes A B C D Branches 1 -1 0 0 +1 2 +1 -1 0 0 3 +1 0 -1 0 4 0 -1 +1 0 5 0 +1 0 -1 6 0 0 +1 -1 CITSTUDENTS.IN
(*) There are four nodes A, B, C and D and six branches 1, 2, 3, 4, 5 and 6. Directions of currents are arbitrarily chosen. (*) The incidence matrix is formed by taking nodes as rows and branches as columns
TS
EN
Network
( ii )Reduced incidence matrix: The reduced incidence matrix is obtained from a complete incidence matrix by eliminating a row. Hence the summation of elements in any column is not zero. Example 1: Consider the following network and the oriented graph as shown
TS .IN
Reduced incidence matrix Oriented graph
Incidence Matrix Incidence matrix is a matrix representation to show which branches are connected to which nodes and what is their orientation in a given graph (*) The rows of the matrix represent the nodes and the columns represents the branches of the graph. (*) The elements of the incidence matrix will be +1, -1 or zero (*) If a branch is connected to a node and its orientation is away from the node the corresponding element is marked +1 (*) If a branch is connected to a node and its orientation is towards the node then the corresponding element is marked 1 (*) If a branch is not connected to a given node then the corresponding element is marked zero. Incidence Matrix
20
Network Analysis
10ES34
P =
-1 1 0 -1 0 0 1 0
1 0 -1 0
0 0 0 -1 1 0 1 0 1 0 -1 -1
PR =
-1 1 1 0 0 0 0 -1 0 -1 1 0 0 0 -1 1 0 1
Properties of a complete incidence matrix
Solution : The sum of each column of the given matrix is zero. Hence it is a compete incidence matrix.
Number of nodes = n = 4 ( say A. B. C and D) Number of branches = b = 6 ( say 1, 2, 3, 4, 5 and 6)
CI
Prepare a tabular column as shown. Nodes Branches 1 2 1 -1 0 0 0 1 -1 0
TS
A B C D
TU D
3 0 1 0 -1
Example 2 : The incidence matrix of a graph is as shown. Draw the corresponding graph.
EN
4 0 0 -1 1 5 1 0 0 -1
(*) Sum of the entries of each column is zero (*) Rank of the matrix is (n-1), where n is the no of nodes (*) Determinant of a loop of complete incidence matrix is always zero
1 0 0 0 1 -1 -1 1 1 0 0 0 0 -1 0 -1 0 1 0 0 -1 1 -1 0
From the tabular column, the entries have to be interpreted as follows: CITSTUDENTS.IN
TS .IN
6 -1 0 1 0
In the above example the fourth row is negative of sum of the first three rows. Hence the fourth can be eliminated as we know that it can be obtained by negative sum of first three rows. As a result of this we get the reduced incidence matrix.
21
Network Analysis
10ES34
From the first column the entries for A and B are ones . Hence branch 1 is connected between nodes A and B . Since for node A entry is +1 and for node B it is -1, the current leaves node A and enters node B and so on. From these interpretations the required graph is drawn as shown. 6 A B C 1 2 5 3 4 D
Example 3: The incidence matrix of a graph is as shown. Obtain the corresponding graph 1 1 0 0 0 0 -1 1 1 0 0 0 0 -1 1 0 0 0 0 0 0 0 1 -1 0 0 0 1
Nodes
TS
Branches 1 2 1 0 0 0 -1 3 1 -1 0 0 0 0 1 0 0 -1
TU D
4 0 1 -1 0 0 5 0 0 1 0 -1 E
Solution:- Given incidence matrix is a reduced incidence matrix as the sum of each column is not zero. Hence it is first converted in to a complete incidence matrix by adding the deleted row. The elements of each column of the new row is filled using the fact that sum of each column of a complete incidence matrix is zero. In the given matrix in first, third, fifth and the seventh column the sum is made zero by adding 1 in the new row and the corresponding node is E. The complete incidence matrix so obtained and also the graph for the matrix are as shown.
A B C D E
CI
Graph: CITSTUDENTS.IN
EN
6 0 0 1 -1 0 7 0 0 0 1 -1 6
TS .IN
22
Network Analysis
10ES34
Tie set Analysis:

In order to form a tree from a network several branches need to be removed so that the closed loops open up. All such removed branches are called links and they form a Co-tree. Alternatively when a link is replaced in a tree, it forms a closed loop along with few of the tree branches. A current can flow around this closed loop. The direction of the loop current is assumed to be the same as that of the current in the link. The tree branches and the link that form a loop is said to constitute a tie set.
A tie set is a set of branches contained in a loop such that the loop has at least one link and the remainder are twigs (tree branches) 6 6 z B
4 A
B 2
5 C A
EN
2 1 D Link 5 2 6
D Graph
tree (In thick lines) Co-tree (In dotted lines)
Tie set schedule Tie set 1 2 3
TS
We see that by replacing the links 1, 4 and 5 three loops are formed and hence three loop currents x, y and z flow as shown. The relationships obtained between loop currents, tree branches and links can be scheduled as follows
TU D
Tree branches 2, 3 1, 4 4, 5
CI
Tie set matrix (Bf) The Tie set schedule shown above can be arranged in the form of a matrix where in the loop currents constitute the rows and branches of the network constitute the columns Entries inside the matrix are filled by the following procedure :
CITSTUDENTS.IN
TS .IN
5 C x y 3 Loop current x y z
Definition
23
Network Analysis
10ES34
Let an element of the tie set matrix be denoted by mik Then 1 Branch K is in loop i and their current directions are same -1 If branch K is in loop i and their current directions are opposite. If the branch K is not in loop i mik =
By following this procedure we get the Tie set matrix which is shown below:
x y z
0 +1 0
+1 +1 0
+1 0 0
0 +1 +1 Or
+1 0 -1
0 0 -1
Bf =
Analysis of the net work based on Tie set schedule
From the tie set schedule we make the following observations.
(i) Column wise addition for each column gives the relation between branch and loop currents That is i3 i4 = x = y+ z i5 i6 i1 i2 = y = x+y
CI
i1 i2 i3 i5 i6
Putting the above equations in matrix form, we get 0 1 1 0 0 1 0 1 0 0 4 0 -1 0 -1 1 0 z 1 1 y
In compact form IB = B fT IL
CITSTUDENTS.IN
TS
TU D
= x-z = -z
EN
24
0 1 1 0 1 0 1 1 0 1 0 0 0 0 0 1 -1 -1
TS .IN
Loop Branches currentss 1 2
Network Analysis
10ES34
Where IB = Branch current matrix B fT = Transpose of the tie- set matrix IL = Loop current column matrix (ii)Row wise addition for each row gives the KVL equations for each fundamental loop Row - 1 Row - 2 Row - 3 : V1 + V2 + V3 : V1 + V2 + V4 : V4 - V5 - V6 = 0 = 0 = 0
V2 V3 V4 V6
= 0
V5
In compact form
B f VB
= 0
EN
5 50 V C 1 x 4 z 3 Branch Numbers 3 4 0 1 0 0 1 -1 5 y 6 2
Where VB = Branch voltage column matrix and B f = Tie - set matrix
TU D
D 2 0 1 0
Example: For the network shown in figure, write a Tie-set schedule and then find all the branch Currents and voltages
Solution: The graph and one possible tree is shown:
CI
Loop current x y z
TS
5 B 4 6 3
1 1 0 0
CITSTUDENTS.IN
TS .IN
- - - (1) A 5 10 B 10 5 5 D 5 -1 1 0 6 0 -1 1 25
V1 0 1 1 0 1 0 1 1 0 1 0 0 0 0 0 1 -1 -1
Network Analysis Tie set Matrix: Bf = 1 0 0 1 -1 0 1 0 0 1 -1 0 1 -1 0 1
10ES34
Branch Impedence matrix
ZB
= 0 0 0 0 0
ZL
20 -5 -10 -5 20 -5 -10 -5 20
TS
x y z 20x-5y-10z =50 -5x+20y-5z = 0 -10x-5y+20z =0
Loop Equations : 20 -5 -10 -5 20 -5 -10 -5 20
TU D
ZL IL = - Bf Vs =1 0 0 1 -1 0 0 1 0 0 1 -1 0 0 1 -1 0 1
CI
CITSTUDENTS.IN
Solving the equations, we get x = 4.17 Amps y = 1.17 Amps And z = 2.5 Amps
EN
-50 0 0 0 0 0
ZL =
1 0 0 1 -1 0 0 1 0 0 1 -1 0 0 1 -1 0 1
5 0 0 0 0 0 0 10 0 0 0 0 0 0 5 0 0 0 0 0 0 10 0 0 0 0 0 0 5 0 0 0 0 0 0 5
TS .IN
1 0 0 0 1 0 0 0 1 1 0 -1 -1 1 0 0 -1 1 26
5 0 0 0 0 0 10 0 0 0 0 0 5 0 0 0 0 0 10 0 0 0 0 0 5 0 0 0 0 0 5
Network Analysis
10ES34
Cut set Analysis

A cut set of a graph is a set of branches whose removal , cuts the connected graph in to two parts such that the replacement of any one branch of the cut set renders the two parts connected. A A 1 5 Example 4 B 3 D 4 B D 2 6 3 C C Directed graph Two separate graphs created by the cut set (1, 2, 5, 6)
Fundamental cut set is a cut set that contains only one tree branch and the others are links
Formation of Fundamental cut set
Example 1 : For the given graph write the cut set schedule A 1 B 2 C
TU D
5 D
EN
A 4
(*) Select a tree (*) Select a tree branch (*) Divide the graph in to two sets of nodes by drawing a dotted line through the selected tree branch and appropriate links while avoiding interruption with any other tree branches.
CI
Note that FCS - 1 yields node A and the set of nodes ( B, C, D) The Orientation of the fundamental cut set is usually assumed to be the same as the orientation of the tree branch in it, Which is shown by an arrow. By following the same procedure the FCS- 2 and FCS -3 are formed as shown below:
CITSTUDENTS.IN
TS
The fundamental cut set of the Selected tree is shown in figure
TS .IN
1 B 2 C 3 6 5 D
27
Network Analysis A 1 B 2 6 C FCS -2 C FCS -3 5 3 D 4 B 2 6 3 A 1
10ES34
It should be noted that for each tree branch there will be a fundamental cut set. For a graph having n number of nodes the number of twigs is (n-1).Therefore there will be (n-1) (n-1) fundamental cut-sets. Once the fundamental cut sets are identified and their orientations are fixed, it is possible to write a schedule, known as cut set schedule which gives the relation between tree branch voltages and all other branch voltages of the graph. Let the element of a cut set schedule be denoted by Qik then,
Qik = 1 If branch K is in cut set I and the direction of the current in the branch K is same as cut set direction . -1 If branch k is in cut set I and the direction of the current in k is opposite to the cut set direction. O If branch is k is not in cut set i
Cut set Schedule Tree branch 1 voltage e1 e2 e3
TU D
Branch Voltages 4 2 3 5 0 1 0 0 0 1 -1 1 0 -1 0 1 0 0 1 -1 1 0 -1 0 0 1 1 -1
TS
1 0 0 matrix. 1 0 Qf = 0 1 0 0
CI
CITSTUDENTS.IN
The elements of the cut set schedule may be written in the form of a matrix known as the cut set
EN
6 0 1 -1
TS .IN
28
Network Analysis
10ES34
Analysis of a network using cut set schedule (*) Column wise addition of the cut set schedule gives the relation between tree branch voltage and the branch voltages for the above cut the schedule V1 = e1 V2 = e2 V3 = e3 V4 = - e1 + e2 V5 = - e1+ e3 V6 = e2 - e3 In matrix form V1 V2 V3 V4 V5 V6 In compact form VB = QT f VT . (1) 1 0 0 = -1 -1 0 0 1 0 1 0 1 0 0 1 0 1 -1
e1 e2 e3
(*) Row wise addition given KCL at each node I1 - I4 - I5 = 0 0 I2 + I4 + I6 = I3 + I5 + I6 = 0 In matrix form
TS
1 0 0 1 0 0 0 -1 0 1 1 0
CI
TU D
-1 0 0 1 1 -1 I1 I2 I3 I4
Where VB =Branch voltage Matrix QTf = Transpose of cut set matrix and VT = Tree branch voltage matrix.
I5 I6 In compact form Qf IB = 0 (2) Where Qf = cut set matrix IB = Branch current matrix IK (*) Let us consider a network having b branches. Each of the branches has a representation as shown in figure VK YK
CITSTUDENTS.IN
EN
= 0
TS .IN
29
Network Analysis
10ES34
ISK Referring to the figure Ik = Yk Vk + Isk Since the network has b branches, one such equation could be written for every branch of the network ie I1 = Y1 V1 + Is1 I2 = Y2 V2 + Is2
-----------------------------
Putting the above set of equations in a matrix form we get IB = YB VB + Is
IB = Branch current matrix of order bx1 YB = Y1 0 0 0 0 - - 0 Y2 0 - - 0 - - - - 0 - - - Yb
Substituting (3) in (2) we get
TU D
Qf = = 0 0 (5)
.
VB = Branch Voltage column matrix of order bx1 and IB = Source current matrix of order bx1. YB VB + IS =
Qf YB VB + Qf IS =
But from (1) we have VB = Qf T VT Hence equation (4) becomes Qf YB Q f VT + Qf IS YC VT + QfIS

T
CI
or
Where YC = Qf YB Qf T is called cut - set admittance matrix Action Plan for cut set analysis. (*) Form the cut- set matrix Qf (*) Construct the branch admittance matrix YB (*) Obtain the cut set admittance matrix using the equation YC = Qf YB Qf T (*) Form the KCL or equilibrium equations using the relation YC VT = - Qf IS
CITSTUDENTS.IN
TS
YC VT = - Qf IS
EN
0 0 30
TS .IN
(3) = Branch admittance matrix of order bx b
Ib = Yb Vb + Isb
Network Analysis
10ES34
The elements of the source current matrix are positive if the directions of the branch current and the source connect attached to that branch are same otherwise negative. (*) The branch voltages are found using the matrix equation VB = Qf T VT (*) Finally the branch currents are found using the matrix equation IB = YB VB + IS
Fcs - 1 -Fcs - 2 -Fcs - 3 -Fcs - 4 --
( 1, 5, 6) (2, 6, ( 3, 7, (4, 5, 7) 8) 8)
EN
D FCS4 Branch 5 4 6 7 8 0 0 0 1 -1 0 0 1 1 -1 0 0 0 1 -1 0 0 0 1 -1 Qf = 1 0 0 0 0 1 0 0
TU D
2 3 0 1 0 0 0 0 1 0
Hence the cut set schedule is as follows: Tree branch 1 voltage e1 e2 e3 e4
CI
Hence the required cut set matrix
TS
1 0 0 0
0 0 -1 1 0 0 0 0 0 -1 1 0 1 0 0 0 -1 1 0 1 1 0 0 -1
CITSTUDENTS.IN
TS .IN
A FCS-1 1 4 E 2 B FCS2 FCS3 C
Example 2 : For the directed graph obtain the cut set matrix A 5 6 1 D E B 4 2 8 3 7 C Solution : The tree (marked by thick lines)and the link (marked by doffed lines)are as shown. The fundamental cut sets are formed at nodes A B C and D keeping E as reference node
31
Network Analysis
10ES34
Example 3: Find the branch voltages using the concept of cut-sets
1 1 1
1 1V
1 1
Solution : The voltage source is Transformed in to an equivalent current source. It should be noted that all the circuit Passive elements must be admittances and the net work should contain only current sources. The graph for the network is shown. A possible tree (shown with thick lines) and co tree (shown by dotted lines) are shown
FCS 1 =
3, 1, 5
EN
1mho 1A Branches 4 5 6 A FCS1
1
FCS 2 = 4, 2, 5 FCS 3 =
TU D
2 3 0 1 1 0 0 0 1 0 -1 1 0 0 0 1 -1
6, 1, 2
Cut set schedule Tree
TS
branch 1 voltage e3 e4 e6
CI
-1 0 1
Qf =
-1 0 1 0 -1 0 0 10 1 1 0 1 -1 0 0 0 1
CITSTUDENTS.IN
TS .IN
1mho 1mho 1 mho 1mho 1mho
5
3
FCS2
4 8
6 2
FCS3
32
Network Analysis 1 0 0 1 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 1
10ES34
YB =
-1 0 1
-1 0 1 0 -1 0 YC= 0 1 0 1 1 0 1 -1 0 0 0 1 1 0 0 0 0 0 0 1 0 0 0 0 0 0 10 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 1 0 -1 0 1 0 1 1 0 -1 0 0 0 1
3 = -1 -1
-1 3 -1
-1 -1 3
Equilibrium Equations
; YC VT = - Qf IS
3 -1 -1 -1 3 -1 -1 -1 3
TU D
e3 e4 e6 = -
3 e3 e4 e6 = - 1 -e3 + 3 e4 e6 = 0 - e3 e4 + 3e6 = 1
CI
Solving we get e3=-0.25 volt e4=0 e6=0.25 volt
CITSTUDENTS.IN
TS
EN
-1 0 1 0 -1 0 0 1 0 1 1 0 1 -1 0 0 0 1 -1 0 0 0 0 0 33
TS .IN
Network Analysis
10ES34
DUALITY CONCEPT
Two electrical networks are duals if the mesh equations that characterize one have the same mathematical form as the nodal equations of the other. Example 1 Consider an R-L-C series network excited by a voltage so source V as shown in the figure. The equation generating the circuit behavior is Ri+Ldi +1 idt =V ..(1) dt C Figure 1 Now consider the fed by a Current Source i is equation generating Circuit behavior is ..(2) parallel G-C-L network shown in the figure. The the GV+ CdV +1 vdt = i dt L
EN
Table of dual Quantities 1.Voltage Source 2.Loop currents 3.Iductances 4.Resistances 5.Capacitances 6. On KVL basis 7.Close of switch
CI
Note:Only planar networks have duals. Procedure for drawing dual network The duals of planar networks could be obtained by a graphical technique known as the dot method. The dot method has the following procedure.
Put a dot in each independent loop of the network. These dots correspond to independent nodes in the dual network.
CITSTUDENTS.IN
TS
TU D
Current source Node voltages Capacitances Conductances Inductances On KCL basis Opening of switch
Comparing the equations (1) and (2),we get the similarity between the networks of fig(1) and fig(2).The solution of equation (1) will be identical to the solution of equation (2) when the following exchanges are made R --- G, L--- C, C---L and V ---i Hence networks of figure (1) and (2) are dual to each other.
TS .IN
Figure 2
34
Network Analysis
10ES34
Put a dot outside the network. This dot corresponds to the reference node in the dual network. Connect all internal dots in the neighboring loops by dotted lines cutting the common branches. These branches that are cut by dashed lines will form the branches connecting the corresponding independent nodes in the dual network. Join all internal dots to the external dot by dashed lines cutting all external branches. Duals of these branches will form the branches connecting the independent nodes and the reference node.
Example 1:
3ohm 4F 2sin6t 4ohm 1 6H 2
CI
CITSTUDENTS.IN
Join node 1 and reference node through a dotted line passing through 3 ohms resistor. This element appears as 3mho conductance between node1 and reference node in the dual. Join node 2 and reference node through a dotted line passing through the capacitor of 4 Farads. This element will appear as 4 Henry inductor between node 2 and reference node in the dual Join node 2 and reference node through a dotted line passing through the resistor of 4 ohms. This element will appear as 4 mho conductance between node 2 and reference node. The Dual network drawn using these procedural steps is shown.
TS
TU D
Solution: Mark two independent nodes 1 and 2 and a reference node 0as shown in the figure. Join node 1 and 2 by a dotted line passing through the inductance of 6H.this element will appear as capacitor of 6 F between node 1 and 2 in the dual. Join node 1 and reference node through a dotted line passing the voltage source of 2sin6t volts. This will appear as a current source of 2sin6t amperes between node1 and reference node.
EN
TS .IN
Draw the exact dual of the electrical circuit shown in the figure.
35
Network Analysis
10ES34
CI
CITSTUDENTS.IN
TS
TU D
EN
36
TS .IN
Network Analysis
10ES34
1) Explain incidence matrix of a network of a network graph ? Give suitable example. 2) Define the following with suitable examples i) Planar and non-planar graph ii) Twigs and links 3) For the network shown in Fig. 8 write the graph of the network and obtain the tie-set schedule considering J1, J2, J5 as tree branches. Calculate all branch current.
4) Explain briefly trees, cotrees, and loops in a graph of network with suitable example 5) Explain with examples the principal of duality 6) Draw the oriented graph of the network shown in Fig. 10 select a tree, write the set schedule and obtain equilibrium equations
7) under what conditions do you consider topology for network analysis? For the graph shown in Fig. 3, for a co- tree (4,5,2,8), write tie set and cut set matrices. (10)
CI
CITSTUDENTS.IN
TS
TU D
EN
37
TS .IN
Network Analysis
10ES34
8) For the network shown in Fig. 4, draw its dual. Write in intergo differential form i) mesh equations for the given network ii) node equations for the dual.
V(t) = 10 sin 40t. 9) What are dual networks ? what is their significance ? Draw the dual of the circuit shown in fig. 8 .
CI
CITSTUDENTS.IN
TS
10) For the network shown in Fig. 5, perform source shifts, draw a graph, select tree with branches 1,2 and 3 and obtain tie set and matrices.
TU D
EN
38
TS .IN
Network Analysis
10ES34
Unit: 3 Network Theorems 1:
Syllabus of unit : Superposition, Reciprocit y and Millmans theorems Recommended readings:
1. Network Analysis, M. E. Van Valkenburg, PHI / Pearson Education 2. Networks Publications . and systems, Roy Choudhury, 2 edition, New Age International
3. Network theory ,
CI
CITSTUDENTS.IN
TS
TU D
Ganesh Rao.
EN
TS .IN
Hrs: 06
39
Network Analysis
10ES34
NETWORK THEOREMS
Mesh current or node voltage methods are general methods which are applicable to any network. A number of simultaneous equations are to be set up. Solving these equations, the response in all the branches of the network may be attained. But in many cases, we require the response in one branch or in a small part of the network. In such cases, we can use network theorems, which are the aides to simplify the analysis. To reduce the amount of work involved by considerable amount, as compared to mesh or nodal analysis. Let us discuss some of them.
SUPERPOSITION THEOREM:
The response of a linear network with a number of excitations applied simultaneously is equal to the sum of the responses of the network when each excitation is applied individually replacing all other excitations by their internal impedances. Here the excitation means an independent source. Initial voltage across a capacitor and the initial current in an inductor are also treated as independent sources. This theorem is applicable only to linear responses and therefore power is not subject to superposition. During replacing of sources, dependent sources are not to be replaced. Replacing an ideal voltage source is by short circuit and replacing an ideal current source is by open circuit. In any linear network containing a number of sources, the response (current in or voltage across an element) may be calculated by superposing all the individual responses caused by each independent source acting alone, with all other independent voltage sources replaced by short circuits and all other independent current sources replaced by open circuits. Initial capacitor voltages and initial inductor currents, if any, are to be treated as independent sources. To prove this theorem consider the network shown in fig.
TS
TU D
Ia IS ES
EN
IS
CI
We consider only one-voltage sources and only one current sources for simplicity. It is required to calculate Ia with Is acting alone the circuit becomes IS Z1 Z3 Ia1 = Z3 + Z4 Z1 + Z2 + Z3 Z4 Z3 + Z4 = IS Z1 Z3 (Z1 + Z2 + Z3) Z4 + (Z1 + Z2) Z3 ------------------------------------(1)
TS .IN
Ia1
CITSTUDENTS.IN
40
Network Analysis
10ES34
Ia2
ES
with ES acting alone Ia1 =
-E S Z4 + (Z1 + Z2) Z3 Z1 + Z2 + Z3
-ES (Z1 + Z2 + Z3) (Z1 + Z2 + Z3) Z4 + (Z1 + Z2) Z3
----------------------------------------(2)
Next converting the current source to voltage source, the loop equations
I2 =
Z1+Z2+Z3 -Z3 Z1+Z2+Z3 -Z3
From equation (1), (2) and (3) Ia1 + Ia2 = I2 = Ia Hence proof
CI
Reciprocity Theorem :
In an initially relaxed linear network containing one independent source only. The ratio of the response to the excitation is invariant to an interchange of the position of the excitation and the response. i.e if a single voltage source Ex in branch X produces a current response Iy the branch Y, then the removal of the voltage source from branch x and its insertion in branch Y will produce the current response Iy in branch X.
TS
ISZ1 Z3 - ES (Z 1+Z2+Z3) (Z1+Z2+Z3) Z4 + (Z1+Z2) Z3
TU D
IS Z1 -ES -Z3 Z3+Z4
EN
---------------------------------(3) 41
IS Z1
I1
I2
ES
CITSTUDENTS.IN
TS .IN
Network Analysis
10ES34
Similarly if the single current source Ix between nodes X and X produces the voltage response Vy between nodes Y and Y then the removal of the current source from X and X and its insertion between Y and Y will produce the voltage response Vy between the nodes X and X. Between the excitation and the response, one is voltage and other is current. It should be noted that after the source and response are interchanged, the current and the voltages in other parts of the network will not remain the same. Proof :
Z1 Z2 I1 A E _ Z3 Z4
Consider a network as shown in which the excitation is E and the response is I in Z4. The reading of the ammeter is
TU D
E
I1 =
Z1 + Z3 ( Z2 + Z4) Z2+Z3 +Z4
CI
I1 =
E
TS
E Z3
Z1 ( Z2+Z3+Z4) + Z3(Z2 + Z4)
Next interchange the source and ammeter.
EN
Z3
Z2+Z3 +Z4
TS .IN
(1)
42
CITSTUDENTS.IN
Network Analysis
10ES34
Z1
Z2
A Z3
Z4 + E _
I2
Now the reading of the Ammeter is :
I2 =
( Z2 + Z4) + Z1 Z3 Z1 + Z3
Z3
Z1+Z3
E Z3
I2 =
From (1) & (2)
CI
Transfer Impedance :
The transfer impedance between any two pairs of terminals of a linear passive network is the ratio of the voltage applied at one pair of terminals to the resulting current at the other pair of terminals . With this definition the reciprocity theorem can be stated as : Only one value of transfer impedance is associated with two pairs of terminals of a linear passive network .
TS
It can be similarly be shown for a network with current sources by writing node equations.
TU D
I1
=
Z1 ( Z2+Z3+Z4) + Z3(Z2 + Z4)
I2
EN
TS .IN
(2)
43
CITSTUDENTS.IN
Network Analysis
10ES34
I2 Z1 + E1
I2 Z1 I1_ Z2 Z2
c
+ E2
b d
w.r.t figs shown
E1 I2
E2 I1
ZT
If E1 = E2 then I1 = I2.
Millmans Theorem:
The single voltage is the ratio
Sum of the product of individual voltage sources and their series admittances Sum of all series admittances and the single series impedance is the reciprocal of sum of all series admittances.
TS
E1 E2
CI
TU D
Z1 Z2 E3 Z3 En Zn
Certain simple combinations of potential and current source equivalents are of use because they offer simplification in solutions of more extensive networks in which combinations occur. Millmans Theorem says that if a number of voltage sources with internal impedances are connected in parallel across two terminals, then the entire combination can be replaced by a single voltage source in series with single impedance.
EN
TS .IN
44
CITSTUDENTS.IN
Network Analysis
10ES34
Let E1, E2.En be the voltage sources and Z1, Z2Zn are their respective impedances. All these are connected between A & B with Y=1/Z, according to Millmans Theorem, the single voltage source that replaces all these between A & B is n EAB = EK YK
K=1
n YK
K=1
The single impedance is
Z =
1
K=1
n YK
Proof: Transform each voltage into its equivalent current source. Then the circuit is as in Fig. E1/Z1
TU D TS CI
B
With Y=1/Z the circuit is simplified as E1 Y1+E2 Y2 +..EnYn= EKYK A
Y1+ Y2 +..Yn= YK Which is a single current source in series with a single admittance Retransforming this into the equivalent voltage source
EN
Z1 E2/Z2 Z2 En/Zn Zn
TS .IN
A
And
CITSTUDENTS.IN
45
Network Analysis
10ES34
EY Y A +
Z= 1/Y B
The theorem can be stated as If a number of current sources with their parallel admittances are connected in series between terminals A and B, then they can be replaced by a single current source in parallel with a single admittance. The single current source is the ratio Sum of products of individual current sources and their impedances Sum of all shunt impedances
And the single shunt admittance is the reciprocal of the sum of all shunt impedances.
I1 A
I2
EN
+ I2/Y2 Y2
Let I1, I2, ..In be the n number of current sources and Y1,Y2..Yn be their respective shunt admittances connected in series between A & B. Then according to Millmans Theorem they can be replaced by single current I AB in parallel with a single admittance Y AB where IAB= IKZK ZK And YAB= 1 ZK In B Yn A
Transform each current source into its equivalent voltage source to get the circuit as in fig B + I1/Y1 + In/Yn I AB = I k Zk Z k
TU D
Y1 Y2 Y1 Z 1+Z2+..
CI
TS
I1Z1+I2Z2 +
Retransforming to equivalent current source
TS .IN
Yn YAB = 1 Zk
CITSTUDENTS.IN
46
Network Analysis
10ES34
1) Find the condition for maximum power transfer in the following network type AC source , complex source impedance and complex load impedance but only load resistance varying. 2)In the circuit shown in fig .10 find the load connected at AB for which the power transferred will be maximum . Also find maximum power
3) In the circuit shown in Fig. 11. Find Vx and prove reciprocity theorem.
4) ) Determine the current through 2 resister of the network shown in Fig. using superposition Principle
CI
TS
5) State Millmans theorem, using the same calculate current through the load in the circuit shown in Fig.
TU D
EN
TS .IN
47
CITSTUDENTS.IN
Network Analysis 7) Calculate the current I shown in fig. 19 using Millmans theorem
10ES34
8) state and explain i) Reciprocity theorem ii) Millmanns theorem. Using superposition theorem, obtain the response I for the network shown in Fig.12.
9) Use millmans theorem to determine the voltage Vs of the network shown in Fig.6 Given that ER = 230 00 V, EY = 230 -1200 V, and EB = 230 1200 V
CI
TS
TU D
EN
TS .IN
CITSTUDENTS.IN 48
Network Analysis
10ES34
Unit: 4 Network Theorems - II : Syllabus of unit :
2. Networks and systems, Roy Publications .
TU D
1. Network Analysis, M. E. Van Valkenburg, PHI / Pearson Education Choudhury, 2 edition, New Age International
CI
TS
EN
Thevinins and Nortons theorems; Maximum Power transfer theorem
TS .IN
Hrs: 06
49
CITSTUDENTS.IN
Network Analysis
10ES34
Thevinins and Nortons Theorems:

If we are interested in the solution of the current or voltage of a small part of the network, it is convenient from the computational point of view to simplify the network, except that small part in question, by a simple equivalent. This is achieved by Thevinins Theorem or Nortons theorem.
Thevinins Theorem :
.
M
To prove this theorem, consider the circuit shown in Fig.
CI
Z1 +
E1
TS
+
E2
TU D
N
Z2
ZL
CITSTUDENTS.IN
EN
Z4 + _ IS
Arrange the networks M and N such that N is the part of the network where response is required.
TS .IN
If two linear networks one M with passive elements and sources and the other N with passive elements only and there is no magnetic coupling between M and N, are connected together at terminals A and B, then with respect to terminals A and B, the network M can be replaced by an equivalent network comprising a single voltage source in series with a single impedance. The single voltage source is the open circuit voltage across the terminals A and B and single series impedance is the impedance of the network M as viewed from A and B with independent voltage sources short circuited and independent current sources open circuited. Dependent sources if any are to be retained.
50
Network Analysis
10ES34
Suppose the required response is the current IL in ZL. Connected between A and B. According to Thevinins theorem the following steps are involved to calculate IL Step 1: Remove ZL and measure the open circuit voltage across AB. This is also called as Thevinins voltage and is denoted as VTH
Z1 +
E1
Z2 A
. .
E2
Zs _
E1 I S Z S
VTH = VAB = E 1
Z1+Z 2 + Z S
Step 2:
TS
Z1 Z2 A + _ B
To obtain the single impedance as viewed from A and B, replace the network in Fig. replacing the sources. This single impedance is called Thevinins Impedance and is denoted by ZTH
CI
Z TH = Step 3 : CITSTUDENTS.IN
Z1 (Z 2 + Z S) Z1+Z 2 + Z S
TU D
Z1+Z 2 + Z S
ZS
VTH = VAB =
( E1 + E2) ( Z1+Z 2 + Z S ) ( E1 I S Z S ) Z1
EN
Z1 + E2
TS .IN
IS
51
Network Analysis Write the thevinins network and re introduce ZL

ZTH
10ES34
ZL
IL =
VTH ZTH + ZL
( E1 + E2) ( Z1+Z 2 + Z S ) ( E1 I SZ S ) Z1
CI
Z1+Z L Z1 CITSTUDENTS.IN
To verify the correctness of this, write loop equations for the network to find the current in ZL ( E1 + E2) ( E1 - IS Zs) Z1 Z1+Z 2 + Z S Z1 Z1+Z 2 + Z S
TS
TU D
Z1(Z 2 + Z S)
( E1 + E2) ( Z1+Z 2 + Z S ) ( E1 I SZ S ) Z1 + Z2 (Z1+Z 2 + Z S)
EN
Z1(Z 2 + Z S) Z1+Z 2 + Z S
Z1+Z 2 + Z S
TS .IN
+ ZL
52
Then the current in ZL is
Network Analysis ( E1 + E2) ( Z1+Z 2 + Z S ) ( E1 I SZ S ) Z1 (Z 1 + Z L) (Z1+Z 2 + Z S) Z1 2
10ES34
( E1 + E2) ( Z1+Z 2 + Z S ) ( E1 I SZ S ) Z1 Z1(Z 2 + Z S) + Z2 (Z1+Z 2 + Z S)
Z1 +
E1
Z2 +
I1
E2
ZL
I2
Z5 _
IS
The Thevinins equivalent consists of a voltage source and a series impedance . If the circuit is transformed to its equivalent current source, we get Nortons equivalent. Thus Nortons theorem is the dual of the Thevinins theorem.
The proof of the Nortons theorem is simple Consider the same network that is considered for the Thevinins Theorem and for the same response.
CI
E1 + E2 + CITSTUDENTS.IN
Step 1: Short the terminals A and B and measure the short circuit current in AB, this is Nortons current source. Z1 Z2 Zs
IN=Isc=E1+E2 + E2+ISZS
TS
TU D
If two linear networks, one M with passive elements and sources and the other N with passive elements only and with no magnetic coupling between M and N, are connected together at terminals A and B, Then with respect to terminals A and B, the network M can be replaced by a single current source in parallel with a single impedance. The single current source is the short circuit current in AB and the single impedance is the impedance of the network M as viewed from A and B with independent sources being replaced by their internal impedances
EN
TS .IN
53
Nortons Theorem :-
Network Analysis Z1 Z2+ZS =(E1 + E2)(Z2 + ZS )+(E2 +IS ZS )Z1 Z1 (Z2+ZS ) Step 2: This is the same as in the case of thevnins theorem Step 3: write the Nortons equivalent and reintroduce ZL A Zn Z
10ES34
B Then the current in ZL is
IL=IN. Zn Zn+ ZL (E1+E2)(Z2 +Zs)+(E2+IsZs)Z1 . Z1 (Z2 +Zs) Z1(Z2 +Zs) Z1 +Z2+Zs Z1(Z2 +Zs ) + ZL Z1 +Z2 +Zs (E1+E2)(Z2 +Zs)+(E2+IsZs)Z1 Z1 (Z2 +Zs) +ZL(Z1 +Z2+Zs )
Verification is to be done as in Thevinins Theorem
Since
CI
CITSTUDENTS.IN
TS
Determination of Thevinins or Nortons equivalent when dependent sources are present
IL=VTH =IN .ZTH Z TH +ZL Z TH +ZL
ZTH can also be determined as ZTH
When network contains both dependent and independent sources. It is convenient to determine ZTH by finding both the open circuit voltage and short circuit current If the network contains only dependent sources both VTH and IN are zero in the absence of independent sources. Then apply a constant voltage source (or resultant source) and the ratio of voltage to current gives the ZTH . However there cannot be an independent source ie, VTH or I N in the equivalent network.
TU D
(E1+E2) ( Z1 +Z2 +Zs) - (E1 -IsZs)Z1 Z1 (Z2 +Zs) + ZL (Z1+Z2+Zs)
EN
=VTH = o.c voltage across AB s.c current in AB IN 54
TS .IN
Network Analysis
10ES34
Maximum Transfer Theorem:When a linear network containing sources and passive elements is connected at terminals A and B to a passive linear network, maximum power is transferred to the passive network when its impedance becomes the complex conjugate of the Thevinins impedance of the source containing network as viewed form the terminals A and B. Fig represents a network with sources replaced by its Thevinins equivalent of source of ETH volts and impedance Zs, connected to a passive network of impedance z at terminals A & B. With Zs =Rs+JXs and z=R+JX, The proof of the theorem is as follows Current in the circuit is I= ETH (1) vf(Rs+R)2 +(Xs+X)2 Zs + ETh Z a
b power delivered to the load is P=I R

2
E2Th ( Rs+R)2 +(Xs+X)2
EN
.R oP =0 simultaneously oX =0 =0 (4)
As P = (R,X) and since P is maximum when dP=0 We have dP= oP .dR + oP .dX oR oX
TU D
CI
power is maximum when oP =0 and oR oP = (Rs+R)2+(Xs+X)2 R{2(Rs+R)} 2 oR D 2 ie, (Rs+R) +(Xs+X)2 2R{2(Rs+R)}
oP = R{2(Xs+X)} = 0 2 oX D ie 2R(Xs+X)=0 (5) From (5) we have X= -Xs (6) Substituting in (4) (Rs+R)2 =2R(Rs+R), ie, Rs+R= 2R ie , R=Rs
CITSTUDENTS.IN
TS
TS .IN
(2) (3)
55
Network Analysis Alternatively as P = E2R 2 2 (Rs+R) +(Xs+X) = E2Z Cose
10ES34
= ie P=f(Z,e)
e)2+(Xs+ZSine)2 E2Z Cose Zs2+Z2+2ZZsCos(e-es)

(Rs+ZCos
(7)
oZ for Pmax
2
oe
oP = 0 = {Zs +Z 2+2 Z Zs Cos( e-es)} Cos oZ 2 ie Zs +Z2=2 Z2+2Z Zs Cos( e-es). Or | Z |=| Zs | then with oe
e -Z Cos e {2Z+2Zs Cos( e-es)}
(Zs2+Z2 ) Sine =2Z Zs {Cose Sin (e-es )- Sine Cos(e-es)}
TU D
2
= - 2Z Zs Sines Substituting (8) in (9)
EN
oP = 0 = {Zs 2+Z 2+2 Z Zs Cos(e-es)}Z(-Sine)-ZCose {ZS2+Z 2 2Z Zs Sin(e-es)}
2 Zs Sine = -2 Zs Sines
e = -es
= Zs -
es
CI
Efficiency of Power Transfer: With Rs=RL and Xs= - XL Substituting in (1) P Lmax =E2THR = E2TH (2R) 2 4R and the power supplied is Ps = E2TH 2R = E2TH (2R)2 2R Then Ttra = PL = E2 TH 4R = 1 = 50% Ps E2TH 2R 2
CITSTUDENTS.IN
TS
TS .IN
(8) (9) 56
dP = oP .dZ + oP .de =0
Network Analysis
10ES34
This means to transmit maximum power to the load 50% power generated is the loss. Such a low efficiency cannot be permitted in power systems involving large blocks of power where RL is very large compared to Rs. Therefore constant voltage power systems are not designed to operate on the basis of maximum power transfer. However in communication systems the power to be handled is small as these systems are low current circuits. Thus impedance matching is considerable factor in communication networks. However between R & X if either R or X is restricted and between Z and restricted the conditions for Max P is stated as follows
8 if either |Z| or 8 is
CI
CITSTUDENTS.IN
TS
TU D
E2 2(Zs+Rs)
Case (iii):- If |Z| is varied keeping constant then from (8) |Z|=|Zs| Case (iv):- If |Z| is constant but is varied 2 2 Then from eqn (9) (Z +Zs ) Sin =-2Z Zs Sins Sin = -2ZZs Sin s 2 2 (Z +Zs ) Then power transfer to load may be calculated by substituting for R and X for specified condition. For example For case(ii) Pmax is given by Pmax = E2R (Rs+R)2+(Xs+X)2 = E2Zs = E2Zs 2 2 2 Rs +2RsZs+Zs2 +Xs2 (Rs+Zs) +Xs (ie Rs2+Xs2= Zs2)
EN
TS .IN
Case (i) :- R of Z is varied keeping X constant with R only Variable, conditions for max power transfer is (Rs+R)2+(Xs+X)2 2R(Rs+R)=0 2 2 2 2 Rs + R + 2RsR+(Xs+X) -2RsR-2R =0 2 2 2 R = Rs +(Xs+X) R= Rs 2 + (Xs + X) 2 Case (ii):- If Z contains only R ie, x=0 then from the eqn derived above 2 2 R=|Zs|. Rs + Xs
57
Network Analysis
10ES34
1) State and explain superposition theorem and Nortons theorem 2) Obtain the Thevenins equivalent of network shown in Fig. between terminals X and Y.
3) Obtain the Thevenins and Nortons equivalent circuits across terminals A and B for the circuit shown in Fig. 4.
4) ) In the circuit of Fig. 7 obtain I by Thevenins theorem
CI
CITSTUDENTS.IN
TS
TU D
EN
58
TS .IN
Network Analysis 5) state and prove Thevenins theorem
10ES34
6) Find Thevenins equivalent circuit across AB using Millmans theorem and find the current through the load (5+j5) shown in Fig. 8.
7) Calculate Thevenins equivalent circuit across AB for the network shown in fig. 9.
CI
CITSTUDENTS.IN
TS
TU D
EN
59
TS .IN
Network Analysis
10ES34
Unit: 5: Resonant Circuits:
Hrs: 06
Syllabus of unit : Series and parallel resonance, frequency response of series and Parallel circuits, Q factor, Bandwidth. Recommended readings:
2. Networks Publications .
and
systems,
EN
Roy Choudhury,
1. Network Analysis, M. E. Van Valkenburg, PHI / Pearson Education 2 edition,
CI
CITSTUDENTS.IN
TS
TU D
TS .IN
60
Network Analysis
10ES34
Resonant Circuits
Resonance is an important phenomenon which may occur in circuits containing both inductors and capacitors. In a two terminal electrical network containing at least one inductor and one capacitor, we define resonance as the condition, which exists when the input impedance of the network is purely resistive. In other words a network is in resonance when the voltage and current at the network in put terminals are in phase. Resonance condition is achieved either by keeping inductor and capacitor same and varying frequency or by keeping the frequency same and varying inductor and capacitor. Study of resonance is very useful in the area of communication. The ability of a radio receiver to select the correct frequency transmitted by a broad casting station and to eliminate frequencies from other stations is based on the principle of resonance. The resonance circuits can be classified in to two categories Series Resonance Circuits. Parallel Resonance Circuits. 1.Series Resonance Circuit
EN
We have XL and XC
TS
=27tfL = 1 27tfC
TU D
A series resonance circuit is one in which a coil and a capacitance are connected in series across an alternating I voltage of varying frequency as shown in figure. V The response I of the circuit is dependent on the impedance of the circuit, Where Z= R +jXL - jXC and I= V / z at any value of frequency
XL varies as f XC varies inversely as f
CI
In other words, by varying the frequency it is possible to reach a point where XL = XC . In that case Z = R and hence circuit will be under resonance. Hence the series A.C. circuit is to be under resonance, when inductive reactance of the circuit is equal to the capacitive reactance. The frequency at which the resonance occurs is called as resonant frequency ( fr) Expression for Resonant Frequency ( fr ) At resonance XL = XC
CITSTUDENTS.IN
TS .IN
R L C
61
Network Analysis Salient Features of Resonant circuit (*) At resonance XL = XC (*) At resonance Z = R i.e. impedance is minimum and hence I = V
10ES34
is maximum
Z (*) The current at resonance (Ir) is in phase with the voltage (*) The circuit power factor is unity (*) Voltage across the capacitor is equal and opposite to the voltage across the inductor.
Frequency response of a series resonance circuit For a R-L-C series circuit the current I is given by I=
R + j ( XL- XC ) At resonance XL = XC and hence the current at resonance (Ir) is given by Ir = V/R At off resonance frequencies since the impedance of the circuit increases the current in the circuit will reduce. At frequencies f Where f> fr , the impedance is going to be more inductive. Similarly at frequencies f < fr the circuit impedance is going to be more capacitive. Thus the resonance curve will be as shown in figure.
I Ir
TU D
Xc > Xl
TS CI
Qualify factor (or Q factor):
CITSTUDENTS.IN
EN
X l > Xc
fr
Another feature of a resonant circuit is the Q rise of voltage across the resonating elements. If V is the applied voltage across a series resonance circuit at resonance, I r = V R Any circuit response, which is frequency dependent, has certain limitations. The output response during limited band of frequencies only will be in the useful range. If the out put power is equal to
TS .IN
V
62
Network Analysis
10ES34
or more than half of the maximum powerout put that band of frequencies is considered to be the useful band. If I r is the maximum current at resonance then Power at resonance = Pmax = I2 r R Consider the frequency response characterstic of a series resonant circuit as shown in figure
Ir 0.707 Ir
F1
Fr
F2
Selectivity :
Selectivity is a useful characteristic of the resonant circuit. Selectivity is defined as the ratio of band width to resonant frequency Selectivity = f2- f1 fr It can be seen that selectivity is the reciprocal of Quality factor. Hence larger the value of Q Smaller will be the selectivity. The Selectivity of a resonant circuit depends on how sharp the out put is contained with in limited band of frequencies. The circuit is said to be highly selective if the resonance curve falls very sharply at off resonant frequencies.
CI
CITSTUDENTS.IN
TS
TU D
In the figure it is seen that there are two frequencies where the out put power is half of the maximum power. These frequencies are called as half power points f1 and f2 A frequency f1 which is below fr where power is half of maximum power is called as lower half power frequency (or lower cut off frequency). Similarly frequency f2 which is above fr is called upper half power frequency (or upper cut-off frequency) The band of frequencies between f2 and f1 are said to be useful band of frequencies since during these frequencies of operation the out put power in the circuit is more than half of the maximum power. Thus their band of frequencies is called as Bandwidth. i.e Band width =B.W = f2 - f1
EN
TS .IN
freq 63
Network Analysis
10ES34
Relation between Resonant frequency and cut-off frequencies Let fr be the resonant frequency of a series resonant circuit consisting of R,L and C elements .From the Characteristic it is seen that at both half frequencies f2 and f1 the out put current is 0.707 Io which means that the magnitude of the impedance is same at these points. At lower cut-off frequency f1 f1 Ir 0.707Ir
CI
Parallel Resonance
A parallel resonant circuit is one in which a coil and a capacitance are connected in parallel across a variable frequency A.C. Supply. The response of a parallel resonant circuit is somewhat different from that of a series resonant circuit.
Impedance at resonance We know that at resonance the susceptive part of the admittance is zero. Hence Y0 = R 2 R +m0 2 L 2
CITSTUDENTS.IN
TS
TU D
V, f Hz
EN
0.707Ir
Resonance by varying Inductance Resonance in RLC series circuit can also be obtained by varying resonating circuit elements . Let us consider a circuit where in inductance is varied as shown in figure. R L C Ir
TS .IN
fr
f2
64
Network Analysis But R2 +m0 2 L

2
10ES34 = L/C
So Y0 = RC/L or Zo = L/RC Where Zo is called the dynamic resistance. when coil resistance R is small, dynamic resistance of the parallel circuit becomes high. Hence the current at resonance is minimum. Hence this type of circuit is called rejector circuit.
Frequency response characterisitics

The frequency response curve of a parallel resonant circuit is as shown in the figure. We find that current is minimum at resonance. The half power points are given by the points at which the current is vf2 Ir .From the above characteristic it is clear that the characteristic is exactly opposite to that of series resonant. I
2Ir
Frequency
TU D
Ir f1 = V / ( 1/ 0C ) V / Z0 = Z00C = (L / RC) 0 C = 0L / R
Quality factor ( Q-factor) The quality factor of a parallel resonant circuit is defined as the current magnification
CI
Hence the expression for the Q- factor for both series and parallel resonant circuit are the same Also Band width= f0 / Q
CITSTUDENTS.IN
TS
Q = Current through capacitance at resonance Total Current at resonance = IC0 / I0
EN
fr f2 65
TS .IN
Network Analysis
10ES34
II A coil and a Practical Capacitor in parallel IL Consider a parallel resonant circuit in which the resistance of the capacitance is also considered Impedance of the coil = ZL = RL + j L YL = 1 / ZL = 1/ RL+j L = RL j L / RL2 +2 L2 Impedance of the Capacitor = ZC = RC j / C = RC + j / C Rc2 +1/2C2 Therefore total admittance = Y=YL+YC RL IC XL
=( RL j L / RL2 +2L2)+ RC + j / C
TS
CI
At Resonance the admittance is purely conductive given by
CITSTUDENTS.IN
TU D
20 = 1/LC(R L2 L/C ) ( RC 2 L/C) 0 = 1/vf LC f0 = 1 2 -J LC
At resonance the susceptance part of the total admittance is zero, which gives 0L 1/0C = RC 2 + 1/ 20C 2 RL2 +2 0L2 1/LC [ RL2 +2 0L2] = 20[ RC2 + 1/2 0C2 ] 20 ( RC2 L/C ) = RL2 / LC 1/ C2
RL 2 L/C vf ( RC 2 L/C) ( R L2 L/C) ( R C2 L/C)
EN
TS .IN
V Rc2 +1/2C2 66
RC
XC
Network Analysis
10ES34
Y0 =
RL + RL2 +2 0L2
RC RC2 + 1/2 0C2
Solution: Let ZL be the impedance of the inductive branch then ZL = 10+ j 10 YL = 1/ (10 +j 10) = 10 j 10 = 10- j 20 102 +102 200
TS .IN
-j2 RC j 2 RC2 + 4 25
Example 1 : Determine the value of RC in the Shown in figure to yield Resonance
RC
10
YC =
RC j 2
TU D
Total admittance of the circuit = Y = YL + YC
For the circuit under Resonance the Susceptance part is zero ( 2/ RC 2 + 4) - (10 / 200) = 0
2 RC = 36 RC = 6 ohms
EN
= Answer R L2 R2
2
Let ZC be the impedance of the capacitive branch then ZC = RC j 2
j10
CI
TS
25 mH
Example 2: An Impedance coil of 25 ohms Resistance and 25 mH inductance is connected in parallel with a variable capacitor. For what value of Capacitor will the circuit resonate.If 90 volts,400 Hz source is used, what will be the line Current under these conditions Solution: 0 = 2f0 = 2( 400)
2
90 Volts,400Hz
= 1 LC 6.316 x 106 = 1 -
m0
CITSTUDENTS.IN
67
Network Analysis LC L
2
10ES34
1 LC
= m0 2 + R2 L2 = 6.316 x 106 + 252 / (25 x 10-3)2 = 7.316 x 106 C= 5.467 F
I0 = V0/ Z0 = 90/ 182.89 = 0.492 ampere
CI
CITSTUDENTS.IN
TS
TU D
EN
68
TS .IN
Z0 = L/RC = (25 x 10-3)/ 25 x 5.467 x 10-6 = 182.89 ohms
Network Analysis
10ES34
1) Explain parallel resonance ? Derive the condition for parallel resonance when RL connected parallel to RC . 2) Show that resonant frequency of series resonance circuit is equal to the geometric mean of two half power frequencies. 3) In the circuit given below in Fig. 21, an inductance of 0.1 H having a Q of 5 is in parallel with a capacitor. Determine the value of capacitance and coil resistance at resonant frequency of 500 rad/sac.
4) In the circuit shown in Fig. 22, determine the complete solution for the current when the switch S is closed at t = 0. Applied voltage is V (t) = 400 cos 500+ Resistance R = 15, inductance L = 0.2H and capacitance C = 3 F.
5) In the circuit shown in fig. 23 the switch S is moved from a to b at t = 0. Find values of i,
CI
6) A series resonant circuit includes 1 11F capacitor and a resistance of 16? If the band Width is a 500 rad/sec, determine i) ii) Q and iii) L 7) A two branch antiresonant circuit contains L = 0.4H and C = 4011F. Resonance is to be achieved by variation of RL and RC. Calculate the resonance frequency for the following cases: i) RL = 120, RC = 80 CITSTUDENTS.IN
TS
at t = 0+ if R = 1, L = 1H, c= 0.1 F and V=100 V.
Assume steadily state is achieved when K is at a.
TU D
EN
69
TS .IN
Network Analysis
ii) iii) RL = 80Q, Rc = 0 RL = Rc = lOOQ
10ES34
CI
CITSTUDENTS.IN
TS
TU D
EN
70
TS .IN
Network Analysis
10ES34
Unit: 6
Transient behavior and initial conditions
Hrs: 07
Syllabus of unit : Behavior of circuit elements under switching condition and their Representation, evaluation of initial and final conditions in RL, RC and RLC circuits for AC and DC excitations. Recommended readings:
1. Network Analysis, M. E. Van Valkenburg, PHI / Pearson Education
CI
CITSTUDENTS.IN
TS
TU D
EN
2. Networks Publications .
and
systems,
Roy
Choudhury,
TS .IN
2 edition,
71
Network Analysis
10ES34
R-L Series circuit transient:
Consider The R-L series circuit shown in the fig. Switch K is closed at t=0. Referring to the circuit, balance equation using ldi(t ) V (t ) = R i(t ) + dt Kirchoffs law can be written as Taking Laplace Transform we get V (s) = I(s) R + L{SI(s) i(0 )} s Assuming there is no stored energy in the inductor I(0)=0 V (s) = RI(s) + LSI(s) s r 1 V (s) 1 V (s) I(s) = = L R\ ( S(R + SL) S S+ 1 L) J l \ B A I(s) = + R S S+ L V (s) R\ ( A S + 1 + BS = L L) \ ( R \ V (s) A 1= L \L) Put s=0
EN
CI
CITSTUDENTS.IN
TS
TU D
TS .IN
R L K t=0 i(t) V
Electrical circuits are connected to supply by closing the switch and disconnected from the supply by opening the switch. This switching operation will change the current and voltage in the device. A purely resistive device will allow instantaneous change in current and voltage. An inductive device will not allow sudden change in current or delay the change in current. A capacitive device will not allow sudden change in voltage or delay the change in voltage. Hence when switching operation is performed in inductive or capacitive device the current and voltage in the device will take a certain time to change from preswitching value to steady value after switching. This study of switching condition in network is called transient analysis. The state (or condition) of the current from the instant of switching to attainment of steady state is called transient state or transient. The current and voltage of circuit elements during transient period is called transient response. The transient may also occur due to variation in circuit elements. Transient analysis is an useful tool in electrical engineering for analysis of switching conditions in Circuit breakers, Relays, Generators etc. It is also useful for the analysis of faulty conditions in electrical devices. Transient analysis is also useful for analyzing switching Conditions in analog and digital Electronic devices.
72
Network Analysis V (s) R S= put B= V (s) R R L B ( R\ V (s) 1 = L ) \ L
10ES34
A=
1t l VI i(t ) = 1 e \ L ) R L J
(R \
The equation clearly indicates transient nature of current, which is also shown in figure. L = Where R Tune constant of the circuit, which is denoted by Z given in seconds.
Hence
CI
CITSTUDENTS.IN
V V Putting t=z we get i(z) = 0.632 R Where R = steady state current. Hence Time constant for an R-L series current circuit is defined as the time taken by the circuit to reach 63.2% of its final steady value.
R-C series circuit Transient
TS
J
i(t ) =
VI 1 e R L
TU D
Z l t
EN
73
TS .IN
I l 1 V( s) 1 I(s) = R S S+R L LJ Therefore Taking inverse Laplace we get
Network Analysis Consider the RC circuit shown. Let the switch be closed at t=0. Writing the balance equation using Kirchoffs voltage law , 1 v (t ) = iR + J i dt c Taking Laplace transform, we get V (s) 1 I I(s) Q 0 l = I(s )R + + s J S cL s Let us assume that there is no stored energy in the circuit. + Hence Q o =0
10ES34
( )
( )
( \ 1 1 V (s) 1 I(s) = R S+ 1 1 1 RC ) \ Taking Laplace inverse we get

1t i(t ) = V (t ) e \ RC ) R ( 1 \
CI
CITSTUDENTS.IN
1 = the time constant of the circuit. The sketch of transient current is shown in figure Where RC 1 = RC in the current equation we get Putting V i(z) = 0.367 R Hence time constant of RC series current can be defined as the time taken by current transient to fall to 36.7% of its initial value.
TS
TU D
EN
74
TS .IN
I(s) 1 1 V (s) r = I(s)R + = I(s) R + CS CS J s l
Network Analysis Example 1:
10ES34
CI
CITSTUDENTS.IN
TS
When the circuit is switched to position 2, this 1 Amp current constituted the stored energy in the coil. di 20i + 4 = 0 Writing the balance equation for position 2 we get dt Taking Laplace transformation 20I(s) + 4[s I(s) i(0 )] = 0 20I(s) + 4[s I(s) 1] 1 4 I(s) = = 4(s + 5 ) s + 5 taking inverse Laplace we get i(t ) = e 5t
TU D
EN
TS .IN
In the circuit shown in figure the switch K is moved from position 1 to position 2 at time t = 0. The steady state current having been previously established in R-L circuit. Find the current i(t) after switching. Solution: From the given data the circuit is under steady state when switch K is in position 1 under steady 10 state condition inductance is a short and hence i(0) = 10 = 1 Amp.
75
10ES34
CI
CITSTUDENTS.IN
TS
A series R-C circuit is shown in figure. The capacitor has an initial charge of 800 Coulombs on its plates, at the time the switch is closed. Find the resulting current transient. 6 Solution: From the data given q(0) = 800 10 C Writing the balance equation we get 1 100 = 10i(t ) + 4 10 6 J i(t)dt Taking Laplace transformation 100 1 [I(s) Q(0)] = 10I(s) + S 4 10 6 S I 10 6 l 100 800 10 6 I(s) 10 + = + 4S J S 4 10 6 S L 100 + 200 = 5 r 40S + 106 1 30 = I(s) 4S J S l 1200 1200 = I(s) = 6 ( 40S + 10 10 6 \ 1 40 S + 1 40 ) \ 30 I(s) = S + 25000 Taking Inverse Laplace we get i(t) = 30e 25000t
TU D
EN
TS .IN
76
Network Analysis
10ES34
CI
t L
V(s) = RI(S) + LS[I(S) i(0)] S Since there is no mention of initial current in the coil i(0) =0 10 = I(s) + I(s)LS Hence S 10 I(S){SL + 1} = S 10 A B 10 L = = + I(s) = 1\ S ( 1\ ( S(1 + SL ) S S+ 1 S+ 1 L) L) \ \ 1\ 10 ( = A S + 1 + BS L L) \ A=10 B= -10 I(S) = 10 10 1 S+ L Taking Inverse Laplace we get
i(t) = 10 10e The relay operates at t = 0.347 seconds when the current value reaches 5A. Hence 5 = 10
0.347 10e L 0.347 10e L 0.347 =5 e L
Solving the equation we get L=0.5H
CITSTUDENTS.IN
TS
= 10 5 = 5
TU D
EN
77
TS .IN
Example3: For the circuit shown in figure the relay coil is adjusted to operate at a current of 5 Amps. Switch K is closed at t = 0 and the relay is found to operate at t = 0.347 seconds. Find the value of inductance L of the relay. Soln: Writing the balance equation for the relay circuit di V(t) = Ri(t) + L dt Applying Laplace transformation
10ES34
In figure the switch K is closed. Find the time when the current in the circuitry reaches to 500 mA Soln: When the switch is closed Vc (0) = 0 When the switch is closed at t = 0
I1 (t)50 = 10 I2 (t) 70 + 1 = 10 100 10 6 J i2dt
Taking Laplace for both the equations I1(S) = 10 = 0.2 (1) 5 50S 1 I (s) 10 I2 (S) 70 + 2 = c S 5 I2 (S) 10 70I2 (s) + = 6 100 10 s 5 1 10 1 1 I2(S) = (2) = ' = 4 3 7 S + 142.86 70S + 10 7s + 10 Taking inverse Laplace for equation (1) and (2) I1 (t) =0.2 A 1 142.86t I2 (t) = e 7 Total current from the battery i(t) =I1 + I2 1 i(t) = 0.2 + e 142.86t 7 when this current reaches 500 mA 1 500 10 3 = 0.2 + e 142.86t 7 Solving we get t = 5.19 10-3 Seconds.
CI
CITSTUDENTS.IN
TS
TU D
EN
78
TS .IN
Network Analysis R-L-C Series Transient circuit:
10ES34
Roots of the characteristic equation are given by
1 R (R\ S1,S2 = 1 LC 2L \ 2L )
CI
CITSTUDENTS.IN
Intial conditions:
The reason for studying initial and final conditions in a network is to evaluate the arbitrary constants that appear in the general solution of the differential equations written for the network. In this chapter we concentrate on finding the change in selected variables in a circuit when a switch is thrown from open to closed or vice versa position. Please note that t = 0 indicates the time of throwing the switch t = 0- indicates time immediately before throwing the switch and
TS
2
R 1 ( R\ 1 4 LC \L) S1,S2 = L 2
TU D
2
Assuming zero initial conditions when switch K is closed the balanced equation is given by di 1 V = iR + L + J idt dt C Taking Laplace transformation we get I(s) V(s) = 1(s)R + LSI(s) + CS s 1 l I = I(s) R + SL + CS J L V(s) V(s) L I(s) = = R 1 1 2 S(R + SL + ) S + S+ L LC CS The time response of the circuit depends on the poles or roots of the characteristic equation R 1 =0 S2 + S + L LC
EN
TS .IN
79
Network Analysis
10ES34
t =0+ indicates time immediately after throwing the switch. We are very much interested in the change in currents and voltages of energy storage elements (inductor and capacitor) after the switch is thrown since these variables along with the sources will dictate the circuit behavior for t > 0. Initial conditions in a network depend on the past history of the circuit (before t= 0-) and structure of the network at t = 0+.Past history will show up in the form of capacitor voltages and inductor currents. Initial and final conditions in elements
The inductor : Initial condition The switch is closed at t= 0
CI
t The expression for current through the inductor is given by i(t) = 1 v dt L -oo 0t = 1/L vdt + 1/L vdt -oo t 0= i(0-) + 1/L vdt 0Putting t = 0+ 0+ i (0+) = i (0-) + 1/L vdz 0i (0+) = i (0-) The above equation indicates that the current in an inductor can not change instantaneously. Hence if i (0-) =0, then i(0+) = 0. This means that at t = 0+ inductor will act as an open circuit, independent of voltage across the terminals.
TS
TU D
L
EN
V
If i (0-) = I0 (i. e. if a residual current is present) then i (0+) = I0 , meaning that an inductor at t = 0+ can be thought of as a current source of I0 which is as shown
CITSTUDENTS.IN
TS .IN
K L O.C
The resistor: The cause effect relation for the ideal resistor is given by v = Ri. From this equation we find that the current through a resistor will change instantaneously, if the voltage changes instantaneously.Similarly voltage will change instantaneously if current changes instantaneously.
80
Network Analysis
10ES34
I0 L Final (or steady state) condition
II I0
The final condition equivalent circuit of an inductor is derived from the basic relation ship V = L di/ dt Under steady state condition di = 0 which means v = o and hence L acts as a short S.C
The capacitor
CI
The switch is closed at t = 0 . The expression At t=0 For voltage across the capacitor is given by C t i(t) v v = 1/ C i dt -oo 0t v(t) = 1/ C i dt + 1/ C i dt 0-oo Putting t= 0+ 0+ v(0+ ) = v(0-) + 1/C i dt 0V(0+) = V (0-) which means that the voltage across the capacitor can not change instantaneously. If V(o-) = o then V (o+) = o indicating that the Capacitor acts as a short at t=0+
TS
C V0= Q0 / C
TU D
Final (or steady state ) condition
CITSTUDENTS.IN
EN
TS .IN
S.C I0 At t= oo S.C at t=0+ -+ V0 81
at t = oo ( final or steady state) I0
Network Analysis
10ES34
The final-condition equivalent network is determined from the basic relationship i = C dv/dt Under steady state condition dv / dt = 0 which means at t= oo the Capacitor acts as a open circuit. C O.C V0 + V0 -+ O.C
CI
CITSTUDENTS.IN
TS
TU D
EN
82
TS .IN
Network Analysis
10ES34
1) Establish the procedure for evaluating initial conditions with suitable examples. 2) ) In the circuit shown in Fig. 20 V=10V, R= 10, L=1H, C= 10F, and VC=0 . find i(0+), (0+) and (0+) it switch K is closed at t=0.
3) ) Find i(t) for the following network shown in Fig. 21 if if the switch K is opened at t= 0, before that the circuit has attained steady state condition .
4) R = 1, L = 1H and C = 1/2F are in series with a switch across C 2V is applied to the circuit. At t = 0 the switch is in closed position. At t = 0 the switch is opened. Find at t = 0+ , the voltage across the switch, its first and second derivatives. 5) A coil of R = 1000 and L = 1 H is connected to a d.c. voltage of 100V through a changeover switch. At t = , the switch connects a capacitor of C = 0.1 F in series with the coil, excluding the voltage. Solve for i, and in the coil all at t = 0+.
i) F(s) =
CI
iii) F(s) = CITSTUDENTS.IN
ii) F(s) =
7) Why do we need to study initial condition? Write the equivalent from of the elements in terms of the initial condition of the element
TS
6) Use initial and final value theorems, where they apply, to find f(0) and f( ) for the following :
TU D
EN
83
TS .IN
Network Analysis
10ES34
8) A parallel R-L circuit is energized by a current source of 1 A. the switch across the source is opened at t=0. Solve for V, Dv and D2v all at t=0+ if R=100 and L=1H. 9) Determine the Thevenins equivalent Vab(S) and Zab(S) for the network on Fig.12 for zero initial conditions.
10) For the circuit shown in Fig. 15 the switch is opened at t=0. If L = G=1mho, C =1F and V=1v, find the node voltages v1(t) and v2(t)
CI
CITSTUDENTS.IN
TS
TU D
EN
84
TS .IN
H,
Network Analysis
10ES34
Unit: 7 Laplace Transformation & Applications : Syllabus of unit

Solution of
Hrs: 07
CI
CITSTUDENTS.IN
TS
TU D
EN
85
TS .IN
networks, step, ramp and impulse responses, waveform Synthesis
Network Analysis
10ES34
LAPLACE TRANSFORMATION:
Laplace transform is a very useful and powerful tool in circuit analysis.Integro-differential equations Can be transformed in to algebraic equations using the technique of Laplace transformation and complete solution involviong both natural response and forced response is obtained in one step Definition of Laplace Transform : Let f(t) be a function of time.Assuming the value of function to be zero for t<0,the Laplactransform of f(t) is given as oo L [ f(t) ] = F(S) = f(t) e-St dt 0 f(t) is a function in time-domain and F(S) is a function in complex frequency domain. Complex frequency S is given by S= +j From the above it is obvious that Laplace transformation changes a function in time domain into a function in frequency domain. Important properties of Laplace transform Linearity Property: If L { f1(t) }= F1(S) And L{ f2(t) }=F2(S)
Time-Shifting Property:
TS
TU D
Then L {a1 f1(t) }+ a2 f2(t)}= a1 F1(S)+ a2 F2(S) oo Proof: L {a1 f1(t) }+ a2 f2(t)}= {a1 f1(t) }+ a2 f2(t) }e-St dt 0 oo oo = a1 f1(t) e-St dt +a2 f2(t) e-St dt 0 = a1 F1(S) + a2 F2 (S)
CI
If L{ x(t) } = X(S) then for any real number t0 L{ x(t- t0) u(t- t0)}= e-to S X(S) t = to time
oo Proof: Let L{ x(t-to) u(t- to) } = x(t- t0) u(t- t0)}e-St dt 0 Since u(t- to)= 1 }t>t0 0 }t<t0 oo
CITSTUDENTS.IN
EN
u(t- to)
TS .IN
86
Network Analysis We get L [ x(t-t0) u(t-to)] = x(t- t0)e-St dt to Let t=t0 + T dt = dT As t t0 T 0 T oo As t oo oo Hence we get L { x(t-t0) u(t-to)}= x(T) e-S (T + t0) dT oo 0 = e-Sto x(T) e-S T dT 0 = X( S) e-Sto
10ES34
Frequency-domain shifting property If L{x(t)}= X(S) then L{eSot x(t) }= X(S-So) oo Proof: L{eSot x(t) }= eSot x(t) e-St dt 0 oo = x(t) e-( S-So)t 0 = X( S- S0)
If L[ x(t) ] = X(S) then
Proof:
CI
CITSTUDENTS.IN
L [ x(at) ] = 1/a X( S/a) oo L [ x(at) ] = x(at) e-St dt 0 Put at= T oo a dt = d T Hence L [ x(at) ] = 1/a x(T) e- ST / a d T 0 oo Hence L [ x(at) ] = 1/a x(T) e- ST / a d T 0 L [ x(at) ] = 1/ a X( S/ a)
TS
TU D
4. Time-Scaling Property
EN
87
TS .IN
Network Analysis 5. Time-Differentiation Property If L[ x(t) ] = X(S) L[dx/dt] = S X(S) x(0) Proof: Let y(t) = dx/dt oo Then L[ y(t)] = Y(S) = y(t) e-St dt 0 oo = (dx/dt) e-St dt 0 oo oo = [ e-st x(t) ] x(t) { -se-St}dt oo 0 0 = [ x(oo) x(0) ] + s x(t) e-St dt 0 Y(S)= SX(S) x(0) i.e. L[dx/dt] = S X(S) x(0)
10ES34
6.Time-integration Property For a Causal signal x(t) , if y(t) =
Proof
CI
CITSTUDENTS.IN
TS
oo x(T) d T Where T is a dummy variable of t ' 0 Then L[ y(t)] =Y(S) = X(S) S oo L{ x(t) }= X(S) = x(t) e-St dt 0 Dividing both sides by S yields oo X(S)= x(t) e-St dt oo oo S 0 Soo = e-St x(t)dt [ x(t) e-St(-s) dt] S 0 0 S oo = e-St y(t) - y(t) e-St (-s) dt S 0 S = e-St y(t) - Y(S) S X(s)= Y(S) S
TU D
Therefore Y(S) = X(S) S
EN
as e-St y(t) =0 at t=oo S
TS .IN
88
Network Analysis 7. Time-Periodicity Property
10ES34
x(t)
time T x1(t) 2T 3T 4T
0 x2(t)
T x3(t)
2T
CI
CITSTUDENTS.IN
TS
Let us consider a Function x(t) that is periodic as shown in figure.The function x(t) can be represented as the sum of time-shifted functions as shown in figure. Hence x(t) = x1(t) + x2(t) + x3(t) + Where x2(t) = x1(t- T) u(t-T) x3(t) = x1(t- 2T) u(t-2T) and so on Hence x(t) = x1(t) + x1(t- T) u(t-T)+ x1(t- 2T) u(t-2T) + .. Where x1(t) is the waveform described over the first period of x(t). Taking Laplace transformation on both sides of the above equation we get X(s) = X1(s) + X1(s) e-TS + X1(s) e-2TS + X1(s) e-3TS +
TU D
EN
2T 3T 89
TS .IN
Network Analysis = X1(s)[1+ e-TS + e-2TS +e-3TS + ] But 1+ a2 +a3 + a4 + ..= 1 1-a Hence we get X(S) = X1(S) 1 1- e-TS For a< 1
10ES34
Initial value Theorem:

The Initial -value theorem allows us to find the initial value x(0) directly from the Laplace Transform X(S).If x (t) is a casual signal, then x(0) = Lim S X(S) S oo Proof: WE have L dx(t) = S X(S) x(0) dt oo (dx/dt) e-St dt = S X(S) x(0) 0 oo ,we get Taking Limit on both sides as S oo Lim (dx/dt) e-St dt = Lim S X(S) x(0) oo 0 S oo S Hence 0 = Lim S X(S) -x(0) oo S Final Value theorem
The final value theorem allows us to find the value of x(oo) directly from its Laplace Transformation X(S) If x(t) is a casual signal, Lim x(t) =Lim S X(S) oo S 0 t Proof: We have L dx(t) = S X(S) x(0) dt oo (dx/dt) e-St dt = S X(S) x(0) 0 Taking the limits S 0 on both sides we get,
CI
CITSTUDENTS.IN
TS
TU D
oo
or Lim S X(S) = x(0) S oo
EN
90
TS .IN
Network Analysis Lim [ S X(S) -x(t)] = Lim (dx/dt) e-St dt S 0 S 0 oo 0 (dx/dt) Lim e-St dt S 0 = S X(S) x(0)
10ES34
oo = (dx/dt) dt = 0
oo x(t) 0
x(oo) = Lim S X(S) S 0
Inverse Laplace Transformation:
CI
CITSTUDENTS.IN
The function X(S)as defined by equation(2) is said to be rational function of S,since It is a ratio of two polynomials.The denominator Q(S) can be factored in to linear factors. A partial fraction expansion allows a strictly proper rational function P(S) to be expressed Q(S) As a factor of terms whose numerators are constants and whose denominator corresponds to Linear or a combination of linear and repeated factors.This in turn allows us to relate such terms To their corresponding inverse Laplace transform. For performing partial fraction technique on X(S) the function X(S) has to meet the following conditions. i) X(S) must be a proper fraction i.e. m< n . When X(S) is improper we can use long division
TS
Partial Fraction method: In many situations,the Laplace transform can be expressed in the form X(S) = P(S) (2) Q(S) Where P(S)= bmSm + bm-1Sm-1+ bm-2Sm-2 ..+ b0 Q(S)= an Sn + an-1 Sn-1 + an-2 Sn-2 +..+ a0
TU D
The inverse Laplace Transform of X(S) is defined by an integral operation with respect to Variable S as follows + oo x (t) = 1/ 2 X(S) eSt ds (1) - oo Since S is a complex quantity the solution requires a knowledge of complex variables.In Other words the evaluation of integral in equation (1) requires the use of contour integration In the complex plane, which is very difficult.Hence we will avoid using equation(1) to compute Inverse Laplace transform.We go for indirect methods to get the inverse Laplace transform of The given function,which are Partial Fraction method Convolution integral method
EN
TS .IN
Lim S X(S) x(0) = x(oo ) x(0) S 0
91
Network Analysis to reduce it to proper fraction. ii) Q(S) should be in the factored form. Convolution-integral method: If L { x(t) } = X(S) L { h(t) } = H(S) Then L { x(t) * h(t) }= X(s) H(S) Where * is the convolution of two functions given by oo x(t) * h(t) = x ( T) h( t-T ) d T -oo
10ES34
Three important Singularity functions:
The Unit-step function is defined as u(t) = 0 t< 0 =1 t>0
TS
The step function can have a discontinuiy For example in sequential switching .The unit Step function that occurs at t=a is expressed as u(t-a) which is expressed as
TU D
They are called Singularity functions because they are either not finite or they do not posess finite derivative everywhere. u (t) Unit step function:
EN
u(t-a)
The three important singularity functions employed in circuit analysis are the unit step function u(t) the delta function (t) the ramp function r(t)
TS .IN
t t 92
CI
CITSTUDENTS.IN
u( t-a ) = 0 (t-a )< 0 = 1 (t-a)> 0
We use step function to represent an abrupt change in voltage or current , like the changes that oo Occur in the circuit of control engineering and digital systems.
Network Analysis
10ES34
Laplace transformation of unit step function is given by L { u( t) } = e-St dt 0 = - 1/ S [ e-oo - e0 ] = 1 S oo Similarly L{ u (t-a) } = u ( t-a) e-St dt a oo = - 1 e-St = 1 e- a S S a S
Impulse function:
The derivative of the unit step function is the unit impulse function (t) (t) i.e. (t) = d/dt { u(t) } = 0 t< 0 =1 t=0 =0 t>0
The unit impulse may be visualized as very short duration pulse of unit area This may be expressed mathematically as 0+ (t) dt = 1 0Where t= 0- indicates the time just before t=0 and t=0+ denotes the time Just after t=0. Since the area under the unit impulse is unity, it is practice to write 1 beside the arrow. When the impulse has a strength other than unity the area of the impulse function is equal to its strength. Since (t) = d/dt { u(t) } L { (t) } = L [d/dt { u(t) }] = S X 1 / S = 1
Ramp function:
CI
TS
Integrating the unit step function results in the unit ramp function r(t) t r(t) r (t) = u (T ) dT = t u ( t) - oo = 0 t<0 = t t>0
In general a ramp is a function that changes at a Constant rate. A delayed ramp function is shown in figure Mathematically it is described as follows
TU D
EN
TS .IN
0 t 93
CITSTUDENTS.IN
Network Analysis
10ES34
r(t-t0 ) = 0 t< 0 r (t- t0 ) = t t0 t > 0 Laplace transformation of a ramp function is given by t L { r ( t ) } = L [ u ( t ) dt ] 0 t0 = 1 / S X 1 / S = 1 / S2 L { r ( t t 0 ) } = 1 / S X 1 / S e-t0S t
= 1 e- toS
CI
CITSTUDENTS.IN
TS
TU D
EN
94
TS .IN
Network Analysis
10ES34
1) Obtain the Laplace transform of a periodic function with a suitable example wave form. Also find the Laplace transform of the following wave form shown in Fig.
9) ) State and prove convolution theorem. Using the same find f(t) when F(s) =
10) Using Laplace transform determine the current in the circuit shown in Fig. 25 when the switch S is closed at t=0 . Assume zero initial condition .
11) Find the Laplace transform of i) 6(t) ii) t iii) e-at iv) sin w t v)u(t) 12) Obtain the Laplace transform of sawtooth waveform in the Fig.
CI
CITSTUDENTS.IN
13) Find the Laplace inverse of using convolution integral 14) State and prove (i) initial value theorem and (ii) final value theorem as applied to L transform. What are the limitations of each theorem?
8) Obtain the Laplace transform of a full wave rectified sine wave of amplitude 1 and period secs.
TS
TU D
EN
TS .IN
95
Network Analysis
10ES34
9) The current function i(t) shown in fig. 10 is impressed on a capacitor C. what should be the strength A of the impulse so that the voltage across the C becomes zero for t > 5secs.
10) In the circuit shown in fig. 11, the switch is opened at t = 0, with V = 1V, C = 1F L = H, G = 1 find the node voltages V1 (t) and V2(t) by L transform method.
11 ) The switch in the network of Fig. 17 open at t=0. use Laplace t ransformation analysis to determine the v oltage across the capacitor for t2' 0.
CI
CITSTUDENTS.IN
TS
TU D
EN
96
TS .IN
Network Analysis
10ES34
Unit: 8 Two port network parameters : Syllabus of unit :
Hrs: 06
CI
CITSTUDENTS.IN
TS
TU D
EN
97
TS .IN
Definition of z, y, h and transmission parameters, modeling with these parameters, relationship between parameters sets.
Network Analysis
10ES34
TWO PORT PARAMETERS:

i1 1 V1 i1 2 i1
+
i2 Network
+ -
Network
-
V1 i1
V2
-
Network
i2 Two port Multi port
One port
PORT:- Pair of terminals at which an electrical signal enters or leaves a network. One port network:- Network having only one port.
Ex: Domestic appliances, Motor, Generator, Thevinins or Norton networks Two port
network:- Network having an input port and an output port. Ex:Amplifiers,Transistors, communication circuits, Power transmission & distribution lines Filters,attenuators ,transformers etc
independent sources.inside..
CI
CITSTUDENTS.IN
circuited or short circuited. In these networks there are four variables V1, I1 and V2, I2 . Two of them are expressed in
terms of the other two, to define two port parameters.
TS
lines DistributionsLines,Communication lines. Two port networks act as building blocks of electrical or electronic circuits such as electronic systems, communication circuits, control systems and transmission & distribution systems. A one port or two port network can be connected with another two port network either in cascade, series or in parallel. In Thevinins or Nortons networks , we are not interested in the detailed working of a major part of the network. Similarly it is not necessary to know the inner working of the two port network but by measuring the voltages and currents at input and at output port, the network can be characterized with a set of parameters to predict how a two port network interact with other networks.Often the circuit between the two ports is highly complex The two port parameters provide a shorthand method for analyzing the input-output properties of two ports without having to deal directly with the highly complex circuit internal to the two port. These networks are linear and passive and may contain controlled sources but not
Ex: PowerTransmission
While defining two port parameters we put the condition that one of the ports is either open
TU D
EN
Multi port network:-Network having more than two ports.
TS .IN
98
Network Analysis
10ES34
Four important Parameters Sl. No. 1. 2. 3. 4. Parameters z Parameters y parameters h parameters t parameters Dependent Variable V1, V2 I1, I2 V1, I2 V1 , I1 Independent Variable I1, I2 V1, V2 I1, V2 V2 , I2 Equations IV1 l I z11 = LV2 J L z21 I I 1 l I y11 = L I 2 J L y 21 I V1 l = z12 l I I 1 l z 22 J L I 2 J y12 l IV1 l y 22 J LV2 J
DEFINITIONS
(1) Z parameters (open circuit impedance parameters) V1= z11I1 + z12I2 V2= z21I1 + z22I2 z11 = z 21 = V 1
EN
I2 + V2 _ I2 + V2
I 1 I2 = 0 V2 I 1 I2 = 0
For
z11 and z21 - output port opened z12 and z22 - input port opened
Equivalent networks in terms of controlled sources ;
TS
Network (i) I1
z11
CI
V1 _
Network (ii)
By writing
V1 = (z11 z12) I1 + z12 (I1 + I2) V2 = (z21 z12) I1 + (z22 z12) I2 + z12 (I1 + I2) z11 z12 + I1 CITSTUDENTS.IN z12 z22 z12 (z21 z12)I1 +
TU D
z22 + z21I1 + z12I2
Hence the name open circuit impedance parameters
TS .IN
z12 = z 22 = V1 I 2 I1 = 0 V2 I2 I1 = 0 99
I h11 h12 l II1 l L I 2 J Lh 21 h 22 J L V2 J IV1 l I A B l IV2 l = L I 1 J LC D J L I 2 J
Network Analysis
10ES34
The z parameters simplify the problem of obtaining the characteristics of two 2 port networks connected in series (2) y parameters I1= y11V1 + y12 V2 I2= y21V1 + y22 V2 y11 = y21 = I1 V1 I2 = 0 y12 = y22 = I1 V2 I1 = 0 I2 V2 I1 = 0
I2 V1 I2 = 0
Equivalent networks in terms of controlled sources I1 + y12V2 V1 y11 y21V1 y22
(ii) by writing I1 = (y11 + y12) V1 - y12 (V1 + V2)
I2 = (y21 y12) V1 + (y22 + y12) V2 - y12 (V2 V1)
TS
+
TU D
y12 y22 + y12
EN
y11 + y12
(y21 + y12)V1 V2
CI
V1
The y parameters are very useful to know the characteristics of two 2 port Networks connected in parallel
CITSTUDENTS.IN
TS .IN
I2 + V2 +
For
y11 and y21 - port 2 is shorted z12 and z22 - port 1 is shorted
Hence they are called short circuit admittance parameters
100
Network Analysis
10ES34
Hybrid parameters:V1= h11 I1 + h12 V2 I2 = h21 I1 + h22 V2 h11 = h22 = V 1 I 1 V2 = 0 I2 I 1 V2 = 0 h12 = h22 = V1 V2 I1 = 0 I2 V2 I1 = 0
Equivalent Network in terms of controlled sources; I1 + h12 V2 V1 h11 + h21 I1 h22
Parameter values for bipolar junction transistors are commonly quoted In terms of h parameters
Transmission or ABCD parameters

V1= AV2 - BI2 I1 = CV2 - DI2 A= V1 V2 I2 = 0 I1
TU D
C= V2 I2 = 0 I I1 l I z11 = L I 2 J L z21 z12 l IV1 l z22 J LV2 J
1
EN
Relationship between two port parameters:-
CI
Relationship between different two port parameters can be obtained as follows. From the given set of two port parameters, rearrange the equations collecting terms of dependent variables of new set of parameters to the left. Then form matrix equations and from matrix manipulations obtain the new set in terms of the given set. (i) Relationship between z and y parameters for x parameters [V]=[z][I] [I ] = [z ]1[V ] then
CITSTUDENTS.IN
TS
As the name indicates the major use of these parameters arise in transmission Line analysis and when two 2 ports are connected in cascade
TS .IN
I2 + V2
B= D=
V1 I 2 V2 = 0 I1 I 2 V2 = 0
101
Network Analysis
10ES34
I y11 L y 21 I z11 L z 21
1 I z22 z12 l IV1 l z L z 21 z11 J LV2 J z12 l I z 22 y12 l z z = z 21 z11 y22 J z J L z = z12 l z 22 J = 1 I y 22 y L y 21 y12 l y22 J
where !Jz = z11 z22 z12z21
similarly
IV l I y 1 = 11 L I 2 J L y 21
TU D
= 1 I 1 y11 L y21
0 l I1 y12 l I I1 l 1J L0 y22 J LV2 J 0 l I1 y12 l I I 1 l 1 I 1 = y11 L y 21 y11 J L0 y 22 J LV2 J y12
TS
I h11 Lh21
I 1 h12 l y = 11 y 21 h22 J L y11
(iii) To Express T-parameters in terms of h-Parameters:
CI
V1 = AV2 -BI2 I1 = CV2-DI2
Equations for T-parameters, (1)
EN
1
(ii) Relationship between [ y ] and [ h ] From I1 = y11V1 + y12V2 I 2 = y 21V1 + y 22V2 Rearranging y11V1 = I 1 y12V2 y 21V1 I 2 = y 22V2 I y11 0 l IV1 l I1 y12 l I I1 l = L y 21 1J L I 2 J L0 y 22 J LV2 J
y12 y21 y11 y22 J LV2 J
y12 l y11 I I 1 l y LV2 J y11 J
Equations for h-parameters, V1 = h11I1 + h12 V2 I2 = h21I1+ h22 V2 (2)
Re arranging Equation (2) V1 - h11I1 = h12 V2 - h21I1 = h22V2 -I2
CITSTUDENTS.IN
TS .IN
l I I1 l 102
Network Analysis I V1 l I1 h11 l = L I1 J L0 h 21 J 1 I h 21 For which [T ] = h 21 L 0

1
10ES34 I h12 0 l IV2 l
Lh 22 1J L I 2 J h11 l I h12 0 l 1 J Lh 22 1J h11 l I h h 21 = 1 J h 22 L h 21 h11 l h 21 1 h 21 J
1 Ih11 h 22 h 21 h12 = h 22 h 21 L
By a similar procedure, the relationship between any two sets of parameters can be established. The following table gives such relationships:
Y y11 y21 y22 y [z] y 21 y 1 y11 y12 y22 y12 y y11 y y12 y11 y y11 z 22 z z 21 z
[y]
z z12 z z11 z
EN
z11 z12 h h22 z 21 z 22 h21 h22 z z 22 z12 z 22 h11 h21 h h21 h22 h21 z 21 z 22 z11 z 21 1 z 22 z z 21 1 z 21 z 22 z 21
TU D
y21 y11 y 22 y 21 y21 1 y 21 y y11 y 21
[h]
TS
[t]
CI
COMPUTATIONS OF TWO PORT PARAMETERS: A. By direct method i.e. using definitions For z parameters, open output port (I2=0) find V1 & V2 in terms of I1 by equations Calculate Z11=V1/I1 &Z21=V2/I1. Open input port (I1=0) find V1 & V2 in terms of I2.Calculate Z12=V1/I2 &Z22=V2/I2 Similar procedure may be followed for y parameters by short circuiting the ports h & t parameters may be obtained by a combination of the above procedures.
CITSTUDENTS.IN
TS .IN
H 1 h12 h11 h11 h21 h11 h h11 D B 1 B T t B A B h12 h22 1 h22 A t C C 1 C D C h12 h22 h11 h21 1 h21 B t D D 1 C D D A B C D
103
Network Analysis B. z and y parameters:By node & mesh equations in standard form
10ES34
For a reciprocal network (passive without controlled sources) with only two current Sources at input and output nodes,the node equations are I1=Y11V1+Y12V2+Y13V3+--------- +Y1n Vn I2=Y21V1+Y22V2+Y23 V3+--------- +Y2n Vn 0 =Y31V1+Y32 V2+Y33V3+--------- +Y3n Vn -------------------------------------------------0 = Yn1 V1 +Yn2 V2 +Yn3 V3---------+YnnVn then V1 = 11 I1 + 21 I 2 V2 = 12 I1 + 22 I2 where is the det er min ent of the Y matrix. 1 j cofactor of Y of
1j
Comparing these with the z parameter equations. we have z11 = 11 z 22 = 22 z12 =
V2 = Z 21 I 1 + Z 22 I 2 + .......... + Z 2 m I m O=
Then
D21 V2 D D D D22 I 2 = 12 V V2 1 + D D I1 = V1 +
where D is the determinant of the Z matrix and Dij is the co-factor of the element Zij of Z matrix .comparing these with [y] equations
TS
TU D
D11 D11 D y 22 = D22 D
O = Z m1 I 1 + Z m2 I 2 + ........... + Z mm I m
EN
y12 = D12 D
Similarly for such networks, the loop equations with voltage sources only at port 1 and 2 V1 = Z11 I 1 + Z12 I 2 + .......... + Z1m I m
CI
Thus we have y11 =
Alternative methods
For z parameters the mesh equations are
CITSTUDENTS.IN
TS .IN
21 z 21 = 12 y 22 = D22 D 104
Network Analysis V1 = Z11 I 1 + Z12 I 2 + .......... + Z1m I m V2 = Z 21 I 1 + Z 22 I 2 + .......... + Z 2 m I m O= O = Z m1 I 1 + Z m 2 I 2 + ........... + Z mm I m By matrix partitioning the above equations can be written as
10ES34
LO J
Similarly for Y parameters
TU D
I I1 l I Y11 I2 Y21 = Y31 0 0 Y L J L n1 Y12 Y22 Y32 Yn 2
I V1 l II l = M NQ 1 P 1 L V2 J LI 2 J
TS CI
CITSTUDENTS.IN
EN
LP Q J LI 2 J
I V1 l IM V2 O =
N l I I1 l I2 I3
Y2 n V2 Y3n V3 Ynn J LVn J
TS .IN
Z nn J LI n J
I V1 l I Z11 Z12 V2 Z 21 Z 22 0 = Z 31 Z32 L 0 J LZ n1 Z n 2
Z1n l I I1 l Z2n I 2 Z3n I 3
Y1n l I V1 l
105
Network Analysis I I1 l IM I2 O = LOJ I I1 l LI 2 J LP N l I V1 l V2 V3 Q J L V2 J Vl ]I V

1
10ES34
= M NQ 1 P
V1 I1 -
Z3
I2
V2 -
V2 = Z 3 I1 + (Z 2 + Z 3 )I 2 z11 = Z1 + Z 3
from which
If the network is brought to IT network as shown I1 + V1 Y3 I2 + Then
Y3 V2 )V Y1 I1 = (Y1 + Y3Y 21 V2 I 2 = Y3 V1 + (Y2 + Y3 )V2 from which y 22 = Y2 + Y3 y11 = Y1 + Y3 y12 = y 21 = Y3
SYMMETRICAL CONDITIONS
A two port is said to be symmetrical if the ports can be interchanged without changing the port voltage and currents..
CI
TS
i.e. if
TU D
V1 V = 2 I =0 I1 I 2 = 0 I 2 1
By using the relationship between z and other parameters we can obtain the conditions for Symmetry in terms of other parameters. As z11=z22, in terms of y we have y11=z12/dz & y22=z1/dz, y11=y22.
CITSTUDENTS.IN
EN
z11 = z 22
106
z12 = z 21 = z13
TS .IN
z 22 = Z 2 + Z 3
C. By reducing the network (containing passive elements only) to single T or D by T-D transformations If the network is reduced to a T network as shown I2 Then Z2 Z1 + + V1 = (Z1 + Z 3 )I1 + Z 3 I 2
Network Analysis
10ES34
In terms of h parameters as z11=h/h22 & z22=1/h22 we have h=h11h22- h12h21 = 1. In terms of t parameters as z1=A/C & z22=D/C the condition is A=D
Reciprocity condition in terms of two port parameters I1 + V _ + V1 N + V2 I2 Ia Ib I1 + V1 N Fig 2 I2 + _V
Fig 1 For the two networks shown for Fig 1 Fig 2 V1 = V V2 = V I2 = -Ia I1 = -Ib
Condition for reciprocity is Ia = Ib From z parameters V1 = z11 I1 + z12 I 2 V2 = z 21 I1 + z 22 I 2 I a = z 21 V = z12 V z z From fig(2) O = z11 I b + z12 I 2
TU D
Ib = z 21V z
z12 = z 21
V = z 21 I b + z12 I 2
TS
For reciprocity with z12=z21, In terms of y parameters z12= - y12/y & z21=-y21/y condition is In terms of t parameters z12=t/C & z21=1/C the condition is
EN
V = z11 I1 z12 I a O = z 21 I1 z 22 I a
we have from fig(1)
then for I a = I b
In terms of h parameters z12= h12/h22 & z21= - h21/h22 the condition is h12= - h21 t=AD - BC=1
CI
CITSTUDENTS.IN
TS .IN
V2 = 0 V1 = 0 y12= y21 107
Network Analysis Parameters
10ES34
Condition for
Reciprocity Symmetry
z y h t
z12=z22 y12=y22 h12= -h21

AD-BC=1
z11= z22 y11=y22 h11.h22-h12.h21=1

A=D
CASCADE CONNECTION:+
V1
-
In the network shown 2 two port networks are connected in cascade
TU D
Da J for Nb,
For Na, [t ] =
IA a L Ca
Ba l
For the resultant network N
From the cascaded network we have
TS
V1a = A a V2a Ba I 2a I1a = C a V2a D a I 2a
V1b = A b V2 b Bb I 2 b I1b = C b V2 b D b I 2 b V1 = AV2 BI 2 I1 = CV2 DI 2
CI
CITSTUDENTS.IN
EN
[t ] =
IA b L Cb Bb l Db J
I1 + I1a V1a -
I2a+ Na V2a -
+ I1b V1b -
Nb
I2b + V2a -
[t ] = I
Bl
L C DJ
for network N
TS .IN
I+ 2
-
I1
I2
+ -
+ -
V2
V1
V2
for network N a for network N b
108
Network Analysis From the network I1 = I1a I 2a = I1b V1 = V1a I V1a l I A a = L I1a J L C a or IV1a l I A a = L I1a J L Ca = IA a L Ca I2 = I2 b V2 = V2 b and I V1b l I A b = L I1b J L C b Bb l I V2 b l D b J L I 2 b J Ba l I V2a l V2a = V1b
10ES34
D a J L I 2a J Ba l IV1b l I A a Ba l IA b = D a J L I1b J L C a D a J L C b Ba l I A b Bb l I V2 l
Bb l I V2 b l D b J L I 2 b J
I A Bl = L C DJ L Ca Da J L Cb [T ] = [Ta ][Tb ]
Db J
CI
CITSTUDENTS.IN
TS
TU D
EN
109
TS .IN
D a J L C b D b J L I 2 J Bb l I A a Ba l I A b
Network Analysis
10ES34
1) Explain Z and Y parameters with equivalent circuit Also express Z- parameters in terms of Y parameters. 2) Find the h- parameters of the network shown in Fig. Give its equivalent circuit
3) Find Y parameters for the network shown in fig.
4) Find the transmission or general parameters for the circuit shown in Fig
5) Define y and z parameters. Derive relationship such that y parameters expressed in terms of z parameters and z parameters expressed in terms of y parameters 6) Define h and T parameters and derive expressions for [h] in terms of [T]. and for the two port network shown in fig. 13.
CI
7) Find
TS
TU D
EN
TS .IN
110
CITSTUDENTS.IN
Network Analysis
8 For the network shown in fig.14 obtain the o.c. impedance parameters
10ES34
9 Find
and
for the two port network shown in fig. 13
CI
TS
TU D
EN
CITSTUDENTS.IN 111
TS .IN

Ece III Network Analysis (10es34) Notes

Uploaded by

Copyright:

Available Formats

Ece III Network Analysis (10es34) Notes

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ece III Network Analysis (10es34) Notes

Uploaded by

Copyright:

Available Formats

Network Analysis

Network Theorems 1: Superposition, Reciprocity and Millmans theorems

UNIT 4: Network Theorems - II:

Thevinins and Nortons theorems; Maximum Power transfer theorem 6 Hours

Coverage in the Texts:

UNIT 5: Text 2 8.1 to 8.3

UNIT 6: Text 1 Chapter 5;

UNIT 7: Text 1 7.4 to 7.7; 8.1 to 8.5

UNIT 8: Text 1 11.1 to 11.

UNIT 3 and UNIT 4: Text 2 7.1 to 7.7

Unit: 1 : Basic Concepts Syllabus of unit 1:

1. Network Analysis, M. E. Van Valkenburg, PHI / Pearson Education

4. Network analysis , Roy Choudry.

3. Network theory , Ganesh Rao.

1. OHMS LAW IAB-Current from A to B

Reference Direction E1-E2=V1 -V2+V3-V4=I1Z1 -I2 Z2+I3Z3-I4Z4

Voltage Division Vi =(Zi/Z)V

Current Division II=(Yi/Y)I

Network Analysis I=V/Z=V1/Z1=V2/Z2=-------------V=I/Y=I1/Y1=I2/Y2=-------------

I2 = V = (30.6 9.550 ) Z2 I3 = V = (30.6 9.550 ) Z2

VAC= (7-8i)(10) = 106.3 -48.80

Voltage Source (ideal)

Current Source (ideal)

Practice Voltage source

For equivalence ES = IS ZS+ZL Therefore ES = IS Z P and ZS = Z P

(a) E shift operation

(b) I shift operation

Sources with equivalent terminal characteristics

(i)Series voltage sources

(ii) Parallel voltage sources(ideal)

(iii) Parallel current sources

(v)Voltage source with parallel Z

(vii) V and I in Parallel

Adding (1), (2) and (3)

Substituting for ZB + ZC from (2) = ZA = ZCA ZAB ZAB+ ZB + ZCA

(ZAB ZBC + ZBCZCA + ZCAZAB) ZAB+ ZBC + ZCA

2 (ZAB ZBC + ZBCZCA + ZCAZAB) ZAB+ ZBC + ZCA - (ZB + ZC)

ZAB ZBC ZAB ZBC ZCA ZAB Z!J . 3

ZAB = ZBC = ZCA = Z!J then ZA = ZB = ZC = ZY =

YAC C YBC YA (YB + YC) YA+ YB + YC

For equivalence YAB + YCA =

YA YB - (YBC + YCA) YA substituting from (3)

transformation techniques only. Then verify by node equations

current in 3+j4 is zero . Take = 50 rad/sec.

3. Network theory , Ganesh Rao.

4. Network analysis , Roy Choudry.

New Age International

Net work Topology

Branch (or Twig):

Two possible trees

Complete Incidence matrix ( i )Complete incidence matrix:

Properties of a complete incidence matrix

Number of nodes = n = 4 ( say A. B. C and D) Number of branches = b = 6 ( say 1, 2, 3, 4, 5 and 6)

Prepare a tabular column as shown. Nodes Branches 1 2 1 -1 0 0 0 1 -1 0

Tie set Analysis:

tree (In thick lines) Co-tree (In dotted lines)

Tie set schedule Tie set 1 2 3

Analysis of the net work based on Tie set schedule

From the tie set schedule we make the following observations.