Scribd Logo
Upload

Welcome to Scribd!

  • 108 views

    Unsupported Commands in Cisco IOS Release 15.2 (2) S: Appendix

    Uploaded by

    David Munsell
    The document lists commands that are unsupported in Cisco IOS Release 15.2(2)S on the Cisco ME 3800X and ME 3600X switches. It is grouped by software feature and covers areas such as access control lists, routing, VLANs, QoS, SNMP, and others. Many debug, show, and clear commands are also unsupported due to hardware limitations of the switches.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    Unsupported Commands in Cisco IOS Release 15.2 (2) S: Appendix

    Uploaded by

    David Munsell
    108 views10 pages
    The document lists commands that are unsupported in Cisco IOS Release 15.2(2)S on the Cisco ME 3800X and ME 3600X switches. It is grouped by software feature and covers areas such as access control lists, routing, VLANs, QoS, SNMP, and others. Many debug, show, and clear commands are also unsupported due to hardware limitations of the switches.

    Original Title

    AppendixC Unsupported Commands

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document lists commands that are unsupported in Cisco IOS Release 15.2(2)S on the Cisco ME 3800X and ME 3600X switches. It is grouped by software feature and covers areas such as access control lists, routing, VLANs, QoS, SNMP, and others. Many debug, show, and clear commands are also unsupported due to hardware limitations of the switches.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    108 views10 pages

    Unsupported Commands in Cisco IOS Release 15.2 (2) S: Appendix

    Uploaded by

    David Munsell
    The document lists commands that are unsupported in Cisco IOS Release 15.2(2)S on the Cisco ME 3800X and ME 3600X switches. It is grouped by software feature and covers areas such as access control lists, routing, VLANs, QoS, SNMP, and others. Many debug, show, and clear commands are also unsupported due to hardware limitations of the switches.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 10

    A P P E N D I X

    Unsupported Commands in Cisco IOS Release 15.2(2)S


    This appendix lists some of the command-line interface (CLI) commands that appear when you enter the question mark (?) at the Cisco Metro Ethernet (ME) 3800X and ME 3600X switch prompt but are not supported in this release, either because they are not tested or because of switch hardware limitations. This is not a complete list. The unsupported commands are listed by software feature and command mode or they are listed by command mode under Other Unsupported Commands.

    Access Control List Commands, page C-2 Address Resolution Protocol (ARP) Commands, page C-2 Hot Standby Routing Protocol (HSRP) Commands, page C-2 IGMP Snooping Commands, page C-3 IP Multicast Routing Commands, page C-3 IP Unicast Routing Commands, page C-4 Multiprotocol Label Switching (MPLS) Commands, page C-6 Multicast Source Discovery Protocol (MSDP) Commands, page C-7 NetFlow Commands, page C-7 Quality of Service (QoS) Commands, page C-7 RADIUS Commands, page C-8 Simple Network Management Protocol (SNMP) Commands, page C-8 Spanning Tree Commands, page C-8 VLAN Commands, page C-9 Other Unsupported Commands, page C-9

    Cisco ME 3800X and ME 3600X Switch Software Configuration Guide OL-26702-01

    C-1

    Appendix C Access Control List Commands

    Unsupported Commands in Cisco IOS Release 15.2(2)S

    Access Control List Commands


    Privileged EXEC Mode
    access-enable [host] [timeout minutes] access-template clear access-template . show arp access-list

    Global Configuration Mode


    arp access-list access-list rate-limit acl-index {precedence | mask prec-mask} access-list dynamic extended

    Address Resolution Protocol (ARP) Commands


    Global Configuration Mode
    arp ip-address hardware-address smds arp ip-address hardware-address srp-a arp ip-address hardware-address srp-b

    Interface Configuration Mode


    arp probe

    Hot Standby Routing Protocol (HSRP) Commands


    Global Configuration Mode
    interface Async interface BVI interface Dialer interface Group-Async interface Lex interface Virtual-Template interface Virtual-Tokenring

    Cisco ME 3800X and ME 3600X Switch Software Configuration Guide

    C-2

    OL-26702-01

    Appendix C

    Unsupported Commands in Cisco IOS Release 15.2(2)S IGMP Snooping Commands

    IGMP Snooping Commands


    Global Configuration Mode
    ip igmp snooping source-only-learning

    IP Multicast Routing Commands


    Privileged EXEC Mode
    clear ip dvmrp route commands debug ip dvmrp commands The debug ip packet command displays packets received by the switch CPU. It does not display packets that are hardware-switched. The debug ip mcache command affects packets received by the switch CPU. It does not display packets that are hardware-switched. The debug ip mpacket [detail] [access-list-number [group-name-or-address] command affects only packets received by the switch CPU. Because most multicast packets are hardware-switched, use this command only when you know that the route will forward the packet to the CPU. debug ip pim atm show ip dvmrp route commands The show ip mcache command displays entries in the cache for those packets that are sent to the switch CPU. Because most multicast packets are switched in hardware without CPU involvement, you can use this command, but multicast packet information is not displayed. The show ip mpacket commands are supported but are only useful for packets received at the switch CPU. If the route is hardware-switched, the command has no effect because the CPU does not receive the packet and cannot display it.

    Global Configuration Mode


    All ip dvmrp commands ip multicast-routing vrf vrf-name ip pim accept-rp ip pim register-rate-limit

    Interface Configuration Mode


    All ip dvmrp commands ip igmp helper-address ip-address

    Cisco ME 3800X and ME 3600X Switch Software Configuration Guide OL-26702-01

    C-3

    Appendix C IP Unicast Routing Commands

    Unsupported Commands in Cisco IOS Release 15.2(2)S

    ip multicast helper-map {group-address | broadcast} {broadcast-address | multicast-address} extended-access-list-number ip multicast rate-limit {in | out} [video | whiteboard] [group-list access-list] [source-list access-list] kbps ip multicast ttl-threshold ttl-value (instead, use the ip multicast boundary access-list-number interface configuration command) ip pim nbma-mode

    IP Unicast Routing Commands


    Privileged EXEC or User EXEC Mode
    clear ip accounting [checkpoint] clear ip bgp address flap-statistics show cef [drop | not-cef-switched] show ip accounting [checkpoint] [output-packets | access-violations] show ip bgp dampened-paths show ip bgp inconsistent-as show ip bgp regexp regular expression show ipv6 (all)

    Global Configuration Mode


    ip accounting-list ip-address wildcard ip accounting-transits count ip cef traffic-statistics [load-interval seconds] [update-rate seconds]] ip flow-aggregation ip flow-cache ip flow-export ip gratuitous-arps ip local ip reflexive-list router iso-igrp router mobile router odr

    Cisco ME 3800X and ME 3600X Switch Software Configuration Guide

    C-4

    OL-26702-01

    Appendix C

    Unsupported Commands in Cisco IOS Release 15.2(2)S IP Unicast Routing Commands

    Interface Configuration Mode


    dampening ip accounting ip load-sharing [per-packet] ip mtu bytes ip ospf dead-interval minimal hello-multiplier multiplier ip unnumbered type number All ip security commands

    BGP Router Configuration Mode


    default-information originate neighbor advertise-map neighbor allowas-in neighbor default-originate neighbor description network backdoor table-map

    Route Map Configuration Mode


    match route-type for policy-based routing (PBR) set automatic-tag set dampening half-life reuse suppress max-suppress-time set default interface interface-id [interface-id.....] set interface interface-id [interface-id.....] set ip default next-hop ip-address [ip-address.....] set ip destination ip-address mask set ip precedence value set ip qos-group set metric-type internal set origin set metric-type internal

    VPN Configuration Mode


    All

    Cisco ME 3800X and ME 3600X Switch Software Configuration Guide OL-26702-01

    C-5

    Appendix C Multiprotocol Label Switching (MPLS) Commands

    Unsupported Commands in Cisco IOS Release 15.2(2)S

    Multiprotocol Label Switching (MPLS) Commands


    Privileged EXEC or User EXEC Mode
    debug ip rsvp hello [bfd | detail | stats] debug ip rsvp sso debug mpls traffic-eng exp debug mpls traffic-eng forwarding-adjacency debug mpls traffic-eng ha show ip rsvp fast-reroute show ip rsvp hello [instance | statistics] show mpls traffic-eng exp show mpls traffic-eng forwarding-adjacency

    Global Configuration Mode


    ip rsvp signalling hello {bfd | graceful-restart) mpls traffic-eng auto-bw mpls traffic-eng lsp

    Interface Configuration Mode


    Physical Interfaces
    ip rsvp bandwidth {mam | rdm} ip rsvp signalling hello [bfd | dscp | fast-reroute | graceful-restart | refresh | reroute] mpls traffic-eng srlg

    Tunnel Interfaces
    tunnel mpls traffic-eng auto-bw tunnel mpls traffic-eng backup-bw tunnel mpls traffic-eng exp tunnel mpls traffic-eng exp-bundle tunnel mpls traffic-eng forwarding-adjacency tunnel mpls traffic-eng path-option dynamic attributes tunnel mpls traffic-eng path-option explicit name attributes tunnel mpls traffic-eng path-selection

    Cisco ME 3800X and ME 3600X Switch Software Configuration Guide

    C-6

    OL-26702-01

    Appendix C

    Unsupported Commands in Cisco IOS Release 15.2(2)S Multicast Source Discovery Protocol (MSDP) Commands

    Routing Configuration Mode


    interface auto-template mpsl traffic-eng mesh-group (ISIS mode) mpsl traffic-eng multicast-intact (ISIS mode and OSPF mode) tunnel destination mesh-group

    Multicast Source Discovery Protocol (MSDP) Commands


    Privileged EXEC Mode
    show access-expression show exception show pm LINE show smf [interface-id] show subscriber-policy [policy-number] show template [template-name]

    Global Configuration Mode


    ip msdp default-peer ip-address | name [prefix-list list] (Because BGP/MBGP is not supported, use the ip msdp peer command instead of this command.)

    NetFlow Commands
    Global Configuration Mode
    ip flow-aggregation cache ip flow-cache entries

    Quality of Service (QoS) Commands


    Global Configuration Mode
    priority-list

    Cisco ME 3800X and ME 3600X Switch Software Configuration Guide OL-26702-01

    C-7

    Appendix C RADIUS Commands

    Unsupported Commands in Cisco IOS Release 15.2(2)S

    Interface Configuration Mode


    priority-group

    RADIUS Commands
    Global Configuration Mode
    aaa authentication feature default enable aaa authentication feature default line aaa nas port extended authentication command bounce-port ignore authentication command disable-port ignore radius-server attribute nas-port radius-server configure radius-server extended-portnames

    Simple Network Management Protocol (SNMP) Commands


    Global Configuration Mode
    snmp-server enable informs snmp-server ifindex persist

    Spanning Tree Commands


    Global Configuration Mode
    spanning-tree pathcost method {long | short} spanning-tree transmit hold-count

    Interface Configuration Mode


    spanning-tree stack-port

    Cisco ME 3800X and ME 3600X Switch Software Configuration Guide

    C-8

    OL-26702-01

    Appendix C

    Unsupported Commands in Cisco IOS Release 15.2(2)S VLAN Commands

    VLAN Commands
    Global Configuration Mode
    vlan internal allocation policy {ascending | descending}

    Global Configuration Mode


    vlan internal allocation policy {ascending | descending}

    VLAN Configuration Mode


    remote-span

    Other Unsupported Commands


    Privileged EXEC and User EXEC Mode
    All event manager commands renew ip dhcp snooping database test cable-diagnostics prbs verify

    Clear Commands
    All clear dot1x commands clear ip arp inspection All clear ip dhcp snooping commands All clear ipv6 commands

    Debug Commands
    All debug dot1x commands All debug ip dhcp snooping commands debug ip verify source packet All debug platform commands

    Cisco ME 3800X and ME 3600X Switch Software Configuration Guide OL-26702-01

    C-9

    Appendix C Other Unsupported Commands

    Unsupported Commands in Cisco IOS Release 15.2(2)S

    Show Commands
    show archive log show cable-diagnostics prbs All show dot1x commands show ip arp inspection All show ip dhcp snooping commands All show ip source binding commands show ip verify source All show ipv6 commands All show platform commands show table-map

    Global Configuration Mode


    All dot1x commands All event manager commands exception crashinfo errdisable detect cause dhcp-rate-limit errdisable recovery cause dhcp-rate-limit interface tunnel All ip arp inspection commands All ip dhcp snooping commands ip source binding ip sticky-arp All macro auto commands memory reserve critical service compress-config

    Interface Configuration Mode


    All dot1x commands All ip arp inspection commands All ip dhcp snooping commands ip sticky-arp ignore ip verify source [tracking | vlan] transmit-interface type number

    Cisco ME 3800X and ME 3600X Switch Software Configuration Guide

    C-10

    OL-26702-01

    You might also like