Isis

ISIS Tutorial
Philip Smith <[email protected]>

MENOG 4
5th-9th April 2009
Bahrain
MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 1

Presentation Slides
 Will be available on
ftp://ftp-eng.cisco.com
/pfs/seminars/MENOG4-ISIS-Tutorial.pdf
And on the MENOG website
 Feel free to ask questions any time

Agenda
 Comparing ISIS and OSPF

 Introduction to ISIS
 ISIS Best Practices

Comparing ISIS and OSPF
Both Link State Protocols use the Dijkstra SPF

Algorithm
So what’s the difference then??

What Is IS-IS ?
 Intermediate System to Intermediate System

 An “IS” is ISO terminology for a router
 IS-IS was originally designed for use as a dynamic
routing protocol for ISO CLNP, defined in the ISO
10589 standard
 Later adapted to carry IP prefixes in addition to CLNP
(known as Integrated or Dual IS-IS) as described in
RFC 1195
 Predominantly used in ISP environment

IS-IS Timeline
 1978ish “New” Arpanet Algorithm

Eric Rosen et al
 1986 to 90 Decnet Phase V
Radia Perlman, Mike Shand
 1987 ISO 10589 (IS-IS)
Dave Oran
 1990 RFC 1195 (Integrated IS-IS)
Ross Callon, Chris Gunner
 1990 to present: All sorts of enhancements
Everyone contributed!
 2008 RFC5308 adds IPv6 support
And RFC5120 adds Multi-Topology Routing support

What Is OSPF ?
 Open Shortest Path First

 Link State Protocol using the Shortest Path First
algorithm (Dijkstra) to calculate loop-free routes
 Used purely within the TCP/IP environment
 Designed to respond quickly to topology changes but
using minimal protocol traffic
 Used in both Enterprise and ISP Environment

OSPF Timeline
 Development began in 1987 by IETF

 OSPFv1 published in 1989 with RFC 1131
 OSPFv2 published in 1991 with RFC 1247
 Further enhancements to OSPFv2 in 1994 with RFC
1583 and in 1997 with RFC 2178
 Last revision was in 1998 with RFC 2328 to fix minor
problems
 All above OSPF RFCs authored by John Moy
 RFC2740 introduced OSPFv3 (for IPv6) in 1999,
replaced by RFC5340 in 2008

IS-IS & OSPF:
Similarities
 Both are Interior Gateway Protocols (IGP)

They distribute routing information between routers belonging to
a single Autonomous System (AS)
 With support for:

Classless Inter-Domain Routing (CIDR)
Variable Subnet Length Masking (VLSM)
Authentication
Multi-path
IP unnumbered links

IS-IS and OSPF Terminology
OSPF ISIS
 Host  End System (ES)
 Router  Intermediate System (IS)
 Link  Circuit
 Packet  Protocol Data Unit (PDU)
 Designated router (DR)  Designated IS (DIS)
 Backup DR (BDR)  N/A (no BDIS is used)
 Link-State Advertisement (LSA)  Link-State PDU (LSP)
 Hello packet  IIH PDU
 Database Description (DBD)  Complete sequence number
PDU (CSNP)

IS-IS and OSPF Terminology (Cont.)
OSPF ISIS
 Area  Sub domain (area)
 Non-backbone area  Level-1 area
 Backbone area  Level-2 Sub domain (backbone)
 Area Border Router (ABR)  L1L2 router
 Autonomous System  Any IS
Boundary Router (ASBR)

Transport
 OSPF uses IP Protocol 89 as transport
Data Link Header IP Header OSPF Header OSPF Data
 IS-IS is directly encapsulated in Layer 2
Data Link Header IS-IS Header IS-IS Data

For Service Providers
 Which IGP should an ISP choose?

Both OSPF and ISIS use Dijkstra SPF algorithm
Exhibit same convergence properties
ISIS less widely implemented on router platforms
ISIS runs on data link layer, OSPF runs on IP layer
Biggest ISPs tend to use ISIS
Main ISIS implementations more tuneable than equivalent
OSPF implementations

How to choose an IGP?
 OSPF
Rigid area design - all networks must have area 0 core, with
sub-areas distributed around
Suits ISPs with central high speed core network linking regional
PoPs
Teaches good routing protocol design practices
 ISIS
Relaxed two level design - L2 routers must be linked through
the backbone
Suits ISPs with “stringy” networks, diverse infrastructure, etc,
not fitting central core model of OSPF
More flexible than OSPF, but easier to make mistakes too

Other considerations
 ISIS runs on link layer

Not possible to “attack” the IGP using IP as with OSPF
 ISIS’s NSAP addressing scheme avoids dependencies

on IP as with OSPF
 Because biggest ISPs use ISIS, it tends to get new
optimisation features before OSPF does

Introduction to ISIS

IS-IS Standards History
 ISO 10589 specifies OSI IS-IS routing protocol for CLNS traffic
Tag/Length/Value (TLV) options to enhance the protocol
A Link State protocol with a 2 level hierarchical architecture.
 RFC 1195 added IP support
I/IS-IS runs on top of the Data Link Layer
Requires CLNP to be configured
 RFC5308 adds IPv6 address family support to IS-IS
 RFC5120 defines Multi-Topology concept for IS-IS
Permits IPv4 and IPv6 topologies which are not identical

ISIS Levels
 ISIS has a 2 layer hierarchy

Level-2 (the backbone)
Level-1 (the areas)
 A router can be
Level-1 (L1) router
Level-2 (L2) router
Level-1-2 (L1L2) router

ISIS Levels
 Level-1 router
Has neighbours only on the same area
Has a level-1 LSDB with all routing information for the area
 Level-2 router
May have neighbours in the same or other areas
Has a Level-2 LSDB with all routing information about inter-area
 Level-1-2 router
May have neighbours on any area.
Has two separate LSDBs: level-1 LSDB & level-2 LSDB

Backbone & Areas
 ISIS does not have a backbone area as such (like

OSPF)
 Instead the backbone is the contiguous collection of
Level-2 capable routers
 ISIS area borders are on links, not routers
 Each router is identified with Network Entity Title (NET)
NET is an NSAP where the n-selector is 0

L1, L2, and L1L2 Routers
Area-3
L1-only
L1L2
Area-2 L2-only
L1L2
L1L2
L1-only
Area-4
L1L2 L1-only
Area-1
L1L2
L1-only

NSAP and Addressing
 NSAP: Network Service Access Point

Total length between 8 and 20 bytes
Area Address: variable length field (up to 13 bytes)
System ID: defines an ES or IS in an area.
NSEL: N-selector. identifies a network service user (transport entity or the IS
network entity itself)
 NET: the address of the network entity itself

An Addressing Example
49.0f01.0002.4444.4444.4444.00 Area 3
49.0f01.0003.6666.6666.6666.00
Area 2
49.0f01.0002.3333.3333.3333.00
49.0f01.0004.7777.7777.7777.00 Area 4
49.0f01.0001.2222.2222.2222.00
49.0f01.0004.8888.8888.8888.00
Area 1
49.0f01.0001.1111.1111.1111.00

Addressing Common Practices
 ISPs typically choose NSAP addresses thus:

First 8 bits – pick a number (usually 49)
Next 16 bits – area
Next 48 bits – router loopback address
Final 8 bits – zero
 Example:
NSAP: 49.0001.1921.6800.1001.00
Router: 192.168.1.1 (loopback) in Area 1

Adjacencies
 Hello PDU IIHs are exchanged between routers to form

adjacencies
ISIS adjacency through IIH
 Area addresses are exchanged in IIH PDUs

Link State PDU (LSP)
 Each router creates an LSP and flood it to neighbours

 A level-1 router will create level-1 LSP(s)
 A level-2 router will create level-2 LSP(s)
 A level-1-2 router will create
level-1 LSP(s) and
level-2 LSP(s)

LSP Header
 LSPs have  The LSP header contains

Fixed header LSP-id
TLV coded contents Sequence number
Remaining Lifetime
Checksum
Type of LSP (level-1, level-2)
Attached bit
Overload bit

LSP Contents
 The LSP contents are coded as TLV (Type, Length,

Value)
Area addresses
IS neighbors
Authentication Info

LSDB content
 Each router maintains a separate LSDB for level-1 and

level-2 LSPs
 LSP headers and contents
 SRM bits: set per interface when router has to flood this
LSP
 SSN bits: set per interface when router has to send a
PSNP for this LSP

Flooding of LSPs
 New LSPs are flooded to all neighbors

 It is necessary that all routers get all LSPs
 Each LSP has a sequence number
 2 kinds of flooding
Flooding on a p2p link
Flooding on LAN

Flooding on a p2p link
 Once the adjacency is established both routers send

CSNP packet
 Missing LSPs are sent by both routers if not present in
the received CSNP
 Missing LSPs may be requested through PSNP

Flooding on a LAN
 There’s a Designated Router (DIS)

 DIS election is based on priority
Best practice is to select two routers and give them higher
priority – then in case of failure one provides deterministic
backup to the other
 Tie break is by the highest MAC address

 DIS has two tasks
Conducting the flooding over the LAN
Creating and updating a special LSP describing the LAN
topology (Pseudonode LSP)
 Pseudonode represents LAN (created by the DIS)

Flooding on a LAN
 DIS conducts the flooding over the LAN

 DIS multicasts CSNP every 10 seconds
 All routers in the LAN check the CSNP against their
own LSDB (and may ask specific re-transmissions with
PSNPs)

Complete Sequence Number PDU
 Describes all LSPs in your LSDB (in range)

 If LSDB is large, multiple CSNPs are sent
 Used at 2 occasions
Periodic multicast by DIS (every 10 seconds) to synchronise
LSDB over LAN subnets
On p2p links when link comes up

Partial Sequence Number PDUs
 PSNPs Exchanged on p2p links (ACKs)

 Two functions
Acknowledge receipt of an LSP
Request transmission of latest LSP
 PSNPs describe LSPs by its header
LSP identifier
Sequence number
Remaining lifetime
LSP checksum

Configuration
Area-2 Area-1 Area-3

Rtr-C
Rtr-A Rtr-B
 L1, L2, L1-L2

By default cisco routers will be L1L2 routers
Routers can be manually configured to behave as
Level-1 only, Level-2 only, Level-1-2
This is what most ISPs do
Configuration can be done per interface or at the router level

Configuration for A&B L1L2 routers
Rtr-B Rtr-C
Area 49.0001 Area 49.0002
Router-B
interface Loopback0 Rtr-A Rtr-D
ip address 192.168.1.1 255.255.255.255 L1routers
!
Interface Pos2/0/0 Router-A
ip address 192.168.222.1 255.255.255.0
ip router isis interface Loopback0
isis circuit-type level-2 ip address 192.168.1.5 255.255.255.255
! !
FastEthernet4/0/0 interface FastEthernet0/0
ip address 192.168.120.10 255.255.255.0 ip address 192.168.120.5 255.255.255.0
ip router isis ip router isis
isis circuit-type level-1 !
! router isis
router isis is-type level-1
passive-interface Loopback0 passive-interface Loopback0
net 49.0001.1921.6800.1001.00 net 49.0001.1921.6800.1005.00
Configuration for C&D L1L2 routers
Rtr-B Rtr-C
Area 49.0001 Area 49.0002
Router-C
interface Loopback0 Rtr-A Rtr-D
ip address 192.168.2.2 255.255.255.255 L1routers
!
Interface Pos1/0/0 Router-D
ip address 192.168.222.2 255.255.255.0
ip router isis interface Loopback0
isis circuit-type level-2 ip address 192.168.2.4 255.255.255.255
! !
interface Fddi3/0 interface Fddi6/0
ip address 192.168.111.2 255.255.255.0 ip address 192.168.111.4 255.255.255.0
ip router isis ip router isis
isis circuit-type level-1 !
! router isis
router isis is-type level-1
passive-interface Loopback0 passive-interface Loopback0
net 49.0002.1921.6800.2002.00 net 49.0002.1921.6800.2004.00
Adding interfaces to ISIS
 To activate ISIS on an interface:

interface HSSI 4/0
ip route isis isp-bb
isis circuit-type level-2
 To disable ISIS on an interface:

router isis isp-bb
passive-interface GigabitEthernet 0/0
Disables CLNS on that interface
Puts the interface subnet address into the LSDB
 No ISIS configuration on an interface

No CLNS run on interface, no interface subnet in the LSDB
Adding interfaces to ISIS
 Scaling ISIS: passive-interface default

Disables ISIS processing on all interfaces apart from those
marked as no-passive
Places all IP addresses of all connected interfaces into ISIS
Must be at least one non-passive interface:
router isis isp-bb

passive-interface default
no passive-interface GigabitEthernet 0/0
interface GigabitEthernet 0/0
ip router isis isp-bb
isis metric 1 level-2

Status Commands in ISIS
 Show clns
Shows the global CLNS status as seen on the router, e.g.
Rtr-B>show clns
Global CLNS Information:
2 Interfaces Enabled for CLNS
NET: 49.0001.1921.6800.1001.00
Configuration Timer: 60, Default Holding Timer: 300, Packet
Lifetime 64
ERPDU's requested on locally generated packets
Intermediate system operation enabled (forwarding allowed)
IS-IS level-1-2 Router:
Routing for Area: 49.0001

 Show clns neighbors
Shows the neighbour adjacencies as seen by the router:
Rtr-B> show clns neighbors

System Id SNPA Interface State Holdtime Type Protocol
1921.6800.2002 *PPP* PO2/0/0 Up 29 L2 IS-IS
1921.6800.1005 00e0.1492.2c00 Fa4/0/0 Up 9 L1 IS-IS
More recent IOSes replace system ID with router

hostname – ease of troubleshooting

 Show clns interface

Shows the CLNS status on a router interface:
Rtr-B> show clns interface POS2/0/0

POS2/0/0 is up, line protocol is up
Checksums enabled, MTU 4470, Encapsulation PPP
ERPDUs enabled, min. interval 10 msec.
RDPDUs enabled, min. interval 100 msec., Addr Mask enabled
Congestion Experienced bit set at 4 packets
DEC compatibility mode OFF for this interface
Next ESH/ISH in 47 seconds
Routing Protocol: IS-IS
Circuit Type: level-1-2
Interface number 0x0, local circuit ID 0x100
Level-1 Metric: 10, Priority: 64, Circuit ID: 1921.6800.2002.00
Number of active level-1 adjacencies: 0
Level-2 Metric: 10, Priority: 64, Circuit ID: 1921.6800.1001.00
Number of active level-2 adjacencies: 1
Next IS-IS Hello in 2 seconds

 Show CLNS protocol

Displays the status of the CLNS protocol on the router:
Rtr-B> show clns protocol

IS-IS Router: <Null Tag>
System Id: 1921.6800.1001.00 IS-Type: level-1-2
Manual area address(es):
49.0001
Routing for area address(es):
49.0001
Interfaces supported by IS-IS:
FastEthernet4/0/0 - IP
POS2/0/0 - IP
Redistributing:
static
Distance: 110
Other status commands
 “show clns traffic”

Shows CLNS traffic statistics and activity for the network
 “show isis database”

Shows the ISIS link state database
i.e. the “routing table”

Network Design Issues
 As in all IP network designs, the key issue is the

addressing lay-out
 ISIS supports a large number of routers in a single area
 When using areas, use summary-addresses
 >400 routers in the backbone is quite doable

Network Design Issues
 Possible link cost

Default on all interfaces is 10
(Compare with OSPF which sets cost according to link bandwidth)
Manually configured according to routing strategy
 Summary address cost
Equal to the best more specific cost
Plus cost to reach neighbor of best specific
 Backbone has to be contiguous
Ensure continuity by redundancy
 Area partitioning
Design so that backbone can NOT be partitioned

Scaling Issues
 Areas vs. single area

Use areas where
sub-optimal routing is not an issue
areas with one single exit point
Start with L2-only everywhere is a good choice
Future implementation of level-1 areas will be easier
Backbone continuity is ensured from start

ISIS for IPv6

IS-IS for IPv6
 2 Tag/Length/Values added to introduce IPv6 routing

 IPv6 Reachability TLV (0xEC)
External bit
Equivalent to IP Internal/External Reachability TLV’s
 IPv6 Interface Address TLV (0xE8)
For Hello PDUs, must contain the Link-Local address
For LSP, must only contain the non-Link Local address
 IPv6 NLPID (0x8E) is advertised by IPv6 enabled routers

IOS IS-IS dual IP configuration
Router1#
interface ethernet-1
ip address 10.1.1.1 255.255.255.0
ipv6 address 2001:db8:1::1/64
LAN1: 2001:db8:1::/64 ip router isis
ipv6 router isis
Ethernet-1
interface ethernet-2
Router1 ip address 10.2.1.1 255.255.255.0
Ethernet-2 ipv6 address 2001:db8:2::1/64
ip router isis
LAN2: 2001:db8:2::/64 ipv6 router isis
router isis
Dual IPv4/IPv6 configuration. address-family ipv6
redistribute static
Redistributing both IPv6 static routes exit-address-family
and IPv4 static routes. net 49.0001.0000.0000.072c.00
redistribute static

IOS Configuration for IS-IS for IPv6 on
IPv6 Tunnels over IPv4
On Router1:
interface Tunnel0
no ip address IPv6
ipv6 address 2001:db8:1::1/64 Network
ipv6 address FE80::10:7BC2:ACC9:10 link-local
ipv6 router isis
tunnel source 10.42.1.1 IPv6 Tunnel
tunnel destination 10.42.2.1
!
router isis
IPv4 IPv6
net 49.0001.0000.0000.0001.00
Backbone Tunnel
IPv6
IPv6 Tunnel
On Router2: Network
interface Tunnel0 IPv6
no ip address Network
ipv6 address FE80::10:7BC2:B280:11 link-local IS-IS for IPv6 on an IPv6 Tunnel
ipv6 router isis
tunnel source 10.42.2.1 requires GRE Tunnel; it can’t work
!
tunnel destination 10.42.1.1
with IPv6 configured tunnel as IS-IS
router isis runs directly over the data link layer
net 49.0001.0000.0000.0002.00
Multi-Topology IS-IS extensions
 IS-IS for IPv6 assumes that the IPv6 topology is the

same as the IPv4 topology
Single SPF running, multiple address families
Some networks may be like this, but many others are not
 Multi-Topology IS-IS solves this problem

New TLV attributes introduced
New Multi-Topology ID #2 for IPv6 Routing Topology
Two topologies now maintained:
ISO/IPv4 Routing Topology (MT ID #0)
IPv6 Routing Topology (MT ID #2)

Multi-Topology IS-IS extensions
 New TLVs attributes for Multi-Topology extensions:

Multi-topology TLV: contains one or more multi-topology ID in
which the router participates
MT Intermediate Systems TLV: this TLV appears as many times
as the number of topologies a node supports
Multi-Topology Reachable IPv4 Prefixes TLV: this TLV appears
as many times as the number of IPv4 announced by an IS for a
given MT ID
Multi-Topology Reachable IPv6 Prefixes TLV: this TLV appears
as many times as the number of IPv6 announced by an IS for a
given MT ID

Multi-Topology ISIS configuration
example (IOS)
Router1#
Area B interface Ethernet 1
ip address 10.1.1.1 255.255.255.0
ip router isis
ipv6 router isis
LAN1: 2001:db8:1::1/64 isis ipv6 metric 20
Ethernet 1 interface Ethernet 2

ip address 10.2.1.1 255.255.255.0
Router1 ipv6 address 2001:db8:2::1/64
Ethernet 2 ip router isis
ipv6 router isis
LAN2: 2001:db8:2::1/64 isis ipv6 metric 20
 The optional keyword transition may router isis
be used for transitioning existing IS-IS net 49.0001.0000.0000.072c.00
IPv6 single SPF mode to MT IS-IS metric-style wide
!
 Wide metric is mandated for Multi- address-family ipv6
Topology to work multi-topology
exit-address-family
Narrow to Wide Metrics Transition
 When migrating from narrow to wide metrics, care is

required
Narrow and wide metrics are NOT compatible with each other
Migration is a two stage process, using the “transition” keyword
 Networks using narrow metrics should first configure

across all routers:
router isis isp
metric-style transition
 Once the whole network is changed to transition

support, the metric style can be changed to wide:
router isis isp
metric-style wide
ISP common practices
 NSAP address construction

Area and loopback address
 L2
L1-L2 and L1 used later for scaling
 Wide metrics
Narrow metrics are too limiting
 Deploying IPv6 in addition to IPv4

Multi-topology is recommended – gives increased flexibility
should there be future differences in topology

ISP Best Practices
Extra detailed information

Purging the RIB on link failure
 For routing protocols that are capable of responding to

link failures, IOS allows such routing protocols to
quickly and more efficiently delete associated routes
from the RIB when a link, and the interface is removed
from the routing table
 Without this command, the "less efficient" RIB process
is used to delete the associated next-hop routes of the
failed interface, by default
If this process has to work through a very large routing table, it
can use up a number of CPU cycles and potentially increase
convergence time.
ip routing protocol purge interface

ISIS neighbour authentication
 Create key chains to be used for HMAC-MD5

authentication for both Level-1 and Level-2
key chain isis-sec-l1

key 1
key-string xxxxx
key chain isis-sec-l2
key 1
key-string xxxxx

Setting up Loopback Interface
 Create the Loopback interface/Router-ID

It will NOT have IS-IS running on it because it is not a transit
interface
Disabling IS-IS on it, while announcing the IP prefixes into IS-
IS, allows the IS-IS domain to scale because LSP/Hello packets
are not unnecessarily generated for the Loopback interface
An IS-IS metric will NOT be set, which will default the Loopback
interface's metric to zero (0).
interface loopback0
ip address 192.168.0.1 255.255.255.255
ipv6 address 2001:db8:192:168:0:1/128

Level-1 Interface Configuration
 Configure addresses and enable ISIS for IPv4 and IPv6

interface gigabitethernet0/1
ip address 192.168.1.1 255.255.255.192
ipv6 address 2001:db8:192:168:1:1/112
!
ip router isis 1
ipv6 router isis 1
 Ensure this interfaces runs at Level-1

isis circuit-type level-1

Level-1 Interface: Metrics & Auth
 Set the costs for IPv4 and IPv6

isis ipv6 metric 400 level-1
 Enable HMAC-MD5 for level-1

isis authentication mode md5 level-1
 Associate the key-chain defined earlier

isis authentication key-chain isis-sec-l1 level-1

Level-1 Interface: DIS and BFD
 Set this IS to be the DIS in this Level-1 area

A DIS of 126 (higher than the default of 64) configured on
another IS in this area sets it up as the backup DIS
isis priority 127 level-1
 Enable BFD for fast failure detection

BFD helps reduce the convergence times of IS-IS because link
failures will be signalled much quicker
bfd interval 250 min_rx 250 multiplier 3

Level-2 interface
 This interface is used for a trunk link to another PoP forming part of
your network-wide backbone
As such it will be a Level-2 interface, making this router a Level-
1/Level-2 IS.
Metric and authentication are all configured for Level-2
ip address 192.168.2.1 255.255.255.252
ipv6 address 2001:db8:192:168:2:1:/126
ip router isis 1
ipv6 router isis 1
isis circuit-type level-2-only
isis ipv6 metric 400 level-2
isis authentication mode md5 level-2
isis authentication key-chain isis-sec-l2 level-2
Level 2 interface: more details
 To make this IS-IS BCP more interesting, we will assume this trunk
link is a broadcast multi-access link, i.e., Ethernet.
 As this is an Ethernet interface, IS-IS will attempt to elect a DIS
when it forms an adjacency
Because it is running as a point-to-point WAN link, with only 2 IS's on
the wire, configuring IS-IS to operate in "point-to-point mode" scales
the protocol by reducing the link failure detection times
Point-to-point mode improves convergence times on Ethernet networks
because it:
Prevents the election of a DIS on the wire,
Prevents the flooding process from using CSNP's for database
synchronization
Simplifies the SPF computations and reduces the IS's memory
footprint due to a smaller topology database.
int gi0/2
isis network point-to-point
ISP Best Practices
 We now configure parameters specific to the IS-IS routing protocol

This covers both IPv4 and IPv6, as IS-IS supports both IP protocols in
the same implementation
router isis 1
 Create an NET
This is made up of a private AFI (49), an area part, a System ID (taken
from the padded Loopback interface IP address) and an N-SEL of zero
(0).
net 49.0001.1921.6800.0001.00
 Enable HMAC-MD5 authentication

authentication mode md5
authentication key-chain isis-sec-l1 level-1
authentication key-chain isis-sec-l2 level-2
ISP Best Practices
 Enable iSPF (incremental SPF).

This, in the long run, reduces CPU demand because SPF calculations
are run only on the affected changes in the SPT.
As this is a Level-1/Level-2 router, enable iSPF at both levels 60
seconds after the command has been entered into the configuration.
Note that IOS only supports iSPF for IPv4.
ispf level-1-2 60
 Enable wide/extended metric support for IS-IS.

IOS, by default, supports narrow metrics, which means you can define
cost values between 1-63. This is not scalable.
To solve this problem, enable wide metrics, which allows you to define
cost values between 1-16777214.
metric-style wide

ISP Best Practices
 Increase ISIS default metric

Default value is 10
All interfaces in both L1 and L2 have this value
Not useful if configured value is “accidentally” removed - a low priority
interface could end up taking full load by mistake
Configure a “very large” value as default
metric 100000
 Disable IIH padding because on high speed links, it may strain

huge buffers; and on low speed links, it may waste bandwidth and
affect other time sensitive applications, e.g., voice.
Disabling IIH padding is safe because IOS will still pad the first 5 IIH's
to the full MTU to aid in the discovery of MTU mismatches.
no hello padding

ISP Best Practices
 Allow the Loopback interface IP address to be carried within IS-IS,

while preventing it from being considered in the flooding process.
passive-interface Loopback0
 Log changes in the state of the adjacencies.

log-adjacency-changes
 Tell the IS to ignore LSP's with an incorrect data-link checksum,

rather than purge them
Purging LSP's with a bad checksum causes the initiating IS to
regenerate that LSP, which could overload the IS if perpetuated in a
cycle
So rather than purge them, ignore them.
ignore-lsp-errors

ISP Best Practices
 Reduce the amount of control traffic, conserving CPU usage for

generation and refreshing of LSP's.
Do this by increasing the LSP lifetime to its limits.
max-lsp-lifetime 65535
 Reduce the frequency of periodic LSP flooding of the topology,

which reduces link utilization
This is safe because there other mechanisms to guard against
persistence of corrupted LSP's in the LSDB.
lsp-refresh-interval 65000
 Customize IS-IS throttling of SPF calculations.

Good for when you also use BFD for IS-IS.
These are recommended values for fast convergence.
spf-interval 5 1 20
ISP Best Practices
 Customize IS-IS throttling of PRC calculations.

PRC calculates routes without performing a full SFP calculation.
This is done when a change is signaled by another IS, but without a
corresponding change in the basic network topology, e.g., the need to
reinstall a route in the IS-IS RIB.
prc-interval 5 1 20
 Customize IS-IS throttling of LSP generation.

lsp-gen-interval 5 1 20

ISP Best Practices
 Enable IS-IS fast-flooding of LSP's.

This tells the IS to always flood the LSP that triggered an SPF before
the router actually runs the SPF computation.
This command used to be 'ip fast-convergence' and has since been
replaced from IOS 12.3(7)T.
Below, we shall tell the IS to flood the first 10 LSP's which invoke the
SPF before the SPF computation is started
fast-flood 10
 Enable IS-IS IETF Graceful Restart.

This ensures an IS going through a control plane switchover continues
to forward traffic as if nothing happened
Software and platform support is limited, so check whether your
particular platform/code supports this
Also, deploy only if it's necessary.
nsf ietf
ISP Best Practices
 Enable BFD support for IS-IS.

With BFD running on the interface, a failure of the link would signal IS-
IS immediately
IS-IS will then converge accordingly.
bfd all-interfaces
 Tell IS-IS to ignore the attached bit

The Attached bit is set when an L1/L2 IS learns L1 routes from other
L1 routers in the same area
The Attached bit causes the installation of an IS-IS-learned default
route in the IS-IS RIB on L1 routers in the same area, as well as in the
forwarding table if IS-IS is the best routing protocol from which the
default route was learned – this can lead to suboptimal routing.
ignore-attached-bit

ISP Best Practices
 Wait until iBGP is running before providing transit path

set-overload-bit on-startup wait-for-bgp
Avoids blackholing traffic on router restart
Causes ISIS to announce its prefixes with highest possible
metric until iBGP is up and running
When iBGP is running, ISIS metrics return to normal, make the
path valid
 Enable the IPv6 address family for in IS-IS.
address-family ipv6
 Enable multi-topology support for IPv6 in IS-IS.

Multi-topology support allows the IPv4 topology to be
independent of that of IPv6
multi-topology

ISP Best Practices
 Things to consider on routers operating as Level-1-only

IS's:
IS-IS BCP techniques under the IS-IS routing process
In addition to the interface, tell the IS-IS routing process to
operate in a Level-1 area only
router isis 1
is-type level-1

ISP Best Practices
 Things to consider on routers operating as Level-1 and Level-2 IS’s:

To prevent sub-optimal routing of traffic from L1 IS's in one area to L1 IS's in
another area, configure and enable Route Leaking on L1/L2 routers that
form the backbone connectivity between two or more different areas
Route Leaking permits L1/L2 routers to install L1 routes learned from one
area into L1 IS’s routing/forwarding tables in another area
This allows for reachability between L1 routers located behind L1/L2 routers
in different areas
router isis 1
redistribute isis ip level-2 into level-1 route-map FOO
!
ip prefix-list foo permit 0.0.0.0/0 le 32
!
route-map FOO permit 10
match ip address prefix-list foo
ISP Best Practices
 Doing the same for IPv6:
router isis 1
address-family ipv6
redistribute isis level-2 into level-1 route-map FOO6
!
ip prefix-list foo6 permit 0.0.0.0/0 le 32
!
route-map FOO6 permit 10
match ip address prefix-list foo6
!

ISP Best Practices
 Summary
Best practice recommendations are commonly implemented on
many ISP backbones
Ensures efficient and scalable operation of ISIS

Introduction to ISIS
Philip Smith [email protected]

MENOG 4
5th-9th April 2009
Bahrain

Isis

Uploaded by

Copyright:

Available Formats

Isis

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Isis

Uploaded by

Copyright:

Available Formats

ISIS Tutorial

Philip Smith <[email protected]>

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 1

 Feel free to ask questions any time

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 2

 Comparing ISIS and OSPF

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 3

Both Link State Protocols use the Dijkstra SPF

So what’s the difference then??

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 4

 Intermediate System to Intermediate System

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 5

 1978ish “New” Arpanet Algorithm

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 6

 Open Shortest Path First

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 7

 Development began in 1987 by IETF

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 8

 Both are Interior Gateway Protocols (IGP)

 With support for:

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 9

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 10

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 11

 OSPF uses IP Protocol 89 as transport

Data Link Header IP Header OSPF Header OSPF Data

 IS-IS is directly encapsulated in Layer 2

Data Link Header IS-IS Header IS-IS Data

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 12

 Which IGP should an ISP choose?

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 13

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 14

 ISIS runs on link layer

 ISIS’s NSAP addressing scheme avoids dependencies

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 15

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 16

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 17

 ISIS has a 2 layer hierarchy

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 18

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 19

 ISIS does not have a backbone area as such (like

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 20

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 21

 NSAP: Network Service Access Point

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 22

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 23

 ISPs typically choose NSAP addresses thus:

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 24

 Hello PDU IIHs are exchanged between routers to form

ISIS adjacency through IIH

 Area addresses are exchanged in IIH PDUs

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 25

 Each router creates an LSP and flood it to neighbours

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 26

 LSPs have  The LSP header contains

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 27

 The LSP contents are coded as TLV (Type, Length,

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 28

 Each router maintains a separate LSDB for level-1 and

MENOG 4 © 2009 Cisco Systems, Inc. All rights reserved. 29

 New LSPs are flooded to all neighbors