Original BMW Accessories.

Installation Instructions.
Alarm Kit
BMW 1 Series Coupe (E 82), Select Vehicle Production 12/07 - On

Vehicle must have optional alarm pre-wiring (SA 5GA), which is 100% option for US spec
vehicles.

Retrofit kit No. 65 73 0 444 089

Installation time
The installation time is 1.0 hours, but this may vary depending on the condition of the car and the
equipment in it.
Suggested installation time includes re-coding of the vehicle only for this retrofit kit. This time is based
on a vehicle that is at the current software level and does not require any updates. Before installing this
accessory into the vehicle, the vehicle should be connected to the DIS and checked for software
updates. If updates are available the vehicle should be programmed prior to installing this accessory.
If vehicle is under warranty, the costs of programming prior to retrofit should use defect code
72 60 93 02 00.
Please refer to SI B09 05 01 for latest BMW approved CIP Retrofit procedures.
Please refer to SI B01 09 06 – Defect Code for Programming Prior to Accessory Retrofit.

Important information
The instructions below are developed for BMW vehicles and are not to be compared to any other
existing instructions for vehicles other than BMW. No methods other than those specified in this
document are to be used for installation in BMW vehicles. Left and right are determined from the driver’s
seat.
Carefully read all instructions and supplements before proceeding with the installation. Reference
should be made to TIS for instructions dealing with a stock part of the vehicle but not stated in detail in
these instructions.
The instructions were complete and up to date at time of publication; however, changes to the vehicle
or installation may have occurred. Please report any problems or changes noted with the installation to
BMW Technical Hotline, along with VIN, date of manufacture and as much detail as possible.
Do not archive the hard copy of these installation instructions since daily updates are made by ASAP.

© BMW AG, München 01 29 0 444 091 2/2008 (Z/Z) 1

PARTS INFORMATION

Contents of Kit – P/N 65 73 0 444 089

Description Qty BMW Part Number

Bracket for hood switch 1 61 31 6 932 791

Mounting plate 1 65 75 6 936 588

Bracket for Alternate Power Siren 1 65 75 6 940 124

Alternate Power Siren/Tilt Sensor 1 65 75 9 124 581

Screw ST 4.8x13 1 07 11 9 906 163

Ultrasonic Module Interior Sensor 1 65 75 9 149 671

Hood Switch 1 61 31 9 119 052

Hex Nut M6 with captive washer 4 07 12 9 904 008

Hex Bolt M6 with washer 2 07 12 9 904 868

© BMW AG, München 01 29 0 444 091 2/2008 (Z/Z) 2

Contents

Section Page

1. Interior Ultrasonic Module Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2. Hood Switch Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3. Alternate Power Siren/Tilt Sensor Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4. Retrofit coding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

5. Personal Profile Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

6. Functional Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

© BMW AG, München 01 29 0 444 091 2/2008 (Z/Z) 3

1. Interior Ultrasonic Module Installation

1.1
Disconnect negative battery terminal.
2
1.2
Remove ceiling light cover (1) from ceiling light
housing (2) using Special Tool 00 9 341.
Refer to TIS 63 31 004.

1
082 006 US

1.3
Install ultrasonic module (1) into ceiling light as
shown.
1.4
Connect 8-position black connector (2) to
ultrasonic module (1).
2
1.5
Reinstall ceiling light cover to headliner.

1
082 007 US

© BMW AG, München 01 29 0 444 091 2/2008 (Z/Z) 4

2. Hood Switch Installation

2.1
Locate 3-position black hood switch connector
1 (1). Remove securing tape and protective cover.

082 008 US

Note: Make sure "corner notch" on bracket

faces reward and fits into base mounting tab
as shown.
2 2.2
Position hood switch bracket (2) to mounting
3 location (1) and secure in place with ST 4.8 x 13
screw (3).
1

S65 05 U09

2.3
Insert hood switch (1) into hood switch
bracket (2).
2 1

2.4
Connect hood switch connector (3) to hood
switch (2).

082 010 US

© BMW AG, München 01 29 0 444 091 2/2008 (Z/Z) 5

3. Alternate Power Siren/Tilt Sensor Installation

3.1
Remove LH rear wheel.
3.2
Remove LH rear wheel arch cover.
Refer to TIS 51 71 041
1 3.3
Locate 3-position black siren connector (1) in
upper LH wheel arch area. Remove securing
tape and protective cover.

090 0004 US

3.4
Install siren bracket (1) over threaded studs and
secure in place with three M6 hex nuts (2).

090 0005 US

3.5
2 Position siren (2) to mounting plate (3) and
secure in place with M6 hex nut (1).
1
3

082 011 US

© BMW AG, München 01 29 0 444 091 2/2008 (Z/Z) 6

3. Alternate Power Siren/Tilt Sensor Installation

3.6
Connect 3-position black connector (1) to
siren (2).
3.7
2 1 Push harness retainer into access hole on siren
bracket to keep harness properly positioned.

082 012 US

3.8
3 Use M6x18 hex bolts (1) to secure mounting
plate (2) to bracket (3).
2 3.9
Reinstall LH rear wheel arch cover.
3.10
1 Reinstall LH wheel.

Installation complete.

Please complete retrofit coding procedures

090 0008 US on the next page.

© BMW AG, München 01 29 0 444 091 2/2008 (Z/Z) 7

4. Retrofit coding

Note: Please refer to SI B09 05 01 for latest Progman retrofit procedure before starting vehicle
coding.
Reconnect negative battery terminal.
Retrofit DWA (alarm system) using Progman CIP 27.2 or later .
Follow approved Progman Retrofit procedures until Retrofit selection appears then:
Program session
Program selection:
- Select “Load SW”
Have control modules been replaced on this car?
- Select “No”
Screen will appear stating “Fitted control modules are being determined, followed by Select control
module to be processed”
- Select “Retrofits”
Screen will appear stating “Selecting Retrofits”
- Select “Retrofits”
Screen will appear stating “Retrofits have been added”
- Select “DWA”
Screen will appear stating “Select sub function for retrofits or cancel with arrow in navigational column
- Select “Added”
Screen will appear stating “Retrofitting Antitheft alarm system selected
- Select “Continue”
Screen will appear stating “The voltage is being tested; vehicle context is being checked again” followed
by “Measures plan is being determined”
Screen will appear stating “A measures plan has been created and accepted. It takes 1 minute to
execute this measures plan”
- Select “Start”
Screen will appear stating “The CKM values are being saved”; “The GM control module __________”;
“The CKM values are being restored”
Final Report
- Select “Finish”
To determine if DWA code number K302 is in vehicle order (VO)
- Select “Change”
- Select “Vehicle”
- Select “Complete encoding”
Screen will appear stating “You start coding the entire vehicle with the following functions
- Select “Continue”
Screen will appear stating “Should coding of the entire car be started now?”
- Select “Yes”
Screen will appear stating “Measures Plan is being determined”
Screen option will appear showing Measures Plan, DWA option code number K302 should be the last
number listed in the vehicle order.
- Select “Print” if a printed copy of measures plan is desired.
- Select “End” NOTE: DO NOT SELECT ACCEPT
Upon completion of anti-theft alarm system coding, conduct alarm system test to verify functionality of
alarm system.

© BMW AG, München 01 29 0 444 091 2/2008 (Z/Z) 8

5. Personal Profile Settings

Personal Profile Settings allow the customer to modify select settings for the Alarm system.
For vehicles with optional Navigation (SA 609):
- Settings can be selected via iDrive menu.
Please refer customer to Vehicle Owner’s Manual “Personal Profiles” and “Alarm” sections
for more information.

For vehicles without Navigation:

- The visual and audio confirmation settings can be modified via the Settings and Information on the
Instrument Cluster using the left hand stalk.
- All settings are set to active by default.
Please refer customer to Vehicle Owner’s Manual “Alarm System” and “Settings and
Information” sections for more information.

© BMW AG, München 01 29 0 444 091 2/2008 (Z/Z) 9

6. Functional Test

Upon completion of retrofit coding, verify that alarm system is working correctly by going through the
following action and response steps in order listed to ensure alarm system is functioning properly.

Action Response

Lock vehicle and arm alarm system with remote All doors, hood and trunk lock at same time. Alarm
key by pressing the round “Roundel” button on status LED on rearview mirror will start flashing
remote key. approximately once every 3 seconds indicating
properly functioning alarm system.

Vehicle is locked and alarm system armed but This indicates a secure point (i.e. a door, the trunk
alarm status LED flashes rapidly for about 20 or hood) is not secure or interior sensor is not
times, then flashes normally at 3 second intervals. properly connected. Locate and correct cause of
secure point fault and retry locking vehicle and
arming alarm system with remote key.

Check functionality of hood switch. Open vehicle hood. Pull up on hood switch contact
point to place hood switch in “test mode”. This
action simulates that hood is closed to alarm
control module while vehicle hood is physically
open.

Lock vehicle and arm alarm system with remote Verify that alarm status LED on rearview mirror is
key. flashing normally at 3 second intervals.

Push down on hood switch contact point. This task should result in alarm siren sounding!
Press “arrow” button on remote key to disarm
alarm.
If alarm siren fails to sound, verify siren/tilt sensor is
properly connected and repeat above procedure.

Unlock vehicle and disarm alarm system with

remote key. Close vehicle hood. Open driver's
door and sit in driver's seat. Place key in ignition.
Open all door windows. Exit vehicle and close
driver's door.
Verify that all doors, hood and trunk are closed and
secure.
Lock vehicle and arm alarm system with remote All doors, hood and trunk lock at same time and
key. interior sensor is activated. Alarm status LED on
rearview mirror will start flashing approximately
once every 3 seconds indicating properly
functioning alarm system.
Wait about 2 minutes for interior sensor to fully
recognize interior parameters of vehicle.

Pass your arm through driver's door open window This task should result with alarm siren sounding!
towards center console area in an attempt to Press "arrow" button on remote key to disarm
activate alarm interior sensor. alarm.

© BMW AG, München 01 29 0 444 091 2/2008 (Z/Z) 10

6. Functional Test

Action Response

Check functionality of tilt sensor. Close all doors, hood and trunk.

Lock vehicle and arm alarm system with remote Verify that alarm status LED on rearview mirror is
key. flashing normally at 3 second intervals.

Place a floor jack under any one of the four lift This task should result with alarm siren sounding!
points. Begin jacking vehicle up. Press "arrow" button on remote key to disarm
alarm.

Alarm status LED on rearview mirror flashes once Contact BMW Technical Hotline stating problem.
every 3 seconds indication properly functioning It may be necessary for a modified vehicle order file
alarm system, but alarm siren will not sound when be sent to you for loading into the vehicle's vehicle
passing your arm through driver's door open order to initiate proper function of alarm system.
window towards center console area in an attempt
to activate alarm interior sensor.

A modified vehicle order has been installed. Verify that alarm system is working correctly by
going through the above action and response
steps.

© BMW AG, München 01 29 0 444 091 2/2008 (Z/Z) 11