Connecting to the

Aspila EX

Installing PCPro

Local Connection

Creating a Dial Up
Setting for Remote
Access
USB Connection for
Local Access

Serial Connection for

Local Access

Using PCPro

Using WebPro

PCPro/WebPro
Installation Manual
991092-5
1.2
(AP : February 2004)
This manual has been developed by NEC Infrontia Asia Pacific Sdn Bhd. It is intended for the use of its customers
and service personnel, and should be read in its entirety before attempting to install or program the system. Any
comments or suggestions for improving this manual would be appreciated. Forward your remarks to:

NEC Infrontia Assia Pacific Sdn Bhd

Lot 24, Jalan Juruhebah U1/50
Temasya Industrial Park Phase 2, Seksyen U1,
Glenmarie, 40150 Shah Alam, Selangor Darul Ehsan.

[email protected]

www.necinfrontia-ap.com

Nothing contained in this manual shall be deemed to be, and this manual does not constitute, a warranty of, or
representation with respect to, any of the equipment covered. This manual is subject to change without notice and
NEC Infrontia has no obligation to provide any updates or corrections to this manual. Further, NEC Infrontia also
reserves the right, without prior notice, to make changes in equipment design or components as it deems
appropriate. No representation is made that this manual is complete or accurate in all respects and NEC Infrontia
shall not be liable for any errors or omissions. In no event shall NEC Infrontia be liable for any incidental or
consequential damages in connection with the use of this manual. This document contains proprietary information
that is protected by copyright. All rights are reserved. No part of this document may be photocopied or reproduced
without prior written consent of NEC Infrontia

©2003 by NEC Infrontia Asia Pacific Sdn Bhd

Document History
Revision 1.0 May 2003
First Release

Revision 1.1 October 2003

Add confirmation of Aspire software level to Connecting to the Aspila EX section

Revision 1.2 November 2003

Add Local USB connection.
Add Local Serial connection.

Aspila EX PCPro/WebPro Installation Manual - 3

 - Blank Page -

Aspila EX PCPro/WebPro Installation Manual - 4

 Table of Contents
Table of Contents

Connecting to the Aspila EX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Ethernet Connection for Local Access: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
USB Connection for Local Access: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Serial Connection for Local Access: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Connection for Remote Access: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing PCPro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Local LAN (Ethernet) Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Creating a Dial Up Setting for Remote Access . . . . . . . . . . . . . . . . . 11
USB Connection for Local Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Creating a Dial Up Connection for Local Access via a USB Port. . . . . . . . . . . . 18
Serial Connection for Local Access. . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Creating a Dial Up Connection for Local Access via a Serial Port. . . . . . . . . . . 19
Using PCPro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Common Buttons within PCPro and WebPro . . . . . . . . . . . . . . . . . . 25
Using WebPro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Table of Contents 1
Table of Contents

2 Table of Contents
 Connecting to the Aspila EX
Connecting to the Aspila EX

Connecting to the Aspila EX

In addition to the system phone programming, the Aspila EX system provides the ability to use a PC to access system pro-
gramming. The Windows-based PCPro and the HTML-based WebPro allows you to:
• Edit the telephone system programming options from a remote location.
The PCPro application requires changes to be uploaded to the system before they take effect. The WebPro
application applies the changes as soon as the APPLY or OK icon is clicked.
• Access system maintenance functions (like reports and tests).

In addition, PCPro allows you to:

• Save your programming to your PC’s hard disk - then upload it via a LAN (Local Area Network), PPP, serial or
USB connection.
PPP is a protocol that allows a computer to use a regular telephone line and a serial interface (modem) to
make TCP/IP connections.
• Download the existing programming in the telephone system via a LAN, PPP, serial or USB connection - and
save it to your PC’s hard disk.
• Setup a default database with the settings you use most often.
• Create a unique database for each phone system you have installed. Since you save the site-specific data to your
PC’s hard disk, you can easily retrieve a customer’s programming if something goes wrong.

PCPro PC Requirements
• CPU: Pentium II 500 MHz equivalent or higher
• 128Mb of RAM
• 20Mb of Hard Drive Space
• Monitor Resolution: 800 x 600 pixels or higher
• Mouse
• Microsoft Windows 2000/XP
• Internet Browser: Internet Explorer 6.0 or higher or Netscape 6.0 or higher
• Network Interface Card (NIC) (depending on connection type)

WebPro PC Requirements
• CPU: Pentium III 600 MHz equivalent or higher
• Monitor Resolution: 800 x 600 pixels or higher
• Mouse
• Microsoft Windows 2000/XP
• Internet Browser: Internet Explorer 6.0 or higher or
Netscape 6.0 or higher
• Network Interface Card (NIC) (depending on connection type)

The browser settings should allow all Cookies and have Scripting/Active Scripting enabled.
Internet Explorer: Click Tools-Internet Options-Security-Internet or Local Intranet (depending on your connec-
tion)-Custom Level. Set Allow Cookies That Are Stored On Your Computer and Allow Per-Session Cookies (Not
Stored) to “Enable”. Set Active Scripting to “Enable”.
Netscape: Click Edit-Preferences. Under Privacy & Security, set Cookies to “Enable All Cookies”. Under Advanced-
Scripts & Plugins the checkbox for Enable JavaScript for Navigator should be checked.

Aspila Ex PCPro/WebPro Installation Manual 1

Connecting to the Aspila EX
The following changes must be made in order to connect to the Aspila EX system.

With the Aspila EX set at default (Program 10-12-01 = IP Address 172.16.0.10 and Program 10-13-01 = 0 [DHCP Server dis-
abled]):
1. The network settings on the PC connecting to the Aspila EX system must be changed. Set the IP address to 172.16.0.11
(172.16.0.12, 172.16.0.13, etc would also be acceptable) and change the subnet mask to 255.255.0.0.

With the Aspila EX set to use the built-in DHCP Server (Program 10-12-01 = IP Address 172.16.0.10 and Program 10-13-
01 = 1 [DHCP Server enabled]):
1. The network settings on the PC connecting to the Aspila EX system must be set to obtain an IP address automatically.

The location of the IP setting depends on the Windows version being used, but for example, with Windows
XP you would access these settings by clicking:
START-SETTINGS-NETWORK CONNECTIONS-Right mouse click on LOCAL AREA CONNECTION-
Select PROPERTIES-Click on INTERNET PROTOCOL (TCP/IP)-Click PROPERTIES-Select the GENERAL tab
if not already selected.

Connecting to the Aspila EX System

In order to use either PCPro or WebPro, the Aspila EX system must be connected to the PC in one of the ways shown below.
For local connection you can connect via Ethernet either through a hub or with a cross-over cable connected directly to the
system, a USB cable or a serial cable. Refer to Section 6: LAN Connection in the Aspila EX Hardware Manual or the Aspila
EX IP Manual for more details on LANs and assigning IP addresses.
For remote connection you can connect your PC to an ISDN Terminal Adapter and make a dial up connection to the Aspila
EX.

Ethernet Connection for Local Access:

For local connection you can connect from the PC to the Aspila EX using the LAN port on the NTCPU.
You can connect directly into the Ethernet socket (CN15) on the NTCPU or via the LAN, if the NTCPU is
already connected to the LAN.

2 Aspila Ex PCPro/WebPro Installation Manual

 Connecting to the Aspila EX
LAN Cable
Straight through RJ45 patch cable.

Pin Pin
1 1
2 2
3 3
6 6

LAN Cross Cable

RJ45 cable with cross over Tx and Rx.

Pin Pin
1 3
2 6
3 1
6 2

USB Connection for Local Access:

For local connection you can connect from the PC to the Aspila EX using the USB port on the NTCPU.

USB Cable Type-A to Type-B is required.

Aspila Ex PCPro/WebPro Installation Manual 3

Connecting to the Aspila EX
Serial Connection for Local Access:
For local connection you can connect from the PC to the Aspila EX using the Serial port on the NTCPU.

The serial cable is null modem with a 9-pin male connector on the NTCPU.
The connections for a 9 way female to 9 way female cable are shown below (DXE cable part number NKUK-034 can be used).

Pin Pin
1 7&8
2 3
3 2
4 6
5 5
6 4
7&8 1

4 Aspila Ex PCPro/WebPro Installation Manual

 Connecting to the Aspila EX
Connection for Remote Access:
For remote connection you can connect from the PC to the Aspila EX using an ISDN Terminal Adapter and ISDN trunk.

Remote Access via ISDN Trunk

The connection to the remote Aspila EX system is made via an ISDN Terminal Adaptor with a dial up connection using PPP
(Point to Point Protocol).
The incoming DDI at the Aspila EX is routed to Service Code 830 in Program 22-11, (830 is the default ‘Remote Mainte-
nance’ service code set in Program 11-15-01). Refer to Creating a Dial Up Setting for Remote Access (page 11).

Confirming the Aspila EX Software Level.

If you are not certain of the software level of the Aspila EX system that you are connecting to then download only program 90-
16. This program can be found in the System Data drop down list within the Dowload menu. When you have dowloaded pro-
gram 90-16 the software level of the Aspila EX can be confirmed within the System Data Programming list.

Aspila Ex PCPro/WebPro Installation Manual 5

Installing PCPro
Installing PCPro

Installing PCPro
To install the PC Program on your hard disk:
1. Insert the PC Program Installation disk into your PC.
2. From MY COMPUTER, double-click on the drive.
3. Double-click on the SETUP.EXE file. You see:

4. Click NEXT.

5. Click on the checkbox to accept the license terms. The following window displays:

6 Aspila Ex PCPro/WebPro Installation Manual

 Installing PCPro
6. Change the installation directory if required, then click NEXT.

7. Change the shortcut name if required, then click NEXT.

8. Click FINISH to begin the installation. The following message is displayed:

Aspila Ex PCPro/WebPro Installation Manual 7

Installing PCPro
9. Click NEXT. Once the installation process has completed, the following window appears. Click FINISH.

8 Aspila Ex PCPro/WebPro Installation Manual

 Local LAN (Ethernet) Connection
Local LAN (Ethernet) Connection

Local LAN (Ethernet) Connection

When connection to the Aspila EX system is made using WebPro or PCPro via a LAN connection, an IP address and the sub-
net type must be assigned to the PC. The IP address and subnet mask are determined by the Aspila EX system in Programs 10-
12-01 and 10-12-02.
If the PC is already connected to a network and you are connecting to the NTCPU through a hub or router,
please check with your network manager to determine the IP address that should be used.

The following information is based on a stand-alone PC connected to the Aspila EX, with the Aspila EX using the default set-
tings for the IP address and subnet mask (Program 10-12-01: IP Address 172.16.0.10 / Program 10-12-02: Subnet Mask
255.255.0.0).

1. To change the TCP/IP information OF YOUR PC, click START + SETTINGS + NETWORK CONNECTIONS. The fol-
lowing window appears.

2. Right-click on the LOCAL AREA CONNECTION icon and click on PROPERTIES.

3. In the list of items, click on the INTERNET PROTOCOL (TCP/IP) and then click on PROPERTIES.

Aspila Ex PCPro/WebPro Installation Manual 9

Local LAN (Ethernet) Connection
4. In the Internet Protocol (TCP/IP) Properties window that appears, click on USE THE FOLLOWING IP ADDRESS button
and enter the following:
IP Address: 172.16.0.11 (172.16.0.12, 172.16.0.13 etc would also be acceptable)
Subnet Mask: 255.255.0.0

5. Click OK and close the INTERNET PROTOCOL window.

6. Click OK and close the LOCAL AREA CONNECTION PROPERTIES window.
7. Close the NETWORK CONNECTIONS window.

10 Aspila Ex PCPro/WebPro Installation Manual

 Creating a Dial Up Setting for Remote Access
Creating a Dial Up Setting for Remote Access

Creating a Dial Up Setting for Remote Access

When connecting from a remote location via an ISDN terminal adapter, a Dial Up Setting needs to be created on your PC with
which you can use PCPro or WebPro to access the Aspila EX system. These steps are not required when using a Local LAN
connection.

1. Click START + SETTINGS + NETWORK CONNECTIONS. The following window appears.

2. Click on CREATE A NEW CONNECTION. Click NEXT.

Aspila Ex PCPro/WebPro Installation Manual 11

Creating a Dial Up Setting for Remote Access
3. In the NETWORK CONNECTION TYPE window, select CONNECT TO THE NETWORK AT MY WORKPLACE and
click NEXT.

4. The DIAL-UP CONNECTION bullet should be selected. Click NEXT.

5. Enter the name to be used for the dial-up connection and click NEXT.

6. Enter the phone number to be dialed and click NEXT.

12 Aspila Ex PCPro/WebPro Installation Manual

 Creating a Dial Up Setting for Remote Access
• With an ISDN Terminal Adapter connection, this should be the ISDN DDI number which is routed to the
Aspila EX system. The DDI number is routed to 830 in Program 22-11-02. (830 is the ‘Remote Maintenance’
service code assigned in program 11-15-01. By default this is set to 830. If this is changed then the target in Pro-
gram 22-11-02 must be changed accordingly).

Aspila Ex PCPro/WebPro Installation Manual 13

Creating a Dial Up Setting for Remote Access
7. Enter the Aspila EX User Name and Password to be used for most sessions. Click in the box SAVE THIS USE NAME
AND PASSWORD. This will allow these settings to be used when connecting to the Aspila EX. The table below shows
the default Aspila EX user name and password settings. These can be redefined in Program 90-02.
User Name Password
ASPIRE 12345678 (Installer Level)
ADMIN1 0000 (SA Level)
ADMIN2 9999 (SB Level)

These passwords can be changed or additional passwords added after accessing programming using Pro-
gram 90-02.
With WebPro, to change or add passwords once connected to the system, click PCPRO SETTINGS, then
clicking ACCOUNT SETUP.

8. Click on PROPERTIES. In the PROPERTIES window that appears, select the SECURITY tab.

9. Select the ADVANCED (CUSTOM SETTINGS) button, then click on SETTINGS.

10. In the ADVANCED SECURITY SETTINGS window, make the following changes and then click OK.
• Data Encryption: Set to “No Encryption Allowed”
• Logon Security: Should not be checked

14 Aspila Ex PCPro/WebPro Installation Manual

 Creating a Dial Up Setting for Remote Access
• Allow These Protocols: Check “Unencrypted Password (PAP)” - all others should be unchecked.

11. Click OK.

12. Click DIAL. The system will dial the programmed number and connect to the Aspila EX system. You can now open the
PCPro application (See Using PCPro (page 24) or WebPro (See Using WebPro (page 26) for more information.

When you have created the dial up connection you can establish the call at any other time by clicking START + SETTINGS +
NETWORK CONNECTIONS and selecting the dial up connection by its name that you entered in step 5 above.

Aspila Ex PCPro/WebPro Installation Manual 15

USB Connection for Local Access
USB Connection for Local Access

USB Connection for Local Access

When the USB port is used to connect to the Aspila EX system, an NEC USB(NTCPU) driver must be installed on your PC.
Use the steps below to install the USB driver. The NTCPU USB Driver is available from the Aspila EX Technical CD.
Once the driver is installed you must create a dial up connection to enable PCPro or WebPro to connect to the Aspila EX.

The graphics shown below are with Windows XP. When using Windows 2000, there may be some differences.

1. Insert the disk containing the NEC USB driver into your PC.
2. Connect the Aspila EX system to the PC using a USB cable.
3. Windows notifies you of new hardware found. Open the Hardware Wizard window to begin the setup.

4. The software locates the USB driver file on the disk and begins the installation.
Depending on your software, the next screen may ask you to check which drives should be searched for the
USB driver.
5. When the following window appears, click CONTINUE ANYWAY.

16 Aspila Ex PCPro/WebPro Installation Manual

 USB Connection for Local Access
6. The software continues the installation process.

7. Once the software is installed, click FINISH.

8. The PC must then be restarted in order for the USB port to work.

Aspila Ex PCPro/WebPro Installation Manual 17

USB Connection for Local Access
9. Once the computer has been rebooted, right-click on MY COMPUTER and click PROPERTIES and then the HARD-
WARE tab.

10. Click on the DEVICE MANAGER button. The following screen displays listing the installed hardware.

11. Click on MODEM. If the installation was successful , the NECI USB MODEM will be listed.
If the NECI USB Modem is not listed, repeat the installation process.

Creating a Dial Up Connection for Local Access via a USB Port.

Follow the instructions for Creating a Dial Up Setting for Remote Access (page 11), at step 6 enter 830 as the Phone Num-
ber to dial, 830 is the Remote Maintenance service code assigned in Program 11-15-01.

18 Aspila Ex PCPro/WebPro Installation Manual

 Serial Connection for Local Access
Serial Connection for Local Access

Serial Connection for Local Access

When a connection is made to the Aspila EX system using the Serial port a dial up connection must be made via the COM port
of the PC.

1. Set the SW3 switch number 1 on the Aspila EX NTCPU to OFF (down). When set to ON the Serial port is set to debug
mode and will not work for PCPro or WebPro.

Creating a Dial Up Connection for Local Access via a Serial Port.

Follow steps 1 & 2 for Creating a Dial Up Setting for Remote Access (page 11), at step 3 use the following instructions.

3. In the NETWORK CONNECTION TYPE window, select SETUP AN ADVANCED CONNECTION and click NEXT.

Aspila Ex PCPro/WebPro Installation Manual 19

Serial Connection for Local Access
4. At the ADVANCED CONNECTION OPTIONS select CONNECT DIRECTLY TO ANOTHER COMPUTER and click
NEXT.

5. At the HOST or GUEST screen select GUEST and click NEXT.

20 Aspila Ex PCPro/WebPro Installation Manual

 Serial Connection for Local Access
6. At the CONNECTION NAME screen enter the name to be used for the dial up connection.

7. At the SELECT A DEVICE screen select the COM port of your PC that will be connected to the NTCPU serial port.

Aspila Ex PCPro/WebPro Installation Manual 21

Serial Connection for Local Access
8. At the CONNECTION AVAILABILITY screen select ANYONE’S USE and click NEXT.

9. At the COMPLETED THE NEW CONNECTION WIZARD screen click FINISH.

22 Aspila Ex PCPro/WebPro Installation Manual

 Serial Connection for Local Access
10. At the CONNECTION screen click PROPERTIES and set the Baud rate to 19200 (the default baud rate of the NTCPU
card set in Program 10-21-02) and enable Hardware Flow Control, click OK to save the settings. Enter the USER NAME
and PASSWORD of the Aspila EX that you will connect to and click CONNECT.

Aspila Ex PCPro/WebPro Installation Manual 23

Using PCPro
Using PCPro

Using PCPro
1. When you are using a local LAN connection, skip to Step 3.
When using a remote ISDN dial up connection, Local USB connection or Local Serial connection you must first connect
to the Aspila EX using the dial-up connection. If not already connected, click on START + SETTINGS + NETWORK
CONNECTIONS + select the dial up connection to be used to connect to the Aspila EX system.
2. In the window that appears, if the user name and password are acceptable, click DIAL.
3. To start the PCPro application, click on START + PROGRAMS + ASPIRE PCPRO + ASPIRE PCPRO.
4. The application opens to the main screen.
5. In order to download (from the Aspila EX system to your PC) the database, first click COMMUNICATIONS-CON-
NECT. Enter the IP address from the table below as appropriate for the connection type.

Local Serial Connection 192.78.0.1 Fixed - cannot be changed.

Local USB Connection 192.78.0.2 Fixed - cannot be changed.
Remote ISDN Connection 192.78.0.3 Fixed - cannot be changed.
Local LAN (Ethernet) 172.16.0.10 This setting is defined in Program 10-12-01
and can be changed.

6. Once connected (all the icons on the toolbar will become active), you can then click on COMMUNICATIONS + DOWN-
LOAD to receive all system information. Ensure that you select DOWNLOAD, if you select upload you could send an
incorrect database to the NTCPU, see notes below.
7. After making changes in a window, click the APPLY or OK icon. You can then upload the changed programs to the sys-
tem (without clicking the APPLY or OK icon, the changes will not be saved). With PCPro, the changes must be uploaded
to the system before the changes can take effect.
When changes are made to the following programs, the Aspila EX system must be restarted (powered off/
on) after the data is uploaded to the system.
10-12-01 10-14 80-01 84-03-01 84-05-02 84-06-07
10-12-02 10-15 80-02-01 84-03-02 84-06-01 84-06-08
10-12-03 10-16-01 80-02-02 84-03-06 84-06-02 84-06-09
10-12-04 10-16-02 80-02-03 84-03-07 84-06-03 84-06-10
10-13-01 10-16-03 80-02-04 84-03-08 84-06-04 84-06-11
10-13-02 10-16-04 80-03 84-04 84-06-05 84-09
10-13-03 20-01-03 80-04 84-05-01 84-06-06 84-10

8. When you wish to exit PCPro, disconnect from the system by clicking COMMUNICATIONS + DISCONNECT. Make
sure to save the database file, if needed, prior to exiting the application.
9. If you are connected via a dial up connection (remote access) you must also disconnect the dial up connection. Click
START + SETTINGS + NETWORK CONNECTIONS. Select the dial up connection and click the DISCONNECT but-
ton.

To create a new database: This can be done offline.

- Click FILE + NEW. Select either MEDIUM (for a one-cabinet system) or LARGE (for a two-cabinet system).
- Define the PCB layout for the system by dragging the PCB card name (from the list on the right) to the correct cabinet
and slot number.
- Change other system programs as required.
OR
To open an existing database: This can be done offline.
- Click FILE + OPEN and select the database file.

Notes:
• The PCPro software provides a Help system if you experience difficulty in using the program. Simply press the
‘F1’ key.

24 Aspila Ex PCPro/WebPro Installation Manual

 Using PCPro
• While connected with PCPro, system phone programming is not permitted by the system. Also, if system phone
programming is in use you can not connect to PCPro.
• If you select UPLOAD by mistake and begin sending an incorrect databse you can click the Cancel button to stop
the database being updated. The database will not be updated on the Aspila EX until all the selected items have
been sent and “Processing data remotely” is displayed in the upload screen.

Common Buttons within PCPro and WebPro

Aspila Ex PCPro/WebPro Installation Manual 25

Using WebPro
Using WebPro

Using WebPro
The WebPro software is installed on the Aspila EX NTCPU PCB - there is no separate software installation. This means that
when the Aspila EX system software is updated, the WebPro software is updated as well.

With either Internet Explorer or Netscape Navigator installed:

1. Open the internet browser application. When using a remote ISDN dial up connection, Local USB connection or Local
Serial connection you must first connect to the Aspila EX using the dial-up connection. If not already connected, click on
START + SETTINGS + NETWORK CONNECTIONS + select the dial up connection to be used to connect to the Aspila
EX system.
2. Enter the IP address of the Aspila EX system. This address is selected based on the type of connection to the Aspila EX.
Local Serial Connection 192.78.0.1 Fixed - cannot be changed.
Local USB Connection 192.78.0.2 Fixed - cannot be changed.
Remote ISDN Connection 192.78.0.3 Fixed - cannot be changed.
Local LAN (Ethernet) 172.16.0.10 This setting is defined in Program 10-12-01
and can be changed.

3. When the connection to the system is made, you’ll see the opening page requesting a user name and password. The default
settings are:
User Name Password
ASPIRE 12345678 (Installer Level)
ADMIN1 0000 (SA Level)
ADMIN2 9999 (SB Level)

The passwords are case-sensitive and must be entered as shown.

These passwords can be changed or additional passwords added after accessing WebPro by clicking
PCPRO SETTINGS, then clicking ACCOUNT SETUP.
4. After making changes in a window, click on either the APPLY or OK icon to accept the changes. The system is immedi-
ately updated.
5. When you wish to exit WebPro, you MUST click LOGOUT from the Home page in order to log out of the system.

Notes:
• The WebPro software provides a Help system if you experience difficulty in using the program. Simply press the
‘F1’ key.
• When accessing via remote dial up, USB or Serial the screen refresh will be much slower than a Local LAN con-
nection.

26 Aspila Ex PCPro/WebPro Installation Manual

Aspila EX PCPro/WEBPro NEC Infrontia Asia Pacific Sdn Bhd
Installation Manual Lot 24, Jalan Juruhebah U1/50, .
Temasya Industrial Park Phase 2, Seksyen U 1 ,
991092-5
Glenmarie, 40150 Shah Alam, Selangor Darul Ehsan.
Tel: (+603) 55695888 Fax: (+603) 55693839
www.necinfrontia-ap.com