Scribd Logo
Upload

Welcome to Scribd!

  • 16 views

    Quick Guide For Gas Detection System Salwico SW2020

    Uploaded by

    fatzosidze
    The document provides instructions for using a gas sampling system. It details how to disconnect and reconnect sampling points, purge sampling points, measure single points, calibrate the system, reset alarms, and reset faults.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd

    Quick Guide For Gas Detection System Salwico SW2020

    Uploaded by

    fatzosidze
    16 views2 pages
    The document provides instructions for using a gas sampling system. It details how to disconnect and reconnect sampling points, purge sampling points, measure single points, calibrate the system, reset alarms, and reset faults.

    Original Description:

    Quick guide for gas detection system Salwico SW2020

    Original Title

    Quick guide for gas detection system Salwico SW2020

    Copyright

    © © All Rights Reserved

    Available Formats

    DOC, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides instructions for using a gas sampling system. It details how to disconnect and reconnect sampling points, purge sampling points, measure single points, calibrate the system, reset alarms, and reset faults.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    16 views2 pages

    Quick Guide For Gas Detection System Salwico SW2020

    Uploaded by

    fatzosidze
    The document provides instructions for using a gas sampling system. It details how to disconnect and reconnect sampling points, purge sampling points, measure single points, calibrate the system, reset alarms, and reset faults.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    of 2

    QUICK REFERENCE GUIDE FOR USING OF GAS SAMPLING SYSTEM

    “Salwico SW2020”

    WARNING: BEFORE BALLASTING OF BALLAST TANKS, THE


    CORRESPONDING SAMPLING-POINTS MUST BE DISCONNECTED
    FROM THE SAMPLING SEQUENCE AT THE SW2020 CONTROL UNIT.
    THIS WILL AVOID WATER BEING SUCKED INTO THE PIPES AND
    DAMAGING THE SYSTEM
    IMPORTANT NOTES:
    THE PRESSURE AIR TO THE SYSTEM MUST NEVER BE SHUT OFF.
    THE MANUAL SHUT-OFF VALVES SHALL DURING NORMAL
    OPERATION AND WHEN THERE IS WATER IN THE WATER BALLAST
    TANKS REMAIN OPEN. THIS WILL KEEP THE COUNTER-PRESSURE-
    AIR FLOW AND AVOID WATER ENTERING THE PIPES.

    1. DISCONNECTION
    a. SAMPLING POINT LIST
    b. CHOOSE A POINT BY ADJUSTING OF ARROW KEY
    c. F2 (DISCONNECT)
    d. F1 (DISCONNECT COMPLETION)
    e. USE HOME KEY FOR RETURN TO THE MEASUREMENT OF ALL
    SAMPLING-POINTS CONNECTED TO THE SAMPLING SEQUENCE

    WHEN THE BALLAST TANKS ARE EMPTY, THE


    CORRESPONDING SAMPLING-POINTS SHALL BE
    RECONNECTED
    2. RECONNECTION
    a. DISCONNECTION LIST
    b. CHOOSE A POINT BY ADJUSTING OF ARROW KEY
    c. F1 (RECONNECT)
    d. F1 (YES) FUNCTION OF PURGE DURING 2 MINUTES BEFORE
    RECONNECTON
    e. USE HOME KEY FOR RETURN TO THE MEASUREMENT OF ALL
    SAMPLING-POINTS CONNECTED TO THE SAMPLING SEQUENCE

    3. PURGE
    a. SAMPLING POINT LIST
    b. CHOOSE A POINT BY ADJUSTING OF ARROW KEY
    c. F4 (PURGE)
    d. USE F1 KEY OR ESC KEY FOR STOPPING
    e. USE HOME KEY FOR RETURN TO THE MEASUREMENT OF ALL
    SAMPLING-POINTS CONNECTED TO THE SAMPLING SEQUENCE

    4. MEASURE OF SINGLE POINT


    a. SAMPLING POINT LIST
    b. CHOOSE A POINT BY ADJUSTING OF ARROW KEY
    c. F3 (MEASURE) VARIOUS TIME IS ABLE TO BE INPUTTED
    BUT 5 MINUTES IS SET AT FIRST
    d. F1 (MEASURE)
    e. PUSH DOWN ESC KEY TWO TIMES FOR STOPPING
    5. CALIBRATION
    a. GENERAL SETTING SET UP
    b. CHOOSE “CHANGE LEVEL ACCESS” BY ADJUSTING OF ARROW
    KEY
    c. 3333 -> ENTER
    d. CHOOSE SUB MENU (13a) adjust zero BY ADJUSTING OF
    ARROW KEY
    e. F1(CONTINUE) -> F1(ADJUST)
    f. WHEN GET DISPLAY READINGS “ZERO CALIBRATION DONE”
    PUSH ESC (EXIT)
    g. CHOOSE SUB MENU (12a) calibration span on a gas detector BY
    ADJUSTING OF ARROW KEY
    h. F1 (CONTINUE)
    i. SUB MENU (12b) for entering % of LEL (C3H8) (50 for C3H8) ->
    ENTER
    j. F1 (CONTINUE)
    k. OPEN THE VALVE ON CYLINDER WITH TEST GAS
    l. F1 (START)
    m. WHEN THE LEVEL OF LEL WILL RICH 50% PUSH
    F1(CALIBRATE)
    n. WHEN GET DISPLAY READINGS “CALIBRATION DONE” PUSH
    F2 (EXIT)
    o. SUM MENU 12 (e) CLOSE THE VALVE ON CYLINDER WITH TEST
    GAS
    p. F1(EXIT)
    q. CHOOSE SUBMENU 10 restart the system with saving of current
    set up BY ADJUSTING OF ARROW KEY
    r. F1 (RESTART)

    6. ALARM RESET
    a. IN CASE OF SEVERAL POINT ALARMS ARE HAPPENED
    1) PUSH THE ALARM MUTE TO STOP BUZZER WHEN
    BUZZER IS RINGING FOR ALARM
    2) CHECK A ALARM PLACE AFTER PUSHING OF ALARM
    LIST
    3) PUSH DOWN THE ALARM RESET
    b. IN CASE OF ONE POINT ALARM IS HAPPENED
    1) PUSH THE ALARM MUTE TO STOP BUZZER WHEN
    BUZZER IS RINGING FOR ALARM
    2) PUSH DOWN THE ALARM RESET

    7. FAULT RESET
    a. PUSH DOWN THE MUTE TO STOP A BUZZER DURING BUZZER
    IS RINGING DUE TO FAULT
    b. PUSH DOWN THE FAULT LIST AND CHECK A KIND OF FAULT
    c. PUSH DOWN THE RESET

    You might also like