Bc-Prime SF

Download as pdf or txt
Download as pdf or txt
You are on page 1of 2

Your Perfect Flooring Solutions

BC-PRIME SF
A SOLVENT FREE TWO PART EPOXY PRIMER

DESCRIPTION: BENEFITS:
BC-Prime SF is a two - component solvent free epoxy primer  Compatible with wide range of topcoats.
with low viscosity, excellent penetrating properties even into  Low odor during application.
damp concrete substrate.  Damp tolerant
 Deep penetrating into concrete substrate to avoid peeling
PRODUCT FEATURE:
BC-Prime SF is recommended as a primer for concrete surface
prior to application of concrete substrate, membranes, mortar
COLORS:
 Clear
or topping. BC-Prime SF also can be use in workshops,
warehouses and mechanical rooms to prevent dusting. Exhibit
excellent adhesions between mortar and the concrete substrate.

TECHNICAL DATA
Density ( 28°C ) g/ml (mixed) 1.00±0.05 g/ml
Viscosity (28°C) (mixed) 800±200 cps
Adhesive strength >2.0MPa
(concrete failure)
Number of Coats 1 or 2
Recommended D.F.T. per coat 100(+/-)5µ
Cleaner BC-washing thinner
Mixing Ratio by Weight Part A : Part B
4 : 1
Pot life (working time) 28⁰C 40min
Packing Size 5kg & 20kg & 200kg
Shelf life & storage 24 months
(unopened and in good conditions
temperature 5⁰C to 30⁰C)
Material consumption 0.2 kg/m²
Drying time 6-8 hours
Foot traffic (Good Ventilation) 24 hours
Your Perfect Flooring Solutions

BC-PRIME SF
A SOLVENT FREE TWO PART EPOXY PRIMER

SUBSTRATE REQUIREMENT & PREPARATION: Maintenance and care after cure :


 Substrate concrete or screed should be a minimum of We recommend basic cleaning and maintenance will prolong
compressive strength 25N/mm² and adhesive pull-off the life of epoxy floors, clean regularly using a single or double
strength of minimum 1.5N/mm² ( concrete failure ) headed rotary scrubber drier in conjunction with alkaline
 Concrete substrates must be prepared mechanically using detergent.
abrasive blast cleaning or scarifying equipment to remove
cement laitance and achieve an open textured surface. Further Information:
 Crack and hollows should be properly remedied. Warning and precautions information relating to the safe
 Rough contaminations and high spots can be removed by handling of this product should be found in Material Safety
grinding. Data Sheet. To be advise to put on suitable clothing and eye-
 The substrate should be clean and free from laitance, oil, ware for protection purpose. The application area/site must be
dust, paint residues, algae, loose and friable material must in good ventilation otherwise advisable to use a portable
be completely removed from all surfaces before application exhaust fan.
of the product.
Important Note :
MIXING: Best Crete product are warranty against defective materials.
Pour total Part B into the Part A container and mix both liquid Due to different substrate and working conditions, no guarantee
part thoroughly for one minute by using a suitable electrical of an application result or any liability claims. The users are
stirrer (with 750 watt high power mixer) until a fully required to have a test ahead based on their intended use.
homogenous mix has been achieved.

APPLICATION:
 Apply BC-Prime SF can be use by suitable roller, brush or
trowel and overwork with a roller.
 BC-Prime SF should apply within the pot life 45 minutes at
28ᵒC
 Substrate temperature should not apply 5ᵒC above the dew
point.

CLEANING OF TOOLS:
Clean all the tools and application equipment with BC-
Washing thinner before the product hardens.

BEST CRETE (M) SDN BHD (969553-A) (GST/BCP NO: 001222787072),


NO.1, JALAN PERUSAHAAN 21/KS5, KAWASAN PERINDUSTRIAN KAMPUNG IDAMAN, 42000 PELABUHAN KLANG, SELANGOR DARUL EHSAN, MALAYSIA,
TEL: +603-3167 1263, +603-3168 1263, +603-3162 5044 FAX: +603-3166 2263,
EMAIL: [email protected] WEBSITE: www.bestcretepolymers.com

You might also like