Accelerator Control System: Section

ENGINE
ACCELERATOR CONTROL SYSTEM

SECTION ACC ACC
E
CONTENTS
PRECAUTION ............................................... 2 REMOVAL AND INSTALLATION ................ 3 F
PRECAUTIONS ................................................... 2 ACCELERATOR CONTROL SYSTEM .............. 3

Precaution for Supplemental Restraint System Exploded View .......................................................... 3 G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- Removal and Installation .......................................... 3
SIONER" ................................................................... 2 Inspection ................................................................. 3
H
ACC-1 GETtheMANUALS.org
PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000006752514
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
The vehicle may be equipped with a passenger air bag deactivation switch. Because no rear seat exists where
a rear-facing child restraint can be placed, the switch is designed to turn off the passenger air bag so that a
rear-facing child restraint can be used in the front passenger seat. The switch is located in the center of the
instrument panel, near the ashtray. When the switch is turned to the ON position, the passenger air bag is
enabled and could inflate for certain types of collision. When the switch is turned to the OFF position, the pas-
senger air bag is disabled and will not inflate. A passenger air bag OFF indicator on the instrument panel lights
up when the passenger air bag is switched OFF. The driver air bag always remains enabled and is not affected
by the passenger air bag deactivation switch.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
• The vehicle may be equipped with a passenger air bag deactivation switch which can be operated by
the customer. When the passenger air bag is switched OFF, the passenger air bag is disabled and
will not inflate. When the passenger air bag is switched ON, the passenger air bag is enabled and
could inflate for certain types of collision. After SRS maintenance or repair, make sure the passenger
air bag deactivation switch is in the same position (ON or OFF) as when the vehicle arrived for ser-
vice.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
< REMOVAL AND INSTALLATION >
REMOVAL AND INSTALLATION A
Exploded View INFOID:0000000006405536
ACC
JPBIA4114GB J
1. Accelerator pedal assembly 2. Brake pedal bracket

A. Locating hook B. Locating pin
K
: N·m (kg-m, in-lb)
Removal and Installation INFOID:0000000006405537

L
REMOVAL
1. Disconnect accelerator pedal position sensor harness connector. M
2. Loosen mounting bolts, and remove accelerator pedal assembly.
CAUTION:
• Never disassemble accelerator pedal assembly. Never remove accelerator pedal position sensor N
from accelerator pedal assembly.
• Avoid impact from dropping etc. during handling.
• Be careful to keep accelerator pedal assembly away from water.
O
INSTALLATION
Note the following, and install in the reverse order of removal.
• Insert the locating pin while inserting the locating hook in to the break pedal bracket. Tighten mounting bolts
P
to accelerator pedal assembly.
CAUTION:
Never squeeze the locating hook into the break pedal bracket when inserting the locating pin into the
hole on the brake pedal bracket side.
Inspection INFOID:0000000006405538
INSPECTION AFTER INSTALLATION

< REMOVAL AND INSTALLATION >
• Check accelerator pedal moves smoothly within the whole operation range when it is fully depressed and
released.
• Check accelerator pedal securely returns to the fully released position.
• For the electrical inspection of accelerator pedal position sensor. Refer to following;
- MR16DDT: EC-387, "Component Inspection"
- HR16DE: EC-749, "Component Inspection"
- K9K: EC-1001, "Component Inspection"
CAUTION:
When harness connector of accelerator pedal position sensor is disconnected, perform “ACCELERA-
TOR PEDAL RELEASED POSITION LEARNING”. Refer to following;
• MR16DDT: EC-129, "Work Procedure"
• HR15DE: EC-547, "Work Procedure"
• K9K: EC-925, "DTC Logic"

Accelerator Control System: Section

Uploaded by

Copyright:

Available Formats

Accelerator Control System: Section

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Accelerator Control System: Section

Uploaded by

Copyright:

Available Formats

ENGINE

ACCELERATOR CONTROL SYSTEM

PRECAUTIONS ................................................... 2 ACCELERATOR CONTROL SYSTEM .............. 3

1. Accelerator pedal assembly 2. Brake pedal bracket

Removal and Installation INFOID:0000000006405537

INSPECTION AFTER INSTALLATION

You might also like