Cross Section X-X Cross Section Y-Y: Decg International

Download as pdf or txt
Download as pdf or txt
You are on page 1of 1

DESIGN PARAMETER-ULS

LOAD CAPACITY (IN KN) MOVEMENT ROTATION


HORIZONTAL (Hmax) (IN mm) (IN rad.)
1115 mm TOP CONCRETE EMBEDMENT PLATE
LONG. TRANS.
Ø 1090 mm TOP FLANGE O/O
970 mm PCD 1115 mm TOP CONCRETE EMBEDMENT PLATE
NORMAL 5600 2200
Ø1090 mm OF TOP PLATE LONG. = 0
Ø720 mm PIN 0.015
4
Ø 498 mm PISTON INSIDE POT 970 mm PCD TRANS.= 0
3
DETAIL-'A' SEISMIC Max. - -

TOP CONCRETE EMBEDMENT GRADE OF MATERIAL AT TOP (GIRDER) = E250


PLATE OF 1115X1115 X 45
26 Nos. OF BOLTS GRADE OF MATERIAL AT BOTTOM (PEDESTAL) = M40
360 mm M36 X 150 Gr.8.8 @TOP
TOTAL HEIGHT 7
8 52 WASHER STEEL IRC:83 (PART-III)
26 Nos. OF BOLTS
M36 X 110 Gr.8.8 @BOTTOM
7 52 BOLTS M36 Gr. 8.8 IS:1367
2 BOTTOM CONCRETE EMBEDMENT
PLATE OF 1115X1115 X 45 6 81 SHEAR HEADED STUDS forged steel 4.6 class ISO 13918
1

5 1 NON PRESSURE PAD NATURAL RUBBER IRC:83 (PART-III)

CONCRETE EMBEDMENT
40 Nos. SHEAR HEADED STUDS 24 Ø X 216 Lg. 4 1 MILD STEEL IS:2062 E350
PLATE TOP
41 Nos. SHEAR HEADED STUDS 24 Ø X 144 Lg.
Ø 720 mm CYLINDER WALL O/O 3 1 TOP PISTON CAST STEEL IS:1030-Gr:340 - 570 W
960 mm STUDS C/C
970 mm PCD 970 mm PCD
2 1 POT (CYLINDER) CAST STEEL IS:1030-Gr:340 - 570 W
Ø 1090 mm BOTTOM FLANGE O/O 1060 mm STUDS C/C
1115 mm BOTTOM CONCRETE EMBEDMENT PLATE CONCRETE EMBEDMENT
Ø 1090 mm OF BOTTOM PLATE 1 1 MILD STEEL IS:2062 E350
PLATE BOTTOM

CROSS SECTION X-X 26+26 Nos. OF BOLTS


1115 mm BOTTOM CONCRETE EMBEDMENT PLATE
S. NO. QTY. DESCRIPTION MATERIAL SPECIFICATION
DRILL Ø39 FOR
M36 Gr.8.8 CROSS SECTION Y-Y
@TOP & BOTTOM MATERIAL DESCRIPTION PER BEARING
Y
NOTE -
120 120 120 120 120 120 120 120 1. THIS DESIGN & DRAWING IS THE SOLE PROPERTY OF DECG
INTERNATIONAL. IT SHOULD NOT BE COPIED OR
COMMUNICATED TO ANY PERSON WITHOUT THE WRITTEN
APPROVAL OF PROPRIETORS.
2. ALL DIMENSION ARE IN MM.
170

3. DESIGN AS PER IRC:83-2018 (PART-III).


4. ALL MANUFACTURING SHOULD BE CONFIRM AS PER IRC
SPECIFICATION.

Ø 60 mm
120

1115 mm TOP/BOTTOM CONCRETE EMBEDMENT PLATE

10 mm

STUD IS WELDED TO THE


120

TOP & BOTTOM PLATE BY


DRILLING A COUNTER SUNK 3
X X OF 5 mm DEEP
2
Ø 24
120

1 09-03-2024 0 INITIAL SUBMISSION J.T. A.K.S.


970 mm PCD

S. NO. DATE Rev. No. DESCRIPTION DRAWN CHECKED


120

TYPE - PIN BEARING TOTAL QTY.


10 mm THICK. WELD
SPAN - 36 M
120

02 Nos.
34
TITLE GAD FOR PIN BEARING (DMPB - 560 T)
120

44
PROJECT MUGALSARAI-GAYA SECTION ON VILLAGE ROAD.
WELDING DETAIL OF STUD CHITTORPUR
(FORGED STEEL)
170

CLIENT DEDICATED FREIGHT CORRIDOR CORPORATION OF INDIA LTD.


CONTRACTOR JCL INFRA PVT LTD
CONSULTANT -
45 mm
Y DRAWING NO. DECG/JCL/BH/2024/03/2021319
1115 mm TOP/BOTTOM CONCRETE EMBEDMENT PLATE 98 mm THIK. DATE 09-03-2024 DRAWN J.T.

14 SHEET N0. 07 of 10 SCALE CHECKED P.K.


PLAN 80 24
REV. R0 N.T.S. APPROVED A.K.S.
34 mm R650 110 mm 100 mm
TRANSVERSE DIRECTION

MANUFACTURER / DESIGNER
58 mm FLANGE MANUFACTURER / DESIGNER

58 mm
45 mm DECG INTERNATIONAL
OF BRIDGE

Ø 500 mm X 34 mm
Crop. office: 69C, Sector A, Bhopal-Hoshamgabad Road (NH46)
NON PRESSURE PAD 5 Mandideep, Raisen- 462 046 , Madhya Pradesh
DETAIL-A Telephone : 9109120039, 9811350648
TRAFFIC DIRECTION
E-mail : [email protected], [email protected]
OF BRIDGE
Website : www.decgintl.com

You might also like