Flexmove FK (45 MM) Conveyor System: Installation, Maintenance & Parts Manual

FlexMove FK (45 mm)
Conveyor System
Installation, Maintenance & Parts Manual
For other service manuals visit our website at:

www.dornerconveyors.com/manuals-literature
Record Conveyor Serial Number Here

851-904 Rev. A
Table of Contents
Introduction ......................................................................... 4 Chain Assembly at Chain Disconnecting
Warnings − General Safety ................................................. 5 Module FKCC ................................................................ 21
Product Description ............................................................. 6 Install Guiding ................................................................ 22
Specifications ...................................................................... 7 Length Adjustment of the Conveyor Chain................ 22
Conveyor Supports: ......................................................... 7 End Drive Units and Catenary Drive Units............. 22
Maximum Distances:.................................................... 7 Intermediate Drive Units and
Installation ........................................................................... 8 Horizontal Bend Drive Unit .................................... 22
Introduction...................................................................... 8 Guide Rail System Installation ................................... 22
Document Disposition ..................................................... 8 High Side Guiding ...................................................... 22
Initial Assembly Planning................................................ 8 Heavy Duty Fully Adjustable Guiding ....................... 23
Safeguarding .................................................................... 8 Puck/Pallet Guiding .................................................... 25
Considerations ................................................................. 8 Adjustable Guide Rail Bracket ................................... 26
End Drive Unit................................................................. 8 Assembly with Different Guide Rail Support ......... 26
Idler Unit.......................................................................... 8 FGRF- 42x18V Guide Rail Bracket Assembly .......... 27
Catenary Drive Unit......................................................... 8 Assembly with Different Guide Rail Support ......... 27
Assembly Order ............................................................... 8 FGRF- 42x18V Spacer Assembly .............................. 28
Tools General................................................................... 8 FGRB- 40x18, FGRB- 40x20 and
Tools............................................................................. 8 FGRB- 40x15x20 Guide Rail Bracket Assembly....... 28
Hand Tools ................................................................... 9 Method 1 ................................................................. 28
Power Tools.................................................................. 9 Assembly with Different Guide Rail Support ......... 29
Fasteners .......................................................................... 9 Method 2 ................................................................. 29
Standard Fasteners........................................................ 9 Fixed Guide Rail Bracket Installation ........................ 30
Square Nut.................................................................... 9 Guide Rail Connecting Installation............................. 30
Spring Nuts................................................................... 9 Rail Connecting....................................................... 30
Connecting Strip........................................................... 9 Connecting Plug ...................................................... 30
T-Bolt ......................................................................... 10 Guide Rail Cover Installation ..................................... 31
Pre installation Information ........................................... 10 Final Preparations........................................................... 31
Cutting FlexMove Beam ............................................ 10 Plug Beam Ends.......................................................... 31
Saw Requirements...................................................... 10 Anchor Feet to the Floor............................................. 31
Working Site .............................................................. 10 Other Preparations ...................................................... 31
Quality of Cut............................................................. 10 Start-Up and Testing ...................................................... 31
Assembly.................................................................... 10 Safety Considerations ................................................. 31
Foot Installation ............................................................. 11 Safeguarding can be achieved by:........................... 32
Conveyor Installation..................................................... 12 Torque Limiter Adjustment for
Option 1...................................................................... 12 Suspended Drive Units ............................................... 32
Option 2...................................................................... 12 Introduction ............................................................. 32
Option 3...................................................................... 12 Name of Parts .......................................................... 32
Mounting Conveyor Beam Support Bracket ................. 12 Torque Setting............................................................. 32
Conveyor Beam Installation .......................................... 13 Replace the Friction Facing ........................................ 32
Drive Unit and Idler End Unit Installation .................... 14 Maintenance and Precautions
Drive End ................................................................... 14 after the Replacement Procedure ................................ 32
Drive Tail Support Brackets....................................... 14 Safety .......................................................................... 32
Idler End ..................................................................... 14 Preventive Maintenance and Adjustment .......................... 33
Attaching Slide Rail in Straight Beam........................... 15 Start-Up and Maintenance Schedule .............................. 33
Slide Rail End Installation at Connector Beam ............. 16 Chain Lubrication........................................................... 33
Slide Rail Installation at Wheel Bend............................ 17 Wear ............................................................................... 33
Slide Rail Installation at Horizontal Plain Bends Chain Elongation ............................................................ 33
and Vertical Bend .......................................................... 17 Inspection ....................................................................... 34
Drilling Slide Rail .......................................................... 17 Drive Unit....................................................................... 34
Fixing Slide Rail ............................................................ 18
Nylon Screw ............................................................... 18
Joining Chain End.......................................................... 19
Chain Installation at Drive Unit..................................... 20
FlexMove FK (45 mm) Conveyor System

Dorner Mfg. Corp. 2 851-904 Rev. A
Table of Contents
Maintenance Schedule.................................................... 34 Horizontal Mounting Brackets....................................... 76
First 3rd Month, 6th Month, and Support Post - Conveyor Frame Mount ........................ 77
Every 6th Month Following........................................ 34 Support Post - Motor Mount ......................................... 78
Checking Slide Rail with the Suspended Drive Stand ................................................. 79
Conveyor Chain in Place ............................................ 34 Dual Side Support Post ................................................. 80
Checks When the Chain is Removed.......................... 35 E-Drive Gearmotor Mounting Package ......................... 81
Horizontal Bends ........................................................ 35 Standard Load 90° Industrial Gearmotors ..................... 82
Safety Devices ............................................................ 35 Flange Mounted Motor (Direct Drive Tail) ................... 83
Troubleshooting.............................................................. 36 Foot Mounted Motor (Suspended Drive Tail) ............... 84
Required Tools ............................................................... 37 Slide Rail Replacement Tool ......................................... 85
Conveyor Chain Replacement....................................... 37 Slide Rail........................................................................ 85
Replacing a Section or Entire Chain........................... 37 Replacement Chain ........................................................ 85
Conveyor Chain Tensioning........................................... 38 Belt Removal Tool ......................................................... 86
Slide Rail Replacement .................................................. 38 Side Cutter...................................................................... 86
Idler Pulley Replacement ............................................... 38 Utility Cutter .................................................................. 86
Drive Spindle Shaft Replacement .................................. 39 Bearing Tool .................................................................. 86
Retaining Guide Replacement........................................ 40 Notes .............................................................................. 87
Cantenary Drive End .................................................. 40 Return Policy.................................................................. 88
Idler End and GP Drive Tail ....................................... 41
Wheel Bend Servicing.................................................... 42
Power Transfer ............................................................... 42
Removal ...................................................................... 42
Installation .................................................................. 45
Service Parts....................................................................... 48
Drive Tail........................................................................ 48
Guided Profile (GP) Drive Tail ...................................... 50
FKSD-A45 Suspended Drive ......................................... 52
FKID-DD-0L1/0R1 Intermediate Direct Drive.............. 54
FKID-SD-0L1/0R1 Intermediate Suspended Drive ....... 55
Idler Tail ......................................................................... 56
Frame Assembly............................................................. 58
Curve Frame Assembly .................................................. 59
Knuckle Frame Assembly .............................................. 60
#4 & #5 High Sides for Straight Modules ...................... 61
#4 & #5 High Sides for Curve Modules......................... 62
#4 & #5 High Sides for Incline/Decline Modules .......... 63
#13 & #14 Heavy Duty Fully Adjustable Guiding......... 64
#17 & #18 - Puck / Pallet Guiding ................................. 65
Type A - Fixed Guiding (16x54).................................... 66
Type B - Fixed Guiding (16x42) .................................... 66
Type C - Fixed Guiding (28x42) .................................... 67
Type D - Fixed Guiding (40x42).................................... 67
Type E - Fixed Guiding (49x42) .................................... 68
Type F - Fixed Guiding (53x42) .................................... 68
Type G - Fixed Guiding (90x42).................................... 69
Type H - Adjustable Width Guiding (8x39x45)............. 69
Type J - Adjustable Width Guiding (26x39x45)............ 70
Type K - Adjustable Width Guiding (40x18)................. 70
Type L - Adjustable Height Guiding (18x110) .............. 71
Type M - Adjustable Height Guiding (18x150) ............. 71
Type N - Fully Adjustable Guiding................................ 72
Type P - Fully Adjustable Guiding ................................ 72
Type Q - Dual Rail Guiding ........................................... 73
Type R - Dual Rail Guiding ........................................... 73
Type S - Adjustable Height Guiding .............................. 74
Power Transfer ............................................................... 75

851-904 Rev. A 3 Dorner Mfg. Corp.
Introduction
Dorner has convenient, pre−configured kits of Key Service
IMPORTANT Parts for all conveyor products. These time saving kits are
easy to order, designed for fast installation, and guarantee
Some illustrations may show guards you will have what you need when you need it. Key Parts
removed. DO NOT operate equipment and Kits are marked in the Service Parts section of this
without guards. manual with the Performance Parts Kits logo .
Dorner reserves the right to make changes at any time
Upon receipt of shipment: without notice or obligation.
• Compare shipment with packing slip. Contact factory
regarding discrepancies.
• Inspect packages for shipping damage. Contact carrier
regarding damage.
• Accessories may be shipped loose. See accessory instruc-
tions for installation.
Dorner’s Limited Warranty applies.

Warnings − General Safety
A WARNING A WARNING
The safety alert symbol, black triangle with
white exclamation, is used to alert you to
potential personal injury hazards.
Dorner cannot control the physical

A DANGER installation and application of conveyors.
Taking protective measures is the
responsibility of the user.
When conveyors are used in conjunction
with other equipment or as part of a multiple
conveyor system, CHECK FOR POTENTIAL
Climbing, sitting, walking or riding on
PINCH POINTS and other mechanical
conveyor will cause severe injury. KEEP OFF
hazards before system start-up.
CONVEYORS.
A DANGER A WARNING
DO NOT OPERATE CONVEYORS IN AN

EXPLOSIVE ENVIRONMENT. Loosening stand height or angle adjustment
screws may cause conveyor sections to drop
down, causing severe injury.
A WARNING SUPPORT CONVEYOR SECTIONS PRIOR TO
LOOSENING STAND HEIGHT OR ANGLE
ADJUSTMENT SCREWS.
Exposed moving parts can cause severe

injury. LOCK OUT POWER before removing
guards or performing maintenance.
A WARNING
Gearmotors may be HOT.

DO NOT TOUCH Gearmotors.

Product Description
Refer to Figure 1 for typical components.
1 Infeed Module
2 Curve Module
3 Incline Module
4 Decline Module
5 Intermediate Module
6 Drive Module
7 Gearmotor
8 Stands
Figure 1
4 5
1 3
2
6
Figure 1

Specifications
Conveyor Supports:
Maximum Distances:
1 = 914 mm (36")
2 = 3000 mm (118")*
3 = 914 mm (36")
* For conveyors longer than 3000 mm (118"), install support
at joint.
Note: Additional support required on 180° curve modules.
Figure 2
1 2 3
Figure 2

Installation
Introduction Idler Unit
The main purpose of this manual is to help self-building end The opening between links (when they turn around idler)
users, with little or no prior experience, to assemble a could be a potential risk. The idler end should not be
FlexMove conveyor system. Each chapter includes detailed accessible during conveyor operation.
instructions and pictures showing how to assemble the
different parts. Most pictures in the manual include parts Catenary Drive Unit
from the FS conveyor system, but all instructions are
applicable to the FH, FK, FS, FM, FC, FL, FU and FV. The bridge area where the chain goes down should not be
accessible during conveyor operation.
Document Disposition
The document is divided into the following five main parts:
Assembly Order
• Installation site preparations During the conveyor assembly, the following items can be
used as a checklist:
• Tools and fasteners
• Cut all beams to desired length.
• Assembly
• Connect all feet and structural beams.
• Start-up and testing
• Mount conveyor beam support brackets.
Initial Assembly Planning • Assembly conveyor beams and mount them onto the sup-
port structure.
Systematically working planning is required:
• Mount drive and idler unit at the end of the conveyor.
• Fully understand and studying the assembly drawing. • Mount slide rail onto the conveyor beam.
• Ensure the necessary tools are required. • Loosen the slip clutch at the drive unit.
• Ensure all the parts and materials are well prepared in • Check any obstruction of the conveyor with a short piece
advance, following the parts list. chain.
• Enough space for conveyor installation is important. • Assemble and mount necessary chain onto the conveyor.
• Ensure the floor is even and so the foot can be properly • Mount guide rail and other accessories required onto the
attached on the floor. conveyor.
• Tighten the slip clutch with suitable friction.
Safeguarding
• Read the final preparations at the end of this manual.
All pinch and shear points, as well as other exposed moving
parts that present a hazard to users, is recommended to be Tools General
safe guarded. Cleat conveyor chain is more susceptible of
creating pinch and shear points than plain chain.
When two or more pieces of equipment are interfaced, Tools
special attention must be given to the interfaced area to To assemble a FlexMove Conveyor, you may need most of
ensure proper safeguarding. the tools listed on the following page. Not all are essential,
For overhead conveyors, guards must be provided if but they will make your work easier and efficient.
products fall off the conveyor for some reason. The same
applies to all incline, decline and vertical conveyors.
Considerations
When correctly applied, the conveyor components are safe
to use or maintain. It is, however, necessary for those
responsible to design, installation, operation and
maintenance to be aware of certain areas when special
caution is required.
End Drive Unit

The chain slack of a normal direct drive unit must be
maintained during the system lifetime.

Installation
Hand Tools Square Nut
• Wrench Square nuts (Figure 4) can be slid into T-slot of FlexMove
• Slide rail cutter conveyor and support beams. They do not stay in place in
vertical positions and have to be inserted from the end of
• Set of metric hex keys beam. Remember to put in a sufficient number before
• Counter sink bit completing the assembly.
Figure 4
• Drill fixtures for slide rail

• Riveting tool
• In addition, the tools listed below can be useful:
- Files
- Socket wrench
- Screwdriver
- Pliers Figure 4
- Knife (burr of slide rail)
- Flush cutting pliers Spring Nuts
- Soft head hammer Spring nuts (Figure 5) can be inserted into the T-slot of
- Chain tools (for chain installation and dismantle) FlexMove conveyors and support beams. They do not stay in
place in vertical positions.
- Level Figure 5
Power Tools
• Hand drill
• Drill bit (for fixing slide rail)
Fasteners
Standard Fasteners
Standard Fasteners (Figure 3): Figure 5
• M8 = Washer, Countersink Cap Screw, Nut, Lock Nut

Connecting Strip
• M6 = Washer, Countersink Cap Screw, Nut, Lock Nut
Figure 3
Connecting strips (Figure 6) are used for joining end to end
of beams. Use hex key and set screws when attaching the
connecting strip to the beam.
Figure 6
Figure 6
Figure 3

Installation
T-Bolt Assembly
T-bolts (Figure 7) can be entered from the beam side, and The basic FlexMove conveyor structure consists of five
when turned 90 degrees they will stay in place after component groups (See (Figure 8) and (Figure 9)):
tightening with lock nuts. Use lock nuts to facilitate T-bolt Figure 8
turning in slot. The indication groove in the T-bolt should be

at 90 degrees to the conveyor T-slot. T-bolts are used when
attaching support brackets, guide rails and drip trays to the
conveyor beam. T-bolts should not be used when fine
adjustment for exact positioning is required (use square nuts
or spring nuts for this type of application). Do not use T-bolts
with support beams.
Figure 7
Figure 8
Figure 9
Figure 7
Pre installation Information

Cutting FlexMove Beam
Cutting is required for all 3m beams, including a precise cut
to 3m lengths. Study your drawing to determine the beam
lengths required before cutting.
Saw Requirements
The circular cross-cut saw used for aluminum profile cutting
must be equipped with carbide tip saw circulating at high
speed for a clean cut. The saw should have the ability of
cutting the largest profile in one single cutting action.
Figure 9
A WARNING • Support structure
All safety precautions issued by the cutting • Conveyor beams, straight sections, and bends
saw manufacturer should be followed at all • Drive and idler units
the times.
• Chains
• Guide rail assembly components
Working Site
• Other accessories
You should use a special area for cutting beams in order to The first step in the assembly process is to assemble the
keep the assembly area clean. support structure, which consists of feet, support beams, and
beam support brackets. Most conveyor support designs are
Quality of Cut based on vertical support beams, combined, if necessary,
with horizontal support beams. There are also a number of
If burrs are evident, they must be removed prior to assembly. different feet and beam support brackets, so check which
Make sure the cut is straight for proper assembly. ones are suitable to use in your application.

Installation
Foot Installation 3. Raise the beam from the bottom of the foot
approximately 40-50 mm (Figure 12, item 1), to allow
1. Insert hex head screws and washers (Figure 10, item 1) for height adjustment later in the assembly.
into the holes on the side of the foot. Use the screws to Figure 12
fasten foot connecting strips to the inner side of the foot.

Leave loose.
Figure 10
1
1
Figure 12
4. Tighten the screws using a wrench (Figure 13, item 1).
Figure 10 Figure 13
2. Slide the connecting strips (Figure 11, item 1) into the

structural beam T-slots.
Figure 11
1
1
Figure 13
Figure 11

Installation
Conveyor Installation Option 3
Conveyor beams are mounted on to the support structure by Dual side mounting brackets (Figure 16, item 1) are used to
means of support brackets. There are three different types of support 180° wheel corners.
conveyor beam support brackets. They all serve the same Figure 16
purpose but are connected to the structural beams in different

ways.
Option 1
1
Horizontal beam support brackets (60mm or 80mm)
(Figure 14, item 1) are used for horizontal support structure
mounted to 64x64mm or 80x80mm support beams.
Figure 14
Figure 16
1
Mounting Conveyor Beam Support
Bracket
1. Attach screws, nuts and washers to the support bracket
(Figure 17, item 1) before mounting. (Screws and
square nuts are support beam fasteners; T-bolts and nuts
are conveyor beam fasteners.) Slide the square nuts of
Figure 14 one support bracket into the support beam T-slots.
Tighten the screws. Make sure that the support bracket
Option 2 is aligned with the beam cross-section
(Figure 17, item 2) as shown in the drawing.
Vertical beam support brackets (Figure 15, item 1) are used
with vertical support beams and are made from aluminum.
Figure 17
Figure 15
Figure 17
Figure 15

Installation
2. Insert the square nuts of the second support bracket Conveyor Beam Installation
(Figure 18, item 1) into the support beam T-slots. Slide
the bracket down so that it does not protrude above the The next step is to connect conveyor beams – straight
cross-section of the beam. sections and bends – to each other. Connect all conveyor
Figure 18
beams according to the instructions below.
1 1. Connect two conveyor beam ends by inserting
connecting strips (Figure 21, item 1) into the beam
inner T-slots. Use two connecting strips per beam joint.
Figure 21
Figure 18
3. Use a soft hammer or mallet to mount an end cap
(Figure 19, item 1) on to the support beam.
Figure 19 Figure 21
2. Make sure that the set screws (Figure 22, item 1) do not
prevent the connection strips from sliding into place.
Figure 22
1 1
Figure 19
4. Mount the first support bracket (Figure 20, item 1) to
the conveyor beam (Figure 20, item 1). Pull the second
bracket up and insert the T-bolts into the conveyor beam
T-slot. Tighten the nuts.
Figure 20
Figure 22
1
2
Figure 20

Installation
3. Tighten the set screws using a hex key 2. Tighten the set screws using a hex key
(Figure 23, item 1). (Figure 25, item 1).
Figure 23 Figure 25
1 Figure 25
Drive Tail Support Brackets

Figure 23 1. Attach the drive tail support brackets (Figure
26, item 1) to the slot (Figure 26, item 2) in the drive
NOTE tail with the T-bolts and hex nuts. The brackets should
be located closest to the frame (Figure 26, item 3).
Assemble the entire conveyor beam structure Figure 26
in the same way. If the conveyor beam is too 2

long to mount onto the support structure in 1
3
one continuous length, assemble shorter
lengths and connect them to each other once
fastened to the support beams.
Drive Unit and Idler End Unit

Installation
Drive End
1. Mount the end drive unit (Figure 24, item 1) on to the
end of the conveyor: Release the four set screws that are
inserted into the drive unit connecting strips. Insert the
connecting strips into the T-slot of the beam you want
Figure 26
attached to the end drive unit. Make sure that the set
screws do not prevent the connecting strips from sliding
into place. Idler End
Figure 24
1. Insert the idler unit (Figure 27, item 1) connecting
strips into the T-slots of the beam end and tighten it.
Figure 27
Figure 24
Figure 27

Installation
2. Tighten the set screws using a hex key 2. Make sure the slide rail (Figure 30, item 1) is properly
(Figure 28, item 1). mounted and snaps onto the beam. The longer flange of
Figure 28
the slide rail must always face inside of the beam (See
Figure 31).
Figure 30
Figure 28
A CAUTION
The opening between the links when they
turn around the idler could be a risk. Idler
ends should not be accessible during
conveyor operation.
Figure 30
Attaching Slide Rail in Straight
Figure 31
Beam Correct Installation

1. Start the slide rail assembly at an idler end unit
(Figure 29, item 1). Separate the top and bottom flange
of the slide rail at the end of rail and press into place.
Figure 29
Wrong Installation
1
Figure 29
Figure 31

Installation
3. The slide rail (Figure 32, item 1) must be mounted 3. Do not place two slide rail joints (Figure 35, item 1)
across the entire beam section. Remember to mount opposite each other. Make sure there is a distance of at
slide rails on both top and bottom side of the beam least 100 mm (Figure 35, item 2) between them to
(unless top running chain only). make the chain run smoother. This does not apply to
Figure 32
slide rail that begins by an idler unit or after a drive unit,
where joints are always parallel.
Figure 35
1
20
10 60
35˚ 4
2
1 5 1 FLOW
100
Figure 32
Slide Rail End Installation at

Connector Beam Figure 35
1. Cut both slide rail ends at a 35° angle. The beginning of Try to let the slide rail run in as continuous lengths as
a new slide rail (in the direction of travel) must cut back possible by reducing number of breaks, except in
circumstances stated below:
at a small angle (Figure 33, item 1).
Figure 33 • It is recommended to use short slide rails 2–3m (78-3/4”–
118”) where chemicals may have an effect on the slide rail
composition.
1 • It is important to cut the slide rail and allow for elongation
in high load areas. Cutting is required in wheel and hori-
zontal bends (see following page), at idler units and where
the conveyor will be heavily loaded. This prevents the
slide rail from stretching out and entering into the drive
unit, which may block the chain movement.
• Never join slide rail in horizontal or vertical bends, since
forces are higher on the slide rail in these sections. Instead,
place the joint before the bend.
• Avoid joining slide rails on top of conveyor beam joints.
Figure 33
2. Allow a space of approximately 10 mm
(Figure 34, item 1) between two slide rail ends. The
travel direction is indicated by an arrow.
Figure 34
1 1
Figure 34

Installation
Slide Rail Installation at Wheel Bend Slide Rail Installation at Horizontal
1. Infeed Wheel Bend: Cut the slide rail end (Figure Plain Bends and Vertical Bend
36, item 1) in flat. Make sure there is a 5 mm gap In plain bends with a small radius, the slide rail for the inner
created at the plastic molding part. The step is applied bend should be cut so that it is only 10 mm wide in the bend.
onto outfeed as well. This is to prevent an uneven slide rail surface. Stretch the
Figure 36 slide rail while mounting.
Drilling Slide Rail

1. Drill two holes near the beginning of each slide rail
section. Use the drill fixture (Figure 39, item 1) to
ensure clean-cut holes and the correct location of the
holes. The holes must be at the leading edge of the joint
1
piece, in the direction of travel, to hold the slide rail in
place when the conveyor is in use. Use a well sharpened
1/8", #31, or 3.2mm drill bit.
Figure 39
Figure 36
2. Outfeed Wheel Bend: Follow step 1.
Figure 37
1
Figure 39
2. Use a bigger drill bit or countersink bit (Figure
Figure 37 40, item 1) to deburr and countersink the holes. Also
make sure that there are no metal filings left underneath
3. In the outer bend, make sure that the slide rail is the slide rail.
properly connected to the conveyor beam profile. Figure 40
Figure 38
Figure 40
Figure 38

Installation
Fixing Slide Rail
Figure 43
The beginning of each slide rail section must be fixed to the

beam, since the chain will cause the slide rail to be pushed
forward. A slide rail which moves into a wheel bend or a
drive unit can block the chain completely. The riveting
method is more secure if the conveyor will run with high
operational speed or be heavily loaded.
Nylon Screw
1. Insert the nylon screws (Figure 41, item 1) into the
holes using a hex driver until the screw is flush with the
bottom of the slide rail.
Figure 41
1
Figure 43
1
3. After the cut, make sure the slide rail surface is smooth
and the nylon screws do not protrude over the slide rail
surface. Use a file (Figure 44, item 1) to file off the
protruding edge if uneven surface is found.
Figure 44
Figure 41
2. Cut off the head of nylon screws by using flush cutting
pliers (Figure 42, item 1) or soft hammer and knife
(Figure 43, item 1). Remember, the cut must be made
away from the joint, in the direction of chain travel.
Figure 42
Figure 44
NOTE
Nylon screws can be used multiple times
before being discarded. Ensure bottom of
screw is cut square before re-using.
Figure 42

Installation
Joining Chain End 3. Line the FlexMove chain tool (Figure 47, item 1) up
with the pin (Figure 47, item 2). Slowly depress the
Assemble the chain by inserting the steel pin that comes with trigger until the pin seats. A slight detent will be felt
each chain link, into the opposite end of another link. Do this when pin is seated.
by using the FlexMove pin insertion tool. Figure 47
1. Insert the plastic pivot (Figure 45, item 1) with the slot
facing outward. 1
Figure 45
Figure 47
Figure 45
4. Check that the chain is flexible in the joint and that the
2. Insert the steel pin (Figure 46, item 1) halfway, using a
pin does not stick out or go through the other side
pair of pliers. Always use new steel pins and plastic
(Figure 48, item 1).
pivots when joining chain ends. Figure 48
Figure 46
Figure 46 Figure 48

Installation
Chain Installation at Drive Unit 3. Join 5 meter lengths of chain when necessary.
(See Figure 52.)
1. Insert the chain (Figure 49, item 1) into the underside Figure 52
of the drive unit (Figure 49, item 2). Make sure the
chain will be moving in the correct direction, as
indicated by the arrow (Figure 50, item 1) located at the
side of all chain links.
Figure 49
2
Figure 52
1
4. Tension the chain and remove links if necessary, so that
the chain will exhibit some slack at the drive unit. Put in
Figure 49 the stainless steel pin (Figure 53, item 1) at the hole
Figure 50
provided at drive unit and join the chain.
Figure 53
Figure 50
2. Feed the chain along the conveyor (Figure 51, item 1)
by pulling it through the idler unit and back to the drive
1
unit.
Figure 51
Figure 53
Figure 51

Installation
Chain Assembly at Chain 3. Clamp the chain (Figure 56, item 1) to the beam
profile. Use the FlexMove chain tool (Figure
Disconnecting Module FKCC 56, item 2) to remove a steel pin from the chain, so that
1. Loosen the screws (Figure 54, item 1) on the beam two links are separated.
section flanges. Figure 56
Figure 54
1
1 1
2
Figure 56
Figure 54 4. Remove excess links and use the chain tool (Figure
57, item 1) to put the chain back together again.
2. Remove the flange (Figure 55, item 1) so that the chain Figure 57
becomes accessible.
Figure 55
1 Figure 57
Figure 55

Installation
Install Guiding 4. The tensioned chain can now be pulled back into
position on the bend guide disc, and the outer profile put
All guiding must be located and installed by the end user. into place.
Length Adjustment of the Conveyor Chain Guide Rail System Installation

End Drive Units and Catenary Drive Units Guide rails are used to guide products being conveyed, but
also to prevent them from falling off the conveyor. Guide
1. The conveyor chain is carried out at the drive end of the rails are supported by guide rail brackets attached to the
conveyor. sides of the conveyor beam. Follow the mounting
2. The transmission guard cover must be removed from the instructions for the type of bracket used in your application.
drive unit and the slip clutch disengaged or transmission Brackets should be placed approximately 500 to 1000 mm
chain removed. The conveyor chain should now be free apart depending on type of product and if accumulation
to travel within the conveyor beam profile. occurs or not. If brackets are spaced at greater distances than
3. Catenary protection plates should also be removed to 1000 mm, there is a possibility that guide rails will become
deformed due to excessive force.
allow easy access for the conveyor chain pin insertion
tool.
4. The conveyor chain should be tensioned within the
High Side Guiding
conveyor system by pulling down the conveyor chain at 1. Install stud (Figure 58, item 1) onto retaining clip
the chain catenary on the underside of the drive unit. (Figure 58, item 2) with nut (Figure 58, item 3).
Clamp across the conveyor chain to trap the chain on to Figure 58
the beam profile. The clamp should be placed over the

edges of the drive unit to reduce the risk of damage to
the aluminum profile.
2
5. Remove all slack links from the conveyor chain using
the pin insertion tool.
6. Rejoin the conveyor chain using a new steel pin and 4
plastic pivot.
7. Remove the chain clamp and replace the catenary
protection plate and transmission chain. The slip clutch
should also be reset.
8. Replace the transmission guard cover. The conveyor is
now ready for operation.
Intermediate Drive Units and Horizontal Bend Drive 3 1

Unit
1. Conveyors which have no conveyor chain slack should
be assembled with a special section of conveyor beam
Figure 58
(FKCC), which allows for the chain to be easily inserted
and adjusted for tension. (See “Chain Assembly at 2. Install stud (Figure 58, item 1) into side rail channel
Chain Disconnecting Module FKCC” on page 21.) (Figure 58, item 4). The end clips should be no greater
2. Remove the lower part of this conveyor beam section by than 12" from end of the conveyor.
releasing the four screws.
3. Lift the chain from this section of the beam and clamp
the conveyor chain as described above. Adjust the chain
tension as for end and catenary drive units.
In a wheel bend drive, the outer aluminum profile can be
removed by loosening the set screws in the beam connecting
strips. The slide rail must be fitted to allow the removal of
this section.
1. After removal of the outer aluminum profile, the
conveyor chain can be pulled out of the wheel bend disc.
Lift the chain upwards.
2. Remove chain links using the pin insertion tool.
3. New steel pins and plastic pivots must be used when
rejoining chain ends.

Installation
3. Fasten retaining clip (Figure 59, item 1) to conveyor Heavy Duty Fully Adjustable Guiding
with nut (Figure 59, item 2) on stud.
1. Install guide bracket assembly (Figure 61, item 1) into
the conveyor T-slot (Figure 61, item 2).
Figure 59
Figure 61
2
1
2
3
Figure 61
2. Tighten screws (Figure 62, item 1) making sure T-nut
Figure 59
(Figure 62, item 2) rotates and engages inside of the T-
slot.
NOTE Figure 62
Be certain that slot (Figure 59, item 3) is

close to vertical when finished tightening nut.
4. Tighten nuts (Figure 59, item 2).

5. Install guide (Figure 60, item 1) and retaining clip
(Figure 60, item 2) to conveyor side rail with socket
head screw (Figure 60, item 3).
Figure 60
1
1
Figure 62
2
3
Figure 60

Installation
3. Loosen screw (Figure 63, item 1) on end of shaft
Figure 66
(Figure 63, item 2) to remove clip (Figure 64, item 1).

Figure 63
Figure 66
6. Adjust rail width with top screw (Figure 67, item 1).
Figure 63 Figure 67
Figure 64
Figure 67
Figure 64
7. Adjust rail height with lower screw (Figure 68, item 1).
4. Snap clip (Figure 65, item 1) onto guide rail (Figure Figure 68
65, item 2).

Figure 65
1
1
Figure 68
Figure 65
5. Reassemble clip (Figure 66, item 1) and attach to shaft
(Figure 66, item 2). Tighten screw (Figure 63, item 1)
on end of shaft.

Installation
Puck/Pallet Guiding
Figure 71
1. Install clip assembly (Figure 69, item 1) into side rail

channel (Figure 69, item 2). The end clips should be no 1
greater than 12" from the end of the conveyor.
Figure 69
1
2
3
4
Figure 71
2
NOTE
If guide length is less than 250 mm (10”), pin
Figure 69 plastic guide to rail using slide rail screw and
cutting flush.
NOTE
5. Attach guiding (Figure 72, item 1) to clip (Figure
Make sure that the studs (Figure 69, item 4) 72, item 2) and tighten screw (Figure 72, item 3).
rotate inside the channel and engage with the Figure 72
conveyor.
2. Fasten clip (Figure 69, item 1) to conveyor with nut 1

(Figure 69, item 3) on stud.
3. Tighten nuts (Figure 70, item 1).
NOTE
Be certain that slot (Figure 70, item 2) is 2
3
close to vertical when finished tightening nut.
Figure 70
Figure 72
1
3
2
4
Figure 70
4. Attach slide rail (Figure 71, item 1) to guiding (Figure
71, item 2).

Installation
Adjustable Guide Rail Bracket Assembly with Different Guide Rail Support
1. Fasten an adjustable guide rail bracket support (Figure Option 1
73, item 1) to the conveyor beam using T-bolt (Figure Figure 75
73, item 2).

Figure 73
1
2
Figure 73
2. Attach the guide rail (Figure 74, item 1) to the clamp
(Figure 74, item 2). Tighten the screw (Figure
74, item 3). Remember, do not over tighten the screw. Figure 75
Figure 74
Option 2
3 Figure 76
Figure 74
3. Use a wrench (Figure 74, item 4) to tighten the guide
rail to the frame. Remember, do not over tighten the
screw. Install remaining brackets.
Figure 76
NOTE
Tighten the screws when the position is
justified.

Installation
FGRF- 42x18V Guide Rail Bracket Assembly with Different Guide Rail Support
Assembly Option 1
1. Prepare the heavy-duty guide rail bracket (Figure Figure 79
77, item 1) with T-bolt (Figure 77, item 2).

Figure 77
Figure 79
Option 2
Figure 77 Figure 80
2. Attach the bracket onto conveyor beam and tighten with

a socket wrench (Figure 78, item 1).
Figure 78
Figure 80
Option 3
Figure 81
Figure 78
Figure 81

Installation
FGRF- 42x18V Spacer Assembly FGRB- 40x18, FGRB- 40x20 and
1. Attach the spacer (Figure 82, item 1) onto FGRB- 40x15x20 Guide Rail Bracket
FGRF- 42x18V (Figure 82, item 2) and install correct Assembly
length T-bolt (Figure 82, item 3).
Figure 82
Method 1
1. Open the upper and lower caps (Figure 84, item 1) on
FGRB - 40 guide rail bracket (Figure 84, item 2), and
install T-bolt.
Figure 84
3 1
1
2
2
Figure 82
1
a socket wrench (Figure 83, item 1).
Figure 83
Figure 84
a socket wrench (Figure 85, item 1). Install upper and
lower caps.
Figure 85
Figure 83
Figure 85

Installation
Assembly with Different Guide Rail Support Method 2
Option 1 1. Open the upper and lower caps (Figure 88, item 1) and
Figure 86
prepare the FGRB - 40 guide rail bracket (Figure
88, item 2) with T-bolt.
Figure 88
Figure 86
Figure 88
Option 2
Figure 87
a socket wrench. Install both caps of the bracket.
Figure 89
Figure 87
Figure 89
NOTE
Tighten all the screws when the position is
justified. Remember to assemble the upper
and lower caps onto the bracket.

Installation
Fixed Guide Rail Bracket Installation Guide Rail Connecting Installation
1. Fasten a fixed guide rail bracket support
(Figure 90, item 1) to the conveyor beam using T-bolt. Rail Connecting
Figure 90 1. Slide the guide rail sleeve (Figure 92, item 1) into
either one of the guide rail profile that you are going to
1 join.
Figure 92
Figure 90
2. Attach the guide rail (Figure 91, item 1) to the bracket Figure 92
(Figure 91, item 2). Clamp the spring pin into the slot 2. Move the guide rail sleeve into second profile. Tighten
between bracket and guide rail to the fixed position. set screws.
Figure 91 Figure 93
Figure 93
Figure 91 Connecting Plug

1. Connecting plugs (Figure 94, item 1) are pressed into
two guide rail ends with soft hammer.
Figure 94
Figure 94

Installation
Guide Rail Cover Installation Other Preparations
1. To prevent products from being scratched, a plastic • Adjust the height of the structural beam if necessary.
guide rail cover (Figure 95, item 1) can be snapped on
• Make sure that the installation is stable and that all screws
to the inside of the guide rail. have been properly tightened.
Figure 95
• Make sure that all electrical equipment and power supply

1 are properly connected.
• Make sure that the conveyor is running in the correct
direction before starting the conveyor!
• Tighten the slip clutch to a suitable friction.
• Make sure that all chain and belt covers are attached
correctly.
• In pallet installations, make sure that all pneumatic equip-
ment is properly connected.
NOTE
Remember that conveyor chains should
Figure 95 always be pulled, not pushed, by the drive
unit.
2. Make sure that all cover joints (Figure 96, item 1) are
smooth, so that products do not get caught or damaged.
Covers are not required on guide rail joints. Start-Up and Testing
Figure 96
1 Safety Considerations
To eliminate the risk of accidents, it is important to be aware
of certain areas of the conveyor where special caution is
required, during installation, operation, and maintenance.
Some areas present a higher danger to personal safety, and
various kinds of safety devices need to be installed.
• All pinch and shear points as well as other exposed mov-
ing parts that present a hazard to employees at their work-
stations or their passageways must be safeguarded.
• Cleated conveyor chains are more susceptible of creating
pinch and shear points than plain chain.
Figure 96 • When two or more pieces of equipment are interfaced,
special attention must be given to the interfaced area to
Final Preparations ensure proper safeguarding.
• For overhead equipment, guards must be provided if prod-
ucts may fall off the equipment for some reason. The same
Plug Beam Ends applies to all incline, decline, and vertical conveyors.
Ensure that end caps have been fitted to all aluminium
profile ends. The beam profiles should be deburred before
fixing end caps. It may be necessary to fix the cap into
position using a soft-faced hammer.
Anchor Feet to the Floor

After the assembly of all components, it is recommended to
anchor the conveyor support feet to the floor. Use a type of
fastener that is right for the kind of floor where the conveyor
is installed.
Instability of the conveyor during operation may result in a
dangerous operating environment or damage the conveyor
components.

Installation
Safeguarding can be achieved by: Torque Setting
• Location – locate the hazardous area out of reach of the
personnel involved. NOTE
• Guards – mechanical barriers preventing entry into the
hazardous area or protecting against falling goods. It may be easier to adjust torque limiter off of
• Control devices – machine controls preventing or inter- conveyor to adequately secure inner race with
rupting hazardous conditions. shaft locked in a vise while turning adjusting
nut.
• Warnings – instructions, warning labels, or sound or light
signals, alerting on hazardous conditions.
Tighten adjusting nut hand tight (approximately ¼ turn after
• Warnings shall be used when other means of safeguarding first making contact). Mark nut flat closest to keyway.
will impair the function of the installation. Continue to tighten to specified rotation to achieve desired
torque:
A WARNING
Rotation Slip Chain
It must be difficult to bypass or inactivate Angle Torque Pull
safeguards during operation! Safety devices
should be designed to minimize discomfort 30 Degrees 13 Nm 203 N
or difficulties for operators. 60 Degrees 21 Nm 328 N
90 Degrees 29 Nm 453 N
Torque Limiter Adjustment for Suspended
110 Degrees 33 Nm 500 N
Drive Units
Once adjusted nut is tightened to desired rotation, bend
Introduction locking tabs down against nut flats in at least 2 locations.
The slip clutch on the drive unit is a safety device which
allows the chain to stop if the load becomes excessive. It has Replace the Friction Facing
two purposes:
• Prevent damage to conveyor Change the friction facing when they reach roughly half the
thickness of 1.6 mm (0.063 in.). Before replacing the friction
• Prevent damage to the products on the conveyor facing, each part must be completely free of oil, rust and dirt.
(See Figure 97.)
Name of Parts Maintenance and Precautions after the
Figure 97
Replacement Procedure
3 4 5 6
2 Replace the friction facing and bushing if they wear.
7
Keep the torque limiter free from water and oil. If torque
1 limiter slips, re-adjust as necessary.
8
Safety
A WARNING
• Before carrying out maintenance, make
sure there is no load or turning force
applied to the machine.
• Inspect operation periodically for
overloads.
Figure 97
A CAUTION
1 Hub
• Mechanical parts may wear depending on
2 Friction Facing
the rotation speed and slipping time. Check
3 Bushing the operation periodically.
4 Pressure Plate
5 Disk Spring
6 Lock Washer
7 Pilot Plate
8 Adjustable Bolt

Preventive Maintenance and Adjustment
Start-Up and Maintenance Schedule Chain Elongation
The chains are made of acetyl resin, which has an excellent Acetyl resin is an elastic material. In addition to the elastic
combination of strength, wear, chemical resistance, impact elongation, the chain will exhibit elongation because of
strength and temperature range. Chain failures like breakage, material creeping. The magnitude of chain elongation will
pin bending, and high wear might occur if the actual pull is depend on the chain tension. Unless a weighted take-up is
higher than the permissible chain limit. There is also high used, the chain elongation will show up at the bottom of the
risk of slip-stick effect if the conveyor is running at high drive unit. Too much of the chain slack may cause high wear
chain tension. at the drive unit entry point. Chain slack of up to 150 mm
(5.9 in.) is acceptable during normal running but any slack
It is important for the chain to run in the correct direction. longer than that is not advisable. The chain slack might also
The chain is marked with direction of travel by an arrow on hit on any part below it. For this case, the chain slack should
the side of the chain. Over tensioning the chain can cause be shortened much earlier. In a normal case, chain should be
chain failure. Signs of over tensioning and overloading are shortened after run-in time of 40 hours. The next inspection
broken links or bent link pins. On catenary drive units it is should be made after 200 hours of running and then every
important that there is visible chain slack on the bottom of 1600 hours. More frequent inspections are recommended if
the drive units when running. the conveyor is long and has high load.
Chain Lubrication The chain should never be so tight that there is no slack
during the operation. If there is too much slack, there will be
Lubrication of the chain where it meets the slide rails and excessive wear on the chain guides and the chain. This could
inside by the pin and pivot location can reduce friction - be a risk for injury. If the slack on the conveyor chain is
allowing the chain to run more smoothly, quietly, and last unacceptably high, it must be shortened by splitting the
longer. Spray silicon with Teflon™ is the recommended chain and removing the necessary number of links.
lubrication, and can be applied at the drive tail to the inside • The conveyor chain must show some slack during opera-
of the chain through the slot in the catenary drive tails or tion (See Figure 98).
gravity take-up units. Figure 98
Wear
The degree of wear on a conveyor depends on a number of
factors, such as:
• Running time
• Load, contact pressure
• Speed
• Product accumulation
• Sharp or rough products
• Chemicals
Figure 98
• Foreign particles, e.g. chips, grinding particles, broken
glass, sand, sugar • The conveyor chain does not need to show any slack when
the conveyor chain is stationary or when a weighted take-
• Temperature up is used.
• Plain bends
Try to minimize the running time for the conveyor by
stopping it when there is no transport. Multiple horizontal
and vertical plain bends in a conveyor will often result in
increased wear.

Inspection Checking Slide Rail with the Conveyor
Chain in Place
Visually check the slide rail in horizontal and vertical bends
after every 200 hours of operation. The chain can stay in The slide rail needs to be checked after every 200 hours of
place during the inspection. Replace any worn out slide rail. operation. Check on a stationary state with the chain in
Remove the chain from the conveyor and inspect the slide place. Figure 99 shows the correct configuration of joints.
rail carefully once every 1500 hours of operation. Check for
any worn out slide rail and any other unusual conditions and
Figure 99
make necessary replacement. Clean up any dirt 20

accumulation in the conveyor beam, especially before any 10 60
plain bends, wheel bends, drive unit, and idler end.
35˚ 4
Drive Unit
5
The drive unit can be equipped with different gear motor FLOW
100
brands. Please follow the maintenance recommendations
from the manufacturer.
Maintenance Schedule
Maintenance is recommended to be carried out every 3rd,
6th and 12th month, and subsequently every 6th month, Figure 99
considering the running condition. Following are the • Check the screwing points on the slide rail.
recommended actions to be carried out:
• Check the joints section on the slide rail.
First 3rd Month, 6th Month, and Every 6th • Check that the gap (Figure 100, item 1) between the slide
rails and that the joints fit correctly.
Month Following Figure 100
• Shorten the chain, if required.

• Visually inspect the condition of the slide rail, sprocket,
wheel, and chain guides.
• Check any high wear part on the conveyor, and replace
X
when necessary.
• Clean up any foreign accumulation that might block the 1
smooth flow of the conveyor.
• Check the gearbox oil level and top off when necessary.
• Check all support structures, slide guides, and conveyor
joints for looseness. Replace when necessary.
Figure 100
• Check that the nylon screw is in place and does not pro-
trude over the surface of the slide rail.
• Check that the joint sections are not deformed.

Checks When the Chain is Removed Safety Devices
The slide rail needs to be checked once a year or after 1500 Safety devices should be checked at regular intervals.
hours of operation. The chain should be removed from the
conveyor beam for checking the slide rail. Check carefully • Check the motor cover for the suspended drive
on the condition of wear and the screws. (See Figure 101).
Figure 101
Horizontal Bends
Horizontal bends need to be checked carefully after every
200 hours of operation.
Check the inner slide rail in horizontal bends carefully, since
the friction here is particularly high. The conveyor chain
develops more pressure on the inner slide rail compared to
the outer slide rail.
• Check the slide rail for scratches and notches.
• Replace the slide rail and the screws, if necessary.
• Clean the conveyor chain and check the condition of the
chains.
• Clean the conveyor beam.
Figure 101
• This motor cover must always be in place when the con-
veyor is operating.
• The drive unit should always have a chain cover to protect
the safety of the users. The chain slack can be seen when
the conveyor is running at the drive unit. Check that the
chain cover plates are in place, and that the chain does not
slacken enough to hang below the plates (Figure 102).
Figure 102
X Figure 102
• Check that the chain cover is in place for the conveyor
chain on the intermediate drive units and the catenary
drive units.

Troubleshooting
Symptom Cause Corrective Action
Jerky running • Damage or badly fitted slide rail. • Inspect and replace as necessary.
• Incorrectly adjusted slip clutch. • Adjust slip clutch.
• Worn transmission parts. • Check/replace transmission chain, chain drive sprocket.
• Conveyor chain is too tight or • Lubricate chain with silicone spray with Teflon™.
loose.
• Tension conveyor chain correctly.
• Dirty conveyor.
• Clean conveyor chain/slide rail.
• Add weighted take-up.
Drive unit is running; conveyor • Incorrectly adjusted slip clutch. • Check adjustment of slip clutch.
chain is not running
• Friction discs in slip clutch are • Check and replace if necessary.
worn or contaminated.
• Check the free running of the conveyor chain.
• Damage/badly fitted slide rail.
• Check and fit.
• Transmission products are not fit-
ted.
Motor overheating on drive unit • Overloaded conveyor. • Remove products from conveyor and test run.
• Gearbox leaking oil. • Check actual conveyor load against recommended load-
ing. If possible, add breaks to add more drives.
• Dirty conveyor.
• Check output shaft seal and area around motor/gearbox
interface.
• Clean the conveyor chain with warm water.
Noise • Worn or damaged bearings in drive • Check/replace drive unit.
unit.
• Check the free running of the conveyor chain, especially
• Damage/badly fitted slide rail. in slide rail joints.
• Excessive conveyor speed. • Check actual load against recommended loading.
• Incorrect conveyor chain tension. • Lubricate chain with silicone spray with Teflon™.
• Lengthen or shorten conveyor chain.
Abnormal wear of plastic parts • Overloaded conveyor. • Remove products from conveyor and test run.
• Ambient temperature too high. • Check the free running of the conveyor chain.
• Foreign object dropped on the con- • Check actual conveyor load against recommended load-
veyor chain. ing. If possible, add breaks the conveyor and add more
drives.
• Check against recommended temperature for conveyor.
• Replace the broken section of chain.
Clutch Ratcheting or slipping • Excessive or accumulated load. • Avoid load buildup by running conveyor continuously.
• Improper ratchet clutch tensioning. • Do not manually surge load conveyor.
• Damaged or missing chain assem- • Refer to ratchet clutch adjustment in Maintenance.
bly parts.
• Review belt and repair or replace as required.
• Accumulation of conveyed material
• Remove chain and clean out.
or foreign objects inside of casing.

Required Tools
A WARNING
• 3/32" hex wrench
• 3 mm hex wrench
• 4 mm hex wrench
• 5 mm hex wrench
• 6 mm hex wrench SEVERE HAZARD!
• 8 mm hex wrench If conveyor chain is damaged or worn,
replace chain section.
• 10 mm wrench
• 13 mm wrench 2. Replace old section of chain.
• 16 mm wrench
• Chain Removal Tool A CAUTION
• Slide Rail Cutter DO NOT reuse chain rods that are damaged,
bent, or show signs of wear.
• Drill Fixtures for Slide Rails
• Riveting Tool
NOTE
Conveyor Chain Replacement Drive spindle shaft assembly replacement is
recommended with belt replacement (see
“Drive Spindle Shaft Replacement” on
A WARNING page 39).
SEVERE HAZARD!
LOCK OUT POWER before removing guards
or performing maintenance. Exposed moving
parts can cause serious injury.
Replacing a Section or Entire Chain

1. Use chain removal tool or a punch and hammer to push
the chain rod (Figure 103, item 1) out.
Figure 103
Figure 103

Conveyor Chain Tensioning Slide Rail Replacement
Replace the slide rails if they become worn.
A WARNING
NOTE
Top and bottom slide rails are shipped
pinned/attached at various places on
conveyor.
SEVERE HAZARD!
1. Remove belt. See “Conveyor Chain Replacement” on
LOCK OUT POWER before removing guards
page 37.
or performing maintenance. Exposed moving
parts can cause serious injury. 2. Drill out or push out drilled pinned screws or rivets
3. Remove slide rail (Figure 105, item 2) from top of
NOTE frame assembly.
Figure 105
Belt should not be stretched during

installation. A proper length of belt can be 2
installed by interlocking the ends by hand
without excess links.
1
1. Remove one or more chain links to take up tension.
Refer to “Replacing a Section or Entire Chain” on
page 37.
NOTE
After shortening chain, ensure there is visible
slack in chain (while running) at catenary Figure 105
drive tails. If chain is not visible in cover slot 4. Cut and remove worn slide rail section and replace with
(Figure 104, item 1) inspect from end.
new slide rail. See "Installation" section, starting on
Figure 104 page 15.
5. Remove lower slide rails, as needed, repeat procedure
used for upper slide rails.
6. Install new slide rails. See "Installation" section, starting
on page 15.
Idler Pulley Replacement
A WARNING
1
Figure 104 injury. LOCK OUT POWER before removing
1. Remove chain. See “Conveyor Chain Replacement” on
page 37.

2. Remove three flat head screws (Figure 106, item 1). Drive Spindle Shaft Replacement
Figure 106
1
A WARNING

1. Remove chain. See “Conveyor Chain Replacement” on
page 37.
Figure 106
2. Remove the gearmotor.
3. Remove the head plate (Figure 107, item 1) from the 3. Loosen two screws (Figure 109, item 1) on each side of
idler end. conveyor, and remove the drive tail assembly (Figure
Figure 107
109, item 2) from the conveyor frame (Figure

1 109, item 3).
Figure 109
3 2
Figure 107
4. Remove flat head screw (Figure 108, item 1) and Figure 109
remove idler pulley (Figure 108, item 2) from idler 4. Remove four screws (Figure 110, item 1) on side of
head plate assembly. drive spindle.
Figure 108
Figure 110
1
Figure 110
2
Figure 108
5. Install components reverse of removal.

5. Remove two screws (Figure 111, item 1) on side of 7. Remove the head plates (Figure 114, item 1) from the
drive spindle. drive tail.
Figure 111 Figure 114
1
2
Figure 111 1
6. Use the bearing tool (Figure 112, item 1) to unseat

bearings by inserting the four screws and turning the
threaded rod (Figure 112, item 2) to push bearing out.
NOTE: Insert the longer screws (Figure 112, item 3) on
the drive shaft side and the shorter screws (Figure
113, item 1) on the non-shaft side.
Figure 112
Figure 114
Retaining Guide Replacement

Cantenary Drive End
1. Remove three socket head screws (Figure 115, item 1)
3 and remove drive plate guard (Figure 115, item 2) from
drive plate (Figure 115, item 3).
Figure 115
1 2
Figure 112
Figure 113
1
1 2
Figure 115
Figure 113

2. Remove two socket head screws (Figure 116, item 1). 5. Remove upper retaining guide (Figure 119, item 1)
Figure 116
from drive plate (Figure 119, item 2).
Figure 119
Figure 119
Figure 116 6. Install components reverse of removal.
3. Remove lower retaining guide (Figure 117, item 1)
from drive plate (Figure 117, item 2). Idler End and GP Drive Tail
Figure 117
1. Remove seven (7) socket head screws (Figure
120, item 1) from idler head plate assembly.
2 Figure 120
1 1
1
Figure 117
4. Remove three socket head screws (Figure 118, item 1). Figure 120
Figure 118
2. Remove retaining guide (Figure 121, item 1) from idler
head plate assembly (Figure 121, item 2). Replace
components, as needed.
1
Figure 121
Figure 118
Figure 121

Wheel Bend Servicing Power Transfer
Removal
A WARNING
1. Remove two socket head screws (Figure 124, item 1)
and cover (Figure 124, item 2) from power transfer
assembly.
Figure 124

1. Remove screw (Figure 123, item 1) on both sides of
guard cover (Figure 123, item 2). Remove guard cover.
Figure 122
1 1
2
Figure 124
2 2. Loosen two socket head screws (Figure 125, item 1)
holding tensioning pulley (Figure 125, item 2) onto
Figure 122 timing belt (Figure 125, item 3).
Figure 125
2. Remove screws (Figure 123, item 1) from wheel guide

Figure 123
2
1
1
2 3
1
Figure 125
Figure 123
3. Remove timing belt (Figure 125, item 3) from
3. Replace wheel guide. assembly.

4. Loosen idler socket head screw (Figure 126, item 1) on
Figure 129
both sides of the conveyor.

Figure 126
1
1
2
Figure 126
5. Slide idler assembly within slot (Figure 126, item 2) to
remove tension on belt. Figure 129
6. Remove two socket head screws (Figure 127, item 1)
and pinch guard (Figure 127, item 2). NOTE
Figure 127
Note that head of pin (Figure 129, item 1)

1 should be removed in direction shown.
8. Remove belt.
9. Remove four socket head screws (Figure 130, item 1)
holding wear bar assembly (Figure 130, item 2) onto
power transfer.
2 Figure 130
2 1
Figure 127
7. Lift slightly on belt (Figure 128, item 1) and push pin
(Figure 128, item 2) out of belt.
Figure 128
1
2
1
Figure 130
Figure 128

10. Remove wear bar assembly (Figure 131, item 1) from 12. Remove socket head screw (Figure 133, item 1) on
power transfer. both sides of the conveyor and remove idler assembly.
Figure 133
Figure 131 13. Replace idler assembly (if worn), and install socket head
screws to secure.
11. Disassemble side guide plates (Figure 132, item 1), 14. Loosen two set screws (Figure 134, item 1) on two
wear rods (Figure 132, item 2), and wear bar (Figure bearings (Figure 134, item 2).
132, item 3). Replace worn components. Figure 134
Figure 132
1
3 1
2
2 1 Figure 134
15. Loosen sprocket set screws (Figure 134, item 3).
16. Remove drive shaft (Figure 135, item 1), making
certain not to loose key (Figure 135, item 2) when
removing gear (Figure 135, item 3).
2
3
Figure 135

17. Remove key (Figure 136, item 1) from sprocket 2. Secure drive shaft onto bearings with two set screws
(Figure 136, item 2). (Figure 138, item 1).
Figure 136
Figure 138
18. Replace worn drive sprockets and bearings.
3. Raise belt (Figure 139, item 1) into position, and move
gear (Figure 139, item 2) so that cogs line up with belt,
Installation
as shown.
1. Install drive shaft (Figure 137, item 1) on two bearings Figure 139
(Figure 137, item 2) and press outward as shown.

Figure 137
2 1
3
Figure 137
Figure 139
4. Tighten sprocket with set screws (Figure 139, item 3)
in proper alignment with belt (Figure 139, item 1).

5. Install wear bar assembly (Figure 140, item 1) with 7. Bring ends of belt together and install pin (Figure
four socket head screws (Figure 140, item 2). 142, item 1).
2
1

6. Guide belt (Figure 141, item 1) through idler assembly 8. Install pinch guard (Figure 143, item 1) with two
with belt routing under gear (Figure 141, item 2) and socket head screws (Figure 143, item 2).
over wear tube (Figure 141, item 3). Figure 143
Figure 141
3 1
Figure 143
Figure 141

9. Slide idler assembly within slot (Figure 144, item 1) • On idler end, route and install belt (Figure 146, item 1)
only enough to remove excess slack from belt (Figure as shown. Press up on tensioner (Figure 146, item 2) and
144, item 2). Tighten socket head screws (Figure tighten two socket head screws (Figure 146, item 3).
Figure 146
144, item 3). 1
A CAUTION 2
DO NOT overtighten belt or excessive wear
will occur.
Figure 144
3
1
Figure 146
3 • On drive end, route and install belt (Figure 147, item 1) as
shown. Press down on tensioner (Figure 147, item 2) and
tighten two socket head screws (Figure 147, item 3)
Figure 147
Figure 144
2
10. Rotate drive shaft (Figure 145, item 1) to verify
tightness of belt (Figure 145, item 2). Belt should turn
freely. Loosen idler socket head screw
(Figure 145, item 3) and adjust, if necessary.
Figure 145
3
1
Figure 147
12. Install cover (Figure 148, item 1) with two socket head
3 screws (Figure 148, item 2).
Figure 148
Figure 145
11. Install timing belt:
2
1
Figure 148

Service Parts
NOTE
For replacement parts other than those shown in this section, contact an authorized Dorner distributor or
Dorner directly. Recommended Critical Service Parts and Kits are identified by the Key Service Parts
symbol . Dorner recommends keeping these parts on hand.
Drive Tail
4 Drive Tail Kit

5
7
1
3
Optional Auxiliary Shaft Shown

Service Parts
Item Part Number Description Item Part Number Description
1 FSD63101-A-FK Retaining Guide Set (Pair) 4 FKDD-A45-EL Standard Load E-Drive 3/4” Drive
Tail Kit with Shaft in the 'A' Position
2 FSD63102-A-FK Belt Capture Guide Set (Pair) FKDD-A45-ER Standard Load E-Drive 3/4” Drive
Tail Kit with Shaft in the 'D' Position
3 205700-EN-045 Standard Load E-Drive 3/4” Spindle FKDD-A45-ELA Standard Load E-Drive 3/4” Drive
Shaft Assembly Tail Kit with Shaft in the 'A' Position
and Auxiliary Shaft
205700-EA-045 Standard Load E-Drive 3/4” Spindle
Shaft Assembly with Auxiliary Shaft FKDD-A45-ERA Standard Load E-Drive 3/4” Drive
205700-FN-045 Standard Load 20 mm Spindle Shaft
Assembly and Auxiliary Shaft
205700-FA-045 Standard Load 20 mm Spindle Shaft FKDD-A45PT-EL Standard Load E-Drive 3/4” Drive
Tail Kit with Shaft in the 'A' Position
Assembly with Auxiliary Shaft
and Power Transfer
205700-AN-045 Auxiliary Spindle Shaft Assembly
FKDD-A45PT-ER Standard Load E-Drive 3/4” Drive
205700-AA-045 Dual Auxiliary Spindle Shaft
Assembly and Power Transfer
FKDD-A45-0L Standard Load 20 mm Drive Tail Kit
with Shaft in the 'A' Position
FKDD-A45-0R Standard Load 20 mm Drive Tail Kit
with Shaft in the 'D' Position
FKDD-A45-0LA Standard Load 20 mm Drive Tail Kit
with shaft in the 'A' Position and
Auxiliary Shaft
FKDD-A45-0RA Standard Load 20 mm Drive Tail Kit
with shaft in the 'D' Position and
Auxiliary Shaft
FKDD-A45PT-0L Standard Load 20 mm Drive Tail Kit
with Shaft in the 'A' Position and
Power Transfer
FKDD-A45PT-0R Standard Load 20 mm Drive Tail Kit
with Shaft in the 'D' Position and
Power Transfer
FKDD-A45-AA Auxiliary Tail Kit with two Auxiliary
Shafts
FKDD-A45-AL Auxiliary Tail Kit with Shaft in the 'A'
Position
FKDD-A45-AR Auxiliary Tail Kit with Shaft in the 'D'
Position
5 FAEC-DS Plug
6 FLG-120-SF Drive Flange
207242 Drive Flange for Power Transfer
7 CP1005-1-SF Guard Plate (Pair - with screws)
Service parts can be obtained through your distributor or directly
from Dorner Mfg. Corp. (800) 397-8664 or
[email protected]

Service Parts
Guided Profile (GP) Drive Tail
4 Guided Profile Drive Tail Kit
1
1
3
3

Service Parts
1 FSE63001-A-FK Retaining Guide Set (Pair) 4 FKDD-A45GP-EL Standard Load E-Drive 3/4”
Drive Tail Kit with Shaft in the 'A'
Position
2 FAEC-IE-SF Idler Tail Cover (x10)
FKDD-A45GP-ER Standard Load E-Drive 3/4”
3 205700-EN-045 Standard Load E-Drive 3/4”
Spindle Shaft Assembly Drive Tail Kit with Shaft in the 'D'
Position
205700-EA-045 Standard Load E-Drive 3/4”
FKDD-A45GP-ELA Standard Load E-Drive 3/4”
Spindle Shaft Assembly with
Auxiliary Shaft
Position and Auxiliary Shaft
205700-FN-045 Standard Load 20 mm Spindle
Shaft Assembly FKDD-A45GP-ERA Standard Load E-Drive 3/4”
Drive Tail Kit with Shaft in the 'D'
205700-FA-045 Standard Load 20 mm Spindle
Position and Auxiliary Shaft
Shaft Assembly with Auxiliary
FKDD-A45GPPT-EL Standard Load E-Drive 3/4”
Shaft
205700-AN-045 Auxiliary Spindle Shaft Position and Power Transfer
Assembly
FKDD-A45GPPT-ER Standard Load E-Drive 3/4”
205700-AA-045 Dual Auxiliary Spindle Shaft
Drive Tail Kit with Shaft in the 'D'
Assembly
Position and Power Transfer
FKDD-A45GP-0L Standard Load 20 mm Drive Tail
Kit with Shaft in the 'A' Position
FKDD-A45GP-0R Standard Load 20 mm Drive Tail
Kit with Shaft in the 'D' Position
FKDD-A45GP-0LA Standard Load 20 mm Drive Tail
and Auxiliary Shaft
FKDD-A45GP-0RA Standard Load 20 mm Drive Tail
and Auxiliary Shaft
FKDD-A45GPPT-0L Standard Load 20 mm Drive Tail
and Power Transfer
FKDD-A45GPPT-0R Standard Load 20 mm Drive Tail
and Power Transfer
FKDD-A45GP-AA Auxiliary Tail Kit with two
Auxiliary Shafts
FKDD-A45GP-AL Auxiliary Tail Kit with Shaft in the
'A' Position
FKDD-A45GP-AR Auxiliary Tail Kit with Shaft in the
'D' Position
5 FLG-120-SF Drive Flange
207242 Drive Flange for Power Transfer
[email protected]

Service Parts
FKSD-A45 Suspended Drive
1
2
4 3
6 7 Suspended Drive Tail Kit

Service Parts
Item Part Number Description
1 FSD63101-A-FK Retaining Guide Set (Pair)
2 FSD63102-A-FK Belt Capture Guide Set (Pair)
3 205700-AN-045 Auxiliary Spindle Shaft Assembly
4 RS08BX19T-20 Sprocket, Solid (19T)

5 FATL-250 Torque Limiter Sprocket
(Max Pull 844N)
6 FRS008B-64LK Roller Chain
7 FKSD-A45-0L Suspended Drive Tail Kit with
Shaft in the ‘A’ Position
FKSD-A45-0R Suspended Drive Tail Kit with
Shaft in the ‘D’ Position
FKSD-A45GP-0L Suspended Guided Profile Drive
Tail Kit with Shaft in the ‘A’
Position
FKSD-A45GP-0R Suspended Guided Profile Drive
Tail Kit with Shaft in the ‘D’
Position
[email protected]

Service Parts
FKID-DD-0L1/0R1 Intermediate Direct Drive
3
4
5 1

1 FK-2013B-W30 FSID Drive Sprocket
2 FKD44504-1 FSD Steering Guide Right/Left
3 FKD44102 FSD Return Steering Guide R/L
4 CP1012-K Return Chain Protector
5 6904ZZ NTN Bearing
[email protected]

Service Parts
FKID-SD-0L1/0R1 Intermediate Suspended Drive
8 3
4 1
6
2
5
7

1 FK-2013B-W30 FSID Drive Sprocket
2 FKD44504-1 FSD Steering Guide Right/Left
3 FKD44102 FSD Return Steering Guide R/L
4 6904ZZ NTN Bearing
5 FATL-250 Sprocket
6 RS08BX19T-20 Transmission Sprocket
7 FRS008B-64LK Roller Chain
8 CP1012-K Return Chain Protector
[email protected]

Service Parts
Idler Tail
4 Idler Tail Kit

Service Parts
1 FSE63001-A-FK Retaining Guide Set (Pair)
2 FAEC-IE Idler Tail Cover (x10)

3 FSIM-A15 Idler Pulley Assembly
205700-AN-045 Idler Pulley Assembly with
Auxiliary Shaft
4 FKIE-A45 Idler Tail Kit
FKIE-A45-AL Idler Tail Kit with Auxiliary Shaft in
the 'A' Position
FKIE-A45-AR Idler Tail Kit with Auxiliary Shaft in
the 'D' Position (Shown)
FKIE-A45PT-L Idler Tail Kit with Shaft in the 'A'
FKIE-A45PT-R Idler Tail Kit with Shaft in the 'D'
[email protected]

Service Parts
Frame Assembly
3
1

1 See Slide Rail Section Slide Rails
2 FKCB-3-LLLLL Frame
3 FACS-20x140 Connecting Bracket, w/Set
Screws (x10)
LLLLL = Part length in inches with two decimal places.
Length Example: Length = 95.25" LLLLL = 09525
[email protected]

Service Parts
Curve Frame Assembly
3
3

1 See Slide Rail Slide Rails
Section
2 FKWB-AR150A Wheel Curve Kit
FKHB-AR500 90° 500 Radius
Plain Bend Curve Kit
FKHB-AR700 90° 700 Radius
Plain Bend Curve Kit
3 FSWH63001 Wheel Guide (Pair)
A = Curve Angle: 30, 45, 60, 90, 180
[email protected]

Service Parts
Knuckle Frame Assembly

1 See Slide Rail Slide Rails
Section
2 FKVB-5R-300 5° Knuckle Kit
FKVB-7R-300 7° Knuckle Kit
3 FACS-25x140A Connecting Bracket, w/Set
Screws (x10)
[email protected]

Service Parts
#4 & #5 High Sides for Straight Modules
5
3
2
4
1 6

1 FATB-20 Stud, M8 x 20 mm (x50)
2 204172-LLLLL 1.5" High Side
204127-LLLLL 3" High Side
3 204566 Mounting Clip
4 210829 Guide Clip Adapter
210831 Guide Clip Adapter
for Tail Mount Only
210836 Guide Clip Adapter
for Roller Transfer Tail Mount Only
5 920614M Socket Head Screw, M6-1.00 x 14 mm
6 990812M Hex Nut, M8-1.25
LLLLL = Part length in inches with two decimal places.
Length Example: Length = 95.25" LLLLL = 09525
[email protected]

Service Parts
#4 & #5 High Sides for Curve Modules
6
4
7
5
1

1 FATB-20 Stud, M8 x 20 mm (x50) 3 204137-045-AAA 1.50" High Side for Wheel Bend
2 204135-045-AAA 1.50" High Side for Wheel Bend Curves - Inside Edge
Curves - Outside Edge 204333-045-AAA 1.50" High Side for 500R Plain Bend
Curves - Inside Edge
204334-045-AAA 1.50" High Side for 500R Plain Bend
Curves - Outside Edge 204337-045-AAA 1.50" High Side for 700R Plain Bend
204338-045-AAA 1.50" High Side for 700R Plain Bend
Curves - Outside Edge 204136-045-AAA 3" High Side for Wheel Bend Curves -
204134-045-AAA 3" High Side for Wheel Bend Curves - Inside Edge
Outside Edge 204335-045-AAA 3" High Side for 500R Plain Bend
204336-045-AAA 3" High Side for 500R Plain Bend
Curves - Outside Edge 204339-045-AAA 3" High Side for 700R Plain Bend
204340-045-AAA 3" High Side for 700R Plain Bend
Curves - Outside Edge 4 204566 Mounting Clip
5 210829 Clip Guide Adapter
7 990812M Hex Nut, M8-1.25
AAA = Angle of curve: 030, 045, 060, 090, 180
[email protected]

Service Parts
#4 & #5 High Sides for Incline/Decline Modules
1 3

1 204342-AA-045 1.5” Guide Plate for Lower
knuckle
204343-AA-045 1.5” Guide Plate for Upper
knuckle
204144-AA-045 3” Guide Plate for Lower knuckle
204174-AA-045 3” Guide Plate for Upper Knuckle
3 990812M Hex Nut, M8-1.25
4 204145 Spacer
AA = Angle of bend: 05, 07, 10, 15, 20, 30, 45, 60, 90
[email protected]

Service Parts
#13 & #14 Heavy Duty Fully Adjustable Guiding
12
11
4
6
#13 Standard #14 Tool-Less
7 9
14
8
13
10
10 5
11
1
2
15 16
12

1 206380 Base 15 FGRR-15x20-LLLLL Guide Rail
2 206381 Base Clamp GTB13A04 Guide Rail 4' long
3 206382 Insert Clamp GTB13A08 Guide Rail 8' long
4 206383 Guide Ring 16 FGRT-3x33 1.3" UHMW Guiding (per foot)
5 206385 Tube GTB13B04 1.3" UHMW Guiding 4' long
6 206397 Clip GTB13B08 1.3" UHMW Guiding 8' long
7 206685 T-Nut 206683 2" UHMW Guiding (per foot)
8 206692 Guide Tube GTB13C04 2" UHMW Guiding 4' long
9 807-2859 Nylon Cap Screw, M6 x 16 mm GTB13C08 2" UHMW Guiding 8' long
10 807-920 Square Nut, M6-1.0 17 206686 Adjustable Bracket Assembly
11 911-710 Washer (Includes Items 1 through 14)
12 920616M Socket Head Screw, 206687 Tool-Less Adjustable Bracket
M6-1.00 x 16 mm Assembly (Includes Items 1 through
14)
206698 Knob, 12 mm (Tool-Less)
LLLLL = part length in inches with 2 decimal places
13 9206150M Socket Head Screw,
M6-1.00 x 150 mm Length Example: Length = 35.25" LLLLL = 03525
206697 Knob, 150 mm (Tool-Less) Service parts can be obtained through your distributor or directly
14 990601M Hex Nut
[email protected]

Service Parts
#17 & #18 - Puck / Pallet Guiding
7 4
3
2
6
5
1

2 FASN-M8 Square Nut, M8
3 205129 Clip
4 960882M Hex Head Flange Screw, M8 x 12 mm
5 990812M Hex Nut, M8-1.25
6 460055 Guide Rail (per foot)
7 203825 Clip On Slide Rail (per foot)
[email protected]

Service Parts
Type A - Fixed Guiding (16x54)
1 3
4
2

1 FGRB-16x54 Fixed Guide Rail Bracket (x10) 5 FGRR-15x20 Guide Rail (3 m long)
2 FGRD-6 Spacer (x10) 6 FGRT-3x23 Guiding (3 m long)
3 FATB-20 T-Bolt, 20 mm, use without spacer (x50) Service parts can be obtained through your distributor or directly
FATB-35 T-Bolt, 35 mm (x50) from Dorner Mfg. Corp. (800) 397-8664 or
[email protected]
4 990802M Hex Nut
Type B - Fixed Guiding (16x42)
1 3
4
2

1 FGRB-16x42 Fixed Guide Rail Bracket (x10) 6 FGRT-3x23 Guiding (3 m long)
2 FGRD-6 Spacer (x10) Service parts can be obtained through your distributor or directly
3 FATB-20 T-Bolt, 20 mm, use without spacer (x50) from Dorner Mfg. Corp. (800) 397-8664 or
[email protected]
FATB-35 T-Bolt, 35 mm (x50)
4 990802M Hex Nut
5 FGRR-15x20 Guide Rail (3 m long)

Service Parts
Type C - Fixed Guiding (28x42)
1 3
4
2

[email protected]
4 990802M Hex Nut
Type D - Fixed Guiding (40x42)
3
1

1 FGRB-40x42 Fixed Guide Rail Bracket (x10) 6 FGRT-3x23 Guiding (3 m long)
[email protected]
4 990802M Hex Nut

Service Parts
Type E - Fixed Guiding (49x42)
3
1
4 2

[email protected]
4 990802M Hex Nut
Type F - Fixed Guiding (53x42)
3
1
4 2

[email protected]
4 990802M Hex Nut

Service Parts
Type G - Fixed Guiding (90x42)

[email protected]
4 990802M Hex Nut
Type H - Adjustable Width Guiding (8x39x45)
2
4

1 FGRA-8x39x45 Fixed Guide Rail Bracket (x10) 5 FGRR-15x20 Guide Rail (3 m long)
[email protected]
4 990802M Hex Nut

Service Parts
Type J - Adjustable Width Guiding (26x39x45)
1 3
2
4

1 FGRA-26x39x45 Fixed Guide Rail Bracket (x10) 5 FGRR-15x20 Guide Rail (3 m long)
[email protected]
4 990802M Hex Nut
Type K - Adjustable Width Guiding (40x18)
1
3
7
2

1 FGRA-40x18 Fixed Guide Rail Bracket (x10) 7 FGRK-18x80A Guide Rail Support (x10)
[email protected]
4 990802M Hex Nut
6 FGRT-3x23 Guiding (3 m long)

Service Parts
Type L - Adjustable Height Guiding (18x110)
3
4
1
2

1 FGRF-42x18V Guide Rail Bracket (x10) 6 FGRR-15x20 Guide Rail (3 m long)
2 FGRD-18A Spacer (x10) 7 FGRT-3x23 Guiding (3 m long)
3 FGRL-18x110C Guide Rail Support (x10) Service parts can be obtained through your distributor or directly
[email protected]
FATB-35 T-Bolt, 35 mm, use with 1 spacer (x50)
FATB-53 T-Bolt, 53 mm, use with 2 spacers (x50)
5 990802M Hex Nut
Type M - Adjustable Height Guiding (18x150)
5
8
3
6
1
2
7

1 FGRF-42x18V Guide Rail Bracket (x10) 7 990802M Hex Nut
2 FGRD-18A Spacer (x10) 8 FGRR-15x20 Guide Rail (3 m long)
3 FGDT-150 Tube (x10) 9 FGRT-3x23 Guiding (3 m long)
4 FGRS-18 Guide Rail Support (x10) Service parts can be obtained through your distributor or directly
5 FGEC-18 Cap (x10) from Dorner Mfg. Corp. (800) 397-8664 or
[email protected]
6 FATB-20 T-Bolt, 20 mm, use without spacer (x50)

Service Parts
Type N - Fully Adjustable Guiding
10
3
9
2
8
6 4
1 1
5
7

1 FGRB-18x20 Guide Rail Bracket (x10) 6 FGEC-18 Cap (x10)
2 FGDT-70 Tube, 70 mm (x10) 7 FGEC-20 Cap (x10)
FGDT-100 Tube, 100 mm (x10) 8 FATB-20 T-Bolt, 20 mm (x50)
FGDT-150 Tube, 150 mm (x10) 9 FGRR-15x20 Guide Rail (3 m long)
3 FGRS-18 Guide Rail Support (x10) 10 FGRT-3x23 Guiding (3 m long)
4 FGSP-DT Tube Spacer (x10) Service parts can be obtained through your distributor or directly
5 FGGR-18x100 Guide Rail Tube, 100 mm (x10)
[email protected]
FGGR-18x150 Guide Rail Tube, 150 mm (x10)
FGGR-18x200 Guide Rail Tube, 200 mm (x10)
Type P - Fully Adjustable Guiding
2
4
3
1
6

1 FGRD-18A Spacer (x10) 5 FGRK-18x80A Guide Rail Support (x10)
2 FATB-20 T-Bolt, 20 mm, use without spacer (x50) 6 990802M Hex Nut
FATB-35 T-Bolt, 35 mm, use with 1 spacer (x50) 7 FGRR-15x20 Guide Rail (3 m long)
FATB-53 T-Bolt, 53 mm, use with 2 spacers (x50) 8 FGRT-3x23 Guiding (3 m long)
FATB-71 T-Bolt, 71 mm, use with 3 spacers (x50) Service parts can be obtained through your distributor or directly
3 FGRF-42x18V Guide Rail Bracket (x10)
[email protected]
4 FGRL-18x160CA Vertical Support (x10)

Service Parts
Type Q - Dual Rail Guiding
8
7
5
3
8
4
2
6 7
1

1 FGRD-18A Spacer (x10) 5 FGRK-18x80A Guide Rail Support (x10)
2 FATB-20 T-Bolt, 20 mm, use without spacer (x50) 6 990802M Hex Nut
FATB-35 T-Bolt, 35 mm, use with 1 spacer (x50) 7 FGRR-15x20 Guide Rail (3 m long)
FATB-53 T-Bolt, 53 mm, use with 2 spacers (x50) 8 FGRT-3x23 Guiding (3 m long)
3 FGRF-A110 Guide Rail Bracket (x10) Service parts can be obtained through your distributor or directly
4 FGRF-DP Plug (x10) from Dorner Mfg. Corp. (800) 397-8664 or
[email protected]
Type R - Dual Rail Guiding

8
5
3
6
1

1 FGRD-18A Spacer (x10) 7 FGRR-15x20 Guide Rail (3 m long)
2 FATB-20 T-Bolt, 20 mm, use without spacer (x50) 8 FGRT-3x23 Guiding (3 m long)
FATB-35 T-Bolt, 35 mm, use with 1 spacer (x50) Service parts can be obtained through your distributor or directly
FATB-53 T-Bolt, 53 mm, use with 2 spacers (x50) from Dorner Mfg. Corp. (800) 397-8664 or
[email protected]
3 FGRF-A35 Guide Rail Bracket (x10)
4 FGRF-DP Plug (x10)
5 FGRK-18x80A Guide Rail Support (x10)
6 990802M Hex Nut

Service Parts
Type S - Adjustable Height Guiding
6
8
4
1

1 FGRF-42x18V Guide Rail Bracket (x10)
2 FGRD-18A Spacer (x10)
3 FGRS-18 Guide Rail Support (x10)
4 FATB-20 T-Bolt, 20 mm, use without spacer (x50)
5 FGDT-200 Tube (x10)
6 FGEC-18 Cap (x10)
7 990802M Hex Nut
9 FGRT-3x23 Guiding (3 m long)
[email protected]

Service Parts
Power Transfer
19 10
22
11
3
14 27
29
16
28 27
13
5
26
21
1
25 6
23
20 32
7 24 12
15
2
4
9
30
31
17 18
23

1 802-046 Cam Bearing 17 203264-045 Shaft Assembly
2 802-110 Bearing 18 203267-045 Square Key, 3/16” x 105 mm
3 950620M Low Head Cap Screw, M6-1.00 x 20 mm 19 205727-045 Pinch Guard
4 203765 Locking Sprocket 20 350505 Power Transfer Cover
5 807-2285 Cover 21 605280P Washer
6 807-2286 Retaining Ring 22 910506M Button Head Screw, M5-0.80 x 6 mm
7 807-2287 Hex Post 23 950510M Low Head Cap Screw, M5-0.80 x 10 mm
8 206886 Pulley 24 950612M Low Head Cap Screw, M6-1.00 x 12 mm
9 907-115 Socket Head Set Screw, #10-32 x 0.19 25 950830M Low Head Cap Screw, M8-1.25 x 30 mm
10 203229 Side Guide Plate 26 970510M Socket Head Set Screw,
M5-0.80 x 10 mm
11 205711-045 Wear Bar 27 605279P Washer
28 814-105 Timing Belt 15 mm x 460 mm
12 203231 Timing Belt Tensioner
13 205710-02 Side Plate 29 990621M Insert
14 205726-045 Wear Rod 30 807-2277 Washer
31 203765P Sliding Sprocket
15 206343-045 Power Transfer Belt
32 970606M Cup Set Screw, M6-0.80 x 5 mm
16 205725-045 Tensioner Assembly Service parts can be obtained through your distributor or directly
[email protected]

Service Parts
Horizontal Mounting Brackets
2
6
1 5
1
5 6
3

1 FATB-20 Stud, M8 x 20 mm
2 FAHBS-80SPL Mounting Bracket
3 605279P Washer
4 920622M Socket Head Screw,
M6-1.00 x 22 mm
5 990602M Hex Nut, M6-1.00
6 990812M Flanged Hex Nut, M8-1.25
[email protected]

Service Parts
Support Post - Conveyor Frame Mount
3
2

1 FASL-M8 Spring Nut (x50) 7 960883M Flange Head Cap Screw,
2 FAVBS-60KV Mounting Bracket for 64 mm M8-1.25 x 16 mm
Stand 8 990812M Hex Nut, M8-1.25
3 FATB-20 T-Bolt, 20 mm (x50) LLLLL = Length in inches with 2 decimal places.
4 FBFT-64 Stand Foot for 64 mm Stand Length Example: Length = 95.25" LLLLL = 09525
w/Hardware Service parts can be obtained through your distributor or directly
5 FBSB-64X64-LLLLL Leg for 64 mm Stand from Dorner Mfg. Corp. (800) 397-8664 or
6 FBEC-64 Cover for 64 mm Stand (x10) [email protected]

Service Parts
Support Post - Motor Mount
10 5
1
6
4
7

1 207195-045 Stand Mounting Channel 8 FBFT-64 Stand Foot for 64 mm Stand
2 207194-LH Drive Tail Bracket, Left Hand w/Hardware
3 207194-RH Drive Tail Bracket, Right Hand 9 FBSB-64X64-LLLLL Leg for 64 mm Stand
4 990812M Hex Nut, M8-1.25 10 FBEC-64 Cover for 64 mm Stand (x10)
5 FBCS-20X96 Connecting Strip, 20 x 96 mm LLLLL = Length in inches with 2 decimal places.
(x10) Length Example: Length = 95.25" LLLLL = 09525
6 960882M Flange Head Cap Screw, Service parts can be obtained through your distributor or directly
M8-1.25 x 12 mm from Dorner Mfg. Corp. (800) 397-8664 or
7 FATB-20 T-Bolt, 20 mm [email protected]

Service Parts
Suspended Drive Stand
6 3
2
8

1 FBCS-20X76 Connecting Strip, 20 x 76 mm 7 960883M Flange Head Cap Screw,
(x10) M8-1.25 x 16 mm
2 206887 Bracket 8 960825M Hex Head Cap Screw, M8-1.25 x
3 207275 Nut Bar 25 mm
4 FBFT-64 Stand Foot for 64 mm Stand LLLLL = Length in inches with 2 decimal places.
w/Hardware Length Example: Length = 95.25" LLLLL = 09525
5 FBSB-64X64-LLLLL Leg for 64 mm Stand Service parts can be obtained through your distributor or directly
6 FBEC-64 Cover for 64 mm Stand (x10) from Dorner Mfg. Corp. (800) 397-8664 or
[email protected]

Service Parts
Dual Side Support Post
3 5
6
7
8
9
1

1 FBCS-20X55 Connecting Strip, 20 x 55 mm for 7 990812M Hex Nut, M8-1.25
64 mm Stand (x10) 8 960825M Hex Head Cap Screw, M8-1.25 x
2 FBFT-64 Stand Foot for 64 mm Stand 25 mm for 64 mm Stand
w/Hardware 9 FBSB-64X64-00039 Spacer
3 FATB-20 T-Bolt, 20 mm (x50) LLLLL = Length in inches with 2 decimal places.
4 FBSB-64X64-LLLLL Leg for 64 mm Stand Length Example: Length = 95.25" LLLLL = 09525
5 FBEC-64 Cover for 64 mm Stand (x10) Service parts can be obtained through your distributor or directly
6 FAAL-64 Mounting Bracket for 64 mm from Dorner Mfg. Corp. (800) 397-8664 or
Stand [email protected]

Service Parts
E-Drive Gearmotor Mounting Package
6
2

1 202270-00075 Extrusion
2 202971 Drive Plate
3 203065 Drive Spacer
4 350115 Adapter Ring
6 930625M Flat Head Screw, M6-1.00 x 25 mm
7 990601M Hex Nut, M6-1.00
8 931025M Flat Head Screw, M10-1.50 x 25 mm
9 911-108 Washer
[email protected]

Service Parts
Standard Load 90° Industrial
Gearmotors
1
2
Item Part No. Description

1 62MES411FN Motor, 0.25hp (0.19Kw), 115/230 Volts,
60 Hz, 1-Phase
62MES423FN Motor, 0.25hp (0.19Kw), 208−230/460
Volts, 60 Hz, 3-Phase
22MSD3DEN Motor, 0.25hp (0.19Kw), 130 VDC
62MEH411FN Motor, 0.5hp (0.37Kw), 115/230 Volts,
60Hz, 1−Phase
32MES423FN Motor, 0.5hp (0.37Kw) 208−230/460
Volts, 60Hz, 3 Phase
62MHD9DEN Motor, 0.5hp (0.37Kw), 90 VDC
32MES423EN Motor, 0.5hp (0.37Kw), 230 Volts, 3
Phase Inverter Duty
32MHD9DEN Motor, 0.75 hp, (0.56Kw), 90 VDC
2 32M005EL Gear Reducer, 5:1, NEMA 42CZ
32M010EL Gear Reducer, 10:1, NEMA 42CZ
32M005ES Gear Reducer, 5:1, NEMA 56C
32M010EH Gear Reducer, 10:1, NEMA 140 TC
[email protected]

Service Parts
Flange Mounted Motor (Direct Drive Tail)
Product Line FK,FS,FM,FU,FV FC,FL FS FM

Radius (M) 0.064 0.0675 0.044 0.049
Drive Type Direct Direct Intermediate Intermediate
Part Number
Right Hand Left Hand Speed Speed Speed Speed
FMM129RDS423EN FMM129LDS423EN 5.2 m/min 5.5 m/min 3.6 m/min 4 m/min
FMM067RDS423EN FMM067LDS423EN 10 m/min 10.6 m/min 6.9 m/min 7.7 m/min
FMM032RDS423EN FMM032LDS423EN 21.3 m/min 22.5 m/min 14.6 m/min 16.3 m/min
FMM013RDS423EN FMM013LDS423EN 52.2 m/min 55.1 m/min 35.9 m/min 40 m/min
Part Number Volts Phase Hz Power Power Speed Torque Torque Ratio Force
FMM129(X)DS423EN 230/460 3 60 0.18 kW 0.25 Hp 13 rpm 95 Nm 837 in-lb. 129 i 1484 N
FMM067(X)DS423EN 230/460 3 60 0.37 kW 0.50 Hp 25 rpm 79 Nm 699 in-lb. 67.5 i 1234 N
FMM015(X)DS423EN 230/460 3 60 0.55 kW 0.75 Hp 114 rpm 39 Nm 341 in-lb. 15 i 609 N
(X) = L or R for Right Hand o Left Hand Gearmotor matching RH or LH Drive
Note: speed range for 60 Hz gearmotors is 10 to 60 Hz or 6:1.

[email protected]

Service Parts
Foot Mounted Motor (Suspended Drive Tail)
Product Line FK,FS,FM,FU,FV FC,FL

Radius (M) 0.064 0.0675
Drive Type Suspended Suspended
Part Number
Right Hand nd Speed Speed
FMM129RSS423EN FMM129LSS423EN 5.2 m/min 5.5 m/min
FMM067RSS423EN FMM067LSS423EN 10 m/min 10.6 m/min
Part Number Volts Phase Hz Power Power Speed Torque Torque Force
FMM129(X)SS423EN 230/460 3 60 0.18 kW 0.25 Hp 13 rpm 95 Nm 837 in-lb. 129 i 1484 N
FMM067(X)SS423EN 230/460 3 60 0.37 kW 0.50 Hp 25 rpm 79 Nm 699 in-lb. 67.5 i 1234 N
FMM015(X)SS423EN 230/460 3 60 0.55 kW 0.75 Hp 114 rpm 39 Nm 341 in-lb. 15 i 609 N
(X) = L or R for Right Hand o Hand Gearmotor matching RH or LH Drive
Note: speed range for 60Hz gearmotors is 10 to 60 Hz or 6:1.

[email protected]

Service Parts
Slide Rail Replacement Tool Replacement Chain
Replacement chain sold per box containing 5 meters of
chain.
For specific chain details see FlexMove Engineering
Manual.
3 1

1 203475-FK Slide Rail Replacement Tool Kit
Part Number Description
2 807-3928 Nylon Socket Screw, FKPC-5 Standard Plastic Chain
#6-40 x 3/4" (x50) FKPC-5CD Conductive Chain
3 896-790 Drill Bit, #18, 0.1695" FKFT-5 Friction Top Chain
Service parts can be obtained through your distributor or directly FKWT-5PR Wedge Top Chain, Right
from Dorner Mfg. Corp. (800) 397-8664 or FKWT-5PL Wedge Top Chain, Left
[email protected] FKWT-5C Wedge Top Chain
FKWT-5D Wedge Top Chain
Slide Rail FKFK-5 Flocked Chain
Service parts can be obtained through your distributor or
Item Part No. Description directly from Dorner Mfg. Corp. (800) 397-8664 or
1 FASR-25 Standard HDPE (25 M Roll) [email protected]
FASR-25U Standard Low Friction UHMW
(25 M Roll)
FASR-25A Special Conductive
(25 M Roll)
FASR-25X Special HI Speed
(25 M Roll)
FASR-25P Special Abrasive Resistant
(25 M Roll)
FASR-25T Special Abrasive Resistant,
High Load (25 M Roll)
FASR-25MDS Special High Load Nylon
(25 M Roll)
[email protected]

Service Parts
Belt Removal Tool Utility Cutter

1 203480 Belt Removal Tool
1 897-1099 Utility Cutter
[email protected] Service parts can be obtained through your distributor or directly
[email protected]
Side Cutter
Bearing Tool

1 206891 Bearing Tool
Item Part Number Description from Dorner Mfg. Corp. (800) 397-8664 or
1 897-1098 Side Cutter [email protected]
[email protected]

Notes

Return Policy
Returns must have prior written factory authorization or they will not be accepted. Items that are returned to Dorner without authorization will not
be credited nor returned to the original sender. When calling for authorization, please have the following information ready for the Dorner factory
representative or your local distributor:
1. Name and address of customer.
2. Dorner part number(s) of item(s) being returned.
3. Reason for return.
4. Customer's original order number used when ordering the item(s).
5. Dorner or distributor invoice number. Include part serial number if available.
A representative will discuss action to be taken on the returned items and provide a Returned Materials Authorization (RMA) number for
reference. RMA will automatically close 30 days after being issued. To get credit, items must be new and undamaged. There will be a return
charge on all items returned for credit, where Dorner was not at fault. It is the customer’s responsibility to prevent damage during return
shipping. Damaged or modified items will not be accepted. The customer is responsible for return freight.
Product Type
Standard Products Engineered to
order parts
Product Line Conveyors Gearmotors Support Accessories Spare Parts Spare Belts Spare Belts - Spare Belts - All equipment
& Mounting Stands (non-belt) - Standard Cleated & Plastic Chain and parts
Packages Flat Fabric Spec. Fabric
1100 Series
2200 Series
30% return fee for all products except:
3200 Series 50% return fee for conveyors with modular belt,
Pallet Systems cleated belt or speciality belts
FlexMove/SmartFlex
GAL Series All Electrical items are assigned original manufacturers return policy.
non-returnable case-by-case
All Electrical
7100 Series
7200/7300 Series
AquaGard 7350 50% return fee for all products
Series Version 2
GES Series
AquaGard
7350/7360 Series non-returnable
AquaPruf Series
Returns will not be accepted after 60 days from original invoice date. The return charge covers inspection, cleaning, disassembly, disposal and
reissuing of components to inventory. If a replacement is needed prior to evaluation of returned item, a purchase order must be issued. Credit (if
any) is issued only after return and evaluation is complete.
Dorner has representatives throughout the world. Contact Dorner for the name of your local representative. Our Customer Service Team will
gladly help with your questions on Dorner products.
For a copy of Dorner's Warranty, contact Dorner, an authorized sales channel or visit our website: www.dorner.com.
For replacement parts, contact an authorized Dorner Service Center or the factory.
851-904 Rev. A Printed in U.S.A.

Flexmove FK (45 MM) Conveyor System: Installation, Maintenance & Parts Manual

Uploaded by

Copyright:

Available Formats

Flexmove FK (45 MM) Conveyor System: Installation, Maintenance & Parts Manual

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Flexmove FK (45 MM) Conveyor System: Installation, Maintenance & Parts Manual

Uploaded by

Copyright:

Available Formats

FlexMove FK (45 mm)

For other service manuals visit our website at:

Record Conveyor Serial Number Here

FlexMove FK (45 mm) Conveyor System

FlexMove FK (45 mm) Conveyor System

FlexMove FK (45 mm) Conveyor System

Dorner cannot control the physical

DO NOT OPERATE CONVEYORS IN AN

Exposed moving parts can cause severe

Gearmotors may be HOT.

FlexMove FK (45 mm) Conveyor System

FlexMove FK (45 mm) Conveyor System

FlexMove FK (45 mm) Conveyor System

End Drive Unit

FlexMove FK (45 mm) Conveyor System

• Drill fixtures for slide rail

• M8 = Washer, Countersink Cap Screw, Nut, Lock Nut

FlexMove FK (45 mm) Conveyor System

turning in slot. The indication groove in the T-bolt should be

Pre installation Information

FlexMove FK (45 mm) Conveyor System

fasten foot connecting strips to the inner side of the foot.

2. Slide the connecting strips (Figure 11, item 1) into the

FlexMove FK (45 mm) Conveyor System

purpose but are connected to the structural beams in different

FlexMove FK (45 mm) Conveyor System

FlexMove FK (45 mm) Conveyor System

Drive Tail Support Brackets

in the same way. If the conveyor beam is too 2

Drive Unit and Idler End Unit

FlexMove FK (45 mm) Conveyor System

Beam Correct Installation

FlexMove FK (45 mm) Conveyor System

Slide Rail End Installation at

FlexMove FK (45 mm) Conveyor System

Drilling Slide Rail

FlexMove FK (45 mm) Conveyor System

The beginning of each slide rail section must be fixed to the

FlexMove FK (45 mm) Conveyor System

FlexMove FK (45 mm) Conveyor System

FlexMove FK (45 mm) Conveyor System

FlexMove FK (45 mm) Conveyor System

Length Adjustment of the Conveyor Chain Guide Rail System Installation

the beam profile. The clamp should be placed over the

Intermediate Drive Units and Horizontal Bend Drive 3 1

FlexMove FK (45 mm) Conveyor System

Be certain that slot (Figure 59, item 3) is

4. Tighten nuts (Figure 59, item 2).

FlexMove FK (45 mm) Conveyor System

(Figure 63, item 2) to remove clip (Figure 64, item 1).

65, item 2).

FlexMove FK (45 mm) Conveyor System

1. Install clip assembly (Figure 69, item 1) into side rail

2. Fasten clip (Figure 69, item 1) to conveyor with nut 1

FlexMove FK (45 mm) Conveyor System

73, item 2).

FlexMove FK (45 mm) Conveyor System

77, item 1) with T-bolt (Figure 77, item 2).

2. Attach the bracket onto conveyor beam and tighten with