Test Zte

FCC RF Test Report Report No.
: FG1D0702
FCC RF Test Report

APPLICANT : ZTE CORPORATION
EQUIPMENT : LTE/WCDMA/GSM(GPRS) Multi-Mode Digital
Mobile Phone
BRAND NAME : ZTE
MODEL NAME : Z3353CA
FCC ID : SRQ-Z3353CA
STANDARD : 47 CFR Part 2, 24(E), 27(L)
CLASSIFICATION : PCS Licensed Transmitter Held to Ear (PCE)
TEST DATE(S) : Dec. 30, 2021 ~ Jan. 10, 2022
We, Sporton International Inc. (Kunshan), would like to declare that the tested sample has
been evaluated in accordance with the procedures given in ANSI C63.26-2015 and shown
compliance with the applicable technical standards.
The test results in this report apply exclusively to the tested model / sample. Without written
approval of Sporton International Inc. (Kunshan), the test report shall not be reproduced
except in full.
Reviewed by: Jason Jia / Supervisor
Approved by: Alex Wang / Manager
Sporton International Inc. (Kunshan)

No. 1098, Pengxi North Road, Kunshan Economic Development Zone Jiangsu Province 215300
People’s Republic of China
Sporton International Inc. (Kunshan) Page Number : 1 of 24

TEL : +86-512-57900158 Report Issued Date : Jan. 25, 2022
FAX : +86-512-57900958 Report Version : Rev. 01
FCC ID : SRQ-Z3353CA Report Template No.: BU5-FGLTE Version 2.0
FCC RF Test Report Report No. : FG1D0702
TABLE OF CONTENTS
REVISION HISTORY.......................................................................................................................................... 3
SUMMARY OF TEST RESULT ......................................................................................................................... 4
1 GENERAL DESCRIPTION .......................................................................................................................... 6
1.1 Applicant ............................................................................................................................................ 6
1.2 Manufacturer ...................................................................................................................................... 6
1.3 Product Feature of Equipment Under Test ........................................................................................ 6
1.4 Product Specification of Equipment Under Test ................................................................................ 6
1.5 Modification of EUT ........................................................................................................................... 7
1.6 Maximum ERP/EIRP Power and Emission Designator ..................................................................... 7
1.7 Testing Location ................................................................................................................................ 8
1.8 Test Software ..................................................................................................................................... 8
1.9 Applicable Standards ......................................................................................................................... 8
2 TEST CONFIGURATION OF EQUIPMENT UNDER TEST ........................................................................ 9
2.1 Test Mode .......................................................................................................................................... 9
2.2 Connection Diagram of Test System ............................................................................................... 10
2.3 Support Unit used in test configuration and system ........................................................................ 10
2.4 Measurement Results Explanation Example ................................................................................... 10
2.5 Frequency List of Low/Middle/High Channels ................................................................................. 11
3 CONDUCTED TEST ITEMS ...................................................................................................................... 12
3.1 Measuring Instruments .................................................................................................................... 12
3.2 Test Setup ....................................................................................................................................... 12
3.3 Test Result of Conducted Test ........................................................................................................ 12
3.4 Conducted Output Power and ERP/EIRP ....................................................................................... 13
3.5 Peak-to-Average Ratio .................................................................................................................... 14
3.6 Occupied Bandwidth ........................................................................................................................ 15
3.7 Conducted Band Edge .................................................................................................................... 16
3.8 Conducted Spurious Emission ........................................................................................................ 18
3.9 Frequency Stability .......................................................................................................................... 19
4 RADIATED TEST ITEMS .......................................................................................................................... 20
4.1 Measuring Instruments .................................................................................................................... 20
4.2 Test Setup ....................................................................................................................................... 20
4.3 Test Result of Radiated Test ........................................................................................................... 21
4.4 Radiated Spurious Emission ........................................................................................................... 22
5 LIST OF MEASURING EQUIPMENT ........................................................................................................ 23
6 UNCERTAINTY OF EVALUATION ........................................................................................................... 24
APPENDIX A. TEST RESULTS OF CONDUCTED TEST
APPENDIX B. TEST RESULTS OF RADIATED TEST
APPENDIX C. TEST SETUP PHOTOGRAPHS

REVISION HISTORY
REPORT NO. VERSION DESCRIPTION ISSUED DATE
FG1D0702 Rev. 01 Initial issue of report Jan. 25, 2022

SUMMARY OF TEST RESULT
Report
FCC Rule Description Limit Result Remark
Section
§2.1046 Conducted Output Power - Report Only -
Equivalent Isotropic Radiated Power

§24.232(c) EIRP < 2Watt -
3.4 (Band 2)
PASS
Equivalent Isotropic Radiated Power
§27.50(d)(4) EIRP < 1Watt -
(Band 4)
3.5 §24.232(d) Peak-to-Average Ratio <13 dB PASS -
3.6 §2.1049 Occupied Bandwidth - Report Only -
§2.1051
Conducted Band Edge Measurement
3.7 §24.238(a) < 43+10log10(P[Watts]) PASS -
(Band 2) (Band 4)
§§27.53(h)
§2.1051
Conducted Spurious Emission
3.8 §24.238(a) < 43+10log10(P[Watts]) PASS -
(Band 2) (Band 4)
§27.53(h)
§2.1055
< 2.5 ppm for Part 22
§22.355
Frequency Stability
3.9 §2.1055 PASS -
Temperature & Voltage
§24.235 Within Authorized Band
§27.54

Report
FCC Rule Description Limit Result Remark
Section
Under limit
§2.1053
Radiated Spurious Emission 32.72 dB at
4.4 §24.238(a) < 43+10log10(P[Watts]) PASS
(Band 2) (Band 4) 5550.000
§27.53(h)
MHz
Declaration of Conformity:
The test results with all measurement uncertainty excluded are presented in accordance with the regulation
limits or requirements declared by manufacturers.
Comments and Explanations:
The declared of product specification for EUT presented in the report are provided by the manufacturer, and the
manufacturer takes all the responsibilities for the accuracy of product specification.

1 General Description
1.1 Applicant
ZTE CORPORATION
ZTE Plaza, Keji Road South, Hi-Tech, Industrial Park, Nanshan District, Shenzhen, Guangdong,
518057, P.R.China
1.2 Manufacturer
ZTE CORPORATION
ZTE Plaza, Keji Road South, Hi-Tech, Industrial Park, Nanshan District, Shenzhen, Guangdong,
518057, P.R.China
1.3 Product Feature of Equipment Under Test

Product Feature
Equipment LTE/WCDMA/GSM(GPRS) Multi-Mode Digital Mobile Phone
Brand Name ZTE
Model Name Z3353CA
FCC ID SRQ-Z3353CA
Conducted: 862829060000600
IMEI Code
Radiation: 004402543180974
HW Version Z3353CAHW1.0
SW Version Z3353CAV1.0.0B01
EUT Stage Production Unit
Remark: This is a C2PC report for Z3353CA, based on change FCC ID report (original FCC ID:
SRQ-Z3352CA, change FCC ID: SRQ-Z3353CA). The difference refer to the
Z3353CA_Class II Permissive Change letter exhibit separately. According tothe differences, only
the related test cases were verified from original report which can be referredto Sporton Report
Number FG010610B(original FCC ID: SRQ-Z3352CA).
1.4 Product Specification of Equipment Under Test

Standards-related Product Specification
LTE Band 2 : 1850 MHz ~ 1910 MHz
Tx Frequency
Rx Frequency
LTE Band 2 : 1.4MHz / 3MHz / 5MHz / 10MHz / 15MHz / 20MHz
Bandwidth
LTE Band 4 : 1.4MHz / 3MHz / 5MHz / 10MHz / 15MHz / 20MHz
Maximum Output Power to LTE Band 2 : 22.70 dBm
Antenna LTE Band 4 : 22.75 dBm
LTE Band 2 : -0.67 dBi
Antenna Gain
LTE Band 4 : -0.50 dBi

Type of Modulation QPSK / 16QAM / 64QAM
1.5 Modification of EUT

No modifications are made to the EUT during all test items.
1.6 Maximum ERP/EIRP Power and Emission Designator

LTE Band 2 QPSK 16QAM/64QAM
Frequency
BW Maximum Maximum
Range
(MHz) EIRP(W) EIRP(W)
(MHz)
1.4 1850.7 ~ 1909.3 0.1592 0.1371
3 1851.5 ~ 1908.5 0.1535 0.1309
5 1852.5 ~ 1907.5 0.1581 0.1358
10 1855.0 ~ 1905.0 0.1574 0.1343
15 1857.5 ~ 1902.5 0.1592 0.1349
20 1860.0 ~ 1900.0 0.1596 0.1352
LTE Band 4 QPSK 16QAM/64QAM
Frequency
BW Maximum Maximum
Range
(MHz) EIRP(W) EIRP(W)
(MHz)
1.4 1710.7 ~ 1754.3 0.1667 0.1400
3 1711.5 ~ 1753.5 0.1614 0.1343
5 1712.5 ~ 1752.5 0.1629 0.1510
10 1715.0 ~ 1750.0 0.1626 0.1355
15 1717.5 ~ 1747.5 0.1667 0.1403
20 1720.0 ~ 1745.0 0.1679 0.1365

1.7 Testing Location

<FCC>-KS
Sporton International Inc. (Kunshan) is accredited to ISO/IEC 17025:2017 by American Association for
Laboratory Accreditation with Certificate Number 5145.02.
Test Firm Sporton International Inc. (Kunshan)
No. 1098, Pengxi North Road, Kunshan Economic Development Zone
Jiangsu Province 215300 People’s Republic of China

Test Site Location
TEL : +86-512-57900158
FAX : +86-512-57900958
FCC Test Firm

Sporton Site No. FCC Designation No.
Test Site No. Registration No.
03CH04-KS
CN1257 314309
TH01-KS
1.8 Test Software

Item Site Manufacture Name Version
1. 03CH04-KS AUDIX E3 6.2009-8-24a
1.9 Applicable Standards

According to the specifications of the manufacturer, the EUT must comply with the requirements of the
following standards:
 47 CFR Part 2, 24(E), 27(L)
 ANSI C63.26-2015
 FCC KDB 971168 D01 Power Meas License Digital Systems v03r01
 FCC KDB 412172 D01 Determining ERP and EIRP v01r01
Remark:
1. All test items were verified and recorded according to the standards and without any deviation
during the test.
2. This EUT has also been tested and complied with the requirements of FCC Part 15, Subpart B,
recorded in a separate test report.

2 Test Configuration of Equipment Under Test

2.1 Test Mode
Antenna port conducted and radiated test items listed below are performed according to KDB 971168
D01 Power Meas License Digital Systems v03r01 with maximum output power.
Radiated measurements are performed by rotating the EUT in three different orthogonal test planes to
find the maximum emission.
Bandwidth (MHz) Modulation RB # Test Channel
Test Items Band
1.4 3 5 10 15 20 QPSK 16QAM 64QAM 1 Half Full L M H
Max. 2 v v v v v v v v v v v v v v v
Output
Power 4 v v v v v v v v v v v v v v v
Conducted 2 v v v v v v v v v v v v v
Band Edge 4 v v v v v v v v v v v v v
Conducted 2 v v v v v v v v v v v v v
Spurious
Emission 4 v v v v v v v v v v v v v
Frequency 2 v v v v
Stability 4 v v v v
E.R.P / 2 v v v v v v v v v v v v v
E.I.R.P 4 v v v v v v v v v v v v v
Radiated 2 Worst Case v

Spurious
Emission 4 Worst Case v
1. The mark “v “ means that this configuration is chosen for testing
2. The mark “-“ means that this bandwidth is not supported.
Note 3. The device is investigated from 30MHz to 10 times of fundamental signal for radiated spurious emission test under
different RB size/offset and modulations in exploratory test. Subsequently, only the worst case emissions are
reported.

2.2 Connection Diagram of Test System
System
AP router Notebook GPS Station BT Earphone
Simulator
Power
EUT Notebook
Source
Cradle Earphone iPod WLAN AP Monitor
This example is connection diagram of EUT test configurations.
. For detail, please refer to test mode configuration and setup photographs for each test item.
2.3 Support Unit used in test configuration and system

Item Equipment Trade Name Model No. FCC ID Data Cable Power Cord
1. Power Supply GWINSTEK PSS-2002 N/A N/A Unshielded, 1.8 m
2. LTE Base Station Anritsu MT8820C N/A N/A Unshielded, 1.8 m
2.4 Measurement Results Explanation Example

For all conducted test items:
The offset level is set in the spectrum analyzer to compensate the RF cable loss between EUT
conducted output port and spectrum analyzer. With the offset compensation, the spectrum analyzer
reading level is exactly the EUT RF output level.
The spectrum analyzer offset is derived from RF cable loss.

Offset = RF cable loss.
Following shows an offset computation example with cable loss 5.40 dB.
Example :
Offset(dB) = RF cable loss(dB)
= 5.40 (dB)

2.5 Frequency List of Low/Middle/High Channels

LTE Band 2 Channel and Frequency List
BW [MHz] Channel/Frequency(MHz) Lowest Middle Highest
Channel 18700 18900 19100
20
Frequency 1860 1880 1900
Channel 18675 18900 19125
15
Frequency 1857.5 1880 1902.5
Channel 18650 18900 19150
10
Frequency 1855 1880 1905
Channel 18625 18900 19175
5
Frequency 1852.5 1880 1907.5
Channel 18615 18900 19185
3
Frequency 1851.5 1880 1908.5
Channel 18607 18900 19193
1.4
Frequency 1850.7 1880 1909.3
LTE Band 4 Channel and Frequency List

BW [MHz] Channel/Frequency(MHz) Lowest Middle Highest
Channel 20050 20175 20300
20
Frequency 1720 1732.5 1745
Channel 20025 20175 20325
15
Frequency 1717.5 1732.5 1747.5
Channel 20000 20175 20350
10
Frequency 1715 1732.5 1750
Channel 19975 20175 20375
5
Frequency 1712.5 1732.5 1752.5
Channel 19965 20175 20385
3
Frequency 1711.5 1732.5 1753.5
Channel 19957 20175 20393
1.4
Frequency 1710.7 1732.5 1754.3

3 Conducted Test Items

3.1 Measuring Instruments
See list of measuring instruments of this test report.
3.2 Test Setup

3.2.1 Conducted Output Power
3.2.2 Peak-to-Average Ratio, Occupied Bandwidth ,Conducted Band-Edge and

3.2.3 Frequency Stability
3.3 Test Result of Conducted Test

Please refer to Appendix A.

3.4 Conducted Output Power and ERP/EIRP

3.4.1 Description of the Conducted Output Power Measurement and ERP/EIRP
Measurement
A system simulator was used to establish communication with the EUT. Its parameters were set to
force the EUT transmitting at maximum output power. The measured power in the radio frequency on
the transmitter output terminals shall be reported.
The EIRP of mobile transmitters must not exceed 2 Watts for LTE Band 2.
The EIRP of mobile transmitters must not exceed 1 Watts for LTE Band 4.
According to KDB 412172 D01 Power Approach,
EIRP = PT + GT – LC, ERP = EIRP -2.15, where
PT = transmitter output power in dBm
GT = gain of the transmitting antenna in dBi
LC = signal attenuation in the connecting cable between the transmitter and antenna in dB
3.4.2 Test Procedures

1. The testing follows ANSI C63.26 Section 5.2
2. The transmitter output port was connected to the system simulator.
3. Set EUT at maximum power through the system simulator.
4. Select lowest, middle, and highest channels for each band and different modulation.
5. Measure and record the power level from the system simulator.

3.5 Peak-to-Average Ratio

3.5.1 Description of the PAR Measurement
Power Complementary Cumulative Distribution Function (CCDF) curves provide a means for
characterizing the power peaks of a digitally modulated signal on a statistical basis. A CCDF curve
depicts the probability of the peak signal amplitude exceeding the average power level. Most
contemporary measurement instrumentation include the capability to produce CCDF curves for an
input signal provided that the instrument’s resolution bandwidth can be set wide enough to
accommodate the entire input signal bandwidth. In measuring transmissions in this band using an
average power technique, the peak-to-average ratio (PAR) of the transmission may not exceed 13
dB.

1. The testing follows ANSI C63.26 Section 5.2.3.4 (CCDF).
2. The EUT was connected to spectrum and system simulator via a power divider.
3. Set the CCDF (Complementary Cumulative Distribution Function) option in spectrum analyzer.
4. The highest RF powers were measured and recorded the maximum PAPR level associated with
a probability of 0.1 %.
5. Record the deviation as Peak to Average Ratio.

3.6 Occupied Bandwidth

3.6.1 Description of Occupied Bandwidth Measurement
The occupied bandwidth is the width of a frequency band such that, below the lower and above the
upper frequency limits, the mean powers emitted are each equal to a specified percentage 0.5% of
the total mean transmitted power.
The 26 dB emission bandwidth is defined as the frequency range between two points, one above and
one below the carrier frequency, at which the spectral density of the emission is attenuated 26 dB
below the maximum in-band spectral density of the modulated signal. Spectral density (power per unit
bandwidth) is to be measured with a detector of resolution bandwidth equal to approximately 1.0% of
the emission bandwidth.

2. The EUT was connected to spectrum analyzer and system simulator via a power divider.
3. The spectrum analyzer center frequency is set to the nominal EUT channel center frequency.
The span range for the spectrum analyzer shall be between two and five times the anticipated
OBW.
4. The nominal resolution bandwidth (RBW) shall be in the range of 1 to 5 % of the anticipated
OBW, and the VBW shall be at least 3 times the RBW.
5. Set the detection mode to peak, and the trace mode to max hold.
6. Determine the reference value: Set the EUT to transmit a modulated signal. Allow the trace to
stabilize. Set the spectrum analyzer marker to the highest level of the displayed trace.
(this is the reference value)
7. Determine the “-26 dB down amplitude” as equal to (Reference Value – X).
8. Place two markers, one at the lowest and the other at the highest frequency of the envelope of
the spectral display such that each marker is at or slightly below the “–X dB down amplitude”
determined in step 6. If a marker is below this “-X dB down amplitude” value it shall be placed
as close as possible to this value. The OBW is the positive frequency difference between the
two markers.
9. Use the 99 % power bandwidth function of the spectrum analyzer and report the measured
bandwidth.

3.7 Conducted Band Edge

3.7.1 Description of Conducted Band Edge Measurement
24.238 (a)
For operations in the 1850-1910 and 1930-1990 MHz band, the FCC limit is 43 + 10log10(P[Watts]) dB
below the transmitter power P(Watts) in a 1MHz bandwidth. However, in the 1 MHz bands
immediately outside and adjacent to the frequency block a resolution bandwidth of at least one
percent of the emission bandwidth of the fundamental emission of the transmitter may be employed.
27.53 (h)
For operations in the 1710 – 1755 MHz band, the FCC limit is 43 + 10log10(P[Watts]) dB below the
transmitter power P(Watts) in a 1 MHz bandwidth. However, in the 1MHz bands immediately outside
and adjacent to the licensee's frequency block, a resolution bandwidth of at least one percent of the
emission bandwidth of the fundamental emission of the transmitter may be employed.


1. The testing follows ANSI C63.26 section 5.7
3. The band edges of low and high channels for the highest RF powers were measured.
4. Set RBW >= 1% EBW in the 1MHz band immediately outside and adjacent to the band edge.
5. Beyond the 1 MHz band from the band edge, RBW=1MHz was used or a narrower RBW was
used and the measured power was integrated over the full required measurement bandwidth of
1 MHz.
6. Set spectrum analyzer with RMS detector.
7. The RF fundamental frequency should be excluded against the limit line in the operating
frequency band.
8. Checked that all the results comply with the emission limit line.
Example:
The limit line is derived from 43 + 10log(P)dB below the transmitter power P(Watts)
= P(W)- [43 + 10log(P)] (dB)
= [30 + 10log(P)] (dBm) - [43 + 10log(P)] (dB) = -13dBm.
9. When using the integration method, the starting frequency of the integration shall be centered
at one-half of the RBW away from the band edge.

3.8 Conducted Spurious Emission

3.8.1 Description of Conducted Spurious Emission Measurement
The power of any emission outside of the authorized operating frequency ranges must be lower than
the transmitter power (P) by a factor of at least 43 + 10 log (P) dB.
It is measured by means of a calibrated spectrum analyzer and scanned from 30 MHz up to a
th
frequency including its 10 harmonic.

1. The testing follows ANSI C63.26 section 5.7
3. The RF output of EUT was connected to the spectrum analyzer by RF cable and attenuator.
The path loss was compensated to the results for each measurement.
4. The middle channel for the highest RF power within the transmitting frequency was measured.
5. The conducted spurious emission for the whole frequency range was taken.
6. Make the measurement with the spectrum analyzer's RBW = 1MHz, VBW = 3MHz.
7. Set spectrum analyzer with RMS detector.
8. Taking the record of maximum spurious emission.
frequency band.
10. The limit line is derived from 43 + 10log(P)dB below the transmitter power P(Watts)
= P(W)- [43 + 10log(P)] (dB)
= [30 + 10log(P)] (dBm) - [43 + 10log(P)] (dB)
= -13dBm.

3.9 Frequency Stability

3.9.1 Description of Frequency Stability Measurement
The frequency stability shall be measured by variation of ambient temperature and variation of
primary supply voltage to ensure that the fundamental emission stays within the authorized frequency
block. The frequency stability of the transmitter shall be maintained within ±0.00025% (±2.5ppm) of
the center frequency.
3.9.2 Test Procedures for Temperature Variation

1. The testing follows ANSI C63.26 section 5.6.4
2. The EUT was set up in the thermal chamber and connected with the system simulator.
3. With power OFF, the temperature was decreased to -30°C and the EUT was stabilized before
testing. Power was applied and the maximum change in frequency was recorded within one
minute.
4. With power OFF, the temperature was raised in 10°C step up to 50°C. The EUT was stabilized
at each step for at least half an hour. Power was applied and the maximum frequency change
was recorded within one minute.
3.9.3 Test Procedures for Voltage Variation

1. The testing follows ANSI C63.26 section 5.6.5
2. The EUT was placed in a temperature chamber at 20±5°C and connected with the system
simulator.
3. The power supply voltage to the EUT was varied from 85% to 115% of the nominal value for
other than hand carried battery equipment.
4. For hand carried, battery powered equipment, reduce the primary ac or dc supply voltage to the
battery operating end point, which shall be specified by the manufacturer.
5. The variation in frequency was measured for the worst case.

4 Radiated Test Items

4.1 Measuring Instruments
See list of measuring instruments of this test report.
4.2 Test Setup

4.2.1 For radiated test below 30MHz
4.2.2 For radiated test from 30MHz to 1GHz

4.2.3 For radiated test above 1GHz
4.3 Test Result of Radiated Test

The low frequency, which started from 9 kHz to 30MHz, was pre-scanned and the result which was
20dB lower than the limit line was not reported.
Please refer to Appendix B.

4.4 Radiated Spurious Emission

4.4.1 Description of Radiated Spurious Emission
The radiated spurious emission was measured by substitution method according to ANSI C63.26.
The power of any emission outside of the authorized operating frequency ranges must be attenuated
below the transmitter power (P) by a factor of at least 43 + 10 log (P) dB.
The spectrum is scanned from 30 MHz up to a frequency including its 10th harmonic.

2. The EUT was placed on a turntable with 0.8 meter height for frequency below 1GHz and 1.5
meter height for frequency above 1GHz respectively above ground.
3. The EUT was set 3 meters from the receiving antenna mounted on the antenna tower.
4. The table was rotated 360 degrees to determine the position of the highest spurious emission.
5. The height of the receiving antenna is varied between 1m to 4m to search the maximum
spurious emission for both horizontal and vertical polarizations.
6. During the measurement, the system simulator parameters were set to force the EUT
transmitting at maximum output power.
7. Make the measurement with the spectrum analyzer's RBW = 1MHz, VBW = 3MHz, taking the
record of maximum spurious emission.
8. A horn antenna was substituted in place of the EUT and was driven by a signal generator.
9. Tune the output power of signal generator to the same emission level with EUT maximum
spurious emission.
10. EIRP (dBm) = S.G. Power – Tx Cable Loss + Tx Antenna Gain
11. ERP (dBm) = EIRP - 2.15
frequency band.
The limit line is derived from 43 + 10log(P)dB below the transmitter power P(Watts)
= P(W)- [43 + 10log(P)] (dB)
= [30 + 10log(P)] (dBm) - [43 + 10log(P)] (dB)
= -13dBm.

5 List of Measuring Equipment

Calibration
Instrument Manufacturer Model No. Serial No. Characteristics Test Date Due Date Remark
Date
Spectrum Dec. 30, 2021~ Conducted
R&S FSV40 101040 10Hz~40GHz Oct. 14, 2021 Oct. 13, 2022
Analyzer Dec. 31, 2021 (TH01-KS)
Dec. 30, 2021~ Conducted
Power divider STI STI08-0055 - 0.5~40GHz Aug. 26, 2021 Aug. 25, 2022
Dec. 31, 2021 (TH01-KS)
Temperature &
-40~+150°C Dec. 30, 2021~ Conducted
humidity Hongzhan LP-150U H2014011440 Jul. 12, 2021 Jul. 11, 2022
20%~95%RH Dec. 31, 2021 (TH01-KS)
chamber
EXA Spectrum 10Hz-44G,MAX Radiation
Keysight N9010A MY55150244 Apr. 13, 2021 Jan. 10, 2022 Apr. 12, 2022
Analyzer 30dB (03CH04-KS)
Radiation
Loop Antenna R&S HFH2-Z2 100321 9kHz~30MHz Oct. 30, 2021 Jan. 10, 2022 Oct. 29, 2022 (03CH04-KS)
Radiation
Bilog Antenna TeseQ CBL6111D 49922 30MHz-1GHz May 30, 2021 Jan. 10, 2022 May 29, 2022
(03CH04-KS)
Radiation
Horn Antenna Schwarzbeck BBHA9120D 1356 1GHz~18GHz Apr. 18, 2021 Jan. 10, 2022 Apr. 17, 2022
(03CH04-KS)
Radiation
SHF-EHF Horn Com-power AH-840 101070 18GHz~40GHz Jan. 05, 2022 Jan. 10, 2022 Jan. 04, 2023
(03CH04-KS)
Radiation
Amplifier SONOMA 310N 187289 9KHz-1GHz Jan. 05, 2022 Jan. 10, 2022 Jan. 04, 2023
(03CH04-KS)
EM18G40G Radiation
Amplifier MITEQ 060728 18~40GHz Jan. 06, 2022 Jan. 10, 2022 Jan. 05, 2023
GA (03CH04-KS)
AMF-7D-00
high gain Radiation
MITEQ 101800-30-1 2025788 1Ghz-18Ghz Jan. 05, 2022 Jan. 10, 2022 Jan. 04, 2023
Amplifier (03CH04-KS)
0P
Radiation
Amplifier Keysight 83017A MY57280106 500MHz~26.5GHz Oct. 13, 2021 Jan. 10, 2022 Oct. 12, 2022
(03CH04-KS)
AC Power Radiation
Chroma 61601 F104090004 N/A NCR Jan. 10, 2022 NCR
Source (03CH04-KS)
Radiation
Turn Table ChamPro EM 1000-T 060762-T 0~360 degree NCR Jan. 10, 2022 NCR
(03CH04-KS)
Radiation
Antenna Mast ChamPro EM 1000-A 060762-A 1 m~4 m NCR Jan. 10, 2022 NCR
(03CH04-KS)
NCR: No Calibration Required

6 Uncertainty of Evaluation
The measurement uncertainties shown below were calculated in accordance with the requirements of
ANSI 63.26-2015. All the measurement uncertainty value were shown with a coverage K=2 to indicate
95% level of confidence. The measurement data show herein meets or exceeds the CISPR
measurement uncertainty values specified in CISPR 16-4-2 and can be compared directly to specified
limit to determine compliance.
Uncertainty of Radiated Emission Measurement (30 MHz ~ 1000 MHz)

Measuring Uncertainty for a Level of
3.3dB
Confidence of 95% (U = 2Uc(y))
Uncertainty of Radiated Emission Measurement (1 GHz ~ 40 GHz)

Measuring Uncertainty for a Level of
2.8dB
Confidence of 95% (U = 2Uc(y))

Appendix A. Test Results of Conducted Test

Temperature : 22~23℃
Test Engineer : Simle Wang
Relative Humidity : 40~42%
Conducted Output Power(Average power)
LTE Band 2 Maximum Average Power [dBm]

BW [MHz] RB Size RB Offset Mod Lowest Middle Highest
20 1 0 22.30 22.25 22.29

20 1 49 22.62 22.70 22.65
20 1 99 22.24 22.25 22.27
20 50 0 QPSK 21.60 21.67 21.69
20 50 24 21.66 21.67 21.71
20 50 50 21.54 21.60 21.66
20 100 0 21.55 21.66 21.66
20 1 0 21.63 21.57 21.62
20 1 49 21.90 21.96 21.98
20 1 99 21.51 21.49 21.53
20 50 0 16-QAM 20.56 20.65 20.66
20 50 24 20.59 20.65 20.66
20 50 50 20.51 20.57 20.57
20 100 0 20.50 20.60 20.61
20 1 0 20.53 20.45 20.49
20 1 49 20.79 20.82 20.84
20 1 99 20.34 20.38 20.42
20 50 0 64QAM 19.54 19.63 19.63
20 50 24 19.58 19.61 19.63
20 50 50 19.49 19.57 19.58
20 100 0 19.48 19.62 19.58
15 1 0 22.48 22.44 22.45
15 1 37 22.67 22.69 22.66
QPSK
15 1 74 22.38 22.37 22.42
15 36 0 21.60 21.63 21.63
Sporton International Inc. (Kunshan) Page Number : B1 of B68

15 36 20 21.62 21.61 21.65

15 36 39 21.56 21.57 21.63
15 75 0 21.58 21.63 21.64
15 1 0 21.81 21.75 21.79
15 1 37 21.94 21.94 21.97
15 1 74 21.71 21.71 21.70
15 36 0 16-QAM 20.56 20.64 20.61
15 36 20 20.61 20.63 20.63
15 36 39 20.55 20.58 20.61
15 75 0 20.55 20.61 20.59
15 1 0 20.77 20.67 20.66
15 1 37 20.87 20.90 20.84
15 1 74 20.59 20.58 20.64
15 36 0 64QAM 19.57 19.61 19.60
15 36 20 19.58 19.61 19.62
15 36 39 19.55 19.59 19.60
15 75 0 19.54 19.59 19.60


10 1 0 22.50 22.50 22.49

10 1 25 22.60 22.63 22.64
10 1 49 22.42 22.43 22.48
10 25 0 QPSK 21.55 21.61 21.63
10 25 12 21.60 21.64 21.63
10 25 25 21.59 21.56 21.60
10 50 0 21.60 21.61 21.60
10 1 0 21.83 21.80 21.78
10 1 25 21.90 21.95 21.87
10 1 49 21.74 21.77 21.78
10 25 0 16-QAM 20.51 20.59 20.59
10 25 12 20.59 20.59 20.58
10 25 25 20.55 20.55 20.54
10 50 0 20.54 20.58 20.56
10 1 0 20.73 20.72 20.65
10 1 25 20.81 20.82 20.79
10 1 49 20.62 20.61 20.67
10 25 0 64QAM 19.53 19.59 19.56
10 25 12 19.57 19.59 19.59
10 25 25 19.56 19.55 19.57
10 50 0 19.53 19.56 19.55
5 1 0 22.41 22.39 22.35
5 1 12 22.64 22.66 22.65
5 1 24 22.33 22.36 22.37
5 12 0 QPSK 21.50 21.56 21.53
5 12 7 21.59 21.59 21.62
5 12 13 21.58 21.56 21.58
5 25 0 21.54 21.53 21.56
5 1 0 21.74 21.75 21.65
5 1 12 22.00 21.93 21.95
5 1 24 16-QAM 21.68 21.65 21.67
5 12 0 20.50 20.56 20.54
5 12 7 20.62 20.60 20.62

5 12 13 20.58 20.57 20.58

5 25 0 20.51 20.51 20.51
5 1 0 20.62 20.61 20.55
5 1 12 20.89 20.88 20.86
5 1 24 20.58 20.55 20.55
5 12 0 64QAM 19.53 19.54 19.50
5 12 7 19.60 19.57 19.61
5 12 13 19.56 19.55 19.55
5 25 0 19.52 19.52 19.51


3 1 0 22.53 22.45 22.45

3 1 8 22.51 22.49 22.49
3 1 14 22.47 22.46 22.47
3 8 0 QPSK 21.61 21.58 21.60
3 8 4 21.62 21.59 21.62
3 8 7 21.57 21.57 21.58
3 15 0 21.58 21.56 21.57
3 1 0 21.83 21.77 21.72
3 1 8 21.84 21.83 21.77
3 1 14 21.80 21.80 21.74
3 8 0 16-QAM 20.63 20.60 20.60
3 8 4 20.63 20.61 20.63
3 8 7 20.59 20.56 20.56
3 15 0 20.54 20.53 20.56
3 1 0 20.73 20.68 20.64
3 1 8 20.76 20.70 20.72
3 1 14 20.69 20.69 20.65
3 8 0 64QAM 19.58 19.55 19.56
3 8 4 19.58 19.58 19.57
3 8 7 19.56 19.55 19.55
3 15 0 19.54 19.53 19.52
1.4 1 0 22.62 22.62 22.35
1.4 1 3 22.63 22.66 22.39
1.4 1 5 22.63 22.54 22.30
1.4 3 0 QPSK 22.69 22.53 22.37
1.4 3 1 22.64 22.66 22.42
1.4 3 3 22.60 22.49 22.39
1.4 6 0 21.80 21.69 21.47
1.4 1 0 21.96 21.71 21.58
1.4 1 3 22.04 21.87 21.74
1.4 1 5 16-QAM 21.95 21.86 21.61
1.4 3 0 21.79 21.61 21.42
1.4 3 1 21.81 21.55 21.49

1.4 3 3 21.78 21.60 21.42

1.4 6 0 20.84 20.72 20.47
1.4 1 0 20.85 20.60 20.48
1.4 1 3 20.89 20.67 20.56
1.4 1 5 20.89 20.49 20.48
1.4 3 0 64QAM 20.80 20.66 20.48
1.4 3 1 20.87 20.59 20.50
1.4 3 3 20.80 20.52 20.46
1.4 6 0 19.77 19.61 19.43


20 1 0 22.36 22.33 22.29

20 1 49 22.64 22.75 22.60
20 1 99 22.29 22.28 22.28
20 50 0 QPSK 21.62 21.64 21.65
20 50 24 21.62 21.63 21.61
20 50 50 21.62 21.50 21.51
20 100 0 21.58 21.55 21.55
20 1 0 21.58 21.53 21.52
20 1 49 21.85 21.82 21.80
20 1 99 21.40 21.53 21.54
20 50 0 16-QAM 20.57 20.58 20.61
20 50 24 20.54 20.54 20.53
20 50 50 20.58 20.46 20.46
20 100 0 20.53 20.47 20.46
20 1 0 20.51 20.44 20.38
20 1 49 20.75 20.71 20.72
20 1 99 20.26 20.32 20.34
20 50 0 64-QAM 19.54 19.56 19.59
20 50 24 19.54 19.54 19.53
20 50 50 19.56 19.43 19.45
20 100 0 19.53 19.48 19.48
15 1 0 22.54 22.52 22.46
15 1 37 22.72 22.68 22.61
15 1 74 22.41 22.37 22.34
15 36 0 QPSK 21.58 21.58 21.58
15 36 20 21.57 21.56 21.56
15 36 39 21.54 21.51 21.44
15 75 0 21.55 21.56 21.55
15 1 0 21.79 21.68 21.66
15 1 37 21.97 21.88 21.84
15 1 74 16-QAM 21.61 21.53 21.56
15 36 0 20.53 20.54 20.57
15 36 20 20.54 20.54 20.51

15 36 39 20.49 20.44 20.41

15 75 0 20.50 20.50 20.48
15 1 0 20.69 20.61 20.56
15 1 37 20.86 20.77 20.70
15 1 74 20.53 20.48 20.46
15 36 0 64-QAM 19.52 19.53 19.54
15 36 20 19.53 19.53 19.51
15 36 39 19.50 19.43 19.41
15 75 0 19.52 19.49 19.50


10 1 0 22.53 22.51 22.47

10 1 25 22.61 22.58 22.50
10 1 49 22.47 22.42 22.37
10 25 0 QPSK 21.49 21.55 21.55
10 25 12 21.55 21.53 21.50
10 25 25 21.52 21.49 21.45
10 50 0 21.52 21.53 21.51
10 1 0 21.76 21.70 21.66
10 1 25 21.82 21.76 21.73
10 1 49 21.61 21.59 21.59
10 25 0 16-QAM 20.45 20.48 20.48
10 25 12 20.48 20.47 20.44
10 25 25 20.48 20.42 20.42
10 50 0 20.48 20.43 20.43
10 1 0 20.68 20.63 20.59
10 1 25 20.73 20.63 20.62
10 1 49 20.56 20.49 20.47
10 25 0 64-QAM 19.48 19.45 19.47
10 25 12 19.48 19.46 19.45
10 25 25 19.47 19.43 19.41
10 50 0 19.46 19.43 19.44
5 1 0 22.29 22.22 22.31
5 1 12 22.62 22.43 22.62
5 1 24 22.31 22.16 22.25
5 12 0 QPSK 21.84 21.76 21.88
5 12 7 21.81 21.84 21.79
5 12 13 21.76 21.83 21.69
5 25 0 21.84 21.82 21.51
5 1 0 22.14 21.97 21.88
5 1 12 22.29 22.23 21.91
5 1 24 16-QAM 22.16 21.99 21.93
5 12 0 20.97 20.97 20.54
5 12 7 20.95 20.98 20.61

5 12 13 20.85 20.81 20.59

5 25 0 20.97 20.73 20.53
5 1 0 21.04 20.83 21.09
5 1 12 21.33 21.19 21.13
5 1 24 20.83 20.95 21.09
5 12 0 64-QAM 19.75 19.92 19.53
5 12 7 19.81 19.91 19.61
5 12 13 19.79 19.76 19.57
5 25 0 19.73 19.73 19.52


3 1 0 22.58 22.52 22.45

3 1 8 22.54 22.52 22.47
3 1 14 22.51 22.50 22.45
3 8 0 QPSK 21.56 21.53 21.50
3 8 4 21.58 21.56 21.51
3 8 7 21.38 21.52 21.48
3 15 0 21.35 21.49 21.47
3 1 0 21.61 21.70 21.70
3 1 8 21.65 21.72 21.73
3 1 14 21.78 21.70 21.67
3 8 0 16-QAM 20.58 20.50 20.51
3 8 4 20.56 20.54 20.54
3 8 7 20.43 20.51 20.48
3 15 0 20.48 20.46 20.46
3 1 0 20.69 20.62 20.57
3 1 8 20.70 20.65 20.61
3 1 14 20.48 20.61 20.59
3 8 0 64-QAM 19.32 19.48 19.46
3 8 4 19.34 19.52 19.48
3 8 7 19.33 19.49 19.44
3 15 0 19.29 19.47 19.43
1.4 1 0 22.53 22.51 22.45
1.4 1 3 22.68 22.66 22.62
1.4 1 5 22.55 22.52 22.48
1.4 3 0 QPSK 22.65 22.60 22.55
1.4 3 1 22.72 22.67 22.62
1.4 3 3 22.65 22.62 22.57
1.4 6 0 21.69 21.62 21.60
1.4 1 0 21.82 21.74 21.71
1.4 1 3 21.96 21.84 21.85
1.4 1 5 16-QAM 21.84 21.76 21.71
1.4 3 0 21.66 21.59 21.56
1.4 3 1 21.71 21.54 21.65

1.4 3 3 21.65 21.59 21.55

1.4 6 0 20.71 20.59 20.59
1.4 1 0 20.70 20.60 20.59
1.4 1 3 20.86 20.76 20.73
1.4 1 5 20.74 20.61 20.61
1.4 3 0 64-QAM 20.71 20.64 20.61
1.4 3 1 20.73 20.69 20.66
1.4 3 3 20.69 20.63 20.59
1.4 6 0 19.64 19.55 19.53

ERP/EIRP
LTE Band 2 (GT - LC = -0.67 dB) QPSK

Bandwidth 1.4M 3M 5M
18607 18900 19193 18615 18900 19185 18625 18900 19175

Channel
(Low) (Mid) (High) (Low) (Mid) (High) (Low) (Mid) (High)
Frequency
1850.7 1880 1909.3 1851.5 1880 1908.5 1852.5 1880 1907.5
(MHz)
Conducted
22.69 22.53 22.37 22.53 22.45 22.45 22.64 22.66 22.65
Power (dBm)
Conducted
0.1858 0.1791 0.1726 0.1791 0.1758 0.1758 0.1837 0.1845 0.1841
Power (Watts)
EIRP(dBm) 22.02 21.86 21.70 21.86 21.78 21.78 21.97 21.99 21.98
EIRP(Watts) 0.1592 0.1535 0.1479 0.1535 0.1507 0.1507 0.1574 0.1581 0.1578

Bandwidth 10M 15M 20M
18650 18900 19150 18675 18900 19125 18650 18900 19100

Channel
Frequency
1855 1880 1905 1857.5 1880 1902.5 1860 1880 1900
(MHz)
Conducted
22.60 22.63 22.64 22.67 22.69 22.66 22.62 22.70 22.65
Power (dBm)
Conducted
Power 0.1820 0.1832 0.1837 0.1849 0.1858 0.1845 0.1828 0.1862 0.1841
(Watts)
EIRP(dBm) 21.93 21.96 21.97 22.00 22.02 21.99 21.95 22.03 21.98
EIRP(Watts) 0.1560 0.1570 0.1574 0.1585 0.1592 0.1581 0.1567 0.1596 0.1578

LTE Band 2 (GT - LC = -0.67 dB) 16QAM

18607 18900 19193 18615 18900 19185 18625 18900 19175

Channel
Frequency
1850.7 1880 1909.3 1851.5 1880 1908.5 1852.5 1880 1907.5
(MHz)
Conducted
22.04 21.87 21.74 21.84 21.83 21.77 22.00 21.93 21.95
Power (dBm)
Conducted
Power 0.1600 0.1538 0.1493 0.1528 0.1524 0.1503 0.1585 0.1560 0.1567
(Watts)
EIRP(dBm) 21.37 21.20 21.07 21.17 21.16 21.10 21.33 21.26 21.28
EIRP(Watts) 0.1371 0.1318 0.1279 0.1309 0.1306 0.1288 0.1358 0.1337 0.1343

18650 18900 19150 18675 18900 19125 18650 18900 19100

Channel
Frequency
1855 1880 1905 1857.5 1880 1902.5 1860 1880 1900
(MHz)
Conducted
21.90 21.95 21.87 21.94 21.94 21.97 21.90 21.96 21.98
Power (dBm)
Conducted
Power 0.1549 0.1567 0.1538 0.1563 0.1563 0.1574 0.1549 0.1570 0.1578
(Watts)
EIRP(dBm) 21.23 21.28 21.20 21.27 21.27 21.30 21.23 21.29 21.31
EIRP(Watts) 0.1327 0.1343 0.1318 0.1340 0.1340 0.1349 0.1327 0.1346 0.1352


18607 18900 19193 18615 18900 19185 18625 18900 19175

Channel
Frequency
1850.7 1880 1909.3 1851.5 1880 1908.5 1852.5 1880 1907.5
(MHz)
Conducted
20.89 20.67 20.56 20.76 20.70 20.72 20.89 20.88 20.86
Power (dBm)
Conducted
Power 0.1227 0.1167 0.1138 0.1191 0.1175 0.1180 0.1227 0.1225 0.1219
(Watts)
EIRP(dBm) 20.22 20.00 19.89 20.09 20.03 20.05 20.22 20.21 20.19
EIRP(Watts) 0.1052 0.1000 0.0975 0.1021 0.1007 0.1012 0.1052 0.1050 0.1045

18650 18900 19150 18675 18900 19125 18650 18900 19100

Channel
Frequency
1855 1880 1905 1857.5 1880 1902.5 1860 1880 1900
(MHz)
Conducted
20.81 20.82 20.79 20.87 20.90 20.84 20.79 20.82 20.84
Power (dBm)
Conducted
Power 0.1205 0.1208 0.1199 0.1222 0.1230 0.1213 0.1199 0.1208 0.1213
(Watts)
EIRP(dBm) 20.14 20.15 20.12 20.20 20.23 20.17 20.12 20.15 20.17
EIRP(Watts) 0.1033 0.1035 0.1028 0.1047 0.1054 0.1040 0.1028 0.1035 0.1040


19957 20175 20393 19965 20175 20385 19975 20175 20375
Channel
Frequency
1710.7 1732.5 1754.3 1711.5 1732.5 1753.5 1712.5 1732.5 1752.5
(MHz)
Conducted
22.72 22.67 22.62 22.58 22.52 22.45 22.62 22.43 22.62
Power (dBm)
Conducted
Power 0.1871 0.1849 0.1828 0.1811 0.1786 0.1758 0.1828 0.1750 0.1828
(Watts)
EIRP(dBm) 22.22 22.17 22.12 22.08 22.02 21.95 22.12 21.93 22.12
EIRP(Watts) 0.1667 0.1648 0.1629 0.1614 0.1592 0.1567 0.1629 0.1560 0.1629

20000 20175 20350 20025 20175 20325 20050 20175 20300
Channel
Frequency
1715 1732.5 1750 1717.5 1732.5 1747.5 1720 1732.5 1745
(MHz)
Conducted
22.61 22.58 22.50 22.72 22.68 22.61 22.64 22.75 22.60
Power (dBm)
Conducted
Power 0.1824 0.1811 0.1778 0.1871 0.1854 0.1824 0.1837 0.1884 0.1820
(Watts)
EIRP(dBm) 22.11 22.08 22.00 22.22 22.18 22.11 22.14 22.25 22.10
EIRP(Watts) 0.1626 0.1614 0.1585 0.1667 0.1652 0.1626 0.1637 0.1679 0.1622


19957 20175 20393 19965 20175 20385 19975 20175 20375
Channel
Frequency
1710.7 1732.5 1754.3 1711.5 1732.5 1753.5 1712.5 1732.5 1752.5
(MHz)
Conducted
21.96 21.84 21.85 21.78 21.70 21.67 22.29 22.23 21.91
Power (dBm)
Conducted
Power 0.1570 0.1528 0.1531 0.1507 0.1479 0.1469 0.1694 0.1671 0.1552
(Watts)
EIRP(dBm) 21.46 21.34 21.35 21.28 21.20 21.17 21.79 21.73 21.41
EIRP(Watts) 0.1400 0.1361 0.1365 0.1343 0.1318 0.1309 0.1510 0.1489 0.1384

20000 20175 20350 20025 20175 20325 20050 20175 20300
Channel
Frequency
1715 1732.5 1750 1717.5 1732.5 1747.5 1720 1732.5 1745
(MHz)
Conducted
21.82 21.76 21.73 21.97 21.88 21.84 21.85 21.82 21.80
Power (dBm)
Conducted
Power 0.1521 0.1500 0.1489 0.1574 0.1542 0.1528 0.1531 0.1521 0.1514
(Watts)
EIRP(dBm) 21.32 21.26 21.23 21.47 21.38 21.34 21.35 21.32 21.30
EIRP(Watts) 0.1355 0.1337 0.1327 0.1403 0.1374 0.1361 0.1365 0.1355 0.1349


19957 20175 20393 19965 20175 20385 19975 20175 20375
Channel
Frequency
1710.7 1732.5 1754.3 1711.5 1732.5 1753.5 1712.5 1732.5 1752.5
(MHz)
Conducted
20.86 20.76 20.73 20.70 20.65 20.61 21.33 21.19 21.13
Power (dBm)
Conducted
Power 0.1219 0.1191 0.1183 0.1175 0.1161 0.1151 0.1358 0.1315 0.1297
(Watts)
EIRP(dBm) 20.36 20.26 20.23 20.20 20.15 20.11 20.83 20.69 20.63
EIRP(Watts) 0.1086 0.1062 0.1054 0.1047 0.1035 0.1026 0.1211 0.1172 0.1156

20000 20175 20350 20025 20175 20325 20050 20175 20300
Channel
Frequency
1715 1732.5 1750 1717.5 1732.5 1747.5 1720 1732.5 1745
(MHz)
Conducted
20.73 20.63 20.62 20.86 20.77 20.70 20.75 20.71 20.72
Power (dBm)
Conducted
Power 0.1183 0.1156 0.1153 0.1219 0.1194 0.1175 0.1189 0.1178 0.1180
(Watts)
EIRP(dBm) 20.23 20.13 20.12 20.36 20.27 20.20 20.25 20.21 20.22
EIRP(Watts) 0.1054 0.1030 0.1028 0.1086 0.1064 0.1047 0.1059 0.1050 0.1052

LTE Band 2
Conducted Band Edge

LTE Band 2 / 1.4MHz / QPSK
Lowest Band Edge / 1RB Highest Band Edge / 1RB
Lowest Band Edge / Full RB Highest Band Edge / Full RB

LTE Band 2 / 1.4MHz / 16QAM

Lowest Band Edge / 1 RB Highest Band Edge / 1 RB

LTE Band 2 / 1.4MHz / 64QAM


LTE Band 2 / 3MHz / QPSK

Lowest Band Edge / 1RB Highest Band Edge / 1 RB

LTE Band 2 / 3MHz / 16QAM

Lowest Band Edge / 1 RB Highest Band Edge /1 RB


Lowest Band Edge / 1 RB Highest Band Edge /1 RB

























LTE Band 2 / 1.4MHz

Lowest Channel / QPSK Middle Channel / QPSK
Highest Channel / QPSK

LTE Band 2 / 3MHz


LTE Band 2 / 5MHz


LTE Band 2 / 10MHz



Test Zte

Uploaded by

Copyright:

Available Formats

Test Zte

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Test Zte

Uploaded by

Copyright:

Available Formats

FCC RF Test Report Report No.

FCC RF Test Report

Reviewed by: Jason Jia / Supervisor

Approved by: Alex Wang / Manager

Sporton International Inc. (Kunshan)

Sporton International Inc. (Kunshan) Page Number : 1 of 24

Sporton International Inc. (Kunshan) Page Number : 2 of 24

REPORT NO. VERSION DESCRIPTION ISSUED DATE

FG1D0702 Rev. 01 Initial issue of report Jan. 25, 2022

Sporton International Inc. (Kunshan) Page Number : 3 of 24

SUMMARY OF TEST RESULT

§2.1046 Conducted Output Power - Report Only -

Equivalent Isotropic Radiated Power

3.5 §24.232(d) Peak-to-Average Ratio <13 dB PASS -

3.6 §2.1049 Occupied Bandwidth - Report Only -

Sporton International Inc. (Kunshan) Page Number : 4 of 24

Sporton International Inc. (Kunshan) Page Number : 5 of 24

1.3 Product Feature of Equipment Under Test

1.4 Product Specification of Equipment Under Test

Sporton International Inc. (Kunshan) Page Number : 6 of 24

Type of Modulation QPSK / 16QAM / 64QAM

1.5 Modification of EUT

1.6 Maximum ERP/EIRP Power and Emission Designator

Sporton International Inc. (Kunshan) Page Number : 7 of 24

1.7 Testing Location

Test Firm Sporton International Inc. (Kunshan)

No. 1098, Pengxi North Road, Kunshan Economic Development Zone

Jiangsu Province 215300 People’s Republic of China

FCC Test Firm

1.8 Test Software

1. 03CH04-KS AUDIX E3 6.2009-8-24a

1.9 Applicable Standards

Sporton International Inc. (Kunshan) Page Number : 8 of 24

2 Test Configuration of Equipment Under Test

Radiated 2 Worst Case v

Sporton International Inc. (Kunshan) Page Number : 9 of 24

2.2 Connection Diagram of Test System

Cradle Earphone iPod WLAN AP Monitor

This example is connection diagram of EUT test configurations.

2.3 Support Unit used in test configuration and system

2. LTE Base Station Anritsu MT8820C N/A N/A Unshielded, 1.8 m

2.4 Measurement Results Explanation Example

The spectrum analyzer offset is derived from RF cable loss.

Sporton International Inc. (Kunshan) Page Number : 10 of 24

2.5 Frequency List of Low/Middle/High Channels

LTE Band 4 Channel and Frequency List

Sporton International Inc. (Kunshan) Page Number : 11 of 24

3 Conducted Test Items

3.2 Test Setup

3.2.2 Peak-to-Average Ratio, Occupied Bandwidth ,Conducted Band-Edge and

3.2.3 Frequency Stability

3.3 Test Result of Conducted Test

Sporton International Inc. (Kunshan) Page Number : 12 of 24

3.4 Conducted Output Power and ERP/EIRP

3.4.2 Test Procedures

Sporton International Inc. (Kunshan) Page Number : 13 of 24

3.5 Peak-to-Average Ratio

3.5.2 Test Procedures

Sporton International Inc. (Kunshan) Page Number : 14 of 24