Exam 08 (22-23)

BIKING TECHNICAL VOCATIONAL HIGH SCHOOL
4TH QUARTER EXAMINATION
NAME: _______________________________YEAR AND SECTION: __________________ SCORE: ______
Directions: Read and understand the statement below. Encircle the letter that corresponds the correct answer.
1. Circulates through the engine and the radiator, absorbs the heat and uses the air passing through the radiator to cool
it down.
a. Oil b. coolant c. gasoline d. brake fluid
2. Reservoir of the in the cooling system of an engine.
a. Gas tank b. radiator c. resistor d. battery
3. Pressurized the coolant so that the coolant will circulates in the cooling system
a. Radiator b. fuel pump c. water pump d. thermostat
4. It will opens letting the hot coolant to circulates inside the engine
a. Fuel pump b. water pump c. thermostat d. radiator hose
5. The water passages inside an engine.
a. Water jackets b. radiator hose c. thermostat d. water pump
6. Releases the extra pressure by sending some coolant into the overflow tank.
a. Water jackets b. thermostat c. radiator cap d. water pump
7. Use as a connector between the radiator and the engine for the coolant to circulates.
a. Radiator hose b. radiator cablec. radiator cap d. water jackets
8. The process of getting the air inside the cooling system is called
a. Water jackets b. coolant mixing c. bleeding d. pumping
9. One of the major cause of engine overheating is
a. Coolant leakage b. wrong coolant filled c. no thermostat d. none of the above
10. The contaminants building up in the radiator that discolored the coolant and turns into rusty color because of oil.
a. bleeding b. fuel c. sludge d. rubber
11. Reservoir of oil in an engine.
a. radiator b. oil cooler c. dip stick d. oil pan
12. Pressurized the oil so that it can lubricate upper moving parts of an engine.
a. Oil pump b. dipstick c. oil cooler d. oil hole
13. Is the ability of oil to flow
a. Stability b. viscosity c. adaptability d. flow ability
14. This is used to verify if you have enough amount of oil on you engine.
a. Oil pump b. radiator c. oil hole d. dipstick
15. This will prevent any metal particles or dirt to flow in the lubricating system
a. Oil pump b. oil cooler c. oil filter d. oil pan
16. An oil passages in the lubricating system
a. Oil hole b. oil cooler c. oil pan d. dipstick
17. SAE means _____________.
a. Standard Assurance Equipment b. Safety Automotive Equipment
c. Seeking All Everything d. Society of Automotive Engineers
18. Helps the oil to cool down and extends it life
a. Oil cooler b. water cooler c. engine fan d. cooling system
19. What is the W in the oil description means? 20W 50.
a. weather b. watts c. welcome d. winter
20. Range of kilometers in which you should change oil.
.a.3000 – 3500 b. 4000-5000 c. 5000-10000 d. 10000- 15000
21. Have a needle-nose ends used for holding or picking small objects.
a. Wire stripper b. side cutting pliers c. long-nose pliers d. vise grip
22. Used to strip electrical wires in different sizes.
23. A specially designed pliers used for holding work pieces together.
24. Device for holding and bending pieces of metal.
a. Chisel b. bench vise c. file d. Electric drill
25. A tool for boring holes.
26. A hard steel tool use for smoothening metal.
27. An excellent tool for cutting bolt, tubing and light to fairly thick metal.
a. Tin snip b. hacksaw c. hammer d. puncher
28. A scissor shaped tool used for cutting thin sheets of metal.
29. Generally used for driving or striking work.
30. Used to cut or drive out a bolt or lock needle pin out of a hole.
31. A tool with an open-end on one side and box-end on the opposite side. Used in loosening and tightening bolts and
nuts.
a. Combination wrench b. spark plug wrench c. socket wrench d. tire wrench
32. A tubular-like tool with an enclosed end used for heavy application for loosening and tightening bolts and nuts.
33. A socket-like wrench intended for removing spark plugs
34. A cross-like or sometimes L-shaped piece of round bar used to remove the wheels of the vehicle.
35. Has a flat tip at the end and used in a single groove screws.
a. Philip screw driver b. scriber c. torque wrench d. flat screw driver
36. Has a cross-like tip at the end used in a cross groove head of the screws.
37. A thin steel rod with pointed tip on its end and used for marking fine lines.
38. A special service tool for measuring the twisting force applied when tightening bolts and nuts.
39. A tool used in measuring the diameter of a circular work.
a. Steel rule b. caliper c. metal tape measure d. feeler gauge
40. A thin strip of metal with different thickness used to measure or set gap and clearance between parts of mechanism.
a. Steel rule b. caliper c. metal tape measure d. feeler gauge
GOD BLESS…………………..

Exam 08 (22-23)

Uploaded by

Copyright:

Available Formats

Exam 08 (22-23)

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Exam 08 (22-23)

Uploaded by

Copyright:

Available Formats

BIKING TECHNICAL VOCATIONAL HIGH SCHOOL

4TH QUARTER EXAMINATION

NAME: ___________________YEAR AND SECTION: SCORE:

You might also like