Scribd Logo
Upload

Welcome to Scribd!

  • 14 views

    Procedure For Vacuum Testing

    Uploaded by

    MANIMARAN QC
    The document provides a procedure for vacuum testing expansion joints, including test objectives, requirements, test arrangements, acceptance norms, and reporting requirements. The procedure specifies ambient temperature testing, calibrated pressure gauges, test durations per drawings, fixture and expansion joint setup, creating and maintaining vacuum, and reporting observations and results.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    Procedure For Vacuum Testing

    Uploaded by

    MANIMARAN QC
    14 views2 pages
    The document provides a procedure for vacuum testing expansion joints, including test objectives, requirements, test arrangements, acceptance norms, and reporting requirements. The procedure specifies ambient temperature testing, calibrated pressure gauges, test durations per drawings, fixture and expansion joint setup, creating and maintaining vacuum, and reporting observations and results.

    Original Title

    PROCEDURE FOR VACUUM TESTING-

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides a procedure for vacuum testing expansion joints, including test objectives, requirements, test arrangements, acceptance norms, and reporting requirements. The procedure specifies ambient temperature testing, calibrated pressure gauges, test durations per drawings, fixture and expansion joint setup, creating and maintaining vacuum, and reporting observations and results.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    14 views2 pages

    Procedure For Vacuum Testing

    Uploaded by

    MANIMARAN QC
    The document provides a procedure for vacuum testing expansion joints, including test objectives, requirements, test arrangements, acceptance norms, and reporting requirements. The procedure specifies ambient temperature testing, calibrated pressure gauges, test durations per drawings, fixture and expansion joint setup, creating and maintaining vacuum, and reporting observations and results.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 2

    PROCEDURE FOR VACUUM TESTING

    DOC NO : LSI/VT/001/REV.0 DT 23.05.2019

    PROCEDURE FOR VACUUM TESTING

    For CUSTOMER
    For LONESTAR INDUSTRIES

    Page No : 1 of 4
    PROCEDURE FOR VACUUM TESTING
    DOC NO : LSI/VT/001/REV.0 DT 23.05.2019

    A. TEST OBJECTIVE:
    The Test Objective is to verify the leak tightness and the strength of Expansion joints
    at the specified vacuum and Duration at ambient / room temperature.

    B. TEST REQUIREMENT:

    1. Test temperature shall be ambient

    2. The Pressure Gauge(s) being used shall be calibrated with the availability of up to date Calibration Certifi-
    cate for review

    3. Test Duration shall be as per drawing

    C Test Arrangement & Testing

    1. The test fixture has a bottom stationary plate and top sliding plate. Both top and bottom plates are connected
    by restraining rods with Nuts & Lock Nuts. The top plate shall have outlet vent connections and the Bottom
    plates have inlet vent connections.

    2. The Expansion Joint will placed on the bottom plate with sponge rubber seal between the Pipe of the
    Expansion Joint and bottom plate. A similar sponge rubber seal will be placed between the Pipe of the
    Expansion Joint and top plate as shown in Sketch – (Page No : 3 of 4)

    3. The Expansion Joint, if required will be incorporated with temporary restraints to prevent the axial
    compression and to get the required sealing between the Pipes and fixture plates.

    4. The top plate will be brought close to the Expansion Joint, the Nuts/Lock Nuts in the Restraining Rods will
    be tightened to get the required sealing.

    5. Vacuum will be created and maintained as per the drawing / QAP requirement.

    D. ACCEPTANCE NORM:

    Bellows surface and Weld Joint between the Bellows and Pipes should be hold during the vacuum test duration
    With out leakage or No drop in vacuum..

    E. REPORTING:

    Observation and result will be recorded in the test report. The typical format of Report is as per the annexure.

    Page No 2 of 4

    You might also like