Governor

GOVERNOR
PRESENTED BY:- FAIZ AKRAM

ROLL NO:-120106096
GOVERNOR
The function of a governor is to regulate the mean speed of
an engine, when there are variations in the load .when the
load on an engine increases its speed decreases. And when the
load on the engine decreases its speed increases when the
load decreases, and the governor decreases the supply of
working.
There are two types of governor
1. Centrifugal governor 2. Inertia governor
INERTIA GOVERNOR
This works on a different principle. The governor balls are
arranged so that the inertia forces caused by angular
acceleration or retardation of the governor shaft tend to alter
their positions. The amount of the displacement of the balls is
controlled by springs. The advantage of this type of governor
is that the positions of the balls are affected by the rate of
change of speed of the governor shaft
CENTRIFUGAL GOVERNER
The centrifugal governors are based on the balancing of
centrifugal force on the rotating balls by an equal and opposite
radial force known as the controlling force. It consists of two
balls of equal mass, which are attached to the arms as shown
in Fig. 1.1 These balls are known as governor balls or fly
balls. The upper ends of the arms are pivoted to the spindle, so
that the balls may rise up or fall down as they revolve about
the vertical axis.
The arms are connected by the links to a sleeve which is keyed

to the spindle. This sleeve revolves with the spindle. but can
slide up and down. The balls and the sleeve rises when the
spindle speed increases and falls when the speed decreases.
Fig 1.1
WATT GOVERNOR
The simplest form of a centrifugal governor is a watt governor,
as shown in Fig. 1.2. It is basically a conical pendulum with
links attached to a sleeve of negligible mass.
H=895/ N2
where H is the height of the governor
N is the speed of the balls
Fig 1.2
PORTER GOVENOR
The Porter governor is a modification of a Watts governor,
with central load attached to the sleeve as shown in Fig. 1.3.
The load moves up and down the central spindle.. Consider the
forces acting on one-half of the governor as shown in Fig. 1.3
Where is angular speed of the ball

W is the weight of the central load
w is the weight of the balls
h is the height of the governor
Fig. 1.3
PROELL GOVERNOR
The Proell governor has the balls fixed at G as shown in Fig.
1.4. The arms AO and OB are pivoted at O. Consider the
equilibrium of the forces on one-half of the governor.
Fig. 1.4
HARTNELL GOVERNOR
A Hartnell governor is a spring loaded governor as shown in
Fig. 1.5. It consists of two bell crank levers pivoted at the
points O, O to the frame. The frame is attached to the governor
spindle and therefore rotates with it. Each lever carries a ball
at the end of the vertical arm OA and a roller at the end of the
horizontal arm OC.
Where FC1 and FC2 are the centrifugal force at 1 and 2
Fig. 1.5
HARTUNG GOVERNOR
A spring controlled governor of the Hartung type is shown in
Fig.1.6 . In this type of governor, the vertical arms of the bell
crank levers are fitted with spring balls which compress
against the frame of the governor when the rollers at the
horizontal arm press against the sleeve.
FC*X=S*X + M.g.Y/2
Where x and y = Lengths of the vertical and horizontal arm of
the bell crank lever respectively
And S= Spring force
Fig.1.6
WILSON-HARTNELL GOVERNOR
A Wilson-Hartnell governor is a governor in which the balls
are connected by a spring in tension. An auxiliary spring is
attached to the sleeve mechanism through a lever by means of
which the equilibrium speed for a given radius may be
adjusted. The main spring may be considered of two equal
parts each belonging to both the balls. The line diagram of a
Wilson-Hartnell governor is shown in Fig 1.7
Fig 1.7
SENSITIVENESS OF GOVERNOR
The sensitiveness is defined as the ratio of the difference
between the maximum and minimum equilibrium speeds to the
mean equilibrium speed.
N1 = Minimum equilibrium speed,
N2 = Maximum equilibrium speed, and
N = Mean equilibrium speed =(N1+N2 )/2
Sensitiveness of the governor=(N2-N1)/N
STABILITY OF GOVERNOR
A governor is said to be stable when for every speed within the
working range there is a definite configuration i.e. there is
only one radius of rotation of the governor balls at which the
governor is in equilibrium. For a stable governor, if the
equilibrium speed increases, the radius of governor balls must
also increase.
EFFORT AND POWER OF

GOVERNOR
The effort of a governor is the mean force exerted at the sleeve
for a given percentage change of speed. It may be noted that
when the governor is running steadily, there is no force at the
sleeve. But, when the speed changes, there is a resistance at
the sleeve which opposes its motion. It is assumed that this
resistance which is equal to the effort, varies uniformly from a
maximum value to zero while the governor moves into its new
position of equilibrium.
The power of a governor is the work done at the sleeve for a

given percentage change of speed. It is the product of the
mean value of the effort and the distance through which the
sleeve moves.
Mathematically, Power = Mean effort lift of sleeve
THANKING
YOU

Governor

Uploaded by

Copyright:

Available Formats

Governor

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Governor

Uploaded by

Copyright:

Available Formats

What are the two main types of governors?

How does a centrifugal governor work?

GOVERNOR

PRESENTED BY:- FAIZ AKRAM

The arms are connected by the links to a sleeve which is keyed

Where is angular speed of the ball

Where FC1 and FC2 are the centrifugal force at 1 and 2

EFFORT AND POWER OF

The power of a governor is the work done at the sleeve for a

You might also like