Cat Electronic Technician 2015A v1.

0
Product Status Report

27/02/2024 2:11 p. m.

Product Status Report

Parameter Value
Product ID FBA03279
Equipment ID fba03279
Comments Descarga de datos 27022024

Monitor
Parameter Value
ECM Serial Number 072E0130EE
Personality Module Part Number 2602161-00

Hyd Pump Control 320C (SBN02393)

Parameter Value
Product ID SBN02393
ECM Part Number 1573165-05
ECM Serial Number 00211857EG
Software Group Part Number 2475305-00
Software Group Release Date SEP2004
Software Group Description 320C HEX CONTROL
Active Diagnostic Codes Present Yes

Logged Diagnostic Codes [Diagnostic Clock = Unavailable hours] - Hyd Pump Control 320C
(SBN02393)
Code Description Occ. First Last
96- 3 Fuel Level Sensor : Voltage Above Normal 1 0 0
110-10 Engine Coolant Temperature Sensor : Abnormal 1 0 0
Rate of Change
167- 8 Alternator Charging Voltage Sensor : Abnormal 1 0 0
Frequency, Pulse Width, or Period
168- 5 Electrical System Voltage : Current Below Normal 1 0 0
190- 8 Engine Speed Sensor : Abnormal Frequency, 1 0 0
Pulse Width, or Period
376- 5 Travel Alarm : Current Below Normal 1 0 0
587- 3 Engine Governor Position Sensor : Voltage Above 1 0 0
Normal
588- 9 Monitor System Display : Abnormal Update Rate 1 0 0
1161- 4 Front Hydraulic Pump Pressure Sensor : Voltage 1 0 0
Below Normal
1162- 4 Rear Hydraulic Pump Pressure Sensor : Voltage 1 0 0
Below Normal
Logged Event Codes [Diagnostic Clock = Unavailable hours] - Hyd Pump Control 320C
(SBN02393)
Code Description Occ. First Last
E015 High Engine Coolant Temperature Derate 1 0 0
E179 Alternator Not Charging 1 0 0

Active Diagnostic Codes - Hyd Pump Control 320C (SBN02393)

Code Description
1161- 4 Front Hydraulic Pump Pressure Sensor : Voltage Below Normal

Current Totals - Hyd Pump Control 320C (SBN02393)

Description Value Unit
Engine Maintenance Hours 30998 hours
Engine Oil Hours 19164 hours
Engine Oil Filter Hours 19164 hours
Engine Coolant Hours 30998 hours
Fuel/ Water Separator Hours 0 hours
Fuel Filter Hours 19164 hours
Hydraulic Pump Hours 30998 hours
Hydraulic Pilot Oil Filter Hours 19164 hours
Hydraulic Case Drain Oil Filter 19164 hours
Hours
Return Hydraulic Oil Filter 3683 hours
Hours
Hydraulic Oil Hours 20439 hours
Final Drive Oil Hours 27572 hours
Swing Drive Oil Hours 27572 hours
Travel Motor Hours 2299 hours
Tool #1 Hours 0 hours
Tool #2 Hours 0 hours
Tool #3 Hours 0 hours
Tool #4 Hours 0 hours
Tool #5 Hours 0 hours

Configuration - Hyd Pump Control 320C (SBN02393)

Description Value Unit
Product ID SBN02393
Hydraulic Oil Type Mineral Oil
Travel Alarm Installation Status Installed
Water Separator Level Switch Normally Open
Configuration
Fuel Filter Differential Pressure Switch Not Installed
Config
Secondary Fuel Filter Differential Pressure Not Installed
Switch Config
High Pressure Hydraulic Oil Filter Switch Normally Open
Config
Auto Lube System Installation Status Not Installed
Machine Overload Pressure Sensor Not Installed
Installation
Machine Application Configuration Bucket
Attachment Tool ECM Installation Status Not Installed
Main Pump Flow Limitation Pressure Not Installed
Solenoid Installation Status
Attachment Valve #1 Configuration F2 - One Way or Two Way
Attachment Valve #2 Configuration F2 - One Way or Two Way
Attachment Valve #3 Configuration F4 - One Way or Two Way
Attachment Valve #4 Configuration F3 - One Way or Two Way
Attachment Valve #1 Combiner Valve #2 Combined with Valve #1
Configuration
Travel Speed Shift Low Delay 0,4 sec
Travel Speed Shift High Delay 0,4 sec
Travel Speed Shift Low Pres 2418 psi
Travel Speed Shift High Pressure 4622 psi
One Touch Engine Speed Setting 1000 rpm
AESC Setting 1300 rpm
AESC Delay Time 3,0 sec
Throttle Dial Position 1 Engine Speed 1000 rpm
Throttle Dial Position 2 Engine Speed 1100 rpm
Throttle Dial Position 3 Engine Speed 1200 rpm
Throttle Dial Position 4 Engine Speed 1300 rpm
Throttle Dial Position 5 Engine Speed 1470 rpm
Throttle Dial Position 6 Engine Speed 1590 rpm
Throttle Dial Position 7 Engine Speed 1700 rpm
Throttle Dial Position 8 Engine Speed 1800 rpm
Throttle Dial Position 9 Engine Speed 1900 rpm
Throttle Dial Position 10 Engine Speed 2000 rpm
Throttle Dial Position 1 Hydraulic System 20,0 %
Torque Percentage
Throttle Dial Position 2 Hydraulic System 40,0 %
Torque Percentage
Throttle Dial Position 3 Hydraulic System 60,0 %
Torque Percentage
Throttle Dial Position 4 Hydraulic System 81,2 %
Torque Percentage
Throttle Dial Position 5 Hydraulic System 86,4 %
Torque Percentage
Throttle Dial Position 6 Hydraulic System 86,4 %
Torque Percentage
Throttle Dial Position 7 Hydraulic System 86,4 %
Torque Percentage
Throttle Dial Position 8 Hydraulic System 86,4 %
Torque Percentage
Throttle Dial Position 9 Hydraulic System 86,4 %
Torque Percentage
Throttle Dial Position 10 Hydraulic System 105,0 %
Torque Percentage
Engine Oil Recommended Maintenance 500 hours
Interval
Engine Oil Filter Recommended 500 hours
Maintenance Interval
Engine Coolant Recommended 3000 hours
Maintenance Interval
Fuel/ Water Separator Recommended 0 hours
Maint Interval
Fuel Filter Recommended Maintenance 500 hours
Interval
Hydraulic Pilot Oil Filter Recommended 1000 hours
Maintenance Interval
Hydraulic Case Drain Oil Filter 1000 hours
Recommended MI
Return Hyd Oil Filter Recommended Maint 1000 hours
Interval
Final Drive Oil Recommended 2000 hours
Maintenance Interval
Hydraulic Oil Recommended Maintenance 2000 hours
Interval
Swing Drive Oil Recommended 1000 hours
Maintenance Interval

Tool Configuration - Hyd Pump Control 320C (SBN02393)

Description Value Unit
Tool Program Name 0
Maximum Throttle Dial 10
Throttle Dial Flow Control On
Underspeed Enable Enabled
Two Pump Flow Combine Disabled
Enable
Initial Tool Program Medium 5 %
Pressure Circuit Main Pump
Torque Reduction
Total Tool Program Medium 30 %
Pressure Circuit Main Pump
Torque Reduction
Attachment Valve #1 Flow 42 gal/min
Setting
Attachment Valve #1 Multi- 0 gal/min
Operation Additional Flow
Valve #1 Nominal Pressure 2321 psi
Attachment Valve #3 Flow 11 gal/min
Setting
Attachment Valve #3 Multi- 0 gal/min
Operation Additional Flow
Valve #3 Nominal Pressure 2321 psi

Tool Configuration - Hyd Pump Control 320C (SBN02393)

Description Value Unit
Tool Program Name 0
Maximum Throttle Dial 10
Throttle Dial Flow Control On
Underspeed Enable Enabled
Two Pump Flow Combine Enabled
Enable
Initial Tool Program Medium 5 %
Pressure Circuit Main Pump
Torque Reduction
Total Tool Program Medium 30 %
Pressure Circuit Main Pump
Torque Reduction
Attachment Valve #1 Flow 42 gal/min
Setting
Attachment Valve #1 Multi- 0 gal/min
Operation Additional Flow
Valve #1 Nominal Pressure 2321 psi
Attachment Valve #3 Flow 11 gal/min
Setting
Attachment Valve #3 Multi- 0 gal/min
Operation Additional Flow
Valve #3 Nominal Pressure 2321 psi

Tool Configuration - Hyd Pump Control 320C (SBN02393)

Description Value Unit
Tool Program Name 0
Maximum Throttle Dial 10
Throttle Dial Flow Control On
Underspeed Enable Enabled
Two Pump Flow Combine Enabled
Enable
Initial Tool Program Medium 5 %
Pressure Circuit Main Pump
Torque Reduction
Total Tool Program Medium 30 %
Pressure Circuit Main Pump
Torque Reduction
Attachment Valve #1 Flow 42 gal/min
Setting
Attachment Valve #1 Multi- 0 gal/min
Operation Additional Flow
Valve #1 Nominal Pressure 2321 psi
Attachment Valve #3 Flow 11 gal/min
Setting
Attachment Valve #3 Multi- 0 gal/min
Operation Additional Flow
Valve #3 Nominal Pressure 2321 psi

Tool Configuration - Hyd Pump Control 320C (SBN02393)

Description Value Unit
Tool Program Name 0
Maximum Throttle Dial 10
Throttle Dial Flow Control On
Underspeed Enable Enabled
Two Pump Flow Combine Enabled
Enable
Initial Tool Program Medium 5 %
Pressure Circuit Main Pump
Torque Reduction
Total Tool Program Medium 30 %
Pressure Circuit Main Pump
Torque Reduction
Attachment Valve #1 Flow 42 gal/min
Setting
Attachment Valve #1 Multi- 0 gal/min
Operation Additional Flow
Valve #1 Nominal Pressure 2321 psi
Attachment Valve #3 Flow 11 gal/min
Setting
Attachment Valve #3 Multi- 0 gal/min
Operation Additional Flow
Valve #3 Nominal Pressure 2321 psi

Tool Configuration - Hyd Pump Control 320C (SBN02393)

Description Value Unit
Tool Program Name 0
Maximum Throttle Dial 10
Throttle Dial Flow Control On
Underspeed Enable Enabled
Two Pump Flow Combine Enabled
Enable
Initial Tool Program Medium 5 %
Pressure Circuit Main Pump
Torque Reduction
Total Tool Program Medium 30 %
Pressure Circuit Main Pump
Torque Reduction
Attachment Valve #1 Flow 42 gal/min
Setting
Attachment Valve #1 Multi- 0 gal/min
Operation Additional Flow
Valve #1 Nominal Pressure 2321 psi
Attachment Valve #3 Flow 11 gal/min
Setting
Attachment Valve #3 Multi- 0 gal/min
Operation Additional Flow
Valve #3 Nominal Pressure 2321 psi