Chapter 4 Energy and Energy Balance

Chapter 5
Energy and Energy Balance
Forms of Energy
Three component of total energy of a system Kinetic energy (Ek)
energy due to the translational motion of the system as a whole relative to some frame of reference (usually the earths surface) or to rotation of the system about some axis. energy due to the position of the system in a potential field (such as a gravitational or
Potential energy (Ep)
Transfer of Energy
In closed system (i.e. no mass is transferred across the system boundaries while the process is taking place), energy may be transferred between such a system and its surroundings in two ways as heat or work. Heat
Energy that flows as a result of temperature difference between a system and its surroundings.
First Law of Thermodynamics

Law
of conservation of energy, which state that energy can neither be created nor destroyed. form of first law of thermodynamics
General
Inlet Energy + Heat - Outlet Energy Work = Accumulation
Kinetic Energy Equation (Ek)
Kinetic energy, Ek (J) of an object of mass m (kg) moving with velocity u (m/s) relative to the surface of the earth is
1 E k mu 2 2
1 m 2 u E Ek m 2
k
If the fluid enters a system with a mass flow rate (kg/s) and uniform velocity u (m/s), the rate at which kinetic energy (J/s) is transported into the system is
Potential Energy Equation (Ep)
Gravitational potential energy, Ep

E p mgz
m
m gz E p
if the fluid enters a system with a mass flow rate (kg/s) and an elevation z relative to the potential energy reference plane.
E p E p 2 E p1 mg ( z 2 z1 )
Example 7.2-1
Water flows into a process unit through a 2 cm ID pipe at a rate of 2 m3/h. Calculate the kinetic energy transport in this stream in unit J/s. Solution: Ek= 0.870 N.m/s= 0.870 J/s
Class Discussion Example 7.2-2
Energy Balances on Closed System
Closed system
no mass is transferred across the system boundaries while the process is taking place
U E k E p Q W
Energy balance Final System Energy Initial System Energy = Net Energy Transferred to the System
Energy Balances on Closed System
When applying energy balance equation to a given process, the following point must be aware; 1. The internal energy of a system depends almost entirely on the chemical composition, state of aggregation (solid, liquid, or gas), and temperature of the system materials. If no temperature changes, phase changes, or chemical reactions occur in a closed system and if pressure changes are less than a few atmospheres, then U 0.
2.
If a system is not accelerating, then Ek = 0. If a system is not rising or falling, then Ep = 0.

If a system and its surroundings are at the same temperature or the system is perfectly insulated, then Q = 0. The process is then termed adiabatic.
3.
4.
Work done on or by a closed system is accomplished by movement of the system boundary against a resisting force or the passage of an electrical current or radiation across the system boundary. If there no moving parts or electrical current at the system boundary, then W = 0.
Class Discussion
Example
7.3-1
Energy Balances on Open System

In open system, mass is transferred across the system boundaries while the process is taking place. Therefore work must be done on open system to push mass in and work is done on the surrounding by mass that emerges W from the systems. Both work terms must be include in the W energy balance for open system The net work done by an open system
fl
Energy Balances on Open System
^ symbol is used to denote the specific V property ( property divided by mass or by mole) such as specific internal energy ( kJ/kg), specific volume ( m3/kg) and so on.
U PV H
One important property for energy balance on open system is specific enthalpy ( kJ/kg).
Energy Balances Equation for Open System

W E E Q H k p s
H m H
j output stream
m H
j input stream
E k p E
output stream output stream
m ju j 2
j
input stream
m ju j 2
j
gz j
m
input stream
gz j
Reference States and State Properties
It is not possible to know the absolute value of and for a process material, but we can determine the change in and change in corresponding to a specific change of state (temperature, pressure, phase). A convenient way to tabulate and is to choose a temperature, pressure and state of aggregation (i.e. phase) as a reference state. Since cannot be known absolute, for convenience we may assign a value o=0 to be reference state. Then 1= 1-0; 2= 2-0
Steam Table
Energy Balance Tips
When labeling flowchart, write down together the temperature, pressure and state of aggregation of the process material.
Q U
H Q
Normally (depend on the process description) for chemical process unit; shaft work, kinetic and potential energy change tend to be negligible compared to heat flows, internal energy and enthalpy
Mechanical Energy Balance
Important in the operations involve the flow of fluids to, from and between tanks, reservoirs and process unit. Mechanical energy balance for steady state flow of an incompressible fluid; where F is friction loss
P W u 2 s gz F 2 m P u 2 gz 0 2
THANK

Chapter 4 Energy and Energy Balance

Uploaded by

Copyright:

Available Formats

Chapter 4 Energy and Energy Balance

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Chapter 4 Energy and Energy Balance

Uploaded by

Copyright:

Available Formats

Chapter 5

Energy and Energy Balance

Potential energy (Ep)

First Law of Thermodynamics

Inlet Energy + Heat - Outlet Energy Work = Accumulation

Kinetic Energy Equation (Ek)

Potential Energy Equation (Ep)

Gravitational potential energy, Ep

Class Discussion Example 7.2-2

Energy Balances on Closed System

Energy Balances on Closed System

If a system is not accelerating, then Ek = 0. If a system is not rising or falling, then Ep = 0.

Energy Balances on Open System

Energy Balances on Open System

Class Discussion Example 7.4-1

Energy Balances Equation for Open System

output stream output stream

Class Discussion Example 7.4-2

Reference States and State Properties

Class Discussion Example 7.5-1

Class Discussion Example 7.5-3

Energy Balance Tips

Class Discussion Example 7.6-1

Class Discussion Example 7.6-2

Class Discussion Example 7.6-3

Mechanical Energy Balance

Class Discussion Example 7.7-1

Class Discussion Example 7.7-2

Class Discussion Example 7.7-3

You might also like