Dpc130+Dpc200 Eng

DPC
Series
Pre-compensated Load Sensing Sectional Valves
DPC Series
Additional information
This catalogue shows the product in the most standard configurations.
Please contact Sales Dpt. for more detailed information or special request.
WARNING!
All specifications of this catalogue refer to the standard product at this date.
Walvoil, oriented to a continuous improvement, reserves the right to
discontinue, modify or revise the specifications, without notice.
WALVOIL IS NOT RESPONSIBLE FOR ANY DAMAGE CAUSED BY AN

1st edition July 2012
INCORRECT USE OF THE PRODUCT.
2 D1WWED02E
DPC Series General informations
____________________________________________________________________________________________
The DPC Series
The DPC Series is a family of open/closed center pre-pressure compensated sectional valves designed specifically for Mobile
Applications. The DPC series provides exceptional controllability, efficiency and flexibility for applications requiring up to
240 l/min (63.4 US gpm) flow rate. DPC Series is available in two different sizes: DPC130 and DPC200.
DPC130 DPC200
_________________________________________________________________________
The Load Sensing technology
Thanks to the use of specially designed pumps and control valves, the Load Sensing principle can be considered the most com-
prehensive means of creating a flexible hydraulic circuit that can adapt to the various operating conditions demanded by users.
The main feature of this principle is that the flow rate to the user is proportional to the spool position under any operating condi-
tion, regardless of the resistance encountered by the user (pressure) and the number of levers activated (exceeding the pump’s
total flow rate, a condition here in after defined as saturation, is the only limitation).
Therefore, with the LS systems, there is a specific correspondence between the position of the control lever and the movement
speed of the user, cylinder or hydraulic motor. This feature is particularly useful in the hydraulic handling machine sector (ex-
cavators, cranes, loaders, agricultural and forestry machinery) in which each movement phase has specific sequences that the
operator must control using memorised movements.
Advantages and options

• Energy saving.
• Extension of parts service life.
• Lower energy dissipation.
• Noise reduction.
• Available to create a single-pump circuit (compared with the use of multiple-pump circuits in which each pump is dedicated
to different actuators to be operated simultaneously).
Real energy savings can be obtained above all when the DPC directional valves operate together with variable displacement Load
Sensing pumps. When the DPC valve is utilised with fixed displacement pumps, the previously mentioned movement indepen-
dence and repeatability features are guaranteed, but energy savings will be limited.
For special options contact Sales Dept.
D1WWED02E 3
General informations DPC Series
Working conditions _____________________________________________________________________________________
This catalogue shows technical specifications and diagrams measured with mineral oil of 46 mm2/s - 46 cSt viscosity at 40°C -
104°F temperature.
DPC130 DPC200
on inlet port with compensator 150 l/min - 39.6 US gpm 260 l/min - 68.7 US gpm
@ stand-by (margin pressure) @ 9 bar - 131 ps @ 11.5 bar - 167 ps
Nominal flow rating on working ports with compensator 100 l/min - 26.4 US gpm 200 l/min - 52.8 US gpm
(open center circuit) @ stand-by (margin pressure) @ 7 bar - 102 ps @ 7 bar - 102 ps
on working ports without compensator 130 l/min - 34.3US gpm 240 l/min - 63.4 US gpm
@ stand-by (margin pressure) @ 9 bar - 131 ps @ 11.5 bar - 167 ps
inlet port P 315 bar (2) - 4500 psi (2) 350 bar (1) - 5100 psi (1)
Max. pressure
working ports A and B 315 bar ( ) - 4500 psi ( )
2 2
420 bar (1) - 6100 psi (1)
on outlet port T 25 bar - 363 psi 25 bar - 363 psi
Back pressure (max.)
on drain port L 2.5 bar - 36 psi 2.5 bar - 36 psi
Standard internal leakage ∆p=100 bar - 1450 psi 16 cm /min - 0.98 in /min
3 3
20 cm3/min - 1.22 in3/min
A(B)->T with port valves, ∆p=100 bar - 1450 psi 21 cm3/min - 1.28 in3/min 25 cm3/min - 1.53 in3/min
Fluid Mineral oil
with seals NBR (BUNA-N) from -20°C to 80°C - from -4°F to 176°F
Fluid temperature range
with seals FPM (VITON) from -20°C to 100°C - from -4°F to 212°F
operating range from 15 to 75 mm2/s - from 15 to 75 cSt
Viscosity min. 12 mm2/s - 12 cSt
max. 400 mm2/s - 400 cSt
Contamination level max. -/18/15 - ISO 4406 - NAS 1638 class 9
with mechanical devices from -40°C to 60°C - from -40°F to 140°F
Environmental temperature
with hydraulic/pneumatic devices from -30°C to 60°C - from -22°F to 140°F
for working conditions
with electric/electrohydraulic devices from -20°C to 50°C - from -4°F to 122°F
NOTES: (1) According to NFPA T 2.6.1., fatigue rating verified for 1 million cycles on 6 sample valves with test Pressure = 1.23 x Max.
pressure indicated - (2) Intermittent pressure at max. 250,000 cycles with specific internal testing.
4 D1WWED02E
DPC Series General informations
_________________________________________________________________________________________
Standard threads
REFERENCE STANDARD
BSP UN-UNF NPTF Flange connection
THREAD ISO 228/1 ISO 263 ISO 6162
ANSI B1.20.3
ACCORDING TO BS 2779 ANSI B1.1 unified SAE J518
CAVITY ISO 1179 11926

DIMENSION SAE J1926 J476a SAE J518 code 61 (3)
ACCORDING TO DIN 3852-2 shape X or Y ISO 6162-1 (4)
NOTEs (3): Standard pressure series - (4): For pressure up to 350 bar (5100 psi)
DPC130 DPC200
PORTS Flange connection (bolts threading)
THREADING BSP UN-UNF BSP UN-UNF ISO 6162-1 SAE J518
type 1 code 61
Inlet P G 3/4 1 1/16-12 (SAE 12) G1 1 5/16-12 (SAE 16) DN 19 (M10) 3/4 (3/8-16 UNC)
Ports A and B G 1/2 7/8-14 (SAE10) G1 1 5/16-12 (SAE 16) DN 19 (M10) 3/4 (3/8-16 UNC)
Outlet T G 3/4 1 1/16-12 (SAE 12) G 1-1/4 1 5/8-12 (SAE 20) DN 25 (M10) 1 (3/8-16 UNC)
Load Sensing LS G 1/4 9/16-18 (SAE 6) G 1/4 9/16-18 (SAE 6)
Pilot V1 G 1/4 9/16-18 (SAE 6) G 1/4 9/16-18 (SAE 6)
depends on inlet section type:
Pilot V2 M14x1.5 (5)
see pages from 14 to 17 (5) see BSP threading see UN-UNF threading
Drain L G 1/4 7/16-20 (SAE 4) G 1/4 7/16-20 (SAE 4)
Pressure gauge M G 1/4 9/16-18 (SAE 6) G 1/4 9/16-18 (SAE 6)
Hydraulic control ports G 1/4 9/16-18 (SAE 6) G 1/4 9/16-18 (SAE 6)
NOTE (5): ATTENTION! pilot port V2 requires dedicate joints, please see Inlet section pages.
D1WWED02E 5
Index DPC Series
Contents
DPC130
Dimensional data and performance . . . . . . . . . . . . . . . . . page 8
Hydraulic circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..... 9
Complete sections ordering codes . . . . . . . . . . . . . . . . . . . . . 10
• Inlet section
Inlet section parts ordering codes . . . . . . . . . . . . . . page 12
Dimensions and hydraulic circuit . . . . . . . . . . . . . . . .... 14
L.S. pressure relief valves . . . . . . . . . . . . . . . . . . . .... 19
Solenoid operated unloading valve . . . . . . . . . . . . . .... 19
• Working section
Working section parts ordering codes . . . . . . . . . . . page 20
Spools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... 25
"A" side spool control kit . . . . . . . . . . . . . . . . . . . . .... 27
Electrohydraulic controls without on board electronic .... 29
Electrohydraulic controls with on board electronic . . . .... 33
"B" side spool control kit . . . . . . . . . . . . . . . . . . . . .... 36
Port valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... 37
L.S. port relief valves . . . . . . . . . . . . . . . . . . . . . . .... 37
• Outlet section
Outlet section parts ordering codes . . . . . . . . . . . . . page 38
Dimensions and hydraulic circuit . . . . . . . . . . . . . . . . . . . 39
Drain options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
DPC200
Dimensional data and performance . . . . . . . . . . . . . . . . page 40
Hydraulic circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Complete sections ordering codes . . . . . . . . . . . . . . . . . . . . . 42
• Inlet section
Inlet section parts ordering codes . . . . . . . . . . . . . . page 44
Pressure reducing valve . . . . . . . . . . . . . . . . . . . . . .... 48
Solenoid operated unloading valve . . . . . . . . . . . . . .... 48
L.S. pressure relief valves . . . . . . . . . . . . . . . . . . . .... 49
• Working section
Working section parts ordering codes . . . . . . . . . . . page 50
Spools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... 54
"A" side spool control kit . . . . . . . . . . . . . . . . . . . . .... 56
Electrohydraulic controls . . . . . . . . . . . . . . . . . . . . .... 58
"B" side spool control kit . . . . . . . . . . . . . . . . . . . . .... 60
Port valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .... 61
L.S. port relief valves . . . . . . . . . . . . . . . . . . . . . . .... 62
• Outlet section
Outlet section parts ordering codes . . . . . . . . . . . . . page 63
Dimensions and hydraulic circuit . . . . . . . . . . . . . . . . . . . 64
Drain options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
6 D1WWED02E
DPC Series Index
Special configurations
Connection between DPC Series valves . . . . . . . . . . page 66
Accessories
Coils and connectors . . . . . . . . . . . . . . . . . . . . . . . page 68
Istallation and maintenace . . . . . . . . . . . . . . page 70
Appendices
Appendix A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 71
D1WWED02E 7
DPC130 DPC Series
Dimensional data and performance ________________________________________________________________
181.5 81 48 50 53
7.15 3.19 2.01 1.97 2.09
54.5 37.1 16 16 10
2.15 1.46 0.63 0.63 0.39
Ø 8.5
2.28
Ø 0.33
58
5
0.31
0.197
0.19
4.7
8
0.43
11
P
33.5
1.32
L A2 A1
43.5
2.01
4.57
116
10.51
3.94
100
267
1.30
33
45.5
1.79
LS B2 B1
33.5
1.32
0.35
9
0.31
8
130.4 8 E
5.13 0.31
152 F
5.98
P⇒T Pressure drop inlet compensator

(margin pressure)
0 8 16 24 32 (US gpm)
40
E F Weight (psi)
Type (bar) 500
mm in mm in Kg lb 30
400
Pressure
DPC130/1 184 7.24 200 7.87 12.4 27.3

20 300
DPC130/2 232 9.13 248 9.76 19.4 42.8
200
DPC130/3 280 11.02 296 11.65 25.3 55.8 10
DPC130/4 328 12.91 344 13.54 31.0 68.3 100
DPC130/5 376 14.80 392 15.43 36.5 80.5 0 0

0 30 60 90 120 150 (l/min)
DPC130/6 424 16.69 440 17.32 42.6 93.9 Flow
DPC130/7 472 18.58 488 19.21 48.7 107.0
A(B)⇒T pressure drop
DPC130/8 520 20.47 536 21.10 54.8 121.0 (standard spool @ max.stroke)
DPC130/9 568 22.36 584 22.99 60.9 134.0 24
0 8 16 32 (US gpm)
40
DPC130/10 616 24.25 632 24.88 67.0 148.0 without compensator
(psi)
(bar) with compensator 500
26.4 US gpm
34.3 US gpm
100 l/min
130 l/min
30
8th section 400
Pressure
20 300
1st section
200
10
100
0 0
0 30 60 90 120 150 (l/min)
Flow
8 D1WWED02E
DPC Series DPC130
__________________________________________________________________________________________
Hydraulic circuit
Open center configuration example
B2 A2 B1 A1
P T
V2
L
V1
LS
LSAB LSAB
Open center circuit and one-side proportional electrohydraulic control with lever,
with unloader valve and pressure reducing valve, port valves arrangement on all
ports, LSAB port, internal pilot and external drain
Closed center configuration example
B2 A2 B1 A1
P T
V2
L
V1
LS
LSAB LSAB
Closed center circuit and one-side proportional electrohydraulic control
with lever, with unloader valve and pressure reducing valve, antishock and
anticavitation valves on all ports, L.S. relief valves on 2th section, LSAB ports,
internal pilot and external drain
D1WWED02E 9
DPC130 DPC Series
Complete sections ordering codes __________________________________________________________________
DPC130 / 2 / BR21-S220-ELP / C10-1S8EZ3L1 / C10-1S8EZ3L1 /..... / RF30 - ...... - 12VDC - <SB20 - CVN>
Valve type 1 2 3 4 5 6
Nr. of working sections The valve is supplied painted,

as standard, with one coat of
Primer black antirust paint
1
7
2
1 Inlet section * page 12

TYPE: DPC130/BR-S200-DSK CODE: 634200000 Open Center circuit
DESCRIPTION: With 3-way compensator, L.S. pressure relief valve, TYPE: DPC130/BN11-S220 CODE: 634220004
pressure reducing valve and selector for open/closed center circuit DESCRIPTION: With 3-way compensator and L.S. pressure relief
Closed Center circuit valve, without pressure reducing valve
TYPE: DPC130/BN21-S220 CODE: 634220003 TYPE: DPC130/BR11-S220-ELP-12VDC CODE: 634210002
DESCRIPTION: With 3-way compensator and L.S. pressure relief DESCRIPTION: As previous, with pressure reducing valve, and 12VDC
valve, without pressure reducing valve solenoid operated unloader valve
TYPE: DPC130/BR21-S220-ELP-12VDC CODE: 634210001 TYPE: DPC130/BRS11-S220-ELP-12VDC CODE: 634230002
DESCRIPTION: As previous, with pressure reducing valve, and 12VDC DESCRIPTION: Copy-Spool with dumper configuration, with 3-way
solenoid operated unloader valve compensator, pressure reducing valve, L.S. pressure relief valve and
TYPE: DPC130/BRF21-S250 CODE: 634250900 12VDC solenoid operated unloader valve
DESCRIPTION: Without compensator, with pressure reducing valve
and L.S. pressure relief valve
TYPE: DPC130/BRSO21(SF)-S220-ELN3-12VDC CODE: 634240003
DESCRIPTION: Shut-off configuration, with pressure reducing valve
and L.S. pressure relief valve
TYPE: DPC130/BRS21-S220-ELP-12VDC CODE: 634230003
DESCRIPTION: Copy-Spool with dumper configuration, with 3-way
compensator, pressure reducing valve, L.S. pressure relief valve and
12VDC solenoid operated unloader valve
10 D1WWED02E
DPC Series DPC130
___________________________________________________________________
Complete sections ordering codes
2 Working section * page 20 3 Outlet section * page 38
With 2-way compensator For valve with mechanical control
TYPE: DPC130/C10-1S8EZ3L1-12VDC CODE: 634110029 TYPE: DPC130/RF10 CODE: 634310001
DESCRIPTION: With double acting spool for 60 l/min (16 US gpm), DESCRIPTION: Without ports
proportional electrohydraulic control with lever For valve with hydraulic control
TYPE: DPC130/C22-1S8EZ3L1.UTUTSTST-12VDC TYPE: DPC130/RF20 CODE: 634310000
CODE: 634110030 DESCRIPTION: Without ports, internal drain
DESCRIPTION: As previous, arranged for port valves and L.S. relief For valve with electrohydraulic control
valves TYPE: DPC130/RF30 CODE: 634310002
TYPE: DPC130/C10-1S8ZR4FL1-12VDC CODE: 634110031 DESCRIPTION: Without ports, external drain L
DESCRIPTION: With double acting spool for 60 l/min (16 US gpm), TYPE: DPC130/RC31 CODE: 634310012
proportional electrohydraulic control with simple diagnostic and DESCRIPTION: With ports P1 and T1 (plugged), external drain L
programmability, ratiometric output, with lever TYPE: DPC130/RD31 CODE: 634310015
TYPE: DPC130/C22-1S8ZR4FL1.UTUTSTST-12VDC DESCRIPTION: With ports P1 and T1 (plugged), port LS1, external
CODE: 634110032 drain L
DESCRIPTION: As previous, arranged for port valves and L.S. relief
valves 4 Valve threading
TYPE: DPC130/C10-1S8ZR4PL1-12VDC CODE: 634110033
Specify only if it is different from BSP standard (see page 5).
DESCRIPTION: With double acting spool for 60 l/min (16 US gpm),
proportional electrohydraulic control with simple diagnostic and
programmability, absolute output, with lever 5 Voltage
TYPE: DPC130/C22-1S8ZR4PL1.UTUTSTST-12VDC Specify the voltage of electric device
CODE: 634110034
6 Pump stand-by
valves
Without compensator This option must be specified only if valve is configured for Closed
TYPE: DPC130/D10-1S8EZ3L1-12VDC CODE: 634120010 Center circuit, without local compensation and if the value is different
DESCRIPTION: With double acting spool for 60 l/min (16 US gpm), from 11.5 bar (167 psi)
proportional electrohydraulic control with lever
TYPE: DPC130/D20-1S8EZ3L1.UTUT-12VDC 7 Assembling kit
CODE: 634120011
CODE CODE DESCRIPTION
DESCRIPTION: As previous, arranged for port valves
With inlet sections type
TYPE: DPC130/D10-1S8ZR4FL1-12VDC CODE: 634120012
BR-BN-BRS-BRSO BRF
5TIR108185 5TIR108153 For 1 working section valve
5TIR108232 5TIR108201 For 2 working sections valve
programmability, ratiometric output, with lever
TYPE: DPC130/D20-1S8ZR4FL1.UTUT-12VDC
CODE: 634120013
TYPE: DPC130/D10-1S8ZR4PL1-12VDC CODE: 634120014
programmability, absolute output, with lever
TYPE: DPC130/D20-1S8ZR4PL1.UTUT-12VDC
CODE: 634120015
TYPE: DPC130/CV10-1S8EZ3L1-12VDC CODE: 634130001
DESCRIPTION: With load check valve, double acting spool for
60 l/min (16 US gpm), proportional electrohydraulic control, with lever
TYPE: DPC130/CV22-1S8EZ3L1.UTUTSTST-12VDC
CODE: 634130002
NOTE (*): Codes are referred to BSP thread.
valves
D1WWED02E 11
DPC130 DPC Series
Inlet section parts ordering codes _________________________________________________________________
Valve setting (bar)
DPC130 / BN21 - S220 - ...... DPC130 / BR21 - S220 - ELP - ...... - 12VDC
1 2 5 1 2 3 5 6
2 2
1
1
3
5
DPC130 / BRS21 - S220 - ELP - ...... - 12VDC DPC130 / BRSO21(SF) - S220 - ELN3 - ...... - 12VDC
1 2 3 5 6 1 2 4 5 6
2 6
2
3
6
DPC130 / BRF21 - S250 - BSP
1 2 5
Circuit conversion kit
7
2
12 D1WWED02E
DPC Series DPC130
___________________________________________________________________
Inlet section parts ordering codes
1 Inlet section kit* page 14 4 Shut-Off pilot solenoid valve page 16

Open Center circuit Needs coil type BT: see chapter 6
TYPE: DPC130/BN11 CODE: 5FIA630303 TYPE CODE DESCRIPTION
DESCRIPTION: With compensator, without pressure reducing valve ELN3 0EJ08002035 Without emergency override
TYPE: DPC130/BR11 CODE: 5FIA630301 ELT3 0EJ08002042 With screw emergency override
DESCRIPTION: With compensator and pressure reducing valve
TYPE: DPC130/BRS11 CODE: 5FIA630361 5 Section threading
DESCRIPTION: Copy-Spool type, with compensator and pressure
reducing valve
Closed Center circuit
TYPE: DPC130/BN21 CODE: 5FIA630302 6 Coil
DESCRIPTION: Without compensator and pressure reducing valve TYPE CODE DESCRIPTION
TYPE: DPC130/BR21 CODE: 5FIA630300 12VDC 4SLE001200 12VDC coil type BER, ISO4400 connector
DESCRIPTION: Without compensator, with pressure reducing valve (for unloading valve)
TYPE: DPC130/BRSO21(SF) CODE: 5FIA630371 12VDC 4SL3000120 12VDC coil type BT, ISO4400 connector
DESCRIPTION: Shut-Off type, without compensator, with pressure (for Shut-Off pilot valve)
reducing valve For complete available coils list see page 68.
TYPE: DPC130/BRS21 CODE: 5FIA630360
DESCRIPTION: Copy-Spool type, without compensator, with pressure
7 Pressure reducing valve page 18
reducing valve
TYPE: DPC130/BRF21 CODE: 5FIA630306 CODE DESCRIPTION
DESCRIPTION: Without compensator, with pressure reducing valve X219740033 Pressure reducing valve for BRF inlet section
2 L.S. relief valves page 19 8 Circuit conversion kit

Standard setting is referred to 10 l/min - 2.6 US gpm flow. These kits ara available only for BN and BR sections; not for BRS,
TYPE CODE DESCRIPTION BRSO and BRF sections.
LSD XCAR126215 With blind nut, range 40-180 bar / CODE DESCRIPTION
580-2600 psi, std. setting 90 bar / 1300 psi 5KIT130300 Kit for circuit conversion from Open Center to Closed
XCAR126213 As previous, range 180-350 bar / Center
2600-5100 psi std. setting 180 bar / 2600 psi 5KIT130310 Kit for circuit conversion from Closed Center to Open
LSH XCAR126216 With locked arrangement, range 40-180 bar Center
/ 580-2600 psi, std. setting 90 bar / 1300 psi
XCAR126217 As previous, range 180-350 bar /
2600-5100 psi, std. setting 180 bar / 2600 psi
LSZ 5CAR126221 With anti-tamper cap, range 40-180 bar
5CAR126219 As previous, range 180-350 bar /
ST 5KIT126210 Relief valve blanking plug
3 Solenoid operated unloading valve page 19

Needs coil type BER: see chapter 6
TYPE CODE DESCRIPTION
ELN 0EC08002031 Without emergency override
ELP 0EC08002033 With push-button emergency override
ELT 0EC08002035 With “twist & push” emergency override
ELV 0EC08002034 With screw type emergency override NOTE (*): Codes are referred to BSP thread.
LT XTAP225320 Unloading valve blanking plug
D1WWED02E 13
DPC130 DPC Series
Inlet section _______________________________________________________________________________________________
Dimensions and hydraulic circuit
Example of BN section
21.5
0.85
V1
31.5
1.24
V2
max.164.4
max. 6.47
LS
130.4
5.13
LS
3.31
84
54.5
2.15
0.39
10
28 2 7 115.5
1.10 0.079 0.276 4.55
129.5
5.10
0.39
10
Auxiliary ports specification
V1 = G1/4 pilot pressure port for electrohydraulic
2.76
controls feeding (Pmax = 315 bar / 4600 psi) (P⇒IN)

70
T
V2 = G1/4 pressure gauge connection P
2.09
53
LS
0.67
17
36.5 43.5 11
1.44 1.71 0.43
100 8
3.94 0.31
BN11 type BN21 type
P T P T
V2 V2
V1 V1
LS
LS
14 D1WWED02E
DPC Series DPC130
________________________________________________________________________________________________
Inlet section
Example of BR section
21.5
0.85
V1
31.5
1.24
V2
max.164.4
max. 6.47
LS LS
130.4
5.13
3.31
84
54.5
2.15
0.39
10
33.5
1.32
28 7 115.5
1.10 0.276 4.55
129.5
5.10
max. 213.5
max. 8.41
0.39
10
V1 = G1/4 pilot pressure port (Pmax = 30 bar / 435 psi) for
hydraulic pilot control valves feeding (P⇒OUT) T
2.76
70
V2 = M14x1.5 pilot pressure port for:

P
1.42
- electrohydraulic controls optional feeding (Pmax = 315 bar /

36
2.09
53
4600 psi) (P⇒IN); needs G1/4 joint, code 5GIU519611
- pressure gauge connection; needs G1/4 joint, code 5GIU620330.
LS
0.67
36.5 43.5 11
17
1.44 1.71 0.43

100 8
3.94 0.31
BR11 type BR21 type Pressure reducing valve diagram

Reduced pressure vs. Flow
P T P T 0 0.8 1.6 2.4 3.6 (US gpm)
40 (psi)
(bar)
500
Reduced pressure
V2 V2 30
400
20 300
200
V1 V1 10
100
0 0
0 3 6 9 12 15 (l/min)
Flow
LS
LS
D1WWED02E 15
DPC130 DPC Series
Inlet section _______________________________________________________________________________________________
Example of BRSO21 section

For pressure reducing valve features, see page 15
Shut-off pilot
solenoid valve
20.5
0.81
max. 219
max. 8.62
T P
M
130.4
LS
5.13
110.8
4.36
0.39
1.89
10
V1
48
27.6 115.5
1.08 4.55
17 127
0.67 5.00
9
0.354
0.55
T
14
M = G1/4 pressure gauge connection P

V1 = G1/4 pilot pressure port for electro-
hydraulic controls optional feeding (Pmax =
315 bar / 4600 psi) (P⇒IN)
LS
2.48
63
1.93
V1
49
1.26
1.10
32
28
2.8
0.110
6.5 39.5 45 8
0.256 1.56 1.77 0.31
100
3.94
Pilot solenoid valve type ELN3 Pilot solenoid valve type ELT3
without emergency screw type emergency
1 1
A
2 3 2 3
wrench 24
30 Nm - 22 lbf
3 3
2 2
1 1
Features Valve Dim. A

Max. flow . . . . . . . . . . . . . . . . : 3 l/min - 0.80 US gpm type mm in
Max. pressure . . . . . . . . . . . . . : 350 bar - 5100 psi
Internal leakage . . . . . . . . . . . : 10 cm3/min @ 210 bar ELN3 65.5 2.58
0.61 in3/min @ 3050 psi ELT3 88.5 3.48
For coil features and options see coil BT at page 68.
16 D1WWED02E
DPC Series DPC130
________________________________________________________________________________________________
Inlet section
Example of BRS section

For pressure reducing valve features, see page 15
12
0.47
V1 LS
31.5
1.24
V2
max.164.4
max. 6.47
130.4
5.13
107.2
4.22
3.31
84
0.39
10
31.5
1.24
28 21.5 115.5 38 17
1.10 0.85 4.55 1.50 0.67
53 144 70
2.09 5.67 2.76
max. 213.5
max. 8.41
16.5 43.5 11
Auxiliary ports specification 0.65 1.71 0.43
V1 = G1/4 pilot pressure port (Pmax =
0.39
10
30 bar / 435 psi) for hydraulic pilot control
valves feeding (P⇒OUT)
V2 = M14x1.5 pilot pressure port for: T
P
- electrohydraulic controls optional fee-
ding (Pmax = 315 bar / 4600 psi) (P⇒IN);
2.09
53
needs G1/4 joint, code 5GIU519611

LS
- pressure gauge connection; needs G1/4
joint, code 5GIU620330.
7.5 100 8
0.295 3.94 0.315
BRSO11 type BRSO21 type
P T P T
V2 V2
V1 V1
LS
LS
D1WWED02E 17
DPC130 DPC Series
Inlet section _______________________________________________________________________________________________
Example of BRS section
Pressure reducing valve
P T
M
T 5.83
148
132.5
5.22
1.42
36
LS P
LS
M
1.81
46
1.50
34.5
1.36
38
46.8 24.2 14 17
0.39
1.84 0.95
10
0.55 0.67
100 38 LS
3.94 1.50
6 30.5
0.236 1.20
LS
M M = G1/4 pressure gauge connection
1.42
36
1.06
27
64 7.5
2.52 0.295
115.5
4.55
137
5.39
Pressure reducing valve Pressure reducing valve diagram

Reduced pressure vs. Flow
wrench 10 0 0.8 1.6 2.4 3.6 (US gpm)
60
2
1 24 Nm - 17.7 lbf (bar) 800
(psi)
Reduced pressure
3
3 45
2 600
1
30
400
Features
Reduced press. range . : from 3.5 to 35 bar 15 200
: from 50 to 500 psi
Max. inlet pressure . . . : 380 bar - 5500 psi 0 0
Nominal flow . . . . . . . : 15 l/min - 4 US gpm 0 3 6 9 12 15 (l/min)
Flow
18 D1WWED02E
DPC Series DPC130
________________________________________________________________________________________________
Inlet section
L.S. pressure relief valve
Type LSH Type LSD

with lock arrangement with blind nut
Pressure vs. flow diagram
W Z (1) = valve range 40-180 bar (580-2600 psi)
Y Y (2) = valve range 180-350 bar (2600-5000 psi)
B
X X 0 10 20 30 (US gpm)
400 (psi)
J (bar) max. setting (2)
J 5000
300
medium range setting (2) 4000
Pressure
Type LSZ Type ST 3000
200 max. setting (1) min. and std. setting (2)
with anti-tamper cap valve blanking plug
2000
cap parts K std. setting (1)
100
4COP116240 min. setting (1) 1000
X J 0 0
0 30 60 90 120 150 (l/min)
Flow
J
X = wrench 13 / 42 Nm - 31 lbf Dim. B

Valve
Y = wrench 10 / 9.8 Nm - 7.2 lbf
type mm in
W = allen wrench 3
Z = wrench 10 / 9.8 Nm - 7.2 lbf LSD 21.5 0.85
J = wrench 7 / 24 Nm - 17.7 lbf LSH 17 0.67
K = allen wrench 5 / 24 Nm - 17.7 lbf
LSZ 34 1.34
Solenoid operated unloading valve
Type ELN: without emergency Type ELP: push button type On BR and BRS section
wrench 24
30 Nm - 22 lbf
1 1
2 2
1 1
Valve Dim. C
type mm in
2 2
ELN 65.5 2.58
Type ELV: screw type Type ELT: “push & twist” type ELP 88.5 3.48
ELV 88.5 3.48
ELT 91 3.58
1 1
C
2 2
1 1 Features
Max. flow . . . . . . . . . . . . . . . . : 40 l/min - 10.6 US gpm
2 2 Max. pressure . . . . . . . . . . . . . : 380 bar - 5500 psi
Internal leakage . . . . . . . . . . . : 0.25 cm3/min @ 210 bar
LT: valve blanking plug 0.015 in3/min @ 3050 psi
For coil features and options see coil BER at page 68.
allen wrench 10
24 Nm - 17.7 lbf
D1WWED02E 19
DPC130 DPC Series
Working and outlet section parts ordering codes _______________________________________________

Valve setting (bar)
port A port B port A port B
DPC130/C22-1S-8EZ3 L 1 . U100U320.S250S250-......-12VDC
6 8
1 2 3A 4 5 6 7 3
3B Lever position: see page 36 5
1 Working section kit* page 22

With compensator
TYPE: DPC130/C10 CODE: 5EL6301310
2
DESCRIPTION: Without valves arrangement 3
3
DESCRIPTION: As previous with additional upper L.S. port 4
DESCRIPTION: With port valves arrangement
1
DESCRIPTION: As previous with additional upper L.S. port
DESCRIPTION: Arranged for port valves and one L.S. relief valve 3
DESCRIPTION: As previous with additional upper L.S. port
DESCRIPTION: Arranged for port valves and two L.S. relief valves
2 Spool page 25
TYPE: DPC130/F10 CODE: 5EL6304310 Flow is referred to 7 bar (102 psi) stand-by (margin pressure)
DESCRIPTION: For floating circuit, without port valves arrangement TYPE CODE DESCRIPTION
TYPE: DPC130/F20 CODE: 5EL6304320 Double acting with A and B closed in neutral position
DESCRIPTION: For floating circuit, with port valves arrangement 1C 3CU4010005 5 l/min (1.3 US gpm) flow
TYPE: DPC130/CM23 CODE: 5EL6301325A 1D 3CU4010010 10 l/min (2.6 US gpm) flow
DESCRIPTION: For regenerative circuit, arranged for port valves and 1V 3CU4010025 25 l/min (6.6 US gpm) flow
one L.S. relief valve 1Q 3CU4010040 40 l/min (10.6 US gpm) flow
Without compensator 1S 3CU4010060 60 l/min (15.9 US gpm) flow
TYPE: DPC130/D10 CODE: 5EL6302310 1N 3CU4010080 80 l/min (21.1 US gpm) flow
DESCRIPTION: Without valves arrangement 1P 3CU4010100 100 l/min (26.4 US gpm) flow
TYPE: DPC130/D20 CODE: 5EL6302320 Double acting with A and B to tank in neutral position
DESCRIPTION: With port valves arrangement 2C 3CU4024005 5 l/min (1.3 US gpm) flow
TYPE: DPC130/D21 CODE: 5EL6302321 2D 3CU4024010 10 l/min (2.6 US gpm) flow
DESCRIPTION: Arranged for port valves and one L.S. relief valve 2V 3CU4024025 25 l/min (6.6 US gpm) flow
TYPE: DPC130/G20 CODE: 5EL6305320 2Q 3CU4024040 40 l/min (10.6 US gpm) flow
DESCRIPTION: For floating circuit, with port valves arrangement 2S 3CU4024060 60 l/min (15.9 US gpm) flow
TYPE: DPC130/DM23 CODE: 5EL6302350 2N 3CU4024080 80 l/min (21.1 US gpm) flow
DESCRIPTION: For regenerative circuit, arranged for port valves and 2P 3CU4024100 100 l/min (26.4 US gpm) flow
one L.S. relief valve Double acting with A and B partially to tank in neutral position
Without compensator, with check valve 2HC 3CU4025005 5 l/min (1.3 US gpm) flow
TYPE: DPC130/CV10 CODE: 5EL6301316 2HD 3CU4025010 10 l/min (2.6 US gpm) flow
DESCRIPTION: Without valves arrangement 2HV 3CU4025025 25 l/min (6.6 US gpm) flow
TYPE: DPC130/CV13 CODE: 5EL6301314 2HQ 3CU4025040 40 l/min (10.6 US gpm) flow
DESCRIPTION: As previous with additional upper L.S. port 2HS 3CU4025060 60 l/min (15.9 US gpm) flow
TYPE: DPC130/CV20 CODE: 5EL6301324 2HN 3CU4025080 80 l/min (21.1 US gpm) flow
DESCRIPTION: With port valves arrangement 2HP 3CU4025100 100 l/min (26.4 US gpm) flow
TYPE: DPC130/CV21 CODE: 5EL6301326 Single acting on A, B plugged: needs G1/2 plug
DESCRIPTION: Arranged for port valves and one L.S. relief valve 3V 3CU4031025 25 l/min (6.6 US gpm) flow
TYPE: DPC130/CV23 CODE: 5EL6301328 3Q 3CU4031040 40 l/min (10.6 US gpm) flow
DESCRIPTION: As previous with additional upper L.S. port 3S 3CU4031060 60 l/min (15.9 US gpm) flow
TYPE: DPC200/CV22 CODE: 5EL6301327 3N 3CU4031080 80 l/min (21.1 US gpm) flow
DESCRIPTION: Arranged for port valves and two L.S. relief valves 3P 3CU4031100 100 l/min (26.4 US gpm) flow
TYPE: DPC130/FV20 CODE: 5EL6304325 Double acting with A and B closed in neutral position, 4
DESCRIPTION: For floating circuit, with port valves arrangement positions, floating in 4th pos. with spool out: needs sections
TYPE: DPC130/CVM23 CODE: 5EL6301350 type F, G or FV, positioner and controls type 13
DESCRIPTION: For regenerative circuit, arranged for port valves and 5V 3CU4041025 25 l/min (6.6 US gpm) flow
one L.S. relief valve 5Q 3CU4041040 40 l/min (10.6 US gpm) flow
5S 3CU4041060 60 l/min (15.9 US gpm) flow
NOTE (*): Codes are referred to BSP thread. 5N 3CU4041080 80 l/min (21.1 US gpm) flow
20 D1WWED02E
DPC Series DPC130
_______________________________________________
Working and outlet section parts ordering codes
2 Spool (continued) page 25 3A "A" side spool control kit page 27
Double acting with A and B closed in neutral position, 3 TYPE CODE DESCRIPTION
positions, regenerative in 3rd pos. with spool out: needs Mechanical positioners
sections type CM, DM or CVM, dedicated controls type 8 with 7FT 5V07130000 With friction and center pos. feeling
reduced stroke 8 5V08130000 3 position, spring return to neutral position
8F 3CU4033070 50-70 l/min flow (port A-port B) 13 5V13130000 For floating circuit (spool type 5), 4 pos.,
(13.2-18.5 US gpm) detent in 4th position, with spring return to
Double acting with A and B closed in neutral position, 4 neutral position
positions, regenerative in 4th pos. with spool out: needs Proportional hydraulic controls
sections type CM, DM or CVM, dedicated controls type 13 8IM 5V08130780 Range 5-15 bar (73-218 psi)
8Y 3CU4044070 70 l/min (18.5 US gpm) flow
4 "B" side spool control kit page 36
3B Electrohydraulic controls TYPE CODE DESCRIPTION
TYPE CODE DESCRIPTION L 5LEV130712 Aluminium lever box
Proportional controls without on-board electronic ...... page 29 LN 5LEV130701 Aluminium lever box, without lever
Standard type LZ 5LEV130731 Aluminium lever box, with anti-tamper
8EZ3-12VDC 5V08130780 With ISO4400 connector screw caps
8EZ3-24VDC 5V08130781 With ISO4400 conNector LG 5LEV130806 Cast iron lever box
8EZ4-12VDC 5V08130880 With flying leads
8EZ4-24VDC 5V08130881 With flying leads 5 Port valves page 37
8EZ4D-12VDC 5V08130886 With Deutsch connector
8EZ4D-24VDC 5V08130887 With Deutsch connector
UT XTAP522442 Valve blanking plug
Standard type, for floating circuit (spool type 5)
C 5KIT410000 Anticavitation valve
13EZ3-12VDC 5V13130780 With ISO4400 connector
Fixed setting antishock and anticavitation valves: setting is
referred to 10 l/min (2.6 US gpm)
Standard type, for 3 positions regenerative circuit (spool type 8F)
TYPE: U 100 CODE: 5KIT330 100
8EZ3CR-12VDC 5V08130798 With ISO4400 connector
8EZ3CR-24VDC 5V08130799 With ISO4400 connector setting (bar) setting (bar)
SETTING:
Standard type, for 4 positions regenerative circuit (spool type 8Y)
50 bar (725 psi) 63 bar (914 psi) 80 bar (1150 psi)
With integrated connectors
8EZ3T-12VDC 5V08130874 With AMP connector
8EZ34-12VDC 5V08130872 With Deutsch connector
8EZ4-24VDC 5V08130873 With Deutsch connector
Proportional controls with on-board electronic ........... page 33
With absolute output signal (0.5-4.5 V)
8ZW3F-12VDC 5V0814090A With flying leads
8ZW3F-24VDC 5V0814091A With flying leads 6 L.S. port relief valves page 37
8ZW3FD-12VDC 5V0814090D With Deutsch connector Standard setting is referred to 10 l/min - 2.6 US gpm flow.
8ZW3FD-24VDC 5V0814091D With Deutsch connector TYPE CODE DESCRIPTION
With ratiometric output signal (25%-75% Vbb) LSD XCAR126215 With blind nut, range 40-180 bar /
8ZW3P-12VDC 5V08140902 With flying leads 580-2600 psi, std. setting 90 bar / 1300 psi
8ZW3P-24VDC 5V08140910 With flying leads XCAR126213 As previous, range 180-350 bar /
8ZW3PD-12VDC 5V08140905 With Deutsch connector 2600-5100 psi std. setting 180 bar / 2600 psi
8ZW3PD-24VDC 5V08140913 With Deutsch connector LSH XCAR126216 With locked arrangement, range 40-180 bar
With feedback and absolute output signal (0.5-4.5 V) / 580-2600 psi, std. setting 90 bar / 1300 psi
8ZR4F-12VDC 5V0813090A With flying leads XCAR126217 As previous, range 180-350 bar /
8ZR4F-24VDC 5V0813091A With flying leads 2600-5100 psi, std. setting 180 bar / 2600 psi
8ZR4FD-12VDC 5V0813090D With Deutsch connector LSZ 5CAR126221 With anti-tamper cap, range 40-180 bar
8ZR4FD-24VDC 5V0813091D With Deutsch connector / 580-2600 psi, std. setting 90 bar / 1300 psi
With feedback and ratiometric output signal (25%-75% Vbb) 5CAR126219 As previous, range 180-350 bar /
8ZR4P-12VDC 5V08130902 With flying leads 2600-5100 psi, std. setting 180 bar / 2600 psi
8ZR4P-24VDC 5V08130910 With flying leads ST 5KIT126210 Relief valve blanking plug
8ZR4PD-12VDC 5V08130905 With Deutsch connector
8ZR4PD-24VDC 5V08130913 With Deutsch connector
7 Section threading
8 Plug for single acting spool*

CODE DESCRIPTION
NOTE (*): Codes are referred to BSP thread. 3XTAP727180 G1/2 plug
D1WWED02E 21
DPC130 DPC Series
Working section __________________________________________________________________________________________
With compensator
Type C10 Type C13

without port valves without port valves with upper L.S port
LSAB
0.43
11
69.5
2.74
126.5
4.98
130.4
5.13
12
0.47 lever side
B
71.5
2.81
11.8
0.46
0.39
39.5
10
1.56
A
LSAB'
0.157
33 41.5
4
1.30 1.63 lever side

8
B
0.315
0.63 0.63
1.89
16
48
Type C22
A with arrangement for port valves and L.S. relief valve
16
L.S. valve 86 15
on port B 3.39 0.59 Port B valve
8
0.315 B
40 116
0.47
12
1.413
1.57 4.57
1.42
35.9
36
A
79 18.5
0.476
L.S. valve
12.1
Port A valve
3.11 0.73
on port A
Type C10 Type C13 Type C22

B A LSAB’ B A B A
LSAB LSAB LSAB
22 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
With compensator
Type C24 Type C21 Type C23

Type C20 As type C20 with with arrangement for port As type C21 with
with port valves arrangement upper L.S. port valves and one L.S. relief valve upper L.S. port
B A LSAB’ B A B A LSAB’ B A
LSAB LSAB LSAB LSAB
Type F10 Type F20 Type CM23

for floating circuit without for floating circuit with for regenerative circuit with arrangement
port valves arrangement port valves arrangement for port valves and one L.S. relief valve
B A B A B A
LSAB LSAB LSAB
D1WWED02E 23
DPC130 DPC Series
Working section __________________________________________________________________________________________
Without compensator Without compensator, with check valve

Dimensions are the same of types with compensator. Dimensions are the same of types with compensator.
See page 20 for section configuration list, and pages 22-23 See page 20 for section configuration list, and pages 22-23
for circuit representation. for circuit representation.
3.5
0.138
Type D10 Type CV10

without port valves arrangement without port valves arrangement
B A B A
LSAB LSAB
24 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
Spools
Spool type 1 Spool type 2 Spool type 2H

A, B closed in neutral position A, B open to tank in neutral pos. A, B partially to tank in neutral pos.
2 0 1 2 0 1 2 0 1
B A B A B A
T T T
P P P
Spool stroke Spool stroke Spool stroke
position 1: + 7 mm (+ 0.28 in) position 1: + 7 mm (+ 0.28 in) position 1: + 7 mm (+ 0.28 in)
position 2: - 7 mm (- 0.28 in) position 2: - 7 mm (- 0.28 in) position 2: - 7 mm (- 0.28 in)
Spool type 3 Spool type 5 Spool type 8F

single acting on A floating in 4th position (pos.3) regenerative in 2nd position (pos.1)
2 0 1 2 0 1 3 2 0 1
B A B A B A
T T T
P P P
position 3: + 12 mm (+ 0.47 in)
Spool type 8Y
regenerative in 4th position (pos.3)
2 0 1 3
B A
P
Spool stroke
position 1: + 4.5 mm (+ 0.18 in)
position 2: - 4.2 mm (- 0.17 in)
position 3: + 7.8 mm (+ 0.31 in)
D1WWED02E 25
DPC130 DPC Series
Working section __________________________________________________________________________________________
Spools
Following curves are detected with standard spools, connecting P⇒A⇒B⇒T and P⇒B⇒A⇒T ports without flow multiplication.
Customized spools with backpressure or flow multiplication may require different force, pressure and pilot current for
operation.
Metering curves
Compensated working section - 3 positions spools
Qin = 150 l/min (39.6 US gpm)
217.5 200 160 120 80 72.5 0 72.5 80 120 160 200 217.5
(psi)
-0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 (in)
150
(US gpm)
(l/min)
120 32
P P
N N
24
Port flow
90
S S
60 16
Q Q
V V
30 8
D D
C C
0 0
-7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 (mm)
position 2 Spool stroke position 1
Pilot pressure
(bar)
With 8IM
15.0 12.5 10.0 7.5 5.0 0 5.0 7.5 10.0 12.5 15.0
control kit
Current (mA@12VDC)
1000 900 800 700 600 500 0 500 600 700 800 900 1000
With 8EZ3 and
8EZ3T control kit (mA@24VDC)
500 450 400 350 300 250 0 250 300 350 400 450 500
Voltage
(V)
With 8ZW3F and
4.5 4.0 3.5 3.0 2.8 2.5 2.2 2.0 1.5 1.0 0.5
8ZR4F control kit
Battery voltage (% Vbb)

With 8ZW3P and
75% 70% 65% 60% 55% 53% 50% 47% 45% 40% 35% 30% 25%
8ZR4P control kit
Non-compensated working section

Spool flow vs. Stand-by pressure
(margin pressure)
0 80 160 240 320 (psi)
160
102 P
N 40
(l/min)
(US gpm)
S Spool nominal flow @ 7 bar (102 psi)
120
30 stand-by (margin pressure)
Port flow
Q C = 5 l/min (1.3 US gpm)

80 D = 10 l/min (2.6 US gpm)
20
V V = 25 l/min (6.6 US gpm)
Q = 40 l/min (10.6 US gpm)
40 D 10 S = 60 l/min (15.9 US gpm)
C N = 80 l/min (21.1 US gpm)
P = 100 l/min (26.4 US gpm)
0 0
0 5 10 15 20 25 (bar)
7 Pressure
26 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
"A" side spool control kit
With friction and center position feeling: type 7FT

17.5
0.69
X Z
1 0 2
71.5
2.81
Features
113.5 X = wrench 24 - 42 Nm (31 lbf) Friction load adjusting . . . . : 20-150 N (4.5-34 lbf)
4.47
Y = allen wrench 6 Friction load std. setting . . : 100 N (22.5 lbf)
Z = wrench 13 - 24 Nm ( 17.7 lbf) Center tap (more than load) : 100 N (22.5 lbf)
With spring return to neutral position: type 8

16
0.63 Force vs. Stroke diagram
0 -0.05 -0.1 -0.15 -0.2 -0.25 -0.3 (in)
(N) 0 0.05 0.1 0.15 0.2 0.25 (in)

500 (lbf)
100
1 0 2 400
75
300
Force
71.5
2.81
50
200
25
100
0 0
0 1 2 3 4 5 6 7 pos.1 (mm)
0 -1 -2 -3 -4 -5 -6 -7 pos.2 (mm)
Stroke
= 93.4 N @ 2 mm (21 lbf @ 0.079 in)

118 N @ 7 mm (26.5 lbf @ 0.28 in)
= 132 N @ 2 mm (29.6 lbf @ 0.079 in)
368 N @ 7 mm (82.7 lbf @ 0.28 in)
With detent in 4th position (pos.3), for floating circuit: type 13

Need working sections type F, G or FV and floating circuit spools type 5.
10.5
0.41
3 1 0 2
71.5
2.81
Features
X Detent force (±10%) . . . . . : 310 N (70 lbf)
Release force (±10%) . . . . : 110 N (24.7 lbf)
45.5
X = wrench 13 - 24 Nm ( 17.7 lbf)
1.79
D1WWED02E 27
DPC130 DPC Series
Working section __________________________________________________________________________________________
Proportional hydraulic controls

31
1.22
G1/4
nr.2 threads VB
1.06
27
VA VA VB
1 0 2
71.5
71.5
2.81
2.81
Features
Max. pressure . . . . . . . . . . . . . : 50 bar (725 psi)
24
0.94
48
1.89
Suggested pressure
Stroke vs. Pressure diagram control curve: type 020
-0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 (in) 0 0.05 0.10 0.15 0.20 0.25 0.3 (in)
20 (psi) 40 (psi)
35 bar - 508 psi
(bar) 250 (bar) 500
15 30
Pilot pressure
200 400
Pressure
10 150 20 300
0.30 in
spool 15.3 bar - 220 psi
dead band 100 200
7.6 mm -
5
7.25 mm
10 4.3 bar
50
0.29 in
63 psi 100
0.85 mm
0 0 0.033 in
0 0
-7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 (mm) 0 2 4 6 8 (mm)
position 2 Stroke position 1 Pusher stroke
28 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
Electrohydraulic controls: without on-board electronic
Following specifications are measured with:

• mineral oil of 46 mm2/s - 46 cSt viscosity at 40°C - 104°F temperature,
• 20°C - 60°F environmental temperature,
• standard spools, connecting P⇒A⇒B⇒T ports without flow multiplication,
• 12 VDC and 24 VDC nominal voltage with tolerance ± 10%.
Standard spool Regenerative spool Floating spool

Specifications
control type control type control type
8EZ3 8EZ3T 8EZ3CR (8Y)13EZ3 13EZ3
Electric specifications
12 VDC 6.7 Ω 4.7 Ω 6.7 Ω 6.7 Ω 6.7 Ω

Coil impedance
24 VDC 24.7 Ω 20.8 Ω 24.7 Ω 24.7 Ω 24.7 Ω
Max. operating 12 VDC 1.79 A 1.50 A 1.79 A 1.79 A 1.79 A

current 24 VDC 0.97 A 0.75 A 0.97 A 0.97 A 0.97 A
No load current consumption - - - - -
Hysteresis max. (1)

external drain 10% 10% 10% 10% 10%
from 0 ⇒ 100% and
Time response from 100% ⇒ 0 < 150 ms < 150 ms < 150 ms < 150 ms < 150 ms
of stroke
Min. flow control 12 VDC 500 mA 500 mA 560 mA 560 mA 220 mA

signal 24 VDC 250 mA 250 mA 280 mA 280 mA 110 mA
Max. flow 12 VDC 1000 mA 1000 mA 800 mA 800 mA 560 mA

control signal 24 VDC 500 mA 500 mA 400 mA 400 mA 280 mA
Min. Regenerative 12 VDC - - - 1100 mA -

flow control signal 24 VDC - - - 550 mA -
Max. Floating/ 12 VDC - - - 1300 mA 900 mA
Regenerative flow
control signal 24 VDC - - - 650 mA 450 mA
Dither frequency high frequency 150 Hz (200 mA) 100 Hz (200 mA) 150 Hz (200 mA)
Insertion 100% 100%

Class F Class H
Coil insulance Class F (155°C - 311°F)
(155°C - 311°F) (180°C - 356°F)
ISO4400
AMP JPT
Connector type Flying leads ISO4400
Deutsch DT
Deutsch DTM
IP65 (type
IP65 (type JPT)
Weather protection (connector) ISO4400) IP65
IP69K (type DT)
IP69K (type DTM)
Hydraulic specifications
Max. pressure 50 bar (725 psi) 50 bar (725 psi)
Max. back pressure 2.5 bar (36 psi) 2.5 bar (36 psi)
Note (1) For the calculation rules see "Appendix A" on page 71.
Listed electrohydraulic controls need CED100X or CED400X electronic control unit; for information contact Sales Department.
D1WWED02E 29
DPC130 DPC Series
Working section __________________________________________________________________________________________
Spool stroke vs. pilot current diagrams
Types 8EZ3 - 8EZ4 - 8EZ4D - 8EZ3T

-0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 (in)
1400 700
(mA@12VDC) spool (mA@24VDC)
dead band
1050 525
1000 /500 mA
Current
700 350
500 /250 mA
350 175
0 0
-7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 (mm)
position 2 Stroke position 1
Types 13EZ3 - 13EZ4: for floating circuit

-0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 (in)
1400 700
(mA@12VDC) (mA@24VDC)
1050 525
spool C
dead band
Current
700 350 Ref. Current (mA) Stroke

E B 12VDC 24VDC mm (in)
A 220 110 2 (0.079)
350 175 B 560 280 7 (0.276)
C 900 450 12 (0.472)
D A D 220 110 -2 (-0.079)
0 0 E 560 280 -7 (-0.276)
-7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 9 10 11 12 (mm)
position 2 Stroke position 1 position 3
Type 8EZ3CR: for regenerative circuit

-0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 (in)
1400 700
dead band
1050 525
Current
800 / 400 mA
700 350
560 /280 mA
350 175
0 0
-7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 (mm)
Type (8Y)13EZ3: for regenerative circuit

-0.3 -0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 0.3 (in)
1400 700
D
dead band C
1050 525
B
Current
Ref. Current (mA) Stroke

700 F 350 12VDC 24VDC mm (in)
400 / 200 mA A A 560 280 2 (0.079)
280 /140 mA B 850 425 4.5 (0.177)
350 E 175 C 1100 550 6 (0.236)
D 1300 650 7.8 (0.307)
E 440 210 -1 (-0.039)
0 0 F 800 405 -4.2 (-0.165)
-8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 (mm)
position 2 Stroke position 1 position 3
30 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
Proportional controls, types 8EZ - 13EZ

Control Types
1 : With ISO4400 connector - mating connector code: 2X1001030
2 : With flying leads
3 : With Deutsch DTM04 connector - mating connector Deutsch DTM06 code: 5CON140025
844 800
33.23 31.50
3 2 1
Types
8EZ3 - 8EZ4
8EZ4D - 8EZ3CR
coil 2
1 0 2
174.5
174.5
6.87
169.5
6.87
6.67
coil 1
Types
13EZ3 - 13EZ4
71.5
2.81
(8Y)13EZ3 coil 2
coil 1
3 1 0 2
58
2.28
ISO4400 connector Deutsch DTM04 connector
4 1
3
2 1 3 2
GND
Magnet must be assembled

Connectors with this side (printed side)
Wire colour Function
pin facing the section side
without O-ring seating
1 blue common (-)
2 red Coil 2 - Port B
3 green Coil 1 - Port A
4 - Plugged
D1WWED02E 31
DPC130 DPC Series
Working section __________________________________________________________________________________________
Proportional control type 8EZ3T

Control Types
1 : With AMP JPT connector - mating connector AMP JPT, code: 5CON003
2 : With Deutsch DT04 connector - mating connector Deutsch DT06-2S code: 5CON140031
2
181.5
EVA EVB
7.15
port A port B
168.5
6.63
EVA EVB
1 0 2
71.5
2.81
A
B
70
2.76
32 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
Electrohydraulic controls: with on-board electronic

Specifications Spool control type

8ZW3F 8ZW3P 8ZR4F 8ZR4P
12 VDC - - - -
Coil impedance
24 VDC - - - -
Max. operating 12 VDC - - - -

current 24 VDC - - - -
No load current consumption < 150 mA < 150 mA < 150 mA < 150 mA
Hysteresis max. (1)

external drain 10% 10% < 1% < 1%
from 0 ⇒ 100% and
Time response from 100% ⇒ 0 of < 150 ms < 150 ms < 150 ms < 150 ms
stroke
Min. flow control 12 VDC 2.2 V (port A) 47% (port A) 2.2 V (port A) 47% (port A)
signal 24 VDC 2.7 V (port B) 53% (port B) 2.7 V (port B) 53% (port B)
Max. flow 12 VDC 0.5 V (port A) 25% (port A) 0.5 V (port A) 25% (port A)
control signal 24 VDC 4.5 V (port B) 75% (port B) 4.5 V (port B) 75% (port B)
Float flow 12 VDC - - - -

control signal 24 VDC - - - -
Dither frequency high frequency - - - -
Insertion 100% 100%
Coil insulance Class F (155°C - 311°F) Class F (155°C - 311°F)
Connector type Flying leads - Deutsch DTM Flying leads - Deutsch DTM
Weather protection (connector) IP69K (type DTM) IP69K (type DTM)
Max. back pressure 2.5 bar (36 psi) 2.5 bar (36 psi)
Note (1) For the calculation rules see "Appendix A" on page 71.
D1WWED02E 33
DPC130 DPC Series
Working section __________________________________________________________________________________________
Spool stroke vs. pilot current diagrams
Types 8ZW3F - 8ZR4F

-0.3 -0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 0.3 (in)
(V) 5
4.5 V spool
dead band
4
2.8 V
Current
3
2.5 2.2 V
2
1
0.5 V
0
-7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 (mm)
Types 8ZW3P - 8ZR4P

-0.3 -0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 0.3 (in)
100
(% of Vbb) spool
dead band
80 75%
Current
60
53%
50
47%
40
25%
20
0
-7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 (mm)
34 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
Proportional controls type 8ZW3 (all configurations)

Control Types
180.5
7.11
3 4
1 0 2
71.5
2.81
2 1
Pin Wire colour Function
RS232 RX
1 white
joystick
1
2 brown Vbb
440
17.32 3 yellow GND
15 95
2 0.59 3.74 4 green RS232 TX
440
17.32
Proportional controls type 8ZR4 with feedback (all configurations)

Control Types
7.87
200
3 4
1 0 2
71.5
2.81
2 1
Pin Wire colour Function
440
17.32 1 white Joystick
2 brown Vbb
1
3 yellow GND
2 4 green Alarm
440 113
17.32 4.45
D1WWED02E 35
DPC130 DPC Series
Working section __________________________________________________________________________________________
"B" side spool control kit
Aluminium lever box; type L Aluminium lever box, without lever; type LN
3 1 0 2 3 1 0 2
21
42 45° 6 0
°3
1.65 0'
16
30
°3
°
0'
1
3
Dimensions are the
same of type L
71.5
2.81
1.85
1.55
47
39
Z Y X
87
3.43 X = allen wrench 3
Y
Y = wrench 10
B 9.8 Nm - 7.2 lbf
B
0.83
X Z = allen wrench 4
21
6.6 Nm - 4.9 lbf wrench 8
M8
15° 0
30
°
1
30
°
Lever assembly position

2 See page 20 for specification
in working section description
30°
3
°
30
Alum. lever box, with anti-tamper cap; type LZ Cast iron lever box; type LG
3 1 0 2 3 1 0 2
99.5
3.92
Other dimensions and Dimensions and lever

lever positions are the positions are the same
same of type L of type L
Anti-tamper cap
code: 4COP116420
36 D1WWED02E
DPC Series DPC130
___________________________________________________________________________________________
Working section
Port valves
D
Type U Type C Type UT

antishock valve anticavitation valve valve blanking plug
X X X
5.55
141
X = wrench 13
24 Nm - 17.7 lbf
Type U, setting example Types U-C, pressure drop

(10 l/min - 2.6 Us gpm) (in anticavitation)
A 0 5 10 15 20 25 (US gpm)
0 5 10 15 20 25 (US gpm)
1.413
400 40
35.9
340 bar - 4950 psi (psi) (psi)

B (bar) 5000
(bar)
500
300 270 bar - 3900 psi 30
79 18.5 4000 400
0.476
12.1
Pressure
Pressure
3.11 0.73 210 bar - 3050 psi
200 3000 20 300
140 bar - 2050 psi eC
Typ
2000 200
Valve Dim. D 100
80 bar - 1150 psi
10 U
ype 100
type mm in 25 bar - 360 psi 1000 T
U 10.5 0.41 0 0 0 0
0 20 40 60 80 100 (l/min) 0 20 40 60 80 100 (l/min)
C 10.5 0.41 Flow Flow
UT 7.5 0.30
L.S. port relief valves
Valve on Valve on
port B port A
E
Type LSH Type LSD Type ST

with lock arrangement with blind nut valve blanking plug
W K
Z
Y Y
X X J
5.55
141
J J
Type LSZ
with anti-tamper cap
cap parts Pressure vs. flow diagram
B 4COP116240 (1) = valve range 40-180 bar (580-2600 psi)
(2) = valve range 180-350 bar (2600-5000 psi)
0.47
X
12
1.42
0 5 10 15 20 25 (US gpm)
36
A 400
max. setting (2) (psi)
(bar)
5000
86 15 J
300 medium range setting (2)
3.39 0.59 4000
Pressure
200 max. setting (1) min. and std. setting (2) 3000
Valve Dim. E X = wrench 13 / 42 Nm - 31 lbf
2000
type Y = wrench 10 / 9.8 Nm - 7.2 lbf std. setting (1)
mm in 100
W = allen wrench 3 1000
LSD 21.5 0.85 min. setting (1)
Z = wrench 10 / 9.8 Nm - 7.2 lbf
LSH 17 0.67 J = wrench 7 / 24 Nm - 17.7 lbf 0 0
0 20 40 60 80 100 (l/min)
LSZ 34 1.34 K = allen wrench 5 / 24 Nm - 17.7 lbf
Flow
D1WWED02E 37
DPC130 DPC Series
Outlet section parts ordering codes ________________________________________________________________
DPC130/RD 3 1 - ......
1 2 3 4
2
1 Outlet section body * page 39 . 3 Ports options *

TYPE CODE DESCRIPTION TYPE CODE DESCRIPTION
RF 3FIA731000 Without ports 0 - Without ports; for RF section
RC 3FIA731310 With ports P1 and T1 1 3XTAP732200 G3/4 plug (nr.2); ports P1 and T1 pluggd
RD 3FIA731320 With ports P1, T1 and LS1 2 3XTAP732200 G3/4 plug (nr.1); port P1 plugged and T1
open
2 Drain options page 39 3 3XTAP732200 G3/4 plug (nr.1); port P1 open and T1
plugged
TYPE CODE DESCRIPTION 4 - Ports P1 and T1 open
1 XTAP517460 Internal drain; to use with mechanical
controls
2 XTAP217160 Internal drain; to use with hydraulic
4 Section threading
controls Specify only if it is different from BSP standard (see page 5).
3 XCAR119611* External drain G1/4; for electrohydralic
controls
38 D1WWED02E
DPC Series DPC130
______________________________________________________________________________________________
Outlet section
Type RD31 Type RC31

With ports P1, T1 (plugged) and LS1. With ports P1, T1 (plugged).
External drain External drain
L
T1 T1
max. 144.5
max. 5.69
125.5
4.94
P1 P1
LS1 Type RD31 Type RC31 Type RF30
71.5
2.82
T1 T1
0.366
9.3
1.89
48
1.46
37
9
0.354
P1 P1
42 86 Type RF30 L
1.65 1.42 Without ports, external drain
115.5 L
L
4.55 L
12.7
0.50
1.26
32
L
20.1
0.80
0.21.7
5.5
100 8
3.94 0.315
Note: The port LS1 must not be plugged
(in case it’s not used it has to be connected LS1
to tank).
Drain options
Option 1
internal drain for
F
mechanical controls
Option 1 Option 2 Option 3
allen wrench 5
24 Nm - 17.7 lbf
125.5
4.94
L
Option 2
internal drain for
hydraulic controls
allen wrench 6
24 Nm - 17.7 lbf
Dim. F
Option
mm in Option 3
external drain for
1 3.5 0.138
electrohydraulic controls
2 3.5 0.138
3 19 0.75 wrench 19
24 Nm - 17.7 lbf
D1WWED02E 39
DPC200 DPC Series
Dimensional data and performance ________________________________________________________________
182.5 E
7.19
170 1.6 53 75
6.69 0.063 2.09 2.95
3.23
82
64.5
2.54
V1
L
36.5
1.44
0.98
25
V2 A2 A1
P
28.25
28.25
1.112
M
1.112
398.3
15.68
8.15
207
2.68
5.28
70.5
134
2.78
68
T
M12
37.75
1.486
35.25
1.388
B2 B1
19.25
0.758
36.5
1.44
6 36.5 21.5
0.236 1.44 0.85
93
3.66
189.5 F
7.46
E F Weight E F Weight
TYPE TYPE
mm in mm in Kg lb mm in mm in Kg lb
DPC200/1 177 6.97 220 8.66 39.5 87.1 DPC200/6 442 17.40 485 19.09 111 245
DPC200/2 230 9.06 273 10.75 53.8 117 DPC200/7 495 19.49 538 21.18 125 276
DPC200/3 283 11.14 326 12.83 68.1 150 DPC200/8 548 21.57 591 23.27 140 308
DPC200/4 336 13.23 379 14.92 82.4 182 DPC200/9 601 23.66 644 25.35 154 339
DPC200/5 389 15.31 432 17.01 96.7 213 DPC200/10 654 25.75 697 27.44 168 371
P⇒T Pressure drop inlet compensator A(B)⇒T pressure drop

(margin pressure) (standard spool @ max.stroke)
0 10 20 30 40 50 60 (US gpm) 0 10 20 30 40 50 60 (US gpm)
20 60
(psi) (psi)
(bar) (bar)
250 750
15 45
200 600
Pressure
Pressure
10th section
10 150 30 450
5th section
100 300
5 15
50 150
1st section
0 0 0 0
0 40 80 120 160 200 240 (l/min) 0 40 80 120 160 200 240 (l/min)
Flow Flow
40 D1WWED02E
DPC Series DPC200
__________________________________________________________________________________________
Hydraulic circuit
Open center configuration example
B2 A2 B1 A1
P T
M
V2
L
V1
VB2 VB1
LS
VA2 VA1
Open center circuit and proportional hydraulic control with lever, with unloader
valve and port valves arrangement
Closed center configuration example
B2 A2 B1 A1
P T
M
V2
L
V1
EVB2
EVB1
LS
EVA2 EVA1
LSA LSB LSA LSB

Closed center circuit and one-side proportional electrohydraulic control with
lever, with unloader valve and pressure reducing valve, anticavitation valves on
all ports, L.S. relief valves on 2th section, LSA and LSB ports, internal pilot and
external drain
D1WWED02E 41
DPC200 DPC Series
Complete sections ordering codes __________________________________________________________________
DPC200/2/ BR2-10(H220\ELP) / C21-104(200\200)-8EZ3TLG1.U100U320 /...... / RF30-......-12VDC-<SB20-CVN>
Valve type 1 2 3 4 5 6
Nr. of working sections The valve is supplied painted,

as standard, with one coat of
Primer black antirust paint
7
2
42 D1WWED02E
DPC Series DPC200
1 Inlet section * page 44 4 Valve threading

Closed Center circuit Specify threading only if it is different from BSP standard (see page
TYPE: DPC200/BR2-10(H220\ELP)-12VDC CODE: 638203001 5).
DESCRIPTION: With 3-way compensator, L.S. pressure relief valve For valve with ISO 6162-1 type 1 flange connection digit: FS3-
and 12VDC solenoid operated unloader valve, with P-T-LS ports open M(BSP).
TYPE: DPC200/BRF2-30(H220\ELP)-12VDC CODE: 638203002
DESCRIPTION: Without compensator, with L.S. pressure relief valve 5 Voltage
and 12VDC solenoid operated unloader valve, with P-T-LS ports open
Open Center circuit Specify the voltage of electric devices.
TYPE: DPC200/BR1-10(H220\ELP)-12VDC CODE: 638203003
DESCRIPTION: With 3-way compensator, L.S. pressure relief valve 6 Pump stand-by
and 12VDC solenoid operated unloader valve, with P-T-LS ports open This option must be specified only if valve is configured for Closed
Center circuit, without local compensation and if the value is different
2 Working section * page 50 from 11.5 bar (167 psi)
TYPE: DPC200/C10-104(200\200)-8EZ3TLG1-12VDC
CODE: 638103001 7 Assembling kit
DESCRIPTION: With 2-way compensator, double acting spool for CODE CODE DESCRIPTION
200 l/min (52.8 US gpm), prop. electrohydraulic control with lever. With inlet section type
TYPE: DPC200/F32-504(200\200)-8EZ3TLG1.ULTULT.STST-12VDC Type BR Type BRF
CODE: 638103002 5TIR112215 5TIR112175 For 1 working section valve
DESCRIPTION: With 2-way compensator, floating spool for 200 l/min 5TIR112268 5TIR112228 For 2 working sections valve
(52.8 US gpm), prop. electrohydraulic control with lever, arranged for 5TIR112321 5TIR112281 For 3 working sections valve
"UL" size valves and L.S. relief valves, with LSA-LSB ports 5TIR112374 5TIR112334 For 4 working sections valve
3 Outlet section * page 63 5TIR112480 5TIR112440 For 6 working sections valve
For valve with mechanical control 5TIR112533 5TIR112493 For 7 working sections valve
TYPE: DPC200/RF10 CODE: 638303001 5TIR112586 5TIR112546 For 8 working sections valve
DESCRIPTION: Without ports 5TIR112639 5TIR112599 For 9 working sections valve
For valve with hydraulic control 5TIR112692 5TIR112652 For 10 working sections valve
TYPE: DPC200/RF20 CODE: 638303002
DESCRIPTION: Without ports, internal drain
TYPE: DPC200/RD21 CODE: 638303004
DESCRIPTION: With port P1, T1 (plugged) and LS1, internal drain
For valve with electrohydraulic control
TYPE: DPC200/RF30 CODE: 638303003
DESCRIPTION: Without ports, external drain L
TYPE: DPC200/RD31 CODE: 638303005
DESCRIPTION: With port P1, T1 (plugged) and LS1, external drain L NOTE (*): Codes are referred to BSP thread.
D1WWED02E 43
DPC200 DPC Series
Inlet section parts ordering codes _________________________________________________________________
Valve setting (bar)
DPC200 / BR1 - 1 0 (H220\ELP\......\SB15)-......-12VDC DPC200/BR2 - 1 0 (H220\ELP\......)-......-12VDC
1 2 3 5 6 7 4 8 9 1 2 3 5 6 7 8 9
5 5
7 7
1 1
6 6
9 9
DPC200/BRF2 - 3 0 (H220\ELP\......)-......-12VDC
1 2 3 5 6 7 8 9
Circuit conversion kit

6
9
7
10
44 D1WWED02E
DPC Series DPC200
___________________________________________________________________
Inlet section parts ordering codes
1 Inlet section body kit* page 46 6 Solenoid operated unloading valve page 48
Open Center circuit Needs coil type BER: see chapter 9
TYPE: DPC200/BR1-1 CODE: 5FIA620302 TYPE CODE DESCRIPTION
DESCRIPTION: With compensator, pressure reducing valve ELN 0EC08002031 Without emergency override
arrangement, P-T-LS ports (LS plugged), arranged for unloader valve ELP 0EC08002033 With push-button emergency override
TYPE: DPC200/BR1-1-FS3-M(BSP) CODE: 5FIA620303 ELT 0EC08002035 With “twist & push” emergency override
DESCRIPTION: As previous, with ISO 6162-1 type 1 flange connector ELV 0EC08002034 With screw type emergency override
Closed Center circuit LT XTAP225320 Unloading valve blanking plug
TYPE: DPC200/BR2-1 CODE: 5FIA620304
DESCRIPTION: With compensator, pressure reducing valve 7 Pressure reducing valve page 48
arrangement, P-T-LS ports, arranged for unloader valve
TYPE: DPC200/BR2-1-FS3-M(BSP) CODE: 5FIA620305 TYPE CODE DESCRIPTION
DESCRIPTION: As previous, with ISO 6162-1 type 1 flange connect. - 4AC9539900 Pressure reducing valve, 32 bar / 464 psi
TYPE: DPC200/BRF2-3 CODE: 5FIA620306 RT 3XTP3535100 Valve blanking plug (SAE 08/3)
DESCRIPTION: Without compensator, with pressure reducing valve
arrangement, P-T-LS ports, arranged for unloader valve 8 Section threading
TYPE: DPC200/BRF2-3-FS3-M(BSP) CODE: 5FIA620307 Specify threading only if it is different from BSP standard.
DESCRIPTION: As previous, with ISO 6162-1 type 1 flange connect. For section with ISO 6162-1 type 1 flange connection digit: FS3-
M(BSP).
2 Port arrangement
TYPE DESCRIPTION 9 Coil
1 With upper T and P ports (for section BR) TYPE CODE DESCRIPTION
3 With side T and P ports (for section BRF) 12VDC 4SLE001200 Coil type BER, ISO4400 conn., 12VDC
For complete available coils list see page 68.
3 Port options
TYPE DESCRIPTION 10 Circuit conversion kit
0 Ports P and T open These kits ara available only for BR section; not for BRF section.
1 Port P open, port T plugged CODE DESCRIPTION
XSTR117790 For circuit conversion from Open Center to Closed
4 Compensator stanb-by Center
Specify value only if it's different from the standard (11.5 bar / 167 5KIT200310* Kit for circuit conversion from Closed Center to Open
psi): for Open Center sections Center
5 L.S. relief valve page 49

Standard setting is referred to 10 l/min - 2.6 US gpm flow.
LSD XCAR126215 With blind nut, range 40-180 bar /
2600-5100 psi std. setting 180 bar / 2600 psi
LSH XCAR126216 With locked arrangement, range 40-180 bar
LSZ 5CAR126221 With anti-tamper cap, range 40-180 bar
5CAR126219 As previous, range 180-350 bar /
ST 5KIT126210 Relief valve blanking plug NOTE (*): Codes are referred to BSP thread.
D1WWED02E 45
DPC200 DPC Series
Inlet section ______________________________________________________________________________________________
Example of BR section type
V2
M
max. 202
max. 7.95
LS V1
6.69
170
132.5
5.22
126.5
4.98
LS
4.37
111
3.66
3.50
93
89
78.5
3.09
1.85
47
5 19.25 19.25 8.75

0.63
0.47
0.197 0.758 0.758 0.344

16
12
23.75
0.935
36.5 134
1.44 5.28 M12 nr.2 threads
Auxiliary ports specification 9.75 35.25 70.5 28.25
M = G1/4 pressure gauge connection 0.384 1.388 2.78 1.112
48.5
1.91
T
valves feeding (P⇒OUT) P
0.71
3.35
18
85
V2 = M14x1.5 pilot pressure port for
electrohydraulic controls optional feeding
0.098
(Pmax = 315 bar / 4600 psi) (P⇒IN):
0.236
2.5
6
needs G1/4 joint, code 5GIU519611.
21.5
0.85
LS
207 82
8.15 3.23
max. 380
max. 14.96
Closed center Open center

configuration example configuration example
BR2-10(H220\ELN) BR1-10(H220\ELN) FS3-M(BSP) optional connection
35.25 70.5
1.39 2.78
P T P T
13.1
0.52
11.1
0.44
M M T P
V2 V2
26.2
22.2
1.03
0.87
0.24
V1 V1
6
26.2 23.8
0.94 M10
1.03
nr. 4+4 threads
LS 52.4 47.6
2.06 1.87
LS
LS
46 D1WWED02E
DPC Series DPC200
________________________________________________________________________________________________
Inlet section
Example of BRF section type
M
6.34
161
152.5
6.00
4.29
P
109
3.23
LS
80.5
82
3.17
64.5
2.54
2.28
58
1.85
47
34.5
1.36
7.1 4 15
0.63
0.47
0.280 0.157 0.59

16
12
89 17.25 95.5 21.25

3.50 0.679 3.76 0.837
max. 323
max. 12.72
36.5 134
20.1
0.79
1.44 5.28
M = G1/4 pressure gauge connection
V1
49.5
1.95
max. 135
max. 5.31
0.23
5.9
valves feeding (P⇒OUT)

18.5
0.73
11.1
0.44
15
0.59
207 82
8.15 3.23
Configuration Configuration FS3-M(BSP) optional connection

BRF2-30(H220\ELN) BRF2-30(H220\ELT\RT)
52.4 47.6
2.06 1.87
M10 26.2 23.8
P T P T nr. 4+4 threads 1.03 0.94
13.1
0.52
M M
T
26.2
1.03
M
V1 V1
P
4.29
109
22.2
0.87
LS
38.6
1.52
11.1
0.44
LS LS
17.25 89 27.75
0.689 3.50 1.093
D1WWED02E 47
DPC200 DPC Series
Inlet section _______________________________________________________________________________________________
Pressure reducing valve
Type RT Reduced pressure vs. Flow

Pressure reducing valve valve blanking plug
0 0.8 1.6 2.4 3.6 (US gpm)
60
2 1 (bar) 800
3 1
(psi)
Reduced pressure
2 3 45
wrench 24 600
wrench 24
30 Nm - 22 lbf
30 Nm - 22 lbf 30
400
On BR section
On BRF section 15 200
0 0
0 3 6 9 12 15 (l/min)
82 Flow
3.23
82
3.23
Features
Reduced press. range . : from 3.5 to 35 bar
: from 50 to 500 psi
Max. inlet pressure . . . : 420 bar - 6100 psi
Nominal flow . . . . . . . : 15 l/min - 4 US gpm
118.5 118.5
4.67 4.67
Solenoid operated unloading valve
Type ELN: without emergency Type ELP: push button type On BR section
wrench 24
30 Nm - 22 lbf On BRF section
1 1
2 2
A
1 1
C
2 2
Type ELV: screw type Type ELT: “push & twist” type
1 1
2 2
1 1
B D
2 2
LT: valve blanking plug
allen wrench 10
24 Nm - 17.7 lbf BR section BRF section
Valve
A B C D
type
mm in mm in mm in mm in
Features
Max. flow . . . . . . . . . . . . . . . . : 40 l/min - 10.6 US gpm ELN 65.5 2.58 102 4.02 60 2.36 89 3.50
Max. pressure . . . . . . . . . . . . . : 380 bar - 5500 psi ELP 88.5 3.48 125 4.92 83 3.27 112 4.41
Internal leakage . . . . . . . . . . . : 0.25 cm3/min @ 210 bar
ELV 88.5 3.48 125 4.92 83 3.27 112 4.41
0.015 in3/min @ 3050 psi
For coil features and options see coil BER at page 68.
ELT 91 3.58 127.5 5.02 85.5 3.37 114.5 4.51
48 D1WWED02E
DPC Series DPC200
________________________________________________________________________________________________
Inlet section
L.S. pressure relief valve
Type LSH Type LSD On BR section On BRF section

with lock arrangement with blind nut
C
A
W Z
Y Y
X X
J J
Type LSZ Type ST
B
with anti-tamper cap valve blanking plug
cap parts K
4COP116240
X J
D
J
X = wrench 13 / 42 Nm - 31 lbf
Y = wrench 10 / 9.8 Nm - 7.2 lbf BR section BRF section
W = allen wrench 3 Valve
A B C D
Z = wrench 10 / 9.8 Nm - 7.2 lbf type
J = wrench 7 / 24 Nm - 17.7 lbf mm in mm in mm in mm in
K = allen wrench 5 / 24 Nm - 17.7 lbf LSD 19.5 0.77 189.5 7.46 21.5 0.85 58 2.28
LSH 15 0.59 185 7.28 16 0.63 52.5 2.07
Pressure vs. flow diagram LSZ 32 1.26 202 7.95 34 1.34 70.5 2.78
0 20 40 60 (US gpm)
400 (psi)
(bar) max. setting (2)
5000
4000
Pressure
200 max. setting (1) min. and std. setting (2) 3000
2000
std. setting (1)
100
min. setting (1) 1000
0 0
0 40 80 120 160 200 240 280 (l/min)
Flow
D1WWED02E 49
DPC200 DPC Series
Working section parts ordering codes _____________________________________________________________
Valve setting (bar)

Flow on ports A\B (l/min) port A port B port A port B
DPC200 / C22 - 104 (200\200) - 8EZ3T LG 1 . U100U320 . S250S250 - ...... - 12VDC
1 2 3A 4 5 6 7 3
3B Lever position: see page 60
8
6
2 2
1 1 3
4
1 Working section body kit* page 52

With compensator
DESCRIPTION: Without valves arrangement
2 Spool page 54
TYPE: DPC200/C10-FS3-M CODE: 5EL6209210 Flow is referred to 7 bar (102 psi) stand-by (margin pressure)
DESCRIPTION: As previous, with ISO 6162-1 type 1 flange connect. TYPE CODE DESCRIPTION
TYPE: DPC200/C11 CODE: 5EL6201311 Double acting with A and B closed in neutral position
DESCRIPTION: Without valves arrangement, with LSA-LSB ports 105 3CU4510025 25 l/min (6.6 US gpm) flow
TYPE: DPC200/C11-FS3-M(BSP) CODE: 5EL6209211 101 3CU4510051 50 l/min (13.2 US gpm) flow
DESCRIPTION: As previous, fwith ISO 6162-1 type 1 flange connect. 106 3CU4510075 75 l/min (19.8 US gpm) flow
TYPE: DPC200/C22 CODE: 5EL6201322 102 3CU4510101 100 l/min (26.4 US gpm) flow
DESCRIPTION: Arranged for "U" size valves and L.S. relief valves, 107 3CU4510125 125 l/min (33 US gpm) flow
with LSA-LSB ports 103 3CU4510151 150 l/min (39.5 US gpm) flow
DESCRIPTION: As previous, with ISO 6162-1 type 1 flange connect. 104 3CU4510201 200 l/min (52.8 US gpm) flow
TYPE: DPC200/C32 CODE: 5EL6201332 Double acting with A and B to tank in neutral position
DESCRIPTION: Arranged for "UL" size valves and L.S.relief valves, 205 3CU4524025 25 l/min (6.6 US gpm) flow
with LSA-LSB ports 201 3CU4524050 50 l/min (13.2 US gpm) flow
TYPE: DPC200/F32 CODE: 5EL6204332 207 3CU4524125 125 l/min (33 US gpm) flow
DESCRIPTION: As Type C32, for floating circuit 203 3CU4524150 150 l/min (39.5 US gpm) flow
TYPE: DPC200/F32-FS3-M(BSP) CODE: 5EL6209232F 208 3CU4524175 175 l/min (46.2 US gpm) flow
Without compensator, with check valve Double acting with A and B partially to tank in neutral position
TYPE: DPC200/CV32 CODE: 5EL6201332A 2H05 3CU4525025 25 l/min (6.6 US gpm) flow
DESCRIPTION: Arranged for "UL" size valves and L.S. relief valves, 2H01 3CU4525050 50 l/min (13.2 US gpm) flow
with LSA-LSB ports 2H06 3CU4525075 75 l/min (19.8 US gpm) flow
TYPE: DPC200/CV32-FS3-M(BSP) CODE: 5EL6209232A 2H02 3CU4525100 100 l/min (26.4 US gpm) flow
DESCRIPTION: As previous, with ISO 6162-1 type 1 flange connect. 2H07 3CU4525125 125 l/min (33 US gpm) flow
TYPE: DPC200/FV32 CODE: 5EL6204332A 2H03 3CU4525150 150 l/min (39.5 US gpm) flow
DESCRIPTION: For floating circuit, arranged for "UL" size valves and 2H08 3CU4525175 175 l/min (46.2 US gpm) flow
L.S. relief valves, with LSA-LSB ports 2H04 3CU4525200 200 l/min (52.8 US gpm) flow
TYPE: DPC200/FV32-FS3-M(BSP) CODE: 5EL6209232FA
DESCRIPTION: As previous, with ISO 6162-1 type 11 flange connect. NOTE (*): Codes are referred to BSP thread.
50 D1WWED02E
DPC Series DPC200
______________________________________________________________
Working section parts ordering codes
2 Spool (continued) page 54 5 Port valves page 61

TYPE CODE DESCRIPTION TYPE CODE DESCRIPTION
Single acting on A, B plugged: needs G1 plug "U" size valves
305 3CU4530025 25 l/min (6.6 US gpm) flow UT XTAP522442 Valve blanking plug
301 3CU4530050 50 l/min (13.2 US gpm) flow C 5KIT410000 Anticavitation valve (for U cavity)
306 3CU4530075 75 l/min (19.8 US gpm) flow Fixed setting antishock and anticavitation valves: setting is referred
302 3CU4530100 100 l/min (26.4 US gpm) flow to 10 l/min (2.6 US gpm)
307 3CU4530125 125 l/min (33 US gpm) flow TYPE: U 100 CODE: 5KIT330 100
303 3CU4530150 150 l/min (39.5 US gpm) flow setting (bar) setting (bar)
308 3CU4530175 175 l/min (46.2 US gpm) flow SETTING:
304 3CU4530200 200 l/min (52.8 US gpm) flow 50 bar (725 psi) 63 bar (914 psi) 80 bar (1150 psi)
Double acting with A and B closed in neutral position, 4 100 bar (1450 psi) 110 bar (1590 psi) 125 bar (1800 psi)
positions, floating in 4th pos., spool in: needs working section 140 bar (2050 psi) 150 bar (2150 psi) 160 bar (2300 psi)
type F or FV, positioner and controls type 13 175 bar (2550 psi) 190 bar (2750 psi) 200 bar (2900 psi)
3A "A" side spool control kit page 56 "UL" size valves
ULT XTAP528520 Valve blanking plug
CL 5KIT409000 Anticavitation valve (for UL cavity)
Mechanical positioners
Fixed setting antishock and anticavitation valves with pressure relief
7FT 5V07200000 With friction and center position feeling
function: setting is referred to 5 l/min 1.3 US gpm)
8 5V08200000 3 position, spring return to neutral position
TYPE: UL 100 CODE: 5KIT340 100 L
13 5V13200000 For floating circuit (spool type 5), 4 pos.,
setting (bar) setting (bar)
detent in 4th position, with spring return to
SETTING:
neutral pos.
8IM 5V08200801 Range from 5.2 to 15.3 bar (75 to 222 psi)
13IM 5V13200800 For floating circuit (spool type 5), range
2.5 to 7 bar (75 to 222 psi), floating 11 bar
(160 psi)
3B Electrohydraulic controls page 58 380 bar (5500 psi)
8EZ3T-12VDC 5V08200721 With AMP connector 6 L.S. port relief valves page 62
8EZ3T-24VDC 5V08200741 With AMP conector
Standard setting is referred to 10 l/min - 2.6 US gpm flow.
8EZ34T-12VDC 5V08200722 With Deutsch connector
LSD XCAR126215 With blind nut, range 40-180 bar /
For floating circuit (spool type 5)
2600-5100 psi std. setting 180 bar / 2600 psi
LSH XCAR126216 With locked arrangement, range 40-180 bar
4 "B" side spool control kit page 60 2600-5100 psi, std. setting 180 bar / 2600 psi
TYPE CODE DESCRIPTION LSZ 5CAR126221 With anti-tamper cap, range 40-180 bar
LG 5LEV200802 Cast iron lever box / 580-2600 psi, std. setting 90 bar / 1300 psi
LGN 5LEV200801 Cast iron lever box, without lever 5CAR126219 As previous, range 180-350 bar /
L 5LEV200701 Aluminium lever box 2600-5100 psi, std. setting 180 bar / 2600 psi
ST 5KIT126210 Relief valve blanking plug
7 Section threading
Specify threading only if it is different from BSP standard. For section
with ISO 6162-1 type 1 flange connection digit: FS3-M(BSP), only
FS3-M for type C10
8 Plug for single acting spool*

CODE DESCRIPTION
3XTAP740210 G1 plug
4FL1066180 DN19 blind flange
D1WWED02E 51
DPC200 DPC Series
Working section __________________________________________________________________________________________
Without port valves
LS bottom ports position

lever side
0.47
(not for type C10)
12
lever side
LSA
1.61
6.69
170
41
LSB
135.75 71.25
85.5
3.37
5.34 2.81
0.177
4.5
FS3-M(BSP) optional connection

36.5
1.44 47.6
207 1.87
8.15 M10 23.8
nr. 4+4 threads 0.94 lever side
A B
2.09
22.2
0.87
53
26.5
1.04
26.5
1.04
11.1
0.44
64.75 68 74.25 68 74.25
2.549 2.68 2.923 2.68 2.923
With port valves

"U" and "UL" size valves have
the same position
L.S. valve
10°
on port A
L.S. valve
on port B
17.95 46.8 48.5 25.75

0.707 1.84 1.91 1.014
Port B valve
0.67
17
A B
0.59
15
0.37
9.5
Port A valve 41.3 20.5 12.45

11.5
0.45
1.63 0.81 0.490
52 D1WWED02E
DPC Series DPC200
___________________________________________________________________________________________
Working section
With compensator
Type C10 Type C11 Types C22 - C32 Type F32
B A B A B A B A
LSA LSB LSA LSB LSA LSB
Without compensator, with check valve
Type CV11 Types CV22 - CV32 Type FV32
B A B A B A
LSA LSB LSA LSB LSA LSB
D1WWED02E 53
DPC200 DPC Series
Working section __________________________________________________________________________________________
Spools
Spool type 1 Spool type 2 Spool type 2H

A, B closed in neutral position A, B open to tank in neutral pos. A, B partially to tank in neutral pos.
1 0 2 1 0 2 1 0 2
B A B A B A
T T T T T T
P P P
Spool type 3 Spool type 5

single acting on A floating in 4th position (pos.3)
1 0 2 3 1 0 2
B A B A
T T T T
P P
Spool stroke Spool stroke
position 1: - 8 mm (- 0.31 in) position 1: + 8 mm (1 0.31 in)
position 2: + 8 mm (+ 0.31 in) position 2: - 8 mm (+ 0.31 in)
position 3: + 13 mm (- 0.51 in)
54 D1WWED02E
DPC Series DPC200
___________________________________________________________________________________________
Working section
Spools
Following curves are detected with standard spools, connecting P⇒A⇒B⇒T and P⇒B⇒A⇒T ports without flow multiplication.
Customized spools with backpressure or flow multiplication may require different force, pressure and pilot current for
operation.
NOTE: for spools up to 120 l/min (31.7 US gpm), the effective flow on working ports may differ by 10% between the 1st an 10th
section.
Metering curves
Compensated working section - 3 positions spools
Qin = 260 l/min (68.7 US gpm)
With 8IM 222 200 150 100 75 0 75 100 150 200 222
(psi)
control kit
-0.3 -0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 0.3 (in)
250
(l/min) 60
H H (US gpm)
200
G G
45
F F
Port flow
150
E -2.2 mm 2.2 mm E
D -0.087 in 0.087 in D 30
100
C C
50
B B 15
A A
0 0
-8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 (mm)
position 1 Spool stroke position 2
Pilot pressure
(bar)
With 8IM
15.3 15.0 12.0 9.0 6.0 5.2 0 5.2 6.0 9.0 12.0 15.0 15.3
control kit
Current (mA@12VDC)
1300 1200 1000 800 650 0 650 800 1000 1200 1300
With 8EZ3T
control kit (mA@24VDC)
650 600 500 400 325 0 325 400 500 600 650
Non-compensated working section

Spool flow vs. Stand-by pressure
(margin pressure)
0 100 200 300 400 (psi)
250
102 H G F E
(l/min) 60
D (US gpm) Spool nominal flow @ 7 bar (102 psi)
200 stand-by (margin pressure)
50
C A = 25 l/min (6.6 US gpm)
Port flow
150 40 B = 50 l/min (13.2 US gpm)

C = 75 l/min (19.8 US gpm)
B 30
100 D = 100 l/min (26.4 US gpm)
20 E = 125 l/min (33 US gpm)
A
50 F = 150 l/min (39.5 US gpm)
10 G = 175 l/min (46.2 US gpm)
0 0 H = 200 l/min (52.8 US gpm)
0 5 10 15 20 25 30 (bar)
7 Pressure
D1WWED02E 55
DPC200 DPC Series
Working section __________________________________________________________________________________________
With friction and center position feeling: type 7FT
2 0 1
17.5
0.69
X
Z Y
85.5
3.37
113.5
4.47
Features
Friction load adjusting . . . . . . .: 20-150 N (4.5-34 lbf) X = wrench 24 - 42 Nm (31 lbf)
Friction load std. setting . . . . .: 100 N (22.5 lbf) Y = allen wrench 6
Center tap (more than load) . . .: 100 N (22.5 lbf) Z = wrench 13 - 24 Nm ( 17.7 lbf)
With spring return to neutral position: type 8
2 0 1
Force vs. Stroke diagram

0 -0.05 -0.1 -0.15 -0.2 -0.25 -0.3 (in)
(N) 0 0.05 0.1 0.15 0.2 0.25 0.3 (in)

150
32
122.7 N - 27.6 lbf (lbf)
125
24
100
Force
65.3 N
75 14.7 lbf 16
50
43.5 N
8
25 9.8 lbf
85.5
3.37
±2.2 mm
±0.087 in
0 0
0 1 2 3 4 5 6 7 8 pos.2 (mm)
0 -1 -2 -3 -4 -5 -6 -7 -8 pos.1 (mm)
16 Stroke
0.63
56 D1WWED02E
DPC Series DPC200
___________________________________________________________________________________________
Working section
With detent in 4th position (pos.3), for floating circuit: type 13

Need working section type F or FV and floating circuit spools type 5.
25.5
1.00 X
2 0 1 3
X
85.5
3.37
52
2.05
X = wrench 17 - 24 Nm (17.7 lbf)
31 G1/4 Type 8IM

1.22 VB VA
VA 2 0 1
1.06
27
VB
Type 13IM
For floating circuit
VB VA
85.5
3.37
0
85.5
2 1 3
3.37
26.5
Features (all types) 1.04
53
Max. pressure . . . . . . . . . . . . . : 50 bar (725 psi)
2.09
Type 8IM: suggested pressure

Type 8IM: Stroke vs. Pressure diagram control curve: type 020
-0.3 -0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 0.3 (in) 0 0.05 0.10 0.15 0.20 0.25 0.3 (in)
20 (psi) 40 (psi)
35 bar - 508 psi
(bar) 250 (bar)
15.3 bar - 222 psi 500
15 30
Pressure
Pilot pressure
200 400
10 150 20 300
0.30 in
spool 15.3 bar - 220 psi

5.2 bar - 75 psi dead band 100 200
7.6 mm -
5
7.25 mm
10 4.3 bar
50
0.29 in
63 psi 100
0.85 mm
0 0 0.033 in
0 0
-8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 (mm) 0 2 4 6 8 (mm)
position 1 Stroke position 2 Pusher stroke
D1WWED02E 57
DPC200 DPC Series
Working section __________________________________________________________________________________________
Electrohydraulic controls

Specifications Spool control type

8EZ3 13EZ3
12 VDC 4.72 Ω 4.72 Ω

Coil impedance
24 VDC 20.8 Ω 20.8 Ω
12 VDC 1.5 A 1.5 A

Max. operating current
24 VDC 0.75 A 0.75 A
No load current consumption 0 0
Hysteresis max. (1)

internal drain 5% with lever 7% with lever
from 0 ⇒ 100% of stroke < 150 ms < 250 ms

Time response
from 100% ⇒ 0 of stroke < 80 ms < 125 ms
12 VDC 650 mA 400 mA

Min. flow control signal
24 VDC 325 mA 200 mA
12 VDC 1300 mA 600 mA

Max. flow control signal
24 VDC 650 mA 300 mA
12 VDC - 850 mA
Float flow control signal
24 VDC - 250 mA
low frequency 150 Hz 150 Hz

Dither frequency
high frequency 150 Hz - 350 mA 150 Hz - 350 mA
Insertion 100% 100%
Coil insulance Class H (180°C - 356°F) Class H (180°C - 356°F)
Connector type AMP JPT - Deutsch DT AMP JPT - Deutsch DT
Weather protection (connector) IP65 (type JPT) - IP69K (type DT) IP65 (type JPT) - IP69K (type DT)
Max. back pressure 5 bar (72.5 psi) 5 bar (72.5 psi)
Note (1) for the calculation rules see "Appendix A" on page 71.
Listed electrohydraulic controls need CED100X or CED400X electronic unit; for information contact Sales Department.
58 D1WWED02E
DPC Series DPC200
___________________________________________________________________________________________
Working section
Electrohydraulic controls
Control Types
1 : With AMP JPT connector - mating connector AMP JPT, code: 5CON003
2 : With Deutsch DT04 connector - mating connector Deutsch DT06-2S code: 5CON140031
2
1
EVA EVB
Types
port A port B
8EZ3 - 8EZ34
EVA
7.64
194
7.13
181
EVB
2 0 1
85.5
3.37
Types
13EZ3 - 13EZ34
For floating circuit
EVA
EVB
2 0 1 3
A B
58
2.28
Types 8EZ3: Stroke vs. Current diagram

-0.3 -0.25 -0.2 -0.15 -0.1 -0.05 0 0.05 0.1 0.15 0.2 0.25 0.3 (in)
1600 800
(mA@12VDC) 1300 / 750 mA (mA@24VDC)
1200 600
spool
Current
dead band
800 400
650 / 325 mA
400 200
0 0
-8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 (mm)
D1WWED02E 59
DPC200 DPC Series
Working section __________________________________________________________________________________________
"B" side spool control kit
Cast iron standard lever box; type LG
2 0 1 3
Lever assembly position
3 See page 50 for specification
32 in working section description
°
11
58.5 8° 0 15° 0
45° 3 0'
2.30 30
°
1
18
°3
0'
30
°
2
Z
30°
85.5
3.37
3
2.40
X
61
2.09
°
53
30
Y
104
4.09
Y
B X = allen wrench 3
Y = wrench 10 / 9.8 Nm - 7.2 lbf
Z = allen wrench 4 / 6.6 Nm - 4.9 lbf
0.83
X
21
M8
Cast iron lever box, without lever; type LGN Aluminium lever box; type L
2 0 1 3 2 0 1 3
Dimensions and lever

Dimensions are the positions are the same
same of type LG of type LG
B B
wrench 8
60 D1WWED02E
DPC Series DPC200
___________________________________________________________________________________________
Working section
Port valves
Antishock anticavitation valves, type U Type U, setting example

Anticavitation valve, type C (10 l/min - 2.6 Us gpm)
Type U 0 3 6 9 12 15 (US gpm)
antishock valve 500
(psi)
(bar) 420 bar - 6100 psi
X 400 6000
max. 0.079
340 bar - 4950 psi

max. 2
Pressure
300 260 bar - 3750 psi 4500
210 bar - 3050 psi
200 3000
140 bar - 2050 psi
80 bar - 1150 psi
100 1500
Type C
6.69
170
anticavitation valve 25 bar - 360 psi

0
0
X 0 10 20 30 40 50 60 (l/min)
Flow
Types U-C, pressure drop

(in anticavitation)
0 3 6 9 12 15 (US gpm)
Type UT 20 (psi)
valve blanking plug (bar)
250
X 15
A B
0.67
17
200
Pressure
0.37
9.5
10 150
eC
Typ 100
17.95 46.8 48.5 25.75 X = wrench 13 5 U
ype 50
0.707 1.84 1.91 1.014 24 Nm - 17.7 lbf
T
0 0
0 10 20 30 40 50 60 (l/min)
Flow
Antishock anticavitation valves with

pressure relief function, type UL Type UL, setting example
Anticavitation valve, type CL (5 l/min - 1.3 Us gpm)
Type UL 0 10 20 30 40 (US gpm)
antishock valve 500
(psi)
(bar)
Y 400 380 bar / 5500 psi 6000
max. 0.43
max. 11
300 bar / 4350 psi

Pressure
300 4500
250 bar / 3600 psi
200 bar / 2900 psi
200 3000
150 bar / 2150 psi
100 bar / 1450 psi
100 1500
6.69
170
Type CL 50 bar / 725 psi

0 0
anticavitation valve 0 40 80 120 160 (l/min)
Y Flow
Types UL-CL, pressure drop

(in anticavitation)
0 10 20 30 40 (US gpm)
40 (psi)
(bar)
500
Type ULT 30
A B valve blanking plug L 400
U
Pressure
pe
Y Ty 300
20
CL
pe 200
Ty
valves position are the same of type U 10
100
0 0
Y = wrench 19 0 40 80 120 160 (l/min)
42 Nm - 31 lbf Flow
D1WWED02E 61
DPC200 DPC Series
Working section __________________________________________________________________________________________
L.S. port relief valves
Type LSH Type LSD Type LSZ

L.S. valve on port B
with lock arrangement with blind nut with anti-tamper cap
L.S. valve
W cap parts
on port A Z
Y Y 4COP116240
A
X X X
J J
J
Type ST X = wrench 13 / 42 Nm - 31 lbf

6.69
170
6.18
valve blanking plug
157
Y = wrench 10 / 9.8 Nm - 7.2 lbf

K W = allen wrench 3
Z = wrench 10 / 9.8 Nm - 7.2 lbf
J = wrench 7 / 24 Nm - 17.7 lbf
J K = allen wrench 5 / 24 Nm - 17.7 lbf
Pressure vs. flow diagram

0.59
15
0 20 40 60 (US gpm)
11.5
0.45
400 (psi)
(bar) max. setting (2)
5000
41.3 20.5 12.45 4000
Pressure
1.63 0.81 0.490

(1) (2) 3000
200 max. setting min. and std. setting
dim. A 2000
Valve type std. setting (1)
100
mm in 1000
min. setting (1)
LSD 20 0.79
0 0
LSH 15.5 0.61 0 40 80 120 160 200 240 (l/min)
LSZ 32.5 1.28 Flow
62 D1WWED02E
DPC Series DPC200
_________________________________________________________________
Outlet section parts ordering codes
DPC200 / RF 3 0 - ...... DPC200 / RD 3 1 - ......
1 2 3 4 1 2 3 4
2 2
3
1
1 Outlet section* page 64 3 Port options*

TYPE CODE DESCRIPTION TYPE: 0 DESCRIPTION: Without ports (only for RF type)
RF 3FIA720300 Without ports TYPE: 1 DESCRIPTION: Ports P1 and T1 plugged
RD 3FIA720302 With P1, T1 and LS1 ports PLUG CODE: 3XTAP740210 (G1) + XTAP450240 (G1-1/4)
RD-FS3-M(BSP) 3FIA720901 As previous, with ISO 6162-1 type 1 BLIND FLANGE CODE: 4FL1066180 (DN19) + 4FL1071190 (DN25)
flange connection TYPE: 2 DESCRIPTION: Port P1 plugged and T1 open
PLUG CODE: 3XTAP740210 (G1)
2 Drain options page 65 BLIND FLANGE CODE: 4FL1066180 (DN19)
TYPE: 3 DESCRIPTION: Port P1 open and T1 plugged
TYPE CODE DESCRIPTION PLUG CODE: XTAP450240 (G1-1/4)
1 XTAP517460 Internal drain; to use with mechanical BLIND FLANGE CODE: 4FL1071190 (DN25)
controls TYPE: 4 DESCRIPTION: Ports P and T open
2 XTAP217160 Internal drain; to use with hydraulic
controls
3 XCAR119611* External drain G1/4; for electrohydraulic
4 Section threading
controls Specify threading only if it is different from BSP standard.
For section with ISO 6162-1 type 1 flange connection digit: FS3-
M(BSP).
D1WWED02E 63
DPC200 DPC Series
Outlet section _____________________________________________________________________________________________
Type RD31 Type RF30

With ports P1, T1 (plugged) and LS1; external drain Without ports; external drain
L L
T1
171.5
6.75
6.34
161
4.29
109
P1
LS1
1.85
47
34.5
1.36
0.63
16
21.25 12 5.25
0.47
12
0.837 0.47 0.207

210.5
8.29
207
8.15
0.063
1.6
L Note: The port LS1 must not

be plugged (in case it’s not
49.5
1.95
2.20
56
used it has to be connected

26.9
1.06
to tank).
M12
11.5 25 134
0.45 0.98 5.28
FS3-M(BSP) optional connection Type RF31 Type RF30
47.6 52.4 T2
1.87 2.06
23.8 26.2 3/8-16 UNC
0.94 1.04 nr. 4+4 threads
P2 L
L
T1
26.2
1.03
13.1
0.52
4.29
109
P1
LS1
22.2
4.29
38.5
1.52
11.1
0.44
27.75 17.25
1.093 0.679 LS1
49.5
1.95
76.5
3.01
64 D1WWED02E
DPC Series DPC200
______________________________________________________________________________________________
Outlet section
Drain options
Option 1
internal drain for
L mechanical controls Option 1 Option 2 Option 3
allen wrench 5
24 Nm - 17.7 lbf
171.5 with option 3
6.75 with option 3
6.34
161
152.5
6.00
Option 2 L
internal drain for
hydraulic controls
allen wrench 6
24 Nm - 17.7 lbf
Option 3
external drain for
electrohydraulic controls
wrench 19
24 Nm - 17.7 lbf
D1WWED02E 65
Special configurations DPC Series
Connection between DPC Series valves ____________________________________________________________

DPC200 directional valve DPC130 directional valve
DPC200/1/BR2-10(D220\ELP)/C30-104(200\200)-8EZ3TLG1.UTUT/EIR/C10-1S8EZ3TL1/RF30/DPC130/1-......
Nr. of working Inlet section Working section 1 Working Outlet Nr. of working
sections section section sections
directional valves common specification
....BSP-12VDC-<SB20-CVN>
DPC200 inlet section
DPC200 working section
DPC130 working section
DPC130 outlet section
3
1
1 Intermediate section page 68 NOTE: the maximum number of working

TYPE CODE DESCRIPTION sections should not exceed 10 units
EIR 638403001 Section for assembling of DPC200 and
DPC130 in single directional valve; with LS
port
2 DPC200 side assembling kit 3 DPC130 side assembling kit

CODE CODE DESCRIPTION CODE DESCRIPTION
With inlet section type 5TIR108112 For 1 working section valve
Type BR Type BRF 5TIR108160 For 2 working sections valve
5TIR112180 5TIR112141 For 1 working section valve 5TIR108208 For 3 working sections valve
5TIR112235 5TIR112194 For 2 working sections valve 5TIR108256 For 4 working sections valve
5TIR112340 5TIR112300 For 4 working sections valve 5TIR108352 For 6 working section valve
5TIR112446 5TIR112407 For 6 working section valve 5TIR108448 For 8 working sections valve
66 D1WWED02E
DPC Series Special configurations
_____________________________________________________________
Connection between DPC Series valve
EVA1
EVA2 port A1
port A2
EVB2 EVB1
port B2 port B1
dim. E dim. F
1.30
sections
working
33
36.5
1.44
Nr. of
BR BRF
inlet section inlet section
A2 A1 P
L mm in mm in mm in
1 101.5 4.00 73.1 2.88 97 3.82
3.94
100
2 151.5 6.08 126.1 4.96 145 5.71

8.15
5.28
8.17 7.05 7.60
207
134
3 207.5 179.1 193
T
B2 4 260.5 10.26 232.1 9.14 241 9.49
5 313.5 12.34 285.1 11.22 289 11.38
6 366.5 14.43 338.1 13.31 337 13.27
B1 7 419.5 16.52 391.1 15.40 385 15.16
8 472.5 18.60 444.1 17.48 433 17.05
9 525.5 20.69 497.1 19.57 481 18.94
LS
LS2
F 45 E
1.77
B2 A2 B1 A1
P T
M
V2
L
V1
EVA2
EVB1
LS
EVB2 EVA1
LSAB LS2 LSA LSB
D1WWED02E 67
Accessories DPC Series
Coils and connectors ___________________________________________________________________________________
Connectors
Coil type Voltage Packard Packard
ISO4400 Deutsch DT AMP JPT
Weatherpack Metri-pack
4SLE001201(4)
4SLE001208(2-4)
12VDC 4SLE001200 4SLE001203 - -
4SLE001202(5)
4SLE001208(2-5)
4SLE002400 4SLE002401(4)
BER 24VDC 4SLE002403 - -
4SLE302400 (1) 4SLE002402(5)
48VDC 4SLE304800 (1) - - - -
110VDC 4SLE311000 (1) - - - -
220VDC 4SLE322000 (1)

- - - -
4SL3000128 (6)
12VDC 4SL3000120 4SL3000130 4SL3000122 4SL3000124 (6) 4SL3000127 (6)
4SL3000132 (3)
4SL3000240 4SL3000249
24VDC 4SL3000248 - -
4SL3030240 (1) 4SL3000247 (3)
BT 26VDC 4SL3000260 - - - -
4SL3000480
48VDC - - - -
4SL3030480 (1)
4SL3001100
110VDC - - - -
4SL3031100 (1)
220VDC 4SL3032200 (1) - - - -
Mating connectors
Standard 4CN1009995 5CON140031 5CON003 - -
12VDC - - - - -
24VDC 4CN3010240 - - - -
With rectifier 48VDC 4CN3010480 - - - -
110VDC 4CN3011100 - - - -
220VDC 4CN3012200 - - - -
Notes: (1) to use only with rectifier connector - (2) with bidirectional diode - (3) with unidirectional diode - (4) perpendicular connector - (5)
parallel connector - (6) with flying leads
68 D1WWED02E
DPC Series Accessories
_____________________________________________________________________________________
Coils and connectors
Type BER
ISO4400 connector DEUTSCH DT04 connector Features

(perpendicular type) Nominal voltage tolerance : ±10%
Power rating . . . . . . . . . . : 19.3 W - 12VDC
: 19.2 W - 24VDC
: 19.2 - 48VDC
2.68
59.5
2.34
68
: 19.2 - 110VDC
47.5
1.87
47.5
1.87
: 19.3 - 220VDC
23.5
23.5
0.93
0.93
Max. operating current . . : 1.61 A - 12VDC
38.5 36
: 0.80 A - 24VDC
38.5 36
1.52 1.42 1.52 1.42 : 0.40 A - 48VDC
: 0.17 A - 110VDC
DEUTSCH DT04 connector AMP JPT connector : 0.09 A - 220VDC
(parallel type) Coil insulance . . . . . . . . .: Class H
(180°C - 356°F)
Weather protection . . . . . : IP65 - ISO4400
: IP69K - Deutsch DT
68.3
2.69
: IP65 - AMP JPT

60.5
2.38
47.5
47.5
1.87
1.87
Insertion . . . . . . . . . . . . : 100%
23.5
23.5
0.93
0.93
38.5 36 38.5 36
1.52 1.42 1.52 1.42
Type BT Features
Nominal voltage tolerance : ±10%
ISO4400 connector AMP JPT connector Power rating . . . . . . . . . . : 21 W - 12 VDC
: 21 W - 24 VDC
: 21 W - 26 VDC
: 20.3 W - 48 VDC
: 15,7 W - 110 VDC
52.5
53.25
2.07
2.10
40.5
: 21.7 W - 220 VDC

1.59
40.5
1.59
18.25
18.25
Max. operating current . . : 1.77 A - 12 VDC

0.72
0.72
: 0.89 A - 24VDC
50 Ø 36.5 50 Ø 36.5 : 0.84 A - 26 VDC
1.97 1.44 1.97 1.44
: 0.43 A - 48 VDC
: 0.15 A - 110 VDC
DEUTSCH DT04 connector
DEUTSCH DT04 connector : 0.1 A - 220 VDC
(with unodorectional diode)
Coil insulance . . . . . . . . .: Class F
(155°C - 311°F)
Weather protection . . . . . : IP65 - ISO4400
61.75
: IP69K - Deutsch DT
61.25
2.43
2.41
: IP65 - AMP JPT

1.61
40.5
1.59
41
18.75
18.25
0.74
: IP67 - Weatherpack
0.72
: IP67 - Metri-pack
50 Ø 36.5 50 Ø 37,5 Insertion . . . . . . . . . . . . : 100%
1.97 1.44 1.97 1.48
DEUTSCH DT04 connector PACKARD METRI-PACK connector PACKARD WEATHER-PACK connector

(with cable) (with cable) (with cable)
170 145 215
6.69 5.71 8.46
40.5
40.5
40.5
1.59
1.59
1.59
18.25
18.25
18.25
0.72
0.72
0.72
50 Ø 36.5 50 Ø 36.5 50 Ø 36.5

1.97 1.44 1.97 1.44 1.97 1.44
D1WWED02E 69
Installation DPC Series
Installation and maintenance ________________________________________________________________________
The DPC Series valves are assembled and tested as per the technical specification of this catalogue.
Before the final installation on your equipment, follow the below re commendations:
- the valve can be assembled in any position; in order to prevent body deformation and spool sticking mount the product
on a flat surface;
- In order to prevent the possibility of water entering the spool control kit, do not use high pressure wash down directly on the
valve;
- prior to painting, ensure plugs on normally open ports are tightly in place.
B
A
B
A
T L
L
P
T
P
V1
V2
LS
LS V2 V1
FITTINGS TIGHTENING TORQUE - Nm / lbft

A and B LS signal port Hydraulic
THREAD TYPE P inlet port T outlet port L drain port
workports V pilot ports* control ports
BSP G 3/4 G 1/2 G 3/4 G 1/4 G 1/4 G 1/4
With O-Ring seal 90 / 66.4 50 / 36.9 90 / 66.4 25 / 18.4 25 / 18.4 25 / 18.4

With copper washer 90 / 66.4 60 / 44.3 90 / 66.4 30 / 22.1 30 / 22.1 30 / 22.1
DPC130
With steel and

70 / 51.6 60 / 44.3 70 / 51.6 16 / 11.8 16 / 11.8 16 / 11.8
rubber washer
1 1/16-12 7/8-14 1 1/16-12 9/16-18 9/16-18 9/16-18
UN-UNF
(SAE 12) (SAE 10) (SAE 12) (SAE 6) (SAE 6) (SAE 6)
With O-Ring seal 95 / 70 50 / 36.9 95 / 70 30 / 22.1 30 / 22.1 30 / 22.1
BSP G1 G1 G 1-1/4 G 1/4 G 1/4 G 1/4
With O-Ring seal 120 / 88.5 120 / 88.5 190 / 140 25 / 18.4 25 / 18.4 25 / 18.4
With copper washer 120 / 88.5 120 / 88.5 190 / 140 30 / 22.1 30 / 22.1 30 / 22.1
With steel and
120 / 88.5 120 / 88.5 190 / 140 16 / 11.8 16 / 11.8 16 / 11.8
rubber washer
DPC200
1 5/16-12 1 5/16-12 1 5/8-12 9/16-18 9/16-18 7/16-20

UN-UNF
(SAE 16) (SAE 16) (SAE 20) (SAE 6) (SAE 6) (SAE 4)
With O-Ring seal 150 / 111 150 / 111 200 / 147 30 / 22.1 30 / 22.1 18 / 13.3
SAE J518 code 61 3/4 [3/8-16 UNC] 3/4 [3/8-16 UNC] 1 [3/8-16 UNC]
ISO 6162-1 type 1 DN 19 [M10] DN 19 [M10] DN 25 [M10] - - -
[bolts threading]
28-40 / 20.7-29.5 28-40 / 20.7-29.5 37-48 / 27.3-35.4 - - -
(*) V2 port is M14x1.5 threading: tightenìng torque value is the same of G1/4 thread
NOTE – These torque are recommended. Assembly tightening torque depends on many factors, including lubrication, coating
and surface finish.
70 D1WWED02E
DPC Series Appendicies
_________________________________________________________________________________________________
Appendix A
Electrohydraulic controls: hysteresis calculation rule

Hysteresis is calculated as difference between control currents (I2-I1), needed to reach 50% of nominal spool stroke, referred
to maximum control current IMAX, needed to reach 100% of spool stroke.
I2 is determined on spool stroke increase line, I1 is determined on spool stroke decrease line.
Example diagram for

data detection
Max stroke
Stroke
I2 - I1
Hysteresis % = x 100
50% of max stroke IMAX
0
0 I1 I2 IMAX
Current
D1WWED02E 71
1st edition July 2012 WWW.WALVOIL.COM
D1WWED02E

Dpc130+Dpc200 Eng

Uploaded by

Copyright:

Available Formats

Dpc130+Dpc200 Eng

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Dpc130+Dpc200 Eng

Uploaded by

Copyright:

Available Formats

DPC

WALVOIL IS NOT RESPONSIBLE FOR ANY DAMAGE CAUSED BY AN

Advantages and options

For special options contact Sales Dept.

Working conditions _____________________________________________________________________________________

CAVITY ISO 1179 11926

Istallation and maintenace . . . . . . . . . . . . . . page 70

Dimensional data and performance ________________________________________________________________

P⇒T Pressure drop inlet compensator

DPC130/1 184 7.24 200 7.87 12.4 27.3

DPC130/5 376 14.80 392 15.43 36.5 80.5 0 0

Open center configuration example

Closed center configuration example

Complete sections ordering codes __________________________________________________________________

Nr. of working sections The valve is supplied painted,

1 Inlet section * page 12

Inlet section parts ordering codes _________________________________________________________________

Valve setting (bar)

DPC130 / BRF21 - S250 - BSP

1 Inlet section kit* page 14 4 Shut-Off pilot solenoid valve page 16

2 L.S. relief valves page 19 8 Circuit conversion kit

3 Solenoid operated unloading valve page 19

Inlet section _______________________________________________________________________________________________

Dimensions and hydraulic circuit

controls feeding (Pmax = 315 bar / 4600 psi) (P⇒IN)

BN11 type BN21 type

Dimensions and hydraulic circuit

V2 = M14x1.5 pilot pressure port for:

- electrohydraulic controls optional feeding (Pmax = 315 bar /

1.44 1.71 0.43

BR11 type BR21 type Pressure reducing valve diagram

Inlet section _______________________________________________________________________________________________

Dimensions and hydraulic circuit

Example of BRSO21 section

M = G1/4 pressure gauge connection P

Features Valve Dim. A

Dimensions and hydraulic circuit

Example of BRS section

needs G1/4 joint, code 5GIU519611

BRSO11 type BRSO21 type

Inlet section _______________________________________________________________________________________________

Dimensions and hydraulic circuit

Example of BRS section

Pressure reducing valve

Pressure reducing valve Pressure reducing valve diagram

L.S. pressure relief valve

Type LSH Type LSD

X = wrench 13 / 42 Nm - 31 lbf Dim. B

Solenoid operated unloading valve

Working and outlet section parts ordering codes _______________________________________________

3B Lever position: see page 36 5

1 Working section kit* page 22

8 Plug for single acting spool*

Working section __________________________________________________________________________________________

Dimensions and hydraulic circuit

Type C10 Type C13

1.30 1.63 lever side

Type C10 Type C13 Type C22

LSAB LSAB LSAB

Dimensions and hydraulic circuit