SUMTEL Repeater Intro 20dBm

Introduction of 20dBm RF Repeater
1.
Overview
2. Specification
3. Block Diagram
4. Major Function
5. Coverage Simulation
6. Installation Procedure
7. GUI User Guide
8. NMS User Guide
June . 2012
1. Overview
DBR1800/850/20dB repeater is used to cover shadow area of small building
and shopping center ( under 1,000m2 Area)
System Configuration
-. RF module : LNA,AMP,Mixer, Filter etc.
-. PSU : Output +6V / 7A
-. MCU Bd : Status LED, USB Port, GSM Modem
Temperature sensor etc.
In/Out port : FWD/RVS ANT, CPL(-30dB), AC
Major Features
- GSM/WCDMA dual band Repeater
- Remote Control Function
- Alarm Report Function
- Local GUI function
- Auto-shutdown Function
- Auto Gain Control
<Front Side>
<Back
Side>
2. Specification
Parameter
Frequency Range
Selectivity
Output Power/ Total
Gain
Out of Band Gain
Value
Remarks
Down Link
1817.5 ~ 1842.9MHz
Up Link
1722.5 ~ 1747.9MHz
Down Link
884 ~ 894MHz
Up Link
839 ~ 849MHz
3dB Bandwidth
25.4 0.4 MHz
GSM1800
Down Link
>= +20dBm @ Total
0.1 Watts
Up Link
>= +20dBm @ Total
0.1 Watts
Range
45 ~ 75dB
GSM1800
WCDMA850
Adjustable Range
30dB
Adjustment Step
1dB
Adjustment Accuracy
<= 0.7dB
400kHz
600kHz
1MHz
5MHz
50dB
40dB
35dB
25dB
GSM1800
2.7foffset<3.5 MHz
60dB
3.5foffset<7.5 MHz
45dB
7.5foffset<12.5 MHz
45dB
12.5foffset
ALC Range
(Automatic Level Control)
Passband Ripple
GSM1800
WCDMA850
WCDMA850
35dB
30dB
<= 3dB p-p
GSM1800
<= 2dB p-p
WCDMA850
2. Specification
Input Power Level / Total
-25dBm ~ -55dBm
Noise Figure
Group Delay
<= 6dB
<= 5sec
9KHz~1GHz
-36dBm
1GHz~12.75GHz
-30dBm
9KHz~1GHz
-36dBm
1GHz~12.75GHz
-30dBm
-21.5dBm/30KHz
2.5MHz
-33.5dBm/30KHz
3.5MHz
-20.5dBm/1MHz
4.0MHz
9KHz ~ 150KHz
-13dBm/1KHz
150KHz ~ 30MHz
-13dBm/10KHz
30MHz ~ 1GHz
-13dBm/100KHz
1GHz ~ 12.75GHz
-13dBm/1MHz
Down Link
>= +22dBm
Up Link
>= +22dBm
Intermodulation Distortion (IMD)

Spurious Emission
In Band
Spurious Emission
Out Band
Shut Down
Output Power Monitor
30 1dB
Impedance
50 ohms
VSWR
<= 1.5 :1
ACLR
Remote Monitoring
GSM1800
GSM1800
WCDMA850
GSM1800 /
WCDMA850
> 0.96
<= 12.5%
<= -35dB
GSM1800
WCDMA850
WCDMA850
5MHz
10MHz
5MHz
10MHz
20dBc
20dBc
45dBc
50dBc
WCDMA850
WCDMA850
WCDMA850
WCDMA850
Module
Built-in
SIM Card(Data Enabled)
Yes
Wave Form Quality

EVM
PCDE
ACRR
GSM1800
WCDMA850
2. Specification
USB
Yes
Power_LED
GREEN
2Color_Led
2Color_Led
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
-10 ~ 50
MINI_USB
Local Access & Monitoring

Status_LED
Control Function
Monitor Function
PA Enable
Gain
ALC Level
Shut Down Level
PA Status
Output Power
Gain
Temperature
Operating temperature
GSM1800
WCDMA850
Power Supply
110/220VAC, 50~60Hz
Backup
1Hour
Optional
RF In/Out Connector
Monitor Connector
Local Access Connector
Power Input Connector
Power Consumption
Dimension(WxHxD)
Weight
Software
Test Cable
Manual
Mounting Kit
N -Type Female
SMA -Type Female
USB Female
T.B.D.
35W
255 x 355 x 130
< 6kg
Yes
Yes
Yes
Yes
Commissioning Materials
Installation Materials
mm
GUI
Bolts
3. Block Diagram
GSM Modem
( Remote Control Function)
H/W Temp
Compensation
4. Major Function
Auto Level Control
Adjust Max gain level to make Downlink Output level is not over +20dBm 1dB,
Control MAX Gain value 45 ~ 75dB.
AGD Mode
-. FWD Gain is linked to RVS Gain
-. If ON : FWD/RVS gain is linked
-. If Off : FWD/RVS gain is not linked
AGD Offset
- Difference between FWD Gain and RVS Gain
4. Major Function
Automatic Shutdown
If Downlink/Uplink Output level is over +22dBm1dB for 5 sec, Repeater

Downlink and Uplink is Shutdown for 5 sec .
This auto-shutdown algorithm can repeat 3 times
Operator can adjust the times of ASD algorithm and duration of overpower shutdown
period.
5. Coverage Simulation
- Define : The distance of -65dBm received signal

power to mobile handset
- Coverage area: Total 1,000m2 (at WCMA 850)
- Connectable 2~4 service antennas
- Considered -15dB as barrier loss
- Typically received signal sensitivity of mobile
handset is -104dBm
(GSM, DCS, CDMA, WCDMA)
- Coverage can be expanded with more service antenna
Floor
Small
Out
3Way
Divider
RF
Cable
B1
B2
B3
20dBm
-5dB
-5dB
Service
ANT
Free
Space
0dBi
-63.5dB
7dBi
-70.5dB
7dBi
-70.5dB
Barrier
Input
Handset
Service Radius
(@ -65dBm)
20m
-15dB
-65dBm
44m
44m
-. GSM/WCDMA Input Level check
-25dBm ~ -55dBm/Total (typical)
Input Power(dBm) Output Power(dBm) System Gain(dB) Isolation(dB)
-25
20
45
60
-35
20
55
70
-45
20
65
80
-55
20
75
90
-65
10
75
90
-75
75
90
-. Bracket Installation ( Next Page)

-. Connect Cable (Donor / Service ANT.)
Donor ANT. port
Service ANT. port
Bracket Installation
Install Bolt
Wall Mounted
Bracket
Braket Insert
Point
7. GUI User Guide

- (Graphical User Interface)
- Double Click Execution File
(DBR1800_850_20dBm.exe)
1. COM Port Setting

2. CONNECT Click
3. MAIN Click
4. Input Operator #1 : ARM1 MIN
5. Input Operator #2 : ARM2 MIN
6. Input Repeater phone No.: MIN
GSM Modem RSSI
PLL Status
- Green : normal
- Red : abnormal (NMS Report)
7. GUI User Guide

- Checking System Gain and Output Power
Path Control
On : normal
Off : abnormal (NMS Report)
Manual ATT control

- 30dB / Max
- If ALC Off : 0dB
Gain : Gain status
75dB ~ 45dB
Output Power : Output Power status
24dBm ~ -7dBm
if <-7dBm NA dispaly
7. GUI User Guide

- ALC Control / Status
ALC Mode (Automatic Level Control)

- On : normal
- Off : abnormal
ALC Level
- 20dBm defoult
- settable
ALC Atten
- Applied ATT Vaule
Green LED : normal

Red LED : abnormal
AGD Mode
-. FWD Gain is linked to RVS Gain
-. If ON : FWD/RVS gain is linked
-. If Off : FWD/RVS gain is not linked
AGD Offset
- Difference between FWD Gain and RVS Gain
7. GUI User Guide

- ASD Control / Status
ASD Mode (Automatic Shutdown)

- On : normal
- Off : abnormal
ASD Level
- 22dBm defoult
- settable
Time
- Time period of Over Power & Shutdown
- Settable
Count
- Max number of ASD Algorithm
- settable
Green LED : normal
Red LED : abnormal
7. GUI User Guide

- Control / Status
Communication status
Factory Defoult set
System Reset
Apply Input vaule
8. NMS User Guide

- Double Click Execution file
(DBR1800_850_20dBm.exe)
1. COM Port Setting
2. Modem Con. Click
8. NMS User Guide

3. Modem Check Click
4. OKE0 Message check
8. NMS User Guide

5. Input Repeater Phone No
6. Connect Click
8. NMS User Guide
7. Connection Success!!
8. NMS User Guide
8. CONNECT 9600/RLP
9. MAIN Click
8. NMS User Guide

10. MAIN Display

SUMTEL Repeater Intro 20dBm

Uploaded by

Copyright:

Available Formats

SUMTEL Repeater Intro 20dBm

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SUMTEL Repeater Intro 20dBm

Uploaded by

Copyright:

Available Formats

Introduction of 20dBm RF Repeater

Out of Band Gain

25.4 0.4 MHz

>= +20dBm @ Total

>= +20dBm @ Total

<= 2dB p-p

Intermodulation Distortion (IMD)

SIM Card(Data Enabled)

Wave Form Quality

Local Access & Monitoring

If Downlink/Uplink Output level is over +22dBm1dB for 5 sec, Repeater

- Define : The distance of -65dBm received signal

-. Bracket Installation ( Next Page)

Donor ANT. port

Service ANT. port

7. GUI User Guide

1. COM Port Setting

GSM Modem RSSI

7. GUI User Guide

Manual ATT control

7. GUI User Guide

ALC Mode (Automatic Level Control)

Green LED : normal

7. GUI User Guide

ASD Mode (Automatic Shutdown)

7. GUI User Guide

Factory Defoult set

Apply Input vaule

8. NMS User Guide

1. COM Port Setting

2. Modem Con. Click

8. NMS User Guide

4. OKE0 Message check

8. NMS User Guide

8. NMS User Guide

8. NMS User Guide

8. NMS User Guide

You might also like