‫جتلس‬ ‫فوج ماكينه ر‬

‫ي‬ ‫برمجه انفرتر‬

‫ر‬
‫البارمت‬ ‫ر‬
‫البارمت رشح‬ ‫قيمه‬ ‫ر‬
‫البارمت‬ ‫رقم‬
‫طريقه ادخال الرسعات‬ 0 F01
RPM Maximum Speed ‫اقص شعه للماكينه‬ ‫ي‬ rpm… F03
(RPM) Rated Speed ‫ شعه الماكينه‬rpm… F04
Rated Voltage ‫فولت الماكينه‬ …V F05
Acceleration time ‫ال الرسعه القصوي‬
‫زمن الصعود من الصفر ي‬ 2.5 F07
Deceleration time ‫ال الصفر‬
‫زمن الهبوط من الرسعه القصوي ي‬ 2.5 F08
Starting Speed 0 F23
(Holding time) 0.6 F24
Stop Speed 0 F25
(Carrier frequency) 15 F26
Control Mode (GEARLESS=1) (GEAR=2) 1 F42
Select multistep speed 1 SS1 FAST 0 E01
Select multistep speed 2 SS2 SLW 1 E02
Select multistep speed 4 SS4 INSPECATION 2 E03
Reset alarm RST 8 E04
Enable coast-to-stop BX 7 E07
Enable battery operation BATRY 63 E08
Acceleration/DecelerationTime 7 1 E14
3: FWD , REV / SS1 , SS2 , SS4 3 E18
12 (1012): MAIN CONTACTOR control SW52-2 (Y1) 12 E20
Speed detected FDT (Y3) 2 E22
Current detected(Y4) 37 E23
Brake control (Y5) 57 E24
FAST SPEED (X1) ... rpm C05
UPS SPEED (X8) …. rpm C06
SLOW SPEED (X3) …. rpm C08
INSPECTION SPEED (X2) …. rpm C10
UNIT OF SPEED (rpm) 0 C21
NUM OF POLE ‫عدد البوالت‬ ….P P01
KW IN MACHINE ‫قدره الماكينه‬ …KW P02
A IN MACHINE ‫امبت الماكينه‬
‫ر‬ …A P03
20---40% P03 noload current of the machine
…A P06
it could be measured using Auto tuning p04 set to 2
4 (1313)or 5(1387) (Encoder type) IN GEARLESS ONLY 4 L1
Encoder pulse.....P/R pulse per revolution 2048 L2
TUNE 1or 3 l3
S-Curve setting1 20% L19
S-Curve setting2 20% L20
S-Curve setting3 20% L21
S-Curve setting4 20% L22
S-Curve setting5 20% L23
S-Curve setting6 20% L24
S-Curve setting7 20% L25
S-Curve setting8 20% L26
S-Curve setting9 20% L27
S-Curve setting10 20% L28
ASR (auto speed regulator) IN HIGH SPEED 2 l36
ASR IN LOW SPEED 2 l38
Brake ON delay time 0.2 L82
Brake OFF delay time 0.3 L83
Main contactors start-up delay time 0.2 L85
Main contactors OFF delay time 1 L86
‫جت‬
‫فوج ماكينه ر‬
‫ي‬ ‫برمجه انفرتر‬
‫طريقه ادخال الرسعات‬ F01
RPM Maximum Speed ‫اقص شعه للماكينه‬ ‫ي‬ F03
(HZ) Rated Speed ‫شعه الماكينه‬ F04
Rated Voltage ‫فولت الماكينه‬ F05
Acceleration time ‫ال الرسعه القصوي‬‫زمن الصعود من الصفر ي‬ F07
Deceleration time ‫ال الصفر‬
‫ي‬ ‫القصوي‬ ‫زمن الهبوط من الرسعه‬ F08
Starting Speed F23
(Holding time) F24
Stop Speed F25
(Carrier frequency) F26
Control Mode (GEAR=2) F42
Select multistep speed 1 SS1 FAST E01
Select multistep speed 2 SS2 SLW E02
Select multistep speed 4 SS4 INSPECATION E03
Reset alarm RST E04
Enable coast-to-stop BX E07
Enable battery operation BATRY E08
Acceleration/DecelerationTime 7 E14
3: FWD , REV / SS1 , SS2 , SS4 E18
12 (1012): MAIN CONTACTOR control SW52-2 (Y1) E20
Speed detected FDT (Y3) E22
Current detected(Y4) E23
Brake control (Y5) E24
FAST SPEED (X1) C05
UPS SPEED (X8) C06
SLOW SPEED (X3) C08
INSPECTION SPEED (X2) C10
UNIT OF SPEED (rpm) C21
NUM OF POLE ‫عدد البوالت‬ P01
KW IN MACHINE ‫قدره الماكينه‬ P02
A IN MACHINE ‫امبت الماكينه‬
‫ر‬ P03
20---40% P03 noload current of the machine
P06
it could be measured using Auto tuning p04 set to 2
S-Curve setting1 L19
S-Curve setting2 L20
S-Curve setting3 L21
S-Curve setting4 L22
S-Curve setting5 L23
S-Curve setting6 L24
S-Curve setting7 L25
S-Curve setting8 L26
S-Curve setting9 L27
S-Curve setting10 L28
ASR (auto speed regulator) IN HIGH SPEED l36
ASR IN LOW SPEED l38
Brake ON delay time L82
Brake OFF delay time L83
Main contactors start-up delay time L85
Main contactors OFF delay time L86