PHYSICS

NANO-MYCLASSROOM
CIRCULAR MOTION

CIRCULAR MOTION :
When a particle moves in a plane such that its distance from a fixed (or moving) point remains constant,
then its motion is known as circular motion with respect to that fixed (or moving) point. The fixed point is
called centre, and the distance of particle from it is called radius.

1. KINEMATICS OF CIRCULAR MOTION :

1.1 Variables of Motion :
(a) Angular Position :
To decide the angular position of a point in space we need to specify (i) origin and (ii) reference line.
The angle made by the position vector w.r.t. origin, with the reference line is called angular position.
Clearly angular position depends on the choice of the origin as well as the reference line.
Y
Circular motion is a two dimensional motion or motion in a plane.
Suppose a particle P is moving in a circle of radius r and centre O. P'


P
The angular position of the particle P at a given instant may be
described by the angle  between OP and OX. This angle  is  X
O r
called the angular position of the particle.

(b) Angular Displacement :

Definition: Angle through which the position vector of the moving particle rotates in a given time
interval is called its angular displacement. Angular displacement depends on origin, but it does not
depends on the reference line. As the particle moves on above circle its angular position  changes.
Suppose the point rotates through an angle  in time t, then  is angular
displacement.

 Important points :
 Angular displacement is a dimensionless quantity. Its SI unit is radian, some other units are degree
and revolution
2 rad = 360° = 1 rev
 Infinitesimally small angular displacement is a vector quantity, but finite angular displacement is a
scalar, because while the addition of the Infinitesimally small angular displacements is commuta-
tive, addition of finite angular displacement is not.
d1  d 2  d 2  d1 1   2   2  1
   
but

 Direction of small angular displacement is decided by right hand thumb rule. When the fingers are
directed along the motion of the point then thumb will represents the direction of angular
displacement.

(c ) Angular Velocity 
(i) Average Angular Velocity

av =
Angular displaceme nt
Total time taken
 2  1 
av  
t 2  t1 t

where  1 and  2 are angular position of the particle at time t 1 and t 2 . Since angular
displacement is a scalar, average angular velocity is also a scalar.

"manishkumarphysics.in" 1
 PHYSICS
(ii) Instantaneous Angular Velocity
It is the limit of average angular velocity as t approaches zero. i.e.


 
 = t 0
 d
t
lim =
dt

Since infinitesimally small angular displacement d is a vector quantity, instantaneous angular velocity  is


also a vector, whose direction is given by right hand thumb rule.

 Important points :
 Angular velocity has dimension of [T-1] and SI unit rad/s.
 For a rigid body, as all points will rotate through same angle in same time, angular velocity is a
characteristic of the body as a whole, e.g., angular velocity of all points of earth about earth’s axis is
(2/24) rad/hr.


2 n
If a body makes ‘n’ rotations in ‘t’ seconds then average angular velocity in radian per second will be

 av 
t
If T is the period and ‘f’ the frequency of uniform circular motion

av =
2
= 2f
T

Example 1. If angular displacement of a particle is given by   a  bt  ct 2 , then find its angular velocity..

d
Solution :   b  2ct
dt

Example 2. Is the angular velocity of rotation of hour hand of a watch greater or smaller than the angular velocity
of Earth’s rotation about its own axis ?
Solution : Hour hand completes one rotation in 12 hours while Earth completes one rotation in 24 hours. So,

2 
angular velocity of hour hand is double the angular velocity of Earth.    .
 T 

(d) Angular Acceleration  

(i) Average Angular Acceleration :
Let 1 and 2 be the instantaneous angular speeds at times t1 and t2 respectively, then the
average angular acceleration av is defined as

  1 
  
 av  2 

t 2  t1 t

(ii) Instantaneous Angular Acceleration :

It is the limit of average angular acceleration as t approaches zero, i.e.,

 d 
 
  lim 

t  0 t dt

d d2  d
  
since   ,   =


 d  
d
= , Also
dt dt dt 2

"manishkumarphysics.in" 2
 PHYSICS
 Important points :
 Both average and instantaneous angular acceleration are axial vectors with dimension [T-2] and unit
rad/s2.
 If  = 0, circular motion is said to be uniform.

1.2 Motion with constant angular velocity

 = t ,  = 0

1.3 Motion with constant angular acceleration

0  Initial angular velocity
  Final angular velocity
  Constant angular acceleration
  Angular displacement
Circular motion with constant angular acceleration is analogous to one dimensional translational motion with

 = 0 + t
constant acceleration. Hence even here equation of motion have same form.

 = 0t + t
1 2
2
2 = 02 + 2 

   0 
=   t
 2 


nth = 0 + ( – n-1)
2 n

2. RELATION BETWEEN SPEED AND ANGULAR VELOCITY :

v   r
  

Here, v is velocity of the particle,  is angular velocity about centre of circular motion and ‘ r ’ is position of
  

particle w.r.t. center of circular motion.

Since   r
 

v =  r for circular motion.

Example 3. A particle is moving with constant speed in a circular path. Find the ratio of average velocity to its


instantaneous velocity when the particle describes an angle  =
2

 R R
Time taken to describe angle , t =

Solution : = =
v 2v

Total displaceme nt 2R 2 2
R / 2v 
Average velocity = = = v
Total time
Instantaneous velocity = v

2 2

The ratio of average velocity to its instantaneous velocity = Ans.

Example 4. A fan is rotating with angular velocity 100 rev/sec. Then it is switched off. It takes 5 minutes to stop.
(a) Find the total number of revolution made before it stops. (Assume uniform angular retardation)
(b) Find the value of angular retardation (c) Find the average angular velocity during this interval.

"manishkumarphysics.in" 3
 PHYSICS

   0   100  0 
(a)  =   t =   × 5× 60 = 15000 revolution.
 2   2 
Solution :

(b)  = 0 + t  0 = 100 –  ( 5 × 60)   =

1
rev./sec2
3

(c) av 
Total Angle of Rotation 15000
50  60
= = 50 rev./sec.
Total time taken

3. RELATIVE ANGULAR VELOCITY

Just as velocities are always relative, similarly angular velocity is also always relative. There is no such thing as
absolute angular velocity. Angular velocity is defined with respect to origin, the point from which the position
vector of the moving particle is drawn.
 Consider a particle P moving along a circular path shown in the figure given below
Here angular velocity of the particle P w.r.t. ‘O’ and ‘A’ will be different

Angular velocity of a particle P w.r.t. O, PO =

d
dt

Angular velocity of a particle P w.r.t. A, PA =

d
dt
Definition :
Angular velocity of a particle ‘A’ with respect to the other moving particle ‘B’ is the rate at which position
vector of ‘A’ with respect to ‘B’ rotates at that instant. (or it is simply, angular velocity of A with origin fixed at
B). Angular velocity of A w.r.t. B, AB is mathematically define as

AB =
Component of relative velocity of A w.r.t. B, perpendicular to line ( VAB ) 
=
seperation between A and B rAB

 Important points:
 If two particles are moving on two different concentric circles with different
velocities then angular velocity of B as observed by A will depend on
their positions and velocities. Consider the case when A and B are
closest to each other moving in same direction as shown in figure. In
this situation
 (VAB) |= vB  v A
Separation between A and B is rBA = rB – rA
vB  v A
AB =
( VAB ) 
rB  rA
so, =
rAB

 If two particles are moving on the same circle or different coplanar concentric circles in same direc-
tion with different uniform angular speed A and B respectively, the rate of change of angle between

OA and OB is B
B

 
A
A
=B – A
d
O O Initial line
dt Initial line

So the time taken by one to complete one revolution around O w.r.t. the other

2 2
T   1 2
TT
rel 2  1 T1  T2

"manishkumarphysics.in" 4
 PHYSICS

 B – A is rate of change of angle between OA and OB . This is not angular velocity of B w.r.t. A.
(Which is rate at which line AB rotates)

Example 5. Find the angular velocity of A with respect to B in the figure given below:

1
Solution : Angular velocity of A with respect to B ;

AB =
( VAB )  A
VA
rAB

VA
VB
 (VAB) = VA sin 1  VB sin  2 2

si
r

n
1


VB
sin
rAB = r B


v A sin 1  v B sin  2

2
AB =
r

Example 6. Find the time period of meeting of minute hand and second hand of a clock.

min = rad/min. , sec =

2 2
Solution : Ref. line rad/min
60 1
sec min = 2 (for second and minute hand to meet again)
(sec – min) t = 2

 t =
60
2(1 – 1/60) t = 2 min.
59

Example 7. Two particle A and B move on a circle. Initially Particle A and B are diagonally opposite to each other.
Particle A move with angular velocity  rad/sec. , angular acceleration /2 rad/sec2 and particle B
moves with constant angular velocity 2 rad/sec. Find the time after which both the particle A and B
will collide.
Solution : Suppose angle between OA and OB = 
then, rate of change of ,
 = B– A2 –  = rad/sec


  B – A = – rad/sec2
2
If angular displacement is 

   t  t
1  2
2
for A and B to collide angular displacement  = 

1
  = t +   t2  
2 2 
t2 – 4t + 4 = 0 t = 2 sec. Ans.

"manishkumarphysics.in" 5
 PHYSICS
Example 8. A particle is moving with constant speed in a circle as shown, find the angular velocity of the particle
A with respect to fixed point B and C if angular velocity with respect to O is .

Angular velocity of A with respect to O is ; AO = =

( v AO )  v
Solution : =
rAO r

 ( v AC )  
 AB = AC =
( v AB )  v v
= = and rAC = =
rAB 2r 2 3r 3

Example 9. Particles A and B move with constant and equal speeds in a circle as
shown, find the angular velocity of the particle A with respect to B, if
angular velocity of particle A w.r.t. O is .

Angular velocity of A with respect to O is ; AO = =

( v AO )  v
Solution : =
rAO r

AB = 
( v AB ) 
Now, vAB = 2v,
rAB
since vAB is perpendicular to rAB,

 (vAB) = vAB = 2v ;rAB = 2r  AB = =

( v AB )  2v
=
rAB 2r

Example 10. Find angular velocity of A with respect to O at the instant shown in the figure.

Solution : Angular velocity of A with respect to O is ;

AO =
( v AO ) 
rAO

v
vAO = v, (vAO) =
2

rAO = d 2

AO =
( v AO )  v/ 2 v
= =
rAO d 2 2d

"manishkumarphysics.in" 6
 PHYSICS
4. RADIAL AND TANGENTIAL ACCELERATION
There are two types of acceleration in circular motion ; Tangential acceleration and centripetal acceleration.
(a) Tangential acceleration :-
Component of acceleration directed along tangent of circle is called tangential acceleration. It is
responsible for changing the speed of the particle. It is defined as,

dv d| v |
at = = = Rate of change of speed.
dt dt
at = r

 IMPORTANT POINT
In vector form a t =   r
  
(i)
(ii) If tangential acceleration is directed in direction of velocity then the speed of the particle increases.
(iii) If tangential acceleration is directed opposite to velocity then the speed of the particle decreases.

(b) Centripetal acceleration :-

It is responsible for change in direction of velocity. In circular motion, there is always a centripetal
acceleration.
Centripetal acceleration is always variable because it changes in direction.
Centripetal acceleration is also called radial acceleration or normal acceleration.

(c) Total acceleration :-

Total acceleration is vector sum of centripetal acceleration and tangential acceleration.

= ar  a t

a
 dv  


dt

a= a t2  ar2

tan  = a
ar
t

 IMPORTANT POINT
(i) Differentiation of speed gives tangential acceleration.

(ii) Differentiation of velocity ( v ) gives total acceleration.
  
dv d| v | dv
(iii) & are not same physical quantity.. is the magnitude of rate of change of velocity, i.e.
dt dt dt

d| v |
magnitude of total acceleration and is a rate of change of speed, i.e. tangential acceleration.
dt

4.1 Calculation of centripetal acceleration :

Consider a particle which moves in a circle with constant speed v as shown in figure.

 change in velocity between the point A and B is ;

  
 v = vB  v A

Magnitude of change in velocity.

"manishkumarphysics.in" 7
 PHYSICS

v  v B  v A  v B2  v 2A  2v A v B cos (   )
  

(vA = vB = v, since speed is same)

 
 | v | = 2v sin
2
Distance travelled by particle between A and B = r

t =
r
Hence time taken,
v

v 2v sin  / 2 v 2 2 sin  / 2


t r / v 
Net acceleration , anet = =
r

If t 0, then  is small, sin (/2) = /2

v
 
 
dv v2
t 0 t
lim
dt r

v2 dv
i.e. net acceleration is but speed is constant so that tangential acceleration, at = = 0.
r dt

 anet = ar =
v2
r
** Through we have derived the formula of centripetal acceleration under condition of constant speed, the
same formula is applicable even when speed is variable.

 IMPORTANT POINT
In vector form a c    v
  

Example 11. The speed of a particle traveling in a circle of radius 20 cm increases uniformly from 6.0 m/s to 8.0
m/s in 4.0 s, find the angular acceleration.
Solution : Since speed increases uniformly, average tangential acceleration is equal to instantaneous tangen-

 The instantaneous tangential acceleration is given by

tial acceleration

v 2  v1
t 2  t1
dv
at = =
dt

8 .0  6 . 0
= m/s2 = 0.5 m/s2.
4 .0
The angular acceleration is  = at / r
0 .5 m / s 2
= = 2.5 rad/s2.
20 cm
Example 12. A particle is moving in a circle of radius 10 cm with uniform speed completing the circle in 4s, find the
magnitude of its acceleration.
Solution : The distance covered in completing the circle is 2  r = 2  × 10 cm. The linear speed is

2 10 cm
v = 2  r/t = = 5  cm/s.
4s

(5 cm / s) 2
= 2.5  2 cm/s2.
v2
The acceleration is a = =
r 10 cm

"manishkumarphysics.in" 8
 PHYSICS
Example 13. A particle moves in a circle of radius 2.0 cm at a speed given by v = 4t, where v is in cm/s and t is in
seconds.
(a) Find the tangential acceleration at t = 1s.
(b) Find total acceleration at t = 1s.
Solution : (a) Tangential acceleration

dv d
at = or at = (4t) = 4 cm/s2
dt dt

 a 2t  a C2  ( 4)2  (8)2  4 5 cm/s2

v2 ( 4) 2
aC = = = 8 cm/s2 a=
R 2
Example 14. A particle begins to move with a tangential acceleration of constant magnitude 0.6 m/s2 in a circular
path. If it slips when its total acceleration becomes 1 m/s2, Find the angle through which it would
have turned before it starts to slip.

Solution : aNet = a 2t  a c2  2 = 2 + 2

 = 0 2 = 2
2R = 2 (R)
so

ac = 2R = 2at

1= 0.36  (1.2  )2  1 – 0.36 = (1.2 )2

   
0.8 2
radian Ans.
1.2 3

5. DYNAMICS OF CIRCULAR MOTION :

If there is no force acting on a body it will move in a straight line (with constant speed). Hence if a body is
moving in a circular path or any curved path, there must be some force acting on the body.
If speed of body is constant, the net force acting on the body is along the inside normal to the path of the
body and it is called centripetal force.

= m 2 r
mv 2
Centripetal force (Fc) = mac =
r
However if speed of the body varies then, in addition to above centripetal force which acts along inside
normal, there is also a force acting along the tangent of the path of the body which is called tangential force.

=Mr ; where  is the angular acceleration

dv
Tangential force (Ft) = Mat = M
dt

 IMPORTANT POINT

mv 2
Remember is not a force itself. It is just the value of the net force acting along the inside normal which
r
is responsible for circular motion. This force may be friction, normal, tension, spring force, gravitational force
or a combination of them.
So to solve any problem in uniform circular motion we identify all the forces acting along the normal (towards

mv 2
center), calculate their resultant and equate it to .
r
If circular motion is non uniform then in addition to above step we also identify all the forces acting along the

mdv md | v |
tangent to the circular path, calculate their resultant and equate it to or .
dt dt

"manishkumarphysics.in" 9
 PHYSICS
6. CIRCULAR MOTION IN HORIZONTAL PLANE :

Example 15. A block of mass 2kg is tied to a string of length 2m, the other end of which is fixed. The block is
moved on a smooth horizontal table with constant speed 5 m/s. Find the tension in the string.

Solution :

here centripetal force is provided by tension.

mv 2 2  52
T= = = 25 N
r 2

Example 16. A block of mass m moves with speed v against a smooth, fixed vertical circular groove of radius r
kept on smooth horizontal surface.

Find :
(i) normal reaction of the floor on the block.
(ii) normal reaction of the vertical wall on the block.
Solution : Here centripetal force is provided by normal reaction of vertical wall.
(i) normal reaction of floor NF = mg

mv 2
(ii) normal reaction of vertical wall NW = .
r

Example 17. A block of mass m is kept on the edge of a horizontal turn table of radius R, which is rotating with
constant angular velocity  (along with the block) about its axis. If coefficient of friction is , find the
friction force between block and table
Solution : Here centripetal force is provided by friction force.
Friction force = centripetal force = m2R

Example 18. Consider a conical pendulum having bob of mass m is suspended from a ceiling through a string of
length L. The bob moves in a horizontal circle of radius r. Find (a) the angular speed of the bob and
(b) the tension in the string.
Solution : The situation is shown in figure. The angle  made by
the string with the vertical is given by

L2  r 2
sin  = r / L, cos  = h/L = ...(i)
L
The forces on the particle are
(a) the tension T along the string and
(b) the weight mg vertically downward.

The particle is moving in a circle with a constant speed v.

Thus , the radial acceleration towards the centre has magni-
tude v2 / r. Resolving the forces along the radial direction and

"manishkumarphysics.in" 10
 PHYSICS
applying Newton’s second law,
Tsin  = m(v2 / r) ....(ii)
As there is no acceleration in vertical direction, we have from Newton’s law,
Tcos  = mg .....(iii)
Dividing (ii) by (iii),

tan  rg tan 
v2
= or, v =
rg

g tan 
g
 = =
v g g
L cos  r )
1
= = = 2 2 2
Ans.
r r h (L

mg mgL
cos 
And from (iii), T = = Ans.
r )
1
2 2 2
(L

Example 19. A block of mass m is tied to a spring of spring constant k , natural length , and the other end of
spring is fixed at O. If the block moves in a circular path on a smooth horizontal surface with
constant angular velocity  , find tension in the spring.

Solution : Assume extension in the spring is x

Here centripetal force is provided by spring force.
Centripetal force, kx = m2( + x)

m 2 

k  m 2
x=

therefore,

km 2 
k  m 2
Tension = kx = Ans.

Example 20. A string breaks under a load of 50 kg. A mass of 1 kg is attached to one end of the string 10 m long
and is rotated in horizontal circle. Calculate the greatest number of revolutions that the mass can

 = 2n ,
make in one second without breaking the string.
Solution :
Tmax = 500 N, r = L sin
2


Tsin = m r
T = m2 L
 Tmax = m max
2
L
 Tmax = m(2nmax)2 L

1 Tmax 1 500 50
2 mL 2 1 10 2
nmax = = = revolution per second. Ans.

Example 21. A boy whirls a stone in a horizontal circle of radius 2 m and at height 4.9 m above level ground. The
string breaks, and the stone files off horizontally and strikes the ground at a point which is 10 m
away from the point on the ground directly below the point where the string had broken. What is the
magnitude of the centripetal acceleration of the stone while in circular motion? (g = 9.8 m/s2)

"manishkumarphysics.in" 11
 PHYSICS

2  4.9
 1s
2h
Solution : t= g 9.8

10
v= = 10 m/s
t

v2
a= = 50 m/s2
R

Example 22. A hemispherical bowl of radius R is rotating about its axis of symmetry which is kept vertical. A small
ball kept in the bowl rotates with the bowl without slipping on its smooth surface and the angle made
by the radius through the ball with the vertical is . Find the angular speed at which the bowl is
rotating.
Solution : Let  be the angular speed of rotation of the bowl. Two force are acting on the ball.
1. Normal reaction N 2. weight mg
The ball is rotating in a circle of radius r (= R sin ) with centre
at A at an angular speed . Thus,
N sin  = mr2 = mR2 sin 

N = mR2 ....(i)
N cos  = mg

and ...(ii)
R
Dividing Eqs. (i) by (ii),
2R
N


1 A

cos 
r
we get
g mg

 ω
g
R cosα

7. RADIUS OF CURVATURE
Any curved path can be assumed to be made of infinite circular arcs. Radius of curvature at a point is the
radius of the circular arc at a particular point which fits the curve at that point.


If R is radius of the circular arc at a given point P, where velocity is v , then centripetal force at that point is,


mv 2 mv 2
Fc = R=
R FC
Now centripetal force Fc is simply the component of force perpendicular to velocity (let us say F).

 R= 
mv 2 v2
R=
F a
Where, aComponent of acceleration perpendicular to velocity.

"manishkumarphysics.in" 12
 PHYSICS
 If a particle moves in a trajectory given by y = f(x) then radius of curvature at any point (x, y) of the trajectory

  dy  2 
3/2

1    
  dx  
is given by  R =
d2 y
dx 2

Example 23. A particle of mass m is projected with speed u at an angle  with the horizontal. Find the radius of
curvature of the path traced out by the particle at the point of projection and also at the highest point
of trajectory.
Solution : at point of projection
u
mv 2 mu 2 
mg cos 
R= =

F

u2 F=mgcos
g cos 
R= Ans. F = mg
at highest point
v2 u 2 cos 2 
a = g , v = ucos : R= = Ans.
a g
Example 24. A particle moves along the plane trajectory y(x) with constant speed v. Find the radius of curvature of
the trajectory at the point x = 0 if the trajectory has the form of a parabola y = ax2 where ‘a’ is a
positive constant.
Solution : If the equation of the trajectory of a particle is given we can find the radius of trajectory of the
instantaneous circle by using the formula

  dy  2 
3/2

1    
  dx  
R=
d2 y
dx 2


dy d2 y
As ; y = ax2 = 2ax = 0 (at x = 0) and = 2a
dx dx 2
Now radius of trajectory is given by
[1  0]3 / 2 1
R= =
2a 2a
v2
Aliter : This problem can also be solved by using the formula : R = . y = ax2 ,
a
dy dx
differentiate with respect to time = 2ax ....(1)
dt dt
dy
at x = 0, vy = = 0 hence vx = v
dt
since vx is constant, ax = 0

 dx 
2a 
2
d2 y d2 x
 dt 
Now, differentiate (1) with respect to time 2 = 2ax 2 +
dt dt
at x = 0, vx = v
net acceleration, a = ay = 2av2 (since ax = 0)
this acceleration is perpendicular to velocity (vx)
Hence it is equal to centripetal acceleration


v2 v2 1
R= = Ans.
a 2av 2 2a

"manishkumarphysics.in" 13
 PHYSICS

8. MOTION IN A VERTICAL CIRCLE :

Let us consider the motion of a point mass tied to a string
of length  and whirled in a vertical circle. If at any time
the body is at angular position , as shown in the figure,
the forces acting on it are tension T in the string along the
radius towards the center and the weight of the body mg
acting vertically down wards.
Applying Newton’s law along radial direction

T – mg cos  = m.ac =
mv 2

+ mg cos 
mv 2
or T= .....(1)

The point mass will complete the circle only and only if tension is never zero (except momentarily, if at all) if
tension becomes zero at any point, string will go slack and subsequently, the only force acting on the body
is gravity. Hence its subsequent motion will be similar to that of a projectile.
From equation ...(1), it is evident that tension decreases with increase in  because cos  is a decreasing
function and v decreases with height. Hence tension is minimum at the top most point. i.e. Tmin = Ttopmost.
T > 0 at all points.  Tmin > 0.
However if tension is momentarily zero at highest point the body
would still be able to complete the circle.
Hence condition for completing the circle (or looping the loop) is
Tmin  0 or Ttop  0.

mv 2top
Ttop + mg = ...............(2)

Equation...(2) could also be obtained by putting  =  in equation ..(1).
For looping the loop, Ttop  0.

  mg  vtop 
mv 2top
g .................(3)


Condition for looping the loop is vtop  g .

If speed at the lowest point is u, then from conservation of mechanical energy between lowest point and top
most point.

1 1
mu2 = m v 2top + mg . 2
2 2

using equation ..(3) for vtop we get u  5g 

i.e., for looping the loop, velocity at lowest point must be  5g  .

 If velocity at lowest point is just enough for looping the loop, value of various quantities. (True for a point mass
attached to a string or a mass moving on a smooth vertical circular track.)

"manishkumarphysics.in" 14
 PHYSICS

P.E. = 0

By energy conservation, v =
2
T–mg =
could also be obtained by

anet = 5 g anet = g 10

C
v
aC
T=0
O aC = g
Ref.line at = 0

Fig. (3)

by energy conservation
+

A B,D C P( general po int)

1 Velocity 5g 3g g g(3  2 cos )
2 Tension 6mg 3mg 0 3mg(1  cos )
3 Potential Energy 0 mg 2mg mg (1  cos )
4 Radial acceleration 5g 3g g g(3  2 cos )
5 Tangential acceleration 0 g 0 g sin 

Note :- From above table we can see , Tbottom – Ttop = TC – TA = 6 mg , this difference in tension remain same even

if V > 5g

Example 25. Find minimum speed at A so that the ball can reach at point B as

v = 0 simultaneously at  = 90º.
shown in figure. Also discuss the motion of particle when T = 0,

Solution : From energy conservation

1
mv 2A + 0 = 0 + mg (for minimum speed vB = 0)
2
vmin = 2 g
at the position B, v = 0 and T = 0 (putting vB = 0 or  = 90º , in equation ............(1) )
ball will return back, motion is oscillatory

"manishkumarphysics.in" 15
 PHYSICS

8.1. CONDITION FOR OSCILLATION OR LEAVING THE CIRCLE :

In case of non uniform circular motion in a vertical plane if velocity of body

at lowest point is lesser than 5g , the particle will not complete the
circle in vertical plane. In this case, the motion of the point mass which
depend on ‘whether tension becomes zero before speed becomes zero or
vice versa.

Case  (Speed becomes zero before tension)

In this case the ball never rises above the level of the center O i.e. the body
is confined to move within C and B, ( |  | < 90° ) for this the speed at A,

v< 2g (as proved in above example)

In this case tension cannot be zero, since a component of gravity acts
radially outwards.
Hence the string will not go slack, and the ball will reverse back as soon as
its speed becomes zero.
Its motion will be oscillatory motion.
Case  (Tension becomes zero before speed)

In this case the ball rises above the level of center O i.e. it goes beyond point B ( > 90°) for this v > 2g
(as proved in above example)

In this case a component of gravity will always act towards center,

hence centripetal acceleration or speed will remain nonzero. Hence
tension becomes zero first.
As soon as, Tension becomes zero at any point, string will go
slack and subsequently, the only force acting on the body is
gravity. Hence its subsequent motion will be similar to that of a
projectile. In this case motion is a combination of circular and
projectile motion.

8.2 CONDITION FOR LOOPING THE LOOP IN SOME OTHER CASES

Case 1 : A mass moving on a smooth vertical circular track.

Case 2 : A particle attached to a light rod rotated in vertical circle.

Condition for just looping the loop, velocity v = 0 at highest point (even if tension is zero, rod won’t slack,
and a compressive force can appear in the rod).
By energy conservation,
velocity at lowest point = 4g

"manishkumarphysics.in" 16
 PHYSICS

Vmin  4 g  (for completing the circle)

Case 3 : A bead attached to a ring and rotated.

Condition for just looping the loop, velocity v = 0 at highest point (even if normal is zero, the bead will not lose
contact with the track, normal can act radially outward).
By energy conservation,
velocity at lowest point = 4g

Vmin  4g (for completing the circle)

Case 4 : A block rotated between smooth surfaces of a pipe.

Condition for just looping the loop, velocity v = 0 at highest point (even if normal is zero, the bead will not lose
contact with the track, normal can act radially outward).
By energy conservation,
velocity at lowest point = 4g

Vmin  4g (for completing the circle)

Example 26. If a particle of mass M is tied to a light inextensible string fixed at point P
and particle is projected at A with velocity VA= 4gL as shown. Find :
(i) velocity at points B and C
(ii) tension in the string at B and C
Assume particle is projected in the vertical plane.
Solution : VB = 2gL (from energy conservation)

VC = 6gL

MvB2
TB + Mg =
L
TB = Mg

Mv C2
TC – Mg =
L
TC = 7Mg (where M  Mass of the particle)

Example 27. Two point mass m are connected the light rod of length  and it is free to rotate in
vertical plane as shown. Calculate the minimum horizontal velocity is given to mass
so that it completes the circular motion in vertical lane.

Solution : Here tension in the rod at the top most point of circle can be zero or negative for
completing the loop. So velocity at the top most point is zero.
From energy conservation

 v=
2
1 1 v 48g
mv 2 + m = mg(2) + mg(4) + 0 Ans.
2 2 4 5

Example 28. You may have seen in a circus a motorcyclist driving in vertical loops inside a ‘death well’ (a hollow
spherical chamber with holes, so that the cyclist does not drop down when he is at the uppermost
point, with no support from below. What is the minimum speed required at the uppermost position to
perform a vertical loop if the radius of the chamber is 25 m?
Solution : When the motorcyclist is at the highest point of the death-well, the normal reaction R on the motor-
cyclist by the ceiling of the chamber acts downwards. His weight mg also act downwards.

 
mv 2
Fnet = mac R + mg =
r

"manishkumarphysics.in" 17
 PHYSICS
Here v is the speed of the motorcyclist and m is the mass of the motorcyclist (including the mass of
the motor cycle). Because of the balancing of the forces, the motorcyclist does not fall down.
The minimum speed required to perform a vertical loop is given by equation (1) when R = 0.

 9.8  25 m s–1 = 15.65 ms–1 .

2
mv min
mg = or v2min = gr or vmin = gr =
r
So, the minimum speed, at the top, required to perform a vertical loop is 15.65 m s–1 .
Example 29. Prove that a motor car moving over a convex bridge is lighter than the same car resting on the same
bridge.
R
Solution : The motion of the motor car over a convex bridge AB is the motion
along the segment of a circle AB (Figure) ;
mg
The centripetal force is provided by the difference of weight mg of A B
the car and the normal reaction R of the bridge.


mv 2 mv 2
mg – R = or R = mg –
r r
Clearly R < mg, i.e., the weight of the moving car is less
than the weight of the stationary car.

Example 30. Prove that a motor car moving over a concave bridge is heavier than the same car resting on the
same bridge.
Solution : The motion of the motor car over a concave bridge AB is the mo-
R B
tion along the segment of a circle AB (Figure) ; A
The centripetal force is provided by the difference of normal reaction R of
the bridge and weight mg of the car.
mg


2 2
mv mv
R – mg = or R = mg +
r r
Clearly R > mg, i.e., the weight of the moving car is greater than the weight of the stationary car.

Example 31. A car is moving with uniform speed over a circular bridge of radius R which subtends an angle. of 90°
at its centre. Find the minimum possible speed so that the car can cross the bridge without losing

Let the car losses the contact at angle  with the vertical
the contact any where.
Solution :

mv 2
mgcos – N =
R

mv 2
N = mgcos – .......... (1)
R
for losing the contact N = 0 ,
 v= Rg cos  (from (1) )
for minimum speed, cos should be minimum so that  should be maximum.

max = 45°  cos 45° =

1
2

 Rg 
vmin =  
1/ 2

 2
Ans.

So that if car cannot lose the contact at initial or final point, car cannot be lose the contact any-
where.

"manishkumarphysics.in" 18
 PHYSICS
Example 32. A block of mass m is released from the top of a frictionless fixed A
hemisphere as shown. Find (i) the angle with the vertical where it
breaks off. (ii) the velocity at the instant when it breaks off. (iii) the
height where it breaks off. R

A N
Solution : At B ; N = 0 O
>
B

 mgcos  = R 
mv B2
h
R mg vB

 vB = gR cos  ........... (1)

O

Now by equation of energy between A and B we have ;

1 2
0 + mgR = mv B +mgh
2
put vB from (1)
and h = R cos 

 vB =
2 2R
gR and h = from the bottom
3 3
Example 33. Consider a simple pendulum having a bob of mass m suspended by string of length L fixed at its

string makes an angle  with the vertical. Find (i) tension in the string and (ii) magnitude of net force
upper end. The bob is oscillating in a vertical circle. It is found that the speed of the bob is v when the

on the bob at the instant.

Solution : (i) The forces acting on the bob are :
/////////////
(a) the tension T
(b) the weight mg 

As the bob moves in a circle of radius L with centre at O.

T
mv 2

A centripetal force of magnitude is required towards
mg sin  mg cos 
L
mg

cos . Thus,
O. This force will be provided by the resultant of T and mg

 2 
 g cos   v 
T – mg cos  = T = m L 
mv 2

or
L

g sin 
 v2 
 
2

 ar2   
2

 
(ii) anet = a 2t =

| Fnet | = manet = m g sin   2

 2 2 v4
Ans.
L

Example 34. A particle is projected with velocity 3gL at point A (lowest point
of the circle) in the vertical plane. Find the maximum height above
horizontal level of point A if the string slacks at the point B as
shown.

Solution : As tension at B ; T = 0

 mgcos  =
2
mv B
L

 vB = gL cos  ......... (1)

"manishkumarphysics.in" 19
 PHYSICS
Now by equation of energy between A and B.

mv B + mgL (1+cos )
1 1 2
0+ m 3gL =
2 2
put vB

 cos  =
1
3
 height attend by particle after the point B where the string slacks is ;

v B2 sin2  gL cos (1  cos 2 ) 4L

h’ = = =
2g 2g 27
 Maximum height about point A is given by ;

Hmax = L + Lcos  + h’ = L +
L 4L 40 L
+ =
3 27 27

9. CIRCULAR TURNING ON ROADS :

When vehicles go through turnings, they travel along a nearly circular arc. There must be some force which
will produce the required centripetal acceleration. If the vehicles travel in a horizontal circular path, this
resultant force is also horizontal. The necessary centripetal force is being provided to the vehicles by follow-
ing three ways.
1. By friction only
2. By banking of roads only.
3. By friction and banking of roads both.
In real life the necessary centripetal force is provided by friction and banking of roads both. Now let
us write equations of motion in each of the three cases separately and see what are the constant in
each case.

9.1 By Friction Only

Suppose a car of mass m is moving at a speed v in a horizontal circular arc of radius r. In this case, the
necessary centripetal force to the car will be provided by force of friction f acting towards center

f
mv 2
Thus,
Further, limiting value of f is N
r

or fL   N  mg (N = mg)

 fL
mv 2
Therefore, for a safe turn without sliding
r

 mg  or v  rg
mv 2 v2
or or
rg
Here, two situations may arise. If  and r are known to us, the speed of the vehicle should not exceed
r

rg and if v and r are known to us, the coefficient of friction should be greater than
v2
.
rg

Example 35. A bend in a level road has a radius of 100 m. Calculate the maximum speed which a car turning this
bend may have without skidding. Given :  = 0.8.

Solution : Vmax = rg = 0.8  100  10 = 800 = 28 m/s

"manishkumarphysics.in" 20
 PHYSICS
9.2. By Banking of Roads Only
Friction is not always reliable at circular turns if high speeds and sharp turns are involved to avoid depen-
dence on friction, the roads are banked at the turn so that the outer part of the road is some what lifted
compared to the inner part.
Applying Newton’s second law along the radius and the first law in the vertical direction.

N sin  
mv 2
r
or N cos = mg
from these two equations, we get

tan   v  rg tan 
v2
or
rg

Example 36. What should be the angle of banking of a circular track of radius 600 m which is designed for cars at
an average speed of 180 km/hr ?
Solution : Let the angle of banking be  . The forces on the car are (figure)
(a) weight of the car Mg downward and
(b) normal force N.
For proper banking , static frictional force is not needed.
For vertical direction the acceleration is zero. So,
Ncos  = Mg .....(i)
2
For horizontal direction , the acceleration is v / r towards the centre , so that
Nsin  = Mv2 / r .....(ii)
From (i) and (ii), tan  = v / rg
2

Putting the values , tan  = = 0.4167   = 22.6º.

180 ( km / h)2
(600 m) (10 m / s 2 )

9.3 By Friction and Banking of Road Both

If a vehicle is moving on a circular road which is rough and banked also, then three forces may act on the
vehicle, of these the first force, i.e., weight (mg) is fixed both in magnitude and direction.

 
N f N


 
mg f mg

Figure (i) Figure (ii)

The direction of second force, i.e., normal reaction N is also fixed (perpendicular to road) while the direction
of the third force i.e., friction f can be either inwards or outwards while its magnitude can be varied upto a
maximum limit (fL = N). So the magnitude of normal reaction N and directions plus magnitude of friction f are
mv 2
so adjusted that the resultant of the three forces mentioned above is towards the center. Of these m
r
and r are also constant. Therefore, magnitude of N and directions plus magnitude of friction mainly depends
on the speed of the vehicle v. Thus, situation varies from problem to problem. Even though we can see that :
(i) Friction f will be outwards if the vehicle is at rest v = 0. Because in that case the component of
weight mg sin is balanced by f.

"manishkumarphysics.in" 21
 PHYSICS
(ii) Friction f will be inwards if
v  rg tan 

(iii) Friction f will be outwards if

v  rg tan  and
(iv) Friction f will be zero if
v  rg tan 

(v) For maximum safe speed (figure (ii)

mv 2
N sin + f cos = ........(i)
r
N cos – f sin = mg .......(ii)
As maximum value of friction
f = N

sin    cos  rg(tan   )

 
v2
cos    sin  (1   tan )
= vmax =
rg

rg(tan    )
(1   tan )
Similarly ; vmin =

The expression tan  =

v2
Note :  also gives the angle of banking for an aircraft, i.e., the angle through
rg
which it should tilt while negotiating a curve, to avoid deviation from the circular path.

The expression tan  =

v2
 also gives the angle at which a cyclist should lean inward, when
rg
rounding a corner. In this case,  is the angle which the cyclist must make with the vertical which will
be discussed in chapter rotation.

10. CENTRIFUGAL FORCE :

When a body is rotating in a circular path and the centripetal force vanishes, the body would leave the
circular path. To an observer A who is not sharing the motion along the circular path, the body appears to fly
off tangentially at the point of release. To another observer B, who is sharing the motion along the circular
path (i.e., the observer B is also rotating with the body which is released, it appears to B, as if it has been
thrown off along the radius away from the centre by some force. This inertial force is called centrifugal force.)

mv 2
Its magnitude is equal to that of the centripetal force. = = m2r
r
Direction of centrifugal force, it is always directed radially outward.

Centrifugal force is a fictitious force which has to be applied as a concept

only in a rotating frame of reference to apply Newton’s law of motion in
that frame. FBD of ball w.r.t. non inertial frame rotating with the ball.
Suppose we are working from a frame of reference that is rotating at a constant, angular velocity  with
respect to an inertial frame. If we analyses the dynamics of a particle of mass m kept at a distance r from the
axis of rotation, we have to assume that a force mr2 react radially outward on the particle. Only then we can
apply Newton’s laws of motion in the rotating frame. This radially outward pseudo force is called the centrifu-
gal force.

"manishkumarphysics.in" 22
 PHYSICS
Example 37. A ring which can slide along the rod are kept at
mid point of a smooth rod of length L. The rod is
rotated with constant angular velocity  about
vertical axis passing through its one end. Ring is
released from mid point. Find the velocity of the
ring when it just leave the rod.

Solution : Centrifugal force

m2x = ma

2x =
vdv
dx

 2 x dx =  v dv
L v

(integrate both side.)

L/2 0

 x2 
2
 v2 
   
L v

 2   2 
 L / 2  0
=

 L2 L2 
2    = v
 2 8 
2

 2

L.
3
v=
2
Velocity at time of leaving the rod

 3 
(L )   L 
2

 2  L
2 7
 
v´ = = Ans.
2

11. EFFECT OF EARTHS ROTATION ON APPARENT WEIGHT :

The earth rotates about its axis at an angular speed of one revolution per 24 hours.
The line joining the north and the south poles is the axis of rotation.
Every point on the earth moves in a circle. A point at equator moves in a circle of
radius equal to the radius of the earth and the centre of the circle is same as the
centre of the earth. For any other point on the earth, the circle of rotation is smaller
than this. Consider a place P on the earth (figure).

Draw a perpendicular PC from P to the axis SN. The place P rotates in a circle with the centre at C. The
radius of this circle is CP. The angle between the line OM and the radius OP through P is called the latitude
of the place P. We have
CP = OP cos or, r = R cos
where R is the radius of the earth and  is colatitude angle.
If we work from the frame of reference of the earth, we shall have to assume
the existence of pseudo force. In particular, a centrifugal force mw2r has to
be assumed on any particle of mass m placed at P.
If we consider a block of mass m at point P then this block is at rest with
respect to earth. If resolve the forces along and perpendicular the centre of
earth then

"manishkumarphysics.in" 23
 PHYSICS
N + mr2 cos  = mg
 N = mg – mr2 cos 
 N = mg – mR2 cos2 

At equator ( = 0) W app. is minimum and at pole ( = /2) W app. is maximum.

This apparent weight is not along normal but at some angle  w.r.t. it. At all point except poles and equator
Note:

( = 0 at poles and equator)

Example 38. A body weighs 98N on a spring balance at the north pole. What will be the reading on the same
scale if it is shifted to the equator? Use g = GM/R2 = 9.8 m/s2 and Rearth = 6400 km.
Solution : At poles , the apparent weight is same as the true weight.
Thus, 98N = mg = m(9.8 m/s2)
At the equator , the apparent weight is
mg’ = mg – m2 R
The radius of the earth is 6400 km and the angular speed is
2 rad
 =
24  60  60s
= 7.27 × 10–6 rad/s
mg’ = 98N – (10 kg) (7.27 × 10–5 s–1)2 (6400 km)
= 97.66N Ans.

Problem 1. A fan rotating with  = 100 rad/s, is switched off. After 2n rotation its angular velocity becomes
50 rad/s. Find the angular velocity of the fan after n rotations.

"manishkumarphysics.in" 24
 PHYSICS
Solution : 2 = 02 + 2 
502 = (100)2 + 2 (2 . 2n)
If angular velocity after n rotation is n
...(1)

n2 = (100)2 + 2 (2n) ....(2)

from equation (1) and (2)

50 2  100 2 2( 2.2n)

 50 2  100 2
n2  100 2 =
22n
=2 2n 
2
 = 25 10 rad/s Ans.

Problem 2. Find angular velocity of A with respect to B at the instant shown in the figure.

Solution : Angular velocity of A with respect to B is ;

( v AB ) 
AB = rAB

vAB = 2 v = (vAB)  rAB = 2d

( v AB ) 
AB =
v 2 v
rAB = =
d 2 d

Problem 3. A particle is moving with a constant angular acceleration of 4 rad./sec2 in a circular path. At time
t = 0 particle was at rest. Find the time at which the magnitudes of centripetal acceleration and
tangential acceleration are equal.
Solution : at = R  v = 0 + Rt

v2  2R 2 t 2
ac = =
R R

 2R 2 t 2
 |at| = |ac|  R =  t2 = 
1 1 1

= t= sec. Ans.
R 4 2

Problem 4. The coefficient of friction between block and table is µ. Find the tension in the string
if the block moves on the horizontal table with speed v in circle of radius R.

mv 2
Solution : The magnitude of centripetal force is .
R

mv 2
(i) If limiting friction is greater than or equal to , then static friction alone provides centripetal
R
force, so tension is equal to zero.
T = 0 Ans.

mv 2
(ii) If limiting friction is less than , then friction as well as tension both combine to provide the
R
necessary centripetal force.

mv 2
T+fr=
R
"manishkumarphysics.in" 25
 PHYSICS
In this case friction is equal to limiting friction, fr = mg

 Tension = T = – mg
mv 2
Ans.
R

Problem 5. A block of mass m is kept on rough horizontal turn table at a distance r from centre of table.

angular acceleration .
Coefficient of friction between turn table and block is µ . Now turn table starts rotating with uniform

(i) Find the time after which slipping occurs between block and turn table.

at = r
(ii) Find angle made by friction force with velocity at the point of slipping.
Solution : (i)
speed after t time

= r  v = 0 + rt
dv
dt
Centripetal acceleration

= 2rt2
v2
ac =
r

Net acceleration anet = a 2t  a c2 =  2r 2   4r 2 t 4

block just start slipping
µmg = manet = m  2r 2   4r 2 t 4

 µ 2 g 2   2r 2   µg  2  1  2 
t =  
1/ 4

t =  2     
1/ 4

 
  4r 2    r     
Ans.

 2rt 2
tan = a  tan  =
ac
r
(ii)
t

  = tan–1 (t2) Ans.

Problem 6. A block is released from the top of a smooth vertical track,
which ends in a circle of radius r as shown.

(i) Find the minimum value of h so that the block completes the circle.
(ii) If h = 3r, find normal reaction when the block is at the points A and B.
(iii) If h = 2r , find the velocity of the block when it loses the contact with the track.
Solution : (i) For completing the circle, velocity at lowest point of circle (say A) is

 5gr 
5gr

 h=
1 2 5r
from energy conservation mgh = m Ans.
2 2
(ii) h = 3r
From energy conservation velocity at point A and B are

mvA2  vA =
1
mg.3r = 6gr
2

mvB2  vB = 2gr
1
mg.3r = mg2r +
2
Therefore normal reaction at A and B is -

 NA = 7mg
2
mv A
NA – mg =
r

 NB = mg
2
mv B
NB + mg =
r

"manishkumarphysics.in" 26
 PHYSICS
(iii) h = 2r
It loses contact with the track when normal reaction is zero

 mg cos  .......... (1)

mv 2
r
from energy conservation
1
mgh = mgr (1 + cos ) + mv2 ........ (2)
2
from (1) and (2)

2g(h  r ) 2gr
v= = Ans.
3 3

Problem 7. A point mass m connected to one end of inextensible string of length  and
other end of string is fixed at peg. String is free to rotate in vertical plane.
Find the minimum velocity give to the mass in horizontal direction so that
it hits the peg in its subsequent motion.

Solution : Tension in string is zero at point P in its subsequent motion, after this point its motion is projectile.

Velocity at point P, T = 0  mgcos =  v = g cos 

mv 2

Assume its projectile motion start at point P and it passes through point C. So that equation of
trajectory satisfy the co-ordinate of C (sin , – cos)
Equation of trajectory

gx 2
2v 2 cos 2 
y = xtan –

g( sin )2

2(g cos ) cos 2 
–  cos = sin tan –

sin2  1 sin 
 – cos =
2

cos  2 cos 3 
–

 – 2 cos4 = 2sin2 cos2 – sin2  sin2 = 2sin2 cos2 + 2cos4

 sin2 = 2cos2 (sin2 + cos2)  tan2 = 2

 tan  =   cos = , sin  =

1 2
2
3 3
From energy conservation between point P and A.
1 1
mu2 = mv2 + mg (1+cos)
2 2
 u2 = v2 + 2g (1 + cos )
 u2 = 2g + 3gcos

 u2 = 2g + 3g 
u = 2  3 g  
1 1/ 2
Ans.
3

Problem 8. A simple pendulum of length  and mass m free to oscillate in vertical plane. A nail is located at a
distance ‘d =  – a’ vertically below the point of suspension of a simple pendulum. The pendulum
bob is released from the position where the string makes an angle of 90° from vertical. Discuss the
motion of the bob if (a)  = 2a, (b)  = 2.5 a .
Solution : (a)  = 2a, Velocity at lowest point from energy conservation
1
0 + mg2a = mv2
2

"manishkumarphysics.in" 27
 PHYSICS

v= 4ga
Here radius of circle is ‘a’ about nail and velocity at lowest point is not sufficient to complete
the loop. Therefore motion of bob is combination of circular and projectile motion. Because
velocity at lowest point is lie between 3ga and 5ga .
(b)  = 2.5 a, Velocity at lowest point from energy conservation

mv2  v = 5ga
1
0 + mg(2.5a) =
2
here radius of circle is ‘a’ about nail and velocity at lowest point is just sufficient to complete
the loop so that here looping the loop about nail.

"manishkumarphysics.in" 28